aboutsummaryrefslogtreecommitdiff
path: root/drivers/net/wireless/ath/wil6210/wil6210.h
AgeCommit message (Collapse)Author
2014-05-29wil6210: detect scan timeoutsVladimir Kondratiev
If scan has not finished in some reasonable time (10sec), interpret it as if firmware error occurs but was not reported. Firmware should report scan completion for every scan request, so it is error condition indeed. Perform firmware recovery procedure. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-05-29wil6210: limit fw error recovery attemptsVladimir Kondratiev
In case there is something fundamentally wrong with the firmware (example: RF cable disconnected), FW will always crash immediately after reset. This leads to infinite fw error recovery loop. Count consecutive unsuccessful error recovery attempts in a short period of time, and stop doing recovery after some reasonable count. It is still possible to manually reset fw doing interface down/up sequence. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-05-22Merge git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-nextJohn W. Linville
2014-05-19cfg80211: constify MAC addresses in cfg80211 opsJohannes Berg
This propagates through all the drivers and mac80211. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-04-22wil6210: Use larger Tx ringsVladimir Kondratiev
When using scatter-gather, more descriptor entries get used. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-04-22wil6210: relaxed check for BACK start sequenceVladimir Kondratiev
Sometimes, due to the race between Rx path and WMI_BA_STATUS_EVENTID WMI event, few frames may be passed to the stack before reorder buffer allocated. Then, after BACK establishment, it start getting frames with sequence number ahead of SSN, and it get interpreted as missing frames. Then, BACK mechanism will wait for missing frames; data traffic will be stopped. In case of interface configured for DHCP, this data delay causes DHCP failure. Relax checking for sequence number; use sequence of 1-st frame handled by the buffer as SSN for this buffer. This is work-around, real fix should be done when proper BACK mechanism implemented. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: fix race between disconnect and Tx NAPIVladimir Kondratiev
When disconnecting some CID, corresponded Tx vring get released. During vring release, all descriptors get freed. It is possible that Tx NAPI working on the same vring simultaneously. If it happens, descriptor may be double freed. To protect from the race above, make sure NAPI won't process the same vring. Introduce 'enabled' flag in the struct vring_tx_data. Proceed with Tx NAPI only if 'enabled' flag set. Prior to Tx vring release, clear this flag and make sure NAPI get synchronized. NAPI enablement status protected by wil->mutex, add protection where it was missing and check for it. During reset, disconnect all peers first, then proceed with the Rx vring. It allows for the disconnect flow to observe proper 'wil->status' and correctly notify cfg80211 about connection status change Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: target reset flow updateVladimir Kondratiev
Use 'real' indication for hardware state. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: fw error recoveryVladimir Kondratiev
upon fw error interrupt - in STA mode, disconnect/cancel scan and then reset FW/HW added module param - no_fw_recovery which is false by default Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: Fix kernel oops in reset flowVladimir Kondratiev
wil_reset() removes vring's At the same time NAPI may be active performing Rx/Tx completion. If this happens, Rx/Tx polling functions going to access already removed vrings Make sure NAPI is idle and won't be started prior to vring removal. For this, track NAPI enabled state Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: reset on power goodVladimir Kondratiev
Configure hardware to perform full reset on "power good". This mean, reset HW on system boot. This improves card stability. By default this is off. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: sort HW registers definitionsVladimir Kondratiev
Put all registers in order for easier navigation; fix naming to reflect hardware cluster Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: fix for HW bug in interrupt setup logicVladimir Kondratiev
Hardware bug triggered by the MSI init while INTx asserted for some reason. De-assert INTx prior to MSI set-up Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: update target reset to support new HWVladimir Kondratiev
Support for new chip revision. Revision read from the internal register, PCIE config's "revision id" register do not indicate HW version properly Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: generalize tx desc mappingVladimir Kondratiev
Introduce enum to describe mapping type; allow 'none' in addition to 'single' and 'page'; this is preparation for GSO Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: add scatter-gather supportVladimir Kondratiev
When setting fragmented skb for Tx, assign skb to the last descriptor and set number of fragments in the 1-st one On Tx complete, HW sets "DU" bit in Tx descriptor only for the last descriptor; so search for it using number of fragments field. Middle descriptors may have "DU" bit not set by the hardware. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: Block data till "data port open" reportedVladimir Kondratiev
When connection established, as reported by WMI_CONNECT_EVENTID, 4-way handshaking required for the secure connection is not done yet. It is indicated by another WMI event. Wait for it and only then allow data traffic. In case of non-secure connection, FW reports "data port open" immediately after connection. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: Helpers to deal with 'cidxtid' fieldsVladimir Kondratiev
Encode/decode helpers Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28wil6210: single station disconnectVladimir Kondratiev
implement del_station() method in the struct cfg80211_ops It allows to disconnect single peer from the AP Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28wil6210: per-connection statisticsVladimir Kondratiev
Calculate statistics per connection, report with "iw station dump" Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28wil6210: Block ACKVladimir Kondratiev
When running multiple connections, hardware can't do BACK reordering and it should be done on the host. Model after mac80211's implementation. Drop RCU for now; to be re-added when BACK will be stabilized BACK handshaking is not implemented yet in the hardware, pretend it was done to support the way FW operating Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28wil6210: multiple connect - initial supportVladimir Kondratiev
Enable multiple (up to 8 - HW/FW limitation) simultaneous connections. Each connection has its own CID (connection ID) that describes chip's beam-forming entity. Tx Vring should refer to correct CID for frame to reach its destination. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28wil6210: Tx management frameVladimir Kondratiev
Implement management frame passing. In order to receive frame on the other side, remain_on_channel() should be implemented as well Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-01-09wil6210: interrupt moderationVladimir Kondratiev
Use hardware capabilities to limit IRQ generation to about 15 per msec It corresponds to about 7 packets/IRQ when running iperf with default parameters at 1.3Gbps Do not enable this feature in the sniffer (monitor) mode, because interrupt moderation cause timestamp accuracy deterioration. For the sniffer flow, it is important to get precise timestamp. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-07-22wil6210: Introduce struct for sw contextVladimir Kondratiev
Enable adding more data to the SW context. For now, add flag "mapped_as_page", to separate decisions on free-ing skb and type of DMA mapping. This allows linking skb itself to any descriptor of fragmented skb. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-07-22wil6210: Align WMI header with latest FWVladimir Kondratiev
FW guys changed header structure; align driver code Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-12wil6210: Send EAPOL frames using normal Tx queueVladimir Kondratiev
No more need for special processing of EAPOL, FW can now send EAPOL frames using normal Tx queue for TID 0 This fixes "schedule while atomic" bug - start_xmit called in softirq context; while WMI mechanism that was used may sleep. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-29wil6210: Don't use wdev->sme_stateVladimir Kondratiev
sme_state is private wdev's variable. Track connection state internally Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-22wil6210: use NAPIVladimir Kondratiev
Introduce NAPI for Rx and Tx completion. This fixes packet reordering that happens when Rx handled right in the IRQ: netif_rx puts packet in 'percpu' queue, then network stack fetches packets from 'percpu' queues for processing, with different pattern of queue switching. As result, network stack see packets in different order. This causes hard to understand TCP throughput degradation in about 30min Complete polling if only one packet was processed - this eliminates empty polls that would be otherwise done at the end of each burst Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-22wil6210: trace supportVladimir Kondratiev
Trace the following: - WMI cmd/event - log events - interrupts - Tx/Rx Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-03-13wil6210: temperature measurementVladimir Kondratiev
Firmware got support for temperature measurement. There are 2 temperature sensors: MAC and radio "not available" temperature - reported by FW as 0 or ~0 Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-03-13wil6210: sync with new firmwareVladimir Kondratiev
Adjust driver for changes in the FW API. Noticeable changes in the FW are: - temperature sensing - infrastructure for multiple connections - infrastructure for P2P - signal strength indication This commit introduces only changes that are required to support same functionality as previous firmware, no new features. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-03-13wil6210: new SW resetVladimir Kondratiev
New firmware allows for shorter SW reset procedure. After SW reset, FW raises "fw done" IRQ, at this moment mailbox control structures are initialized, driver caches it. New status bit wil_status_reset_done introduced to track completion of the reset. It is set by "fw ready" irq, and required for WMI rx flow to access control structures. WMI Tx flow protected by other status bit, wil_status_fwready. It can't be set before wil_status_reset_done is set by design. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-03-13wil6210: refactor connect_workerVladimir Kondratiev
Move wmi_connect_worker() to the main.c and change names for consistency. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-03-13wil6210: Remove local implementation of dynamic hexdumpVladimir Kondratiev
This functionality now integrated in kernel, local hack not needed any more Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-01-30wil6210: Never delete Rx chain with firmwareVladimir Kondratiev
Firmware crash on attempt to delete Rx chain. Driver part of Rx chain removed only in preparation for the target reset; as reset is the only flow that removes Rx chain in the firmware. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-01-30wil6210: fix checkpatch CamelCase warningsVladimir Kondratiev
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-01-30wil6210: Fix: Tx stallVladimir Kondratiev
Due to multi-tx-queue design, wil_start_xmit() used to be executed concurrently for different queues. Then, these transmits delivered to the same queue, creating race. As result, Tx descriptor may be skipped, causing stall in hardware. Convert to single Tx queue fixes it. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-01-30wil6210: Refactor rx init/finiVladimir Kondratiev
Move WMI related operations to wmi.c as helper functions Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-01-30wil6210: remove raw wil_dbg() callsVladimir Kondratiev
Introduce debug category "MISC", convert all raw wil_dbg() to this category. This improves dynamic debug manageability Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-01-30wil6210: Detect FW errorVladimir Kondratiev
In the firmware, added is ability to report internal errors using IRQ. Catch this IRQ and notify user space via netlink User space get notified like (udevadm monitor --kernel --property): KERNEL[12660.320520] change /devices/pci0000:00/0000:00:1c.1/0000:02:00.0/0000:03:01.0/0000:05:00.0/net/wlan12 (net) ACTION=change DEVPATH=/devices/pci0000:00/0000:00:1c.1/0000:02:00.0/0000:03:01.0/0000:05:00.0/net/wlan12 DEVTYPE=wlan EVENT=FW_ERROR IFINDEX=6 INTERFACE=wlan12 SEQNUM=2489 SOURCE=wil6210 SUBSYSTEM=net Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-01-04wireless: add new wil6210 802.11ad 60GHz driverVladimir Kondratiev
This adds support for the 60 GHz 802.11ad Wilocity card through a new driver, wil6210. Wilocity implemented the firmware, QCA maintains the device driver. Currently supported: - STA: with security - AP: limited to 1 connected STA, security disabled - Monitor: due to a hardware/firmware limitation either control or non-control frames are monitored Using a STA and AP with this drive, one can assemble a fully functional BSS. Throughput of 1.2Gbps is achieved with iperf. The wil6210 cards have on-board flash memory for the firmware, the cards comes pre-flashed and no firmware download is required. For more details see: http://wireless.kernel.org/en/users/Drivers/wil6210 Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3-18-g5258 (git 2.32.0) at 2025-08-15 12:04:12 +0000