| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds support for the 0x4004, 0x5000, and 0x5002 sensors found
on what should be the Motion R12, Fujitsu Q704, and Fujitsu T904. These
tablets use a new report ID (3) for their touch packets and a slightly
different HID descriptor format, but are otherwise largely identical in
protocol to the "MTTPC" tablets.
Note:
* The R12 uses its 0x4004 sensor for touch input only. A pen interface
is not present in its HID descriptor, though its possible a 0x4004
may be used for pen input by other tablet PCs in the future.
* The 0x5002 sensor appears to use a new report ID (8) for its pen
packets. The other sensors continue to use the traditional report
ID (2).
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The 0xEC sensor is used in multiple tablet PCs and curiously has versions
that report 256 levels of pressure (Samsung Slate 7) as well as versions
that report 1024 levels (Lenovo Thinkpad Yoga). To allow both versions to
work properly, we allow the value of HID_USAGE_PRESSURE reported to
override pressure_max.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Aaron Skomra <Aaron.Skomra@wacom.com>
Reviewed-by: Carl Worth <cworth@cworth.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
A HID Usage is a 32-bit value: an upper 16-bit "page" and a lower 16-bit
ID. While the two halves are normally reported seperately, only the
combination uniquely idenfifes a particular HID Usage.
The existing code performs the comparison in two steps, first performing a
switch on the ID and then verifying the page within each case. While this
works fine, it is very akward to handle two Usages that share a single ID,
such as HID_USAGE_PRESSURE and HID_USAGE_X because the case statement can
only have a single identifier.
To work around this, we now check the full 32-bit HID Usage directly rather
than first checking the ID and then the page. This allows the switch
statement to have distinct cases for e.g. HID_USAGE_PRESSURE and
HID_USAGE_X.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Aaron Skomra <Aaron.Skomra@wacom.com>
Reviewed-by: Carl Worth <cworth@cworth.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
New Intuos series models added a hardware switch to turn touch
data on/off. The state of the switch is reported periodically
from the tablet. To report the state the driver will emit SW_MUTE_DEVICE
events.
Reviewed_by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Synchronize with mainline to bring in the new keycode definitions and
new hwmon API.
|
|
Two tablets in this series support both pen and touch. One (Intuos S)
only supports pen. This patch also updates the driver to process wireless
devices that do not support touch interface.
Tested-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Old single touch Tablet PCs do not have touch_max set at
wacom_features. Since touch device at lease supports one
finger, assign touch_max to 1 when touch usage is defined
in its HID Descriptor and touch_max is not pre-defined.
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Merge first round of changes for 3.13 merge window.
|
|
Some multi-interface devices support expresskeys on a separate interface,
such as Bamboo; some multi-interface devices do not support touch at all,
such as Pen only Intuos5. Make sure we report the right device names.
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This will stop UPower from detecting the tablet as a power supply,
and using its battery status to hibernate or switch off the machine.
https://bugs.freedesktop.org/show_bug.cgi?id=70321
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Acked-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Adds support for the sensors integrated in to the Cintiq Companion
Hybrid. These sensors use by-and-large the same protocol as the
Cintiq 24HD touch.
NOTE: The ExpressKeys on the Cintiq Companion Hybrid are wired to
both the EMR controller and CPU GPIO pins. It may be necessary to
disable their functionality in this driver if building a custom
Android kernel for this device (lest two events be sent to userspace
for every button press).
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Fix to return a negative error code from the urb submit error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Logic sets a value and then reads it back to make sure it worked
and retries write on failures. Since read and write share a buffer,
it needs to be set back up before writing though.
Issue is not seen a lot because 1) it doesn't need to retry for
a lot of tablets and 2) a lot of failures that need a retry are
from an -ETIMEDOUT and hopefully buffer is not touched in this case.
At least one user has shown logs with buffer being modified during
-ETIMEDOUT case with linux 3.7 kernel.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This adds support for the two new multi-touch tablets.
Signed-off-by: Ping Cheng <pinglinux@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Use switch instead of if statement to verify device types
Signed-off-by: Ping Cheng <pinglinux@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Decode multitouch reports from the touch sensor of the Cintiq 24HD
touch.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Like our other pen-and-touch products, the Cintiq 24HD touch needs data
to be shared between its two sensors to facilitate proximity-based palm
rejection.
Unlike other tablets that report sensor data through separate interfaces
of the same USB device, the Cintiq 24HD touch has separate USB devices
that are connected to an internal USB hub.
This patch makes it possible to designate the USB VID/PID of the other
device so that the two may share data. To ensure we don't accidentally
link to a sensor from a physically separate device (if several have been
plugged in), we limit the search to siblings (i.e., devices directly
connected to the same hub).
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Rewrites this function to be easier to read and understand. The new
function 'wacom_set_device_mode' now handles the grunt work of
assembling the proper feature report, sending it to the device,
and ensuring the setting "sticks".
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The Cintiq 24HD touch cannot use wacom_set_phy_from_res to determine
the physical size of the touch sensor since the pen and touch are
on separate USB devices. The physical size is, however, provided in
the HID descriptor, just scaled to a unit we don't use.
This patch introduces the function wacom_fix_phy_from_hid to let
us make use of the unit and exponent data provided by HID to set
the [xy]_phy variables to an appropriate value. This function
relies on a trimmed-down version of hidinput_calc_abs_res from
the hid-input.c.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
use threaded IRQs use IRQF_ONESHOT.
|
|
|
|
Some models, such as 0xE6, report more fingers than we process.
Reported-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Tested-by: Nils Kanning <nils@kanning.de>
Tested-by: Rafi Rubin <rafi@seas.upenn.edu>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
rep_data is not an array anymore, so taking it's address when passing to
wacom_get_report() is wrong.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Tested-by: Rafi Rubin <rafi@seas.upenn.edu>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
It is replaced by BTN_TOOL_FINGER.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Tested-by: Rafi Rubin <rafi@seas.upenn.edu>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Replaces code to calculate Intuos5 physical dimensions with a call
to an existing function that performs the same task.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
This case appears to have been missed in the original commit.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Do not register battery device until connected to a tablet.
This prevents an empty battery icon from being shown when tablet is
connected using USB cable.
Also, call power_supply_powers() for apps that can make use of that
info.
And stop ignoring input registration failures.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
So we can simplify a few type related if statements
Signed-off-by: Ping Cheng <pingc@wacom.com>
Acked-by: Chris Bagwell <chris@cnpbagwell.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input layer updates from Dmitry Torokhov:
- a bunch of new drivers (DA9052/53 touchscreenn controller, Synaptics
Navpoint, LM8333 keypads, Wacom I2C touhscreen);
- updates to existing touchpad drivers (ALPS, Sntelic);
- Wacom driver now supports Intuos5;
- device-tree bindings in numerous drivers;
- other cleanups and fixes.
Fix annoying conflict in drivers/input/tablet/wacom_wac.c that I think
implies that the input layer device naming is broken, but let's see. I
brough it up with Dmitry.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (57 commits)
Input: matrix-keymap - fix building keymaps
Input: spear-keyboard - document DT bindings
Input: spear-keyboard - add device tree bindings
Input: matrix-keymap - wire up device tree support
Input: matrix-keymap - uninline and prepare for device tree support
Input: adp5588 - add support for gpio names
Input: omap-keypad - dynamically handle register offsets
Input: synaptics - fix compile warning
MAINTAINERS: adjust input-related patterns
Input: ALPS - switch to using input_mt_report_finger_count
Input: ALPS - add semi-MT support for v4 protocol
Input: Add Synaptics NavPoint (PXA27x SSP/SPI) driver
Input: atmel_mxt_ts - dump each message on just 1 line
Input: atmel_mxt_ts - do not read extra (checksum) byte
Input: atmel_mxt_ts - verify object size in mxt_write_object
Input: atmel_mxt_ts - only allow root to update firmware
Input: atmel_mxt_ts - use CONFIG_PM_SLEEP
Input: sentelic - report device's production serial number
Input: tl6040-vibra - Device Tree support
Input: evdev - properly handle read/write with count 0
...
|
|
Previously I had made the struct device point to the input device, but
after talking with Dmitry, he said that the USB device would make more
sense for this driver to point to. So converted it to use that instead.
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: Ping Cheng <pingc@wacom.com>
CC: Chris Bagwell <chris@cnpbagwell.com>
CC: Eduard Hasenleithner <eduard@hasenleithner.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Instead of returning 1 (which is not even negative) let's capture and return
error codde returned by usb_get_extra_descriptor().
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
This fixes the following warning from sparse
warning: Using plain integer as NULL pointer
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Ping Cheng <pingc@wacom.com>
Cc: Eduard Hasenleithner <eduard@hasenleithner.at>
Cc: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We should always reference the input device for dev_err(), not the USB
device. Fix up the places where I got this wrong.
Reported-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: Ping Cheng <pingc@wacom.com>
CC: Chris Bagwell <chris@cnpbagwell.com>
CC: Eduard Hasenleithner <eduard@hasenleithner.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Main part of patch is adding support for a new Wacom MT touch
packet and labels these devices using MTSCREEN type.
Other items of interest:
Delete some duplicate code in HID parsing for Y info since
its already done in X path.
In wacom_query_tablet_data(), only invoke the set report
that requests tablets to send Wacom Touch packets for
Finger interfaces. Mostly, this is to make code intent clear.
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
From the HID usage table when it is supported.
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: Ping Cheng <pingc@wacom.com>
CC: Chris Bagwell <chris@cnpbagwell.com>
CC: Eduard Hasenleithner <eduard@hasenleithner.at>
CC: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
Intuos5 tablets with PTH-* model numbers include a multitouch sensor
which use the same touch reports as the 3rd-generation Bamboo. No
useful information is in the HID descriptor for the touch interface
so hardcoded values are used during setup.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
The Touch Ring LEDs on Intuos5 tablets use a different report
format which supports only 4 levels of brightness. We remap
the 7-bit value obtained from sysfs to an appropriate value
for the tablet. Control of the crop mark LEDs (new to the I5)
is left for a later patch.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
We accidentally removed the check for NULL in 3aac0ef10b "Input: wacom -
isolate input registration".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
When a tablet connect or disconnect is detected, schedule
work queue to register or unregister related input devices.
When a wireless tablet connects, it reports same USB PID
used if tablet is connected with USB cable. Use this to
update features values, set input capabilities, and then
register device. From there, the Pen and Touch interfaces
will reuse the existing tablet's IRQ routines.
Its possible that 1 receiver is shared with 2 tablets with
different PID (small and medium Bamboo for example) so the
input is unregister at disconnect to better support this case.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
The 3rd gen Bamboo Pen & Touch and Intuos5 tablets support an
optional wireless module. When its receiver is plugged into USB,
it presents 3 interfaces: 0) Monitor 1) Pen and 2) Touch.
The exact capabilities of the Pen and Touch interfaces can
not be determined until a tablet connection is established
and reported over the Monitor interface.
This patch detects this wireless receiver and enables interrupt
packets to be processed for the Monitor interface. Processing
the data in packets will be left to another patch.
Since it doesn't make sense to create an input device for the
Monitor interface, it is not created. Creation of Pen and Touch
input device is also delayed until monitor packets can be processed.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
