diff options
Diffstat (limited to 'arch/arm/mach-at91/board-picotux200.c')
| -rw-r--r-- | arch/arm/mach-at91/board-picotux200.c | 93 |
1 files changed, 29 insertions, 64 deletions
diff --git a/arch/arm/mach-at91/board-picotux200.c b/arch/arm/mach-at91/board-picotux200.c index 9d833bbc592..2c0f2d554d8 100644 --- a/arch/arm/mach-at91/board-picotux200.c +++ b/arch/arm/mach-at91/board-picotux200.c @@ -20,6 +20,7 @@ */ #include <linux/types.h> +#include <linux/gpio.h> #include <linux/init.h> #include <linux/mm.h> #include <linux/module.h> @@ -36,74 +37,40 @@ #include <asm/mach/map.h> #include <asm/mach/irq.h> -#include <mach/board.h> -#include <mach/gpio.h> #include <mach/at91rm9200_mc.h> +#include <mach/at91_ramc.h> +#include "at91_aic.h" +#include "board.h" #include "generic.h" +#include "gpio.h" -/* - * Serial port configuration. - * 0 .. 3 = USART0 .. USART3 - * 4 = DBGU - */ -static struct at91_uart_config __initdata picotux200_uart_config = { - .console_tty = 0, /* ttyS0 */ - .nr_tty = 2, - .tty_map = { 4, 1, -1, -1, -1 } /* ttyS0, ..., ttyS4 */ -}; - -static void __init picotux200_map_io(void) +static void __init picotux200_init_early(void) { /* Initialize processor: 18.432 MHz crystal */ - at91rm9200_initialize(18432000, AT91RM9200_BGA); - - /* Setup the serial ports and console */ - at91_init_serial(&picotux200_uart_config); + at91_initialize(18432000); } -static void __init picotux200_init_irq(void) -{ - at91rm9200_init_interrupts(NULL); -} - -static struct at91_eth_data __initdata picotux200_eth_data = { +static struct macb_platform_data __initdata picotux200_eth_data = { .phy_irq_pin = AT91_PIN_PC4, .is_rmii = 1, }; static struct at91_usbh_data __initdata picotux200_usbh_data = { .ports = 1, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; -// static struct at91_udc_data __initdata picotux200_udc_data = { -// .vbus_pin = AT91_PIN_PD4, -// .pullup_pin = AT91_PIN_PD5, -// }; - -static struct at91_mmc_data __initdata picotux200_mmc_data = { - .det_pin = AT91_PIN_PB27, - .slot_b = 0, - .wire4 = 1, - .wp_pin = AT91_PIN_PA17, +static struct mci_platform_data __initdata picotux200_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PB27, + .wp_pin = AT91_PIN_PA17, + }, }; -// static struct spi_board_info picotux200_spi_devices[] = { -// { /* DataFlash chip */ -// .modalias = "mtd_dataflash", -// .chip_select = 0, -// .max_speed_hz = 15 * 1000 * 1000, -// }, -// #ifdef CONFIG_MTD_AT91_DATAFLASH_CARD -// { /* DataFlash card */ -// .modalias = "mtd_dataflash", -// .chip_select = 3, -// .max_speed_hz = 15 * 1000 * 1000, -// }, -// #endif -// }; - #define PICOTUX200_FLASH_BASE AT91_CHIPSELECT_0 #define PICOTUX200_FLASH_SIZE SZ_4M @@ -130,35 +97,33 @@ static struct platform_device picotux200_flash = { static void __init picotux200_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); at91_add_device_serial(); /* Ethernet */ at91_add_device_eth(&picotux200_eth_data); /* USB Host */ at91_add_device_usbh(&picotux200_usbh_data); - /* USB Device */ - // at91_add_device_udc(&picotux200_udc_data); - // at91_set_multi_drive(picotux200_udc_data.pullup_pin, 1); /* pullup_pin is connected to reset */ /* I2C */ at91_add_device_i2c(NULL, 0); - /* SPI */ - // at91_add_device_spi(picotux200_spi_devices, ARRAY_SIZE(picotux200_spi_devices)); -#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD - /* DataFlash card */ - at91_set_gpio_output(AT91_PIN_PB22, 0); -#else /* MMC */ at91_set_gpio_output(AT91_PIN_PB22, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */ - at91_add_device_mmc(0, &picotux200_mmc_data); -#endif + at91_add_device_mci(0, &picotux200_mci0_data); /* NOR Flash */ platform_device_register(&picotux200_flash); } MACHINE_START(PICOTUX2XX, "picotux 200") /* Maintainer: Kleinhenz Elektronik GmbH */ - .boot_params = AT91_SDRAM_BASE + 0x100, - .timer = &at91rm9200_timer, - .map_io = picotux200_map_io, - .init_irq = picotux200_init_irq, + .init_time = at91rm9200_timer_init, + .map_io = at91_map_io, + .handle_irq = at91_aic_handle_irq, + .init_early = picotux200_init_early, + .init_irq = at91_init_irq_default, .init_machine = picotux200_board_init, MACHINE_END |