1 files changed, 0 insertions, 116 deletions
diff --git a/arch/arm/mach-u300/spi.c b/arch/arm/mach-u300/spi.c
deleted file mode 100644
index 00869def542..00000000000
--- a/arch/arm/mach-u300/spi.c
+++ /dev/null
@@ -1,116 +0,0 @@
-/*
- * arch/arm/mach-u300/spi.c
- *
- * Copyright (C) 2009 ST-Ericsson AB
- * License terms: GNU General Public License (GPL) version 2
- *
- * Author: Linus Walleij <linus.walleij@stericsson.com>
- */
-#include <linux/device.h>
-#include <linux/amba/bus.h>
-#include <linux/spi/spi.h>
-#include <linux/amba/pl022.h>
-#include <linux/err.h>
-#include "padmux.h"
-
-/*
- * The following is for the actual devices on the SSP/SPI bus
- */
-#ifdef CONFIG_MACH_U300_SPIDUMMY
-static void select_dummy_chip(u32 chipselect)
-{
-	pr_debug("CORE: %s called with CS=0x%x (%s)\n",
-		 __func__,
-		 chipselect,
-		 chipselect ? "unselect chip" : "select chip");
-	/*
-	 * Here you would write the chip select value to the GPIO pins if
-	 * this was a real chip (but this is a loopback dummy).
-	 */
-}
-
-struct pl022_config_chip dummy_chip_info = {
-	/*
-	 * available POLLING_TRANSFER and INTERRUPT_TRANSFER,
-	 * DMA_TRANSFER does not work
-	 */
-	.com_mode = INTERRUPT_TRANSFER,
-	.iface = SSP_INTERFACE_MOTOROLA_SPI,
-	/* We can only act as master but SSP_SLAVE is possible in theory */
-	.hierarchy = SSP_MASTER,
-	/* 0 = drive TX even as slave, 1 = do not drive TX as slave */
-	.slave_tx_disable = 0,
-	.rx_lev_trig = SSP_RX_1_OR_MORE_ELEM,
-	.tx_lev_trig = SSP_TX_1_OR_MORE_EMPTY_LOC,
-	.ctrl_len = SSP_BITS_12,
-	.wait_state = SSP_MWIRE_WAIT_ZERO,
-	.duplex = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX,
-	/*
-	 * This is where you insert a call to a function to enable CS
-	 * (usually GPIO) for a certain chip.
-	 */
-	.cs_control = select_dummy_chip,
-};
-#endif
-
-static struct spi_board_info u300_spi_devices[] = {
-#ifdef CONFIG_MACH_U300_SPIDUMMY
-	{
-		/* A dummy chip used for loopback tests */
-		.modalias       = "spi-dummy",
-		/* Really dummy, pass in additional chip config here */
-		.platform_data  = NULL,
-		/* This defines how the controller shall handle the device */
-		.controller_data = &dummy_chip_info,
-		/* .irq - no external IRQ routed from this device */
-		.max_speed_hz   = 1000000,
-		.bus_num        = 0, /* Only one bus on this chip */
-		.chip_select    = 0,
-		/* Means SPI_CS_HIGH, change if e.g low CS */
-		.mode           = SPI_MODE_1 | SPI_LOOP,
-	},
-#endif
-};
-
-static struct pl022_ssp_controller ssp_platform_data = {
-	/* If you have several SPI buses this varies, we have only bus 0 */
-	.bus_id = 0,
-	/* Set this to 1 when we think we got DMA working */
-	.enable_dma = 0,
-	/*
-	 * On the APP CPU GPIO 4, 5 and 6 are connected as generic
-	 * chip selects for SPI. (Same on U330, U335 and U365.)
-	 * TODO: make sure the GPIO driver can select these properly
-	 * and do padmuxing accordingly too.
-	 */
-	.num_chipselect = 3,
-};
-
-
-void __init u300_spi_init(struct amba_device *adev)
-{
-	struct pmx *pmx;
-
-	adev->dev.platform_data = &ssp_platform_data;
-	/*
-	 * Setup padmuxing for SPI. Since this must always be
-	 * compiled into the kernel, pmx is never released.
-	 */
-	pmx = pmx_get(&adev->dev, U300_APP_PMX_SPI_SETTING);
-
-	if (IS_ERR(pmx))
-		dev_warn(&adev->dev, "Could not get padmux handle\n");
-	else {
-		int ret;
-
-		ret = pmx_activate(&adev->dev, pmx);
-		if (IS_ERR_VALUE(ret))
-			dev_warn(&adev->dev, "Could not activate padmuxing\n");
-	}
-
-}
-void __init u300_spi_register_board_devices(void)
-{
-	/* Register any SPI devices */
-	spi_register_board_info(u300_spi_devices, ARRAY_SIZE(u300_spi_devices));
-}