diff options
Diffstat (limited to 'arch/arm/mach-at91/board-stamp9g20.c')
| -rw-r--r-- | arch/arm/mach-at91/board-stamp9g20.c | 161 |
1 files changed, 72 insertions, 89 deletions
diff --git a/arch/arm/mach-at91/board-stamp9g20.c b/arch/arm/mach-at91/board-stamp9g20.c index 5206eef4a67..3b575036ff9 100644 --- a/arch/arm/mach-at91/board-stamp9g20.c +++ b/arch/arm/mach-at91/board-stamp9g20.c @@ -25,65 +25,22 @@ #include <asm/mach-types.h> #include <asm/mach/arch.h> -#include <mach/board.h> #include <mach/at91sam9_smc.h> +#include <mach/hardware.h> +#include "at91_aic.h" +#include "board.h" #include "sam9_smc.h" #include "generic.h" +#include "gpio.h" -static void __init portuxg20_map_io(void) +void __init stamp9g20_init_early(void) { /* Initialize processor: 18.432 MHz crystal */ - at91sam9260_initialize(18432000); - - /* DGBU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR - | ATMEL_UART_DCD | ATMEL_UART_RI); - - /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */ - at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); - - /* USART2 on ttyS3. (Rx, Tx, CTS, RTS) */ - at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | ATMEL_UART_RTS); - - /* USART4 on ttyS5. (Rx, Tx only) */ - at91_register_uart(AT91SAM9260_ID_US4, 5, 0); - - /* USART5 on ttyS6. (Rx, Tx only) */ - at91_register_uart(AT91SAM9260_ID_US5, 6, 0); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); + at91_initialize(18432000); } -static void __init stamp9g20_map_io(void) -{ - /* Initialize processor: 18.432 MHz crystal */ - at91sam9260_initialize(18432000); - - /* DGBU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR - | ATMEL_UART_DCD | ATMEL_UART_RI); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); -} - -static void __init init_irq(void) -{ - at91sam9260_init_interrupts(NULL); -} - - /* * NAND flash */ @@ -93,6 +50,8 @@ static struct atmel_nand_data __initdata nand_data = { .rdy_pin = AT91_PIN_PC13, .enable_pin = AT91_PIN_PC14, .bus_width_16 = 0, + .det_pin = -EINVAL, + .ecc_mode = NAND_ECC_SOFT, }; static struct sam9_smc_config __initdata nand_smc_config = { @@ -116,7 +75,7 @@ static struct sam9_smc_config __initdata nand_smc_config = { static void __init add_device_nand(void) { /* configure chip-select 3 (NAND) */ - sam9_smc_configure(3, &nand_smc_config); + sam9_smc_configure(0, 3, &nand_smc_config); at91_add_device_nand(&nand_data); } @@ -126,18 +85,13 @@ static void __init add_device_nand(void) * MCI (SD/MMC) * det_pin, wp_pin and vcc_pin are not connected */ -#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) static struct mci_platform_data __initdata mmc_data = { .slot[0] = { .bus_width = 4, + .detect_pin = -1, + .wp_pin = -1, }, }; -#else -static struct at91_mmc_data __initdata mmc_data = { - .slot_b = 0, - .wire4 = 1, -}; -#endif /* @@ -145,6 +99,8 @@ static struct at91_mmc_data __initdata mmc_data = { */ static struct at91_usbh_data __initdata usbh_data = { .ports = 2, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; @@ -153,19 +109,19 @@ static struct at91_usbh_data __initdata usbh_data = { */ static struct at91_udc_data __initdata portuxg20_udc_data = { .vbus_pin = AT91_PIN_PC7, - .pullup_pin = 0, /* pull-up driven by UDC */ + .pullup_pin = -EINVAL, /* pull-up driven by UDC */ }; -static struct at91_udc_data __initdata stamp9g20_udc_data = { +static struct at91_udc_data __initdata stamp9g20evb_udc_data = { .vbus_pin = AT91_PIN_PA22, - .pullup_pin = 0, /* pull-up driven by UDC */ + .pullup_pin = -EINVAL, /* pull-up driven by UDC */ }; /* * MACB Ethernet device */ -static struct at91_eth_data __initdata macb_data = { +static struct macb_platform_data __initdata macb_data = { .phy_irq_pin = AT91_PIN_PA28, .is_rmii = 1, }; @@ -190,7 +146,7 @@ static struct gpio_led portuxg20_leds[] = { } }; -static struct gpio_led stamp9g20_leds[] = { +static struct gpio_led stamp9g20evb_leds[] = { { .name = "D8", .gpio = AT91_PIN_PB18, @@ -234,6 +190,7 @@ static struct spi_board_info portuxg20_spi_devices[] = { static struct w1_gpio_platform_data w1_gpio_pdata = { .pin = AT91_PIN_PA29, .is_open_drain = 1, + .ext_pullup_enable_pin = -EINVAL, }; static struct platform_device w1_device = { @@ -250,62 +207,88 @@ void add_w1(void) } -static void __init generic_board_init(void) +void __init stamp9g20_board_init(void) { /* Serial */ + /* DGBU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); at91_add_device_serial(); /* NAND */ add_device_nand(); /* MMC */ -#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) at91_add_device_mci(0, &mmc_data); -#else - at91_add_device_mmc(0, &mmc_data); -#endif - /* USB Host */ - at91_add_device_usbh(&usbh_data); - /* Ethernet */ - at91_add_device_eth(&macb_data); - /* I2C */ - at91_add_device_i2c(NULL, 0); /* W1 */ add_w1(); } static void __init portuxg20_board_init(void) { - generic_board_init(); - /* SPI */ - at91_add_device_spi(portuxg20_spi_devices, ARRAY_SIZE(portuxg20_spi_devices)); + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR + | ATMEL_UART_DCD | ATMEL_UART_RI); + + /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */ + at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); + + /* USART2 on ttyS3. (Rx, Tx, CTS, RTS) */ + at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | ATMEL_UART_RTS); + + /* USART4 on ttyS5. (Rx, Tx only) */ + at91_register_uart(AT91SAM9260_ID_US4, 5, 0); + + /* USART5 on ttyS6. (Rx, Tx only) */ + at91_register_uart(AT91SAM9260_ID_US5, 6, 0); + stamp9g20_board_init(); + /* USB Host */ + at91_add_device_usbh(&usbh_data); /* USB Device */ at91_add_device_udc(&portuxg20_udc_data); + /* Ethernet */ + at91_add_device_eth(&macb_data); + /* I2C */ + at91_add_device_i2c(NULL, 0); + /* SPI */ + at91_add_device_spi(portuxg20_spi_devices, ARRAY_SIZE(portuxg20_spi_devices)); /* LEDs */ at91_gpio_leds(portuxg20_leds, ARRAY_SIZE(portuxg20_leds)); } -static void __init stamp9g20_board_init(void) +static void __init stamp9g20evb_board_init(void) { - generic_board_init(); + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR + | ATMEL_UART_DCD | ATMEL_UART_RI); + stamp9g20_board_init(); + /* USB Host */ + at91_add_device_usbh(&usbh_data); /* USB Device */ - at91_add_device_udc(&stamp9g20_udc_data); + at91_add_device_udc(&stamp9g20evb_udc_data); + /* Ethernet */ + at91_add_device_eth(&macb_data); + /* I2C */ + at91_add_device_i2c(NULL, 0); /* LEDs */ - at91_gpio_leds(stamp9g20_leds, ARRAY_SIZE(stamp9g20_leds)); + at91_gpio_leds(stamp9g20evb_leds, ARRAY_SIZE(stamp9g20evb_leds)); } MACHINE_START(PORTUXG20, "taskit PortuxG20") /* Maintainer: taskit GmbH */ - .boot_params = AT91_SDRAM_BASE + 0x100, - .timer = &at91sam926x_timer, - .map_io = portuxg20_map_io, - .init_irq = init_irq, + .init_time = at91sam926x_pit_init, + .map_io = at91_map_io, + .handle_irq = at91_aic_handle_irq, + .init_early = stamp9g20_init_early, + .init_irq = at91_init_irq_default, .init_machine = portuxg20_board_init, MACHINE_END MACHINE_START(STAMP9G20, "taskit Stamp9G20") /* Maintainer: taskit GmbH */ - .boot_params = AT91_SDRAM_BASE + 0x100, - .timer = &at91sam926x_timer, - .map_io = stamp9g20_map_io, - .init_irq = init_irq, - .init_machine = stamp9g20_board_init, + .init_time = at91sam926x_pit_init, + .map_io = at91_map_io, + .handle_irq = at91_aic_handle_irq, + .init_early = stamp9g20_init_early, + .init_irq = at91_init_irq_default, + .init_machine = stamp9g20evb_board_init, MACHINE_END |