diff options
Diffstat (limited to 'arch/arm/mach-at91/board-neocore926.c')
| -rw-r--r-- | arch/arm/mach-at91/board-neocore926.c | 395 |
1 files changed, 0 insertions, 395 deletions
diff --git a/arch/arm/mach-at91/board-neocore926.c b/arch/arm/mach-at91/board-neocore926.c deleted file mode 100644 index fe5f1d47e6e..00000000000 --- a/arch/arm/mach-at91/board-neocore926.c +++ /dev/null @@ -1,395 +0,0 @@ -/* - * linux/arch/arm/mach-at91/board-neocore926.c - * - * Copyright (C) 2005 SAN People - * Copyright (C) 2007 Atmel Corporation - * Copyright (C) 2008 ADENEO. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include <linux/types.h> -#include <linux/init.h> -#include <linux/mm.h> -#include <linux/module.h> -#include <linux/platform_device.h> -#include <linux/spi/spi.h> -#include <linux/spi/ads7846.h> -#include <linux/fb.h> -#include <linux/gpio_keys.h> -#include <linux/input.h> - -#include <video/atmel_lcdc.h> - -#include <asm/setup.h> -#include <asm/mach-types.h> -#include <asm/irq.h> -#include <asm/sizes.h> - -#include <asm/mach/arch.h> -#include <asm/mach/map.h> -#include <asm/mach/irq.h> - -#include <mach/hardware.h> -#include <mach/board.h> -#include <mach/gpio.h> -#include <mach/at91sam9_smc.h> - -#include "sam9_smc.h" -#include "generic.h" - - -static void __init neocore926_map_io(void) -{ - /* Initialize processor: 20 MHz crystal */ - at91sam9263_initialize(20000000); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */ - at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); -} - -static void __init neocore926_init_irq(void) -{ - at91sam9263_init_interrupts(NULL); -} - - -/* - * USB Host port - */ -static struct at91_usbh_data __initdata neocore926_usbh_data = { - .ports = 2, - .vbus_pin = { AT91_PIN_PA24, AT91_PIN_PA21 }, -}; - -/* - * USB Device port - */ -static struct at91_udc_data __initdata neocore926_udc_data = { - .vbus_pin = AT91_PIN_PA25, - .pullup_pin = 0, /* pull-up driven by UDC */ -}; - - -/* - * ADS7846 Touchscreen - */ -#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE) -static int ads7843_pendown_state(void) -{ - return !at91_get_gpio_value(AT91_PIN_PA15); /* Touchscreen PENIRQ */ -} - -static struct ads7846_platform_data ads_info = { - .model = 7843, - .x_min = 150, - .x_max = 3830, - .y_min = 190, - .y_max = 3830, - .vref_delay_usecs = 100, - .x_plate_ohms = 450, - .y_plate_ohms = 250, - .pressure_max = 15000, - .debounce_max = 1, - .debounce_rep = 0, - .debounce_tol = (~0), - .get_pendown_state = ads7843_pendown_state, -}; - -static void __init neocore926_add_device_ts(void) -{ - at91_set_B_periph(AT91_PIN_PA15, 1); /* External IRQ1, with pullup */ - at91_set_gpio_input(AT91_PIN_PC13, 1); /* Touchscreen BUSY signal */ -} -#else -static void __init neocore926_add_device_ts(void) {} -#endif - -/* - * SPI devices. - */ -static struct spi_board_info neocore926_spi_devices[] = { -#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD) - { /* DataFlash card */ - .modalias = "mtd_dataflash", - .chip_select = 0, - .max_speed_hz = 15 * 1000 * 1000, - .bus_num = 0, - }, -#endif -#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE) - { - .modalias = "ads7846", - .chip_select = 1, - .max_speed_hz = 125000 * 16, - .bus_num = 0, - .platform_data = &ads_info, - .irq = AT91SAM9263_ID_IRQ1, - }, -#endif -}; - - -/* - * MCI (SD/MMC) - */ -static struct at91_mmc_data __initdata neocore926_mmc_data = { - .wire4 = 1, - .det_pin = AT91_PIN_PE18, - .wp_pin = AT91_PIN_PE19, -}; - - -/* - * MACB Ethernet device - */ -static struct at91_eth_data __initdata neocore926_macb_data = { - .phy_irq_pin = AT91_PIN_PE31, - .is_rmii = 1, -}; - - -/* - * NAND flash - */ -static struct mtd_partition __initdata neocore926_nand_partition[] = { - { - .name = "Linux Kernel", /* "Partition 1", */ - .offset = 0, - .size = SZ_8M, - }, - { - .name = "Filesystem", /* "Partition 2", */ - .offset = MTDPART_OFS_NXTBLK, - .size = SZ_32M, - }, - { - .name = "Free", /* "Partition 3", */ - .offset = MTDPART_OFS_NXTBLK, - .size = MTDPART_SIZ_FULL, - }, -}; - -static struct mtd_partition * __init nand_partitions(int size, int *num_partitions) -{ - *num_partitions = ARRAY_SIZE(neocore926_nand_partition); - return neocore926_nand_partition; -} - -static struct atmel_nand_data __initdata neocore926_nand_data = { - .ale = 21, - .cle = 22, - .rdy_pin = AT91_PIN_PB19, - .rdy_pin_active_low = 1, - .enable_pin = AT91_PIN_PD15, - .partition_info = nand_partitions, -}; - -static struct sam9_smc_config __initdata neocore926_nand_smc_config = { - .ncs_read_setup = 0, - .nrd_setup = 1, - .ncs_write_setup = 0, - .nwe_setup = 1, - - .ncs_read_pulse = 4, - .nrd_pulse = 4, - .ncs_write_pulse = 4, - .nwe_pulse = 4, - - .read_cycle = 6, - .write_cycle = 6, - - .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8, - .tdf_cycles = 2, -}; - -static void __init neocore926_add_device_nand(void) -{ - /* configure chip-select 3 (NAND) */ - sam9_smc_configure(3, &neocore926_nand_smc_config); - - at91_add_device_nand(&neocore926_nand_data); -} - - -/* - * LCD Controller - */ -#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE) -static struct fb_videomode at91_tft_vga_modes[] = { - { - .name = "TX09D50VM1CCA @ 60", - .refresh = 60, - .xres = 240, .yres = 320, - .pixclock = KHZ2PICOS(5000), - - .left_margin = 1, .right_margin = 33, - .upper_margin = 1, .lower_margin = 0, - .hsync_len = 5, .vsync_len = 1, - - .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT, - .vmode = FB_VMODE_NONINTERLACED, - }, -}; - -static struct fb_monspecs at91fb_default_monspecs = { - .manufacturer = "HIT", - .monitor = "TX09D70VM1CCA", - - .modedb = at91_tft_vga_modes, - .modedb_len = ARRAY_SIZE(at91_tft_vga_modes), - .hfmin = 15000, - .hfmax = 64000, - .vfmin = 50, - .vfmax = 150, -}; - -#define AT91SAM9263_DEFAULT_LCDCON2 (ATMEL_LCDC_MEMOR_LITTLE \ - | ATMEL_LCDC_DISTYPE_TFT \ - | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE) - -static void at91_lcdc_power_control(int on) -{ - at91_set_gpio_value(AT91_PIN_PA30, on); -} - -/* Driver datas */ -static struct atmel_lcdfb_info __initdata neocore926_lcdc_data = { - .lcdcon_is_backlight = true, - .default_bpp = 16, - .default_dmacon = ATMEL_LCDC_DMAEN, - .default_lcdcon2 = AT91SAM9263_DEFAULT_LCDCON2, - .default_monspecs = &at91fb_default_monspecs, - .atmel_lcdfb_power_control = at91_lcdc_power_control, - .guard_time = 1, - .lcd_wiring_mode = ATMEL_LCDC_WIRING_RGB555, -}; - -#else -static struct atmel_lcdfb_info __initdata neocore926_lcdc_data; -#endif - - -/* - * GPIO Buttons - */ -#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) -static struct gpio_keys_button neocore926_buttons[] = { - { /* BP1, "leftclic" */ - .code = BTN_LEFT, - .gpio = AT91_PIN_PC5, - .active_low = 1, - .desc = "left_click", - .wakeup = 1, - }, - { /* BP2, "rightclic" */ - .code = BTN_RIGHT, - .gpio = AT91_PIN_PC4, - .active_low = 1, - .desc = "right_click", - .wakeup = 1, - }, -}; - -static struct gpio_keys_platform_data neocore926_button_data = { - .buttons = neocore926_buttons, - .nbuttons = ARRAY_SIZE(neocore926_buttons), -}; - -static struct platform_device neocore926_button_device = { - .name = "gpio-keys", - .id = -1, - .num_resources = 0, - .dev = { - .platform_data = &neocore926_button_data, - } -}; - -static void __init neocore926_add_device_buttons(void) -{ - at91_set_GPIO_periph(AT91_PIN_PC5, 0); /* left button */ - at91_set_deglitch(AT91_PIN_PC5, 1); - at91_set_GPIO_periph(AT91_PIN_PC4, 0); /* right button */ - at91_set_deglitch(AT91_PIN_PC4, 1); - - platform_device_register(&neocore926_button_device); -} -#else -static void __init neocore926_add_device_buttons(void) {} -#endif - - -/* - * AC97 - */ -static struct ac97c_platform_data neocore926_ac97_data = { - .reset_pin = AT91_PIN_PA13, -}; - - -static void __init neocore926_board_init(void) -{ - /* Serial */ - at91_add_device_serial(); - - /* USB Host */ - at91_add_device_usbh(&neocore926_usbh_data); - - /* USB Device */ - at91_add_device_udc(&neocore926_udc_data); - - /* SPI */ - at91_set_gpio_output(AT91_PIN_PE20, 1); /* select spi0 clock */ - at91_add_device_spi(neocore926_spi_devices, ARRAY_SIZE(neocore926_spi_devices)); - - /* Touchscreen */ - neocore926_add_device_ts(); - - /* MMC */ - at91_add_device_mmc(1, &neocore926_mmc_data); - - /* Ethernet */ - at91_add_device_eth(&neocore926_macb_data); - - /* NAND */ - neocore926_add_device_nand(); - - /* I2C */ - at91_add_device_i2c(NULL, 0); - - /* LCD Controller */ - at91_add_device_lcdc(&neocore926_lcdc_data); - - /* Push Buttons */ - neocore926_add_device_buttons(); - - /* AC97 */ - at91_add_device_ac97(&neocore926_ac97_data); -} - -MACHINE_START(NEOCORE926, "ADENEO NEOCORE 926") - /* Maintainer: ADENEO */ - .boot_params = AT91_SDRAM_BASE + 0x100, - .timer = &at91sam926x_timer, - .map_io = neocore926_map_io, - .init_irq = neocore926_init_irq, - .init_machine = neocore926_board_init, -MACHINE_END |