diff options
Diffstat (limited to 'arch/arm/mach-at91/board-ecbat91.c')
| -rw-r--r-- | arch/arm/mach-at91/board-ecbat91.c | 81 |
1 files changed, 48 insertions, 33 deletions
diff --git a/arch/arm/mach-at91/board-ecbat91.c b/arch/arm/mach-at91/board-ecbat91.c index 7b58c948a95..ede1373ccab 100644 --- a/arch/arm/mach-at91/board-ecbat91.c +++ b/arch/arm/mach-at91/board-ecbat91.c @@ -20,6 +20,7 @@ */ #include <linux/types.h> +#include <linux/gpio.h> #include <linux/init.h> #include <linux/mm.h> #include <linux/module.h> @@ -36,47 +37,40 @@ #include <asm/mach/map.h> #include <asm/mach/irq.h> -#include <mach/board.h> -#include <mach/gpio.h> +#include <mach/cpu.h> +#include "at91_aic.h" +#include "board.h" #include "generic.h" +#include "gpio.h" -static void __init ecb_at91map_io(void) +static void __init ecb_at91init_early(void) { - /* Initialize processor: 18.432 MHz crystal */ - at91rm9200_initialize(18432000, AT91RM9200_PQFP); - - /* Setup the LEDs */ - at91_init_leds(AT91_PIN_PC7, AT91_PIN_PC7); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx & Tx only) */ - at91_register_uart(AT91RM9200_ID_US0, 1, 0); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); -} + /* Set cpu type: PQFP */ + at91rm9200_set_type(ARCH_REVISON_9200_PQFP); -static void __init ecb_at91init_irq(void) -{ - at91rm9200_init_interrupts(NULL); + /* Initialize processor: 18.432 MHz crystal */ + at91_initialize(18432000); } -static struct at91_eth_data __initdata ecb_at91eth_data = { +static struct macb_platform_data __initdata ecb_at91eth_data = { .phy_irq_pin = AT91_PIN_PC4, .is_rmii = 0, }; static struct at91_usbh_data __initdata ecb_at91usbh_data = { .ports = 1, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; -static struct at91_mmc_data __initdata ecb_at91mmc_data = { - .slot_b = 0, - .wire4 = 1, +static struct mci_platform_data __initdata ecbat91_mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = -EINVAL, + .wp_pin = -EINVAL, + }, }; @@ -128,26 +122,43 @@ static struct spi_board_info __initdata ecb_at91spi_devices[] = { .platform_data = &my_flash0_platform, #endif }, - { /* User accessable spi - cs1 (250KHz) */ + { /* User accessible spi - cs1 (250KHz) */ .modalias = "spi-cs1", .chip_select = 1, .max_speed_hz = 250 * 1000, }, - { /* User accessable spi - cs2 (1MHz) */ + { /* User accessible spi - cs2 (1MHz) */ .modalias = "spi-cs2", .chip_select = 2, .max_speed_hz = 1 * 1000 * 1000, }, - { /* User accessable spi - cs3 (10MHz) */ + { /* User accessible spi - cs3 (10MHz) */ .modalias = "spi-cs3", .chip_select = 3, .max_speed_hz = 10 * 1000 * 1000, }, }; +/* + * LEDs + */ +static struct gpio_led ecb_leds[] = { + { /* D1 */ + .name = "led1", + .gpio = AT91_PIN_PC7, + .active_low = 1, + .default_trigger = "heartbeat", + } +}; + static void __init ecb_at91board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx & Tx only) */ + at91_register_uart(AT91RM9200_ID_US0, 1, 0); at91_add_device_serial(); /* Ethernet */ @@ -160,17 +171,21 @@ static void __init ecb_at91board_init(void) at91_add_device_i2c(NULL, 0); /* MMC */ - at91_add_device_mmc(0, &ecb_at91mmc_data); + at91_add_device_mci(0, &ecbat91_mci0_data); /* SPI */ at91_add_device_spi(ecb_at91spi_devices, ARRAY_SIZE(ecb_at91spi_devices)); + + /* LEDs */ + at91_gpio_leds(ecb_leds, ARRAY_SIZE(ecb_leds)); } MACHINE_START(ECBAT91, "emQbit's ECB_AT91") /* Maintainer: emQbit.com */ - .boot_params = AT91_SDRAM_BASE + 0x100, - .timer = &at91rm9200_timer, - .map_io = ecb_at91map_io, - .init_irq = ecb_at91init_irq, + .init_time = at91rm9200_timer_init, + .map_io = at91_map_io, + .handle_irq = at91_aic_handle_irq, + .init_early = ecb_at91init_early, + .init_irq = at91_init_irq_default, .init_machine = ecb_at91board_init, MACHINE_END |