1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
|
<html>
<head>
<title>Test results for revision 607</title>
</head>
<body>
<H1>Test cases</H1>
<H2>Test case results</H2>
The test results are stored in seperate documents. One document for
each subversion number.
<table border="1">
<tr><td>Test results</td><td>comment</td></tr>
<tr><td>607</a></td><td></td></tr>
<tr><td><a href="results/template.html">template</a></td><td>Test results template</td></tr>
</table>
<H1>SAM7S64</H1>
<H2>Connectivity</H2>
<table border=1>
<tr>
<td>ID</td>
<td>Target</td>
<td>Interface</td>
<td>Description</td>
<td>Initial state</td>
<td>Input</td>
<td>Expected output</td>
<td>Actual output</td>
<td>Pass/Fail</td>
</tr>
<tr>
<td><a name="CON001"/>CON001</td>
<td>SAM7S64</td>
<td>ZY1000</td>
<td>Telnet connection</td>
<td>Power on, jtag target attached</td>
<td>On console, type<br><code>telnet ip port</code></td>
<td><code>Open On-Chip Debugger<br>></code></td>
<td><code>Open On-Chip Debugger<br>></code></td>
<td>PASS</td>
</tr>
<tr>
<td><a name="CON002"/>CON002</td>
<td>SAM7S64</td>
<td>ZY1000</td>
<td>GDB server connection</td>
<td>Power on, jtag target attached</td>
<td>On GDB console, type<br><code>target remote ip:port</code></td>
<td><code>Remote debugging using 10.0.0.73:3333</code></td>
<td><code>Remote debugging using 10.0.0.73:3333</code></td>
<td>PASS</td>
</tr>
</table>
<H2>Reset</H2>
<table border=1>
<tr>
<td>ID</td>
<td>Target</td>
<td>Interface</td>
<td>Description</td>
<td>Initial state</td>
<td>Input</td>
<td>Expected output</td>
<td>Actual output</td>
<td>Pass/Fail</td>
</tr>
<tr>
<td><a name="RES001"/>RES001</td>
<td>SAM7S64</td>
<td>ZY1000</td>
<td>Reset halt on a blank target</td>
<td>Erase all the content of the flash</td>
<td>Connect via the telnet interface and type <br><code>reset halt</code></td>
<td>Reset should return without error and the output should contain<br><code>target state: halted<br>pc = 0</code></td>
<td>
<code>
JTAG device found: 0x3f0f0f0f (Manufacturer: 0x787, Part: 0xf0f0, Version: 0x3)<br>
nSRST pulls nTRST, falling back to "reset run_and_halt"<br>
target state: halted<br>
target halted in ARM state due to debug request, current mode: Supervisor<br>
cpsr: 0x60000013 pc: 0x00100178
</code>
</td>
<td>PASS</td>
</tr>
<tr>
<td><a name="RES002"/>RES002</td>
<td>SAM7S64</td>
<td>ZY1000</td>
<td>Reset init on a blank target</td>
<td>Erase all the content of the flash</td>
<td>Connect via the telnet interface and type <br><code>reset init</code></td>
<td>Reset should return without error and the output should contain <br><code>executing reset script 'name_of_the_script'</code></td>
<td>
<code>
JTAG device found: 0x3f0f0f0f (Manufacturer: 0x787, Part: 0xf0f0, Version: 0x3)<br>
nSRST pulls nTRST, falling back to "reset run_and_init"<br>
target state: halted<br>
target halted in ARM state due to debug request, current mode: Supervisor<br>
cpsr: 0x600000d3 pc: 0x00003e24<br>
executing reset script 'event/sam7s256_reset.script'
</code>
</td>
<td>PASS</td>
</tr>
<tr>
<td><a name="RES003"/>RES003</td>
<td>SAM7S64</td>
<td>ZY1000</td>
<td>Reset after a power cycle of the target</td>
<td>Reset the target then power cycle the target</td>
<td>Connect via the telnet interface and type <br><code>reset halt</code> after the power was detected</td>
<td>Reset should return without error and the output should contain<br><code>target state: halted</code></td>
<td>
<code>
JTAG device found: 0x3f0f0f0f (Manufacturer: 0x787, Part: 0xf0f0, Version: 0x3)<br>
nSRST pulls nTRST, falling back to "reset run_and_halt"<br>
target state: halted<br>
target halted in ARM state due to debug request, current mode: Supervisor<br>
cpsr: 0x300000d3 pc: 0x00003a38
</code>
</td>
<td>PASS</td>
</tr>
</table>
<H2>JTAG Speed</H2>
<table border=1>
<tr>
<td>ID</td>
<td>Target</td>
<td>ZY1000</td>
<td>Description</td>
<td>Initial state</td>
<td>Input</td>
<td>Expected output</td>
<td>Actual output</td>
<td>Pass/Fail</td>
</tr>
<tr>
<td><a name="SPD001"/>RES001</td>
<td>SAM7S64</td>
<td>ZY1000</td>
<td>16MHz on normal operation</td>
<td>Reset init the target according to RES002 </td>
<td>Exercise a memory access over the JTAG, for example <br><code>mdw 0x0 32</code></td>
<td>The command should run without any errors. If any JTAG checking errors happen, the test failed</td>
<td>
<code>
> jtag_khz 16000<br>
> mdw 0 32<br>
0x00000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff<br>
0x00000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff<br>
0x00000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff<br>
0x00000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
</code>
</td>
<td>PASS</td>
</tr>
</table>
<H2>Debugging</H2>
<table border=1>
<tr>
<td>ID</td>
<td>Target</td>
<td>Interface</td>
<td>Description</td>
<td>Initial state</td>
<td>Input</td>
<td>Expected output</td>
<td>Actual output</td>
<td>Pass/Fail</td>
</tr>
<tr>
<td><a name="DBG001"/>DBG001</td>
<td>SAM7S64</td>
<td>ZY1000</td>
<td>Load is working</td>
<td>Reset init is working, RAM is accesible, GDB server is started</td>
<td>On the console of the OS: <br>
<code>arm-elf-gdb test_ram.elf</code><br>
<code>(gdb) target remote ip:port</code><br>
<code>(gdb) load</load>
</td>
<td>Load should return without error, typical output looks like:<br>
<code>
Loading section .text, size 0x14c lma 0x0<br>
Start address 0x40, load size 332<br>
Transfer rate: 180 bytes/sec, 332 bytes/write.<br>
</code>
</td>
<td><code>
(gdb) load<br>
Loading section .text, size 0x194 lma 0x200000<br>
Start address 0x200040, load size 404<br>
Transfer rate: 17470 bits/sec, 404 bytes/write.
</code></td>
<td>PASS</td>
</tr>
<tr>
<td><a name="DBG002"/>DBG002</td>
<td>SAM7S64</td>
<td>ZY1000</td>
<td>Software breakpoint</td>
<td>Load the test_ram.elf application, use instructions from GDB001</td>
<td>In the GDB console:<br>
<code>
(gdb) monitor arm7_9 sw_bkpts enable<br>
software breakpoints enabled<br>
(gdb) break main<br>
Breakpoint 1 at 0xec: file src/main.c, line 71.<br>
(gdb) continue<br>
Continuing.
</code>
</td>
<td>The software breakpoint should be reached, a typical output looks like:<br>
<code>
target state: halted<br>
target halted in ARM state due to breakpoint, current mode: Supervisor<br>
cpsr: 0x000000d3 pc: 0x000000ec<br>
<br>
Breakpoint 1, main () at src/main.c:71<br>
71 DWORD a = 1;
</code>
</td>
<td>
<code>
(gdb) break main<br>
Breakpoint 2 at 0x200134: file src/main.c, line 69.<br>
(gdb) c<br>
Continuing.<br>
target state: halted<br>
target halted in ARM state due to breakpoint, current mode: Supervisor<br>
cpsr: 0x60000013 pc: 0x00200134<br>
<br>
Breakpoint 2, main () at src/main.c:69<br>
69 DWORD a = 1;
</code>
</td>
<td>PASS</td>
</tr>
<tr>
<td><a name="DBG003"/>DBG003</td>
<td>SAM7S64</td>
<td>ZY1000</td>
<td>Single step in a RAM application</td>
<td>Load the test_ram.elf application, use instructions from GDB001, break in main using the instructions from GDB002</td>
<td>In GDB, type <br><code>(gdb) step</code></td>
<td>The next instruction should be reached, typical output:<br>
<code>
(gdb) step<br>
target state: halted<br>
target halted in ARM state due to single step, current mode: Abort<br>
cpsr: 0x20000097 pc: 0x000000f0<br>
target state: halted<br>
target halted in ARM state due to single step, current mode: Abort<br>
cpsr: 0x20000097 pc: 0x000000f4<br>
72 DWORD b = 2;
</code>
</td>
<td>
<code>
(gdb) step<br>
target state: halted<br>
target halted in ARM state due to single step, current mode: Abort<br>
cpsr: 0x20000097 pc: 0x000000f0<br>
target state: halted<br>
target halted in ARM state due to single step, current mode: Abort<br>
cpsr: 0x20000097 pc: 0x000000f4<br>
72 DWORD b = 2;
</code>
</td>
<td>PASS</td>
</tr>
<tr>
<td><a name="DBG004"/>DBG004</td>
<td>SAM7S64</td>
<td>ZY1000</td>
<td>Software break points are working after a reset</td>
<td>Load the test_ram.elf application, use instructions from GDB001, break in main using the instructions from GDB002</td>
<td>In GDB, type <br><code>
(gdb) monitor reset<br>
(gdb) load<br>
(gdb) continue<br>
</code></td>
<td>The breakpoint should be reached, typical output:<br>
<code>
target state: halted<br>
target halted in ARM state due to breakpoint, current mode: Supervisor<br>
cpsr: 0x000000d3 pc: 0x000000ec<br>
<br>
Breakpoint 1, main () at src/main.c:71<br>
71 DWORD a = 1;
</code>
</td>
<td><code>
(gdb) moni reset<br>
JTAG device found: 0x3f0f0f0f (Manufacturer: 0x787, Part: 0xf0f0, Version: 0x3)<br>
target state: halted<br>
target halted in ARM state due to debug request, current mode: Supervisor<br>
cpsr: 0x600000d3 pc: 0x00003e28<br>
executing reset script 'event/sam7s256_reset.script'<br>
(gdb) load<br>
Loading section .text, size 0x194 lma 0x200000<br>
Start address 0x200040, load size 404<br>
Transfer rate: 20455 bits/sec, 404 bytes/write.<br>
(gdb) continue<br>
Continuing.<br>
target state: halted<br>
target halted in ARM state due to breakpoint, current mode: Supervisor<br>
cpsr: 0x60000013 pc: 0x00200134<br>
<br>
Breakpoint 2, main () at src/main.c:69<br>
69 DWORD a = 1;
</code></td>
<td>PASS</td>
</tr>
<tr>
<td><a name="DBG005"/>DBG005</td>
<td>SAM7S64</td>
<td>ZY1000</td>
<td>Hardware breakpoint</td>
<td>Flash the test_rom.elf application. Make this test after FLA004 has passed</td>
<td>Be sure that <code>gdb_memory_map</code> and <code>gdb_flash_program</code> are enabled. In GDB, type <br>
<code>
(gdb) monitor reset<br>
(gdb) load<br>
Loading section .text, size 0x194 lma 0x100000<br>
Start address 0x100040, load size 404<br>
Transfer rate: 179 bytes/sec, 404 bytes/write.<br>
(gdb) monitor arm7_9 force_hw_bkpts enable<br>
force hardware breakpoints enabled<br>
(gdb) break main<br>
Breakpoint 1 at 0x100134: file src/main.c, line 69.<br>
(gdb) continue<br>
</code>
</td>
<td>The breakpoint should be reached, typical output:<br>
<code>
Continuing.<br>
<br>
Breakpoint 1, main () at src/main.c:69<br>
69 DWORD a = 1;<br>
</code>
</td>
<td>
<code>
(gdb) break main<br>
Breakpoint 1 at 0x100134: file src/main.c, line 69.<br>
(gdb) c<br>
Continuing.<br>
target state: halted<br>
target halted in ARM state due to breakpoint, current mode: Supervisor<br>
cpsr: 0x60000013 pc: 0x00100134<br>
<br>
Breakpoint 1, main () at src/main.c:69<br>
69 DWORD a = 1;
</code>
</td>
<td>PASS</td>
</tr>
<tr>
<td><a name="DBG006"/>DBG006</td>
<td>SAM7S64</td>
<td>ZY1000</td>
<td>Hardware breakpoint is set after a reset</td>
<td>Follow the instructions to flash and insert a hardware breakpoint from DBG005</td>
<td>In GDB, type <br>
<code>
(gdb) monitor reset<br>
(gdb) monitor reg pc 0x100000<br>
pc (/32): 0x00100000<br>
(gdb) continue
</code><br>
where the value inserted in PC is the start address of the application
</td>
<td>The breakpoint should be reached, typical output:<br>
<code>
Continuing.<br>
<br>
Breakpoint 1, main () at src/main.c:69<br>
69 DWORD a = 1;<br>
</code>
</td>
<td>
<code>
Continuing.<br>
target state: halted<br>
target halted in ARM state due to single step, current mode: Supervisor<br>
cpsr: 0x60000013 pc: 0x00100040<br>
target state: halted<br>
target halted in ARM state due to breakpoint, current mode: Supervisor<br>
cpsr: 0x60000013 pc: 0x00100134<br>
<br>
Breakpoint 1, main () at src/main.c:69<br>
69 DWORD a = 1;
</code><br>
<b>Aren't there too many "halted" signs?</b>
</td>
<td>PASS</td>
</tr>
<tr>
<td><a name="DBG007"/>DBG007</td>
<td>SAM7S64</td>
<td>ZY1000</td>
<td>Single step in ROM</td>
<td>Flash the test_rom.elf application and set a breakpoint in main, use DBG005. Make this test after FLA004 has passed</td>
<td>Be sure that <code>gdb_memory_map</code> and <code>gdb_flash_program</code> are enabled. In GDB, type <br>
<code>
(gdb) monitor reset<br>
(gdb) load<br>
Loading section .text, size 0x194 lma 0x100000<br>
Start address 0x100040, load size 404<br>
Transfer rate: 179 bytes/sec, 404 bytes/write.<br>
(gdb) monitor arm7_9 force_hw_bkpts enable<br>
force hardware breakpoints enabled<br>
(gdb) break main<br>
Breakpoint 1 at 0x100134: file src/main.c, line 69.<br>
(gdb) continue<br>
Continuing.<br>
<br>
Breakpoint 1, main () at src/main.c:69<br>
69 DWORD a = 1;<br>
(gdb) step
</code>
</td>
<td>The breakpoint should be reached, typical output:<br>
<code>
target state: halted<br>
target halted in ARM state due to single step, current mode: Supervisor<br>
cpsr: 0x60000013 pc: 0x0010013c<br>
70 DWORD b = 2;<br>
</code>
</td>
<td><code>
(gdb) step<br>
target state: halted<br>
target halted in ARM state due to single step, current mode: Supervisor<br>
cpsr: 0x60000013 pc: 0x00100138<br>
target state: halted<br>
target halted in ARM state due to single step, current mode: Supervisor<br>
cpsr: 0x60000013 pc: 0x0010013c<br>
70 DWORD b = 2;
</code></td>
<td>PASS</td>
</tr>
</table>
<H2>RAM access</H2>
Note: these tests are not designed to test/debug the target, but to test functionalities!
<table border=1>
<tr>
<td>ID</td>
<td>Target</td>
<td>Interface</td>
<td>Description</td>
<td>Initial state</td>
<td>Input</td>
<td>Expected output</td>
<td>Actual output</td>
<td>Pass/Fail</td>
</tr>
<tr>
<td><a name="RAM001"/>RAM001</td>
<td>SAM7S64</td>
<td>ZY1000</td>
<td>32 bit Write/read RAM</td>
<td>Reset init is working</td>
<td>On the telnet interface<br>
<code> > mww ram_address 0xdeadbeef 16<br>
> mdw ram_address 32
</code>
</td>
<td>The commands should execute without error. A clear failure is a memory access exception. The result of running the commands should be a list of 16 locations 32bit long containing 0xdeadbeef.<br>
<code>
> mww 0x0 0xdeadbeef 16<br>
> mdw 0x0 32<br>
0x00000000: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef<br>
0x00000020: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef<br>
0x00000040: e1a00000 e59fa51c e59f051c e04aa000 00080017 00009388 00009388 00009388<br>
0x00000060: 00009388 0002c2c0 0002c2c0 000094f8 000094f4 00009388 00009388 00009388<br>
</code>
</td>
<td>
<code>
> mww 0x00200000 0xdeadbeef 16<br>
> mdw 0x00200000 32<br>
0x00200000: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef<br>
0x00200020: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef<br>
0x00200040: e59f10b4 e3a00902 e5810004 e59f00ac e59f10ac e5810000 e3e010ff e59f00a4<br>
0x00200060: e5810060 e59f10a0 e3e00000 e5810130 e5810124 e321f0db e59fd090 e321f0d7
</code>
</td>
<td>PASS</td>
</tr>
<tr>
<td><a name="RAM002"/>RAM002</td>
<td>SAM7S64</td>
<td>ZY1000</td>
<td>16 bit Write/read RAM</td>
<td>Reset init is working</td>
<td>On the telnet interface<br>
<code> > mwh ram_address 0xbeef 16<br>
> mdh ram_address 32
</code>
</td>
<td>The commands should execute without error. A clear failure is a memory access exception. The result of running the commands should be a list of 16 locations 16bit long containing 0xbeef.<br>
<code>
> mwh 0x0 0xbeef 16<br>
> mdh 0x0 32<br>
0x00000000: beef beef beef beef beef beef beef beef beef beef beef beef beef beef beef beef<br>
0x00000020: 00e0 0000 021c 0000 0240 0000 026c 0000 0288 0000 0000 0000 0388 0000 0350 0000<br>
>
</code>
</td>
<td><code>
> mwh 0x00200000 0xbeef 16<br>
> mdh 0x00200000 32<br>
0x00200000: beef beef beef beef beef beef beef beef beef beef beef beef beef beef beef beef<br>
0x00200020: 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
</code></td>
<td>PASS</td>
</tr>
<tr>
<td><a name="RAM003"/>RAM003</td>
<td>SAM7S64</td>
<td>ZY1000</td>
<td>8 bit Write/read RAM</td>
<td>Reset init is working</td>
<td>On the telnet interface<br>
<code> > mwb ram_address 0xab 16<br>
> mdb ram_address 32
</code>
</td>
<td>The commands should execute without error. A clear failure is a memory access exception. The result of running the commands should be a list of 16 locations 8bit long containing 0xab.<br>
<code>
> mwb ram_address 0xab 16<br>
> mdb ram_address 32<br>
0x00000000: ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00<br>
>
</code>
</td>
<td><code>
> mwb 0x00200000 0xab 16<br>
> mdb 0x00200000 32<br>
0x00200000: ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
</code></td>
<td>PASS</td>
</tr>
</table>
<H2>Flash access</H2>
<table border=1>
<tr>
<td>ID</td>
<td>Target</td>
<td>Interface</td>
<td>Description</td>
<td>Initial state</td>
<td>Input</td>
<td>Expected output</td>
<td>Actual output</td>
<td>Pass/Fail</td>
</tr>
<tr>
<td><a name="FLA001"/>FLA001</td>
<td>SAM7S64</td>
<td>ZY1000</td>
<td>Flash probe</td>
<td>Reset init is working</td>
<td>On the telnet interface:<br>
<code> > flash probe 0</code>
</td>
<td>The command should execute without error. The output should state the name of the flash and the starting address. An example of output:<br>
<code>flash 'ecosflash' found at 0x01000000</code>
</td>
<td>
<code>
> flash probe 0<br>
flash 'at91sam7' found at 0x00100000
</code>
</td>
<td>PASS</td>
</tr>
<tr>
<td><a name="FLA002"/>FLA002</td>
<td>SAM7S64</td>
<td>ZY1000</td>
<td>flash fillw</td>
<td>Reset init is working, flash is probed</td>
<td>On the telnet interface<br>
<code> > flash fillw 0x1000000 0xdeadbeef 16
</code>
</td>
<td>The commands should execute without error. The output looks like:<br>
<code>
wrote 64 bytes to 0x01000000 in 11.610000s (0.091516 kb/s)
</code><br>
To verify the contents of the flash:<br>
<code>
> mdw 0x1000000 32<br>
0x01000000: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef<br>
0x01000020: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef<br>
0x01000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff<br>
0x01000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
</code>
</td>
<td><code>
> flash fillw 0x100000 0xdeadbeef 16<br>
wrote 64 bytes to 0x00100000 in 1.110000s (0.957207 kb/s)<br>
> mdw 0x100000 32<br>
0x00100000: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef<br>
0x00100020: deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef deadbeef<br>
0x00100040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff<br>
0x00100060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
</code></td>
<td>PASS</td>
</tr>
<tr>
<td><a name="FLA003"/>FLA003</td>
<td>SAM7S64</td>
<td>ZY1000</td>
<td>Flash erase</td>
<td>Reset init is working, flash is probed</td>
<td>On the telnet interface<br>
<code> > flash erase_address 0x1000000 0x2000
</code>
</td>
<td>The commands should execute without error.<br>
<code>
erased address 0x01000000 length 8192 in 4.970000s
</code>
To check that the flash has been erased, read at different addresses. The result should always be 0xff.
<code>
> mdw 0x1000000 32<br>
0x01000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff<br>
0x01000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff<br>
0x01000040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff<br>
0x01000060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
</code>
</td>
<td><code>
> flash erase_address 0x100000 0x2000<br>
erased address 0x00100000 length 8192 in 0.510000s<br>
> mdw 0x100000 32<br>
0x00100000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff<br>
0x00100020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff<br>
0x00100040: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff<br>
0x00100060: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff<br>
>
</code></td>
<td>PASS</td>
</tr>
<tr>
<td><a name="FLA004"/>FLA004</td>
<td>SAM7S64</td>
<td>ZY1000</td>
<td>Loading to flash from GDB</td>
<td>Reset init is working, flash is probed, connectivity to GDB server is working</td>
<td>Start GDB using a ROM elf image, eg: arm-elf-gdb test_rom.elf. <br>
<code>
(gdb) target remote ip:port<br>
(gdb) monitor reset<br>
(gdb) load<br>
Loading section .text, size 0x194 lma 0x100000<br>
Start address 0x100040, load size 404<br>
Transfer rate: 179 bytes/sec, 404 bytes/write.
(gdb) monitor verify_image path_to_elf_file
</code>
</td>
<td>The output should look like:<br>
<code>
verified 404 bytes in 5.060000s
</code><br>
The failure message is something like:<br>
<code>Verify operation failed address 0x00200000. Was 0x00 instead of 0x18</code>
</td>
<td>
<code>
(gdb) load<br>
Loading section .text, size 0x194 lma 0x100000<br>
Start address 0x100040, load size 404<br>
Transfer rate: 1540 bits/sec, 404 bytes/write.<br>
(gdb) monitor verify_image /tftp/10.0.0.9/c:\workspace/ecosboard/ecosboard/phi/openocd/rep/testing/examples/SAM7S256Test/test_rom.elf<br>
verified 404 bytes in 4.860000s
</code>
</td>
<td>PASS</td>
</tr>
</table>
</body>
</html>
|
