aboutsummaryrefslogtreecommitdiff
path: root/tcl/target/stm32l0.cfg
blob: ec5d5463ebb1828c07fddf35427f06d4343136ee (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
#
# M0+ devices only have SW-DP, but swj-dp code works, just don't
# set any jtag related features
#

source [find target/swj-dp.tcl]
source [find mem_helper.tcl]

if { [info exists CHIPNAME] } {
   set _CHIPNAME $CHIPNAME
} else {
   set _CHIPNAME stm32l0
}

set _ENDIAN little

# Work-area is a space in RAM used for flash programming
# By default use 2kB (max ram on smallest part)
if { [info exists WORKAREASIZE] } {
   set _WORKAREASIZE $WORKAREASIZE
} else {
   set _WORKAREASIZE 0x800
}

# JTAG speed should be <= F_CPU/6.
# F_CPU after reset is ~2MHz, so use F_JTAG max = 333kHz
adapter_khz 300

adapter_nsrst_delay 100

if { [info exists CPUTAPID] } {
    set _CPUTAPID $CPUTAPID
} else {
    # Arm, m0+, non-multidrop.
    # http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.faqs/ka16088.html
    set _CPUTAPID 0x0bc11477
}

swj_newdap $_CHIPNAME cpu -expected-id $_CPUTAPID
dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu

set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap

$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0

# flash size will be probed
set _FLASHNAME $_CHIPNAME.flash
flash bank $_FLASHNAME stm32lx 0x08000000 0 0 0 $_TARGETNAME

reset_config srst_nogate

if {![using_hla]} {
   # if srst is not fitted use SYSRESETREQ to
   # perform a soft reset
   cortex_m reset_config sysresetreq
}

proc stm32l0_enable_HSI16 {} {
	# Enable HSI16 as clock source
	echo "STM32L0: Enabling HSI16"

	# Set HSI16ON in RCC_CR (leave MSI enabled)
	mww 0x40021000 0x00000101

	# Set HSI16 as SYSCLK (RCC_CFGR)
	mww 0x4002100c 0x00000001

	# Increase speed
	adapter_khz 2500
}

$_TARGETNAME configure -event reset-init {
	stm32l0_enable_HSI16
}

$_TARGETNAME configure -event reset-start {
	adapter_khz 300
}

$_TARGETNAME configure -event examine-end {
	# DBGMCU_CR |= DBG_STANDBY | DBG_STOP | DBG_SLEEP
	mmw 0x40015804 0x00000007 0

	# Stop watchdog counters during halt
	# DBGMCU_APB1_FZ |= DBG_IWDG_STOP | DBG_WWDG_STOP
	mmw 0x40015808 0x00001800 0
}