diff options
Diffstat (limited to 'drivers/net/e1000e/ich8lan.c')
| -rw-r--r-- | drivers/net/e1000e/ich8lan.c | 2225 |
1 files changed, 0 insertions, 2225 deletions
diff --git a/drivers/net/e1000e/ich8lan.c b/drivers/net/e1000e/ich8lan.c deleted file mode 100644 index 0ae39550768..00000000000 --- a/drivers/net/e1000e/ich8lan.c +++ /dev/null @@ -1,2225 +0,0 @@ -/******************************************************************************* - - Intel PRO/1000 Linux driver - Copyright(c) 1999 - 2007 Intel Corporation. - - This program is free software; you can redistribute it and/or modify it - under the terms and conditions of the GNU General Public License, - version 2, as published by the Free Software Foundation. - - This program is distributed in the hope it will be useful, but WITHOUT - ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or - FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for - more details. - - You should have received a copy of the GNU General Public License along with - this program; if not, write to the Free Software Foundation, Inc., - 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. - - The full GNU General Public License is included in this distribution in - the file called "COPYING". - - Contact Information: - Linux NICS <linux.nics@intel.com> - e1000-devel Mailing List <e1000-devel@lists.sourceforge.net> - Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 - -*******************************************************************************/ - -/* - * 82562G-2 10/100 Network Connection - * 82562GT 10/100 Network Connection - * 82562GT-2 10/100 Network Connection - * 82562V 10/100 Network Connection - * 82562V-2 10/100 Network Connection - * 82566DC-2 Gigabit Network Connection - * 82566DC Gigabit Network Connection - * 82566DM-2 Gigabit Network Connection - * 82566DM Gigabit Network Connection - * 82566MC Gigabit Network Connection - * 82566MM Gigabit Network Connection - */ - -#include <linux/netdevice.h> -#include <linux/ethtool.h> -#include <linux/delay.h> -#include <linux/pci.h> - -#include "e1000.h" - -#define ICH_FLASH_GFPREG 0x0000 -#define ICH_FLASH_HSFSTS 0x0004 -#define ICH_FLASH_HSFCTL 0x0006 -#define ICH_FLASH_FADDR 0x0008 -#define ICH_FLASH_FDATA0 0x0010 - -#define ICH_FLASH_READ_COMMAND_TIMEOUT 500 -#define ICH_FLASH_WRITE_COMMAND_TIMEOUT 500 -#define ICH_FLASH_ERASE_COMMAND_TIMEOUT 3000000 -#define ICH_FLASH_LINEAR_ADDR_MASK 0x00FFFFFF -#define ICH_FLASH_CYCLE_REPEAT_COUNT 10 - -#define ICH_CYCLE_READ 0 -#define ICH_CYCLE_WRITE 2 -#define ICH_CYCLE_ERASE 3 - -#define FLASH_GFPREG_BASE_MASK 0x1FFF -#define FLASH_SECTOR_ADDR_SHIFT 12 - -#define ICH_FLASH_SEG_SIZE_256 256 -#define ICH_FLASH_SEG_SIZE_4K 4096 -#define ICH_FLASH_SEG_SIZE_8K 8192 -#define ICH_FLASH_SEG_SIZE_64K 65536 - - -#define E1000_ICH_FWSM_RSPCIPHY 0x00000040 /* Reset PHY on PCI Reset */ - -#define E1000_ICH_MNG_IAMT_MODE 0x2 - -#define ID_LED_DEFAULT_ICH8LAN ((ID_LED_DEF1_DEF2 << 12) | \ - (ID_LED_DEF1_OFF2 << 8) | \ - (ID_LED_DEF1_ON2 << 4) | \ - (ID_LED_DEF1_DEF2)) - -#define E1000_ICH_NVM_SIG_WORD 0x13 -#define E1000_ICH_NVM_SIG_MASK 0xC000 - -#define E1000_ICH8_LAN_INIT_TIMEOUT 1500 - -#define E1000_FEXTNVM_SW_CONFIG 1 -#define E1000_FEXTNVM_SW_CONFIG_ICH8M (1 << 27) /* Bit redefined for ICH8M :/ */ - -#define PCIE_ICH8_SNOOP_ALL PCIE_NO_SNOOP_ALL - -#define E1000_ICH_RAR_ENTRIES 7 - -#define PHY_PAGE_SHIFT 5 -#define PHY_REG(page, reg) (((page) << PHY_PAGE_SHIFT) | \ - ((reg) & MAX_PHY_REG_ADDRESS)) -#define IGP3_KMRN_DIAG PHY_REG(770, 19) /* KMRN Diagnostic */ -#define IGP3_VR_CTRL PHY_REG(776, 18) /* Voltage Regulator Control */ - -#define IGP3_KMRN_DIAG_PCS_LOCK_LOSS 0x0002 -#define IGP3_VR_CTRL_DEV_POWERDOWN_MODE_MASK 0x0300 -#define IGP3_VR_CTRL_MODE_SHUTDOWN 0x0200 - -/* ICH GbE Flash Hardware Sequencing Flash Status Register bit breakdown */ -/* Offset 04h HSFSTS */ -union ich8_hws_flash_status { - struct ich8_hsfsts { - u16 flcdone :1; /* bit 0 Flash Cycle Done */ - u16 flcerr :1; /* bit 1 Flash Cycle Error */ - u16 dael :1; /* bit 2 Direct Access error Log */ - u16 berasesz :2; /* bit 4:3 Sector Erase Size */ - u16 flcinprog :1; /* bit 5 flash cycle in Progress */ - u16 reserved1 :2; /* bit 13:6 Reserved */ - u16 reserved2 :6; /* bit 13:6 Reserved */ - u16 fldesvalid :1; /* bit 14 Flash Descriptor Valid */ - u16 flockdn :1; /* bit 15 Flash Config Lock-Down */ - } hsf_status; - u16 regval; -}; - -/* ICH GbE Flash Hardware Sequencing Flash control Register bit breakdown */ -/* Offset 06h FLCTL */ -union ich8_hws_flash_ctrl { - struct ich8_hsflctl { - u16 flcgo :1; /* 0 Flash Cycle Go */ - u16 flcycle :2; /* 2:1 Flash Cycle */ - u16 reserved :5; /* 7:3 Reserved */ - u16 fldbcount :2; /* 9:8 Flash Data Byte Count */ - u16 flockdn :6; /* 15:10 Reserved */ - } hsf_ctrl; - u16 regval; -}; - -/* ICH Flash Region Access Permissions */ -union ich8_hws_flash_regacc { - struct ich8_flracc { - u32 grra :8; /* 0:7 GbE region Read Access */ - u32 grwa :8; /* 8:15 GbE region Write Access */ - u32 gmrag :8; /* 23:16 GbE Master Read Access Grant */ - u32 gmwag :8; /* 31:24 GbE Master Write Access Grant */ - } hsf_flregacc; - u16 regval; -}; - -static s32 e1000_setup_link_ich8lan(struct e1000_hw *hw); -static void e1000_clear_hw_cntrs_ich8lan(struct e1000_hw *hw); -static void e1000_initialize_hw_bits_ich8lan(struct e1000_hw *hw); -static s32 e1000_check_polarity_ife_ich8lan(struct e1000_hw *hw); -static s32 e1000_erase_flash_bank_ich8lan(struct e1000_hw *hw, u32 bank); -static s32 e1000_retry_write_flash_byte_ich8lan(struct e1000_hw *hw, - u32 offset, u8 byte); -static s32 e1000_read_flash_word_ich8lan(struct e1000_hw *hw, u32 offset, - u16 *data); -static s32 e1000_read_flash_data_ich8lan(struct e1000_hw *hw, u32 offset, - u8 size, u16 *data); -static s32 e1000_setup_copper_link_ich8lan(struct e1000_hw *hw); -static s32 e1000_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw); - -static inline u16 __er16flash(struct e1000_hw *hw, unsigned long reg) -{ - return readw(hw->flash_address + reg); -} - -static inline u32 __er32flash(struct e1000_hw *hw, unsigned long reg) -{ - return readl(hw->flash_address + reg); -} - -static inline void __ew16flash(struct e1000_hw *hw, unsigned long reg, u16 val) -{ - writew(val, hw->flash_address + reg); -} - -static inline void __ew32flash(struct e1000_hw *hw, unsigned long reg, u32 val) -{ - writel(val, hw->flash_address + reg); -} - -#define er16flash(reg) __er16flash(hw, (reg)) -#define er32flash(reg) __er32flash(hw, (reg)) -#define ew16flash(reg,val) __ew16flash(hw, (reg), (val)) -#define ew32flash(reg,val) __ew32flash(hw, (reg), (val)) - -/** - * e1000_init_phy_params_ich8lan - Initialize PHY function pointers - * @hw: pointer to the HW structure - * - * Initialize family-specific PHY parameters and function pointers. - **/ -static s32 e1000_init_phy_params_ich8lan(struct e1000_hw *hw) -{ - struct e1000_phy_info *phy = &hw->phy; - s32 ret_val; - u16 i = 0; - - phy->addr = 1; - phy->reset_delay_us = 100; - - phy->id = 0; - while ((e1000_phy_unknown == e1000e_get_phy_type_from_id(phy->id)) && - (i++ < 100)) { - msleep(1); - ret_val = e1000e_get_phy_id(hw); - if (ret_val) - return ret_val; - } - - /* Verify phy id */ - switch (phy->id) { - case IGP03E1000_E_PHY_ID: - phy->type = e1000_phy_igp_3; - phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT; - break; - case IFE_E_PHY_ID: - case IFE_PLUS_E_PHY_ID: - case IFE_C_E_PHY_ID: - phy->type = e1000_phy_ife; - phy->autoneg_mask = E1000_ALL_NOT_GIG; - break; - default: - return -E1000_ERR_PHY; - break; - } - - return 0; -} - -/** - * e1000_init_nvm_params_ich8lan - Initialize NVM function pointers - * @hw: pointer to the HW structure - * - * Initialize family-specific NVM parameters and function - * pointers. - **/ -static s32 e1000_init_nvm_params_ich8lan(struct e1000_hw *hw) -{ - struct e1000_nvm_info *nvm = &hw->nvm; - struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; - u32 gfpreg; - u32 sector_base_addr; - u32 sector_end_addr; - u16 i; - - /* Can't read flash registers if the register set isn't mapped. - */ - if (!hw->flash_address) { - hw_dbg(hw, "ERROR: Flash registers not mapped\n"); - return -E1000_ERR_CONFIG; - } - - nvm->type = e1000_nvm_flash_sw; - - gfpreg = er32flash(ICH_FLASH_GFPREG); - - /* sector_X_addr is a "sector"-aligned address (4096 bytes) - * Add 1 to sector_end_addr since this sector is included in - * the overall size. */ - sector_base_addr = gfpreg & FLASH_GFPREG_BASE_MASK; - sector_end_addr = ((gfpreg >> 16) & FLASH_GFPREG_BASE_MASK) + 1; - - /* flash_base_addr is byte-aligned */ - nvm->flash_base_addr = sector_base_addr << FLASH_SECTOR_ADDR_SHIFT; - - /* find total size of the NVM, then cut in half since the total - * size represents two separate NVM banks. */ - nvm->flash_bank_size = (sector_end_addr - sector_base_addr) - << FLASH_SECTOR_ADDR_SHIFT; - nvm->flash_bank_size /= 2; - /* Adjust to word count */ - nvm->flash_bank_size /= sizeof(u16); - - nvm->word_size = E1000_ICH8_SHADOW_RAM_WORDS; - - /* Clear shadow ram */ - for (i = 0; i < nvm->word_size; i++) { - dev_spec->shadow_ram[i].modified = 0; - dev_spec->shadow_ram[i].value = 0xFFFF; - } - - return 0; -} - -/** - * e1000_init_mac_params_ich8lan - Initialize MAC function pointers - * @hw: pointer to the HW structure - * - * Initialize family-specific MAC parameters and function - * pointers. - **/ -static s32 e1000_init_mac_params_ich8lan(struct e1000_adapter *adapter) -{ - struct e1000_hw *hw = &adapter->hw; - struct e1000_mac_info *mac = &hw->mac; - - /* Set media type function pointer */ - hw->media_type = e1000_media_type_copper; - - /* Set mta register count */ - mac->mta_reg_count = 32; - /* Set rar entry count */ - mac->rar_entry_count = E1000_ICH_RAR_ENTRIES; - if (mac->type == e1000_ich8lan) - mac->rar_entry_count--; - /* Set if manageability features are enabled. */ - mac->arc_subsystem_valid = 1; - - /* Enable PCS Lock-loss workaround for ICH8 */ - if (mac->type == e1000_ich8lan) - e1000e_set_kmrn_lock_loss_workaround_ich8lan(hw, 1); - - return 0; -} - -static s32 e1000_get_invariants_ich8lan(struct e1000_adapter *adapter) -{ - struct e1000_hw *hw = &adapter->hw; - s32 rc; - - rc = e1000_init_mac_params_ich8lan(adapter); - if (rc) - return rc; - - rc = e1000_init_nvm_params_ich8lan(hw); - if (rc) - return rc; - - rc = e1000_init_phy_params_ich8lan(hw); - if (rc) - return rc; - - if ((adapter->hw.mac.type == e1000_ich8lan) && - (adapter->hw.phy.type == e1000_phy_igp_3)) - adapter->flags |= FLAG_LSC_GIG_SPEED_DROP; - - return 0; -} - -/** - * e1000_acquire_swflag_ich8lan - Acquire software control flag - * @hw: pointer to the HW structure - * - * Acquires the software control flag for performing NVM and PHY - * operations. This is a function pointer entry point only called by - * read/write routines for the PHY and NVM parts. - **/ -static s32 e1000_acquire_swflag_ich8lan(struct e1000_hw *hw) -{ - u32 extcnf_ctrl; - u32 timeout = PHY_CFG_TIMEOUT; - - while (timeout) { - extcnf_ctrl = er32(EXTCNF_CTRL); - extcnf_ctrl |= E1000_EXTCNF_CTRL_SWFLAG; - ew32(EXTCNF_CTRL, extcnf_ctrl); - - extcnf_ctrl = er32(EXTCNF_CTRL); - if (extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG) - break; - mdelay(1); - timeout--; - } - - if (!timeout) { - hw_dbg(hw, "FW or HW has locked the resource for too long.\n"); - return -E1000_ERR_CONFIG; - } - - return 0; -} - -/** - * e1000_release_swflag_ich8lan - Release software control flag - * @hw: pointer to the HW structure - * - * Releases the software control flag for performing NVM and PHY operations. - * This is a function pointer entry point only called by read/write - * routines for the PHY and NVM parts. - **/ -static void e1000_release_swflag_ich8lan(struct e1000_hw *hw) -{ - u32 extcnf_ctrl; - - extcnf_ctrl = er32(EXTCNF_CTRL); - extcnf_ctrl &= ~E1000_EXTCNF_CTRL_SWFLAG; - ew32(EXTCNF_CTRL, extcnf_ctrl); -} - -/** - * e1000_check_reset_block_ich8lan - Check if PHY reset is blocked - * @hw: pointer to the HW structure - * - * Checks if firmware is blocking the reset of the PHY. - * This is a function pointer entry point only called by - * reset routines. - **/ -static s32 e1000_check_reset_block_ich8lan(struct e1000_hw *hw) -{ - u32 fwsm; - - fwsm = er32(FWSM); - - return (fwsm & E1000_ICH_FWSM_RSPCIPHY) ? 0 : E1000_BLK_PHY_RESET; -} - -/** - * e1000_phy_force_speed_duplex_ich8lan - Force PHY speed & duplex - * @hw: pointer to the HW structure - * - * Forces the speed and duplex settings of the PHY. - * This is a function pointer entry point only called by - * PHY setup routines. - **/ -static s32 e1000_phy_force_speed_duplex_ich8lan(struct e1000_hw *hw) -{ - struct e1000_phy_info *phy = &hw->phy; - s32 ret_val; - u16 data; - bool link; - - if (phy->type != e1000_phy_ife) { - ret_val = e1000e_phy_force_speed_duplex_igp(hw); - return ret_val; - } - - ret_val = e1e_rphy(hw, PHY_CONTROL, &data); - if (ret_val) - return ret_val; - - e1000e_phy_force_speed_duplex_setup(hw, &data); - - ret_val = e1e_wphy(hw, PHY_CONTROL, data); - if (ret_val) - return ret_val; - - /* Disable MDI-X support for 10/100 */ - ret_val = e1e_rphy(hw, IFE_PHY_MDIX_CONTROL, &data); - if (ret_val) - return ret_val; - - data &= ~IFE_PMC_AUTO_MDIX; - data &= ~IFE_PMC_FORCE_MDIX; - - ret_val = e1e_wphy(hw, IFE_PHY_MDIX_CONTROL, data); - if (ret_val) - return ret_val; - - hw_dbg(hw, "IFE PMC: %X\n", data); - - udelay(1); - - if (phy->wait_for_link) { - hw_dbg(hw, "Waiting for forced speed/duplex link on IFE phy.\n"); - - ret_val = e1000e_phy_has_link_generic(hw, - PHY_FORCE_LIMIT, - 100000, - &link); - if (ret_val) - return ret_val; - - if (!link) - hw_dbg(hw, "Link taking longer than expected.\n"); - - /* Try once more */ - ret_val = e1000e_phy_has_link_generic(hw, - PHY_FORCE_LIMIT, - 100000, - &link); - if (ret_val) - return ret_val; - } - - return 0; -} - -/** - * e1000_phy_hw_reset_ich8lan - Performs a PHY reset - * @hw: pointer to the HW structure - * - * Resets the PHY - * This is a function pointer entry point called by drivers - * or other shared routines. - **/ -static s32 e1000_phy_hw_reset_ich8lan(struct e1000_hw *hw) -{ - struct e1000_phy_info *phy = &hw->phy; - u32 i; - u32 data, cnf_size, cnf_base_addr, sw_cfg_mask; - s32 ret_val; - u16 loop = E1000_ICH8_LAN_INIT_TIMEOUT; - u16 word_addr, reg_data, reg_addr, phy_page = 0; - - ret_val = e1000e_phy_hw_reset_generic(hw); - if (ret_val) - return ret_val; - - /* Initialize the PHY from the NVM on ICH platforms. This - * is needed due to an issue where the NVM configuration is - * not properly autoloaded after power transitions. - * Therefore, after each PHY reset, we will load the - * configuration data out of the NVM manually. - */ - if (hw->mac.type == e1000_ich8lan && phy->type == e1000_phy_igp_3) { - struct e1000_adapter *adapter = hw->adapter; - - /* Check if SW needs configure the PHY */ - if ((adapter->pdev->device == E1000_DEV_ID_ICH8_IGP_M_AMT) || - (adapter->pdev->device == E1000_DEV_ID_ICH8_IGP_M)) - sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG_ICH8M; - else - sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG; - - data = er32(FEXTNVM); - if (!(data & sw_cfg_mask)) - return 0; - - /* Wait for basic configuration completes before proceeding*/ - do { - data = er32(STATUS); - data &= E1000_STATUS_LAN_INIT_DONE; - udelay(100); - } while ((!data) && --loop); - - /* If basic configuration is incomplete before the above loop - * count reaches 0, loading the configuration from NVM will - * leave the PHY in a bad state possibly resulting in no link. - */ - if (loop == 0) { - hw_dbg(hw, "LAN_INIT_DONE not set, increase timeout\n"); - } - - /* Clear the Init Done bit for the next init event */ - data = er32(STATUS); - data &= ~E1000_STATUS_LAN_INIT_DONE; - ew32(STATUS, data); - - /* Make sure HW does not configure LCD from PHY - * extended configuration before SW configuration */ - data = er32(EXTCNF_CTRL); - if (data & E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE) - return 0; - - cnf_size = er32(EXTCNF_SIZE); - cnf_size &= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK; - cnf_size >>= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT; - if (!cnf_size) - return 0; - - cnf_base_addr = data & E1000_EXTCNF_CTRL_EXT_CNF_POINTER_MASK; - cnf_base_addr >>= E1000_EXTCNF_CTRL_EXT_CNF_POINTER_SHIFT; - - /* Configure LCD from extended configuration - * region. */ - - /* cnf_base_addr is in DWORD */ - word_addr = (u16)(cnf_base_addr << 1); - - for (i = 0; i < cnf_size; i++) { - ret_val = e1000_read_nvm(hw, - (word_addr + i * 2), - 1, - ®_data); - if (ret_val) - return ret_val; - - ret_val = e1000_read_nvm(hw, - (word_addr + i * 2 + 1), - 1, - ®_addr); - if (ret_val) - return ret_val; - - /* Save off the PHY page for future writes. */ - if (reg_addr == IGP01E1000_PHY_PAGE_SELECT) { - phy_page = reg_data; - continue; - } - - reg_addr |= phy_page; - - ret_val = e1e_wphy(hw, (u32)reg_addr, reg_data); - if (ret_val) - return ret_val; - } - } - - return 0; -} - -/** - * e1000_get_phy_info_ife_ich8lan - Retrieves various IFE PHY states - * @hw: pointer to the HW structure - * - * Populates "phy" structure with various feature states. - * This function is only called by other family-specific - * routines. - **/ -static s32 e1000_get_phy_info_ife_ich8lan(struct e1000_hw *hw) -{ - struct e1000_phy_info *phy = &hw->phy; - s32 ret_val; - u16 data; - bool link; - - ret_val = e1000e_phy_has_link_generic(hw, 1, 0, &link); - if (ret_val) - return ret_val; - - if (!link) { - hw_dbg(hw, "Phy info is only valid if link is up\n"); - return -E1000_ERR_CONFIG; - } - - ret_val = e1e_rphy(hw, IFE_PHY_SPECIAL_CONTROL, &data); - if (ret_val) - return ret_val; - phy->polarity_correction = (!(data & IFE_PSC_AUTO_POLARITY_DISABLE)); - - if (phy->polarity_correction) { - ret_val = e1000_check_polarity_ife_ich8lan(hw); - if (ret_val) - return ret_val; - } else { - /* Polarity is forced */ - phy->cable_polarity = (data & IFE_PSC_FORCE_POLARITY) - ? e1000_rev_polarity_reversed - : e1000_rev_polarity_normal; - } - - ret_val = e1e_rphy(hw, IFE_PHY_MDIX_CONTROL, &data); - if (ret_val) - return ret_val; - - phy->is_mdix = (data & IFE_PMC_MDIX_STATUS); - - /* The following parameters are undefined for 10/100 operation. */ - phy->cable_length = E1000_CABLE_LENGTH_UNDEFINED; - phy->local_rx = e1000_1000t_rx_status_undefined; - phy->remote_rx = e1000_1000t_rx_status_undefined; - - return 0; -} - -/** - * e1000_get_phy_info_ich8lan - Calls appropriate PHY type get_phy_info - * @hw: pointer to the HW structure - * - * Wrapper for calling the get_phy_info routines for the appropriate phy type. - * This is a function pointer entry point called by drivers - * or other shared routines. - **/ -static s32 e1000_get_phy_info_ich8lan(struct e1000_hw *hw) -{ - switch (hw->phy.type) { - case e1000_phy_ife: - return e1000_get_phy_info_ife_ich8lan(hw); - break; - case e1000_phy_igp_3: - return e1000e_get_phy_info_igp(hw); - break; - default: - break; - } - - return -E1000_ERR_PHY_TYPE; -} - -/** - * e1000_check_polarity_ife_ich8lan - Check cable polarity for IFE PHY - * @hw: pointer to the HW structure - * - * Polarity is determined on the polarity reversal feature being enabled. - * This function is only called by other family-specific - * routines. - **/ -static s32 e1000_check_polarity_ife_ich8lan(struct e1000_hw *hw) -{ - struct e1000_phy_info *phy = &hw->phy; - s32 ret_val; - u16 phy_data, offset, mask; - - /* Polarity is determined based on the reversal feature - * being enabled. - */ - if (phy->polarity_correction) { - offset = IFE_PHY_EXTENDED_STATUS_CONTROL; - mask = IFE_PESC_POLARITY_REVERSED; - } else { - offset = IFE_PHY_SPECIAL_CONTROL; - mask = IFE_PSC_FORCE_POLARITY; - } - - ret_val = e1e_rphy(hw, offset, &phy_data); - - if (!ret_val) - phy->cable_polarity = (phy_data & mask) - ? e1000_rev_polarity_reversed - : e1000_rev_polarity_normal; - - return ret_val; -} - -/** - * e1000_set_d0_lplu_state_ich8lan - Set Low Power Linkup D0 state - * @hw: pointer to the HW structure - * @active: TRUE to enable LPLU, FALSE to disable - * - * Sets the LPLU D0 state according to the active flag. When - * activating LPLU this function also disables smart speed - * and vice versa. LPLU will not be activated unless the - * device autonegotiation advertisement meets standards of - * either 10 or 10/100 or 10/100/1000 at all duplexes. - * This is a function pointer entry point only called by - * PHY setup routines. - **/ -static s32 e1000_set_d0_lplu_state_ich8lan(struct e1000_hw *hw, bool active) -{ - struct e1000_phy_info *phy = &hw->phy; - u32 phy_ctrl; - s32 ret_val = 0; - u16 data; - - if (phy->type != e1000_phy_igp_3) - return ret_val; - - phy_ctrl = er32(PHY_CTRL); - - if (active) { - phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU; - ew32(PHY_CTRL, phy_ctrl); - - /* Call gig speed drop workaround on LPLU before accessing - * any PHY registers */ - if ((hw->mac.type == e1000_ich8lan) && - (hw->phy.type == e1000_phy_igp_3)) - e1000e_gig_downshift_workaround_ich8lan(hw); - - /* When LPLU is enabled, we should disable SmartSpeed */ - ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG, &data); - data &= ~IGP01E1000_PSCFR_SMART_SPEED; - ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG, data); - if (ret_val) - return ret_val; - } else { - phy_ctrl &= ~E1000_PHY_CTRL_D0A_LPLU; - ew32(PHY_CTRL, phy_ctrl); - - /* LPLU and SmartSpeed are mutually exclusive. LPLU is used - * during Dx states where the power conservation is most - * important. During driver activity we should enable - * SmartSpeed, so performance is maintained. */ - if (phy->smart_speed == e1000_smart_speed_on) { - ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG, - &data); - if (ret_val) - return ret_val; - - data |= IGP01E1000_PSCFR_SMART_SPEED; - ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG, - data); - if (ret_val) - return ret_val; - } else if (phy->smart_speed == e1000_smart_speed_off) { - ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG, - &data); - if (ret_val) - return ret_val; - - data &= ~IGP01E1000_PSCFR_SMART_SPEED; - ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG, - data); - if (ret_val) - return ret_val; - } - } - - return 0; -} - -/** - * e1000_set_d3_lplu_state_ich8lan - Set Low Power Linkup D3 state - * @hw: pointer to the HW structure - * @active: TRUE to enable LPLU, FALSE to disable - * - * Sets the LPLU D3 state according to the active flag. When - * activating LPLU this function also disables smart speed - * and vice versa. LPLU will not be activated unless the - * device autonegotiation advertisement meets standards of - * either 10 or 10/100 or 10/100/1000 at all duplexes. - * This is a function pointer entry point only called by - * PHY setup routines. - **/ -static s32 e1000_set_d3_lplu_state_ich8lan(struct e1000_hw *hw, bool active) -{ - struct e1000_phy_info *phy = &hw->phy; - u32 phy_ctrl; - s32 ret_val; - u16 data; - - phy_ctrl = er32(PHY_CTRL); - - if (!active) { - phy_ctrl &= ~E1000_PHY_CTRL_NOND0A_LPLU; - ew32(PHY_CTRL, phy_ctrl); - /* LPLU and SmartSpeed are mutually exclusive. LPLU is used - * during Dx states where the power conservation is most - * important. During driver activity we should enable - * SmartSpeed, so performance is maintained. */ - if (phy->smart_speed == e1000_smart_speed_on) { - ret_val = e1e_rphy(hw, - IGP01E1000_PHY_PORT_CONFIG, - &data); - if (ret_val) - return ret_val; - - data |= IGP01E1000_PSCFR_SMART_SPEED; - ret_val = e1e_wphy(hw, - IGP01E1000_PHY_PORT_CONFIG, - data); - if (ret_val) - return ret_val; - } else if (phy->smart_speed == e1000_smart_speed_off) { - ret_val = e1e_rphy(hw, - IGP01E1000_PHY_PORT_CONFIG, - &data); - if (ret_val) - return ret_val; - - data &= ~IGP01E1000_PSCFR_SMART_SPEED; - ret_val = e1e_wphy(hw, - IGP01E1000_PHY_PORT_CONFIG, - data); - if (ret_val) - return ret_val; - } - } else if ((phy->autoneg_advertised == E1000_ALL_SPEED_DUPLEX) || - (phy->autoneg_advertised == E1000_ALL_NOT_GIG) || - (phy->autoneg_advertised == E1000_ALL_10_SPEED)) { - phy_ctrl |= E1000_PHY_CTRL_NOND0A_LPLU; - ew32(PHY_CTRL, phy_ctrl); - - /* Call gig speed drop workaround on LPLU before accessing - * any PHY registers */ - if ((hw->mac.type == e1000_ich8lan) && - (hw->phy.type == e1000_phy_igp_3)) - e1000e_gig_downshift_workaround_ich8lan(hw); - - /* When LPLU is enabled, we should disable SmartSpeed */ - ret_val = e1e_rphy(hw, - IGP01E1000_PHY_PORT_CONFIG, - &data); - if (ret_val) - return ret_val; - - data &= ~IGP01E1000_PSCFR_SMART_SPEED; - ret_val = e1e_wphy(hw, - IGP01E1000_PHY_PORT_CONFIG, - data); - } - - return 0; -} - -/** - * e1000_read_nvm_ich8lan - Read word(s) from the NVM - * @hw: pointer to the HW structure - * @offset: The offset (in bytes) of the word(s) to read. - * @words: Size of data to read in words - * @data: Pointer to the word(s) to read at offset. - * - * Reads a word(s) from the NVM using the flash access registers. - **/ -static s32 e1000_read_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words, - u16 *data) -{ - struct e1000_nvm_info *nvm = &hw->nvm; - struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; - u32 act_offset; - s32 ret_val; - u16 i, word; - - if ((offset >= nvm->word_size) || (words > nvm->word_size - offset) || - (words == 0)) { - hw_dbg(hw, "nvm parameter(s) out of bounds\n"); - return -E1000_ERR_NVM; - } - - ret_val = e1000_acquire_swflag_ich8lan(hw); - if (ret_val) - return ret_val; - - /* Start with the bank offset, then add the relative offset. */ - act_offset = (er32(EECD) & E1000_EECD_SEC1VAL) - ? nvm->flash_bank_size - : 0; - act_offset += offset; - - for (i = 0; i < words; i++) { - if ((dev_spec->shadow_ram) && - (dev_spec->shadow_ram[offset+i].modified)) { - data[i] = dev_spec->shadow_ram[offset+i].value; - } else { - ret_val = e1000_read_flash_word_ich8lan(hw, - act_offset + i, - &word); - if (ret_val) - break; - data[i] = word; - } - } - - e1000_release_swflag_ich8lan(hw); - - return ret_val; -} - -/** - * e1000_flash_cycle_init_ich8lan - Initialize flash - * @hw: pointer to the HW structure - * - * This function does initial flash setup so that a new read/write/erase cycle - * can be started. - **/ -static s32 e1000_flash_cycle_init_ich8lan(struct e1000_hw *hw) -{ - union ich8_hws_flash_status hsfsts; - s32 ret_val = -E1000_ERR_NVM; - s32 i = 0; - - hsfsts.regval = er16flash(ICH_FLASH_HSFSTS); - - /* Check if the flash descriptor is valid */ - if (hsfsts.hsf_status.fldesvalid == 0) { - hw_dbg(hw, "Flash descriptor invalid. " - "SW Sequencing must be used."); - return -E1000_ERR_NVM; - } - - /* Clear FCERR and DAEL in hw status by writing 1 */ - hsfsts.hsf_status.flcerr = 1; - hsfsts.hsf_status.dael = 1; - - ew16flash(ICH_FLASH_HSFSTS, hsfsts.regval); - - /* Either we should have a hardware SPI cycle in progress - * bit to check against, in order to start a new cycle or - * FDONE bit should be changed in the hardware so that it - * is 1 after hardware reset, which can then be used as an - * indication whether a cycle is in progress or has been - * completed. - */ - - if (hsfsts.hsf_status.flcinprog == 0) { - /* There is no cycle running at present, - * so we can start a cycle */ - /* Begin by setting Flash Cycle Done. */ - hsfsts.hsf_status.flcdone = 1; - ew16flash(ICH_FLASH_HSFSTS, hsfsts.regval); - ret_val = 0; - } else { - /* otherwise poll for sometime so the current - * cycle has a chance to end before giving up. */ - for (i = 0; i < ICH_FLASH_READ_COMMAND_TIMEOUT; i++) { - hsfsts.regval = __er16flash(hw, ICH_FLASH_HSFSTS); - if (hsfsts.hsf_status.flcinprog == 0) { - ret_val = 0; - break; - } - udelay(1); - } - if (ret_val == 0) { - /* Successful in waiting for previous cycle to timeout, - * now set the Flash Cycle Done. */ - hsfsts.hsf_status.flcdone = 1; - ew16flash(ICH_FLASH_HSFSTS, hsfsts.regval); - } else { - hw_dbg(hw, "Flash controller busy, cannot get access"); - } - } - - return ret_val; -} - -/** - * e1000_flash_cycle_ich8lan - Starts flash cycle (read/write/erase) - * @hw: pointer to the HW structure - * @timeout: maximum time to wait for completion - * - * This function starts a flash cycle and waits for its completion. - **/ -static s32 e1000_flash_cycle_ich8lan(struct e1000_hw *hw, u32 timeout) -{ - union ich8_hws_flash_ctrl hsflctl; - union ich8_hws_flash_status hsfsts; - s32 ret_val = -E1000_ERR_NVM; - u32 i = 0; - - /* Start a cycle by writing 1 in Flash Cycle Go in Hw Flash Control */ - hsflctl.regval = er16flash(ICH_FLASH_HSFCTL); - hsflctl.hsf_ctrl.flcgo = 1; - ew16flash(ICH_FLASH_HSFCTL, hsflctl.regval); - - /* wait till FDONE bit is set to 1 */ - do { - hsfsts.regval = er16flash(ICH_FLASH_HSFSTS); - if (hsfsts.hsf_status.flcdone == 1) - break; - udelay(1); - } while (i++ < timeout); - - if (hsfsts.hsf_status.flcdone == 1 && hsfsts.hsf_status.flcerr == 0) - return 0; - - return ret_val; -} - -/** - * e1000_read_flash_word_ich8lan - Read word from flash - * @hw: pointer to the HW structure - * @offset: offset to data location - * @data: pointer to the location for storing the data - * - * Reads the flash word at offset into data. Offset is converted - * to bytes before read. - **/ -static s32 e1000_read_flash_word_ich8lan(struct e1000_hw *hw, u32 offset, - u16 *data) -{ - /* Must convert offset into bytes. */ - offset <<= 1; - - return e1000_read_flash_data_ich8lan(hw, offset, 2, data); -} - -/** - * e1000_read_flash_data_ich8lan - Read byte or word from NVM - * @hw: pointer to the HW structure - * @offset: The offset (in bytes) of the byte or word to read. - * @size: Size of data to read, 1=byte 2=word - * @data: Pointer to the word to store the value read. - * - * Reads a byte or word from the NVM using the flash access registers. - **/ -static s32 e1000_read_flash_data_ich8lan(struct e1000_hw *hw, u32 offset, - u8 size, u16 *data) -{ - union ich8_hws_flash_status hsfsts; - union ich8_hws_flash_ctrl hsflctl; - u32 flash_linear_addr; - u32 flash_data = 0; - s32 ret_val = -E1000_ERR_NVM; - u8 count = 0; - - if (size < 1 || size > 2 || offset > ICH_FLASH_LINEAR_ADDR_MASK) - return -E1000_ERR_NVM; - - flash_linear_addr = (ICH_FLASH_LINEAR_ADDR_MASK & offset) + - hw->nvm.flash_base_addr; - - do { - udelay(1); - /* Steps */ - ret_val = e1000_flash_cycle_init_ich8lan(hw); - if (ret_val != 0) - break; - - hsflctl.regval = er16flash(ICH_FLASH_HSFCTL); - /* 0b/1b corresponds to 1 or 2 byte size, respectively. */ - hsflctl.hsf_ctrl.fldbcount = size - 1; - hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_READ; - ew16flash(ICH_FLASH_HSFCTL, hsflctl.regval); - - ew32flash(ICH_FLASH_FADDR, flash_linear_addr); - - ret_val = e1000_flash_cycle_ich8lan(hw, - ICH_FLASH_READ_COMMAND_TIMEOUT); - - /* Check if FCERR is set to 1, if set to 1, clear it - * and try the whole sequence a few more times, else - * read in (shift in) the Flash Data0, the order is - * least significant byte first msb to lsb */ - if (ret_val == 0) { - flash_data = er32flash(ICH_FLASH_FDATA0); - if (size == 1) { - *data = (u8)(flash_data & 0x000000FF); - } else if (size == 2) { - *data = (u16)(flash_data & 0x0000FFFF); - } - break; - } else { - /* If we've gotten here, then things are probably - * completely hosed, but if the error condition is - * detected, it won't hurt to give it another try... - * ICH_FLASH_CYCLE_REPEAT_COUNT times. - */ - hsfsts.regval = er16flash(ICH_FLASH_HSFSTS); - if (hsfsts.hsf_status.flcerr == 1) { - /* Repeat for some time before giving up. */ - continue; - } else if (hsfsts.hsf_status.flcdone == 0) { - hw_dbg(hw, "Timeout error - flash cycle " - "did not complete."); - break; - } - } - } while (count++ < ICH_FLASH_CYCLE_REPEAT_COUNT); - - return ret_val; -} - -/** - * e1000_write_nvm_ich8lan - Write word(s) to the NVM - * @hw: pointer to the HW structure - * @offset: The offset (in bytes) of the word(s) to write. - * @words: Size of data to write in words - * @data: Pointer to the word(s) to write at offset. - * - * Writes a byte or word to the NVM using the flash access registers. - **/ -static s32 e1000_write_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words, - u16 *data) -{ - struct e1000_nvm_info *nvm = &hw->nvm; - struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; - s32 ret_val; - u16 i; - - if ((offset >= nvm->word_size) || (words > nvm->word_size - offset) || - (words == 0)) { - hw_dbg(hw, "nvm parameter(s) out of bounds\n"); - return -E1000_ERR_NVM; - } - - ret_val = e1000_acquire_swflag_ich8lan(hw); - if (ret_val) - return ret_val; - - for (i = 0; i < words; i++) { - dev_spec->shadow_ram[offset+i].modified = 1; - dev_spec->shadow_ram[offset+i].value = data[i]; - } - - e1000_release_swflag_ich8lan(hw); - - return 0; -} - -/** - * e1000_update_nvm_checksum_ich8lan - Update the checksum for NVM - * @hw: pointer to the HW structure - * - * The NVM checksum is updated by calling the generic update_nvm_checksum, - * which writes the checksum to the shadow ram. The changes in the shadow - * ram are then committed to the EEPROM by processing each bank at a time - * checking for the modified bit and writing only the pending changes. - * After a successful commit, the shadow ram is cleared and is ready for - * future writes. - **/ -static s32 e1000_update_nvm_checksum_ich8lan(struct e1000_hw *hw) -{ - struct e1000_nvm_info *nvm = &hw->nvm; - struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; - u32 i, act_offset, new_bank_offset, old_bank_offset; - s32 ret_val; - u16 data; - - ret_val = e1000e_update_nvm_checksum_generic(hw); - if (ret_val) - return ret_val;; - - if (nvm->type != e1000_nvm_flash_sw) - return ret_val;; - - ret_val = e1000_acquire_swflag_ich8lan(hw); - if (ret_val) - return ret_val;; - - /* We're writing to the opposite bank so if we're on bank 1, - * write to bank 0 etc. We also need to erase the segment that - * is going to be written */ - if (!(er32(EECD) & E1000_EECD_SEC1VAL)) { - new_bank_offset = nvm->flash_bank_size; - old_bank_offset = 0; - e1000_erase_flash_bank_ich8lan(hw, 1); - } else { - old_bank_offset = nvm->flash_bank_size; - new_bank_offset = 0; - e1000_erase_flash_bank_ich8lan(hw, 0); - } - - for (i = 0; i < E1000_ICH8_SHADOW_RAM_WORDS; i++) { - /* Determine whether to write the value stored - * in the other NVM bank or a modified value stored - * in the shadow RAM */ - if (dev_spec->shadow_ram[i].modified) { - data = dev_spec->shadow_ram[i].value; - } else { - e1000_read_flash_word_ich8lan(hw, - i + old_bank_offset, - &data); - } - - /* If the word is 0x13, then make sure the signature bits - * (15:14) are 11b until the commit has completed. - * This will allow us to write 10b which indicates the - * signature is valid. We want to do this after the write - * has completed so that we don't mark the segment valid - * while the write is still in progress */ - if (i == E1000_ICH_NVM_SIG_WORD) - data |= E1000_ICH_NVM_SIG_MASK; - - /* Convert offset to bytes. */ - act_offset = (i + new_bank_offset) << 1; - - udelay(100); - /* Write the bytes to the new bank. */ - ret_val = e1000_retry_write_flash_byte_ich8lan(hw, - act_offset, - (u8)data); - if (ret_val) - break; - - udelay(100); - ret_val = e1000_retry_write_flash_byte_ich8lan(hw, - act_offset + 1, - (u8)(data >> 8)); - if (ret_val) - break; - } - - /* Don't bother writing the segment valid bits if sector - * programming failed. */ - if (ret_val) { - hw_dbg(hw, "Flash commit failed.\n"); - e1000_release_swflag_ich8lan(hw); - return ret_val; - } - - /* Finally validate the new segment by setting bit 15:14 - * to 10b in word 0x13 , this can be done without an - * erase as well since these bits are 11 to start with - * and we need to change bit 14 to 0b */ - act_offset = new_bank_offset + E1000_ICH_NVM_SIG_WORD; - e1000_read_flash_word_ich8lan(hw, act_offset, &data); - data &= 0xBFFF; - ret_val = e1000_retry_write_flash_byte_ich8lan(hw, - act_offset * 2 + 1, - (u8)(data >> 8)); - if (ret_val) { - e1000_release_swflag_ich8lan(hw); - return ret_val; - } - - /* And invalidate the previously valid segment by setting - * its signature word (0x13) high_byte to 0b. This can be - * done without an erase because flash erase sets all bits - * to 1's. We can write 1's to 0's without an erase */ - act_offset = (old_bank_offset + E1000_ICH_NVM_SIG_WORD) * 2 + 1; - ret_val = e1000_retry_write_flash_byte_ich8lan(hw, act_offset, 0); - if (ret_val) { - e1000_release_swflag_ich8lan(hw); - return ret_val; - } - - /* Great! Everything worked, we can now clear the cached entries. */ - for (i = 0; i < E1000_ICH8_SHADOW_RAM_WORDS; i++) { - dev_spec->shadow_ram[i].modified = 0; - dev_spec->shadow_ram[i].value = 0xFFFF; - } - - e1000_release_swflag_ich8lan(hw); - - /* Reload the EEPROM, or else modifications will not appear - * until after the next adapter reset. - */ - e1000e_reload_nvm(hw); - msleep(10); - - return ret_val; -} - -/** - * e1000_validate_nvm_checksum_ich8lan - Validate EEPROM checksum - * @hw: pointer to the HW structure - * - * Check to see if checksum needs to be fixed by reading bit 6 in word 0x19. - * If the bit is 0, that the EEPROM had been modified, but the checksum was not - * calculated, in which case we need to calculate the checksum and set bit 6. - **/ -static s32 e1000_validate_nvm_checksum_ich8lan(struct e1000_hw *hw) -{ - s32 ret_val; - u16 data; - - /* Read 0x19 and check bit 6. If this bit is 0, the checksum - * needs to be fixed. This bit is an indication that the NVM - * was prepared by OEM software and did not calculate the - * checksum...a likely scenario. - */ - ret_val = e1000_read_nvm(hw, 0x19, 1, &data); - if (ret_val) - return ret_val; - - if ((data & 0x40) == 0) { - data |= 0x40; - ret_val = e1000_write_nvm(hw, 0x19, 1, &data); - if (ret_val) - return ret_val; - ret_val = e1000e_update_nvm_checksum(hw); - if (ret_val) - return ret_val; - } - - return e1000e_validate_nvm_checksum_generic(hw); -} - -/** - * e1000_write_flash_data_ich8lan - Writes bytes to the NVM - * @hw: pointer to the HW structure - * @offset: The offset (in bytes) of the byte/word to read. - * @size: Size of data to read, 1=byte 2=word - * @data: The byte(s) to write to the NVM. - * - * Writes one/two bytes to the NVM using the flash access registers. - **/ -static s32 e1000_write_flash_data_ich8lan(struct e1000_hw *hw, u32 offset, - u8 size, u16 data) -{ - union ich8_hws_flash_status hsfsts; - union ich8_hws_flash_ctrl hsflctl; - u32 flash_linear_addr; - u32 flash_data = 0; - s32 ret_val; - u8 count = 0; - - if (size < 1 || size > 2 || data > size * 0xff || - offset > ICH_FLASH_LINEAR_ADDR_MASK) - return -E1000_ERR_NVM; - - flash_linear_addr = (ICH_FLASH_LINEAR_ADDR_MASK & offset) + - hw->nvm.flash_base_addr; - - do { - udelay(1); - /* Steps */ - ret_val = e1000_flash_cycle_init_ich8lan(hw); - if (ret_val) - break; - - hsflctl.regval = er16flash(ICH_FLASH_HSFCTL); - /* 0b/1b corresponds to 1 or 2 byte size, respectively. */ - hsflctl.hsf_ctrl.fldbcount = size -1; - hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_WRITE; - ew16flash(ICH_FLASH_HSFCTL, hsflctl.regval); - - ew32flash(ICH_FLASH_FADDR, flash_linear_addr); - - if (size == 1) - flash_data = (u32)data & 0x00FF; - else - flash_data = (u32)data; - - ew32flash(ICH_FLASH_FDATA0, flash_data); - - /* check if FCERR is set to 1 , if set to 1, clear it - * and try the whole sequence a few more times else done */ - ret_val = e1000_flash_cycle_ich8lan(hw, - ICH_FLASH_WRITE_COMMAND_TIMEOUT); - if (!ret_val) - break; - - /* If we're here, then things are most likely - * completely hosed, but if the error condition - * is detected, it won't hurt to give it another - * try...ICH_FLASH_CYCLE_REPEAT_COUNT times. - */ - hsfsts.regval = er16flash(ICH_FLASH_HSFSTS); - if (hsfsts.hsf_status.flcerr == 1) - /* Repeat for some time before giving up. */ - continue; - if (hsfsts.hsf_status.flcdone == 0) { - hw_dbg(hw, "Timeout error - flash cycle " - "did not complete."); - break; - } - } while (count++ < ICH_FLASH_CYCLE_REPEAT_COUNT); - - return ret_val; -} - -/** - * e1000_write_flash_byte_ich8lan - Write a single byte to NVM - * @hw: pointer to the HW structure - * @offset: The index of the byte to read. - * @data: The byte to write to the NVM. - * - * Writes a single byte to the NVM using the flash access registers. - **/ -static s32 e1000_write_flash_byte_ich8lan(struct e1000_hw *hw, u32 offset, - u8 data) -{ - u16 word = (u16)data; - - return e1000_write_flash_data_ich8lan(hw, offset, 1, word); -} - -/** - * e1000_retry_write_flash_byte_ich8lan - Writes a single byte to NVM - * @hw: pointer to the HW structure - * @offset: The offset of the byte to write. - * @byte: The byte to write to the NVM. - * - * Writes a single byte to the NVM using the flash access registers. - * Goes through a retry algorithm before giving up. - **/ -static s32 e1000_retry_write_flash_byte_ich8lan(struct e1000_hw *hw, - u32 offset, u8 byte) -{ - s32 ret_val; - u16 program_retries; - - ret_val = e1000_write_flash_byte_ich8lan(hw, offset, byte); - if (!ret_val) - return ret_val; - - for (program_retries = 0; program_retries < 100; program_retries++) { - hw_dbg(hw, "Retrying Byte %2.2X at offset %u\n", byte, offset); - udelay(100); - ret_val = e1000_write_flash_byte_ich8lan(hw, offset, byte); - if (!ret_val) - break; - } - if (program_retries == 100) - return -E1000_ERR_NVM; - - return 0; -} - -/** - * e1000_erase_flash_bank_ich8lan - Erase a bank (4k) from NVM - * @hw: pointer to the HW structure - * @bank: 0 for first bank, 1 for second bank, etc. - * - * Erases the bank specified. Each bank is a 4k block. Banks are 0 based. - * bank N is 4096 * N + flash_reg_addr. - **/ -static s32 e1000_erase_flash_bank_ich8lan(struct e1000_hw *hw, u32 bank) -{ - struct e1000_nvm_info *nvm = &hw->nvm; - union ich8_hws_flash_status hsfsts; - union ich8_hws_flash_ctrl hsflctl; - u32 flash_linear_addr; - /* bank size is in 16bit words - adjust to bytes */ - u32 flash_bank_size = nvm->flash_bank_size * 2; - s32 ret_val; - s32 count = 0; - s32 iteration; - s32 sector_size; - s32 j; - - hsfsts.regval = er16flash(ICH_FLASH_HSFSTS); - - /* Determine HW Sector size: Read BERASE bits of hw flash status - * register */ - /* 00: The Hw sector is 256 bytes, hence we need to erase 16 - * consecutive sectors. The start index for the nth Hw sector - * can be calculated as = bank * 4096 + n * 256 - * 01: The Hw sector is 4K bytes, hence we need to erase 1 sector. - * The start index for the nth Hw sector can be calculated - * as = bank * 4096 - * 10: The Hw sector is 8K bytes, nth sector = bank * 8192 - * (ich9 only, otherwise error condition) - * 11: The Hw sector is 64K bytes, nth sector = bank * 65536 - */ - switch (hsfsts.hsf_status.berasesz) { - case 0: - /* Hw sector size 256 */ - sector_size = ICH_FLASH_SEG_SIZE_256; - iteration = flash_bank_size / ICH_FLASH_SEG_SIZE_256; - break; - case 1: - sector_size = ICH_FLASH_SEG_SIZE_4K; - iteration = flash_bank_size / ICH_FLASH_SEG_SIZE_4K; - break; - case 2: - if (hw->mac.type == e1000_ich9lan) { - sector_size = ICH_FLASH_SEG_SIZE_8K; - iteration = flash_bank_size / ICH_FLASH_SEG_SIZE_8K; - } else { - return -E1000_ERR_NVM; - } - break; - case 3: - sector_size = ICH_FLASH_SEG_SIZE_64K; - iteration = flash_bank_size / ICH_FLASH_SEG_SIZE_64K; - break; - default: - return -E1000_ERR_NVM; - } - - /* Start with the base address, then add the sector offset. */ - flash_linear_addr = hw->nvm.flash_base_addr; - flash_linear_addr += (bank) ? (sector_size * iteration) : 0; - - for (j = 0; j < iteration ; j++) { - do { - /* Steps */ - ret_val = e1000_flash_cycle_init_ich8lan(hw); - if (ret_val) - return ret_val; - - /* Write a value 11 (block Erase) in Flash - * Cycle field in hw flash control */ - hsflctl.regval = er16flash(ICH_FLASH_HSFCTL); - hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_ERASE; - ew16flash(ICH_FLASH_HSFCTL, hsflctl.regval); - - /* Write the last 24 bits of an index within the - * block into Flash Linear address field in Flash - * Address. - */ - flash_linear_addr += (j * sector_size); - ew32flash(ICH_FLASH_FADDR, flash_linear_addr); - - ret_val = e1000_flash_cycle_ich8lan(hw, - ICH_FLASH_ERASE_COMMAND_TIMEOUT); - if (ret_val == 0) - break; - - /* Check if FCERR is set to 1. If 1, - * clear it and try the whole sequence - * a few more times else Done */ - hsfsts.regval = er16flash(ICH_FLASH_HSFSTS); - if (hsfsts.hsf_status.flcerr == 1) - /* repeat for some time before - * giving up */ - continue; - else if (hsfsts.hsf_status.flcdone == 0) - return ret_val; - } while (++count < ICH_FLASH_CYCLE_REPEAT_COUNT); - } - - return 0; -} - -/** - * e1000_valid_led_default_ich8lan - Set the default LED settings - * @hw: pointer to the HW structure - * @data: Pointer to the LED settings - * - * Reads the LED default settings from the NVM to data. If the NVM LED - * settings is all 0's or F's, set the LED default to a valid LED default - * setting. - **/ -static s32 e1000_valid_led_default_ich8lan(struct e1000_hw *hw, u16 *data) -{ - s32 ret_val; - - ret_val = e1000_read_nvm(hw, NVM_ID_LED_SETTINGS, 1, data); - if (ret_val) { - hw_dbg(hw, "NVM Read Error\n"); - return ret_val; - } - - if (*data == ID_LED_RESERVED_0000 || - *data == ID_LED_RESERVED_FFFF) - *data = ID_LED_DEFAULT_ICH8LAN; - - return 0; -} - -/** - * e1000_get_bus_info_ich8lan - Get/Set the bus type and width - * @hw: pointer to the HW structure - * - * ICH8 use the PCI Express bus, but does not contain a PCI Express Capability - * register, so the the bus width is hard coded. - **/ -static s32 e1000_get_bus_info_ich8lan(struct e1000_hw *hw) -{ - struct e1000_bus_info *bus = &hw->bus; - s32 ret_val; - - ret_val = e1000e_get_bus_info_pcie(hw); - - /* ICH devices are "PCI Express"-ish. They have - * a configuration space, but do not contain - * PCI Express Capability registers, so bus width - * must be hardcoded. - */ - if (bus->width == e1000_bus_width_unknown) - bus->width = e1000_bus_width_pcie_x1; - - return ret_val; -} - -/** - * e1000_reset_hw_ich8lan - Reset the hardware - * @hw: pointer to the HW structure - * - * Does a full reset of the hardware which includes a reset of the PHY and - * MAC. - **/ -static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw) -{ - u32 ctrl, icr, kab; - s32 ret_val; - - /* Prevent the PCI-E bus from sticking if there is no TLP connection - * on the last TLP read/write transaction when MAC is reset. - */ - ret_val = e1000e_disable_pcie_master(hw); - if (ret_val) { - hw_dbg(hw, "PCI-E Master disable polling has failed.\n"); - } - - hw_dbg(hw, "Masking off all interrupts\n"); - ew32(IMC, 0xffffffff); - - /* Disable the Transmit and Receive units. Then delay to allow - * any pending transactions to complete before we hit the MAC - * with the global reset. - */ - ew32(RCTL, 0); - ew32(TCTL, E1000_TCTL_PSP); - e1e_flush(); - - msleep(10); - - /* Workaround for ICH8 bit corruption issue in FIFO memory */ - if (hw->mac.type == e1000_ich8lan) { - /* Set Tx and Rx buffer allocation to 8k apiece. */ - ew32(PBA, E1000_PBA_8K); - /* Set Packet Buffer Size to 16k. */ - ew32(PBS, E1000_PBS_16K); - } - - ctrl = er32(CTRL); - - if (!e1000_check_reset_block(hw)) { - /* PHY HW reset requires MAC CORE reset at the same - * time to make sure the interface between MAC and the - * external PHY is reset. - */ - ctrl |= E1000_CTRL_PHY_RST; - } - ret_val = e1000_acquire_swflag_ich8lan(hw); - hw_dbg(hw, "Issuing a global reset to ich8lan"); - ew32(CTRL, (ctrl | E1000_CTRL_RST)); - msleep(20); - - ret_val = e1000e_get_auto_rd_done(hw); - if (ret_val) { - /* - * When auto config read does not complete, do not - * return with an error. This can happen in situations - * where there is no eeprom and prevents getting link. - */ - hw_dbg(hw, "Auto Read Done did not complete\n"); - } - - ew32(IMC, 0xffffffff); - icr = er32(ICR); - - kab = er32(KABGTXD); - kab |= E1000_KABGTXD_BGSQLBIAS; - ew32(KABGTXD, kab); - - return ret_val; -} - -/** - * e1000_init_hw_ich8lan - Initialize the hardware - * @hw: pointer to the HW structure - * - * Prepares the hardware for transmit and receive by doing the following: - * - initialize hardware bits - * - initialize LED identification - * - setup receive address registers - * - setup flow control - * - setup transmit descriptors - * - clear statistics - **/ -static s32 e1000_init_hw_ich8lan(struct e1000_hw *hw) -{ - struct e1000_mac_info *mac = &hw->mac; - u32 ctrl_ext, txdctl, snoop; - s32 ret_val; - u16 i; - - e1000_initialize_hw_bits_ich8lan(hw); - - /* Initialize identification LED */ - ret_val = e1000e_id_led_init(hw); - if (ret_val) { - hw_dbg(hw, "Error initializing identification LED\n"); - return ret_val; - } - - /* Setup the receive address. */ - e1000e_init_rx_addrs(hw, mac->rar_entry_count); - - /* Zero out the Multicast HASH table */ - hw_dbg(hw, "Zeroing the MTA\n"); - for (i = 0; i < mac->mta_reg_count; i++) - E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0); - - /* Setup link and flow control */ - ret_val = e1000_setup_link_ich8lan(hw); - - /* Set the transmit descriptor write-back policy for both queues */ - txdctl = er32(TXDCTL); - txdctl = (txdctl & ~E1000_TXDCTL_WTHRESH) | - E1000_TXDCTL_FULL_TX_DESC_WB; - txdctl = (txdctl & ~E1000_TXDCTL_PTHRESH) | - E1000_TXDCTL_MAX_TX_DESC_PREFETCH; - ew32(TXDCTL, txdctl); - txdctl = er32(TXDCTL1); - txdctl = (txdctl & ~E1000_TXDCTL_WTHRESH) | - E1000_TXDCTL_FULL_TX_DESC_WB; - txdctl = (txdctl & ~E1000_TXDCTL_PTHRESH) | - E1000_TXDCTL_MAX_TX_DESC_PREFETCH; - ew32(TXDCTL1, txdctl); - - /* ICH8 has opposite polarity of no_snoop bits. - * By default, we should use snoop behavior. */ - if (mac->type == e1000_ich8lan) - snoop = PCIE_ICH8_SNOOP_ALL; - else - snoop = (u32) ~(PCIE_NO_SNOOP_ALL); - e1000e_set_pcie_no_snoop(hw, snoop); - - ctrl_ext = er32(CTRL_EXT); - ctrl_ext |= E1000_CTRL_EXT_RO_DIS; - ew32(CTRL_EXT, ctrl_ext); - - /* Clear all of the statistics registers (clear on read). It is - * important that we do this after we have tried to establish link - * because the symbol error count will increment wildly if there - * is no link. - */ - e1000_clear_hw_cntrs_ich8lan(hw); - - return 0; -} -/** - * e1000_initialize_hw_bits_ich8lan - Initialize required hardware bits - * @hw: pointer to the HW structure - * - * Sets/Clears required hardware bits necessary for correctly setting up the - * hardware for transmit and receive. - **/ -static void e1000_initialize_hw_bits_ich8lan(struct e1000_hw *hw) -{ - u32 reg; - - /* Extended Device Control */ - reg = er32(CTRL_EXT); - reg |= (1 << 22); - ew32(CTRL_EXT, reg); - - /* Transmit Descriptor Control 0 */ - reg = er32(TXDCTL); - reg |= (1 << 22); - ew32(TXDCTL, reg); - - /* Transmit Descriptor Control 1 */ - reg = er32(TXDCTL1); - reg |= (1 << 22); - ew32(TXDCTL1, reg); - - /* Transmit Arbitration Control 0 */ - reg = er32(TARC0); - if (hw->mac.type == e1000_ich8lan) - reg |= (1 << 28) | (1 << 29); - reg |= (1 << 23) | (1 << 24) | (1 << 26) | (1 << 27); - ew32(TARC0, reg); - - /* Transmit Arbitration Control 1 */ - reg = er32(TARC1); - if (er32(TCTL) & E1000_TCTL_MULR) - reg &= ~(1 << 28); - else - reg |= (1 << 28); - reg |= (1 << 24) | (1 << 26) | (1 << 30); - ew32(TARC1, reg); - - /* Device Status */ - if (hw->mac.type == e1000_ich8lan) { - reg = er32(STATUS); - reg &= ~(1 << 31); - ew32(STATUS, reg); - } -} - -/** - * e1000_setup_link_ich8lan - Setup flow control and link settings - * @hw: pointer to the HW structure - * - * Determines which flow control settings to use, then configures flow - * control. Calls the appropriate media-specific link configuration - * function. Assuming the adapter has a valid link partner, a valid link - * should be established. Assumes the hardware has previously been reset - * and the transmitter and receiver are not enabled. - **/ -static s32 e1000_setup_link_ich8lan(struct e1000_hw *hw) -{ - struct e1000_mac_info *mac = &hw->mac; - s32 ret_val; - - if (e1000_check_reset_block(hw)) - return 0; - - /* ICH parts do not have a word in the NVM to determine - * the default flow control setting, so we explicitly - * set it to full. - */ - if (mac->fc == e1000_fc_default) - mac->fc = e1000_fc_full; - - mac->original_fc = mac->fc; - - hw_dbg(hw, "After fix-ups FlowControl is now = %x\n", mac->fc); - - /* Continue to configure the copper link. */ - ret_val = e1000_setup_copper_link_ich8lan(hw); - if (ret_val) - return ret_val; - - ew32(FCTTV, mac->fc_pause_time); - - return e1000e_set_fc_watermarks(hw); -} - -/** - * e1000_setup_copper_link_ich8lan - Configure MAC/PHY interface - * @hw: pointer to the HW structure - * - * Configures the kumeran interface to the PHY to wait the appropriate time - * when polling the PHY, then call the generic setup_copper_link to finish - * configuring the copper link. - **/ -static s32 e1000_setup_copper_link_ich8lan(struct e1000_hw *hw) -{ - u32 ctrl; - s32 ret_val; - u16 reg_data; - - ctrl = er32(CTRL); - ctrl |= E1000_CTRL_SLU; - ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); - ew32(CTRL, ctrl); - - /* Set the mac to wait the maximum time between each iteration - * and increase the max iterations when polling the phy; - * this fixes erroneous timeouts at 10Mbps. */ - ret_val = e1000e_write_kmrn_reg(hw, GG82563_REG(0x34, 4), 0xFFFF); - if (ret_val) - return ret_val; - ret_val = e1000e_read_kmrn_reg(hw, GG82563_REG(0x34, 9), ®_data); - if (ret_val) - return ret_val; - reg_data |= 0x3F; - ret_val = e1000e_write_kmrn_reg(hw, GG82563_REG(0x34, 9), reg_data); - if (ret_val) - return ret_val; - - if (hw->phy.type == e1000_phy_igp_3) { - ret_val = e1000e_copper_link_setup_igp(hw); - if (ret_val) - return ret_val; - } - - return e1000e_setup_copper_link(hw); -} - -/** - * e1000_get_link_up_info_ich8lan - Get current link speed and duplex - * @hw: pointer to the HW structure - * @speed: pointer to store current link speed - * @duplex: pointer to store the current link duplex - * - * Calls the generic get_speed_and_duplex to retreive the current link - * information and then calls the Kumeran lock loss workaround for links at - * gigabit speeds. - **/ -static s32 e1000_get_link_up_info_ich8lan(struct e1000_hw *hw, u16 *speed, - u16 *duplex) -{ - s32 ret_val; - - ret_val = e1000e_get_speed_and_duplex_copper(hw, speed, duplex); - if (ret_val) - return ret_val; - - if ((hw->mac.type == e1000_ich8lan) && - (hw->phy.type == e1000_phy_igp_3) && - (*speed == SPEED_1000)) { - ret_val = e1000_kmrn_lock_loss_workaround_ich8lan(hw); - } - - return ret_val; -} - -/** - * e1000_kmrn_lock_loss_workaround_ich8lan - Kumeran workaround - * @hw: pointer to the HW structure - * - * Work-around for 82566 Kumeran PCS lock loss: - * On link status change (i.e. PCI reset, speed change) and link is up and - * speed is gigabit- - * 0) if workaround is optionally disabled do nothing - * 1) wait 1ms for Kumeran link to come up - * 2) check Kumeran Diagnostic register PCS lock loss bit - * 3) if not set the link is locked (all is good), otherwise... - * 4) reset the PHY - * 5) repeat up to 10 times - * Note: this is only called for IGP3 copper when speed is 1gb. - **/ -static s32 e1000_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw) -{ - struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; - u32 phy_ctrl; - s32 ret_val; - u16 i, data; - bool link; - - if (!dev_spec->kmrn_lock_loss_workaround_enabled) - return 0; - - /* Make sure link is up before proceeding. If not just return. - * Attempting this while link is negotiating fouled up link - * stability */ - ret_val = e1000e_phy_has_link_generic(hw, 1, 0, &link); - if (!link) - return 0; - - for (i = 0; i < 10; i++) { - /* read once to clear */ - ret_val = e1e_rphy(hw, IGP3_KMRN_DIAG, &data); - if (ret_val) - return ret_val; - /* and again to get new status */ - ret_val = e1e_rphy(hw, IGP3_KMRN_DIAG, &data); - if (ret_val) - return ret_val; - - /* check for PCS lock */ - if (!(data & IGP3_KMRN_DIAG_PCS_LOCK_LOSS)) - return 0; - - /* Issue PHY reset */ - e1000_phy_hw_reset(hw); - mdelay(5); - } - /* Disable GigE link negotiation */ - phy_ctrl = er32(PHY_CTRL); - phy_ctrl |= (E1000_PHY_CTRL_GBE_DISABLE | - E1000_PHY_CTRL_NOND0A_GBE_DISABLE); - ew32(PHY_CTRL, phy_ctrl); - - /* Call gig speed drop workaround on Gig disable before accessing - * any PHY registers */ - e1000e_gig_downshift_workaround_ich8lan(hw); - - /* unable to acquire PCS lock */ - return -E1000_ERR_PHY; -} - -/** - * e1000_set_kmrn_lock_loss_workaound_ich8lan - Set Kumeran workaround state - * @hw: pointer to the HW structure - * @state: boolean value used to set the current Kumeran workaround state - * - * If ICH8, set the current Kumeran workaround state (enabled - TRUE - * /disabled - FALSE). - **/ -void e1000e_set_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw, - bool state) -{ - struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; - - if (hw->mac.type != e1000_ich8lan) { - hw_dbg(hw, "Workaround applies to ICH8 only.\n"); - return; - } - - dev_spec->kmrn_lock_loss_workaround_enabled = state; -} - -/** - * e1000_ipg3_phy_powerdown_workaround_ich8lan - Power down workaround on D3 - * @hw: pointer to the HW structure - * - * Workaround for 82566 power-down on D3 entry: - * 1) disable gigabit link - * 2) write VR power-down enable - * 3) read it back - * Continue if successful, else issue LCD reset and repeat - **/ -void e1000e_igp3_phy_powerdown_workaround_ich8lan(struct e1000_hw *hw) -{ - u32 reg; - u16 data; - u8 retry = 0; - - if (hw->phy.type != e1000_phy_igp_3) - return; - - /* Try the workaround twice (if needed) */ - do { - /* Disable link */ - reg = er32(PHY_CTRL); - reg |= (E1000_PHY_CTRL_GBE_DISABLE | - E1000_PHY_CTRL_NOND0A_GBE_DISABLE); - ew32(PHY_CTRL, reg); - - /* Call gig speed drop workaround on Gig disable before - * accessing any PHY registers */ - if (hw->mac.type == e1000_ich8lan) - e1000e_gig_downshift_workaround_ich8lan(hw); - - /* Write VR power-down enable */ - e1e_rphy(hw, IGP3_VR_CTRL, &data); - data &= ~IGP3_VR_CTRL_DEV_POWERDOWN_MODE_MASK; - e1e_wphy(hw, IGP3_VR_CTRL, data | IGP3_VR_CTRL_MODE_SHUTDOWN); - - /* Read it back and test */ - e1e_rphy(hw, IGP3_VR_CTRL, &data); - data &= IGP3_VR_CTRL_DEV_POWERDOWN_MODE_MASK; - if ((data == IGP3_VR_CTRL_MODE_SHUTDOWN) || retry) - break; - - /* Issue PHY reset and repeat at most one more time */ - reg = er32(CTRL); - ew32(CTRL, reg | E1000_CTRL_PHY_RST); - retry++; - } while (retry); -} - -/** - * e1000e_gig_downshift_workaround_ich8lan - WoL from S5 stops working - * @hw: pointer to the HW structure - * - * Steps to take when dropping from 1Gb/s (eg. link cable removal (LSC), - * LPLU, Gig disable, MDIC PHY reset): - * 1) Set Kumeran Near-end loopback - * 2) Clear Kumeran Near-end loopback - * Should only be called for ICH8[m] devices with IGP_3 Phy. - **/ -void e1000e_gig_downshift_workaround_ich8lan(struct e1000_hw *hw) -{ - s32 ret_val; - u16 reg_data; - - if ((hw->mac.type != e1000_ich8lan) || - (hw->phy.type != e1000_phy_igp_3)) - return; - - ret_val = e1000e_read_kmrn_reg(hw, E1000_KMRNCTRLSTA_DIAG_OFFSET, - ®_data); - if (ret_val) - return; - reg_data |= E1000_KMRNCTRLSTA_DIAG_NELPBK; - ret_val = e1000e_write_kmrn_reg(hw, E1000_KMRNCTRLSTA_DIAG_OFFSET, - reg_data); - if (ret_val) - return; - reg_data &= ~E1000_KMRNCTRLSTA_DIAG_NELPBK; - ret_val = e1000e_write_kmrn_reg(hw, E1000_KMRNCTRLSTA_DIAG_OFFSET, - reg_data); -} - -/** - * e1000_cleanup_led_ich8lan - Restore the default LED operation - * @hw: pointer to the HW structure - * - * Return the LED back to the default configuration. - **/ -static s32 e1000_cleanup_led_ich8lan(struct e1000_hw *hw) -{ - if (hw->phy.type == e1000_phy_ife) - return e1e_wphy(hw, IFE_PHY_SPECIAL_CONTROL_LED, 0); - - ew32(LEDCTL, hw->mac.ledctl_default); - return 0; -} - -/** - * e1000_led_on_ich8lan - Turn LEDs on - * @hw: pointer to the HW structure - * - * Turn on the LEDs. - **/ -static s32 e1000_led_on_ich8lan(struct e1000_hw *hw) -{ - if (hw->phy.type == e1000_phy_ife) - return e1e_wphy(hw, IFE_PHY_SPECIAL_CONTROL_LED, - (IFE_PSCL_PROBE_MODE | IFE_PSCL_PROBE_LEDS_ON)); - - ew32(LEDCTL, hw->mac.ledctl_mode2); - return 0; -} - -/** - * e1000_led_off_ich8lan - Turn LEDs off - * @hw: pointer to the HW structure - * - * Turn off the LEDs. - **/ -static s32 e1000_led_off_ich8lan(struct e1000_hw *hw) -{ - if (hw->phy.type == e1000_phy_ife) - return e1e_wphy(hw, IFE_PHY_SPECIAL_CONTROL_LED, - (IFE_PSCL_PROBE_MODE | IFE_PSCL_PROBE_LEDS_OFF)); - - ew32(LEDCTL, hw->mac.ledctl_mode1); - return 0; -} - -/** - * e1000_clear_hw_cntrs_ich8lan - Clear statistical counters - * @hw: pointer to the HW structure - * - * Clears hardware counters specific to the silicon family and calls - * clear_hw_cntrs_generic to clear all general purpose counters. - **/ -static void e1000_clear_hw_cntrs_ich8lan(struct e1000_hw *hw) -{ - u32 temp; - - e1000e_clear_hw_cntrs_base(hw); - - temp = er32(ALGNERRC); - temp = er32(RXERRC); - temp = er32(TNCRS); - temp = er32(CEXTERR); - temp = er32(TSCTC); - temp = er32(TSCTFC); - - temp = er32(MGTPRC); - temp = er32(MGTPDC); - temp = er32(MGTPTC); - - temp = er32(IAC); - temp = er32(ICRXOC); - -} - -static struct e1000_mac_operations ich8_mac_ops = { - .mng_mode_enab = E1000_ICH_MNG_IAMT_MODE << E1000_FWSM_MODE_SHIFT, - .check_for_link = e1000e_check_for_copper_link, - .cleanup_led = e1000_cleanup_led_ich8lan, - .clear_hw_cntrs = e1000_clear_hw_cntrs_ich8lan, - .get_bus_info = e1000_get_bus_info_ich8lan, - .get_link_up_info = e1000_get_link_up_info_ich8lan, - .led_on = e1000_led_on_ich8lan, - .led_off = e1000_led_off_ich8lan, - .mc_addr_list_update = e1000e_mc_addr_list_update_generic, - .reset_hw = e1000_reset_hw_ich8lan, - .init_hw = e1000_init_hw_ich8lan, - .setup_link = e1000_setup_link_ich8lan, - .setup_physical_interface= e1000_setup_copper_link_ich8lan, -}; - -static struct e1000_phy_operations ich8_phy_ops = { - .acquire_phy = e1000_acquire_swflag_ich8lan, - .check_reset_block = e1000_check_reset_block_ich8lan, - .commit_phy = NULL, - .force_speed_duplex = e1000_phy_force_speed_duplex_ich8lan, - .get_cfg_done = e1000e_get_cfg_done, - .get_cable_length = e1000e_get_cable_length_igp_2, - .get_phy_info = e1000_get_phy_info_ich8lan, - .read_phy_reg = e1000e_read_phy_reg_igp, - .release_phy = e1000_release_swflag_ich8lan, - .reset_phy = e1000_phy_hw_reset_ich8lan, - .set_d0_lplu_state = e1000_set_d0_lplu_state_ich8lan, - .set_d3_lplu_state = e1000_set_d3_lplu_state_ich8lan, - .write_phy_reg = e1000e_write_phy_reg_igp, -}; - -static struct e1000_nvm_operations ich8_nvm_ops = { - .acquire_nvm = e1000_acquire_swflag_ich8lan, - .read_nvm = e1000_read_nvm_ich8lan, - .release_nvm = e1000_release_swflag_ich8lan, - .update_nvm = e1000_update_nvm_checksum_ich8lan, - .valid_led_default = e1000_valid_led_default_ich8lan, - .validate_nvm = e1000_validate_nvm_checksum_ich8lan, - .write_nvm = e1000_write_nvm_ich8lan, -}; - -struct e1000_info e1000_ich8_info = { - .mac = e1000_ich8lan, - .flags = FLAG_HAS_WOL - | FLAG_RX_CSUM_ENABLED - | FLAG_HAS_CTRLEXT_ON_LOAD - | FLAG_HAS_AMT - | FLAG_HAS_FLASH - | FLAG_APME_IN_WUC, - .pba = 8, - .get_invariants = e1000_get_invariants_ich8lan, - .mac_ops = &ich8_mac_ops, - .phy_ops = &ich8_phy_ops, - .nvm_ops = &ich8_nvm_ops, -}; - -struct e1000_info e1000_ich9_info = { - .mac = e1000_ich9lan, - .flags = FLAG_HAS_JUMBO_FRAMES - | FLAG_HAS_WOL - | FLAG_RX_CSUM_ENABLED - | FLAG_HAS_CTRLEXT_ON_LOAD - | FLAG_HAS_AMT - | FLAG_HAS_ERT - | FLAG_HAS_FLASH - | FLAG_APME_IN_WUC, - .pba = 10, - .get_invariants = e1000_get_invariants_ich8lan, - .mac_ops = &ich8_mac_ops, - .phy_ops = &ich8_phy_ops, - .nvm_ops = &ich8_nvm_ops, -}; - |