1 files changed, 374 insertions, 292 deletions

diff --git a/drivers/usb/serial/pl2303.c b/drivers/usb/serial/pl2303.c
index 60024190136..b3d5a35c0d4 100644
--- a/drivers/usb/serial/pl2303.c
+++ b/drivers/usb/serial/pl2303.c
@@ -12,12 +12,10 @@
  *
  * See Documentation/usb/usb-serial.txt for more information on using this
  * driver
- *
  */
 
 #include <linux/kernel.h>
 #include <linux/errno.h>
-#include <linux/init.h>
 #include <linux/slab.h>
 #include <linux/tty.h>
 #include <linux/tty_driver.h>
@@ -29,12 +27,12 @@
 #include <linux/uaccess.h>
 #include <linux/usb.h>
 #include <linux/usb/serial.h>
+#include <asm/unaligned.h>
 #include "pl2303.h"
 
-/*
- * Version Information
- */
-#define DRIVER_DESC "Prolific PL2303 USB to serial adaptor driver"
+
+#define PL2303_QUIRK_UART_STATE_IDX0		BIT(0)
+#define PL2303_QUIRK_LEGACY			BIT(1)
 
 static const struct usb_device_id id_table[] = {
 	{ USB_DEVICE(PL2303_VENDOR_ID, PL2303_PRODUCT_ID) },
@@ -63,9 +61,12 @@ static const struct usb_device_id id_table[] = {
 	{ USB_DEVICE(SITECOM_VENDOR_ID, SITECOM_PRODUCT_ID) },
 	{ USB_DEVICE(ALCATEL_VENDOR_ID, ALCATEL_PRODUCT_ID) },
 	{ USB_DEVICE(SAMSUNG_VENDOR_ID, SAMSUNG_PRODUCT_ID) },
-	{ USB_DEVICE(SIEMENS_VENDOR_ID, SIEMENS_PRODUCT_ID_SX1) },
-	{ USB_DEVICE(SIEMENS_VENDOR_ID, SIEMENS_PRODUCT_ID_X65) },
-	{ USB_DEVICE(SIEMENS_VENDOR_ID, SIEMENS_PRODUCT_ID_X75) },
+	{ USB_DEVICE(SIEMENS_VENDOR_ID, SIEMENS_PRODUCT_ID_SX1),
+		.driver_info = PL2303_QUIRK_UART_STATE_IDX0 },
+	{ USB_DEVICE(SIEMENS_VENDOR_ID, SIEMENS_PRODUCT_ID_X65),
+		.driver_info = PL2303_QUIRK_UART_STATE_IDX0 },
+	{ USB_DEVICE(SIEMENS_VENDOR_ID, SIEMENS_PRODUCT_ID_X75),
+		.driver_info = PL2303_QUIRK_UART_STATE_IDX0 },
 	{ USB_DEVICE(SIEMENS_VENDOR_ID, SIEMENS_PRODUCT_ID_EF81) },
 	{ USB_DEVICE(BENQ_VENDOR_ID, BENQ_PRODUCT_ID_S81) }, /* Benq/Siemens S81 */
 	{ USB_DEVICE(SYNTECH_VENDOR_ID, SYNTECH_PRODUCT_ID) },
@@ -82,6 +83,9 @@ static const struct usb_device_id id_table[] = {
 	{ USB_DEVICE(YCCABLE_VENDOR_ID, YCCABLE_PRODUCT_ID) },
 	{ USB_DEVICE(SUPERIAL_VENDOR_ID, SUPERIAL_PRODUCT_ID) },
 	{ USB_DEVICE(HP_VENDOR_ID, HP_LD220_PRODUCT_ID) },
+	{ USB_DEVICE(HP_VENDOR_ID, HP_LD960_PRODUCT_ID) },
+	{ USB_DEVICE(HP_VENDOR_ID, HP_LCM220_PRODUCT_ID) },
+	{ USB_DEVICE(HP_VENDOR_ID, HP_LCM960_PRODUCT_ID) },
 	{ USB_DEVICE(CRESSI_VENDOR_ID, CRESSI_EDY_PRODUCT_ID) },
 	{ USB_DEVICE(ZEAGLE_VENDOR_ID, ZEAGLE_N2ITION3_PRODUCT_ID) },
 	{ USB_DEVICE(SONY_VENDOR_ID, SONY_QN3USB_PRODUCT_ID) },
@@ -115,7 +119,8 @@ MODULE_DEVICE_TABLE(usb, id_table);
 #define VENDOR_READ_REQUEST_TYPE	0xc0
 #define VENDOR_READ_REQUEST		0x01
 
-#define UART_STATE			0x08
+#define UART_STATE_INDEX		8
+#define UART_STATE_MSR_MASK		0x8b
 #define UART_STATE_TRANSIENT_MASK	0x74
 #define UART_DCD			0x01
 #define UART_DSR			0x02
@@ -128,99 +133,142 @@ MODULE_DEVICE_TABLE(usb, id_table);
 
 
 enum pl2303_type {
-	type_0,		/* don't know the difference between type 0 and */
-	type_1,		/* type 1, until someone from prolific tells us... */
-	HX,		/* HX version of the pl2303 chip */
+	TYPE_01,	/* Type 0 and 1 (difference unknown) */
+	TYPE_HX,	/* HX version of the pl2303 chip */
+	TYPE_COUNT
+};
+
+struct pl2303_type_data {
+	speed_t max_baud_rate;
+	unsigned long quirks;
 };
 
 struct pl2303_serial_private {
-	enum pl2303_type type;
+	const struct pl2303_type_data *type;
+	unsigned long quirks;
 };
 
 struct pl2303_private {
 	spinlock_t lock;
-	wait_queue_head_t delta_msr_wait;
 	u8 line_control;
 	u8 line_status;
+
+	u8 line_settings[7];
 };
 
-static int pl2303_vendor_read(__u16 value, __u16 index,
-		struct usb_serial *serial, unsigned char *buf)
+static const struct pl2303_type_data pl2303_type_data[TYPE_COUNT] = {
+	[TYPE_01] = {
+		.max_baud_rate =	1228800,
+		.quirks =		PL2303_QUIRK_LEGACY,
+	},
+};
+
+static int pl2303_vendor_read(struct usb_serial *serial, u16 value,
+							unsigned char buf[1])
 {
-	int res = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
+	struct device *dev = &serial->interface->dev;
+	int res;
+
+	res = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
 			VENDOR_READ_REQUEST, VENDOR_READ_REQUEST_TYPE,
-			value, index, buf, 1, 100);
-	dev_dbg(&serial->dev->dev, "0x%x:0x%x:0x%x:0x%x  %d - %x\n",
-		VENDOR_READ_REQUEST_TYPE, VENDOR_READ_REQUEST, value, index,
-		res, buf[0]);
-	return res;
+			value, 0, buf, 1, 100);
+	if (res != 1) {
+		dev_err(dev, "%s - failed to read [%04x]: %d\n", __func__,
+								value, res);
+		if (res >= 0)
+			res = -EIO;
+
+		return res;
+	}
+
+	dev_dbg(dev, "%s - [%04x] = %02x\n", __func__, value, buf[0]);
+
+	return 0;
 }
 
-static int pl2303_vendor_write(__u16 value, __u16 index,
-		struct usb_serial *serial)
+static int pl2303_vendor_write(struct usb_serial *serial, u16 value, u16 index)
 {
-	int res = usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0),
+	struct device *dev = &serial->interface->dev;
+	int res;
+
+	dev_dbg(dev, "%s - [%04x] = %02x\n", __func__, value, index);
+
+	res = usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0),
 			VENDOR_WRITE_REQUEST, VENDOR_WRITE_REQUEST_TYPE,
 			value, index, NULL, 0, 100);
-	dev_dbg(&serial->dev->dev, "0x%x:0x%x:0x%x:0x%x  %d\n",
-		VENDOR_WRITE_REQUEST_TYPE, VENDOR_WRITE_REQUEST, value, index,
-		res);
-	return res;
+	if (res) {
+		dev_err(dev, "%s - failed to write [%04x]: %d\n", __func__,
+								value, res);
+		return res;
+	}
+
+	return 0;
+}
+
+static int pl2303_probe(struct usb_serial *serial,
+					const struct usb_device_id *id)
+{
+	usb_set_serial_data(serial, (void *)id->driver_info);
+
+	return 0;
 }
 
 static int pl2303_startup(struct usb_serial *serial)
 {
 	struct pl2303_serial_private *spriv;
-	enum pl2303_type type = type_0;
+	enum pl2303_type type = TYPE_01;
 	unsigned char *buf;
 
 	spriv = kzalloc(sizeof(*spriv), GFP_KERNEL);
 	if (!spriv)
 		return -ENOMEM;
 
-	buf = kmalloc(10, GFP_KERNEL);
+	buf = kmalloc(1, GFP_KERNEL);
 	if (!buf) {
 		kfree(spriv);
 		return -ENOMEM;
 	}
 
 	if (serial->dev->descriptor.bDeviceClass == 0x02)
-		type = type_0;
+		type = TYPE_01;		/* type 0 */
 	else if (serial->dev->descriptor.bMaxPacketSize0 == 0x40)
-		type = HX;
+		type = TYPE_HX;
 	else if (serial->dev->descriptor.bDeviceClass == 0x00)
-		type = type_1;
+		type = TYPE_01;		/* type 1 */
 	else if (serial->dev->descriptor.bDeviceClass == 0xFF)
-		type = type_1;
+		type = TYPE_01;		/* type 1 */
 	dev_dbg(&serial->interface->dev, "device type: %d\n", type);
 
-	spriv->type = type;
+	spriv->type = &pl2303_type_data[type];
+	spriv->quirks = (unsigned long)usb_get_serial_data(serial);
+	spriv->quirks |= spriv->type->quirks;
+
 	usb_set_serial_data(serial, spriv);
 
-	pl2303_vendor_read(0x8484, 0, serial, buf);
-	pl2303_vendor_write(0x0404, 0, serial);
-	pl2303_vendor_read(0x8484, 0, serial, buf);
-	pl2303_vendor_read(0x8383, 0, serial, buf);
-	pl2303_vendor_read(0x8484, 0, serial, buf);
-	pl2303_vendor_write(0x0404, 1, serial);
-	pl2303_vendor_read(0x8484, 0, serial, buf);
-	pl2303_vendor_read(0x8383, 0, serial, buf);
-	pl2303_vendor_write(0, 1, serial);
-	pl2303_vendor_write(1, 0, serial);
-	if (type == HX)
-		pl2303_vendor_write(2, 0x44, serial);
+	pl2303_vendor_read(serial, 0x8484, buf);
+	pl2303_vendor_write(serial, 0x0404, 0);
+	pl2303_vendor_read(serial, 0x8484, buf);
+	pl2303_vendor_read(serial, 0x8383, buf);
+	pl2303_vendor_read(serial, 0x8484, buf);
+	pl2303_vendor_write(serial, 0x0404, 1);
+	pl2303_vendor_read(serial, 0x8484, buf);
+	pl2303_vendor_read(serial, 0x8383, buf);
+	pl2303_vendor_write(serial, 0, 1);
+	pl2303_vendor_write(serial, 1, 0);
+	if (spriv->quirks & PL2303_QUIRK_LEGACY)
+		pl2303_vendor_write(serial, 2, 0x24);
 	else
-		pl2303_vendor_write(2, 0x24, serial);
+		pl2303_vendor_write(serial, 2, 0x44);
 
 	kfree(buf);
+
 	return 0;
 }
 
 static void pl2303_release(struct usb_serial *serial)
 {
-	struct pl2303_serial_private *spriv;
+	struct pl2303_serial_private *spriv = usb_get_serial_data(serial);
 
-	spriv = usb_get_serial_data(serial);
 	kfree(spriv);
 }
 
@@ -233,35 +281,181 @@ static int pl2303_port_probe(struct usb_serial_port *port)
 		return -ENOMEM;
 
 	spin_lock_init(&priv->lock);
-	init_waitqueue_head(&priv->delta_msr_wait);
 
 	usb_set_serial_port_data(port, priv);
 
+	port->port.drain_delay = 256;
+
 	return 0;
 }
 
 static int pl2303_port_remove(struct usb_serial_port *port)
 {
-	struct pl2303_private *priv;
+	struct pl2303_private *priv = usb_get_serial_port_data(port);
 
-	priv = usb_get_serial_port_data(port);
 	kfree(priv);
 
 	return 0;
 }
 
-static int set_control_lines(struct usb_device *dev, u8 value)
+static int pl2303_set_control_lines(struct usb_serial_port *port, u8 value)
 {
+	struct usb_device *dev = port->serial->dev;
 	int retval;
 
+	dev_dbg(&port->dev, "%s - %02x\n", __func__, value);
+
 	retval = usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
 				 SET_CONTROL_REQUEST, SET_CONTROL_REQUEST_TYPE,
 				 value, 0, NULL, 0, 100);
-	dev_dbg(&dev->dev, "%s - value = %d, retval = %d\n", __func__,
-		value, retval);
+	if (retval)
+		dev_err(&port->dev, "%s - failed: %d\n", __func__, retval);
+
 	return retval;
 }
 
+/*
+ * Returns the nearest supported baud rate that can be set directly without
+ * using divisors.
+ */
+static speed_t pl2303_get_supported_baud_rate(speed_t baud)
+{
+	static const speed_t baud_sup[] = {
+		75, 150, 300, 600, 1200, 1800, 2400, 3600, 4800, 7200, 9600,
+		14400, 19200, 28800, 38400, 57600, 115200, 230400, 460800,
+		614400, 921600, 1228800, 2457600, 3000000, 6000000
+	};
+
+	unsigned i;
+
+	for (i = 0; i < ARRAY_SIZE(baud_sup); ++i) {
+		if (baud_sup[i] > baud)
+			break;
+	}
+
+	if (i == ARRAY_SIZE(baud_sup))
+		baud = baud_sup[i - 1];
+	else if (i > 0 && (baud_sup[i] - baud) > (baud - baud_sup[i - 1]))
+		baud = baud_sup[i - 1];
+	else
+		baud = baud_sup[i];
+
+	return baud;
+}
+
+/*
+ * NOTE: If unsupported baud rates are set directly, the PL2303 seems to
+ *       use 9600 baud.
+ */
+static speed_t pl2303_encode_baud_rate_direct(unsigned char buf[4],
+								speed_t baud)
+{
+	put_unaligned_le32(baud, buf);
+
+	return baud;
+}
+
+static speed_t pl2303_encode_baud_rate_divisor(unsigned char buf[4],
+								speed_t baud)
+{
+	unsigned int tmp;
+
+	/*
+	 * Apparently the formula is:
+	 * baudrate = 12M * 32 / (2^buf[1]) / buf[0]
+	 */
+	tmp = 12000000 * 32 / baud;
+	buf[3] = 0x80;
+	buf[2] = 0;
+	buf[1] = (tmp >= 256);
+	while (tmp >= 256) {
+		tmp >>= 2;
+		buf[1] <<= 1;
+	}
+	buf[0] = tmp;
+
+	return baud;
+}
+
+static void pl2303_encode_baud_rate(struct tty_struct *tty,
+					struct usb_serial_port *port,
+					u8 buf[4])
+{
+	struct usb_serial *serial = port->serial;
+	struct pl2303_serial_private *spriv = usb_get_serial_data(serial);
+	speed_t	baud_sup;
+	speed_t baud;
+
+	baud = tty_get_baud_rate(tty);
+	dev_dbg(&port->dev, "baud requested = %u\n", baud);
+	if (!baud)
+		return;
+
+	if (spriv->type->max_baud_rate)
+		baud = min_t(speed_t, baud, spriv->type->max_baud_rate);
+	/*
+	 * Set baud rate to nearest supported value.
+	 *
+	 * NOTE: Baud rate 500k can only be set using divisors.
+	 */
+	baud_sup = pl2303_get_supported_baud_rate(baud);
+
+	if (baud == 500000)
+		baud = pl2303_encode_baud_rate_divisor(buf, baud);
+	else
+		baud = pl2303_encode_baud_rate_direct(buf, baud_sup);
+
+	/* Save resulting baud rate */
+	tty_encode_baud_rate(tty, baud, baud);
+	dev_dbg(&port->dev, "baud set = %u\n", baud);
+}
+
+static int pl2303_get_line_request(struct usb_serial_port *port,
+							unsigned char buf[7])
+{
+	struct usb_device *udev = port->serial->dev;
+	int ret;
+
+	ret = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0),
+				GET_LINE_REQUEST, GET_LINE_REQUEST_TYPE,
+				0, 0, buf, 7, 100);
+	if (ret != 7) {
+		dev_err(&port->dev, "%s - failed: %d\n", __func__, ret);
+
+		if (ret > 0)
+			ret = -EIO;
+
+		return ret;
+	}
+
+	dev_dbg(&port->dev, "%s - %7ph\n", __func__, buf);
+
+	return 0;
+}
+
+static int pl2303_set_line_request(struct usb_serial_port *port,
+							unsigned char buf[7])
+{
+	struct usb_device *udev = port->serial->dev;
+	int ret;
+
+	ret = usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
+				SET_LINE_REQUEST, SET_LINE_REQUEST_TYPE,
+				0, 0, buf, 7, 100);
+	if (ret != 7) {
+		dev_err(&port->dev, "%s - failed: %d\n", __func__, ret);
+
+		if (ret > 0)
+			ret = -EIO;
+
+		return ret;
+	}
+
+	dev_dbg(&port->dev, "%s - %7ph\n", __func__, buf);
+
+	return 0;
+}
+
 static void pl2303_set_termios(struct tty_struct *tty,
 		struct usb_serial_port *port, struct ktermios *old_termios)
 {
@@ -269,122 +463,51 @@ static void pl2303_set_termios(struct tty_struct *tty,
 	struct pl2303_serial_private *spriv = usb_get_serial_data(serial);
 	struct pl2303_private *priv = usb_get_serial_port_data(port);
 	unsigned long flags;
-	unsigned int cflag;
 	unsigned char *buf;
-	int baud;
-	int i;
+	int ret;
 	u8 control;
-	const int baud_sup[] = { 75, 150, 300, 600, 1200, 1800, 2400, 3600,
-	                         4800, 7200, 9600, 14400, 19200, 28800, 38400,
-	                         57600, 115200, 230400, 460800, 614400,
-	                         921600, 1228800, 2457600, 3000000, 6000000 };
-	int baud_floor, baud_ceil;
-	int k;
-
-	/* The PL2303 is reported to lose bytes if you change
-	   serial settings even to the same values as before. Thus
-	   we actually need to filter in this specific case */
-
-	if (!tty_termios_hw_change(&tty->termios, old_termios))
-		return;
 
-	cflag = tty->termios.c_cflag;
+	if (old_termios && !tty_termios_hw_change(&tty->termios, old_termios))
+		return;
 
 	buf = kzalloc(7, GFP_KERNEL);
 	if (!buf) {
-		dev_err(&port->dev, "%s - out of memory.\n", __func__);
 		/* Report back no change occurred */
-		tty->termios = *old_termios;
+		if (old_termios)
+			tty->termios = *old_termios;
 		return;
 	}
 
-	i = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
-			    GET_LINE_REQUEST, GET_LINE_REQUEST_TYPE,
-			    0, 0, buf, 7, 100);
-	dev_dbg(&port->dev, "0xa1:0x21:0:0  %d - %x %x %x %x %x %x %x\n", i,
-	    buf[0], buf[1], buf[2], buf[3], buf[4], buf[5], buf[6]);
+	pl2303_get_line_request(port, buf);
 
-	if (cflag & CSIZE) {
-		switch (cflag & CSIZE) {
-		case CS5:
-			buf[6] = 5;
-			break;
-		case CS6:
-			buf[6] = 6;
-			break;
-		case CS7:
-			buf[6] = 7;
-			break;
-		default:
-		case CS8:
-			buf[6] = 8;
-			break;
-		}
-		dev_dbg(&port->dev, "data bits = %d\n", buf[6]);
+	switch (C_CSIZE(tty)) {
+	case CS5:
+		buf[6] = 5;
+		break;
+	case CS6:
+		buf[6] = 6;
+		break;
+	case CS7:
+		buf[6] = 7;
+		break;
+	default:
+	case CS8:
+		buf[6] = 8;
 	}
+	dev_dbg(&port->dev, "data bits = %d\n", buf[6]);
 
 	/* For reference buf[0]:buf[3] baud rate value */
-	/* NOTE: Only the values defined in baud_sup are supported !
-	 *       => if unsupported values are set, the PL2303 seems to use
-	 *          9600 baud (at least my PL2303X always does)
-	 */
-	baud = tty_get_baud_rate(tty);
-	dev_dbg(&port->dev, "baud requested = %d\n", baud);
-	if (baud) {
-		/* Set baudrate to nearest supported value */
-		for (k=0; k<ARRAY_SIZE(baud_sup); k++) {
-			if (baud_sup[k] / baud) {
-				baud_ceil = baud_sup[k];
-				if (k==0) {
-					baud = baud_ceil;
-				} else {
-					baud_floor = baud_sup[k-1];
-					if ((baud_ceil % baud)
-					    > (baud % baud_floor))
-						baud = baud_floor;
-					else
-						baud = baud_ceil;
-				}
-				break;
-			}
-		}
-		if (baud > 1228800) {
-			/* type_0, type_1 only support up to 1228800 baud */
-			if (spriv->type != HX)
-				baud = 1228800;
-			else if (baud > 6000000)
-				baud = 6000000;
-		}
-		dev_dbg(&port->dev, "baud set = %d\n", baud);
-		if (baud <= 115200) {
-			buf[0] = baud & 0xff;
-			buf[1] = (baud >> 8) & 0xff;
-			buf[2] = (baud >> 16) & 0xff;
-			buf[3] = (baud >> 24) & 0xff;
-		} else {
-			/* apparently the formula for higher speeds is:
-			 * baudrate = 12M * 32 / (2^buf[1]) / buf[0]
-			 */
-			unsigned tmp = 12*1000*1000*32 / baud;
-			buf[3] = 0x80;
-			buf[2] = 0;
-			buf[1] = (tmp >= 256);
-			while (tmp >= 256) {
-				tmp >>= 2;
-				buf[1] <<= 1;
-			}
-			buf[0] = tmp;
-		}
-	}
+	pl2303_encode_baud_rate(tty, port, &buf[0]);
 
 	/* For reference buf[4]=0 is 1 stop bits */
 	/* For reference buf[4]=1 is 1.5 stop bits */
 	/* For reference buf[4]=2 is 2 stop bits */
-	if (cflag & CSTOPB) {
-		/* NOTE: Comply with "real" UARTs / RS232:
+	if (C_CSTOPB(tty)) {
+		/*
+		 * NOTE: Comply with "real" UARTs / RS232:
 		 *       use 1.5 instead of 2 stop bits with 5 data bits
 		 */
-		if ((cflag & CSIZE) == CS5) {
+		if (C_CSIZE(tty) == CS5) {
 			buf[4] = 1;
 			dev_dbg(&port->dev, "stop bits = 1.5\n");
 		} else {
@@ -396,14 +519,14 @@ static void pl2303_set_termios(struct tty_struct *tty,
 		dev_dbg(&port->dev, "stop bits = 1\n");
 	}
 
-	if (cflag & PARENB) {
+	if (C_PARENB(tty)) {
 		/* For reference buf[5]=0 is none parity */
 		/* For reference buf[5]=1 is odd parity */
 		/* For reference buf[5]=2 is even parity */
 		/* For reference buf[5]=3 is mark parity */
 		/* For reference buf[5]=4 is space parity */
-		if (cflag & PARODD) {
-			if (cflag & CMSPAR) {
+		if (C_PARODD(tty)) {
+			if (C_CMSPAR(tty)) {
 				buf[5] = 3;
 				dev_dbg(&port->dev, "parity = mark\n");
 			} else {
@@ -411,7 +534,7 @@ static void pl2303_set_termios(struct tty_struct *tty,
 				dev_dbg(&port->dev, "parity = odd\n");
 			}
 		} else {
-			if (cflag & CMSPAR) {
+			if (C_CMSPAR(tty)) {
 				buf[5] = 4;
 				dev_dbg(&port->dev, "parity = space\n");
 			} else {
@@ -424,47 +547,48 @@ static void pl2303_set_termios(struct tty_struct *tty,
 		dev_dbg(&port->dev, "parity = none\n");
 	}
 
-	i = usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0),
-			    SET_LINE_REQUEST, SET_LINE_REQUEST_TYPE,
-			    0, 0, buf, 7, 100);
-	dev_dbg(&port->dev, "0x21:0x20:0:0  %d\n", i);
+	/*
+	 * Some PL2303 are known to lose bytes if you change serial settings
+	 * even to the same values as before. Thus we actually need to filter
+	 * in this specific case.
+	 *
+	 * Note that the tty_termios_hw_change check above is not sufficient
+	 * as a previously requested baud rate may differ from the one
+	 * actually used (and stored in old_termios).
+	 *
+	 * NOTE: No additional locking needed for line_settings as it is
+	 *       only used in set_termios, which is serialised against itself.
+	 */
+	if (!old_termios || memcmp(buf, priv->line_settings, 7)) {
+		ret = pl2303_set_line_request(port, buf);
+		if (!ret)
+			memcpy(priv->line_settings, buf, 7);
+	}
 
 	/* change control lines if we are switching to or from B0 */
 	spin_lock_irqsave(&priv->lock, flags);
 	control = priv->line_control;
-	if ((cflag & CBAUD) == B0)
+	if (C_BAUD(tty) == B0)
 		priv->line_control &= ~(CONTROL_DTR | CONTROL_RTS);
-	else if ((old_termios->c_cflag & CBAUD) == B0)
+	else if (old_termios && (old_termios->c_cflag & CBAUD) == B0)
 		priv->line_control |= (CONTROL_DTR | CONTROL_RTS);
 	if (control != priv->line_control) {
 		control = priv->line_control;
 		spin_unlock_irqrestore(&priv->lock, flags);
-		set_control_lines(serial->dev, control);
+		pl2303_set_control_lines(port, control);
 	} else {
 		spin_unlock_irqrestore(&priv->lock, flags);
 	}
 
-	buf[0] = buf[1] = buf[2] = buf[3] = buf[4] = buf[5] = buf[6] = 0;
-
-	i = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
-			    GET_LINE_REQUEST, GET_LINE_REQUEST_TYPE,
-			    0, 0, buf, 7, 100);
-	dev_dbg(&port->dev, "0xa1:0x21:0:0  %d - %x %x %x %x %x %x %x\n", i,
-	     buf[0], buf[1], buf[2], buf[3], buf[4], buf[5], buf[6]);
-
-	if (cflag & CRTSCTS) {
-		if (spriv->type == HX)
-			pl2303_vendor_write(0x0, 0x61, serial);
+	if (C_CRTSCTS(tty)) {
+		if (spriv->quirks & PL2303_QUIRK_LEGACY)
+			pl2303_vendor_write(serial, 0x0, 0x41);
 		else
-			pl2303_vendor_write(0x0, 0x41, serial);
+			pl2303_vendor_write(serial, 0x0, 0x61);
 	} else {
-		pl2303_vendor_write(0x0, 0x0, serial);
+		pl2303_vendor_write(serial, 0x0, 0x0);
 	}
 
-	/* Save resulting baud rate */
-	if (baud)
-		tty_encode_baud_rate(tty, baud, baud);
-
 	kfree(buf);
 }
 
@@ -475,14 +599,14 @@ static void pl2303_dtr_rts(struct usb_serial_port *port, int on)
 	u8 control;
 
 	spin_lock_irqsave(&priv->lock, flags);
-	/* Change DTR and RTS */
 	if (on)
 		priv->line_control |= (CONTROL_DTR | CONTROL_RTS);
 	else
 		priv->line_control &= ~(CONTROL_DTR | CONTROL_RTS);
 	control = priv->line_control;
 	spin_unlock_irqrestore(&priv->lock, flags);
-	set_control_lines(port->serial->dev, control);
+
+	pl2303_set_control_lines(port, control);
 }
 
 static void pl2303_close(struct usb_serial_port *port)
@@ -493,28 +617,27 @@ static void pl2303_close(struct usb_serial_port *port)
 
 static int pl2303_open(struct tty_struct *tty, struct usb_serial_port *port)
 {
-	struct ktermios tmp_termios;
 	struct usb_serial *serial = port->serial;
 	struct pl2303_serial_private *spriv = usb_get_serial_data(serial);
 	int result;
 
-	if (spriv->type != HX) {
+	if (spriv->quirks & PL2303_QUIRK_LEGACY) {
 		usb_clear_halt(serial->dev, port->write_urb->pipe);
 		usb_clear_halt(serial->dev, port->read_urb->pipe);
 	} else {
 		/* reset upstream data pipes */
-		pl2303_vendor_write(8, 0, serial);
-		pl2303_vendor_write(9, 0, serial);
+		pl2303_vendor_write(serial, 8, 0);
+		pl2303_vendor_write(serial, 9, 0);
 	}
 
 	/* Setup termios */
 	if (tty)
-		pl2303_set_termios(tty, port, &tmp_termios);
+		pl2303_set_termios(tty, port, NULL);
 
 	result = usb_submit_urb(port->interrupt_in_urb, GFP_KERNEL);
 	if (result) {
-		dev_err(&port->dev, "%s - failed submitting interrupt urb,"
-			" error %d\n", __func__, result);
+		dev_err(&port->dev, "failed to submit interrupt urb: %d\n",
+			result);
 		return result;
 	}
 
@@ -524,7 +647,6 @@ static int pl2303_open(struct tty_struct *tty, struct usb_serial_port *port)
 		return result;
 	}
 
-	port->port.drain_delay = 256;
 	return 0;
 }
 
@@ -532,7 +654,6 @@ static int pl2303_tiocmset(struct tty_struct *tty,
 			   unsigned int set, unsigned int clear)
 {
 	struct usb_serial_port *port = tty->driver_data;
-	struct usb_serial *serial = port->serial;
 	struct pl2303_private *priv = usb_get_serial_port_data(port);
 	unsigned long flags;
 	u8 control;
@@ -550,14 +671,11 @@ static int pl2303_tiocmset(struct tty_struct *tty,
 	control = priv->line_control;
 	spin_unlock_irqrestore(&priv->lock, flags);
 
-	mutex_lock(&serial->disc_mutex);
-	if (!serial->disconnected)
-		ret = set_control_lines(serial->dev, control);
-	else
-		ret = -ENODEV;
-	mutex_unlock(&serial->disc_mutex);
+	ret = pl2303_set_control_lines(port, control);
+	if (ret)
+		return usb_translate_errors(ret);
 
-	return ret;
+	return 0;
 }
 
 static int pl2303_tiocmget(struct tty_struct *tty)
@@ -589,44 +707,10 @@ static int pl2303_tiocmget(struct tty_struct *tty)
 static int pl2303_carrier_raised(struct usb_serial_port *port)
 {
 	struct pl2303_private *priv = usb_get_serial_port_data(port);
+
 	if (priv->line_status & UART_DCD)
 		return 1;
-	return 0;
-}
-
-static int wait_modem_info(struct usb_serial_port *port, unsigned int arg)
-{
-	struct pl2303_private *priv = usb_get_serial_port_data(port);
-	unsigned long flags;
-	unsigned int prevstatus;
-	unsigned int status;
-	unsigned int changed;
-
-	spin_lock_irqsave(&priv->lock, flags);
-	prevstatus = priv->line_status;
-	spin_unlock_irqrestore(&priv->lock, flags);
-
-	while (1) {
-		interruptible_sleep_on(&priv->delta_msr_wait);
-		/* see if a signal did it */
-		if (signal_pending(current))
-			return -ERESTARTSYS;
-
-		spin_lock_irqsave(&priv->lock, flags);
-		status = priv->line_status;
-		spin_unlock_irqrestore(&priv->lock, flags);
-
-		changed = prevstatus ^ status;
 
-		if (((arg & TIOCM_RNG) && (changed & UART_RING)) ||
-		    ((arg & TIOCM_DSR) && (changed & UART_DSR)) ||
-		    ((arg & TIOCM_CD)  && (changed & UART_DCD)) ||
-		    ((arg & TIOCM_CTS) && (changed & UART_CTS))) {
-			return 0;
-		}
-		prevstatus = status;
-	}
-	/* NOTREACHED */
 	return 0;
 }
 
@@ -636,28 +720,22 @@ static int pl2303_ioctl(struct tty_struct *tty,
 	struct serial_struct ser;
 	struct usb_serial_port *port = tty->driver_data;
 
-	dev_dbg(&port->dev, "%s cmd = 0x%04x\n", __func__, cmd);
-
 	switch (cmd) {
 	case TIOCGSERIAL:
 		memset(&ser, 0, sizeof ser);
 		ser.type = PORT_16654;
-		ser.line = port->serial->minor;
-		ser.port = port->number;
+		ser.line = port->minor;
+		ser.port = port->port_number;
 		ser.baud_base = 460800;
 
 		if (copy_to_user((void __user *)arg, &ser, sizeof ser))
 			return -EFAULT;
 
 		return 0;
-
-	case TIOCMIWAIT:
-		dev_dbg(&port->dev, "%s TIOCMIWAIT\n", __func__);
-		return wait_modem_info(port, arg);
 	default:
-		dev_dbg(&port->dev, "%s not supported = 0x%04x\n", __func__, cmd);
 		break;
 	}
+
 	return -ENOIOCTLCMD;
 }
 
@@ -672,6 +750,7 @@ static void pl2303_break_ctl(struct tty_struct *tty, int break_state)
 		state = BREAK_OFF;
 	else
 		state = BREAK_ON;
+
 	dev_dbg(&port->dev, "%s - turning break %s\n", __func__,
 			state == BREAK_OFF ? "off" : "on");
 
@@ -686,48 +765,51 @@ static void pl2303_update_line_status(struct usb_serial_port *port,
 				      unsigned char *data,
 				      unsigned int actual_length)
 {
-
+	struct usb_serial *serial = port->serial;
+	struct pl2303_serial_private *spriv = usb_get_serial_data(serial);
 	struct pl2303_private *priv = usb_get_serial_port_data(port);
 	struct tty_struct *tty;
 	unsigned long flags;
-	u8 status_idx = UART_STATE;
-	u8 length = UART_STATE + 1;
-	u8 prev_line_status;
-	u16 idv, idp;
+	unsigned int status_idx = UART_STATE_INDEX;
+	u8 status;
+	u8 delta;
 
-	idv = le16_to_cpu(port->serial->dev->descriptor.idVendor);
-	idp = le16_to_cpu(port->serial->dev->descriptor.idProduct);
+	if (spriv->quirks & PL2303_QUIRK_UART_STATE_IDX0)
+		status_idx = 0;
 
-
-	if (idv == SIEMENS_VENDOR_ID) {
-		if (idp == SIEMENS_PRODUCT_ID_X65 ||
-		    idp == SIEMENS_PRODUCT_ID_SX1 ||
-		    idp == SIEMENS_PRODUCT_ID_X75) {
-
-			length = 1;
-			status_idx = 0;
-		}
-	}
-
-	if (actual_length < length)
+	if (actual_length < status_idx + 1)
 		return;
 
+	status = data[status_idx];
+
 	/* Save off the uart status for others to look at */
 	spin_lock_irqsave(&priv->lock, flags);
-	prev_line_status = priv->line_status;
-	priv->line_status = data[status_idx];
+	delta = priv->line_status ^ status;
+	priv->line_status = status;
 	spin_unlock_irqrestore(&priv->lock, flags);
-	if (priv->line_status & UART_BREAK_ERROR)
+
+	if (status & UART_BREAK_ERROR)
 		usb_serial_handle_break(port);
-	wake_up_interruptible(&priv->delta_msr_wait);
 
-	tty = tty_port_tty_get(&port->port);
-	if (!tty)
-		return;
-	if ((priv->line_status ^ prev_line_status) & UART_DCD)
-		usb_serial_handle_dcd_change(port, tty,
-				priv->line_status & UART_DCD);
-	tty_kref_put(tty);
+	if (delta & UART_STATE_MSR_MASK) {
+		if (delta & UART_CTS)
+			port->icount.cts++;
+		if (delta & UART_DSR)
+			port->icount.dsr++;
+		if (delta & UART_RING)
+			port->icount.rng++;
+		if (delta & UART_DCD) {
+			port->icount.dcd++;
+			tty = tty_port_tty_get(&port->port);
+			if (tty) {
+				usb_serial_handle_dcd_change(port, tty,
+							status & UART_DCD);
+				tty_kref_put(tty);
+			}
+		}
+
+		wake_up_interruptible(&port->port.delta_msr_wait);
+	}
 }
 
 static void pl2303_read_int_callback(struct urb *urb)
@@ -762,17 +844,17 @@ static void pl2303_read_int_callback(struct urb *urb)
 
 exit:
 	retval = usb_submit_urb(urb, GFP_ATOMIC);
-	if (retval)
+	if (retval) {
 		dev_err(&port->dev,
 			"%s - usb_submit_urb failed with result %d\n",
 			__func__, retval);
+	}
 }
 
 static void pl2303_process_read_urb(struct urb *urb)
 {
 	struct usb_serial_port *port = urb->context;
 	struct pl2303_private *priv = usb_get_serial_port_data(port);
-	struct tty_struct *tty;
 	unsigned char *data = urb->transfer_buffer;
 	char tty_flag = TTY_NORMAL;
 	unsigned long flags;
@@ -784,43 +866,41 @@ static void pl2303_process_read_urb(struct urb *urb)
 	line_status = priv->line_status;
 	priv->line_status &= ~UART_STATE_TRANSIENT_MASK;
 	spin_unlock_irqrestore(&priv->lock, flags);
-	wake_up_interruptible(&priv->delta_msr_wait);
 
 	if (!urb->actual_length)
 		return;
 
-	tty = tty_port_tty_get(&port->port);
-	if (!tty)
-		return;
-
-	/* break takes precedence over parity, */
-	/* which takes precedence over framing errors */
+	/*
+	 * Break takes precedence over parity, which takes precedence over
+	 * framing errors.
+	 */
 	if (line_status & UART_BREAK_ERROR)
 		tty_flag = TTY_BREAK;
 	else if (line_status & UART_PARITY_ERROR)
 		tty_flag = TTY_PARITY;
 	else if (line_status & UART_FRAME_ERROR)
 		tty_flag = TTY_FRAME;
-	dev_dbg(&port->dev, "%s - tty_flag = %d\n", __func__, tty_flag);
 
+	if (tty_flag != TTY_NORMAL)
+		dev_dbg(&port->dev, "%s - tty_flag = %d\n", __func__,
+								tty_flag);
 	/* overrun is special, not associated with a char */
 	if (line_status & UART_OVERRUN_ERROR)
-		tty_insert_flip_char(tty, 0, TTY_OVERRUN);
+		tty_insert_flip_char(&port->port, 0, TTY_OVERRUN);
 
 	if (port->port.console && port->sysrq) {
 		for (i = 0; i < urb->actual_length; ++i)
 			if (!usb_serial_handle_sysrq_char(port, data[i]))
-				tty_insert_flip_char(tty, data[i], tty_flag);
+				tty_insert_flip_char(&port->port, data[i],
+						tty_flag);
 	} else {
-		tty_insert_flip_string_fixed_flag(tty, data, tty_flag,
+		tty_insert_flip_string_fixed_flag(&port->port, data, tty_flag,
 							urb->actual_length);
 	}
 
-	tty_flip_buffer_push(tty);
-	tty_kref_put(tty);
+	tty_flip_buffer_push(&port->port);
 }
 
-/* All of the device info needed for the PL2303 SIO serial converter */
 static struct usb_serial_driver pl2303_device = {
 	.driver = {
 		.owner =	THIS_MODULE,
@@ -832,15 +912,17 @@ static struct usb_serial_driver pl2303_device = {
 	.bulk_out_size =	256,
 	.open =			pl2303_open,
 	.close =		pl2303_close,
-	.dtr_rts = 		pl2303_dtr_rts,
+	.dtr_rts =		pl2303_dtr_rts,
 	.carrier_raised =	pl2303_carrier_raised,
 	.ioctl =		pl2303_ioctl,
 	.break_ctl =		pl2303_break_ctl,
 	.set_termios =		pl2303_set_termios,
 	.tiocmget =		pl2303_tiocmget,
 	.tiocmset =		pl2303_tiocmset,
+	.tiocmiwait =		usb_serial_generic_tiocmiwait,
 	.process_read_urb =	pl2303_process_read_urb,
 	.read_int_callback =	pl2303_read_int_callback,
+	.probe =		pl2303_probe,
 	.attach =		pl2303_startup,
 	.release =		pl2303_release,
 	.port_probe =		pl2303_port_probe,
@@ -853,5 +935,5 @@ static struct usb_serial_driver * const serial_drivers[] = {
 
 module_usb_serial_driver(serial_drivers, id_table);
 
-MODULE_DESCRIPTION(DRIVER_DESC);
+MODULE_DESCRIPTION("Prolific PL2303 USB to serial adaptor driver");
 MODULE_LICENSE("GPL");