aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2018-09-17flash/nrf5: time-based timeout waiting for flash controllerKai Geissdoerfer
Change-Id: Id214df154dc359ca130c8d8fe1554d106621b9cd Signed-off-by: Kai Geissdoerfer <kai.geissdoerfer@tu-dresden.de> Reviewed-on: http://openocd.zylin.com/4648 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-09-13arm_adi_v5: remove useless cast to intAntonio Borneo
The field ap_num in struct adiv5_private_config is already of type int. Casting it to type int has no sense. Change-Id: Ida642e808c02591bb58609425eccd096d404e2c4 Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: http://openocd.zylin.com/4666 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-09-12tcl/board: Add Emcraft imx8 SOM BSB supportGuido Günther
Tested with Olimex ARM-USB-TINY-H adapter Simple commands work fine but there are currently issues when attaching remote gdb or running virt2phys: https://sourceforge.net/p/openocd/tickets/201/ Change-Id: I86ccf1d93c5d23870bb522f92b3e2af190d529e8 Signed-off-by: Guido Günther <agx@sigxcpu.org> Reviewed-on: http://openocd.zylin.com/4646 Tested-by: jenkins Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-09-12target/cortex_a: poll all targets in SMP node after haltAntonio Borneo
The periodic poll scans all the targets in the same order they have been declared in the configuration file. When one target in a SMP node halts, the transition is detected in the following poll and this triggers a halt request to all the other cores of the SMP node. The targets that will be polled afterwards will be identified as "halted", but the targets already scanned will remain as "running" until the next periodic poll. This creates a race condition with GDB; GDB sets the breakpoints when runs the target and removes them as soon as the target is halted. When it receives the halt event, it starts removing the breakpoints and fails on the targets that are still reported as "running". Fixed by polling all the targets in the SMP node before informing GDB about the halt event. This implementation is almost copy/paste from the one in aarch64. Change-Id: Id2bd99f1e56b014e48e9e34ccb891b4219c518f8 Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: http://openocd.zylin.com/4622 Tested-by: jenkins Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-09-10ftdi: extend ftdi_location formatOleksij Rempel
To existing <bus>:<port>,<port> format add <bus>-<port>.<port> support. The last format is used by kernel and other drivers. Change-Id: I6528970d3af4f6a8bf7b27a0f7a763b5957fdf2b Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-on: http://openocd.zylin.com/4631 Tested-by: jenkins Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-09-10interface: adapter configuration for FTDI C232HMSteven Stallion
This patch adds support for the C232HM-DDSL-0 and C232HM-EDSL-0 FT232H-based cables from FTDI. For more information, see: http://www.ftdichip.com/Products/Cables/USBMPSSE.htm Change-Id: Ic97423eb1e2f6b5ebae04943cd5cce86f38771d5 Signed-off-by: Steven Stallion <stallion@squareup.com> Reviewed-on: http://openocd.zylin.com/4081 Tested-by: jenkins Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-09-10target/mem_ap: generic mem-ap targetMatthias Welwarsky
This pseudo target allows attaching to any access point on the DAP at the MEM-AP level and read and write addresses on the connected bus. For example, one can create a mem_ap target on the APB-AP and read and write registers of debug components directly. This allows many diagnostic and other features be programmed entirely using TCL, without necessity of adding drivers to OpenOCD. Change-Id: I53229ffd68fb0f96fb68be15b0f3a76cc8843c8e Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com> Reviewed-on: http://openocd.zylin.com/4002 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-by: Leonard Crestez <cdleonard@gmail.com>
2018-09-09flash/stm32f2x: add stm32f7 revision Z identificationCody Schafer
Signed-off-by: Cody P Schafer <openocd@codyps.com> Change-Id: Ia0169514d494bae2a98d92ebc97c8eccc10bc6c4 Reviewed-on: http://openocd.zylin.com/4657 Tested-by: jenkins Reviewed-by: Christopher Head <chead@zaber.com> Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-09-07rtos-helpers: fix minor typo in uC/OS-III helperSteven Stallion
This patch corrects a spelling error in uCOS-III-openocd.c. Change-Id: I6d1923ff1f5e6361358c45cec3dd6c08ca9ccef0 Signed-off-by: Steven Stallion <stallion@squareup.com> Reviewed-on: http://openocd.zylin.com/4659 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2018-09-07libusb: return oocd error valuesOleksij Rempel
keep same return style where possible Change-Id: I2f9b85dbc307a483609f76a84de77e3c74d346c7 Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-on: http://openocd.zylin.com/4588 Tested-by: jenkins Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-09-07gdb_server: add per target option "-gdb-port"Antonio Borneo
The argument passed to global config command "gdb_port" is usually, but not always, a TCP port number. In case of multiple targets, this numeric value is used as the first port of a set of consecutive TCP ports assigned one per target. If the argument is not a numeric value (e.g. "pipe", "disabled", ...) then incrementing it for the next target has no sense. Add the option "-gdb-port number" to the commands "target create" and "$target_name configure" to override, for the specific target, the general global configuration. This permits to use a per target "-gdb-port disabled", when no gdb port is required for that specific target. It also makes possible to choose a custom TCP port number for each target, overriding the usual sequence of consecutive port numbers. Change-Id: I3b9a1910b28ab4bc757e839d0e5d08ffc29f7ab4 Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: http://openocd.zylin.com/4530 Tested-by: jenkins Reviewed-by: Christopher Head <chead@zaber.com> Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-09-07adi_v5: enforce check on AP number valueAntonio Borneo
The AP number value is restricted in 8 bits unsigned by ADI-v5 specification. Nevertheless, an "invalid" value is used by target cortex-m to force an automatic detection of the AP. Replace magic numbers by using new macros for AP max number and for the value of AP invalid. Check the value passed through -ap-num flag during configuration. Change-Id: Ic19a367db0ab11c0ebd070750eca0647d25279a5 Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: http://openocd.zylin.com/4668 Tested-by: jenkins Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-08-22target: armv8: Ensure target is halted for virt2physGuido Günther
Othewise the error reported as Timeout waiting for dpm prepare Change-Id: Ieed2fdcd94ae4e877a749df3eec07a01dbf80b10 Closes: https://sourceforge.net/p/openocd/tickets/201/ Found-by: Matthias Welwarsky <matthias@welwarsky.de> Signed-off-by: Guido Günther <guido.gunther@puri.sm> Reviewed-on: http://openocd.zylin.com/4647 Tested-by: jenkins Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-08-21rtos/linux.c: fix clang static analyzer warningTomas Vanek
Remove sizeof(int64_t) from string size computation. Change-Id: I029b394df5d62a2594a723c4c0e13608b3423b9b Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-on: http://openocd.zylin.com/4640 Tested-by: jenkins
2018-08-21flash/at91sam4: fix clang static analyzer warningTomas Vanek
Change-Id: I5e5319d855c868adfa012f68086f7f809ec5a069 Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-on: http://openocd.zylin.com/4639 Tested-by: jenkins
2018-08-21flash/at91sam4: set wait states only once per writeTomas Vanek
Read-modify-write setting of FMR register requires an USB turnaround. Setting FMR before each page write is not necessary and decreases the write speed. Change-Id: I67844c898aaf117f155c762c979840b603c767ed Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-on: http://openocd.zylin.com/4611 Tested-by: jenkins Reviewed-by: Svetoslav Enchev <svetoslav.enchev@gmail.com>
2018-08-21flash/at91sam4: emit flash bank infoTomas Vanek
Change related LOG_INFO to LOG_DEBUG Change-Id: I0c09b1ec83da631b26980dc8632b9031fe2921a3 Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-on: http://openocd.zylin.com/4610 Tested-by: jenkins Reviewed-by: Erwin Oegema <blablaechthema@hotmail.com> Reviewed-by: Svetoslav Enchev <svetoslav.enchev@gmail.com>
2018-08-21flash/at91sam4: run probe just onceTomas Vanek
Reread registers in sam4_GetInfo() Change-Id: I3b023b3e642a9c052b5c41673d196317f7e7f2e3 Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-on: http://openocd.zylin.com/4609 Tested-by: jenkins Reviewed-by: Erwin Oegema <blablaechthema@hotmail.com> Reviewed-by: Svetoslav Enchev <svetoslav.enchev@gmail.com>
2018-08-21max32xxx: Support for MAX32XXX devices.Kevin Gillespie
Adding flash programming support for Maxim Integrated MAX32XXX devices. Change-Id: I5b0f57a885f9d813240e4bc2d9f765b743e1cfc3 Signed-off-by: Kevin Gillespie <kgills@gmail.com> Reviewed-on: http://openocd.zylin.com/3543 Tested-by: jenkins Reviewed-by: Ismail H. KOSE <ihkose@gmail.com> Reviewed-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2018-08-14target/riscv/riscv-011: fix compile warning about uninitialized variableSvetoslav Enchev
In MSYS2 MinGW 64-bit git clone git://git.code.sf.net/p/openocd/code openocd $ gcc --version gcc.exe (Rev1, Built by MSYS2 project) 8.2.0 ./bootstrap ./configure --prefix= $ cat config.status | grep CFLAGS CFLAGS='-g -O2' make bindir = "bin-x64" depbase=`echo src/target/riscv/riscv-011.lo | sed 's|[^/]*$|.deps/&|;s|\.lo$||'`;\ /bin/sh ./libtool --tag=CC --mode=compile gcc -DHAVE_CONFIG_H -I. -D__USE_MINGW_ANSI_STDIO -I./src -I./src -I./src/helper -DPKGDATADIR=\"/mingw64/share/openocd\" -DBINDIR=\"bin-x64\" -I./jimtcl -I./jimtcl -Wall -Wstrict-prototypes -Wformat-security -Wshadow -Wextra -Wno-unused-parameter -Wbad-function-cast -Wcast-align -Wredundant-decls -Werror -g -O2 -MT src/target/riscv/riscv-011.lo -MD -MP -MF $depbase.Tpo -c -o src/target/riscv/riscv-011.lo src/target/riscv/riscv-011.c &&\ mv -f $depbase.Tpo $depbase.Plo libtool: compile: gcc -DHAVE_CONFIG_H -I. -D__USE_MINGW_ANSI_STDIO -I./src -I./src -I./src/helper -DPKGDATADIR=\"/mingw64/share/openocd\" -DBINDIR=\"bin-x64\" -I./jimtcl -I./jimtcl -Wall -Wstrict-prototypes -Wformat-security -Wshadow -Wextra -Wno-unused-parameter -Wbad-function-cast -Wcast-align -Wredundant-decls -Werror -g -O2 -MT src/target/riscv/riscv-011.lo -MD -MP -MF src/target/riscv/.deps/riscv-011.Tpo -c src/target/riscv/riscv-011.c -o src/target/riscv/riscv-011.o src/target/riscv/riscv-011.c: In function 'poll_target': src/target/riscv/riscv-011.c:1799:6: error: 'reg' may be used uninitialized in this function [-Werror=maybe-uninitialized] reg_cache_set(target, reg, ((data & 0xffffffff) << 32) | value); ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ src/target/riscv/riscv-011.c:1686:17: note: 'reg' was declared here unsigned int reg; ^~~ cc1.exe: all warnings being treated as errors make[2]: *** [Makefile:3250: src/target/riscv/riscv-011.lo] Error 1 Change-Id: I6996dcb866fbace26817636f4bedba09510a087f Signed-off-by: Svetoslav Enchev <svetoslav.enchev@gmail.com> Reviewed-on: http://openocd.zylin.com/4635 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-by: Tim Newsome <tim@sifive.com> Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-08-14tcl/board: update all uses of interface/stlink-v2-1 to interface/stlinkCody P Schafer
Change-Id: I5e27e84d022f73101376e8b4a1bdc65f58fd348a Signed-off-by: Cody P Schafer <openocd@codyps.com> Reviewed-on: http://openocd.zylin.com/4456 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-08-14target/cortex_m: restore C_MASKINTS after resetChristopher Head
The cortex_m maskisr user-facing setting is not changed across a target reset. However, the in-core C_MASKINTS bit was always cleared as part of reset processing, meaning that a cortex_m maskisr on setting would not be respected after a reset. Set C_MASKINTS based on the user-facing setting value rather than always clearing it after reset. Change-Id: I5aa5b9dfde04a0fb9c6816fa55b5ef1faf39f8de Signed-off-by: Christopher Head <chead@zaber.com> Reviewed-on: http://openocd.zylin.com/4605 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-08-14doc: fix typo in cortex_m maskisr commandChristopher Head
Change-Id: I37795c320ff7cbf6f2c7434e03b26dbaf6fc6db4 Signed-off-by: Christopher Head <chead@zaber.com> Reviewed-on: http://openocd.zylin.com/4621 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-08-08Add detail to `wrong register size` error.Tim Newsome
Signed-off-by: Tim Newsome <tim@sifive.com> Change-Id: Id31499c94b539969970251145e42c89c943fd87c Reviewed-on: http://openocd.zylin.com/4577 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-08-08target/armv7a_cache: add gdb keep-alive and fix a missing dpm finishAntonio Borneo
Depending on range size, the loop on cache operations can take quite some time, causing gdb to timeout. Add keep-alive to prevent gdb to timeout. Add also a missing dpm->finish() to balance dpm->prepare(). Change-Id: Ia87934b1ec19a0332bb50e3010b582381e5f3685 Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: http://openocd.zylin.com/4627 Tested-by: jenkins Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-08-06target/cortex_a: allow command dacrfixup during init phaseAntonio Borneo
There is no reason to restrict the command "cortex_a dacrfixup" to the EXEC phase only. Change the command mode to ANY so the command can be used in the initialization phase too. Change-Id: I498cc6b2dbdc48b3b2dd5f0445519a51857b295f Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: http://openocd.zylin.com/4623 Tested-by: jenkins Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-08-06target/arm_adi_v5: allow commands apsel and apcsw during init phaseAntonio Borneo
The current implementation of apsel cannot be executed during the initialization phase because it queries the DAP AP to retrieve and print the content of IDR register, and the query is only possible later on during the exec phase. But IDR information is already printed by the dedicated command apid, making redundant printing it by apsel too. Being unable to run apsel during initialization, makes also apcsw command (that depends on apsel) not usable in such phase. Modify the command apsel to only set the current AP, without making any transfer to the (possibly not initialized yet) DAP. When run without parameters, just print the current AP number. Change mode to COMMAND_ANY to apsel and to apcsw. Change-Id: Ibea6d531e435d1d49d782de1ed8ee6846e91bfdf Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: http://openocd.zylin.com/4624 Tested-by: jenkins Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de> Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-08-02tcl/target: add Allwinner V3s SoC supportOleksij Rempel
Change-Id: I2459d2b137050985b7301047f9651951d72d9e9e Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Reviewed-on: http://openocd.zylin.com/4427 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2018-08-02tcl/target/stm32f0x: Allow overriding the Flash bank sizeDominik Peklo
Copy & paste from another stm32 target. Change-Id: I0f6cbcec974ce70c23c1850526354106caee1172 Signed-off-by: Dominik Peklo <dom.peklo@gmail.com> Reviewed-on: http://openocd.zylin.com/4575 Tested-by: jenkins Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-08-01target/cortex_m: fix incorrect commentChristopher Head
The code sets C_MASKINTS if that bit is not already set (correctly). Fix the comment to agree. Change-Id: If4543e2660a9fa2cdabb2d2698427a6c8d9a274c Signed-off-by: Christopher Head <chead@zaber.com> Reviewed-on: http://openocd.zylin.com/4620 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-08-01server/server: Add ability to remove servicesMarc Schink
Add the ability to remove services while OpenOCD is running. Change-Id: I4067916fda6d03485463fa40901b40484d94e24e Signed-off-by: Marc Schink <openocd-dev@marcschink.de> Reviewed-on: http://openocd.zylin.com/4054 Tested-by: jenkins Reviewed-by: Fredrik Hederstierna <fredrik@hederstierna.com> Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-08-01rtos: add support for NuttXMasatoshi Tateishi
This patch introduces RTOS support for NuttX. Currently, only ARM Cortex-M (both FPU and FPU-less) targets are supported. To use, add the following lines to ~/.gdbinit. define hookpost-file eval "monitor nuttx.pid_offset %d", &((struct tcb_s *)(0))->pid eval "monitor nuttx.xcpreg_offset %d", &((struct tcb_s *)(0))->xcp.regs eval "monitor nuttx.state_offset %d", &((struct tcb_s *)(0))->task_state eval "monitor nuttx.name_offset %d", &((struct tcb_s *)(0))->name eval "monitor nuttx.name_size %d", sizeof(((struct tcb_s *)(0))->name) end And please make sure the above values are the same as in src/rtos/nuttx_header.h Change-Id: I2aaf8644d24dfb84b500516a9685382d5d8fe48f Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com> Signed-off-by: Masatoshi Tateishi <Masatoshi.Tateishi@jp.sony.com> Signed-off-by: Nobuto Kobayashi <Nobuto.Kobayashi@sony.com> Reviewed-on: http://openocd.zylin.com/4103 Tested-by: jenkins Reviewed-by: Alan Carvalho de Assis <acassis@gmail.com> Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-08-01nrf5: add free_driver_privJim Paris
Change-Id: I429a9868deb0c4b51f47a4bbad844bdc348e8d21 Signed-off-by: Jim Paris <jim@jtan.com> Reviewed-on: http://openocd.zylin.com/4608 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-08-01target/arm_adi_v5: add command "dpreg"Antonio Borneo
For very low level debug or development around DAP, it is useful to have direct access to DP registers. Add command "dpreg" by mimic the syntax of the existing "apreg" command: $dap_name dpreg reg [value] Change-Id: Ic4ab451eb5e74453133adee61050b4c6f656ffa3 Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: http://openocd.zylin.com/4612 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-08-01flash/nor/tcl.c: fix flash bank bounds check in 'flash fill' command handlerBohdan Tymkiv
Steps to reproduce ( STM32F103 'Blue Pill', 128KiB of flash ): > flash fillh 0x0801FFFE 00 1 wrote 2 bytes to 0x0801fffe in 0.019088s (0.102 KiB/s) > flash fillw 0x0801FFFE 00 1 Error: stm32f1x.cpu -- clearing lockup after double fault Error: error waiting for target flash write algorithm Error: error writing to flash at address 0x08000000 at offset 0x0001fffe Change-Id: I145092ec5e45bc586b3df48bf37c38c9226915c1 Signed-off-by: Bohdan Tymkiv <bhdt@cypress.com> Reviewed-on: http://openocd.zylin.com/4516 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-08-01zy1000: fix compile error with gcc 8.1.1Antonio Borneo
The fall-through comment is not taken in consideration by gcc 8.1.1 because it is inside the braces of a C-code block. Move the comment outside the C block. Change-Id: I22d87b2dee109fb8bcf2071ac55fdf7171ffcf4b Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: http://openocd.zylin.com/4614 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-08-01server: explicitly call "shutdown" when catch CTRL-C or a signalAntonio Borneo
Every TCL command can be renamed (or deleted) and then replaced by a TCL proc that has the same name of the original TCL command. This can be used either to completely replace an existing command or to wrap the original command to extend its functionality. This applies also to the OpenOCD command "shutdown" and can be useful, for example, to set back some default value to the target before quitting OpenOCD. E.g. (TCL code): rename shutdown original_shutdown proc shutdown {} { puts "This is my implementation of shutdown" # my own stuff before exit OpenOCD original_shutdown } Unfortunately, sending a signal (or pressing CTRL-C) to terminate OpenOCD doesn't trigger calling the original "shutdown" command nor its (eventual) replacement. Detect if the main loop is terminated by an external signal and in such case execute explicitly the command "shutdown". Replace with enum the magic numbers assumed by "shutdown_openocd". Please notice that it's possible to write a custom "shutdown" TCL proc that does not call the original "shutdown" command. This is useful, for example, to prevent the user to quit OpenOCD by typing "shutdown" in the telnet session. Such case will not prevent OpenOCD to terminate when receiving a signal; OpenOCD will quit after executing the custom "shutdown" command. Change-Id: I86b8f9eab8dbd7a28dad58b8cafd97caa7a82f43 Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: http://openocd.zylin.com/4551 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-08-01target/riscv: fix compile error with gcc 8.1.1Antonio Borneo
Fix compile error: src/target/riscv/riscv-011.c: In function ‘slot_offset’: src/target/riscv/riscv-011.c:238:4: error: this statement may fall through [-Werror=implicit-fallthrough=] switch (slot) { ^~~~~~ src/target/riscv/riscv-011.c:243:3: note: here case 64: ^~~~ Fixes: a51ab8ddf63a ("Add RISC-V support.") Change-Id: I7fa86b305bd90cc590fd4359c3698632d44712e5 Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: http://openocd.zylin.com/4618 Tested-by: jenkins Reviewed-by: Jiri Kastner <cz172638@gmail.com> Reviewed-by: Oleksij Rempel <linux@rempel-privat.de> Reviewed-by: Tim Newsome <tim@sifive.com> Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2018-07-31target|board: Add Intel (Altera) Arria 10 target and related boardOleksij Rempel
Target information about this SoC can be found here: https://www.altera.com/products/fpga/arria-series/arria-10/overview.html Achilles Instant-Development Kit Arria 10 SoC SoM: https://www.reflexces.com/products-solutions/development-kits/arria-10/achilles-instant-development-kit-arria-10-soc-som Change-Id: Id78c741be6a8b7d3a70f37d41088e47ee61b437a Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-on: http://openocd.zylin.com/4583 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2018-07-31fpga/altera-10m50: add all device idOleksij Rempel
add all currently know Intel (Alter) MAX 10 device ids Change-Id: I6a88fef222c8e206812499d41be863c3d89fa944 Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-on: http://openocd.zylin.com/4598 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2018-07-31tcl/board: add DPTechnics DPT-Board-v1Oleksij Rempel
it is Atheros AR9331 based IoT dev board. Change-Id: I6fc3cdea1bef49c53045018ff5acfec4d5610ba6 Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Reviewed-on: http://openocd.zylin.com/4424 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2018-07-31tcl/target/atheros_ar9331: add documentation and extra helpersOleksij Rempel
Sync it with experience gathered on Qualcomm QCA4531 SoC. This chips are in many ways similar. Change-Id: I06b9c85e5985a09a9be3cb6cc0ce3b37695d2e54 Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Reviewed-on: http://openocd.zylin.com/4423 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2018-07-31tcl/target/atheros_ar9331: add DDR2 helperOleksij Rempel
this helper works on many different boards, so it is good to have it in target config Change-Id: I068deac36fdd73dbbcedffc87865cc5b9d992c1d Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Reviewed-on: http://openocd.zylin.com/4422 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2018-07-31tcl/target|board: move common AR9331 code to atheros_ar9331.cfgAntony Pavlov
The ar9331_25mhz_pll_init and ar9331_ddr1_init routines can be used not only for TP-Link MR3020 board, so move them to the common atheros_ar9331.cfg file. Change-Id: I04090856b08151d6bb0f5ef9cc654efae1c81835 Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com> Reviewed-on: http://openocd.zylin.com/2999 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2018-07-31tcl/board: add config for 8devices LIMA boardOleksij Rempel
More information about this board can be found here: https://www.8devices.com/products/lima Change-Id: Id35a35d3e986630d58d37b47828870afd107cc6a Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Reviewed-on: http://openocd.zylin.com/4406 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2018-07-31tcl/target: add config for Qualcomm QCA4531Oleksij Rempel
The QCA4531 is a two stream (2x2) 802.11b/g/n single-band programmable Wi-Fi System-on-Chip (SoC) for the Internet of Things (IoT). https://www.qualcomm.com/products/qca4531 Change-Id: I58398c00943b005cfaf0ac1eaad92d1fa4e2cba7 Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Reviewed-on: http://openocd.zylin.com/4405 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2018-07-31mips_m4k: add optional reset handlerOleksij Rempel
In some cases by using SRST we can't halt CPU early enough. And option PrRst is not available too. In this case the only way is to set BOOT flag over EJTAG and reset CPU or SoC from CPU itself. For example by writing to some reset register. This patch is providing possibility to use user defined reset-assert handler which will be enabled only in case SRST is disabled. It is needed to be able switch between two different reset variants on run time. Change-Id: I6ef98f1871ea657115877190f7cc7a5e8f3233e4 Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Reviewed-on: http://openocd.zylin.com/4404 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2018-07-27target/cortex_a: fix compile error for uninitialized variablePaul Bartholomew
Commit ad6c71e151590f9d07eb07eda978a8d2a845259c introduced the variable "mmu_enabled" whose pointer is passed to cortex_a_mmu() that initialises it. This initialization is not visible to the compiler that issue a compile error. The same situation is common across the same file and the usual workaround is to initialize it to zero; thus the same fix i applied here. Ticket: https://sourceforge.net/p/openocd/tickets/197/ Fixes: commit ad6c71e15159 ("cortex_a: fix virt2phys when mmu is disabled") Change-Id: I77dec41acdf4c715b45ae37b72e36719d96d9283 Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: http://openocd.zylin.com/4619 Tested-by: jenkins Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-07-25target/cortex_m: make a variable localChristopher Head
The vec_ids variable is not referenced anywhere other than the vector catch command handler. Make it local to that function. Change-Id: Ie5865e8f78698c19a09f0b9d58269ced1c9db440 Signed-off-by: Christopher Head <chead@zaber.com> Reviewed-on: http://openocd.zylin.com/4606 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-07-25drivers: cmsis-dap: print serial if availableKarl Palsson
Helpful for sanity checking connections Change-Id: Ife0d8b4e12d4c03685aac8115c9739a4c1e994fe Signed-off-by: Karl Palsson <karlp@tweak.net.au> Reviewed-on: http://openocd.zylin.com/3405 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
generated by cgit v1.2.3-18-g5258 (git 2.32.0) at 2025-07-13 02:43:44 +0000