1 files changed, 88 insertions, 0 deletions
diff --git a/tcl/target/stm32g0x.cfg b/tcl/target/stm32g0x.cfg
new file mode 100644
index 00000000..50836ea8
--- /dev/null
+++ b/tcl/target/stm32g0x.cfg
@@ -0,0 +1,88 @@
+# script for stm32g0x family
+
+#
+# stm32g0 devices support SWD transports only.
+#
+source [find target/swj-dp.tcl]
+source [find mem_helper.tcl]
+
+if { [info exists CHIPNAME] } {
+	set _CHIPNAME $CHIPNAME
+} else {
+	set _CHIPNAME stm32g0x
+}
+
+set _ENDIAN little
+
+# Work-area is a space in RAM used for flash programming
+# Smallest proposed target has 8kB ram, use 4kB by default to avoid surprises
+if { [info exists WORKAREASIZE] } {
+	set _WORKAREASIZE $WORKAREASIZE
+} else {
+	set _WORKAREASIZE 0x1000
+}
+
+#jtag scan chain
+if { [info exists CPUTAPID] } {
+	set _CPUTAPID $CPUTAPID
+} else {
+	# Section 37.5.5 - corresponds to Cortex-M0+
+	set _CPUTAPID 0x0bc11477
+}
+
+swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
+
+set _TARGETNAME $_CHIPNAME.cpu
+target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap
+
+$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
+
+set _FLASHNAME $_CHIPNAME.flash
+flash bank $_FLASHNAME stm32l4x 0 0 0 0 $_TARGETNAME
+
+# reasonable default
+adapter speed 2000
+
+adapter srst delay 100
+if {[using_jtag]} {
+	jtag_ntrst_delay 100
+}
+
+reset_config srst_nogate
+
+if {![using_hla]} {
+	# if srst is not fitted use SYSRESETREQ to
+	# perform a soft reset
+	cortex_m reset_config sysresetreq
+}
+
+proc stm32g0x_default_reset_start {} {
+	# Reset clock is HSI16 (16 MHz)
+	adapter speed 2000
+}
+
+proc stm32g0x_default_examine_end {} {
+	# DBGMCU_CR |= DBG_STANDBY | DBG_STOP
+	mmw 0x40015804 0x00000006 0
+
+	# Stop watchdog counters during halt
+	# DBGMCU_APB1_FZ |= DBG_IWDG_STOP | DBG_WWDG_STOP
+	mmw 0x40015808 0x00001800 0
+}
+
+proc stm32g0x_default_reset_init {} {
+	# Increase clock to 64 Mhz
+	mmw 0x40022000 0x00000002 0x00000005	;# FLASH_ACR: Latency = 2
+	mww 0x4002100C 0x30000802				;# RCC_PLLCFGR = PLLR=/2, PLLN=8, PLLM=/1, PLLSRC=0x2
+	mmw 0x40021000 0x01000000 0x00000000	;# RCC_CR |= PLLON
+	mmw 0x40021008 0x00000002 0x00000005	;# RCC_CFGR: SW=PLLRCLK
+
+	# Boost JTAG frequency
+	adapter speed 4000
+}
+
+# Default hooks
+$_TARGETNAME configure -event examine-end { stm32g0x_default_examine_end }
+$_TARGETNAME configure -event reset-start { stm32g0x_default_reset_start }
+$_TARGETNAME configure -event reset-init { stm32g0x_default_reset_init }