diff options
Diffstat (limited to 'arch/arc/plat-arcfpga/platform.c')
| -rw-r--r-- | arch/arc/plat-arcfpga/platform.c | 78 |
1 files changed, 9 insertions, 69 deletions
diff --git a/arch/arc/plat-arcfpga/platform.c b/arch/arc/plat-arcfpga/platform.c index d71f3c3bcf2..61c7e599738 100644 --- a/arch/arc/plat-arcfpga/platform.c +++ b/arch/arc/plat-arcfpga/platform.c @@ -22,59 +22,6 @@ #include <plat/smp.h> #include <plat/irq.h> -/*-----------------------BVCI Latency Unit -----------------------------*/ - -#ifdef CONFIG_ARC_HAS_BVCI_LAT_UNIT - -int lat_cycles = CONFIG_BVCI_LAT_CYCLES; - -/* BVCI Bus Profiler: Latency Unit */ -static void __init setup_bvci_lat_unit(void) -{ -#define MAX_BVCI_UNITS 12 - - unsigned int i; - unsigned int *base = (unsigned int *)BVCI_LAT_UNIT_BASE; - const unsigned long units_req = CONFIG_BVCI_LAT_UNITS; - const unsigned int REG_UNIT = 21; - const unsigned int REG_VAL = 22; - - /* - * There are multiple Latency Units corresponding to the many - * interfaces of the system bus arbiter (both CPU side as well as - * the peripheral side). - * - * Unit 0 - System Arb and Mem Controller - adds latency to all - * memory trasactions - * Unit 1 - I$ and System Bus - * Unit 2 - D$ and System Bus - * .. - * Unit 12 - IDE Disk controller and System Bus - * - * The programmers model requires writing to lat_unit reg first - * and then the latency value (cycles) to lat_value reg - */ - - if (CONFIG_BVCI_LAT_UNITS == 0) { - writel(0, base + REG_UNIT); - writel(lat_cycles, base + REG_VAL); - pr_info("BVCI Latency for all Memory Transactions %d cycles\n", - lat_cycles); - } else { - for_each_set_bit(i, &units_req, MAX_BVCI_UNITS) { - writel(i + 1, base + REG_UNIT); /* loop is 0 based */ - writel(lat_cycles, base + REG_VAL); - pr_info("BVCI Latency for Unit[%d] = %d cycles\n", - (i + 1), lat_cycles); - } - } -} -#else -static void __init setup_bvci_lat_unit(void) -{ -} -#endif - /*----------------------- Platform Devices -----------------------------*/ #if IS_ENABLED(CONFIG_SERIAL_ARC) @@ -132,16 +79,11 @@ static void arc_fpga_serial_init(void) ARRAY_SIZE(fpga_early_devs)); /* - * ARC console driver registers itself as an early platform driver - * of class "earlyprintk". - * Install it here, followed by probe of devices. - * The installation here doesn't require earlyprintk in command line - * To do so however, replace the lines below with - * parse_early_param(); - * early_platform_driver_probe("earlyprintk", 1, 1); - * ^^ + * ARC console driver registers (build time) as an early platform driver + * of class "earlyprintk". However it needs explicit cmdline toggle + * "earlyprintk=ttyARC0" to be successfuly runtime registered. + * Otherwise the early probe below fails to find the driver */ - early_platform_driver_register_all("earlyprintk"); early_platform_driver_probe("earlyprintk", 1, 0); /* @@ -165,11 +107,9 @@ static void __init plat_fpga_early_init(void) { pr_info("[plat-arcfpga]: registering early dev resources\n"); - setup_bvci_lat_unit(); - arc_fpga_serial_init(); -#ifdef CONFIG_SMP +#ifdef CONFIG_ISS_SMP_EXTN iss_model_init_early_smp(); #endif } @@ -201,7 +141,7 @@ static void __init plat_fpga_populate_dev(void) * callback set, by matching the DT compatible name. */ -static const char *aa4_compat[] __initdata = { +static const char *aa4_compat[] __initconst = { "snps,arc-angel4", NULL, }; @@ -211,12 +151,12 @@ MACHINE_START(ANGEL4, "angel4") .init_early = plat_fpga_early_init, .init_machine = plat_fpga_populate_dev, .init_irq = plat_fpga_init_IRQ, -#ifdef CONFIG_SMP +#ifdef CONFIG_ISS_SMP_EXTN .init_smp = iss_model_init_smp, #endif MACHINE_END -static const char *ml509_compat[] __initdata = { +static const char *ml509_compat[] __initconst = { "snps,arc-ml509", NULL, }; @@ -231,7 +171,7 @@ MACHINE_START(ML509, "ml509") #endif MACHINE_END -static const char *nsimosci_compat[] __initdata = { +static const char *nsimosci_compat[] __initconst = { "snps,nsimosci", NULL, }; |