diff options
Diffstat (limited to 'arch/arm/mach-davinci/board-da830-evm.c')
| -rw-r--r-- | arch/arm/mach-davinci/board-da830-evm.c | 227 |
1 files changed, 173 insertions, 54 deletions
diff --git a/arch/arm/mach-davinci/board-da830-evm.c b/arch/arm/mach-davinci/board-da830-evm.c index 31dc9901e55..5623131c4f0 100644 --- a/arch/arm/mach-davinci/board-da830-evm.c +++ b/arch/arm/mach-davinci/board-da830-evm.c @@ -17,25 +17,26 @@ #include <linux/platform_device.h> #include <linux/i2c.h> #include <linux/i2c/pcf857x.h> -#include <linux/i2c/at24.h> +#include <linux/platform_data/at24.h> #include <linux/mtd/mtd.h> #include <linux/mtd/partitions.h> +#include <linux/spi/spi.h> +#include <linux/spi/flash.h> +#include <linux/platform_data/gpio-davinci.h> +#include <linux/platform_data/mtd-davinci.h> +#include <linux/platform_data/mtd-davinci-aemif.h> +#include <linux/platform_data/spi-davinci.h> +#include <linux/platform_data/usb-davinci.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> +#include <mach/common.h> #include <mach/cp_intc.h> #include <mach/mux.h> -#include <mach/nand.h> #include <mach/da8xx.h> -#include <mach/usb.h> - -#define DA830_EVM_PHY_MASK 0x0 -#define DA830_EVM_MDIO_FREQUENCY 2200000 /* PHY bus frequency */ - -#define DA830_EMIF25_ASYNC_DATA_CE3_BASE 0x62000000 -#define DA830_EMIF25_CONTROL_BASE 0x68000000 +#define DA830_EVM_PHY_ID "" /* * USB1 VBUS is controlled by GPIO1[15], over-current is reported on GPIO2[4]. */ @@ -75,7 +76,7 @@ static int da830_evm_usb_ocic_notify(da8xx_ocic_handler_t handler) if (handler != NULL) { da830_evm_usb_ocic_handler = handler; - error = request_irq(irq, da830_evm_usb_ocic_irq, IRQF_DISABLED | + error = request_irq(irq, da830_evm_usb_ocic_irq, IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, "OHCI over-current indicator", NULL); if (error) @@ -112,7 +113,7 @@ static __init void da830_evm_usb_init(void) * Set up USB clock/mode in the CFGCHIP2 register. * FYI: CFGCHIP2 is 0x0000ef00 initially. */ - cfgchip2 = __raw_readl(DA8XX_SYSCFG_VIRT(DA8XX_CFGCHIP2_REG)); + cfgchip2 = __raw_readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG)); /* USB2.0 PHY reference clock is 24 MHz */ cfgchip2 &= ~CFGCHIP2_REFFREQ; @@ -139,7 +140,7 @@ static __init void da830_evm_usb_init(void) cfgchip2 |= CFGCHIP2_SESENDEN | CFGCHIP2_VBDTCTEN; #endif - __raw_writel(cfgchip2, DA8XX_SYSCFG_VIRT(DA8XX_CFGCHIP2_REG)); + __raw_writel(cfgchip2, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG)); /* USB_REFCLKIN is not used. */ ret = davinci_cfg_reg(DA830_USB0_DRVVBUS); @@ -157,7 +158,7 @@ static __init void da830_evm_usb_init(void) __func__, ret); } - ret = da8xx_pinmux_setup(da830_evm_usb11_pins); + ret = davinci_cfg_reg_list(da830_evm_usb11_pins); if (ret) { pr_warning("%s: USB 1.1 PinMux setup failed: %d\n", __func__, ret); @@ -186,10 +187,6 @@ static __init void da830_evm_usb_init(void) __func__, ret); } -static struct davinci_uart_config da830_evm_uart_config __initdata = { - .enabled_uarts = 0x7, -}; - static const short da830_evm_mcasp1_pins[] = { DA830_AHCLKX1, DA830_ACLKX1, DA830_AFSX1, DA830_AHCLKR1, DA830_AFSR1, DA830_AMUTE1, DA830_AXR1_0, DA830_AXR1_1, DA830_AXR1_2, DA830_AXR1_5, @@ -211,7 +208,7 @@ static struct snd_platform_data da830_evm_snd_data = { .num_serializer = ARRAY_SIZE(da830_iis_serializer_direction), .tdm_slots = 2, .serial_dir = da830_iis_serializer_direction, - .eventq_no = EVENTQ_0, + .asp_chan_q = EVENTQ_0, .version = MCASP_VERSION_2, .txnumevt = 1, .rxnumevt = 1, @@ -229,25 +226,31 @@ static const short da830_evm_mmc_sd_pins[] = { }; #define DA830_MMCSD_WP_PIN GPIO_TO_PIN(2, 1) +#define DA830_MMCSD_CD_PIN GPIO_TO_PIN(2, 2) static int da830_evm_mmc_get_ro(int index) { return gpio_get_value(DA830_MMCSD_WP_PIN); } +static int da830_evm_mmc_get_cd(int index) +{ + return !gpio_get_value(DA830_MMCSD_CD_PIN); +} + static struct davinci_mmc_config da830_evm_mmc_config = { .get_ro = da830_evm_mmc_get_ro, - .wires = 4, + .get_cd = da830_evm_mmc_get_cd, + .wires = 8, .max_freq = 50000000, .caps = MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED, - .version = MMC_CTLR_VERSION_2, }; static inline void da830_evm_init_mmc(void) { int ret; - ret = da8xx_pinmux_setup(da830_evm_mmc_sd_pins); + ret = davinci_cfg_reg_list(da830_evm_mmc_sd_pins); if (ret) { pr_warning("da830_evm_init: mmc/sd mux setup failed: %d\n", ret); @@ -262,6 +265,14 @@ static inline void da830_evm_init_mmc(void) } gpio_direction_input(DA830_MMCSD_WP_PIN); + ret = gpio_request(DA830_MMCSD_CD_PIN, "MMC CD\n"); + if (ret) { + pr_warning("da830_evm_init: can not open GPIO %d\n", + DA830_MMCSD_CD_PIN); + return; + } + gpio_direction_input(DA830_MMCSD_CD_PIN); + ret = da8xx_register_mmcsd0(&da830_evm_mmc_config); if (ret) { pr_warning("da830_evm_init: mmc/sd registration failed: %d\n", @@ -284,11 +295,7 @@ static const short da830_evm_emif25_pins[] = { -1 }; -#if defined(CONFIG_MMC_DAVINCI) || defined(CONFIG_MMC_DAVINCI_MODULE) -#define HAS_MMC 1 -#else -#define HAS_MMC 0 -#endif +#define HAS_MMC IS_ENABLED(CONFIG_MMC_DAVINCI) #ifdef CONFIG_DA830_UI_NAND static struct mtd_partition da830_evm_nand_partitions[] = { @@ -348,25 +355,36 @@ static struct nand_bbt_descr da830_evm_nand_bbt_mirror_descr = { .pattern = da830_evm_nand_mirror_pattern }; +static struct davinci_aemif_timing da830_evm_nandflash_timing = { + .wsetup = 24, + .wstrobe = 21, + .whold = 14, + .rsetup = 19, + .rstrobe = 50, + .rhold = 0, + .ta = 20, +}; + static struct davinci_nand_pdata da830_evm_nand_pdata = { .parts = da830_evm_nand_partitions, .nr_parts = ARRAY_SIZE(da830_evm_nand_partitions), .ecc_mode = NAND_ECC_HW, .ecc_bits = 4, - .options = NAND_USE_FLASH_BBT, + .bbt_options = NAND_BBT_USE_FLASH, .bbt_td = &da830_evm_nand_bbt_main_descr, .bbt_md = &da830_evm_nand_bbt_mirror_descr, + .timing = &da830_evm_nandflash_timing, }; static struct resource da830_evm_nand_resources[] = { [0] = { /* First memory resource is NAND I/O window */ - .start = DA830_EMIF25_ASYNC_DATA_CE3_BASE, - .end = DA830_EMIF25_ASYNC_DATA_CE3_BASE + PAGE_SIZE - 1, + .start = DA8XX_AEMIF_CS3_BASE, + .end = DA8XX_AEMIF_CS3_BASE + PAGE_SIZE - 1, .flags = IORESOURCE_MEM, }, [1] = { /* Second memory resource is AEMIF control registers */ - .start = DA830_EMIF25_CONTROL_BASE, - .end = DA830_EMIF25_CONTROL_BASE + SZ_32K - 1, + .start = DA8XX_AEMIF_CTL_BASE, + .end = DA8XX_AEMIF_CTL_BASE + SZ_32K - 1, .flags = IORESOURCE_MEM, }, }; @@ -392,7 +410,7 @@ static inline void da830_evm_init_nand(int mux_mode) return; } - ret = da8xx_pinmux_setup(da830_evm_emif25_pins); + ret = davinci_cfg_reg_list(da830_evm_emif25_pins); if (ret) pr_warning("da830_evm_init: emif25 mux setup failed: %d\n", ret); @@ -401,6 +419,9 @@ static inline void da830_evm_init_nand(int mux_mode) if (ret) pr_warning("da830_evm_init: NAND device not registered.\n"); + if (davinci_aemif_setup(&da830_evm_nand_device)) + pr_warn("%s: Cannot configure AEMIF.\n", __func__); + gpio_direction_output(mux_mode, 1); } #else @@ -412,7 +433,7 @@ static inline void da830_evm_init_lcdc(int mux_mode) { int ret; - ret = da8xx_pinmux_setup(da830_lcdcntl_pins); + ret = davinci_cfg_reg_list(da830_lcdcntl_pins); if (ret) pr_warning("da830_evm_init: lcdcntl mux setup failed: %d\n", ret); @@ -482,17 +503,109 @@ static struct davinci_i2c_platform_data da830_evm_i2c_0_pdata = { .bus_delay = 0, /* usec */ }; +/* + * The following EDMA channels/slots are not being used by drivers (for + * example: Timer, GPIO, UART events etc) on da830/omap-l137 EVM, hence + * they are being reserved for codecs on the DSP side. + */ +static const s16 da830_dma_rsv_chans[][2] = { + /* (offset, number) */ + { 8, 2}, + {12, 2}, + {24, 4}, + {30, 2}, + {-1, -1} +}; + +static const s16 da830_dma_rsv_slots[][2] = { + /* (offset, number) */ + { 8, 2}, + {12, 2}, + {24, 4}, + {30, 26}, + {-1, -1} +}; + +static struct edma_rsv_info da830_edma_rsv[] = { + { + .rsv_chans = da830_dma_rsv_chans, + .rsv_slots = da830_dma_rsv_slots, + }, +}; + +static struct mtd_partition da830evm_spiflash_part[] = { + [0] = { + .name = "DSP-UBL", + .offset = 0, + .size = SZ_8K, + .mask_flags = MTD_WRITEABLE, + }, + [1] = { + .name = "ARM-UBL", + .offset = MTDPART_OFS_APPEND, + .size = SZ_16K + SZ_8K, + .mask_flags = MTD_WRITEABLE, + }, + [2] = { + .name = "U-Boot", + .offset = MTDPART_OFS_APPEND, + .size = SZ_256K - SZ_32K, + .mask_flags = MTD_WRITEABLE, + }, + [3] = { + .name = "U-Boot-Environment", + .offset = MTDPART_OFS_APPEND, + .size = SZ_16K, + .mask_flags = 0, + }, + [4] = { + .name = "Kernel", + .offset = MTDPART_OFS_APPEND, + .size = MTDPART_SIZ_FULL, + .mask_flags = 0, + }, +}; + +static struct flash_platform_data da830evm_spiflash_data = { + .name = "m25p80", + .parts = da830evm_spiflash_part, + .nr_parts = ARRAY_SIZE(da830evm_spiflash_part), + .type = "w25x32", +}; + +static struct davinci_spi_config da830evm_spiflash_cfg = { + .io_type = SPI_IO_TYPE_DMA, + .c2tdelay = 8, + .t2cdelay = 8, +}; + +static struct spi_board_info da830evm_spi_info[] = { + { + .modalias = "m25p80", + .platform_data = &da830evm_spiflash_data, + .controller_data = &da830evm_spiflash_cfg, + .mode = SPI_MODE_0, + .max_speed_hz = 30000000, + .bus_num = 0, + .chip_select = 0, + }, +}; + static __init void da830_evm_init(void) { struct davinci_soc_info *soc_info = &davinci_soc_info; int ret; - ret = da8xx_register_edma(); + ret = da830_register_gpio(); + if (ret) + pr_warn("da830_evm_init: GPIO init failed: %d\n", ret); + + ret = da830_register_edma(da830_edma_rsv); if (ret) pr_warning("da830_evm_init: edma registration failed: %d\n", ret); - ret = da8xx_pinmux_setup(da830_i2c0_pins); + ret = davinci_cfg_reg_list(da830_i2c0_pins); if (ret) pr_warning("da830_evm_init: i2c0 mux setup failed: %d\n", ret); @@ -504,11 +617,10 @@ static __init void da830_evm_init(void) da830_evm_usb_init(); - soc_info->emac_pdata->phy_mask = DA830_EVM_PHY_MASK; - soc_info->emac_pdata->mdio_max_freq = DA830_EVM_MDIO_FREQUENCY; soc_info->emac_pdata->rmii_en = 1; + soc_info->emac_pdata->phy_id = DA830_EVM_PHY_ID; - ret = da8xx_pinmux_setup(da830_cpgmac_pins); + ret = davinci_cfg_reg_list(da830_cpgmac_pins); if (ret) pr_warning("da830_evm_init: cpgmac mux setup failed: %d\n", ret); @@ -523,11 +635,11 @@ static __init void da830_evm_init(void) pr_warning("da830_evm_init: watchdog registration failed: %d\n", ret); - davinci_serial_init(&da830_evm_uart_config); + davinci_serial_init(da8xx_serial_device); i2c_register_board_info(1, da830_evm_i2c_devices, ARRAY_SIZE(da830_evm_i2c_devices)); - ret = da8xx_pinmux_setup(da830_evm_mcasp1_pins); + ret = davinci_cfg_reg_list(da830_evm_mcasp1_pins); if (ret) pr_warning("da830_evm_init: mcasp1 mux setup failed: %d\n", ret); @@ -539,35 +651,42 @@ static __init void da830_evm_init(void) ret = da8xx_register_rtc(); if (ret) pr_warning("da830_evm_init: rtc setup failed: %d\n", ret); + + ret = spi_register_board_info(da830evm_spi_info, + ARRAY_SIZE(da830evm_spi_info)); + if (ret) + pr_warn("%s: spi info registration failed: %d\n", __func__, + ret); + + ret = da8xx_register_spi_bus(0, ARRAY_SIZE(da830evm_spi_info)); + if (ret) + pr_warning("da830_evm_init: spi 0 registration failed: %d\n", + ret); } #ifdef CONFIG_SERIAL_8250_CONSOLE static int __init da830_evm_console_init(void) { + if (!machine_is_davinci_da830_evm()) + return 0; + return add_preferred_console("ttyS", 2, "115200"); } console_initcall(da830_evm_console_init); #endif -static __init void da830_evm_irq_init(void) -{ - struct davinci_soc_info *soc_info = &davinci_soc_info; - - cp_intc_init((void __iomem *)DA8XX_CP_INTC_VIRT, DA830_N_CP_INTC_IRQ, - soc_info->intc_irq_prios); -} - static void __init da830_evm_map_io(void) { da830_init(); } -MACHINE_START(DAVINCI_DA830_EVM, "DaVinci DA830/OMAP-L137 EVM") - .phys_io = IO_PHYS, - .io_pg_offst = (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc, - .boot_params = (DA8XX_DDR_BASE + 0x100), +MACHINE_START(DAVINCI_DA830_EVM, "DaVinci DA830/OMAP-L137/AM17x EVM") + .atag_offset = 0x100, .map_io = da830_evm_map_io, - .init_irq = da830_evm_irq_init, - .timer = &davinci_timer, + .init_irq = cp_intc_init, + .init_time = davinci_timer_init, .init_machine = da830_evm_init, + .init_late = davinci_init_late, + .dma_zone_size = SZ_128M, + .restart = da8xx_restart, MACHINE_END |