| Age | Commit message (Collapse) | Author |
|---|
|
Add support for T104x board in board file t104x_qds.c, It is common for
both T1040 and T1042 as they share same QDS board.
T1040QDS board Overview
-----------------------
- SERDES Connections, 8 lanes supporting:
— PCI Express: supporting Gen 1 and Gen 2;
— SGMII
— QSGMII
— SATA 2.0
— Aurora debug with dedicated connectors (T1040 only)
- DDR Controller
- Supports rates of up to 1600 MHz data-rate
- Supports one DDR3LP UDIMM/RDIMMs, of single-, dual- or quad-rank types.
-IFC/Local Bus
- NAND flash: 8-bit, async, up to 2GB.
- NOR: 8-bit or 16-bit, non-multiplexed, up to 512MB
- GASIC: Simple (minimal) target within Qixis FPGA
- PromJET rapid memory download support
- Ethernet
- Two on-board RGMII 10/100/1G ethernet ports.
- PHY #0 remains powered up during deep-sleep (T1040 only)
- QIXIS System Logic FPGA
- Clocks
- System and DDR clock (SYSCLK, “DDRCLK”)
- SERDES clocks
- Power Supplies
- Video
- DIU supports video at up to 1280x1024x32bpp
- USB
- Supports two USB 2.0 ports with integrated PHYs
— Two type A ports with 5V@1.5A per port.
— Second port can be converted to OTG mini-AB
- SDHC
- SDHC port connects directly to an adapter card slot, featuring:
- Supporting SD slots for: SD, SDHC (1x, 4x, 8x) and/or MMC
— Supporting eMMC memory devices
- SPI
- On-board support of 3 different devices and sizes
- Other IO
- Two Serial ports
- ProfiBus port
- Four I2C ports
Add T104xQDS support in Kconfig and Makefile. Also create device tree.
Following features are currently not implmented.
- SerDes: Aurora
- IFC: GASIC, Promjet
- QIXIS
- Ethernet
- DIU
- power supplies management
- ProfiBus
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
OCA4080 overview:
- 1.466 GHz Freescale QorIQ P4080E Processor
- 4Gbyte DDR3 on board
- 8Mbyte Nor flash
- Serial RapidIO 1.2
- 1 x 10/100/1000 BASE-T front ethernet
- 1 x 1000 BASE-BX ethernet on AMC connector
Signed-off-by: Martijn de Gouw <martijn.de.gouw@prodrive.nl>
[scottwood@freescale.com: minor conflict-related changes]
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
This patch introduces the support for Keymile's kmcoge4 board which is
the internal reference design for boards based on Freescale's
P2040/P2041 SoCs. This internal reference design is named kmp204x.
The peripherals used on this board are:
- SPI NOR Flash as bootloader medium
- NAND Flash with a ubi partition
- 2 PCIe busses (hosts 1 and 3)
- 3 FMAN Ethernet devices (FMAN1 DTSEC1/2/5)
- 4 Local Bus windows, with one dedicated to the QRIO reset/power mgmt
CPLD
- 2 I2C busses
- last but not least, the mandatory serial port
The patch also adds a defconfig file for this reference design that is
necessary because of the lowmem option that must be set higher due to
the number of PCIe devices with big ioremapped mem ranges on the boad.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
If we do nothing in suspend/resume, some platform PCIe ip-block
can't guarantee the link back to L0 state from sleep, then, when
we read the EP device will hang. Only we send pme turnoff message
in pci controller suspend, and send pme exit message in resume, the
link state will be normal.
When we send pme turnoff message in pci controller suspend, the
links will into l2/l3 ready, then, host cannot communicate with
ep device, but pci-driver will call back EP device to save them
state. So we need to change platform_driver->suspend/resume to
syscore->suspend/resume.
So the new suspend/resume implementation, send pme turnoff message
in suspend, and send pme exit message in resume. And add a PME handler,
to response PME & message interrupt.
Change platform_driver->suspend/resume to syscore->suspend/resume.
pci-driver will call back EP device, to save EP state in
pci_pm_suspend_noirq, so we need to keep the link, until
pci_pm_suspend_noirq finish.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
There is QE on platform T104x, add support.
Call funcs qe_ic_init and qe_init if CONFIG_QUICC_ENGINE is defined.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
[scottwood@freesacle.com: whitespace fix]
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
This file is also used by some RDB and QDS boards. So the name seems
not so accurate. Rename it to corenet_generic.c. Also update the
function names in this file according to the change.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
|
