diff options
Diffstat (limited to 'drivers/usb/serial')
71 files changed, 5322 insertions, 4940 deletions
diff --git a/drivers/usb/serial/Kconfig b/drivers/usb/serial/Kconfig index 76f46224173..3ce5c74b29e 100644 --- a/drivers/usb/serial/Kconfig +++ b/drivers/usb/serial/Kconfig @@ -4,7 +4,7 @@ menuconfig USB_SERIAL tristate "USB Serial Converter support" - depends on USB + depends on TTY ---help--- Say Y here if you have a USB device that provides normal serial ports, or acts like a serial device, and you want to connect it to @@ -51,6 +51,24 @@ config USB_SERIAL_GENERIC support" be compiled as a module for this driver to be used properly. +config USB_SERIAL_SIMPLE + tristate "USB Serial Simple Driver" + help + Say Y here to use the USB serial "simple" driver. This driver + handles a wide range of very simple devices, all in one + driver. Specifically, it supports: + - Suunto ANT+ USB device. + - Fundamental Software dongle. + - HP4x calculators + - a number of Motorola phones + - Siemens USB/MPI adapter. + - ViVOtech ViVOpay USB device. + - Infineon Modem Flashloader USB interface + - ZIO Motherboard USB serial interface + + To compile this driver as a module, choose M here: the module + will be called usb-serial-simple. + config USB_SERIAL_AIRCABLE tristate "USB AIRcable Bluetooth Dongle Driver" help @@ -158,14 +176,6 @@ config USB_SERIAL_FTDI_SIO To compile this driver as a module, choose M here: the module will be called ftdi_sio. -config USB_SERIAL_FUNSOFT - tristate "USB Fundamental Software Dongle Driver" - ---help--- - Say Y here if you want to use the Fundamental Software dongle. - - To compile this driver as a module, choose M here: the - module will be called funsoft. - config USB_SERIAL_VISOR tristate "USB Handspring Visor / Palm m50x / Sony Clie Driver" help @@ -462,14 +472,34 @@ config USB_SERIAL_MOS7840 To compile this driver as a module, choose M here: the module will be called mos7840. If unsure, choose N. -config USB_SERIAL_MOTOROLA - tristate "USB Motorola Phone modem driver" +config USB_SERIAL_MXUPORT + tristate "USB Moxa UPORT Serial Driver" ---help--- - Say Y here if you want to use a Motorola phone with a USB - connector as a modem link. + Say Y here if you want to use a MOXA UPort Serial hub. + + This driver supports: + + [2 Port] + - UPort 1250 : 2 Port RS-232/422/485 USB to Serial Hub + - UPort 1250I : 2 Port RS-232/422/485 USB to Serial Hub with + Isolation + + [4 Port] + - UPort 1410 : 4 Port RS-232 USB to Serial Hub + - UPort 1450 : 4 Port RS-232/422/485 USB to Serial Hub + - UPort 1450I : 4 Port RS-232/422/485 USB to Serial Hub with + Isolation + + [8 Port] + - UPort 1610-8 : 8 Port RS-232 USB to Serial Hub + - UPort 1650-8 : 8 Port RS-232/422/485 USB to Serial Hub + + [16 Port] + - UPort 1610-16 : 16 Port RS-232 USB to Serial Hub + - UPort 1650-16 : 16 Port RS-232/422/485 USB to Serial Hub To compile this driver as a module, choose M here: the - module will be called moto_modem. If unsure, choose N. + module will be called mxuport. config USB_SERIAL_NAVMAN tristate "USB Navman GPS device" @@ -525,14 +555,6 @@ config USB_SERIAL_SPCP8X5 To compile this driver as a module, choose M here: the module will be called spcp8x5. -config USB_SERIAL_HP4X - tristate "USB HP4x Calculators support" - help - Say Y here if you want to use an Hewlett-Packard 4x Calculator. - - To compile this driver as a module, choose M here: the - module will be called hp4x. - config USB_SERIAL_SAFE tristate "USB Safe Serial (Encapsulated) Driver" @@ -540,14 +562,6 @@ config USB_SERIAL_SAFE_PADDED bool "USB Secure Encapsulated Driver - Padded" depends on USB_SERIAL_SAFE -config USB_SERIAL_SIEMENS_MPI - tristate "USB Siemens MPI driver" - help - Say M here if you want to use a Siemens USB/MPI adapter. - - To compile this driver as a module, choose M here: the - module will be called siemens_mpi. - config USB_SERIAL_SIERRAWIRELESS tristate "USB Sierra Wireless Driver" help @@ -639,21 +653,34 @@ config USB_SERIAL_OPTICON To compile this driver as a module, choose M here: the module will be called opticon. -config USB_SERIAL_VIVOPAY_SERIAL - tristate "USB ViVOpay serial interface driver" - help - Say Y here if you want to use a ViVOtech ViVOpay USB device. +config USB_SERIAL_XSENS_MT + tristate "Xsens motion tracker serial interface driver" + help + Say Y here if you want to use Xsens motion trackers. - To compile this driver as a module, choose M here: the - module will be called vivopay-serial. + This driver supports the new generation of motion trackers + by Xsens. Older devices can be accessed using the FTDI_SIO + driver. + + To compile this driver as a module, choose M here: the + module will be called xsens_mt. -config USB_SERIAL_ZIO - tristate "ZIO Motherboard USB serial interface driver" +config USB_SERIAL_WISHBONE + tristate "USB-Wishbone adapter interface driver" help - Say Y here if you want to use ZIO Motherboard. + Say Y here if you want to use a USB attached Wishbone bus. + + Wishbone is an open hardware SoC bus commonly used in FPGA + designs. Bus access can be serialized using the Etherbone + protocol <http://www.ohwr.org/projects/etherbone-core>. + + This driver is intended to be used with devices which attach + their internal Wishbone bus to a USB serial interface using + the Etherbone protocol. A userspace library is required to + speak the protocol made available by this driver as ttyUSBx. To compile this driver as a module, choose M here: the - module will be called zio. + module will be called wishbone-serial. config USB_SERIAL_ZTE tristate "ZTE USB serial driver" diff --git a/drivers/usb/serial/Makefile b/drivers/usb/serial/Makefile index 3b3e7308d47..bfdafd34944 100644 --- a/drivers/usb/serial/Makefile +++ b/drivers/usb/serial/Makefile @@ -24,9 +24,7 @@ obj-$(CONFIG_USB_SERIAL_EDGEPORT_TI) += io_ti.o obj-$(CONFIG_USB_SERIAL_EMPEG) += empeg.o obj-$(CONFIG_USB_SERIAL_F81232) += f81232.o obj-$(CONFIG_USB_SERIAL_FTDI_SIO) += ftdi_sio.o -obj-$(CONFIG_USB_SERIAL_FUNSOFT) += funsoft.o obj-$(CONFIG_USB_SERIAL_GARMIN) += garmin_gps.o -obj-$(CONFIG_USB_SERIAL_HP4X) += hp4x.o obj-$(CONFIG_USB_SERIAL_IPAQ) += ipaq.o obj-$(CONFIG_USB_SERIAL_IPW) += ipw.o obj-$(CONFIG_USB_SERIAL_IR) += ir-usb.o @@ -39,7 +37,7 @@ obj-$(CONFIG_USB_SERIAL_MCT_U232) += mct_u232.o obj-$(CONFIG_USB_SERIAL_METRO) += metro-usb.o obj-$(CONFIG_USB_SERIAL_MOS7720) += mos7720.o obj-$(CONFIG_USB_SERIAL_MOS7840) += mos7840.o -obj-$(CONFIG_USB_SERIAL_MOTOROLA) += moto_modem.o +obj-$(CONFIG_USB_SERIAL_MXUPORT) += mxuport.o obj-$(CONFIG_USB_SERIAL_NAVMAN) += navman.o obj-$(CONFIG_USB_SERIAL_OMNINET) += omninet.o obj-$(CONFIG_USB_SERIAL_OPTICON) += opticon.o @@ -50,16 +48,16 @@ obj-$(CONFIG_USB_SERIAL_QCAUX) += qcaux.o obj-$(CONFIG_USB_SERIAL_QUALCOMM) += qcserial.o obj-$(CONFIG_USB_SERIAL_QT2) += quatech2.o obj-$(CONFIG_USB_SERIAL_SAFE) += safe_serial.o -obj-$(CONFIG_USB_SERIAL_SIEMENS_MPI) += siemens_mpi.o obj-$(CONFIG_USB_SERIAL_SIERRAWIRELESS) += sierra.o +obj-$(CONFIG_USB_SERIAL_SIMPLE) += usb-serial-simple.o obj-$(CONFIG_USB_SERIAL_SPCP8X5) += spcp8x5.o obj-$(CONFIG_USB_SERIAL_SSU100) += ssu100.o obj-$(CONFIG_USB_SERIAL_SYMBOL) += symbolserial.o obj-$(CONFIG_USB_SERIAL_WWAN) += usb_wwan.o obj-$(CONFIG_USB_SERIAL_TI) += ti_usb_3410_5052.o obj-$(CONFIG_USB_SERIAL_VISOR) += visor.o +obj-$(CONFIG_USB_SERIAL_WISHBONE) += wishbone-serial.o obj-$(CONFIG_USB_SERIAL_WHITEHEAT) += whiteheat.o obj-$(CONFIG_USB_SERIAL_XIRCOM) += keyspan_pda.o -obj-$(CONFIG_USB_SERIAL_VIVOPAY_SERIAL) += vivopay-serial.o -obj-$(CONFIG_USB_SERIAL_ZIO) += zio.o +obj-$(CONFIG_USB_SERIAL_XSENS_MT) += xsens_mt.o obj-$(CONFIG_USB_SERIAL_ZTE) += zte_ev.o diff --git a/drivers/usb/serial/aircable.c b/drivers/usb/serial/aircable.c index 6d110a3bc7e..80a9845cd93 100644 --- a/drivers/usb/serial/aircable.c +++ b/drivers/usb/serial/aircable.c @@ -10,9 +10,9 @@ * * The device works as an standard CDC device, it has 2 interfaces, the first * one is for firmware access and the second is the serial one. - * The protocol is very simply, there are two posibilities reading or writing. + * The protocol is very simply, there are two possibilities reading or writing. * When writing the first urb must have a Header that starts with 0x20 0x29 the - * next two bytes must say how much data will be sended. + * next two bytes must say how much data will be sent. * When reading the process is almost equal except that the header starts with * 0x00 0x20. * @@ -31,15 +31,15 @@ * * The driver registers himself with the USB-serial core and the USB Core. I had * to implement a probe function against USB-serial, because other way, the - * driver was attaching himself to both interfaces. I have tryed with different + * driver was attaching himself to both interfaces. I have tried with different * configurations of usb_serial_driver with out exit, only the probe function * could handle this correctly. * * I have taken some info from a Greg Kroah-Hartman article: * http://www.linuxjournal.com/article/6573 * And from Linux Device Driver Kit CD, which is a great work, the authors taken - * the work to recompile lots of information an knowladge in drivers development - * and made it all avaible inside a cd. + * the work to recompile lots of information an knowledge in drivers development + * and made it all available inside a cd. * URL: http://kernel.org/pub/linux/kernel/people/gregkh/ddk/ * */ @@ -119,9 +119,8 @@ static int aircable_probe(struct usb_serial *serial, return 0; } -static int aircable_process_packet(struct tty_struct *tty, - struct usb_serial_port *port, int has_headers, - char *packet, int len) +static int aircable_process_packet(struct usb_serial_port *port, + int has_headers, char *packet, int len) { if (has_headers) { len -= HCI_HEADER_LENGTH; @@ -132,7 +131,7 @@ static int aircable_process_packet(struct tty_struct *tty, return 0; } - tty_insert_flip_string(tty, packet, len); + tty_insert_flip_string(&port->port, packet, len); return len; } @@ -141,28 +140,22 @@ static void aircable_process_read_urb(struct urb *urb) { struct usb_serial_port *port = urb->context; char *data = (char *)urb->transfer_buffer; - struct tty_struct *tty; int has_headers; int count; int len; int i; - tty = tty_port_tty_get(&port->port); - if (!tty) - return; - has_headers = (urb->actual_length > 2 && data[0] == RX_HEADER_0); count = 0; for (i = 0; i < urb->actual_length; i += HCI_COMPLETE_FRAME) { len = min_t(int, urb->actual_length - i, HCI_COMPLETE_FRAME); - count += aircable_process_packet(tty, port, has_headers, + count += aircable_process_packet(port, has_headers, &data[i], len); } if (count) - tty_flip_buffer_push(tty); - tty_kref_put(tty); + tty_flip_buffer_push(&port->port); } static struct usb_serial_driver aircable_device = { diff --git a/drivers/usb/serial/ark3116.c b/drivers/usb/serial/ark3116.c index a88882c0e23..1532cde8a43 100644 --- a/drivers/usb/serial/ark3116.c +++ b/drivers/usb/serial/ark3116.c @@ -23,7 +23,6 @@ */ #include <linux/kernel.h> -#include <linux/init.h> #include <linux/ioctl.h> #include <linux/tty.h> #include <linux/slab.h> @@ -43,7 +42,7 @@ #define DRIVER_NAME "ark3116" /* usb timeout of 1 second */ -#define ARK_TIMEOUT (1*HZ) +#define ARK_TIMEOUT 1000 static const struct usb_device_id id_table[] = { { USB_DEVICE(0x6547, 0x0232) }, @@ -62,8 +61,6 @@ static int is_irda(struct usb_serial *serial) } struct ark3116_private { - wait_queue_head_t delta_msr_wait; - struct async_icount icount; int irda; /* 1 for irda device */ /* protects hw register updates */ @@ -73,7 +70,7 @@ struct ark3116_private { __u32 lcr; /* line control register value */ __u32 hcr; /* handshake control register (0x8) * value */ - __u32 mcr; /* modem contol register value */ + __u32 mcr; /* modem control register value */ /* protects the status values below */ spinlock_t status_lock; @@ -146,7 +143,6 @@ static int ark3116_port_probe(struct usb_serial_port *port) if (!priv) return -ENOMEM; - init_waitqueue_head(&priv->delta_msr_wait); mutex_init(&priv->hw_lock); spin_lock_init(&priv->status_lock); @@ -343,18 +339,15 @@ static void ark3116_close(struct usb_serial_port *port) { struct usb_serial *serial = port->serial; - if (serial->dev) { - /* disable DMA */ - ark3116_write_reg(serial, UART_FCR, 0); - - /* deactivate interrupts */ - ark3116_write_reg(serial, UART_IER, 0); + /* disable DMA */ + ark3116_write_reg(serial, UART_FCR, 0); - usb_serial_generic_close(port); - if (serial->num_interrupt_in) - usb_kill_urb(port->interrupt_in_urb); - } + /* deactivate interrupts */ + ark3116_write_reg(serial, UART_IER, 0); + usb_serial_generic_close(port); + if (serial->num_interrupt_in) + usb_kill_urb(port->interrupt_in_urb); } static int ark3116_open(struct tty_struct *tty, struct usb_serial_port *port) @@ -407,31 +400,10 @@ err_out: return result; } -static int ark3116_get_icount(struct tty_struct *tty, - struct serial_icounter_struct *icount) -{ - struct usb_serial_port *port = tty->driver_data; - struct ark3116_private *priv = usb_get_serial_port_data(port); - struct async_icount cnow = priv->icount; - icount->cts = cnow.cts; - icount->dsr = cnow.dsr; - icount->rng = cnow.rng; - icount->dcd = cnow.dcd; - icount->rx = cnow.rx; - icount->tx = cnow.tx; - icount->frame = cnow.frame; - icount->overrun = cnow.overrun; - icount->parity = cnow.parity; - icount->brk = cnow.brk; - icount->buf_overrun = cnow.buf_overrun; - return 0; -} - static int ark3116_ioctl(struct tty_struct *tty, unsigned int cmd, unsigned long arg) { struct usb_serial_port *port = tty->driver_data; - struct ark3116_private *priv = usb_get_serial_port_data(port); struct serial_struct serstruct; void __user *user_arg = (void __user *)arg; @@ -440,8 +412,8 @@ static int ark3116_ioctl(struct tty_struct *tty, /* XXX: Some of these values are probably wrong. */ memset(&serstruct, 0, sizeof(serstruct)); serstruct.type = PORT_16654; - serstruct.line = port->serial->minor; - serstruct.port = port->number; + serstruct.line = port->minor; + serstruct.port = port->port_number; serstruct.custom_divisor = 0; serstruct.baud_base = 460800; @@ -453,29 +425,6 @@ static int ark3116_ioctl(struct tty_struct *tty, if (copy_from_user(&serstruct, user_arg, sizeof(serstruct))) return -EFAULT; return 0; - case TIOCMIWAIT: - for (;;) { - struct async_icount prev = priv->icount; - interruptible_sleep_on(&priv->delta_msr_wait); - /* see if a signal did it */ - if (signal_pending(current)) - return -ERESTARTSYS; - if ((prev.rng == priv->icount.rng) && - (prev.dsr == priv->icount.dsr) && - (prev.dcd == priv->icount.dcd) && - (prev.cts == priv->icount.cts)) - return -EIO; - if ((arg & TIOCM_RNG && - (prev.rng != priv->icount.rng)) || - (arg & TIOCM_DSR && - (prev.dsr != priv->icount.dsr)) || - (arg & TIOCM_CD && - (prev.dcd != priv->icount.dcd)) || - (arg & TIOCM_CTS && - (prev.cts != priv->icount.cts))) - return 0; - } - break; } return -ENOIOCTLCMD; @@ -573,14 +522,14 @@ static void ark3116_update_msr(struct usb_serial_port *port, __u8 msr) if (msr & UART_MSR_ANY_DELTA) { /* update input line counters */ if (msr & UART_MSR_DCTS) - priv->icount.cts++; + port->icount.cts++; if (msr & UART_MSR_DDSR) - priv->icount.dsr++; + port->icount.dsr++; if (msr & UART_MSR_DDCD) - priv->icount.dcd++; + port->icount.dcd++; if (msr & UART_MSR_TERI) - priv->icount.rng++; - wake_up_interruptible(&priv->delta_msr_wait); + port->icount.rng++; + wake_up_interruptible(&port->port.delta_msr_wait); } } @@ -596,13 +545,13 @@ static void ark3116_update_lsr(struct usb_serial_port *port, __u8 lsr) if (lsr&UART_LSR_BRK_ERROR_BITS) { if (lsr & UART_LSR_BI) - priv->icount.brk++; + port->icount.brk++; if (lsr & UART_LSR_FE) - priv->icount.frame++; + port->icount.frame++; if (lsr & UART_LSR_PE) - priv->icount.parity++; + port->icount.parity++; if (lsr & UART_LSR_OE) - priv->icount.overrun++; + port->icount.overrun++; } } @@ -659,7 +608,7 @@ static void ark3116_read_int_callback(struct urb *urb) } -/* Data comes in via the bulk (data) URB, erors/interrupts via the int URB. +/* Data comes in via the bulk (data) URB, errors/interrupts via the int URB. * This means that we cannot be sure which data byte has an associated error * condition, so we report an error for all data in the next bulk read. * @@ -674,7 +623,6 @@ static void ark3116_process_read_urb(struct urb *urb) { struct usb_serial_port *port = urb->context; struct ark3116_private *priv = usb_get_serial_port_data(port); - struct tty_struct *tty; unsigned char *data = urb->transfer_buffer; char tty_flag = TTY_NORMAL; unsigned long flags; @@ -689,10 +637,6 @@ static void ark3116_process_read_urb(struct urb *urb) if (!urb->actual_length) return; - tty = tty_port_tty_get(&port->port); - if (!tty) - return; - if (lsr & UART_LSR_BRK_ERROR_BITS) { if (lsr & UART_LSR_BI) tty_flag = TTY_BREAK; @@ -703,12 +647,11 @@ static void ark3116_process_read_urb(struct urb *urb) /* overrun is special, not associated with a char */ if (lsr & UART_LSR_OE) - tty_insert_flip_char(tty, 0, TTY_OVERRUN); + tty_insert_flip_char(&port->port, 0, TTY_OVERRUN); } - tty_insert_flip_string_fixed_flag(tty, data, tty_flag, + tty_insert_flip_string_fixed_flag(&port->port, data, tty_flag, urb->actual_length); - tty_flip_buffer_push(tty); - tty_kref_put(tty); + tty_flip_buffer_push(&port->port); } static struct usb_serial_driver ark3116_device = { @@ -726,7 +669,8 @@ static struct usb_serial_driver ark3116_device = { .ioctl = ark3116_ioctl, .tiocmget = ark3116_tiocmget, .tiocmset = ark3116_tiocmset, - .get_icount = ark3116_get_icount, + .tiocmiwait = usb_serial_generic_tiocmiwait, + .get_icount = usb_serial_generic_get_icount, .open = ark3116_open, .close = ark3116_close, .break_ctl = ark3116_break_ctl, diff --git a/drivers/usb/serial/belkin_sa.c b/drivers/usb/serial/belkin_sa.c index b72a4c16670..15bc71853db 100644 --- a/drivers/usb/serial/belkin_sa.c +++ b/drivers/usb/serial/belkin_sa.c @@ -18,14 +18,13 @@ * driver * * TODO: - * -- Add true modem contol line query capability. Currently we track the + * -- Add true modem control line query capability. Currently we track the * states reported by the interrupt and the states we request. * -- Add support for flush commands */ #include <linux/kernel.h> #include <linux/errno.h> -#include <linux/init.h> #include <linux/slab.h> #include <linux/tty.h> #include <linux/tty_driver.h> @@ -242,7 +241,6 @@ static void belkin_sa_process_read_urb(struct urb *urb) { struct usb_serial_port *port = urb->context; struct belkin_sa_private *priv = usb_get_serial_port_data(port); - struct tty_struct *tty; unsigned char *data = urb->transfer_buffer; unsigned long flags; unsigned char status; @@ -259,10 +257,6 @@ static void belkin_sa_process_read_urb(struct urb *urb) if (!urb->actual_length) return; - tty = tty_port_tty_get(&port->port); - if (!tty) - return; - if (status & BELKIN_SA_LSR_ERR) { /* Break takes precedence over parity, which takes precedence * over framing errors. */ @@ -276,13 +270,12 @@ static void belkin_sa_process_read_urb(struct urb *urb) /* Overrun is special, not associated with a char. */ if (status & BELKIN_SA_LSR_OE) - tty_insert_flip_char(tty, 0, TTY_OVERRUN); + tty_insert_flip_char(&port->port, 0, TTY_OVERRUN); } - tty_insert_flip_string_fixed_flag(tty, data, tty_flag, + tty_insert_flip_string_fixed_flag(&port->port, data, tty_flag, urb->actual_length); - tty_flip_buffer_push(tty); - tty_kref_put(tty); + tty_flip_buffer_push(&port->port); } static void belkin_sa_set_termios(struct tty_struct *tty, diff --git a/drivers/usb/serial/bus.c b/drivers/usb/serial/bus.c index 37decb13d7e..9374bd2aba2 100644 --- a/drivers/usb/serial/bus.c +++ b/drivers/usb/serial/bus.c @@ -38,15 +38,14 @@ static int usb_serial_device_match(struct device *dev, return 0; } -static ssize_t show_port_number(struct device *dev, +static ssize_t port_number_show(struct device *dev, struct device_attribute *attr, char *buf) { struct usb_serial_port *port = to_usb_serial_port(dev); - return sprintf(buf, "%d\n", port->number - port->serial->minor); + return sprintf(buf, "%d\n", port->port_number); } - -static DEVICE_ATTR(port_number, S_IRUGO, show_port_number, NULL); +static DEVICE_ATTR_RO(port_number); static int usb_serial_device_probe(struct device *dev) { @@ -80,7 +79,7 @@ static int usb_serial_device_probe(struct device *dev) goto exit_with_autopm; } - minor = port->number; + minor = port->minor; tty_register_device(usb_serial_tty_driver, minor, dev); dev_info(&port->serial->dev->dev, "%s converter now attached to ttyUSB%d\n", @@ -98,13 +97,22 @@ static int usb_serial_device_remove(struct device *dev) struct usb_serial_port *port; int retval = 0; int minor; + int autopm_err; port = to_usb_serial_port(dev); if (!port) return -ENODEV; - /* make sure suspend/resume doesn't race against port_remove */ - usb_autopm_get_interface(port->serial->interface); + /* + * Make sure suspend/resume doesn't race against port_remove. + * + * Note that no further runtime PM callbacks will be made if + * autopm_get fails. + */ + autopm_err = usb_autopm_get_interface(port->serial->interface); + + minor = port->minor; + tty_unregister_device(usb_serial_tty_driver, minor); device_remove_file(&port->dev, &dev_attr_port_number); @@ -112,39 +120,43 @@ static int usb_serial_device_remove(struct device *dev) if (driver->port_remove) retval = driver->port_remove(port); - minor = port->number; - tty_unregister_device(usb_serial_tty_driver, minor); dev_info(dev, "%s converter now disconnected from ttyUSB%d\n", driver->description, minor); - usb_autopm_put_interface(port->serial->interface); + if (!autopm_err) + usb_autopm_put_interface(port->serial->interface); + return retval; } -static ssize_t store_new_id(struct device_driver *driver, +static ssize_t new_id_store(struct device_driver *driver, const char *buf, size_t count) { struct usb_serial_driver *usb_drv = to_usb_serial_driver(driver); - ssize_t retval = usb_store_new_id(&usb_drv->dynids, driver, buf, count); + ssize_t retval = usb_store_new_id(&usb_drv->dynids, usb_drv->id_table, + driver, buf, count); if (retval >= 0 && usb_drv->usb_driver != NULL) retval = usb_store_new_id(&usb_drv->usb_driver->dynids, + usb_drv->usb_driver->id_table, &usb_drv->usb_driver->drvwrap.driver, buf, count); return retval; } -static ssize_t show_dynids(struct device_driver *driver, char *buf) +static ssize_t new_id_show(struct device_driver *driver, char *buf) { struct usb_serial_driver *usb_drv = to_usb_serial_driver(driver); return usb_show_dynids(&usb_drv->dynids, buf); } +static DRIVER_ATTR_RW(new_id); -static struct driver_attribute drv_attrs[] = { - __ATTR(new_id, S_IRUGO | S_IWUSR, show_dynids, store_new_id), - __ATTR_NULL, +static struct attribute *usb_serial_drv_attrs[] = { + &driver_attr_new_id.attr, + NULL, }; +ATTRIBUTE_GROUPS(usb_serial_drv); static void free_dynids(struct usb_serial_driver *drv) { @@ -163,7 +175,7 @@ struct bus_type usb_serial_bus_type = { .match = usb_serial_device_match, .probe = usb_serial_device_probe, .remove = usb_serial_device_remove, - .drv_attrs = drv_attrs, + .drv_groups = usb_serial_drv_groups, }; int usb_serial_bus_register(struct usb_serial_driver *driver) diff --git a/drivers/usb/serial/ch341.c b/drivers/usb/serial/ch341.c index d255f66e708..2d72aa3564a 100644 --- a/drivers/usb/serial/ch341.c +++ b/drivers/usb/serial/ch341.c @@ -16,7 +16,6 @@ */ #include <linux/kernel.h> -#include <linux/init.h> #include <linux/tty.h> #include <linux/module.h> #include <linux/slab.h> @@ -80,11 +79,9 @@ MODULE_DEVICE_TABLE(usb, id_table); struct ch341_private { spinlock_t lock; /* access lock */ - wait_queue_head_t delta_msr_wait; /* wait queue for modem status */ unsigned baud_rate; /* set baud rate */ u8 line_control; /* set line control value RTS/DTR */ u8 line_status; /* active status of modem control inputs */ - u8 multi_status_change; /* status changed multiple since last call */ }; static int ch341_control_out(struct usb_device *dev, u8 request, @@ -175,7 +172,6 @@ static int ch341_get_status(struct usb_device *dev, struct ch341_private *priv) r = 0; spin_lock_irqsave(&priv->lock, flags); priv->line_status = (~(*buffer)) & CH341_BITS_MODEM_STAT; - priv->multi_status_change = 0; spin_unlock_irqrestore(&priv->lock, flags); } else r = -EPROTO; @@ -252,7 +248,6 @@ static int ch341_port_probe(struct usb_serial_port *port) return -ENOMEM; spin_lock_init(&priv->lock); - init_waitqueue_head(&priv->delta_msr_wait); priv->baud_rate = DEFAULT_BAUD_RATE; priv->line_control = CH341_BIT_RTS | CH341_BIT_DTR; @@ -298,7 +293,6 @@ static void ch341_dtr_rts(struct usb_serial_port *port, int on) priv->line_control &= ~(CH341_BIT_RTS | CH341_BIT_DTR); spin_unlock_irqrestore(&priv->lock, flags); ch341_set_handshake(port->serial->dev, priv->line_control); - wake_up_interruptible(&priv->delta_msr_wait); } static void ch341_close(struct usb_serial_port *port) @@ -329,11 +323,11 @@ static int ch341_open(struct tty_struct *tty, struct usb_serial_port *port) if (r) goto out; - dev_dbg(&port->dev, "%s - submitting interrupt urb", __func__); + dev_dbg(&port->dev, "%s - submitting interrupt urb\n", __func__); r = usb_submit_urb(port->interrupt_in_urb, GFP_KERNEL); if (r) { - dev_err(&port->dev, "%s - failed submitting interrupt urb," - " error %d\n", __func__, r); + dev_err(&port->dev, "%s - failed to submit interrupt urb: %d\n", + __func__, r); ch341_close(port); goto out; } @@ -387,10 +381,8 @@ static void ch341_break_ctl(struct tty_struct *tty, int break_state) uint8_t *break_reg; break_reg = kmalloc(2, GFP_KERNEL); - if (!break_reg) { - dev_err(&port->dev, "%s - kmalloc failed\n", __func__); + if (!break_reg) return; - } r = ch341_control_in(port->serial->dev, CH341_REQ_READ_REG, ch341_break_reg, 0, break_reg, 2); @@ -445,11 +437,55 @@ static int ch341_tiocmset(struct tty_struct *tty, return ch341_set_handshake(port->serial->dev, control); } +static void ch341_update_line_status(struct usb_serial_port *port, + unsigned char *data, size_t len) +{ + struct ch341_private *priv = usb_get_serial_port_data(port); + struct tty_struct *tty; + unsigned long flags; + u8 status; + u8 delta; + + if (len < 4) + return; + + status = ~data[2] & CH341_BITS_MODEM_STAT; + + spin_lock_irqsave(&priv->lock, flags); + delta = status ^ priv->line_status; + priv->line_status = status; + spin_unlock_irqrestore(&priv->lock, flags); + + if (data[1] & CH341_MULT_STAT) + dev_dbg(&port->dev, "%s - multiple status change\n", __func__); + + if (!delta) + return; + + if (delta & CH341_BIT_CTS) + port->icount.cts++; + if (delta & CH341_BIT_DSR) + port->icount.dsr++; + if (delta & CH341_BIT_RI) + port->icount.rng++; + if (delta & CH341_BIT_DCD) { + port->icount.dcd++; + tty = tty_port_tty_get(&port->port); + if (tty) { + usb_serial_handle_dcd_change(port, tty, + status & CH341_BIT_DCD); + tty_kref_put(tty); + } + } + + wake_up_interruptible(&port->port.delta_msr_wait); +} + static void ch341_read_int_callback(struct urb *urb) { - struct usb_serial_port *port = (struct usb_serial_port *) urb->context; + struct usb_serial_port *port = urb->context; unsigned char *data = urb->transfer_buffer; - unsigned int actual_length = urb->actual_length; + unsigned int len = urb->actual_length; int status; switch (urb->status) { @@ -460,105 +496,23 @@ static void ch341_read_int_callback(struct urb *urb) case -ENOENT: case -ESHUTDOWN: /* this urb is terminated, clean up */ - dev_dbg(&urb->dev->dev, "%s - urb shutting down with status: %d\n", + dev_dbg(&urb->dev->dev, "%s - urb shutting down: %d\n", __func__, urb->status); return; default: - dev_dbg(&urb->dev->dev, "%s - nonzero urb status received: %d\n", + dev_dbg(&urb->dev->dev, "%s - nonzero urb status: %d\n", __func__, urb->status); goto exit; } - usb_serial_debug_data(&port->dev, __func__, - urb->actual_length, urb->transfer_buffer); - - if (actual_length >= 4) { - struct ch341_private *priv = usb_get_serial_port_data(port); - unsigned long flags; - u8 prev_line_status = priv->line_status; - - spin_lock_irqsave(&priv->lock, flags); - priv->line_status = (~(data[2])) & CH341_BITS_MODEM_STAT; - if ((data[1] & CH341_MULT_STAT)) - priv->multi_status_change = 1; - spin_unlock_irqrestore(&priv->lock, flags); - - if ((priv->line_status ^ prev_line_status) & CH341_BIT_DCD) { - struct tty_struct *tty = tty_port_tty_get(&port->port); - if (tty) - usb_serial_handle_dcd_change(port, tty, - priv->line_status & CH341_BIT_DCD); - tty_kref_put(tty); - } - - wake_up_interruptible(&priv->delta_msr_wait); - } - + usb_serial_debug_data(&port->dev, __func__, len, data); + ch341_update_line_status(port, data, len); exit: status = usb_submit_urb(urb, GFP_ATOMIC); - if (status) - dev_err(&urb->dev->dev, - "%s - usb_submit_urb failed with result %d\n", + if (status) { + dev_err(&urb->dev->dev, "%s - usb_submit_urb failed: %d\n", __func__, status); -} - -static int wait_modem_info(struct usb_serial_port *port, unsigned int arg) -{ - struct ch341_private *priv = usb_get_serial_port_data(port); - unsigned long flags; - u8 prevstatus; - u8 status; - u8 changed; - u8 multi_change = 0; - - spin_lock_irqsave(&priv->lock, flags); - prevstatus = priv->line_status; - priv->multi_status_change = 0; - spin_unlock_irqrestore(&priv->lock, flags); - - while (!multi_change) { - interruptible_sleep_on(&priv->delta_msr_wait); - /* see if a signal did it */ - if (signal_pending(current)) - return -ERESTARTSYS; - - spin_lock_irqsave(&priv->lock, flags); - status = priv->line_status; - multi_change = priv->multi_status_change; - spin_unlock_irqrestore(&priv->lock, flags); - - changed = prevstatus ^ status; - - if (((arg & TIOCM_RNG) && (changed & CH341_BIT_RI)) || - ((arg & TIOCM_DSR) && (changed & CH341_BIT_DSR)) || - ((arg & TIOCM_CD) && (changed & CH341_BIT_DCD)) || - ((arg & TIOCM_CTS) && (changed & CH341_BIT_CTS))) { - return 0; - } - prevstatus = status; } - - return 0; -} - -static int ch341_ioctl(struct tty_struct *tty, - unsigned int cmd, unsigned long arg) -{ - struct usb_serial_port *port = tty->driver_data; - - dev_dbg(&port->dev, "%s (%d) cmd = 0x%04x\n", __func__, port->number, cmd); - - switch (cmd) { - case TIOCMIWAIT: - dev_dbg(&port->dev, "%s (%d) TIOCMIWAIT\n", __func__, port->number); - return wait_modem_info(port, arg); - - default: - dev_dbg(&port->dev, "%s not supported = 0x%04x\n", __func__, cmd); - break; - } - - return -ENOIOCTLCMD; } static int ch341_tiocmget(struct tty_struct *tty) @@ -610,11 +564,11 @@ static struct usb_serial_driver ch341_device = { .dtr_rts = ch341_dtr_rts, .carrier_raised = ch341_carrier_raised, .close = ch341_close, - .ioctl = ch341_ioctl, .set_termios = ch341_set_termios, .break_ctl = ch341_break_ctl, .tiocmget = ch341_tiocmget, .tiocmset = ch341_tiocmset, + .tiocmiwait = usb_serial_generic_tiocmiwait, .read_int_callback = ch341_read_int_callback, .port_probe = ch341_port_probe, .port_remove = ch341_port_remove, diff --git a/drivers/usb/serial/console.c b/drivers/usb/serial/console.c index 5f3bcd31e20..8d7fc48b1f3 100644 --- a/drivers/usb/serial/console.c +++ b/drivers/usb/serial/console.c @@ -14,7 +14,6 @@ #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt #include <linux/kernel.h> -#include <linux/init.h> #include <linux/slab.h> #include <linux/tty.h> #include <linux/console.h> @@ -108,18 +107,18 @@ static int usb_console_setup(struct console *co, char *options) * no need to check the index here: if the index is wrong, console * code won't call us */ - serial = usb_serial_get_by_index(co->index); - if (serial == NULL) { + port = usb_serial_port_get_by_minor(co->index); + if (port == NULL) { /* no device is connected yet, sorry :( */ pr_err("No USB device connected to ttyUSB%i\n", co->index); return -ENODEV; } + serial = port->serial; retval = usb_autopm_get_interface(serial->interface); if (retval) goto error_get_interface; - port = serial->port[co->index - serial->minor]; tty_port_tty_set(&port->port, NULL); info->port = port; @@ -135,7 +134,6 @@ static int usb_console_setup(struct console *co, char *options) tty = kzalloc(sizeof(*tty), GFP_KERNEL); if (!tty) { retval = -ENOMEM; - dev_err(&port->dev, "no more memory\n"); goto reset_open_count; } kref_init(&tty->kref); @@ -144,18 +142,13 @@ static int usb_console_setup(struct console *co, char *options) tty->index = co->index; if (tty_init_termios(tty)) { retval = -ENOMEM; - dev_err(&port->dev, "no more memory\n"); goto free_tty; } } /* only call the device specific open if this * is the first time the port is opened */ - if (serial->type->open) - retval = serial->type->open(NULL, port); - else - retval = usb_serial_generic_open(NULL, port); - + retval = serial->type->open(NULL, port); if (retval) { dev_err(&port->dev, "could not open USB console port\n"); goto fail; @@ -210,10 +203,10 @@ static void usb_console_write(struct console *co, if (count == 0) return; - pr_debug("%s - port %d, %d byte(s)\n", __func__, port->number, count); + dev_dbg(&port->dev, "%s - %d byte(s)\n", __func__, count); if (!port->port.console) { - pr_debug("%s - port not opened\n", __func__); + dev_dbg(&port->dev, "%s - port not opened\n", __func__); return; } @@ -230,21 +223,14 @@ static void usb_console_write(struct console *co, } /* pass on to the driver specific version of this function if it is available */ - if (serial->type->write) - retval = serial->type->write(NULL, port, buf, i); - else - retval = usb_serial_generic_write(NULL, port, buf, i); - pr_debug("%s - return value : %d\n", __func__, retval); + retval = serial->type->write(NULL, port, buf, i); + dev_dbg(&port->dev, "%s - write: %d\n", __func__, retval); if (lf) { /* append CR after LF */ unsigned char cr = 13; - if (serial->type->write) - retval = serial->type->write(NULL, - port, &cr, 1); - else - retval = usb_serial_generic_write(NULL, - port, &cr, 1); - pr_debug("%s - return value : %d\n", __func__, retval); + retval = serial->type->write(NULL, port, &cr, 1); + dev_dbg(&port->dev, "%s - write cr: %d\n", + __func__, retval); } buf += i; count -= i; diff --git a/drivers/usb/serial/cp210x.c b/drivers/usb/serial/cp210x.c index f14736f647f..330df5ce435 100644 --- a/drivers/usb/serial/cp210x.c +++ b/drivers/usb/serial/cp210x.c @@ -53,6 +53,7 @@ static const struct usb_device_id id_table[] = { { USB_DEVICE(0x0489, 0xE000) }, /* Pirelli Broadband S.p.A, DP-L10 SIP/GSM Mobile */ { USB_DEVICE(0x0489, 0xE003) }, /* Pirelli Broadband S.p.A, DP-L10 SIP/GSM Mobile */ { USB_DEVICE(0x0745, 0x1000) }, /* CipherLab USB CCD Barcode Scanner 1000 */ + { USB_DEVICE(0x0846, 0x1100) }, /* NetGear Managed Switch M4100 series, M5300 series, M7100 series */ { USB_DEVICE(0x08e6, 0x5501) }, /* Gemalto Prox-PU/CU contactless smartcard reader */ { USB_DEVICE(0x08FD, 0x000A) }, /* Digianswer A/S , ZigBee/802.15.4 MAC Device */ { USB_DEVICE(0x0BED, 0x1100) }, /* MEI (TM) Cashflow-SC Bill/Voucher Acceptor */ @@ -60,6 +61,7 @@ static const struct usb_device_id id_table[] = { { USB_DEVICE(0x0FCF, 0x1003) }, /* Dynastream ANT development board */ { USB_DEVICE(0x0FCF, 0x1004) }, /* Dynastream ANT2USB */ { USB_DEVICE(0x0FCF, 0x1006) }, /* Dynastream ANT development board */ + { USB_DEVICE(0x0FDE, 0xCA05) }, /* OWL Wireless Electricity Monitor CM-160 */ { USB_DEVICE(0x10A6, 0xAA26) }, /* Knock-off DCU-11 cable */ { USB_DEVICE(0x10AB, 0x10C5) }, /* Siemens MC60 Cable */ { USB_DEVICE(0x10B5, 0xAC70) }, /* Nokia CA-42 USB */ @@ -84,6 +86,7 @@ static const struct usb_device_id id_table[] = { { USB_DEVICE(0x10C4, 0x813F) }, /* Tams Master Easy Control */ { USB_DEVICE(0x10C4, 0x814A) }, /* West Mountain Radio RIGblaster P&P */ { USB_DEVICE(0x10C4, 0x814B) }, /* West Mountain Radio RIGtalk */ + { USB_DEVICE(0x2405, 0x0003) }, /* West Mountain Radio RIGblaster Advantage */ { USB_DEVICE(0x10C4, 0x8156) }, /* B&G H3000 link cable */ { USB_DEVICE(0x10C4, 0x815E) }, /* Helicomm IP-Link 1220-DVM */ { USB_DEVICE(0x10C4, 0x815F) }, /* Timewave HamLinkUSB */ @@ -101,6 +104,7 @@ static const struct usb_device_id id_table[] = { { USB_DEVICE(0x10C4, 0x8218) }, /* Lipowsky Industrie Elektronik GmbH, HARP-1 */ { USB_DEVICE(0x10C4, 0x822B) }, /* Modem EDGE(GSM) Comander 2 */ { USB_DEVICE(0x10C4, 0x826B) }, /* Cygnal Integrated Products, Inc., Fasttrax GPS demonstration module */ + { USB_DEVICE(0x10C4, 0x8281) }, /* Nanotec Plug & Drive */ { USB_DEVICE(0x10C4, 0x8293) }, /* Telegesis ETRX2USB */ { USB_DEVICE(0x10C4, 0x82F9) }, /* Procyon AVS */ { USB_DEVICE(0x10C4, 0x8341) }, /* Siemens MC35PU GPRS Modem */ @@ -116,6 +120,8 @@ static const struct usb_device_id id_table[] = { { USB_DEVICE(0x10C4, 0x85F8) }, /* Virtenio Preon32 */ { USB_DEVICE(0x10C4, 0x8664) }, /* AC-Services CAN-IF */ { USB_DEVICE(0x10C4, 0x8665) }, /* AC-Services OBD-IF */ + { USB_DEVICE(0x10C4, 0x88A4) }, /* MMB Networks ZigBee USB Device */ + { USB_DEVICE(0x10C4, 0x88A5) }, /* Planet Innovation Ingeni ZigBee USB Device */ { USB_DEVICE(0x10C4, 0xEA60) }, /* Silicon Labs factory default */ { USB_DEVICE(0x10C4, 0xEA61) }, /* Silicon Labs factory default */ { USB_DEVICE(0x10C4, 0xEA70) }, /* Silicon Labs factory default */ @@ -146,9 +152,30 @@ static const struct usb_device_id id_table[] = { { USB_DEVICE(0x17F4, 0xAAAA) }, /* Wavesense Jazz blood glucose meter */ { USB_DEVICE(0x1843, 0x0200) }, /* Vaisala USB Instrument Cable */ { USB_DEVICE(0x18EF, 0xE00F) }, /* ELV USB-I2C-Interface */ + { USB_DEVICE(0x1ADB, 0x0001) }, /* Schweitzer Engineering C662 Cable */ + { USB_DEVICE(0x1B1C, 0x1C00) }, /* Corsair USB Dongle */ { USB_DEVICE(0x1BE3, 0x07A6) }, /* WAGO 750-923 USB Service Cable */ { USB_DEVICE(0x1E29, 0x0102) }, /* Festo CPX-USB */ { USB_DEVICE(0x1E29, 0x0501) }, /* Festo CMSP */ + { USB_DEVICE(0x1FB9, 0x0100) }, /* Lake Shore Model 121 Current Source */ + { USB_DEVICE(0x1FB9, 0x0200) }, /* Lake Shore Model 218A Temperature Monitor */ + { USB_DEVICE(0x1FB9, 0x0201) }, /* Lake Shore Model 219 Temperature Monitor */ + { USB_DEVICE(0x1FB9, 0x0202) }, /* Lake Shore Model 233 Temperature Transmitter */ + { USB_DEVICE(0x1FB9, 0x0203) }, /* Lake Shore Model 235 Temperature Transmitter */ + { USB_DEVICE(0x1FB9, 0x0300) }, /* Lake Shore Model 335 Temperature Controller */ + { USB_DEVICE(0x1FB9, 0x0301) }, /* Lake Shore Model 336 Temperature Controller */ + { USB_DEVICE(0x1FB9, 0x0302) }, /* Lake Shore Model 350 Temperature Controller */ + { USB_DEVICE(0x1FB9, 0x0303) }, /* Lake Shore Model 371 AC Bridge */ + { USB_DEVICE(0x1FB9, 0x0400) }, /* Lake Shore Model 411 Handheld Gaussmeter */ + { USB_DEVICE(0x1FB9, 0x0401) }, /* Lake Shore Model 425 Gaussmeter */ + { USB_DEVICE(0x1FB9, 0x0402) }, /* Lake Shore Model 455A Gaussmeter */ + { USB_DEVICE(0x1FB9, 0x0403) }, /* Lake Shore Model 475A Gaussmeter */ + { USB_DEVICE(0x1FB9, 0x0404) }, /* Lake Shore Model 465 Three Axis Gaussmeter */ + { USB_DEVICE(0x1FB9, 0x0600) }, /* Lake Shore Model 625A Superconducting MPS */ + { USB_DEVICE(0x1FB9, 0x0601) }, /* Lake Shore Model 642A Magnet Power Supply */ + { USB_DEVICE(0x1FB9, 0x0602) }, /* Lake Shore Model 648 Magnet Power Supply */ + { USB_DEVICE(0x1FB9, 0x0700) }, /* Lake Shore Model 737 VSM Controller */ + { USB_DEVICE(0x1FB9, 0x0701) }, /* Lake Shore Model 776 Hall Matrix */ { USB_DEVICE(0x3195, 0xF190) }, /* Link Instruments MSO-19 */ { USB_DEVICE(0x3195, 0xF280) }, /* Link Instruments MSO-28 */ { USB_DEVICE(0x3195, 0xF281) }, /* Link Instruments MSO-28 */ @@ -280,10 +307,8 @@ static int cp210x_get_config(struct usb_serial_port *port, u8 request, length = (((size - 1) | 3) + 1) / 4; buf = kcalloc(length, sizeof(__le32), GFP_KERNEL); - if (!buf) { - dev_err(&port->dev, "%s - out of memory.\n", __func__); + if (!buf) return -ENOMEM; - } /* Issue the request, attempting to read 'size' bytes */ result = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0), @@ -327,10 +352,8 @@ static int cp210x_set_config(struct usb_serial_port *port, u8 request, length = (((size - 1) | 3) + 1) / 4; buf = kmalloc(length * sizeof(__le32), GFP_KERNEL); - if (!buf) { - dev_err(&port->dev, "%s - out of memory.\n", __func__); + if (!buf) return -ENOMEM; - } /* Array of integers into bytes */ for (i = 0; i < length; i++) @@ -441,11 +464,7 @@ static int cp210x_open(struct tty_struct *tty, struct usb_serial_port *port) static void cp210x_close(struct usb_serial_port *port) { usb_serial_generic_close(port); - - mutex_lock(&port->serial->disc_mutex); - if (!port->serial->disconnected) - cp210x_set_config_single(port, CP210X_IFC_ENABLE, UART_DISABLE); - mutex_unlock(&port->serial->disc_mutex); + cp210x_set_config_single(port, CP210X_IFC_ENABLE, UART_DISABLE); } /* @@ -649,11 +668,6 @@ static void cp210x_set_termios(struct tty_struct *tty, unsigned int bits; unsigned int modem_ctl[4]; - dev_dbg(dev, "%s - port %d\n", __func__, port->number); - - if (!tty) - return; - cflag = tty->termios.c_cflag; old_cflag = old_termios->c_cflag; diff --git a/drivers/usb/serial/cyberjack.c b/drivers/usb/serial/cyberjack.c index 69a4fa1cee2..2916dea3ede 100644 --- a/drivers/usb/serial/cyberjack.c +++ b/drivers/usb/serial/cyberjack.c @@ -30,7 +30,6 @@ #include <linux/kernel.h> #include <linux/errno.h> -#include <linux/init.h> #include <linux/slab.h> #include <linux/tty.h> #include <linux/tty_driver.h> @@ -51,7 +50,6 @@ #define CYBERJACK_PRODUCT_ID 0x0100 /* Function prototypes */ -static void cyberjack_disconnect(struct usb_serial *serial); static int cyberjack_port_probe(struct usb_serial_port *port); static int cyberjack_port_remove(struct usb_serial_port *port); static int cyberjack_open(struct tty_struct *tty, @@ -79,7 +77,6 @@ static struct usb_serial_driver cyberjack_device = { .description = "Reiner SCT Cyberjack USB card reader", .id_table = id_table, .num_ports = 1, - .disconnect = cyberjack_disconnect, .port_probe = cyberjack_port_probe, .port_remove = cyberjack_port_remove, .open = cyberjack_open, @@ -130,20 +127,14 @@ static int cyberjack_port_remove(struct usb_serial_port *port) { struct cyberjack_private *priv; + usb_kill_urb(port->interrupt_in_urb); + priv = usb_get_serial_port_data(port); kfree(priv); return 0; } -static void cyberjack_disconnect(struct usb_serial *serial) -{ - int i; - - for (i = 0; i < serial->num_ports; ++i) - usb_kill_urb(serial->port[i]->interrupt_in_urb); -} - static int cyberjack_open(struct tty_struct *tty, struct usb_serial_port *port) { @@ -166,11 +157,8 @@ static int cyberjack_open(struct tty_struct *tty, static void cyberjack_close(struct usb_serial_port *port) { - if (port->serial->dev) { - /* shutdown any bulk reads that might be going on */ - usb_kill_urb(port->write_urb); - usb_kill_urb(port->read_urb); - } + usb_kill_urb(port->write_urb); + usb_kill_urb(port->read_urb); } static int cyberjack_write(struct tty_struct *tty, @@ -232,7 +220,7 @@ static int cyberjack_write(struct tty_struct *tty, result = usb_submit_urb(port->write_urb, GFP_ATOMIC); if (result) { dev_err(&port->dev, - "%s - failed submitting write urb, error %d", + "%s - failed submitting write urb, error %d\n", __func__, result); /* Throw away data. No better idea what to do with it. */ priv->wrfilled = 0; @@ -290,13 +278,13 @@ static void cyberjack_read_int_callback(struct urb *urb) old_rdtodo = priv->rdtodo; - if (old_rdtodo + size < old_rdtodo) { + if (old_rdtodo > SHRT_MAX - size) { dev_dbg(dev, "To many bulk_in urbs to do.\n"); spin_unlock(&priv->lock); goto resubmit; } - /* "+=" is probably more fault tollerant than "=" */ + /* "+=" is probably more fault tolerant than "=" */ priv->rdtodo += size; dev_dbg(dev, "%s - rdtodo: %d\n", __func__, priv->rdtodo); @@ -324,7 +312,6 @@ static void cyberjack_read_bulk_callback(struct urb *urb) struct usb_serial_port *port = urb->context; struct cyberjack_private *priv = usb_get_serial_port_data(port); struct device *dev = &port->dev; - struct tty_struct *tty; unsigned char *data = urb->transfer_buffer; short todo; int result; @@ -337,16 +324,10 @@ static void cyberjack_read_bulk_callback(struct urb *urb) return; } - tty = tty_port_tty_get(&port->port); - if (!tty) { - dev_dbg(dev, "%s - ignoring since device not open\n", __func__); - return; - } if (urb->actual_length) { - tty_insert_flip_string(tty, data, urb->actual_length); - tty_flip_buffer_push(tty); + tty_insert_flip_string(&port->port, data, urb->actual_length); + tty_flip_buffer_push(&port->port); } - tty_kref_put(tty); spin_lock(&priv->lock); diff --git a/drivers/usb/serial/cypress_m8.c b/drivers/usb/serial/cypress_m8.c index fd8c35fd452..01bf5339281 100644 --- a/drivers/usb/serial/cypress_m8.c +++ b/drivers/usb/serial/cypress_m8.c @@ -27,7 +27,6 @@ #include <linux/kernel.h> #include <linux/errno.h> -#include <linux/init.h> #include <linux/slab.h> #include <linux/tty.h> #include <linux/tty_driver.h> @@ -65,6 +64,7 @@ static const struct usb_device_id id_table_earthmate[] = { static const struct usb_device_id id_table_cyphidcomrs232[] = { { USB_DEVICE(VENDOR_ID_CYPRESS, PRODUCT_ID_CYPHIDCOM) }, { USB_DEVICE(VENDOR_ID_POWERCOM, PRODUCT_ID_UPS) }, + { USB_DEVICE(VENDOR_ID_FRWD, PRODUCT_ID_CYPHIDCOM_FRWD) }, { } /* Terminating entry */ }; @@ -78,6 +78,7 @@ static const struct usb_device_id id_table_combined[] = { { USB_DEVICE(VENDOR_ID_DELORME, PRODUCT_ID_EARTHMATEUSB_LT20) }, { USB_DEVICE(VENDOR_ID_CYPRESS, PRODUCT_ID_CYPHIDCOM) }, { USB_DEVICE(VENDOR_ID_POWERCOM, PRODUCT_ID_UPS) }, + { USB_DEVICE(VENDOR_ID_FRWD, PRODUCT_ID_CYPHIDCOM_FRWD) }, { USB_DEVICE(VENDOR_ID_DAZZLE, PRODUCT_ID_CA42) }, { } /* Terminating entry */ }; @@ -111,8 +112,7 @@ struct cypress_private { int baud_rate; /* stores current baud rate in integer form */ int isthrottled; /* if throttled, discard reads */ - wait_queue_head_t delta_msr_wait; /* used for TIOCMIWAIT */ - char prev_status, diff_status; /* used for TIOCMIWAIT */ + char prev_status; /* used for TIOCMIWAIT */ /* we pass a pointer to this as the argument sent to cypress_set_termios old_termios */ struct ktermios tmp_termios; /* stores the old termios settings */ @@ -130,8 +130,6 @@ static int cypress_write(struct tty_struct *tty, struct usb_serial_port *port, const unsigned char *buf, int count); static void cypress_send(struct usb_serial_port *port); static int cypress_write_room(struct tty_struct *tty); -static int cypress_ioctl(struct tty_struct *tty, - unsigned int cmd, unsigned long arg); static void cypress_set_termios(struct tty_struct *tty, struct usb_serial_port *port, struct ktermios *old); static int cypress_tiocmget(struct tty_struct *tty); @@ -159,10 +157,10 @@ static struct usb_serial_driver cypress_earthmate_device = { .dtr_rts = cypress_dtr_rts, .write = cypress_write, .write_room = cypress_write_room, - .ioctl = cypress_ioctl, .set_termios = cypress_set_termios, .tiocmget = cypress_tiocmget, .tiocmset = cypress_tiocmset, + .tiocmiwait = usb_serial_generic_tiocmiwait, .chars_in_buffer = cypress_chars_in_buffer, .throttle = cypress_throttle, .unthrottle = cypress_unthrottle, @@ -185,10 +183,10 @@ static struct usb_serial_driver cypress_hidcom_device = { .dtr_rts = cypress_dtr_rts, .write = cypress_write, .write_room = cypress_write_room, - .ioctl = cypress_ioctl, .set_termios = cypress_set_termios, .tiocmget = cypress_tiocmget, .tiocmset = cypress_tiocmset, + .tiocmiwait = usb_serial_generic_tiocmiwait, .chars_in_buffer = cypress_chars_in_buffer, .throttle = cypress_throttle, .unthrottle = cypress_unthrottle, @@ -211,10 +209,10 @@ static struct usb_serial_driver cypress_ca42v2_device = { .dtr_rts = cypress_dtr_rts, .write = cypress_write, .write_room = cypress_write_room, - .ioctl = cypress_ioctl, .set_termios = cypress_set_termios, .tiocmget = cypress_tiocmget, .tiocmset = cypress_tiocmset, + .tiocmiwait = usb_serial_generic_tiocmiwait, .chars_in_buffer = cypress_chars_in_buffer, .throttle = cypress_throttle, .unthrottle = cypress_unthrottle, @@ -231,6 +229,12 @@ static struct usb_serial_driver * const serial_drivers[] = { * Cypress serial helper functions *****************************************************************************/ +/* FRWD Dongle hidcom needs to skip reset and speed checks */ +static inline bool is_frwd(struct usb_device *dev) +{ + return ((le16_to_cpu(dev->descriptor.idVendor) == VENDOR_ID_FRWD) && + (le16_to_cpu(dev->descriptor.idProduct) == PRODUCT_ID_CYPHIDCOM_FRWD)); +} static int analyze_baud_rate(struct usb_serial_port *port, speed_t new_rate) { @@ -240,6 +244,10 @@ static int analyze_baud_rate(struct usb_serial_port *port, speed_t new_rate) if (unstable_bauds) return new_rate; + /* FRWD Dongle uses 115200 bps */ + if (is_frwd(port->serial->dev)) + return new_rate; + /* * The general purpose firmware for the Cypress M8 allows for * a maximum speed of 57600bps (I have no idea whether DeLorme @@ -271,7 +279,7 @@ static int analyze_baud_rate(struct usb_serial_port *port, speed_t new_rate) * the generic firmware, but are not used with * NMEA and SiRF protocols */ dev_dbg(&port->dev, - "%s - failed setting baud rate, unsupported speed of %d on Earthmate GPS", + "%s - failed setting baud rate, unsupported speed of %d on Earthmate GPS\n", __func__, new_rate); return -1; } @@ -425,7 +433,7 @@ static void cypress_set_dead(struct usb_serial_port *port) spin_unlock_irqrestore(&priv->lock, flags); dev_err(&port->dev, "cypress_m8 suspending failing port %d - " - "interval might be too short\n", port->number); + "interval might be too short\n", port->port_number); } @@ -449,9 +457,12 @@ static int cypress_generic_port_probe(struct usb_serial_port *port) kfree(priv); return -ENOMEM; } - init_waitqueue_head(&priv->delta_msr_wait); - usb_reset_configuration(serial->dev); + /* Skip reset for FRWD device. It is a workaound: + device hangs if it receives SET_CONFIGURE in Configured + state. */ + if (!is_frwd(serial->dev)) + usb_reset_configuration(serial->dev); priv->cmd_ctrl = 0; priv->line_control = 0; @@ -482,6 +493,8 @@ static int cypress_generic_port_probe(struct usb_serial_port *port) } usb_set_serial_port_data(port, priv); + port->port.drain_delay = 256; + return 0; } @@ -612,7 +625,7 @@ static int cypress_open(struct tty_struct *tty, struct usb_serial_port *port) __func__, result); cypress_set_dead(port); } - port->port.drain_delay = 256; + return result; } /* cypress_open */ @@ -635,12 +648,6 @@ static void cypress_close(struct usb_serial_port *port) struct cypress_private *priv = usb_get_serial_port_data(port); unsigned long flags; - /* writing is potentially harmful, lock must be taken */ - mutex_lock(&port->serial->disc_mutex); - if (port->serial->disconnected) { - mutex_unlock(&port->serial->disc_mutex); - return; - } spin_lock_irqsave(&priv->lock, flags); kfifo_reset_out(&priv->write_fifo); spin_unlock_irqrestore(&priv->lock, flags); @@ -652,7 +659,6 @@ static void cypress_close(struct usb_serial_port *port) if (stats) dev_info(&port->dev, "Statistics: %d Bytes In | %d Bytes Out | %d Commands Issued\n", priv->bytes_in, priv->bytes_out, priv->cmd_count); - mutex_unlock(&port->serial->disc_mutex); } /* cypress_close */ @@ -661,7 +667,7 @@ static int cypress_write(struct tty_struct *tty, struct usb_serial_port *port, { struct cypress_private *priv = usb_get_serial_port_data(port); - dev_dbg(&port->dev, "%s - port %d, %d bytes\n", __func__, port->number, count); + dev_dbg(&port->dev, "%s - %d bytes\n", __func__, count); /* line control commands, which need to be executed immediately, are not put into the buffer for obvious reasons. @@ -856,53 +862,6 @@ static int cypress_tiocmset(struct tty_struct *tty, return cypress_write(tty, port, NULL, 0); } - -static int cypress_ioctl(struct tty_struct *tty, - unsigned int cmd, unsigned long arg) -{ - struct usb_serial_port *port = tty->driver_data; - struct cypress_private *priv = usb_get_serial_port_data(port); - - dev_dbg(&port->dev, "%s - port %d, cmd 0x%.4x\n", __func__, port->number, cmd); - - switch (cmd) { - /* This code comes from drivers/char/serial.c and ftdi_sio.c */ - case TIOCMIWAIT: - while (priv != NULL) { - interruptible_sleep_on(&priv->delta_msr_wait); - /* see if a signal did it */ - if (signal_pending(current)) - return -ERESTARTSYS; - else { - char diff = priv->diff_status; - if (diff == 0) - return -EIO; /* no change => error */ - - /* consume all events */ - priv->diff_status = 0; - - /* return 0 if caller wanted to know about - these bits */ - if (((arg & TIOCM_RNG) && (diff & UART_RI)) || - ((arg & TIOCM_DSR) && (diff & UART_DSR)) || - ((arg & TIOCM_CD) && (diff & UART_CD)) || - ((arg & TIOCM_CTS) && (diff & UART_CTS))) - return 0; - /* otherwise caller can't care less about what - * happened, and so we continue to wait for - * more events. - */ - } - } - return 0; - default: - break; - } - dev_dbg(&port->dev, "%s - arg not supported - it was 0x%04x - check include/asm/ioctls.h\n", __func__, cmd); - return -ENOIOCTLCMD; -} /* cypress_ioctl */ - - static void cypress_set_termios(struct tty_struct *tty, struct usb_serial_port *port, struct ktermios *old_termios) { @@ -1185,9 +1144,21 @@ static void cypress_read_int_callback(struct urb *urb) spin_lock_irqsave(&priv->lock, flags); /* check to see if status has changed */ if (priv->current_status != priv->prev_status) { - priv->diff_status |= priv->current_status ^ - priv->prev_status; - wake_up_interruptible(&priv->delta_msr_wait); + u8 delta = priv->current_status ^ priv->prev_status; + + if (delta & UART_MSR_MASK) { + if (delta & UART_CTS) + port->icount.cts++; + if (delta & UART_DSR) + port->icount.dsr++; + if (delta & UART_RI) + port->icount.rng++; + if (delta & UART_CD) + port->icount.dcd++; + + wake_up_interruptible(&port->port.delta_msr_wait); + } + priv->prev_status = priv->current_status; } spin_unlock_irqrestore(&priv->lock, flags); @@ -1214,10 +1185,10 @@ static void cypress_read_int_callback(struct urb *urb) spin_unlock_irqrestore(&priv->lock, flags); /* process read if there is data other than line status */ - if (tty && bytes > i) { - tty_insert_flip_string_fixed_flag(tty, data + i, + if (bytes > i) { + tty_insert_flip_string_fixed_flag(&port->port, data + i, tty_flag, bytes - i); - tty_flip_buffer_push(tty); + tty_flip_buffer_push(&port->port); } spin_lock_irqsave(&priv->lock, flags); @@ -1253,7 +1224,6 @@ static void cypress_write_int_callback(struct urb *urb) struct usb_serial_port *port = urb->context; struct cypress_private *priv = usb_get_serial_port_data(port); struct device *dev = &urb->dev->dev; - int result; int status = urb->status; switch (status) { @@ -1268,21 +1238,9 @@ static void cypress_write_int_callback(struct urb *urb) __func__, status); priv->write_urb_in_use = 0; return; - case -EPIPE: /* no break needed; clear halt and resubmit */ - if (!priv->comm_is_ok) - break; - usb_clear_halt(port->serial->dev, 0x02); - /* error in the urb, so we have to resubmit it */ - dev_dbg(dev, "%s - nonzero write bulk status received: %d\n", - __func__, status); - port->interrupt_out_urb->transfer_buffer_length = 1; - result = usb_submit_urb(port->interrupt_out_urb, GFP_ATOMIC); - if (!result) - return; - dev_err(dev, "%s - failed resubmitting write urb, error %d\n", - __func__, result); - cypress_set_dead(port); - break; + case -EPIPE: + /* Cannot call usb_clear_halt while in_interrupt */ + /* FALLTHROUGH */ default: dev_err(dev, "%s - unexpected nonzero write status received: %d\n", __func__, status); diff --git a/drivers/usb/serial/cypress_m8.h b/drivers/usb/serial/cypress_m8.h index 67cf6082688..119d2e17077 100644 --- a/drivers/usb/serial/cypress_m8.h +++ b/drivers/usb/serial/cypress_m8.h @@ -24,6 +24,10 @@ #define VENDOR_ID_CYPRESS 0x04b4 #define PRODUCT_ID_CYPHIDCOM 0x5500 +/* FRWD Dongle - a GPS sports watch */ +#define VENDOR_ID_FRWD 0x6737 +#define PRODUCT_ID_CYPHIDCOM_FRWD 0x0001 + /* Powercom UPS, chip CY7C63723 */ #define VENDOR_ID_POWERCOM 0x0d9f #define PRODUCT_ID_UPS 0x0002 @@ -51,19 +55,23 @@ #define CT_GENERIC 0x0F /* End of chiptype definitions */ -/* RS-232 serial data communication protocol definitions */ -/* these are sent / read at byte 0 of the input/output hid reports */ -/* You can find these values defined in the CY4601 USB to Serial design notes */ - -#define CONTROL_DTR 0x20 /* data terminal ready - flow control - host to device */ -#define UART_DSR 0x20 /* data set ready - flow control - device to host */ -#define CONTROL_RTS 0x10 /* request to send - flow control - host to device */ -#define UART_CTS 0x10 /* clear to send - flow control - device to host */ -#define UART_RI 0x10 /* ring indicator - modem - device to host */ -#define UART_CD 0x40 /* carrier detect - modem - device to host */ -#define CYP_ERROR 0x08 /* received from input report - device to host */ -/* Note - the below has nothing to do with the "feature report" reset */ -#define CONTROL_RESET 0x08 /* sent with output report - host to device */ +/* + * RS-232 serial data communication protocol definitions. + * + * These are sent / read at byte 0 of the input/output hid reports. + * You can find these values defined in the CY4601 USB to Serial design notes. + */ + +#define CONTROL_DTR 0x20 /* data terminal ready */ +#define CONTROL_RTS 0x10 /* request to send */ +#define CONTROL_RESET 0x08 /* sent with output report */ + +#define UART_MSR_MASK 0xf0 +#define UART_RI 0x80 /* ring indicator */ +#define UART_CD 0x40 /* carrier detect */ +#define UART_DSR 0x20 /* data set ready */ +#define UART_CTS 0x10 /* clear to send */ +#define CYP_ERROR 0x08 /* received from input report */ /* End of RS-232 protocol definitions */ diff --git a/drivers/usb/serial/digi_acceleport.c b/drivers/usb/serial/digi_acceleport.c index 45d4af62967..8a23c53b946 100644 --- a/drivers/usb/serial/digi_acceleport.c +++ b/drivers/usb/serial/digi_acceleport.c @@ -17,7 +17,6 @@ #include <linux/kernel.h> #include <linux/errno.h> -#include <linux/init.h> #include <linux/slab.h> #include <linux/tty.h> #include <linux/tty_driver.h> @@ -196,7 +195,6 @@ struct digi_port { unsigned char dp_out_buf[DIGI_OUT_BUF_SIZE]; int dp_write_urb_in_use; unsigned int dp_modem_signals; - wait_queue_head_t dp_modem_change_wait; int dp_transmit_idle; wait_queue_head_t dp_transmit_idle_wait; int dp_throttled; @@ -210,7 +208,6 @@ struct digi_port { /* Local Function Declarations */ -static void digi_wakeup_write(struct usb_serial_port *port); static void digi_wakeup_write_lock(struct work_struct *work); static int digi_write_oob_command(struct usb_serial_port *port, unsigned char *buf, int count, int interruptible); @@ -374,20 +371,10 @@ static void digi_wakeup_write_lock(struct work_struct *work) unsigned long flags; spin_lock_irqsave(&priv->dp_port_lock, flags); - digi_wakeup_write(port); + tty_port_tty_wakeup(&port->port); spin_unlock_irqrestore(&priv->dp_port_lock, flags); } -static void digi_wakeup_write(struct usb_serial_port *port) -{ - struct tty_struct *tty = tty_port_tty_get(&port->port); - if (tty) { - tty_wakeup(tty); - tty_kref_put(tty); - } -} - - /* * Digi Write OOB Command * @@ -1044,7 +1031,7 @@ static void digi_write_bulk_callback(struct urb *urb) } } /* wake up processes sleeping on writes immediately */ - digi_wakeup_write(port); + tty_port_tty_wakeup(&port->port); /* also queue up a wakeup at scheduler time, in case we */ /* lost the race in write_chan(). */ schedule_work(&priv->dp_wakeup_work); @@ -1149,53 +1136,51 @@ static void digi_close(struct usb_serial_port *port) if (port->serial->disconnected) goto exit; - if (port->serial->dev) { - /* FIXME: Transmit idle belongs in the wait_unti_sent path */ - digi_transmit_idle(port, DIGI_CLOSE_TIMEOUT); - - /* disable input flow control */ - buf[0] = DIGI_CMD_SET_INPUT_FLOW_CONTROL; - buf[1] = priv->dp_port_num; - buf[2] = DIGI_DISABLE; - buf[3] = 0; - - /* disable output flow control */ - buf[4] = DIGI_CMD_SET_OUTPUT_FLOW_CONTROL; - buf[5] = priv->dp_port_num; - buf[6] = DIGI_DISABLE; - buf[7] = 0; - - /* disable reading modem signals automatically */ - buf[8] = DIGI_CMD_READ_INPUT_SIGNALS; - buf[9] = priv->dp_port_num; - buf[10] = DIGI_DISABLE; - buf[11] = 0; - - /* disable receive */ - buf[12] = DIGI_CMD_RECEIVE_ENABLE; - buf[13] = priv->dp_port_num; - buf[14] = DIGI_DISABLE; - buf[15] = 0; - - /* flush fifos */ - buf[16] = DIGI_CMD_IFLUSH_FIFO; - buf[17] = priv->dp_port_num; - buf[18] = DIGI_FLUSH_TX | DIGI_FLUSH_RX; - buf[19] = 0; - - ret = digi_write_oob_command(port, buf, 20, 0); - if (ret != 0) - dev_dbg(&port->dev, "digi_close: write oob failed, ret=%d\n", ret); - - /* wait for final commands on oob port to complete */ - prepare_to_wait(&priv->dp_flush_wait, &wait, - TASK_INTERRUPTIBLE); - schedule_timeout(DIGI_CLOSE_TIMEOUT); - finish_wait(&priv->dp_flush_wait, &wait); - - /* shutdown any outstanding bulk writes */ - usb_kill_urb(port->write_urb); - } + /* FIXME: Transmit idle belongs in the wait_unti_sent path */ + digi_transmit_idle(port, DIGI_CLOSE_TIMEOUT); + + /* disable input flow control */ + buf[0] = DIGI_CMD_SET_INPUT_FLOW_CONTROL; + buf[1] = priv->dp_port_num; + buf[2] = DIGI_DISABLE; + buf[3] = 0; + + /* disable output flow control */ + buf[4] = DIGI_CMD_SET_OUTPUT_FLOW_CONTROL; + buf[5] = priv->dp_port_num; + buf[6] = DIGI_DISABLE; + buf[7] = 0; + + /* disable reading modem signals automatically */ + buf[8] = DIGI_CMD_READ_INPUT_SIGNALS; + buf[9] = priv->dp_port_num; + buf[10] = DIGI_DISABLE; + buf[11] = 0; + + /* disable receive */ + buf[12] = DIGI_CMD_RECEIVE_ENABLE; + buf[13] = priv->dp_port_num; + buf[14] = DIGI_DISABLE; + buf[15] = 0; + + /* flush fifos */ + buf[16] = DIGI_CMD_IFLUSH_FIFO; + buf[17] = priv->dp_port_num; + buf[18] = DIGI_FLUSH_TX | DIGI_FLUSH_RX; + buf[19] = 0; + + ret = digi_write_oob_command(port, buf, 20, 0); + if (ret != 0) + dev_dbg(&port->dev, "digi_close: write oob failed, ret=%d\n", + ret); + /* wait for final commands on oob port to complete */ + prepare_to_wait(&priv->dp_flush_wait, &wait, + TASK_INTERRUPTIBLE); + schedule_timeout(DIGI_CLOSE_TIMEOUT); + finish_wait(&priv->dp_flush_wait, &wait); + + /* shutdown any outstanding bulk writes */ + usb_kill_urb(port->write_urb); exit: spin_lock_irq(&priv->dp_port_lock); priv->dp_write_urb_in_use = 0; @@ -1252,7 +1237,6 @@ static int digi_port_init(struct usb_serial_port *port, unsigned port_num) spin_lock_init(&priv->dp_port_lock); priv->dp_port_num = port_num; - init_waitqueue_head(&priv->dp_modem_change_wait); init_waitqueue_head(&priv->dp_transmit_idle_wait); init_waitqueue_head(&priv->dp_flush_wait); init_waitqueue_head(&priv->dp_close_wait); @@ -1319,11 +1303,7 @@ static void digi_release(struct usb_serial *serial) static int digi_port_probe(struct usb_serial_port *port) { - unsigned port_num; - - port_num = port->number - port->serial->minor; - - return digi_port_init(port, port_num); + return digi_port_init(port, port->port_number); } static int digi_port_remove(struct usb_serial_port *port) @@ -1399,9 +1379,7 @@ static void digi_read_bulk_callback(struct urb *urb) static int digi_read_inb_callback(struct urb *urb) { - struct usb_serial_port *port = urb->context; - struct tty_struct *tty; struct digi_port *priv = usb_get_serial_port_data(port); int opcode = ((unsigned char *)urb->transfer_buffer)[0]; int len = ((unsigned char *)urb->transfer_buffer)[1]; @@ -1425,7 +1403,6 @@ static int digi_read_inb_callback(struct urb *urb) return -1; } - tty = tty_port_tty_get(&port->port); spin_lock(&priv->dp_port_lock); /* check for throttle; if set, do not resubmit read urb */ @@ -1435,13 +1412,13 @@ static int digi_read_inb_callback(struct urb *urb) priv->dp_throttle_restart = 1; /* receive data */ - if (tty && opcode == DIGI_CMD_RECEIVE_DATA) { + if (opcode == DIGI_CMD_RECEIVE_DATA) { /* get flag from port_status */ flag = 0; /* overrun is special, not associated with a char */ if (port_status & DIGI_OVERRUN_ERROR) - tty_insert_flip_char(tty, 0, TTY_OVERRUN); + tty_insert_flip_char(&port->port, 0, TTY_OVERRUN); /* break takes precedence over parity, */ /* which takes precedence over framing errors */ @@ -1455,13 +1432,12 @@ static int digi_read_inb_callback(struct urb *urb) /* data length is len-1 (one byte of len is port_status) */ --len; if (len > 0) { - tty_insert_flip_string_fixed_flag(tty, data, flag, - len); - tty_flip_buffer_push(tty); + tty_insert_flip_string_fixed_flag(&port->port, data, + flag, len); + tty_flip_buffer_push(&port->port); } } spin_unlock(&priv->dp_port_lock); - tty_kref_put(tty); if (opcode == DIGI_CMD_RECEIVE_DISABLE) dev_dbg(&port->dev, "%s: got RECEIVE_DISABLE\n", __func__); @@ -1526,7 +1502,7 @@ static int digi_read_oob_callback(struct urb *urb) /* port must be open to use tty struct */ if (rts) { tty->hw_stopped = 0; - digi_wakeup_write(port); + tty_port_tty_wakeup(&port->port); } } else { priv->dp_modem_signals &= ~TIOCM_CTS; @@ -1547,7 +1523,6 @@ static int digi_read_oob_callback(struct urb *urb) else priv->dp_modem_signals &= ~TIOCM_CD; - wake_up_interruptible(&priv->dp_modem_change_wait); spin_unlock(&priv->dp_port_lock); } else if (opcode == DIGI_CMD_TRANSMIT_IDLE) { spin_lock(&priv->dp_port_lock); diff --git a/drivers/usb/serial/empeg.c b/drivers/usb/serial/empeg.c index 0f658618db1..90e603d5f66 100644 --- a/drivers/usb/serial/empeg.c +++ b/drivers/usb/serial/empeg.c @@ -17,7 +17,6 @@ #include <linux/kernel.h> #include <linux/errno.h> -#include <linux/init.h> #include <linux/slab.h> #include <linux/tty.h> #include <linux/tty_driver.h> diff --git a/drivers/usb/serial/f81232.c b/drivers/usb/serial/f81232.c index 6e4eb57d017..c5dc233db2d 100644 --- a/drivers/usb/serial/f81232.c +++ b/drivers/usb/serial/f81232.c @@ -12,7 +12,6 @@ #include <linux/kernel.h> #include <linux/errno.h> -#include <linux/init.h> #include <linux/slab.h> #include <linux/tty.h> #include <linux/tty_driver.h> @@ -47,7 +46,6 @@ MODULE_DEVICE_TABLE(usb, id_table); struct f81232_private { spinlock_t lock; - wait_queue_head_t delta_msr_wait; u8 line_control; u8 line_status; }; @@ -56,6 +54,13 @@ static void f81232_update_line_status(struct usb_serial_port *port, unsigned char *data, unsigned int actual_length) { + /* + * FIXME: Update port->icount, and call + * + * wake_up_interruptible(&port->port.delta_msr_wait); + * + * on MSR changes. + */ } static void f81232_read_int_callback(struct urb *urb) @@ -100,7 +105,6 @@ static void f81232_process_read_urb(struct urb *urb) { struct usb_serial_port *port = urb->context; struct f81232_private *priv = usb_get_serial_port_data(port); - struct tty_struct *tty; unsigned char *data = urb->transfer_buffer; char tty_flag = TTY_NORMAL; unsigned long flags; @@ -112,15 +116,10 @@ static void f81232_process_read_urb(struct urb *urb) line_status = priv->line_status; priv->line_status &= ~UART_STATE_TRANSIENT_MASK; spin_unlock_irqrestore(&priv->lock, flags); - wake_up_interruptible(&priv->delta_msr_wait); if (!urb->actual_length) return; - tty = tty_port_tty_get(&port->port); - if (!tty) - return; - /* break takes precedence over parity, */ /* which takes precedence over framing errors */ if (line_status & UART_BREAK_ERROR) @@ -133,19 +132,19 @@ static void f81232_process_read_urb(struct urb *urb) /* overrun is special, not associated with a char */ if (line_status & UART_OVERRUN_ERROR) - tty_insert_flip_char(tty, 0, TTY_OVERRUN); + tty_insert_flip_char(&port->port, 0, TTY_OVERRUN); if (port->port.console && port->sysrq) { for (i = 0; i < urb->actual_length; ++i) if (!usb_serial_handle_sysrq_char(port, data[i])) - tty_insert_flip_char(tty, data[i], tty_flag); + tty_insert_flip_char(&port->port, data[i], + tty_flag); } else { - tty_insert_flip_string_fixed_flag(tty, data, tty_flag, + tty_insert_flip_string_fixed_flag(&port->port, data, tty_flag, urb->actual_length); } - tty_flip_buffer_push(tty); - tty_kref_put(tty); + tty_flip_buffer_push(&port->port); } static int set_control_lines(struct usb_device *dev, u8 value) @@ -171,11 +170,12 @@ static void f81232_set_termios(struct tty_struct *tty, /* FIXME - Stubbed out for now */ /* Don't change anything if nothing has changed */ - if (!tty_termios_hw_change(&tty->termios, old_termios)) + if (old_termios && !tty_termios_hw_change(&tty->termios, old_termios)) return; /* Do the real work here... */ - tty_termios_copy_hw(&tty->termios, old_termios); + if (old_termios) + tty_termios_copy_hw(&tty->termios, old_termios); } static int f81232_tiocmget(struct tty_struct *tty) @@ -193,12 +193,11 @@ static int f81232_tiocmset(struct tty_struct *tty, static int f81232_open(struct tty_struct *tty, struct usb_serial_port *port) { - struct ktermios tmp_termios; int result; /* Setup termios */ if (tty) - f81232_set_termios(tty, port, &tmp_termios); + f81232_set_termios(tty, port, NULL); result = usb_submit_urb(port->interrupt_in_urb, GFP_KERNEL); if (result) { @@ -213,7 +212,6 @@ static int f81232_open(struct tty_struct *tty, struct usb_serial_port *port) return result; } - port->port.drain_delay = 256; return 0; } @@ -248,71 +246,25 @@ static int f81232_carrier_raised(struct usb_serial_port *port) return 0; } -static int wait_modem_info(struct usb_serial_port *port, unsigned int arg) -{ - struct f81232_private *priv = usb_get_serial_port_data(port); - unsigned long flags; - unsigned int prevstatus; - unsigned int status; - unsigned int changed; - - spin_lock_irqsave(&priv->lock, flags); - prevstatus = priv->line_status; - spin_unlock_irqrestore(&priv->lock, flags); - - while (1) { - interruptible_sleep_on(&priv->delta_msr_wait); - /* see if a signal did it */ - if (signal_pending(current)) - return -ERESTARTSYS; - - spin_lock_irqsave(&priv->lock, flags); - status = priv->line_status; - spin_unlock_irqrestore(&priv->lock, flags); - - changed = prevstatus ^ status; - - if (((arg & TIOCM_RNG) && (changed & UART_RING)) || - ((arg & TIOCM_DSR) && (changed & UART_DSR)) || - ((arg & TIOCM_CD) && (changed & UART_DCD)) || - ((arg & TIOCM_CTS) && (changed & UART_CTS))) { - return 0; - } - prevstatus = status; - } - /* NOTREACHED */ - return 0; -} - static int f81232_ioctl(struct tty_struct *tty, unsigned int cmd, unsigned long arg) { struct serial_struct ser; struct usb_serial_port *port = tty->driver_data; - dev_dbg(&port->dev, "%s (%d) cmd = 0x%04x\n", __func__, - port->number, cmd); - switch (cmd) { case TIOCGSERIAL: memset(&ser, 0, sizeof ser); ser.type = PORT_16654; - ser.line = port->serial->minor; - ser.port = port->number; + ser.line = port->minor; + ser.port = port->port_number; ser.baud_base = 460800; if (copy_to_user((void __user *)arg, &ser, sizeof ser)) return -EFAULT; return 0; - - case TIOCMIWAIT: - dev_dbg(&port->dev, "%s (%d) TIOCMIWAIT\n", __func__, - port->number); - return wait_modem_info(port, arg); default: - dev_dbg(&port->dev, "%s not supported = 0x%04x\n", - __func__, cmd); break; } return -ENOIOCTLCMD; @@ -327,10 +279,11 @@ static int f81232_port_probe(struct usb_serial_port *port) return -ENOMEM; spin_lock_init(&priv->lock); - init_waitqueue_head(&priv->delta_msr_wait); usb_set_serial_port_data(port, priv); + port->port.drain_delay = 256; + return 0; } @@ -362,6 +315,7 @@ static struct usb_serial_driver f81232_device = { .set_termios = f81232_set_termios, .tiocmget = f81232_tiocmget, .tiocmset = f81232_tiocmset, + .tiocmiwait = usb_serial_generic_tiocmiwait, .process_read_urb = f81232_process_read_urb, .read_int_callback = f81232_read_int_callback, .port_probe = f81232_port_probe, diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c index ba68835d06a..8a3813be1b2 100644 --- a/drivers/usb/serial/ftdi_sio.c +++ b/drivers/usb/serial/ftdi_sio.c @@ -1,7 +1,7 @@ /* * USB FTDI SIO driver * - * Copyright (C) 2009 - 2010 + * Copyright (C) 2009 - 2013 * Johan Hovold (jhovold@gmail.com) * Copyright (C) 1999 - 2001 * Greg Kroah-Hartman (greg@kroah.com) @@ -33,7 +33,6 @@ #include <linux/kernel.h> #include <linux/errno.h> -#include <linux/init.h> #include <linux/slab.h> #include <linux/tty.h> #include <linux/tty_driver.h> @@ -51,11 +50,8 @@ #define DRIVER_AUTHOR "Greg Kroah-Hartman <greg@kroah.com>, Bill Ryder <bryder@sgi.com>, Kuba Ober <kuba@mareimbrium.org>, Andreas Mohr, Johan Hovold <jhovold@gmail.com>" #define DRIVER_DESC "USB FTDI Serial Converters Driver" -static __u16 vendor = FTDI_VID; -static __u16 product; struct ftdi_private { - struct kref kref; enum ftdi_chip_type chip_type; /* type of device, either SIO or FT8U232AM */ int baud_base; /* baud base clock for divisor setting */ @@ -68,10 +64,7 @@ struct ftdi_private { */ int flags; /* some ASYNC_xxxx flags are supported */ unsigned long last_dtr_rts; /* saved modem control outputs */ - struct async_icount icount; - wait_queue_head_t delta_msr_wait; /* Used for TIOCMIWAIT */ char prev_status; /* Used for TIOCMIWAIT */ - bool dev_gone; /* Used to abort TIOCMIWAIT */ char transmit_empty; /* If transmitter is empty or not */ __u16 interface; /* FT2232C, FT2232H or FT4232H port interface (0 for FT232/245) */ @@ -148,10 +141,10 @@ static struct ftdi_sio_quirk ftdi_8u2232c_quirk = { /* - * Device ID not listed? Test via module params product/vendor or - * /sys/bus/usb/ftdi_sio/new_id, then send patch/report! + * Device ID not listed? Test it using + * /sys/bus/usb-serial/drivers/ftdi_sio/new_id and send a patch or report. */ -static struct usb_device_id id_table_combined [] = { +static const struct usb_device_id id_table_combined[] = { { USB_DEVICE(FTDI_VID, FTDI_ZEITCONTROL_TAGTRACE_MIFARE_PID) }, { USB_DEVICE(FTDI_VID, FTDI_CTI_MINI_PID) }, { USB_DEVICE(FTDI_VID, FTDI_CTI_NANO_PID) }, @@ -159,6 +152,7 @@ static struct usb_device_id id_table_combined [] = { { USB_DEVICE(FTDI_VID, FTDI_CANUSB_PID) }, { USB_DEVICE(FTDI_VID, FTDI_CANDAPTER_PID) }, { USB_DEVICE(FTDI_VID, FTDI_NXTCAM_PID) }, + { USB_DEVICE(FTDI_VID, FTDI_EV3CON_PID) }, { USB_DEVICE(FTDI_VID, FTDI_SCS_DEVICE_0_PID) }, { USB_DEVICE(FTDI_VID, FTDI_SCS_DEVICE_1_PID) }, { USB_DEVICE(FTDI_VID, FTDI_SCS_DEVICE_2_PID) }, @@ -191,10 +185,15 @@ static struct usb_device_id id_table_combined [] = { { USB_DEVICE(FTDI_VID, FTDI_OPENDCC_THROTTLE_PID) }, { USB_DEVICE(FTDI_VID, FTDI_OPENDCC_GATEWAY_PID) }, { USB_DEVICE(FTDI_VID, FTDI_OPENDCC_GBM_PID) }, + { USB_DEVICE(FTDI_VID, FTDI_OPENDCC_GBM_BOOST_PID) }, { USB_DEVICE(NEWPORT_VID, NEWPORT_AGILIS_PID) }, + { USB_DEVICE(NEWPORT_VID, NEWPORT_CONEX_CC_PID) }, + { USB_DEVICE(NEWPORT_VID, NEWPORT_CONEX_AGP_PID) }, { USB_DEVICE(INTERBIOMETRICS_VID, INTERBIOMETRICS_IOBOARD_PID) }, { USB_DEVICE(INTERBIOMETRICS_VID, INTERBIOMETRICS_MINI_IOBOARD_PID) }, { USB_DEVICE(FTDI_VID, FTDI_SPROG_II) }, + { USB_DEVICE(FTDI_VID, FTDI_TAGSYS_LP101_PID) }, + { USB_DEVICE(FTDI_VID, FTDI_TAGSYS_P200X_PID) }, { USB_DEVICE(FTDI_VID, FTDI_LENZ_LIUSB_PID) }, { USB_DEVICE(FTDI_VID, FTDI_XF_632_PID) }, { USB_DEVICE(FTDI_VID, FTDI_XF_634_PID) }, @@ -581,9 +580,12 @@ static struct usb_device_id id_table_combined [] = { { USB_DEVICE(FTDI_VID, FTDI_TAVIR_STK500_PID) }, { USB_DEVICE(FTDI_VID, FTDI_TIAO_UMPA_PID), .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, + { USB_DEVICE(FTDI_VID, FTDI_NT_ORIONLXM_PID), + .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, /* * ELV devices: */ + { USB_DEVICE(FTDI_ELV_VID, FTDI_ELV_WS300_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_USR_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_MSM1_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_KL100_PID) }, @@ -641,6 +643,7 @@ static struct usb_device_id id_table_combined [] = { { USB_DEVICE(FTDI_VID, FTDI_RM_CANVIEW_PID) }, { USB_DEVICE(ACTON_VID, ACTON_SPECTRAPRO_PID) }, { USB_DEVICE(CONTEC_VID, CONTEC_COM1USBH_PID) }, + { USB_DEVICE(MITSUBISHI_VID, MITSUBISHI_FXUSB_PID) }, { USB_DEVICE(BANDB_VID, BANDB_USOTL4_PID) }, { USB_DEVICE(BANDB_VID, BANDB_USTL4_PID) }, { USB_DEVICE(BANDB_VID, BANDB_USO9ML2_PID) }, @@ -670,6 +673,7 @@ static struct usb_device_id id_table_combined [] = { { USB_DEVICE(FTDI_VID, XSENS_CONVERTER_5_PID) }, { USB_DEVICE(FTDI_VID, XSENS_CONVERTER_6_PID) }, { USB_DEVICE(FTDI_VID, XSENS_CONVERTER_7_PID) }, + { USB_DEVICE(FTDI_VID, FTDI_OMNI1509) }, { USB_DEVICE(MOBILITY_VID, MOBILITY_USB_SERIAL_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ACTIVE_ROBOTS_PID) }, { USB_DEVICE(FTDI_VID, FTDI_MHAM_KW_PID) }, @@ -716,7 +720,8 @@ static struct usb_device_id id_table_combined [] = { { USB_DEVICE(FTDI_VID, FTDI_ACG_HFDUAL_PID) }, { USB_DEVICE(FTDI_VID, FTDI_YEI_SERVOCENTER31_PID) }, { USB_DEVICE(FTDI_VID, FTDI_THORLABS_PID) }, - { USB_DEVICE(TESTO_VID, TESTO_USB_INTERFACE_PID) }, + { USB_DEVICE(TESTO_VID, TESTO_1_PID) }, + { USB_DEVICE(TESTO_VID, TESTO_3_PID) }, { USB_DEVICE(FTDI_VID, FTDI_GAMMA_SCOUT_PID) }, { USB_DEVICE(FTDI_VID, FTDI_TACTRIX_OPENPORT_13M_PID) }, { USB_DEVICE(FTDI_VID, FTDI_TACTRIX_OPENPORT_13S_PID) }, @@ -733,9 +738,34 @@ static struct usb_device_id id_table_combined [] = { { USB_DEVICE(FTDI_VID, FTDI_NDI_AURORA_SCU_PID), .driver_info = (kernel_ulong_t)&ftdi_NDI_device_quirk }, { USB_DEVICE(TELLDUS_VID, TELLDUS_TELLSTICK_PID) }, - { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_SERIAL_VX7_PID) }, - { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_CT29B_PID) }, - { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_RTS01_PID) }, + { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_USB_S03_PID) }, + { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_USB_59_PID) }, + { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_USB_57A_PID) }, + { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_USB_57B_PID) }, + { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_USB_29A_PID) }, + { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_USB_29B_PID) }, + { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_USB_29F_PID) }, + { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_USB_62B_PID) }, + { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_USB_S01_PID) }, + { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_USB_63_PID) }, + { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_USB_29C_PID) }, + { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_USB_81B_PID) }, + { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_USB_82B_PID) }, + { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_USB_K5D_PID) }, + { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_USB_K4Y_PID) }, + { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_USB_K5G_PID) }, + { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_USB_S05_PID) }, + { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_USB_60_PID) }, + { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_USB_61_PID) }, + { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_USB_62_PID) }, + { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_USB_63B_PID) }, + { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_USB_64_PID) }, + { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_USB_65_PID) }, + { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_USB_92_PID) }, + { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_USB_92D_PID) }, + { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_USB_W5R_PID) }, + { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_USB_A5R_PID) }, + { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_USB_PW1_PID) }, { USB_DEVICE(FTDI_VID, FTDI_MAXSTREAM_PID) }, { USB_DEVICE(FTDI_VID, FTDI_PHI_FISCO_PID) }, { USB_DEVICE(TML_VID, TML_USB_SERIAL_PID) }, @@ -869,7 +899,9 @@ static struct usb_device_id id_table_combined [] = { { USB_DEVICE(FTDI_VID, FTDI_DOTEC_PID) }, { USB_DEVICE(QIHARDWARE_VID, MILKYMISTONE_JTAGSERIAL_PID), .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, - { USB_DEVICE(ST_VID, ST_STMCLT1030_PID), + { USB_DEVICE(ST_VID, ST_STMCLT_2232_PID), + .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, + { USB_DEVICE(ST_VID, ST_STMCLT_4232_PID), .driver_info = (kernel_ulong_t)&ftdi_stmclite_quirk }, { USB_DEVICE(FTDI_VID, FTDI_RF_R106) }, { USB_DEVICE(FTDI_VID, FTDI_DISTORTEC_JTAG_LOCK_PICK_PID), @@ -877,7 +909,44 @@ static struct usb_device_id id_table_combined [] = { { USB_DEVICE(FTDI_VID, FTDI_LUMEL_PD12_PID) }, /* Crucible Devices */ { USB_DEVICE(FTDI_VID, FTDI_CT_COMET_PID) }, - { }, /* Optional parameter entry */ + { USB_DEVICE(FTDI_VID, FTDI_Z3X_PID) }, + /* Cressi Devices */ + { USB_DEVICE(FTDI_VID, FTDI_CRESSI_PID) }, + /* Brainboxes Devices */ + { USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_VX_001_PID) }, + { USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_VX_012_PID) }, + { USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_VX_023_PID) }, + { USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_VX_034_PID) }, + { USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_101_PID) }, + { USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_160_1_PID) }, + { USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_160_2_PID) }, + { USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_160_3_PID) }, + { USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_160_4_PID) }, + { USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_160_5_PID) }, + { USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_160_6_PID) }, + { USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_160_7_PID) }, + { USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_160_8_PID) }, + { USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_257_PID) }, + { USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_279_1_PID) }, + { USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_279_2_PID) }, + { USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_279_3_PID) }, + { USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_279_4_PID) }, + { USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_313_PID) }, + { USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_324_PID) }, + { USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_346_1_PID) }, + { USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_346_2_PID) }, + { USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_357_PID) }, + { USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_606_1_PID) }, + { USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_606_2_PID) }, + { USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_606_3_PID) }, + { USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_701_1_PID) }, + { USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_701_2_PID) }, + { USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_842_1_PID) }, + { USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_842_2_PID) }, + { USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_842_3_PID) }, + { USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_842_4_PID) }, + /* Infineon Devices */ + { USB_DEVICE_INTERFACE_NUMBER(INFINEON_VID, INFINEON_TRIBOARD_PID, 1) }, { } /* Terminating entry */ }; @@ -901,16 +970,12 @@ static const char *ftdi_chip_name[] = { #define FTDI_STATUS_B1_MASK (FTDI_RS_BI) /* End TIOCMIWAIT */ -#define FTDI_IMPL_ASYNC_FLAGS = (ASYNC_SPD_HI | ASYNC_SPD_VHI \ - | ASYNC_SPD_CUST | ASYNC_SPD_SHI | ASYNC_SPD_WARP) - /* function prototypes for a FTDI serial converter */ static int ftdi_sio_probe(struct usb_serial *serial, const struct usb_device_id *id); static int ftdi_sio_port_probe(struct usb_serial_port *port); static int ftdi_sio_port_remove(struct usb_serial_port *port); static int ftdi_open(struct tty_struct *tty, struct usb_serial_port *port); -static void ftdi_close(struct usb_serial_port *port); static void ftdi_dtr_rts(struct usb_serial_port *port, int on); static void ftdi_process_read_urb(struct urb *urb); static int ftdi_prepare_write_buffer(struct usb_serial_port *port, @@ -920,13 +985,11 @@ static void ftdi_set_termios(struct tty_struct *tty, static int ftdi_tiocmget(struct tty_struct *tty); static int ftdi_tiocmset(struct tty_struct *tty, unsigned int set, unsigned int clear); -static int ftdi_get_icount(struct tty_struct *tty, - struct serial_icounter_struct *icount); static int ftdi_ioctl(struct tty_struct *tty, unsigned int cmd, unsigned long arg); static void ftdi_break_ctl(struct tty_struct *tty, int break_state); -static int ftdi_chars_in_buffer(struct tty_struct *tty); -static int ftdi_get_modem_status(struct tty_struct *tty, +static bool ftdi_tx_empty(struct usb_serial_port *port); +static int ftdi_get_modem_status(struct usb_serial_port *port, unsigned char status[2]); static unsigned short int ftdi_232am_baud_base_to_divisor(int baud, int base); @@ -950,7 +1013,6 @@ static struct usb_serial_driver ftdi_sio_device = { .port_probe = ftdi_sio_port_probe, .port_remove = ftdi_sio_port_remove, .open = ftdi_open, - .close = ftdi_close, .dtr_rts = ftdi_dtr_rts, .throttle = usb_serial_generic_throttle, .unthrottle = usb_serial_generic_unthrottle, @@ -958,11 +1020,12 @@ static struct usb_serial_driver ftdi_sio_device = { .prepare_write_buffer = ftdi_prepare_write_buffer, .tiocmget = ftdi_tiocmget, .tiocmset = ftdi_tiocmset, - .get_icount = ftdi_get_icount, + .tiocmiwait = usb_serial_generic_tiocmiwait, + .get_icount = usb_serial_generic_get_icount, .ioctl = ftdi_ioctl, .set_termios = ftdi_set_termios, .break_ctl = ftdi_break_ctl, - .chars_in_buffer = ftdi_chars_in_buffer, + .tx_empty = ftdi_tx_empty, }; static struct usb_serial_driver * const serial_drivers[] = { @@ -973,10 +1036,6 @@ static struct usb_serial_driver * const serial_drivers[] = { #define WDR_TIMEOUT 5000 /* default urb timeout */ #define WDR_SHORT_TIMEOUT 1000 /* shorter urb timeout */ -/* High and low are for DTR, RTS etc etc */ -#define HIGH 1 -#define LOW 0 - /* * *************************************************************************** * Utility functions @@ -1510,14 +1569,17 @@ static void ftdi_set_max_packet_size(struct usb_serial_port *port) struct usb_device *udev = serial->dev; struct usb_interface *interface = serial->interface; - struct usb_endpoint_descriptor *ep_desc = &interface->cur_altsetting->endpoint[1].desc; + struct usb_endpoint_descriptor *ep_desc; unsigned num_endpoints; - int i; + unsigned i; num_endpoints = interface->cur_altsetting->desc.bNumEndpoints; dev_info(&udev->dev, "Number of endpoints %d\n", num_endpoints); + if (!num_endpoints) + return; + /* NOTE: some customers have programmed FT232R/FT245R devices * with an endpoint size of 0 - not good. In this case, we * want to override the endpoint descriptor setting and use a @@ -1545,8 +1607,8 @@ static void ftdi_set_max_packet_size(struct usb_serial_port *port) * *************************************************************************** */ -static ssize_t show_latency_timer(struct device *dev, - struct device_attribute *attr, char *buf) +static ssize_t latency_timer_show(struct device *dev, + struct device_attribute *attr, char *buf) { struct usb_serial_port *port = to_usb_serial_port(dev); struct ftdi_private *priv = usb_get_serial_port_data(port); @@ -1556,11 +1618,10 @@ static ssize_t show_latency_timer(struct device *dev, return sprintf(buf, "%i\n", priv->latency); } - /* Write a new value of the latency timer, in units of milliseconds. */ -static ssize_t store_latency_timer(struct device *dev, - struct device_attribute *attr, const char *valbuf, - size_t count) +static ssize_t latency_timer_store(struct device *dev, + struct device_attribute *attr, + const char *valbuf, size_t count) { struct usb_serial_port *port = to_usb_serial_port(dev); struct ftdi_private *priv = usb_get_serial_port_data(port); @@ -1573,6 +1634,7 @@ static ssize_t store_latency_timer(struct device *dev, return -EIO; return count; } +static DEVICE_ATTR_RW(latency_timer); /* Write an event character directly to the FTDI register. The ASCII value is in the low 8 bits, with the enable bit in the 9th bit. */ @@ -1600,9 +1662,6 @@ static ssize_t store_event_char(struct device *dev, return count; } - -static DEVICE_ATTR(latency_timer, S_IWUSR | S_IRUGO, show_latency_timer, - store_latency_timer); static DEVICE_ATTR(event_char, S_IWUSR, NULL, store_event_char); static int create_sysfs_attrs(struct usb_serial_port *port) @@ -1681,18 +1740,12 @@ static int ftdi_sio_port_probe(struct usb_serial_port *port) priv = kzalloc(sizeof(struct ftdi_private), GFP_KERNEL); - if (!priv) { - dev_err(&port->dev, "%s- kmalloc(%Zd) failed.\n", __func__, - sizeof(struct ftdi_private)); + if (!priv) return -ENOMEM; - } - kref_init(&priv->kref); mutex_init(&priv->cfg_lock); - init_waitqueue_head(&priv->delta_msr_wait); priv->flags = ASYNC_LOW_LATENCY; - priv->dev_gone = false; if (quirk && quirk->port_probe) quirk->port_probe(priv); @@ -1793,20 +1846,24 @@ static int ftdi_8u2232c_probe(struct usb_serial *serial) } /* - * First and second port on STMCLiteadaptors is reserved for JTAG interface - * and the forth port for pio + * First two ports on JTAG adaptors using an FT4232 such as STMicroelectronics's + * ST Micro Connect Lite are reserved for JTAG or other non-UART interfaces and + * can be accessed from userspace. + * The next two ports are enabled as UARTs by default, where port 2 is + * a conventional RS-232 UART. */ static int ftdi_stmclite_probe(struct usb_serial *serial) { struct usb_device *udev = serial->dev; struct usb_interface *interface = serial->interface; - if (interface == udev->actconfig->interface[2]) - return 0; - - dev_info(&udev->dev, "Ignoring serial port reserved for JTAG\n"); + if (interface == udev->actconfig->interface[0] || + interface == udev->actconfig->interface[1]) { + dev_info(&udev->dev, "Ignoring serial port reserved for JTAG\n"); + return -ENODEV; + } - return -ENODEV; + return 0; } /* @@ -1827,33 +1884,21 @@ static int ftdi_mtxorb_hack_setup(struct usb_serial *serial) return 0; } -static void ftdi_sio_priv_release(struct kref *k) -{ - struct ftdi_private *priv = container_of(k, struct ftdi_private, kref); - - kfree(priv); -} - static int ftdi_sio_port_remove(struct usb_serial_port *port) { struct ftdi_private *priv = usb_get_serial_port_data(port); - priv->dev_gone = true; - wake_up_interruptible_all(&priv->delta_msr_wait); - remove_sysfs_attrs(port); - kref_put(&priv->kref, ftdi_sio_priv_release); + kfree(priv); return 0; } static int ftdi_open(struct tty_struct *tty, struct usb_serial_port *port) { - struct ktermios dummy; struct usb_device *dev = port->serial->dev; struct ftdi_private *priv = usb_get_serial_port_data(port); - int result; /* No error checking for this (will get errors later anyway) */ /* See ftdi_sio.h for description of what is reset */ @@ -1867,54 +1912,32 @@ static int ftdi_open(struct tty_struct *tty, struct usb_serial_port *port) This is same behaviour as serial.c/rs_open() - Kuba */ /* ftdi_set_termios will send usb control messages */ - if (tty) { - memset(&dummy, 0, sizeof(dummy)); - ftdi_set_termios(tty, port, &dummy); - } - - /* Start reading from the device */ - result = usb_serial_generic_open(tty, port); - if (!result) - kref_get(&priv->kref); + if (tty) + ftdi_set_termios(tty, port, NULL); - return result; + return usb_serial_generic_open(tty, port); } static void ftdi_dtr_rts(struct usb_serial_port *port, int on) { struct ftdi_private *priv = usb_get_serial_port_data(port); - mutex_lock(&port->serial->disc_mutex); - if (!port->serial->disconnected) { - /* Disable flow control */ - if (!on && usb_control_msg(port->serial->dev, + /* Disable flow control */ + if (!on) { + if (usb_control_msg(port->serial->dev, usb_sndctrlpipe(port->serial->dev, 0), FTDI_SIO_SET_FLOW_CTRL_REQUEST, FTDI_SIO_SET_FLOW_CTRL_REQUEST_TYPE, 0, priv->interface, NULL, 0, WDR_TIMEOUT) < 0) { - dev_err(&port->dev, "error from flowcontrol urb\n"); + dev_err(&port->dev, "error from flowcontrol urb\n"); } - /* drop RTS and DTR */ - if (on) - set_mctrl(port, TIOCM_DTR | TIOCM_RTS); - else - clear_mctrl(port, TIOCM_DTR | TIOCM_RTS); } - mutex_unlock(&port->serial->disc_mutex); -} - -/* - * usbserial:__serial_close only calls ftdi_close if the point is open - * - * This only gets called when it is the last close - */ -static void ftdi_close(struct usb_serial_port *port) -{ - struct ftdi_private *priv = usb_get_serial_port_data(port); - - usb_serial_generic_close(port); - kref_put(&priv->kref, ftdi_sio_priv_release); + /* drop RTS and DTR */ + if (on) + set_mctrl(port, TIOCM_DTR | TIOCM_RTS); + else + clear_mctrl(port, TIOCM_DTR | TIOCM_RTS); } /* The SIO requires the first byte to have: @@ -1944,7 +1967,7 @@ static int ftdi_prepare_write_buffer(struct usb_serial_port *port, c = kfifo_out(&port->write_fifo, &buffer[i + 1], len); if (!c) break; - priv->icount.tx += c; + port->icount.tx += c; buffer[i] = (c << 2) + 1; count += c + 1; } @@ -1952,7 +1975,7 @@ static int ftdi_prepare_write_buffer(struct usb_serial_port *port, } else { count = kfifo_out_locked(&port->write_fifo, dest, size, &port->lock); - priv->icount.tx += count; + port->icount.tx += count; } return count; @@ -1960,9 +1983,8 @@ static int ftdi_prepare_write_buffer(struct usb_serial_port *port, #define FTDI_RS_ERR_MASK (FTDI_RS_BI | FTDI_RS_PE | FTDI_RS_FE | FTDI_RS_OE) -static int ftdi_process_packet(struct tty_struct *tty, - struct usb_serial_port *port, struct ftdi_private *priv, - char *packet, int len) +static int ftdi_process_packet(struct usb_serial_port *port, + struct ftdi_private *priv, char *packet, int len) { int i; char status; @@ -1982,15 +2004,23 @@ static int ftdi_process_packet(struct tty_struct *tty, char diff_status = status ^ priv->prev_status; if (diff_status & FTDI_RS0_CTS) - priv->icount.cts++; + port->icount.cts++; if (diff_status & FTDI_RS0_DSR) - priv->icount.dsr++; + port->icount.dsr++; if (diff_status & FTDI_RS0_RI) - priv->icount.rng++; - if (diff_status & FTDI_RS0_RLSD) - priv->icount.dcd++; + port->icount.rng++; + if (diff_status & FTDI_RS0_RLSD) { + struct tty_struct *tty; + + port->icount.dcd++; + tty = tty_port_tty_get(&port->port); + if (tty) + usb_serial_handle_dcd_change(port, tty, + status & FTDI_RS0_RLSD); + tty_kref_put(tty); + } - wake_up_interruptible_all(&priv->delta_msr_wait); + wake_up_interruptible(&port->port.delta_msr_wait); priv->prev_status = status; } @@ -2000,19 +2030,19 @@ static int ftdi_process_packet(struct tty_struct *tty, * over framing errors */ if (packet[1] & FTDI_RS_BI) { flag = TTY_BREAK; - priv->icount.brk++; + port->icount.brk++; usb_serial_handle_break(port); } else if (packet[1] & FTDI_RS_PE) { flag = TTY_PARITY; - priv->icount.parity++; + port->icount.parity++; } else if (packet[1] & FTDI_RS_FE) { flag = TTY_FRAME; - priv->icount.frame++; + port->icount.frame++; } /* Overrun is special, not associated with a char */ if (packet[1] & FTDI_RS_OE) { - priv->icount.overrun++; - tty_insert_flip_char(tty, 0, TTY_OVERRUN); + port->icount.overrun++; + tty_insert_flip_char(&port->port, 0, TTY_OVERRUN); } } @@ -2025,16 +2055,16 @@ static int ftdi_process_packet(struct tty_struct *tty, len -= 2; if (!len) return 0; /* status only */ - priv->icount.rx += len; + port->icount.rx += len; ch = packet + 2; if (port->port.console && port->sysrq) { for (i = 0; i < len; i++, ch++) { if (!usb_serial_handle_sysrq_char(port, *ch)) - tty_insert_flip_char(tty, *ch, flag); + tty_insert_flip_char(&port->port, *ch, flag); } } else { - tty_insert_flip_string_fixed_flag(tty, ch, flag, len); + tty_insert_flip_string_fixed_flag(&port->port, ch, flag, len); } return len; @@ -2043,25 +2073,19 @@ static int ftdi_process_packet(struct tty_struct *tty, static void ftdi_process_read_urb(struct urb *urb) { struct usb_serial_port *port = urb->context; - struct tty_struct *tty; struct ftdi_private *priv = usb_get_serial_port_data(port); char *data = (char *)urb->transfer_buffer; int i; int len; int count = 0; - tty = tty_port_tty_get(&port->port); - if (!tty) - return; - for (i = 0; i < urb->actual_length; i += priv->max_packet_size) { len = min_t(int, urb->actual_length - i, priv->max_packet_size); - count += ftdi_process_packet(tty, port, priv, &data[i], len); + count += ftdi_process_packet(port, priv, &data[i], len); } if (count) - tty_flip_buffer_push(tty); - tty_kref_put(tty); + tty_flip_buffer_push(&port->port); } static void ftdi_break_ctl(struct tty_struct *tty, int break_state) @@ -2094,27 +2118,18 @@ static void ftdi_break_ctl(struct tty_struct *tty, int break_state) } -static int ftdi_chars_in_buffer(struct tty_struct *tty) +static bool ftdi_tx_empty(struct usb_serial_port *port) { - struct usb_serial_port *port = tty->driver_data; - int chars; unsigned char buf[2]; int ret; - chars = usb_serial_generic_chars_in_buffer(tty); - if (chars) - goto out; - - /* Check if hardware buffer is empty. */ - ret = ftdi_get_modem_status(tty, buf); + ret = ftdi_get_modem_status(port, buf); if (ret == 2) { if (!(buf[1] & FTDI_RS_TEMT)) - chars = 1; + return false; } -out: - dev_dbg(&port->dev, "%s - %d\n", __func__, chars); - return chars; + return true; } /* old_termios contains the original termios settings and tty->termios contains @@ -2150,6 +2165,30 @@ static void ftdi_set_termios(struct tty_struct *tty, termios->c_cflag |= CRTSCTS; } + /* + * All FTDI UART chips are limited to CS7/8. We shouldn't pretend to + * support CS5/6 and revert the CSIZE setting instead. + * + * CS5 however is used to control some smartcard readers which abuse + * this limitation to switch modes. Original FTDI chips fall back to + * eight data bits. + * + * TODO: Implement a quirk to only allow this with mentioned + * readers. One I know of (Argolis Smartreader V1) + * returns "USB smartcard server" as iInterface string. + * The vendor didn't bother with a custom VID/PID of + * course. + */ + if (C_CSIZE(tty) == CS6) { + dev_warn(ddev, "requested CSIZE setting not supported\n"); + + termios->c_cflag &= ~CSIZE; + if (old_termios) + termios->c_cflag |= old_termios->c_cflag & CSIZE; + else + termios->c_cflag |= CS8; + } + cflag = termios->c_cflag; if (!old_termios) @@ -2186,19 +2225,19 @@ no_skip: } else { urb_value |= FTDI_SIO_SET_DATA_PARITY_NONE; } - if (cflag & CSIZE) { - switch (cflag & CSIZE) { - case CS7: - urb_value |= 7; - dev_dbg(ddev, "Setting CS7\n"); - break; - case CS8: - urb_value |= 8; - dev_dbg(ddev, "Setting CS8\n"); - break; - default: - dev_err(ddev, "CSIZE was set but not CS7-CS8\n"); - } + switch (cflag & CSIZE) { + case CS5: + dev_dbg(ddev, "Setting CS5 quirk\n"); + break; + case CS7: + urb_value |= 7; + dev_dbg(ddev, "Setting CS7\n"); + break; + default: + case CS8: + urb_value |= 8; + dev_dbg(ddev, "Setting CS8\n"); + break; } /* This is needed by the break command since it uses the same command @@ -2235,7 +2274,7 @@ no_data_parity_stop_changes: dev_err(ddev, "%s urb failed to set baudrate\n", __func__); mutex_unlock(&priv->cfg_lock); /* Ensure RTS and DTR are raised when baudrate changed from 0 */ - if (!old_termios || (old_termios->c_cflag & CBAUD) == B0) + if (old_termios && (old_termios->c_cflag & CBAUD) == B0) set_mctrl(port, TIOCM_DTR | TIOCM_RTS); } @@ -2306,10 +2345,9 @@ no_c_cflag_changes: * Returns the number of status bytes retrieved (device dependant), or * negative error code. */ -static int ftdi_get_modem_status(struct tty_struct *tty, +static int ftdi_get_modem_status(struct usb_serial_port *port, unsigned char status[2]) { - struct usb_serial_port *port = tty->driver_data; struct ftdi_private *priv = usb_get_serial_port_data(port); unsigned char *buf; int len; @@ -2374,7 +2412,7 @@ static int ftdi_tiocmget(struct tty_struct *tty) unsigned char buf[2]; int ret; - ret = ftdi_get_modem_status(tty, buf); + ret = ftdi_get_modem_status(port, buf); if (ret < 0) return ret; @@ -2395,36 +2433,10 @@ static int ftdi_tiocmset(struct tty_struct *tty, return update_mctrl(port, set, clear); } -static int ftdi_get_icount(struct tty_struct *tty, - struct serial_icounter_struct *icount) -{ - struct usb_serial_port *port = tty->driver_data; - struct ftdi_private *priv = usb_get_serial_port_data(port); - struct async_icount *ic = &priv->icount; - - icount->cts = ic->cts; - icount->dsr = ic->dsr; - icount->rng = ic->rng; - icount->dcd = ic->dcd; - icount->tx = ic->tx; - icount->rx = ic->rx; - icount->frame = ic->frame; - icount->parity = ic->parity; - icount->overrun = ic->overrun; - icount->brk = ic->brk; - icount->buf_overrun = ic->buf_overrun; - return 0; -} - static int ftdi_ioctl(struct tty_struct *tty, unsigned int cmd, unsigned long arg) { struct usb_serial_port *port = tty->driver_data; - struct ftdi_private *priv = usb_get_serial_port_data(port); - struct async_icount cnow; - struct async_icount cprev; - - dev_dbg(&port->dev, "%s cmd 0x%04x\n", __func__, cmd); /* Based on code from acm.c and others */ switch (cmd) { @@ -2436,79 +2448,21 @@ static int ftdi_ioctl(struct tty_struct *tty, case TIOCSSERIAL: /* sets serial port data */ return set_serial_info(tty, port, (struct serial_struct __user *) arg); - - /* - * Wait for any of the 4 modem inputs (DCD,RI,DSR,CTS) to change - * - mask passed in arg for lines of interest - * (use |'ed TIOCM_RNG/DSR/CD/CTS for masking) - * Caller should use TIOCGICOUNT to see which one it was. - * - * This code is borrowed from linux/drivers/char/serial.c - */ - case TIOCMIWAIT: - cprev = priv->icount; - while (!priv->dev_gone) { - interruptible_sleep_on(&priv->delta_msr_wait); - /* see if a signal did it */ - if (signal_pending(current)) - return -ERESTARTSYS; - cnow = priv->icount; - if (((arg & TIOCM_RNG) && (cnow.rng != cprev.rng)) || - ((arg & TIOCM_DSR) && (cnow.dsr != cprev.dsr)) || - ((arg & TIOCM_CD) && (cnow.dcd != cprev.dcd)) || - ((arg & TIOCM_CTS) && (cnow.cts != cprev.cts))) { - return 0; - } - cprev = cnow; - } - return -EIO; - break; case TIOCSERGETLSR: return get_lsr_info(port, (struct serial_struct __user *)arg); break; default: break; } - /* This is not necessarily an error - turns out the higher layers - * will do some ioctls themselves (see comment above) - */ - dev_dbg(&port->dev, "%s arg not supported - it was 0x%04x - check /usr/include/asm/ioctls.h\n", - __func__, cmd); - return -ENOIOCTLCMD; -} - -static int __init ftdi_init(void) -{ - if (vendor > 0 && product > 0) { - /* Add user specified VID/PID to reserved element of table. */ - int i; - for (i = 0; id_table_combined[i].idVendor; i++) - ; - id_table_combined[i].match_flags = USB_DEVICE_ID_MATCH_DEVICE; - id_table_combined[i].idVendor = vendor; - id_table_combined[i].idProduct = product; - } - return usb_serial_register_drivers(serial_drivers, KBUILD_MODNAME, id_table_combined); -} -static void __exit ftdi_exit(void) -{ - usb_serial_deregister_drivers(serial_drivers); + return -ENOIOCTLCMD; } - -module_init(ftdi_init); -module_exit(ftdi_exit); +module_usb_serial_driver(serial_drivers, id_table_combined); MODULE_AUTHOR(DRIVER_AUTHOR); MODULE_DESCRIPTION(DRIVER_DESC); MODULE_LICENSE("GPL"); -module_param(vendor, ushort, 0); -MODULE_PARM_DESC(vendor, "User specified vendor ID (default=" - __MODULE_STRING(FTDI_VID)")"); -module_param(product, ushort, 0); -MODULE_PARM_DESC(product, "User specified product ID"); - module_param(ndi_latency_timer, int, S_IRUGO | S_IWUSR); MODULE_PARM_DESC(ndi_latency_timer, "NDI device latency timer override"); diff --git a/drivers/usb/serial/ftdi_sio_ids.h b/drivers/usb/serial/ftdi_sio_ids.h index fa5d5603827..c4777bc6aee 100644 --- a/drivers/usb/serial/ftdi_sio_ids.h +++ b/drivers/usb/serial/ftdi_sio_ids.h @@ -50,6 +50,7 @@ #define TI_XDS100V2_PID 0xa6d0 #define FTDI_NXTCAM_PID 0xABB8 /* NXTCam for Mindstorms NXT */ +#define FTDI_EV3CON_PID 0xABB9 /* Mindstorms EV3 Console Adapter */ /* US Interface Navigator (http://www.usinterface.com/) */ #define FTDI_USINT_CAT_PID 0xb810 /* Navigator CAT and 2nd PTT lines */ @@ -74,6 +75,7 @@ #define FTDI_OPENDCC_THROTTLE_PID 0xBFDA #define FTDI_OPENDCC_GATEWAY_PID 0xBFDB #define FTDI_OPENDCC_GBM_PID 0xBFDC +#define FTDI_OPENDCC_GBM_BOOST_PID 0xBFDD /* NZR SEM 16+ USB (http://www.nzr.de) */ #define FTDI_NZR_SEM_USB_PID 0xC1E0 /* NZR SEM-LOG16+ */ @@ -147,6 +149,11 @@ #define XSENS_CONVERTER_6_PID 0xD38E #define XSENS_CONVERTER_7_PID 0xD38F +/** + * Zolix (www.zolix.com.cb) product ids + */ +#define FTDI_OMNI1509 0xD491 /* Omni1509 embedded USB-serial */ + /* * NDI (www.ndigital.com) product ids */ @@ -204,7 +211,7 @@ /* * ELV USB devices submitted by Christian Abt of ELV (www.elv.de). - * All of these devices use FTDI's vendor ID (0x0403). + * Almost all of these devices use FTDI's vendor ID (0x0403). * Further IDs taken from ELV Windows .inf file. * * The previously included PID for the UO 100 module was incorrect. @@ -212,6 +219,8 @@ * * Armin Laeuger originally sent the PID for the UM 100 module. */ +#define FTDI_ELV_VID 0x1B1F /* ELV AG */ +#define FTDI_ELV_WS300_PID 0xC006 /* eQ3 WS 300 PC II */ #define FTDI_ELV_USR_PID 0xE000 /* ELV Universal-Sound-Recorder */ #define FTDI_ELV_MSM1_PID 0xE001 /* ELV Mini-Sound-Modul */ #define FTDI_ELV_KL100_PID 0xE002 /* ELV Kfz-Leistungsmesser KL 100 */ @@ -355,6 +364,12 @@ /* Sprog II (Andrew Crosland's SprogII DCC interface) */ #define FTDI_SPROG_II 0xF0C8 +/* + * Two of the Tagsys RFID Readers + */ +#define FTDI_TAGSYS_LP101_PID 0xF0E9 /* Tagsys L-P101 RFID*/ +#define FTDI_TAGSYS_P200X_PID 0xF0EE /* Tagsys Medio P200x RFID*/ + /* an infrared receiver for user access control with IR tags */ #define FTDI_PIEGROUP_PID 0xF208 /* Product Id */ @@ -523,6 +538,11 @@ */ #define FTDI_TIAO_UMPA_PID 0x8a98 /* TIAO/DIYGADGET USB Multi-Protocol Adapter */ +/* + * NovaTech product ids (FTDI_VID) + */ +#define FTDI_NT_ORIONLXM_PID 0x7c90 /* OrionLXm Substation Automation Platform */ + /********************************/ /** third-party VID/PID combos **/ @@ -564,6 +584,12 @@ #define RATOC_PRODUCT_ID_USB60F 0xb020 /* + * Infineon Technologies + */ +#define INFINEON_VID 0x058b +#define INFINEON_TRIBOARD_PID 0x0028 /* DAS JTAG TriBoard TC1798 V1.0 */ + +/* * Acton Research Corp. */ #define ACTON_VID 0x0647 /* Vendor ID */ @@ -577,6 +603,13 @@ #define CONTEC_COM1USBH_PID 0x8311 /* COM-1(USB)H */ /* + * Mitsubishi Electric Corp. (http://www.meau.com) + * Submitted by Konstantin Holoborodko + */ +#define MITSUBISHI_VID 0x06D3 +#define MITSUBISHI_FXUSB_PID 0x0284 /* USB/RS422 converters: FX-USB-AW/-BD */ + +/* * Definitions for B&B Electronics products. */ #define BANDB_VID 0x0856 /* B&B Electronics Vendor ID */ @@ -757,6 +790,8 @@ */ #define NEWPORT_VID 0x104D #define NEWPORT_AGILIS_PID 0x3000 +#define NEWPORT_CONEX_CC_PID 0x3002 +#define NEWPORT_CONEX_AGP_PID 0x3006 /* Interbiometrics USB I/O Board */ /* Developed for Interbiometrics by Rudolf Gugler */ @@ -769,7 +804,8 @@ * Submitted by Colin Leroy */ #define TESTO_VID 0x128D -#define TESTO_USB_INTERFACE_PID 0x0001 +#define TESTO_1_PID 0x0001 +#define TESTO_3_PID 0x0003 /* * Mobility Electronics products. @@ -798,11 +834,35 @@ /* * RT Systems programming cables for various ham radios */ -#define RTSYSTEMS_VID 0x2100 /* Vendor ID */ -#define RTSYSTEMS_SERIAL_VX7_PID 0x9e52 /* Serial converter for VX-7 Radios using FT232RL */ -#define RTSYSTEMS_CT29B_PID 0x9e54 /* CT29B Radio Cable */ -#define RTSYSTEMS_RTS01_PID 0x9e57 /* USB-RTS01 Radio Cable */ - +#define RTSYSTEMS_VID 0x2100 /* Vendor ID */ +#define RTSYSTEMS_USB_S03_PID 0x9001 /* RTS-03 USB to Serial Adapter */ +#define RTSYSTEMS_USB_59_PID 0x9e50 /* USB-59 USB to 8 pin plug */ +#define RTSYSTEMS_USB_57A_PID 0x9e51 /* USB-57A USB to 4pin 3.5mm plug */ +#define RTSYSTEMS_USB_57B_PID 0x9e52 /* USB-57B USB to extended 4pin 3.5mm plug */ +#define RTSYSTEMS_USB_29A_PID 0x9e53 /* USB-29A USB to 3.5mm stereo plug */ +#define RTSYSTEMS_USB_29B_PID 0x9e54 /* USB-29B USB to 6 pin mini din */ +#define RTSYSTEMS_USB_29F_PID 0x9e55 /* USB-29F USB to 6 pin modular plug */ +#define RTSYSTEMS_USB_62B_PID 0x9e56 /* USB-62B USB to 8 pin mini din plug*/ +#define RTSYSTEMS_USB_S01_PID 0x9e57 /* USB-RTS01 USB to 3.5 mm stereo plug*/ +#define RTSYSTEMS_USB_63_PID 0x9e58 /* USB-63 USB to 9 pin female*/ +#define RTSYSTEMS_USB_29C_PID 0x9e59 /* USB-29C USB to 4 pin modular plug*/ +#define RTSYSTEMS_USB_81B_PID 0x9e5A /* USB-81 USB to 8 pin mini din plug*/ +#define RTSYSTEMS_USB_82B_PID 0x9e5B /* USB-82 USB to 2.5 mm stereo plug*/ +#define RTSYSTEMS_USB_K5D_PID 0x9e5C /* USB-K5D USB to 8 pin modular plug*/ +#define RTSYSTEMS_USB_K4Y_PID 0x9e5D /* USB-K4Y USB to 2.5/3.5 mm plugs*/ +#define RTSYSTEMS_USB_K5G_PID 0x9e5E /* USB-K5G USB to 8 pin modular plug*/ +#define RTSYSTEMS_USB_S05_PID 0x9e5F /* USB-RTS05 USB to 2.5 mm stereo plug*/ +#define RTSYSTEMS_USB_60_PID 0x9e60 /* USB-60 USB to 6 pin din*/ +#define RTSYSTEMS_USB_61_PID 0x9e61 /* USB-61 USB to 6 pin mini din*/ +#define RTSYSTEMS_USB_62_PID 0x9e62 /* USB-62 USB to 8 pin mini din*/ +#define RTSYSTEMS_USB_63B_PID 0x9e63 /* USB-63 USB to 9 pin female*/ +#define RTSYSTEMS_USB_64_PID 0x9e64 /* USB-64 USB to 9 pin male*/ +#define RTSYSTEMS_USB_65_PID 0x9e65 /* USB-65 USB to 9 pin female null modem*/ +#define RTSYSTEMS_USB_92_PID 0x9e66 /* USB-92 USB to 12 pin plug*/ +#define RTSYSTEMS_USB_92D_PID 0x9e67 /* USB-92D USB to 12 pin plug data*/ +#define RTSYSTEMS_USB_W5R_PID 0x9e68 /* USB-W5R USB to 8 pin modular plug*/ +#define RTSYSTEMS_USB_A5R_PID 0x9e69 /* USB-A5R USB to 8 pin modular plug*/ +#define RTSYSTEMS_USB_PW1_PID 0x9e6A /* USB-PW1 USB to 8 pin modular plug*/ /* * Physik Instrumente @@ -1136,7 +1196,8 @@ * STMicroelectonics */ #define ST_VID 0x0483 -#define ST_STMCLT1030_PID 0x3747 /* ST Micro Connect Lite STMCLT1030 */ +#define ST_STMCLT_2232_PID 0x3746 +#define ST_STMCLT_4232_PID 0x3747 /* * Papouch products (http://www.papouch.com/) @@ -1265,3 +1326,52 @@ * Manufacturer: Crucible Technologies */ #define FTDI_CT_COMET_PID 0x8e08 + +/* + * Product: Z3X Box + * Manufacturer: Smart GSM Team + */ +#define FTDI_Z3X_PID 0x0011 + +/* + * Product: Cressi PC Interface + * Manufacturer: Cressi + */ +#define FTDI_CRESSI_PID 0x87d0 + +/* + * Brainboxes devices + */ +#define BRAINBOXES_VID 0x05d1 +#define BRAINBOXES_VX_001_PID 0x1001 /* VX-001 ExpressCard 1 Port RS232 */ +#define BRAINBOXES_VX_012_PID 0x1002 /* VX-012 ExpressCard 2 Port RS232 */ +#define BRAINBOXES_VX_023_PID 0x1003 /* VX-023 ExpressCard 1 Port RS422/485 */ +#define BRAINBOXES_VX_034_PID 0x1004 /* VX-034 ExpressCard 2 Port RS422/485 */ +#define BRAINBOXES_US_101_PID 0x1011 /* US-101 1xRS232 */ +#define BRAINBOXES_US_324_PID 0x1013 /* US-324 1xRS422/485 1Mbaud */ +#define BRAINBOXES_US_606_1_PID 0x2001 /* US-606 6 Port RS232 Serial Port 1 and 2 */ +#define BRAINBOXES_US_606_2_PID 0x2002 /* US-606 6 Port RS232 Serial Port 3 and 4 */ +#define BRAINBOXES_US_606_3_PID 0x2003 /* US-606 6 Port RS232 Serial Port 4 and 6 */ +#define BRAINBOXES_US_701_1_PID 0x2011 /* US-701 4xRS232 1Mbaud Port 1 and 2 */ +#define BRAINBOXES_US_701_2_PID 0x2012 /* US-701 4xRS422 1Mbaud Port 3 and 4 */ +#define BRAINBOXES_US_279_1_PID 0x2021 /* US-279 8xRS422 1Mbaud Port 1 and 2 */ +#define BRAINBOXES_US_279_2_PID 0x2022 /* US-279 8xRS422 1Mbaud Port 3 and 4 */ +#define BRAINBOXES_US_279_3_PID 0x2023 /* US-279 8xRS422 1Mbaud Port 5 and 6 */ +#define BRAINBOXES_US_279_4_PID 0x2024 /* US-279 8xRS422 1Mbaud Port 7 and 8 */ +#define BRAINBOXES_US_346_1_PID 0x3011 /* US-346 4xRS422/485 1Mbaud Port 1 and 2 */ +#define BRAINBOXES_US_346_2_PID 0x3012 /* US-346 4xRS422/485 1Mbaud Port 3 and 4 */ +#define BRAINBOXES_US_257_PID 0x5001 /* US-257 2xRS232 1Mbaud */ +#define BRAINBOXES_US_313_PID 0x6001 /* US-313 2xRS422/485 1Mbaud */ +#define BRAINBOXES_US_357_PID 0x7001 /* US_357 1xRS232/422/485 */ +#define BRAINBOXES_US_842_1_PID 0x8001 /* US-842 8xRS422/485 1Mbaud Port 1 and 2 */ +#define BRAINBOXES_US_842_2_PID 0x8002 /* US-842 8xRS422/485 1Mbaud Port 3 and 4 */ +#define BRAINBOXES_US_842_3_PID 0x8003 /* US-842 8xRS422/485 1Mbaud Port 5 and 6 */ +#define BRAINBOXES_US_842_4_PID 0x8004 /* US-842 8xRS422/485 1Mbaud Port 7 and 8 */ +#define BRAINBOXES_US_160_1_PID 0x9001 /* US-160 16xRS232 1Mbaud Port 1 and 2 */ +#define BRAINBOXES_US_160_2_PID 0x9002 /* US-160 16xRS232 1Mbaud Port 3 and 4 */ +#define BRAINBOXES_US_160_3_PID 0x9003 /* US-160 16xRS232 1Mbaud Port 5 and 6 */ +#define BRAINBOXES_US_160_4_PID 0x9004 /* US-160 16xRS232 1Mbaud Port 7 and 8 */ +#define BRAINBOXES_US_160_5_PID 0x9005 /* US-160 16xRS232 1Mbaud Port 9 and 10 */ +#define BRAINBOXES_US_160_6_PID 0x9006 /* US-160 16xRS232 1Mbaud Port 11 and 12 */ +#define BRAINBOXES_US_160_7_PID 0x9007 /* US-160 16xRS232 1Mbaud Port 13 and 14 */ +#define BRAINBOXES_US_160_8_PID 0x9008 /* US-160 16xRS232 1Mbaud Port 15 and 16 */ diff --git a/drivers/usb/serial/funsoft.c b/drivers/usb/serial/funsoft.c deleted file mode 100644 index 9362f8fd238..00000000000 --- a/drivers/usb/serial/funsoft.c +++ /dev/null @@ -1,40 +0,0 @@ -/* - * Funsoft Serial USB driver - * - * Copyright (C) 2006 Greg Kroah-Hartman <gregkh@suse.de> - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License version - * 2 as published by the Free Software Foundation. - */ - -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/tty.h> -#include <linux/module.h> -#include <linux/usb.h> -#include <linux/usb/serial.h> -#include <linux/uaccess.h> - -static const struct usb_device_id id_table[] = { - { USB_DEVICE(0x1404, 0xcddc) }, - { }, -}; -MODULE_DEVICE_TABLE(usb, id_table); - -static struct usb_serial_driver funsoft_device = { - .driver = { - .owner = THIS_MODULE, - .name = "funsoft", - }, - .id_table = id_table, - .num_ports = 1, -}; - -static struct usb_serial_driver * const serial_drivers[] = { - &funsoft_device, NULL -}; - -module_usb_serial_driver(serial_drivers, id_table); - -MODULE_LICENSE("GPL"); diff --git a/drivers/usb/serial/garmin_gps.c b/drivers/usb/serial/garmin_gps.c index 203358d7e7b..db591d19d41 100644 --- a/drivers/usb/serial/garmin_gps.c +++ b/drivers/usb/serial/garmin_gps.c @@ -25,7 +25,6 @@ #include <linux/kernel.h> #include <linux/errno.h> -#include <linux/init.h> #include <linux/slab.h> #include <linux/timer.h> #include <linux/tty.h> @@ -252,14 +251,11 @@ static inline int isAbortTrfCmnd(const unsigned char *buf) static void send_to_tty(struct usb_serial_port *port, char *data, unsigned int actual_length) { - struct tty_struct *tty = tty_port_tty_get(&port->port); - - if (tty && actual_length) { + if (actual_length) { usb_serial_debug_data(&port->dev, __func__, actual_length, data); - tty_insert_flip_string(tty, data, actual_length); - tty_flip_buffer_push(tty); + tty_insert_flip_string(&port->port, data, actual_length); + tty_flip_buffer_push(&port->port); } - tty_kref_put(tty); } @@ -278,14 +274,13 @@ static int pkt_add(struct garmin_data *garmin_data_p, unsigned long flags; struct garmin_packet *pkt; - /* process only packets containg data ... */ + /* process only packets containing data ... */ if (data_length) { pkt = kmalloc(sizeof(struct garmin_packet)+data_length, GFP_ATOMIC); - if (pkt == NULL) { - dev_err(&garmin_data_p->port->dev, "out of memory\n"); + if (!pkt) return 0; - } + pkt->size = data_length; memcpy(pkt->data, data, data_length); @@ -949,20 +944,13 @@ static int garmin_open(struct tty_struct *tty, struct usb_serial_port *port) static void garmin_close(struct usb_serial_port *port) { - struct usb_serial *serial = port->serial; struct garmin_data *garmin_data_p = usb_get_serial_port_data(port); - dev_dbg(&port->dev, "%s - port %d - mode=%d state=%d flags=0x%X\n", - __func__, port->number, garmin_data_p->mode, - garmin_data_p->state, garmin_data_p->flags); - - if (!serial) - return; - - mutex_lock(&port->serial->disc_mutex); + dev_dbg(&port->dev, "%s - mode=%d state=%d flags=0x%X\n", + __func__, garmin_data_p->mode, garmin_data_p->state, + garmin_data_p->flags); - if (!port->serial->disconnected) - garmin_clear(garmin_data_p); + garmin_clear(garmin_data_p); /* shutdown our urbs */ usb_kill_urb(port->read_urb); @@ -971,8 +959,6 @@ static void garmin_close(struct usb_serial_port *port) /* keep reset state so we know that we must start a new session */ if (garmin_data_p->state != STATE_RESET) garmin_data_p->state = STATE_DISCONNECTED; - - mutex_unlock(&port->serial->disc_mutex); } @@ -1018,14 +1004,11 @@ static int garmin_write_bulk(struct usb_serial_port *port, spin_unlock_irqrestore(&garmin_data_p->lock, flags); buffer = kmalloc(count, GFP_ATOMIC); - if (!buffer) { - dev_err(&port->dev, "out of memory\n"); + if (!buffer) return -ENOMEM; - } urb = usb_alloc_urb(0, GFP_ATOMIC); if (!urb) { - dev_err(&port->dev, "no more free urbs\n"); kfree(buffer); return -ENOMEM; } @@ -1160,7 +1143,7 @@ static void garmin_read_process(struct garmin_data *garmin_data_p, unsigned long flags; if (garmin_data_p->flags & FLAGS_DROP_DATA) { - /* abort-transfer cmd is actice */ + /* abort-transfer cmd is active */ dev_dbg(&garmin_data_p->port->dev, "%s - pkt dropped\n", __func__); } else if (garmin_data_p->state != STATE_DISCONNECTED && garmin_data_p->state != STATE_RESET) { @@ -1193,17 +1176,11 @@ static void garmin_read_bulk_callback(struct urb *urb) { unsigned long flags; struct usb_serial_port *port = urb->context; - struct usb_serial *serial = port->serial; struct garmin_data *garmin_data_p = usb_get_serial_port_data(port); unsigned char *data = urb->transfer_buffer; int status = urb->status; int retval; - if (!serial) { - dev_dbg(&urb->dev->dev, "%s - bad serial pointer, exiting\n", __func__); - return; - } - if (status) { dev_dbg(&urb->dev->dev, "%s - nonzero read bulk status received: %d\n", __func__, status); @@ -1411,10 +1388,9 @@ static int garmin_port_probe(struct usb_serial_port *port) struct garmin_data *garmin_data_p; garmin_data_p = kzalloc(sizeof(struct garmin_data), GFP_KERNEL); - if (garmin_data_p == NULL) { - dev_err(&port->dev, "%s - Out of memory\n", __func__); + if (!garmin_data_p) return -ENOMEM; - } + init_timer(&garmin_data_p->timer); spin_lock_init(&garmin_data_p->lock); INIT_LIST_HEAD(&garmin_data_p->pktlist); diff --git a/drivers/usb/serial/generic.c b/drivers/usb/serial/generic.c index 2ea70a63199..1bd192290b0 100644 --- a/drivers/usb/serial/generic.c +++ b/drivers/usb/serial/generic.c @@ -1,13 +1,12 @@ /* * USB Serial Converter Generic functions * - * Copyright (C) 2010 - 2011 Johan Hovold (jhovold@gmail.com) + * Copyright (C) 2010 - 2013 Johan Hovold (jhovold@gmail.com) * Copyright (C) 1999 - 2002 Greg Kroah-Hartman (greg@kroah.com) * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License version * 2 as published by the Free Software Foundation. - * */ #include <linux/kernel.h> @@ -37,7 +36,6 @@ MODULE_PARM_DESC(product, "User specified USB idProduct"); static struct usb_device_id generic_device_ids[2]; /* Initially all zeroes. */ -/* All of the device info needed for the Generic Serial Converter */ struct usb_serial_driver usb_serial_generic_device = { .driver = { .owner = THIS_MODULE, @@ -45,8 +43,6 @@ struct usb_serial_driver usb_serial_generic_device = { }, .id_table = generic_device_ids, .num_ports = 1, - .disconnect = usb_serial_generic_disconnect, - .release = usb_serial_generic_release, .throttle = usb_serial_generic_throttle, .unthrottle = usb_serial_generic_unthrottle, .resume = usb_serial_generic_resume, @@ -68,7 +64,6 @@ int usb_serial_generic_register(void) generic_device_ids[0].match_flags = USB_DEVICE_ID_MATCH_VENDOR | USB_DEVICE_ID_MATCH_PRODUCT; - /* register our generic driver with ourselves */ retval = usb_serial_register_drivers(serial_drivers, "usbserial_generic", generic_device_ids); #endif @@ -78,7 +73,6 @@ int usb_serial_generic_register(void) void usb_serial_generic_deregister(void) { #ifdef CONFIG_USB_SERIAL_GENERIC - /* remove our generic driver */ usb_serial_deregister_drivers(serial_drivers); #endif } @@ -88,13 +82,11 @@ int usb_serial_generic_open(struct tty_struct *tty, struct usb_serial_port *port int result = 0; unsigned long flags; - /* clear the throttle flags */ spin_lock_irqsave(&port->lock, flags); port->throttled = 0; port->throttle_req = 0; spin_unlock_irqrestore(&port->lock, flags); - /* if we have a bulk endpoint, start reading from it */ if (port->bulk_in_size) result = usb_serial_generic_submit_read_urbs(port, GFP_KERNEL); @@ -102,32 +94,23 @@ int usb_serial_generic_open(struct tty_struct *tty, struct usb_serial_port *port } EXPORT_SYMBOL_GPL(usb_serial_generic_open); -static void generic_cleanup(struct usb_serial_port *port) +void usb_serial_generic_close(struct usb_serial_port *port) { - struct usb_serial *serial = port->serial; unsigned long flags; int i; - if (serial->dev) { - /* shutdown any bulk transfers that might be going on */ - if (port->bulk_out_size) { - for (i = 0; i < ARRAY_SIZE(port->write_urbs); ++i) - usb_kill_urb(port->write_urbs[i]); + if (port->bulk_out_size) { + for (i = 0; i < ARRAY_SIZE(port->write_urbs); ++i) + usb_kill_urb(port->write_urbs[i]); - spin_lock_irqsave(&port->lock, flags); - kfifo_reset_out(&port->write_fifo); - spin_unlock_irqrestore(&port->lock, flags); - } - if (port->bulk_in_size) { - for (i = 0; i < ARRAY_SIZE(port->read_urbs); ++i) - usb_kill_urb(port->read_urbs[i]); - } + spin_lock_irqsave(&port->lock, flags); + kfifo_reset_out(&port->write_fifo); + spin_unlock_irqrestore(&port->lock, flags); + } + if (port->bulk_in_size) { + for (i = 0; i < ARRAY_SIZE(port->read_urbs); ++i) + usb_kill_urb(port->read_urbs[i]); } -} - -void usb_serial_generic_close(struct usb_serial_port *port) -{ - generic_cleanup(port); } EXPORT_SYMBOL_GPL(usb_serial_generic_close); @@ -138,12 +121,16 @@ int usb_serial_generic_prepare_write_buffer(struct usb_serial_port *port, } /** - * usb_serial_generic_write_start - kick off an URB write - * @port: Pointer to the &struct usb_serial_port data + * usb_serial_generic_write_start - start writing buffered data + * @port: usb-serial port + * @mem_flags: flags to use for memory allocations * - * Returns zero on success, or a negative errno value + * Serialised using USB_SERIAL_WRITE_BUSY flag. + * + * Return: Zero on success or if busy, otherwise a negative errno value. */ -static int usb_serial_generic_write_start(struct usb_serial_port *port) +int usb_serial_generic_write_start(struct usb_serial_port *port, + gfp_t mem_flags) { struct urb *urb; int count, result; @@ -174,7 +161,7 @@ retry: spin_unlock_irqrestore(&port->lock, flags); clear_bit(i, &port->write_urbs_free); - result = usb_submit_urb(urb, GFP_ATOMIC); + result = usb_submit_urb(urb, mem_flags); if (result) { dev_err_console(port, "%s - error submitting urb: %d\n", __func__, result); @@ -187,33 +174,25 @@ retry: return result; } - /* Try sending off another urb, unless in irq context (in which case - * there will be no free urb). */ - if (!in_irq()) - goto retry; - - clear_bit_unlock(USB_SERIAL_WRITE_BUSY, &port->flags); - - return 0; + goto retry; /* try sending off another urb */ } +EXPORT_SYMBOL_GPL(usb_serial_generic_write_start); /** - * usb_serial_generic_write - generic write function for serial USB devices - * @tty: Pointer to &struct tty_struct for the device - * @port: Pointer to the &usb_serial_port structure for the device - * @buf: Pointer to the data to write - * @count: Number of bytes to write + * usb_serial_generic_write - generic write function + * @tty: tty for the port + * @port: usb-serial port + * @buf: data to write + * @count: number of bytes to write * - * Returns the number of characters actually written, which may be anything - * from zero to @count. If an error occurs, it returns the negative errno - * value. + * Return: The number of characters buffered, which may be anything from + * zero to @count, or a negative errno value. */ int usb_serial_generic_write(struct tty_struct *tty, struct usb_serial_port *port, const unsigned char *buf, int count) { int result; - /* only do something if we have a bulk out endpoint */ if (!port->bulk_out_size) return -ENODEV; @@ -221,7 +200,7 @@ int usb_serial_generic_write(struct tty_struct *tty, return 0; count = kfifo_in_locked(&port->write_fifo, buf, count, &port->lock); - result = usb_serial_generic_write_start(port); + result = usb_serial_generic_write_start(port, GFP_ATOMIC); if (result) return result; @@ -264,6 +243,37 @@ int usb_serial_generic_chars_in_buffer(struct tty_struct *tty) } EXPORT_SYMBOL_GPL(usb_serial_generic_chars_in_buffer); +void usb_serial_generic_wait_until_sent(struct tty_struct *tty, long timeout) +{ + struct usb_serial_port *port = tty->driver_data; + unsigned int bps; + unsigned long period; + unsigned long expire; + + bps = tty_get_baud_rate(tty); + if (!bps) + bps = 9600; /* B0 */ + /* + * Use a poll-period of roughly the time it takes to send one + * character or at least one jiffy. + */ + period = max_t(unsigned long, (10 * HZ / bps), 1); + period = min_t(unsigned long, period, timeout); + + dev_dbg(&port->dev, "%s - timeout = %u ms, period = %u ms\n", + __func__, jiffies_to_msecs(timeout), + jiffies_to_msecs(period)); + expire = jiffies + timeout; + while (!port->serial->type->tx_empty(port)) { + schedule_timeout_interruptible(period); + if (signal_pending(current)) + break; + if (time_after(jiffies, expire)) + break; + } +} +EXPORT_SYMBOL_GPL(usb_serial_generic_wait_until_sent); + static int usb_serial_generic_submit_read_urb(struct usb_serial_port *port, int index, gfp_t mem_flags) { @@ -272,8 +282,7 @@ static int usb_serial_generic_submit_read_urb(struct usb_serial_port *port, if (!test_and_clear_bit(index, &port->read_urbs_free)) return 0; - dev_dbg(&port->dev, "%s - port %d, urb %d\n", __func__, - port->number, index); + dev_dbg(&port->dev, "%s - urb %d\n", __func__, index); res = usb_submit_urb(port->read_urbs[index], mem_flags); if (res) { @@ -313,30 +322,25 @@ EXPORT_SYMBOL_GPL(usb_serial_generic_submit_read_urbs); void usb_serial_generic_process_read_urb(struct urb *urb) { struct usb_serial_port *port = urb->context; - struct tty_struct *tty; char *ch = (char *)urb->transfer_buffer; int i; if (!urb->actual_length) return; - - tty = tty_port_tty_get(&port->port); - if (!tty) - return; - - /* The per character mucking around with sysrq path it too slow for - stuff like 3G modems, so shortcircuit it in the 99.9999999% of cases - where the USB serial is not a console anyway */ - if (!port->port.console || !port->sysrq) - tty_insert_flip_string(tty, ch, urb->actual_length); - else { + /* + * The per character mucking around with sysrq path it too slow for + * stuff like 3G modems, so shortcircuit it in the 99.9999999% of + * cases where the USB serial is not a console anyway. + */ + if (!port->port.console || !port->sysrq) { + tty_insert_flip_string(&port->port, ch, urb->actual_length); + } else { for (i = 0; i < urb->actual_length; i++, ch++) { if (!usb_serial_handle_sysrq_char(port, *ch)) - tty_insert_flip_char(tty, *ch, TTY_NORMAL); + tty_insert_flip_char(&port->port, *ch, TTY_NORMAL); } } - tty_flip_buffer_push(tty); - tty_kref_put(tty); + tty_flip_buffer_push(&port->port); } EXPORT_SYMBOL_GPL(usb_serial_generic_process_read_urb); @@ -353,26 +357,40 @@ void usb_serial_generic_read_bulk_callback(struct urb *urb) } set_bit(i, &port->read_urbs_free); - dev_dbg(&port->dev, "%s - port %d, urb %d, len %d\n", - __func__, port->number, i, urb->actual_length); - - if (urb->status) { - dev_dbg(&port->dev, "%s - non-zero urb status: %d\n", - __func__, urb->status); + dev_dbg(&port->dev, "%s - urb %d, len %d\n", __func__, i, + urb->actual_length); + switch (urb->status) { + case 0: + break; + case -ENOENT: + case -ECONNRESET: + case -ESHUTDOWN: + dev_dbg(&port->dev, "%s - urb stopped: %d\n", + __func__, urb->status); + return; + case -EPIPE: + dev_err(&port->dev, "%s - urb stopped: %d\n", + __func__, urb->status); return; + default: + dev_err(&port->dev, "%s - nonzero urb status: %d\n", + __func__, urb->status); + goto resubmit; } usb_serial_debug_data(&port->dev, __func__, urb->actual_length, data); port->serial->type->process_read_urb(urb); +resubmit: /* Throttle the device if requested by tty */ spin_lock_irqsave(&port->lock, flags); port->throttled = port->throttle_req; if (!port->throttled) { spin_unlock_irqrestore(&port->lock, flags); usb_serial_generic_submit_read_urb(port, i, GFP_ATOMIC); - } else + } else { spin_unlock_irqrestore(&port->lock, flags); + } } EXPORT_SYMBOL_GPL(usb_serial_generic_read_bulk_callback); @@ -380,29 +398,38 @@ void usb_serial_generic_write_bulk_callback(struct urb *urb) { unsigned long flags; struct usb_serial_port *port = urb->context; - int status = urb->status; int i; - for (i = 0; i < ARRAY_SIZE(port->write_urbs); ++i) + for (i = 0; i < ARRAY_SIZE(port->write_urbs); ++i) { if (port->write_urbs[i] == urb) break; - + } spin_lock_irqsave(&port->lock, flags); port->tx_bytes -= urb->transfer_buffer_length; set_bit(i, &port->write_urbs_free); spin_unlock_irqrestore(&port->lock, flags); - if (status) { - dev_dbg(&port->dev, "%s - non-zero urb status: %d\n", - __func__, status); - - spin_lock_irqsave(&port->lock, flags); - kfifo_reset_out(&port->write_fifo); - spin_unlock_irqrestore(&port->lock, flags); - } else { - usb_serial_generic_write_start(port); + switch (urb->status) { + case 0: + break; + case -ENOENT: + case -ECONNRESET: + case -ESHUTDOWN: + dev_dbg(&port->dev, "%s - urb stopped: %d\n", + __func__, urb->status); + return; + case -EPIPE: + dev_err_console(port, "%s - urb stopped: %d\n", + __func__, urb->status); + return; + default: + dev_err_console(port, "%s - nonzero urb status: %d\n", + __func__, urb->status); + goto resubmit; } +resubmit: + usb_serial_generic_write_start(port, GFP_ATOMIC); usb_serial_port_softint(port); } EXPORT_SYMBOL_GPL(usb_serial_generic_write_bulk_callback); @@ -412,8 +439,6 @@ void usb_serial_generic_throttle(struct tty_struct *tty) struct usb_serial_port *port = tty->driver_data; unsigned long flags; - /* Set the throttle request flag. It will be picked up - * by usb_serial_generic_read_bulk_callback(). */ spin_lock_irqsave(&port->lock, flags); port->throttle_req = 1; spin_unlock_irqrestore(&port->lock, flags); @@ -425,7 +450,6 @@ void usb_serial_generic_unthrottle(struct tty_struct *tty) struct usb_serial_port *port = tty->driver_data; int was_throttled; - /* Clear the throttle flags */ spin_lock_irq(&port->lock); was_throttled = port->throttled; port->throttled = port->throttle_req = 0; @@ -436,6 +460,82 @@ void usb_serial_generic_unthrottle(struct tty_struct *tty) } EXPORT_SYMBOL_GPL(usb_serial_generic_unthrottle); +static bool usb_serial_generic_msr_changed(struct tty_struct *tty, + unsigned long arg, struct async_icount *cprev) +{ + struct usb_serial_port *port = tty->driver_data; + struct async_icount cnow; + unsigned long flags; + bool ret; + + /* + * Use tty-port initialised flag to detect all hangups including the + * one generated at USB-device disconnect. + */ + if (!test_bit(ASYNCB_INITIALIZED, &port->port.flags)) + return true; + + spin_lock_irqsave(&port->lock, flags); + cnow = port->icount; /* atomic copy*/ + spin_unlock_irqrestore(&port->lock, flags); + + ret = ((arg & TIOCM_RNG) && (cnow.rng != cprev->rng)) || + ((arg & TIOCM_DSR) && (cnow.dsr != cprev->dsr)) || + ((arg & TIOCM_CD) && (cnow.dcd != cprev->dcd)) || + ((arg & TIOCM_CTS) && (cnow.cts != cprev->cts)); + + *cprev = cnow; + + return ret; +} + +int usb_serial_generic_tiocmiwait(struct tty_struct *tty, unsigned long arg) +{ + struct usb_serial_port *port = tty->driver_data; + struct async_icount cnow; + unsigned long flags; + int ret; + + spin_lock_irqsave(&port->lock, flags); + cnow = port->icount; /* atomic copy */ + spin_unlock_irqrestore(&port->lock, flags); + + ret = wait_event_interruptible(port->port.delta_msr_wait, + usb_serial_generic_msr_changed(tty, arg, &cnow)); + if (!ret && !test_bit(ASYNCB_INITIALIZED, &port->port.flags)) + ret = -EIO; + + return ret; +} +EXPORT_SYMBOL_GPL(usb_serial_generic_tiocmiwait); + +int usb_serial_generic_get_icount(struct tty_struct *tty, + struct serial_icounter_struct *icount) +{ + struct usb_serial_port *port = tty->driver_data; + struct async_icount cnow; + unsigned long flags; + + spin_lock_irqsave(&port->lock, flags); + cnow = port->icount; /* atomic copy */ + spin_unlock_irqrestore(&port->lock, flags); + + icount->cts = cnow.cts; + icount->dsr = cnow.dsr; + icount->rng = cnow.rng; + icount->dcd = cnow.dcd; + icount->tx = cnow.tx; + icount->rx = cnow.rx; + icount->frame = cnow.frame; + icount->parity = cnow.parity; + icount->overrun = cnow.overrun; + icount->brk = cnow.brk; + icount->buf_overrun = cnow.buf_overrun; + + return 0; +} +EXPORT_SYMBOL_GPL(usb_serial_generic_get_icount); + #ifdef CONFIG_MAGIC_SYSRQ int usb_serial_handle_sysrq_char(struct usb_serial_port *port, unsigned int ch) { @@ -469,18 +569,27 @@ int usb_serial_handle_break(struct usb_serial_port *port) EXPORT_SYMBOL_GPL(usb_serial_handle_break); /** - * usb_serial_handle_dcd_change - handle a change of carrier detect state - * @port: usb_serial_port structure for the open port - * @tty: tty_struct structure for the port - * @status: new carrier detect status, nonzero if active + * usb_serial_handle_dcd_change - handle a change of carrier detect state + * @port: usb-serial port + * @tty: tty for the port + * @status: new carrier detect status, nonzero if active */ void usb_serial_handle_dcd_change(struct usb_serial_port *usb_port, struct tty_struct *tty, unsigned int status) { struct tty_port *port = &usb_port->port; - dev_dbg(&usb_port->dev, "%s - port %d, status %d\n", __func__, - usb_port->number, status); + dev_dbg(&usb_port->dev, "%s - status %d\n", __func__, status); + + if (tty) { + struct tty_ldisc *ld = tty_ldisc_ref(tty); + + if (ld) { + if (ld->ops->dcd_change) + ld->ops->dcd_change(tty, status); + tty_ldisc_deref(ld); + } + } if (status) wake_up_interruptible(&port->open_wait); @@ -507,7 +616,7 @@ int usb_serial_generic_resume(struct usb_serial *serial) } if (port->bulk_out_size) { - r = usb_serial_generic_write_start(port); + r = usb_serial_generic_write_start(port, GFP_NOIO); if (r < 0) c++; } @@ -516,17 +625,3 @@ int usb_serial_generic_resume(struct usb_serial *serial) return c ? -EIO : 0; } EXPORT_SYMBOL_GPL(usb_serial_generic_resume); - -void usb_serial_generic_disconnect(struct usb_serial *serial) -{ - int i; - - /* stop reads and writes on all ports */ - for (i = 0; i < serial->num_ports; ++i) - generic_cleanup(serial->port[i]); -} -EXPORT_SYMBOL_GPL(usb_serial_generic_disconnect); - -void usb_serial_generic_release(struct usb_serial *serial) -{ -} diff --git a/drivers/usb/serial/hp4x.c b/drivers/usb/serial/hp4x.c deleted file mode 100644 index 2cba60d90c7..00000000000 --- a/drivers/usb/serial/hp4x.c +++ /dev/null @@ -1,51 +0,0 @@ -/* - * HP4x Calculators Serial USB driver - * - * Copyright (C) 2005 Arthur Huillet (ahuillet@users.sf.net) - * Copyright (C) 2001-2005 Greg Kroah-Hartman (greg@kroah.com) - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * See Documentation/usb/usb-serial.txt for more information on using this - * driver - */ - -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/tty.h> -#include <linux/module.h> -#include <linux/usb.h> -#include <linux/usb/serial.h> - -#define DRIVER_DESC "HP4x (48/49) Generic Serial driver" - -#define HP_VENDOR_ID 0x03f0 -#define HP49GP_PRODUCT_ID 0x0121 - -static const struct usb_device_id id_table[] = { - { USB_DEVICE(HP_VENDOR_ID, HP49GP_PRODUCT_ID) }, - { } /* Terminating entry */ -}; - -MODULE_DEVICE_TABLE(usb, id_table); - -static struct usb_serial_driver hp49gp_device = { - .driver = { - .owner = THIS_MODULE, - .name = "hp4X", - }, - .id_table = id_table, - .num_ports = 1, -}; - -static struct usb_serial_driver * const serial_drivers[] = { - &hp49gp_device, NULL -}; - -module_usb_serial_driver(serial_drivers, id_table); - -MODULE_DESCRIPTION(DRIVER_DESC); -MODULE_LICENSE("GPL"); diff --git a/drivers/usb/serial/io_edgeport.c b/drivers/usb/serial/io_edgeport.c index 7b770c7f8b1..c0866971db2 100644 --- a/drivers/usb/serial/io_edgeport.c +++ b/drivers/usb/serial/io_edgeport.c @@ -32,7 +32,6 @@ #include <linux/kernel.h> #include <linux/jiffies.h> #include <linux/errno.h> -#include <linux/init.h> #include <linux/slab.h> #include <linux/tty.h> #include <linux/tty_driver.h> @@ -56,9 +55,7 @@ #define MAX_NAME_LEN 64 -#define CHASE_TIMEOUT (5*HZ) /* 5 seconds */ #define OPEN_TIMEOUT (5*HZ) /* 5 seconds */ -#define COMMAND_TIMEOUT (5*HZ) /* 5 seconds */ /* receive port state */ enum RXSTATE { @@ -110,9 +107,7 @@ struct edgeport_port { wait_queue_head_t wait_chase; /* for handling sleeping while waiting for chase to finish */ wait_queue_head_t wait_open; /* for handling sleeping while waiting for open to finish */ wait_queue_head_t wait_command; /* for handling sleeping while waiting for command to finish */ - wait_queue_head_t delta_msr_wait; /* for handling sleeping while waiting for msr change to happen */ - struct async_icount icount; struct usb_serial_port *port; /* loop back to the owner of this object */ }; @@ -216,8 +211,6 @@ static void edge_break(struct tty_struct *tty, int break_state); static int edge_tiocmget(struct tty_struct *tty); static int edge_tiocmset(struct tty_struct *tty, unsigned int set, unsigned int clear); -static int edge_get_icount(struct tty_struct *tty, - struct serial_icounter_struct *icount); static int edge_startup(struct usb_serial *serial); static void edge_disconnect(struct usb_serial *serial); static void edge_release(struct usb_serial *serial); @@ -232,8 +225,8 @@ static void process_rcvd_data(struct edgeport_serial *edge_serial, unsigned char *buffer, __u16 bufferLength); static void process_rcvd_status(struct edgeport_serial *edge_serial, __u8 byte2, __u8 byte3); -static void edge_tty_recv(struct device *dev, struct tty_struct *tty, - unsigned char *data, int length); +static void edge_tty_recv(struct usb_serial_port *port, unsigned char *data, + int length); static void handle_new_msr(struct edgeport_port *edge_port, __u8 newMsr); static void handle_new_lsr(struct edgeport_port *edge_port, __u8 lsrData, __u8 lsr, __u8 data); @@ -565,7 +558,6 @@ static void edge_interrupt_callback(struct urb *urb) struct device *dev; struct edgeport_port *edge_port; struct usb_serial_port *port; - struct tty_struct *tty; unsigned char *data = urb->transfer_buffer; int length = urb->actual_length; int bytes_avail; @@ -644,12 +636,7 @@ static void edge_interrupt_callback(struct urb *urb) /* tell the tty driver that something has changed */ - tty = tty_port_tty_get( - &edge_port->port->port); - if (tty) { - tty_wakeup(tty); - tty_kref_put(tty); - } + tty_port_tty_wakeup(&edge_port->port->port); /* Since we have more credit, check if more data can be sent */ send_more_port_data(edge_serial, @@ -738,7 +725,6 @@ static void edge_bulk_in_callback(struct urb *urb) static void edge_bulk_out_data_callback(struct urb *urb) { struct edgeport_port *edge_port = urb->context; - struct tty_struct *tty; int status = urb->status; if (status) { @@ -747,14 +733,8 @@ static void edge_bulk_out_data_callback(struct urb *urb) __func__, status); } - tty = tty_port_tty_get(&edge_port->port->port); - - if (tty && edge_port->open) { - /* let the tty driver wakeup if it has a special - write_wakeup function */ - tty_wakeup(tty); - } - tty_kref_put(tty); + if (edge_port->open) + tty_port_tty_wakeup(&edge_port->port->port); /* Release the Write URB */ edge_port->write_in_progress = false; @@ -773,7 +753,6 @@ static void edge_bulk_out_data_callback(struct urb *urb) static void edge_bulk_out_cmd_callback(struct urb *urb) { struct edgeport_port *edge_port = urb->context; - struct tty_struct *tty; int status = urb->status; atomic_dec(&CmdUrbs); @@ -794,13 +773,9 @@ static void edge_bulk_out_cmd_callback(struct urb *urb) return; } - /* Get pointer to tty */ - tty = tty_port_tty_get(&edge_port->port->port); - /* tell the tty driver that something has changed */ - if (tty && edge_port->open) - tty_wakeup(tty); - tty_kref_put(tty); + if (edge_port->open) + tty_port_tty_wakeup(&edge_port->port->port); /* we have completed the command */ edge_port->commandPending = false; @@ -884,12 +859,8 @@ static int edge_open(struct tty_struct *tty, struct usb_serial_port *port) /* initialize our wait queues */ init_waitqueue_head(&edge_port->wait_open); init_waitqueue_head(&edge_port->wait_chase); - init_waitqueue_head(&edge_port->delta_msr_wait); init_waitqueue_head(&edge_port->wait_command); - /* initialize our icount structure */ - memset(&(edge_port->icount), 0x00, sizeof(edge_port->icount)); - /* initialize our port settings */ edge_port->txCredits = 0; /* Can't send any data yet */ /* Must always set this bit to enable ints! */ @@ -926,7 +897,6 @@ static int edge_open(struct tty_struct *tty, struct usb_serial_port *port) edge_port->txfifo.fifo = kmalloc(edge_port->maxTxCredits, GFP_KERNEL); if (!edge_port->txfifo.fifo) { - dev_dbg(dev, "%s - no memory\n", __func__); edge_close(port); return -ENOMEM; } @@ -936,13 +906,12 @@ static int edge_open(struct tty_struct *tty, struct usb_serial_port *port) edge_port->write_in_progress = false; if (!edge_port->write_urb) { - dev_dbg(dev, "%s - no memory\n", __func__); edge_close(port); return -ENOMEM; } - dev_dbg(dev, "%s(%d) - Initialize TX fifo to %d bytes\n", - __func__, port->number, edge_port->maxTxCredits); + dev_dbg(dev, "%s - Initialize TX fifo to %d bytes\n", + __func__, edge_port->maxTxCredits); return 0; } @@ -1148,9 +1117,8 @@ static int edge_write(struct tty_struct *tty, struct usb_serial_port *port, copySize = min((unsigned int)count, (edge_port->txCredits - fifo->count)); - dev_dbg(&port->dev, "%s(%d) of %d byte(s) Fifo room %d -- will copy %d bytes\n", - __func__, port->number, count, - edge_port->txCredits - fifo->count, copySize); + dev_dbg(&port->dev, "%s of %d byte(s) Fifo room %d -- will copy %d bytes\n", + __func__, count, edge_port->txCredits - fifo->count, copySize); /* catch writes of 0 bytes which the tty driver likes to give us, and when txCredits is empty */ @@ -1242,9 +1210,8 @@ static void send_more_port_data(struct edgeport_serial *edge_serial, if (edge_port->write_in_progress || !edge_port->open || (fifo->count == 0)) { - dev_dbg(dev, "%s(%d) EXIT - fifo %d, PendingWrite = %d\n", - __func__, edge_port->port->number, - fifo->count, edge_port->write_in_progress); + dev_dbg(dev, "%s EXIT - fifo %d, PendingWrite = %d\n", + __func__, fifo->count, edge_port->write_in_progress); goto exit_send; } @@ -1256,9 +1223,8 @@ static void send_more_port_data(struct edgeport_serial *edge_serial, * it's better to wait for more credits so we can do a larger write. */ if (edge_port->txCredits < EDGE_FW_GET_TX_CREDITS_SEND_THRESHOLD(edge_port->maxTxCredits, EDGE_FW_BULK_MAX_PACKET_SIZE)) { - dev_dbg(dev, "%s(%d) Not enough credit - fifo %d TxCredit %d\n", - __func__, edge_port->port->number, fifo->count, - edge_port->txCredits); + dev_dbg(dev, "%s Not enough credit - fifo %d TxCredit %d\n", + __func__, fifo->count, edge_port->txCredits); goto exit_send; } @@ -1276,16 +1242,12 @@ static void send_more_port_data(struct edgeport_serial *edge_serial, to send out */ count = fifo->count; buffer = kmalloc(count+2, GFP_ATOMIC); - if (buffer == NULL) { - dev_err_console(edge_port->port, - "%s - no more kernel memory...\n", __func__); + if (!buffer) { edge_port->write_in_progress = false; goto exit_send; } - buffer[0] = IOSP_BUILD_DATA_HDR1(edge_port->port->number - - edge_port->port->serial->minor, count); - buffer[1] = IOSP_BUILD_DATA_HDR2(edge_port->port->number - - edge_port->port->serial->minor, count); + buffer[0] = IOSP_BUILD_DATA_HDR1(edge_port->port->port_number, count); + buffer[1] = IOSP_BUILD_DATA_HDR2(edge_port->port->port_number, count); /* now copy our data */ bytesleft = fifo->size - fifo->tail; @@ -1316,7 +1278,7 @@ static void send_more_port_data(struct edgeport_serial *edge_serial, /* decrement the number of credits we have by the number we just sent */ edge_port->txCredits -= count; - edge_port->icount.tx += count; + edge_port->port->icount.tx += count; status = usb_submit_urb(urb, GFP_ATOMIC); if (status) { @@ -1328,7 +1290,7 @@ static void send_more_port_data(struct edgeport_serial *edge_serial, /* revert the credits as something bad happened. */ edge_port->txCredits += count; - edge_port->icount.tx -= count; + edge_port->port->icount.tx -= count; } dev_dbg(dev, "%s wrote %d byte(s) TxCredit %d, Fifo %d\n", __func__, count, edge_port->txCredits, fifo->count); @@ -1403,8 +1365,7 @@ static int edge_chars_in_buffer(struct tty_struct *tty) edge_port->txfifo.count; spin_unlock_irqrestore(&edge_port->ep_lock, flags); if (num_chars) { - dev_dbg(&port->dev, "%s(port %d) - returns %d\n", __func__, - port->number, num_chars); + dev_dbg(&port->dev, "%s - returns %d\n", __func__, num_chars); } return num_chars; @@ -1590,31 +1551,6 @@ static int edge_tiocmget(struct tty_struct *tty) return result; } -static int edge_get_icount(struct tty_struct *tty, - struct serial_icounter_struct *icount) -{ - struct usb_serial_port *port = tty->driver_data; - struct edgeport_port *edge_port = usb_get_serial_port_data(port); - struct async_icount cnow; - cnow = edge_port->icount; - - icount->cts = cnow.cts; - icount->dsr = cnow.dsr; - icount->rng = cnow.rng; - icount->dcd = cnow.dcd; - icount->rx = cnow.rx; - icount->tx = cnow.tx; - icount->frame = cnow.frame; - icount->overrun = cnow.overrun; - icount->parity = cnow.parity; - icount->brk = cnow.brk; - icount->buf_overrun = cnow.buf_overrun; - - dev_dbg(&port->dev, "%s (%d) TIOCGICOUNT RX=%d, TX=%d\n", __func__, - port->number, icount->rx, icount->tx); - return 0; -} - static int get_serial_info(struct edgeport_port *edge_port, struct serial_struct __user *retinfo) { @@ -1626,8 +1562,8 @@ static int get_serial_info(struct edgeport_port *edge_port, memset(&tmp, 0, sizeof(tmp)); tmp.type = PORT_16550A; - tmp.line = edge_port->port->serial->minor; - tmp.port = edge_port->port->number; + tmp.line = edge_port->port->minor; + tmp.port = edge_port->port->port_number; tmp.irq = 0; tmp.flags = ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ; tmp.xmit_fifo_size = edge_port->maxTxCredits; @@ -1651,46 +1587,15 @@ static int edge_ioctl(struct tty_struct *tty, struct usb_serial_port *port = tty->driver_data; DEFINE_WAIT(wait); struct edgeport_port *edge_port = usb_get_serial_port_data(port); - struct async_icount cnow; - struct async_icount cprev; - - dev_dbg(&port->dev, "%s - port %d, cmd = 0x%x\n", __func__, port->number, cmd); switch (cmd) { case TIOCSERGETLSR: - dev_dbg(&port->dev, "%s (%d) TIOCSERGETLSR\n", __func__, port->number); + dev_dbg(&port->dev, "%s TIOCSERGETLSR\n", __func__); return get_lsr_info(edge_port, (unsigned int __user *) arg); case TIOCGSERIAL: - dev_dbg(&port->dev, "%s (%d) TIOCGSERIAL\n", __func__, port->number); + dev_dbg(&port->dev, "%s TIOCGSERIAL\n", __func__); return get_serial_info(edge_port, (struct serial_struct __user *) arg); - - case TIOCMIWAIT: - dev_dbg(&port->dev, "%s (%d) TIOCMIWAIT\n", __func__, port->number); - cprev = edge_port->icount; - while (1) { - prepare_to_wait(&edge_port->delta_msr_wait, - &wait, TASK_INTERRUPTIBLE); - schedule(); - finish_wait(&edge_port->delta_msr_wait, &wait); - /* see if a signal did it */ - if (signal_pending(current)) - return -ERESTARTSYS; - cnow = edge_port->icount; - if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr && - cnow.dcd == cprev.dcd && cnow.cts == cprev.cts) - return -EIO; /* no change => error */ - if (((arg & TIOCM_RNG) && (cnow.rng != cprev.rng)) || - ((arg & TIOCM_DSR) && (cnow.dsr != cprev.dsr)) || - ((arg & TIOCM_CD) && (cnow.dcd != cprev.dcd)) || - ((arg & TIOCM_CTS) && (cnow.cts != cprev.cts))) { - return 0; - } - cprev = cnow; - } - /* NOTREACHED */ - break; - } return -ENOIOCTLCMD; } @@ -1752,7 +1657,6 @@ static void process_rcvd_data(struct edgeport_serial *edge_serial, struct device *dev = &edge_serial->serial->dev->dev; struct usb_serial_port *port; struct edgeport_port *edge_port; - struct tty_struct *tty; __u16 lastBufferLength; __u16 rxLen; @@ -1860,15 +1764,12 @@ static void process_rcvd_data(struct edgeport_serial *edge_serial, edge_serial->rxPort]; edge_port = usb_get_serial_port_data(port); if (edge_port->open) { - tty = tty_port_tty_get( - &edge_port->port->port); - if (tty) { - dev_dbg(dev, "%s - Sending %d bytes to TTY for port %d\n", - __func__, rxLen, edge_serial->rxPort); - edge_tty_recv(&edge_serial->serial->dev->dev, tty, buffer, rxLen); - tty_kref_put(tty); - } - edge_port->icount.rx += rxLen; + dev_dbg(dev, "%s - Sending %d bytes to TTY for port %d\n", + __func__, rxLen, + edge_serial->rxPort); + edge_tty_recv(edge_port->port, buffer, + rxLen); + edge_port->port->icount.rx += rxLen; } buffer += rxLen; } @@ -2017,20 +1918,20 @@ static void process_rcvd_status(struct edgeport_serial *edge_serial, * edge_tty_recv * this function passes data on to the tty flip buffer *****************************************************************************/ -static void edge_tty_recv(struct device *dev, struct tty_struct *tty, - unsigned char *data, int length) +static void edge_tty_recv(struct usb_serial_port *port, unsigned char *data, + int length) { int cnt; - cnt = tty_insert_flip_string(tty, data, length); + cnt = tty_insert_flip_string(&port->port, data, length); if (cnt < length) { - dev_err(dev, "%s - dropping data, %d bytes lost\n", + dev_err(&port->dev, "%s - dropping data, %d bytes lost\n", __func__, length - cnt); } data += cnt; length -= cnt; - tty_flip_buffer_push(tty); + tty_flip_buffer_push(&port->port); } @@ -2044,7 +1945,7 @@ static void handle_new_msr(struct edgeport_port *edge_port, __u8 newMsr) if (newMsr & (EDGEPORT_MSR_DELTA_CTS | EDGEPORT_MSR_DELTA_DSR | EDGEPORT_MSR_DELTA_RI | EDGEPORT_MSR_DELTA_CD)) { - icount = &edge_port->icount; + icount = &edge_port->port->icount; /* update input line counters */ if (newMsr & EDGEPORT_MSR_DELTA_CTS) @@ -2055,7 +1956,7 @@ static void handle_new_msr(struct edgeport_port *edge_port, __u8 newMsr) icount->dcd++; if (newMsr & EDGEPORT_MSR_DELTA_RI) icount->rng++; - wake_up_interruptible(&edge_port->delta_msr_wait); + wake_up_interruptible(&edge_port->port->port.delta_msr_wait); } /* Save the new modem status */ @@ -2086,16 +1987,11 @@ static void handle_new_lsr(struct edgeport_port *edge_port, __u8 lsrData, } /* Place LSR data byte into Rx buffer */ - if (lsrData) { - struct tty_struct *tty = - tty_port_tty_get(&edge_port->port->port); - if (tty) { - edge_tty_recv(&edge_port->port->dev, tty, &data, 1); - tty_kref_put(tty); - } - } + if (lsrData) + edge_tty_recv(edge_port->port, &data, 1); + /* update input line counters */ - icount = &edge_port->icount; + icount = &edge_port->port->icount; if (newLsr & LSR_BREAK) icount->brk++; if (newLsr & LSR_OVER_ERR) @@ -2124,11 +2020,8 @@ static int sram_write(struct usb_serial *serial, __u16 extAddr, __u16 addr, dev_dbg(&serial->dev->dev, "%s - %x, %x, %d\n", __func__, extAddr, addr, length); transfer_buffer = kmalloc(64, GFP_KERNEL); - if (!transfer_buffer) { - dev_err(&serial->dev->dev, "%s - kmalloc(%d) failed.\n", - __func__, 64); + if (!transfer_buffer) return -ENOMEM; - } /* need to split these writes up into 64 byte chunks */ result = 0; @@ -2172,11 +2065,8 @@ static int rom_write(struct usb_serial *serial, __u16 extAddr, __u16 addr, unsigned char *transfer_buffer; transfer_buffer = kmalloc(64, GFP_KERNEL); - if (!transfer_buffer) { - dev_err(&serial->dev->dev, "%s - kmalloc(%d) failed.\n", - __func__, 64); + if (!transfer_buffer) return -ENOMEM; - } /* need to split these writes up into 64 byte chunks */ result = 0; @@ -2218,11 +2108,8 @@ static int rom_read(struct usb_serial *serial, __u16 extAddr, unsigned char *transfer_buffer; transfer_buffer = kmalloc(64, GFP_KERNEL); - if (!transfer_buffer) { - dev_err(&serial->dev->dev, - "%s - kmalloc(%d) failed.\n", __func__, 64); + if (!transfer_buffer) return -ENOMEM; - } /* need to split these reads up into 64 byte chunks */ result = 0; @@ -2262,17 +2149,13 @@ static int send_iosp_ext_cmd(struct edgeport_port *edge_port, int status = 0; buffer = kmalloc(10, GFP_ATOMIC); - if (!buffer) { - dev_err(&edge_port->port->dev, - "%s - kmalloc(%d) failed.\n", __func__, 10); + if (!buffer) return -ENOMEM; - } currentCommand = buffer; - MAKE_CMD_EXT_CMD(¤tCommand, &length, - edge_port->port->number - edge_port->port->serial->minor, - command, param); + MAKE_CMD_EXT_CMD(¤tCommand, &length, edge_port->port->port_number, + command, param); status = write_cmd_usb(edge_port, buffer, length); if (status) { @@ -2355,18 +2238,16 @@ static int send_cmd_write_baud_rate(struct edgeport_port *edge_port, int cmdLen = 0; int divisor; int status; - unsigned char number = - edge_port->port->number - edge_port->port->serial->minor; + u32 number = edge_port->port->port_number; if (edge_serial->is_epic && !edge_serial->epic_descriptor.Supports.IOSPSetBaudRate) { - dev_dbg(dev, "SendCmdWriteBaudRate - NOT Setting baud rate for port = %d, baud = %d\n", - edge_port->port->number, baudRate); + dev_dbg(dev, "SendCmdWriteBaudRate - NOT Setting baud rate for port, baud = %d\n", + baudRate); return 0; } - dev_dbg(dev, "%s - port = %d, baud = %d\n", __func__, - edge_port->port->number, baudRate); + dev_dbg(dev, "%s - baud = %d\n", __func__, baudRate); status = calc_baud_rate_divisor(dev, baudRate, &divisor); if (status) { @@ -2376,10 +2257,9 @@ static int send_cmd_write_baud_rate(struct edgeport_port *edge_port, /* Alloc memory for the string of commands. */ cmdBuffer = kmalloc(0x100, GFP_ATOMIC); - if (!cmdBuffer) { - dev_err(dev, "%s - kmalloc(%d) failed.\n", __func__, 0x100); + if (!cmdBuffer) return -ENOMEM; - } + currCmd = cmdBuffer; /* Enable access to divisor latch */ @@ -2477,9 +2357,8 @@ static int send_cmd_write_uart_register(struct edgeport_port *edge_port, currCmd = cmdBuffer; /* Build a cmd in the buffer to write the given register */ - MAKE_CMD_WRITE_REG(&currCmd, &cmdLen, - edge_port->port->number - edge_port->port->serial->minor, - regNum, regValue); + MAKE_CMD_WRITE_REG(&currCmd, &cmdLen, edge_port->port->port_number, + regNum, regValue); status = write_cmd_usb(edge_port, cmdBuffer, cmdLen); if (status) { @@ -2513,8 +2392,6 @@ static void change_port_settings(struct tty_struct *tty, __u8 txFlow; int status; - dev_dbg(dev, "%s - port %d\n", __func__, edge_port->port->number); - if (!edge_port->open && !edge_port->openPending) { dev_dbg(dev, "%s - port not opened\n", __func__); @@ -2888,10 +2765,9 @@ static int edge_startup(struct usb_serial *serial) /* create our private serial structure */ edge_serial = kzalloc(sizeof(struct edgeport_serial), GFP_KERNEL); - if (edge_serial == NULL) { - dev_err(&serial->dev->dev, "%s - Out of memory\n", __func__); + if (!edge_serial) return -ENOMEM; - } + spin_lock_init(&edge_serial->es_lock); edge_serial->serial = serial; usb_set_serial_data(serial, edge_serial); @@ -2980,14 +2856,12 @@ static int edge_startup(struct usb_serial *serial) /* not set up yet, so do it now */ edge_serial->interrupt_read_urb = usb_alloc_urb(0, GFP_KERNEL); - if (!edge_serial->interrupt_read_urb) { - dev_err(ddev, "out of memory\n"); + if (!edge_serial->interrupt_read_urb) return -ENOMEM; - } + edge_serial->interrupt_in_buffer = kmalloc(buffer_size, GFP_KERNEL); if (!edge_serial->interrupt_in_buffer) { - dev_err(ddev, "out of memory\n"); usb_free_urb(edge_serial->interrupt_read_urb); return -ENOMEM; } @@ -3017,14 +2891,12 @@ static int edge_startup(struct usb_serial *serial) /* not set up yet, so do it now */ edge_serial->read_urb = usb_alloc_urb(0, GFP_KERNEL); - if (!edge_serial->read_urb) { - dev_err(ddev, "out of memory\n"); + if (!edge_serial->read_urb) return -ENOMEM; - } + edge_serial->bulk_in_buffer = kmalloc(buffer_size, GFP_KERNEL); if (!edge_serial->bulk_in_buffer) { - dev_err(&dev->dev, "out of memory\n"); usb_free_urb(edge_serial->read_urb); return -ENOMEM; } diff --git a/drivers/usb/serial/io_tables.h b/drivers/usb/serial/io_tables.h index 1511dd0ad32..ae5fac5656c 100644 --- a/drivers/usb/serial/io_tables.h +++ b/drivers/usb/serial/io_tables.h @@ -116,7 +116,8 @@ static struct usb_serial_driver edgeport_2port_device = { .set_termios = edge_set_termios, .tiocmget = edge_tiocmget, .tiocmset = edge_tiocmset, - .get_icount = edge_get_icount, + .tiocmiwait = usb_serial_generic_tiocmiwait, + .get_icount = usb_serial_generic_get_icount, .write = edge_write, .write_room = edge_write_room, .chars_in_buffer = edge_chars_in_buffer, @@ -147,7 +148,8 @@ static struct usb_serial_driver edgeport_4port_device = { .set_termios = edge_set_termios, .tiocmget = edge_tiocmget, .tiocmset = edge_tiocmset, - .get_icount = edge_get_icount, + .tiocmiwait = usb_serial_generic_tiocmiwait, + .get_icount = usb_serial_generic_get_icount, .write = edge_write, .write_room = edge_write_room, .chars_in_buffer = edge_chars_in_buffer, @@ -178,7 +180,8 @@ static struct usb_serial_driver edgeport_8port_device = { .set_termios = edge_set_termios, .tiocmget = edge_tiocmget, .tiocmset = edge_tiocmset, - .get_icount = edge_get_icount, + .tiocmiwait = usb_serial_generic_tiocmiwait, + .get_icount = usb_serial_generic_get_icount, .write = edge_write, .write_room = edge_write_room, .chars_in_buffer = edge_chars_in_buffer, @@ -209,7 +212,8 @@ static struct usb_serial_driver epic_device = { .set_termios = edge_set_termios, .tiocmget = edge_tiocmget, .tiocmset = edge_tiocmset, - .get_icount = edge_get_icount, + .tiocmiwait = usb_serial_generic_tiocmiwait, + .get_icount = usb_serial_generic_get_icount, .write = edge_write, .write_room = edge_write_room, .chars_in_buffer = edge_chars_in_buffer, diff --git a/drivers/usb/serial/io_ti.c b/drivers/usb/serial/io_ti.c index 82afc4d6a32..c0a42e9e677 100644 --- a/drivers/usb/serial/io_ti.c +++ b/drivers/usb/serial/io_ti.c @@ -20,7 +20,6 @@ #include <linux/kernel.h> #include <linux/jiffies.h> #include <linux/errno.h> -#include <linux/init.h> #include <linux/slab.h> #include <linux/tty.h> #include <linux/tty_driver.h> @@ -29,6 +28,7 @@ #include <linux/spinlock.h> #include <linux/mutex.h> #include <linux/serial.h> +#include <linux/swab.h> #include <linux/kfifo.h> #include <linux/ioctl.h> #include <linux/firmware.h> @@ -64,8 +64,6 @@ #define EDGE_CLOSING_WAIT 4000 /* in .01 sec */ -#define EDGE_OUT_BUF_SIZE 1024 - /* Product information read from the Edgeport */ struct product_info { @@ -86,17 +84,13 @@ struct edgeport_port { int baud_rate; int close_pending; int lsr_event; - struct async_icount icount; - wait_queue_head_t delta_msr_wait; /* for handling sleeping while - waiting for msr change to - happen */ + struct edgeport_serial *edge_serial; struct usb_serial_port *port; __u8 bUartMode; /* Port type, 0: RS232, etc. */ spinlock_t ep_lock; int ep_read_urb_state; int ep_write_urb_in_use; - struct kfifo write_fifo; }; struct edgeport_serial { @@ -201,15 +195,15 @@ static int closing_wait = EDGE_CLOSING_WAIT; static bool ignore_cpu_rev; static int default_uart_mode; /* RS232 */ -static void edge_tty_recv(struct device *dev, struct tty_struct *tty, - unsigned char *data, int length); +static void edge_tty_recv(struct usb_serial_port *port, unsigned char *data, + int length); static void stop_read(struct edgeport_port *edge_port); static int restart_read(struct edgeport_port *edge_port); static void edge_set_termios(struct tty_struct *tty, struct usb_serial_port *port, struct ktermios *old_termios); -static void edge_send(struct tty_struct *tty); +static void edge_send(struct usb_serial_port *port, struct tty_struct *tty); /* sysfs attributes */ static int edge_create_sysfs_attrs(struct usb_serial_port *port); @@ -262,7 +256,7 @@ static int send_cmd(struct usb_device *dev, __u8 command, /* clear tx/rx buffers and fifo in TI UMP */ static int purge_port(struct usb_serial_port *port, __u16 mask) { - int port_number = port->number - port->serial->minor; + int port_number = port->port_number; dev_dbg(&port->dev, "%s - port %d, mask %x\n", __func__, port_number, mask); @@ -287,7 +281,7 @@ static int read_download_mem(struct usb_device *dev, int start_address, { int status = 0; __u8 read_length; - __be16 be_start_address; + u16 be_start_address; dev_dbg(&dev->dev, "%s - @ %x for %d\n", __func__, start_address, length); @@ -303,10 +297,14 @@ static int read_download_mem(struct usb_device *dev, int start_address, if (read_length > 1) { dev_dbg(&dev->dev, "%s - @ %x for %d\n", __func__, start_address, read_length); } - be_start_address = cpu_to_be16(start_address); + /* + * NOTE: Must use swab as wIndex is sent in little-endian + * byte order regardless of host byte order. + */ + be_start_address = swab16((u16)start_address); status = ti_vread_sync(dev, UMPC_MEMORY_READ, (__u16)address_type, - (__force __u16)be_start_address, + be_start_address, buffer, read_length); if (status) { @@ -370,11 +368,9 @@ static int write_boot_mem(struct edgeport_serial *serial, /* Must do a read before write */ if (!serial->TiReadI2C) { temp = kmalloc(1, GFP_KERNEL); - if (!temp) { - dev_err(&serial->serial->dev->dev, - "%s - out of memory\n", __func__); + if (!temp) return -ENOMEM; - } + status = read_boot_mem(serial, 0, 1, temp); kfree(temp); if (status) @@ -403,7 +399,7 @@ static int write_i2c_mem(struct edgeport_serial *serial, struct device *dev = &serial->serial->dev->dev; int status = 0; int write_length; - __be16 be_start_address; + u16 be_start_address; /* We can only send a maximum of 1 aligned byte page at a time */ @@ -418,11 +414,16 @@ static int write_i2c_mem(struct edgeport_serial *serial, __func__, start_address, write_length); usb_serial_debug_data(dev, __func__, write_length, buffer); - /* Write first page */ - be_start_address = cpu_to_be16(start_address); + /* + * Write first page. + * + * NOTE: Must use swab as wIndex is sent in little-endian byte order + * regardless of host byte order. + */ + be_start_address = swab16((u16)start_address); status = ti_vsend_sync(serial->serial->dev, UMPC_MEMORY_WRITE, (__u16)address_type, - (__force __u16)be_start_address, + be_start_address, buffer, write_length); if (status) { dev_dbg(dev, "%s - ERROR %d\n", __func__, status); @@ -445,11 +446,16 @@ static int write_i2c_mem(struct edgeport_serial *serial, __func__, start_address, write_length); usb_serial_debug_data(dev, __func__, write_length, buffer); - /* Write next page */ - be_start_address = cpu_to_be16(start_address); + /* + * Write next page. + * + * NOTE: Must use swab as wIndex is sent in little-endian byte + * order regardless of host byte order. + */ + be_start_address = swab16((u16)start_address); status = ti_vsend_sync(serial->serial->dev, UMPC_MEMORY_WRITE, (__u16)address_type, - (__force __u16)be_start_address, + be_start_address, buffer, write_length); if (status) { dev_err(dev, "%s - ERROR %d\n", __func__, status); @@ -477,10 +483,8 @@ static int tx_active(struct edgeport_port *port) int bytes_left = 0; oedb = kmalloc(sizeof(*oedb), GFP_KERNEL); - if (!oedb) { - dev_err(&port->port->dev, "%s - out of memory\n", __func__); + if (!oedb) return -ENOMEM; - } lsr = kmalloc(1, GFP_KERNEL); /* Sigh, that's right, just one byte, as not all platforms can do DMA @@ -521,65 +525,6 @@ exit_is_tx_active: return bytes_left; } -static void chase_port(struct edgeport_port *port, unsigned long timeout, - int flush) -{ - int baud_rate; - struct tty_struct *tty = tty_port_tty_get(&port->port->port); - struct usb_serial *serial = port->port->serial; - wait_queue_t wait; - unsigned long flags; - - if (!tty) - return; - - if (!timeout) - timeout = (HZ * EDGE_CLOSING_WAIT)/100; - - /* wait for data to drain from the buffer */ - spin_lock_irqsave(&port->ep_lock, flags); - init_waitqueue_entry(&wait, current); - add_wait_queue(&tty->write_wait, &wait); - for (;;) { - set_current_state(TASK_INTERRUPTIBLE); - if (kfifo_len(&port->write_fifo) == 0 - || timeout == 0 || signal_pending(current) - || serial->disconnected) - /* disconnect */ - break; - spin_unlock_irqrestore(&port->ep_lock, flags); - timeout = schedule_timeout(timeout); - spin_lock_irqsave(&port->ep_lock, flags); - } - set_current_state(TASK_RUNNING); - remove_wait_queue(&tty->write_wait, &wait); - if (flush) - kfifo_reset_out(&port->write_fifo); - spin_unlock_irqrestore(&port->ep_lock, flags); - tty_kref_put(tty); - - /* wait for data to drain from the device */ - timeout += jiffies; - while ((long)(jiffies - timeout) < 0 && !signal_pending(current) - && !serial->disconnected) { - /* not disconnected */ - if (!tx_active(port)) - break; - msleep(10); - } - - /* disconnected */ - if (serial->disconnected) - return; - - /* wait one more character time, based on baud rate */ - /* (tx_active doesn't seem to wait for the last byte) */ - baud_rate = port->baud_rate; - if (baud_rate == 0) - baud_rate = 50; - msleep(max(1, DIV_ROUND_UP(10000, baud_rate))); -} - static int choose_config(struct usb_device *dev) { /* @@ -655,8 +600,8 @@ static int get_descriptor_addr(struct edgeport_serial *serial, if (rom_desc->Type == desc_type) return start_address; - start_address = start_address + sizeof(struct ti_i2c_desc) - + rom_desc->Size; + start_address = start_address + sizeof(struct ti_i2c_desc) + + le16_to_cpu(rom_desc->Size); } while ((start_address < TI_MAX_I2C_SIZE) && rom_desc->Type); @@ -669,7 +614,7 @@ static int valid_csum(struct ti_i2c_desc *rom_desc, __u8 *buffer) __u16 i; __u8 cs = 0; - for (i = 0; i < rom_desc->Size; i++) + for (i = 0; i < le16_to_cpu(rom_desc->Size); i++) cs = (__u8)(cs + buffer[i]); if (cs != rom_desc->CheckSum) { @@ -690,14 +635,11 @@ static int check_i2c_image(struct edgeport_serial *serial) __u16 ttype; rom_desc = kmalloc(sizeof(*rom_desc), GFP_KERNEL); - if (!rom_desc) { - dev_err(dev, "%s - out of memory\n", __func__); + if (!rom_desc) return -ENOMEM; - } + buffer = kmalloc(TI_MAX_I2C_SIZE, GFP_KERNEL); if (!buffer) { - dev_err(dev, "%s - out of memory when allocating buffer\n", - __func__); kfree(rom_desc); return -ENOMEM; } @@ -723,7 +665,7 @@ static int check_i2c_image(struct edgeport_serial *serial) break; if ((start_address + sizeof(struct ti_i2c_desc) + - rom_desc->Size) > TI_MAX_I2C_SIZE) { + le16_to_cpu(rom_desc->Size)) > TI_MAX_I2C_SIZE) { status = -ENODEV; dev_dbg(dev, "%s - structure too big, erroring out.\n", __func__); break; @@ -738,7 +680,8 @@ static int check_i2c_image(struct edgeport_serial *serial) /* Read the descriptor data */ status = read_rom(serial, start_address + sizeof(struct ti_i2c_desc), - rom_desc->Size, buffer); + le16_to_cpu(rom_desc->Size), + buffer); if (status) break; @@ -747,7 +690,7 @@ static int check_i2c_image(struct edgeport_serial *serial) break; } start_address = start_address + sizeof(struct ti_i2c_desc) + - rom_desc->Size; + le16_to_cpu(rom_desc->Size); } while ((rom_desc->Type != I2C_DESC_TYPE_ION) && (start_address < TI_MAX_I2C_SIZE)); @@ -771,10 +714,9 @@ static int get_manuf_info(struct edgeport_serial *serial, __u8 *buffer) struct device *dev = &serial->serial->dev->dev; rom_desc = kmalloc(sizeof(*rom_desc), GFP_KERNEL); - if (!rom_desc) { - dev_err(dev, "%s - out of memory\n", __func__); + if (!rom_desc) return -ENOMEM; - } + start_address = get_descriptor_addr(serial, I2C_DESC_TYPE_ION, rom_desc); @@ -786,7 +728,7 @@ static int get_manuf_info(struct edgeport_serial *serial, __u8 *buffer) /* Read the descriptor data */ status = read_rom(serial, start_address+sizeof(struct ti_i2c_desc), - rom_desc->Size, buffer); + le16_to_cpu(rom_desc->Size), buffer); if (status) goto exit; @@ -834,10 +776,8 @@ static int build_i2c_fw_hdr(__u8 *header, struct device *dev) sizeof(struct ti_i2c_firmware_rec)); buffer = kmalloc(buffer_size, GFP_KERNEL); - if (!buffer) { - dev_err(dev, "%s - out of memory\n", __func__); + if (!buffer) return -ENOMEM; - } // Set entire image of 0xffs memset(buffer, 0xff, buffer_size); @@ -881,7 +821,7 @@ static int build_i2c_fw_hdr(__u8 *header, struct device *dev) firmware_rec = (struct ti_i2c_firmware_rec*)i2c_header->Data; i2c_header->Type = I2C_DESC_TYPE_FIRMWARE_BLANK; - i2c_header->Size = (__u16)buffer_size; + i2c_header->Size = cpu_to_le16(buffer_size); i2c_header->CheckSum = cs; firmware_rec->Ver_Major = OperationalMajorVersion; firmware_rec->Ver_Minor = OperationalMinorVersion; @@ -897,10 +837,8 @@ static int i2c_type_bootmode(struct edgeport_serial *serial) u8 *data; data = kmalloc(1, GFP_KERNEL); - if (!data) { - dev_err(dev, "%s - out of memory\n", __func__); + if (!data) return -ENOMEM; - } /* Try to read type 2 */ status = ti_vread_sync(serial->serial->dev, UMPC_MEMORY_READ, @@ -1051,10 +989,9 @@ static int download_fw(struct edgeport_serial *serial) * Read Manufacturing Descriptor from TI Based Edgeport */ ti_manuf_desc = kmalloc(sizeof(*ti_manuf_desc), GFP_KERNEL); - if (!ti_manuf_desc) { - dev_err(dev, "%s - out of memory.\n", __func__); + if (!ti_manuf_desc) return -ENOMEM; - } + status = get_manuf_info(serial, (__u8 *)ti_manuf_desc); if (status) { kfree(ti_manuf_desc); @@ -1071,7 +1008,6 @@ static int download_fw(struct edgeport_serial *serial) rom_desc = kmalloc(sizeof(*rom_desc), GFP_KERNEL); if (!rom_desc) { - dev_err(dev, "%s - out of memory.\n", __func__); kfree(ti_manuf_desc); return -ENOMEM; } @@ -1088,7 +1024,6 @@ static int download_fw(struct edgeport_serial *serial) firmware_version = kmalloc(sizeof(*firmware_version), GFP_KERNEL); if (!firmware_version) { - dev_err(dev, "%s - out of memory.\n", __func__); kfree(rom_desc); kfree(ti_manuf_desc); return -ENOMEM; @@ -1133,8 +1068,6 @@ static int download_fw(struct edgeport_serial *serial) record = kmalloc(1, GFP_KERNEL); if (!record) { - dev_err(dev, "%s - out of memory.\n", - __func__); kfree(firmware_version); kfree(rom_desc); kfree(ti_manuf_desc); @@ -1218,7 +1151,6 @@ static int download_fw(struct edgeport_serial *serial) header = kmalloc(HEADER_SIZE, GFP_KERNEL); if (!header) { - dev_err(dev, "%s - out of memory.\n", __func__); kfree(rom_desc); kfree(ti_manuf_desc); return -ENOMEM; @@ -1226,7 +1158,6 @@ static int download_fw(struct edgeport_serial *serial) vheader = kmalloc(HEADER_SIZE, GFP_KERNEL); if (!vheader) { - dev_err(dev, "%s - out of memory.\n", __func__); kfree(header); kfree(rom_desc); kfree(ti_manuf_desc); @@ -1355,10 +1286,9 @@ static int download_fw(struct edgeport_serial *serial) * Read Manufacturing Descriptor from TI Based Edgeport */ ti_manuf_desc = kmalloc(sizeof(*ti_manuf_desc), GFP_KERNEL); - if (!ti_manuf_desc) { - dev_err(dev, "%s - out of memory.\n", __func__); + if (!ti_manuf_desc) return -ENOMEM; - } + status = get_manuf_info(serial, (__u8 *)ti_manuf_desc); if (status) { kfree(ti_manuf_desc); @@ -1393,10 +1323,8 @@ static int download_fw(struct edgeport_serial *serial) buffer_size = (((1024 * 16) - 512) + sizeof(struct ti_i2c_image_header)); buffer = kmalloc(buffer_size, GFP_KERNEL); - if (!buffer) { - dev_err(dev, "%s - out of memory\n", __func__); + if (!buffer) return -ENOMEM; - } /* Initialize the buffer to 0xff (pad the buffer) */ memset(buffer, 0xff, buffer_size); @@ -1454,7 +1382,8 @@ stayinbootmode: static int ti_do_config(struct edgeport_port *port, int feature, int on) { - int port_number = port->port->number - port->port->serial->minor; + int port_number = port->port->port_number; + on = !!on; /* 1 or 0 not bitmask */ return send_cmd(port->port->serial->dev, feature, (__u8)(UMPM_UART1_PORT + port_number), @@ -1507,7 +1436,7 @@ static void handle_new_msr(struct edgeport_port *edge_port, __u8 msr) if (msr & (EDGEPORT_MSR_DELTA_CTS | EDGEPORT_MSR_DELTA_DSR | EDGEPORT_MSR_DELTA_RI | EDGEPORT_MSR_DELTA_CD)) { - icount = &edge_port->icount; + icount = &edge_port->port->icount; /* update input line counters */ if (msr & EDGEPORT_MSR_DELTA_CTS) @@ -1518,7 +1447,7 @@ static void handle_new_msr(struct edgeport_port *edge_port, __u8 msr) icount->dcd++; if (msr & EDGEPORT_MSR_DELTA_RI) icount->rng++; - wake_up_interruptible(&edge_port->delta_msr_wait); + wake_up_interruptible(&edge_port->port->port.delta_msr_wait); } /* Save the new modem status */ @@ -1543,7 +1472,6 @@ static void handle_new_lsr(struct edgeport_port *edge_port, int lsr_data, struct async_icount *icount; __u8 new_lsr = (__u8)(lsr & (__u8)(LSR_OVER_ERR | LSR_PAR_ERR | LSR_FRM_ERR | LSR_BREAK)); - struct tty_struct *tty; dev_dbg(&edge_port->port->dev, "%s - %02x\n", __func__, new_lsr); @@ -1557,16 +1485,11 @@ static void handle_new_lsr(struct edgeport_port *edge_port, int lsr_data, new_lsr &= (__u8)(LSR_OVER_ERR | LSR_BREAK); /* Place LSR data byte into Rx buffer */ - if (lsr_data) { - tty = tty_port_tty_get(&edge_port->port->port); - if (tty) { - edge_tty_recv(&edge_port->port->dev, tty, &data, 1); - tty_kref_put(tty); - } - } + if (lsr_data) + edge_tty_recv(edge_port->port, &data, 1); /* update input line counters */ - icount = &edge_port->icount; + icount = &edge_port->port->icount; if (new_lsr & LSR_BREAK) icount->brk++; if (new_lsr & LSR_OVER_ERR) @@ -1679,7 +1602,6 @@ static void edge_bulk_in_callback(struct urb *urb) struct edgeport_port *edge_port = urb->context; struct device *dev = &edge_port->port->dev; unsigned char *data = urb->transfer_buffer; - struct tty_struct *tty; int retval = 0; int port_number; int status = urb->status; @@ -1706,7 +1628,7 @@ static void edge_bulk_in_callback(struct urb *urb) return; } - port_number = edge_port->port->number - edge_port->port->serial->minor; + port_number = edge_port->port->port_number; if (edge_port->lsr_event) { edge_port->lsr_event = 0; @@ -1718,17 +1640,16 @@ static void edge_bulk_in_callback(struct urb *urb) ++data; } - tty = tty_port_tty_get(&edge_port->port->port); - if (tty && urb->actual_length) { + if (urb->actual_length) { usb_serial_debug_data(dev, __func__, urb->actual_length, data); if (edge_port->close_pending) dev_dbg(dev, "%s - close pending, dropping data on the floor\n", __func__); else - edge_tty_recv(dev, tty, data, urb->actual_length); - edge_port->icount.rx += urb->actual_length; + edge_tty_recv(edge_port->port, data, + urb->actual_length); + edge_port->port->icount.rx += urb->actual_length; } - tty_kref_put(tty); exit: /* continue read unless stopped */ @@ -1743,16 +1664,16 @@ exit: dev_err(dev, "%s - usb_submit_urb failed with result %d\n", __func__, retval); } -static void edge_tty_recv(struct device *dev, struct tty_struct *tty, - unsigned char *data, int length) +static void edge_tty_recv(struct usb_serial_port *port, unsigned char *data, + int length) { int queued; - queued = tty_insert_flip_string(tty, data, length); + queued = tty_insert_flip_string(&port->port, data, length); if (queued < length) - dev_err(dev, "%s - dropping data, %d bytes lost\n", + dev_err(&port->dev, "%s - dropping data, %d bytes lost\n", __func__, length - queued); - tty_flip_buffer_push(tty); + tty_flip_buffer_push(&port->port); } static void edge_bulk_out_callback(struct urb *urb) @@ -1782,7 +1703,7 @@ static void edge_bulk_out_callback(struct urb *urb) /* send any buffered data */ tty = tty_port_tty_get(&port->port); - edge_send(tty); + edge_send(port, tty); tty_kref_put(tty); } @@ -1800,29 +1721,10 @@ static int edge_open(struct tty_struct *tty, struct usb_serial_port *port) if (edge_port == NULL) return -ENODEV; - port_number = port->number - port->serial->minor; - switch (port_number) { - case 0: - edge_port->uart_base = UMPMEM_BASE_UART1; - edge_port->dma_address = UMPD_OEDB1_ADDRESS; - break; - case 1: - edge_port->uart_base = UMPMEM_BASE_UART2; - edge_port->dma_address = UMPD_OEDB2_ADDRESS; - break; - default: - dev_err(&port->dev, "Unknown port number!!!\n"); - return -ENODEV; - } - - dev_dbg(&port->dev, "%s - port_number = %d, uart_base = %04x, dma_address = %04x\n", - __func__, port_number, edge_port->uart_base, edge_port->dma_address); + port_number = port->port_number; dev = port->serial->dev; - memset(&(edge_port->icount), 0x00, sizeof(edge_port->icount)); - init_waitqueue_head(&edge_port->delta_msr_wait); - /* turn off loopback */ status = ti_do_config(edge_port, UMPC_SET_CLR_LOOPBACK, 0); if (status) { @@ -1959,6 +1861,7 @@ static void edge_close(struct usb_serial_port *port) struct edgeport_serial *edge_serial; struct edgeport_port *edge_port; struct usb_serial *serial = port->serial; + unsigned long flags; int port_number; edge_serial = usb_get_serial_data(port->serial); @@ -1970,28 +1873,17 @@ static void edge_close(struct usb_serial_port *port) * this flag and dump add read data */ edge_port->close_pending = 1; - /* chase the port close and flush */ - chase_port(edge_port, (HZ * closing_wait) / 100, 1); - usb_kill_urb(port->read_urb); usb_kill_urb(port->write_urb); edge_port->ep_write_urb_in_use = 0; + spin_lock_irqsave(&edge_port->ep_lock, flags); + kfifo_reset_out(&port->write_fifo); + spin_unlock_irqrestore(&edge_port->ep_lock, flags); - /* assuming we can still talk to the device, - * send a close port command to it */ dev_dbg(&port->dev, "%s - send umpc_close_port\n", __func__); - port_number = port->number - port->serial->minor; - - mutex_lock(&serial->disc_mutex); - if (!serial->disconnected) { - send_cmd(serial->dev, - UMPC_CLOSE_PORT, - (__u8)(UMPM_UART1_PORT + port_number), - 0, - NULL, - 0); - } - mutex_unlock(&serial->disc_mutex); + port_number = port->port_number; + send_cmd(serial->dev, UMPC_CLOSE_PORT, + (__u8)(UMPM_UART1_PORT + port_number), 0, NULL, 0); mutex_lock(&edge_serial->es_lock); --edge_port->edge_serial->num_ports_open; @@ -2019,16 +1911,15 @@ static int edge_write(struct tty_struct *tty, struct usb_serial_port *port, if (edge_port->close_pending == 1) return -ENODEV; - count = kfifo_in_locked(&edge_port->write_fifo, data, count, + count = kfifo_in_locked(&port->write_fifo, data, count, &edge_port->ep_lock); - edge_send(tty); + edge_send(port, tty); return count; } -static void edge_send(struct tty_struct *tty) +static void edge_send(struct usb_serial_port *port, struct tty_struct *tty) { - struct usb_serial_port *port = tty->driver_data; int count, result; struct edgeport_port *edge_port = usb_get_serial_port_data(port); unsigned long flags; @@ -2040,7 +1931,7 @@ static void edge_send(struct tty_struct *tty) return; } - count = kfifo_out(&edge_port->write_fifo, + count = kfifo_out(&port->write_fifo, port->write_urb->transfer_buffer, port->bulk_out_size); @@ -2067,7 +1958,7 @@ static void edge_send(struct tty_struct *tty) edge_port->ep_write_urb_in_use = 0; /* TODO: reschedule edge_send */ } else - edge_port->icount.tx += count; + edge_port->port->icount.tx += count; /* wakeup any process waiting for writes to complete */ /* there is now more room in the buffer for new writes */ @@ -2088,7 +1979,7 @@ static int edge_write_room(struct tty_struct *tty) return 0; spin_lock_irqsave(&edge_port->ep_lock, flags); - room = kfifo_avail(&edge_port->write_fifo); + room = kfifo_avail(&port->write_fifo); spin_unlock_irqrestore(&edge_port->ep_lock, flags); dev_dbg(&port->dev, "%s - returns %d\n", __func__, room); @@ -2101,20 +1992,29 @@ static int edge_chars_in_buffer(struct tty_struct *tty) struct edgeport_port *edge_port = usb_get_serial_port_data(port); int chars = 0; unsigned long flags; - if (edge_port == NULL) return 0; - if (edge_port->close_pending == 1) - return 0; spin_lock_irqsave(&edge_port->ep_lock, flags); - chars = kfifo_len(&edge_port->write_fifo); + chars = kfifo_len(&port->write_fifo); spin_unlock_irqrestore(&edge_port->ep_lock, flags); dev_dbg(&port->dev, "%s - returns %d\n", __func__, chars); return chars; } +static bool edge_tx_empty(struct usb_serial_port *port) +{ + struct edgeport_port *edge_port = usb_get_serial_port_data(port); + int ret; + + ret = tx_active(edge_port); + if (ret > 0) + return false; + + return true; +} + static void edge_throttle(struct tty_struct *tty) { struct usb_serial_port *port = tty->driver_data; @@ -2210,15 +2110,11 @@ static void change_port_settings(struct tty_struct *tty, int baud; unsigned cflag; int status; - int port_number = edge_port->port->number - - edge_port->port->serial->minor; - - dev_dbg(dev, "%s - port %d\n", __func__, edge_port->port->number); + int port_number = edge_port->port->port_number; config = kmalloc (sizeof (*config), GFP_KERNEL); if (!config) { tty->termios = *old_termios; - dev_err(dev, "%s - out of memory\n", __func__); return; } @@ -2357,7 +2253,6 @@ static void edge_set_termios(struct tty_struct *tty, tty->termios.c_cflag, tty->termios.c_iflag); dev_dbg(&port->dev, "%s - old clfag %08x old iflag %08x\n", __func__, old_termios->c_cflag, old_termios->c_iflag); - dev_dbg(&port->dev, "%s - port %d\n", __func__, port->number); if (edge_port == NULL) return; @@ -2423,46 +2318,30 @@ static int edge_tiocmget(struct tty_struct *tty) return result; } -static int edge_get_icount(struct tty_struct *tty, - struct serial_icounter_struct *icount) -{ - struct usb_serial_port *port = tty->driver_data; - struct edgeport_port *edge_port = usb_get_serial_port_data(port); - struct async_icount *ic = &edge_port->icount; - - icount->cts = ic->cts; - icount->dsr = ic->dsr; - icount->rng = ic->rng; - icount->dcd = ic->dcd; - icount->tx = ic->tx; - icount->rx = ic->rx; - icount->frame = ic->frame; - icount->parity = ic->parity; - icount->overrun = ic->overrun; - icount->brk = ic->brk; - icount->buf_overrun = ic->buf_overrun; - return 0; -} - static int get_serial_info(struct edgeport_port *edge_port, struct serial_struct __user *retinfo) { struct serial_struct tmp; + unsigned cwait; if (!retinfo) return -EFAULT; + cwait = edge_port->port->port.closing_wait; + if (cwait != ASYNC_CLOSING_WAIT_NONE) + cwait = jiffies_to_msecs(cwait) / 10; + memset(&tmp, 0, sizeof(tmp)); tmp.type = PORT_16550A; - tmp.line = edge_port->port->serial->minor; - tmp.port = edge_port->port->number; + tmp.line = edge_port->port->minor; + tmp.port = edge_port->port->port_number; tmp.irq = 0; tmp.flags = ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ; tmp.xmit_fifo_size = edge_port->port->bulk_out_size; tmp.baud_base = 9600; tmp.close_delay = 5*HZ; - tmp.closing_wait = closing_wait; + tmp.closing_wait = cwait; if (copy_to_user(retinfo, &tmp, sizeof(*retinfo))) return -EFAULT; @@ -2474,38 +2353,12 @@ static int edge_ioctl(struct tty_struct *tty, { struct usb_serial_port *port = tty->driver_data; struct edgeport_port *edge_port = usb_get_serial_port_data(port); - struct async_icount cnow; - struct async_icount cprev; - - dev_dbg(&port->dev, "%s - port %d, cmd = 0x%x\n", __func__, port->number, cmd); switch (cmd) { case TIOCGSERIAL: dev_dbg(&port->dev, "%s - TIOCGSERIAL\n", __func__); return get_serial_info(edge_port, (struct serial_struct __user *) arg); - case TIOCMIWAIT: - dev_dbg(&port->dev, "%s - TIOCMIWAIT\n", __func__); - cprev = edge_port->icount; - while (1) { - interruptible_sleep_on(&edge_port->delta_msr_wait); - /* see if a signal did it */ - if (signal_pending(current)) - return -ERESTARTSYS; - cnow = edge_port->icount; - if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr && - cnow.dcd == cprev.dcd && cnow.cts == cprev.cts) - return -EIO; /* no change => error */ - if (((arg & TIOCM_RNG) && (cnow.rng != cprev.rng)) || - ((arg & TIOCM_DSR) && (cnow.dsr != cprev.dsr)) || - ((arg & TIOCM_CD) && (cnow.dcd != cprev.dcd)) || - ((arg & TIOCM_CTS) && (cnow.cts != cprev.cts))) { - return 0; - } - cprev = cnow; - } - /* not reached */ - break; } return -ENOIOCTLCMD; } @@ -2517,9 +2370,6 @@ static void edge_break(struct tty_struct *tty, int break_state) int status; int bv = 0; /* Off */ - /* chase the port close */ - chase_port(edge_port, 0, 0); - if (break_state == -1) bv = 1; /* On */ status = ti_do_config(edge_port, UMPC_SET_CLR_BREAK, bv); @@ -2535,10 +2385,9 @@ static int edge_startup(struct usb_serial *serial) /* create our private serial structure */ edge_serial = kzalloc(sizeof(struct edgeport_serial), GFP_KERNEL); - if (edge_serial == NULL) { - dev_err(&serial->dev->dev, "%s - Out of memory\n", __func__); + if (!edge_serial) return -ENOMEM; - } + mutex_init(&edge_serial->es_lock); edge_serial->serial = serial; usb_set_serial_data(serial, edge_serial); @@ -2570,28 +2419,45 @@ static int edge_port_probe(struct usb_serial_port *port) if (!edge_port) return -ENOMEM; - ret = kfifo_alloc(&edge_port->write_fifo, EDGE_OUT_BUF_SIZE, - GFP_KERNEL); - if (ret) { - kfree(edge_port); - return -ENOMEM; - } - spin_lock_init(&edge_port->ep_lock); edge_port->port = port; edge_port->edge_serial = usb_get_serial_data(port->serial); edge_port->bUartMode = default_uart_mode; + switch (port->port_number) { + case 0: + edge_port->uart_base = UMPMEM_BASE_UART1; + edge_port->dma_address = UMPD_OEDB1_ADDRESS; + break; + case 1: + edge_port->uart_base = UMPMEM_BASE_UART2; + edge_port->dma_address = UMPD_OEDB2_ADDRESS; + break; + default: + dev_err(&port->dev, "unknown port number\n"); + ret = -ENODEV; + goto err; + } + + dev_dbg(&port->dev, + "%s - port_number = %d, uart_base = %04x, dma_address = %04x\n", + __func__, port->port_number, edge_port->uart_base, + edge_port->dma_address); + usb_set_serial_port_data(port, edge_port); ret = edge_create_sysfs_attrs(port); - if (ret) { - kfifo_free(&edge_port->write_fifo); - kfree(edge_port); - return ret; - } + if (ret) + goto err; + + port->port.closing_wait = msecs_to_jiffies(closing_wait * 10); + port->port.drain_delay = 1; return 0; +err: + kfree(edge_port); + + return ret; } static int edge_port_remove(struct usb_serial_port *port) @@ -2599,9 +2465,7 @@ static int edge_port_remove(struct usb_serial_port *port) struct edgeport_port *edge_port; edge_port = usb_get_serial_port_data(port); - edge_remove_sysfs_attrs(port); - kfifo_free(&edge_port->write_fifo); kfree(edge_port); return 0; @@ -2609,7 +2473,7 @@ static int edge_port_remove(struct usb_serial_port *port) /* Sysfs Attributes */ -static ssize_t show_uart_mode(struct device *dev, +static ssize_t uart_mode_show(struct device *dev, struct device_attribute *attr, char *buf) { struct usb_serial_port *port = to_usb_serial_port(dev); @@ -2618,7 +2482,7 @@ static ssize_t show_uart_mode(struct device *dev, return sprintf(buf, "%d\n", edge_port->bUartMode); } -static ssize_t store_uart_mode(struct device *dev, +static ssize_t uart_mode_store(struct device *dev, struct device_attribute *attr, const char *valbuf, size_t count) { struct usb_serial_port *port = to_usb_serial_port(dev); @@ -2634,9 +2498,7 @@ static ssize_t store_uart_mode(struct device *dev, return count; } - -static DEVICE_ATTR(uart_mode, S_IWUSR | S_IRUGO, show_uart_mode, - store_uart_mode); +static DEVICE_ATTR_RW(uart_mode); static int edge_create_sysfs_attrs(struct usb_serial_port *port) { @@ -2671,10 +2533,12 @@ static struct usb_serial_driver edgeport_1port_device = { .set_termios = edge_set_termios, .tiocmget = edge_tiocmget, .tiocmset = edge_tiocmset, - .get_icount = edge_get_icount, + .tiocmiwait = usb_serial_generic_tiocmiwait, + .get_icount = usb_serial_generic_get_icount, .write = edge_write, .write_room = edge_write_room, .chars_in_buffer = edge_chars_in_buffer, + .tx_empty = edge_tx_empty, .break_ctl = edge_break, .read_int_callback = edge_interrupt_callback, .read_bulk_callback = edge_bulk_in_callback, @@ -2702,9 +2566,12 @@ static struct usb_serial_driver edgeport_2port_device = { .set_termios = edge_set_termios, .tiocmget = edge_tiocmget, .tiocmset = edge_tiocmset, + .tiocmiwait = usb_serial_generic_tiocmiwait, + .get_icount = usb_serial_generic_get_icount, .write = edge_write, .write_room = edge_write_room, .chars_in_buffer = edge_chars_in_buffer, + .tx_empty = edge_tx_empty, .break_ctl = edge_break, .read_int_callback = edge_interrupt_callback, .read_bulk_callback = edge_bulk_in_callback, diff --git a/drivers/usb/serial/io_usbvend.h b/drivers/usb/serial/io_usbvend.h index 51f83fbb73b..6f6a856bc37 100644 --- a/drivers/usb/serial/io_usbvend.h +++ b/drivers/usb/serial/io_usbvend.h @@ -594,7 +594,7 @@ struct edge_boot_descriptor { struct ti_i2c_desc { __u8 Type; // Type of descriptor - __u16 Size; // Size of data only not including header + __le16 Size; // Size of data only not including header __u8 CheckSum; // Checksum (8 bit sum of data only) __u8 Data[0]; // Data starts here } __attribute__((packed)); diff --git a/drivers/usb/serial/ipaq.c b/drivers/usb/serial/ipaq.c index 76c9a847da5..f51a5d52c0e 100644 --- a/drivers/usb/serial/ipaq.c +++ b/drivers/usb/serial/ipaq.c @@ -12,7 +12,6 @@ #include <linux/kernel.h> #include <linux/errno.h> -#include <linux/init.h> #include <linux/slab.h> #include <linux/tty.h> #include <linux/tty_driver.h> @@ -37,7 +36,7 @@ static int ipaq_open(struct tty_struct *tty, static int ipaq_calc_num_ports(struct usb_serial *serial); static int ipaq_startup(struct usb_serial *serial); -static struct usb_device_id ipaq_id_table [] = { +static const struct usb_device_id ipaq_id_table[] = { { USB_DEVICE(0x0104, 0x00BE) }, /* Socket USB Sync */ { USB_DEVICE(0x03F0, 0x1016) }, /* HP USB Sync */ { USB_DEVICE(0x03F0, 0x1116) }, /* HP USB Sync 1611 */ diff --git a/drivers/usb/serial/ipw.c b/drivers/usb/serial/ipw.c index 155eab14b30..8b1cf18a668 100644 --- a/drivers/usb/serial/ipw.c +++ b/drivers/usb/serial/ipw.c @@ -38,7 +38,6 @@ #include <linux/kernel.h> #include <linux/errno.h> -#include <linux/init.h> #include <linux/slab.h> #include <linux/tty.h> #include <linux/tty_flip.h> diff --git a/drivers/usb/serial/ir-usb.c b/drivers/usb/serial/ir-usb.c index e24e2d4f4c1..73956d48a0c 100644 --- a/drivers/usb/serial/ir-usb.c +++ b/drivers/usb/serial/ir-usb.c @@ -287,7 +287,6 @@ static void ir_process_read_urb(struct urb *urb) { struct usb_serial_port *port = urb->context; unsigned char *data = urb->transfer_buffer; - struct tty_struct *tty; if (!urb->actual_length) return; @@ -302,12 +301,8 @@ static void ir_process_read_urb(struct urb *urb) if (urb->actual_length == 1) return; - tty = tty_port_tty_get(&port->port); - if (!tty) - return; - tty_insert_flip_string(tty, data + 1, urb->actual_length - 1); - tty_flip_buffer_push(tty); - tty_kref_put(tty); + tty_insert_flip_string(&port->port, data + 1, urb->actual_length - 1); + tty_flip_buffer_push(&port->port); } static void ir_set_termios_callback(struct urb *urb) @@ -382,15 +377,12 @@ static void ir_set_termios(struct tty_struct *tty, * send the baud change out on an "empty" data packet */ urb = usb_alloc_urb(0, GFP_KERNEL); - if (!urb) { - dev_err(&port->dev, "%s - no more urbs\n", __func__); + if (!urb) return; - } + transfer_buffer = kmalloc(1, GFP_KERNEL); - if (!transfer_buffer) { - dev_err(&port->dev, "%s - out of memory\n", __func__); + if (!transfer_buffer) goto err_buf; - } *transfer_buffer = ir_xbof | ir_baud; diff --git a/drivers/usb/serial/iuu_phoenix.c b/drivers/usb/serial/iuu_phoenix.c index 1e1fbed65ef..5ad4a0fb4b2 100644 --- a/drivers/usb/serial/iuu_phoenix.c +++ b/drivers/usb/serial/iuu_phoenix.c @@ -17,7 +17,6 @@ */ #include <linux/kernel.h> #include <linux/errno.h> -#include <linux/init.h> #include <linux/slab.h> #include <linux/tty.h> #include <linux/tty_driver.h> @@ -55,7 +54,6 @@ static void read_rxcmd_callback(struct urb *urb); struct iuu_private { spinlock_t lock; /* store irq state */ - wait_queue_head_t delta_msr_wait; u8 line_status; int tiostatus; /* store IUART SIGNAL for tiocmget call */ u8 reset; /* if 1 reset is needed */ @@ -94,7 +92,6 @@ static int iuu_port_probe(struct usb_serial_port *port) priv->vcc = vcc_default; spin_lock_init(&priv->lock); - init_waitqueue_head(&priv->delta_msr_wait); usb_set_serial_port_data(port, priv); @@ -289,7 +286,7 @@ static int bulk_immediate(struct usb_serial_port *port, u8 *buf, u8 count) usb_bulk_msg(serial->dev, usb_sndbulkpipe(serial->dev, port->bulk_out_endpointAddress), buf, - count, &actual, HZ * 1); + count, &actual, 1000); if (status != IUU_OPERATION_OK) dev_dbg(&port->dev, "%s - error = %2x\n", __func__, status); @@ -309,7 +306,7 @@ static int read_immediate(struct usb_serial_port *port, u8 *buf, u8 count) usb_bulk_msg(serial->dev, usb_rcvbulkpipe(serial->dev, port->bulk_in_endpointAddress), buf, - count, &actual, HZ * 1); + count, &actual, 1000); if (status != IUU_OPERATION_OK) dev_dbg(&port->dev, "%s - error = %2x\n", __func__, status); @@ -581,7 +578,6 @@ static void read_buf_callback(struct urb *urb) { struct usb_serial_port *port = urb->context; unsigned char *data = urb->transfer_buffer; - struct tty_struct *tty; int status = urb->status; if (status) { @@ -592,14 +588,12 @@ static void read_buf_callback(struct urb *urb) } dev_dbg(&port->dev, "%s - %i chars to write\n", __func__, urb->actual_length); - tty = tty_port_tty_get(&port->port); if (data == NULL) dev_dbg(&port->dev, "%s - data is NULL !!!\n", __func__); - if (tty && urb->actual_length && data) { - tty_insert_flip_string(tty, data, urb->actual_length); - tty_flip_buffer_push(tty); + if (urb->actual_length && data) { + tty_insert_flip_string(&port->port, data, urb->actual_length); + tty_flip_buffer_push(&port->port); } - tty_kref_put(tty); iuu_led_activity_on(urb); } @@ -775,7 +769,7 @@ uart_enable_failed: return status; } -/* Diables the IUU UART (a.k.a. the Phoenix voiderface) */ +/* Disables the IUU UART (a.k.a. the Phoenix voiderface) */ static int iuu_uart_off(struct usb_serial_port *port) { int status; @@ -947,22 +941,13 @@ static void iuu_set_termios(struct tty_struct *tty, static void iuu_close(struct usb_serial_port *port) { /* iuu_led (port,255,0,0,0); */ - struct usb_serial *serial; - - serial = port->serial; - if (!serial) - return; iuu_uart_off(port); - if (serial->dev) { - /* free writebuf */ - /* shutdown our urbs */ - dev_dbg(&port->dev, "%s - shutting down urbs\n", __func__); - usb_kill_urb(port->write_urb); - usb_kill_urb(port->read_urb); - usb_kill_urb(port->interrupt_in_urb); - iuu_led(port, 0, 0, 0xF000, 0xFF); - } + + usb_kill_urb(port->write_urb); + usb_kill_urb(port->read_urb); + + iuu_led(port, 0, 0, 0xF000, 0xFF); } static void iuu_init_termios(struct tty_struct *tty) @@ -1144,7 +1129,7 @@ static int iuu_vcc_set(struct usb_serial_port *port, unsigned int vcc) * Sysfs Attributes */ -static ssize_t show_vcc_mode(struct device *dev, +static ssize_t vcc_mode_show(struct device *dev, struct device_attribute *attr, char *buf) { struct usb_serial_port *port = to_usb_serial_port(dev); @@ -1153,7 +1138,7 @@ static ssize_t show_vcc_mode(struct device *dev, return sprintf(buf, "%d\n", priv->vcc); } -static ssize_t store_vcc_mode(struct device *dev, +static ssize_t vcc_mode_store(struct device *dev, struct device_attribute *attr, const char *buf, size_t count) { struct usb_serial_port *port = to_usb_serial_port(dev); @@ -1166,7 +1151,7 @@ static ssize_t store_vcc_mode(struct device *dev, goto fail_store_vcc_mode; } - dev_dbg(dev, "%s: setting vcc_mode = %ld", __func__, v); + dev_dbg(dev, "%s: setting vcc_mode = %ld\n", __func__, v); if ((v != 3) && (v != 5)) { dev_err(dev, "%s - vcc_mode %ld is invalid\n", __func__, v); @@ -1177,9 +1162,7 @@ static ssize_t store_vcc_mode(struct device *dev, fail_store_vcc_mode: return count; } - -static DEVICE_ATTR(vcc_mode, S_IRUSR | S_IWUSR, show_vcc_mode, - store_vcc_mode); +static DEVICE_ATTR_RW(vcc_mode); static int iuu_create_sysfs_attrs(struct usb_serial_port *port) { diff --git a/drivers/usb/serial/keyspan.c b/drivers/usb/serial/keyspan.c index 97bc49f68ef..93cb7cebda6 100644 --- a/drivers/usb/serial/keyspan.c +++ b/drivers/usb/serial/keyspan.c @@ -31,7 +31,6 @@ #include <linux/kernel.h> #include <linux/jiffies.h> #include <linux/errno.h> -#include <linux/init.h> #include <linux/slab.h> #include <linux/tty.h> #include <linux/tty_driver.h> @@ -50,23 +49,27 @@ #define INSTAT_BUFLEN 32 #define GLOCONT_BUFLEN 64 #define INDAT49W_BUFLEN 512 +#define IN_BUFLEN 64 +#define OUT_BUFLEN 64 +#define INACK_BUFLEN 1 +#define OUTCONT_BUFLEN 64 /* Per device and per port private data */ struct keyspan_serial_private { const struct keyspan_device_details *device_details; struct urb *instat_urb; - char instat_buf[INSTAT_BUFLEN]; + char *instat_buf; /* added to support 49wg, where data from all 4 ports comes in on 1 EP and high-speed supported */ struct urb *indat_urb; - char indat_buf[INDAT49W_BUFLEN]; + char *indat_buf; /* XXX this one probably will need a lock */ struct urb *glocont_urb; - char glocont_buf[GLOCONT_BUFLEN]; - char ctrl_buf[8]; /* for EP0 control message */ + char *glocont_buf; + char *ctrl_buf; /* for EP0 control message */ }; struct keyspan_port_private { @@ -81,18 +84,18 @@ struct keyspan_port_private { /* Input endpoints and buffer for this port */ struct urb *in_urbs[2]; - char in_buffer[2][64]; + char *in_buffer[2]; /* Output endpoints and buffer for this port */ struct urb *out_urbs[2]; - char out_buffer[2][64]; + char *out_buffer[2]; /* Input ack endpoint */ struct urb *inack_urb; - char inack_buffer[1]; + char *inack_buffer; /* Output control endpoint */ struct urb *outcont_urb; - char outcont_buffer[64]; + char *outcont_buffer; /* Settings for the port */ int baud; @@ -152,7 +155,7 @@ static void keyspan_set_termios(struct tty_struct *tty, p_priv = usb_get_serial_port_data(port); d_details = p_priv->device_details; cflag = tty->termios.c_cflag; - device_port = port->number - port->serial->minor; + device_port = port->port_number; /* Baud rate calculation takes baud rate as an integer so other rates can be generated if desired. */ @@ -161,7 +164,7 @@ static void keyspan_set_termios(struct tty_struct *tty, if (d_details->calculate_baud_rate(port, baud_rate, d_details->baudclk, NULL, NULL, NULL, device_port) == KEYSPAN_BAUD_RATE_OK) { /* FIXME - more to do here to ensure rate changes cleanly */ - /* FIXME - calcuate exact rate from divisor ? */ + /* FIXME - calculate exact rate from divisor ? */ p_priv->baud = baud_rate; } else baud_rate = tty_termios_baud_rate(old_termios); @@ -234,8 +237,8 @@ static int keyspan_write(struct tty_struct *tty, dataOffset = 1; } - dev_dbg(&port->dev, "%s - for port %d (%d chars), flip=%d\n", - __func__, port->number, count, p_priv->out_flip); + dev_dbg(&port->dev, "%s - %d chars, flip=%d\n", __func__, count, + p_priv->out_flip); for (left = count; left > 0; left -= todo) { todo = left; @@ -291,21 +294,19 @@ static void usa26_indat_callback(struct urb *urb) int i, err; int endpoint; struct usb_serial_port *port; - struct tty_struct *tty; unsigned char *data = urb->transfer_buffer; int status = urb->status; endpoint = usb_pipeendpoint(urb->pipe); if (status) { - dev_dbg(&urb->dev->dev,"%s - nonzero status: %x on endpoint %d.\n", + dev_dbg(&urb->dev->dev, "%s - nonzero status: %x on endpoint %d.\n", __func__, status, endpoint); return; } port = urb->context; - tty = tty_port_tty_get(&port->port); - if (tty && urb->actual_length) { + if (urb->actual_length) { /* 0x80 bit is error flag */ if ((data[0] & 0x80) == 0) { /* no errors on individual bytes, only @@ -315,7 +316,7 @@ static void usa26_indat_callback(struct urb *urb) else err = 0; for (i = 1; i < urb->actual_length ; ++i) - tty_insert_flip_char(tty, data[i], err); + tty_insert_flip_char(&port->port, data[i], err); } else { /* some bytes had errors, every byte has status */ dev_dbg(&port->dev, "%s - RX error!!!!\n", __func__); @@ -328,12 +329,12 @@ static void usa26_indat_callback(struct urb *urb) if (stat & RXERROR_PARITY) flag |= TTY_PARITY; /* XXX should handle break (0x10) */ - tty_insert_flip_char(tty, data[i+1], flag); + tty_insert_flip_char(&port->port, data[i+1], + flag); } } - tty_flip_buffer_push(tty); + tty_flip_buffer_push(&port->port); } - tty_kref_put(tty); /* Resubmit urb so we continue receiving */ err = usb_submit_urb(urb, GFP_ATOMIC); @@ -380,7 +381,6 @@ static void usa26_instat_callback(struct urb *urb) struct usb_serial *serial; struct usb_serial_port *port; struct keyspan_port_private *p_priv; - struct tty_struct *tty; int old_dcd_state, err; int status = urb->status; @@ -397,17 +397,6 @@ static void usa26_instat_callback(struct urb *urb) msg = (struct keyspan_usa26_portStatusMessage *)data; -#if 0 - dev_dbg(&urb->dev->dev, - "%s - port status: port %d cts %d dcd %d dsr %d ri %d toff %d txoff %d rxen %d cr %d", - __func__, msg->port, msg->hskia_cts, msg->gpia_dcd, msg->dsr, - msg->ri, msg->_txOff, msg->_txXoff, msg->rxEnabled, - msg->controlResponse); -#endif - - /* Now do something useful with the data */ - - /* Check port number from message and retrieve private data */ if (msg->port >= serial->num_ports) { dev_dbg(&urb->dev->dev, "%s - Unexpected port number %d\n", __func__, msg->port); @@ -423,12 +412,8 @@ static void usa26_instat_callback(struct urb *urb) p_priv->dcd_state = ((msg->gpia_dcd) ? 1 : 0); p_priv->ri_state = ((msg->ri) ? 1 : 0); - if (old_dcd_state != p_priv->dcd_state) { - tty = tty_port_tty_get(&port->port); - if (tty && !C_CLOCAL(tty)) - tty_hangup(tty); - tty_kref_put(tty); - } + if (old_dcd_state != p_priv->dcd_state) + tty_port_tty_hangup(&port->port, true); /* Resubmit urb so we continue receiving */ err = usb_submit_urb(urb, GFP_ATOMIC); @@ -446,7 +431,6 @@ static void usa28_indat_callback(struct urb *urb) { int err; struct usb_serial_port *port; - struct tty_struct *tty; unsigned char *data; struct keyspan_port_private *p_priv; int status = urb->status; @@ -469,12 +453,11 @@ static void usa28_indat_callback(struct urb *urb) p_priv = usb_get_serial_port_data(port); data = urb->transfer_buffer; - tty = tty_port_tty_get(&port->port); - if (tty && urb->actual_length) { - tty_insert_flip_string(tty, data, urb->actual_length); - tty_flip_buffer_push(tty); + if (urb->actual_length) { + tty_insert_flip_string(&port->port, data, + urb->actual_length); + tty_flip_buffer_push(&port->port); } - tty_kref_put(tty); /* Resubmit urb so we continue receiving */ err = usb_submit_urb(urb, GFP_ATOMIC); @@ -514,7 +497,6 @@ static void usa28_instat_callback(struct urb *urb) struct usb_serial *serial; struct usb_serial_port *port; struct keyspan_port_private *p_priv; - struct tty_struct *tty; int old_dcd_state; int status = urb->status; @@ -530,14 +512,6 @@ static void usa28_instat_callback(struct urb *urb) goto exit; } - /* - dev_dbg(&urb->dev->dev, - "%s %x %x %x %x %x %x %x %x %x %x %x %x", __func__, - data[0], data[1], data[2], data[3], data[4], data[5], - data[6], data[7], data[8], data[9], data[10], data[11]); - */ - - /* Now do something useful with the data */ msg = (struct keyspan_usa28_portStatusMessage *)data; /* Check port number from message and retrieve private data */ @@ -555,12 +529,8 @@ static void usa28_instat_callback(struct urb *urb) p_priv->dcd_state = ((msg->dcd) ? 1 : 0); p_priv->ri_state = ((msg->ri) ? 1 : 0); - if (old_dcd_state != p_priv->dcd_state && old_dcd_state) { - tty = tty_port_tty_get(&port->port); - if (tty && !C_CLOCAL(tty)) - tty_hangup(tty); - tty_kref_put(tty); - } + if (old_dcd_state != p_priv->dcd_state && old_dcd_state) + tty_port_tty_hangup(&port->port, true); /* Resubmit urb so we continue receiving */ err = usb_submit_urb(urb, GFP_ATOMIC); @@ -621,13 +591,6 @@ static void usa49_instat_callback(struct urb *urb) goto exit; } - /* - dev_dbg(&urb->dev->dev, "%s: %x %x %x %x %x %x %x %x %x %x %x", - __func__, data[0], data[1], data[2], data[3], data[4], - data[5], data[6], data[7], data[8], data[9], data[10]); - */ - - /* Now do something useful with the data */ msg = (struct keyspan_usa49_portStatusMessage *)data; /* Check port number from message and retrieve private data */ @@ -646,12 +609,8 @@ static void usa49_instat_callback(struct urb *urb) p_priv->dcd_state = ((msg->dcd) ? 1 : 0); p_priv->ri_state = ((msg->ri) ? 1 : 0); - if (old_dcd_state != p_priv->dcd_state && old_dcd_state) { - struct tty_struct *tty = tty_port_tty_get(&port->port); - if (tty && !C_CLOCAL(tty)) - tty_hangup(tty); - tty_kref_put(tty); - } + if (old_dcd_state != p_priv->dcd_state && old_dcd_state) + tty_port_tty_hangup(&port->port, true); /* Resubmit urb so we continue receiving */ err = usb_submit_urb(urb, GFP_ATOMIC); @@ -669,7 +628,6 @@ static void usa49_indat_callback(struct urb *urb) int i, err; int endpoint; struct usb_serial_port *port; - struct tty_struct *tty; unsigned char *data = urb->transfer_buffer; int status = urb->status; @@ -682,12 +640,11 @@ static void usa49_indat_callback(struct urb *urb) } port = urb->context; - tty = tty_port_tty_get(&port->port); - if (tty && urb->actual_length) { + if (urb->actual_length) { /* 0x80 bit is error flag */ if ((data[0] & 0x80) == 0) { /* no error on any byte */ - tty_insert_flip_string(tty, data + 1, + tty_insert_flip_string(&port->port, data + 1, urb->actual_length - 1); } else { /* some bytes had errors, every byte has status */ @@ -700,12 +657,12 @@ static void usa49_indat_callback(struct urb *urb) if (stat & RXERROR_PARITY) flag |= TTY_PARITY; /* XXX should handle break (0x10) */ - tty_insert_flip_char(tty, data[i+1], flag); + tty_insert_flip_char(&port->port, data[i+1], + flag); } } - tty_flip_buffer_push(tty); + tty_flip_buffer_push(&port->port); } - tty_kref_put(tty); /* Resubmit urb so we continue receiving */ err = usb_submit_urb(urb, GFP_ATOMIC); @@ -718,7 +675,6 @@ static void usa49wg_indat_callback(struct urb *urb) int i, len, x, err; struct usb_serial *serial; struct usb_serial_port *port; - struct tty_struct *tty; unsigned char *data = urb->transfer_buffer; int status = urb->status; @@ -733,46 +689,45 @@ static void usa49wg_indat_callback(struct urb *urb) i = 0; len = 0; - if (urb->actual_length) { - while (i < urb->actual_length) { + while (i < urb->actual_length) { - /* Check port number from message*/ - if (data[i] >= serial->num_ports) { - dev_dbg(&urb->dev->dev, "%s - Unexpected port number %d\n", - __func__, data[i]); - return; - } - port = serial->port[data[i++]]; - tty = tty_port_tty_get(&port->port); - len = data[i++]; + /* Check port number from message */ + if (data[i] >= serial->num_ports) { + dev_dbg(&urb->dev->dev, "%s - Unexpected port number %d\n", + __func__, data[i]); + return; + } + port = serial->port[data[i++]]; + len = data[i++]; - /* 0x80 bit is error flag */ - if ((data[i] & 0x80) == 0) { - /* no error on any byte */ - i++; - for (x = 1; x < len ; ++x) - tty_insert_flip_char(tty, data[i++], 0); - } else { - /* - * some bytes had errors, every byte has status - */ - for (x = 0; x + 1 < len; x += 2) { - int stat = data[i], flag = 0; - if (stat & RXERROR_OVERRUN) - flag |= TTY_OVERRUN; - if (stat & RXERROR_FRAMING) - flag |= TTY_FRAME; - if (stat & RXERROR_PARITY) - flag |= TTY_PARITY; - /* XXX should handle break (0x10) */ - tty_insert_flip_char(tty, - data[i+1], flag); - i += 2; - } + /* 0x80 bit is error flag */ + if ((data[i] & 0x80) == 0) { + /* no error on any byte */ + i++; + for (x = 1; x < len && i < urb->actual_length; ++x) + tty_insert_flip_char(&port->port, + data[i++], 0); + } else { + /* + * some bytes had errors, every byte has status + */ + for (x = 0; x + 1 < len && + i + 1 < urb->actual_length; x += 2) { + int stat = data[i], flag = 0; + + if (stat & RXERROR_OVERRUN) + flag |= TTY_OVERRUN; + if (stat & RXERROR_FRAMING) + flag |= TTY_FRAME; + if (stat & RXERROR_PARITY) + flag |= TTY_PARITY; + /* XXX should handle break (0x10) */ + tty_insert_flip_char(&port->port, data[i+1], + flag); + i += 2; } - tty_flip_buffer_push(tty); - tty_kref_put(tty); } + tty_flip_buffer_push(&port->port); } /* Resubmit urb so we continue receiving */ @@ -792,7 +747,6 @@ static void usa90_indat_callback(struct urb *urb) int endpoint; struct usb_serial_port *port; struct keyspan_port_private *p_priv; - struct tty_struct *tty; unsigned char *data = urb->transfer_buffer; int status = urb->status; @@ -808,12 +762,12 @@ static void usa90_indat_callback(struct urb *urb) p_priv = usb_get_serial_port_data(port); if (urb->actual_length) { - tty = tty_port_tty_get(&port->port); /* if current mode is DMA, looks like usa28 format otherwise looks like usa26 data format */ if (p_priv->baud > 57600) - tty_insert_flip_string(tty, data, urb->actual_length); + tty_insert_flip_string(&port->port, data, + urb->actual_length); else { /* 0x80 bit is error flag */ if ((data[0] & 0x80) == 0) { @@ -824,8 +778,8 @@ static void usa90_indat_callback(struct urb *urb) else err = 0; for (i = 1; i < urb->actual_length ; ++i) - tty_insert_flip_char(tty, data[i], - err); + tty_insert_flip_char(&port->port, + data[i], err); } else { /* some bytes had errors, every byte has status */ dev_dbg(&port->dev, "%s - RX error!!!!\n", __func__); @@ -838,13 +792,12 @@ static void usa90_indat_callback(struct urb *urb) if (stat & RXERROR_PARITY) flag |= TTY_PARITY; /* XXX should handle break (0x10) */ - tty_insert_flip_char(tty, data[i+1], - flag); + tty_insert_flip_char(&port->port, + data[i+1], flag); } } } - tty_flip_buffer_push(tty); - tty_kref_put(tty); + tty_flip_buffer_push(&port->port); } /* Resubmit urb so we continue receiving */ @@ -861,7 +814,6 @@ static void usa90_instat_callback(struct urb *urb) struct usb_serial *serial; struct usb_serial_port *port; struct keyspan_port_private *p_priv; - struct tty_struct *tty; int old_dcd_state, err; int status = urb->status; @@ -890,12 +842,8 @@ static void usa90_instat_callback(struct urb *urb) p_priv->dcd_state = ((msg->dcd) ? 1 : 0); p_priv->ri_state = ((msg->ri) ? 1 : 0); - if (old_dcd_state != p_priv->dcd_state && old_dcd_state) { - tty = tty_port_tty_get(&port->port); - if (tty && !C_CLOCAL(tty)) - tty_hangup(tty); - tty_kref_put(tty); - } + if (old_dcd_state != p_priv->dcd_state && old_dcd_state) + tty_port_tty_hangup(&port->port, true); /* Resubmit urb so we continue receiving */ err = usb_submit_urb(urb, GFP_ATOMIC); @@ -963,12 +911,8 @@ static void usa67_instat_callback(struct urb *urb) p_priv->cts_state = ((msg->hskia_cts) ? 1 : 0); p_priv->dcd_state = ((msg->gpia_dcd) ? 1 : 0); - if (old_dcd_state != p_priv->dcd_state && old_dcd_state) { - struct tty_struct *tty = tty_port_tty_get(&port->port); - if (tty && !C_CLOCAL(tty)) - tty_hangup(tty); - tty_kref_put(tty); - } + if (old_dcd_state != p_priv->dcd_state && old_dcd_state) + tty_port_tty_hangup(&port->port, true); /* Resubmit urb so we continue receiving */ err = usb_submit_urb(urb, GFP_ATOMIC); @@ -1083,7 +1027,7 @@ static int keyspan_open(struct tty_struct *tty, struct usb_serial_port *port) /* get the terminal config for the setup message now so we don't * need to send 2 of them */ - device_port = port->number - port->serial->minor; + device_port = port->port_number; if (tty) { cflag = tty->termios.c_cflag; /* Baud rate calculation takes baud rate as an integer @@ -1125,7 +1069,6 @@ static void keyspan_dtr_rts(struct usb_serial_port *port, int on) static void keyspan_close(struct usb_serial_port *port) { int i; - struct usb_serial *serial = port->serial; struct keyspan_port_private *p_priv; p_priv = usb_get_serial_port_data(port); @@ -1133,28 +1076,17 @@ static void keyspan_close(struct usb_serial_port *port) p_priv->rts_state = 0; p_priv->dtr_state = 0; - if (serial->dev) { - keyspan_send_setup(port, 2); - /* pilot-xfer seems to work best with this delay */ - mdelay(100); - /* keyspan_set_termios(port, NULL); */ - } - - /*while (p_priv->outcont_urb->status == -EINPROGRESS) { - dev_dbg(&port->dev, "%s - urb in progress\n", __func__); - }*/ + keyspan_send_setup(port, 2); + /* pilot-xfer seems to work best with this delay */ + mdelay(100); p_priv->out_flip = 0; p_priv->in_flip = 0; - if (serial->dev) { - /* Stop reading/writing urbs */ - stop_urb(p_priv->inack_urb); - /* stop_urb(p_priv->outcont_urb); */ - for (i = 0; i < 2; i++) { - stop_urb(p_priv->in_urbs[i]); - stop_urb(p_priv->out_urbs[i]); - } + stop_urb(p_priv->inack_urb); + for (i = 0; i < 2; i++) { + stop_urb(p_priv->in_urbs[i]); + stop_urb(p_priv->out_urbs[i]); } } @@ -1276,10 +1208,8 @@ static struct urb *keyspan_setup_urb(struct usb_serial *serial, int endpoint, dev_dbg(&serial->interface->dev, "%s - alloc for endpoint %d.\n", __func__, endpoint); urb = usb_alloc_urb(0, GFP_KERNEL); /* No ISO */ - if (urb == NULL) { - dev_dbg(&serial->interface->dev, "%s - alloc for endpoint %d failed.\n", __func__, endpoint); + if (!urb) return NULL; - } if (endpoint == 0) { /* control EP filled in when used */ @@ -1593,7 +1523,6 @@ static int keyspan_usa26_send_setup(struct usb_serial *serial, struct keyspan_serial_private *s_priv; struct keyspan_port_private *p_priv; const struct keyspan_device_details *d_details; - int outcont_urb; struct urb *this_urb; int device_port, err; @@ -1602,19 +1531,18 @@ static int keyspan_usa26_send_setup(struct usb_serial *serial, s_priv = usb_get_serial_data(serial); p_priv = usb_get_serial_port_data(port); d_details = s_priv->device_details; - device_port = port->number - port->serial->minor; + device_port = port->port_number; - outcont_urb = d_details->outcont_endpoints[port->number]; this_urb = p_priv->outcont_urb; - dev_dbg(&port->dev, "%s - endpoint %d\n", __func__, usb_pipeendpoint(this_urb->pipe)); - /* Make sure we have an urb then send the message */ if (this_urb == NULL) { dev_dbg(&port->dev, "%s - oops no urb.\n", __func__); return -1; } + dev_dbg(&port->dev, "%s - endpoint %d\n", __func__, usb_pipeendpoint(this_urb->pipe)); + /* Save reset port val for resend. Don't overwrite resend for open/close condition. */ if ((reset_port + 1) > p_priv->resend_cont) @@ -1730,14 +1658,6 @@ static int keyspan_usa26_send_setup(struct usb_serial *serial, err = usb_submit_urb(this_urb, GFP_ATOMIC); if (err != 0) dev_dbg(&port->dev, "%s - usb_submit_urb(setup) failed (%d)\n", __func__, err); -#if 0 - else { - dev_dbg(&port->dev, "%s - usb_submit_urb(%d) OK %d bytes (end %d)\n", __func__ - outcont_urb, this_urb->transfer_buffer_length, - usb_pipeendpoint(this_urb->pipe)); - } -#endif - return 0; } @@ -1755,7 +1675,7 @@ static int keyspan_usa28_send_setup(struct usb_serial *serial, s_priv = usb_get_serial_data(serial); p_priv = usb_get_serial_port_data(port); d_details = s_priv->device_details; - device_port = port->number - port->serial->minor; + device_port = port->port_number; /* only do something if we have a bulk out endpoint */ this_urb = p_priv->outcont_urb; @@ -1856,12 +1776,6 @@ static int keyspan_usa28_send_setup(struct usb_serial *serial, err = usb_submit_urb(this_urb, GFP_ATOMIC); if (err != 0) dev_dbg(&port->dev, "%s - usb_submit_urb(setup) failed\n", __func__); -#if 0 - else { - dev_dbg(&port->dev, "%s - usb_submit_urb(setup) OK %d bytes\n", __func__, - this_urb->transfer_buffer_length); - } -#endif return 0; } @@ -1885,17 +1799,16 @@ static int keyspan_usa49_send_setup(struct usb_serial *serial, this_urb = s_priv->glocont_urb; /* Work out which port within the device is being setup */ - device_port = port->number - port->serial->minor; + device_port = port->port_number; /* Make sure we have an urb then send the message */ if (this_urb == NULL) { - dev_dbg(&port->dev, "%s - oops no urb for port %d.\n", __func__, port->number); + dev_dbg(&port->dev, "%s - oops no urb for port.\n", __func__); return -1; } - dev_dbg(&port->dev, "%s - endpoint %d port %d (%d)\n", - __func__, usb_pipeendpoint(this_urb->pipe), - port->number, device_port); + dev_dbg(&port->dev, "%s - endpoint %d (%d)\n", + __func__, usb_pipeendpoint(this_urb->pipe), device_port); /* Save reset port val for resend. Don't overwrite resend for open/close condition. */ @@ -1910,7 +1823,6 @@ static int keyspan_usa49_send_setup(struct usb_serial *serial, memset(&msg, 0, sizeof(struct keyspan_usa49_portControlMessage)); - /*msg.portNumber = port->number;*/ msg.portNumber = device_port; /* Only set baud rate if it's changed */ @@ -2041,13 +1953,6 @@ static int keyspan_usa49_send_setup(struct usb_serial *serial, err = usb_submit_urb(this_urb, GFP_ATOMIC); if (err != 0) dev_dbg(&port->dev, "%s - usb_submit_urb(setup) failed (%d)\n", __func__, err); -#if 0 - else { - dev_dbg(&port->dev, "%s - usb_submit_urb(%d) OK %d bytes (end %d)\n", __func__, - outcont_urb, this_urb->transfer_buffer_length, - usb_pipeendpoint(this_urb->pipe)); - } -#endif return 0; } @@ -2200,12 +2105,11 @@ static int keyspan_usa67_send_setup(struct usb_serial *serial, this_urb = s_priv->glocont_urb; /* Work out which port within the device is being setup */ - device_port = port->number - port->serial->minor; + device_port = port->port_number; /* Make sure we have an urb then send the message */ if (this_urb == NULL) { - dev_dbg(&port->dev, "%s - oops no urb for port %d.\n", __func__, - port->number); + dev_dbg(&port->dev, "%s - oops no urb for port.\n", __func__); return -1; } @@ -2370,15 +2274,29 @@ static int keyspan_startup(struct usb_serial *serial) if (d_details == NULL) { dev_err(&serial->dev->dev, "%s - unknown product id %x\n", __func__, le16_to_cpu(serial->dev->descriptor.idProduct)); - return 1; + return -ENODEV; } /* Setup private data for serial driver */ s_priv = kzalloc(sizeof(struct keyspan_serial_private), GFP_KERNEL); - if (!s_priv) { - dev_dbg(&serial->dev->dev, "%s - kmalloc for keyspan_serial_private failed.\n", __func__); + if (!s_priv) return -ENOMEM; - } + + s_priv->instat_buf = kzalloc(INSTAT_BUFLEN, GFP_KERNEL); + if (!s_priv->instat_buf) + goto err_instat_buf; + + s_priv->indat_buf = kzalloc(INDAT49W_BUFLEN, GFP_KERNEL); + if (!s_priv->indat_buf) + goto err_indat_buf; + + s_priv->glocont_buf = kzalloc(GLOCONT_BUFLEN, GFP_KERNEL); + if (!s_priv->glocont_buf) + goto err_glocont_buf; + + s_priv->ctrl_buf = kzalloc(sizeof(struct usb_ctrlrequest), GFP_KERNEL); + if (!s_priv->ctrl_buf) + goto err_ctrl_buf; s_priv->device_details = d_details; usb_set_serial_data(serial, s_priv); @@ -2397,6 +2315,17 @@ static int keyspan_startup(struct usb_serial *serial) } return 0; + +err_ctrl_buf: + kfree(s_priv->glocont_buf); +err_glocont_buf: + kfree(s_priv->indat_buf); +err_indat_buf: + kfree(s_priv->instat_buf); +err_instat_buf: + kfree(s_priv); + + return -ENOMEM; } static void keyspan_disconnect(struct usb_serial *serial) @@ -2420,6 +2349,11 @@ static void keyspan_release(struct usb_serial *serial) usb_free_urb(s_priv->indat_urb); usb_free_urb(s_priv->glocont_urb); + kfree(s_priv->ctrl_buf); + kfree(s_priv->glocont_buf); + kfree(s_priv->indat_buf); + kfree(s_priv->instat_buf); + kfree(s_priv); } @@ -2441,19 +2375,40 @@ static int keyspan_port_probe(struct usb_serial_port *port) if (!p_priv) return -ENOMEM; + for (i = 0; i < ARRAY_SIZE(p_priv->in_buffer); ++i) { + p_priv->in_buffer[i] = kzalloc(IN_BUFLEN, GFP_KERNEL); + if (!p_priv->in_buffer[i]) + goto err_in_buffer; + } + + for (i = 0; i < ARRAY_SIZE(p_priv->out_buffer); ++i) { + p_priv->out_buffer[i] = kzalloc(OUT_BUFLEN, GFP_KERNEL); + if (!p_priv->out_buffer[i]) + goto err_out_buffer; + } + + p_priv->inack_buffer = kzalloc(INACK_BUFLEN, GFP_KERNEL); + if (!p_priv->inack_buffer) + goto err_inack_buffer; + + p_priv->outcont_buffer = kzalloc(OUTCONT_BUFLEN, GFP_KERNEL); + if (!p_priv->outcont_buffer) + goto err_outcont_buffer; + p_priv->device_details = d_details; /* Setup values for the various callback routines */ cback = &keyspan_callbacks[d_details->msg_format]; - port_num = port->number - port->serial->minor; + port_num = port->port_number; /* Do indat endpoints first, once for each flip */ endp = d_details->indat_endpoints[port_num]; for (i = 0; i <= d_details->indat_endp_flip; ++i, ++endp) { p_priv->in_urbs[i] = keyspan_setup_urb(serial, endp, USB_DIR_IN, port, - p_priv->in_buffer[i], 64, + p_priv->in_buffer[i], + IN_BUFLEN, cback->indat_callback); } /* outdat endpoints also have flip */ @@ -2461,25 +2416,41 @@ static int keyspan_port_probe(struct usb_serial_port *port) for (i = 0; i <= d_details->outdat_endp_flip; ++i, ++endp) { p_priv->out_urbs[i] = keyspan_setup_urb(serial, endp, USB_DIR_OUT, port, - p_priv->out_buffer[i], 64, + p_priv->out_buffer[i], + OUT_BUFLEN, cback->outdat_callback); } /* inack endpoint */ p_priv->inack_urb = keyspan_setup_urb(serial, d_details->inack_endpoints[port_num], USB_DIR_IN, port, - p_priv->inack_buffer, 1, + p_priv->inack_buffer, + INACK_BUFLEN, cback->inack_callback); /* outcont endpoint */ p_priv->outcont_urb = keyspan_setup_urb(serial, d_details->outcont_endpoints[port_num], USB_DIR_OUT, port, - p_priv->outcont_buffer, 64, + p_priv->outcont_buffer, + OUTCONT_BUFLEN, cback->outcont_callback); usb_set_serial_port_data(port, p_priv); return 0; + +err_outcont_buffer: + kfree(p_priv->inack_buffer); +err_inack_buffer: + for (i = 0; i < ARRAY_SIZE(p_priv->out_buffer); ++i) + kfree(p_priv->out_buffer[i]); +err_out_buffer: + for (i = 0; i < ARRAY_SIZE(p_priv->in_buffer); ++i) + kfree(p_priv->in_buffer[i]); +err_in_buffer: + kfree(p_priv); + + return -ENOMEM; } static int keyspan_port_remove(struct usb_serial_port *port) @@ -2503,6 +2474,13 @@ static int keyspan_port_remove(struct usb_serial_port *port) usb_free_urb(p_priv->out_urbs[i]); } + kfree(p_priv->outcont_buffer); + kfree(p_priv->inack_buffer); + for (i = 0; i < ARRAY_SIZE(p_priv->out_buffer); ++i) + kfree(p_priv->out_buffer[i]); + for (i = 0; i < ARRAY_SIZE(p_priv->in_buffer); ++i) + kfree(p_priv->in_buffer[i]); + kfree(p_priv); return 0; diff --git a/drivers/usb/serial/keyspan_pda.c b/drivers/usb/serial/keyspan_pda.c index 41b01092af0..742d827f876 100644 --- a/drivers/usb/serial/keyspan_pda.c +++ b/drivers/usb/serial/keyspan_pda.c @@ -17,7 +17,6 @@ #include <linux/kernel.h> #include <linux/errno.h> -#include <linux/init.h> #include <linux/slab.h> #include <linux/tty.h> #include <linux/tty_driver.h> @@ -104,10 +103,8 @@ static void keyspan_pda_wakeup_write(struct work_struct *work) struct keyspan_pda_private *priv = container_of(work, struct keyspan_pda_private, wakeup_work); struct usb_serial_port *port = priv->port; - struct tty_struct *tty = tty_port_tty_get(&port->port); - if (tty) - tty_wakeup(tty); - tty_kref_put(tty); + + tty_port_tty_wakeup(&port->port); } static void keyspan_pda_request_unthrottle(struct work_struct *work) @@ -138,7 +135,6 @@ static void keyspan_pda_request_unthrottle(struct work_struct *work) static void keyspan_pda_rx_interrupt(struct urb *urb) { struct usb_serial_port *port = urb->context; - struct tty_struct *tty; unsigned char *data = urb->transfer_buffer; int retval; int status = urb->status; @@ -163,14 +159,12 @@ static void keyspan_pda_rx_interrupt(struct urb *urb) /* see if the message is data or a status interrupt */ switch (data[0]) { case 0: - tty = tty_port_tty_get(&port->port); /* rest of message is rx data */ - if (tty && urb->actual_length) { - tty_insert_flip_string(tty, data + 1, + if (urb->actual_length) { + tty_insert_flip_string(&port->port, data + 1, urb->actual_length - 1); - tty_flip_buffer_push(tty); + tty_flip_buffer_push(&port->port); } - tty_kref_put(tty); break; case 1: /* status interrupt */ @@ -195,7 +189,7 @@ exit: retval = usb_submit_urb(urb, GFP_ATOMIC); if (retval) dev_err(&port->dev, - "%s - usb_submit_urb failed with result %d", + "%s - usb_submit_urb failed with result %d\n", __func__, retval); } @@ -598,12 +592,10 @@ static void keyspan_pda_dtr_rts(struct usb_serial_port *port, int on) { struct usb_serial *serial = port->serial; - if (serial->dev) { - if (on) - keyspan_pda_set_modem_info(serial, (1<<7) | (1<< 2)); - else - keyspan_pda_set_modem_info(serial, 0); - } + if (on) + keyspan_pda_set_modem_info(serial, (1 << 7) | (1 << 2)); + else + keyspan_pda_set_modem_info(serial, 0); } @@ -654,13 +646,8 @@ error: } static void keyspan_pda_close(struct usb_serial_port *port) { - struct usb_serial *serial = port->serial; - - if (serial->dev) { - /* shutdown our bulk reads and writes */ - usb_kill_urb(port->write_urb); - usb_kill_urb(port->interrupt_in_urb); - } + usb_kill_urb(port->write_urb); + usb_kill_urb(port->interrupt_in_urb); } diff --git a/drivers/usb/serial/keyspan_usa26msg.h b/drivers/usb/serial/keyspan_usa26msg.h index 3808727db65..09e21e84fc4 100644 --- a/drivers/usb/serial/keyspan_usa26msg.h +++ b/drivers/usb/serial/keyspan_usa26msg.h @@ -62,7 +62,7 @@ or: (b) 0x80 bit set - indiates that the bytes following alternate data and + indicates that the bytes following alternate data and status bytes: STAT DATA STAT DATA STAT DATA STAT DATA ... diff --git a/drivers/usb/serial/kl5kusb105.c b/drivers/usb/serial/kl5kusb105.c index fc9e14a1e9b..d7440b7557a 100644 --- a/drivers/usb/serial/kl5kusb105.c +++ b/drivers/usb/serial/kl5kusb105.c @@ -37,7 +37,6 @@ #include <linux/kernel.h> #include <linux/errno.h> -#include <linux/init.h> #include <linux/slab.h> #include <linux/tty.h> #include <linux/tty_driver.h> @@ -182,11 +181,9 @@ static int klsi_105_get_line_state(struct usb_serial_port *port, dev_info(&port->serial->dev->dev, "sending SIO Poll request\n"); status_buf = kmalloc(KLSI_STATUSBUF_LEN, GFP_KERNEL); - if (!status_buf) { - dev_err(&port->dev, "%s - out of memory for status buffer.\n", - __func__); + if (!status_buf) return -ENOMEM; - } + status_buf[0] = 0xff; status_buf[1] = 0xff; rc = usb_control_msg(port->serial->dev, @@ -204,7 +201,7 @@ static int klsi_105_get_line_state(struct usb_serial_port *port, else { status = get_unaligned_le16(status_buf); - dev_info(&port->serial->dev->dev, "read status %x %x", + dev_info(&port->serial->dev->dev, "read status %x %x\n", status_buf[0], status_buf[1]); *line_state_p = klsi_105_status2linestate(status); @@ -273,11 +270,9 @@ static int klsi_105_open(struct tty_struct *tty, struct usb_serial_port *port) * priv->line_state. */ cfg = kmalloc(sizeof(*cfg), GFP_KERNEL); - if (!cfg) { - dev_err(&port->dev, "%s - out of memory for config buffer.\n", - __func__); + if (!cfg) return -ENOMEM; - } + cfg->pktlen = 5; cfg->baudrate = kl5kusb105a_sio_b9600; cfg->databits = kl5kusb105a_dtb_8; @@ -341,28 +336,20 @@ static void klsi_105_close(struct usb_serial_port *port) { int rc; - mutex_lock(&port->serial->disc_mutex); - if (!port->serial->disconnected) { - /* send READ_OFF */ - rc = usb_control_msg(port->serial->dev, - usb_sndctrlpipe(port->serial->dev, 0), - KL5KUSB105A_SIO_CONFIGURE, - USB_TYPE_VENDOR | USB_DIR_OUT, - KL5KUSB105A_SIO_CONFIGURE_READ_OFF, - 0, /* index */ - NULL, 0, - KLSI_TIMEOUT); - if (rc < 0) - dev_err(&port->dev, - "Disabling read failed (error = %d)\n", rc); - } - mutex_unlock(&port->serial->disc_mutex); + /* send READ_OFF */ + rc = usb_control_msg(port->serial->dev, + usb_sndctrlpipe(port->serial->dev, 0), + KL5KUSB105A_SIO_CONFIGURE, + USB_TYPE_VENDOR | USB_DIR_OUT, + KL5KUSB105A_SIO_CONFIGURE_READ_OFF, + 0, /* index */ + NULL, 0, + KLSI_TIMEOUT); + if (rc < 0) + dev_err(&port->dev, "failed to disable read: %d\n", rc); /* shutdown our bulk reads and writes */ usb_serial_generic_close(port); - - /* wgg - do I need this? I think so. */ - usb_kill_urb(port->interrupt_in_urb); } /* We need to write a complete 64-byte data block and encode the @@ -389,7 +376,6 @@ static void klsi_105_process_read_urb(struct urb *urb) { struct usb_serial_port *port = urb->context; unsigned char *data = urb->transfer_buffer; - struct tty_struct *tty; unsigned len; /* empty urbs seem to happen, we ignore them */ @@ -401,19 +387,14 @@ static void klsi_105_process_read_urb(struct urb *urb) return; } - tty = tty_port_tty_get(&port->port); - if (!tty) - return; - len = get_unaligned_le16(data); if (len > urb->actual_length - KLSI_HDR_LEN) { dev_dbg(&port->dev, "%s - packet length mismatch\n", __func__); len = urb->actual_length - KLSI_HDR_LEN; } - tty_insert_flip_string(tty, data + KLSI_HDR_LEN, len); - tty_flip_buffer_push(tty); - tty_kref_put(tty); + tty_insert_flip_string(&port->port, data + KLSI_HDR_LEN, len); + tty_flip_buffer_push(&port->port); } static void klsi_105_set_termios(struct tty_struct *tty, @@ -431,10 +412,8 @@ static void klsi_105_set_termios(struct tty_struct *tty, speed_t baud; cfg = kmalloc(sizeof(*cfg), GFP_KERNEL); - if (!cfg) { - dev_err(dev, "%s - out of memory for config buffer.\n", __func__); + if (!cfg) return; - } /* lock while we are modifying the settings */ spin_lock_irqsave(&priv->lock, flags); @@ -485,7 +464,7 @@ static void klsi_105_set_termios(struct tty_struct *tty, priv->cfg.baudrate = kl5kusb105a_sio_b115200; break; default: - dev_dbg(dev, "KLSI USB->Serial converter: unsupported baudrate request, using default of 9600"); + dev_dbg(dev, "unsupported baudrate, using 9600\n"); priv->cfg.baudrate = kl5kusb105a_sio_b9600; baud = 9600; break; diff --git a/drivers/usb/serial/kobil_sct.c b/drivers/usb/serial/kobil_sct.c index b747ba615d0..078f9ed419c 100644 --- a/drivers/usb/serial/kobil_sct.c +++ b/drivers/usb/serial/kobil_sct.c @@ -25,7 +25,6 @@ #include <linux/kernel.h> #include <linux/errno.h> -#include <linux/init.h> #include <linux/slab.h> #include <linux/tty.h> #include <linux/tty_driver.h> @@ -65,7 +64,7 @@ static int kobil_tiocmget(struct tty_struct *tty); static int kobil_tiocmset(struct tty_struct *tty, unsigned int set, unsigned int clear); static void kobil_read_int_callback(struct urb *urb); -static void kobil_write_callback(struct urb *purb); +static void kobil_write_int_callback(struct urb *urb); static void kobil_set_termios(struct tty_struct *tty, struct usb_serial_port *port, struct ktermios *old); static void kobil_init_termios(struct tty_struct *tty); @@ -99,6 +98,7 @@ static struct usb_serial_driver kobil_device = { .write = kobil_write, .write_room = kobil_write_room, .read_int_callback = kobil_read_int_callback, + .write_int_callback = kobil_write_int_callback, }; static struct usb_serial_driver * const serial_drivers[] = { @@ -106,8 +106,6 @@ static struct usb_serial_driver * const serial_drivers[] = { }; struct kobil_private { - int write_int_endpoint_address; - int read_int_endpoint_address; unsigned char buf[KOBIL_BUF_LENGTH]; /* buffer for the APDU to send */ int filled; /* index of the last char in buf */ int cur_pos; /* index of the next char to send in buf */ @@ -117,14 +115,8 @@ struct kobil_private { static int kobil_port_probe(struct usb_serial_port *port) { - int i; struct usb_serial *serial = port->serial; struct kobil_private *priv; - struct usb_device *pdev; - struct usb_host_config *actconfig; - struct usb_interface *interface; - struct usb_host_interface *altsetting; - struct usb_host_endpoint *endpoint; priv = kmalloc(sizeof(struct kobil_private), GFP_KERNEL); if (!priv) @@ -150,30 +142,6 @@ static int kobil_port_probe(struct usb_serial_port *port) } usb_set_serial_port_data(port, priv); - /* search for the necessary endpoints */ - pdev = serial->dev; - actconfig = pdev->actconfig; - interface = actconfig->interface[0]; - altsetting = interface->cur_altsetting; - endpoint = altsetting->endpoint; - - for (i = 0; i < altsetting->desc.bNumEndpoints; i++) { - endpoint = &altsetting->endpoint[i]; - if (usb_endpoint_is_int_out(&endpoint->desc)) { - dev_dbg(&serial->dev->dev, - "%s Found interrupt out endpoint. Address: %d\n", - __func__, endpoint->desc.bEndpointAddress); - priv->write_int_endpoint_address = - endpoint->desc.bEndpointAddress; - } - if (usb_endpoint_is_int_in(&endpoint->desc)) { - dev_dbg(&serial->dev->dev, - "%s Found interrupt in endpoint. Address: %d\n", - __func__, endpoint->desc.bEndpointAddress); - priv->read_int_endpoint_address = - endpoint->desc.bEndpointAddress; - } - } return 0; } @@ -205,7 +173,6 @@ static int kobil_open(struct tty_struct *tty, struct usb_serial_port *port) struct kobil_private *priv; unsigned char *transfer_buffer; int transfer_buffer_length = 8; - int write_urb_transfer_buffer_length = 8; priv = usb_get_serial_port_data(port); @@ -214,27 +181,6 @@ static int kobil_open(struct tty_struct *tty, struct usb_serial_port *port) if (!transfer_buffer) return -ENOMEM; - /* allocate write_urb */ - if (!port->write_urb) { - dev_dbg(dev, "%s - Allocating port->write_urb\n", __func__); - port->write_urb = usb_alloc_urb(0, GFP_KERNEL); - if (!port->write_urb) { - dev_dbg(dev, "%s - usb_alloc_urb failed\n", __func__); - kfree(transfer_buffer); - return -ENOMEM; - } - } - - /* allocate memory for write_urb transfer buffer */ - port->write_urb->transfer_buffer = - kmalloc(write_urb_transfer_buffer_length, GFP_KERNEL); - if (!port->write_urb->transfer_buffer) { - kfree(transfer_buffer); - usb_free_urb(port->write_urb); - port->write_urb = NULL; - return -ENOMEM; - } - /* get hardware version */ result = usb_control_msg(port->serial->dev, usb_rcvctrlpipe(port->serial->dev, 0), @@ -247,7 +193,7 @@ static int kobil_open(struct tty_struct *tty, struct usb_serial_port *port) KOBIL_TIMEOUT ); dev_dbg(dev, "%s - Send get_HW_version URB returns: %i\n", __func__, result); - dev_dbg(dev, "Harware version: %i.%i.%i\n", transfer_buffer[0], + dev_dbg(dev, "Hardware version: %i.%i.%i\n", transfer_buffer[0], transfer_buffer[1], transfer_buffer[2]); /* get firmware version */ @@ -269,13 +215,13 @@ static int kobil_open(struct tty_struct *tty, struct usb_serial_port *port) priv->device_type == KOBIL_ADAPTER_K_PRODUCT_ID) { /* Setting Baudrate, Parity and Stopbits */ result = usb_control_msg(port->serial->dev, - usb_rcvctrlpipe(port->serial->dev, 0), + usb_sndctrlpipe(port->serial->dev, 0), SUSBCRequest_SetBaudRateParityAndStopBits, USB_TYPE_VENDOR | USB_RECIP_ENDPOINT | USB_DIR_OUT, SUSBCR_SBR_9600 | SUSBCR_SPASB_EvenParity | SUSBCR_SPASB_1StopBit, 0, - transfer_buffer, + NULL, 0, KOBIL_TIMEOUT ); @@ -283,12 +229,12 @@ static int kobil_open(struct tty_struct *tty, struct usb_serial_port *port) /* reset all queues */ result = usb_control_msg(port->serial->dev, - usb_rcvctrlpipe(port->serial->dev, 0), + usb_sndctrlpipe(port->serial->dev, 0), SUSBCRequest_Misc, USB_TYPE_VENDOR | USB_RECIP_ENDPOINT | USB_DIR_OUT, SUSBCR_MSC_ResetAllQueues, 0, - transfer_buffer, + NULL, 0, KOBIL_TIMEOUT ); @@ -310,12 +256,7 @@ static int kobil_open(struct tty_struct *tty, struct usb_serial_port *port) static void kobil_close(struct usb_serial_port *port) { /* FIXME: Add rts/dtr methods */ - if (port->write_urb) { - usb_poison_urb(port->write_urb); - kfree(port->write_urb->transfer_buffer); - usb_free_urb(port->write_urb); - port->write_urb = NULL; - } + usb_kill_urb(port->interrupt_out_urb); usb_kill_urb(port->interrupt_in_urb); } @@ -324,7 +265,6 @@ static void kobil_read_int_callback(struct urb *urb) { int result; struct usb_serial_port *port = urb->context; - struct tty_struct *tty; unsigned char *data = urb->transfer_buffer; int status = urb->status; @@ -333,37 +273,19 @@ static void kobil_read_int_callback(struct urb *urb) return; } - tty = tty_port_tty_get(&port->port); - if (tty && urb->actual_length) { - - /* BEGIN DEBUG */ - /* - char *dbg_data; - - dbg_data = kzalloc((3 * purb->actual_length + 10) - * sizeof(char), GFP_KERNEL); - if (! dbg_data) { - return; - } - for (i = 0; i < purb->actual_length; i++) { - sprintf(dbg_data +3*i, "%02X ", data[i]); - } - dev_dbg(&port->dev, " <-- %s\n", dbg_data); - kfree(dbg_data); - */ - /* END DEBUG */ - - tty_insert_flip_string(tty, data, urb->actual_length); - tty_flip_buffer_push(tty); + if (urb->actual_length) { + usb_serial_debug_data(&port->dev, __func__, urb->actual_length, + data); + tty_insert_flip_string(&port->port, data, urb->actual_length); + tty_flip_buffer_push(&port->port); } - tty_kref_put(tty); result = usb_submit_urb(port->interrupt_in_urb, GFP_ATOMIC); dev_dbg(&port->dev, "%s - Send read URB returns: %i\n", __func__, result); } -static void kobil_write_callback(struct urb *purb) +static void kobil_write_int_callback(struct urb *urb) { } @@ -406,23 +328,14 @@ static int kobil_write(struct tty_struct *tty, struct usb_serial_port *port, while (todo > 0) { /* max 8 byte in one urb (endpoint size) */ - length = (todo < 8) ? todo : 8; + length = min(todo, port->interrupt_out_size); /* copy data to transfer buffer */ - memcpy(port->write_urb->transfer_buffer, + memcpy(port->interrupt_out_buffer, priv->buf + priv->cur_pos, length); - usb_fill_int_urb(port->write_urb, - port->serial->dev, - usb_sndintpipe(port->serial->dev, - priv->write_int_endpoint_address), - port->write_urb->transfer_buffer, - length, - kobil_write_callback, - port, - 8 - ); + port->interrupt_out_urb->transfer_buffer_length = length; priv->cur_pos = priv->cur_pos + length; - result = usb_submit_urb(port->write_urb, GFP_NOIO); + result = usb_submit_urb(port->interrupt_out_urb, GFP_NOIO); dev_dbg(&port->dev, "%s - Send write URB returns: %i\n", __func__, result); todo = priv->filled - priv->cur_pos; @@ -532,12 +445,12 @@ static int kobil_tiocmset(struct tty_struct *tty, else dev_dbg(dev, "%s - Clearing DTR\n", __func__); result = usb_control_msg(port->serial->dev, - usb_rcvctrlpipe(port->serial->dev, 0), + usb_sndctrlpipe(port->serial->dev, 0), SUSBCRequest_SetStatusLinesOrQueues, USB_TYPE_VENDOR | USB_RECIP_ENDPOINT | USB_DIR_OUT, ((dtr != 0) ? SUSBCR_SSL_SETDTR : SUSBCR_SSL_CLRDTR), 0, - transfer_buffer, + NULL, 0, KOBIL_TIMEOUT); } else { @@ -546,12 +459,12 @@ static int kobil_tiocmset(struct tty_struct *tty, else dev_dbg(dev, "%s - Clearing RTS\n", __func__); result = usb_control_msg(port->serial->dev, - usb_rcvctrlpipe(port->serial->dev, 0), + usb_sndctrlpipe(port->serial->dev, 0), SUSBCRequest_SetStatusLinesOrQueues, USB_TYPE_VENDOR | USB_RECIP_ENDPOINT | USB_DIR_OUT, ((rts != 0) ? SUSBCR_SSL_SETRTS : SUSBCR_SSL_CLRRTS), 0, - transfer_buffer, + NULL, 0, KOBIL_TIMEOUT); } @@ -601,7 +514,7 @@ static void kobil_set_termios(struct tty_struct *tty, tty_encode_baud_rate(tty, speed, speed); result = usb_control_msg(port->serial->dev, - usb_rcvctrlpipe(port->serial->dev, 0), + usb_sndctrlpipe(port->serial->dev, 0), SUSBCRequest_SetBaudRateParityAndStopBits, USB_TYPE_VENDOR | USB_RECIP_ENDPOINT | USB_DIR_OUT, urb_val, @@ -633,18 +546,19 @@ static int kobil_ioctl(struct tty_struct *tty, return -ENOBUFS; result = usb_control_msg(port->serial->dev, - usb_rcvctrlpipe(port->serial->dev, 0), + usb_sndctrlpipe(port->serial->dev, 0), SUSBCRequest_Misc, USB_TYPE_VENDOR | USB_RECIP_ENDPOINT | USB_DIR_OUT, SUSBCR_MSC_ResetAllQueues, 0, - NULL, /* transfer_buffer, */ + NULL, 0, KOBIL_TIMEOUT ); dev_dbg(&port->dev, - "%s - Send reset_all_queues (FLUSH) URB returns: %i", __func__, result); + "%s - Send reset_all_queues (FLUSH) URB returns: %i\n", + __func__, result); kfree(transfer_buffer); return (result < 0) ? -EIO: 0; default: diff --git a/drivers/usb/serial/mct_u232.c b/drivers/usb/serial/mct_u232.c index b6911757c85..fd707d6a10e 100644 --- a/drivers/usb/serial/mct_u232.c +++ b/drivers/usb/serial/mct_u232.c @@ -23,7 +23,6 @@ #include <linux/kernel.h> #include <linux/errno.h> -#include <linux/init.h> #include <linux/slab.h> #include <linux/tty.h> #include <linux/tty_driver.h> @@ -35,7 +34,6 @@ #include <linux/usb.h> #include <linux/usb/serial.h> #include <linux/serial.h> -#include <linux/ioctl.h> #include "mct_u232.h" #define DRIVER_AUTHOR "Wolfgang Grandegger <wolfgang@ces.ch>" @@ -44,7 +42,6 @@ /* * Function prototypes */ -static int mct_u232_startup(struct usb_serial *serial); static int mct_u232_port_probe(struct usb_serial_port *port); static int mct_u232_port_remove(struct usb_serial_port *remove); static int mct_u232_open(struct tty_struct *tty, struct usb_serial_port *port); @@ -57,10 +54,6 @@ static void mct_u232_break_ctl(struct tty_struct *tty, int break_state); static int mct_u232_tiocmget(struct tty_struct *tty); static int mct_u232_tiocmset(struct tty_struct *tty, unsigned int set, unsigned int clear); -static int mct_u232_ioctl(struct tty_struct *tty, - unsigned int cmd, unsigned long arg); -static int mct_u232_get_icount(struct tty_struct *tty, - struct serial_icounter_struct *icount); static void mct_u232_throttle(struct tty_struct *tty); static void mct_u232_unthrottle(struct tty_struct *tty); @@ -95,11 +88,10 @@ static struct usb_serial_driver mct_u232_device = { .break_ctl = mct_u232_break_ctl, .tiocmget = mct_u232_tiocmget, .tiocmset = mct_u232_tiocmset, - .attach = mct_u232_startup, + .tiocmiwait = usb_serial_generic_tiocmiwait, .port_probe = mct_u232_port_probe, .port_remove = mct_u232_port_remove, - .ioctl = mct_u232_ioctl, - .get_icount = mct_u232_get_icount, + .get_icount = usb_serial_generic_get_icount, }; static struct usb_serial_driver * const serial_drivers[] = { @@ -107,15 +99,13 @@ static struct usb_serial_driver * const serial_drivers[] = { }; struct mct_u232_private { + struct urb *read_urb; spinlock_t lock; unsigned int control_state; /* Modem Line Setting (TIOCM) */ unsigned char last_lcr; /* Line Control Register */ unsigned char last_lsr; /* Line Status Register */ unsigned char last_msr; /* Modem Status Register */ unsigned int rx_flags; /* Throttling flags */ - struct async_icount icount; - wait_queue_head_t msr_wait; /* for handling sleeping while waiting - for msr change to happen */ }; #define THROTTLED 0x01 @@ -384,22 +374,6 @@ static void mct_u232_msr_to_state(struct usb_serial_port *port, * Driver's tty interface functions */ -static int mct_u232_startup(struct usb_serial *serial) -{ - struct usb_serial_port *port, *rport; - - /* Puh, that's dirty */ - port = serial->port[0]; - rport = serial->port[1]; - /* No unlinking, it wasn't submitted yet. */ - usb_free_urb(port->read_urb); - port->read_urb = rport->interrupt_in_urb; - rport->interrupt_in_urb = NULL; - port->read_urb->context = port; - - return 0; -} /* mct_u232_startup */ - static int mct_u232_port_probe(struct usb_serial_port *port) { struct mct_u232_private *priv; @@ -408,8 +382,11 @@ static int mct_u232_port_probe(struct usb_serial_port *port) if (!priv) return -ENOMEM; + /* Use second interrupt-in endpoint for reading. */ + priv->read_urb = port->serial->port[1]->interrupt_in_urb; + priv->read_urb->context = port; + spin_lock_init(&priv->lock); - init_waitqueue_head(&priv->msr_wait); usb_set_serial_port_data(port, priv); @@ -472,17 +449,17 @@ static int mct_u232_open(struct tty_struct *tty, struct usb_serial_port *port) mct_u232_msr_to_state(port, &priv->control_state, priv->last_msr); spin_unlock_irqrestore(&priv->lock, flags); - retval = usb_submit_urb(port->read_urb, GFP_KERNEL); + retval = usb_submit_urb(priv->read_urb, GFP_KERNEL); if (retval) { dev_err(&port->dev, - "usb_submit_urb(read bulk) failed pipe 0x%x err %d\n", + "usb_submit_urb(read) failed pipe 0x%x err %d\n", port->read_urb->pipe, retval); goto error; } retval = usb_submit_urb(port->interrupt_in_urb, GFP_KERNEL); if (retval) { - usb_kill_urb(port->read_urb); + usb_kill_urb(priv->read_urb); dev_err(&port->dev, "usb_submit_urb(read int) failed pipe 0x%x err %d", port->interrupt_in_urb->pipe, retval); @@ -499,28 +476,22 @@ static void mct_u232_dtr_rts(struct usb_serial_port *port, int on) unsigned int control_state; struct mct_u232_private *priv = usb_get_serial_port_data(port); - mutex_lock(&port->serial->disc_mutex); - if (!port->serial->disconnected) { - /* drop DTR and RTS */ - spin_lock_irq(&priv->lock); - if (on) - priv->control_state |= TIOCM_DTR | TIOCM_RTS; - else - priv->control_state &= ~(TIOCM_DTR | TIOCM_RTS); - control_state = priv->control_state; - spin_unlock_irq(&priv->lock); - mct_u232_set_modem_ctrl(port, control_state); - } - mutex_unlock(&port->serial->disc_mutex); + spin_lock_irq(&priv->lock); + if (on) + priv->control_state |= TIOCM_DTR | TIOCM_RTS; + else + priv->control_state &= ~(TIOCM_DTR | TIOCM_RTS); + control_state = priv->control_state; + spin_unlock_irq(&priv->lock); + + mct_u232_set_modem_ctrl(port, control_state); } static void mct_u232_close(struct usb_serial_port *port) { - /* - * Must kill the read urb as it is actually an interrupt urb, which - * generic close thus fails to kill. - */ - usb_kill_urb(port->read_urb); + struct mct_u232_private *priv = usb_get_serial_port_data(port); + + usb_kill_urb(priv->read_urb); usb_kill_urb(port->interrupt_in_urb); usb_serial_generic_close(port); @@ -531,7 +502,6 @@ static void mct_u232_read_int_callback(struct urb *urb) { struct usb_serial_port *port = urb->context; struct mct_u232_private *priv = usb_get_serial_port_data(port); - struct tty_struct *tty; unsigned char *data = urb->transfer_buffer; int retval; int status = urb->status; @@ -561,13 +531,9 @@ static void mct_u232_read_int_callback(struct urb *urb) */ if (urb->transfer_buffer_length > 2) { if (urb->actual_length) { - tty = tty_port_tty_get(&port->port); - if (tty) { - tty_insert_flip_string(tty, data, - urb->actual_length); - tty_flip_buffer_push(tty); - } - tty_kref_put(tty); + tty_insert_flip_string(&port->port, data, + urb->actual_length); + tty_flip_buffer_push(&port->port); } goto exit; } @@ -582,7 +548,7 @@ static void mct_u232_read_int_callback(struct urb *urb) /* Record Control Line states */ mct_u232_msr_to_state(port, &priv->control_state, priv->last_msr); - mct_u232_msr_to_icount(&priv->icount, priv->last_msr); + mct_u232_msr_to_icount(&port->icount, priv->last_msr); #if 0 /* Not yet handled. See belkin_sa.c for further information */ @@ -610,7 +576,7 @@ static void mct_u232_read_int_callback(struct urb *urb) tty_kref_put(tty); } #endif - wake_up_interruptible(&priv->msr_wait); + wake_up_interruptible(&port->port.delta_msr_wait); spin_unlock_irqrestore(&priv->lock, flags); exit: retval = usb_submit_urb(urb, GFP_ATOMIC); @@ -798,82 +764,6 @@ static void mct_u232_unthrottle(struct tty_struct *tty) } } -static int mct_u232_ioctl(struct tty_struct *tty, - unsigned int cmd, unsigned long arg) -{ - DEFINE_WAIT(wait); - struct usb_serial_port *port = tty->driver_data; - struct mct_u232_private *mct_u232_port = usb_get_serial_port_data(port); - struct async_icount cnow, cprev; - unsigned long flags; - - dev_dbg(&port->dev, "%s - cmd = 0x%x\n", __func__, cmd); - - switch (cmd) { - - case TIOCMIWAIT: - - dev_dbg(&port->dev, "%s TIOCMIWAIT", __func__); - - spin_lock_irqsave(&mct_u232_port->lock, flags); - cprev = mct_u232_port->icount; - spin_unlock_irqrestore(&mct_u232_port->lock, flags); - for ( ; ; ) { - prepare_to_wait(&mct_u232_port->msr_wait, - &wait, TASK_INTERRUPTIBLE); - schedule(); - finish_wait(&mct_u232_port->msr_wait, &wait); - /* see if a signal did it */ - if (signal_pending(current)) - return -ERESTARTSYS; - spin_lock_irqsave(&mct_u232_port->lock, flags); - cnow = mct_u232_port->icount; - spin_unlock_irqrestore(&mct_u232_port->lock, flags); - if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr && - cnow.dcd == cprev.dcd && cnow.cts == cprev.cts) - return -EIO; /* no change => error */ - if (((arg & TIOCM_RNG) && (cnow.rng != cprev.rng)) || - ((arg & TIOCM_DSR) && (cnow.dsr != cprev.dsr)) || - ((arg & TIOCM_CD) && (cnow.dcd != cprev.dcd)) || - ((arg & TIOCM_CTS) && (cnow.cts != cprev.cts))) { - return 0; - } - cprev = cnow; - } - - } - return -ENOIOCTLCMD; -} - -static int mct_u232_get_icount(struct tty_struct *tty, - struct serial_icounter_struct *icount) -{ - struct usb_serial_port *port = tty->driver_data; - struct mct_u232_private *mct_u232_port = usb_get_serial_port_data(port); - struct async_icount *ic = &mct_u232_port->icount; - unsigned long flags; - - spin_lock_irqsave(&mct_u232_port->lock, flags); - - icount->cts = ic->cts; - icount->dsr = ic->dsr; - icount->rng = ic->rng; - icount->dcd = ic->dcd; - icount->rx = ic->rx; - icount->tx = ic->tx; - icount->frame = ic->frame; - icount->overrun = ic->overrun; - icount->parity = ic->parity; - icount->brk = ic->brk; - icount->buf_overrun = ic->buf_overrun; - - spin_unlock_irqrestore(&mct_u232_port->lock, flags); - - dev_dbg(&port->dev, "%s TIOCGICOUNT RX=%d, TX=%d\n", - __func__, icount->rx, icount->tx); - return 0; -} - module_usb_serial_driver(serial_drivers, id_table); MODULE_AUTHOR(DRIVER_AUTHOR); diff --git a/drivers/usb/serial/metro-usb.c b/drivers/usb/serial/metro-usb.c index 3d258448c29..39e683096e9 100644 --- a/drivers/usb/serial/metro-usb.c +++ b/drivers/usb/serial/metro-usb.c @@ -7,7 +7,6 @@ */ #include <linux/kernel.h> -#include <linux/init.h> #include <linux/tty.h> #include <linux/module.h> #include <linux/usb.h> @@ -43,7 +42,7 @@ struct metrousb_private { }; /* Device table list. */ -static struct usb_device_id id_table[] = { +static const struct usb_device_id id_table[] = { { USB_DEVICE(FOCUS_VENDOR_ID, FOCUS_PRODUCT_ID_BI) }, { USB_DEVICE(FOCUS_VENDOR_ID, FOCUS_PRODUCT_ID_UNI) }, { }, /* Terminating entry. */ @@ -54,7 +53,7 @@ MODULE_DEVICE_TABLE(usb, id_table); #define UNI_CMD_OPEN 0x80 #define UNI_CMD_CLOSE 0xFF -inline int metrousb_is_unidirectional_mode(struct usb_serial_port *port) +static inline int metrousb_is_unidirectional_mode(struct usb_serial_port *port) { __u16 product_id = le16_to_cpu( port->serial->dev->descriptor.idProduct); @@ -95,7 +94,6 @@ static void metrousb_read_int_callback(struct urb *urb) { struct usb_serial_port *port = urb->context; struct metrousb_private *metro_priv = usb_get_serial_port_data(port); - struct tty_struct *tty; unsigned char *data = urb->transfer_buffer; int throttled = 0; int result = 0; @@ -124,15 +122,13 @@ static void metrousb_read_int_callback(struct urb *urb) /* Set the data read from the usb port into the serial port buffer. */ - tty = tty_port_tty_get(&port->port); - if (tty && urb->actual_length) { + if (urb->actual_length) { /* Loop through the data copying each byte to the tty layer. */ - tty_insert_flip_string(tty, data, urb->actual_length); + tty_insert_flip_string(&port->port, data, urb->actual_length); /* Force the data to the tty layer. */ - tty_flip_buffer_push(tty); + tty_flip_buffer_push(&port->port); } - tty_kref_put(tty); /* Set any port variables. */ spin_lock_irqsave(&metro_priv->lock, flags); @@ -180,10 +176,7 @@ static void metrousb_cleanup(struct usb_serial_port *port) usb_unlink_urb(port->interrupt_in_urb); usb_kill_urb(port->interrupt_in_urb); - mutex_lock(&port->serial->disc_mutex); - if (!port->serial->disconnected) - metrousb_send_unidirectional_cmd(UNI_CMD_CLOSE, port); - mutex_unlock(&port->serial->disc_mutex); + metrousb_send_unidirectional_cmd(UNI_CMD_CLOSE, port); } static int metrousb_open(struct tty_struct *tty, struct usb_serial_port *port) @@ -230,8 +223,8 @@ static int metrousb_open(struct tty_struct *tty, struct usb_serial_port *port) result = metrousb_send_unidirectional_cmd(UNI_CMD_OPEN, port); if (result) { dev_err(&port->dev, - "%s - failed to configure device for port number=%d, error code=%d\n", - __func__, port->number, result); + "%s - failed to configure device, error code=%d\n", + __func__, result); goto exit; } diff --git a/drivers/usb/serial/mos7720.c b/drivers/usb/serial/mos7720.c index f57a6b1fe78..dfd728a263d 100644 --- a/drivers/usb/serial/mos7720.c +++ b/drivers/usb/serial/mos7720.c @@ -1,6 +1,6 @@ /* * mos7720.c - * Controls the Moschip 7720 usb to dual port serial convertor + * Controls the Moschip 7720 usb to dual port serial converter * * Copyright 2006 Moschip Semiconductor Tech. Ltd. * @@ -22,7 +22,6 @@ */ #include <linux/kernel.h> #include <linux/errno.h> -#include <linux/init.h> #include <linux/slab.h> #include <linux/tty.h> #include <linux/tty_driver.h> @@ -40,13 +39,13 @@ #define DRIVER_DESC "Moschip USB Serial Driver" /* default urb timeout */ -#define MOS_WDR_TIMEOUT (HZ * 5) +#define MOS_WDR_TIMEOUT 5000 #define MOS_MAX_PORT 0x02 #define MOS_WRITE 0x0E #define MOS_READ 0x0D -/* Interrupt Rotinue Defines */ +/* Interrupt Routines Defines */ #define SERIAL_IIR_RLS 0x06 #define SERIAL_IIR_RDA 0x04 #define SERIAL_IIR_CTI 0x0c @@ -62,7 +61,6 @@ struct moschip_port { __u8 shadowMCR; /* last MCR value received */ __u8 shadowMSR; /* last MSR value received */ char open; - struct async_icount icount; struct usb_serial_port *port; /* loop back to the owner */ struct urb *write_urb_pool[NUM_URBS]; }; @@ -91,6 +89,7 @@ struct urbtracker { struct list_head urblist_entry; struct kref ref_count; struct urb *urb; + struct usb_ctrlrequest *setup; }; enum mos7715_pp_modes { @@ -210,7 +209,7 @@ static int write_mos_reg(struct usb_serial *serial, unsigned int serial_portnum, index, NULL, 0, MOS_WDR_TIMEOUT); if (status < 0) dev_err(&usbdev->dev, - "mos7720: usb_control_msg() failed: %d", status); + "mos7720: usb_control_msg() failed: %d\n", status); return status; } @@ -228,11 +227,22 @@ static int read_mos_reg(struct usb_serial *serial, unsigned int serial_portnum, __u8 requesttype = (__u8)0xc0; __u16 index = get_reg_index(reg); __u16 value = get_reg_value(reg, serial_portnum); - int status = usb_control_msg(usbdev, pipe, request, requesttype, value, - index, data, 1, MOS_WDR_TIMEOUT); - if (status < 0) + u8 *buf; + int status; + + buf = kmalloc(1, GFP_KERNEL); + if (!buf) + return -ENOMEM; + + status = usb_control_msg(usbdev, pipe, request, requesttype, value, + index, buf, 1, MOS_WDR_TIMEOUT); + if (status == 1) + *data = *buf; + else if (status < 0) dev_err(&usbdev->dev, - "mos7720: usb_control_msg() failed: %d", status); + "mos7720: usb_control_msg() failed: %d\n", status); + kfree(buf); + return status; } @@ -261,6 +271,7 @@ static void destroy_urbtracker(struct kref *kref) struct mos7715_parport *mos_parport = urbtrack->mos_parport; usb_free_urb(urbtrack->urb); + kfree(urbtrack->setup); kfree(urbtrack); kref_put(&mos_parport->ref_count, destroy_mos_parport); } @@ -345,32 +356,35 @@ static int write_parport_reg_nonblock(struct mos7715_parport *mos_parport, struct urbtracker *urbtrack; int ret_val; unsigned long flags; - struct usb_ctrlrequest setup; struct usb_serial *serial = mos_parport->serial; struct usb_device *usbdev = serial->dev; /* create and initialize the control urb and containing urbtracker */ urbtrack = kmalloc(sizeof(struct urbtracker), GFP_ATOMIC); - if (urbtrack == NULL) { - dev_err(&usbdev->dev, "out of memory"); + if (!urbtrack) return -ENOMEM; - } + kref_get(&mos_parport->ref_count); urbtrack->mos_parport = mos_parport; urbtrack->urb = usb_alloc_urb(0, GFP_ATOMIC); - if (urbtrack->urb == NULL) { - dev_err(&usbdev->dev, "out of urbs"); + if (!urbtrack->urb) { kfree(urbtrack); return -ENOMEM; } - setup.bRequestType = (__u8)0x40; - setup.bRequest = (__u8)0x0e; - setup.wValue = get_reg_value(reg, dummy); - setup.wIndex = get_reg_index(reg); - setup.wLength = 0; + urbtrack->setup = kmalloc(sizeof(*urbtrack->setup), GFP_ATOMIC); + if (!urbtrack->setup) { + usb_free_urb(urbtrack->urb); + kfree(urbtrack); + return -ENOMEM; + } + urbtrack->setup->bRequestType = (__u8)0x40; + urbtrack->setup->bRequest = (__u8)0x0e; + urbtrack->setup->wValue = cpu_to_le16(get_reg_value(reg, dummy)); + urbtrack->setup->wIndex = cpu_to_le16(get_reg_index(reg)); + urbtrack->setup->wLength = 0; usb_fill_control_urb(urbtrack->urb, usbdev, usb_sndctrlpipe(usbdev, 0), - (unsigned char *)&setup, + (unsigned char *)urbtrack->setup, NULL, 0, async_complete, urbtrack); kref_init(&urbtrack->ref_count); INIT_LIST_HEAD(&urbtrack->urblist_entry); @@ -385,7 +399,7 @@ static int write_parport_reg_nonblock(struct mos7715_parport *mos_parport, &mos_parport->deferred_urbs); spin_unlock_irqrestore(&mos_parport->listlock, flags); tasklet_schedule(&mos_parport->urb_tasklet); - dev_dbg(&usbdev->dev, "tasklet scheduled"); + dev_dbg(&usbdev->dev, "tasklet scheduled\n"); return 0; } @@ -404,7 +418,7 @@ static int write_parport_reg_nonblock(struct mos7715_parport *mos_parport, mutex_unlock(&serial->disc_mutex); if (ret_val) { dev_err(&usbdev->dev, - "%s: submit_urb() failed: %d", __func__, ret_val); + "%s: submit_urb() failed: %d\n", __func__, ret_val); spin_lock_irqsave(&mos_parport->listlock, flags); list_del(&urbtrack->urblist_entry); spin_unlock_irqrestore(&mos_parport->listlock, flags); @@ -423,7 +437,7 @@ static int write_parport_reg_nonblock(struct mos7715_parport *mos_parport, * not called the release function yet because someone has a serial port open. * The shared release_lock prevents the first, and the mutex and disconnected * flag maintained by usbserial covers the second. We also use the msg_pending - * flag to ensure that all synchronous usb messgage calls have completed before + * flag to ensure that all synchronous usb message calls have completed before * our release function can return. */ static int parport_prologue(struct parport *pp) @@ -438,7 +452,7 @@ static int parport_prologue(struct parport *pp) return -1; } mos_parport->msg_pending = true; /* synch usb call pending */ - INIT_COMPLETION(mos_parport->syncmsg_compl); + reinit_completion(&mos_parport->syncmsg_compl); spin_unlock(&release_lock); mutex_lock(&mos_parport->serial->disc_mutex); @@ -454,7 +468,7 @@ static int parport_prologue(struct parport *pp) } /* - * This is the the common bottom part of all parallel port functions that send + * This is the common bottom part of all parallel port functions that send * synchronous messages to the device. */ static inline void parport_epilogue(struct parport *pp) @@ -642,7 +656,7 @@ static size_t parport_mos7715_write_compat(struct parport *pp, parport_epilogue(pp); if (retval) { dev_err(&mos_parport->serial->dev->dev, - "mos7720: usb_bulk_msg() failed: %d", retval); + "mos7720: usb_bulk_msg() failed: %d\n", retval); return 0; } return actual_len; @@ -685,10 +699,9 @@ static int mos7715_parport_init(struct usb_serial *serial) /* allocate and initialize parallel port control struct */ mos_parport = kzalloc(sizeof(struct mos7715_parport), GFP_KERNEL); - if (mos_parport == NULL) { - dev_dbg(&serial->dev->dev, "%s: kzalloc failed\n", __func__); + if (!mos_parport) return -ENOMEM; - } + mos_parport->msg_pending = false; kref_init(&mos_parport->ref_count); spin_lock_init(&mos_parport->listlock); @@ -862,7 +875,7 @@ static void mos7715_interrupt_callback(struct urb *urb) if (!(iir & 0x01)) { /* serial port interrupt pending */ switch (iir & 0x0f) { case SERIAL_IIR_RLS: - dev_dbg(dev, "Serial Port: Receiver status error or address bit detected in 9-bit mode\n\n"); + dev_dbg(dev, "Serial Port: Receiver status error or address bit detected in 9-bit mode\n"); break; case SERIAL_IIR_CTI: dev_dbg(dev, "Serial Port: Receiver time out\n"); @@ -899,7 +912,6 @@ static void mos7720_bulk_in_callback(struct urb *urb) int retval; unsigned char *data ; struct usb_serial_port *port; - struct tty_struct *tty; int status = urb->status; if (status) { @@ -913,12 +925,10 @@ static void mos7720_bulk_in_callback(struct urb *urb) data = urb->transfer_buffer; - tty = tty_port_tty_get(&port->port); - if (tty && urb->actual_length) { - tty_insert_flip_string(tty, data, urb->actual_length); - tty_flip_buffer_push(tty); + if (urb->actual_length) { + tty_insert_flip_string(&port->port, data, urb->actual_length); + tty_flip_buffer_push(&port->port); } - tty_kref_put(tty); if (port->read_urb->status != -EINPROGRESS) { retval = usb_submit_urb(port->read_urb, GFP_ATOMIC); @@ -935,7 +945,6 @@ static void mos7720_bulk_in_callback(struct urb *urb) static void mos7720_bulk_out_data_callback(struct urb *urb) { struct moschip_port *mos7720_port; - struct tty_struct *tty; int status = urb->status; if (status) { @@ -949,11 +958,8 @@ static void mos7720_bulk_out_data_callback(struct urb *urb) return ; } - tty = tty_port_tty_get(&mos7720_port->port->port); - - if (tty && mos7720_port->open) - tty_wakeup(tty); - tty_kref_put(tty); + if (mos7720_port->open) + tty_port_tty_wakeup(&mos7720_port->port->port); } /* @@ -1008,18 +1014,12 @@ static int mos7720_open(struct tty_struct *tty, struct usb_serial_port *port) for (j = 0; j < NUM_URBS; ++j) { urb = usb_alloc_urb(0, GFP_KERNEL); mos7720_port->write_urb_pool[j] = urb; - - if (urb == NULL) { - dev_err(&port->dev, "No more urbs???\n"); + if (!urb) continue; - } urb->transfer_buffer = kmalloc(URB_TRANSFER_BUFFER_SIZE, GFP_KERNEL); if (!urb->transfer_buffer) { - dev_err(&port->dev, - "%s-out of memory for urb buffers.\n", - __func__); usb_free_urb(mos7720_port->write_urb_pool[j]); mos7720_port->write_urb_pool[j] = NULL; continue; @@ -1044,7 +1044,7 @@ static int mos7720_open(struct tty_struct *tty, struct usb_serial_port *port) * * 0x08 : SP1/2 Control Reg */ - port_number = port->number - port->serial->minor; + port_number = port->port_number; read_mos_reg(serial, port_number, LSR, &data); dev_dbg(&port->dev, "SS::%p LSR:%x\n", mos7720_port, data); @@ -1063,7 +1063,7 @@ static int mos7720_open(struct tty_struct *tty, struct usb_serial_port *port) write_mos_reg(serial, port_number, SP_CONTROL_REG, 0x00); read_mos_reg(serial, dummy, SP_CONTROL_REG, &data); - data = data | (port->number - port->serial->minor + 1); + data = data | (port->port_number + 1); write_mos_reg(serial, dummy, SP_CONTROL_REG, data); mos7720_port->shadowLCR = 0x83; write_mos_reg(serial, port_number, LCR, mos7720_port->shadowLCR); @@ -1078,9 +1078,6 @@ static int mos7720_open(struct tty_struct *tty, struct usb_serial_port *port) dev_err(&port->dev, "%s - Error %d submitting read urb\n", __func__, response); - /* initialize our icount structure */ - memset(&(mos7720_port->icount), 0x00, sizeof(mos7720_port->icount)); - /* initialize our port settings */ mos7720_port->shadowMCR = UART_MCR_OUT2; /* Must set to enable ints! */ @@ -1147,16 +1144,9 @@ static void mos7720_close(struct usb_serial_port *port) usb_kill_urb(port->write_urb); usb_kill_urb(port->read_urb); - mutex_lock(&serial->disc_mutex); - /* these commands must not be issued if the device has - * been disconnected */ - if (!serial->disconnected) { - write_mos_reg(serial, port->number - port->serial->minor, - MCR, 0x00); - write_mos_reg(serial, port->number - port->serial->minor, - IER, 0x00); - } - mutex_unlock(&serial->disc_mutex); + write_mos_reg(serial, port->port_number, MCR, 0x00); + write_mos_reg(serial, port->port_number, IER, 0x00); + mos7720_port->open = 0; } @@ -1179,8 +1169,7 @@ static void mos7720_break(struct tty_struct *tty, int break_state) data = mos7720_port->shadowLCR & ~UART_LCR_SBC; mos7720_port->shadowLCR = data; - write_mos_reg(serial, port->number - port->serial->minor, - LCR, mos7720_port->shadowLCR); + write_mos_reg(serial, port->port_number, LCR, mos7720_port->shadowLCR); } /* @@ -1251,11 +1240,8 @@ static int mos7720_write(struct tty_struct *tty, struct usb_serial_port *port, if (urb->transfer_buffer == NULL) { urb->transfer_buffer = kmalloc(URB_TRANSFER_BUFFER_SIZE, GFP_KERNEL); - if (urb->transfer_buffer == NULL) { - dev_err_console(port, "%s no more kernel memory...\n", - __func__); + if (!urb->transfer_buffer) goto exit; - } } transfer_size = min(count, URB_TRANSFER_BUFFER_SIZE); @@ -1311,8 +1297,8 @@ static void mos7720_throttle(struct tty_struct *tty) /* if we are implementing RTS/CTS, toggle that line */ if (tty->termios.c_cflag & CRTSCTS) { mos7720_port->shadowMCR &= ~UART_MCR_RTS; - write_mos_reg(port->serial, port->number - port->serial->minor, - MCR, mos7720_port->shadowMCR); + write_mos_reg(port->serial, port->port_number, MCR, + mos7720_port->shadowMCR); if (status != 0) return; } @@ -1343,8 +1329,8 @@ static void mos7720_unthrottle(struct tty_struct *tty) /* if we are implementing RTS/CTS, toggle that line */ if (tty->termios.c_cflag & CRTSCTS) { mos7720_port->shadowMCR |= UART_MCR_RTS; - write_mos_reg(port->serial, port->number - port->serial->minor, - MCR, mos7720_port->shadowMCR); + write_mos_reg(port->serial, port->port_number, MCR, + mos7720_port->shadowMCR); if (status != 0) return; } @@ -1368,7 +1354,7 @@ static int set_higher_rates(struct moschip_port *mos7720_port, * Init Sequence for higher rates ***********************************************/ dev_dbg(&port->dev, "Sending Setting Commands ..........\n"); - port_number = port->number - port->serial->minor; + port_number = port->port_number; write_mos_reg(serial, port_number, IER, 0x00); write_mos_reg(serial, port_number, FCR, 0x00); @@ -1494,7 +1480,7 @@ static int send_cmd_write_baud_rate(struct moschip_port *mos7720_port, port = mos7720_port->port; serial = port->serial; - number = port->number - port->serial->minor; + number = port->port_number; dev_dbg(&port->dev, "%s - baud = %d\n", __func__, baudrate); /* Calculate the Divisor */ @@ -1545,7 +1531,7 @@ static void change_port_settings(struct tty_struct *tty, port = mos7720_port->port; serial = port->serial; - port_number = port->number - port->serial->minor; + port_number = port->port_number; if (!mos7720_port->open) { dev_dbg(&port->dev, "%s - port not opened\n", __func__); @@ -1636,7 +1622,7 @@ static void change_port_settings(struct tty_struct *tty, mos7720_port->shadowMCR |= (UART_MCR_XONANY); /* To set hardware flow control to the specified * * serial port, in SP1/2_CONTROL_REG */ - if (port->number) + if (port_number) write_mos_reg(serial, dummy, SP_CONTROL_REG, 0x01); else write_mos_reg(serial, dummy, SP_CONTROL_REG, 0x02); @@ -1738,7 +1724,7 @@ static int get_lsr_info(struct tty_struct *tty, struct usb_serial_port *port = tty->driver_data; unsigned int result = 0; unsigned char data = 0; - int port_number = port->number - port->serial->minor; + int port_number = port->port_number; int count; count = mos7720_chars_in_buffer(tty); @@ -1800,39 +1786,12 @@ static int mos7720_tiocmset(struct tty_struct *tty, mcr &= ~UART_MCR_LOOP; mos7720_port->shadowMCR = mcr; - write_mos_reg(port->serial, port->number - port->serial->minor, - MCR, mos7720_port->shadowMCR); + write_mos_reg(port->serial, port->port_number, MCR, + mos7720_port->shadowMCR); return 0; } -static int mos7720_get_icount(struct tty_struct *tty, - struct serial_icounter_struct *icount) -{ - struct usb_serial_port *port = tty->driver_data; - struct moschip_port *mos7720_port; - struct async_icount cnow; - - mos7720_port = usb_get_serial_port_data(port); - cnow = mos7720_port->icount; - - icount->cts = cnow.cts; - icount->dsr = cnow.dsr; - icount->rng = cnow.rng; - icount->dcd = cnow.dcd; - icount->rx = cnow.rx; - icount->tx = cnow.tx; - icount->frame = cnow.frame; - icount->overrun = cnow.overrun; - icount->parity = cnow.parity; - icount->brk = cnow.brk; - icount->buf_overrun = cnow.buf_overrun; - - dev_dbg(&port->dev, "%s TIOCGICOUNT RX=%d, TX=%d\n", __func__, - icount->rx, icount->tx); - return 0; -} - static int set_modem_info(struct moschip_port *mos7720_port, unsigned int cmd, unsigned int __user *value) { @@ -1872,8 +1831,8 @@ static int set_modem_info(struct moschip_port *mos7720_port, unsigned int cmd, } mos7720_port->shadowMCR = mcr; - write_mos_reg(port->serial, port->number - port->serial->minor, - MCR, mos7720_port->shadowMCR); + write_mos_reg(port->serial, port->port_number, MCR, + mos7720_port->shadowMCR); return 0; } @@ -1889,8 +1848,8 @@ static int get_serial_info(struct moschip_port *mos7720_port, memset(&tmp, 0, sizeof(tmp)); tmp.type = PORT_16550A; - tmp.line = mos7720_port->port->serial->minor; - tmp.port = mos7720_port->port->number; + tmp.line = mos7720_port->port->minor; + tmp.port = mos7720_port->port->port_number; tmp.irq = 0; tmp.flags = ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ; tmp.xmit_fifo_size = NUM_URBS * URB_TRANSFER_BUFFER_SIZE; @@ -1908,15 +1867,11 @@ static int mos7720_ioctl(struct tty_struct *tty, { struct usb_serial_port *port = tty->driver_data; struct moschip_port *mos7720_port; - struct async_icount cnow; - struct async_icount cprev; mos7720_port = usb_get_serial_port_data(port); if (mos7720_port == NULL) return -ENODEV; - dev_dbg(&port->dev, "%s - cmd = 0x%x", __func__, cmd); - switch (cmd) { case TIOCSERGETLSR: dev_dbg(&port->dev, "%s TIOCSERGETLSR\n", __func__); @@ -1934,27 +1889,6 @@ static int mos7720_ioctl(struct tty_struct *tty, dev_dbg(&port->dev, "%s TIOCGSERIAL\n", __func__); return get_serial_info(mos7720_port, (struct serial_struct __user *)arg); - - case TIOCMIWAIT: - dev_dbg(&port->dev, "%s TIOCMIWAIT\n", __func__); - cprev = mos7720_port->icount; - while (1) { - if (signal_pending(current)) - return -ERESTARTSYS; - cnow = mos7720_port->icount; - if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr && - cnow.dcd == cprev.dcd && cnow.cts == cprev.cts) - return -EIO; /* no change => error */ - if (((arg & TIOCM_RNG) && (cnow.rng != cprev.rng)) || - ((arg & TIOCM_DSR) && (cnow.dsr != cprev.dsr)) || - ((arg & TIOCM_CD) && (cnow.dcd != cprev.dcd)) || - ((arg & TIOCM_CTS) && (cnow.cts != cprev.cts))) { - return 0; - } - cprev = cnow; - } - /* NOTREACHED */ - break; } return -ENOIOCTLCMD; @@ -1995,7 +1929,7 @@ static int mos7720_startup(struct usb_serial *serial) /* setting configuration feature to one */ usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0), - (__u8)0x03, 0x00, 0x01, 0x00, NULL, 0x00, 5*HZ); + (__u8)0x03, 0x00, 0x01, 0x00, NULL, 0x00, 5000); /* start the interrupt urb */ ret_val = usb_submit_urb(serial->port[0]->interrupt_in_urb, GFP_KERNEL); @@ -2038,7 +1972,7 @@ static void mos7720_release(struct usb_serial *serial) /* wait for synchronous usb calls to return */ if (mos_parport->msg_pending) wait_for_completion_timeout(&mos_parport->syncmsg_compl, - MOS_WDR_TIMEOUT); + msecs_to_jiffies(MOS_WDR_TIMEOUT)); parport_remove_port(mos_parport->pp); usb_set_serial_data(serial, NULL); @@ -2110,7 +2044,6 @@ static struct usb_serial_driver moschip7720_2port_driver = { .ioctl = mos7720_ioctl, .tiocmget = mos7720_tiocmget, .tiocmset = mos7720_tiocmset, - .get_icount = mos7720_get_icount, .set_termios = mos7720_set_termios, .write = mos7720_write, .write_room = mos7720_write_room, diff --git a/drivers/usb/serial/mos7840.c b/drivers/usb/serial/mos7840.c index 66d9e088d9d..393be562d87 100644 --- a/drivers/usb/serial/mos7840.c +++ b/drivers/usb/serial/mos7840.c @@ -24,7 +24,6 @@ #include <linux/kernel.h> #include <linux/errno.h> -#include <linux/init.h> #include <linux/slab.h> #include <linux/tty.h> #include <linux/tty_driver.h> @@ -183,7 +182,10 @@ #define LED_ON_MS 500 #define LED_OFF_MS 500 -static int device_type; +enum mos7840_flag { + MOS7840_FLAG_CTRL_BUSY, + MOS7840_FLAG_LED_BUSY, +}; static const struct usb_device_id id_table[] = { {USB_DEVICE(USB_VENDOR_ID_MOSCHIP, MOSCHIP_DEVICE_ID_7840)}, @@ -218,10 +220,6 @@ struct moschip_port { __u8 shadowMCR; /* last MCR value received */ char open; char open_ports; - wait_queue_head_t wait_chase; /* for handling sleeping while waiting for chase to finish */ - wait_queue_head_t delta_msr_wait; /* for handling sleeping while waiting for msr change to happen */ - int delta_msr_cond; - struct async_icount icount; struct usb_serial_port *port; /* loop back to the owner of this object */ /* Offsets */ @@ -241,9 +239,12 @@ struct moschip_port { /* For device(s) with LED indicator */ bool has_led; - bool led_flag; struct timer_list led_timer1; /* Timer for LED on */ struct timer_list led_timer2; /* Timer for LED off */ + struct urb *led_urb; + struct usb_ctrlrequest *led_dr; + + unsigned long flags; }; /* @@ -306,15 +307,12 @@ static int mos7840_set_uart_reg(struct usb_serial_port *port, __u16 reg, /* For the UART control registers, the application number need to be Or'ed */ if (port->serial->num_ports == 4) { - val |= (((__u16) port->number - - (__u16) (port->serial->minor)) + 1) << 8; + val |= ((__u16)port->port_number + 1) << 8; } else { - if (((__u16) port->number - (__u16) (port->serial->minor)) == 0) { - val |= (((__u16) port->number - - (__u16) (port->serial->minor)) + 1) << 8; + if (port->port_number == 0) { + val |= ((__u16)port->port_number + 1) << 8; } else { - val |= (((__u16) port->number - - (__u16) (port->serial->minor)) + 2) << 8; + val |= ((__u16)port->port_number + 2) << 8; } } dev_dbg(&port->dev, "%s application number is %x\n", __func__, val); @@ -343,16 +341,12 @@ static int mos7840_get_uart_reg(struct usb_serial_port *port, __u16 reg, /* Wval is same as application number */ if (port->serial->num_ports == 4) { - Wval = - (((__u16) port->number - (__u16) (port->serial->minor)) + - 1) << 8; + Wval = ((__u16)port->port_number + 1) << 8; } else { - if (((__u16) port->number - (__u16) (port->serial->minor)) == 0) { - Wval = (((__u16) port->number - - (__u16) (port->serial->minor)) + 1) << 8; + if (port->port_number == 0) { + Wval = ((__u16)port->port_number + 1) << 8; } else { - Wval = (((__u16) port->number - - (__u16) (port->serial->minor)) + 2) << 8; + Wval = ((__u16)port->port_number + 2) << 8; } } dev_dbg(&port->dev, "%s application number is %x\n", __func__, Wval); @@ -400,29 +394,22 @@ static void mos7840_handle_new_msr(struct moschip_port *port, __u8 new_msr) struct moschip_port *mos7840_port; struct async_icount *icount; mos7840_port = port; - icount = &mos7840_port->icount; if (new_msr & (MOS_MSR_DELTA_CTS | MOS_MSR_DELTA_DSR | MOS_MSR_DELTA_RI | MOS_MSR_DELTA_CD)) { - icount = &mos7840_port->icount; + icount = &mos7840_port->port->icount; /* update input line counters */ - if (new_msr & MOS_MSR_DELTA_CTS) { + if (new_msr & MOS_MSR_DELTA_CTS) icount->cts++; - smp_wmb(); - } - if (new_msr & MOS_MSR_DELTA_DSR) { + if (new_msr & MOS_MSR_DELTA_DSR) icount->dsr++; - smp_wmb(); - } - if (new_msr & MOS_MSR_DELTA_CD) { + if (new_msr & MOS_MSR_DELTA_CD) icount->dcd++; - smp_wmb(); - } - if (new_msr & MOS_MSR_DELTA_RI) { + if (new_msr & MOS_MSR_DELTA_RI) icount->rng++; - smp_wmb(); - } + + wake_up_interruptible(&port->port->port.delta_msr_wait); } } @@ -440,23 +427,15 @@ static void mos7840_handle_new_lsr(struct moschip_port *port, __u8 new_lsr) } /* update input line counters */ - icount = &port->icount; - if (new_lsr & SERIAL_LSR_BI) { + icount = &port->port->icount; + if (new_lsr & SERIAL_LSR_BI) icount->brk++; - smp_wmb(); - } - if (new_lsr & SERIAL_LSR_OE) { + if (new_lsr & SERIAL_LSR_OE) icount->overrun++; - smp_wmb(); - } - if (new_lsr & SERIAL_LSR_PE) { + if (new_lsr & SERIAL_LSR_PE) icount->parity++; - smp_wmb(); - } - if (new_lsr & SERIAL_LSR_FE) { + if (new_lsr & SERIAL_LSR_FE) icount->frame++; - smp_wmb(); - } } /************************************************************************/ @@ -485,10 +464,10 @@ static void mos7840_control_callback(struct urb *urb) case -ESHUTDOWN: /* this urb is terminated, clean up */ dev_dbg(dev, "%s - urb shutting down with status: %d\n", __func__, status); - return; + goto out; default: dev_dbg(dev, "%s - nonzero urb status received: %d\n", __func__, status); - return; + goto out; } dev_dbg(dev, "%s urb buffer size is %d\n", __func__, urb->actual_length); @@ -501,6 +480,8 @@ static void mos7840_control_callback(struct urb *urb) mos7840_handle_new_msr(mos7840_port, regval); else if (mos7840_port->MsrLsr == 1) mos7840_handle_new_lsr(mos7840_port, regval); +out: + clear_bit_unlock(MOS7840_FLAG_CTRL_BUSY, &mos7840_port->flags); } static int mos7840_get_reg(struct moschip_port *mcs, __u16 Wval, __u16 reg, @@ -511,6 +492,9 @@ static int mos7840_get_reg(struct moschip_port *mcs, __u16 Wval, __u16 reg, unsigned char *buffer = mcs->ctrl_buf; int ret; + if (test_and_set_bit_lock(MOS7840_FLAG_CTRL_BUSY, &mcs->flags)) + return -EBUSY; + dr->bRequestType = MCS_RD_RTYPE; dr->bRequest = MCS_RDREQ; dr->wValue = cpu_to_le16(Wval); /* 0 */ @@ -522,6 +506,9 @@ static int mos7840_get_reg(struct moschip_port *mcs, __u16 Wval, __u16 reg, mos7840_control_callback, mcs); mcs->control_urb->transfer_buffer_length = 2; ret = usb_submit_urb(mcs->control_urb, GFP_ATOMIC); + if (ret) + clear_bit_unlock(MOS7840_FLAG_CTRL_BUSY, &mcs->flags); + return ret; } @@ -535,11 +522,11 @@ static void mos7840_set_led_callback(struct urb *urb) case -ENOENT: case -ESHUTDOWN: /* This urb is terminated, clean up */ - dev_dbg(&urb->dev->dev, "%s - urb shutting down with status: %d", + dev_dbg(&urb->dev->dev, "%s - urb shutting down: %d\n", __func__, urb->status); break; default: - dev_dbg(&urb->dev->dev, "%s - nonzero urb status received: %d", + dev_dbg(&urb->dev->dev, "%s - nonzero urb status: %d\n", __func__, urb->status); } } @@ -548,7 +535,7 @@ static void mos7840_set_led_async(struct moschip_port *mcs, __u16 wval, __u16 reg) { struct usb_device *dev = mcs->port->serial->dev; - struct usb_ctrlrequest *dr = mcs->dr; + struct usb_ctrlrequest *dr = mcs->led_dr; dr->bRequestType = MCS_WR_RTYPE; dr->bRequest = MCS_WRREQ; @@ -556,10 +543,10 @@ static void mos7840_set_led_async(struct moschip_port *mcs, __u16 wval, dr->wIndex = cpu_to_le16(reg); dr->wLength = cpu_to_le16(0); - usb_fill_control_urb(mcs->control_urb, dev, usb_sndctrlpipe(dev, 0), + usb_fill_control_urb(mcs->led_urb, dev, usb_sndctrlpipe(dev, 0), (unsigned char *)dr, NULL, 0, mos7840_set_led_callback, NULL); - usb_submit_urb(mcs->control_urb, GFP_ATOMIC); + usb_submit_urb(mcs->led_urb, GFP_ATOMIC); } static void mos7840_set_led_sync(struct usb_serial_port *port, __u16 reg, @@ -585,7 +572,19 @@ static void mos7840_led_flag_off(unsigned long arg) { struct moschip_port *mcs = (struct moschip_port *) arg; - mcs->led_flag = false; + clear_bit_unlock(MOS7840_FLAG_LED_BUSY, &mcs->flags); +} + +static void mos7840_led_activity(struct usb_serial_port *port) +{ + struct moschip_port *mos7840_port = usb_get_serial_port_data(port); + + if (test_and_set_bit_lock(MOS7840_FLAG_LED_BUSY, &mos7840_port->flags)) + return; + + mos7840_set_led_async(mos7840_port, 0x0301, MODEM_CONTROL_REGISTER); + mod_timer(&mos7840_port->led_timer1, + jiffies + msecs_to_jiffies(LED_ON_MS)); } /***************************************************************************** @@ -649,9 +648,7 @@ static void mos7840_interrupt_callback(struct urb *urb) for (i = 0; i < serial->num_ports; i++) { mos7840_port = mos7840_get_port_private(serial->port[i]); - wval = - (((__u16) serial->port[i]->number - - (__u16) (serial->minor)) + 1) << 8; + wval = ((__u16)serial->port[i]->port_number + 1) << 8; if (mos7840_port->open) { if (sp[i] & 0x01) { dev_dbg(&urb->dev->dev, "SP%d No Interrupt !!!\n", i); @@ -744,7 +741,6 @@ static void mos7840_bulk_in_callback(struct urb *urb) struct usb_serial *serial; struct usb_serial_port *port; struct moschip_port *mos7840_port; - struct tty_struct *tty; int status = urb->status; mos7840_port = urb->context; @@ -773,15 +769,11 @@ static void mos7840_bulk_in_callback(struct urb *urb) usb_serial_debug_data(&port->dev, __func__, urb->actual_length, data); if (urb->actual_length) { - tty = tty_port_tty_get(&mos7840_port->port->port); - if (tty) { - tty_insert_flip_string(tty, data, urb->actual_length); - tty_flip_buffer_push(tty); - tty_kref_put(tty); - } - mos7840_port->icount.rx += urb->actual_length; - smp_wmb(); - dev_dbg(&port->dev, "mos7840_port->icount.rx is %d:\n", mos7840_port->icount.rx); + struct tty_port *tport = &mos7840_port->port->port; + tty_insert_flip_string(tport, data, urb->actual_length); + tty_flip_buffer_push(tport); + port->icount.rx += urb->actual_length; + dev_dbg(&port->dev, "icount.rx is %d:\n", port->icount.rx); } if (!mos7840_port->read_urb) { @@ -790,14 +782,8 @@ static void mos7840_bulk_in_callback(struct urb *urb) return; } - /* Turn on LED */ - if (mos7840_port->has_led && !mos7840_port->led_flag) { - mos7840_port->led_flag = true; - mos7840_set_led_async(mos7840_port, 0x0301, - MODEM_CONTROL_REGISTER); - mod_timer(&mos7840_port->led_timer1, - jiffies + msecs_to_jiffies(LED_ON_MS)); - } + if (mos7840_port->has_led) + mos7840_led_activity(port); mos7840_port->read_urb_busy = true; retval = usb_submit_urb(mos7840_port->read_urb, GFP_ATOMIC); @@ -818,7 +804,6 @@ static void mos7840_bulk_out_data_callback(struct urb *urb) { struct moschip_port *mos7840_port; struct usb_serial_port *port; - struct tty_struct *tty; int status = urb->status; int i; @@ -841,28 +826,14 @@ static void mos7840_bulk_out_data_callback(struct urb *urb) if (mos7840_port_paranoia_check(port, __func__)) return; - tty = tty_port_tty_get(&port->port); - if (tty && mos7840_port->open) - tty_wakeup(tty); - tty_kref_put(tty); + if (mos7840_port->open) + tty_port_tty_wakeup(&port->port); } /************************************************************************/ /* D R I V E R T T Y I N T E R F A C E F U N C T I O N S */ /************************************************************************/ -#ifdef MCSSerialProbe -static int mos7840_serial_probe(struct usb_serial *serial, - const struct usb_device_id *id) -{ - - /*need to implement the mode_reg reading and updating\ - structures usb_serial_ device_type\ - (i.e num_ports, num_bulkin,bulkout etc) */ - /* Also we can update the changes attach */ - return 1; -} -#endif /***************************************************************************** * mos7840_open @@ -904,20 +875,14 @@ static int mos7840_open(struct tty_struct *tty, struct usb_serial_port *port) for (j = 0; j < NUM_URBS; ++j) { urb = usb_alloc_urb(0, GFP_KERNEL); mos7840_port->write_urb_pool[j] = urb; - - if (urb == NULL) { - dev_err(&port->dev, "No more urbs???\n"); + if (!urb) continue; - } urb->transfer_buffer = kmalloc(URB_TRANSFER_BUFFER_SIZE, GFP_KERNEL); if (!urb->transfer_buffer) { usb_free_urb(urb); mos7840_port->write_urb_pool[j] = NULL; - dev_err(&port->dev, - "%s-out of memory for urb buffers.\n", - __func__); continue; } } @@ -940,20 +905,20 @@ static int mos7840_open(struct tty_struct *tty, struct usb_serial_port *port) status = mos7840_get_reg_sync(port, mos7840_port->SpRegOffset, &Data); if (status < 0) { dev_dbg(&port->dev, "Reading Spreg failed\n"); - return -1; + goto err; } Data |= 0x80; status = mos7840_set_reg_sync(port, mos7840_port->SpRegOffset, Data); if (status < 0) { dev_dbg(&port->dev, "writing Spreg failed\n"); - return -1; + goto err; } Data &= ~0x80; status = mos7840_set_reg_sync(port, mos7840_port->SpRegOffset, Data); if (status < 0) { dev_dbg(&port->dev, "writing Spreg failed\n"); - return -1; + goto err; } /* End of block to be checked */ @@ -962,7 +927,7 @@ static int mos7840_open(struct tty_struct *tty, struct usb_serial_port *port) &Data); if (status < 0) { dev_dbg(&port->dev, "Reading Controlreg failed\n"); - return -1; + goto err; } Data |= 0x08; /* Driver done bit */ Data |= 0x20; /* rx_disable */ @@ -970,7 +935,7 @@ static int mos7840_open(struct tty_struct *tty, struct usb_serial_port *port) mos7840_port->ControlRegOffset, Data); if (status < 0) { dev_dbg(&port->dev, "writing Controlreg failed\n"); - return -1; + goto err; } /* do register settings here */ /* Set all regs to the device default values. */ @@ -981,21 +946,21 @@ static int mos7840_open(struct tty_struct *tty, struct usb_serial_port *port) status = mos7840_set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data); if (status < 0) { dev_dbg(&port->dev, "disabling interrupts failed\n"); - return -1; + goto err; } /* Set FIFO_CONTROL_REGISTER to the default value */ Data = 0x00; status = mos7840_set_uart_reg(port, FIFO_CONTROL_REGISTER, Data); if (status < 0) { dev_dbg(&port->dev, "Writing FIFO_CONTROL_REGISTER failed\n"); - return -1; + goto err; } Data = 0xcf; status = mos7840_set_uart_reg(port, FIFO_CONTROL_REGISTER, Data); if (status < 0) { dev_dbg(&port->dev, "Writing FIFO_CONTROL_REGISTER failed\n"); - return -1; + goto err; } Data = 0x03; @@ -1091,8 +1056,8 @@ static int mos7840_open(struct tty_struct *tty, struct usb_serial_port *port) * (can't set it up in mos7840_startup as the * * structures were not set up at that time.) */ - dev_dbg(&port->dev, "port number is %d\n", port->number); - dev_dbg(&port->dev, "serial number is %d\n", port->serial->minor); + dev_dbg(&port->dev, "port number is %d\n", port->port_number); + dev_dbg(&port->dev, "minor number is %d\n", port->minor); dev_dbg(&port->dev, "Bulkin endpoint is %d\n", port->bulk_in_endpointAddress); dev_dbg(&port->dev, "BulkOut endpoint is %d\n", port->bulk_out_endpointAddress); dev_dbg(&port->dev, "Interrupt endpoint is %d\n", port->interrupt_in_endpointAddress); @@ -1100,9 +1065,7 @@ static int mos7840_open(struct tty_struct *tty, struct usb_serial_port *port) mos7840_port->read_urb = port->read_urb; /* set up our bulk in urb */ - if ((serial->num_ports == 2) - && ((((__u16)port->number - - (__u16)(port->serial->minor)) % 2) != 0)) { + if ((serial->num_ports == 2) && (((__u16)port->port_number % 2) != 0)) { usb_fill_bulk_urb(mos7840_port->read_urb, serial->dev, usb_rcvbulkpipe(serial->dev, @@ -1129,23 +1092,23 @@ static int mos7840_open(struct tty_struct *tty, struct usb_serial_port *port) mos7840_port->read_urb_busy = false; } - /* initialize our wait queues */ - init_waitqueue_head(&mos7840_port->wait_chase); - init_waitqueue_head(&mos7840_port->delta_msr_wait); - - /* initialize our icount structure */ - memset(&(mos7840_port->icount), 0x00, sizeof(mos7840_port->icount)); - /* initialize our port settings */ /* Must set to enable ints! */ mos7840_port->shadowMCR = MCR_MASTER_IE; /* send a open port command */ mos7840_port->open = 1; /* mos7840_change_port_settings(mos7840_port,old_termios); */ - mos7840_port->icount.tx = 0; - mos7840_port->icount.rx = 0; return 0; +err: + for (j = 0; j < NUM_URBS; ++j) { + urb = mos7840_port->write_urb_pool[j]; + if (!urb) + continue; + kfree(urb->transfer_buffer); + usb_free_urb(urb); + } + return status; } /***************************************************************************** @@ -1226,27 +1189,12 @@ static void mos7840_close(struct usb_serial_port *port) } } - /* While closing port, shutdown all bulk read, write * - * and interrupt read if they exists */ - if (serial->dev) { - if (mos7840_port->write_urb) { - dev_dbg(&port->dev, "%s", "Shutdown bulk write\n"); - usb_kill_urb(mos7840_port->write_urb); - } - if (mos7840_port->read_urb) { - dev_dbg(&port->dev, "%s", "Shutdown bulk read\n"); - usb_kill_urb(mos7840_port->read_urb); - mos7840_port->read_urb_busy = false; - } - if ((&mos7840_port->control_urb)) { - dev_dbg(&port->dev, "%s", "Shutdown control read\n"); - /*/ usb_kill_urb (mos7840_port->control_urb); */ - } - } -/* if(mos7840_port->ctrl_buf != NULL) */ -/* kfree(mos7840_port->ctrl_buf); */ + usb_kill_urb(mos7840_port->write_urb); + usb_kill_urb(mos7840_port->read_urb); + mos7840_port->read_urb_busy = false; + port0->open_ports--; - dev_dbg(&port->dev, "%s in close%d:in port%d\n", __func__, port0->open_ports, port->number); + dev_dbg(&port->dev, "%s in close%d\n", __func__, port0->open_ports); if (port0->open_ports == 0) { if (serial->port[0]->interrupt_in_urb) { dev_dbg(&port->dev, "Shutdown interrupt_in_urb\n"); @@ -1256,8 +1204,7 @@ static void mos7840_close(struct usb_serial_port *port) if (mos7840_port->write_urb) { /* if this urb had a transfer buffer already (old tx) free it */ - if (mos7840_port->write_urb->transfer_buffer != NULL) - kfree(mos7840_port->write_urb->transfer_buffer); + kfree(mos7840_port->write_urb->transfer_buffer); usb_free_urb(mos7840_port->write_urb); } @@ -1270,47 +1217,6 @@ static void mos7840_close(struct usb_serial_port *port) mos7840_port->open = 0; } -/************************************************************************ - * - * mos7840_block_until_chase_response - * - * This function will block the close until one of the following: - * 1. Response to our Chase comes from mos7840 - * 2. A timeout of 10 seconds without activity has expired - * (1K of mos7840 data @ 2400 baud ==> 4 sec to empty) - * - ************************************************************************/ - -static void mos7840_block_until_chase_response(struct tty_struct *tty, - struct moschip_port *mos7840_port) -{ - int timeout = msecs_to_jiffies(1000); - int wait = 10; - int count; - - while (1) { - count = mos7840_chars_in_buffer(tty); - - /* Check for Buffer status */ - if (count <= 0) - return; - - /* Block the thread for a while */ - interruptible_sleep_on_timeout(&mos7840_port->wait_chase, - timeout); - /* No activity.. count down section */ - wait--; - if (wait == 0) { - dev_dbg(&mos7840_port->port->dev, "%s - TIMEOUT\n", __func__); - return; - } else { - /* Reset timeout value back to seconds */ - wait = 10; - } - } - -} - /***************************************************************************** * mos7840_break * this function sends a break to the port @@ -1334,10 +1240,6 @@ static void mos7840_break(struct tty_struct *tty, int break_state) if (mos7840_port == NULL) return; - if (serial->dev) - /* flush and block until tx is empty */ - mos7840_block_until_chase_response(tty, mos7840_port); - if (break_state == -1) data = mos7840_port->shadowLCR | LCR_SET_BREAK; else @@ -1472,21 +1374,15 @@ static int mos7840_write(struct tty_struct *tty, struct usb_serial_port *port, if (urb->transfer_buffer == NULL) { urb->transfer_buffer = kmalloc(URB_TRANSFER_BUFFER_SIZE, GFP_KERNEL); - - if (urb->transfer_buffer == NULL) { - dev_err_console(port, "%s no more kernel memory...\n", - __func__); + if (!urb->transfer_buffer) goto exit; - } } transfer_size = min(count, URB_TRANSFER_BUFFER_SIZE); memcpy(urb->transfer_buffer, current_position, transfer_size); /* fill urb with data and submit */ - if ((serial->num_ports == 2) - && ((((__u16)port->number - - (__u16)(port->serial->minor)) % 2) != 0)) { + if ((serial->num_ports == 2) && (((__u16)port->port_number % 2) != 0)) { usb_fill_bulk_urb(urb, serial->dev, usb_sndbulkpipe(serial->dev, @@ -1507,13 +1403,8 @@ static int mos7840_write(struct tty_struct *tty, struct usb_serial_port *port, data1 = urb->transfer_buffer; dev_dbg(&port->dev, "bulkout endpoint is %d\n", port->bulk_out_endpointAddress); - /* Turn on LED */ - if (mos7840_port->has_led && !mos7840_port->led_flag) { - mos7840_port->led_flag = true; - mos7840_set_led_sync(port, MODEM_CONTROL_REGISTER, 0x0301); - mod_timer(&mos7840_port->led_timer1, - jiffies + msecs_to_jiffies(LED_ON_MS)); - } + if (mos7840_port->has_led) + mos7840_led_activity(port); /* send it down the pipe */ status = usb_submit_urb(urb, GFP_ATOMIC); @@ -1526,9 +1417,8 @@ static int mos7840_write(struct tty_struct *tty, struct usb_serial_port *port, goto exit; } bytes_sent = transfer_size; - mos7840_port->icount.tx += transfer_size; - smp_wmb(); - dev_dbg(&port->dev, "mos7840_port->icount.tx is %d:\n", mos7840_port->icount.tx); + port->icount.tx += transfer_size; + dev_dbg(&port->dev, "icount.tx is %d:\n", port->icount.tx); exit: return bytes_sent; @@ -1631,7 +1521,11 @@ static int mos7840_tiocmget(struct tty_struct *tty) return -ENODEV; status = mos7840_get_uart_reg(port, MODEM_STATUS_REGISTER, &msr); + if (status != 1) + return -EIO; status = mos7840_get_uart_reg(port, MODEM_CONTROL_REGISTER, &mcr); + if (status != 1) + return -EIO; result = ((mcr & MCR_DTR) ? TIOCM_DTR : 0) | ((mcr & MCR_RTS) ? TIOCM_RTS : 0) | ((mcr & MCR_LOOPBACK) ? TIOCM_LOOP : 0) @@ -1782,10 +1676,9 @@ static int mos7840_send_cmd_write_baud_rate(struct moschip_port *mos7840_port, if (mos7840_serial_paranoia_check(port->serial, __func__)) return -1; - number = mos7840_port->port->number - mos7840_port->port->serial->minor; + number = mos7840_port->port->port_number; - dev_dbg(&port->dev, "%s - port = %d, baud = %d\n", __func__, - mos7840_port->port->number, baudRate); + dev_dbg(&port->dev, "%s - baud = %d\n", __func__, baudRate); /* reset clk_uart_sel in spregOffset */ if (baudRate > 115200) { #ifdef HW_flow_control @@ -1909,25 +1802,25 @@ static void mos7840_change_port_settings(struct tty_struct *tty, iflag = tty->termios.c_iflag; /* Change the number of bits */ - if (cflag & CSIZE) { - switch (cflag & CSIZE) { - case CS5: - lData = LCR_BITS_5; - break; + switch (cflag & CSIZE) { + case CS5: + lData = LCR_BITS_5; + break; - case CS6: - lData = LCR_BITS_6; - break; + case CS6: + lData = LCR_BITS_6; + break; - case CS7: - lData = LCR_BITS_7; - break; - default: - case CS8: - lData = LCR_BITS_8; - break; - } + case CS7: + lData = LCR_BITS_7; + break; + + default: + case CS8: + lData = LCR_BITS_8; + break; } + /* Change the Parity bit */ if (cflag & PARENB) { if (cflag & PARODD) { @@ -2021,8 +1914,6 @@ static void mos7840_change_port_settings(struct tty_struct *tty, mos7840_port->read_urb_busy = false; } } - wake_up(&mos7840_port->delta_msr_wait); - mos7840_port->delta_msr_cond = 1; dev_dbg(&port->dev, "%s - mos7840_port->shadowLCR is End %x\n", __func__, mos7840_port->shadowLCR); } @@ -2068,7 +1959,6 @@ static void mos7840_set_termios(struct tty_struct *tty, tty->termios.c_cflag, RELEVANT_IFLAG(tty->termios.c_iflag)); dev_dbg(&port->dev, "%s - old clfag %08x old iflag %08x\n", __func__, old_termios->c_cflag, RELEVANT_IFLAG(old_termios->c_iflag)); - dev_dbg(&port->dev, "%s - port %d\n", __func__, port->number); /* change the port settings to the new ones specified */ @@ -2135,8 +2025,8 @@ static int mos7840_get_serial_info(struct moschip_port *mos7840_port, memset(&tmp, 0, sizeof(tmp)); tmp.type = PORT_16550A; - tmp.line = mos7840_port->port->serial->minor; - tmp.port = mos7840_port->port->number; + tmp.line = mos7840_port->port->minor; + tmp.port = mos7840_port->port->port_number; tmp.irq = 0; tmp.flags = ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ; tmp.xmit_fifo_size = NUM_URBS * URB_TRANSFER_BUFFER_SIZE; @@ -2149,34 +2039,6 @@ static int mos7840_get_serial_info(struct moschip_port *mos7840_port, return 0; } -static int mos7840_get_icount(struct tty_struct *tty, - struct serial_icounter_struct *icount) -{ - struct usb_serial_port *port = tty->driver_data; - struct moschip_port *mos7840_port; - struct async_icount cnow; - - mos7840_port = mos7840_get_port_private(port); - cnow = mos7840_port->icount; - - smp_rmb(); - icount->cts = cnow.cts; - icount->dsr = cnow.dsr; - icount->rng = cnow.rng; - icount->dcd = cnow.dcd; - icount->rx = cnow.rx; - icount->tx = cnow.tx; - icount->frame = cnow.frame; - icount->overrun = cnow.overrun; - icount->parity = cnow.parity; - icount->brk = cnow.brk; - icount->buf_overrun = cnow.buf_overrun; - - dev_dbg(&port->dev, "%s TIOCGICOUNT RX=%d, TX=%d\n", __func__, - icount->rx, icount->tx); - return 0; -} - /***************************************************************************** * SerialIoctl * this function handles any ioctl calls to the driver @@ -2189,9 +2051,6 @@ static int mos7840_ioctl(struct tty_struct *tty, void __user *argp = (void __user *)arg; struct moschip_port *mos7840_port; - struct async_icount cnow; - struct async_icount cprev; - if (mos7840_port_paranoia_check(port, __func__)) return -1; @@ -2200,8 +2059,6 @@ static int mos7840_ioctl(struct tty_struct *tty, if (mos7840_port == NULL) return -1; - dev_dbg(&port->dev, "%s - cmd = 0x%x\n", __func__, cmd); - switch (cmd) { /* return number of bytes available */ @@ -2216,36 +2073,6 @@ static int mos7840_ioctl(struct tty_struct *tty, case TIOCSSERIAL: dev_dbg(&port->dev, "%s TIOCSSERIAL\n", __func__); break; - - case TIOCMIWAIT: - dev_dbg(&port->dev, "%s TIOCMIWAIT\n", __func__); - cprev = mos7840_port->icount; - while (1) { - /* interruptible_sleep_on(&mos7840_port->delta_msr_wait); */ - mos7840_port->delta_msr_cond = 0; - wait_event_interruptible(mos7840_port->delta_msr_wait, - (mos7840_port-> - delta_msr_cond == 1)); - - /* see if a signal did it */ - if (signal_pending(current)) - return -ERESTARTSYS; - cnow = mos7840_port->icount; - smp_rmb(); - if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr && - cnow.dcd == cprev.dcd && cnow.cts == cprev.cts) - return -EIO; /* no change => error */ - if (((arg & TIOCM_RNG) && (cnow.rng != cprev.rng)) || - ((arg & TIOCM_DSR) && (cnow.dsr != cprev.dsr)) || - ((arg & TIOCM_CD) && (cnow.dcd != cprev.dcd)) || - ((arg & TIOCM_CTS) && (cnow.cts != cprev.cts))) { - return 0; - } - cprev = cnow; - } - /* NOTREACHED */ - break; - default: break; } @@ -2255,13 +2082,21 @@ static int mos7840_ioctl(struct tty_struct *tty, static int mos7810_check(struct usb_serial *serial) { int i, pass_count = 0; + u8 *buf; __u16 data = 0, mcr_data = 0; __u16 test_pattern = 0x55AA; + int res; + + buf = kmalloc(VENDOR_READ_LENGTH, GFP_KERNEL); + if (!buf) + return 0; /* failed to identify 7810 */ /* Store MCR setting */ - usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0), + res = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0), MCS_RDREQ, MCS_RD_RTYPE, 0x0300, MODEM_CONTROL_REGISTER, - &mcr_data, VENDOR_READ_LENGTH, MOS_WDR_TIMEOUT); + buf, VENDOR_READ_LENGTH, MOS_WDR_TIMEOUT); + if (res == VENDOR_READ_LENGTH) + mcr_data = *buf; for (i = 0; i < 16; i++) { /* Send the 1-bit test pattern out to MCS7810 test pin */ @@ -2271,9 +2106,12 @@ static int mos7810_check(struct usb_serial *serial) MODEM_CONTROL_REGISTER, NULL, 0, MOS_WDR_TIMEOUT); /* Read the test pattern back */ - usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0), - MCS_RDREQ, MCS_RD_RTYPE, 0, GPIO_REGISTER, &data, - VENDOR_READ_LENGTH, MOS_WDR_TIMEOUT); + res = usb_control_msg(serial->dev, + usb_rcvctrlpipe(serial->dev, 0), MCS_RDREQ, + MCS_RD_RTYPE, 0, GPIO_REGISTER, buf, + VENDOR_READ_LENGTH, MOS_WDR_TIMEOUT); + if (res == VENDOR_READ_LENGTH) + data = *buf; /* If this is a MCS7810 device, both test patterns must match */ if (((test_pattern >> i) ^ (~data >> 1)) & 0x0001) @@ -2287,38 +2125,56 @@ static int mos7810_check(struct usb_serial *serial) MCS_WR_RTYPE, 0x0300 | mcr_data, MODEM_CONTROL_REGISTER, NULL, 0, MOS_WDR_TIMEOUT); + kfree(buf); + if (pass_count == 16) return 1; return 0; } -static int mos7840_calc_num_ports(struct usb_serial *serial) +static int mos7840_probe(struct usb_serial *serial, + const struct usb_device_id *id) { - __u16 data = 0x00; - int mos7840_num_ports; + u16 product = le16_to_cpu(serial->dev->descriptor.idProduct); + u8 *buf; + int device_type; + + if (product == MOSCHIP_DEVICE_ID_7810 || + product == MOSCHIP_DEVICE_ID_7820) { + device_type = product; + goto out; + } + + buf = kzalloc(VENDOR_READ_LENGTH, GFP_KERNEL); + if (!buf) + return -ENOMEM; usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0), - MCS_RDREQ, MCS_RD_RTYPE, 0, GPIO_REGISTER, &data, - VENDOR_READ_LENGTH, MOS_WDR_TIMEOUT); + MCS_RDREQ, MCS_RD_RTYPE, 0, GPIO_REGISTER, buf, + VENDOR_READ_LENGTH, MOS_WDR_TIMEOUT); - if (serial->dev->descriptor.idProduct == MOSCHIP_DEVICE_ID_7810 || - serial->dev->descriptor.idProduct == MOSCHIP_DEVICE_ID_7820) { - device_type = serial->dev->descriptor.idProduct; - } else { - /* For a MCS7840 device GPIO0 must be set to 1 */ - if ((data & 0x01) == 1) - device_type = MOSCHIP_DEVICE_ID_7840; - else if (mos7810_check(serial)) - device_type = MOSCHIP_DEVICE_ID_7810; - else - device_type = MOSCHIP_DEVICE_ID_7820; - } + /* For a MCS7840 device GPIO0 must be set to 1 */ + if (buf[0] & 0x01) + device_type = MOSCHIP_DEVICE_ID_7840; + else if (mos7810_check(serial)) + device_type = MOSCHIP_DEVICE_ID_7810; + else + device_type = MOSCHIP_DEVICE_ID_7820; + + kfree(buf); +out: + usb_set_serial_data(serial, (void *)(unsigned long)device_type); + + return 0; +} + +static int mos7840_calc_num_ports(struct usb_serial *serial) +{ + int device_type = (unsigned long)usb_get_serial_data(serial); + int mos7840_num_ports; mos7840_num_ports = (device_type >> 4) & 0x000F; - serial->num_bulk_in = mos7840_num_ports; - serial->num_bulk_out = mos7840_num_ports; - serial->num_ports = mos7840_num_ports; return mos7840_num_ports; } @@ -2326,6 +2182,7 @@ static int mos7840_calc_num_ports(struct usb_serial *serial) static int mos7840_port_probe(struct usb_serial_port *port) { struct usb_serial *serial = port->serial; + int device_type = (unsigned long)usb_get_serial_data(serial); struct moschip_port *mos7840_port; int status; int pnum; @@ -2334,14 +2191,12 @@ static int mos7840_port_probe(struct usb_serial_port *port) /* we set up the pointers to the endpoints in the mos7840_open * * function, as the structures aren't created yet. */ - pnum = port->number - serial->minor; + pnum = port->port_number; dev_dbg(&port->dev, "mos7840_startup: configuring port %d\n", pnum); mos7840_port = kzalloc(sizeof(struct moschip_port), GFP_KERNEL); - if (mos7840_port == NULL) { - dev_err(&port->dev, "%s - Out of memory\n", __func__); + if (!mos7840_port) return -ENOMEM; - } /* Initialize all port interrupt end point to port 0 int * endpoint. Our device has only one interrupt end point @@ -2355,10 +2210,8 @@ static int mos7840_port_probe(struct usb_serial_port *port) * usb-serial.c:get_free_serial() and cannot therefore be used * to index device instances */ mos7840_port->port_num = pnum + 1; - dev_dbg(&port->dev, "port->number = %d\n", port->number); - dev_dbg(&port->dev, "port->serial->minor = %d\n", port->serial->minor); + dev_dbg(&port->dev, "port->minor = %d\n", port->minor); dev_dbg(&port->dev, "mos7840_port->port_num = %d\n", mos7840_port->port_num); - dev_dbg(&port->dev, "serial->minor = %d\n", serial->minor); if (mos7840_port->port_num == 1) { mos7840_port->SpRegOffset = 0x0; @@ -2503,6 +2356,14 @@ static int mos7840_port_probe(struct usb_serial_port *port) if (device_type == MOSCHIP_DEVICE_ID_7810) { mos7840_port->has_led = true; + mos7840_port->led_urb = usb_alloc_urb(0, GFP_KERNEL); + mos7840_port->led_dr = kmalloc(sizeof(*mos7840_port->led_dr), + GFP_KERNEL); + if (!mos7840_port->led_urb || !mos7840_port->led_dr) { + status = -ENOMEM; + goto error; + } + init_timer(&mos7840_port->led_timer1); mos7840_port->led_timer1.function = mos7840_led_off; mos7840_port->led_timer1.expires = @@ -2515,8 +2376,6 @@ static int mos7840_port_probe(struct usb_serial_port *port) jiffies + msecs_to_jiffies(LED_OFF_MS); mos7840_port->led_timer2.data = (unsigned long)mos7840_port; - mos7840_port->led_flag = false; - /* Turn off LED */ mos7840_set_led_sync(port, MODEM_CONTROL_REGISTER, 0x0300); } @@ -2538,6 +2397,8 @@ out: } return 0; error: + kfree(mos7840_port->led_dr); + usb_free_urb(mos7840_port->led_urb); kfree(mos7840_port->dr); kfree(mos7840_port->ctrl_buf); usb_free_urb(mos7840_port->control_urb); @@ -2558,6 +2419,10 @@ static int mos7840_port_remove(struct usb_serial_port *port) del_timer_sync(&mos7840_port->led_timer1); del_timer_sync(&mos7840_port->led_timer2); + + usb_kill_urb(mos7840_port->led_urb); + usb_free_urb(mos7840_port->led_urb); + kfree(mos7840_port->led_dr); } usb_kill_urb(mos7840_port->control_urb); usb_free_urb(mos7840_port->control_urb); @@ -2584,15 +2449,14 @@ static struct usb_serial_driver moschip7840_4port_device = { .throttle = mos7840_throttle, .unthrottle = mos7840_unthrottle, .calc_num_ports = mos7840_calc_num_ports, -#ifdef MCSSerialProbe - .probe = mos7840_serial_probe, -#endif + .probe = mos7840_probe, .ioctl = mos7840_ioctl, .set_termios = mos7840_set_termios, .break_ctl = mos7840_break, .tiocmget = mos7840_tiocmget, .tiocmset = mos7840_tiocmset, - .get_icount = mos7840_get_icount, + .tiocmiwait = usb_serial_generic_tiocmiwait, + .get_icount = usb_serial_generic_get_icount, .port_probe = mos7840_port_probe, .port_remove = mos7840_port_remove, .read_bulk_callback = mos7840_bulk_in_callback, diff --git a/drivers/usb/serial/moto_modem.c b/drivers/usb/serial/moto_modem.c deleted file mode 100644 index c5ff6c7795a..00000000000 --- a/drivers/usb/serial/moto_modem.c +++ /dev/null @@ -1,48 +0,0 @@ -/* - * Motorola USB Phone driver - * - * Copyright (C) 2008 Greg Kroah-Hartman <greg@kroah.com> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - * {sigh} - * Motorola should be using the CDC ACM USB spec, but instead - * they try to just "do their own thing"... This driver should handle a - * few phones in which a basic "dumb serial connection" is needed to be - * able to get a connection through to them. - */ - -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/tty.h> -#include <linux/module.h> -#include <linux/usb.h> -#include <linux/usb/serial.h> - -static const struct usb_device_id id_table[] = { - { USB_DEVICE(0x05c6, 0x3197) }, /* unknown Motorola phone */ - { USB_DEVICE(0x0c44, 0x0022) }, /* unknown Mororola phone */ - { USB_DEVICE(0x22b8, 0x2a64) }, /* Motorola KRZR K1m */ - { USB_DEVICE(0x22b8, 0x2c84) }, /* Motorola VE240 phone */ - { USB_DEVICE(0x22b8, 0x2c64) }, /* Motorola V950 phone */ - { }, -}; -MODULE_DEVICE_TABLE(usb, id_table); - -static struct usb_serial_driver moto_device = { - .driver = { - .owner = THIS_MODULE, - .name = "moto-modem", - }, - .id_table = id_table, - .num_ports = 1, -}; - -static struct usb_serial_driver * const serial_drivers[] = { - &moto_device, NULL -}; - -module_usb_serial_driver(serial_drivers, id_table); -MODULE_LICENSE("GPL"); diff --git a/drivers/usb/serial/mxuport.c b/drivers/usb/serial/mxuport.c new file mode 100644 index 00000000000..ab1d690274a --- /dev/null +++ b/drivers/usb/serial/mxuport.c @@ -0,0 +1,1393 @@ +/* + * mxuport.c - MOXA UPort series driver + * + * Copyright (c) 2006 Moxa Technologies Co., Ltd. + * Copyright (c) 2013 Andrew Lunn <andrew@lunn.ch> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * Supports the following Moxa USB to serial converters: + * 2 ports : UPort 1250, UPort 1250I + * 4 ports : UPort 1410, UPort 1450, UPort 1450I + * 8 ports : UPort 1610-8, UPort 1650-8 + * 16 ports : UPort 1610-16, UPort 1650-16 + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/firmware.h> +#include <linux/jiffies.h> +#include <linux/serial.h> +#include <linux/serial_reg.h> +#include <linux/slab.h> +#include <linux/tty.h> +#include <linux/tty_driver.h> +#include <linux/tty_flip.h> +#include <linux/uaccess.h> +#include <linux/usb.h> +#include <linux/usb/serial.h> +#include <asm/unaligned.h> + +/* Definitions for the vendor ID and device ID */ +#define MX_USBSERIAL_VID 0x110A +#define MX_UPORT1250_PID 0x1250 +#define MX_UPORT1251_PID 0x1251 +#define MX_UPORT1410_PID 0x1410 +#define MX_UPORT1450_PID 0x1450 +#define MX_UPORT1451_PID 0x1451 +#define MX_UPORT1618_PID 0x1618 +#define MX_UPORT1658_PID 0x1658 +#define MX_UPORT1613_PID 0x1613 +#define MX_UPORT1653_PID 0x1653 + +/* Definitions for USB info */ +#define HEADER_SIZE 4 +#define EVENT_LENGTH 8 +#define DOWN_BLOCK_SIZE 64 + +/* Definitions for firmware info */ +#define VER_ADDR_1 0x20 +#define VER_ADDR_2 0x24 +#define VER_ADDR_3 0x28 + +/* Definitions for USB vendor request */ +#define RQ_VENDOR_NONE 0x00 +#define RQ_VENDOR_SET_BAUD 0x01 /* Set baud rate */ +#define RQ_VENDOR_SET_LINE 0x02 /* Set line status */ +#define RQ_VENDOR_SET_CHARS 0x03 /* Set Xon/Xoff chars */ +#define RQ_VENDOR_SET_RTS 0x04 /* Set RTS */ +#define RQ_VENDOR_SET_DTR 0x05 /* Set DTR */ +#define RQ_VENDOR_SET_XONXOFF 0x06 /* Set auto Xon/Xoff */ +#define RQ_VENDOR_SET_RX_HOST_EN 0x07 /* Set RX host enable */ +#define RQ_VENDOR_SET_OPEN 0x08 /* Set open/close port */ +#define RQ_VENDOR_PURGE 0x09 /* Purge Rx/Tx buffer */ +#define RQ_VENDOR_SET_MCR 0x0A /* Set MCR register */ +#define RQ_VENDOR_SET_BREAK 0x0B /* Set Break signal */ + +#define RQ_VENDOR_START_FW_DOWN 0x0C /* Start firmware download */ +#define RQ_VENDOR_STOP_FW_DOWN 0x0D /* Stop firmware download */ +#define RQ_VENDOR_QUERY_FW_READY 0x0E /* Query if new firmware ready */ + +#define RQ_VENDOR_SET_FIFO_DISABLE 0x0F /* Set fifo disable */ +#define RQ_VENDOR_SET_INTERFACE 0x10 /* Set interface */ +#define RQ_VENDOR_SET_HIGH_PERFOR 0x11 /* Set hi-performance */ + +#define RQ_VENDOR_ERASE_BLOCK 0x12 /* Erase flash block */ +#define RQ_VENDOR_WRITE_PAGE 0x13 /* Write flash page */ +#define RQ_VENDOR_PREPARE_WRITE 0x14 /* Prepare write flash */ +#define RQ_VENDOR_CONFIRM_WRITE 0x15 /* Confirm write flash */ +#define RQ_VENDOR_LOCATE 0x16 /* Locate the device */ + +#define RQ_VENDOR_START_ROM_DOWN 0x17 /* Start firmware download */ +#define RQ_VENDOR_ROM_DATA 0x18 /* Rom file data */ +#define RQ_VENDOR_STOP_ROM_DOWN 0x19 /* Stop firmware download */ +#define RQ_VENDOR_FW_DATA 0x20 /* Firmware data */ + +#define RQ_VENDOR_RESET_DEVICE 0x23 /* Try to reset the device */ +#define RQ_VENDOR_QUERY_FW_CONFIG 0x24 + +#define RQ_VENDOR_GET_VERSION 0x81 /* Get firmware version */ +#define RQ_VENDOR_GET_PAGE 0x82 /* Read flash page */ +#define RQ_VENDOR_GET_ROM_PROC 0x83 /* Get ROM process state */ + +#define RQ_VENDOR_GET_INQUEUE 0x84 /* Data in input buffer */ +#define RQ_VENDOR_GET_OUTQUEUE 0x85 /* Data in output buffer */ + +#define RQ_VENDOR_GET_MSR 0x86 /* Get modem status register */ + +/* Definitions for UPort event type */ +#define UPORT_EVENT_NONE 0 /* None */ +#define UPORT_EVENT_TXBUF_THRESHOLD 1 /* Tx buffer threshold */ +#define UPORT_EVENT_SEND_NEXT 2 /* Send next */ +#define UPORT_EVENT_MSR 3 /* Modem status */ +#define UPORT_EVENT_LSR 4 /* Line status */ +#define UPORT_EVENT_MCR 5 /* Modem control */ + +/* Definitions for serial event type */ +#define SERIAL_EV_CTS 0x0008 /* CTS changed state */ +#define SERIAL_EV_DSR 0x0010 /* DSR changed state */ +#define SERIAL_EV_RLSD 0x0020 /* RLSD changed state */ + +/* Definitions for modem control event type */ +#define SERIAL_EV_XOFF 0x40 /* XOFF received */ + +/* Definitions for line control of communication */ +#define MX_WORDLENGTH_5 5 +#define MX_WORDLENGTH_6 6 +#define MX_WORDLENGTH_7 7 +#define MX_WORDLENGTH_8 8 + +#define MX_PARITY_NONE 0 +#define MX_PARITY_ODD 1 +#define MX_PARITY_EVEN 2 +#define MX_PARITY_MARK 3 +#define MX_PARITY_SPACE 4 + +#define MX_STOP_BITS_1 0 +#define MX_STOP_BITS_1_5 1 +#define MX_STOP_BITS_2 2 + +#define MX_RTS_DISABLE 0x0 +#define MX_RTS_ENABLE 0x1 +#define MX_RTS_HW 0x2 +#define MX_RTS_NO_CHANGE 0x3 /* Flag, not valid register value*/ + +#define MX_INT_RS232 0 +#define MX_INT_2W_RS485 1 +#define MX_INT_RS422 2 +#define MX_INT_4W_RS485 3 + +/* Definitions for holding reason */ +#define MX_WAIT_FOR_CTS 0x0001 +#define MX_WAIT_FOR_DSR 0x0002 +#define MX_WAIT_FOR_DCD 0x0004 +#define MX_WAIT_FOR_XON 0x0008 +#define MX_WAIT_FOR_START_TX 0x0010 +#define MX_WAIT_FOR_UNTHROTTLE 0x0020 +#define MX_WAIT_FOR_LOW_WATER 0x0040 +#define MX_WAIT_FOR_SEND_NEXT 0x0080 + +#define MX_UPORT_2_PORT BIT(0) +#define MX_UPORT_4_PORT BIT(1) +#define MX_UPORT_8_PORT BIT(2) +#define MX_UPORT_16_PORT BIT(3) + +/* This structure holds all of the local port information */ +struct mxuport_port { + u8 mcr_state; /* Last MCR state */ + u8 msr_state; /* Last MSR state */ + struct mutex mutex; /* Protects mcr_state */ + spinlock_t spinlock; /* Protects msr_state */ +}; + +/* Table of devices that work with this driver */ +static const struct usb_device_id mxuport_idtable[] = { + { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1250_PID), + .driver_info = MX_UPORT_2_PORT }, + { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1251_PID), + .driver_info = MX_UPORT_2_PORT }, + { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1410_PID), + .driver_info = MX_UPORT_4_PORT }, + { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1450_PID), + .driver_info = MX_UPORT_4_PORT }, + { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1451_PID), + .driver_info = MX_UPORT_4_PORT }, + { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1618_PID), + .driver_info = MX_UPORT_8_PORT }, + { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1658_PID), + .driver_info = MX_UPORT_8_PORT }, + { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1613_PID), + .driver_info = MX_UPORT_16_PORT }, + { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1653_PID), + .driver_info = MX_UPORT_16_PORT }, + {} /* Terminating entry */ +}; + +MODULE_DEVICE_TABLE(usb, mxuport_idtable); + +/* + * Add a four byte header containing the port number and the number of + * bytes of data in the message. Return the number of bytes in the + * buffer. + */ +static int mxuport_prepare_write_buffer(struct usb_serial_port *port, + void *dest, size_t size) +{ + u8 *buf = dest; + int count; + + count = kfifo_out_locked(&port->write_fifo, buf + HEADER_SIZE, + size - HEADER_SIZE, + &port->lock); + + put_unaligned_be16(port->port_number, buf); + put_unaligned_be16(count, buf + 2); + + dev_dbg(&port->dev, "%s - size %zd count %d\n", __func__, + size, count); + + return count + HEADER_SIZE; +} + +/* Read the given buffer in from the control pipe. */ +static int mxuport_recv_ctrl_urb(struct usb_serial *serial, + u8 request, u16 value, u16 index, + u8 *data, size_t size) +{ + int status; + + status = usb_control_msg(serial->dev, + usb_rcvctrlpipe(serial->dev, 0), + request, + (USB_DIR_IN | USB_TYPE_VENDOR | + USB_RECIP_DEVICE), value, index, + data, size, + USB_CTRL_GET_TIMEOUT); + if (status < 0) { + dev_err(&serial->interface->dev, + "%s - usb_control_msg failed (%d)\n", + __func__, status); + return status; + } + + if (status != size) { + dev_err(&serial->interface->dev, + "%s - short read (%d / %zd)\n", + __func__, status, size); + return -EIO; + } + + return status; +} + +/* Write the given buffer out to the control pipe. */ +static int mxuport_send_ctrl_data_urb(struct usb_serial *serial, + u8 request, + u16 value, u16 index, + u8 *data, size_t size) +{ + int status; + + status = usb_control_msg(serial->dev, + usb_sndctrlpipe(serial->dev, 0), + request, + (USB_DIR_OUT | USB_TYPE_VENDOR | + USB_RECIP_DEVICE), value, index, + data, size, + USB_CTRL_SET_TIMEOUT); + if (status < 0) { + dev_err(&serial->interface->dev, + "%s - usb_control_msg failed (%d)\n", + __func__, status); + return status; + } + + if (status != size) { + dev_err(&serial->interface->dev, + "%s - short write (%d / %zd)\n", + __func__, status, size); + return -EIO; + } + + return 0; +} + +/* Send a vendor request without any data */ +static int mxuport_send_ctrl_urb(struct usb_serial *serial, + u8 request, u16 value, u16 index) +{ + return mxuport_send_ctrl_data_urb(serial, request, value, index, + NULL, 0); +} + +/* + * mxuport_throttle - throttle function of driver + * + * This function is called by the tty driver when it wants to stop the + * data being read from the port. Since all the data comes over one + * bulk in endpoint, we cannot stop submitting urbs by setting + * port->throttle. Instead tell the device to stop sending us data for + * the port. + */ +static void mxuport_throttle(struct tty_struct *tty) +{ + struct usb_serial_port *port = tty->driver_data; + struct usb_serial *serial = port->serial; + + dev_dbg(&port->dev, "%s\n", __func__); + + mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_RX_HOST_EN, + 0, port->port_number); +} + +/* + * mxuport_unthrottle - unthrottle function of driver + * + * This function is called by the tty driver when it wants to resume + * the data being read from the port. Tell the device it can resume + * sending us received data from the port. + */ +static void mxuport_unthrottle(struct tty_struct *tty) +{ + + struct usb_serial_port *port = tty->driver_data; + struct usb_serial *serial = port->serial; + + dev_dbg(&port->dev, "%s\n", __func__); + + mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_RX_HOST_EN, + 1, port->port_number); +} + +/* + * Processes one chunk of data received for a port. Mostly a copy of + * usb_serial_generic_process_read_urb(). + */ +static void mxuport_process_read_urb_data(struct usb_serial_port *port, + char *data, int size) +{ + int i; + + if (!port->port.console || !port->sysrq) { + tty_insert_flip_string(&port->port, data, size); + } else { + for (i = 0; i < size; i++, data++) { + if (!usb_serial_handle_sysrq_char(port, *data)) + tty_insert_flip_char(&port->port, *data, + TTY_NORMAL); + } + } + tty_flip_buffer_push(&port->port); +} + +static void mxuport_msr_event(struct usb_serial_port *port, u8 buf[4]) +{ + struct mxuport_port *mxport = usb_get_serial_port_data(port); + u8 rcv_msr_hold = buf[2] & 0xF0; + u16 rcv_msr_event = get_unaligned_be16(buf); + unsigned long flags; + + if (rcv_msr_event == 0) + return; + + /* Update MSR status */ + spin_lock_irqsave(&mxport->spinlock, flags); + + dev_dbg(&port->dev, "%s - current MSR status = 0x%x\n", + __func__, mxport->msr_state); + + if (rcv_msr_hold & UART_MSR_CTS) { + mxport->msr_state |= UART_MSR_CTS; + dev_dbg(&port->dev, "%s - CTS high\n", __func__); + } else { + mxport->msr_state &= ~UART_MSR_CTS; + dev_dbg(&port->dev, "%s - CTS low\n", __func__); + } + + if (rcv_msr_hold & UART_MSR_DSR) { + mxport->msr_state |= UART_MSR_DSR; + dev_dbg(&port->dev, "%s - DSR high\n", __func__); + } else { + mxport->msr_state &= ~UART_MSR_DSR; + dev_dbg(&port->dev, "%s - DSR low\n", __func__); + } + + if (rcv_msr_hold & UART_MSR_DCD) { + mxport->msr_state |= UART_MSR_DCD; + dev_dbg(&port->dev, "%s - DCD high\n", __func__); + } else { + mxport->msr_state &= ~UART_MSR_DCD; + dev_dbg(&port->dev, "%s - DCD low\n", __func__); + } + spin_unlock_irqrestore(&mxport->spinlock, flags); + + if (rcv_msr_event & + (SERIAL_EV_CTS | SERIAL_EV_DSR | SERIAL_EV_RLSD)) { + + if (rcv_msr_event & SERIAL_EV_CTS) { + port->icount.cts++; + dev_dbg(&port->dev, "%s - CTS change\n", __func__); + } + + if (rcv_msr_event & SERIAL_EV_DSR) { + port->icount.dsr++; + dev_dbg(&port->dev, "%s - DSR change\n", __func__); + } + + if (rcv_msr_event & SERIAL_EV_RLSD) { + port->icount.dcd++; + dev_dbg(&port->dev, "%s - DCD change\n", __func__); + } + wake_up_interruptible(&port->port.delta_msr_wait); + } +} + +static void mxuport_lsr_event(struct usb_serial_port *port, u8 buf[4]) +{ + u8 lsr_event = buf[2]; + + if (lsr_event & UART_LSR_BI) { + port->icount.brk++; + dev_dbg(&port->dev, "%s - break error\n", __func__); + } + + if (lsr_event & UART_LSR_FE) { + port->icount.frame++; + dev_dbg(&port->dev, "%s - frame error\n", __func__); + } + + if (lsr_event & UART_LSR_PE) { + port->icount.parity++; + dev_dbg(&port->dev, "%s - parity error\n", __func__); + } + + if (lsr_event & UART_LSR_OE) { + port->icount.overrun++; + dev_dbg(&port->dev, "%s - overrun error\n", __func__); + } +} + +/* + * When something interesting happens, modem control lines XON/XOFF + * etc, the device sends an event. Process these events. + */ +static void mxuport_process_read_urb_event(struct usb_serial_port *port, + u8 buf[4], u32 event) +{ + dev_dbg(&port->dev, "%s - receive event : %04x\n", __func__, event); + + switch (event) { + case UPORT_EVENT_SEND_NEXT: + /* + * Sent as part of the flow control on device buffers. + * Not currently used. + */ + break; + case UPORT_EVENT_MSR: + mxuport_msr_event(port, buf); + break; + case UPORT_EVENT_LSR: + mxuport_lsr_event(port, buf); + break; + case UPORT_EVENT_MCR: + /* + * Event to indicate a change in XON/XOFF from the + * peer. Currently not used. We just continue + * sending the device data and it will buffer it if + * needed. This event could be used for flow control + * between the host and the device. + */ + break; + default: + dev_dbg(&port->dev, "Unexpected event\n"); + break; + } +} + +/* + * One URB can contain data for multiple ports. Demultiplex the data, + * checking the port exists, is opened and the message is valid. + */ +static void mxuport_process_read_urb_demux_data(struct urb *urb) +{ + struct usb_serial_port *port = urb->context; + struct usb_serial *serial = port->serial; + u8 *data = urb->transfer_buffer; + u8 *end = data + urb->actual_length; + struct usb_serial_port *demux_port; + u8 *ch; + u16 rcv_port; + u16 rcv_len; + + while (data < end) { + if (data + HEADER_SIZE > end) { + dev_warn(&port->dev, "%s - message with short header\n", + __func__); + return; + } + + rcv_port = get_unaligned_be16(data); + if (rcv_port >= serial->num_ports) { + dev_warn(&port->dev, "%s - message for invalid port\n", + __func__); + return; + } + + demux_port = serial->port[rcv_port]; + rcv_len = get_unaligned_be16(data + 2); + if (!rcv_len || data + HEADER_SIZE + rcv_len > end) { + dev_warn(&port->dev, "%s - short data\n", __func__); + return; + } + + if (test_bit(ASYNCB_INITIALIZED, &demux_port->port.flags)) { + ch = data + HEADER_SIZE; + mxuport_process_read_urb_data(demux_port, ch, rcv_len); + } else { + dev_dbg(&demux_port->dev, "%s - data for closed port\n", + __func__); + } + data += HEADER_SIZE + rcv_len; + } +} + +/* + * One URB can contain events for multiple ports. Demultiplex the event, + * checking the port exists, and is opened. + */ +static void mxuport_process_read_urb_demux_event(struct urb *urb) +{ + struct usb_serial_port *port = urb->context; + struct usb_serial *serial = port->serial; + u8 *data = urb->transfer_buffer; + u8 *end = data + urb->actual_length; + struct usb_serial_port *demux_port; + u8 *ch; + u16 rcv_port; + u16 rcv_event; + + while (data < end) { + if (data + EVENT_LENGTH > end) { + dev_warn(&port->dev, "%s - message with short event\n", + __func__); + return; + } + + rcv_port = get_unaligned_be16(data); + if (rcv_port >= serial->num_ports) { + dev_warn(&port->dev, "%s - message for invalid port\n", + __func__); + return; + } + + demux_port = serial->port[rcv_port]; + if (test_bit(ASYNCB_INITIALIZED, &demux_port->port.flags)) { + ch = data + HEADER_SIZE; + rcv_event = get_unaligned_be16(data + 2); + mxuport_process_read_urb_event(demux_port, ch, + rcv_event); + } else { + dev_dbg(&demux_port->dev, + "%s - event for closed port\n", __func__); + } + data += EVENT_LENGTH; + } +} + +/* + * This is called when we have received data on the bulk in + * endpoint. Depending on which port it was received on, it can + * contain serial data or events. + */ +static void mxuport_process_read_urb(struct urb *urb) +{ + struct usb_serial_port *port = urb->context; + struct usb_serial *serial = port->serial; + + if (port == serial->port[0]) + mxuport_process_read_urb_demux_data(urb); + + if (port == serial->port[1]) + mxuport_process_read_urb_demux_event(urb); +} + +/* + * Ask the device how many bytes it has queued to be sent out. If + * there are none, return true. + */ +static bool mxuport_tx_empty(struct usb_serial_port *port) +{ + struct usb_serial *serial = port->serial; + bool is_empty = true; + u32 txlen; + u8 *len_buf; + int err; + + len_buf = kzalloc(4, GFP_KERNEL); + if (!len_buf) + goto out; + + err = mxuport_recv_ctrl_urb(serial, RQ_VENDOR_GET_OUTQUEUE, 0, + port->port_number, len_buf, 4); + if (err < 0) + goto out; + + txlen = get_unaligned_be32(len_buf); + dev_dbg(&port->dev, "%s - tx len = %u\n", __func__, txlen); + + if (txlen != 0) + is_empty = false; + +out: + kfree(len_buf); + return is_empty; +} + +static int mxuport_set_mcr(struct usb_serial_port *port, u8 mcr_state) +{ + struct usb_serial *serial = port->serial; + int err; + + dev_dbg(&port->dev, "%s - %02x\n", __func__, mcr_state); + + err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_MCR, + mcr_state, port->port_number); + if (err) + dev_err(&port->dev, "%s - failed to change MCR\n", __func__); + + return err; +} + +static int mxuport_set_dtr(struct usb_serial_port *port, int on) +{ + struct mxuport_port *mxport = usb_get_serial_port_data(port); + struct usb_serial *serial = port->serial; + int err; + + mutex_lock(&mxport->mutex); + + err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_DTR, + !!on, port->port_number); + if (!err) { + if (on) + mxport->mcr_state |= UART_MCR_DTR; + else + mxport->mcr_state &= ~UART_MCR_DTR; + } + + mutex_unlock(&mxport->mutex); + + return err; +} + +static int mxuport_set_rts(struct usb_serial_port *port, u8 state) +{ + struct mxuport_port *mxport = usb_get_serial_port_data(port); + struct usb_serial *serial = port->serial; + int err; + u8 mcr_state; + + mutex_lock(&mxport->mutex); + mcr_state = mxport->mcr_state; + + switch (state) { + case MX_RTS_DISABLE: + mcr_state &= ~UART_MCR_RTS; + break; + case MX_RTS_ENABLE: + mcr_state |= UART_MCR_RTS; + break; + case MX_RTS_HW: + /* + * Do not update mxport->mcr_state when doing hardware + * flow control. + */ + break; + default: + /* + * Should not happen, but somebody might try passing + * MX_RTS_NO_CHANGE, which is not valid. + */ + err = -EINVAL; + goto out; + } + err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_RTS, + state, port->port_number); + if (!err) + mxport->mcr_state = mcr_state; + +out: + mutex_unlock(&mxport->mutex); + + return err; +} + +static void mxuport_dtr_rts(struct usb_serial_port *port, int on) +{ + struct mxuport_port *mxport = usb_get_serial_port_data(port); + u8 mcr_state; + int err; + + mutex_lock(&mxport->mutex); + mcr_state = mxport->mcr_state; + + if (on) + mcr_state |= (UART_MCR_RTS | UART_MCR_DTR); + else + mcr_state &= ~(UART_MCR_RTS | UART_MCR_DTR); + + err = mxuport_set_mcr(port, mcr_state); + if (!err) + mxport->mcr_state = mcr_state; + + mutex_unlock(&mxport->mutex); +} + +static int mxuport_tiocmset(struct tty_struct *tty, unsigned int set, + unsigned int clear) +{ + struct usb_serial_port *port = tty->driver_data; + struct mxuport_port *mxport = usb_get_serial_port_data(port); + int err; + u8 mcr_state; + + mutex_lock(&mxport->mutex); + mcr_state = mxport->mcr_state; + + if (set & TIOCM_RTS) + mcr_state |= UART_MCR_RTS; + + if (set & TIOCM_DTR) + mcr_state |= UART_MCR_DTR; + + if (clear & TIOCM_RTS) + mcr_state &= ~UART_MCR_RTS; + + if (clear & TIOCM_DTR) + mcr_state &= ~UART_MCR_DTR; + + err = mxuport_set_mcr(port, mcr_state); + if (!err) + mxport->mcr_state = mcr_state; + + mutex_unlock(&mxport->mutex); + + return err; +} + +static int mxuport_tiocmget(struct tty_struct *tty) +{ + struct mxuport_port *mxport; + struct usb_serial_port *port = tty->driver_data; + unsigned int result; + unsigned long flags; + unsigned int msr; + unsigned int mcr; + + mxport = usb_get_serial_port_data(port); + + mutex_lock(&mxport->mutex); + spin_lock_irqsave(&mxport->spinlock, flags); + + msr = mxport->msr_state; + mcr = mxport->mcr_state; + + spin_unlock_irqrestore(&mxport->spinlock, flags); + mutex_unlock(&mxport->mutex); + + result = (((mcr & UART_MCR_DTR) ? TIOCM_DTR : 0) | /* 0x002 */ + ((mcr & UART_MCR_RTS) ? TIOCM_RTS : 0) | /* 0x004 */ + ((msr & UART_MSR_CTS) ? TIOCM_CTS : 0) | /* 0x020 */ + ((msr & UART_MSR_DCD) ? TIOCM_CAR : 0) | /* 0x040 */ + ((msr & UART_MSR_RI) ? TIOCM_RI : 0) | /* 0x080 */ + ((msr & UART_MSR_DSR) ? TIOCM_DSR : 0)); /* 0x100 */ + + dev_dbg(&port->dev, "%s - 0x%04x\n", __func__, result); + + return result; +} + +static int mxuport_set_termios_flow(struct tty_struct *tty, + struct ktermios *old_termios, + struct usb_serial_port *port, + struct usb_serial *serial) +{ + u8 xon = START_CHAR(tty); + u8 xoff = STOP_CHAR(tty); + int enable; + int err; + u8 *buf; + u8 rts; + + buf = kmalloc(2, GFP_KERNEL); + if (!buf) + return -ENOMEM; + + /* S/W flow control settings */ + if (I_IXOFF(tty) || I_IXON(tty)) { + enable = 1; + buf[0] = xon; + buf[1] = xoff; + + err = mxuport_send_ctrl_data_urb(serial, RQ_VENDOR_SET_CHARS, + 0, port->port_number, + buf, 2); + if (err) + goto out; + + dev_dbg(&port->dev, "%s - XON = 0x%02x, XOFF = 0x%02x\n", + __func__, xon, xoff); + } else { + enable = 0; + } + + err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_XONXOFF, + enable, port->port_number); + if (err) + goto out; + + rts = MX_RTS_NO_CHANGE; + + /* H/W flow control settings */ + if (!old_termios || + C_CRTSCTS(tty) != (old_termios->c_cflag & CRTSCTS)) { + if (C_CRTSCTS(tty)) + rts = MX_RTS_HW; + else + rts = MX_RTS_ENABLE; + } + + if (C_BAUD(tty)) { + if (old_termios && (old_termios->c_cflag & CBAUD) == B0) { + /* Raise DTR and RTS */ + if (C_CRTSCTS(tty)) + rts = MX_RTS_HW; + else + rts = MX_RTS_ENABLE; + mxuport_set_dtr(port, 1); + } + } else { + /* Drop DTR and RTS */ + rts = MX_RTS_DISABLE; + mxuport_set_dtr(port, 0); + } + + if (rts != MX_RTS_NO_CHANGE) + err = mxuport_set_rts(port, rts); + +out: + kfree(buf); + return err; +} + +static void mxuport_set_termios(struct tty_struct *tty, + struct usb_serial_port *port, + struct ktermios *old_termios) +{ + struct usb_serial *serial = port->serial; + u8 *buf; + u8 data_bits; + u8 stop_bits; + u8 parity; + int baud; + int err; + + if (old_termios && + !tty_termios_hw_change(&tty->termios, old_termios) && + tty->termios.c_iflag == old_termios->c_iflag) { + dev_dbg(&port->dev, "%s - nothing to change\n", __func__); + return; + } + + buf = kmalloc(4, GFP_KERNEL); + if (!buf) + return; + + /* Set data bit of termios */ + switch (C_CSIZE(tty)) { + case CS5: + data_bits = MX_WORDLENGTH_5; + break; + case CS6: + data_bits = MX_WORDLENGTH_6; + break; + case CS7: + data_bits = MX_WORDLENGTH_7; + break; + case CS8: + default: + data_bits = MX_WORDLENGTH_8; + break; + } + + /* Set parity of termios */ + if (C_PARENB(tty)) { + if (C_CMSPAR(tty)) { + if (C_PARODD(tty)) + parity = MX_PARITY_MARK; + else + parity = MX_PARITY_SPACE; + } else { + if (C_PARODD(tty)) + parity = MX_PARITY_ODD; + else + parity = MX_PARITY_EVEN; + } + } else { + parity = MX_PARITY_NONE; + } + + /* Set stop bit of termios */ + if (C_CSTOPB(tty)) + stop_bits = MX_STOP_BITS_2; + else + stop_bits = MX_STOP_BITS_1; + + buf[0] = data_bits; + buf[1] = parity; + buf[2] = stop_bits; + buf[3] = 0; + + err = mxuport_send_ctrl_data_urb(serial, RQ_VENDOR_SET_LINE, + 0, port->port_number, buf, 4); + if (err) + goto out; + + err = mxuport_set_termios_flow(tty, old_termios, port, serial); + if (err) + goto out; + + baud = tty_get_baud_rate(tty); + if (!baud) + baud = 9600; + + /* Note: Little Endian */ + put_unaligned_le32(baud, buf); + + err = mxuport_send_ctrl_data_urb(serial, RQ_VENDOR_SET_BAUD, + 0, port->port_number, + buf, 4); + if (err) + goto out; + + dev_dbg(&port->dev, "baud_rate : %d\n", baud); + dev_dbg(&port->dev, "data_bits : %d\n", data_bits); + dev_dbg(&port->dev, "parity : %d\n", parity); + dev_dbg(&port->dev, "stop_bits : %d\n", stop_bits); + +out: + kfree(buf); +} + +/* + * Determine how many ports this device has dynamically. It will be + * called after the probe() callback is called, but before attach(). + */ +static int mxuport_calc_num_ports(struct usb_serial *serial) +{ + unsigned long features = (unsigned long)usb_get_serial_data(serial); + + if (features & MX_UPORT_2_PORT) + return 2; + if (features & MX_UPORT_4_PORT) + return 4; + if (features & MX_UPORT_8_PORT) + return 8; + if (features & MX_UPORT_16_PORT) + return 16; + + return 0; +} + +/* Get the version of the firmware currently running. */ +static int mxuport_get_fw_version(struct usb_serial *serial, u32 *version) +{ + u8 *ver_buf; + int err; + + ver_buf = kzalloc(4, GFP_KERNEL); + if (!ver_buf) + return -ENOMEM; + + /* Get firmware version from SDRAM */ + err = mxuport_recv_ctrl_urb(serial, RQ_VENDOR_GET_VERSION, 0, 0, + ver_buf, 4); + if (err != 4) { + err = -EIO; + goto out; + } + + *version = (ver_buf[0] << 16) | (ver_buf[1] << 8) | ver_buf[2]; + err = 0; +out: + kfree(ver_buf); + return err; +} + +/* Given a firmware blob, download it to the device. */ +static int mxuport_download_fw(struct usb_serial *serial, + const struct firmware *fw_p) +{ + u8 *fw_buf; + size_t txlen; + size_t fwidx; + int err; + + fw_buf = kmalloc(DOWN_BLOCK_SIZE, GFP_KERNEL); + if (!fw_buf) + return -ENOMEM; + + dev_dbg(&serial->interface->dev, "Starting firmware download...\n"); + err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_START_FW_DOWN, 0, 0); + if (err) + goto out; + + fwidx = 0; + do { + txlen = min_t(size_t, (fw_p->size - fwidx), DOWN_BLOCK_SIZE); + + memcpy(fw_buf, &fw_p->data[fwidx], txlen); + err = mxuport_send_ctrl_data_urb(serial, RQ_VENDOR_FW_DATA, + 0, 0, fw_buf, txlen); + if (err) { + mxuport_send_ctrl_urb(serial, RQ_VENDOR_STOP_FW_DOWN, + 0, 0); + goto out; + } + + fwidx += txlen; + usleep_range(1000, 2000); + + } while (fwidx < fw_p->size); + + msleep(1000); + err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_STOP_FW_DOWN, 0, 0); + if (err) + goto out; + + msleep(1000); + err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_QUERY_FW_READY, 0, 0); + +out: + kfree(fw_buf); + return err; +} + +static int mxuport_probe(struct usb_serial *serial, + const struct usb_device_id *id) +{ + u16 productid = le16_to_cpu(serial->dev->descriptor.idProduct); + const struct firmware *fw_p = NULL; + u32 version; + int local_ver; + char buf[32]; + int err; + + /* Load our firmware */ + err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_QUERY_FW_CONFIG, 0, 0); + if (err) { + mxuport_send_ctrl_urb(serial, RQ_VENDOR_RESET_DEVICE, 0, 0); + return err; + } + + err = mxuport_get_fw_version(serial, &version); + if (err < 0) + return err; + + dev_dbg(&serial->interface->dev, "Device firmware version v%x.%x.%x\n", + (version & 0xff0000) >> 16, + (version & 0xff00) >> 8, + (version & 0xff)); + + snprintf(buf, sizeof(buf) - 1, "moxa/moxa-%04x.fw", productid); + + err = request_firmware(&fw_p, buf, &serial->interface->dev); + if (err) { + dev_warn(&serial->interface->dev, "Firmware %s not found\n", + buf); + + /* Use the firmware already in the device */ + err = 0; + } else { + local_ver = ((fw_p->data[VER_ADDR_1] << 16) | + (fw_p->data[VER_ADDR_2] << 8) | + fw_p->data[VER_ADDR_3]); + dev_dbg(&serial->interface->dev, + "Available firmware version v%x.%x.%x\n", + fw_p->data[VER_ADDR_1], fw_p->data[VER_ADDR_2], + fw_p->data[VER_ADDR_3]); + if (local_ver > version) { + err = mxuport_download_fw(serial, fw_p); + if (err) + goto out; + err = mxuport_get_fw_version(serial, &version); + if (err < 0) + goto out; + } + } + + dev_info(&serial->interface->dev, + "Using device firmware version v%x.%x.%x\n", + (version & 0xff0000) >> 16, + (version & 0xff00) >> 8, + (version & 0xff)); + + /* + * Contains the features of this hardware. Store away for + * later use, eg, number of ports. + */ + usb_set_serial_data(serial, (void *)id->driver_info); +out: + if (fw_p) + release_firmware(fw_p); + return err; +} + + +static int mxuport_port_probe(struct usb_serial_port *port) +{ + struct usb_serial *serial = port->serial; + struct mxuport_port *mxport; + int err; + + mxport = devm_kzalloc(&port->dev, sizeof(struct mxuport_port), + GFP_KERNEL); + if (!mxport) + return -ENOMEM; + + mutex_init(&mxport->mutex); + spin_lock_init(&mxport->spinlock); + + /* Set the port private data */ + usb_set_serial_port_data(port, mxport); + + /* Set FIFO (Enable) */ + err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_FIFO_DISABLE, + 0, port->port_number); + if (err) + return err; + + /* Set transmission mode (Hi-Performance) */ + err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_HIGH_PERFOR, + 0, port->port_number); + if (err) + return err; + + /* Set interface (RS-232) */ + err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_INTERFACE, + MX_INT_RS232, + port->port_number); + if (err) + return err; + + return 0; +} + +static int mxuport_alloc_write_urb(struct usb_serial *serial, + struct usb_serial_port *port, + struct usb_serial_port *port0, + int j) +{ + struct usb_device *dev = interface_to_usbdev(serial->interface); + + set_bit(j, &port->write_urbs_free); + port->write_urbs[j] = usb_alloc_urb(0, GFP_KERNEL); + if (!port->write_urbs[j]) + return -ENOMEM; + + port->bulk_out_buffers[j] = kmalloc(port0->bulk_out_size, GFP_KERNEL); + if (!port->bulk_out_buffers[j]) + return -ENOMEM; + + usb_fill_bulk_urb(port->write_urbs[j], dev, + usb_sndbulkpipe(dev, port->bulk_out_endpointAddress), + port->bulk_out_buffers[j], + port->bulk_out_size, + serial->type->write_bulk_callback, + port); + return 0; +} + + +static int mxuport_alloc_write_urbs(struct usb_serial *serial, + struct usb_serial_port *port, + struct usb_serial_port *port0) +{ + int j; + int ret; + + for (j = 0; j < ARRAY_SIZE(port->write_urbs); ++j) { + ret = mxuport_alloc_write_urb(serial, port, port0, j); + if (ret) + return ret; + } + return 0; +} + + +static int mxuport_attach(struct usb_serial *serial) +{ + struct usb_serial_port *port0 = serial->port[0]; + struct usb_serial_port *port1 = serial->port[1]; + struct usb_serial_port *port; + int err; + int i; + int j; + + /* + * Throw away all but the first allocated write URBs so we can + * set them up again to fit the multiplexing scheme. + */ + for (i = 1; i < serial->num_bulk_out; ++i) { + port = serial->port[i]; + for (j = 0; j < ARRAY_SIZE(port->write_urbs); ++j) { + usb_free_urb(port->write_urbs[j]); + kfree(port->bulk_out_buffers[j]); + port->write_urbs[j] = NULL; + port->bulk_out_buffers[j] = NULL; + } + port->write_urbs_free = 0; + } + + /* + * All write data is sent over the first bulk out endpoint, + * with an added header to indicate the port. Allocate URBs + * for each port to the first bulk out endpoint. + */ + for (i = 1; i < serial->num_ports; ++i) { + port = serial->port[i]; + port->bulk_out_size = port0->bulk_out_size; + port->bulk_out_endpointAddress = + port0->bulk_out_endpointAddress; + + err = mxuport_alloc_write_urbs(serial, port, port0); + if (err) + return err; + + port->write_urb = port->write_urbs[0]; + port->bulk_out_buffer = port->bulk_out_buffers[0]; + + /* + * Ensure each port has a fifo. The framework only + * allocates a fifo to ports with a bulk out endpoint, + * where as we need one for every port. + */ + if (!kfifo_initialized(&port->write_fifo)) { + err = kfifo_alloc(&port->write_fifo, PAGE_SIZE, + GFP_KERNEL); + if (err) + return err; + } + } + + /* + * All data from the ports is received on the first bulk in + * endpoint, with a multiplex header. The second bulk in is + * used for events. + * + * Start to read from the device. + */ + err = usb_serial_generic_submit_read_urbs(port0, GFP_KERNEL); + if (err) + return err; + + err = usb_serial_generic_submit_read_urbs(port1, GFP_KERNEL); + if (err) { + usb_serial_generic_close(port0); + return err; + } + + return 0; +} + +static int mxuport_open(struct tty_struct *tty, struct usb_serial_port *port) +{ + struct mxuport_port *mxport = usb_get_serial_port_data(port); + struct usb_serial *serial = port->serial; + int err; + + /* Set receive host (enable) */ + err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_RX_HOST_EN, + 1, port->port_number); + if (err) + return err; + + err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_OPEN, + 1, port->port_number); + if (err) { + mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_RX_HOST_EN, + 0, port->port_number); + return err; + } + + /* Initial port termios */ + mxuport_set_termios(tty, port, NULL); + + /* + * TODO: use RQ_VENDOR_GET_MSR, once we know what it + * returns. + */ + mxport->msr_state = 0; + + return err; +} + +static void mxuport_close(struct usb_serial_port *port) +{ + struct usb_serial *serial = port->serial; + + mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_OPEN, 0, + port->port_number); + + mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_RX_HOST_EN, 0, + port->port_number); +} + +/* Send a break to the port. */ +static void mxuport_break_ctl(struct tty_struct *tty, int break_state) +{ + struct usb_serial_port *port = tty->driver_data; + struct usb_serial *serial = port->serial; + int enable; + + if (break_state == -1) { + enable = 1; + dev_dbg(&port->dev, "%s - sending break\n", __func__); + } else { + enable = 0; + dev_dbg(&port->dev, "%s - clearing break\n", __func__); + } + + mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_BREAK, + enable, port->port_number); +} + +static int mxuport_resume(struct usb_serial *serial) +{ + struct usb_serial_port *port; + int c = 0; + int i; + int r; + + for (i = 0; i < 2; i++) { + port = serial->port[i]; + + r = usb_serial_generic_submit_read_urbs(port, GFP_NOIO); + if (r < 0) + c++; + } + + for (i = 0; i < serial->num_ports; i++) { + port = serial->port[i]; + if (!test_bit(ASYNCB_INITIALIZED, &port->port.flags)) + continue; + + r = usb_serial_generic_write_start(port, GFP_NOIO); + if (r < 0) + c++; + } + + return c ? -EIO : 0; +} + +static struct usb_serial_driver mxuport_device = { + .driver = { + .owner = THIS_MODULE, + .name = "mxuport", + }, + .description = "MOXA UPort", + .id_table = mxuport_idtable, + .num_ports = 0, + .probe = mxuport_probe, + .port_probe = mxuport_port_probe, + .attach = mxuport_attach, + .calc_num_ports = mxuport_calc_num_ports, + .open = mxuport_open, + .close = mxuport_close, + .set_termios = mxuport_set_termios, + .break_ctl = mxuport_break_ctl, + .tx_empty = mxuport_tx_empty, + .tiocmiwait = usb_serial_generic_tiocmiwait, + .get_icount = usb_serial_generic_get_icount, + .throttle = mxuport_throttle, + .unthrottle = mxuport_unthrottle, + .tiocmget = mxuport_tiocmget, + .tiocmset = mxuport_tiocmset, + .dtr_rts = mxuport_dtr_rts, + .process_read_urb = mxuport_process_read_urb, + .prepare_write_buffer = mxuport_prepare_write_buffer, + .resume = mxuport_resume, +}; + +static struct usb_serial_driver *const serial_drivers[] = { + &mxuport_device, NULL +}; + +module_usb_serial_driver(serial_drivers, mxuport_idtable); + +MODULE_AUTHOR("Andrew Lunn <andrew@lunn.ch>"); +MODULE_AUTHOR("<support@moxa.com>"); +MODULE_LICENSE("GPL"); diff --git a/drivers/usb/serial/navman.c b/drivers/usb/serial/navman.c index 1566f8f500a..2a97cdc078d 100644 --- a/drivers/usb/serial/navman.c +++ b/drivers/usb/serial/navman.c @@ -14,7 +14,6 @@ #include <linux/gfp.h> #include <linux/kernel.h> -#include <linux/init.h> #include <linux/tty.h> #include <linux/tty_flip.h> #include <linux/module.h> @@ -32,7 +31,6 @@ static void navman_read_int_callback(struct urb *urb) { struct usb_serial_port *port = urb->context; unsigned char *data = urb->transfer_buffer; - struct tty_struct *tty; int status = urb->status; int result; @@ -55,12 +53,10 @@ static void navman_read_int_callback(struct urb *urb) usb_serial_debug_data(&port->dev, __func__, urb->actual_length, data); - tty = tty_port_tty_get(&port->port); - if (tty && urb->actual_length) { - tty_insert_flip_string(tty, data, urb->actual_length); - tty_flip_buffer_push(tty); + if (urb->actual_length) { + tty_insert_flip_string(&port->port, data, urb->actual_length); + tty_flip_buffer_push(&port->port); } - tty_kref_put(tty); exit: result = usb_submit_urb(urb, GFP_ATOMIC); diff --git a/drivers/usb/serial/omninet.c b/drivers/usb/serial/omninet.c index 7818af931a4..f6c6900bccf 100644 --- a/drivers/usb/serial/omninet.c +++ b/drivers/usb/serial/omninet.c @@ -13,7 +13,6 @@ #include <linux/kernel.h> #include <linux/errno.h> -#include <linux/init.h> #include <linux/slab.h> #include <linux/tty.h> #include <linux/tty_driver.h> @@ -33,8 +32,7 @@ /* function prototypes */ static int omninet_open(struct tty_struct *tty, struct usb_serial_port *port); -static void omninet_close(struct usb_serial_port *port); -static void omninet_read_bulk_callback(struct urb *urb); +static void omninet_process_read_urb(struct urb *urb); static void omninet_write_bulk_callback(struct urb *urb); static int omninet_write(struct tty_struct *tty, struct usb_serial_port *port, const unsigned char *buf, int count); @@ -61,11 +59,10 @@ static struct usb_serial_driver zyxel_omninet_device = { .port_probe = omninet_port_probe, .port_remove = omninet_port_remove, .open = omninet_open, - .close = omninet_close, .write = omninet_write, .write_room = omninet_write_room, - .read_bulk_callback = omninet_read_bulk_callback, .write_bulk_callback = omninet_write_bulk_callback, + .process_read_urb = omninet_process_read_urb, .disconnect = omninet_disconnect, }; @@ -74,29 +71,28 @@ static struct usb_serial_driver * const serial_drivers[] = { }; -/* The protocol. +/* + * The protocol. * * The omni.net always exchange 64 bytes of data with the host. The first - * four bytes are the control header, you can see it in the above structure. + * four bytes are the control header. * * oh_seq is a sequence number. Don't know if/how it's used. * oh_len is the length of the data bytes in the packet. * oh_xxx Bit-mapped, related to handshaking and status info. - * I normally set it to 0x03 in trasmitted frames. + * I normally set it to 0x03 in transmitted frames. * 7: Active when the TA is in a CONNECTed state. * 6: unknown * 5: handshaking, unknown * 4: handshaking, unknown * 3: unknown, usually 0 * 2: unknown, usually 0 - * 1: handshaking, unknown, usually set to 1 in trasmitted frames - * 0: handshaking, unknown, usually set to 1 in trasmitted frames + * 1: handshaking, unknown, usually set to 1 in transmitted frames + * 0: handshaking, unknown, usually set to 1 in transmitted frames * oh_pad Probably a pad byte. * * After the header you will find data bytes if oh_len was greater than zero. - * */ - struct omninet_header { __u8 oh_seq; __u8 oh_len; @@ -112,7 +108,7 @@ static int omninet_port_probe(struct usb_serial_port *port) { struct omninet_data *od; - od = kmalloc(sizeof(struct omninet_data), GFP_KERNEL); + od = kzalloc(sizeof(*od), GFP_KERNEL); if (!od) return -ENOMEM; @@ -135,60 +131,32 @@ static int omninet_open(struct tty_struct *tty, struct usb_serial_port *port) { struct usb_serial *serial = port->serial; struct usb_serial_port *wport; - int result = 0; wport = serial->port[1]; tty_port_tty_set(&wport->port, tty); - /* Start reading from the device */ - result = usb_submit_urb(port->read_urb, GFP_KERNEL); - if (result) - dev_err(&port->dev, - "%s - failed submitting read urb, error %d\n", - __func__, result); - return result; -} - -static void omninet_close(struct usb_serial_port *port) -{ - usb_kill_urb(port->read_urb); + return usb_serial_generic_open(tty, port); } +#define OMNINET_HEADERLEN 4 +#define OMNINET_BULKOUTSIZE 64 +#define OMNINET_PAYLOADSIZE (OMNINET_BULKOUTSIZE - OMNINET_HEADERLEN) -#define OMNINET_DATAOFFSET 0x04 -#define OMNINET_HEADERLEN sizeof(struct omninet_header) -#define OMNINET_BULKOUTSIZE (64 - OMNINET_HEADERLEN) - -static void omninet_read_bulk_callback(struct urb *urb) +static void omninet_process_read_urb(struct urb *urb) { - struct usb_serial_port *port = urb->context; - unsigned char *data = urb->transfer_buffer; - struct omninet_header *header = (struct omninet_header *) &data[0]; - int status = urb->status; - int result; + struct usb_serial_port *port = urb->context; + const struct omninet_header *hdr = urb->transfer_buffer; + const unsigned char *data; + size_t data_len; - if (status) { - dev_dbg(&port->dev, "%s - nonzero read bulk status received: %d\n", - __func__, status); + if (urb->actual_length <= OMNINET_HEADERLEN || !hdr->oh_len) return; - } - - if (urb->actual_length && header->oh_len) { - struct tty_struct *tty = tty_port_tty_get(&port->port); - if (tty) { - tty_insert_flip_string(tty, data + OMNINET_DATAOFFSET, - header->oh_len); - tty_flip_buffer_push(tty); - tty_kref_put(tty); - } - } - /* Continue trying to always read */ - result = usb_submit_urb(urb, GFP_ATOMIC); - if (result) - dev_err(&port->dev, - "%s - failed resubmitting read urb, error %d\n", - __func__, result); + data = (char *)urb->transfer_buffer + OMNINET_HEADERLEN; + data_len = min_t(size_t, urb->actual_length - OMNINET_HEADERLEN, + hdr->oh_len); + tty_insert_flip_string(&port->port, data, data_len); + tty_flip_buffer_push(&port->port); } static int omninet_write(struct tty_struct *tty, struct usb_serial_port *port, @@ -213,9 +181,9 @@ static int omninet_write(struct tty_struct *tty, struct usb_serial_port *port, return 0; } - count = (count > OMNINET_BULKOUTSIZE) ? OMNINET_BULKOUTSIZE : count; + count = (count > OMNINET_PAYLOADSIZE) ? OMNINET_PAYLOADSIZE : count; - memcpy(wport->write_urb->transfer_buffer + OMNINET_DATAOFFSET, + memcpy(wport->write_urb->transfer_buffer + OMNINET_HEADERLEN, buf, count); usb_serial_debug_data(&port->dev, __func__, count, @@ -227,7 +195,7 @@ static int omninet_write(struct tty_struct *tty, struct usb_serial_port *port, header->oh_pad = 0x00; /* send the data out the bulk port, always 64 bytes */ - wport->write_urb->transfer_buffer_length = 64; + wport->write_urb->transfer_buffer_length = OMNINET_BULKOUTSIZE; result = usb_submit_urb(wport->write_urb, GFP_ATOMIC); if (result) { diff --git a/drivers/usb/serial/opticon.c b/drivers/usb/serial/opticon.c index c6bfb83efb1..4856fb7e637 100644 --- a/drivers/usb/serial/opticon.c +++ b/drivers/usb/serial/opticon.c @@ -12,7 +12,6 @@ */ #include <linux/kernel.h> -#include <linux/init.h> #include <linux/tty.h> #include <linux/tty_driver.h> #include <linux/slab.h> @@ -51,15 +50,8 @@ struct opticon_private { static void opticon_process_data_packet(struct usb_serial_port *port, const unsigned char *buf, size_t len) { - struct tty_struct *tty; - - tty = tty_port_tty_get(&port->port); - if (!tty) - return; - - tty_insert_flip_string(tty, buf, len); - tty_flip_buffer_push(tty); - tty_kref_put(tty); + tty_insert_flip_string(&port->port, buf, len); + tty_flip_buffer_push(&port->port); } static void opticon_process_status_packet(struct usb_serial_port *port, @@ -127,7 +119,10 @@ static int send_control_msg(struct usb_serial_port *port, u8 requesttype, 0, 0, buffer, 1, 0); kfree(buffer); - return retval; + if (retval < 0) + return retval; + + return 0; } static int opticon_open(struct tty_struct *tty, struct usb_serial_port *port) @@ -143,7 +138,7 @@ static int opticon_open(struct tty_struct *tty, struct usb_serial_port *port) /* Clear RTS line */ send_control_msg(port, CONTROL_RTS, 0); - /* clear the halt status of the enpoint */ + /* clear the halt status of the endpoint */ usb_clear_halt(port->serial->dev, port->read_urb->pipe); res = usb_serial_generic_open(tty, port); @@ -204,15 +199,12 @@ static int opticon_write(struct tty_struct *tty, struct usb_serial_port *port, buffer = kmalloc(count, GFP_ATOMIC); if (!buffer) { - dev_err(&port->dev, "out of memory\n"); count = -ENOMEM; - goto error_no_buffer; } urb = usb_alloc_urb(0, GFP_ATOMIC); if (!urb) { - dev_err(&port->dev, "no more free urbs\n"); count = -ENOMEM; goto error_no_urb; } @@ -221,11 +213,10 @@ static int opticon_write(struct tty_struct *tty, struct usb_serial_port *port, usb_serial_debug_data(&port->dev, __func__, count, buffer); - /* The conncected devices do not have a bulk write endpoint, + /* The connected devices do not have a bulk write endpoint, * to transmit data to de barcode device the control endpoint is used */ dr = kmalloc(sizeof(struct usb_ctrlrequest), GFP_NOIO); if (!dr) { - dev_err(&port->dev, "out of memory\n"); count = -ENOMEM; goto error_no_dr; } @@ -313,7 +304,6 @@ static int opticon_tiocmset(struct tty_struct *tty, unsigned int set, unsigned int clear) { struct usb_serial_port *port = tty->driver_data; - struct usb_serial *serial = port->serial; struct opticon_private *priv = usb_get_serial_port_data(port); unsigned long flags; bool rts; @@ -334,15 +324,11 @@ static int opticon_tiocmset(struct tty_struct *tty, if (!changed) return 0; - /* Send the new RTS state to the connected device */ - mutex_lock(&serial->disc_mutex); - if (!serial->disconnected) - ret = send_control_msg(port, CONTROL_RTS, !rts); - else - ret = -ENODEV; - mutex_unlock(&serial->disc_mutex); + ret = send_control_msg(port, CONTROL_RTS, !rts); + if (ret) + return usb_translate_errors(ret); - return ret; + return 0; } static int get_serial_info(struct usb_serial_port *port, @@ -357,7 +343,7 @@ static int get_serial_info(struct usb_serial_port *port, /* fake emulate a 16550 uart to make userspace code happy */ tmp.type = PORT_16550A; - tmp.line = port->serial->minor; + tmp.line = port->minor; tmp.port = 0; tmp.irq = 0; tmp.flags = ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ; @@ -376,8 +362,6 @@ static int opticon_ioctl(struct tty_struct *tty, { struct usb_serial_port *port = tty->driver_data; - dev_dbg(&port->dev, "%s - port %d, cmd = 0x%x\n", __func__, port->number, cmd); - switch (cmd) { case TIOCGSERIAL: return get_serial_info(port, diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index 0d9dac9e7f9..a9688940543 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -81,9 +81,11 @@ static void option_instat_callback(struct urb *urb); #define HUAWEI_VENDOR_ID 0x12D1 #define HUAWEI_PRODUCT_E173 0x140C +#define HUAWEI_PRODUCT_E1750 0x1406 #define HUAWEI_PRODUCT_K4505 0x1464 #define HUAWEI_PRODUCT_K3765 0x1465 #define HUAWEI_PRODUCT_K4605 0x14C6 +#define HUAWEI_PRODUCT_E173S6 0x1C07 #define QUANTA_VENDOR_ID 0x0408 #define QUANTA_PRODUCT_Q101 0xEA02 @@ -159,8 +161,7 @@ static void option_instat_callback(struct urb *urb); #define NOVATELWIRELESS_PRODUCT_HSPA_EMBEDDED_FULLSPEED 0x9000 #define NOVATELWIRELESS_PRODUCT_HSPA_EMBEDDED_HIGHSPEED 0x9001 #define NOVATELWIRELESS_PRODUCT_E362 0x9010 -#define NOVATELWIRELESS_PRODUCT_G1 0xA001 -#define NOVATELWIRELESS_PRODUCT_G1_M 0xA002 +#define NOVATELWIRELESS_PRODUCT_E371 0x9011 #define NOVATELWIRELESS_PRODUCT_G2 0xA010 #define NOVATELWIRELESS_PRODUCT_MC551 0xB001 @@ -196,6 +197,7 @@ static void option_instat_callback(struct urb *urb); #define DELL_PRODUCT_5800_MINICARD_VZW 0x8195 /* Novatel E362 */ #define DELL_PRODUCT_5800_V2_MINICARD_VZW 0x8196 /* Novatel E362 */ +#define DELL_PRODUCT_5804_MINICARD_ATT 0x819b /* Novatel E371 */ #define KYOCERA_VENDOR_ID 0x0c88 #define KYOCERA_PRODUCT_KPC650 0x17da @@ -233,8 +235,31 @@ static void option_instat_callback(struct urb *urb); #define QUALCOMM_VENDOR_ID 0x05C6 #define CMOTECH_VENDOR_ID 0x16d8 -#define CMOTECH_PRODUCT_6008 0x6008 -#define CMOTECH_PRODUCT_6280 0x6280 +#define CMOTECH_PRODUCT_6001 0x6001 +#define CMOTECH_PRODUCT_CMU_300 0x6002 +#define CMOTECH_PRODUCT_6003 0x6003 +#define CMOTECH_PRODUCT_6004 0x6004 +#define CMOTECH_PRODUCT_6005 0x6005 +#define CMOTECH_PRODUCT_CGU_628A 0x6006 +#define CMOTECH_PRODUCT_CHE_628S 0x6007 +#define CMOTECH_PRODUCT_CMU_301 0x6008 +#define CMOTECH_PRODUCT_CHU_628 0x6280 +#define CMOTECH_PRODUCT_CHU_628S 0x6281 +#define CMOTECH_PRODUCT_CDU_680 0x6803 +#define CMOTECH_PRODUCT_CDU_685A 0x6804 +#define CMOTECH_PRODUCT_CHU_720S 0x7001 +#define CMOTECH_PRODUCT_7002 0x7002 +#define CMOTECH_PRODUCT_CHU_629K 0x7003 +#define CMOTECH_PRODUCT_7004 0x7004 +#define CMOTECH_PRODUCT_7005 0x7005 +#define CMOTECH_PRODUCT_CGU_629 0x7006 +#define CMOTECH_PRODUCT_CHU_629S 0x700a +#define CMOTECH_PRODUCT_CHU_720I 0x7211 +#define CMOTECH_PRODUCT_7212 0x7212 +#define CMOTECH_PRODUCT_7213 0x7213 +#define CMOTECH_PRODUCT_7251 0x7251 +#define CMOTECH_PRODUCT_7252 0x7252 +#define CMOTECH_PRODUCT_7253 0x7253 #define TELIT_VENDOR_ID 0x1bc7 #define TELIT_PRODUCT_UC864E 0x1003 @@ -242,19 +267,16 @@ static void option_instat_callback(struct urb *urb); #define TELIT_PRODUCT_CC864_DUAL 0x1005 #define TELIT_PRODUCT_CC864_SINGLE 0x1006 #define TELIT_PRODUCT_DE910_DUAL 0x1010 +#define TELIT_PRODUCT_UE910_V2 0x1012 +#define TELIT_PRODUCT_LE920 0x1200 /* ZTE PRODUCTS */ #define ZTE_VENDOR_ID 0x19d2 #define ZTE_PRODUCT_MF622 0x0001 #define ZTE_PRODUCT_MF628 0x0015 #define ZTE_PRODUCT_MF626 0x0031 -#define ZTE_PRODUCT_CDMA_TECH 0xfffe -#define ZTE_PRODUCT_AC8710 0xfff1 -#define ZTE_PRODUCT_AC2726 0xfff5 -#define ZTE_PRODUCT_AC8710T 0xffff #define ZTE_PRODUCT_MC2718 0xffe8 -#define ZTE_PRODUCT_AD3812 0xffeb -#define ZTE_PRODUCT_MC2716 0xffed +#define ZTE_PRODUCT_AC2726 0xfff1 #define BENQ_VENDOR_ID 0x04a5 #define BENQ_PRODUCT_H10 0x4068 @@ -289,6 +311,7 @@ static void option_instat_callback(struct urb *urb); #define ALCATEL_PRODUCT_X060S_X200 0x0000 #define ALCATEL_PRODUCT_X220_X500D 0x0017 #define ALCATEL_PRODUCT_L100V 0x011e +#define ALCATEL_PRODUCT_L800MA 0x0203 #define PIRELLI_VENDOR_ID 0x1266 #define PIRELLI_PRODUCT_C100_1 0x1002 @@ -323,9 +346,15 @@ static void option_instat_callback(struct urb *urb); * It seems to contain a Qualcomm QSC6240/6290 chipset */ #define FOUR_G_SYSTEMS_PRODUCT_W14 0x9603 +/* iBall 3.5G connect wireless modem */ +#define IBALL_3_5G_CONNECT 0x9605 + /* Zoom */ #define ZOOM_PRODUCT_4597 0x9607 +/* SpeedUp SU9800 usb 3g modem */ +#define SPEEDUP_PRODUCT_SU9800 0x9800 + /* Haier products */ #define HAIER_VENDOR_ID 0x201e #define HAIER_PRODUCT_CE100 0x2009 @@ -340,21 +369,24 @@ static void option_instat_callback(struct urb *urb); #define CINTERION_PRODUCT_EU3_E 0x0051 #define CINTERION_PRODUCT_EU3_P 0x0052 #define CINTERION_PRODUCT_PH8 0x0053 +#define CINTERION_PRODUCT_AHXX 0x0055 +#define CINTERION_PRODUCT_PLXX 0x0060 /* Olivetti products */ #define OLIVETTI_VENDOR_ID 0x0b3c #define OLIVETTI_PRODUCT_OLICARD100 0xc000 +#define OLIVETTI_PRODUCT_OLICARD120 0xc001 +#define OLIVETTI_PRODUCT_OLICARD140 0xc002 +#define OLIVETTI_PRODUCT_OLICARD145 0xc003 +#define OLIVETTI_PRODUCT_OLICARD155 0xc004 +#define OLIVETTI_PRODUCT_OLICARD200 0xc005 +#define OLIVETTI_PRODUCT_OLICARD160 0xc00a +#define OLIVETTI_PRODUCT_OLICARD500 0xc00b /* Celot products */ #define CELOT_VENDOR_ID 0x211f #define CELOT_PRODUCT_CT680M 0x6801 -/* ONDA Communication vendor id */ -#define ONDA_VENDOR_ID 0x1ee8 - -/* ONDA MT825UP HSDPA 14.2 modem */ -#define ONDA_MT825UP 0x000b - /* Samsung products */ #define SAMSUNG_VENDOR_ID 0x04e8 #define SAMSUNG_PRODUCT_GT_B3730 0x6889 @@ -447,12 +479,21 @@ static void option_instat_callback(struct urb *urb); /* Hyundai Petatel Inc. products */ #define PETATEL_VENDOR_ID 0x1ff4 -#define PETATEL_PRODUCT_NP10T 0x600e +#define PETATEL_PRODUCT_NP10T_600A 0x600a +#define PETATEL_PRODUCT_NP10T_600E 0x600e /* TP-LINK Incorporated products */ #define TPLINK_VENDOR_ID 0x2357 #define TPLINK_PRODUCT_MA180 0x0201 +/* Changhong products */ +#define CHANGHONG_VENDOR_ID 0x2077 +#define CHANGHONG_PRODUCT_CH690 0x7001 + +/* Inovia */ +#define INOVIA_VENDOR_ID 0x20a6 +#define INOVIA_SEW858 0x1105 + /* some devices interfaces need special handling due to a number of reasons */ enum option_blacklist_reason { OPTION_BLACKLIST_NONE = 0, @@ -474,6 +515,7 @@ static const struct option_blacklist_info four_g_w14_blacklist = { static const struct option_blacklist_info alcatel_x200_blacklist = { .sendsetup = BIT(0) | BIT(1), + .reserved = BIT(4), }; static const struct option_blacklist_info zte_0037_blacklist = { @@ -485,22 +527,18 @@ static const struct option_blacklist_info zte_k3765_z_blacklist = { .reserved = BIT(4), }; -static const struct option_blacklist_info zte_ad3812_z_blacklist = { - .sendsetup = BIT(0) | BIT(1) | BIT(2), -}; - static const struct option_blacklist_info zte_mc2718_z_blacklist = { .sendsetup = BIT(1) | BIT(2) | BIT(3) | BIT(4), }; -static const struct option_blacklist_info zte_mc2716_z_blacklist = { - .sendsetup = BIT(1) | BIT(2) | BIT(3), -}; - static const struct option_blacklist_info huawei_cdc12_blacklist = { .reserved = BIT(1) | BIT(2), }; +static const struct option_blacklist_info net_intf0_blacklist = { + .reserved = BIT(0), +}; + static const struct option_blacklist_info net_intf1_blacklist = { .reserved = BIT(1), }; @@ -534,6 +572,11 @@ static const struct option_blacklist_info zte_1255_blacklist = { .reserved = BIT(3) | BIT(4), }; +static const struct option_blacklist_info telit_le920_blacklist = { + .sendsetup = BIT(0), + .reserved = BIT(1) | BIT(5), +}; + static const struct usb_device_id option_ids[] = { { USB_DEVICE(OPTION_VENDOR_ID, OPTION_PRODUCT_COLT) }, { USB_DEVICE(OPTION_VENDOR_ID, OPTION_PRODUCT_RICOLA) }, @@ -565,12 +608,25 @@ static const struct usb_device_id option_ids[] = { { USB_DEVICE(QUANTA_VENDOR_ID, QUANTA_PRODUCT_GLX) }, { USB_DEVICE(QUANTA_VENDOR_ID, QUANTA_PRODUCT_GKE) }, { USB_DEVICE(QUANTA_VENDOR_ID, QUANTA_PRODUCT_GLE) }, + { USB_DEVICE(QUANTA_VENDOR_ID, 0xea42), + .driver_info = (kernel_ulong_t)&net_intf4_blacklist }, + { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0x1c05, USB_CLASS_COMM, 0x02, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0x1c1f, USB_CLASS_COMM, 0x02, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0x1c23, USB_CLASS_COMM, 0x02, 0xff) }, { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_E173, 0xff, 0xff, 0xff), .driver_info = (kernel_ulong_t) &net_intf1_blacklist }, + { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_E173S6, 0xff, 0xff, 0xff), + .driver_info = (kernel_ulong_t) &net_intf1_blacklist }, + { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_E1750, 0xff, 0xff, 0xff), + .driver_info = (kernel_ulong_t) &net_intf2_blacklist }, + { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0x1441, USB_CLASS_COMM, 0x02, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0x1442, USB_CLASS_COMM, 0x02, 0xff) }, { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_K4505, 0xff, 0xff, 0xff), .driver_info = (kernel_ulong_t) &huawei_cdc12_blacklist }, { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_K3765, 0xff, 0xff, 0xff), .driver_info = (kernel_ulong_t) &huawei_cdc12_blacklist }, + { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0x14ac, 0xff, 0xff, 0xff), /* Huawei E1820 */ + .driver_info = (kernel_ulong_t) &net_intf1_blacklist }, { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_K4605, 0xff, 0xff, 0xff), .driver_info = (kernel_ulong_t) &huawei_cdc12_blacklist }, { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0xff, 0xff) }, @@ -623,6 +679,10 @@ static const struct usb_device_id option_ids[] = { { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x01, 0x6D) }, { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x01, 0x6E) }, { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x01, 0x6F) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x01, 0x72) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x01, 0x73) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x01, 0x74) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x01, 0x75) }, { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x01, 0x78) }, { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x01, 0x79) }, { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x01, 0x7A) }, @@ -677,11 +737,247 @@ static const struct usb_device_id option_ids[] = { { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x02, 0x6D) }, { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x02, 0x6E) }, { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x02, 0x6F) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x02, 0x72) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x02, 0x73) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x02, 0x74) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x02, 0x75) }, { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x02, 0x78) }, { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x02, 0x79) }, { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x02, 0x7A) }, { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x02, 0x7B) }, { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x02, 0x7C) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x01) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x02) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x03) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x04) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x05) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x06) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x0A) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x0B) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x0D) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x0E) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x0F) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x10) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x12) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x13) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x14) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x15) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x17) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x18) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x19) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x1A) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x1B) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x1C) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x31) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x32) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x33) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x34) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x35) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x36) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x3A) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x3B) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x3D) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x3E) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x3F) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x48) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x49) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x4A) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x4B) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x4C) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x61) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x62) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x63) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x64) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x65) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x66) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x6A) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x6B) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x6D) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x6E) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x6F) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x72) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x73) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x74) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x75) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x78) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x79) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x7A) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x7B) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x03, 0x7C) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x01) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x02) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x03) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x04) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x05) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x06) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x0A) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x0B) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x0D) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x0E) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x0F) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x10) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x12) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x13) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x14) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x15) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x17) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x18) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x19) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x1A) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x1B) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x1C) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x31) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x32) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x33) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x34) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x35) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x36) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x3A) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x3B) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x3D) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x3E) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x3F) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x48) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x49) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x4A) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x4B) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x4C) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x61) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x62) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x63) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x64) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x65) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x66) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x6A) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x6B) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x6D) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x6E) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x6F) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x72) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x73) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x74) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x75) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x78) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x79) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x7A) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x7B) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x04, 0x7C) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x01) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x02) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x03) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x04) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x05) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x06) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x0A) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x0B) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x0D) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x0E) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x0F) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x10) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x12) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x13) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x14) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x15) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x17) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x18) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x19) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x1A) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x1B) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x1C) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x31) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x32) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x33) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x34) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x35) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x36) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x3A) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x3B) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x3D) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x3E) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x3F) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x48) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x49) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x4A) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x4B) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x4C) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x61) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x62) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x63) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x64) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x65) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x66) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x6A) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x6B) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x6D) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x6E) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x6F) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x72) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x73) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x74) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x75) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x78) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x79) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x7A) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x7B) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x05, 0x7C) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x01) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x02) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x03) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x04) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x05) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x06) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x0A) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x0B) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x0D) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x0E) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x0F) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x10) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x12) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x13) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x14) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x15) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x17) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x18) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x19) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x1A) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x1B) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x1C) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x31) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x32) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x33) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x34) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x35) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x36) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x3A) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x3B) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x3D) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x3E) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x3F) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x48) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x49) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x4A) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x4B) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x4C) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x61) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x62) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x63) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x64) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x65) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x66) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x6A) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x6B) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x6D) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x6E) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x6F) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x72) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x73) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x74) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x75) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x78) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x79) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x7A) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x7B) }, + { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0x06, 0x7C) }, { USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_V640) }, @@ -720,12 +1016,11 @@ static const struct usb_device_id option_ids[] = { { USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_MC547) }, { USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_EVDO_EMBEDDED_HIGHSPEED) }, { USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_HSPA_EMBEDDED_HIGHSPEED) }, - { USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_G1) }, - { USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_G1_M) }, { USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_G2) }, /* Novatel Ovation MC551 a.k.a. Verizon USB551L */ { USB_DEVICE_AND_INTERFACE_INFO(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_MC551, 0xff, 0xff, 0xff) }, { USB_DEVICE_AND_INTERFACE_INFO(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_E362, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_E371, 0xff, 0xff, 0xff) }, { USB_DEVICE(AMOI_VENDOR_ID, AMOI_PRODUCT_H01) }, { USB_DEVICE(AMOI_VENDOR_ID, AMOI_PRODUCT_H01A) }, @@ -750,6 +1045,7 @@ static const struct usb_device_id option_ids[] = { { USB_DEVICE(DELL_VENDOR_ID, DELL_PRODUCT_5730_MINICARD_VZW) }, /* Dell Wireless 5730 Mobile Broadband EVDO/HSPA Mini-Card */ { USB_DEVICE_AND_INTERFACE_INFO(DELL_VENDOR_ID, DELL_PRODUCT_5800_MINICARD_VZW, 0xff, 0xff, 0xff) }, { USB_DEVICE_AND_INTERFACE_INFO(DELL_VENDOR_ID, DELL_PRODUCT_5800_V2_MINICARD_VZW, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(DELL_VENDOR_ID, DELL_PRODUCT_5804_MINICARD_ATT, 0xff, 0xff, 0xff) }, { USB_DEVICE(ANYDATA_VENDOR_ID, ANYDATA_PRODUCT_ADU_E100A) }, /* ADU-E100, ADU-310 */ { USB_DEVICE(ANYDATA_VENDOR_ID, ANYDATA_PRODUCT_ADU_500A) }, { USB_DEVICE(ANYDATA_VENDOR_ID, ANYDATA_PRODUCT_ADU_620UW) }, @@ -774,16 +1070,58 @@ static const struct usb_device_id option_ids[] = { { USB_DEVICE_INTERFACE_CLASS(BANDRICH_VENDOR_ID, BANDRICH_PRODUCT_1012, 0xff) }, { USB_DEVICE(KYOCERA_VENDOR_ID, KYOCERA_PRODUCT_KPC650) }, { USB_DEVICE(KYOCERA_VENDOR_ID, KYOCERA_PRODUCT_KPC680) }, - { USB_DEVICE(QUALCOMM_VENDOR_ID, 0x6000)}, /* ZTE AC8700 */ { USB_DEVICE(QUALCOMM_VENDOR_ID, 0x6613)}, /* Onda H600/ZTE MF330 */ + { USB_DEVICE(QUALCOMM_VENDOR_ID, 0x0023)}, /* ONYX 3G device */ { USB_DEVICE(QUALCOMM_VENDOR_ID, 0x9000)}, /* SIMCom SIM5218 */ - { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_6280) }, /* BP3-USB & BP3-EXT HSDPA */ - { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_6008) }, + { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_6001) }, + { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_CMU_300) }, + { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_6003), + .driver_info = (kernel_ulong_t)&net_intf0_blacklist }, + { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_6004) }, + { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_6005) }, + { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_CGU_628A) }, + { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_CHE_628S), + .driver_info = (kernel_ulong_t)&net_intf0_blacklist }, + { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_CMU_301), + .driver_info = (kernel_ulong_t)&net_intf0_blacklist }, + { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_CHU_628), + .driver_info = (kernel_ulong_t)&net_intf0_blacklist }, + { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_CHU_628S) }, + { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_CDU_680) }, + { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_CDU_685A) }, + { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_CHU_720S), + .driver_info = (kernel_ulong_t)&net_intf0_blacklist }, + { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_7002), + .driver_info = (kernel_ulong_t)&net_intf0_blacklist }, + { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_CHU_629K), + .driver_info = (kernel_ulong_t)&net_intf4_blacklist }, + { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_7004), + .driver_info = (kernel_ulong_t)&net_intf3_blacklist }, + { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_7005) }, + { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_CGU_629), + .driver_info = (kernel_ulong_t)&net_intf5_blacklist }, + { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_CHU_629S), + .driver_info = (kernel_ulong_t)&net_intf4_blacklist }, + { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_CHU_720I), + .driver_info = (kernel_ulong_t)&net_intf0_blacklist }, + { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_7212), + .driver_info = (kernel_ulong_t)&net_intf0_blacklist }, + { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_7213), + .driver_info = (kernel_ulong_t)&net_intf0_blacklist }, + { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_7251), + .driver_info = (kernel_ulong_t)&net_intf1_blacklist }, + { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_7252), + .driver_info = (kernel_ulong_t)&net_intf1_blacklist }, + { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_7253), + .driver_info = (kernel_ulong_t)&net_intf1_blacklist }, { USB_DEVICE(TELIT_VENDOR_ID, TELIT_PRODUCT_UC864E) }, { USB_DEVICE(TELIT_VENDOR_ID, TELIT_PRODUCT_UC864G) }, { USB_DEVICE(TELIT_VENDOR_ID, TELIT_PRODUCT_CC864_DUAL) }, { USB_DEVICE(TELIT_VENDOR_ID, TELIT_PRODUCT_CC864_SINGLE) }, { USB_DEVICE(TELIT_VENDOR_ID, TELIT_PRODUCT_DE910_DUAL) }, + { USB_DEVICE(TELIT_VENDOR_ID, TELIT_PRODUCT_UE910_V2) }, + { USB_DEVICE(TELIT_VENDOR_ID, TELIT_PRODUCT_LE920), + .driver_info = (kernel_ulong_t)&telit_le920_blacklist }, { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_MF622, 0xff, 0xff, 0xff) }, /* ZTE WCDMA products */ { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0002, 0xff, 0xff, 0xff), .driver_info = (kernel_ulong_t)&net_intf1_blacklist }, @@ -809,7 +1147,8 @@ static const struct usb_device_id option_ids[] = { { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0017, 0xff, 0xff, 0xff), .driver_info = (kernel_ulong_t)&net_intf3_blacklist }, { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0018, 0xff, 0xff, 0xff) }, - { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0019, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0019, 0xff, 0xff, 0xff), + .driver_info = (kernel_ulong_t)&net_intf3_blacklist }, { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0020, 0xff, 0xff, 0xff) }, { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0021, 0xff, 0xff, 0xff), .driver_info = (kernel_ulong_t)&net_intf4_blacklist }, @@ -943,6 +1282,8 @@ static const struct usb_device_id option_ids[] = { .driver_info = (kernel_ulong_t)&net_intf4_blacklist }, { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0330, 0xff, 0xff, 0xff) }, { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0395, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0412, 0xff, 0xff, 0xff), /* Telewell TW-LTE 4G */ + .driver_info = (kernel_ulong_t)&net_intf4_blacklist }, { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0414, 0xff, 0xff, 0xff) }, { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0417, 0xff, 0xff, 0xff) }, { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1008, 0xff, 0xff, 0xff), @@ -1100,7 +1441,8 @@ static const struct usb_device_id option_ids[] = { { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1267, 0xff, 0xff, 0xff) }, { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1268, 0xff, 0xff, 0xff) }, { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1269, 0xff, 0xff, 0xff) }, - { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1270, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1270, 0xff, 0xff, 0xff), + .driver_info = (kernel_ulong_t)&net_intf5_blacklist }, { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1271, 0xff, 0xff, 0xff) }, { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1272, 0xff, 0xff, 0xff) }, { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1273, 0xff, 0xff, 0xff) }, @@ -1145,6 +1487,25 @@ static const struct usb_device_id option_ids[] = { .driver_info = (kernel_ulong_t)&net_intf2_blacklist }, { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1426, 0xff, 0xff, 0xff), /* ZTE MF91 */ .driver_info = (kernel_ulong_t)&net_intf2_blacklist }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1428, 0xff, 0xff, 0xff), /* Telewell TW-LTE 4G v2 */ + .driver_info = (kernel_ulong_t)&net_intf2_blacklist }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1533, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1534, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1535, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1545, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1546, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1547, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1565, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1566, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1567, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1589, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1590, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1591, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1592, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1594, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1596, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1598, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1600, 0xff, 0xff, 0xff) }, { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x2002, 0xff, 0xff, 0xff), .driver_info = (kernel_ulong_t)&zte_k3765_z_blacklist }, { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x2003, 0xff, 0xff, 0xff) }, @@ -1171,20 +1532,25 @@ static const struct usb_device_id option_ids[] = { .driver_info = (kernel_ulong_t)&net_intf3_blacklist }, { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0178, 0xff, 0xff, 0xff), .driver_info = (kernel_ulong_t)&net_intf3_blacklist }, - - { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_CDMA_TECH, 0xff, 0xff, 0xff) }, - { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_AC8710, 0xff, 0xff, 0xff) }, - { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_AC2726, 0xff, 0xff, 0xff) }, - { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_AC8710T, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xffe9, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff8b, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff8c, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff8d, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff8e, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff8f, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff90, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff91, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff92, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff93, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff94, 0xff, 0xff, 0xff) }, + + /* NOTE: most ZTE CDMA devices should be driven by zte_ev, not option */ { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_MC2718, 0xff, 0xff, 0xff), .driver_info = (kernel_ulong_t)&zte_mc2718_z_blacklist }, - { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_AD3812, 0xff, 0xff, 0xff), - .driver_info = (kernel_ulong_t)&zte_ad3812_z_blacklist }, - { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_MC2716, 0xff, 0xff, 0xff), - .driver_info = (kernel_ulong_t)&zte_mc2716_z_blacklist }, { USB_VENDOR_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff, 0x02, 0x01) }, { USB_VENDOR_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff, 0x02, 0x05) }, { USB_VENDOR_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff, 0x86, 0x10) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_AC2726, 0xff, 0xff, 0xff) }, { USB_DEVICE(BENQ_VENDOR_ID, BENQ_PRODUCT_H10) }, { USB_DEVICE(DLINK_VENDOR_ID, DLINK_PRODUCT_DWM_652) }, @@ -1203,15 +1569,26 @@ static const struct usb_device_id option_ids[] = { { USB_DEVICE(ALCATEL_VENDOR_ID, ALCATEL_PRODUCT_X060S_X200), .driver_info = (kernel_ulong_t)&alcatel_x200_blacklist }, - { USB_DEVICE(ALCATEL_VENDOR_ID, ALCATEL_PRODUCT_X220_X500D) }, + { USB_DEVICE(ALCATEL_VENDOR_ID, ALCATEL_PRODUCT_X220_X500D), + .driver_info = (kernel_ulong_t)&net_intf6_blacklist }, + { USB_DEVICE(ALCATEL_VENDOR_ID, 0x0052), + .driver_info = (kernel_ulong_t)&net_intf6_blacklist }, + { USB_DEVICE(ALCATEL_VENDOR_ID, 0x00b6), + .driver_info = (kernel_ulong_t)&net_intf3_blacklist }, + { USB_DEVICE(ALCATEL_VENDOR_ID, 0x00b7), + .driver_info = (kernel_ulong_t)&net_intf5_blacklist }, { USB_DEVICE(ALCATEL_VENDOR_ID, ALCATEL_PRODUCT_L100V), .driver_info = (kernel_ulong_t)&net_intf4_blacklist }, + { USB_DEVICE(ALCATEL_VENDOR_ID, ALCATEL_PRODUCT_L800MA), + .driver_info = (kernel_ulong_t)&net_intf2_blacklist }, { USB_DEVICE(AIRPLUS_VENDOR_ID, AIRPLUS_PRODUCT_MCD650) }, { USB_DEVICE(TLAYTECH_VENDOR_ID, TLAYTECH_PRODUCT_TEU800) }, { USB_DEVICE(LONGCHEER_VENDOR_ID, FOUR_G_SYSTEMS_PRODUCT_W14), .driver_info = (kernel_ulong_t)&four_g_w14_blacklist }, + { USB_DEVICE_INTERFACE_CLASS(LONGCHEER_VENDOR_ID, SPEEDUP_PRODUCT_SU9800, 0xff) }, { USB_DEVICE(LONGCHEER_VENDOR_ID, ZOOM_PRODUCT_4597) }, + { USB_DEVICE(LONGCHEER_VENDOR_ID, IBALL_3_5G_CONNECT) }, { USB_DEVICE(HAIER_VENDOR_ID, HAIER_PRODUCT_CE100) }, /* Pirelli */ { USB_DEVICE_INTERFACE_CLASS(PIRELLI_VENDOR_ID, PIRELLI_PRODUCT_C100_1, 0xff) }, @@ -1233,17 +1610,33 @@ static const struct usb_device_id option_ids[] = { /* Cinterion */ { USB_DEVICE(CINTERION_VENDOR_ID, CINTERION_PRODUCT_EU3_E) }, { USB_DEVICE(CINTERION_VENDOR_ID, CINTERION_PRODUCT_EU3_P) }, - { USB_DEVICE(CINTERION_VENDOR_ID, CINTERION_PRODUCT_PH8) }, + { USB_DEVICE(CINTERION_VENDOR_ID, CINTERION_PRODUCT_PH8), + .driver_info = (kernel_ulong_t)&net_intf4_blacklist }, + { USB_DEVICE(CINTERION_VENDOR_ID, CINTERION_PRODUCT_AHXX) }, + { USB_DEVICE(CINTERION_VENDOR_ID, CINTERION_PRODUCT_PLXX), + .driver_info = (kernel_ulong_t)&net_intf4_blacklist }, { USB_DEVICE(CINTERION_VENDOR_ID, CINTERION_PRODUCT_HC28_MDM) }, { USB_DEVICE(CINTERION_VENDOR_ID, CINTERION_PRODUCT_HC28_MDMNET) }, { USB_DEVICE(SIEMENS_VENDOR_ID, CINTERION_PRODUCT_HC25_MDM) }, { USB_DEVICE(SIEMENS_VENDOR_ID, CINTERION_PRODUCT_HC25_MDMNET) }, { USB_DEVICE(SIEMENS_VENDOR_ID, CINTERION_PRODUCT_HC28_MDM) }, /* HC28 enumerates with Siemens or Cinterion VID depending on FW revision */ { USB_DEVICE(SIEMENS_VENDOR_ID, CINTERION_PRODUCT_HC28_MDMNET) }, - - { USB_DEVICE(OLIVETTI_VENDOR_ID, OLIVETTI_PRODUCT_OLICARD100) }, + { USB_DEVICE(OLIVETTI_VENDOR_ID, OLIVETTI_PRODUCT_OLICARD100), + .driver_info = (kernel_ulong_t)&net_intf4_blacklist }, + { USB_DEVICE(OLIVETTI_VENDOR_ID, OLIVETTI_PRODUCT_OLICARD120), + .driver_info = (kernel_ulong_t)&net_intf4_blacklist }, + { USB_DEVICE(OLIVETTI_VENDOR_ID, OLIVETTI_PRODUCT_OLICARD140), + .driver_info = (kernel_ulong_t)&net_intf4_blacklist }, + { USB_DEVICE(OLIVETTI_VENDOR_ID, OLIVETTI_PRODUCT_OLICARD145) }, + { USB_DEVICE(OLIVETTI_VENDOR_ID, OLIVETTI_PRODUCT_OLICARD155), + .driver_info = (kernel_ulong_t)&net_intf6_blacklist }, + { USB_DEVICE(OLIVETTI_VENDOR_ID, OLIVETTI_PRODUCT_OLICARD200), + .driver_info = (kernel_ulong_t)&net_intf6_blacklist }, + { USB_DEVICE(OLIVETTI_VENDOR_ID, OLIVETTI_PRODUCT_OLICARD160), + .driver_info = (kernel_ulong_t)&net_intf6_blacklist }, + { USB_DEVICE(OLIVETTI_VENDOR_ID, OLIVETTI_PRODUCT_OLICARD500), + .driver_info = (kernel_ulong_t)&net_intf4_blacklist }, { USB_DEVICE(CELOT_VENDOR_ID, CELOT_PRODUCT_CT680M) }, /* CT-650 CDMA 450 1xEVDO modem */ - { USB_DEVICE(ONDA_VENDOR_ID, ONDA_MT825UP) }, /* ONDA MT825UP modem */ { USB_DEVICE_AND_INTERFACE_INFO(SAMSUNG_VENDOR_ID, SAMSUNG_PRODUCT_GT_B3730, USB_CLASS_CDC_DATA, 0x00, 0x00) }, /* Samsung GT-B3730 LTE USB modem.*/ { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CEM600) }, { USB_DEVICE(YUGA_VENDOR_ID, YUGA_PRODUCT_CEM610) }, @@ -1315,9 +1708,22 @@ static const struct usb_device_id option_ids[] = { { USB_DEVICE_AND_INTERFACE_INFO(MEDIATEK_VENDOR_ID, MEDIATEK_PRODUCT_DC_4COM2, 0xff, 0x02, 0x01) }, { USB_DEVICE_AND_INTERFACE_INFO(MEDIATEK_VENDOR_ID, MEDIATEK_PRODUCT_DC_4COM2, 0xff, 0x00, 0x00) }, { USB_DEVICE(CELLIENT_VENDOR_ID, CELLIENT_PRODUCT_MEN200) }, - { USB_DEVICE(PETATEL_VENDOR_ID, PETATEL_PRODUCT_NP10T) }, + { USB_DEVICE(PETATEL_VENDOR_ID, PETATEL_PRODUCT_NP10T_600A) }, + { USB_DEVICE(PETATEL_VENDOR_ID, PETATEL_PRODUCT_NP10T_600E) }, { USB_DEVICE(TPLINK_VENDOR_ID, TPLINK_PRODUCT_MA180), .driver_info = (kernel_ulong_t)&net_intf4_blacklist }, + { USB_DEVICE(TPLINK_VENDOR_ID, 0x9000), /* TP-Link MA260 */ + .driver_info = (kernel_ulong_t)&net_intf4_blacklist }, + { USB_DEVICE(CHANGHONG_VENDOR_ID, CHANGHONG_PRODUCT_CH690) }, + { USB_DEVICE_AND_INTERFACE_INFO(0x2001, 0x7d01, 0xff, 0x02, 0x01) }, /* D-Link DWM-156 (variant) */ + { USB_DEVICE_AND_INTERFACE_INFO(0x2001, 0x7d01, 0xff, 0x00, 0x00) }, /* D-Link DWM-156 (variant) */ + { USB_DEVICE_AND_INTERFACE_INFO(0x2001, 0x7d02, 0xff, 0x02, 0x01) }, + { USB_DEVICE_AND_INTERFACE_INFO(0x2001, 0x7d02, 0xff, 0x00, 0x00) }, + { USB_DEVICE_AND_INTERFACE_INFO(0x2001, 0x7d03, 0xff, 0x02, 0x01) }, + { USB_DEVICE_AND_INTERFACE_INFO(0x2001, 0x7d03, 0xff, 0x00, 0x00) }, + { USB_DEVICE_AND_INTERFACE_INFO(0x07d1, 0x3e01, 0xff, 0xff, 0xff) }, /* D-Link DWM-152/C1 */ + { USB_DEVICE_AND_INTERFACE_INFO(0x07d1, 0x3e02, 0xff, 0xff, 0xff) }, /* D-Link DWM-156/C1 */ + { USB_DEVICE(INOVIA_VENDOR_ID, INOVIA_SEW858) }, { } /* Terminating entry */ }; MODULE_DEVICE_TABLE(usb, option_ids); @@ -1341,7 +1747,6 @@ static struct usb_serial_driver option_1port_device = { .write = usb_wwan_write, .write_room = usb_wwan_write_room, .chars_in_buffer = usb_wwan_chars_in_buffer, - .set_termios = usb_wwan_set_termios, .tiocmget = usb_wwan_tiocmget, .tiocmset = usb_wwan_tiocmset, .ioctl = usb_wwan_ioctl, @@ -1505,13 +1910,8 @@ static void option_instat_callback(struct urb *urb) portdata->dsr_state = ((signals & 0x02) ? 1 : 0); portdata->ri_state = ((signals & 0x08) ? 1 : 0); - if (old_dcd_state && !portdata->dcd_state) { - struct tty_struct *tty = - tty_port_tty_get(&port->port); - if (tty && !C_CLOCAL(tty)) - tty_hangup(tty); - tty_kref_put(tty); - } + if (old_dcd_state && !portdata->dcd_state) + tty_port_tty_hangup(&port->port, true); } else { dev_dbg(dev, "%s: type %x req %x\n", __func__, req_pkt->bRequestType, req_pkt->bRequest); @@ -1521,6 +1921,7 @@ static void option_instat_callback(struct urb *urb) /* Resubmit urb so we continue receiving IRQ data */ if (status != -ESHUTDOWN && status != -ENOENT) { + usb_mark_last_busy(port->serial->dev); err = usb_submit_urb(urb, GFP_ATOMIC); if (err) dev_dbg(dev, "%s: resubmit intr urb failed. (%d)\n", @@ -1540,6 +1941,7 @@ static int option_send_setup(struct usb_serial_port *port) struct option_private *priv = intfdata->private; struct usb_wwan_port_private *portdata; int val = 0; + int res; portdata = usb_get_serial_port_data(port); @@ -1548,9 +1950,17 @@ static int option_send_setup(struct usb_serial_port *port) if (portdata->rts_state) val |= 0x02; - return usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0), + res = usb_autopm_get_interface(serial->interface); + if (res) + return res; + + res = usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0), 0x22, 0x21, val, priv->bInterfaceNumber, NULL, 0, USB_CTRL_SET_TIMEOUT); + + usb_autopm_put_interface(serial->interface); + + return res; } MODULE_AUTHOR(DRIVER_AUTHOR); diff --git a/drivers/usb/serial/oti6858.c b/drivers/usb/serial/oti6858.c index d217fd6ee43..a4b88bc038b 100644 --- a/drivers/usb/serial/oti6858.c +++ b/drivers/usb/serial/oti6858.c @@ -39,7 +39,6 @@ #include <linux/kernel.h> #include <linux/errno.h> -#include <linux/init.h> #include <linux/slab.h> #include <linux/tty.h> #include <linux/tty_driver.h> @@ -103,6 +102,7 @@ struct oti6858_control_pkt { #define TX_BUFFER_EMPTIED 0x09 u8 pin_state; #define PIN_MASK 0x3f +#define PIN_MSR_MASK 0x1b #define PIN_RTS 0x20 /* output pin */ #define PIN_CTS 0x10 /* input pin, active low */ #define PIN_DSR 0x08 /* input pin, active low */ @@ -124,8 +124,6 @@ static void oti6858_close(struct usb_serial_port *port); static void oti6858_set_termios(struct tty_struct *tty, struct usb_serial_port *port, struct ktermios *old); static void oti6858_init_termios(struct tty_struct *tty); -static int oti6858_ioctl(struct tty_struct *tty, - unsigned int cmd, unsigned long arg); static void oti6858_read_int_callback(struct urb *urb); static void oti6858_read_bulk_callback(struct urb *urb); static void oti6858_write_bulk_callback(struct urb *urb); @@ -150,11 +148,11 @@ static struct usb_serial_driver oti6858_device = { .open = oti6858_open, .close = oti6858_close, .write = oti6858_write, - .ioctl = oti6858_ioctl, .set_termios = oti6858_set_termios, .init_termios = oti6858_init_termios, .tiocmget = oti6858_tiocmget, .tiocmset = oti6858_tiocmset, + .tiocmiwait = usb_serial_generic_tiocmiwait, .read_bulk_callback = oti6858_read_bulk_callback, .read_int_callback = oti6858_read_int_callback, .write_bulk_callback = oti6858_write_bulk_callback, @@ -188,7 +186,6 @@ struct oti6858_private { u8 setup_done; struct delayed_work delayed_setup_work; - wait_queue_head_t intr_wait; struct usb_serial_port *port; /* USB port with which associated */ }; @@ -202,8 +199,7 @@ static void setup_line(struct work_struct *work) int result; new_setup = kmalloc(OTI6858_CTRL_PKT_SIZE, GFP_KERNEL); - if (new_setup == NULL) { - dev_err(&port->dev, "%s(): out of memory!\n", __func__); + if (!new_setup) { /* we will try again */ schedule_delayed_work(&priv->delayed_setup_work, msecs_to_jiffies(2)); @@ -289,11 +285,9 @@ static void send_data(struct work_struct *work) if (count != 0) { allow = kmalloc(1, GFP_KERNEL); - if (!allow) { - dev_err_console(port, "%s(): kmalloc failed\n", - __func__); + if (!allow) return; - } + result = usb_control_msg(port->serial->dev, usb_rcvctrlpipe(port->serial->dev, 0), OTI6858_REQ_T_CHECK_TXBUFF, @@ -339,13 +333,14 @@ static int oti6858_port_probe(struct usb_serial_port *port) return -ENOMEM; spin_lock_init(&priv->lock); - init_waitqueue_head(&priv->intr_wait); priv->port = port; INIT_DELAYED_WORK(&priv->delayed_setup_work, setup_line); INIT_DELAYED_WORK(&priv->delayed_write_work, send_data); usb_set_serial_port_data(port, priv); + port->port.drain_delay = 256; /* FIXME: check the FIFO length */ + return 0; } @@ -414,9 +409,6 @@ static void oti6858_set_termios(struct tty_struct *tty, __le16 divisor; int br; - if (!tty) - return; - cflag = tty->termios.c_cflag; spin_lock_irqsave(&priv->lock, flags); @@ -512,7 +504,6 @@ static void oti6858_set_termios(struct tty_struct *tty, static int oti6858_open(struct tty_struct *tty, struct usb_serial_port *port) { struct oti6858_private *priv = usb_get_serial_port_data(port); - struct ktermios tmp_termios; struct usb_serial *serial = port->serial; struct oti6858_control_pkt *buf; unsigned long flags; @@ -522,10 +513,8 @@ static int oti6858_open(struct tty_struct *tty, struct usb_serial_port *port) usb_clear_halt(serial->dev, port->read_urb->pipe); buf = kmalloc(OTI6858_CTRL_PKT_SIZE, GFP_KERNEL); - if (buf == NULL) { - dev_err(&port->dev, "%s(): out of memory!\n", __func__); + if (!buf) return -ENOMEM; - } result = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0), OTI6858_REQ_T_GET_STATUS, @@ -563,8 +552,8 @@ static int oti6858_open(struct tty_struct *tty, struct usb_serial_port *port) /* setup termios */ if (tty) - oti6858_set_termios(tty, port, &tmp_termios); - port->port.drain_delay = 256; /* FIXME: check the FIFO length */ + oti6858_set_termios(tty, port, NULL); + return 0; } @@ -652,59 +641,6 @@ static int oti6858_tiocmget(struct tty_struct *tty) return result; } -static int wait_modem_info(struct usb_serial_port *port, unsigned int arg) -{ - struct oti6858_private *priv = usb_get_serial_port_data(port); - unsigned long flags; - unsigned int prev, status; - unsigned int changed; - - spin_lock_irqsave(&priv->lock, flags); - prev = priv->status.pin_state; - spin_unlock_irqrestore(&priv->lock, flags); - - while (1) { - wait_event_interruptible(priv->intr_wait, - priv->status.pin_state != prev); - if (signal_pending(current)) - return -ERESTARTSYS; - - spin_lock_irqsave(&priv->lock, flags); - status = priv->status.pin_state & PIN_MASK; - spin_unlock_irqrestore(&priv->lock, flags); - - changed = prev ^ status; - /* FIXME: check if this is correct (active high/low) */ - if (((arg & TIOCM_RNG) && (changed & PIN_RI)) || - ((arg & TIOCM_DSR) && (changed & PIN_DSR)) || - ((arg & TIOCM_CD) && (changed & PIN_DCD)) || - ((arg & TIOCM_CTS) && (changed & PIN_CTS))) - return 0; - prev = status; - } - - /* NOTREACHED */ - return 0; -} - -static int oti6858_ioctl(struct tty_struct *tty, - unsigned int cmd, unsigned long arg) -{ - struct usb_serial_port *port = tty->driver_data; - - dev_dbg(&port->dev, "%s(cmd = 0x%04x, arg = 0x%08lx)\n", __func__, cmd, arg); - - switch (cmd) { - case TIOCMIWAIT: - dev_dbg(&port->dev, "%s(): TIOCMIWAIT\n", __func__); - return wait_modem_info(port, arg); - default: - dev_dbg(&port->dev, "%s(): 0x%04x not supported\n", __func__, cmd); - break; - } - return -ENOIOCTLCMD; -} - static void oti6858_read_int_callback(struct urb *urb) { struct usb_serial_port *port = urb->context; @@ -762,8 +698,21 @@ static void oti6858_read_int_callback(struct urb *urb) } if (!priv->transient) { - if (xs->pin_state != priv->status.pin_state) - wake_up_interruptible(&priv->intr_wait); + u8 delta = xs->pin_state ^ priv->status.pin_state; + + if (delta & PIN_MSR_MASK) { + if (delta & PIN_CTS) + port->icount.cts++; + if (delta & PIN_DSR) + port->icount.dsr++; + if (delta & PIN_RI) + port->icount.rng++; + if (delta & PIN_DCD) + port->icount.dcd++; + + wake_up_interruptible(&port->port.delta_msr_wait); + } + memcpy(&priv->status, xs, OTI6858_CTRL_PKT_SIZE); } @@ -820,7 +769,6 @@ static void oti6858_read_bulk_callback(struct urb *urb) { struct usb_serial_port *port = urb->context; struct oti6858_private *priv = usb_get_serial_port_data(port); - struct tty_struct *tty; unsigned char *data = urb->transfer_buffer; unsigned long flags; int status = urb->status; @@ -835,12 +783,10 @@ static void oti6858_read_bulk_callback(struct urb *urb) return; } - tty = tty_port_tty_get(&port->port); - if (tty != NULL && urb->actual_length > 0) { - tty_insert_flip_string(tty, data, urb->actual_length); - tty_flip_buffer_push(tty); + if (urb->actual_length > 0) { + tty_insert_flip_string(&port->port, data, urb->actual_length); + tty_flip_buffer_push(&port->port); } - tty_kref_put(tty); /* schedule the interrupt urb */ result = usb_submit_urb(port->interrupt_in_urb, GFP_ATOMIC); diff --git a/drivers/usb/serial/pl2303.c b/drivers/usb/serial/pl2303.c index 60024190136..b3d5a35c0d4 100644 --- a/drivers/usb/serial/pl2303.c +++ b/drivers/usb/serial/pl2303.c @@ -12,12 +12,10 @@ * * See Documentation/usb/usb-serial.txt for more information on using this * driver - * */ #include <linux/kernel.h> #include <linux/errno.h> -#include <linux/init.h> #include <linux/slab.h> #include <linux/tty.h> #include <linux/tty_driver.h> @@ -29,12 +27,12 @@ #include <linux/uaccess.h> #include <linux/usb.h> #include <linux/usb/serial.h> +#include <asm/unaligned.h> #include "pl2303.h" -/* - * Version Information - */ -#define DRIVER_DESC "Prolific PL2303 USB to serial adaptor driver" + +#define PL2303_QUIRK_UART_STATE_IDX0 BIT(0) +#define PL2303_QUIRK_LEGACY BIT(1) static const struct usb_device_id id_table[] = { { USB_DEVICE(PL2303_VENDOR_ID, PL2303_PRODUCT_ID) }, @@ -63,9 +61,12 @@ static const struct usb_device_id id_table[] = { { USB_DEVICE(SITECOM_VENDOR_ID, SITECOM_PRODUCT_ID) }, { USB_DEVICE(ALCATEL_VENDOR_ID, ALCATEL_PRODUCT_ID) }, { USB_DEVICE(SAMSUNG_VENDOR_ID, SAMSUNG_PRODUCT_ID) }, - { USB_DEVICE(SIEMENS_VENDOR_ID, SIEMENS_PRODUCT_ID_SX1) }, - { USB_DEVICE(SIEMENS_VENDOR_ID, SIEMENS_PRODUCT_ID_X65) }, - { USB_DEVICE(SIEMENS_VENDOR_ID, SIEMENS_PRODUCT_ID_X75) }, + { USB_DEVICE(SIEMENS_VENDOR_ID, SIEMENS_PRODUCT_ID_SX1), + .driver_info = PL2303_QUIRK_UART_STATE_IDX0 }, + { USB_DEVICE(SIEMENS_VENDOR_ID, SIEMENS_PRODUCT_ID_X65), + .driver_info = PL2303_QUIRK_UART_STATE_IDX0 }, + { USB_DEVICE(SIEMENS_VENDOR_ID, SIEMENS_PRODUCT_ID_X75), + .driver_info = PL2303_QUIRK_UART_STATE_IDX0 }, { USB_DEVICE(SIEMENS_VENDOR_ID, SIEMENS_PRODUCT_ID_EF81) }, { USB_DEVICE(BENQ_VENDOR_ID, BENQ_PRODUCT_ID_S81) }, /* Benq/Siemens S81 */ { USB_DEVICE(SYNTECH_VENDOR_ID, SYNTECH_PRODUCT_ID) }, @@ -82,6 +83,9 @@ static const struct usb_device_id id_table[] = { { USB_DEVICE(YCCABLE_VENDOR_ID, YCCABLE_PRODUCT_ID) }, { USB_DEVICE(SUPERIAL_VENDOR_ID, SUPERIAL_PRODUCT_ID) }, { USB_DEVICE(HP_VENDOR_ID, HP_LD220_PRODUCT_ID) }, + { USB_DEVICE(HP_VENDOR_ID, HP_LD960_PRODUCT_ID) }, + { USB_DEVICE(HP_VENDOR_ID, HP_LCM220_PRODUCT_ID) }, + { USB_DEVICE(HP_VENDOR_ID, HP_LCM960_PRODUCT_ID) }, { USB_DEVICE(CRESSI_VENDOR_ID, CRESSI_EDY_PRODUCT_ID) }, { USB_DEVICE(ZEAGLE_VENDOR_ID, ZEAGLE_N2ITION3_PRODUCT_ID) }, { USB_DEVICE(SONY_VENDOR_ID, SONY_QN3USB_PRODUCT_ID) }, @@ -115,7 +119,8 @@ MODULE_DEVICE_TABLE(usb, id_table); #define VENDOR_READ_REQUEST_TYPE 0xc0 #define VENDOR_READ_REQUEST 0x01 -#define UART_STATE 0x08 +#define UART_STATE_INDEX 8 +#define UART_STATE_MSR_MASK 0x8b #define UART_STATE_TRANSIENT_MASK 0x74 #define UART_DCD 0x01 #define UART_DSR 0x02 @@ -128,99 +133,142 @@ MODULE_DEVICE_TABLE(usb, id_table); enum pl2303_type { - type_0, /* don't know the difference between type 0 and */ - type_1, /* type 1, until someone from prolific tells us... */ - HX, /* HX version of the pl2303 chip */ + TYPE_01, /* Type 0 and 1 (difference unknown) */ + TYPE_HX, /* HX version of the pl2303 chip */ + TYPE_COUNT +}; + +struct pl2303_type_data { + speed_t max_baud_rate; + unsigned long quirks; }; struct pl2303_serial_private { - enum pl2303_type type; + const struct pl2303_type_data *type; + unsigned long quirks; }; struct pl2303_private { spinlock_t lock; - wait_queue_head_t delta_msr_wait; u8 line_control; u8 line_status; + + u8 line_settings[7]; }; -static int pl2303_vendor_read(__u16 value, __u16 index, - struct usb_serial *serial, unsigned char *buf) +static const struct pl2303_type_data pl2303_type_data[TYPE_COUNT] = { + [TYPE_01] = { + .max_baud_rate = 1228800, + .quirks = PL2303_QUIRK_LEGACY, + }, +}; + +static int pl2303_vendor_read(struct usb_serial *serial, u16 value, + unsigned char buf[1]) { - int res = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0), + struct device *dev = &serial->interface->dev; + int res; + + res = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0), VENDOR_READ_REQUEST, VENDOR_READ_REQUEST_TYPE, - value, index, buf, 1, 100); - dev_dbg(&serial->dev->dev, "0x%x:0x%x:0x%x:0x%x %d - %x\n", - VENDOR_READ_REQUEST_TYPE, VENDOR_READ_REQUEST, value, index, - res, buf[0]); - return res; + value, 0, buf, 1, 100); + if (res != 1) { + dev_err(dev, "%s - failed to read [%04x]: %d\n", __func__, + value, res); + if (res >= 0) + res = -EIO; + + return res; + } + + dev_dbg(dev, "%s - [%04x] = %02x\n", __func__, value, buf[0]); + + return 0; } -static int pl2303_vendor_write(__u16 value, __u16 index, - struct usb_serial *serial) +static int pl2303_vendor_write(struct usb_serial *serial, u16 value, u16 index) { - int res = usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0), + struct device *dev = &serial->interface->dev; + int res; + + dev_dbg(dev, "%s - [%04x] = %02x\n", __func__, value, index); + + res = usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0), VENDOR_WRITE_REQUEST, VENDOR_WRITE_REQUEST_TYPE, value, index, NULL, 0, 100); - dev_dbg(&serial->dev->dev, "0x%x:0x%x:0x%x:0x%x %d\n", - VENDOR_WRITE_REQUEST_TYPE, VENDOR_WRITE_REQUEST, value, index, - res); - return res; + if (res) { + dev_err(dev, "%s - failed to write [%04x]: %d\n", __func__, + value, res); + return res; + } + + return 0; +} + +static int pl2303_probe(struct usb_serial *serial, + const struct usb_device_id *id) +{ + usb_set_serial_data(serial, (void *)id->driver_info); + + return 0; } static int pl2303_startup(struct usb_serial *serial) { struct pl2303_serial_private *spriv; - enum pl2303_type type = type_0; + enum pl2303_type type = TYPE_01; unsigned char *buf; spriv = kzalloc(sizeof(*spriv), GFP_KERNEL); if (!spriv) return -ENOMEM; - buf = kmalloc(10, GFP_KERNEL); + buf = kmalloc(1, GFP_KERNEL); if (!buf) { kfree(spriv); return -ENOMEM; } if (serial->dev->descriptor.bDeviceClass == 0x02) - type = type_0; + type = TYPE_01; /* type 0 */ else if (serial->dev->descriptor.bMaxPacketSize0 == 0x40) - type = HX; + type = TYPE_HX; else if (serial->dev->descriptor.bDeviceClass == 0x00) - type = type_1; + type = TYPE_01; /* type 1 */ else if (serial->dev->descriptor.bDeviceClass == 0xFF) - type = type_1; + type = TYPE_01; /* type 1 */ dev_dbg(&serial->interface->dev, "device type: %d\n", type); - spriv->type = type; + spriv->type = &pl2303_type_data[type]; + spriv->quirks = (unsigned long)usb_get_serial_data(serial); + spriv->quirks |= spriv->type->quirks; + usb_set_serial_data(serial, spriv); - pl2303_vendor_read(0x8484, 0, serial, buf); - pl2303_vendor_write(0x0404, 0, serial); - pl2303_vendor_read(0x8484, 0, serial, buf); - pl2303_vendor_read(0x8383, 0, serial, buf); - pl2303_vendor_read(0x8484, 0, serial, buf); - pl2303_vendor_write(0x0404, 1, serial); - pl2303_vendor_read(0x8484, 0, serial, buf); - pl2303_vendor_read(0x8383, 0, serial, buf); - pl2303_vendor_write(0, 1, serial); - pl2303_vendor_write(1, 0, serial); - if (type == HX) - pl2303_vendor_write(2, 0x44, serial); + pl2303_vendor_read(serial, 0x8484, buf); + pl2303_vendor_write(serial, 0x0404, 0); + pl2303_vendor_read(serial, 0x8484, buf); + pl2303_vendor_read(serial, 0x8383, buf); + pl2303_vendor_read(serial, 0x8484, buf); + pl2303_vendor_write(serial, 0x0404, 1); + pl2303_vendor_read(serial, 0x8484, buf); + pl2303_vendor_read(serial, 0x8383, buf); + pl2303_vendor_write(serial, 0, 1); + pl2303_vendor_write(serial, 1, 0); + if (spriv->quirks & PL2303_QUIRK_LEGACY) + pl2303_vendor_write(serial, 2, 0x24); else - pl2303_vendor_write(2, 0x24, serial); + pl2303_vendor_write(serial, 2, 0x44); kfree(buf); + return 0; } static void pl2303_release(struct usb_serial *serial) { - struct pl2303_serial_private *spriv; + struct pl2303_serial_private *spriv = usb_get_serial_data(serial); - spriv = usb_get_serial_data(serial); kfree(spriv); } @@ -233,35 +281,181 @@ static int pl2303_port_probe(struct usb_serial_port *port) return -ENOMEM; spin_lock_init(&priv->lock); - init_waitqueue_head(&priv->delta_msr_wait); usb_set_serial_port_data(port, priv); + port->port.drain_delay = 256; + return 0; } static int pl2303_port_remove(struct usb_serial_port *port) { - struct pl2303_private *priv; + struct pl2303_private *priv = usb_get_serial_port_data(port); - priv = usb_get_serial_port_data(port); kfree(priv); return 0; } -static int set_control_lines(struct usb_device *dev, u8 value) +static int pl2303_set_control_lines(struct usb_serial_port *port, u8 value) { + struct usb_device *dev = port->serial->dev; int retval; + dev_dbg(&port->dev, "%s - %02x\n", __func__, value); + retval = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), SET_CONTROL_REQUEST, SET_CONTROL_REQUEST_TYPE, value, 0, NULL, 0, 100); - dev_dbg(&dev->dev, "%s - value = %d, retval = %d\n", __func__, - value, retval); + if (retval) + dev_err(&port->dev, "%s - failed: %d\n", __func__, retval); + return retval; } +/* + * Returns the nearest supported baud rate that can be set directly without + * using divisors. + */ +static speed_t pl2303_get_supported_baud_rate(speed_t baud) +{ + static const speed_t baud_sup[] = { + 75, 150, 300, 600, 1200, 1800, 2400, 3600, 4800, 7200, 9600, + 14400, 19200, 28800, 38400, 57600, 115200, 230400, 460800, + 614400, 921600, 1228800, 2457600, 3000000, 6000000 + }; + + unsigned i; + + for (i = 0; i < ARRAY_SIZE(baud_sup); ++i) { + if (baud_sup[i] > baud) + break; + } + + if (i == ARRAY_SIZE(baud_sup)) + baud = baud_sup[i - 1]; + else if (i > 0 && (baud_sup[i] - baud) > (baud - baud_sup[i - 1])) + baud = baud_sup[i - 1]; + else + baud = baud_sup[i]; + + return baud; +} + +/* + * NOTE: If unsupported baud rates are set directly, the PL2303 seems to + * use 9600 baud. + */ +static speed_t pl2303_encode_baud_rate_direct(unsigned char buf[4], + speed_t baud) +{ + put_unaligned_le32(baud, buf); + + return baud; +} + +static speed_t pl2303_encode_baud_rate_divisor(unsigned char buf[4], + speed_t baud) +{ + unsigned int tmp; + + /* + * Apparently the formula is: + * baudrate = 12M * 32 / (2^buf[1]) / buf[0] + */ + tmp = 12000000 * 32 / baud; + buf[3] = 0x80; + buf[2] = 0; + buf[1] = (tmp >= 256); + while (tmp >= 256) { + tmp >>= 2; + buf[1] <<= 1; + } + buf[0] = tmp; + + return baud; +} + +static void pl2303_encode_baud_rate(struct tty_struct *tty, + struct usb_serial_port *port, + u8 buf[4]) +{ + struct usb_serial *serial = port->serial; + struct pl2303_serial_private *spriv = usb_get_serial_data(serial); + speed_t baud_sup; + speed_t baud; + + baud = tty_get_baud_rate(tty); + dev_dbg(&port->dev, "baud requested = %u\n", baud); + if (!baud) + return; + + if (spriv->type->max_baud_rate) + baud = min_t(speed_t, baud, spriv->type->max_baud_rate); + /* + * Set baud rate to nearest supported value. + * + * NOTE: Baud rate 500k can only be set using divisors. + */ + baud_sup = pl2303_get_supported_baud_rate(baud); + + if (baud == 500000) + baud = pl2303_encode_baud_rate_divisor(buf, baud); + else + baud = pl2303_encode_baud_rate_direct(buf, baud_sup); + + /* Save resulting baud rate */ + tty_encode_baud_rate(tty, baud, baud); + dev_dbg(&port->dev, "baud set = %u\n", baud); +} + +static int pl2303_get_line_request(struct usb_serial_port *port, + unsigned char buf[7]) +{ + struct usb_device *udev = port->serial->dev; + int ret; + + ret = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0), + GET_LINE_REQUEST, GET_LINE_REQUEST_TYPE, + 0, 0, buf, 7, 100); + if (ret != 7) { + dev_err(&port->dev, "%s - failed: %d\n", __func__, ret); + + if (ret > 0) + ret = -EIO; + + return ret; + } + + dev_dbg(&port->dev, "%s - %7ph\n", __func__, buf); + + return 0; +} + +static int pl2303_set_line_request(struct usb_serial_port *port, + unsigned char buf[7]) +{ + struct usb_device *udev = port->serial->dev; + int ret; + + ret = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), + SET_LINE_REQUEST, SET_LINE_REQUEST_TYPE, + 0, 0, buf, 7, 100); + if (ret != 7) { + dev_err(&port->dev, "%s - failed: %d\n", __func__, ret); + + if (ret > 0) + ret = -EIO; + + return ret; + } + + dev_dbg(&port->dev, "%s - %7ph\n", __func__, buf); + + return 0; +} + static void pl2303_set_termios(struct tty_struct *tty, struct usb_serial_port *port, struct ktermios *old_termios) { @@ -269,122 +463,51 @@ static void pl2303_set_termios(struct tty_struct *tty, struct pl2303_serial_private *spriv = usb_get_serial_data(serial); struct pl2303_private *priv = usb_get_serial_port_data(port); unsigned long flags; - unsigned int cflag; unsigned char *buf; - int baud; - int i; + int ret; u8 control; - const int baud_sup[] = { 75, 150, 300, 600, 1200, 1800, 2400, 3600, - 4800, 7200, 9600, 14400, 19200, 28800, 38400, - 57600, 115200, 230400, 460800, 614400, - 921600, 1228800, 2457600, 3000000, 6000000 }; - int baud_floor, baud_ceil; - int k; - - /* The PL2303 is reported to lose bytes if you change - serial settings even to the same values as before. Thus - we actually need to filter in this specific case */ - - if (!tty_termios_hw_change(&tty->termios, old_termios)) - return; - cflag = tty->termios.c_cflag; + if (old_termios && !tty_termios_hw_change(&tty->termios, old_termios)) + return; buf = kzalloc(7, GFP_KERNEL); if (!buf) { - dev_err(&port->dev, "%s - out of memory.\n", __func__); /* Report back no change occurred */ - tty->termios = *old_termios; + if (old_termios) + tty->termios = *old_termios; return; } - i = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0), - GET_LINE_REQUEST, GET_LINE_REQUEST_TYPE, - 0, 0, buf, 7, 100); - dev_dbg(&port->dev, "0xa1:0x21:0:0 %d - %x %x %x %x %x %x %x\n", i, - buf[0], buf[1], buf[2], buf[3], buf[4], buf[5], buf[6]); + pl2303_get_line_request(port, buf); - if (cflag & CSIZE) { - switch (cflag & CSIZE) { - case CS5: - buf[6] = 5; - break; - case CS6: - buf[6] = 6; - break; - case CS7: - buf[6] = 7; - break; - default: - case CS8: - buf[6] = 8; - break; - } - dev_dbg(&port->dev, "data bits = %d\n", buf[6]); + switch (C_CSIZE(tty)) { + case CS5: + buf[6] = 5; + break; + case CS6: + buf[6] = 6; + break; + case CS7: + buf[6] = 7; + break; + default: + case CS8: + buf[6] = 8; } + dev_dbg(&port->dev, "data bits = %d\n", buf[6]); /* For reference buf[0]:buf[3] baud rate value */ - /* NOTE: Only the values defined in baud_sup are supported ! - * => if unsupported values are set, the PL2303 seems to use - * 9600 baud (at least my PL2303X always does) - */ - baud = tty_get_baud_rate(tty); - dev_dbg(&port->dev, "baud requested = %d\n", baud); - if (baud) { - /* Set baudrate to nearest supported value */ - for (k=0; k<ARRAY_SIZE(baud_sup); k++) { - if (baud_sup[k] / baud) { - baud_ceil = baud_sup[k]; - if (k==0) { - baud = baud_ceil; - } else { - baud_floor = baud_sup[k-1]; - if ((baud_ceil % baud) - > (baud % baud_floor)) - baud = baud_floor; - else - baud = baud_ceil; - } - break; - } - } - if (baud > 1228800) { - /* type_0, type_1 only support up to 1228800 baud */ - if (spriv->type != HX) - baud = 1228800; - else if (baud > 6000000) - baud = 6000000; - } - dev_dbg(&port->dev, "baud set = %d\n", baud); - if (baud <= 115200) { - buf[0] = baud & 0xff; - buf[1] = (baud >> 8) & 0xff; - buf[2] = (baud >> 16) & 0xff; - buf[3] = (baud >> 24) & 0xff; - } else { - /* apparently the formula for higher speeds is: - * baudrate = 12M * 32 / (2^buf[1]) / buf[0] - */ - unsigned tmp = 12*1000*1000*32 / baud; - buf[3] = 0x80; - buf[2] = 0; - buf[1] = (tmp >= 256); - while (tmp >= 256) { - tmp >>= 2; - buf[1] <<= 1; - } - buf[0] = tmp; - } - } + pl2303_encode_baud_rate(tty, port, &buf[0]); /* For reference buf[4]=0 is 1 stop bits */ /* For reference buf[4]=1 is 1.5 stop bits */ /* For reference buf[4]=2 is 2 stop bits */ - if (cflag & CSTOPB) { - /* NOTE: Comply with "real" UARTs / RS232: + if (C_CSTOPB(tty)) { + /* + * NOTE: Comply with "real" UARTs / RS232: * use 1.5 instead of 2 stop bits with 5 data bits */ - if ((cflag & CSIZE) == CS5) { + if (C_CSIZE(tty) == CS5) { buf[4] = 1; dev_dbg(&port->dev, "stop bits = 1.5\n"); } else { @@ -396,14 +519,14 @@ static void pl2303_set_termios(struct tty_struct *tty, dev_dbg(&port->dev, "stop bits = 1\n"); } - if (cflag & PARENB) { + if (C_PARENB(tty)) { /* For reference buf[5]=0 is none parity */ /* For reference buf[5]=1 is odd parity */ /* For reference buf[5]=2 is even parity */ /* For reference buf[5]=3 is mark parity */ /* For reference buf[5]=4 is space parity */ - if (cflag & PARODD) { - if (cflag & CMSPAR) { + if (C_PARODD(tty)) { + if (C_CMSPAR(tty)) { buf[5] = 3; dev_dbg(&port->dev, "parity = mark\n"); } else { @@ -411,7 +534,7 @@ static void pl2303_set_termios(struct tty_struct *tty, dev_dbg(&port->dev, "parity = odd\n"); } } else { - if (cflag & CMSPAR) { + if (C_CMSPAR(tty)) { buf[5] = 4; dev_dbg(&port->dev, "parity = space\n"); } else { @@ -424,47 +547,48 @@ static void pl2303_set_termios(struct tty_struct *tty, dev_dbg(&port->dev, "parity = none\n"); } - i = usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0), - SET_LINE_REQUEST, SET_LINE_REQUEST_TYPE, - 0, 0, buf, 7, 100); - dev_dbg(&port->dev, "0x21:0x20:0:0 %d\n", i); + /* + * Some PL2303 are known to lose bytes if you change serial settings + * even to the same values as before. Thus we actually need to filter + * in this specific case. + * + * Note that the tty_termios_hw_change check above is not sufficient + * as a previously requested baud rate may differ from the one + * actually used (and stored in old_termios). + * + * NOTE: No additional locking needed for line_settings as it is + * only used in set_termios, which is serialised against itself. + */ + if (!old_termios || memcmp(buf, priv->line_settings, 7)) { + ret = pl2303_set_line_request(port, buf); + if (!ret) + memcpy(priv->line_settings, buf, 7); + } /* change control lines if we are switching to or from B0 */ spin_lock_irqsave(&priv->lock, flags); control = priv->line_control; - if ((cflag & CBAUD) == B0) + if (C_BAUD(tty) == B0) priv->line_control &= ~(CONTROL_DTR | CONTROL_RTS); - else if ((old_termios->c_cflag & CBAUD) == B0) + else if (old_termios && (old_termios->c_cflag & CBAUD) == B0) priv->line_control |= (CONTROL_DTR | CONTROL_RTS); if (control != priv->line_control) { control = priv->line_control; spin_unlock_irqrestore(&priv->lock, flags); - set_control_lines(serial->dev, control); + pl2303_set_control_lines(port, control); } else { spin_unlock_irqrestore(&priv->lock, flags); } - buf[0] = buf[1] = buf[2] = buf[3] = buf[4] = buf[5] = buf[6] = 0; - - i = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0), - GET_LINE_REQUEST, GET_LINE_REQUEST_TYPE, - 0, 0, buf, 7, 100); - dev_dbg(&port->dev, "0xa1:0x21:0:0 %d - %x %x %x %x %x %x %x\n", i, - buf[0], buf[1], buf[2], buf[3], buf[4], buf[5], buf[6]); - - if (cflag & CRTSCTS) { - if (spriv->type == HX) - pl2303_vendor_write(0x0, 0x61, serial); + if (C_CRTSCTS(tty)) { + if (spriv->quirks & PL2303_QUIRK_LEGACY) + pl2303_vendor_write(serial, 0x0, 0x41); else - pl2303_vendor_write(0x0, 0x41, serial); + pl2303_vendor_write(serial, 0x0, 0x61); } else { - pl2303_vendor_write(0x0, 0x0, serial); + pl2303_vendor_write(serial, 0x0, 0x0); } - /* Save resulting baud rate */ - if (baud) - tty_encode_baud_rate(tty, baud, baud); - kfree(buf); } @@ -475,14 +599,14 @@ static void pl2303_dtr_rts(struct usb_serial_port *port, int on) u8 control; spin_lock_irqsave(&priv->lock, flags); - /* Change DTR and RTS */ if (on) priv->line_control |= (CONTROL_DTR | CONTROL_RTS); else priv->line_control &= ~(CONTROL_DTR | CONTROL_RTS); control = priv->line_control; spin_unlock_irqrestore(&priv->lock, flags); - set_control_lines(port->serial->dev, control); + + pl2303_set_control_lines(port, control); } static void pl2303_close(struct usb_serial_port *port) @@ -493,28 +617,27 @@ static void pl2303_close(struct usb_serial_port *port) static int pl2303_open(struct tty_struct *tty, struct usb_serial_port *port) { - struct ktermios tmp_termios; struct usb_serial *serial = port->serial; struct pl2303_serial_private *spriv = usb_get_serial_data(serial); int result; - if (spriv->type != HX) { + if (spriv->quirks & PL2303_QUIRK_LEGACY) { usb_clear_halt(serial->dev, port->write_urb->pipe); usb_clear_halt(serial->dev, port->read_urb->pipe); } else { /* reset upstream data pipes */ - pl2303_vendor_write(8, 0, serial); - pl2303_vendor_write(9, 0, serial); + pl2303_vendor_write(serial, 8, 0); + pl2303_vendor_write(serial, 9, 0); } /* Setup termios */ if (tty) - pl2303_set_termios(tty, port, &tmp_termios); + pl2303_set_termios(tty, port, NULL); result = usb_submit_urb(port->interrupt_in_urb, GFP_KERNEL); if (result) { - dev_err(&port->dev, "%s - failed submitting interrupt urb," - " error %d\n", __func__, result); + dev_err(&port->dev, "failed to submit interrupt urb: %d\n", + result); return result; } @@ -524,7 +647,6 @@ static int pl2303_open(struct tty_struct *tty, struct usb_serial_port *port) return result; } - port->port.drain_delay = 256; return 0; } @@ -532,7 +654,6 @@ static int pl2303_tiocmset(struct tty_struct *tty, unsigned int set, unsigned int clear) { struct usb_serial_port *port = tty->driver_data; - struct usb_serial *serial = port->serial; struct pl2303_private *priv = usb_get_serial_port_data(port); unsigned long flags; u8 control; @@ -550,14 +671,11 @@ static int pl2303_tiocmset(struct tty_struct *tty, control = priv->line_control; spin_unlock_irqrestore(&priv->lock, flags); - mutex_lock(&serial->disc_mutex); - if (!serial->disconnected) - ret = set_control_lines(serial->dev, control); - else - ret = -ENODEV; - mutex_unlock(&serial->disc_mutex); + ret = pl2303_set_control_lines(port, control); + if (ret) + return usb_translate_errors(ret); - return ret; + return 0; } static int pl2303_tiocmget(struct tty_struct *tty) @@ -589,44 +707,10 @@ static int pl2303_tiocmget(struct tty_struct *tty) static int pl2303_carrier_raised(struct usb_serial_port *port) { struct pl2303_private *priv = usb_get_serial_port_data(port); + if (priv->line_status & UART_DCD) return 1; - return 0; -} - -static int wait_modem_info(struct usb_serial_port *port, unsigned int arg) -{ - struct pl2303_private *priv = usb_get_serial_port_data(port); - unsigned long flags; - unsigned int prevstatus; - unsigned int status; - unsigned int changed; - - spin_lock_irqsave(&priv->lock, flags); - prevstatus = priv->line_status; - spin_unlock_irqrestore(&priv->lock, flags); - - while (1) { - interruptible_sleep_on(&priv->delta_msr_wait); - /* see if a signal did it */ - if (signal_pending(current)) - return -ERESTARTSYS; - - spin_lock_irqsave(&priv->lock, flags); - status = priv->line_status; - spin_unlock_irqrestore(&priv->lock, flags); - - changed = prevstatus ^ status; - if (((arg & TIOCM_RNG) && (changed & UART_RING)) || - ((arg & TIOCM_DSR) && (changed & UART_DSR)) || - ((arg & TIOCM_CD) && (changed & UART_DCD)) || - ((arg & TIOCM_CTS) && (changed & UART_CTS))) { - return 0; - } - prevstatus = status; - } - /* NOTREACHED */ return 0; } @@ -636,28 +720,22 @@ static int pl2303_ioctl(struct tty_struct *tty, struct serial_struct ser; struct usb_serial_port *port = tty->driver_data; - dev_dbg(&port->dev, "%s cmd = 0x%04x\n", __func__, cmd); - switch (cmd) { case TIOCGSERIAL: memset(&ser, 0, sizeof ser); ser.type = PORT_16654; - ser.line = port->serial->minor; - ser.port = port->number; + ser.line = port->minor; + ser.port = port->port_number; ser.baud_base = 460800; if (copy_to_user((void __user *)arg, &ser, sizeof ser)) return -EFAULT; return 0; - - case TIOCMIWAIT: - dev_dbg(&port->dev, "%s TIOCMIWAIT\n", __func__); - return wait_modem_info(port, arg); default: - dev_dbg(&port->dev, "%s not supported = 0x%04x\n", __func__, cmd); break; } + return -ENOIOCTLCMD; } @@ -672,6 +750,7 @@ static void pl2303_break_ctl(struct tty_struct *tty, int break_state) state = BREAK_OFF; else state = BREAK_ON; + dev_dbg(&port->dev, "%s - turning break %s\n", __func__, state == BREAK_OFF ? "off" : "on"); @@ -686,48 +765,51 @@ static void pl2303_update_line_status(struct usb_serial_port *port, unsigned char *data, unsigned int actual_length) { - + struct usb_serial *serial = port->serial; + struct pl2303_serial_private *spriv = usb_get_serial_data(serial); struct pl2303_private *priv = usb_get_serial_port_data(port); struct tty_struct *tty; unsigned long flags; - u8 status_idx = UART_STATE; - u8 length = UART_STATE + 1; - u8 prev_line_status; - u16 idv, idp; + unsigned int status_idx = UART_STATE_INDEX; + u8 status; + u8 delta; - idv = le16_to_cpu(port->serial->dev->descriptor.idVendor); - idp = le16_to_cpu(port->serial->dev->descriptor.idProduct); + if (spriv->quirks & PL2303_QUIRK_UART_STATE_IDX0) + status_idx = 0; - - if (idv == SIEMENS_VENDOR_ID) { - if (idp == SIEMENS_PRODUCT_ID_X65 || - idp == SIEMENS_PRODUCT_ID_SX1 || - idp == SIEMENS_PRODUCT_ID_X75) { - - length = 1; - status_idx = 0; - } - } - - if (actual_length < length) + if (actual_length < status_idx + 1) return; + status = data[status_idx]; + /* Save off the uart status for others to look at */ spin_lock_irqsave(&priv->lock, flags); - prev_line_status = priv->line_status; - priv->line_status = data[status_idx]; + delta = priv->line_status ^ status; + priv->line_status = status; spin_unlock_irqrestore(&priv->lock, flags); - if (priv->line_status & UART_BREAK_ERROR) + + if (status & UART_BREAK_ERROR) usb_serial_handle_break(port); - wake_up_interruptible(&priv->delta_msr_wait); - tty = tty_port_tty_get(&port->port); - if (!tty) - return; - if ((priv->line_status ^ prev_line_status) & UART_DCD) - usb_serial_handle_dcd_change(port, tty, - priv->line_status & UART_DCD); - tty_kref_put(tty); + if (delta & UART_STATE_MSR_MASK) { + if (delta & UART_CTS) + port->icount.cts++; + if (delta & UART_DSR) + port->icount.dsr++; + if (delta & UART_RING) + port->icount.rng++; + if (delta & UART_DCD) { + port->icount.dcd++; + tty = tty_port_tty_get(&port->port); + if (tty) { + usb_serial_handle_dcd_change(port, tty, + status & UART_DCD); + tty_kref_put(tty); + } + } + + wake_up_interruptible(&port->port.delta_msr_wait); + } } static void pl2303_read_int_callback(struct urb *urb) @@ -762,17 +844,17 @@ static void pl2303_read_int_callback(struct urb *urb) exit: retval = usb_submit_urb(urb, GFP_ATOMIC); - if (retval) + if (retval) { dev_err(&port->dev, "%s - usb_submit_urb failed with result %d\n", __func__, retval); + } } static void pl2303_process_read_urb(struct urb *urb) { struct usb_serial_port *port = urb->context; struct pl2303_private *priv = usb_get_serial_port_data(port); - struct tty_struct *tty; unsigned char *data = urb->transfer_buffer; char tty_flag = TTY_NORMAL; unsigned long flags; @@ -784,43 +866,41 @@ static void pl2303_process_read_urb(struct urb *urb) line_status = priv->line_status; priv->line_status &= ~UART_STATE_TRANSIENT_MASK; spin_unlock_irqrestore(&priv->lock, flags); - wake_up_interruptible(&priv->delta_msr_wait); if (!urb->actual_length) return; - tty = tty_port_tty_get(&port->port); - if (!tty) - return; - - /* break takes precedence over parity, */ - /* which takes precedence over framing errors */ + /* + * Break takes precedence over parity, which takes precedence over + * framing errors. + */ if (line_status & UART_BREAK_ERROR) tty_flag = TTY_BREAK; else if (line_status & UART_PARITY_ERROR) tty_flag = TTY_PARITY; else if (line_status & UART_FRAME_ERROR) tty_flag = TTY_FRAME; - dev_dbg(&port->dev, "%s - tty_flag = %d\n", __func__, tty_flag); + if (tty_flag != TTY_NORMAL) + dev_dbg(&port->dev, "%s - tty_flag = %d\n", __func__, + tty_flag); /* overrun is special, not associated with a char */ if (line_status & UART_OVERRUN_ERROR) - tty_insert_flip_char(tty, 0, TTY_OVERRUN); + tty_insert_flip_char(&port->port, 0, TTY_OVERRUN); if (port->port.console && port->sysrq) { for (i = 0; i < urb->actual_length; ++i) if (!usb_serial_handle_sysrq_char(port, data[i])) - tty_insert_flip_char(tty, data[i], tty_flag); + tty_insert_flip_char(&port->port, data[i], + tty_flag); } else { - tty_insert_flip_string_fixed_flag(tty, data, tty_flag, + tty_insert_flip_string_fixed_flag(&port->port, data, tty_flag, urb->actual_length); } - tty_flip_buffer_push(tty); - tty_kref_put(tty); + tty_flip_buffer_push(&port->port); } -/* All of the device info needed for the PL2303 SIO serial converter */ static struct usb_serial_driver pl2303_device = { .driver = { .owner = THIS_MODULE, @@ -832,15 +912,17 @@ static struct usb_serial_driver pl2303_device = { .bulk_out_size = 256, .open = pl2303_open, .close = pl2303_close, - .dtr_rts = pl2303_dtr_rts, + .dtr_rts = pl2303_dtr_rts, .carrier_raised = pl2303_carrier_raised, .ioctl = pl2303_ioctl, .break_ctl = pl2303_break_ctl, .set_termios = pl2303_set_termios, .tiocmget = pl2303_tiocmget, .tiocmset = pl2303_tiocmset, + .tiocmiwait = usb_serial_generic_tiocmiwait, .process_read_urb = pl2303_process_read_urb, .read_int_callback = pl2303_read_int_callback, + .probe = pl2303_probe, .attach = pl2303_startup, .release = pl2303_release, .port_probe = pl2303_port_probe, @@ -853,5 +935,5 @@ static struct usb_serial_driver * const serial_drivers[] = { module_usb_serial_driver(serial_drivers, id_table); -MODULE_DESCRIPTION(DRIVER_DESC); +MODULE_DESCRIPTION("Prolific PL2303 USB to serial adaptor driver"); MODULE_LICENSE("GPL"); diff --git a/drivers/usb/serial/pl2303.h b/drivers/usb/serial/pl2303.h index c38b8c00c06..42bc082896a 100644 --- a/drivers/usb/serial/pl2303.h +++ b/drivers/usb/serial/pl2303.h @@ -121,8 +121,11 @@ #define SUPERIAL_VENDOR_ID 0x5372 #define SUPERIAL_PRODUCT_ID 0x2303 -/* Hewlett-Packard LD220-HP POS Pole Display */ +/* Hewlett-Packard POS Pole Displays */ #define HP_VENDOR_ID 0x03f0 +#define HP_LD960_PRODUCT_ID 0x0b39 +#define HP_LCM220_PRODUCT_ID 0x3139 +#define HP_LCM960_PRODUCT_ID 0x3239 #define HP_LD220_PRODUCT_ID 0x3524 /* Cressi Edy (diving computer) PC interface */ diff --git a/drivers/usb/serial/qcaux.c b/drivers/usb/serial/qcaux.c index 9b1b96f2d09..6e9f8af9695 100644 --- a/drivers/usb/serial/qcaux.c +++ b/drivers/usb/serial/qcaux.c @@ -16,7 +16,6 @@ */ #include <linux/kernel.h> -#include <linux/init.h> #include <linux/tty.h> #include <linux/module.h> #include <linux/usb.h> @@ -54,7 +53,7 @@ #define SAMSUNG_VENDOR_ID 0x04e8 #define SAMSUNG_PRODUCT_U520 0x6640 /* SCH-U520 */ -static struct usb_device_id id_table[] = { +static const struct usb_device_id id_table[] = { { USB_DEVICE_AND_INTERFACE_INFO(UTSTARCOM_VENDOR_ID, UTSTARCOM_PRODUCT_PC5740, 0xff, 0x00, 0x00) }, { USB_DEVICE_AND_INTERFACE_INFO(UTSTARCOM_VENDOR_ID, UTSTARCOM_PRODUCT_PC5750, 0xff, 0x00, 0x00) }, { USB_DEVICE_AND_INTERFACE_INFO(UTSTARCOM_VENDOR_ID, UTSTARCOM_PRODUCT_UM150, 0xff, 0x00, 0x00) }, @@ -69,6 +68,7 @@ static struct usb_device_id id_table[] = { { USB_VENDOR_AND_INTERFACE_INFO(UTSTARCOM_VENDOR_ID, 0xff, 0xfd, 0xff) }, /* NMEA */ { USB_VENDOR_AND_INTERFACE_INFO(UTSTARCOM_VENDOR_ID, 0xff, 0xfe, 0xff) }, /* WMC */ { USB_VENDOR_AND_INTERFACE_INFO(UTSTARCOM_VENDOR_ID, 0xff, 0xff, 0xff) }, /* DIAG */ + { USB_DEVICE_AND_INTERFACE_INFO(0x1fac, 0x0151, 0xff, 0xff, 0xff) }, { }, }; MODULE_DEVICE_TABLE(usb, id_table); diff --git a/drivers/usb/serial/qcserial.c b/drivers/usb/serial/qcserial.c index aa148c21ea4..b2aa003bf41 100644 --- a/drivers/usb/serial/qcserial.c +++ b/drivers/usb/serial/qcserial.c @@ -22,8 +22,17 @@ #define DRIVER_AUTHOR "Qualcomm Inc" #define DRIVER_DESC "Qualcomm USB Serial driver" +/* standard device layouts supported by this driver */ +enum qcserial_layouts { + QCSERIAL_G2K = 0, /* Gobi 2000 */ + QCSERIAL_G1K = 1, /* Gobi 1000 */ + QCSERIAL_SWI = 2, /* Sierra Wireless */ +}; + #define DEVICE_G1K(v, p) \ - USB_DEVICE(v, p), .driver_info = 1 + USB_DEVICE(v, p), .driver_info = QCSERIAL_G1K +#define DEVICE_SWI(v, p) \ + USB_DEVICE(v, p), .driver_info = QCSERIAL_SWI static const struct usb_device_id id_table[] = { /* Gobi 1000 devices */ @@ -35,7 +44,13 @@ static const struct usb_device_id id_table[] = { {DEVICE_G1K(0x04da, 0x250c)}, /* Panasonic Gobi QDL device */ {DEVICE_G1K(0x413c, 0x8172)}, /* Dell Gobi Modem device */ {DEVICE_G1K(0x413c, 0x8171)}, /* Dell Gobi QDL device */ - {DEVICE_G1K(0x1410, 0xa001)}, /* Novatel Gobi Modem device */ + {DEVICE_G1K(0x1410, 0xa001)}, /* Novatel/Verizon USB-1000 */ + {DEVICE_G1K(0x1410, 0xa002)}, /* Novatel Gobi Modem device */ + {DEVICE_G1K(0x1410, 0xa003)}, /* Novatel Gobi Modem device */ + {DEVICE_G1K(0x1410, 0xa004)}, /* Novatel Gobi Modem device */ + {DEVICE_G1K(0x1410, 0xa005)}, /* Novatel Gobi Modem device */ + {DEVICE_G1K(0x1410, 0xa006)}, /* Novatel Gobi Modem device */ + {DEVICE_G1K(0x1410, 0xa007)}, /* Novatel Gobi Modem device */ {DEVICE_G1K(0x1410, 0xa008)}, /* Novatel Gobi QDL device */ {DEVICE_G1K(0x0b05, 0x1776)}, /* Asus Gobi Modem device */ {DEVICE_G1K(0x0b05, 0x1774)}, /* Asus Gobi QDL device */ @@ -53,6 +68,7 @@ static const struct usb_device_id id_table[] = { {DEVICE_G1K(0x05c6, 0x9221)}, /* Generic Gobi QDL device */ {DEVICE_G1K(0x05c6, 0x9231)}, /* Generic Gobi QDL device */ {DEVICE_G1K(0x1f45, 0x0001)}, /* Unknown Gobi QDL device */ + {DEVICE_G1K(0x1bc7, 0x900e)}, /* Telit Gobi QDL device */ /* Gobi 2000 devices */ {USB_DEVICE(0x1410, 0xa010)}, /* Novatel Gobi 2000 QDL device */ @@ -117,20 +133,29 @@ static const struct usb_device_id id_table[] = { {USB_DEVICE(0x1199, 0x901b)}, /* Sierra Wireless MC7770 */ {USB_DEVICE(0x12D1, 0x14F0)}, /* Sony Gobi 3000 QDL */ {USB_DEVICE(0x12D1, 0x14F1)}, /* Sony Gobi 3000 Composite */ - - /* non Gobi Qualcomm serial devices */ - {USB_DEVICE_INTERFACE_NUMBER(0x0f3d, 0x68a2, 0)}, /* Sierra Wireless MC7700 Device Management */ - {USB_DEVICE_INTERFACE_NUMBER(0x0f3d, 0x68a2, 2)}, /* Sierra Wireless MC7700 NMEA */ - {USB_DEVICE_INTERFACE_NUMBER(0x0f3d, 0x68a2, 3)}, /* Sierra Wireless MC7700 Modem */ - {USB_DEVICE_INTERFACE_NUMBER(0x114f, 0x68a2, 0)}, /* Sierra Wireless MC7750 Device Management */ - {USB_DEVICE_INTERFACE_NUMBER(0x114f, 0x68a2, 2)}, /* Sierra Wireless MC7750 NMEA */ - {USB_DEVICE_INTERFACE_NUMBER(0x114f, 0x68a2, 3)}, /* Sierra Wireless MC7750 Modem */ - {USB_DEVICE_INTERFACE_NUMBER(0x1199, 0x68a2, 0)}, /* Sierra Wireless MC7710 Device Management */ - {USB_DEVICE_INTERFACE_NUMBER(0x1199, 0x68a2, 2)}, /* Sierra Wireless MC7710 NMEA */ - {USB_DEVICE_INTERFACE_NUMBER(0x1199, 0x68a2, 3)}, /* Sierra Wireless MC7710 Modem */ - {USB_DEVICE_INTERFACE_NUMBER(0x1199, 0x901c, 0)}, /* Sierra Wireless EM7700 Device Management */ - {USB_DEVICE_INTERFACE_NUMBER(0x1199, 0x901c, 2)}, /* Sierra Wireless EM7700 NMEA */ - {USB_DEVICE_INTERFACE_NUMBER(0x1199, 0x901c, 3)}, /* Sierra Wireless EM7700 Modem */ + {USB_DEVICE(0x0AF0, 0x8120)}, /* Option GTM681W */ + + /* non-Gobi Sierra Wireless devices */ + {DEVICE_SWI(0x0f3d, 0x68a2)}, /* Sierra Wireless MC7700 */ + {DEVICE_SWI(0x114f, 0x68a2)}, /* Sierra Wireless MC7750 */ + {DEVICE_SWI(0x1199, 0x68a2)}, /* Sierra Wireless MC7710 */ + {DEVICE_SWI(0x1199, 0x68c0)}, /* Sierra Wireless MC73xx */ + {DEVICE_SWI(0x1199, 0x901c)}, /* Sierra Wireless EM7700 */ + {DEVICE_SWI(0x1199, 0x901f)}, /* Sierra Wireless EM7355 */ + {DEVICE_SWI(0x1199, 0x9040)}, /* Sierra Wireless Modem */ + {DEVICE_SWI(0x1199, 0x9041)}, /* Sierra Wireless MC7305/MC7355 */ + {DEVICE_SWI(0x1199, 0x9051)}, /* Netgear AirCard 340U */ + {DEVICE_SWI(0x1199, 0x9053)}, /* Sierra Wireless Modem */ + {DEVICE_SWI(0x1199, 0x9054)}, /* Sierra Wireless Modem */ + {DEVICE_SWI(0x1199, 0x9055)}, /* Netgear AirCard 341U */ + {DEVICE_SWI(0x1199, 0x9056)}, /* Sierra Wireless Modem */ + {DEVICE_SWI(0x1199, 0x9060)}, /* Sierra Wireless Modem */ + {DEVICE_SWI(0x1199, 0x9061)}, /* Sierra Wireless Modem */ + {DEVICE_SWI(0x413c, 0x81a2)}, /* Dell Wireless 5806 Gobi(TM) 4G LTE Mobile Broadband Card */ + {DEVICE_SWI(0x413c, 0x81a3)}, /* Dell Wireless 5570 HSPA+ (42Mbps) Mobile Broadband Card */ + {DEVICE_SWI(0x413c, 0x81a4)}, /* Dell Wireless 5570e HSPA+ (42Mbps) Mobile Broadband Card */ + {DEVICE_SWI(0x413c, 0x81a8)}, /* Dell Wireless 5808 Gobi(TM) 4G LTE Mobile Broadband Card */ + {DEVICE_SWI(0x413c, 0x81a9)}, /* Dell Wireless 5808e Gobi(TM) 4G LTE Mobile Broadband Card */ { } /* Terminating entry */ }; @@ -143,11 +168,8 @@ static int qcprobe(struct usb_serial *serial, const struct usb_device_id *id) int retval = -ENODEV; __u8 nintf; __u8 ifnum; - bool is_gobi1k = id->driver_info ? true : false; int altsetting = -1; - dev_dbg(dev, "Is Gobi 1000 = %d\n", is_gobi1k); - nintf = serial->dev->actconfig->desc.bNumInterfaces; dev_dbg(dev, "Num Interfaces = %d\n", nintf); ifnum = intf->desc.bInterfaceNumber; @@ -175,43 +197,51 @@ static int qcprobe(struct usb_serial *serial, const struct usb_device_id *id) } - /* allow any number of interfaces when doing direct interface match */ - if (id->match_flags & USB_DEVICE_ID_MATCH_INT_NUMBER) { - dev_dbg(dev, "Generic Qualcomm serial interface found\n"); - altsetting = 0; - goto done; - } - - if (nintf < 3 || nintf > 4) { - dev_err(dev, "unknown number of interfaces: %d\n", nintf); - goto done; - } - /* default to enabling interface */ altsetting = 0; - /* Composite mode; don't bind to the QMI/net interface as that + /* + * Composite mode; don't bind to the QMI/net interface as that * gets handled by other drivers. */ - if (is_gobi1k) { - /* Gobi 1K USB layout: - * 0: serial port (doesn't respond) + switch (id->driver_info) { + case QCSERIAL_G1K: + /* + * Gobi 1K USB layout: + * 0: DM/DIAG (use libqcdm from ModemManager for communication) * 1: serial port (doesn't respond) * 2: AT-capable modem port * 3: QMI/net */ - if (ifnum == 2) + if (nintf < 3 || nintf > 4) { + dev_err(dev, "unknown number of interfaces: %d\n", nintf); + altsetting = -1; + goto done; + } + + if (ifnum == 0) { + dev_dbg(dev, "Gobi 1K DM/DIAG interface found\n"); + altsetting = 1; + } else if (ifnum == 2) dev_dbg(dev, "Modem port found\n"); else altsetting = -1; - } else { - /* Gobi 2K+ USB layout: + break; + case QCSERIAL_G2K: + /* + * Gobi 2K+ USB layout: * 0: QMI/net * 1: DM/DIAG (use libqcdm from ModemManager for communication) * 2: AT-capable modem port * 3: NMEA */ + if (nintf < 3 || nintf > 4) { + dev_err(dev, "unknown number of interfaces: %d\n", nintf); + altsetting = -1; + goto done; + } + switch (ifnum) { case 0: /* Don't claim the QMI/net interface */ @@ -232,6 +262,35 @@ static int qcprobe(struct usb_serial *serial, const struct usb_device_id *id) dev_dbg(dev, "Gobi 2K+ NMEA GPS interface found\n"); break; } + break; + case QCSERIAL_SWI: + /* + * Sierra Wireless layout: + * 0: DM/DIAG (use libqcdm from ModemManager for communication) + * 2: NMEA + * 3: AT-capable modem port + * 8: QMI/net + */ + switch (ifnum) { + case 0: + dev_dbg(dev, "DM/DIAG interface found\n"); + break; + case 2: + dev_dbg(dev, "NMEA GPS interface found\n"); + break; + case 3: + dev_dbg(dev, "Modem port found\n"); + break; + default: + /* don't claim any unsupported interface */ + altsetting = -1; + break; + } + break; + default: + dev_err(dev, "unsupported device layout type: %lu\n", + id->driver_info); + break; } done: diff --git a/drivers/usb/serial/quatech2.c b/drivers/usb/serial/quatech2.c index d152be97d04..504f5bff79c 100644 --- a/drivers/usb/serial/quatech2.c +++ b/drivers/usb/serial/quatech2.c @@ -15,7 +15,6 @@ #include <asm/unaligned.h> #include <linux/errno.h> -#include <linux/init.h> #include <linux/slab.h> #include <linux/tty.h> #include <linux/tty_driver.h> @@ -62,6 +61,7 @@ #define MAX_BAUD_RATE 921600 #define DEFAULT_BAUD_RATE 9600 +#define QT2_READ_BUFFER_SIZE 512 /* size of read buffer */ #define QT2_WRITE_BUFFER_SIZE 512 /* size of write buffer */ #define QT2_WRITE_CONTROL_SIZE 5 /* control bytes used for a write */ @@ -112,25 +112,21 @@ struct qt2_serial_private { unsigned char current_port; /* current port for incoming data */ struct urb *read_urb; /* shared among all ports */ - char read_buffer[512]; + char *read_buffer; }; struct qt2_port_private { - bool is_open; u8 device_port; spinlock_t urb_lock; bool urb_in_use; struct urb *write_urb; - char write_buffer[QT2_WRITE_BUFFER_SIZE]; + char *write_buffer; spinlock_t lock; u8 shadowLSR; u8 shadowMSR; - wait_queue_head_t delta_msr_wait; /* Used for TIOCMIWAIT */ - struct async_icount icount; - struct usb_serial_port *port; }; @@ -146,6 +142,7 @@ static void qt2_release(struct usb_serial *serial) serial_priv = usb_get_serial_data(serial); usb_free_urb(serial_priv->read_urb); + kfree(serial_priv->read_buffer); kfree(serial_priv); } @@ -347,7 +344,7 @@ static int qt2_open(struct tty_struct *tty, struct usb_serial_port *port) int status; unsigned long flags; - device_port = (u16) (port->number - port->serial->minor); + device_port = port->port_number; serial = port->serial; @@ -375,7 +372,7 @@ static int qt2_open(struct tty_struct *tty, struct usb_serial_port *port) device_port, data, 2, QT2_USB_TIMEOUT); if (status < 0) { - dev_err(&port->dev, "%s - open port failed %i", __func__, + dev_err(&port->dev, "%s - open port failed %i\n", __func__, status); kfree(data); return status; @@ -392,13 +389,11 @@ static int qt2_open(struct tty_struct *tty, struct usb_serial_port *port) status = qt2_set_port_config(serial->dev, device_port, DEFAULT_BAUD_RATE, UART_LCR_WLEN8); if (status < 0) { - dev_err(&port->dev, - "%s - initial setup failed for port %i (%i)\n", - __func__, port->number, device_port); + dev_err(&port->dev, "%s - initial setup failed (%i)\n", + __func__, device_port); return status; } - port_priv->is_open = true; port_priv->device_port = (u8) device_port; if (tty) @@ -418,19 +413,11 @@ static void qt2_close(struct usb_serial_port *port) serial = port->serial; port_priv = usb_get_serial_port_data(port); - port_priv->is_open = false; - spin_lock_irqsave(&port_priv->urb_lock, flags); usb_kill_urb(port_priv->write_urb); port_priv->urb_in_use = false; spin_unlock_irqrestore(&port_priv->urb_lock, flags); - mutex_lock(&port->serial->disc_mutex); - if (port->serial->disconnected) { - mutex_unlock(&port->serial->disc_mutex); - return; - } - /* flush the port transmit buffer */ i = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0), @@ -461,8 +448,6 @@ static void qt2_close(struct usb_serial_port *port) if (i < 0) dev_err(&port->dev, "%s - close port failed %i\n", __func__, i); - - mutex_unlock(&port->serial->disc_mutex); } static void qt2_disconnect(struct usb_serial *serial) @@ -481,7 +466,7 @@ static int get_serial_info(struct usb_serial_port *port, return -EFAULT; memset(&tmp, 0, sizeof(tmp)); - tmp.line = port->serial->minor; + tmp.line = port->minor; tmp.port = 0; tmp.irq = 0; tmp.flags = ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ; @@ -495,67 +480,6 @@ static int get_serial_info(struct usb_serial_port *port, return 0; } -static int wait_modem_info(struct usb_serial_port *port, unsigned int arg) -{ - struct qt2_port_private *priv = usb_get_serial_port_data(port); - struct async_icount prev, cur; - unsigned long flags; - - spin_lock_irqsave(&priv->lock, flags); - prev = priv->icount; - spin_unlock_irqrestore(&priv->lock, flags); - - while (1) { - wait_event_interruptible(priv->delta_msr_wait, - ((priv->icount.rng != prev.rng) || - (priv->icount.dsr != prev.dsr) || - (priv->icount.dcd != prev.dcd) || - (priv->icount.cts != prev.cts))); - - if (signal_pending(current)) - return -ERESTARTSYS; - - spin_lock_irqsave(&priv->lock, flags); - cur = priv->icount; - spin_unlock_irqrestore(&priv->lock, flags); - - if ((prev.rng == cur.rng) && - (prev.dsr == cur.dsr) && - (prev.dcd == cur.dcd) && - (prev.cts == cur.cts)) - return -EIO; - - if ((arg & TIOCM_RNG && (prev.rng != cur.rng)) || - (arg & TIOCM_DSR && (prev.dsr != cur.dsr)) || - (arg & TIOCM_CD && (prev.dcd != cur.dcd)) || - (arg & TIOCM_CTS && (prev.cts != cur.cts))) - return 0; - } - return 0; -} - -static int qt2_get_icount(struct tty_struct *tty, - struct serial_icounter_struct *icount) -{ - struct usb_serial_port *port = tty->driver_data; - struct qt2_port_private *priv = usb_get_serial_port_data(port); - struct async_icount cnow = priv->icount; - - icount->cts = cnow.cts; - icount->dsr = cnow.dsr; - icount->rng = cnow.rng; - icount->dcd = cnow.dcd; - icount->rx = cnow.rx; - icount->tx = cnow.tx; - icount->frame = cnow.frame; - icount->overrun = cnow.overrun; - icount->parity = cnow.parity; - icount->brk = cnow.brk; - icount->buf_overrun = cnow.buf_overrun; - - return 0; -} - static int qt2_ioctl(struct tty_struct *tty, unsigned int cmd, unsigned long arg) { @@ -565,10 +489,6 @@ static int qt2_ioctl(struct tty_struct *tty, case TIOCGSERIAL: return get_serial_info(port, (struct serial_struct __user *)arg); - - case TIOCMIWAIT: - return wait_modem_info(port, arg); - default: break; } @@ -603,13 +523,12 @@ static void qt2_process_flush(struct usb_serial_port *port, unsigned char *ch) return; } -void qt2_process_read_urb(struct urb *urb) +static void qt2_process_read_urb(struct urb *urb) { struct usb_serial *serial; struct qt2_serial_private *serial_priv; struct usb_serial_port *port; struct qt2_port_private *port_priv; - struct tty_struct *tty; bool escapeflag; unsigned char *ch; int i; @@ -620,15 +539,11 @@ void qt2_process_read_urb(struct urb *urb) return; ch = urb->transfer_buffer; - tty = NULL; serial = urb->context; serial_priv = usb_get_serial_data(serial); port = serial->port[serial_priv->current_port]; port_priv = usb_get_serial_port_data(port); - if (port_priv->is_open) - tty = tty_port_tty_get(&port->port); - for (i = 0; i < urb->actual_length; i++) { ch = (unsigned char *)urb->transfer_buffer + i; if ((i <= (len - 3)) && @@ -666,10 +581,7 @@ void qt2_process_read_urb(struct urb *urb) __func__); break; } - if (tty) { - tty_flip_buffer_push(tty); - tty_kref_put(tty); - } + tty_flip_buffer_push(&port->port); newport = *(ch + 3); @@ -683,10 +595,6 @@ void qt2_process_read_urb(struct urb *urb) serial_priv->current_port = newport; port = serial->port[serial_priv->current_port]; port_priv = usb_get_serial_port_data(port); - if (port_priv->is_open) - tty = tty_port_tty_get(&port->port); - else - tty = NULL; i += 3; escapeflag = true; break; @@ -697,8 +605,8 @@ void qt2_process_read_urb(struct urb *urb) escapeflag = true; break; case QT2_CONTROL_ESCAPE: - tty_buffer_request_room(tty, 2); - tty_insert_flip_string(tty, ch, 2); + tty_buffer_request_room(&port->port, 2); + tty_insert_flip_string(&port->port, ch, 2); i += 2; escapeflag = true; break; @@ -712,16 +620,11 @@ void qt2_process_read_urb(struct urb *urb) continue; } - if (tty) { - tty_buffer_request_room(tty, 1); - tty_insert_flip_string(tty, ch, 1); - } + tty_buffer_request_room(&port->port, 1); + tty_insert_flip_string(&port->port, ch, 1); } - if (tty) { - tty_flip_buffer_push(tty); - tty_kref_put(tty); - } + tty_flip_buffer_push(&port->port); } static void qt2_write_bulk_callback(struct urb *urb) @@ -772,16 +675,14 @@ static int qt2_setup_urbs(struct usb_serial *serial) serial_priv = usb_get_serial_data(serial); serial_priv->read_urb = usb_alloc_urb(0, GFP_KERNEL); - if (!serial_priv->read_urb) { - dev_err(&serial->dev->dev, "No free urbs available\n"); + if (!serial_priv->read_urb) return -ENOMEM; - } usb_fill_bulk_urb(serial_priv->read_urb, serial->dev, usb_rcvbulkpipe(serial->dev, port0->bulk_in_endpointAddress), serial_priv->read_buffer, - sizeof(serial_priv->read_buffer), + QT2_READ_BUFFER_SIZE, qt2_read_bulk_callback, serial); status = usb_submit_urb(serial_priv->read_urb, GFP_KERNEL); @@ -811,9 +712,13 @@ static int qt2_attach(struct usb_serial *serial) } serial_priv = kzalloc(sizeof(*serial_priv), GFP_KERNEL); - if (!serial_priv) { - dev_err(&serial->dev->dev, "%s - Out of memory\n", __func__); + if (!serial_priv) return -ENOMEM; + + serial_priv->read_buffer = kmalloc(QT2_READ_BUFFER_SIZE, GFP_KERNEL); + if (!serial_priv->read_buffer) { + status = -ENOMEM; + goto err_buf; } usb_set_serial_data(serial, serial_priv); @@ -825,6 +730,8 @@ static int qt2_attach(struct usb_serial *serial) return 0; attach_failed: + kfree(serial_priv->read_buffer); +err_buf: kfree(serial_priv); return status; } @@ -841,24 +748,31 @@ static int qt2_port_probe(struct usb_serial_port *port) spin_lock_init(&port_priv->lock); spin_lock_init(&port_priv->urb_lock); - init_waitqueue_head(&port_priv->delta_msr_wait); port_priv->port = port; + port_priv->write_buffer = kmalloc(QT2_WRITE_BUFFER_SIZE, GFP_KERNEL); + if (!port_priv->write_buffer) + goto err_buf; + port_priv->write_urb = usb_alloc_urb(0, GFP_KERNEL); - if (!port_priv->write_urb) { - kfree(port_priv); - return -ENOMEM; - } + if (!port_priv->write_urb) + goto err_urb; + bEndpointAddress = serial->port[0]->bulk_out_endpointAddress; usb_fill_bulk_urb(port_priv->write_urb, serial->dev, usb_sndbulkpipe(serial->dev, bEndpointAddress), port_priv->write_buffer, - sizeof(port_priv->write_buffer), + QT2_WRITE_BUFFER_SIZE, qt2_write_bulk_callback, port); usb_set_serial_port_data(port, port_priv); return 0; +err_urb: + kfree(port_priv->write_buffer); +err_buf: + kfree(port_priv); + return -ENOMEM; } static int qt2_port_remove(struct usb_serial_port *port) @@ -867,6 +781,7 @@ static int qt2_port_remove(struct usb_serial_port *port) port_priv = usb_get_serial_port_data(port); usb_free_urb(port_priv->write_urb); + kfree(port_priv->write_buffer); kfree(port_priv); return 0; @@ -922,12 +837,6 @@ static void qt2_break_ctl(struct tty_struct *tty, int break_state) port_priv = usb_get_serial_port_data(port); - if (!port_priv->is_open) { - dev_err(&port->dev, - "%s - port is not open\n", __func__); - return; - } - val = (break_state == -1) ? 1 : 0; status = qt2_control_msg(port->serial->dev, QT2_BREAK_CONTROL, @@ -945,19 +854,17 @@ static void qt2_dtr_rts(struct usb_serial_port *port, int on) struct usb_device *dev = port->serial->dev; struct qt2_port_private *port_priv = usb_get_serial_port_data(port); - mutex_lock(&port->serial->disc_mutex); - if (!port->serial->disconnected) { - /* Disable flow control */ - if (!on && qt2_setregister(dev, port_priv->device_port, + /* Disable flow control */ + if (!on) { + if (qt2_setregister(dev, port_priv->device_port, UART_MCR, 0) < 0) dev_warn(&port->dev, "error from flowcontrol urb\n"); - /* drop RTS and DTR */ - if (on) - update_mctrl(port_priv, TIOCM_DTR | TIOCM_RTS, 0); - else - update_mctrl(port_priv, 0, TIOCM_DTR | TIOCM_RTS); } - mutex_unlock(&port->serial->disc_mutex); + /* drop RTS and DTR */ + if (on) + update_mctrl(port_priv, TIOCM_DTR | TIOCM_RTS, 0); + else + update_mctrl(port_priv, 0, TIOCM_DTR | TIOCM_RTS); } static void qt2_update_msr(struct usb_serial_port *port, unsigned char *ch) @@ -975,18 +882,15 @@ static void qt2_update_msr(struct usb_serial_port *port, unsigned char *ch) if (newMSR & UART_MSR_ANY_DELTA) { /* update input line counters */ if (newMSR & UART_MSR_DCTS) - port_priv->icount.cts++; - + port->icount.cts++; if (newMSR & UART_MSR_DDSR) - port_priv->icount.dsr++; - + port->icount.dsr++; if (newMSR & UART_MSR_DDCD) - port_priv->icount.dcd++; - + port->icount.dcd++; if (newMSR & UART_MSR_TERI) - port_priv->icount.rng++; + port->icount.rng++; - wake_up_interruptible(&port_priv->delta_msr_wait); + wake_up_interruptible(&port->port.delta_msr_wait); } } @@ -1006,7 +910,7 @@ static void qt2_update_lsr(struct usb_serial_port *port, unsigned char *ch) port_priv->shadowLSR = newLSR; spin_unlock_irqrestore(&port_priv->lock, flags); - icount = &port_priv->icount; + icount = &port->icount; if (newLSR & UART_LSR_BRK_ERROR_BITS) { @@ -1116,7 +1020,8 @@ static struct usb_serial_driver qt2_device = { .break_ctl = qt2_break_ctl, .tiocmget = qt2_tiocmget, .tiocmset = qt2_tiocmset, - .get_icount = qt2_get_icount, + .tiocmiwait = usb_serial_generic_tiocmiwait, + .get_icount = usb_serial_generic_get_icount, .ioctl = qt2_ioctl, .set_termios = qt2_set_termios, }; diff --git a/drivers/usb/serial/safe_serial.c b/drivers/usb/serial/safe_serial.c index c949ce6ef0c..b2dff0f1474 100644 --- a/drivers/usb/serial/safe_serial.c +++ b/drivers/usb/serial/safe_serial.c @@ -67,7 +67,6 @@ #include <linux/kernel.h> #include <linux/errno.h> #include <linux/gfp.h> -#include <linux/init.h> #include <linux/tty.h> #include <linux/tty_driver.h> #include <linux/tty_flip.h> @@ -92,13 +91,6 @@ MODULE_AUTHOR(DRIVER_AUTHOR); MODULE_DESCRIPTION(DRIVER_DESC); MODULE_LICENSE("GPL"); -static __u16 vendor; /* no default */ -static __u16 product; /* no default */ -module_param(vendor, ushort, 0); -MODULE_PARM_DESC(vendor, "User specified USB idVendor (required)"); -module_param(product, ushort, 0); -MODULE_PARM_DESC(product, "User specified USB idProduct (required)"); - module_param(safe, bool, 0); MODULE_PARM_DESC(safe, "Turn Safe Encapsulation On/Off"); @@ -132,7 +124,7 @@ MODULE_PARM_DESC(padded, "Pad to full wMaxPacketSize On/Off"); .bInterfaceClass = (ic), \ .bInterfaceSubClass = (isc), -static struct usb_device_id id_table[] = { +static const struct usb_device_id id_table[] = { {MY_USB_DEVICE(0x49f, 0xffff, CDC_DEVICE_CLASS, LINEO_INTERFACE_CLASS, LINEO_INTERFACE_SUBCLASS_SAFESERIAL)}, /* Itsy */ {MY_USB_DEVICE(0x3f0, 0x2101, CDC_DEVICE_CLASS, LINEO_INTERFACE_CLASS, LINEO_INTERFACE_SUBCLASS_SAFESERIAL)}, /* Calypso */ {MY_USB_DEVICE(0x4dd, 0x8001, CDC_DEVICE_CLASS, LINEO_INTERFACE_CLASS, LINEO_INTERFACE_SUBCLASS_SAFESERIAL)}, /* Iris */ @@ -140,8 +132,6 @@ static struct usb_device_id id_table[] = { {MY_USB_DEVICE(0x4dd, 0x8003, CDC_DEVICE_CLASS, LINEO_INTERFACE_CLASS, LINEO_INTERFACE_SUBCLASS_SAFESERIAL)}, /* Collie */ {MY_USB_DEVICE(0x4dd, 0x8004, CDC_DEVICE_CLASS, LINEO_INTERFACE_CLASS, LINEO_INTERFACE_SUBCLASS_SAFESERIAL)}, /* Collie */ {MY_USB_DEVICE(0x5f9, 0xffff, CDC_DEVICE_CLASS, LINEO_INTERFACE_CLASS, LINEO_INTERFACE_SUBCLASS_SAFESERIAL)}, /* Sharp tmp */ - /* extra null entry for module vendor/produc parameters */ - {MY_USB_DEVICE(0, 0, CDC_DEVICE_CLASS, LINEO_INTERFACE_CLASS, LINEO_INTERFACE_SUBCLASS_SAFESERIAL)}, {} /* terminating entry */ }; @@ -207,38 +197,31 @@ static void safe_process_read_urb(struct urb *urb) unsigned char *data = urb->transfer_buffer; unsigned char length = urb->actual_length; int actual_length; - struct tty_struct *tty; __u16 fcs; if (!length) return; - tty = tty_port_tty_get(&port->port); - if (!tty) - return; - if (!safe) goto out; fcs = fcs_compute10(data, length, CRC10_INITFCS); if (fcs) { dev_err(&port->dev, "%s - bad CRC %x\n", __func__, fcs); - goto err; + return; } actual_length = data[length - 2] >> 2; if (actual_length > (length - 2)) { dev_err(&port->dev, "%s - inconsistent lengths %d:%d\n", __func__, actual_length, length); - goto err; + return; } dev_info(&urb->dev->dev, "%s - actual: %d\n", __func__, actual_length); length = actual_length; out: - tty_insert_flip_string(tty, data, length); - tty_flip_buffer_push(tty); -err: - tty_kref_put(tty); + tty_insert_flip_string(&port->port, data, length); + tty_flip_buffer_push(&port->port); } static int safe_prepare_write_buffer(struct usb_serial_port *port, @@ -279,7 +262,19 @@ static int safe_prepare_write_buffer(struct usb_serial_port *port, static int safe_startup(struct usb_serial *serial) { - switch (serial->interface->cur_altsetting->desc.bInterfaceProtocol) { + struct usb_interface_descriptor *desc; + + if (serial->dev->descriptor.bDeviceClass != CDC_DEVICE_CLASS) + return -ENODEV; + + desc = &serial->interface->cur_altsetting->desc; + + if (desc->bInterfaceClass != LINEO_INTERFACE_CLASS) + return -ENODEV; + if (desc->bInterfaceSubClass != LINEO_INTERFACE_SUBCLASS_SAFESERIAL) + return -ENODEV; + + switch (desc->bInterfaceProtocol) { case LINEO_SAFESERIAL_CRC: break; case LINEO_SAFESERIAL_CRC_PADDED: @@ -307,30 +302,4 @@ static struct usb_serial_driver * const serial_drivers[] = { &safe_device, NULL }; -static int __init safe_init(void) -{ - int i; - - /* if we have vendor / product parameters patch them into id list */ - if (vendor || product) { - pr_info("vendor: %x product: %x\n", vendor, product); - - for (i = 0; i < ARRAY_SIZE(id_table); i++) { - if (!id_table[i].idVendor && !id_table[i].idProduct) { - id_table[i].idVendor = vendor; - id_table[i].idProduct = product; - break; - } - } - } - - return usb_serial_register_drivers(serial_drivers, KBUILD_MODNAME, id_table); -} - -static void __exit safe_exit(void) -{ - usb_serial_deregister_drivers(serial_drivers); -} - -module_init(safe_init); -module_exit(safe_exit); +module_usb_serial_driver(serial_drivers, id_table); diff --git a/drivers/usb/serial/siemens_mpi.c b/drivers/usb/serial/siemens_mpi.c deleted file mode 100644 index a76b1ae54a2..00000000000 --- a/drivers/usb/serial/siemens_mpi.c +++ /dev/null @@ -1,47 +0,0 @@ -/* - * Siemens USB-MPI Serial USB driver - * - * Copyright (C) 2005 Thomas Hergenhahn <thomas.hergenhahn@suse.de> - * Copyright (C) 2005,2008 Greg Kroah-Hartman <gregkh@suse.de> - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License version - * 2 as published by the Free Software Foundation. - */ - -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/tty.h> -#include <linux/module.h> -#include <linux/usb.h> -#include <linux/usb/serial.h> - -#define DRIVER_AUTHOR "Thomas Hergenhahn@web.de http://libnodave.sf.net" -#define DRIVER_DESC "Driver for Siemens USB/MPI adapter" - - -static const struct usb_device_id id_table[] = { - /* Vendor and product id for 6ES7-972-0CB20-0XA0 */ - { USB_DEVICE(0x908, 0x0004) }, - { }, -}; -MODULE_DEVICE_TABLE(usb, id_table); - -static struct usb_serial_driver siemens_usb_mpi_device = { - .driver = { - .owner = THIS_MODULE, - .name = "siemens_mpi", - }, - .id_table = id_table, - .num_ports = 1, -}; - -static struct usb_serial_driver * const serial_drivers[] = { - &siemens_usb_mpi_device, NULL -}; - -module_usb_serial_driver(serial_drivers, id_table); - -MODULE_AUTHOR(DRIVER_AUTHOR); -MODULE_DESCRIPTION(DRIVER_DESC); -MODULE_LICENSE("GPL"); diff --git a/drivers/usb/serial/sierra.c b/drivers/usb/serial/sierra.c index af06f2f5f38..6f7f01eb556 100644 --- a/drivers/usb/serial/sierra.c +++ b/drivers/usb/serial/sierra.c @@ -58,6 +58,7 @@ struct sierra_intf_private { spinlock_t susp_lock; unsigned int suspended:1; int in_flight; + unsigned int open_ports; }; static int sierra_set_power_state(struct usb_device *udev, __u16 swiState) @@ -291,7 +292,6 @@ static const struct usb_device_id id_table[] = { { USB_DEVICE(0x0f3d, 0x68A3), /* Airprime/Sierra Wireless Direct IP modems */ .driver_info = (kernel_ulong_t)&direct_ip_interface_blacklist }, - { USB_DEVICE(0x413C, 0x08133) }, /* Dell Computer Corp. Wireless 5720 VZW Mobile Broadband (EVDO Rev-A) Minicard GPS Port */ { } }; @@ -316,7 +316,6 @@ struct sierra_port_private { int dsr_state; int dcd_state; int ri_state; - unsigned int opened:1; }; static int sierra_send_setup(struct usb_serial_port *port) @@ -365,20 +364,13 @@ static int sierra_send_setup(struct usb_serial_port *port) if (retval < 0) return retval; - retval = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0), + retval = usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0), 0x22, 0x21, val, interface, NULL, 0, USB_CTRL_SET_TIMEOUT); usb_autopm_put_interface(serial->interface); return retval; } -static void sierra_set_termios(struct tty_struct *tty, - struct usb_serial_port *port, struct ktermios *old_termios) -{ - tty_termios_copy_hw(&tty->termios, old_termios); - sierra_send_setup(port); -} - static int sierra_tiocmget(struct tty_struct *tty) { struct usb_serial_port *port = tty->driver_data; @@ -419,9 +411,7 @@ static int sierra_tiocmset(struct tty_struct *tty, static void sierra_release_urb(struct urb *urb) { - struct usb_serial_port *port; if (urb) { - port = urb->context; kfree(urb->transfer_buffer); usb_free_urb(urb); } @@ -434,7 +424,7 @@ static void sierra_outdat_callback(struct urb *urb) struct sierra_intf_private *intfdata; int status = urb->status; - intfdata = port->serial->private; + intfdata = usb_get_serial_data(port->serial); /* free up the transfer buffer, as usb_free_urb() does not do this */ kfree(urb->transfer_buffer); @@ -471,7 +461,7 @@ static int sierra_write(struct tty_struct *tty, struct usb_serial_port *port, return 0; portdata = usb_get_serial_port_data(port); - intfdata = serial->private; + intfdata = usb_get_serial_data(serial); dev_dbg(&port->dev, "%s: write (%zd bytes)\n", __func__, writesize); spin_lock_irqsave(&portdata->lock, flags); @@ -497,14 +487,12 @@ static int sierra_write(struct tty_struct *tty, struct usb_serial_port *port, buffer = kmalloc(writesize, GFP_ATOMIC); if (!buffer) { - dev_err(&port->dev, "out of memory\n"); retval = -ENOMEM; goto error_no_buffer; } urb = usb_alloc_urb(0, GFP_ATOMIC); if (!urb) { - dev_err(&port->dev, "no more free urbs\n"); retval = -ENOMEM; goto error_no_urb; } @@ -569,7 +557,6 @@ static void sierra_indat_callback(struct urb *urb) int err; int endpoint; struct usb_serial_port *port; - struct tty_struct *tty; unsigned char *data = urb->transfer_buffer; int status = urb->status; @@ -581,16 +568,12 @@ static void sierra_indat_callback(struct urb *urb) " endpoint %02x\n", __func__, status, endpoint); } else { if (urb->actual_length) { - tty = tty_port_tty_get(&port->port); - if (tty) { - tty_insert_flip_string(tty, data, - urb->actual_length); - tty_flip_buffer_push(tty); - - tty_kref_put(tty); - usb_serial_debug_data(&port->dev, __func__, - urb->actual_length, data); - } + tty_insert_flip_string(&port->port, data, + urb->actual_length); + tty_flip_buffer_push(&port->port); + + usb_serial_debug_data(&port->dev, __func__, + urb->actual_length, data); } else { dev_dbg(&port->dev, "%s: empty read urb" " received\n", __func__); @@ -633,7 +616,6 @@ static void sierra_instat_callback(struct urb *urb) unsigned char signals = *((unsigned char *) urb->transfer_buffer + sizeof(struct usb_ctrlrequest)); - struct tty_struct *tty; dev_dbg(&port->dev, "%s: signal x%x\n", __func__, signals); @@ -644,11 +626,8 @@ static void sierra_instat_callback(struct urb *urb) portdata->dsr_state = ((signals & 0x02) ? 1 : 0); portdata->ri_state = ((signals & 0x08) ? 1 : 0); - tty = tty_port_tty_get(&port->port); - if (tty && !C_CLOCAL(tty) && - old_dcd_state && !portdata->dcd_state) - tty_hangup(tty); - tty_kref_put(tty); + if (old_dcd_state && !portdata->dcd_state) + tty_port_tty_hangup(&port->port, true); } else { dev_dbg(&port->dev, "%s: type %x req %x\n", __func__, req_pkt->bRequestType, @@ -686,6 +665,23 @@ static int sierra_write_room(struct tty_struct *tty) return 2048; } +static int sierra_chars_in_buffer(struct tty_struct *tty) +{ + struct usb_serial_port *port = tty->driver_data; + struct sierra_port_private *portdata = usb_get_serial_port_data(port); + unsigned long flags; + int chars; + + /* NOTE: This overcounts somewhat. */ + spin_lock_irqsave(&portdata->lock, flags); + chars = portdata->outstanding_urbs * MAX_TRANSFER; + spin_unlock_irqrestore(&portdata->lock, flags); + + dev_dbg(&port->dev, "%s - %d\n", __func__, chars); + + return chars; +} + static void sierra_stop_rx_urbs(struct usb_serial_port *port) { int i; @@ -741,15 +737,9 @@ static struct urb *sierra_setup_urb(struct usb_serial *serial, int endpoint, struct urb *urb; u8 *buf; - if (endpoint == -1) - return NULL; - urb = usb_alloc_urb(0, mem_flags); - if (urb == NULL) { - dev_dbg(&serial->dev->dev, "%s: alloc for endpoint %d failed\n", - __func__, endpoint); + if (!urb) return NULL; - } buf = kmalloc(len, mem_flags); if (buf) { @@ -761,9 +751,6 @@ static struct urb *sierra_setup_urb(struct usb_serial *serial, int endpoint, dev_dbg(&serial->dev->dev, "%s %c u : %p d:%p\n", __func__, dir == USB_DIR_IN ? 'i' : 'o', urb, buf); } else { - dev_dbg(&serial->dev->dev, "%s %c u:%p d:%p\n", __func__, - dir == USB_DIR_IN ? 'i' : 'o', urb, buf); - sierra_release_urb(urb); urb = NULL; } @@ -776,45 +763,48 @@ static void sierra_close(struct usb_serial_port *port) int i; struct usb_serial *serial = port->serial; struct sierra_port_private *portdata; - struct sierra_intf_private *intfdata = port->serial->private; + struct sierra_intf_private *intfdata = usb_get_serial_data(serial); + struct urb *urb; portdata = usb_get_serial_port_data(port); - portdata->rts_state = 0; - portdata->dtr_state = 0; - - if (serial->dev) { - mutex_lock(&serial->disc_mutex); - if (!serial->disconnected) { - serial->interface->needs_remote_wakeup = 0; - /* odd error handling due to pm counters */ - if (!usb_autopm_get_interface(serial->interface)) - sierra_send_setup(port); - else - usb_autopm_get_interface_no_resume(serial->interface); - - } - mutex_unlock(&serial->disc_mutex); - spin_lock_irq(&intfdata->susp_lock); - portdata->opened = 0; - spin_unlock_irq(&intfdata->susp_lock); + /* + * Need to take susp_lock to make sure port is not already being + * resumed, but no need to hold it due to ASYNC_INITIALIZED. + */ + spin_lock_irq(&intfdata->susp_lock); + if (--intfdata->open_ports == 0) + serial->interface->needs_remote_wakeup = 0; + spin_unlock_irq(&intfdata->susp_lock); + + for (;;) { + urb = usb_get_from_anchor(&portdata->delayed); + if (!urb) + break; + kfree(urb->transfer_buffer); + usb_free_urb(urb); + usb_autopm_put_interface_async(serial->interface); + spin_lock(&portdata->lock); + portdata->outstanding_urbs--; + spin_unlock(&portdata->lock); + } + sierra_stop_rx_urbs(port); + usb_kill_anchored_urbs(&portdata->active); - /* Stop reading urbs */ - sierra_stop_rx_urbs(port); - /* .. and release them */ - for (i = 0; i < portdata->num_in_urbs; i++) { - sierra_release_urb(portdata->in_urbs[i]); - portdata->in_urbs[i] = NULL; - } + for (i = 0; i < portdata->num_in_urbs; i++) { + sierra_release_urb(portdata->in_urbs[i]); + portdata->in_urbs[i] = NULL; } + + usb_autopm_get_interface_no_resume(serial->interface); } static int sierra_open(struct tty_struct *tty, struct usb_serial_port *port) { struct sierra_port_private *portdata; struct usb_serial *serial = port->serial; - struct sierra_intf_private *intfdata = serial->private; + struct sierra_intf_private *intfdata = usb_get_serial_data(serial); int i; int err; int endpoint; @@ -822,11 +812,6 @@ static int sierra_open(struct tty_struct *tty, struct usb_serial_port *port) portdata = usb_get_serial_port_data(port); - /* Set some sane defaults */ - portdata->rts_state = 1; - portdata->dtr_state = 1; - - endpoint = port->bulk_in_endpointAddress; for (i = 0; i < portdata->num_in_urbs; i++) { urb = sierra_setup_urb(serial, endpoint, USB_DIR_IN, port, @@ -839,41 +824,38 @@ static int sierra_open(struct tty_struct *tty, struct usb_serial_port *port) usb_sndbulkpipe(serial->dev, endpoint) | USB_DIR_IN); err = sierra_submit_rx_urbs(port, GFP_KERNEL); - if (err) { - /* get rid of everything as in close */ - sierra_close(port); - /* restore balance for autopm */ - if (!serial->disconnected) - usb_autopm_put_interface(serial->interface); - return err; - } - sierra_send_setup(port); + if (err) + goto err_submit; - serial->interface->needs_remote_wakeup = 1; spin_lock_irq(&intfdata->susp_lock); - portdata->opened = 1; + if (++intfdata->open_ports == 1) + serial->interface->needs_remote_wakeup = 1; spin_unlock_irq(&intfdata->susp_lock); usb_autopm_put_interface(serial->interface); return 0; + +err_submit: + sierra_stop_rx_urbs(port); + + for (i = 0; i < portdata->num_in_urbs; i++) { + sierra_release_urb(portdata->in_urbs[i]); + portdata->in_urbs[i] = NULL; + } + + return err; } static void sierra_dtr_rts(struct usb_serial_port *port, int on) { - struct usb_serial *serial = port->serial; struct sierra_port_private *portdata; portdata = usb_get_serial_port_data(port); portdata->rts_state = on; portdata->dtr_state = on; - if (serial->dev) { - mutex_lock(&serial->disc_mutex); - if (!serial->disconnected) - sierra_send_setup(port); - mutex_unlock(&serial->disc_mutex); - } + sierra_send_setup(port); } static int sierra_startup(struct usb_serial *serial) @@ -934,7 +916,7 @@ static int sierra_port_probe(struct usb_serial_port *port) /* This is really the usb-serial port number of the interface * rather than the interface number. */ - ifnum = port->number - serial->minor; + ifnum = port->port_number; himemoryp = &typeA_interface_list; } @@ -957,6 +939,7 @@ static int sierra_port_remove(struct usb_serial_port *port) struct sierra_port_private *portdata; portdata = usb_get_serial_port_data(port); + usb_set_serial_port_data(port, NULL); kfree(portdata); return 0; @@ -973,6 +956,8 @@ static void stop_read_write_urbs(struct usb_serial *serial) for (i = 0; i < serial->num_ports; ++i) { port = serial->port[i]; portdata = usb_get_serial_port_data(port); + if (!portdata) + continue; sierra_stop_rx_urbs(port); usb_kill_anchored_urbs(&portdata->active); } @@ -980,58 +965,84 @@ static void stop_read_write_urbs(struct usb_serial *serial) static int sierra_suspend(struct usb_serial *serial, pm_message_t message) { - struct sierra_intf_private *intfdata; - int b; + struct sierra_intf_private *intfdata = usb_get_serial_data(serial); + spin_lock_irq(&intfdata->susp_lock); if (PMSG_IS_AUTO(message)) { - intfdata = serial->private; - spin_lock_irq(&intfdata->susp_lock); - b = intfdata->in_flight; - - if (b) { + if (intfdata->in_flight) { spin_unlock_irq(&intfdata->susp_lock); return -EBUSY; - } else { - intfdata->suspended = 1; - spin_unlock_irq(&intfdata->susp_lock); } } + intfdata->suspended = 1; + spin_unlock_irq(&intfdata->susp_lock); + stop_read_write_urbs(serial); return 0; } +/* Caller must hold susp_lock. */ +static int sierra_submit_delayed_urbs(struct usb_serial_port *port) +{ + struct sierra_port_private *portdata = usb_get_serial_port_data(port); + struct sierra_intf_private *intfdata; + struct urb *urb; + int ec = 0; + int err; + + intfdata = usb_get_serial_data(port->serial); + + for (;;) { + urb = usb_get_from_anchor(&portdata->delayed); + if (!urb) + break; + + usb_anchor_urb(urb, &portdata->active); + intfdata->in_flight++; + err = usb_submit_urb(urb, GFP_ATOMIC); + if (err) { + dev_err(&port->dev, "%s - submit urb failed: %d", + __func__, err); + ec++; + intfdata->in_flight--; + usb_unanchor_urb(urb); + kfree(urb->transfer_buffer); + usb_free_urb(urb); + + spin_lock(&portdata->lock); + portdata->outstanding_urbs--; + spin_unlock(&portdata->lock); + } + } + + if (ec) + return -EIO; + + return 0; +} + static int sierra_resume(struct usb_serial *serial) { struct usb_serial_port *port; - struct sierra_intf_private *intfdata = serial->private; - struct sierra_port_private *portdata; - struct urb *urb; + struct sierra_intf_private *intfdata = usb_get_serial_data(serial); int ec = 0; int i, err; spin_lock_irq(&intfdata->susp_lock); for (i = 0; i < serial->num_ports; i++) { port = serial->port[i]; - portdata = usb_get_serial_port_data(port); - while ((urb = usb_get_from_anchor(&portdata->delayed))) { - usb_anchor_urb(urb, &portdata->active); - intfdata->in_flight++; - err = usb_submit_urb(urb, GFP_ATOMIC); - if (err < 0) { - intfdata->in_flight--; - usb_unanchor_urb(urb); - usb_scuttle_anchored_urbs(&portdata->delayed); - break; - } - } + if (!test_bit(ASYNCB_INITIALIZED, &port->port.flags)) + continue; - if (portdata->opened) { - err = sierra_submit_rx_urbs(port, GFP_ATOMIC); - if (err) - ec++; - } + err = sierra_submit_delayed_urbs(port); + if (err) + ec++; + + err = sierra_submit_rx_urbs(port, GFP_ATOMIC); + if (err) + ec++; } intfdata->suspended = 0; spin_unlock_irq(&intfdata->susp_lock); @@ -1058,7 +1069,7 @@ static struct usb_serial_driver sierra_device = { .dtr_rts = sierra_dtr_rts, .write = sierra_write, .write_room = sierra_write_room, - .set_termios = sierra_set_termios, + .chars_in_buffer = sierra_chars_in_buffer, .tiocmget = sierra_tiocmget, .tiocmset = sierra_tiocmset, .attach = sierra_startup, diff --git a/drivers/usb/serial/spcp8x5.c b/drivers/usb/serial/spcp8x5.c index a42536af125..ef0dbf0703c 100644 --- a/drivers/usb/serial/spcp8x5.c +++ b/drivers/usb/serial/spcp8x5.c @@ -1,7 +1,7 @@ /* * spcp8x5 USB to serial adaptor driver * - * Copyright (C) 2010 Johan Hovold (jhovold@gmail.com) + * Copyright (C) 2010-2013 Johan Hovold (jhovold@gmail.com) * Copyright (C) 2006 Linxb (xubin.lin@worldplus.com.cn) * Copyright (C) 2006 S1 Corp. * @@ -13,12 +13,9 @@ * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or * (at your option) any later version. - * - * */ #include <linux/kernel.h> #include <linux/errno.h> -#include <linux/init.h> #include <linux/slab.h> #include <linux/tty.h> #include <linux/tty_driver.h> @@ -28,7 +25,10 @@ #include <linux/usb.h> #include <linux/usb/serial.h> -#define DRIVER_DESC "SPCP8x5 USB to serial adaptor driver" +#define DRIVER_DESC "SPCP8x5 USB to serial adaptor driver" + +#define SPCP825_QUIRK_NO_UART_STATUS 0x01 +#define SPCP825_QUIRK_NO_WORK_MODE 0x02 #define SPCP8x5_007_VID 0x04FC #define SPCP8x5_007_PID 0x0201 @@ -46,13 +46,15 @@ static const struct usb_device_id id_table[] = { { USB_DEVICE(SPCP8x5_INTERMATIC_VID, SPCP8x5_INTERMATIC_PID)}, { USB_DEVICE(SPCP8x5_835_VID, SPCP8x5_835_PID)}, { USB_DEVICE(SPCP8x5_008_VID, SPCP8x5_008_PID)}, - { USB_DEVICE(SPCP8x5_007_VID, SPCP8x5_007_PID)}, + { USB_DEVICE(SPCP8x5_007_VID, SPCP8x5_007_PID), + .driver_info = SPCP825_QUIRK_NO_UART_STATUS | + SPCP825_QUIRK_NO_WORK_MODE }, { } /* Terminating entry */ }; MODULE_DEVICE_TABLE(usb, id_table); struct spcp8x5_usb_ctrl_arg { - u8 type; + u8 type; u8 cmd; u8 cmd_type; u16 value; @@ -138,51 +140,35 @@ struct spcp8x5_usb_ctrl_arg { #define UART_OVERRUN_ERROR 0x40 #define UART_CTS 0x80 -enum spcp8x5_type { - SPCP825_007_TYPE, - SPCP825_008_TYPE, - SPCP825_PHILIP_TYPE, - SPCP825_INTERMATIC_TYPE, - SPCP835_TYPE, -}; - struct spcp8x5_private { - spinlock_t lock; - enum spcp8x5_type type; - wait_queue_head_t delta_msr_wait; - u8 line_control; - u8 line_status; + unsigned quirks; + spinlock_t lock; + u8 line_control; }; +static int spcp8x5_probe(struct usb_serial *serial, + const struct usb_device_id *id) +{ + usb_set_serial_data(serial, (void *)id); + + return 0; +} + static int spcp8x5_port_probe(struct usb_serial_port *port) { - struct usb_serial *serial = port->serial; + const struct usb_device_id *id = usb_get_serial_data(port->serial); struct spcp8x5_private *priv; - enum spcp8x5_type type = SPCP825_007_TYPE; - u16 product = le16_to_cpu(serial->dev->descriptor.idProduct); - - if (product == 0x0201) - type = SPCP825_007_TYPE; - else if (product == 0x0231) - type = SPCP835_TYPE; - else if (product == 0x0235) - type = SPCP825_008_TYPE; - else if (product == 0x0204) - type = SPCP825_INTERMATIC_TYPE; - else if (product == 0x0471 && - serial->dev->descriptor.idVendor == cpu_to_le16(0x081e)) - type = SPCP825_PHILIP_TYPE; - dev_dbg(&serial->dev->dev, "device type = %d\n", (int)type); priv = kzalloc(sizeof(*priv), GFP_KERNEL); if (!priv) return -ENOMEM; spin_lock_init(&priv->lock); - init_waitqueue_head(&priv->delta_msr_wait); - priv->type = type; + priv->quirks = id->driver_info; - usb_set_serial_port_data(port , priv); + usb_set_serial_port_data(port, priv); + + port->port.drain_delay = 256; return 0; } @@ -197,86 +183,79 @@ static int spcp8x5_port_remove(struct usb_serial_port *port) return 0; } -/* set the modem control line of the device. - * NOTE spcp825-007 not supported this */ -static int spcp8x5_set_ctrlLine(struct usb_device *dev, u8 value, - enum spcp8x5_type type) +static int spcp8x5_set_ctrl_line(struct usb_serial_port *port, u8 mcr) { + struct spcp8x5_private *priv = usb_get_serial_port_data(port); + struct usb_device *dev = port->serial->dev; int retval; - u8 mcr = 0 ; - if (type == SPCP825_007_TYPE) + if (priv->quirks & SPCP825_QUIRK_NO_UART_STATUS) return -EPERM; - mcr = (unsigned short)value; retval = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), SET_UART_STATUS_TYPE, SET_UART_STATUS, mcr, 0x04, NULL, 0, 100); - if (retval != 0) - dev_dbg(&dev->dev, "usb_control_msg return %#x\n", retval); + if (retval != 0) { + dev_err(&port->dev, "failed to set control lines: %d\n", + retval); + } return retval; } -/* get the modem status register of the device - * NOTE spcp825-007 not supported this */ -static int spcp8x5_get_msr(struct usb_device *dev, u8 *status, - enum spcp8x5_type type) +static int spcp8x5_get_msr(struct usb_serial_port *port, u8 *status) { - u8 *status_buffer; + struct spcp8x5_private *priv = usb_get_serial_port_data(port); + struct usb_device *dev = port->serial->dev; + u8 *buf; int ret; - /* I return Permited not support here but seem inval device - * is more fix */ - if (type == SPCP825_007_TYPE) + if (priv->quirks & SPCP825_QUIRK_NO_UART_STATUS) return -EPERM; - if (status == NULL) - return -EINVAL; - status_buffer = kmalloc(1, GFP_KERNEL); - if (!status_buffer) + buf = kzalloc(1, GFP_KERNEL); + if (!buf) return -ENOMEM; - status_buffer[0] = status[0]; ret = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0), GET_UART_STATUS, GET_UART_STATUS_TYPE, - 0, GET_UART_STATUS_MSR, status_buffer, 1, 100); + 0, GET_UART_STATUS_MSR, buf, 1, 100); if (ret < 0) - dev_dbg(&dev->dev, "Get MSR = 0x%p failed (error = %d)", - status_buffer, ret); + dev_err(&port->dev, "failed to get modem status: %d\n", ret); - dev_dbg(&dev->dev, "0xc0:0x22:0:6 %d - 0x%p ", ret, status_buffer); - status[0] = status_buffer[0]; - kfree(status_buffer); + dev_dbg(&port->dev, "0xc0:0x22:0:6 %d - 0x02%x\n", ret, *buf); + *status = *buf; + kfree(buf); return ret; } -/* select the work mode. - * NOTE this function not supported by spcp825-007 */ -static void spcp8x5_set_workMode(struct usb_device *dev, u16 value, - u16 index, enum spcp8x5_type type) +static void spcp8x5_set_work_mode(struct usb_serial_port *port, u16 value, + u16 index) { + struct spcp8x5_private *priv = usb_get_serial_port_data(port); + struct usb_device *dev = port->serial->dev; int ret; - /* I return Permited not support here but seem inval device - * is more fix */ - if (type == SPCP825_007_TYPE) + if (priv->quirks & SPCP825_QUIRK_NO_WORK_MODE) return; ret = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), SET_WORKING_MODE_TYPE, SET_WORKING_MODE, value, index, NULL, 0, 100); - dev_dbg(&dev->dev, "value = %#x , index = %#x\n", value, index); + dev_dbg(&port->dev, "value = %#x , index = %#x\n", value, index); if (ret < 0) - dev_dbg(&dev->dev, - "RTSCTS usb_control_msg(enable flowctrl) = %d\n", ret); + dev_err(&port->dev, "failed to set work mode: %d\n", ret); } static int spcp8x5_carrier_raised(struct usb_serial_port *port) { - struct spcp8x5_private *priv = usb_get_serial_port_data(port); - if (priv->line_status & MSR_STATUS_LINE_DCD) + u8 msr; + int ret; + + ret = spcp8x5_get_msr(port, &msr); + if (ret || msr & MSR_STATUS_LINE_DCD) return 1; + return 0; } @@ -295,20 +274,17 @@ static void spcp8x5_dtr_rts(struct usb_serial_port *port, int on) | MCR_CONTROL_LINE_RTS); control = priv->line_control; spin_unlock_irqrestore(&priv->lock, flags); - spcp8x5_set_ctrlLine(port->serial->dev, control , priv->type); + spcp8x5_set_ctrl_line(port, control); } static void spcp8x5_init_termios(struct tty_struct *tty) { - /* for the 1st time call this function */ tty->termios = tty_std_termios; tty->termios.c_cflag = B115200 | CS8 | CREAD | HUPCL | CLOCAL; tty->termios.c_ispeed = 115200; tty->termios.c_ospeed = 115200; } -/* set the serial param for transfer. we should check if we really need to - * transfer. if we set flow control we should do this too. */ static void spcp8x5_set_termios(struct tty_struct *tty, struct usb_serial_port *port, struct ktermios *old_termios) { @@ -316,30 +292,28 @@ static void spcp8x5_set_termios(struct tty_struct *tty, struct spcp8x5_private *priv = usb_get_serial_port_data(port); unsigned long flags; unsigned int cflag = tty->termios.c_cflag; - unsigned int old_cflag = old_termios->c_cflag; unsigned short uartdata; unsigned char buf[2] = {0, 0}; int baud; int i; u8 control; - /* check that they really want us to change something */ - if (!tty_termios_hw_change(&tty->termios, old_termios)) + if (old_termios && !tty_termios_hw_change(&tty->termios, old_termios)) return; /* set DTR/RTS active */ spin_lock_irqsave(&priv->lock, flags); control = priv->line_control; - if ((old_cflag & CBAUD) == B0) { + if (old_termios && (old_termios->c_cflag & CBAUD) == B0) { priv->line_control |= MCR_DTR; - if (!(old_cflag & CRTSCTS)) + if (!(old_termios->c_cflag & CRTSCTS)) priv->line_control |= MCR_RTS; } if (control != priv->line_control) { control = priv->line_control; spin_unlock_irqrestore(&priv->lock, flags); - spcp8x5_set_ctrlLine(serial->dev, control , priv->type); + spcp8x5_set_ctrl_line(port, control); } else { spin_unlock_irqrestore(&priv->lock, flags); } @@ -368,27 +342,24 @@ static void spcp8x5_set_termios(struct tty_struct *tty, case 1000000: buf[0] = 0x0b; break; default: - dev_err(&port->dev, "spcp825 driver does not support the " - "baudrate requested, using default of 9600.\n"); + dev_err(&port->dev, "unsupported baudrate, using 9600\n"); } /* Set Data Length : 00:5bit, 01:6bit, 10:7bit, 11:8bit */ - if (cflag & CSIZE) { - switch (cflag & CSIZE) { - case CS5: - buf[1] |= SET_UART_FORMAT_SIZE_5; - break; - case CS6: - buf[1] |= SET_UART_FORMAT_SIZE_6; - break; - case CS7: - buf[1] |= SET_UART_FORMAT_SIZE_7; - break; - default: - case CS8: - buf[1] |= SET_UART_FORMAT_SIZE_8; - break; - } + switch (cflag & CSIZE) { + case CS5: + buf[1] |= SET_UART_FORMAT_SIZE_5; + break; + case CS6: + buf[1] |= SET_UART_FORMAT_SIZE_6; + break; + case CS7: + buf[1] |= SET_UART_FORMAT_SIZE_7; + break; + default: + case CS8: + buf[1] |= SET_UART_FORMAT_SIZE_8; + break; } /* Set Stop bit2 : 0:1bit 1:2bit */ @@ -399,9 +370,9 @@ static void spcp8x5_set_termios(struct tty_struct *tty, if (cflag & PARENB) { buf[1] |= (cflag & PARODD) ? SET_UART_FORMAT_PAR_ODD : SET_UART_FORMAT_PAR_EVEN ; - } else + } else { buf[1] |= SET_UART_FORMAT_PAR_NONE; - + } uartdata = buf[0] | buf[1]<<8; i = usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0), @@ -414,22 +385,15 @@ static void spcp8x5_set_termios(struct tty_struct *tty, if (cflag & CRTSCTS) { /* enable hardware flow control */ - spcp8x5_set_workMode(serial->dev, 0x000a, - SET_WORKING_MODE_U2C, priv->type); + spcp8x5_set_work_mode(port, 0x000a, SET_WORKING_MODE_U2C); } } -/* open the serial port. do some usb system call. set termios and get the line - * status of the device. */ static int spcp8x5_open(struct tty_struct *tty, struct usb_serial_port *port) { - struct ktermios tmp_termios; struct usb_serial *serial = port->serial; struct spcp8x5_private *priv = usb_get_serial_port_data(port); int ret; - unsigned long flags; - u8 status = 0x30; - /* status 0x30 means DSR and CTS = 1 other CDC RI and delta = 0 */ usb_clear_halt(serial->dev, port->write_urb->pipe); usb_clear_halt(serial->dev, port->read_urb->pipe); @@ -440,139 +404,14 @@ static int spcp8x5_open(struct tty_struct *tty, struct usb_serial_port *port) if (ret) return ret; - spcp8x5_set_ctrlLine(serial->dev, priv->line_control , priv->type); + spcp8x5_set_ctrl_line(port, priv->line_control); - /* Setup termios */ if (tty) - spcp8x5_set_termios(tty, port, &tmp_termios); - - spcp8x5_get_msr(serial->dev, &status, priv->type); - - /* may be we should update uart status here but now we did not do */ - spin_lock_irqsave(&priv->lock, flags); - priv->line_status = status & 0xf0 ; - spin_unlock_irqrestore(&priv->lock, flags); - - port->port.drain_delay = 256; + spcp8x5_set_termios(tty, port, NULL); return usb_serial_generic_open(tty, port); } -static void spcp8x5_process_read_urb(struct urb *urb) -{ - struct usb_serial_port *port = urb->context; - struct spcp8x5_private *priv = usb_get_serial_port_data(port); - struct tty_struct *tty; - unsigned char *data = urb->transfer_buffer; - unsigned long flags; - u8 status; - char tty_flag; - - /* get tty_flag from status */ - tty_flag = TTY_NORMAL; - - spin_lock_irqsave(&priv->lock, flags); - status = priv->line_status; - priv->line_status &= ~UART_STATE_TRANSIENT_MASK; - spin_unlock_irqrestore(&priv->lock, flags); - /* wake up the wait for termios */ - wake_up_interruptible(&priv->delta_msr_wait); - - if (!urb->actual_length) - return; - - tty = tty_port_tty_get(&port->port); - if (!tty) - return; - - if (status & UART_STATE_TRANSIENT_MASK) { - /* break takes precedence over parity, which takes precedence - * over framing errors */ - if (status & UART_BREAK_ERROR) - tty_flag = TTY_BREAK; - else if (status & UART_PARITY_ERROR) - tty_flag = TTY_PARITY; - else if (status & UART_FRAME_ERROR) - tty_flag = TTY_FRAME; - dev_dbg(&port->dev, "tty_flag = %d\n", tty_flag); - - /* overrun is special, not associated with a char */ - if (status & UART_OVERRUN_ERROR) - tty_insert_flip_char(tty, 0, TTY_OVERRUN); - - if (status & UART_DCD) - usb_serial_handle_dcd_change(port, tty, - priv->line_status & MSR_STATUS_LINE_DCD); - } - - tty_insert_flip_string_fixed_flag(tty, data, tty_flag, - urb->actual_length); - tty_flip_buffer_push(tty); - tty_kref_put(tty); -} - -static int spcp8x5_wait_modem_info(struct usb_serial_port *port, - unsigned int arg) -{ - struct spcp8x5_private *priv = usb_get_serial_port_data(port); - unsigned long flags; - unsigned int prevstatus; - unsigned int status; - unsigned int changed; - - spin_lock_irqsave(&priv->lock, flags); - prevstatus = priv->line_status; - spin_unlock_irqrestore(&priv->lock, flags); - - while (1) { - /* wake up in bulk read */ - interruptible_sleep_on(&priv->delta_msr_wait); - - /* see if a signal did it */ - if (signal_pending(current)) - return -ERESTARTSYS; - - spin_lock_irqsave(&priv->lock, flags); - status = priv->line_status; - spin_unlock_irqrestore(&priv->lock, flags); - - changed = prevstatus^status; - - if (((arg & TIOCM_RNG) && (changed & MSR_STATUS_LINE_RI)) || - ((arg & TIOCM_DSR) && (changed & MSR_STATUS_LINE_DSR)) || - ((arg & TIOCM_CD) && (changed & MSR_STATUS_LINE_DCD)) || - ((arg & TIOCM_CTS) && (changed & MSR_STATUS_LINE_CTS))) - return 0; - - prevstatus = status; - } - /* NOTREACHED */ - return 0; -} - -static int spcp8x5_ioctl(struct tty_struct *tty, - unsigned int cmd, unsigned long arg) -{ - struct usb_serial_port *port = tty->driver_data; - - dev_dbg(&port->dev, "%s (%d) cmd = 0x%04x\n", __func__, - port->number, cmd); - - switch (cmd) { - case TIOCMIWAIT: - dev_dbg(&port->dev, "%s (%d) TIOCMIWAIT\n", __func__, - port->number); - return spcp8x5_wait_modem_info(port, arg); - - default: - dev_dbg(&port->dev, "%s not supported = 0x%04x", __func__, - cmd); - break; - } - - return -ENOIOCTLCMD; -} - static int spcp8x5_tiocmset(struct tty_struct *tty, unsigned int set, unsigned int clear) { @@ -593,7 +432,7 @@ static int spcp8x5_tiocmset(struct tty_struct *tty, control = priv->line_control; spin_unlock_irqrestore(&priv->lock, flags); - return spcp8x5_set_ctrlLine(port->serial->dev, control , priv->type); + return spcp8x5_set_ctrl_line(port, control); } static int spcp8x5_tiocmget(struct tty_struct *tty) @@ -602,12 +441,15 @@ static int spcp8x5_tiocmget(struct tty_struct *tty) struct spcp8x5_private *priv = usb_get_serial_port_data(port); unsigned long flags; unsigned int mcr; - unsigned int status; + u8 status; unsigned int result; + result = spcp8x5_get_msr(port, &status); + if (result) + return result; + spin_lock_irqsave(&priv->lock, flags); mcr = priv->line_control; - status = priv->line_status; spin_unlock_irqrestore(&priv->lock, flags); result = ((mcr & MCR_DTR) ? TIOCM_DTR : 0) @@ -620,7 +462,6 @@ static int spcp8x5_tiocmget(struct tty_struct *tty) return result; } -/* All of the device info needed for the spcp8x5 SIO serial converter */ static struct usb_serial_driver spcp8x5_device = { .driver = { .owner = THIS_MODULE, @@ -628,17 +469,16 @@ static struct usb_serial_driver spcp8x5_device = { }, .id_table = id_table, .num_ports = 1, - .open = spcp8x5_open, + .open = spcp8x5_open, .dtr_rts = spcp8x5_dtr_rts, .carrier_raised = spcp8x5_carrier_raised, - .set_termios = spcp8x5_set_termios, + .set_termios = spcp8x5_set_termios, .init_termios = spcp8x5_init_termios, - .ioctl = spcp8x5_ioctl, - .tiocmget = spcp8x5_tiocmget, - .tiocmset = spcp8x5_tiocmset, + .tiocmget = spcp8x5_tiocmget, + .tiocmset = spcp8x5_tiocmset, + .probe = spcp8x5_probe, .port_probe = spcp8x5_port_probe, .port_remove = spcp8x5_port_remove, - .process_read_urb = spcp8x5_process_read_urb, }; static struct usb_serial_driver * const serial_drivers[] = { diff --git a/drivers/usb/serial/ssu100.c b/drivers/usb/serial/ssu100.c index 4543ea35022..a7fe664b6b7 100644 --- a/drivers/usb/serial/ssu100.c +++ b/drivers/usb/serial/ssu100.c @@ -6,7 +6,6 @@ */ #include <linux/errno.h> -#include <linux/init.h> #include <linux/slab.h> #include <linux/tty.h> #include <linux/tty_driver.h> @@ -61,8 +60,6 @@ struct ssu100_port_private { spinlock_t status_lock; u8 shadowLSR; u8 shadowMSR; - wait_queue_head_t delta_msr_wait; /* Used for TIOCMIWAIT */ - struct async_icount icount; }; static inline int ssu100_control_msg(struct usb_device *dev, @@ -316,11 +313,6 @@ static int ssu100_open(struct tty_struct *tty, struct usb_serial_port *port) return usb_serial_generic_open(tty, port); } -static void ssu100_close(struct usb_serial_port *port) -{ - usb_serial_generic_close(port); -} - static int get_serial_info(struct usb_serial_port *port, struct serial_struct __user *retinfo) { @@ -330,7 +322,7 @@ static int get_serial_info(struct usb_serial_port *port, return -EFAULT; memset(&tmp, 0, sizeof(tmp)); - tmp.line = port->serial->minor; + tmp.line = port->minor; tmp.port = 0; tmp.irq = 0; tmp.flags = ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ; @@ -344,90 +336,19 @@ static int get_serial_info(struct usb_serial_port *port, return 0; } -static int wait_modem_info(struct usb_serial_port *port, unsigned int arg) -{ - struct ssu100_port_private *priv = usb_get_serial_port_data(port); - struct async_icount prev, cur; - unsigned long flags; - - spin_lock_irqsave(&priv->status_lock, flags); - prev = priv->icount; - spin_unlock_irqrestore(&priv->status_lock, flags); - - while (1) { - wait_event_interruptible(priv->delta_msr_wait, - ((priv->icount.rng != prev.rng) || - (priv->icount.dsr != prev.dsr) || - (priv->icount.dcd != prev.dcd) || - (priv->icount.cts != prev.cts))); - - if (signal_pending(current)) - return -ERESTARTSYS; - - spin_lock_irqsave(&priv->status_lock, flags); - cur = priv->icount; - spin_unlock_irqrestore(&priv->status_lock, flags); - - if ((prev.rng == cur.rng) && - (prev.dsr == cur.dsr) && - (prev.dcd == cur.dcd) && - (prev.cts == cur.cts)) - return -EIO; - - if ((arg & TIOCM_RNG && (prev.rng != cur.rng)) || - (arg & TIOCM_DSR && (prev.dsr != cur.dsr)) || - (arg & TIOCM_CD && (prev.dcd != cur.dcd)) || - (arg & TIOCM_CTS && (prev.cts != cur.cts))) - return 0; - } - return 0; -} - -static int ssu100_get_icount(struct tty_struct *tty, - struct serial_icounter_struct *icount) -{ - struct usb_serial_port *port = tty->driver_data; - struct ssu100_port_private *priv = usb_get_serial_port_data(port); - struct async_icount cnow = priv->icount; - - icount->cts = cnow.cts; - icount->dsr = cnow.dsr; - icount->rng = cnow.rng; - icount->dcd = cnow.dcd; - icount->rx = cnow.rx; - icount->tx = cnow.tx; - icount->frame = cnow.frame; - icount->overrun = cnow.overrun; - icount->parity = cnow.parity; - icount->brk = cnow.brk; - icount->buf_overrun = cnow.buf_overrun; - - return 0; -} - - - static int ssu100_ioctl(struct tty_struct *tty, unsigned int cmd, unsigned long arg) { struct usb_serial_port *port = tty->driver_data; - dev_dbg(&port->dev, "%s cmd 0x%04x\n", __func__, cmd); - switch (cmd) { case TIOCGSERIAL: return get_serial_info(port, (struct serial_struct __user *) arg); - - case TIOCMIWAIT: - return wait_modem_info(port, arg); - default: break; } - dev_dbg(&port->dev, "%s arg not supported\n", __func__); - return -ENOIOCTLCMD; } @@ -445,7 +366,6 @@ static int ssu100_port_probe(struct usb_serial_port *port) return -ENOMEM; spin_lock_init(&priv->status_lock); - init_waitqueue_head(&priv->delta_msr_wait); usb_set_serial_port_data(port, priv); @@ -506,19 +426,16 @@ static void ssu100_dtr_rts(struct usb_serial_port *port, int on) { struct usb_device *dev = port->serial->dev; - mutex_lock(&port->serial->disc_mutex); - if (!port->serial->disconnected) { - /* Disable flow control */ - if (!on && - ssu100_setregister(dev, 0, UART_MCR, 0) < 0) + /* Disable flow control */ + if (!on) { + if (ssu100_setregister(dev, 0, UART_MCR, 0) < 0) dev_err(&port->dev, "error from flowcontrol urb\n"); - /* drop RTS and DTR */ - if (on) - set_mctrl(dev, TIOCM_DTR | TIOCM_RTS); - else - clear_mctrl(dev, TIOCM_DTR | TIOCM_RTS); } - mutex_unlock(&port->serial->disc_mutex); + /* drop RTS and DTR */ + if (on) + set_mctrl(dev, TIOCM_DTR | TIOCM_RTS); + else + clear_mctrl(dev, TIOCM_DTR | TIOCM_RTS); } static void ssu100_update_msr(struct usb_serial_port *port, u8 msr) @@ -533,14 +450,14 @@ static void ssu100_update_msr(struct usb_serial_port *port, u8 msr) if (msr & UART_MSR_ANY_DELTA) { /* update input line counters */ if (msr & UART_MSR_DCTS) - priv->icount.cts++; + port->icount.cts++; if (msr & UART_MSR_DDSR) - priv->icount.dsr++; + port->icount.dsr++; if (msr & UART_MSR_DDCD) - priv->icount.dcd++; + port->icount.dcd++; if (msr & UART_MSR_TERI) - priv->icount.rng++; - wake_up_interruptible(&priv->delta_msr_wait); + port->icount.rng++; + wake_up_interruptible(&port->port.delta_msr_wait); } } @@ -559,22 +476,22 @@ static void ssu100_update_lsr(struct usb_serial_port *port, u8 lsr, /* we always want to update icount, but we only want to * update tty_flag for one case */ if (lsr & UART_LSR_BI) { - priv->icount.brk++; + port->icount.brk++; *tty_flag = TTY_BREAK; usb_serial_handle_break(port); } if (lsr & UART_LSR_PE) { - priv->icount.parity++; + port->icount.parity++; if (*tty_flag == TTY_NORMAL) *tty_flag = TTY_PARITY; } if (lsr & UART_LSR_FE) { - priv->icount.frame++; + port->icount.frame++; if (*tty_flag == TTY_NORMAL) *tty_flag = TTY_FRAME; } if (lsr & UART_LSR_OE){ - priv->icount.overrun++; + port->icount.overrun++; if (*tty_flag == TTY_NORMAL) *tty_flag = TTY_OVERRUN; } @@ -582,8 +499,7 @@ static void ssu100_update_lsr(struct usb_serial_port *port, u8 lsr, } -static int ssu100_process_packet(struct urb *urb, - struct tty_struct *tty) +static void ssu100_process_read_urb(struct urb *urb) { struct usb_serial_port *port = urb->context; char *packet = (char *)urb->transfer_buffer; @@ -598,7 +514,8 @@ static int ssu100_process_packet(struct urb *urb, if (packet[2] == 0x00) { ssu100_update_lsr(port, packet[3], &flag); if (flag == TTY_OVERRUN) - tty_insert_flip_char(tty, 0, TTY_OVERRUN); + tty_insert_flip_char(&port->port, 0, + TTY_OVERRUN); } if (packet[2] == 0x01) ssu100_update_msr(port, packet[3]); @@ -609,34 +526,17 @@ static int ssu100_process_packet(struct urb *urb, ch = packet; if (!len) - return 0; /* status only */ + return; /* status only */ if (port->port.console && port->sysrq) { for (i = 0; i < len; i++, ch++) { if (!usb_serial_handle_sysrq_char(port, *ch)) - tty_insert_flip_char(tty, *ch, flag); + tty_insert_flip_char(&port->port, *ch, flag); } } else - tty_insert_flip_string_fixed_flag(tty, ch, flag, len); - - return len; -} - -static void ssu100_process_read_urb(struct urb *urb) -{ - struct usb_serial_port *port = urb->context; - struct tty_struct *tty; - int count; - - tty = tty_port_tty_get(&port->port); - if (!tty) - return; - - count = ssu100_process_packet(urb, tty); + tty_insert_flip_string_fixed_flag(&port->port, ch, flag, len); - if (count) - tty_flip_buffer_push(tty); - tty_kref_put(tty); + tty_flip_buffer_push(&port->port); } static struct usb_serial_driver ssu100_device = { @@ -648,7 +548,6 @@ static struct usb_serial_driver ssu100_device = { .id_table = id_table, .num_ports = 1, .open = ssu100_open, - .close = ssu100_close, .attach = ssu100_attach, .port_probe = ssu100_port_probe, .port_remove = ssu100_port_remove, @@ -656,10 +555,10 @@ static struct usb_serial_driver ssu100_device = { .process_read_urb = ssu100_process_read_urb, .tiocmget = ssu100_tiocmget, .tiocmset = ssu100_tiocmset, - .get_icount = ssu100_get_icount, + .tiocmiwait = usb_serial_generic_tiocmiwait, + .get_icount = usb_serial_generic_get_icount, .ioctl = ssu100_ioctl, .set_termios = ssu100_set_termios, - .disconnect = usb_serial_generic_disconnect, }; static struct usb_serial_driver * const serial_drivers[] = { diff --git a/drivers/usb/serial/symbolserial.c b/drivers/usb/serial/symbolserial.c index 701fffa8431..8fceec7298e 100644 --- a/drivers/usb/serial/symbolserial.c +++ b/drivers/usb/serial/symbolserial.c @@ -1,6 +1,7 @@ /* * Symbol USB barcode to serial driver * + * Copyright (C) 2013 Johan Hovold <jhovold@gmail.com> * Copyright (C) 2009 Greg Kroah-Hartman <gregkh@suse.de> * Copyright (C) 2009 Novell Inc. * @@ -10,7 +11,6 @@ */ #include <linux/kernel.h> -#include <linux/init.h> #include <linux/tty.h> #include <linux/slab.h> #include <linux/tty_driver.h> @@ -26,29 +26,18 @@ static const struct usb_device_id id_table[] = { }; MODULE_DEVICE_TABLE(usb, id_table); -/* This structure holds all of the individual device information */ struct symbol_private { - struct usb_device *udev; - struct usb_serial *serial; - struct usb_serial_port *port; - unsigned char *int_buffer; - struct urb *int_urb; - int buffer_size; - u8 bInterval; - u8 int_address; spinlock_t lock; /* protects the following flags */ bool throttled; bool actually_throttled; - bool rts; }; static void symbol_int_callback(struct urb *urb) { - struct symbol_private *priv = urb->context; + struct usb_serial_port *port = urb->context; + struct symbol_private *priv = usb_get_serial_port_data(port); unsigned char *data = urb->transfer_buffer; - struct usb_serial_port *port = priv->port; int status = urb->status; - struct tty_struct *tty; int result; int data_length; @@ -82,16 +71,10 @@ static void symbol_int_callback(struct urb *urb) * we pretty much just ignore the size and send everything * else to the tty layer. */ - tty = tty_port_tty_get(&port->port); - if (tty) { - tty_insert_flip_string(tty, &data[1], data_length); - tty_flip_buffer_push(tty); - tty_kref_put(tty); - } + tty_insert_flip_string(&port->port, &data[1], data_length); + tty_flip_buffer_push(&port->port); } else { - dev_dbg(&priv->udev->dev, - "Improper amount of data received from the device, " - "%d bytes", urb->actual_length); + dev_dbg(&port->dev, "%s - short packet\n", __func__); } exit: @@ -99,12 +82,7 @@ exit: /* Continue trying to always read if we should */ if (!priv->throttled) { - usb_fill_int_urb(priv->int_urb, priv->udev, - usb_rcvintpipe(priv->udev, - priv->int_address), - priv->int_buffer, priv->buffer_size, - symbol_int_callback, priv, priv->bInterval); - result = usb_submit_urb(priv->int_urb, GFP_ATOMIC); + result = usb_submit_urb(port->interrupt_in_urb, GFP_ATOMIC); if (result) dev_err(&port->dev, "%s - failed resubmitting read urb, error %d\n", @@ -123,15 +101,10 @@ static int symbol_open(struct tty_struct *tty, struct usb_serial_port *port) spin_lock_irqsave(&priv->lock, flags); priv->throttled = false; priv->actually_throttled = false; - priv->port = port; spin_unlock_irqrestore(&priv->lock, flags); /* Start reading from the device */ - usb_fill_int_urb(priv->int_urb, priv->udev, - usb_rcvintpipe(priv->udev, priv->int_address), - priv->int_buffer, priv->buffer_size, - symbol_int_callback, priv, priv->bInterval); - result = usb_submit_urb(priv->int_urb, GFP_KERNEL); + result = usb_submit_urb(port->interrupt_in_urb, GFP_KERNEL); if (result) dev_err(&port->dev, "%s - failed resubmitting read urb, error %d\n", @@ -141,10 +114,7 @@ static int symbol_open(struct tty_struct *tty, struct usb_serial_port *port) static void symbol_close(struct usb_serial_port *port) { - struct symbol_private *priv = usb_get_serial_data(port->serial); - - /* shutdown our urbs */ - usb_kill_urb(priv->int_urb); + usb_kill_urb(port->interrupt_in_urb); } static void symbol_throttle(struct tty_struct *tty) @@ -171,7 +141,7 @@ static void symbol_unthrottle(struct tty_struct *tty) spin_unlock_irq(&priv->lock); if (was_throttled) { - result = usb_submit_urb(priv->int_urb, GFP_KERNEL); + result = usb_submit_urb(port->interrupt_in_urb, GFP_KERNEL); if (result) dev_err(&port->dev, "%s - failed submitting read urb, error %d\n", @@ -181,89 +151,36 @@ static void symbol_unthrottle(struct tty_struct *tty) static int symbol_startup(struct usb_serial *serial) { + if (!serial->num_interrupt_in) { + dev_err(&serial->dev->dev, "no interrupt-in endpoint\n"); + return -ENODEV; + } + + return 0; +} + +static int symbol_port_probe(struct usb_serial_port *port) +{ struct symbol_private *priv; - struct usb_host_interface *intf; - int i; - int retval = -ENOMEM; - bool int_in_found = false; - /* create our private serial structure */ priv = kzalloc(sizeof(*priv), GFP_KERNEL); - if (priv == NULL) { - dev_err(&serial->dev->dev, "%s - Out of memory\n", __func__); + if (!priv) return -ENOMEM; - } + spin_lock_init(&priv->lock); - priv->serial = serial; - priv->port = serial->port[0]; - priv->udev = serial->dev; - - /* find our interrupt endpoint */ - intf = serial->interface->altsetting; - for (i = 0; i < intf->desc.bNumEndpoints; ++i) { - struct usb_endpoint_descriptor *endpoint; - - endpoint = &intf->endpoint[i].desc; - if (!usb_endpoint_is_int_in(endpoint)) - continue; - - priv->int_urb = usb_alloc_urb(0, GFP_KERNEL); - if (!priv->int_urb) { - dev_err(&priv->udev->dev, "out of memory\n"); - goto error; - } - - priv->buffer_size = usb_endpoint_maxp(endpoint) * 2; - priv->int_buffer = kmalloc(priv->buffer_size, GFP_KERNEL); - if (!priv->int_buffer) { - dev_err(&priv->udev->dev, "out of memory\n"); - goto error; - } - - priv->int_address = endpoint->bEndpointAddress; - priv->bInterval = endpoint->bInterval; - - /* set up our int urb */ - usb_fill_int_urb(priv->int_urb, priv->udev, - usb_rcvintpipe(priv->udev, - endpoint->bEndpointAddress), - priv->int_buffer, priv->buffer_size, - symbol_int_callback, priv, priv->bInterval); - - int_in_found = true; - break; - } - if (!int_in_found) { - dev_err(&priv->udev->dev, - "Error - the proper endpoints were not found!\n"); - goto error; - } + usb_set_serial_port_data(port, priv); - usb_set_serial_data(serial, priv); return 0; - -error: - usb_free_urb(priv->int_urb); - kfree(priv->int_buffer); - kfree(priv); - return retval; -} - -static void symbol_disconnect(struct usb_serial *serial) -{ - struct symbol_private *priv = usb_get_serial_data(serial); - - usb_kill_urb(priv->int_urb); - usb_free_urb(priv->int_urb); } -static void symbol_release(struct usb_serial *serial) +static int symbol_port_remove(struct usb_serial_port *port) { - struct symbol_private *priv = usb_get_serial_data(serial); + struct symbol_private *priv = usb_get_serial_port_data(port); - kfree(priv->int_buffer); kfree(priv); + + return 0; } static struct usb_serial_driver symbol_device = { @@ -274,12 +191,13 @@ static struct usb_serial_driver symbol_device = { .id_table = id_table, .num_ports = 1, .attach = symbol_startup, + .port_probe = symbol_port_probe, + .port_remove = symbol_port_remove, .open = symbol_open, .close = symbol_close, - .disconnect = symbol_disconnect, - .release = symbol_release, .throttle = symbol_throttle, .unthrottle = symbol_unthrottle, + .read_int_callback = symbol_int_callback, }; static struct usb_serial_driver * const serial_drivers[] = { diff --git a/drivers/usb/serial/ti_usb_3410_5052.c b/drivers/usb/serial/ti_usb_3410_5052.c index f2530d2ef3c..3dd3ff8c50d 100644 --- a/drivers/usb/serial/ti_usb_3410_5052.c +++ b/drivers/usb/serial/ti_usb_3410_5052.c @@ -21,7 +21,6 @@ #include <linux/kernel.h> #include <linux/errno.h> #include <linux/firmware.h> -#include <linux/init.h> #include <linux/slab.h> #include <linux/tty.h> #include <linux/tty_driver.h> @@ -45,8 +44,6 @@ #define TI_FIRMWARE_BUF_SIZE 16284 -#define TI_WRITE_BUF_SIZE 1024 - #define TI_TRANSFER_TIMEOUT 2 #define TI_DEFAULT_CLOSING_WAIT 4000 /* in .01 secs */ @@ -67,21 +64,15 @@ struct ti_port { int tp_is_open; __u8 tp_msr; - __u8 tp_lsr; __u8 tp_shadow_mcr; __u8 tp_uart_mode; /* 232 or 485 modes */ unsigned int tp_uart_base_addr; int tp_flags; - int tp_closing_wait;/* in .01 secs */ - struct async_icount tp_icount; - wait_queue_head_t tp_msr_wait; /* wait for msr change */ - wait_queue_head_t tp_write_wait; struct ti_device *tp_tdev; struct usb_serial_port *tp_port; spinlock_t tp_lock; int tp_read_urb_state; int tp_write_urb_in_use; - struct kfifo write_fifo; }; struct ti_device { @@ -105,12 +96,11 @@ static int ti_write(struct tty_struct *tty, struct usb_serial_port *port, const unsigned char *data, int count); static int ti_write_room(struct tty_struct *tty); static int ti_chars_in_buffer(struct tty_struct *tty); +static bool ti_tx_empty(struct usb_serial_port *port); static void ti_throttle(struct tty_struct *tty); static void ti_unthrottle(struct tty_struct *tty); static int ti_ioctl(struct tty_struct *tty, unsigned int cmd, unsigned long arg); -static int ti_get_icount(struct tty_struct *tty, - struct serial_icounter_struct *icount); static void ti_set_termios(struct tty_struct *tty, struct usb_serial_port *port, struct ktermios *old_termios); static int ti_tiocmget(struct tty_struct *tty); @@ -121,19 +111,17 @@ static void ti_interrupt_callback(struct urb *urb); static void ti_bulk_in_callback(struct urb *urb); static void ti_bulk_out_callback(struct urb *urb); -static void ti_recv(struct device *dev, struct tty_struct *tty, - unsigned char *data, int length); +static void ti_recv(struct usb_serial_port *port, unsigned char *data, + int length); static void ti_send(struct ti_port *tport); static int ti_set_mcr(struct ti_port *tport, unsigned int mcr); -static int ti_get_lsr(struct ti_port *tport); +static int ti_get_lsr(struct ti_port *tport, u8 *lsr); static int ti_get_serial_info(struct ti_port *tport, struct serial_struct __user *ret_arg); static int ti_set_serial_info(struct tty_struct *tty, struct ti_port *tport, struct serial_struct __user *new_arg); static void ti_handle_new_msr(struct ti_port *tport, __u8 msr); -static void ti_drain(struct ti_port *tport, unsigned long timeout, int flush); - static void ti_stop_read(struct ti_port *tport, struct tty_struct *tty); static int ti_restart_read(struct ti_port *tport, struct tty_struct *tty); @@ -152,20 +140,9 @@ static int ti_download_firmware(struct ti_device *tdev); /* module parameters */ static int closing_wait = TI_DEFAULT_CLOSING_WAIT; -static ushort vendor_3410[TI_EXTRA_VID_PID_COUNT]; -static unsigned int vendor_3410_count; -static ushort product_3410[TI_EXTRA_VID_PID_COUNT]; -static unsigned int product_3410_count; -static ushort vendor_5052[TI_EXTRA_VID_PID_COUNT]; -static unsigned int vendor_5052_count; -static ushort product_5052[TI_EXTRA_VID_PID_COUNT]; -static unsigned int product_5052_count; /* supported devices */ -/* the array dimension is the number of default entries plus */ -/* TI_EXTRA_VID_PID_COUNT user defined entries plus 1 terminating */ -/* null entry */ -static struct usb_device_id ti_id_table_3410[15+TI_EXTRA_VID_PID_COUNT+1] = { +static const struct usb_device_id ti_id_table_3410[] = { { USB_DEVICE(TI_VENDOR_ID, TI_3410_PRODUCT_ID) }, { USB_DEVICE(TI_VENDOR_ID, TI_3410_EZ430_ID) }, { USB_DEVICE(MTS_VENDOR_ID, MTS_GSM_NO_FW_PRODUCT_ID) }, @@ -179,18 +156,21 @@ static struct usb_device_id ti_id_table_3410[15+TI_EXTRA_VID_PID_COUNT+1] = { { USB_DEVICE(IBM_VENDOR_ID, IBM_4543_PRODUCT_ID) }, { USB_DEVICE(IBM_VENDOR_ID, IBM_454B_PRODUCT_ID) }, { USB_DEVICE(IBM_VENDOR_ID, IBM_454C_PRODUCT_ID) }, - { USB_DEVICE(ABBOTT_VENDOR_ID, ABBOTT_PRODUCT_ID) }, + { USB_DEVICE(ABBOTT_VENDOR_ID, ABBOTT_STEREO_PLUG_ID) }, + { USB_DEVICE(ABBOTT_VENDOR_ID, ABBOTT_STRIP_PORT_ID) }, { USB_DEVICE(TI_VENDOR_ID, FRI2_PRODUCT_ID) }, + { } /* terminator */ }; -static struct usb_device_id ti_id_table_5052[5+TI_EXTRA_VID_PID_COUNT+1] = { +static const struct usb_device_id ti_id_table_5052[] = { { USB_DEVICE(TI_VENDOR_ID, TI_5052_BOOT_PRODUCT_ID) }, { USB_DEVICE(TI_VENDOR_ID, TI_5152_BOOT_PRODUCT_ID) }, { USB_DEVICE(TI_VENDOR_ID, TI_5052_EEPROM_PRODUCT_ID) }, { USB_DEVICE(TI_VENDOR_ID, TI_5052_FIRMWARE_PRODUCT_ID) }, + { } /* terminator */ }; -static struct usb_device_id ti_id_table_combined[19+2*TI_EXTRA_VID_PID_COUNT+1] = { +static const struct usb_device_id ti_id_table_combined[] = { { USB_DEVICE(TI_VENDOR_ID, TI_3410_PRODUCT_ID) }, { USB_DEVICE(TI_VENDOR_ID, TI_3410_EZ430_ID) }, { USB_DEVICE(MTS_VENDOR_ID, MTS_GSM_NO_FW_PRODUCT_ID) }, @@ -209,8 +189,9 @@ static struct usb_device_id ti_id_table_combined[19+2*TI_EXTRA_VID_PID_COUNT+1] { USB_DEVICE(IBM_VENDOR_ID, IBM_454B_PRODUCT_ID) }, { USB_DEVICE(IBM_VENDOR_ID, IBM_454C_PRODUCT_ID) }, { USB_DEVICE(ABBOTT_VENDOR_ID, ABBOTT_PRODUCT_ID) }, + { USB_DEVICE(ABBOTT_VENDOR_ID, ABBOTT_STRIP_PORT_ID) }, { USB_DEVICE(TI_VENDOR_ID, FRI2_PRODUCT_ID) }, - { } + { } /* terminator */ }; static struct usb_serial_driver ti_1port_device = { @@ -230,13 +211,15 @@ static struct usb_serial_driver ti_1port_device = { .write = ti_write, .write_room = ti_write_room, .chars_in_buffer = ti_chars_in_buffer, + .tx_empty = ti_tx_empty, .throttle = ti_throttle, .unthrottle = ti_unthrottle, .ioctl = ti_ioctl, .set_termios = ti_set_termios, .tiocmget = ti_tiocmget, .tiocmset = ti_tiocmset, - .get_icount = ti_get_icount, + .tiocmiwait = usb_serial_generic_tiocmiwait, + .get_icount = usb_serial_generic_get_icount, .break_ctl = ti_break, .read_int_callback = ti_interrupt_callback, .read_bulk_callback = ti_bulk_in_callback, @@ -260,13 +243,15 @@ static struct usb_serial_driver ti_2port_device = { .write = ti_write, .write_room = ti_write_room, .chars_in_buffer = ti_chars_in_buffer, + .tx_empty = ti_tx_empty, .throttle = ti_throttle, .unthrottle = ti_unthrottle, .ioctl = ti_ioctl, .set_termios = ti_set_termios, .tiocmget = ti_tiocmget, .tiocmset = ti_tiocmset, - .get_icount = ti_get_icount, + .tiocmiwait = usb_serial_generic_tiocmiwait, + .get_icount = usb_serial_generic_get_icount, .break_ctl = ti_break, .read_int_callback = ti_interrupt_callback, .read_bulk_callback = ti_bulk_in_callback, @@ -295,61 +280,12 @@ module_param(closing_wait, int, S_IRUGO | S_IWUSR); MODULE_PARM_DESC(closing_wait, "Maximum wait for data to drain in close, in .01 secs, default is 4000"); -module_param_array(vendor_3410, ushort, &vendor_3410_count, S_IRUGO); -MODULE_PARM_DESC(vendor_3410, - "Vendor ids for 3410 based devices, 1-5 short integers"); -module_param_array(product_3410, ushort, &product_3410_count, S_IRUGO); -MODULE_PARM_DESC(product_3410, - "Product ids for 3410 based devices, 1-5 short integers"); -module_param_array(vendor_5052, ushort, &vendor_5052_count, S_IRUGO); -MODULE_PARM_DESC(vendor_5052, - "Vendor ids for 5052 based devices, 1-5 short integers"); -module_param_array(product_5052, ushort, &product_5052_count, S_IRUGO); -MODULE_PARM_DESC(product_5052, - "Product ids for 5052 based devices, 1-5 short integers"); - MODULE_DEVICE_TABLE(usb, ti_id_table_combined); +module_usb_serial_driver(serial_drivers, ti_id_table_combined); /* Functions */ -static int __init ti_init(void) -{ - int i, j, c; - - /* insert extra vendor and product ids */ - c = ARRAY_SIZE(ti_id_table_combined) - 2 * TI_EXTRA_VID_PID_COUNT - 1; - j = ARRAY_SIZE(ti_id_table_3410) - TI_EXTRA_VID_PID_COUNT - 1; - for (i = 0; i < min(vendor_3410_count, product_3410_count); i++, j++, c++) { - ti_id_table_3410[j].idVendor = vendor_3410[i]; - ti_id_table_3410[j].idProduct = product_3410[i]; - ti_id_table_3410[j].match_flags = USB_DEVICE_ID_MATCH_DEVICE; - ti_id_table_combined[c].idVendor = vendor_3410[i]; - ti_id_table_combined[c].idProduct = product_3410[i]; - ti_id_table_combined[c].match_flags = USB_DEVICE_ID_MATCH_DEVICE; - } - j = ARRAY_SIZE(ti_id_table_5052) - TI_EXTRA_VID_PID_COUNT - 1; - for (i = 0; i < min(vendor_5052_count, product_5052_count); i++, j++, c++) { - ti_id_table_5052[j].idVendor = vendor_5052[i]; - ti_id_table_5052[j].idProduct = product_5052[i]; - ti_id_table_5052[j].match_flags = USB_DEVICE_ID_MATCH_DEVICE; - ti_id_table_combined[c].idVendor = vendor_5052[i]; - ti_id_table_combined[c].idProduct = product_5052[i]; - ti_id_table_combined[c].match_flags = USB_DEVICE_ID_MATCH_DEVICE; - } - - return usb_serial_register_drivers(serial_drivers, KBUILD_MODNAME, ti_id_table_combined); -} - -static void __exit ti_exit(void) -{ - usb_serial_deregister_drivers(serial_drivers); -} - -module_init(ti_init); -module_exit(ti_exit); - - static int ti_startup(struct usb_serial *serial) { struct ti_device *tdev; @@ -357,23 +293,22 @@ static int ti_startup(struct usb_serial *serial) int status; dev_dbg(&dev->dev, - "%s - product 0x%4X, num configurations %d, configuration value %d", + "%s - product 0x%4X, num configurations %d, configuration value %d\n", __func__, le16_to_cpu(dev->descriptor.idProduct), dev->descriptor.bNumConfigurations, dev->actconfig->desc.bConfigurationValue); /* create device structure */ tdev = kzalloc(sizeof(struct ti_device), GFP_KERNEL); - if (tdev == NULL) { - dev_err(&dev->dev, "%s - out of memory\n", __func__); + if (!tdev) return -ENOMEM; - } + mutex_init(&tdev->td_open_close_lock); tdev->td_serial = serial; usb_set_serial_data(serial, tdev); /* determine device type */ - if (usb_match_id(serial->interface, ti_id_table_3410)) + if (serial->type == &ti_1port_device) tdev->td_is_3410 = 1; dev_dbg(&dev->dev, "%s - device type is %s\n", __func__, tdev->td_is_3410 ? "3410" : "5052"); @@ -431,19 +366,15 @@ static int ti_port_probe(struct usb_serial_port *port) tport->tp_uart_base_addr = TI_UART1_BASE_ADDR; else tport->tp_uart_base_addr = TI_UART2_BASE_ADDR; - tport->tp_closing_wait = closing_wait; - init_waitqueue_head(&tport->tp_msr_wait); - init_waitqueue_head(&tport->tp_write_wait); - if (kfifo_alloc(&tport->write_fifo, TI_WRITE_BUF_SIZE, GFP_KERNEL)) { - kfree(tport); - return -ENOMEM; - } + port->port.closing_wait = msecs_to_jiffies(10 * closing_wait); tport->tp_port = port; tport->tp_tdev = usb_get_serial_data(port->serial); tport->tp_uart_mode = 0; /* default is RS232 */ usb_set_serial_port_data(port, tport); + port->port.drain_delay = 3; + return 0; } @@ -452,7 +383,6 @@ static int ti_port_remove(struct usb_serial_port *port) struct ti_port *tport; tport = usb_get_serial_port_data(port); - kfifo_free(&tport->write_fifo); kfree(tport); return 0; @@ -480,9 +410,7 @@ static int ti_open(struct tty_struct *tty, struct usb_serial_port *port) if (mutex_lock_interruptible(&tdev->td_open_close_lock)) return -ERESTARTSYS; - port_number = port->number - port->serial->minor; - - memset(&(tport->tp_icount), 0x00, sizeof(tport->tp_icount)); + port_number = port->port_number; tport->tp_msr = 0; tport->tp_shadow_mcr |= (TI_MCR_RTS | TI_MCR_DTR); @@ -606,6 +534,7 @@ static void ti_close(struct usb_serial_port *port) int port_number; int status; int do_unlock; + unsigned long flags; tdev = usb_get_serial_data(port->serial); tport = usb_get_serial_port_data(port); @@ -614,13 +543,14 @@ static void ti_close(struct usb_serial_port *port) tport->tp_is_open = 0; - ti_drain(tport, (tport->tp_closing_wait*HZ)/100, 1); - usb_kill_urb(port->read_urb); usb_kill_urb(port->write_urb); tport->tp_write_urb_in_use = 0; + spin_lock_irqsave(&tport->tp_lock, flags); + kfifo_reset_out(&port->write_fifo); + spin_unlock_irqrestore(&tport->tp_lock, flags); - port_number = port->number - port->serial->minor; + port_number = port->port_number; dev_dbg(&port->dev, "%s - sending TI_CLOSE_PORT\n", __func__); status = ti_command_out_sync(tdev, TI_CLOSE_PORT, @@ -656,7 +586,7 @@ static int ti_write(struct tty_struct *tty, struct usb_serial_port *port, if (tport == NULL || !tport->tp_is_open) return -ENODEV; - count = kfifo_in_locked(&tport->write_fifo, data, count, + count = kfifo_in_locked(&port->write_fifo, data, count, &tport->tp_lock); ti_send(tport); @@ -675,7 +605,7 @@ static int ti_write_room(struct tty_struct *tty) return 0; spin_lock_irqsave(&tport->tp_lock, flags); - room = kfifo_avail(&tport->write_fifo); + room = kfifo_avail(&port->write_fifo); spin_unlock_irqrestore(&tport->tp_lock, flags); dev_dbg(&port->dev, "%s - returns %d\n", __func__, room); @@ -694,13 +624,25 @@ static int ti_chars_in_buffer(struct tty_struct *tty) return 0; spin_lock_irqsave(&tport->tp_lock, flags); - chars = kfifo_len(&tport->write_fifo); + chars = kfifo_len(&port->write_fifo); spin_unlock_irqrestore(&tport->tp_lock, flags); dev_dbg(&port->dev, "%s - returns %d\n", __func__, chars); return chars; } +static bool ti_tx_empty(struct usb_serial_port *port) +{ + struct ti_port *tport = usb_get_serial_port_data(port); + int ret; + u8 lsr; + + ret = ti_get_lsr(tport, &lsr); + if (!ret && !(lsr & TI_LSR_TX_EMPTY)) + return false; + + return true; +} static void ti_throttle(struct tty_struct *tty) { @@ -733,40 +675,11 @@ static void ti_unthrottle(struct tty_struct *tty) } } -static int ti_get_icount(struct tty_struct *tty, - struct serial_icounter_struct *icount) -{ - struct usb_serial_port *port = tty->driver_data; - struct ti_port *tport = usb_get_serial_port_data(port); - struct async_icount cnow = tport->tp_icount; - - dev_dbg(&port->dev, "%s - TIOCGICOUNT RX=%d, TX=%d\n", __func__, - cnow.rx, cnow.tx); - - icount->cts = cnow.cts; - icount->dsr = cnow.dsr; - icount->rng = cnow.rng; - icount->dcd = cnow.dcd; - icount->rx = cnow.rx; - icount->tx = cnow.tx; - icount->frame = cnow.frame; - icount->overrun = cnow.overrun; - icount->parity = cnow.parity; - icount->brk = cnow.brk; - icount->buf_overrun = cnow.buf_overrun; - - return 0; -} - static int ti_ioctl(struct tty_struct *tty, unsigned int cmd, unsigned long arg) { struct usb_serial_port *port = tty->driver_data; struct ti_port *tport = usb_get_serial_port_data(port); - struct async_icount cnow; - struct async_icount cprev; - - dev_dbg(&port->dev, "%s - cmd = 0x%04X\n", __func__, cmd); if (tport == NULL) return -ENODEV; @@ -780,25 +693,6 @@ static int ti_ioctl(struct tty_struct *tty, dev_dbg(&port->dev, "%s - TIOCSSERIAL\n", __func__); return ti_set_serial_info(tty, tport, (struct serial_struct __user *)arg); - case TIOCMIWAIT: - dev_dbg(&port->dev, "%s - TIOCMIWAIT\n", __func__); - cprev = tport->tp_icount; - while (1) { - interruptible_sleep_on(&tport->tp_msr_wait); - if (signal_pending(current)) - return -ERESTARTSYS; - cnow = tport->tp_icount; - if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr && - cnow.dcd == cprev.dcd && cnow.cts == cprev.cts) - return -EIO; /* no change => error */ - if (((arg & TIOCM_RNG) && (cnow.rng != cprev.rng)) || - ((arg & TIOCM_DSR) && (cnow.dsr != cprev.dsr)) || - ((arg & TIOCM_CD) && (cnow.dcd != cprev.dcd)) || - ((arg & TIOCM_CTS) && (cnow.cts != cprev.cts))) - return 0; - cprev = cnow; - } - break; } return -ENOIOCTLCMD; } @@ -812,7 +706,7 @@ static void ti_set_termios(struct tty_struct *tty, tcflag_t cflag, iflag; int baud; int status; - int port_number = port->number - port->serial->minor; + int port_number = port->port_number; unsigned int mcr; cflag = tty->termios.c_cflag; @@ -826,10 +720,8 @@ static void ti_set_termios(struct tty_struct *tty, return; config = kmalloc(sizeof(*config), GFP_KERNEL); - if (!config) { - dev_err(&port->dev, "%s - out of memory\n", __func__); + if (!config) return; - } config->wFlags = 0; @@ -911,7 +803,7 @@ static void ti_set_termios(struct tty_struct *tty, tty_encode_baud_rate(tty, baud, baud); dev_dbg(&port->dev, - "%s - BaudRate=%d, wBaudRate=%d, wFlags=0x%04X, bDataBits=%d, bParity=%d, bStopBits=%d, cXon=%d, cXoff=%d, bUartMode=%d", + "%s - BaudRate=%d, wBaudRate=%d, wFlags=0x%04X, bDataBits=%d, bParity=%d, bStopBits=%d, cXon=%d, cXoff=%d, bUartMode=%d\n", __func__, baud, config->wBaudRate, config->wFlags, config->bDataBits, config->bParity, config->bStopBits, config->cXon, config->cXoff, config->bUartMode); @@ -1016,8 +908,6 @@ static void ti_break(struct tty_struct *tty, int break_state) if (tport == NULL) return; - ti_drain(tport, (tport->tp_closing_wait*HZ)/100, 0); - status = ti_write_byte(port, tport->tp_tdev, tport->tp_uart_base_addr + TI_UART_OFFSET_LCR, TI_LCR_BREAK, break_state == -1 ? TI_LCR_BREAK : 0); @@ -1118,7 +1008,6 @@ static void ti_bulk_in_callback(struct urb *urb) struct device *dev = &urb->dev->dev; int status = urb->status; int retval = 0; - struct tty_struct *tty; switch (status) { case 0: @@ -1128,13 +1017,11 @@ static void ti_bulk_in_callback(struct urb *urb) case -ESHUTDOWN: dev_dbg(dev, "%s - urb shutting down, %d\n", __func__, status); tport->tp_tdev->td_urb_error = 1; - wake_up_interruptible(&tport->tp_write_wait); return; default: dev_err(dev, "%s - nonzero urb status, %d\n", __func__, status); tport->tp_tdev->td_urb_error = 1; - wake_up_interruptible(&tport->tp_write_wait); } if (status == -EPIPE) @@ -1145,24 +1032,18 @@ static void ti_bulk_in_callback(struct urb *urb) return; } - tty = tty_port_tty_get(&port->port); - if (tty) { - if (urb->actual_length) { - usb_serial_debug_data(dev, __func__, urb->actual_length, - urb->transfer_buffer); + if (urb->actual_length) { + usb_serial_debug_data(dev, __func__, urb->actual_length, + urb->transfer_buffer); - if (!tport->tp_is_open) - dev_dbg(dev, "%s - port closed, dropping data\n", - __func__); - else - ti_recv(&urb->dev->dev, tty, - urb->transfer_buffer, - urb->actual_length); - spin_lock(&tport->tp_lock); - tport->tp_icount.rx += urb->actual_length; - spin_unlock(&tport->tp_lock); - } - tty_kref_put(tty); + if (!tport->tp_is_open) + dev_dbg(dev, "%s - port closed, dropping data\n", + __func__); + else + ti_recv(port, urb->transfer_buffer, urb->actual_length); + spin_lock(&tport->tp_lock); + port->icount.rx += urb->actual_length; + spin_unlock(&tport->tp_lock); } exit: @@ -1196,13 +1077,11 @@ static void ti_bulk_out_callback(struct urb *urb) case -ESHUTDOWN: dev_dbg(&port->dev, "%s - urb shutting down, %d\n", __func__, status); tport->tp_tdev->td_urb_error = 1; - wake_up_interruptible(&tport->tp_write_wait); return; default: dev_err_console(port, "%s - nonzero urb status, %d\n", __func__, status); tport->tp_tdev->td_urb_error = 1; - wake_up_interruptible(&tport->tp_write_wait); } /* send any buffered data */ @@ -1210,24 +1089,23 @@ static void ti_bulk_out_callback(struct urb *urb) } -static void ti_recv(struct device *dev, struct tty_struct *tty, - unsigned char *data, int length) +static void ti_recv(struct usb_serial_port *port, unsigned char *data, + int length) { int cnt; do { - cnt = tty_insert_flip_string(tty, data, length); + cnt = tty_insert_flip_string(&port->port, data, length); if (cnt < length) { - dev_err(dev, "%s - dropping data, %d bytes lost\n", + dev_err(&port->dev, "%s - dropping data, %d bytes lost\n", __func__, length - cnt); if (cnt == 0) break; } - tty_flip_buffer_push(tty); + tty_flip_buffer_push(&port->port); data += cnt; length -= cnt; } while (length > 0); - } @@ -1235,7 +1113,6 @@ static void ti_send(struct ti_port *tport) { int count, result; struct usb_serial_port *port = tport->tp_port; - struct tty_struct *tty = tty_port_tty_get(&port->port); /* FIXME */ unsigned long flags; spin_lock_irqsave(&tport->tp_lock, flags); @@ -1243,7 +1120,7 @@ static void ti_send(struct ti_port *tport) if (tport->tp_write_urb_in_use) goto unlock; - count = kfifo_out(&tport->write_fifo, + count = kfifo_out(&port->write_fifo, port->write_urb->transfer_buffer, port->bulk_out_size); @@ -1271,19 +1148,16 @@ static void ti_send(struct ti_port *tport) /* TODO: reschedule ti_send */ } else { spin_lock_irqsave(&tport->tp_lock, flags); - tport->tp_icount.tx += count; + port->icount.tx += count; spin_unlock_irqrestore(&tport->tp_lock, flags); } /* more room in the buffer for new writes, wakeup */ - if (tty) - tty_wakeup(tty); - tty_kref_put(tty); - wake_up_interruptible(&tport->tp_write_wait); + tty_port_tty_wakeup(&port->port); + return; unlock: spin_unlock_irqrestore(&tport->tp_lock, flags); - tty_kref_put(tty); return; } @@ -1306,20 +1180,18 @@ static int ti_set_mcr(struct ti_port *tport, unsigned int mcr) } -static int ti_get_lsr(struct ti_port *tport) +static int ti_get_lsr(struct ti_port *tport, u8 *lsr) { int size, status; struct ti_device *tdev = tport->tp_tdev; struct usb_serial_port *port = tport->tp_port; - int port_number = port->number - port->serial->minor; + int port_number = port->port_number; struct ti_port_status *data; size = sizeof(struct ti_port_status); data = kmalloc(size, GFP_KERNEL); - if (!data) { - dev_err(&port->dev, "%s - out of memory\n", __func__); + if (!data) return -ENOMEM; - } status = ti_command_in_sync(tdev, TI_GET_PORT_STATUS, (__u8)(TI_UART1_PORT+port_number), 0, (__u8 *)data, size); @@ -1332,7 +1204,7 @@ static int ti_get_lsr(struct ti_port *tport) dev_dbg(&port->dev, "%s - lsr 0x%02X\n", __func__, data->bLSR); - tport->tp_lsr = data->bLSR; + *lsr = data->bLSR; free_data: kfree(data); @@ -1345,19 +1217,24 @@ static int ti_get_serial_info(struct ti_port *tport, { struct usb_serial_port *port = tport->tp_port; struct serial_struct ret_serial; + unsigned cwait; if (!ret_arg) return -EFAULT; + cwait = port->port.closing_wait; + if (cwait != ASYNC_CLOSING_WAIT_NONE) + cwait = jiffies_to_msecs(cwait) / 10; + memset(&ret_serial, 0, sizeof(ret_serial)); ret_serial.type = PORT_16550A; - ret_serial.line = port->serial->minor; - ret_serial.port = port->number - port->serial->minor; + ret_serial.line = port->minor; + ret_serial.port = port->port_number; ret_serial.flags = tport->tp_flags; - ret_serial.xmit_fifo_size = TI_WRITE_BUF_SIZE; + ret_serial.xmit_fifo_size = kfifo_size(&port->write_fifo); ret_serial.baud_base = tport->tp_tdev->td_is_3410 ? 921600 : 460800; - ret_serial.closing_wait = tport->tp_closing_wait; + ret_serial.closing_wait = cwait; if (copy_to_user(ret_arg, &ret_serial, sizeof(*ret_arg))) return -EFAULT; @@ -1370,12 +1247,17 @@ static int ti_set_serial_info(struct tty_struct *tty, struct ti_port *tport, struct serial_struct __user *new_arg) { struct serial_struct new_serial; + unsigned cwait; if (copy_from_user(&new_serial, new_arg, sizeof(new_serial))) return -EFAULT; + cwait = new_serial.closing_wait; + if (cwait != ASYNC_CLOSING_WAIT_NONE) + cwait = msecs_to_jiffies(10 * new_serial.closing_wait); + tport->tp_flags = new_serial.flags & TI_SET_SERIAL_FLAGS; - tport->tp_closing_wait = new_serial.closing_wait; + tport->tp_port->port.closing_wait = cwait; return 0; } @@ -1391,7 +1273,7 @@ static void ti_handle_new_msr(struct ti_port *tport, __u8 msr) if (msr & TI_MSR_DELTA_MASK) { spin_lock_irqsave(&tport->tp_lock, flags); - icount = &tport->tp_icount; + icount = &tport->tp_port->icount; if (msr & TI_MSR_DELTA_CTS) icount->cts++; if (msr & TI_MSR_DELTA_DSR) @@ -1400,7 +1282,7 @@ static void ti_handle_new_msr(struct ti_port *tport, __u8 msr) icount->dcd++; if (msr & TI_MSR_DELTA_RI) icount->rng++; - wake_up_interruptible(&tport->tp_msr_wait); + wake_up_interruptible(&tport->tp_port->port.delta_msr_wait); spin_unlock_irqrestore(&tport->tp_lock, flags); } @@ -1420,56 +1302,6 @@ static void ti_handle_new_msr(struct ti_port *tport, __u8 msr) } -static void ti_drain(struct ti_port *tport, unsigned long timeout, int flush) -{ - struct ti_device *tdev = tport->tp_tdev; - struct usb_serial_port *port = tport->tp_port; - wait_queue_t wait; - - spin_lock_irq(&tport->tp_lock); - - /* wait for data to drain from the buffer */ - tdev->td_urb_error = 0; - init_waitqueue_entry(&wait, current); - add_wait_queue(&tport->tp_write_wait, &wait); - for (;;) { - set_current_state(TASK_INTERRUPTIBLE); - if (kfifo_len(&tport->write_fifo) == 0 - || timeout == 0 || signal_pending(current) - || tdev->td_urb_error - || port->serial->disconnected) /* disconnect */ - break; - spin_unlock_irq(&tport->tp_lock); - timeout = schedule_timeout(timeout); - spin_lock_irq(&tport->tp_lock); - } - set_current_state(TASK_RUNNING); - remove_wait_queue(&tport->tp_write_wait, &wait); - - /* flush any remaining data in the buffer */ - if (flush) - kfifo_reset_out(&tport->write_fifo); - - spin_unlock_irq(&tport->tp_lock); - - mutex_lock(&port->serial->disc_mutex); - /* wait for data to drain from the device */ - /* wait for empty tx register, plus 20 ms */ - timeout += jiffies; - tport->tp_lsr &= ~TI_LSR_TX_EMPTY; - while ((long)(jiffies - timeout) < 0 && !signal_pending(current) - && !(tport->tp_lsr&TI_LSR_TX_EMPTY) && !tdev->td_urb_error - && !port->serial->disconnected) { - if (ti_get_lsr(tport)) - break; - mutex_unlock(&port->serial->disc_mutex); - msleep_interruptible(20); - mutex_lock(&port->serial->disc_mutex); - } - mutex_unlock(&port->serial->disc_mutex); -} - - static void ti_stop_read(struct ti_port *tport, struct tty_struct *tty) { unsigned long flags; @@ -1559,10 +1391,8 @@ static int ti_write_byte(struct usb_serial_port *port, size = sizeof(struct ti_write_data_bytes) + 2; data = kmalloc(size, GFP_KERNEL); - if (!data) { - dev_err(&port->dev, "%s - out of memory\n", __func__); + if (!data) return -ENOMEM; - } data->bAddrType = TI_RW_DATA_ADDR_XDATA; data->bDataType = TI_RW_DATA_BYTE; @@ -1624,14 +1454,15 @@ static int ti_download_firmware(struct ti_device *tdev) char buf[32]; /* try ID specific firmware first, then try generic firmware */ - sprintf(buf, "ti_usb-v%04x-p%04x.fw", dev->descriptor.idVendor, - dev->descriptor.idProduct); + sprintf(buf, "ti_usb-v%04x-p%04x.fw", + le16_to_cpu(dev->descriptor.idVendor), + le16_to_cpu(dev->descriptor.idProduct)); status = request_firmware(&fw_p, buf, &dev->dev); if (status != 0) { buf[0] = '\0'; - if (dev->descriptor.idVendor == MTS_VENDOR_ID) { - switch (dev->descriptor.idProduct) { + if (le16_to_cpu(dev->descriptor.idVendor) == MTS_VENDOR_ID) { + switch (le16_to_cpu(dev->descriptor.idProduct)) { case MTS_CDMA_PRODUCT_ID: strcpy(buf, "mts_cdma.fw"); break; @@ -1677,7 +1508,6 @@ static int ti_download_firmware(struct ti_device *tdev) status = ti_do_download(dev, pipe, buffer, fw_p->size); kfree(buffer); } else { - dev_dbg(&dev->dev, "%s ENOMEM\n", __func__); status = -ENOMEM; } release_firmware(fw_p); diff --git a/drivers/usb/serial/ti_usb_3410_5052.h b/drivers/usb/serial/ti_usb_3410_5052.h index b353e7e3d48..4a2423e84d5 100644 --- a/drivers/usb/serial/ti_usb_3410_5052.h +++ b/drivers/usb/serial/ti_usb_3410_5052.h @@ -52,7 +52,9 @@ /* Abbott Diabetics vendor and product ids */ #define ABBOTT_VENDOR_ID 0x1a61 -#define ABBOTT_PRODUCT_ID 0x3410 +#define ABBOTT_STEREO_PLUG_ID 0x3410 +#define ABBOTT_PRODUCT_ID ABBOTT_STEREO_PLUG_ID +#define ABBOTT_STRIP_PORT_ID 0x3420 /* Commands */ #define TI_GET_VERSION 0x01 diff --git a/drivers/usb/serial/usb-serial-simple.c b/drivers/usb/serial/usb-serial-simple.c new file mode 100644 index 00000000000..fb79775447b --- /dev/null +++ b/drivers/usb/serial/usb-serial-simple.c @@ -0,0 +1,110 @@ +/* + * USB Serial "Simple" driver + * + * Copyright (C) 2001-2006,2008,2013 Greg Kroah-Hartman <greg@kroah.com> + * Copyright (C) 2005 Arthur Huillet (ahuillet@users.sf.net) + * Copyright (C) 2005 Thomas Hergenhahn <thomas.hergenhahn@suse.de> + * Copyright (C) 2009 Outpost Embedded, LLC + * Copyright (C) 2010 Zilogic Systems <code@zilogic.com> + * Copyright (C) 2013 Wei Shuai <cpuwolf@gmail.com> + * Copyright (C) 2013 Linux Foundation + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License version + * 2 as published by the Free Software Foundation. + */ + +#include <linux/kernel.h> +#include <linux/tty.h> +#include <linux/module.h> +#include <linux/usb.h> +#include <linux/usb/serial.h> + +#define DEVICE(vendor, IDS) \ +static const struct usb_device_id vendor##_id_table[] = { \ + IDS(), \ + { }, \ +}; \ +static struct usb_serial_driver vendor##_device = { \ + .driver = { \ + .owner = THIS_MODULE, \ + .name = #vendor, \ + }, \ + .id_table = vendor##_id_table, \ + .num_ports = 1, \ +}; + + +/* ZIO Motherboard USB driver */ +#define ZIO_IDS() \ + { USB_DEVICE(0x1CBE, 0x0103) } +DEVICE(zio, ZIO_IDS); + +/* Funsoft Serial USB driver */ +#define FUNSOFT_IDS() \ + { USB_DEVICE(0x1404, 0xcddc) } +DEVICE(funsoft, FUNSOFT_IDS); + +/* Infineon Flashloader driver */ +#define FLASHLOADER_IDS() \ + { USB_DEVICE(0x8087, 0x0716) } +DEVICE(flashloader, FLASHLOADER_IDS); + +/* ViVOpay USB Serial Driver */ +#define VIVOPAY_IDS() \ + { USB_DEVICE(0x1d5f, 0x1004) } /* ViVOpay 8800 */ +DEVICE(vivopay, VIVOPAY_IDS); + +/* Motorola USB Phone driver */ +#define MOTO_IDS() \ + { USB_DEVICE(0x05c6, 0x3197) }, /* unknown Motorola phone */ \ + { USB_DEVICE(0x0c44, 0x0022) }, /* unknown Mororola phone */ \ + { USB_DEVICE(0x22b8, 0x2a64) }, /* Motorola KRZR K1m */ \ + { USB_DEVICE(0x22b8, 0x2c84) }, /* Motorola VE240 phone */ \ + { USB_DEVICE(0x22b8, 0x2c64) } /* Motorola V950 phone */ +DEVICE(moto_modem, MOTO_IDS); + +/* HP4x (48/49) Generic Serial driver */ +#define HP4X_IDS() \ + { USB_DEVICE(0x03f0, 0x0121) } +DEVICE(hp4x, HP4X_IDS); + +/* Suunto ANT+ USB Driver */ +#define SUUNTO_IDS() \ + { USB_DEVICE(0x0fcf, 0x1008) }, \ + { USB_DEVICE(0x0fcf, 0x1009) } /* Dynastream ANT USB-m Stick */ +DEVICE(suunto, SUUNTO_IDS); + +/* Siemens USB/MPI adapter */ +#define SIEMENS_IDS() \ + { USB_DEVICE(0x908, 0x0004) } +DEVICE(siemens_mpi, SIEMENS_IDS); + +/* All of the above structures mushed into two lists */ +static struct usb_serial_driver * const serial_drivers[] = { + &zio_device, + &funsoft_device, + &flashloader_device, + &vivopay_device, + &moto_modem_device, + &hp4x_device, + &suunto_device, + &siemens_mpi_device, + NULL +}; + +static const struct usb_device_id id_table[] = { + ZIO_IDS(), + FUNSOFT_IDS(), + FLASHLOADER_IDS(), + VIVOPAY_IDS(), + MOTO_IDS(), + HP4X_IDS(), + SUUNTO_IDS(), + SIEMENS_IDS(), + { }, +}; +MODULE_DEVICE_TABLE(usb, id_table); + +module_usb_serial_driver(serial_drivers, id_table); +MODULE_LICENSE("GPL"); diff --git a/drivers/usb/serial/usb-serial.c b/drivers/usb/serial/usb-serial.c index 64bda135ba7..02de3110fe9 100644 --- a/drivers/usb/serial/usb-serial.c +++ b/drivers/usb/serial/usb-serial.c @@ -1,6 +1,7 @@ /* * USB Serial Converter driver * + * Copyright (C) 2009 - 2013 Johan Hovold (jhovold@gmail.com) * Copyright (C) 1999 - 2012 Greg Kroah-Hartman (greg@kroah.com) * Copyright (C) 2000 Peter Berger (pberger@brimson.com) * Copyright (C) 2000 Al Borchers (borchers@steinerpoint.com) @@ -14,7 +15,6 @@ * * See Documentation/usb/usb-serial.txt for more information on using this * driver - * */ #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt @@ -37,11 +37,15 @@ #include <linux/usb.h> #include <linux/usb/serial.h> #include <linux/kfifo.h> +#include <linux/idr.h> #include "pl2303.h" #define DRIVER_AUTHOR "Greg Kroah-Hartman <gregkh@linuxfoundation.org>" #define DRIVER_DESC "USB Serial Driver core" +#define USB_SERIAL_TTY_MAJOR 188 +#define USB_SERIAL_TTY_MINORS 512 /* should be enough for a while */ + /* There is no MODULE_DEVICE_TABLE for usbserial.c. Instead the MODULE_DEVICE_TABLE declarations in each serial driver cause the "hotplug" program to pull in whatever module is necessary @@ -49,82 +53,75 @@ drivers depend on it. */ -/* initially all NULL */ -static struct usb_serial *serial_table[SERIAL_TTY_MINORS]; +static DEFINE_IDR(serial_minors); static DEFINE_MUTEX(table_lock); static LIST_HEAD(usb_serial_driver_list); /* - * Look up the serial structure. If it is found and it hasn't been - * disconnected, return with its disc_mutex held and its refcount - * incremented. Otherwise return NULL. + * Look up the serial port structure. If it is found and it hasn't been + * disconnected, return with the parent usb_serial structure's disc_mutex held + * and its refcount incremented. Otherwise return NULL. */ -struct usb_serial *usb_serial_get_by_index(unsigned index) +struct usb_serial_port *usb_serial_port_get_by_minor(unsigned minor) { struct usb_serial *serial; + struct usb_serial_port *port; mutex_lock(&table_lock); - serial = serial_table[index]; - - if (serial) { - mutex_lock(&serial->disc_mutex); - if (serial->disconnected) { - mutex_unlock(&serial->disc_mutex); - serial = NULL; - } else { - kref_get(&serial->kref); - } + port = idr_find(&serial_minors, minor); + if (!port) + goto exit; + + serial = port->serial; + mutex_lock(&serial->disc_mutex); + if (serial->disconnected) { + mutex_unlock(&serial->disc_mutex); + port = NULL; + } else { + kref_get(&serial->kref); } +exit: mutex_unlock(&table_lock); - return serial; + return port; } -static struct usb_serial *get_free_serial(struct usb_serial *serial, - int num_ports, unsigned int *minor) +static int allocate_minors(struct usb_serial *serial, int num_ports) { + struct usb_serial_port *port; unsigned int i, j; - int good_spot; + int minor; dev_dbg(&serial->interface->dev, "%s %d\n", __func__, num_ports); - *minor = 0; mutex_lock(&table_lock); - for (i = 0; i < SERIAL_TTY_MINORS; ++i) { - if (serial_table[i]) - continue; - - good_spot = 1; - for (j = 1; j <= num_ports-1; ++j) - if ((i+j >= SERIAL_TTY_MINORS) || (serial_table[i+j])) { - good_spot = 0; - i += j; - break; - } - if (good_spot == 0) - continue; - - *minor = i; - j = 0; - dev_dbg(&serial->interface->dev, "%s - minor base = %d\n", __func__, *minor); - for (i = *minor; (i < (*minor + num_ports)) && (i < SERIAL_TTY_MINORS); ++i) { - serial_table[i] = serial; - serial->port[j++]->number = i; - } - mutex_unlock(&table_lock); - return serial; + for (i = 0; i < num_ports; ++i) { + port = serial->port[i]; + minor = idr_alloc(&serial_minors, port, 0, 0, GFP_KERNEL); + if (minor < 0) + goto error; + port->minor = minor; + port->port_number = i; } + serial->minors_reserved = 1; mutex_unlock(&table_lock); - return NULL; + return 0; +error: + /* unwind the already allocated minors */ + for (j = 0; j < i; ++j) + idr_remove(&serial_minors, serial->port[j]->minor); + mutex_unlock(&table_lock); + return minor; } -static void return_serial(struct usb_serial *serial) +static void release_minors(struct usb_serial *serial) { int i; mutex_lock(&table_lock); for (i = 0; i < serial->num_ports; ++i) - serial_table[serial->minor + i] = NULL; + idr_remove(&serial_minors, serial->port[i]->minor); mutex_unlock(&table_lock); + serial->minors_reserved = 0; } static void destroy_serial(struct kref *kref) @@ -136,10 +133,10 @@ static void destroy_serial(struct kref *kref) serial = to_usb_serial(kref); /* return the minor range that this device had */ - if (serial->minor != SERIAL_TTY_NO_MINOR) - return_serial(serial); + if (serial->minors_reserved) + release_minors(serial); - if (serial->attached) + if (serial->attached && serial->type->release) serial->type->release(serial); /* Now that nothing is using the ports, they can be freed */ @@ -151,6 +148,7 @@ static void destroy_serial(struct kref *kref) } } + usb_put_intf(serial->interface); usb_put_dev(serial->dev); kfree(serial); } @@ -185,13 +183,11 @@ static int serial_install(struct tty_driver *driver, struct tty_struct *tty) struct usb_serial_port *port; int retval = -ENODEV; - serial = usb_serial_get_by_index(idx); - if (!serial) + port = usb_serial_port_get_by_minor(idx); + if (!port) return retval; - port = serial->port[idx - serial->minor]; - if (!port) - goto error_no_port; + serial = port->serial; if (!try_module_get(serial->type->driver.owner)) goto error_module_get; @@ -218,13 +214,12 @@ static int serial_install(struct tty_driver *driver, struct tty_struct *tty) error_get_interface: module_put(serial->type->driver.owner); error_module_get: - error_no_port: usb_serial_put(serial); mutex_unlock(&serial->disc_mutex); return retval; } -static int serial_activate(struct tty_port *tport, struct tty_struct *tty) +static int serial_port_activate(struct tty_port *tport, struct tty_struct *tty) { struct usb_serial_port *port = container_of(tport, struct usb_serial_port, port); @@ -248,30 +243,27 @@ static int serial_open(struct tty_struct *tty, struct file *filp) { struct usb_serial_port *port = tty->driver_data; - dev_dbg(tty->dev, "%s - port %d\n", __func__, port->number); + dev_dbg(tty->dev, "%s\n", __func__); + return tty_port_open(&port->port, tty, filp); } /** - * serial_down - shut down hardware + * serial_port_shutdown - shut down hardware * @tport: tty port to shut down * - * Shut down a USB serial port unless it is the console. We never - * shut down the console hardware as it will always be in use. Serialized - * against activate by the tport mutex and kept to matching open/close pairs + * Shut down a USB serial port. Serialized against activate by the + * tport mutex and kept to matching open/close pairs * of calls by the ASYNCB_INITIALIZED flag. + * + * Not called if tty is console. */ -static void serial_down(struct tty_port *tport) +static void serial_port_shutdown(struct tty_port *tport) { struct usb_serial_port *port = container_of(tport, struct usb_serial_port, port); struct usb_serial_driver *drv = port->serial->type; - /* - * The console is magical. Do not hang up the console hardware - * or there will be tears. - */ - if (port->port.console) - return; + if (drv->close) drv->close(port); } @@ -280,7 +272,8 @@ static void serial_hangup(struct tty_struct *tty) { struct usb_serial_port *port = tty->driver_data; - dev_dbg(tty->dev, "%s - port %d\n", __func__, port->number); + dev_dbg(tty->dev, "%s\n", __func__); + tty_port_hangup(&port->port); } @@ -288,7 +281,8 @@ static void serial_close(struct tty_struct *tty, struct file *filp) { struct usb_serial_port *port = tty->driver_data; - dev_dbg(tty->dev, "%s - port %d\n", __func__, port->number); + dev_dbg(tty->dev, "%s\n", __func__); + tty_port_close(&port->port, tty, filp); } @@ -307,14 +301,14 @@ static void serial_cleanup(struct tty_struct *tty) struct usb_serial *serial; struct module *owner; + dev_dbg(tty->dev, "%s\n", __func__); + /* The console is magical. Do not hang up the console hardware * or there will be tears. */ if (port->port.console) return; - dev_dbg(tty->dev, "%s - port %d\n", __func__, port->number); - tty->driver_data = NULL; serial = port->serial; @@ -338,10 +332,8 @@ static int serial_write(struct tty_struct *tty, const unsigned char *buf, if (port->serial->dev->state == USB_STATE_NOTATTACHED) goto exit; - dev_dbg(tty->dev, "%s - port %d, %d byte(s)\n", __func__, - port->number, count); + dev_dbg(tty->dev, "%s - %d byte(s)\n", __func__, count); - /* pass on to the driver specific version of this function */ retval = port->serial->type->write(tty, port, buf, count); if (retval < 0) retval = usb_translate_errors(retval); @@ -353,32 +345,46 @@ static int serial_write_room(struct tty_struct *tty) { struct usb_serial_port *port = tty->driver_data; - dev_dbg(tty->dev, "%s - port %d\n", __func__, port->number); - /* pass on to the driver specific version of this function */ + dev_dbg(tty->dev, "%s\n", __func__); + return port->serial->type->write_room(tty); } static int serial_chars_in_buffer(struct tty_struct *tty) { struct usb_serial_port *port = tty->driver_data; + struct usb_serial *serial = port->serial; - dev_dbg(tty->dev, "%s - port %d\n", __func__, port->number); + dev_dbg(tty->dev, "%s\n", __func__); - /* if the device was unplugged then any remaining characters - fell out of the connector ;) */ - if (port->serial->disconnected) + if (serial->disconnected) return 0; - /* pass on to the driver specific version of this function */ - return port->serial->type->chars_in_buffer(tty); + + return serial->type->chars_in_buffer(tty); +} + +static void serial_wait_until_sent(struct tty_struct *tty, int timeout) +{ + struct usb_serial_port *port = tty->driver_data; + struct usb_serial *serial = port->serial; + + dev_dbg(tty->dev, "%s\n", __func__); + + if (!port->serial->type->wait_until_sent) + return; + + mutex_lock(&serial->disc_mutex); + if (!serial->disconnected) + port->serial->type->wait_until_sent(tty, timeout); + mutex_unlock(&serial->disc_mutex); } static void serial_throttle(struct tty_struct *tty) { struct usb_serial_port *port = tty->driver_data; - dev_dbg(tty->dev, "%s - port %d\n", __func__, port->number); + dev_dbg(tty->dev, "%s\n", __func__); - /* pass on to the driver specific version of this function */ if (port->serial->type->throttle) port->serial->type->throttle(tty); } @@ -387,9 +393,8 @@ static void serial_unthrottle(struct tty_struct *tty) { struct usb_serial_port *port = tty->driver_data; - dev_dbg(tty->dev, "%s - port %d\n", __func__, port->number); + dev_dbg(tty->dev, "%s\n", __func__); - /* pass on to the driver specific version of this function */ if (port->serial->type->unthrottle) port->serial->type->unthrottle(tty); } @@ -398,17 +403,20 @@ static int serial_ioctl(struct tty_struct *tty, unsigned int cmd, unsigned long arg) { struct usb_serial_port *port = tty->driver_data; - int retval = -ENODEV; - - dev_dbg(tty->dev, "%s - port %d, cmd 0x%.4x\n", __func__, - port->number, cmd); + int retval = -ENOIOCTLCMD; + + dev_dbg(tty->dev, "%s - cmd 0x%04x\n", __func__, cmd); + + switch (cmd) { + case TIOCMIWAIT: + if (port->serial->type->tiocmiwait) + retval = port->serial->type->tiocmiwait(tty, arg); + break; + default: + if (port->serial->type->ioctl) + retval = port->serial->type->ioctl(tty, cmd, arg); + } - /* pass on to the driver specific version of this function - if it is available */ - if (port->serial->type->ioctl) { - retval = port->serial->type->ioctl(tty, cmd, arg); - } else - retval = -ENOIOCTLCMD; return retval; } @@ -416,10 +424,8 @@ static void serial_set_termios(struct tty_struct *tty, struct ktermios *old) { struct usb_serial_port *port = tty->driver_data; - dev_dbg(tty->dev, "%s - port %d\n", __func__, port->number); + dev_dbg(tty->dev, "%s\n", __func__); - /* pass on to the driver specific version of this function - if it is available */ if (port->serial->type->set_termios) port->serial->type->set_termios(tty, port, old); else @@ -430,26 +436,27 @@ static int serial_break(struct tty_struct *tty, int break_state) { struct usb_serial_port *port = tty->driver_data; - dev_dbg(tty->dev, "%s - port %d\n", __func__, port->number); + dev_dbg(tty->dev, "%s\n", __func__); - /* pass on to the driver specific version of this function - if it is available */ if (port->serial->type->break_ctl) port->serial->type->break_ctl(tty, break_state); + return 0; } static int serial_proc_show(struct seq_file *m, void *v) { struct usb_serial *serial; + struct usb_serial_port *port; int i; char tmp[40]; seq_puts(m, "usbserinfo:1.0 driver:2.0\n"); - for (i = 0; i < SERIAL_TTY_MINORS; ++i) { - serial = usb_serial_get_by_index(i); - if (serial == NULL) + for (i = 0; i < USB_SERIAL_TTY_MINORS; ++i) { + port = usb_serial_port_get_by_minor(i); + if (port == NULL) continue; + serial = port->serial; seq_printf(m, "%d:", i); if (serial->type->driver.owner) @@ -461,7 +468,7 @@ static int serial_proc_show(struct seq_file *m, void *v) le16_to_cpu(serial->dev->descriptor.idVendor), le16_to_cpu(serial->dev->descriptor.idProduct)); seq_printf(m, " num_ports:%d", serial->num_ports); - seq_printf(m, " port:%d", i - serial->minor + 1); + seq_printf(m, " port:%d", port->port_number); usb_make_path(serial->dev, tmp, sizeof(tmp)); seq_printf(m, " path:%s", tmp); @@ -489,7 +496,7 @@ static int serial_tiocmget(struct tty_struct *tty) { struct usb_serial_port *port = tty->driver_data; - dev_dbg(tty->dev, "%s - port %d\n", __func__, port->number); + dev_dbg(tty->dev, "%s\n", __func__); if (port->serial->type->tiocmget) return port->serial->type->tiocmget(tty); @@ -501,7 +508,7 @@ static int serial_tiocmset(struct tty_struct *tty, { struct usb_serial_port *port = tty->driver_data; - dev_dbg(tty->dev, "%s - port %d\n", __func__, port->number); + dev_dbg(tty->dev, "%s\n", __func__); if (port->serial->type->tiocmset) return port->serial->type->tiocmset(tty, set, clear); @@ -513,7 +520,7 @@ static int serial_get_icount(struct tty_struct *tty, { struct usb_serial_port *port = tty->driver_data; - dev_dbg(tty->dev, "%s - port %d\n", __func__, port->number); + dev_dbg(tty->dev, "%s\n", __func__); if (port->serial->type->get_icount) return port->serial->type->get_icount(tty, icount); @@ -535,55 +542,43 @@ static void usb_serial_port_work(struct work_struct *work) { struct usb_serial_port *port = container_of(work, struct usb_serial_port, work); - struct tty_struct *tty; - tty = tty_port_tty_get(&port->port); - if (!tty) - return; + tty_port_tty_wakeup(&port->port); +} - dev_dbg(tty->dev, "%s - port %d\n", __func__, port->number); +static void usb_serial_port_poison_urbs(struct usb_serial_port *port) +{ + int i; - tty_wakeup(tty); - tty_kref_put(tty); + for (i = 0; i < ARRAY_SIZE(port->read_urbs); ++i) + usb_poison_urb(port->read_urbs[i]); + for (i = 0; i < ARRAY_SIZE(port->write_urbs); ++i) + usb_poison_urb(port->write_urbs[i]); + + usb_poison_urb(port->interrupt_in_urb); + usb_poison_urb(port->interrupt_out_urb); } -static void kill_traffic(struct usb_serial_port *port) +static void usb_serial_port_unpoison_urbs(struct usb_serial_port *port) { int i; for (i = 0; i < ARRAY_SIZE(port->read_urbs); ++i) - usb_kill_urb(port->read_urbs[i]); + usb_unpoison_urb(port->read_urbs[i]); for (i = 0; i < ARRAY_SIZE(port->write_urbs); ++i) - usb_kill_urb(port->write_urbs[i]); - /* - * This is tricky. - * Some drivers submit the read_urb in the - * handler for the write_urb or vice versa - * this order determines the order in which - * usb_kill_urb() must be used to reliably - * kill the URBs. As it is unknown here, - * both orders must be used in turn. - * The call below is not redundant. - */ - usb_kill_urb(port->read_urb); - usb_kill_urb(port->interrupt_in_urb); - usb_kill_urb(port->interrupt_out_urb); + usb_unpoison_urb(port->write_urbs[i]); + + usb_unpoison_urb(port->interrupt_in_urb); + usb_unpoison_urb(port->interrupt_out_urb); } -static void port_release(struct device *dev) +static void usb_serial_port_release(struct device *dev) { struct usb_serial_port *port = to_usb_serial_port(dev); int i; dev_dbg(dev, "%s\n", __func__); - /* - * Stop all the traffic before cancelling the work, so that - * nobody will restart it by calling usb_serial_port_softint. - */ - kill_traffic(port); - cancel_work_sync(&port->work); - usb_free_urb(port->interrupt_in_urb); usb_free_urb(port->interrupt_out_urb); for (i = 0; i < ARRAY_SIZE(port->read_urbs); ++i) { @@ -608,16 +603,14 @@ static struct usb_serial *create_serial(struct usb_device *dev, struct usb_serial *serial; serial = kzalloc(sizeof(*serial), GFP_KERNEL); - if (!serial) { - dev_err(&dev->dev, "%s - out of memory\n", __func__); + if (!serial) return NULL; - } serial->dev = usb_get_dev(dev); serial->type = driver; - serial->interface = interface; + serial->interface = usb_get_intf(interface); kref_init(&serial->kref); mutex_init(&serial->disc_mutex); - serial->minor = SERIAL_TTY_NO_MINOR; + serial->minors_reserved = 0; return serial; } @@ -674,7 +667,7 @@ static struct usb_serial_driver *search_serial_device( return NULL; } -static int serial_carrier_raised(struct tty_port *port) +static int serial_port_carrier_raised(struct tty_port *port) { struct usb_serial_port *p = container_of(port, struct usb_serial_port, port); struct usb_serial_driver *drv = p->serial->type; @@ -685,7 +678,7 @@ static int serial_carrier_raised(struct tty_port *port) return 1; } -static void serial_dtr_rts(struct tty_port *port, int on) +static void serial_port_dtr_rts(struct tty_port *port, int on) { struct usb_serial_port *p = container_of(port, struct usb_serial_port, port); struct usb_serial_driver *drv = p->serial->type; @@ -695,10 +688,10 @@ static void serial_dtr_rts(struct tty_port *port, int on) } static const struct tty_port_operations serial_port_ops = { - .carrier_raised = serial_carrier_raised, - .dtr_rts = serial_dtr_rts, - .activate = serial_activate, - .shutdown = serial_down, + .carrier_raised = serial_port_carrier_raised, + .dtr_rts = serial_port_dtr_rts, + .activate = serial_port_activate, + .shutdown = serial_port_shutdown, }; static int usb_serial_probe(struct usb_interface *interface, @@ -716,7 +709,6 @@ static int usb_serial_probe(struct usb_interface *interface, struct usb_endpoint_descriptor *bulk_out_endpoint[MAX_NUM_PORTS]; struct usb_serial_driver *type = NULL; int retval; - unsigned int minor; int buffer_size; int i; int j; @@ -745,7 +737,6 @@ static int usb_serial_probe(struct usb_interface *interface, serial = create_serial(dev, interface, type); if (!serial) { module_put(type->driver.owner); - dev_err(ddev, "%s - out of memory\n", __func__); return -ENOMEM; } @@ -877,7 +868,7 @@ static int usb_serial_probe(struct usb_interface *interface, max_endpoints = max(max_endpoints, (int)serial->num_ports); serial->num_port_pointers = max_endpoints; - dev_dbg(ddev, "setting up %d port structures for this device", max_endpoints); + dev_dbg(ddev, "setting up %d port structure(s)\n", max_endpoints); for (i = 0; i < max_endpoints; ++i) { port = kzalloc(sizeof(struct usb_serial_port), GFP_KERNEL); if (!port) @@ -893,7 +884,7 @@ static int usb_serial_probe(struct usb_interface *interface, port->dev.parent = &interface->dev; port->dev.driver = NULL; port->dev.bus = &usb_serial_bus_type; - port->dev.release = &port_release; + port->dev.release = &usb_serial_port_release; device_initialize(&port->dev); } @@ -909,16 +900,12 @@ static int usb_serial_probe(struct usb_interface *interface, for (j = 0; j < ARRAY_SIZE(port->read_urbs); ++j) { set_bit(j, &port->read_urbs_free); port->read_urbs[j] = usb_alloc_urb(0, GFP_KERNEL); - if (!port->read_urbs[j]) { - dev_err(ddev, "No free urbs available\n"); + if (!port->read_urbs[j]) goto probe_error; - } port->bulk_in_buffers[j] = kmalloc(buffer_size, GFP_KERNEL); - if (!port->bulk_in_buffers[j]) { - dev_err(ddev, "Couldn't allocate bulk_in_buffer\n"); + if (!port->bulk_in_buffers[j]) goto probe_error; - } usb_fill_bulk_urb(port->read_urbs[j], dev, usb_rcvbulkpipe(dev, endpoint->bEndpointAddress), @@ -936,25 +923,20 @@ static int usb_serial_probe(struct usb_interface *interface, port = serial->port[i]; if (kfifo_alloc(&port->write_fifo, PAGE_SIZE, GFP_KERNEL)) goto probe_error; - buffer_size = serial->type->bulk_out_size; - if (!buffer_size) - buffer_size = usb_endpoint_maxp(endpoint); + buffer_size = max_t(int, serial->type->bulk_out_size, + usb_endpoint_maxp(endpoint)); port->bulk_out_size = buffer_size; port->bulk_out_endpointAddress = endpoint->bEndpointAddress; for (j = 0; j < ARRAY_SIZE(port->write_urbs); ++j) { set_bit(j, &port->write_urbs_free); port->write_urbs[j] = usb_alloc_urb(0, GFP_KERNEL); - if (!port->write_urbs[j]) { - dev_err(ddev, "No free urbs available\n"); + if (!port->write_urbs[j]) goto probe_error; - } port->bulk_out_buffers[j] = kmalloc(buffer_size, GFP_KERNEL); - if (!port->bulk_out_buffers[j]) { - dev_err(ddev, "Couldn't allocate bulk_out_buffer\n"); + if (!port->bulk_out_buffers[j]) goto probe_error; - } usb_fill_bulk_urb(port->write_urbs[j], dev, usb_sndbulkpipe(dev, endpoint->bEndpointAddress), @@ -972,19 +954,15 @@ static int usb_serial_probe(struct usb_interface *interface, endpoint = interrupt_in_endpoint[i]; port = serial->port[i]; port->interrupt_in_urb = usb_alloc_urb(0, GFP_KERNEL); - if (!port->interrupt_in_urb) { - dev_err(ddev, "No free urbs available\n"); + if (!port->interrupt_in_urb) goto probe_error; - } buffer_size = usb_endpoint_maxp(endpoint); port->interrupt_in_endpointAddress = endpoint->bEndpointAddress; port->interrupt_in_buffer = kmalloc(buffer_size, GFP_KERNEL); - if (!port->interrupt_in_buffer) { - dev_err(ddev, "Couldn't allocate interrupt_in_buffer\n"); + if (!port->interrupt_in_buffer) goto probe_error; - } usb_fill_int_urb(port->interrupt_in_urb, dev, usb_rcvintpipe(dev, endpoint->bEndpointAddress), @@ -1001,20 +979,16 @@ static int usb_serial_probe(struct usb_interface *interface, endpoint = interrupt_out_endpoint[i]; port = serial->port[i]; port->interrupt_out_urb = usb_alloc_urb(0, GFP_KERNEL); - if (!port->interrupt_out_urb) { - dev_err(ddev, "No free urbs available\n"); + if (!port->interrupt_out_urb) goto probe_error; - } buffer_size = usb_endpoint_maxp(endpoint); port->interrupt_out_size = buffer_size; port->interrupt_out_endpointAddress = endpoint->bEndpointAddress; port->interrupt_out_buffer = kmalloc(buffer_size, GFP_KERNEL); - if (!port->interrupt_out_buffer) { - dev_err(ddev, "Couldn't allocate interrupt_out_buffer\n"); + if (!port->interrupt_out_buffer) goto probe_error; - } usb_fill_int_urb(port->interrupt_out_urb, dev, usb_sndintpipe(dev, endpoint->bEndpointAddress), @@ -1050,17 +1024,16 @@ static int usb_serial_probe(struct usb_interface *interface, */ serial->disconnected = 1; - if (get_free_serial(serial, num_ports, &minor) == NULL) { - dev_err(ddev, "No more free serial devices\n"); + if (allocate_minors(serial, num_ports)) { + dev_err(ddev, "No more free serial minor numbers\n"); goto probe_error; } - serial->minor = minor; /* register all of the individual ports with the driver core */ for (i = 0; i < num_ports; ++i) { port = serial->port[i]; - dev_set_name(&port->dev, "ttyUSB%d", port->number); - dev_dbg(ddev, "registering %s", dev_name(&port->dev)); + dev_set_name(&port->dev, "ttyUSB%d", port->minor); + dev_dbg(ddev, "registering %s\n", dev_name(&port->dev)); device_enable_async_suspend(&port->dev); retval = device_add(&port->dev); @@ -1070,7 +1043,7 @@ static int usb_serial_probe(struct usb_interface *interface, serial->disconnected = 0; - usb_serial_console_init(minor); + usb_serial_console_init(serial->port[0]->minor); exit: module_put(type->driver.owner); return 0; @@ -1087,6 +1060,7 @@ static void usb_serial_disconnect(struct usb_interface *interface) struct usb_serial *serial = usb_get_intfdata(interface); struct device *dev = &interface->dev; struct usb_serial_port *port; + struct tty_struct *tty; usb_serial_console_disconnect(serial); @@ -1097,19 +1071,19 @@ static void usb_serial_disconnect(struct usb_interface *interface) for (i = 0; i < serial->num_ports; ++i) { port = serial->port[i]; - if (port) { - struct tty_struct *tty = tty_port_tty_get(&port->port); - if (tty) { - tty_vhangup(tty); - tty_kref_put(tty); - } - kill_traffic(port); - cancel_work_sync(&port->work); - if (device_is_registered(&port->dev)) - device_del(&port->dev); + tty = tty_port_tty_get(&port->port); + if (tty) { + tty_vhangup(tty); + tty_kref_put(tty); } + usb_serial_port_poison_urbs(port); + wake_up_interruptible(&port->port.delta_msr_wait); + cancel_work_sync(&port->work); + if (device_is_registered(&port->dev)) + device_del(&port->dev); } - serial->type->disconnect(serial); + if (serial->type->disconnect) + serial->type->disconnect(serial); /* let the last holder of this object cause it to be cleaned up */ usb_serial_put(serial); @@ -1119,11 +1093,15 @@ static void usb_serial_disconnect(struct usb_interface *interface) int usb_serial_suspend(struct usb_interface *intf, pm_message_t message) { struct usb_serial *serial = usb_get_intfdata(intf); - struct usb_serial_port *port; int i, r = 0; serial->suspending = 1; + /* + * serial->type->suspend() MUST return 0 in system sleep context, + * otherwise, the resume callback has to recover device from + * previous suspend failure. + */ if (serial->type->suspend) { r = serial->type->suspend(serial, message); if (r < 0) { @@ -1132,22 +1110,28 @@ int usb_serial_suspend(struct usb_interface *intf, pm_message_t message) } } - for (i = 0; i < serial->num_ports; ++i) { - port = serial->port[i]; - if (port) - kill_traffic(port); - } - + for (i = 0; i < serial->num_ports; ++i) + usb_serial_port_poison_urbs(serial->port[i]); err_out: return r; } EXPORT_SYMBOL(usb_serial_suspend); +static void usb_serial_unpoison_port_urbs(struct usb_serial *serial) +{ + int i; + + for (i = 0; i < serial->num_ports; ++i) + usb_serial_port_unpoison_urbs(serial->port[i]); +} + int usb_serial_resume(struct usb_interface *intf) { struct usb_serial *serial = usb_get_intfdata(intf); int rv; + usb_serial_unpoison_port_urbs(serial); + serial->suspending = 0; if (serial->type->resume) rv = serial->type->resume(serial); @@ -1163,10 +1147,12 @@ static int usb_serial_reset_resume(struct usb_interface *intf) struct usb_serial *serial = usb_get_intfdata(intf); int rv; + usb_serial_unpoison_port_urbs(serial); + serial->suspending = 0; - if (serial->type->reset_resume) + if (serial->type->reset_resume) { rv = serial->type->reset_resume(serial); - else { + } else { rv = -EOPNOTSUPP; intf->needs_binding = 1; } @@ -1186,6 +1172,7 @@ static const struct tty_operations serial_ops = { .unthrottle = serial_unthrottle, .break_ctl = serial_break, .chars_in_buffer = serial_chars_in_buffer, + .wait_until_sent = serial_wait_until_sent, .tiocmget = serial_tiocmget, .tiocmset = serial_tiocmset, .get_icount = serial_get_icount, @@ -1210,17 +1197,13 @@ static struct usb_driver usb_serial_driver = { static int __init usb_serial_init(void) { - int i; int result; - usb_serial_tty_driver = alloc_tty_driver(SERIAL_TTY_MINORS); + usb_serial_tty_driver = alloc_tty_driver(USB_SERIAL_TTY_MINORS); if (!usb_serial_tty_driver) return -ENOMEM; /* Initialize our global data */ - for (i = 0; i < SERIAL_TTY_MINORS; ++i) - serial_table[i] = NULL; - result = bus_register(&usb_serial_bus_type); if (result) { pr_err("%s - registering bus driver failed\n", __func__); @@ -1229,7 +1212,7 @@ static int __init usb_serial_init(void) usb_serial_tty_driver->driver_name = "usbserial"; usb_serial_tty_driver->name = "ttyUSB"; - usb_serial_tty_driver->major = SERIAL_TTY_MAJOR; + usb_serial_tty_driver->major = USB_SERIAL_TTY_MAJOR; usb_serial_tty_driver->minor_start = 0; usb_serial_tty_driver->type = TTY_DRIVER_TYPE_SERIAL; usb_serial_tty_driver->subtype = SERIAL_TYPE_NORMAL; @@ -1299,22 +1282,22 @@ module_exit(usb_serial_exit); do { \ if (!type->function) { \ type->function = usb_serial_generic_##function; \ - pr_debug("Had to override the " #function \ - " usb serial operation with the generic one.");\ - } \ + pr_debug("%s: using generic " #function "\n", \ + type->driver.name); \ + } \ } while (0) -static void fixup_generic(struct usb_serial_driver *device) +static void usb_serial_operations_init(struct usb_serial_driver *device) { set_to_generic_if_null(device, open); set_to_generic_if_null(device, write); set_to_generic_if_null(device, close); set_to_generic_if_null(device, write_room); set_to_generic_if_null(device, chars_in_buffer); + if (device->tx_empty) + set_to_generic_if_null(device, wait_until_sent); set_to_generic_if_null(device, read_bulk_callback); set_to_generic_if_null(device, write_bulk_callback); - set_to_generic_if_null(device, disconnect); - set_to_generic_if_null(device, release); set_to_generic_if_null(device, process_read_urb); set_to_generic_if_null(device, prepare_write_buffer); } @@ -1326,8 +1309,6 @@ static int usb_serial_register(struct usb_serial_driver *driver) if (usb_disabled()) return -ENODEV; - fixup_generic(driver); - if (!driver->description) driver->description = driver->driver.name; if (!driver->usb_driver) { @@ -1336,6 +1317,8 @@ static int usb_serial_register(struct usb_serial_driver *driver) return -EINVAL; } + usb_serial_operations_init(driver); + /* Add this device to our list of devices */ mutex_lock(&table_lock); list_add(&driver->driver_list, &usb_serial_driver_list); @@ -1344,9 +1327,9 @@ static int usb_serial_register(struct usb_serial_driver *driver) if (retval) { pr_err("problem %d when registering driver %s\n", retval, driver->description); list_del(&driver->driver_list); - } else + } else { pr_info("USB Serial support registered for %s\n", driver->description); - + } mutex_unlock(&table_lock); return retval; } @@ -1354,10 +1337,12 @@ static int usb_serial_register(struct usb_serial_driver *driver) static void usb_serial_deregister(struct usb_serial_driver *device) { pr_info("USB Serial deregistering driver %s\n", device->description); + mutex_lock(&table_lock); list_del(&device->driver_list); - usb_serial_bus_deregister(device); mutex_unlock(&table_lock); + + usb_serial_bus_deregister(device); } /** @@ -1453,7 +1438,6 @@ void usb_serial_deregister_drivers(struct usb_serial_driver *const serial_driver } EXPORT_SYMBOL_GPL(usb_serial_deregister_drivers); -/* Module information */ MODULE_AUTHOR(DRIVER_AUTHOR); MODULE_DESCRIPTION(DRIVER_DESC); MODULE_LICENSE("GPL"); diff --git a/drivers/usb/serial/usb-wwan.h b/drivers/usb/serial/usb-wwan.h index 684739b8efd..f22dff58b58 100644 --- a/drivers/usb/serial/usb-wwan.h +++ b/drivers/usb/serial/usb-wwan.h @@ -11,15 +11,11 @@ extern void usb_wwan_close(struct usb_serial_port *port); extern int usb_wwan_port_probe(struct usb_serial_port *port); extern int usb_wwan_port_remove(struct usb_serial_port *port); extern int usb_wwan_write_room(struct tty_struct *tty); -extern void usb_wwan_set_termios(struct tty_struct *tty, - struct usb_serial_port *port, - struct ktermios *old); extern int usb_wwan_tiocmget(struct tty_struct *tty); extern int usb_wwan_tiocmset(struct tty_struct *tty, unsigned int set, unsigned int clear); extern int usb_wwan_ioctl(struct tty_struct *tty, unsigned int cmd, unsigned long arg); -extern int usb_wwan_send_setup(struct usb_serial_port *port); extern int usb_wwan_write(struct tty_struct *tty, struct usb_serial_port *port, const unsigned char *buf, int count); extern int usb_wwan_chars_in_buffer(struct tty_struct *tty); @@ -39,6 +35,7 @@ struct usb_wwan_intf_private { spinlock_t susp_lock; unsigned int suspended:1; int in_flight; + unsigned int open_ports; int (*send_setup) (struct usb_serial_port *port); void *private; }; @@ -51,7 +48,6 @@ struct usb_wwan_port_private { struct urb *out_urbs[N_OUT_URB]; u8 *out_buffer[N_OUT_URB]; unsigned long out_busy; /* Bit vector of URBs in use */ - int opened; struct usb_anchor delayed; /* Settings for the port */ diff --git a/drivers/usb/serial/usb_debug.c b/drivers/usb/serial/usb_debug.c index 5760f97ee50..ca2fa5bbe17 100644 --- a/drivers/usb/serial/usb_debug.c +++ b/drivers/usb/serial/usb_debug.c @@ -10,7 +10,6 @@ #include <linux/gfp.h> #include <linux/kernel.h> -#include <linux/init.h> #include <linux/tty.h> #include <linux/module.h> #include <linux/usb.h> diff --git a/drivers/usb/serial/usb_wwan.c b/drivers/usb/serial/usb_wwan.c index 01c94aada56..2f805cb386a 100644 --- a/drivers/usb/serial/usb_wwan.c +++ b/drivers/usb/serial/usb_wwan.c @@ -38,38 +38,22 @@ void usb_wwan_dtr_rts(struct usb_serial_port *port, int on) { - struct usb_serial *serial = port->serial; struct usb_wwan_port_private *portdata; struct usb_wwan_intf_private *intfdata; - intfdata = port->serial->private; + intfdata = usb_get_serial_data(port->serial); if (!intfdata->send_setup) return; portdata = usb_get_serial_port_data(port); - mutex_lock(&serial->disc_mutex); + /* FIXME: locking */ portdata->rts_state = on; portdata->dtr_state = on; - if (serial->dev) - intfdata->send_setup(port); - mutex_unlock(&serial->disc_mutex); -} -EXPORT_SYMBOL(usb_wwan_dtr_rts); - -void usb_wwan_set_termios(struct tty_struct *tty, - struct usb_serial_port *port, - struct ktermios *old_termios) -{ - struct usb_wwan_intf_private *intfdata = port->serial->private; - - /* Doesn't support option setting */ - tty_termios_copy_hw(&tty->termios, old_termios); - if (intfdata->send_setup) - intfdata->send_setup(port); + intfdata->send_setup(port); } -EXPORT_SYMBOL(usb_wwan_set_termios); +EXPORT_SYMBOL(usb_wwan_dtr_rts); int usb_wwan_tiocmget(struct tty_struct *tty) { @@ -98,7 +82,7 @@ int usb_wwan_tiocmset(struct tty_struct *tty, struct usb_wwan_intf_private *intfdata; portdata = usb_get_serial_port_data(port); - intfdata = port->serial->private; + intfdata = usb_get_serial_data(port->serial); if (!intfdata->send_setup) return -EINVAL; @@ -126,8 +110,8 @@ static int get_serial_info(struct usb_serial_port *port, return -EFAULT; memset(&tmp, 0, sizeof(tmp)); - tmp.line = port->serial->minor; - tmp.port = port->number; + tmp.line = port->minor; + tmp.port = port->port_number; tmp.baud_base = tty_get_baud_rate(port->port.tty); tmp.close_delay = port->port.close_delay / 10; tmp.closing_wait = port->port.closing_wait == ASYNC_CLOSING_WAIT_NONE ? @@ -194,7 +178,6 @@ int usb_wwan_ioctl(struct tty_struct *tty, } EXPORT_SYMBOL(usb_wwan_ioctl); -/* Write */ int usb_wwan_write(struct tty_struct *tty, struct usb_serial_port *port, const unsigned char *buf, int count) { @@ -207,7 +190,7 @@ int usb_wwan_write(struct tty_struct *tty, struct usb_serial_port *port, unsigned long flags; portdata = usb_get_serial_port_data(port); - intfdata = port->serial->private; + intfdata = usb_get_serial_data(port->serial); dev_dbg(&port->dev, "%s: write (%d chars)\n", __func__, count); @@ -230,8 +213,10 @@ int usb_wwan_write(struct tty_struct *tty, struct usb_serial_port *port, usb_pipeendpoint(this_urb->pipe), i); err = usb_autopm_get_interface_async(port->serial->interface); - if (err < 0) + if (err < 0) { + clear_bit(i, &portdata->out_busy); break; + } /* send the data */ memcpy(this_urb->transfer_buffer, buf, todo); @@ -246,9 +231,9 @@ int usb_wwan_write(struct tty_struct *tty, struct usb_serial_port *port, spin_unlock_irqrestore(&intfdata->susp_lock, flags); err = usb_submit_urb(this_urb, GFP_ATOMIC); if (err) { - dev_dbg(&port->dev, - "usb_submit_urb %p (write bulk) failed (%d)\n", - this_urb, err); + dev_err(&port->dev, + "%s: submit urb %d failed: %d\n", + __func__, i, err); clear_bit(i, &portdata->out_busy); spin_lock_irqsave(&intfdata->susp_lock, flags); intfdata->in_flight--; @@ -275,7 +260,6 @@ static void usb_wwan_indat_callback(struct urb *urb) int err; int endpoint; struct usb_serial_port *port; - struct tty_struct *tty; struct device *dev; unsigned char *data = urb->transfer_buffer; int status = urb->status; @@ -288,28 +272,24 @@ static void usb_wwan_indat_callback(struct urb *urb) dev_dbg(dev, "%s: nonzero status: %d on endpoint %02x.\n", __func__, status, endpoint); } else { - tty = tty_port_tty_get(&port->port); - if (tty) { - if (urb->actual_length) { - tty_insert_flip_string(tty, data, - urb->actual_length); - tty_flip_buffer_push(tty); - } else - dev_dbg(dev, "%s: empty read urb received\n", __func__); - tty_kref_put(tty); - } - - /* Resubmit urb so we continue receiving */ - err = usb_submit_urb(urb, GFP_ATOMIC); - if (err) { - if (err != -EPERM) { - dev_err(dev, "%s: resubmit read urb failed. (%d)\n", __func__, err); - /* busy also in error unless we are killed */ - usb_mark_last_busy(port->serial->dev); - } - } else { + if (urb->actual_length) { + tty_insert_flip_string(&port->port, data, + urb->actual_length); + tty_flip_buffer_push(&port->port); + } else + dev_dbg(dev, "%s: empty read urb received\n", __func__); + } + /* Resubmit urb so we continue receiving */ + err = usb_submit_urb(urb, GFP_ATOMIC); + if (err) { + if (err != -EPERM) { + dev_err(dev, "%s: resubmit read urb failed. (%d)\n", + __func__, err); + /* busy also in error unless we are killed */ usb_mark_last_busy(port->serial->dev); } + } else { + usb_mark_last_busy(port->serial->dev); } } @@ -321,7 +301,7 @@ static void usb_wwan_outdat_callback(struct urb *urb) int i; port = urb->context; - intfdata = port->serial->private; + intfdata = usb_get_serial_data(port->serial); usb_serial_port_softint(port); usb_autopm_put_interface_async(port->serial->interface); @@ -332,7 +312,7 @@ static void usb_wwan_outdat_callback(struct urb *urb) for (i = 0; i < N_OUT_URB; ++i) { if (portdata->out_urbs[i] == urb) { - smp_mb__before_clear_bit(); + smp_mb__before_atomic(); clear_bit(i, &portdata->out_busy); break; } @@ -391,7 +371,15 @@ int usb_wwan_open(struct tty_struct *tty, struct usb_serial_port *port) struct urb *urb; portdata = usb_get_serial_port_data(port); - intfdata = serial->private; + intfdata = usb_get_serial_data(serial); + + if (port->interrupt_in_urb) { + err = usb_submit_urb(port->interrupt_in_urb, GFP_KERNEL); + if (err) { + dev_err(&port->dev, "%s: submit int urb failed: %d\n", + __func__, err); + } + } /* Start reading from the IN endpoint */ for (i = 0; i < N_IN_URB; i++) { @@ -400,17 +388,15 @@ int usb_wwan_open(struct tty_struct *tty, struct usb_serial_port *port) continue; err = usb_submit_urb(urb, GFP_KERNEL); if (err) { - dev_dbg(&port->dev, "%s: submit urb %d failed (%d) %d\n", - __func__, i, err, urb->transfer_buffer_length); + dev_err(&port->dev, + "%s: submit read urb %d failed: %d\n", + __func__, i, err); } } - if (intfdata->send_setup) - intfdata->send_setup(port); - - serial->interface->needs_remote_wakeup = 1; spin_lock_irq(&intfdata->susp_lock); - portdata->opened = 1; + if (++intfdata->open_ports == 1) + serial->interface->needs_remote_wakeup = 1; spin_unlock_irq(&intfdata->susp_lock); /* this balances a get in the generic USB serial code */ usb_autopm_put_interface(serial->interface); @@ -419,33 +405,56 @@ int usb_wwan_open(struct tty_struct *tty, struct usb_serial_port *port) } EXPORT_SYMBOL(usb_wwan_open); +static void unbusy_queued_urb(struct urb *urb, + struct usb_wwan_port_private *portdata) +{ + int i; + + for (i = 0; i < N_OUT_URB; i++) { + if (urb == portdata->out_urbs[i]) { + clear_bit(i, &portdata->out_busy); + break; + } + } +} + void usb_wwan_close(struct usb_serial_port *port) { int i; struct usb_serial *serial = port->serial; struct usb_wwan_port_private *portdata; - struct usb_wwan_intf_private *intfdata = port->serial->private; + struct usb_wwan_intf_private *intfdata = usb_get_serial_data(serial); + struct urb *urb; portdata = usb_get_serial_port_data(port); - if (serial->dev) { - /* Stop reading/writing urbs */ - spin_lock_irq(&intfdata->susp_lock); - portdata->opened = 0; - spin_unlock_irq(&intfdata->susp_lock); - - for (i = 0; i < N_IN_URB; i++) - usb_kill_urb(portdata->in_urbs[i]); - for (i = 0; i < N_OUT_URB; i++) - usb_kill_urb(portdata->out_urbs[i]); - /* balancing - important as an error cannot be handled*/ - usb_autopm_get_interface_no_resume(serial->interface); + /* + * Need to take susp_lock to make sure port is not already being + * resumed, but no need to hold it due to ASYNC_INITIALIZED. + */ + spin_lock_irq(&intfdata->susp_lock); + if (--intfdata->open_ports == 0) serial->interface->needs_remote_wakeup = 0; + spin_unlock_irq(&intfdata->susp_lock); + + for (;;) { + urb = usb_get_from_anchor(&portdata->delayed); + if (!urb) + break; + unbusy_queued_urb(urb, portdata); + usb_autopm_put_interface_async(serial->interface); } + + for (i = 0; i < N_IN_URB; i++) + usb_kill_urb(portdata->in_urbs[i]); + for (i = 0; i < N_OUT_URB; i++) + usb_kill_urb(portdata->out_urbs[i]); + usb_kill_urb(port->interrupt_in_urb); + + usb_autopm_get_interface_no_resume(serial->interface); } EXPORT_SYMBOL(usb_wwan_close); -/* Helper functions used by usb_wwan_setup_urbs */ static struct urb *usb_wwan_setup_urb(struct usb_serial_port *port, int endpoint, int dir, void *ctx, char *buf, int len, @@ -455,14 +464,9 @@ static struct urb *usb_wwan_setup_urb(struct usb_serial_port *port, struct urb *urb; urb = usb_alloc_urb(0, GFP_KERNEL); /* No ISO */ - if (urb == NULL) { - dev_dbg(&serial->interface->dev, - "%s: alloc for endpoint %d failed.\n", __func__, - endpoint); + if (!urb) return NULL; - } - /* Fill URB using supplied data. */ usb_fill_bulk_urb(urb, serial->dev, usb_sndbulkpipe(serial->dev, endpoint) | dir, buf, len, callback, ctx); @@ -475,9 +479,11 @@ int usb_wwan_port_probe(struct usb_serial_port *port) struct usb_wwan_port_private *portdata; struct urb *urb; u8 *buffer; - int err; int i; + if (!port->bulk_in_size || !port->bulk_out_size) + return -ENODEV; + portdata = kzalloc(sizeof(*portdata), GFP_KERNEL); if (!portdata) return -ENOMEM; @@ -485,9 +491,6 @@ int usb_wwan_port_probe(struct usb_serial_port *port) init_usb_anchor(&portdata->delayed); for (i = 0; i < N_IN_URB; i++) { - if (!port->bulk_in_size) - break; - buffer = (u8 *)__get_free_page(GFP_KERNEL); if (!buffer) goto bail_out_error; @@ -501,9 +504,6 @@ int usb_wwan_port_probe(struct usb_serial_port *port) } for (i = 0; i < N_OUT_URB; i++) { - if (!port->bulk_out_size) - break; - buffer = kmalloc(OUT_BUFLEN, GFP_KERNEL); if (!buffer) goto bail_out_error2; @@ -518,13 +518,6 @@ int usb_wwan_port_probe(struct usb_serial_port *port) usb_set_serial_port_data(port, portdata); - if (port->interrupt_in_urb) { - err = usb_submit_urb(port->interrupt_in_urb, GFP_KERNEL); - if (err) - dev_dbg(&port->dev, "%s: submit irq_in urb failed %d\n", - __func__, err); - } - return 0; bail_out_error2: @@ -551,32 +544,28 @@ int usb_wwan_port_remove(struct usb_serial_port *port) portdata = usb_get_serial_port_data(port); usb_set_serial_port_data(port, NULL); - /* Stop reading/writing urbs and free them */ for (i = 0; i < N_IN_URB; i++) { - usb_kill_urb(portdata->in_urbs[i]); usb_free_urb(portdata->in_urbs[i]); free_page((unsigned long)portdata->in_buffer[i]); } for (i = 0; i < N_OUT_URB; i++) { - usb_kill_urb(portdata->out_urbs[i]); usb_free_urb(portdata->out_urbs[i]); kfree(portdata->out_buffer[i]); } - /* Now free port private data */ kfree(portdata); + return 0; } EXPORT_SYMBOL(usb_wwan_port_remove); #ifdef CONFIG_PM -static void stop_read_write_urbs(struct usb_serial *serial) +static void stop_urbs(struct usb_serial *serial) { int i, j; struct usb_serial_port *port; struct usb_wwan_port_private *portdata; - /* Stop reading/writing urbs */ for (i = 0; i < serial->num_ports; ++i) { port = serial->port[i]; portdata = usb_get_serial_port_data(port); @@ -586,123 +575,117 @@ static void stop_read_write_urbs(struct usb_serial *serial) usb_kill_urb(portdata->in_urbs[j]); for (j = 0; j < N_OUT_URB; j++) usb_kill_urb(portdata->out_urbs[j]); + usb_kill_urb(port->interrupt_in_urb); } } int usb_wwan_suspend(struct usb_serial *serial, pm_message_t message) { - struct usb_wwan_intf_private *intfdata = serial->private; - int b; + struct usb_wwan_intf_private *intfdata = usb_get_serial_data(serial); + spin_lock_irq(&intfdata->susp_lock); if (PMSG_IS_AUTO(message)) { - spin_lock_irq(&intfdata->susp_lock); - b = intfdata->in_flight; - spin_unlock_irq(&intfdata->susp_lock); - - if (b) + if (intfdata->in_flight) { + spin_unlock_irq(&intfdata->susp_lock); return -EBUSY; + } } - - spin_lock_irq(&intfdata->susp_lock); intfdata->suspended = 1; spin_unlock_irq(&intfdata->susp_lock); - stop_read_write_urbs(serial); + + stop_urbs(serial); return 0; } EXPORT_SYMBOL(usb_wwan_suspend); -static void unbusy_queued_urb(struct urb *urb, struct usb_wwan_port_private *portdata) +/* Caller must hold susp_lock. */ +static int usb_wwan_submit_delayed_urbs(struct usb_serial_port *port) { - int i; - - for (i = 0; i < N_OUT_URB; i++) { - if (urb == portdata->out_urbs[i]) { - clear_bit(i, &portdata->out_busy); - break; - } - } -} - -static void play_delayed(struct usb_serial_port *port) -{ - struct usb_wwan_intf_private *data; + struct usb_serial *serial = port->serial; + struct usb_wwan_intf_private *data = usb_get_serial_data(serial); struct usb_wwan_port_private *portdata; struct urb *urb; + int err_count = 0; int err; portdata = usb_get_serial_port_data(port); - data = port->serial->private; - while ((urb = usb_get_from_anchor(&portdata->delayed))) { - err = usb_submit_urb(urb, GFP_ATOMIC); - if (!err) { - data->in_flight++; - } else { - /* we have to throw away the rest */ - do { - unbusy_queued_urb(urb, portdata); - usb_autopm_put_interface_no_suspend(port->serial->interface); - } while ((urb = usb_get_from_anchor(&portdata->delayed))); + + for (;;) { + urb = usb_get_from_anchor(&portdata->delayed); + if (!urb) break; + + err = usb_submit_urb(urb, GFP_ATOMIC); + if (err) { + dev_err(&port->dev, "%s: submit urb failed: %d\n", + __func__, err); + err_count++; + unbusy_queued_urb(urb, portdata); + usb_autopm_put_interface_async(serial->interface); + continue; } + data->in_flight++; } + + if (err_count) + return -EIO; + + return 0; } int usb_wwan_resume(struct usb_serial *serial) { int i, j; struct usb_serial_port *port; - struct usb_wwan_intf_private *intfdata = serial->private; + struct usb_wwan_intf_private *intfdata = usb_get_serial_data(serial); struct usb_wwan_port_private *portdata; struct urb *urb; - int err = 0; + int err; + int err_count = 0; - /* get the interrupt URBs resubmitted unconditionally */ + spin_lock_irq(&intfdata->susp_lock); for (i = 0; i < serial->num_ports; i++) { port = serial->port[i]; - if (!port->interrupt_in_urb) { - dev_dbg(&port->dev, "%s: No interrupt URB for port\n", __func__); + + if (!test_bit(ASYNCB_INITIALIZED, &port->port.flags)) continue; - } - err = usb_submit_urb(port->interrupt_in_urb, GFP_NOIO); - dev_dbg(&port->dev, "Submitted interrupt URB for port (result %d)\n", err); - if (err < 0) { - dev_err(&port->dev, "%s: Error %d for interrupt URB\n", - __func__, err); - goto err_out; - } - } - for (i = 0; i < serial->num_ports; i++) { - /* walk all ports */ - port = serial->port[i]; portdata = usb_get_serial_port_data(port); - /* skip closed ports */ - spin_lock_irq(&intfdata->susp_lock); - if (!portdata || !portdata->opened) { - spin_unlock_irq(&intfdata->susp_lock); - continue; + if (port->interrupt_in_urb) { + err = usb_submit_urb(port->interrupt_in_urb, + GFP_ATOMIC); + if (err) { + dev_err(&port->dev, + "%s: submit int urb failed: %d\n", + __func__, err); + err_count++; + } } + err = usb_wwan_submit_delayed_urbs(port); + if (err) + err_count++; + for (j = 0; j < N_IN_URB; j++) { urb = portdata->in_urbs[j]; err = usb_submit_urb(urb, GFP_ATOMIC); if (err < 0) { - dev_err(&port->dev, "%s: Error %d for bulk URB %d\n", - __func__, err, i); - spin_unlock_irq(&intfdata->susp_lock); - goto err_out; + dev_err(&port->dev, + "%s: submit read urb %d failed: %d\n", + __func__, i, err); + err_count++; } } - play_delayed(port); - spin_unlock_irq(&intfdata->susp_lock); } - spin_lock_irq(&intfdata->susp_lock); intfdata->suspended = 0; spin_unlock_irq(&intfdata->susp_lock); -err_out: - return err; + + if (err_count) + return -EIO; + + return 0; } EXPORT_SYMBOL(usb_wwan_resume); #endif diff --git a/drivers/usb/serial/visor.c b/drivers/usb/serial/visor.c index 1129aa73c23..bf2bd40e5f2 100644 --- a/drivers/usb/serial/visor.c +++ b/drivers/usb/serial/visor.c @@ -16,7 +16,6 @@ #include <linux/kernel.h> #include <linux/errno.h> -#include <linux/init.h> #include <linux/slab.h> #include <linux/tty.h> #include <linux/tty_driver.h> @@ -51,7 +50,7 @@ static int palm_os_3_probe(struct usb_serial *serial, static int palm_os_4_probe(struct usb_serial *serial, const struct usb_device_id *id); -static struct usb_device_id id_table [] = { +static const struct usb_device_id id_table[] = { { USB_DEVICE(HANDSPRING_VENDOR_ID, HANDSPRING_VISOR_ID), .driver_info = (kernel_ulong_t)&palm_os_3_probe }, { USB_DEVICE(HANDSPRING_VENDOR_ID, HANDSPRING_TREO_ID), @@ -113,18 +112,18 @@ static struct usb_device_id id_table [] = { { } /* Terminating entry */ }; -static struct usb_device_id clie_id_5_table [] = { +static const struct usb_device_id clie_id_5_table[] = { { USB_DEVICE(SONY_VENDOR_ID, SONY_CLIE_UX50_ID), .driver_info = (kernel_ulong_t)&palm_os_4_probe }, { } /* Terminating entry */ }; -static struct usb_device_id clie_id_3_5_table [] = { +static const struct usb_device_id clie_id_3_5_table[] = { { USB_DEVICE(SONY_VENDOR_ID, SONY_CLIE_3_5_ID) }, { } /* Terminating entry */ }; -static struct usb_device_id id_table_combined [] = { +static const struct usb_device_id id_table_combined[] = { { USB_DEVICE(HANDSPRING_VENDOR_ID, HANDSPRING_VISOR_ID) }, { USB_DEVICE(HANDSPRING_VENDOR_ID, HANDSPRING_TREO_ID) }, { USB_DEVICE(HANDSPRING_VENDOR_ID, HANDSPRING_TREO600_ID) }, @@ -257,24 +256,18 @@ static void visor_close(struct usb_serial_port *port) { unsigned char *transfer_buffer; - /* shutdown our urbs */ usb_serial_generic_close(port); usb_kill_urb(port->interrupt_in_urb); - mutex_lock(&port->serial->disc_mutex); - if (!port->serial->disconnected) { - /* Try to send shutdown message, unless the device is gone */ - transfer_buffer = kmalloc(0x12, GFP_KERNEL); - if (transfer_buffer) { - usb_control_msg(port->serial->dev, + transfer_buffer = kmalloc(0x12, GFP_KERNEL); + if (!transfer_buffer) + return; + usb_control_msg(port->serial->dev, usb_rcvctrlpipe(port->serial->dev, 0), VISOR_CLOSE_NOTIFICATION, 0xc2, 0x0000, 0x0000, transfer_buffer, 0x12, 300); - kfree(transfer_buffer); - } - } - mutex_unlock(&port->serial->disc_mutex); + kfree(transfer_buffer); } static void visor_read_int_callback(struct urb *urb) @@ -330,11 +323,8 @@ static int palm_os_3_probe(struct usb_serial *serial, int num_ports = 0; transfer_buffer = kmalloc(sizeof(*connection_info), GFP_KERNEL); - if (!transfer_buffer) { - dev_err(dev, "%s - kmalloc(%Zd) failed.\n", __func__, - sizeof(*connection_info)); + if (!transfer_buffer) return -ENOMEM; - } /* send a get connection info request */ retval = usb_control_msg(serial->dev, @@ -425,11 +415,8 @@ static int palm_os_4_probe(struct usb_serial *serial, int retval; transfer_buffer = kmalloc(sizeof(*connection_info), GFP_KERNEL); - if (!transfer_buffer) { - dev_err(dev, "%s - kmalloc(%Zd) failed.\n", __func__, - sizeof(*connection_info)); + if (!transfer_buffer) return -ENOMEM; - } retval = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0), @@ -566,10 +553,19 @@ static int treo_attach(struct usb_serial *serial) */ #define COPY_PORT(dest, src) \ do { \ + int i; \ + \ + for (i = 0; i < ARRAY_SIZE(src->read_urbs); ++i) { \ + dest->read_urbs[i] = src->read_urbs[i]; \ + dest->read_urbs[i]->context = dest; \ + dest->bulk_in_buffers[i] = src->bulk_in_buffers[i]; \ + } \ dest->read_urb = src->read_urb; \ dest->bulk_in_endpointAddress = src->bulk_in_endpointAddress;\ dest->bulk_in_buffer = src->bulk_in_buffer; \ + dest->bulk_in_size = src->bulk_in_size; \ dest->interrupt_in_urb = src->interrupt_in_urb; \ + dest->interrupt_in_urb->context = dest; \ dest->interrupt_in_endpointAddress = \ src->interrupt_in_endpointAddress;\ dest->interrupt_in_buffer = src->interrupt_in_buffer; \ diff --git a/drivers/usb/serial/visor.h b/drivers/usb/serial/visor.h index 88db4d06aef..4c456dd69ce 100644 --- a/drivers/usb/serial/visor.h +++ b/drivers/usb/serial/visor.h @@ -136,7 +136,7 @@ struct visor_connection_info { * connections.end_point_info is non-zero. If value is 0, then * connections.port contains the endpoint number, which is the same for in * and out. - * @port_function_id: contains the creator id of the applicaton that opened + * @port_function_id: contains the creator id of the application that opened * this connection. * @port: contains the in/out endpoint number. Is 0 if in and out endpoint * numbers are different. diff --git a/drivers/usb/serial/vivopay-serial.c b/drivers/usb/serial/vivopay-serial.c deleted file mode 100644 index 6299526ff8c..00000000000 --- a/drivers/usb/serial/vivopay-serial.c +++ /dev/null @@ -1,43 +0,0 @@ -/* - * Copyright (C) 2001-2005 Greg Kroah-Hartman (greg@kroah.com) - * Copyright (C) 2009 Outpost Embedded, LLC - */ - -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/tty.h> -#include <linux/module.h> -#include <linux/usb.h> -#include <linux/usb/serial.h> - -#define DRIVER_DESC "ViVOpay USB Serial Driver" - -#define VIVOPAY_VENDOR_ID 0x1d5f - - -static struct usb_device_id id_table [] = { - /* ViVOpay 8800 */ - { USB_DEVICE(VIVOPAY_VENDOR_ID, 0x1004) }, - { }, -}; - -MODULE_DEVICE_TABLE(usb, id_table); - -static struct usb_serial_driver vivopay_serial_device = { - .driver = { - .owner = THIS_MODULE, - .name = "vivopay-serial", - }, - .id_table = id_table, - .num_ports = 1, -}; - -static struct usb_serial_driver * const serial_drivers[] = { - &vivopay_serial_device, NULL -}; - -module_usb_serial_driver(serial_drivers, id_table); - -MODULE_AUTHOR("Forest Bond <forest.bond@outpostembedded.com>"); -MODULE_DESCRIPTION(DRIVER_DESC); -MODULE_LICENSE("GPL"); diff --git a/drivers/usb/serial/whiteheat.c b/drivers/usb/serial/whiteheat.c index b9fca3586d7..e62f2dff8b7 100644 --- a/drivers/usb/serial/whiteheat.c +++ b/drivers/usb/serial/whiteheat.c @@ -18,7 +18,6 @@ #include <linux/kernel.h> #include <linux/errno.h> -#include <linux/init.h> #include <linux/slab.h> #include <linux/tty.h> #include <linux/tty_driver.h> @@ -288,12 +287,8 @@ static int whiteheat_attach(struct usb_serial *serial) command_info = kmalloc(sizeof(struct whiteheat_command_private), GFP_KERNEL); - if (command_info == NULL) { - dev_err(&serial->dev->dev, - "%s: Out of memory for port structures\n", - serial->type->description); + if (!command_info) goto no_command_private; - } mutex_init(&command_info->mutex); command_info->port_running = 0; @@ -455,14 +450,12 @@ static int whiteheat_ioctl(struct tty_struct *tty, struct serial_struct serstruct; void __user *user_arg = (void __user *)arg; - dev_dbg(&port->dev, "%s - cmd 0x%.4x\n", __func__, cmd); - switch (cmd) { case TIOCGSERIAL: memset(&serstruct, 0, sizeof(serstruct)); serstruct.type = PORT_16654; - serstruct.line = port->serial->minor; - serstruct.port = port->number; + serstruct.line = port->minor; + serstruct.port = port->port_number; serstruct.flags = ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ; serstruct.xmit_fifo_size = kfifo_size(&port->write_fifo); serstruct.custom_divisor = 0; @@ -626,7 +619,7 @@ static int firm_open(struct usb_serial_port *port) { struct whiteheat_simple open_command; - open_command.port = port->number - port->serial->minor + 1; + open_command.port = port->port_number + 1; return firm_send_command(port, WHITEHEAT_OPEN, (__u8 *)&open_command, sizeof(open_command)); } @@ -636,7 +629,7 @@ static int firm_close(struct usb_serial_port *port) { struct whiteheat_simple close_command; - close_command.port = port->number - port->serial->minor + 1; + close_command.port = port->port_number + 1; return firm_send_command(port, WHITEHEAT_CLOSE, (__u8 *)&close_command, sizeof(close_command)); } @@ -649,7 +642,7 @@ static void firm_setup_port(struct tty_struct *tty) struct whiteheat_port_settings port_settings; unsigned int cflag = tty->termios.c_cflag; - port_settings.port = port->number + 1; + port_settings.port = port->port_number + 1; /* get the byte size */ switch (cflag & CSIZE) { @@ -726,7 +719,7 @@ static int firm_set_rts(struct usb_serial_port *port, __u8 onoff) { struct whiteheat_set_rdb rts_command; - rts_command.port = port->number - port->serial->minor + 1; + rts_command.port = port->port_number + 1; rts_command.state = onoff; return firm_send_command(port, WHITEHEAT_SET_RTS, (__u8 *)&rts_command, sizeof(rts_command)); @@ -737,7 +730,7 @@ static int firm_set_dtr(struct usb_serial_port *port, __u8 onoff) { struct whiteheat_set_rdb dtr_command; - dtr_command.port = port->number - port->serial->minor + 1; + dtr_command.port = port->port_number + 1; dtr_command.state = onoff; return firm_send_command(port, WHITEHEAT_SET_DTR, (__u8 *)&dtr_command, sizeof(dtr_command)); @@ -748,7 +741,7 @@ static int firm_set_break(struct usb_serial_port *port, __u8 onoff) { struct whiteheat_set_rdb break_command; - break_command.port = port->number - port->serial->minor + 1; + break_command.port = port->port_number + 1; break_command.state = onoff; return firm_send_command(port, WHITEHEAT_SET_BREAK, (__u8 *)&break_command, sizeof(break_command)); @@ -759,7 +752,7 @@ static int firm_purge(struct usb_serial_port *port, __u8 rxtx) { struct whiteheat_purge purge_command; - purge_command.port = port->number - port->serial->minor + 1; + purge_command.port = port->port_number + 1; purge_command.what = rxtx; return firm_send_command(port, WHITEHEAT_PURGE, (__u8 *)&purge_command, sizeof(purge_command)); @@ -770,7 +763,7 @@ static int firm_get_dtr_rts(struct usb_serial_port *port) { struct whiteheat_simple get_dr_command; - get_dr_command.port = port->number - port->serial->minor + 1; + get_dr_command.port = port->port_number + 1; return firm_send_command(port, WHITEHEAT_GET_DTR_RTS, (__u8 *)&get_dr_command, sizeof(get_dr_command)); } @@ -780,7 +773,7 @@ static int firm_report_tx_done(struct usb_serial_port *port) { struct whiteheat_simple close_command; - close_command.port = port->number - port->serial->minor + 1; + close_command.port = port->port_number + 1; return firm_send_command(port, WHITEHEAT_REPORT_TX_DONE, (__u8 *)&close_command, sizeof(close_command)); } diff --git a/drivers/usb/serial/wishbone-serial.c b/drivers/usb/serial/wishbone-serial.c new file mode 100644 index 00000000000..4fed4a0bd70 --- /dev/null +++ b/drivers/usb/serial/wishbone-serial.c @@ -0,0 +1,94 @@ +/* + * USB Wishbone-Serial adapter driver + * + * Copyright (C) 2013 Wesley W. Terpstra <w.terpstra@gsi.de> + * Copyright (C) 2013 GSI Helmholtz Centre for Heavy Ion Research GmbH + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + */ + +#include <linux/kernel.h> +#include <linux/tty.h> +#include <linux/module.h> +#include <linux/usb.h> +#include <linux/usb/serial.h> +#include <linux/uaccess.h> + +#define GSI_VENDOR_OPENCLOSE 0xB0 + +static const struct usb_device_id id_table[] = { + { USB_DEVICE_AND_INTERFACE_INFO(0x1D50, 0x6062, 0xFF, 0xFF, 0xFF) }, + { }, +}; +MODULE_DEVICE_TABLE(usb, id_table); + +/* + * Etherbone must be told that a new stream has begun before data arrives. + * This is necessary to restart the negotiation of Wishbone bus parameters. + * Similarly, when the stream ends, Etherbone must be told so that the cycle + * line can be driven low in the case that userspace failed to do so. + */ +static int usb_gsi_openclose(struct usb_serial_port *port, int value) +{ + struct usb_device *dev = port->serial->dev; + + return usb_control_msg( + dev, + usb_sndctrlpipe(dev, 0), /* Send to EP0OUT */ + GSI_VENDOR_OPENCLOSE, + USB_DIR_OUT|USB_TYPE_VENDOR|USB_RECIP_INTERFACE, + value, /* wValue = device is open(1) or closed(0) */ + port->serial->interface->cur_altsetting->desc.bInterfaceNumber, + NULL, 0, /* There is no data stage */ + 5000); /* Timeout till operation fails */ +} + +static int wishbone_serial_open(struct tty_struct *tty, + struct usb_serial_port *port) +{ + int retval; + + retval = usb_gsi_openclose(port, 1); + if (retval) { + dev_err(&port->serial->dev->dev, + "Could not mark device as open (%d)\n", + retval); + return retval; + } + + retval = usb_serial_generic_open(tty, port); + if (retval) + usb_gsi_openclose(port, 0); + + return retval; +} + +static void wishbone_serial_close(struct usb_serial_port *port) +{ + usb_serial_generic_close(port); + usb_gsi_openclose(port, 0); +} + +static struct usb_serial_driver wishbone_serial_device = { + .driver = { + .owner = THIS_MODULE, + .name = "wishbone_serial", + }, + .id_table = id_table, + .num_ports = 1, + .open = &wishbone_serial_open, + .close = &wishbone_serial_close, +}; + +static struct usb_serial_driver * const serial_drivers[] = { + &wishbone_serial_device, NULL +}; + +module_usb_serial_driver(serial_drivers, id_table); + +MODULE_AUTHOR("Wesley W. Terpstra <w.terpstra@gsi.de>"); +MODULE_DESCRIPTION("USB Wishbone-Serial adapter"); +MODULE_LICENSE("GPL"); diff --git a/drivers/usb/serial/xsens_mt.c b/drivers/usb/serial/xsens_mt.c new file mode 100644 index 00000000000..4841fb57400 --- /dev/null +++ b/drivers/usb/serial/xsens_mt.c @@ -0,0 +1,85 @@ +/* + * Xsens MT USB driver + * + * Copyright (C) 2013 Xsens <info@xsens.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License version + * 2 as published by the Free Software Foundation. + */ + +#include <linux/kernel.h> +#include <linux/tty.h> +#include <linux/module.h> +#include <linux/usb.h> +#include <linux/usb/serial.h> +#include <linux/uaccess.h> + +#define XSENS_VID 0x2639 + +#define MTi_10_IMU_PID 0x0001 +#define MTi_20_VRU_PID 0x0002 +#define MTi_30_AHRS_PID 0x0003 + +#define MTi_100_IMU_PID 0x0011 +#define MTi_200_VRU_PID 0x0012 +#define MTi_300_AHRS_PID 0x0013 + +#define MTi_G_700_GPS_INS_PID 0x0017 + +static const struct usb_device_id id_table[] = { + { USB_DEVICE(XSENS_VID, MTi_10_IMU_PID) }, + { USB_DEVICE(XSENS_VID, MTi_20_VRU_PID) }, + { USB_DEVICE(XSENS_VID, MTi_30_AHRS_PID) }, + + { USB_DEVICE(XSENS_VID, MTi_100_IMU_PID) }, + { USB_DEVICE(XSENS_VID, MTi_200_VRU_PID) }, + { USB_DEVICE(XSENS_VID, MTi_300_AHRS_PID) }, + + { USB_DEVICE(XSENS_VID, MTi_G_700_GPS_INS_PID) }, + { }, +}; +MODULE_DEVICE_TABLE(usb, id_table); + +static int has_required_endpoints(const struct usb_host_interface *interface) +{ + __u8 i; + int has_bulk_in = 0; + int has_bulk_out = 0; + + for (i = 0; i < interface->desc.bNumEndpoints; ++i) { + if (usb_endpoint_is_bulk_in(&interface->endpoint[i].desc)) + has_bulk_in = 1; + else if (usb_endpoint_is_bulk_out(&interface->endpoint[i].desc)) + has_bulk_out = 1; + } + + return has_bulk_in && has_bulk_out; +} + +static int xsens_mt_probe(struct usb_serial *serial, + const struct usb_device_id *id) +{ + if (!has_required_endpoints(serial->interface->cur_altsetting)) + return -ENODEV; + return 0; +} + +static struct usb_serial_driver xsens_mt_device = { + .driver = { + .owner = THIS_MODULE, + .name = "xsens_mt", + }, + .id_table = id_table, + .num_ports = 1, + + .probe = xsens_mt_probe, +}; + +static struct usb_serial_driver * const serial_drivers[] = { + &xsens_mt_device, NULL +}; + +module_usb_serial_driver(serial_drivers, id_table); + +MODULE_LICENSE("GPL"); diff --git a/drivers/usb/serial/zio.c b/drivers/usb/serial/zio.c deleted file mode 100644 index c043aa84a0b..00000000000 --- a/drivers/usb/serial/zio.c +++ /dev/null @@ -1,39 +0,0 @@ -/* - * ZIO Motherboard USB driver - * - * Copyright (C) 2010 Zilogic Systems <code@zilogic.com> - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License version - * 2 as published by the Free Software Foundation. - */ - -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/tty.h> -#include <linux/module.h> -#include <linux/usb.h> -#include <linux/usb/serial.h> -#include <linux/uaccess.h> - -static const struct usb_device_id id_table[] = { - { USB_DEVICE(0x1CBE, 0x0103) }, - { }, -}; -MODULE_DEVICE_TABLE(usb, id_table); - -static struct usb_serial_driver zio_device = { - .driver = { - .owner = THIS_MODULE, - .name = "zio", - }, - .id_table = id_table, - .num_ports = 1, -}; - -static struct usb_serial_driver * const serial_drivers[] = { - &zio_device, NULL -}; - -module_usb_serial_driver(serial_drivers, id_table); -MODULE_LICENSE("GPL"); diff --git a/drivers/usb/serial/zte_ev.c b/drivers/usb/serial/zte_ev.c index 39ee7373b4e..e40ab739c4a 100644 --- a/drivers/usb/serial/zte_ev.c +++ b/drivers/usb/serial/zte_ev.c @@ -13,7 +13,6 @@ * show the commands used to talk to the device, but I am not sure. */ #include <linux/kernel.h> -#include <linux/init.h> #include <linux/tty.h> #include <linux/slab.h> #include <linux/module.h> @@ -41,9 +40,6 @@ static int zte_ev_usb_serial_open(struct tty_struct *tty, int len; unsigned char *buf; - if (port->number != 0) - return -ENODEV; - buf = kmalloc(MAX_SETUP_DATA_SIZE, GFP_KERNEL); if (!buf) return -ENOMEM; @@ -53,10 +49,10 @@ static int zte_ev_usb_serial_open(struct tty_struct *tty, result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), 0x22, 0x21, 0x0001, 0x0000, NULL, len, - HZ * USB_CTRL_GET_TIMEOUT); + USB_CTRL_GET_TIMEOUT); dev_dbg(dev, "result = %d\n", result); - /* send 2st cmd and recieve data */ + /* send 2st cmd and receive data */ /* * 16.0 CTL a1 21 00 00 00 00 07 00 CLASS 25.1.0(5) * 16.0 DI 00 96 00 00 00 00 08 @@ -65,10 +61,10 @@ static int zte_ev_usb_serial_open(struct tty_struct *tty, result = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0), 0x21, 0xa1, 0x0000, 0x0000, buf, len, - HZ * USB_CTRL_GET_TIMEOUT); + USB_CTRL_GET_TIMEOUT); debug_data(dev, __func__, len, buf, result); - /* send 3 cmd */ + /* send 3rd cmd */ /* * 16.0 CTL 21 20 00 00 00 00 07 00 CLASS 30.1.0 * 16.0 DO 80 25 00 00 00 00 08 .%..... 30.2.0 @@ -84,10 +80,10 @@ static int zte_ev_usb_serial_open(struct tty_struct *tty, result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), 0x20, 0x21, 0x0000, 0x0000, buf, len, - HZ * USB_CTRL_GET_TIMEOUT); + USB_CTRL_GET_TIMEOUT); debug_data(dev, __func__, len, buf, result); - /* send 4 cmd */ + /* send 4th cmd */ /* * 16.0 CTL 21 22 03 00 00 00 00 00 */ @@ -95,10 +91,10 @@ static int zte_ev_usb_serial_open(struct tty_struct *tty, result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), 0x22, 0x21, 0x0003, 0x0000, NULL, len, - HZ * USB_CTRL_GET_TIMEOUT); + USB_CTRL_GET_TIMEOUT); dev_dbg(dev, "result = %d\n", result); - /* send 5 cmd */ + /* send 5th cmd */ /* * 16.0 CTL a1 21 00 00 00 00 07 00 CLASS 33.1.0 * 16.0 DI 80 25 00 00 00 00 08 @@ -107,10 +103,10 @@ static int zte_ev_usb_serial_open(struct tty_struct *tty, result = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0), 0x21, 0xa1, 0x0000, 0x0000, buf, len, - HZ * USB_CTRL_GET_TIMEOUT); + USB_CTRL_GET_TIMEOUT); debug_data(dev, __func__, len, buf, result); - /* send 6 cmd */ + /* send 6th cmd */ /* * 16.0 CTL 21 20 00 00 00 00 07 00 CLASS 34.1.0 * 16.0 DO 80 25 00 00 00 00 08 @@ -126,7 +122,7 @@ static int zte_ev_usb_serial_open(struct tty_struct *tty, result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), 0x20, 0x21, 0x0000, 0x0000, buf, len, - HZ * USB_CTRL_GET_TIMEOUT); + USB_CTRL_GET_TIMEOUT); debug_data(dev, __func__, len, buf, result); kfree(buf); @@ -166,9 +162,6 @@ static void zte_ev_usb_serial_close(struct usb_serial_port *port) int len; unsigned char *buf; - if (port->number != 0) - return; - buf = kmalloc(MAX_SETUP_DATA_SIZE, GFP_KERNEL); if (!buf) return; @@ -178,7 +171,7 @@ static void zte_ev_usb_serial_close(struct usb_serial_port *port) result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), 0x22, 0x21, 0x0002, 0x0000, NULL, len, - HZ * USB_CTRL_GET_TIMEOUT); + USB_CTRL_GET_TIMEOUT); dev_dbg(dev, "result = %d\n", result); /* send 2st ctl cmd(CTL 21 22 03 00 00 00 00 00 ) */ @@ -186,7 +179,7 @@ static void zte_ev_usb_serial_close(struct usb_serial_port *port) result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), 0x22, 0x21, 0x0003, 0x0000, NULL, len, - HZ * USB_CTRL_GET_TIMEOUT); + USB_CTRL_GET_TIMEOUT); dev_dbg(dev, "result = %d\n", result); /* send 3st cmd and recieve data */ @@ -198,10 +191,10 @@ static void zte_ev_usb_serial_close(struct usb_serial_port *port) result = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0), 0x21, 0xa1, 0x0000, 0x0000, buf, len, - HZ * USB_CTRL_GET_TIMEOUT); + USB_CTRL_GET_TIMEOUT); debug_data(dev, __func__, len, buf, result); - /* send 4 cmd */ + /* send 4th cmd */ /* * 16.0 CTL 21 20 00 00 00 00 07 00 CLASS 30.1.0 * 16.0 DO 00 c2 01 00 00 00 08 .%..... 30.2.0 @@ -217,10 +210,10 @@ static void zte_ev_usb_serial_close(struct usb_serial_port *port) result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), 0x20, 0x21, 0x0000, 0x0000, buf, len, - HZ * USB_CTRL_GET_TIMEOUT); + USB_CTRL_GET_TIMEOUT); debug_data(dev, __func__, len, buf, result); - /* send 5 cmd */ + /* send 5th cmd */ /* * 16.0 CTL 21 22 03 00 00 00 00 00 */ @@ -228,10 +221,10 @@ static void zte_ev_usb_serial_close(struct usb_serial_port *port) result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), 0x22, 0x21, 0x0003, 0x0000, NULL, len, - HZ * USB_CTRL_GET_TIMEOUT); + USB_CTRL_GET_TIMEOUT); dev_dbg(dev, "result = %d\n", result); - /* send 6 cmd */ + /* send 6th cmd */ /* * 16.0 CTL a1 21 00 00 00 00 07 00 CLASS 33.1.0 * 16.0 DI 00 c2 01 00 00 00 08 @@ -240,10 +233,10 @@ static void zte_ev_usb_serial_close(struct usb_serial_port *port) result = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0), 0x21, 0xa1, 0x0000, 0x0000, buf, len, - HZ * USB_CTRL_GET_TIMEOUT); + USB_CTRL_GET_TIMEOUT); debug_data(dev, __func__, len, buf, result); - /* send 7 cmd */ + /* send 7th cmd */ /* * 16.0 CTL 21 20 00 00 00 00 07 00 CLASS 354.1.0 * 16.0 DO 00 c2 01 00 00 00 08 ....... 354.2.0 @@ -259,10 +252,10 @@ static void zte_ev_usb_serial_close(struct usb_serial_port *port) result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), 0x20, 0x21, 0x0000, 0x0000, buf, len, - HZ * USB_CTRL_GET_TIMEOUT); + USB_CTRL_GET_TIMEOUT); debug_data(dev, __func__, len, buf, result); - /* send 8 cmd */ + /* send 8th cmd */ /* * 16.0 CTL 21 22 03 00 00 00 00 00 */ @@ -270,7 +263,7 @@ static void zte_ev_usb_serial_close(struct usb_serial_port *port) result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), 0x22, 0x21, 0x0003, 0x0000, NULL, len, - HZ * USB_CTRL_GET_TIMEOUT); + USB_CTRL_GET_TIMEOUT); dev_dbg(dev, "result = %d\n", result); kfree(buf); @@ -279,11 +272,28 @@ static void zte_ev_usb_serial_close(struct usb_serial_port *port) } static const struct usb_device_id id_table[] = { - { USB_DEVICE(0x19d2, 0xffff) }, /* AC8700 */ - { USB_DEVICE(0x19d2, 0xfffe) }, - { USB_DEVICE(0x19d2, 0xfffd) }, /* MG880 */ + /* AC8710, AC8710T */ + { USB_DEVICE_AND_INTERFACE_INFO(0x19d2, 0xffff, 0xff, 0xff, 0xff) }, + /* AC8700 */ + { USB_DEVICE_AND_INTERFACE_INFO(0x19d2, 0xfffe, 0xff, 0xff, 0xff) }, + /* MG880 */ + { USB_DEVICE(0x19d2, 0xfffd) }, + { USB_DEVICE(0x19d2, 0xfffc) }, + { USB_DEVICE(0x19d2, 0xfffb) }, + /* AC8710_V3 */ + { USB_DEVICE(0x19d2, 0xfff6) }, + { USB_DEVICE(0x19d2, 0xfff7) }, + { USB_DEVICE(0x19d2, 0xfff8) }, + { USB_DEVICE(0x19d2, 0xfff9) }, + { USB_DEVICE(0x19d2, 0xffee) }, + /* AC2716, MC2716 */ + { USB_DEVICE_AND_INTERFACE_INFO(0x19d2, 0xffed, 0xff, 0xff, 0xff) }, + /* AD3812 */ + { USB_DEVICE_AND_INTERFACE_INFO(0x19d2, 0xffeb, 0xff, 0xff, 0xff) }, + { USB_DEVICE(0x19d2, 0xffec) }, { USB_DEVICE(0x05C6, 0x3197) }, { USB_DEVICE(0x05C6, 0x6000) }, + { USB_DEVICE(0x05C6, 0x9008) }, { }, }; MODULE_DEVICE_TABLE(usb, id_table); |