diff options
Diffstat (limited to 'include/net/mac80211.h')
| -rw-r--r-- | include/net/mac80211.h | 2565 |
1 files changed, 2270 insertions, 295 deletions
diff --git a/include/net/mac80211.h b/include/net/mac80211.h index eaa4affd40c..421b6ecb4b2 100644 --- a/include/net/mac80211.h +++ b/include/net/mac80211.h @@ -13,13 +13,13 @@ #ifndef MAC80211_H #define MAC80211_H +#include <linux/bug.h> #include <linux/kernel.h> #include <linux/if_ether.h> #include <linux/skbuff.h> -#include <linux/wireless.h> -#include <linux/device.h> #include <linux/ieee80211.h> #include <net/cfg80211.h> +#include <asm/unaligned.h> /** * DOC: Introduction @@ -66,10 +66,6 @@ * * Secondly, when the hardware handles fragmentation, the frame handed to * the driver from mac80211 is the MSDU, not the MPDU. - * - * Finally, for received frames, the driver is able to indicate that it has - * filled a radiotap header and put that in front of the frame; if it does - * not do so then mac80211 may add this under certain circumstances. */ /** @@ -87,15 +83,21 @@ * */ +struct device; + /** * enum ieee80211_max_queues - maximum number of queues * * @IEEE80211_MAX_QUEUES: Maximum number of regular device queues. + * @IEEE80211_MAX_QUEUE_MAP: bitmap with maximum queues set */ enum ieee80211_max_queues { - IEEE80211_MAX_QUEUES = 4, + IEEE80211_MAX_QUEUES = 16, + IEEE80211_MAX_QUEUE_MAP = BIT(IEEE80211_MAX_QUEUES) - 1, }; +#define IEEE80211_INVAL_HW_QUEUE 0xff + /** * enum ieee80211_ac_numbers - AC numbers as used in mac80211 * @IEEE80211_AC_VO: voice @@ -109,6 +111,7 @@ enum ieee80211_ac_numbers { IEEE80211_AC_BE = 2, IEEE80211_AC_BK = 3, }; +#define IEEE80211_NUM_ACS 4 /** * struct ieee80211_tx_queue_params - transmit queue configuration @@ -121,6 +124,7 @@ enum ieee80211_ac_numbers { * 2^n-1 in the range 1..32767] * @cw_max: maximum contention window [like @cw_min] * @txop: maximum burst time in units of 32 usecs, 0 meaning disabled + * @acm: is mandatory admission control required for the access category * @uapsd: is U-APSD mode enabled for the queue */ struct ieee80211_tx_queue_params { @@ -128,6 +132,7 @@ struct ieee80211_tx_queue_params { u16 cw_min; u16 cw_max; u8 aifs; + bool acm; bool uapsd; }; @@ -139,6 +144,88 @@ struct ieee80211_low_level_stats { }; /** + * enum ieee80211_chanctx_change - change flag for channel context + * @IEEE80211_CHANCTX_CHANGE_WIDTH: The channel width changed + * @IEEE80211_CHANCTX_CHANGE_RX_CHAINS: The number of RX chains changed + * @IEEE80211_CHANCTX_CHANGE_RADAR: radar detection flag changed + * @IEEE80211_CHANCTX_CHANGE_CHANNEL: switched to another operating channel, + * this is used only with channel switching with CSA + * @IEEE80211_CHANCTX_CHANGE_MIN_WIDTH: The min required channel width changed + */ +enum ieee80211_chanctx_change { + IEEE80211_CHANCTX_CHANGE_WIDTH = BIT(0), + IEEE80211_CHANCTX_CHANGE_RX_CHAINS = BIT(1), + IEEE80211_CHANCTX_CHANGE_RADAR = BIT(2), + IEEE80211_CHANCTX_CHANGE_CHANNEL = BIT(3), + IEEE80211_CHANCTX_CHANGE_MIN_WIDTH = BIT(4), +}; + +/** + * struct ieee80211_chanctx_conf - channel context that vifs may be tuned to + * + * This is the driver-visible part. The ieee80211_chanctx + * that contains it is visible in mac80211 only. + * + * @def: the channel definition + * @min_def: the minimum channel definition currently required. + * @rx_chains_static: The number of RX chains that must always be + * active on the channel to receive MIMO transmissions + * @rx_chains_dynamic: The number of RX chains that must be enabled + * after RTS/CTS handshake to receive SMPS MIMO transmissions; + * this will always be >= @rx_chains_static. + * @radar_enabled: whether radar detection is enabled on this channel. + * @drv_priv: data area for driver use, will always be aligned to + * sizeof(void *), size is determined in hw information. + */ +struct ieee80211_chanctx_conf { + struct cfg80211_chan_def def; + struct cfg80211_chan_def min_def; + + u8 rx_chains_static, rx_chains_dynamic; + + bool radar_enabled; + + u8 drv_priv[0] __aligned(sizeof(void *)); +}; + +/** + * enum ieee80211_chanctx_switch_mode - channel context switch mode + * @CHANCTX_SWMODE_REASSIGN_VIF: Both old and new contexts already + * exist (and will continue to exist), but the virtual interface + * needs to be switched from one to the other. + * @CHANCTX_SWMODE_SWAP_CONTEXTS: The old context exists but will stop + * to exist with this call, the new context doesn't exist but + * will be active after this call, the virtual interface switches + * from the old to the new (note that the driver may of course + * implement this as an on-the-fly chandef switch of the existing + * hardware context, but the mac80211 pointer for the old context + * will cease to exist and only the new one will later be used + * for changes/removal.) + */ +enum ieee80211_chanctx_switch_mode { + CHANCTX_SWMODE_REASSIGN_VIF, + CHANCTX_SWMODE_SWAP_CONTEXTS, +}; + +/** + * struct ieee80211_vif_chanctx_switch - vif chanctx switch information + * + * This is structure is used to pass information about a vif that + * needs to switch from one chanctx to another. The + * &ieee80211_chanctx_switch_mode defines how the switch should be + * done. + * + * @vif: the vif that should be switched from old_ctx to new_ctx + * @old_ctx: the old context to which the vif was assigned + * @new_ctx: the new context to which the vif must be assigned + */ +struct ieee80211_vif_chanctx_switch { + struct ieee80211_vif *vif; + struct ieee80211_chanctx_conf *old_ctx; + struct ieee80211_chanctx_conf *new_ctx; +}; + +/** * enum ieee80211_bss_change - BSS change notification flags * * These flags are used with the bss_info_changed() callback @@ -164,13 +251,24 @@ struct ieee80211_low_level_stats { * @BSS_CHANGED_QOS: QoS for this association was enabled/disabled. Note * that it is only ever disabled for station mode. * @BSS_CHANGED_IDLE: Idle changed for this BSS/interface. + * @BSS_CHANGED_SSID: SSID changed for this BSS (AP and IBSS mode) + * @BSS_CHANGED_AP_PROBE_RESP: Probe Response changed for this BSS (AP mode) + * @BSS_CHANGED_PS: PS changed for this BSS (STA mode) + * @BSS_CHANGED_TXPOWER: TX power setting changed for this interface + * @BSS_CHANGED_P2P_PS: P2P powersave settings (CTWindow, opportunistic PS) + * changed (currently only in P2P client mode, GO mode will be later) + * @BSS_CHANGED_BEACON_INFO: Data from the AP's beacon became available: + * currently dtim_period only is under consideration. + * @BSS_CHANGED_BANDWIDTH: The bandwidth used by this interface changed, + * note that this is only called when it changes after the channel + * context had been assigned. */ enum ieee80211_bss_change { BSS_CHANGED_ASSOC = 1<<0, BSS_CHANGED_ERP_CTS_PROT = 1<<1, BSS_CHANGED_ERP_PREAMBLE = 1<<2, BSS_CHANGED_ERP_SLOT = 1<<3, - BSS_CHANGED_HT = 1<<4, + BSS_CHANGED_HT = 1<<4, BSS_CHANGED_BASIC_RATES = 1<<5, BSS_CHANGED_BEACON_INT = 1<<6, BSS_CHANGED_BSSID = 1<<7, @@ -181,6 +279,13 @@ enum ieee80211_bss_change { BSS_CHANGED_ARP_FILTER = 1<<12, BSS_CHANGED_QOS = 1<<13, BSS_CHANGED_IDLE = 1<<14, + BSS_CHANGED_SSID = 1<<15, + BSS_CHANGED_AP_PROBE_RESP = 1<<16, + BSS_CHANGED_PS = 1<<17, + BSS_CHANGED_TXPOWER = 1<<18, + BSS_CHANGED_P2P_PS = 1<<19, + BSS_CHANGED_BEACON_INFO = 1<<20, + BSS_CHANGED_BANDWIDTH = 1<<21, /* when adding here, make sure to change ieee80211_reconfig */ }; @@ -193,6 +298,17 @@ enum ieee80211_bss_change { #define IEEE80211_BSS_ARP_ADDR_LIST_LEN 4 /** + * enum ieee80211_rssi_event - RSSI threshold event + * An indicator for when RSSI goes below/above a certain threshold. + * @RSSI_EVENT_HIGH: AP's rssi crossed the high threshold set by the driver. + * @RSSI_EVENT_LOW: AP's rssi crossed the low threshold set by the driver. + */ +enum ieee80211_rssi_event { + RSSI_EVENT_HIGH, + RSSI_EVENT_LOW, +}; + +/** * struct ieee80211_bss_conf - holds the BSS's changing parameters * * This structure keeps information about a BSS (and an association @@ -201,6 +317,7 @@ enum ieee80211_bss_change { * @assoc: association status * @ibss_joined: indicates whether this station is part of an IBSS * or not + * @ibss_creator: indicates if a new IBSS network is being created * @aid: association ID number, valid only when @assoc is true * @use_cts_prot: use CTS protection * @use_short_preamble: use 802.11b short preamble; @@ -210,22 +327,31 @@ enum ieee80211_bss_change { * if the hardware cannot handle this it must set the * IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE hardware flag * @dtim_period: num of beacons before the next DTIM, for beaconing, - * valid in station mode only while @assoc is true and if also - * requested by %IEEE80211_HW_NEED_DTIM_PERIOD (cf. also hw conf - * @ps_dtim_period) - * @timestamp: beacon timestamp + * valid in station mode only if after the driver was notified + * with the %BSS_CHANGED_BEACON_INFO flag, will be non-zero then. + * @sync_tsf: last beacon's/probe response's TSF timestamp (could be old + * as it may have been received during scanning long ago). If the + * HW flag %IEEE80211_HW_TIMING_BEACON_ONLY is set, then this can + * only come from a beacon, but might not become valid until after + * association when a beacon is received (which is notified with the + * %BSS_CHANGED_DTIM flag.) + * @sync_device_ts: the device timestamp corresponding to the sync_tsf, + * the driver/device can use this to calculate synchronisation + * (see @sync_tsf) + * @sync_dtim_count: Only valid when %IEEE80211_HW_TIMING_BEACON_ONLY + * is requested, see @sync_tsf/@sync_device_ts. * @beacon_int: beacon interval * @assoc_capability: capabilities taken from assoc resp * @basic_rates: bitmap of basic rates, each bit stands for an * index into the rate table configured by the driver in * the current band. + * @beacon_rate: associated AP's beacon TX rate * @mcast_rate: per-band multicast rate index + 1 (0: disabled) * @bssid: The BSSID for this BSS * @enable_beacon: whether beaconing should be enabled or not - * @channel_type: Channel type for this BSS -- the hardware might be - * configured for HT40+ while this BSS only uses no-HT, for - * example. - * @ht_operation_mode: HT operation mode (like in &struct ieee80211_ht_info). + * @chandef: Channel definition for this BSS -- the hardware might be + * configured a higher bandwidth than this BSS uses, for example. + * @ht_operation_mode: HT operation mode like in &struct ieee80211_ht_operation. * This field is only valid when the channel type is one of the HT types. * @cqm_rssi_thold: Connection quality monitor RSSI threshold, a zero value * implies disabled @@ -234,20 +360,26 @@ enum ieee80211_bss_change { * may filter ARP queries targeted for other addresses than listed here. * The driver must allow ARP queries targeted for all address listed here * to pass through. An empty list implies no ARP queries need to pass. - * @arp_addr_cnt: Number of addresses currently on the list. - * @arp_filter_enabled: Enable ARP filtering - if enabled, the hardware may - * filter ARP queries based on the @arp_addr_list, if disabled, the - * hardware must not perform any ARP filtering. Note, that the filter will - * be enabled also in promiscuous mode. + * @arp_addr_cnt: Number of addresses currently on the list. Note that this + * may be larger than %IEEE80211_BSS_ARP_ADDR_LIST_LEN (the arp_addr_list + * array size), it's up to the driver what to do in that case. * @qos: This is a QoS-enabled BSS. * @idle: This interface is idle. There's also a global idle flag in the * hardware config which may be more appropriate depending on what * your driver/device needs to do. + * @ps: power-save mode (STA only). This flag is NOT affected by + * offchannel/dynamic_ps operations. + * @ssid: The SSID of the current vif. Valid in AP and IBSS mode. + * @ssid_len: Length of SSID given in @ssid. + * @hidden_ssid: The SSID of the current vif is hidden. Only valid in AP-mode. + * @txpower: TX power in dBm + * @p2p_noa_attr: P2P NoA attribute for P2P powersave */ struct ieee80211_bss_conf { const u8 *bssid; /* association related data */ bool assoc, ibss_joined; + bool ibss_creator; u16 aid; /* erp related data */ bool use_cts_prot; @@ -257,22 +389,30 @@ struct ieee80211_bss_conf { u8 dtim_period; u16 beacon_int; u16 assoc_capability; - u64 timestamp; + u64 sync_tsf; + u32 sync_device_ts; + u8 sync_dtim_count; u32 basic_rates; + struct ieee80211_rate *beacon_rate; int mcast_rate[IEEE80211_NUM_BANDS]; u16 ht_operation_mode; s32 cqm_rssi_thold; u32 cqm_rssi_hyst; - enum nl80211_channel_type channel_type; + struct cfg80211_chan_def chandef; __be32 arp_addr_list[IEEE80211_BSS_ARP_ADDR_LIST_LEN]; - u8 arp_addr_cnt; - bool arp_filter_enabled; + int arp_addr_cnt; bool qos; bool idle; + bool ps; + u8 ssid[IEEE80211_MAX_SSID_LEN]; + size_t ssid_len; + bool hidden_ssid; + int txpower; + struct ieee80211_p2p_noa_attr p2p_noa_attr; }; /** - * enum mac80211_tx_control_flags - flags to describe transmission information/status + * enum mac80211_tx_info_flags - flags to describe transmission information/status * * These flags are used with the @flags member of &ieee80211_tx_info. * @@ -312,6 +452,9 @@ struct ieee80211_bss_conf { * @IEEE80211_TX_CTL_RATE_CTRL_PROBE: internal to mac80211, can be * set by rate control algorithms to indicate probe rate, will * be cleared for fragmented frames (except on the last fragment) + * @IEEE80211_TX_INTFL_OFFCHAN_TX_OK: Internal to mac80211. Used to indicate + * that a frame can be transmitted while the queues are stopped for + * off-channel operation. * @IEEE80211_TX_INTFL_NEED_TXPROCESSING: completely internal to mac80211, * used to indicate that a pending frame requires TX processing before * it can be sent out. @@ -319,9 +462,9 @@ struct ieee80211_bss_conf { * used to indicate that a frame was already retried due to PS * @IEEE80211_TX_INTFL_DONT_ENCRYPT: completely internal to mac80211, * used to indicate frame should not be encrypted - * @IEEE80211_TX_CTL_PSPOLL_RESPONSE: (internal?) - * This frame is a response to a PS-poll frame and should be sent - * although the station is in powersave mode. + * @IEEE80211_TX_CTL_NO_PS_BUFFER: This frame is a response to a poll + * frame (PS-Poll or uAPSD) or a non-bufferable MMPDU and must + * be sent although the station is in powersave mode. * @IEEE80211_TX_CTL_MORE_FRAMES: More frames will be passed to the * transmit function after the current frame, this can be used * by drivers to kick the DMA queue only if unset or when the @@ -329,19 +472,43 @@ struct ieee80211_bss_conf { * @IEEE80211_TX_INTFL_RETRANSMISSION: This frame is being retransmitted * after TX status because the destination was asleep, it must not * be modified again (no seqno assignment, crypto, etc.) - * @IEEE80211_TX_INTFL_HAS_RADIOTAP: This frame was injected and still - * has a radiotap header at skb->data. + * @IEEE80211_TX_INTFL_MLME_CONN_TX: This frame was transmitted by the MLME + * code for connection establishment, this indicates that its status + * should kick the MLME state machine. * @IEEE80211_TX_INTFL_NL80211_FRAME_TX: Frame was requested through nl80211 * MLME command (internal to mac80211 to figure out whether to send TX * status to user space) * @IEEE80211_TX_CTL_LDPC: tells the driver to use LDPC for this frame * @IEEE80211_TX_CTL_STBC: Enables Space-Time Block Coding (STBC) for this * frame and selects the maximum number of streams that it can use. + * @IEEE80211_TX_CTL_TX_OFFCHAN: Marks this packet to be transmitted on + * the off-channel channel when a remain-on-channel offload is done + * in hardware -- normal packets still flow and are expected to be + * handled properly by the device. + * @IEEE80211_TX_INTFL_TKIP_MIC_FAILURE: Marks this packet to be used for TKIP + * testing. It will be sent out with incorrect Michael MIC key to allow + * TKIP countermeasures to be tested. + * @IEEE80211_TX_CTL_NO_CCK_RATE: This frame will be sent at non CCK rate. + * This flag is actually used for management frame especially for P2P + * frames not being sent at CCK rate in 2GHz band. + * @IEEE80211_TX_STATUS_EOSP: This packet marks the end of service period, + * when its status is reported the service period ends. For frames in + * an SP that mac80211 transmits, it is already set; for driver frames + * the driver may set this flag. It is also used to do the same for + * PS-Poll responses. + * @IEEE80211_TX_CTL_USE_MINRATE: This frame will be sent at lowest rate. + * This flag is used to send nullfunc frame at minimum rate when + * the nullfunc is used for connection monitoring purpose. + * @IEEE80211_TX_CTL_DONTFRAG: Don't fragment this packet even if it + * would be fragmented by size (this is optional, only used for + * monitor injection). + * @IEEE80211_TX_CTL_PS_RESPONSE: This frame is a response to a poll + * frame (PS-Poll or uAPSD). * * Note: If you have to add new flags to the enumeration, then don't * forget to update %IEEE80211_TX_TEMPORARY_FLAGS when necessary. */ -enum mac80211_tx_control_flags { +enum mac80211_tx_info_flags { IEEE80211_TX_CTL_REQ_TX_STATUS = BIT(0), IEEE80211_TX_CTL_ASSIGN_SEQ = BIT(1), IEEE80211_TX_CTL_NO_ACK = BIT(2), @@ -355,20 +522,40 @@ enum mac80211_tx_control_flags { IEEE80211_TX_STAT_AMPDU = BIT(10), IEEE80211_TX_STAT_AMPDU_NO_BACK = BIT(11), IEEE80211_TX_CTL_RATE_CTRL_PROBE = BIT(12), + IEEE80211_TX_INTFL_OFFCHAN_TX_OK = BIT(13), IEEE80211_TX_INTFL_NEED_TXPROCESSING = BIT(14), IEEE80211_TX_INTFL_RETRIED = BIT(15), IEEE80211_TX_INTFL_DONT_ENCRYPT = BIT(16), - IEEE80211_TX_CTL_PSPOLL_RESPONSE = BIT(17), + IEEE80211_TX_CTL_NO_PS_BUFFER = BIT(17), IEEE80211_TX_CTL_MORE_FRAMES = BIT(18), IEEE80211_TX_INTFL_RETRANSMISSION = BIT(19), - IEEE80211_TX_INTFL_HAS_RADIOTAP = BIT(20), + IEEE80211_TX_INTFL_MLME_CONN_TX = BIT(20), IEEE80211_TX_INTFL_NL80211_FRAME_TX = BIT(21), IEEE80211_TX_CTL_LDPC = BIT(22), IEEE80211_TX_CTL_STBC = BIT(23) | BIT(24), + IEEE80211_TX_CTL_TX_OFFCHAN = BIT(25), + IEEE80211_TX_INTFL_TKIP_MIC_FAILURE = BIT(26), + IEEE80211_TX_CTL_NO_CCK_RATE = BIT(27), + IEEE80211_TX_STATUS_EOSP = BIT(28), + IEEE80211_TX_CTL_USE_MINRATE = BIT(29), + IEEE80211_TX_CTL_DONTFRAG = BIT(30), + IEEE80211_TX_CTL_PS_RESPONSE = BIT(31), }; #define IEEE80211_TX_CTL_STBC_SHIFT 23 +/** + * enum mac80211_tx_control_flags - flags to describe transmit control + * + * @IEEE80211_TX_CTRL_PORT_CTRL_PROTO: this frame is a port control + * protocol frame (e.g. EAP) + * + * These flags are used in tx_info->control.flags. + */ +enum mac80211_tx_control_flags { + IEEE80211_TX_CTRL_PORT_CTRL_PROTO = BIT(0), +}; + /* * This definition is used as a mask to clear all temporary flags, which are * set by the tx handlers for each transmission attempt by the mac80211 stack. @@ -378,9 +565,9 @@ enum mac80211_tx_control_flags { IEEE80211_TX_CTL_SEND_AFTER_DTIM | IEEE80211_TX_CTL_AMPDU | \ IEEE80211_TX_STAT_TX_FILTERED | IEEE80211_TX_STAT_ACK | \ IEEE80211_TX_STAT_AMPDU | IEEE80211_TX_STAT_AMPDU_NO_BACK | \ - IEEE80211_TX_CTL_RATE_CTRL_PROBE | IEEE80211_TX_CTL_PSPOLL_RESPONSE | \ + IEEE80211_TX_CTL_RATE_CTRL_PROBE | IEEE80211_TX_CTL_NO_PS_BUFFER | \ IEEE80211_TX_CTL_MORE_FRAMES | IEEE80211_TX_CTL_LDPC | \ - IEEE80211_TX_CTL_STBC) + IEEE80211_TX_CTL_STBC | IEEE80211_TX_STATUS_EOSP) /** * enum mac80211_rate_control_flags - per-rate flags set by the @@ -394,9 +581,14 @@ enum mac80211_tx_control_flags { * This is set if the current BSS requires ERP protection. * @IEEE80211_TX_RC_USE_SHORT_PREAMBLE: Use short preamble. * @IEEE80211_TX_RC_MCS: HT rate. + * @IEEE80211_TX_RC_VHT_MCS: VHT MCS rate, in this case the idx field is split + * into a higher 4 bits (Nss) and lower 4 bits (MCS number) * @IEEE80211_TX_RC_GREEN_FIELD: Indicates whether this rate should be used in * Greenfield mode. * @IEEE80211_TX_RC_40_MHZ_WIDTH: Indicates if the Channel Width should be 40 MHz. + * @IEEE80211_TX_RC_80_MHZ_WIDTH: Indicates 80 MHz transmission + * @IEEE80211_TX_RC_160_MHZ_WIDTH: Indicates 160 MHz transmission + * (80+80 isn't supported yet) * @IEEE80211_TX_RC_DUP_DATA: The frame should be transmitted on both of the * adjacent 20 MHz channels, if the current channel type is * NL80211_CHAN_HT40MINUS or NL80211_CHAN_HT40PLUS. @@ -407,12 +599,15 @@ enum mac80211_rate_control_flags { IEEE80211_TX_RC_USE_CTS_PROTECT = BIT(1), IEEE80211_TX_RC_USE_SHORT_PREAMBLE = BIT(2), - /* rate index is an MCS rate number instead of an index */ + /* rate index is an HT/VHT MCS instead of an index */ IEEE80211_TX_RC_MCS = BIT(3), IEEE80211_TX_RC_GREEN_FIELD = BIT(4), IEEE80211_TX_RC_40_MHZ_WIDTH = BIT(5), IEEE80211_TX_RC_DUP_DATA = BIT(6), IEEE80211_TX_RC_SHORT_GI = BIT(7), + IEEE80211_TX_RC_VHT_MCS = BIT(8), + IEEE80211_TX_RC_80_MHZ_WIDTH = BIT(9), + IEEE80211_TX_RC_160_MHZ_WIDTH = BIT(10), }; @@ -423,7 +618,10 @@ enum mac80211_rate_control_flags { #define IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE 24 /* maximum number of rate stages */ -#define IEEE80211_TX_MAX_RATES 5 +#define IEEE80211_TX_MAX_RATES 4 + +/* maximum number of rate table entries */ +#define IEEE80211_TX_RATE_TABLE_SIZE 4 /** * struct ieee80211_tx_rate - rate selection/status @@ -455,10 +653,32 @@ enum mac80211_rate_control_flags { */ struct ieee80211_tx_rate { s8 idx; - u8 count; - u8 flags; + u16 count:5, + flags:11; } __packed; +#define IEEE80211_MAX_TX_RETRY 31 + +static inline void ieee80211_rate_set_vht(struct ieee80211_tx_rate *rate, + u8 mcs, u8 nss) +{ + WARN_ON(mcs & ~0xF); + WARN_ON((nss - 1) & ~0x7); + rate->idx = ((nss - 1) << 4) | mcs; +} + +static inline u8 +ieee80211_rate_get_vht_mcs(const struct ieee80211_tx_rate *rate) +{ + return rate->idx & 0xF; +} + +static inline u8 +ieee80211_rate_get_vht_nss(const struct ieee80211_tx_rate *rate) +{ + return (rate->idx >> 4) + 1; +} + /** * struct ieee80211_tx_info - skb transmit information * @@ -467,13 +687,10 @@ struct ieee80211_tx_rate { * (2) driver internal use (if applicable) * (3) TX status information - driver tells mac80211 what happened * - * The TX control's sta pointer is only valid during the ->tx call, - * it may be NULL. - * * @flags: transmit info flags, defined above * @band: the band to transmit on (use for checking for races) - * @antenna_sel_tx: antenna to use, 0 for automatic diversity - * @pad: padding, ignore + * @hw_queue: HW queue to put the frame on, skb_get_queue_mapping() gives the AC + * @ack_frame_id: internal frame ID for TX status, used internally * @control: union for control data * @status: union for status data * @driver_data: array of driver_data pointers @@ -488,10 +705,9 @@ struct ieee80211_tx_info { u32 flags; u8 band; - u8 antenna_sel_tx; + u8 hw_queue; - /* 2 byte hole */ - u8 pad[2]; + u16 ack_frame_id; union { struct { @@ -501,6 +717,11 @@ struct ieee80211_tx_info { struct ieee80211_tx_rate rates[ IEEE80211_TX_MAX_RATES]; s8 rts_cts_rate_idx; + u8 use_rts:1; + u8 use_cts_prot:1; + u8 short_preamble:1; + u8 skip_table:1; + /* 2 bytes free */ }; /* only needed before rate control */ unsigned long jiffies; @@ -508,18 +729,22 @@ struct ieee80211_tx_info { /* NB: vif can be NULL for injected frames */ struct ieee80211_vif *vif; struct ieee80211_key_conf *hw_key; - struct ieee80211_sta *sta; + u32 flags; + /* 4 bytes free */ } control; struct { struct ieee80211_tx_rate rates[IEEE80211_TX_MAX_RATES]; + s32 ack_signal; u8 ampdu_ack_len; - int ack_signal; u8 ampdu_len; - /* 15 bytes free */ + u8 antenna; + void *status_driver_data[21 / sizeof(void *)]; } status; struct { struct ieee80211_tx_rate driver_rates[ IEEE80211_TX_MAX_RATES]; + u8 pad[4]; + void *rate_driver_data[ IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE / sizeof(void *)]; }; @@ -528,6 +753,21 @@ struct ieee80211_tx_info { }; }; +/** + * struct ieee80211_sched_scan_ies - scheduled scan IEs + * + * This structure is used to pass the appropriate IEs to be used in scheduled + * scans for all bands. It contains both the IEs passed from the userspace + * and the ones generated by mac80211. + * + * @ie: array with the IEs for each supported band + * @len: array with the total length of the IEs for each band + */ +struct ieee80211_sched_scan_ies { + u8 *ie[IEEE80211_NUM_BANDS]; + size_t len[IEEE80211_NUM_BANDS]; +}; + static inline struct ieee80211_tx_info *IEEE80211_SKB_CB(struct sk_buff *skb) { return (struct ieee80211_tx_info *)skb->cb; @@ -567,7 +807,7 @@ ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info) info->status.rates[i].count = 0; BUILD_BUG_ON( - offsetof(struct ieee80211_tx_info, status.ampdu_ack_len) != 23); + offsetof(struct ieee80211_tx_info, status.ack_signal) != 20); memset(&info->status.ampdu_ack_len, 0, sizeof(struct ieee80211_tx_info) - offsetof(struct ieee80211_tx_info, status.ampdu_ack_len)); @@ -590,26 +830,97 @@ ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info) * the frame. * @RX_FLAG_FAILED_PLCP_CRC: Set this flag if the PCLP check failed on * the frame. - * @RX_FLAG_TSFT: The timestamp passed in the RX status (@mactime field) - * is valid. This is useful in monitor mode and necessary for beacon frames - * to enable IBSS merging. + * @RX_FLAG_MACTIME_START: The timestamp passed in the RX status (@mactime + * field) is valid and contains the time the first symbol of the MPDU + * was received. This is useful in monitor mode and for proper IBSS + * merging. + * @RX_FLAG_MACTIME_END: The timestamp passed in the RX status (@mactime + * field) is valid and contains the time the last symbol of the MPDU + * (including FCS) was received. * @RX_FLAG_SHORTPRE: Short preamble was used for this frame * @RX_FLAG_HT: HT MCS was used and rate_idx is MCS index + * @RX_FLAG_VHT: VHT MCS was used and rate_index is MCS index * @RX_FLAG_40MHZ: HT40 (40 MHz) was used * @RX_FLAG_SHORT_GI: Short guard interval was used + * @RX_FLAG_NO_SIGNAL_VAL: The signal strength value is not present. + * Valid only for data frames (mainly A-MPDU) + * @RX_FLAG_HT_GF: This frame was received in a HT-greenfield transmission, if + * the driver fills this value it should add %IEEE80211_RADIOTAP_MCS_HAVE_FMT + * to hw.radiotap_mcs_details to advertise that fact + * @RX_FLAG_AMPDU_DETAILS: A-MPDU details are known, in particular the reference + * number (@ampdu_reference) must be populated and be a distinct number for + * each A-MPDU + * @RX_FLAG_AMPDU_REPORT_ZEROLEN: driver reports 0-length subframes + * @RX_FLAG_AMPDU_IS_ZEROLEN: This is a zero-length subframe, for + * monitoring purposes only + * @RX_FLAG_AMPDU_LAST_KNOWN: last subframe is known, should be set on all + * subframes of a single A-MPDU + * @RX_FLAG_AMPDU_IS_LAST: this subframe is the last subframe of the A-MPDU + * @RX_FLAG_AMPDU_DELIM_CRC_ERROR: A delimiter CRC error has been detected + * on this subframe + * @RX_FLAG_AMPDU_DELIM_CRC_KNOWN: The delimiter CRC field is known (the CRC + * is stored in the @ampdu_delimiter_crc field) + * @RX_FLAG_LDPC: LDPC was used + * @RX_FLAG_STBC_MASK: STBC 2 bit bitmask. 1 - Nss=1, 2 - Nss=2, 3 - Nss=3 + * @RX_FLAG_10MHZ: 10 MHz (half channel) was used + * @RX_FLAG_5MHZ: 5 MHz (quarter channel) was used + * @RX_FLAG_AMSDU_MORE: Some drivers may prefer to report separate A-MSDU + * subframes instead of a one huge frame for performance reasons. + * All, but the last MSDU from an A-MSDU should have this flag set. E.g. + * if an A-MSDU has 3 frames, the first 2 must have the flag set, while + * the 3rd (last) one must not have this flag set. The flag is used to + * deal with retransmission/duplication recovery properly since A-MSDU + * subframes share the same sequence number. Reported subframes can be + * either regular MSDU or singly A-MSDUs. Subframes must not be + * interleaved with other frames. */ enum mac80211_rx_flags { - RX_FLAG_MMIC_ERROR = 1<<0, - RX_FLAG_DECRYPTED = 1<<1, - RX_FLAG_MMIC_STRIPPED = 1<<3, - RX_FLAG_IV_STRIPPED = 1<<4, - RX_FLAG_FAILED_FCS_CRC = 1<<5, - RX_FLAG_FAILED_PLCP_CRC = 1<<6, - RX_FLAG_TSFT = 1<<7, - RX_FLAG_SHORTPRE = 1<<8, - RX_FLAG_HT = 1<<9, - RX_FLAG_40MHZ = 1<<10, - RX_FLAG_SHORT_GI = 1<<11, + RX_FLAG_MMIC_ERROR = BIT(0), + RX_FLAG_DECRYPTED = BIT(1), + RX_FLAG_MMIC_STRIPPED = BIT(3), + RX_FLAG_IV_STRIPPED = BIT(4), + RX_FLAG_FAILED_FCS_CRC = BIT(5), + RX_FLAG_FAILED_PLCP_CRC = BIT(6), + RX_FLAG_MACTIME_START = BIT(7), + RX_FLAG_SHORTPRE = BIT(8), + RX_FLAG_HT = BIT(9), + RX_FLAG_40MHZ = BIT(10), + RX_FLAG_SHORT_GI = BIT(11), + RX_FLAG_NO_SIGNAL_VAL = BIT(12), + RX_FLAG_HT_GF = BIT(13), + RX_FLAG_AMPDU_DETAILS = BIT(14), + RX_FLAG_AMPDU_REPORT_ZEROLEN = BIT(15), + RX_FLAG_AMPDU_IS_ZEROLEN = BIT(16), + RX_FLAG_AMPDU_LAST_KNOWN = BIT(17), + RX_FLAG_AMPDU_IS_LAST = BIT(18), + RX_FLAG_AMPDU_DELIM_CRC_ERROR = BIT(19), + RX_FLAG_AMPDU_DELIM_CRC_KNOWN = BIT(20), + RX_FLAG_MACTIME_END = BIT(21), + RX_FLAG_VHT = BIT(22), + RX_FLAG_LDPC = BIT(23), + RX_FLAG_STBC_MASK = BIT(26) | BIT(27), + RX_FLAG_10MHZ = BIT(28), + RX_FLAG_5MHZ = BIT(29), + RX_FLAG_AMSDU_MORE = BIT(30), +}; + +#define RX_FLAG_STBC_SHIFT 26 + +/** + * enum mac80211_rx_vht_flags - receive VHT flags + * + * These flags are used with the @vht_flag member of + * &struct ieee80211_rx_status. + * @RX_VHT_FLAG_80MHZ: 80 MHz was used + * @RX_VHT_FLAG_80P80MHZ: 80+80 MHz was used + * @RX_VHT_FLAG_160MHZ: 160 MHz was used + * @RX_VHT_FLAG_BF: packet was beamformed + */ +enum mac80211_rx_vht_flags { + RX_VHT_FLAG_80MHZ = BIT(0), + RX_VHT_FLAG_80P80MHZ = BIT(1), + RX_VHT_FLAG_160MHZ = BIT(2), + RX_VHT_FLAG_BF = BIT(3), }; /** @@ -621,26 +932,44 @@ enum mac80211_rx_flags { * * @mactime: value in microseconds of the 64-bit Time Synchronization Function * (TSF) timer when the first data symbol (MPDU) arrived at the hardware. + * @device_timestamp: arbitrary timestamp for the device, mac80211 doesn't use + * it but can store it and pass it back to the driver for synchronisation * @band: the active band when this frame was received * @freq: frequency the radio was tuned to when receiving this frame, in MHz * @signal: signal strength when receiving this frame, either in dBm, in dB or * unspecified depending on the hardware capabilities flags * @IEEE80211_HW_SIGNAL_* + * @chains: bitmask of receive chains for which separate signal strength + * values were filled. + * @chain_signal: per-chain signal strength, in dBm (unlike @signal, doesn't + * support dB or unspecified units) * @antenna: antenna used * @rate_idx: index of data rate into band's supported rates or MCS index if - * HT rates are use (RX_FLAG_HT) + * HT or VHT is used (%RX_FLAG_HT/%RX_FLAG_VHT) + * @vht_nss: number of streams (VHT only) * @flag: %RX_FLAG_* + * @vht_flag: %RX_VHT_FLAG_* * @rx_flags: internal RX flags for mac80211 + * @ampdu_reference: A-MPDU reference number, must be a different value for + * each A-MPDU but the same for each subframe within one A-MPDU + * @ampdu_delimiter_crc: A-MPDU delimiter CRC */ struct ieee80211_rx_status { u64 mactime; - enum ieee80211_band band; - int freq; - int signal; - int antenna; - int rate_idx; - int flag; - unsigned int rx_flags; + u32 device_timestamp; + u32 ampdu_reference; + u32 flag; + u16 freq; + u8 vht_flag; + u8 rate_idx; + u8 vht_nss; + u8 rx_flags; + u8 band; + u8 antenna; + s8 signal; + u8 chains; + s8 chain_signal[IEEE80211_MAX_CHAINS]; + u8 ampdu_delimiter_crc; }; /** @@ -685,6 +1014,8 @@ enum ieee80211_conf_flags { * @IEEE80211_CONF_CHANGE_RETRY_LIMITS: retry limits changed * @IEEE80211_CONF_CHANGE_IDLE: Idle flag changed * @IEEE80211_CONF_CHANGE_SMPS: Spatial multiplexing powersave mode changed + * Note that this is only valid if channel contexts are not used, + * otherwise each channel context has the number of chains listed. */ enum ieee80211_conf_changed { IEEE80211_CONF_CHANGE_SMPS = BIT(1), @@ -736,21 +1067,24 @@ enum ieee80211_smps_mode { * powersave documentation below. This variable is valid only when * the CONF_PS flag is set. * - * @power_level: requested transmit power (in dBm) + * @power_level: requested transmit power (in dBm), backward compatibility + * value only that is set to the minimum of all interfaces * - * @channel: the channel to tune to - * @channel_type: the channel (HT) type + * @chandef: the channel definition to tune to + * @radar_enabled: whether radar detection is enabled * * @long_frame_max_tx_count: Maximum number of transmissions for a "long" frame - * (a frame not RTS protected), called "dot11LongRetryLimit" in 802.11, - * but actually means the number of transmissions not the number of retries + * (a frame not RTS protected), called "dot11LongRetryLimit" in 802.11, + * but actually means the number of transmissions not the number of retries * @short_frame_max_tx_count: Maximum number of transmissions for a "short" - * frame, called "dot11ShortRetryLimit" in 802.11, but actually means the - * number of transmissions not the number of retries + * frame, called "dot11ShortRetryLimit" in 802.11, but actually means the + * number of transmissions not the number of retries * * @smps_mode: spatial multiplexing powersave mode; note that * %IEEE80211_SMPS_STATIC is used when the device is not - * configured for an HT channel + * configured for an HT channel. + * Note that this is only valid if channel contexts are not used, + * otherwise each channel context has the number of chains listed. */ struct ieee80211_conf { u32 flags; @@ -762,8 +1096,8 @@ struct ieee80211_conf { u8 long_frame_max_tx_count, short_frame_max_tx_count; - struct ieee80211_channel *channel; - enum nl80211_channel_type channel_type; + struct cfg80211_chan_def chandef; + bool radar_enabled; enum ieee80211_smps_mode smps_mode; }; @@ -779,17 +1113,32 @@ struct ieee80211_conf { * the driver passed into mac80211. * @block_tx: Indicates whether transmission must be blocked before the * scheduled channel switch, as indicated by the AP. - * @channel: the new channel to switch to + * @chandef: the new channel to switch to * @count: the number of TBTT's until the channel switch event */ struct ieee80211_channel_switch { u64 timestamp; bool block_tx; - struct ieee80211_channel *channel; + struct cfg80211_chan_def chandef; u8 count; }; /** + * enum ieee80211_vif_flags - virtual interface flags + * + * @IEEE80211_VIF_BEACON_FILTER: the device performs beacon filtering + * on this virtual interface to avoid unnecessary CPU wakeups + * @IEEE80211_VIF_SUPPORTS_CQM_RSSI: the device can do connection quality + * monitoring on this virtual interface -- i.e. it can monitor + * connection quality related parameters, such as the RSSI level and + * provide notifications if configured trigger levels are reached. + */ +enum ieee80211_vif_flags { + IEEE80211_VIF_BEACON_FILTER = BIT(0), + IEEE80211_VIF_SUPPORTS_CQM_RSSI = BIT(1), +}; + +/** * struct ieee80211_vif - per-interface data * * Data in this structure is continually present for driver @@ -801,6 +1150,23 @@ struct ieee80211_channel_switch { * @addr: address of this interface * @p2p: indicates whether this AP or STA interface is a p2p * interface, i.e. a GO or p2p-sta respectively + * @csa_active: marks whether a channel switch is going on. Internally it is + * write-protected by sdata_lock and local->mtx so holding either is fine + * for read access. + * @driver_flags: flags/capabilities the driver has for this interface, + * these need to be set (or cleared) when the interface is added + * or, if supported by the driver, the interface type is changed + * at runtime, mac80211 will never touch this field + * @hw_queue: hardware queue for each AC + * @cab_queue: content-after-beacon (DTIM beacon really) queue, AP mode only + * @chanctx_conf: The channel context this interface is assigned to, or %NULL + * when it is not assigned. This pointer is RCU-protected due to the TX + * path needing to access it; even though the netdev carrier will always + * be off when it is %NULL there can still be races and packets could be + * processed after it switches back to %NULL. + * @debugfs_dir: debugfs dentry, can be used by drivers to create own per + * interface debug files. Note that it will be NULL for the virtual + * monitor interface (if that is requested.) * @drv_priv: data area for driver use, will always be aligned to * sizeof(void *). */ @@ -809,8 +1175,21 @@ struct ieee80211_vif { struct ieee80211_bss_conf bss_conf; u8 addr[ETH_ALEN]; bool p2p; + bool csa_active; + + u8 cab_queue; + u8 hw_queue[IEEE80211_NUM_ACS]; + + struct ieee80211_chanctx_conf __rcu *chanctx_conf; + + u32 driver_flags; + +#ifdef CONFIG_MAC80211_DEBUGFS + struct dentry *debugfs_dir; +#endif + /* must be last */ - u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *)))); + u8 drv_priv[0] __aligned(sizeof(void *)); }; static inline bool ieee80211_vif_is_mesh(struct ieee80211_vif *vif) @@ -822,13 +1201,24 @@ static inline bool ieee80211_vif_is_mesh(struct ieee80211_vif *vif) } /** + * wdev_to_ieee80211_vif - return a vif struct from a wdev + * @wdev: the wdev to get the vif for + * + * This can be used by mac80211 drivers with direct cfg80211 APIs + * (like the vendor commands) that get a wdev. + * + * Note that this function may return %NULL if the given wdev isn't + * associated with a vif that the driver knows about (e.g. monitor + * or AP_VLAN interfaces.) + */ +struct ieee80211_vif *wdev_to_ieee80211_vif(struct wireless_dev *wdev); + +/** * enum ieee80211_key_flags - key flags * * These flags are used for communication about keys between the driver * and mac80211, with the @flags parameter of &struct ieee80211_key_conf. * - * @IEEE80211_KEY_FLAG_WMM_STA: Set by mac80211, this flag indicates - * that the STA this key will be used with could be using QoS. * @IEEE80211_KEY_FLAG_GENERATE_IV: This flag should be set by the * driver to indicate that it requires IV generation for this * particular key. @@ -837,16 +1227,32 @@ static inline bool ieee80211_vif_is_mesh(struct ieee80211_vif *vif) * generation in software. * @IEEE80211_KEY_FLAG_PAIRWISE: Set by mac80211, this flag indicates * that the key is pairwise rather then a shared key. - * @IEEE80211_KEY_FLAG_SW_MGMT: This flag should be set by the driver for a + * @IEEE80211_KEY_FLAG_SW_MGMT_TX: This flag should be set by the driver for a * CCMP key if it requires CCMP encryption of management frames (MFP) to * be done in software. + * @IEEE80211_KEY_FLAG_PUT_IV_SPACE: This flag should be set by the driver + * if space should be prepared for the IV, but the IV + * itself should not be generated. Do not set together with + * @IEEE80211_KEY_FLAG_GENERATE_IV on the same key. + * @IEEE80211_KEY_FLAG_RX_MGMT: This key will be used to decrypt received + * management frames. The flag can help drivers that have a hardware + * crypto implementation that doesn't deal with management frames + * properly by allowing them to not upload the keys to hardware and + * fall back to software crypto. Note that this flag deals only with + * RX, if your crypto engine can't deal with TX you can also set the + * %IEEE80211_KEY_FLAG_SW_MGMT_TX flag to encrypt such frames in SW. + * @IEEE80211_KEY_FLAG_GENERATE_IV_MGMT: This flag should be set by the + * driver for a CCMP key to indicate that is requires IV generation + * only for managment frames (MFP). */ enum ieee80211_key_flags { - IEEE80211_KEY_FLAG_WMM_STA = 1<<0, - IEEE80211_KEY_FLAG_GENERATE_IV = 1<<1, - IEEE80211_KEY_FLAG_GENERATE_MMIC= 1<<2, - IEEE80211_KEY_FLAG_PAIRWISE = 1<<3, - IEEE80211_KEY_FLAG_SW_MGMT = 1<<4, + IEEE80211_KEY_FLAG_GENERATE_IV_MGMT = BIT(0), + IEEE80211_KEY_FLAG_GENERATE_IV = BIT(1), + IEEE80211_KEY_FLAG_GENERATE_MMIC = BIT(2), + IEEE80211_KEY_FLAG_PAIRWISE = BIT(3), + IEEE80211_KEY_FLAG_SW_MGMT_TX = BIT(4), + IEEE80211_KEY_FLAG_PUT_IV_SPACE = BIT(5), + IEEE80211_KEY_FLAG_RX_MGMT = BIT(6), }; /** @@ -882,6 +1288,36 @@ struct ieee80211_key_conf { }; /** + * struct ieee80211_cipher_scheme - cipher scheme + * + * This structure contains a cipher scheme information defining + * the secure packet crypto handling. + * + * @cipher: a cipher suite selector + * @iftype: a cipher iftype bit mask indicating an allowed cipher usage + * @hdr_len: a length of a security header used the cipher + * @pn_len: a length of a packet number in the security header + * @pn_off: an offset of pn from the beginning of the security header + * @key_idx_off: an offset of key index byte in the security header + * @key_idx_mask: a bit mask of key_idx bits + * @key_idx_shift: a bit shift needed to get key_idx + * key_idx value calculation: + * (sec_header_base[key_idx_off] & key_idx_mask) >> key_idx_shift + * @mic_len: a mic length in bytes + */ +struct ieee80211_cipher_scheme { + u32 cipher; + u16 iftype; + u8 hdr_len; + u8 pn_len; + u8 pn_off; + u8 key_idx_off; + u8 key_idx_mask; + u8 key_idx_shift; + u8 mic_len; +}; + +/** * enum set_key_cmd - key command * * Used with the set_key() callback in &struct ieee80211_ops, this @@ -895,6 +1331,61 @@ enum set_key_cmd { }; /** + * enum ieee80211_sta_state - station state + * + * @IEEE80211_STA_NOTEXIST: station doesn't exist at all, + * this is a special state for add/remove transitions + * @IEEE80211_STA_NONE: station exists without special state + * @IEEE80211_STA_AUTH: station is authenticated + * @IEEE80211_STA_ASSOC: station is associated + * @IEEE80211_STA_AUTHORIZED: station is authorized (802.1X) + */ +enum ieee80211_sta_state { + /* NOTE: These need to be ordered correctly! */ + IEEE80211_STA_NOTEXIST, + IEEE80211_STA_NONE, + IEEE80211_STA_AUTH, + IEEE80211_STA_ASSOC, + IEEE80211_STA_AUTHORIZED, +}; + +/** + * enum ieee80211_sta_rx_bandwidth - station RX bandwidth + * @IEEE80211_STA_RX_BW_20: station can only receive 20 MHz + * @IEEE80211_STA_RX_BW_40: station can receive up to 40 MHz + * @IEEE80211_STA_RX_BW_80: station can receive up to 80 MHz + * @IEEE80211_STA_RX_BW_160: station can receive up to 160 MHz + * (including 80+80 MHz) + * + * Implementation note: 20 must be zero to be initialized + * correctly, the values must be sorted. + */ +enum ieee80211_sta_rx_bandwidth { + IEEE80211_STA_RX_BW_20 = 0, + IEEE80211_STA_RX_BW_40, + IEEE80211_STA_RX_BW_80, + IEEE80211_STA_RX_BW_160, +}; + +/** + * struct ieee80211_sta_rates - station rate selection table + * + * @rcu_head: RCU head used for freeing the table on update + * @rate: transmit rates/flags to be used by default. + * Overriding entries per-packet is possible by using cb tx control. + */ +struct ieee80211_sta_rates { + struct rcu_head rcu_head; + struct { + s8 idx; + u8 count; + u8 count_cts; + u8 count_rts; + u16 flags; + } rate[IEEE80211_TX_RATE_TABLE_SIZE]; +}; + +/** * struct ieee80211_sta - station table entry * * A station table entry represents a station we are possibly @@ -907,18 +1398,40 @@ enum set_key_cmd { * @addr: MAC address * @aid: AID we assigned to the station if we're an AP * @supp_rates: Bitmap of supported rates (per band) - * @ht_cap: HT capabilities of this STA; restricted to our own TX capabilities + * @ht_cap: HT capabilities of this STA; restricted to our own capabilities + * @vht_cap: VHT capabilities of this STA; restricted to our own capabilities + * @wme: indicates whether the STA supports WME. Only valid during AP-mode. * @drv_priv: data area for driver use, will always be aligned to * sizeof(void *), size is determined in hw information. + * @uapsd_queues: bitmap of queues configured for uapsd. Only valid + * if wme is supported. + * @max_sp: max Service Period. Only valid if wme is supported. + * @bandwidth: current bandwidth the station can receive with + * @rx_nss: in HT/VHT, the maximum number of spatial streams the + * station can receive at the moment, changed by operating mode + * notifications and capabilities. The value is only valid after + * the station moves to associated state. + * @smps_mode: current SMPS mode (off, static or dynamic) + * @rates: rate control selection table + * @tdls: indicates whether the STA is a TDLS peer */ struct ieee80211_sta { u32 supp_rates[IEEE80211_NUM_BANDS]; u8 addr[ETH_ALEN]; u16 aid; struct ieee80211_sta_ht_cap ht_cap; + struct ieee80211_sta_vht_cap vht_cap; + bool wme; + u8 uapsd_queues; + u8 max_sp; + u8 rx_nss; + enum ieee80211_sta_rx_bandwidth bandwidth; + enum ieee80211_smps_mode smps_mode; + struct ieee80211_sta_rates __rcu *rates; + bool tdls; /* must be last */ - u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *)))); + u8 drv_priv[0] __aligned(sizeof(void *)); }; /** @@ -935,18 +1448,13 @@ enum sta_notify_cmd { }; /** - * enum ieee80211_tkip_key_type - get tkip key + * struct ieee80211_tx_control - TX control data * - * Used by drivers which need to get a tkip key for skb. Some drivers need a - * phase 1 key, others need a phase 2 key. A single function allows the driver - * to get the key, this enum indicates what type of key is required. - * - * @IEEE80211_TKIP_P1_KEY: the driver needs a phase 1 key - * @IEEE80211_TKIP_P2_KEY: the driver needs a phase 2 key + * @sta: station table entry, this sta pointer may be NULL and + * it is not allowed to copy the pointer, due to RCU. */ -enum ieee80211_tkip_key_type { - IEEE80211_TKIP_P1_KEY, - IEEE80211_TKIP_P2_KEY, +struct ieee80211_tx_control { + struct ieee80211_sta *sta; }; /** @@ -1020,10 +1528,6 @@ enum ieee80211_tkip_key_type { * @IEEE80211_HW_MFP_CAPABLE: * Hardware supports management frame protection (MFP, IEEE 802.11w). * - * @IEEE80211_HW_BEACON_FILTER: - * Hardware supports dropping of irrelevant beacon frames to - * avoid waking up cpu. - * * @IEEE80211_HW_SUPPORTS_STATIC_SMPS: * Hardware supports static spatial multiplexing powersave, * ie. can turn off all but one chain even on HT connections @@ -1044,19 +1548,12 @@ enum ieee80211_tkip_key_type { * the stack. * * @IEEE80211_HW_CONNECTION_MONITOR: - * The hardware performs its own connection monitoring, including - * periodic keep-alives to the AP and probing the AP on beacon loss. - * When this flag is set, signaling beacon-loss will cause an immediate - * change to disassociated state. - * - * @IEEE80211_HW_SUPPORTS_CQM_RSSI: - * Hardware can do connection quality monitoring - i.e. it can monitor - * connection quality related parameters, such as the RSSI level and - * provide notifications if configured trigger levels are reached. + * The hardware performs its own connection monitoring, including + * periodic keep-alives to the AP and probing the AP on beacon loss. * - * @IEEE80211_HW_NEED_DTIM_PERIOD: - * This device needs to know the DTIM period for the BSS before - * associating. + * @IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC: + * This device needs to get data from beacon before association (i.e. + * dtim_period). * * @IEEE80211_HW_SUPPORTS_PER_STA_GTK: The device's crypto engine supports * per-station GTKs as used by IBSS RSN or during fast transition. If @@ -1064,6 +1561,51 @@ enum ieee80211_tkip_key_type { * to decrypt group addressed frames, then IBSS RSN support is still * possible but software crypto will be used. Advertise the wiphy flag * only in that case. + * + * @IEEE80211_HW_AP_LINK_PS: When operating in AP mode the device + * autonomously manages the PS status of connected stations. When + * this flag is set mac80211 will not trigger PS mode for connected + * stations based on the PM bit of incoming frames. + * Use ieee80211_start_ps()/ieee8021_end_ps() to manually configure + * the PS mode of connected stations. + * + * @IEEE80211_HW_TX_AMPDU_SETUP_IN_HW: The device handles TX A-MPDU session + * setup strictly in HW. mac80211 should not attempt to do this in + * software. + * + * @IEEE80211_HW_WANT_MONITOR_VIF: The driver would like to be informed of + * a virtual monitor interface when monitor interfaces are the only + * active interfaces. + * + * @IEEE80211_HW_QUEUE_CONTROL: The driver wants to control per-interface + * queue mapping in order to use different queues (not just one per AC) + * for different virtual interfaces. See the doc section on HW queue + * control for more details. + * + * @IEEE80211_HW_SUPPORTS_RC_TABLE: The driver supports using a rate + * selection table provided by the rate control algorithm. + * + * @IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF: Use the P2P Device address for any + * P2P Interface. This will be honoured even if more than one interface + * is supported. + * + * @IEEE80211_HW_TIMING_BEACON_ONLY: Use sync timing from beacon frames + * only, to allow getting TBTT of a DTIM beacon. + * + * @IEEE80211_HW_SUPPORTS_HT_CCK_RATES: Hardware supports mixing HT/CCK rates + * and can cope with CCK rates in an aggregation session (e.g. by not + * using aggregation for such frames.) + * + * @IEEE80211_HW_CHANCTX_STA_CSA: Support 802.11h based channel-switch (CSA) + * for a single active channel while using channel contexts. When support + * is not enabled the default action is to disconnect when getting the + * CSA frame. + * + * @IEEE80211_HW_CHANGE_RUNNING_CHANCTX: The hardware can change a + * channel context on-the-fly. This is needed for channel switch + * on single-channel hardware. It can also be used as an + * optimization in certain channel switch cases with + * multi-channel. */ enum ieee80211_hw_flags { IEEE80211_HW_HAS_RATE_CONTROL = 1<<0, @@ -1073,21 +1615,29 @@ enum ieee80211_hw_flags { IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE = 1<<4, IEEE80211_HW_SIGNAL_UNSPEC = 1<<5, IEEE80211_HW_SIGNAL_DBM = 1<<6, - IEEE80211_HW_NEED_DTIM_PERIOD = 1<<7, + IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC = 1<<7, IEEE80211_HW_SPECTRUM_MGMT = 1<<8, IEEE80211_HW_AMPDU_AGGREGATION = 1<<9, IEEE80211_HW_SUPPORTS_PS = 1<<10, IEEE80211_HW_PS_NULLFUNC_STACK = 1<<11, IEEE80211_HW_SUPPORTS_DYNAMIC_PS = 1<<12, IEEE80211_HW_MFP_CAPABLE = 1<<13, - IEEE80211_HW_BEACON_FILTER = 1<<14, + IEEE80211_HW_WANT_MONITOR_VIF = 1<<14, IEEE80211_HW_SUPPORTS_STATIC_SMPS = 1<<15, IEEE80211_HW_SUPPORTS_DYNAMIC_SMPS = 1<<16, IEEE80211_HW_SUPPORTS_UAPSD = 1<<17, IEEE80211_HW_REPORTS_TX_ACK_STATUS = 1<<18, IEEE80211_HW_CONNECTION_MONITOR = 1<<19, - IEEE80211_HW_SUPPORTS_CQM_RSSI = 1<<20, + IEEE80211_HW_QUEUE_CONTROL = 1<<20, IEEE80211_HW_SUPPORTS_PER_STA_GTK = 1<<21, + IEEE80211_HW_AP_LINK_PS = 1<<22, + IEEE80211_HW_TX_AMPDU_SETUP_IN_HW = 1<<23, + IEEE80211_HW_SUPPORTS_RC_TABLE = 1<<24, + IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF = 1<<25, + IEEE80211_HW_TIMING_BEACON_ONLY = 1<<26, + IEEE80211_HW_SUPPORTS_HT_CCK_RATES = 1<<27, + IEEE80211_HW_CHANCTX_STA_CSA = 1<<28, + IEEE80211_HW_CHANGE_RUNNING_CHANCTX = 1<<29, }; /** @@ -1112,13 +1662,14 @@ enum ieee80211_hw_flags { * @extra_tx_headroom: headroom to reserve in each transmit skb * for use by the driver (e.g. for transmit headers.) * - * @channel_change_time: time (in microseconds) it takes to change channels. + * @extra_beacon_tailroom: tailroom to reserve in each beacon tx skb. + * Can be used by drivers to add extra IEs. * * @max_signal: Maximum value for signal (rssi) in RX information, used - * only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB + * only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB * * @max_listen_interval: max listen interval in units of beacon interval - * that HW supports + * that HW supports * * @queues: number of available hardware transmit queues for * data packets. WMM/QoS requires at least four, these @@ -1132,6 +1683,8 @@ enum ieee80211_hw_flags { * within &struct ieee80211_vif. * @sta_data_size: size (in bytes) of the drv_priv data area * within &struct ieee80211_sta. + * @chanctx_data_size: size (in bytes) of the drv_priv data area + * within &struct ieee80211_chanctx_conf. * * @max_rates: maximum number of alternate rate retry stages the hw * can handle. @@ -1139,9 +1692,47 @@ enum ieee80211_hw_flags { * the hw can report back. * @max_rate_tries: maximum number of tries for each stage * - * @napi_weight: weight used for NAPI polling. You must specify an - * appropriate value here if a napi_poll operation is provided - * by your driver. + * @max_rx_aggregation_subframes: maximum buffer size (number of + * sub-frames) to be used for A-MPDU block ack receiver + * aggregation. + * This is only relevant if the device has restrictions on the + * number of subframes, if it relies on mac80211 to do reordering + * it shouldn't be set. + * + * @max_tx_aggregation_subframes: maximum number of subframes in an + * aggregate an HT driver will transmit, used by the peer as a + * hint to size its reorder buffer. + * + * @offchannel_tx_hw_queue: HW queue ID to use for offchannel TX + * (if %IEEE80211_HW_QUEUE_CONTROL is set) + * + * @radiotap_mcs_details: lists which MCS information can the HW + * reports, by default it is set to _MCS, _GI and _BW but doesn't + * include _FMT. Use %IEEE80211_RADIOTAP_MCS_HAVE_* values, only + * adding _BW is supported today. + * + * @radiotap_vht_details: lists which VHT MCS information the HW reports, + * the default is _GI | _BANDWIDTH. + * Use the %IEEE80211_RADIOTAP_VHT_KNOWN_* values. + * + * @netdev_features: netdev features to be set in each netdev created + * from this HW. Note only HW checksum features are currently + * compatible with mac80211. Other feature bits will be rejected. + * + * @uapsd_queues: This bitmap is included in (re)association frame to indicate + * for each access category if it is uAPSD trigger-enabled and delivery- + * enabled. Use IEEE80211_WMM_IE_STA_QOSINFO_AC_* to set this bitmap. + * Each bit corresponds to different AC. Value '1' in specific bit means + * that corresponding AC is both trigger- and delivery-enabled. '0' means + * neither enabled. + * + * @uapsd_max_sp_len: maximum number of total buffered frames the WMM AP may + * deliver to a WMM STA during any Service Period triggered by the WMM STA. + * Use IEEE80211_WMM_IE_STA_QOSINFO_SP_* for correct values. + * + * @n_cipher_schemes: a size of an array of cipher schemes definitions. + * @cipher_schemes: a pointer to an array of cipher scheme definitions + * supported by HW. */ struct ieee80211_hw { struct ieee80211_conf conf; @@ -1150,16 +1741,26 @@ struct ieee80211_hw { void *priv; u32 flags; unsigned int extra_tx_headroom; - int channel_change_time; + unsigned int extra_beacon_tailroom; int vif_data_size; int sta_data_size; - int napi_weight; + int chanctx_data_size; u16 queues; u16 max_listen_interval; s8 max_signal; u8 max_rates; u8 max_report_rates; u8 max_rate_tries; + u8 max_rx_aggregation_subframes; + u8 max_tx_aggregation_subframes; + u8 offchannel_tx_hw_queue; + u8 radiotap_mcs_details; + u16 radiotap_vht_details; + netdev_features_t netdev_features; + u8 uapsd_queues; + u8 uapsd_max_sp_len; + u8 n_cipher_schemes; + const struct ieee80211_cipher_scheme *cipher_schemes; }; /** @@ -1172,6 +1773,8 @@ struct ieee80211_hw { * structure can then access it via hw->priv. Note that mac802111 drivers should * not use wiphy_priv() to try to get their private driver structure as this * is already used internally by mac80211. + * + * Return: The mac80211 driver hw struct of @wiphy. */ struct ieee80211_hw *wiphy_to_ieee80211_hw(struct wiphy *wiphy); @@ -1201,7 +1804,7 @@ static inline struct ieee80211_rate * ieee80211_get_tx_rate(const struct ieee80211_hw *hw, const struct ieee80211_tx_info *c) { - if (WARN_ON(c->control.rates[0].idx < 0)) + if (WARN_ON_ONCE(c->control.rates[0].idx < 0)) return NULL; return &hw->wiphy->bands[c->band]->bitrates[c->control.rates[0].idx]; } @@ -1225,6 +1828,16 @@ ieee80211_get_alt_retry_rate(const struct ieee80211_hw *hw, } /** + * ieee80211_free_txskb - free TX skb + * @hw: the hardware + * @skb: the skb + * + * Free a transmit skb. Use this funtion when some failure + * to transmit happened and thus status cannot be reported. + */ +void ieee80211_free_txskb(struct ieee80211_hw *hw, struct sk_buff *skb); + +/** * DOC: Hardware crypto acceleration * * mac80211 is capable of taking advantage of many hardware @@ -1263,11 +1876,15 @@ ieee80211_get_alt_retry_rate(const struct ieee80211_hw *hw, * acceleration (i.e. iwlwifi). Those drivers should provide update_tkip_key * handler. * The update_tkip_key() call updates the driver with the new phase 1 key. - * This happens everytime the iv16 wraps around (every 65536 packets). The + * This happens every time the iv16 wraps around (every 65536 packets). The * set_key() call will happen only once for each key (unless the AP did * rekeying), it will not include a valid phase 1 key. The valid phase 1 key is * provided by update_tkip_key only. The trigger that makes mac80211 call this * handler is software decryption with wrap around of iv16. + * + * The set_default_unicast_key() call updates the default WEP key index + * configured to the hardware for WEP encryption type. This is required + * for devices that support offload of data packets (e.g. ARP responses). */ /** @@ -1320,18 +1937,9 @@ ieee80211_get_alt_retry_rate(const struct ieee80211_hw *hw, * dynamic PS feature in stack and will just keep %IEEE80211_CONF_PS * enabled whenever user has enabled powersave. * - * Some hardware need to toggle a single shared antenna between WLAN and - * Bluetooth to facilitate co-existence. These types of hardware set - * limitations on the use of host controlled dynamic powersave whenever there - * is simultaneous WLAN and Bluetooth traffic. For these types of hardware, the - * driver may request temporarily going into full power save, in order to - * enable toggling the antenna between BT and WLAN. If the driver requests - * disabling dynamic powersave, the @dynamic_ps_timeout value will be - * temporarily set to zero until the driver re-enables dynamic powersave. - * * Driver informs U-APSD client support by enabling * %IEEE80211_HW_SUPPORTS_UAPSD flag. The mode is configured through the - * uapsd paramater in conf_tx() operation. Hardware needs to send the QoS + * uapsd parameter in conf_tx() operation. Hardware needs to send the QoS * Nullfunc frames and stay awake until the service period has ended. To * utilize U-APSD, dynamic powersave is disabled for voip AC and all frames * from that AC are transmitted with powersave enabled. @@ -1344,15 +1952,15 @@ ieee80211_get_alt_retry_rate(const struct ieee80211_hw *hw, * DOC: Beacon filter support * * Some hardware have beacon filter support to reduce host cpu wakeups - * which will reduce system power consumption. It usuallly works so that + * which will reduce system power consumption. It usually works so that * the firmware creates a checksum of the beacon but omits all constantly * changing elements (TSF, TIM etc). Whenever the checksum changes the * beacon is forwarded to the host, otherwise it will be just dropped. That * way the host will only receive beacons where some relevant information * (for example ERP protection or WMM settings) have changed. * - * Beacon filter support is advertised with the %IEEE80211_HW_BEACON_FILTER - * hardware capability. The driver needs to enable beacon filter support + * Beacon filter support is advertised with the %IEEE80211_VIF_BEACON_FILTER + * interface capability. The driver needs to enable beacon filter support * whenever power save is enabled, that is %IEEE80211_CONF_PS is set. When * power save is enabled, the stack will not check for beacon loss and the * driver needs to notify about loss of beacons with ieee80211_beacon_loss(). @@ -1466,6 +2074,158 @@ ieee80211_get_alt_retry_rate(const struct ieee80211_hw *hw, */ /** + * DOC: AP support for powersaving clients + * + * In order to implement AP and P2P GO modes, mac80211 has support for + * client powersaving, both "legacy" PS (PS-Poll/null data) and uAPSD. + * There currently is no support for sAPSD. + * + * There is one assumption that mac80211 makes, namely that a client + * will not poll with PS-Poll and trigger with uAPSD at the same time. + * Both are supported, and both can be used by the same client, but + * they can't be used concurrently by the same client. This simplifies + * the driver code. + * + * The first thing to keep in mind is that there is a flag for complete + * driver implementation: %IEEE80211_HW_AP_LINK_PS. If this flag is set, + * mac80211 expects the driver to handle most of the state machine for + * powersaving clients and will ignore the PM bit in incoming frames. + * Drivers then use ieee80211_sta_ps_transition() to inform mac80211 of + * stations' powersave transitions. In this mode, mac80211 also doesn't + * handle PS-Poll/uAPSD. + * + * In the mode without %IEEE80211_HW_AP_LINK_PS, mac80211 will check the + * PM bit in incoming frames for client powersave transitions. When a + * station goes to sleep, we will stop transmitting to it. There is, + * however, a race condition: a station might go to sleep while there is + * data buffered on hardware queues. If the device has support for this + * it will reject frames, and the driver should give the frames back to + * mac80211 with the %IEEE80211_TX_STAT_TX_FILTERED flag set which will + * cause mac80211 to retry the frame when the station wakes up. The + * driver is also notified of powersave transitions by calling its + * @sta_notify callback. + * + * When the station is asleep, it has three choices: it can wake up, + * it can PS-Poll, or it can possibly start a uAPSD service period. + * Waking up is implemented by simply transmitting all buffered (and + * filtered) frames to the station. This is the easiest case. When + * the station sends a PS-Poll or a uAPSD trigger frame, mac80211 + * will inform the driver of this with the @allow_buffered_frames + * callback; this callback is optional. mac80211 will then transmit + * the frames as usual and set the %IEEE80211_TX_CTL_NO_PS_BUFFER + * on each frame. The last frame in the service period (or the only + * response to a PS-Poll) also has %IEEE80211_TX_STATUS_EOSP set to + * indicate that it ends the service period; as this frame must have + * TX status report it also sets %IEEE80211_TX_CTL_REQ_TX_STATUS. + * When TX status is reported for this frame, the service period is + * marked has having ended and a new one can be started by the peer. + * + * Additionally, non-bufferable MMPDUs can also be transmitted by + * mac80211 with the %IEEE80211_TX_CTL_NO_PS_BUFFER set in them. + * + * Another race condition can happen on some devices like iwlwifi + * when there are frames queued for the station and it wakes up + * or polls; the frames that are already queued could end up being + * transmitted first instead, causing reordering and/or wrong + * processing of the EOSP. The cause is that allowing frames to be + * transmitted to a certain station is out-of-band communication to + * the device. To allow this problem to be solved, the driver can + * call ieee80211_sta_block_awake() if frames are buffered when it + * is notified that the station went to sleep. When all these frames + * have been filtered (see above), it must call the function again + * to indicate that the station is no longer blocked. + * + * If the driver buffers frames in the driver for aggregation in any + * way, it must use the ieee80211_sta_set_buffered() call when it is + * notified of the station going to sleep to inform mac80211 of any + * TIDs that have frames buffered. Note that when a station wakes up + * this information is reset (hence the requirement to call it when + * informed of the station going to sleep). Then, when a service + * period starts for any reason, @release_buffered_frames is called + * with the number of frames to be released and which TIDs they are + * to come from. In this case, the driver is responsible for setting + * the EOSP (for uAPSD) and MORE_DATA bits in the released frames, + * to help the @more_data parameter is passed to tell the driver if + * there is more data on other TIDs -- the TIDs to release frames + * from are ignored since mac80211 doesn't know how many frames the + * buffers for those TIDs contain. + * + * If the driver also implement GO mode, where absence periods may + * shorten service periods (or abort PS-Poll responses), it must + * filter those response frames except in the case of frames that + * are buffered in the driver -- those must remain buffered to avoid + * reordering. Because it is possible that no frames are released + * in this case, the driver must call ieee80211_sta_eosp() + * to indicate to mac80211 that the service period ended anyway. + * + * Finally, if frames from multiple TIDs are released from mac80211 + * but the driver might reorder them, it must clear & set the flags + * appropriately (only the last frame may have %IEEE80211_TX_STATUS_EOSP) + * and also take care of the EOSP and MORE_DATA bits in the frame. + * The driver may also use ieee80211_sta_eosp() in this case. + * + * Note that if the driver ever buffers frames other than QoS-data + * frames, it must take care to never send a non-QoS-data frame as + * the last frame in a service period, adding a QoS-nulldata frame + * after a non-QoS-data frame if needed. + */ + +/** + * DOC: HW queue control + * + * Before HW queue control was introduced, mac80211 only had a single static + * assignment of per-interface AC software queues to hardware queues. This + * was problematic for a few reasons: + * 1) off-channel transmissions might get stuck behind other frames + * 2) multiple virtual interfaces couldn't be handled correctly + * 3) after-DTIM frames could get stuck behind other frames + * + * To solve this, hardware typically uses multiple different queues for all + * the different usages, and this needs to be propagated into mac80211 so it + * won't have the same problem with the software queues. + * + * Therefore, mac80211 now offers the %IEEE80211_HW_QUEUE_CONTROL capability + * flag that tells it that the driver implements its own queue control. To do + * so, the driver will set up the various queues in each &struct ieee80211_vif + * and the offchannel queue in &struct ieee80211_hw. In response, mac80211 will + * use those queue IDs in the hw_queue field of &struct ieee80211_tx_info and + * if necessary will queue the frame on the right software queue that mirrors + * the hardware queue. + * Additionally, the driver has to then use these HW queue IDs for the queue + * management functions (ieee80211_stop_queue() et al.) + * + * The driver is free to set up the queue mappings as needed, multiple virtual + * interfaces may map to the same hardware queues if needed. The setup has to + * happen during add_interface or change_interface callbacks. For example, a + * driver supporting station+station and station+AP modes might decide to have + * 10 hardware queues to handle different scenarios: + * + * 4 AC HW queues for 1st vif: 0, 1, 2, 3 + * 4 AC HW queues for 2nd vif: 4, 5, 6, 7 + * after-DTIM queue for AP: 8 + * off-channel queue: 9 + * + * It would then set up the hardware like this: + * hw.offchannel_tx_hw_queue = 9 + * + * and the first virtual interface that is added as follows: + * vif.hw_queue[IEEE80211_AC_VO] = 0 + * vif.hw_queue[IEEE80211_AC_VI] = 1 + * vif.hw_queue[IEEE80211_AC_BE] = 2 + * vif.hw_queue[IEEE80211_AC_BK] = 3 + * vif.cab_queue = 8 // if AP mode, otherwise %IEEE80211_INVAL_HW_QUEUE + * and the second virtual interface with 4-7. + * + * If queue 6 gets full, for example, mac80211 would only stop the second + * virtual interface's BE queue since virtual interface queues are per AC. + * + * Note that the vif.cab_queue value should be set to %IEEE80211_INVAL_HW_QUEUE + * whenever the queue is not used (i.e. the interface is not in AP mode) if the + * queue could potentially be shared since mac80211 will look at cab_queue when + * a queue is stopped/woken even if the interface is not in AP mode. + */ + +/** * enum ieee80211_filter_flags - hardware filter flags * * These flags determine what the filter in hardware should be @@ -1526,21 +2286,83 @@ enum ieee80211_filter_flags { * calling ieee80211_start_tx_ba_cb_irqsafe, because the peer * might receive the addBA frame and send a delBA right away! * - * @IEEE80211_AMPDU_RX_START: start Rx aggregation - * @IEEE80211_AMPDU_RX_STOP: stop Rx aggregation - * @IEEE80211_AMPDU_TX_START: start Tx aggregation - * @IEEE80211_AMPDU_TX_STOP: stop Tx aggregation + * @IEEE80211_AMPDU_RX_START: start RX aggregation + * @IEEE80211_AMPDU_RX_STOP: stop RX aggregation + * @IEEE80211_AMPDU_TX_START: start TX aggregation * @IEEE80211_AMPDU_TX_OPERATIONAL: TX aggregation has become operational + * @IEEE80211_AMPDU_TX_STOP_CONT: stop TX aggregation but continue transmitting + * queued packets, now unaggregated. After all packets are transmitted the + * driver has to call ieee80211_stop_tx_ba_cb_irqsafe(). + * @IEEE80211_AMPDU_TX_STOP_FLUSH: stop TX aggregation and flush all packets, + * called when the station is removed. There's no need or reason to call + * ieee80211_stop_tx_ba_cb_irqsafe() in this case as mac80211 assumes the + * session is gone and removes the station. + * @IEEE80211_AMPDU_TX_STOP_FLUSH_CONT: called when TX aggregation is stopped + * but the driver hasn't called ieee80211_stop_tx_ba_cb_irqsafe() yet and + * now the connection is dropped and the station will be removed. Drivers + * should clean up and drop remaining packets when this is called. */ enum ieee80211_ampdu_mlme_action { IEEE80211_AMPDU_RX_START, IEEE80211_AMPDU_RX_STOP, IEEE80211_AMPDU_TX_START, - IEEE80211_AMPDU_TX_STOP, + IEEE80211_AMPDU_TX_STOP_CONT, + IEEE80211_AMPDU_TX_STOP_FLUSH, + IEEE80211_AMPDU_TX_STOP_FLUSH_CONT, IEEE80211_AMPDU_TX_OPERATIONAL, }; /** + * enum ieee80211_frame_release_type - frame release reason + * @IEEE80211_FRAME_RELEASE_PSPOLL: frame released for PS-Poll + * @IEEE80211_FRAME_RELEASE_UAPSD: frame(s) released due to + * frame received on trigger-enabled AC + */ +enum ieee80211_frame_release_type { + IEEE80211_FRAME_RELEASE_PSPOLL, + IEEE80211_FRAME_RELEASE_UAPSD, +}; + +/** + * enum ieee80211_rate_control_changed - flags to indicate what changed + * + * @IEEE80211_RC_BW_CHANGED: The bandwidth that can be used to transmit + * to this station changed. The actual bandwidth is in the station + * information -- for HT20/40 the IEEE80211_HT_CAP_SUP_WIDTH_20_40 + * flag changes, for HT and VHT the bandwidth field changes. + * @IEEE80211_RC_SMPS_CHANGED: The SMPS state of the station changed. + * @IEEE80211_RC_SUPP_RATES_CHANGED: The supported rate set of this peer + * changed (in IBSS mode) due to discovering more information about + * the peer. + * @IEEE80211_RC_NSS_CHANGED: N_SS (number of spatial streams) was changed + * by the peer + */ +enum ieee80211_rate_control_changed { + IEEE80211_RC_BW_CHANGED = BIT(0), + IEEE80211_RC_SMPS_CHANGED = BIT(1), + IEEE80211_RC_SUPP_RATES_CHANGED = BIT(2), + IEEE80211_RC_NSS_CHANGED = BIT(3), +}; + +/** + * enum ieee80211_roc_type - remain on channel type + * + * With the support for multi channel contexts and multi channel operations, + * remain on channel operations might be limited/deferred/aborted by other + * flows/operations which have higher priority (and vise versa). + * Specifying the ROC type can be used by devices to prioritize the ROC + * operations compared to other operations/flows. + * + * @IEEE80211_ROC_TYPE_NORMAL: There are no special requirements for this ROC. + * @IEEE80211_ROC_TYPE_MGMT_TX: The remain on channel request is required + * for sending managment frames offchannel. + */ +enum ieee80211_roc_type { + IEEE80211_ROC_TYPE_NORMAL = 0, + IEEE80211_ROC_TYPE_MGMT_TX, +}; + +/** * struct ieee80211_ops - callbacks from mac80211 to the driver * * This structure contains various callbacks that the driver may @@ -1551,11 +2373,8 @@ enum ieee80211_ampdu_mlme_action { * skb contains the buffer starting from the IEEE 802.11 header. * The low-level driver should send the frame out based on * configuration in the TX control data. This handler should, - * preferably, never fail and stop queues appropriately, more - * importantly, however, it must never fail for A-MPDU-queues. - * This function should return NETDEV_TX_OK except in very - * limited cases. - * Must be implemented and atomic. + * preferably, never fail and stop queues appropriately. + * Must be atomic. * * @start: Called before the first netdevice attached to the hardware * is enabled. This should turn on the hardware and must turn on @@ -1575,6 +2394,27 @@ enum ieee80211_ampdu_mlme_action { * you should ensure to cancel it on this callback. * Must be implemented and can sleep. * + * @suspend: Suspend the device; mac80211 itself will quiesce before and + * stop transmitting and doing any other configuration, and then + * ask the device to suspend. This is only invoked when WoWLAN is + * configured, otherwise the device is deconfigured completely and + * reconfigured at resume time. + * The driver may also impose special conditions under which it + * wants to use the "normal" suspend (deconfigure), say if it only + * supports WoWLAN when the device is associated. In this case, it + * must return 1 from this function. + * + * @resume: If WoWLAN was configured, this indicates that mac80211 is + * now resuming its operation, after this the device must be fully + * functional again. If this returns an error, the only way out is + * to also unregister the device. If it returns 1, then mac80211 + * will also go through the regular complete restart on resume. + * + * @set_wakeup: Enable or disable wakeup when WoWLAN configuration is + * modified. The reason is that device_set_wakeup_enable() is + * supposed to be called when the configuration changes, not only + * in suspend(). + * * @add_interface: Called when a netdevice attached to the hardware is * enabled. Because it is not called for monitor mode devices, @start * and @stop must be implemented. @@ -1636,6 +2476,16 @@ enum ieee80211_ampdu_mlme_action { * which set IEEE80211_KEY_FLAG_TKIP_REQ_RX_P1_KEY. * The callback must be atomic. * + * @set_rekey_data: If the device supports GTK rekeying, for example while the + * host is suspended, it can assign this callback to retrieve the data + * necessary to do GTK rekeying, this is the KEK, KCK and replay counter. + * After rekeying was done it should (for example during resume) notify + * userspace of the new replay counter using ieee80211_gtk_rekey_notify(). + * + * @set_default_unicast_key: Set the default (unicast) key index, useful for + * WEP when the device sends data packets autonomously, e.g. for ARP + * offloading. The index can be 0-3, or -1 for unsetting it. + * * @hw_scan: Ask the hardware to service the scan request, no need to start * the scan state machine in stack. The scan must honour the channel * configuration done by the regulatory agent in the wiphy's @@ -1650,6 +2500,22 @@ enum ieee80211_ampdu_mlme_action { * any error unless this callback returned a negative error code. * The callback can sleep. * + * @cancel_hw_scan: Ask the low-level tp cancel the active hw scan. + * The driver should ask the hardware to cancel the scan (if possible), + * but the scan will be completed only after the driver will call + * ieee80211_scan_completed(). + * This callback is needed for wowlan, to prevent enqueueing a new + * scan_work after the low-level driver was already suspended. + * The callback can sleep. + * + * @sched_scan_start: Ask the hardware to start scanning repeatedly at + * specific intervals. The driver must call the + * ieee80211_sched_scan_results() function whenever it finds results. + * This process will continue until sched_scan_stop is called. + * + * @sched_scan_stop: Tell the hardware to stop an ongoing scheduled scan. + * In this case, ieee80211_sched_scan_stopped() must not be called. + * * @sw_scan_start: Notifier function that is called just before a software scan * is started. Can be NULL, if the driver doesn't need this notification. * The callback can sleep. @@ -1680,10 +2546,49 @@ enum ieee80211_ampdu_mlme_action { * AP, IBSS/WDS/mesh peer etc. This callback can sleep. * * @sta_remove: Notifies low level driver about removal of an associated - * station, AP, IBSS/WDS/mesh peer etc. This callback can sleep. + * station, AP, IBSS/WDS/mesh peer etc. Note that after the callback + * returns it isn't safe to use the pointer, not even RCU protected; + * no RCU grace period is guaranteed between returning here and freeing + * the station. See @sta_pre_rcu_remove if needed. + * This callback can sleep. + * + * @sta_add_debugfs: Drivers can use this callback to add debugfs files + * when a station is added to mac80211's station list. This callback + * and @sta_remove_debugfs should be within a CONFIG_MAC80211_DEBUGFS + * conditional. This callback can sleep. + * + * @sta_remove_debugfs: Remove the debugfs files which were added using + * @sta_add_debugfs. This callback can sleep. * * @sta_notify: Notifies low level driver about power state transition of an - * associated station, AP, IBSS/WDS/mesh peer etc. Must be atomic. + * associated station, AP, IBSS/WDS/mesh peer etc. For a VIF operating + * in AP mode, this callback will not be called when the flag + * %IEEE80211_HW_AP_LINK_PS is set. Must be atomic. + * + * @sta_state: Notifies low level driver about state transition of a + * station (which can be the AP, a client, IBSS/WDS/mesh peer etc.) + * This callback is mutually exclusive with @sta_add/@sta_remove. + * It must not fail for down transitions but may fail for transitions + * up the list of states. Also note that after the callback returns it + * isn't safe to use the pointer, not even RCU protected - no RCU grace + * period is guaranteed between returning here and freeing the station. + * See @sta_pre_rcu_remove if needed. + * The callback can sleep. + * + * @sta_pre_rcu_remove: Notify driver about station removal before RCU + * synchronisation. This is useful if a driver needs to have station + * pointers protected using RCU, it can then use this call to clear + * the pointers instead of waiting for an RCU grace period to elapse + * in @sta_state. + * The callback can sleep. + * + * @sta_rc_update: Notifies the driver of changes to the bitrates that can be + * used to transmit to the station. The changes are advertised with bits + * from &enum ieee80211_rate_control_changed and the values are reflected + * in the station data. This callback should only be used when the driver + * uses hardware rate control (%IEEE80211_HW_HAS_RATE_CONTROL) since + * otherwise the rate control algorithm is notified directly. + * Must be atomic. * * @conf_tx: Configure TX queue parameters (EDCF (aifs, cw_min, cw_max), * bursting) for a hardware TX queue. @@ -1696,7 +2601,7 @@ enum ieee80211_ampdu_mlme_action { * The callback can sleep. * * @set_tsf: Set the TSF timer to the specified value in the firmware/hardware. - * Currently, this is only used for IBSS mode debugging. Is not a + * Currently, this is only used for IBSS mode debugging. Is not a * required function. * The callback can sleep. * @@ -1718,6 +2623,21 @@ enum ieee80211_ampdu_mlme_action { * ieee80211_ampdu_mlme_action. Starting sequence number (@ssn) * is the first frame we expect to perform the action on. Notice * that TX/RX_STOP can pass NULL for this parameter. + * The @buf_size parameter is only valid when the action is set to + * %IEEE80211_AMPDU_TX_OPERATIONAL and indicates the peer's reorder + * buffer size (number of subframes) for this session -- the driver + * may neither send aggregates containing more subframes than this + * nor send aggregates in a way that lost frames would exceed the + * buffer size. If just limiting the aggregate size, this would be + * possible with a buf_size of 8: + * - TX: 1.....7 + * - RX: 2....7 (lost frame #1) + * - TX: 8..1... + * which is invalid since #1 was now re-transmitted well past the + * buffer size of 8. Correct ways to retransmit #1 would be: + * - TX: 1 or 18 or 81 + * Even "189" would be wrong since 1 could be lost again. + * * Returns a negative error code on failure. * The callback can sleep. * @@ -1732,31 +2652,181 @@ enum ieee80211_ampdu_mlme_action { * in IEEE 802.11-2007 section 17.3.8.6 and modify ACK timeout * accordingly. This callback is not required and may sleep. * - * @testmode_cmd: Implement a cfg80211 test mode command. - * The callback can sleep. + * @testmode_cmd: Implement a cfg80211 test mode command. The passed @vif may + * be %NULL. The callback can sleep. + * @testmode_dump: Implement a cfg80211 test mode dump. The callback can sleep. * * @flush: Flush all pending frames from the hardware queue, making sure - * that the hardware queues are empty. If the parameter @drop is set - * to %true, pending frames may be dropped. The callback can sleep. + * that the hardware queues are empty. The @queues parameter is a bitmap + * of queues to flush, which is useful if different virtual interfaces + * use different hardware queues; it may also indicate all queues. + * If the parameter @drop is set to %true, pending frames may be dropped. + * Note that vif can be NULL. + * The callback can sleep. * * @channel_switch: Drivers that need (or want) to offload the channel * switch operation for CSAs received from the AP may implement this * callback. They must then call ieee80211_chswitch_done() to indicate * completion of the channel switch. * - * @napi_poll: Poll Rx queue for incoming data frames. - * * @set_antenna: Set antenna configuration (tx_ant, rx_ant) on the device. * Parameters are bitmaps of allowed antennas to use for TX/RX. Drivers may * reject TX/RX mask combinations they cannot support by returning -EINVAL * (also see nl80211.h @NL80211_ATTR_WIPHY_ANTENNA_TX). * * @get_antenna: Get current antenna configuration from device (tx_ant, rx_ant). + * + * @remain_on_channel: Starts an off-channel period on the given channel, must + * call back to ieee80211_ready_on_channel() when on that channel. Note + * that normal channel traffic is not stopped as this is intended for hw + * offload. Frames to transmit on the off-channel channel are transmitted + * normally except for the %IEEE80211_TX_CTL_TX_OFFCHAN flag. When the + * duration (which will always be non-zero) expires, the driver must call + * ieee80211_remain_on_channel_expired(). + * Note that this callback may be called while the device is in IDLE and + * must be accepted in this case. + * This callback may sleep. + * @cancel_remain_on_channel: Requests that an ongoing off-channel period is + * aborted before it expires. This callback may sleep. + * + * @set_ringparam: Set tx and rx ring sizes. + * + * @get_ringparam: Get tx and rx ring current and maximum sizes. + * + * @tx_frames_pending: Check if there is any pending frame in the hardware + * queues before entering power save. + * + * @set_bitrate_mask: Set a mask of rates to be used for rate control selection + * when transmitting a frame. Currently only legacy rates are handled. + * The callback can sleep. + * @rssi_callback: Notify driver when the average RSSI goes above/below + * thresholds that were registered previously. The callback can sleep. + * + * @release_buffered_frames: Release buffered frames according to the given + * parameters. In the case where the driver buffers some frames for + * sleeping stations mac80211 will use this callback to tell the driver + * to release some frames, either for PS-poll or uAPSD. + * Note that if the @more_data parameter is %false the driver must check + * if there are more frames on the given TIDs, and if there are more than + * the frames being released then it must still set the more-data bit in + * the frame. If the @more_data parameter is %true, then of course the + * more-data bit must always be set. + * The @tids parameter tells the driver which TIDs to release frames + * from, for PS-poll it will always have only a single bit set. + * In the case this is used for a PS-poll initiated release, the + * @num_frames parameter will always be 1 so code can be shared. In + * this case the driver must also set %IEEE80211_TX_STATUS_EOSP flag + * on the TX status (and must report TX status) so that the PS-poll + * period is properly ended. This is used to avoid sending multiple + * responses for a retried PS-poll frame. + * In the case this is used for uAPSD, the @num_frames parameter may be + * bigger than one, but the driver may send fewer frames (it must send + * at least one, however). In this case it is also responsible for + * setting the EOSP flag in the QoS header of the frames. Also, when the + * service period ends, the driver must set %IEEE80211_TX_STATUS_EOSP + * on the last frame in the SP. Alternatively, it may call the function + * ieee80211_sta_eosp() to inform mac80211 of the end of the SP. + * This callback must be atomic. + * @allow_buffered_frames: Prepare device to allow the given number of frames + * to go out to the given station. The frames will be sent by mac80211 + * via the usual TX path after this call. The TX information for frames + * released will also have the %IEEE80211_TX_CTL_NO_PS_BUFFER flag set + * and the last one will also have %IEEE80211_TX_STATUS_EOSP set. In case + * frames from multiple TIDs are released and the driver might reorder + * them between the TIDs, it must set the %IEEE80211_TX_STATUS_EOSP flag + * on the last frame and clear it on all others and also handle the EOSP + * bit in the QoS header correctly. Alternatively, it can also call the + * ieee80211_sta_eosp() function. + * The @tids parameter is a bitmap and tells the driver which TIDs the + * frames will be on; it will at most have two bits set. + * This callback must be atomic. + * + * @get_et_sset_count: Ethtool API to get string-set count. + * + * @get_et_stats: Ethtool API to get a set of u64 stats. + * + * @get_et_strings: Ethtool API to get a set of strings to describe stats + * and perhaps other supported types of ethtool data-sets. + * + * @get_rssi: Get current signal strength in dBm, the function is optional + * and can sleep. + * + * @mgd_prepare_tx: Prepare for transmitting a management frame for association + * before associated. In multi-channel scenarios, a virtual interface is + * bound to a channel before it is associated, but as it isn't associated + * yet it need not necessarily be given airtime, in particular since any + * transmission to a P2P GO needs to be synchronized against the GO's + * powersave state. mac80211 will call this function before transmitting a + * management frame prior to having successfully associated to allow the + * driver to give it channel time for the transmission, to get a response + * and to be able to synchronize with the GO. + * The callback will be called before each transmission and upon return + * mac80211 will transmit the frame right away. + * The callback is optional and can (should!) sleep. + * + * @add_chanctx: Notifies device driver about new channel context creation. + * @remove_chanctx: Notifies device driver about channel context destruction. + * @change_chanctx: Notifies device driver about channel context changes that + * may happen when combining different virtual interfaces on the same + * channel context with different settings + * @assign_vif_chanctx: Notifies device driver about channel context being bound + * to vif. Possible use is for hw queue remapping. + * @unassign_vif_chanctx: Notifies device driver about channel context being + * unbound from vif. + * @switch_vif_chanctx: switch a number of vifs from one chanctx to + * another, as specified in the list of + * @ieee80211_vif_chanctx_switch passed to the driver, according + * to the mode defined in &ieee80211_chanctx_switch_mode. + * + * @start_ap: Start operation on the AP interface, this is called after all the + * information in bss_conf is set and beacon can be retrieved. A channel + * context is bound before this is called. Note that if the driver uses + * software scan or ROC, this (and @stop_ap) isn't called when the AP is + * just "paused" for scanning/ROC, which is indicated by the beacon being + * disabled/enabled via @bss_info_changed. + * @stop_ap: Stop operation on the AP interface. + * + * @restart_complete: Called after a call to ieee80211_restart_hw(), when the + * reconfiguration has completed. This can help the driver implement the + * reconfiguration step. Also called when reconfiguring because the + * driver's resume function returned 1, as this is just like an "inline" + * hardware restart. This callback may sleep. + * + * @ipv6_addr_change: IPv6 address assignment on the given interface changed. + * Currently, this is only called for managed or P2P client interfaces. + * This callback is optional; it must not sleep. + * + * @channel_switch_beacon: Starts a channel switch to a new channel. + * Beacons are modified to include CSA or ECSA IEs before calling this + * function. The corresponding count fields in these IEs must be + * decremented, and when they reach 1 the driver must call + * ieee80211_csa_finish(). Drivers which use ieee80211_beacon_get() + * get the csa counter decremented by mac80211, but must check if it is + * 1 using ieee80211_csa_is_complete() after the beacon has been + * transmitted and then call ieee80211_csa_finish(). + * If the CSA count starts as zero or 1, this function will not be called, + * since there won't be any time to beacon before the switch anyway. + * + * @join_ibss: Join an IBSS (on an IBSS interface); this is called after all + * information in bss_conf is set up and the beacon can be retrieved. A + * channel context is bound before this is called. + * @leave_ibss: Leave the IBSS again. + * + * @get_expected_throughput: extract the expected throughput towards the + * specified station. The returned value is expressed in Kbps. It returns 0 + * if the RC algorithm does not have proper data to provide. */ struct ieee80211_ops { - int (*tx)(struct ieee80211_hw *hw, struct sk_buff *skb); + void (*tx)(struct ieee80211_hw *hw, + struct ieee80211_tx_control *control, + struct sk_buff *skb); int (*start)(struct ieee80211_hw *hw); void (*stop)(struct ieee80211_hw *hw); +#ifdef CONFIG_PM + int (*suspend)(struct ieee80211_hw *hw, struct cfg80211_wowlan *wowlan); + int (*resume)(struct ieee80211_hw *hw); + void (*set_wakeup)(struct ieee80211_hw *hw, bool enabled); +#endif int (*add_interface)(struct ieee80211_hw *hw, struct ieee80211_vif *vif); int (*change_interface)(struct ieee80211_hw *hw, @@ -1769,6 +2839,10 @@ struct ieee80211_ops { struct ieee80211_vif *vif, struct ieee80211_bss_conf *info, u32 changed); + + int (*start_ap)(struct ieee80211_hw *hw, struct ieee80211_vif *vif); + void (*stop_ap)(struct ieee80211_hw *hw, struct ieee80211_vif *vif); + u64 (*prepare_multicast)(struct ieee80211_hw *hw, struct netdev_hw_addr_list *mc_list); void (*configure_filter)(struct ieee80211_hw *hw, @@ -1785,8 +2859,21 @@ struct ieee80211_ops { struct ieee80211_key_conf *conf, struct ieee80211_sta *sta, u32 iv32, u16 *phase1key); + void (*set_rekey_data)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct cfg80211_gtk_rekey_data *data); + void (*set_default_unicast_key)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, int idx); int (*hw_scan)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, struct cfg80211_scan_request *req); + void (*cancel_hw_scan)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif); + int (*sched_scan_start)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct cfg80211_sched_scan_request *req, + struct ieee80211_sched_scan_ies *ies); + int (*sched_scan_stop)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif); void (*sw_scan_start)(struct ieee80211_hw *hw); void (*sw_scan_complete)(struct ieee80211_hw *hw); int (*get_stats)(struct ieee80211_hw *hw, @@ -1799,31 +2886,133 @@ struct ieee80211_ops { struct ieee80211_sta *sta); int (*sta_remove)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, struct ieee80211_sta *sta); +#ifdef CONFIG_MAC80211_DEBUGFS + void (*sta_add_debugfs)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct ieee80211_sta *sta, + struct dentry *dir); + void (*sta_remove_debugfs)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct ieee80211_sta *sta, + struct dentry *dir); +#endif void (*sta_notify)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, enum sta_notify_cmd, struct ieee80211_sta *sta); - int (*conf_tx)(struct ieee80211_hw *hw, u16 queue, + int (*sta_state)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, + struct ieee80211_sta *sta, + enum ieee80211_sta_state old_state, + enum ieee80211_sta_state new_state); + void (*sta_pre_rcu_remove)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct ieee80211_sta *sta); + void (*sta_rc_update)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct ieee80211_sta *sta, + u32 changed); + int (*conf_tx)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, u16 ac, const struct ieee80211_tx_queue_params *params); - u64 (*get_tsf)(struct ieee80211_hw *hw); - void (*set_tsf)(struct ieee80211_hw *hw, u64 tsf); - void (*reset_tsf)(struct ieee80211_hw *hw); + u64 (*get_tsf)(struct ieee80211_hw *hw, struct ieee80211_vif *vif); + void (*set_tsf)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, + u64 tsf); + void (*reset_tsf)(struct ieee80211_hw *hw, struct ieee80211_vif *vif); int (*tx_last_beacon)(struct ieee80211_hw *hw); int (*ampdu_action)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, enum ieee80211_ampdu_mlme_action action, - struct ieee80211_sta *sta, u16 tid, u16 *ssn); + struct ieee80211_sta *sta, u16 tid, u16 *ssn, + u8 buf_size); int (*get_survey)(struct ieee80211_hw *hw, int idx, struct survey_info *survey); void (*rfkill_poll)(struct ieee80211_hw *hw); void (*set_coverage_class)(struct ieee80211_hw *hw, u8 coverage_class); #ifdef CONFIG_NL80211_TESTMODE - int (*testmode_cmd)(struct ieee80211_hw *hw, void *data, int len); + int (*testmode_cmd)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, + void *data, int len); + int (*testmode_dump)(struct ieee80211_hw *hw, struct sk_buff *skb, + struct netlink_callback *cb, + void *data, int len); #endif - void (*flush)(struct ieee80211_hw *hw, bool drop); + void (*flush)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, + u32 queues, bool drop); void (*channel_switch)(struct ieee80211_hw *hw, struct ieee80211_channel_switch *ch_switch); - int (*napi_poll)(struct ieee80211_hw *hw, int budget); int (*set_antenna)(struct ieee80211_hw *hw, u32 tx_ant, u32 rx_ant); int (*get_antenna)(struct ieee80211_hw *hw, u32 *tx_ant, u32 *rx_ant); + + int (*remain_on_channel)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct ieee80211_channel *chan, + int duration, + enum ieee80211_roc_type type); + int (*cancel_remain_on_channel)(struct ieee80211_hw *hw); + int (*set_ringparam)(struct ieee80211_hw *hw, u32 tx, u32 rx); + void (*get_ringparam)(struct ieee80211_hw *hw, + u32 *tx, u32 *tx_max, u32 *rx, u32 *rx_max); + bool (*tx_frames_pending)(struct ieee80211_hw *hw); + int (*set_bitrate_mask)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, + const struct cfg80211_bitrate_mask *mask); + void (*rssi_callback)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + enum ieee80211_rssi_event rssi_event); + + void (*allow_buffered_frames)(struct ieee80211_hw *hw, + struct ieee80211_sta *sta, + u16 tids, int num_frames, + enum ieee80211_frame_release_type reason, + bool more_data); + void (*release_buffered_frames)(struct ieee80211_hw *hw, + struct ieee80211_sta *sta, + u16 tids, int num_frames, + enum ieee80211_frame_release_type reason, + bool more_data); + + int (*get_et_sset_count)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, int sset); + void (*get_et_stats)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct ethtool_stats *stats, u64 *data); + void (*get_et_strings)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + u32 sset, u8 *data); + int (*get_rssi)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, + struct ieee80211_sta *sta, s8 *rssi_dbm); + + void (*mgd_prepare_tx)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif); + + int (*add_chanctx)(struct ieee80211_hw *hw, + struct ieee80211_chanctx_conf *ctx); + void (*remove_chanctx)(struct ieee80211_hw *hw, + struct ieee80211_chanctx_conf *ctx); + void (*change_chanctx)(struct ieee80211_hw *hw, + struct ieee80211_chanctx_conf *ctx, + u32 changed); + int (*assign_vif_chanctx)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct ieee80211_chanctx_conf *ctx); + void (*unassign_vif_chanctx)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct ieee80211_chanctx_conf *ctx); + int (*switch_vif_chanctx)(struct ieee80211_hw *hw, + struct ieee80211_vif_chanctx_switch *vifs, + int n_vifs, + enum ieee80211_chanctx_switch_mode mode); + + void (*restart_complete)(struct ieee80211_hw *hw); + +#if IS_ENABLED(CONFIG_IPV6) + void (*ipv6_addr_change)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct inet6_dev *idev); +#endif + void (*channel_switch_beacon)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct cfg80211_chan_def *chandef); + + int (*join_ibss)(struct ieee80211_hw *hw, struct ieee80211_vif *vif); + void (*leave_ibss)(struct ieee80211_hw *hw, struct ieee80211_vif *vif); + u32 (*get_expected_throughput)(struct ieee80211_sta *sta); }; /** @@ -1837,6 +3026,8 @@ struct ieee80211_ops { * * @priv_data_len: length of private data * @ops: callbacks for this device + * + * Return: A pointer to the new hardware device, or %NULL on error. */ struct ieee80211_hw *ieee80211_alloc_hw(size_t priv_data_len, const struct ieee80211_ops *ops); @@ -1849,14 +3040,44 @@ struct ieee80211_hw *ieee80211_alloc_hw(size_t priv_data_len, * need to fill the contained wiphy's information. * * @hw: the device to register as returned by ieee80211_alloc_hw() + * + * Return: 0 on success. An error code otherwise. */ int ieee80211_register_hw(struct ieee80211_hw *hw); +/** + * struct ieee80211_tpt_blink - throughput blink description + * @throughput: throughput in Kbit/sec + * @blink_time: blink time in milliseconds + * (full cycle, ie. one off + one on period) + */ +struct ieee80211_tpt_blink { + int throughput; + int blink_time; +}; + +/** + * enum ieee80211_tpt_led_trigger_flags - throughput trigger flags + * @IEEE80211_TPT_LEDTRIG_FL_RADIO: enable blinking with radio + * @IEEE80211_TPT_LEDTRIG_FL_WORK: enable blinking when working + * @IEEE80211_TPT_LEDTRIG_FL_CONNECTED: enable blinking when at least one + * interface is connected in some way, including being an AP + */ +enum ieee80211_tpt_led_trigger_flags { + IEEE80211_TPT_LEDTRIG_FL_RADIO = BIT(0), + IEEE80211_TPT_LEDTRIG_FL_WORK = BIT(1), + IEEE80211_TPT_LEDTRIG_FL_CONNECTED = BIT(2), +}; + #ifdef CONFIG_MAC80211_LEDS -extern char *__ieee80211_get_tx_led_name(struct ieee80211_hw *hw); -extern char *__ieee80211_get_rx_led_name(struct ieee80211_hw *hw); -extern char *__ieee80211_get_assoc_led_name(struct ieee80211_hw *hw); -extern char *__ieee80211_get_radio_led_name(struct ieee80211_hw *hw); +char *__ieee80211_get_tx_led_name(struct ieee80211_hw *hw); +char *__ieee80211_get_rx_led_name(struct ieee80211_hw *hw); +char *__ieee80211_get_assoc_led_name(struct ieee80211_hw *hw); +char *__ieee80211_get_radio_led_name(struct ieee80211_hw *hw); +char *__ieee80211_create_tpt_led_trigger(struct ieee80211_hw *hw, + unsigned int flags, + const struct ieee80211_tpt_blink *blink_table, + unsigned int blink_table_len); #endif /** * ieee80211_get_tx_led_name - get name of TX LED @@ -1867,6 +3088,8 @@ extern char *__ieee80211_get_radio_led_name(struct ieee80211_hw *hw); * of the trigger so you can automatically link the LED device. * * @hw: the hardware to get the LED trigger name for + * + * Return: The name of the LED trigger. %NULL if not configured for LEDs. */ static inline char *ieee80211_get_tx_led_name(struct ieee80211_hw *hw) { @@ -1886,6 +3109,8 @@ static inline char *ieee80211_get_tx_led_name(struct ieee80211_hw *hw) * of the trigger so you can automatically link the LED device. * * @hw: the hardware to get the LED trigger name for + * + * Return: The name of the LED trigger. %NULL if not configured for LEDs. */ static inline char *ieee80211_get_rx_led_name(struct ieee80211_hw *hw) { @@ -1905,6 +3130,8 @@ static inline char *ieee80211_get_rx_led_name(struct ieee80211_hw *hw) * of the trigger so you can automatically link the LED device. * * @hw: the hardware to get the LED trigger name for + * + * Return: The name of the LED trigger. %NULL if not configured for LEDs. */ static inline char *ieee80211_get_assoc_led_name(struct ieee80211_hw *hw) { @@ -1924,6 +3151,8 @@ static inline char *ieee80211_get_assoc_led_name(struct ieee80211_hw *hw) * of the trigger so you can automatically link the LED device. * * @hw: the hardware to get the LED trigger name for + * + * Return: The name of the LED trigger. %NULL if not configured for LEDs. */ static inline char *ieee80211_get_radio_led_name(struct ieee80211_hw *hw) { @@ -1935,6 +3164,31 @@ static inline char *ieee80211_get_radio_led_name(struct ieee80211_hw *hw) } /** + * ieee80211_create_tpt_led_trigger - create throughput LED trigger + * @hw: the hardware to create the trigger for + * @flags: trigger flags, see &enum ieee80211_tpt_led_trigger_flags + * @blink_table: the blink table -- needs to be ordered by throughput + * @blink_table_len: size of the blink table + * + * Return: %NULL (in case of error, or if no LED triggers are + * configured) or the name of the new trigger. + * + * Note: This function must be called before ieee80211_register_hw(). + */ +static inline char * +ieee80211_create_tpt_led_trigger(struct ieee80211_hw *hw, unsigned int flags, + const struct ieee80211_tpt_blink *blink_table, + unsigned int blink_table_len) +{ +#ifdef CONFIG_MAC80211_LEDS + return __ieee80211_create_tpt_led_trigger(hw, flags, blink_table, + blink_table_len); +#else + return NULL; +#endif +} + +/** * ieee80211_unregister_hw - Unregister a hardware device * * This function instructs mac80211 to free allocated resources @@ -1969,21 +3223,21 @@ void ieee80211_free_hw(struct ieee80211_hw *hw); */ void ieee80211_restart_hw(struct ieee80211_hw *hw); -/** ieee80211_napi_schedule - schedule NAPI poll - * - * Use this function to schedule NAPI polling on a device. - * - * @hw: the hardware to start polling - */ -void ieee80211_napi_schedule(struct ieee80211_hw *hw); - -/** ieee80211_napi_complete - complete NAPI polling - * - * Use this function to finish NAPI polling on a device. - * - * @hw: the hardware to stop polling +/** + * ieee80211_napi_add - initialize mac80211 NAPI context + * @hw: the hardware to initialize the NAPI context on + * @napi: the NAPI context to initialize + * @napi_dev: dummy NAPI netdevice, here to not waste the space if the + * driver doesn't use NAPI + * @poll: poll function + * @weight: default weight + * + * See also netif_napi_add(). */ -void ieee80211_napi_complete(struct ieee80211_hw *hw); +void ieee80211_napi_add(struct ieee80211_hw *hw, struct napi_struct *napi, + struct net_device *napi_dev, + int (*poll)(struct napi_struct *, int), + int weight); /** * ieee80211_rx - receive frame @@ -1997,7 +3251,8 @@ void ieee80211_napi_complete(struct ieee80211_hw *hw); * This function may not be called in IRQ context. Calls to this function * for a single hardware must be synchronized against each other. Calls to * this function, ieee80211_rx_ni() and ieee80211_rx_irqsafe() may not be - * mixed for a single hardware. + * mixed for a single hardware. Must not run concurrently with + * ieee80211_tx_status() or ieee80211_tx_status_ni(). * * In process context use instead ieee80211_rx_ni(). * @@ -2013,7 +3268,8 @@ void ieee80211_rx(struct ieee80211_hw *hw, struct sk_buff *skb); * (internally defers to a tasklet.) * * Calls to this function, ieee80211_rx() or ieee80211_rx_ni() may not - * be mixed for a single hardware. + * be mixed for a single hardware.Must not run concurrently with + * ieee80211_tx_status() or ieee80211_tx_status_ni(). * * @hw: the hardware this frame came in on * @skb: the buffer to receive, owned by mac80211 after this call @@ -2027,7 +3283,8 @@ void ieee80211_rx_irqsafe(struct ieee80211_hw *hw, struct sk_buff *skb); * (internally disables bottom halves). * * Calls to this function, ieee80211_rx() and ieee80211_rx_irqsafe() may - * not be mixed for a single hardware. + * not be mixed for a single hardware. Must not run concurrently with + * ieee80211_tx_status() or ieee80211_tx_status_ni(). * * @hw: the hardware this frame came in on * @skb: the buffer to receive, owned by mac80211 after this call @@ -2040,11 +3297,105 @@ static inline void ieee80211_rx_ni(struct ieee80211_hw *hw, local_bh_enable(); } +/** + * ieee80211_sta_ps_transition - PS transition for connected sta + * + * When operating in AP mode with the %IEEE80211_HW_AP_LINK_PS + * flag set, use this function to inform mac80211 about a connected station + * entering/leaving PS mode. + * + * This function may not be called in IRQ context or with softirqs enabled. + * + * Calls to this function for a single hardware must be synchronized against + * each other. + * + * @sta: currently connected sta + * @start: start or stop PS + * + * Return: 0 on success. -EINVAL when the requested PS mode is already set. + */ +int ieee80211_sta_ps_transition(struct ieee80211_sta *sta, bool start); + +/** + * ieee80211_sta_ps_transition_ni - PS transition for connected sta + * (in process context) + * + * Like ieee80211_sta_ps_transition() but can be called in process context + * (internally disables bottom halves). Concurrent call restriction still + * applies. + * + * @sta: currently connected sta + * @start: start or stop PS + * + * Return: Like ieee80211_sta_ps_transition(). + */ +static inline int ieee80211_sta_ps_transition_ni(struct ieee80211_sta *sta, + bool start) +{ + int ret; + + local_bh_disable(); + ret = ieee80211_sta_ps_transition(sta, start); + local_bh_enable(); + + return ret; +} + /* * The TX headroom reserved by mac80211 for its own tx_status functions. * This is enough for the radiotap header. */ -#define IEEE80211_TX_STATUS_HEADROOM 13 +#define IEEE80211_TX_STATUS_HEADROOM 14 + +/** + * ieee80211_sta_set_buffered - inform mac80211 about driver-buffered frames + * @sta: &struct ieee80211_sta pointer for the sleeping station + * @tid: the TID that has buffered frames + * @buffered: indicates whether or not frames are buffered for this TID + * + * If a driver buffers frames for a powersave station instead of passing + * them back to mac80211 for retransmission, the station may still need + * to be told that there are buffered frames via the TIM bit. + * + * This function informs mac80211 whether or not there are frames that are + * buffered in the driver for a given TID; mac80211 can then use this data + * to set the TIM bit (NOTE: This may call back into the driver's set_tim + * call! Beware of the locking!) + * + * If all frames are released to the station (due to PS-poll or uAPSD) + * then the driver needs to inform mac80211 that there no longer are + * frames buffered. However, when the station wakes up mac80211 assumes + * that all buffered frames will be transmitted and clears this data, + * drivers need to make sure they inform mac80211 about all buffered + * frames on the sleep transition (sta_notify() with %STA_NOTIFY_SLEEP). + * + * Note that technically mac80211 only needs to know this per AC, not per + * TID, but since driver buffering will inevitably happen per TID (since + * it is related to aggregation) it is easier to make mac80211 map the + * TID to the AC as required instead of keeping track in all drivers that + * use this API. + */ +void ieee80211_sta_set_buffered(struct ieee80211_sta *sta, + u8 tid, bool buffered); + +/** + * ieee80211_get_tx_rates - get the selected transmit rates for a packet + * + * Call this function in a driver with per-packet rate selection support + * to combine the rate info in the packet tx info with the most recent + * rate selection table for the station entry. + * + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * @sta: the receiver station to which this packet is sent. + * @skb: the frame to be transmitted. + * @dest: buffer for extracted rate/retry information + * @max_rates: maximum number of rates to fetch + */ +void ieee80211_get_tx_rates(struct ieee80211_vif *vif, + struct ieee80211_sta *sta, + struct sk_buff *skb, + struct ieee80211_tx_rate *dest, + int max_rates); /** * ieee80211_tx_status - transmit status callback @@ -2055,8 +3406,9 @@ static inline void ieee80211_rx_ni(struct ieee80211_hw *hw, * * This function may not be called in IRQ context. Calls to this function * for a single hardware must be synchronized against each other. Calls - * to this function and ieee80211_tx_status_irqsafe() may not be mixed - * for a single hardware. + * to this function, ieee80211_tx_status_ni() and ieee80211_tx_status_irqsafe() + * may not be mixed for a single hardware. Must not run concurrently with + * ieee80211_rx() or ieee80211_rx_ni(). * * @hw: the hardware the frame was transmitted by * @skb: the frame that was transmitted, owned by mac80211 after this call @@ -2065,13 +3417,33 @@ void ieee80211_tx_status(struct ieee80211_hw *hw, struct sk_buff *skb); /** + * ieee80211_tx_status_ni - transmit status callback (in process context) + * + * Like ieee80211_tx_status() but can be called in process context. + * + * Calls to this function, ieee80211_tx_status() and + * ieee80211_tx_status_irqsafe() may not be mixed + * for a single hardware. + * + * @hw: the hardware the frame was transmitted by + * @skb: the frame that was transmitted, owned by mac80211 after this call + */ +static inline void ieee80211_tx_status_ni(struct ieee80211_hw *hw, + struct sk_buff *skb) +{ + local_bh_disable(); + ieee80211_tx_status(hw, skb); + local_bh_enable(); +} + +/** * ieee80211_tx_status_irqsafe - IRQ-safe transmit status callback * * Like ieee80211_tx_status() but can be called in IRQ context * (internally defers to a tasklet.) * - * Calls to this function and ieee80211_tx_status() may not be mixed for a - * single hardware. + * Calls to this function, ieee80211_tx_status() and + * ieee80211_tx_status_ni() may not be mixed for a single hardware. * * @hw: the hardware the frame was transmitted by * @skb: the frame that was transmitted, owned by mac80211 after this call @@ -2080,6 +3452,58 @@ void ieee80211_tx_status_irqsafe(struct ieee80211_hw *hw, struct sk_buff *skb); /** + * ieee80211_report_low_ack - report non-responding station + * + * When operating in AP-mode, call this function to report a non-responding + * connected STA. + * + * @sta: the non-responding connected sta + * @num_packets: number of packets sent to @sta without a response + */ +void ieee80211_report_low_ack(struct ieee80211_sta *sta, u32 num_packets); + +#define IEEE80211_MAX_CSA_COUNTERS_NUM 2 + +/** + * struct ieee80211_mutable_offsets - mutable beacon offsets + * @tim_offset: position of TIM element + * @tim_length: size of TIM element + * @csa_counter_offs: array of IEEE80211_MAX_CSA_COUNTERS_NUM offsets + * to CSA counters. This array can contain zero values which + * should be ignored. + */ +struct ieee80211_mutable_offsets { + u16 tim_offset; + u16 tim_length; + + u16 csa_counter_offs[IEEE80211_MAX_CSA_COUNTERS_NUM]; +}; + +/** + * ieee80211_beacon_get_template - beacon template generation function + * @hw: pointer obtained from ieee80211_alloc_hw(). + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * @offs: &struct ieee80211_mutable_offsets pointer to struct that will + * receive the offsets that may be updated by the driver. + * + * If the driver implements beaconing modes, it must use this function to + * obtain the beacon template. + * + * This function should be used if the beacon frames are generated by the + * device, and then the driver must use the returned beacon as the template + * The driver or the device are responsible to update the DTIM and, when + * applicable, the CSA count. + * + * The driver is responsible for freeing the returned skb. + * + * Return: The beacon template. %NULL on error. + */ +struct sk_buff * +ieee80211_beacon_get_template(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct ieee80211_mutable_offsets *offs); + +/** * ieee80211_beacon_get_tim - beacon generation function * @hw: pointer obtained from ieee80211_alloc_hw(). * @vif: &struct ieee80211_vif pointer from the add_interface callback. @@ -2090,18 +3514,16 @@ void ieee80211_tx_status_irqsafe(struct ieee80211_hw *hw, * Set to 0 if invalid (in non-AP modes). * * If the driver implements beaconing modes, it must use this function to - * obtain the beacon frame/template. + * obtain the beacon frame. * * If the beacon frames are generated by the host system (i.e., not in * hardware/firmware), the driver uses this function to get each beacon - * frame from mac80211 -- it is responsible for calling this function - * before the beacon is needed (e.g. based on hardware interrupt). - * - * If the beacon frames are generated by the device, then the driver - * must use the returned beacon as the template and change the TIM IE - * according to the current DTIM parameters/TIM bitmap. + * frame from mac80211 -- it is responsible for calling this function exactly + * once before the beacon is needed (e.g. based on hardware interrupt). * * The driver is responsible for freeing the returned skb. + * + * Return: The beacon template. %NULL on error. */ struct sk_buff *ieee80211_beacon_get_tim(struct ieee80211_hw *hw, struct ieee80211_vif *vif, @@ -2113,6 +3535,8 @@ struct sk_buff *ieee80211_beacon_get_tim(struct ieee80211_hw *hw, * @vif: &struct ieee80211_vif pointer from the add_interface callback. * * See ieee80211_beacon_get_tim(). + * + * Return: See ieee80211_beacon_get_tim(). */ static inline struct sk_buff *ieee80211_beacon_get(struct ieee80211_hw *hw, struct ieee80211_vif *vif) @@ -2121,6 +3545,54 @@ static inline struct sk_buff *ieee80211_beacon_get(struct ieee80211_hw *hw, } /** + * ieee80211_csa_update_counter - request mac80211 to decrement the csa counter + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * + * The csa counter should be updated after each beacon transmission. + * This function is called implicitly when + * ieee80211_beacon_get/ieee80211_beacon_get_tim are called, however if the + * beacon frames are generated by the device, the driver should call this + * function after each beacon transmission to sync mac80211's csa counters. + * + * Return: new csa counter value + */ +u8 ieee80211_csa_update_counter(struct ieee80211_vif *vif); + +/** + * ieee80211_csa_finish - notify mac80211 about channel switch + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * + * After a channel switch announcement was scheduled and the counter in this + * announcement hits 1, this function must be called by the driver to + * notify mac80211 that the channel can be changed. + */ +void ieee80211_csa_finish(struct ieee80211_vif *vif); + +/** + * ieee80211_csa_is_complete - find out if counters reached 1 + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * + * This function returns whether the channel switch counters reached zero. + */ +bool ieee80211_csa_is_complete(struct ieee80211_vif *vif); + + +/** + * ieee80211_proberesp_get - retrieve a Probe Response template + * @hw: pointer obtained from ieee80211_alloc_hw(). + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * + * Creates a Probe Response template which can, for example, be uploaded to + * hardware. The destination address should be set by the caller. + * + * Can only be called in AP mode. + * + * Return: The Probe Response template. %NULL on error. + */ +struct sk_buff *ieee80211_proberesp_get(struct ieee80211_hw *hw, + struct ieee80211_vif *vif); + +/** * ieee80211_pspoll_get - retrieve a PS Poll template * @hw: pointer obtained from ieee80211_alloc_hw(). * @vif: &struct ieee80211_vif pointer from the add_interface callback. @@ -2131,6 +3603,8 @@ static inline struct sk_buff *ieee80211_beacon_get(struct ieee80211_hw *hw, * * Note: Caller (or hardware) is responsible for setting the * &IEEE80211_FCTL_PM bit. + * + * Return: The PS Poll template. %NULL on error. */ struct sk_buff *ieee80211_pspoll_get(struct ieee80211_hw *hw, struct ieee80211_vif *vif); @@ -2146,6 +3620,8 @@ struct sk_buff *ieee80211_pspoll_get(struct ieee80211_hw *hw, * * Note: Caller (or hardware) is responsible for setting the * &IEEE80211_FCTL_PM bit as well as Duration and Sequence Control fields. + * + * Return: The nullfunc template. %NULL on error. */ struct sk_buff *ieee80211_nullfunc_get(struct ieee80211_hw *hw, struct ieee80211_vif *vif); @@ -2156,16 +3632,17 @@ struct sk_buff *ieee80211_nullfunc_get(struct ieee80211_hw *hw, * @vif: &struct ieee80211_vif pointer from the add_interface callback. * @ssid: SSID buffer * @ssid_len: length of SSID - * @ie: buffer containing all IEs except SSID for the template - * @ie_len: length of the IE buffer + * @tailroom: tailroom to reserve at end of SKB for IEs * * Creates a Probe Request template which can, for example, be uploaded to * hardware. + * + * Return: The Probe Request template. %NULL on error. */ struct sk_buff *ieee80211_probereq_get(struct ieee80211_hw *hw, struct ieee80211_vif *vif, const u8 *ssid, size_t ssid_len, - const u8 *ie, size_t ie_len); + size_t tailroom); /** * ieee80211_rts_get - RTS frame generation function @@ -2196,6 +3673,8 @@ void ieee80211_rts_get(struct ieee80211_hw *hw, struct ieee80211_vif *vif, * If the RTS is generated in firmware, but the host system must provide * the duration field, the low-level driver uses this function to receive * the duration field value in little-endian byteorder. + * + * Return: The duration. */ __le16 ieee80211_rts_duration(struct ieee80211_hw *hw, struct ieee80211_vif *vif, size_t frame_len, @@ -2231,6 +3710,8 @@ void ieee80211_ctstoself_get(struct ieee80211_hw *hw, * If the CTS-to-self is generated in firmware, but the host system must provide * the duration field, the low-level driver uses this function to receive * the duration field value in little-endian byteorder. + * + * Return: The duration. */ __le16 ieee80211_ctstoself_duration(struct ieee80211_hw *hw, struct ieee80211_vif *vif, @@ -2241,14 +3722,18 @@ __le16 ieee80211_ctstoself_duration(struct ieee80211_hw *hw, * ieee80211_generic_frame_duration - Calculate the duration field for a frame * @hw: pointer obtained from ieee80211_alloc_hw(). * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * @band: the band to calculate the frame duration on * @frame_len: the length of the frame. * @rate: the rate at which the frame is going to be transmitted. * * Calculate the duration field of some generic frame, given its * length and transmission rate (in 100kbps). + * + * Return: The duration. */ __le16 ieee80211_generic_frame_duration(struct ieee80211_hw *hw, struct ieee80211_vif *vif, + enum ieee80211_band band, size_t frame_len, struct ieee80211_rate *rate); @@ -2261,9 +3746,10 @@ __le16 ieee80211_generic_frame_duration(struct ieee80211_hw *hw, * hardware/firmware does not implement buffering of broadcast/multicast * frames when power saving is used, 802.11 code buffers them in the host * memory. The low-level driver uses this function to fetch next buffered - * frame. In most cases, this is used when generating beacon frame. This - * function returns a pointer to the next buffered skb or NULL if no more - * buffered frames are available. + * frame. In most cases, this is used when generating beacon frame. + * + * Return: A pointer to the next buffered skb or NULL if no more buffered + * frames are available. * * Note: buffered frames are returned only after DTIM beacon frame was * generated with ieee80211_beacon_get() and the low-level driver must thus @@ -2276,21 +3762,232 @@ struct sk_buff * ieee80211_get_buffered_bc(struct ieee80211_hw *hw, struct ieee80211_vif *vif); /** - * ieee80211_get_tkip_key - get a TKIP rc4 for skb + * ieee80211_get_tkip_p1k_iv - get a TKIP phase 1 key for IV32 + * + * This function returns the TKIP phase 1 key for the given IV32. + * + * @keyconf: the parameter passed with the set key + * @iv32: IV32 to get the P1K for + * @p1k: a buffer to which the key will be written, as 5 u16 values + */ +void ieee80211_get_tkip_p1k_iv(struct ieee80211_key_conf *keyconf, + u32 iv32, u16 *p1k); + +/** + * ieee80211_get_tkip_p1k - get a TKIP phase 1 key * - * This function computes a TKIP rc4 key for an skb. It computes - * a phase 1 key if needed (iv16 wraps around). This function is to - * be used by drivers which can do HW encryption but need to compute - * to phase 1/2 key in SW. + * This function returns the TKIP phase 1 key for the IV32 taken + * from the given packet. * * @keyconf: the parameter passed with the set key - * @skb: the skb for which the key is needed - * @type: TBD - * @key: a buffer to which the key will be written + * @skb: the packet to take the IV32 value from that will be encrypted + * with this P1K + * @p1k: a buffer to which the key will be written, as 5 u16 values + */ +static inline void ieee80211_get_tkip_p1k(struct ieee80211_key_conf *keyconf, + struct sk_buff *skb, u16 *p1k) +{ + struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data; + const u8 *data = (u8 *)hdr + ieee80211_hdrlen(hdr->frame_control); + u32 iv32 = get_unaligned_le32(&data[4]); + + ieee80211_get_tkip_p1k_iv(keyconf, iv32, p1k); +} + +/** + * ieee80211_get_tkip_rx_p1k - get a TKIP phase 1 key for RX + * + * This function returns the TKIP phase 1 key for the given IV32 + * and transmitter address. + * + * @keyconf: the parameter passed with the set key + * @ta: TA that will be used with the key + * @iv32: IV32 to get the P1K for + * @p1k: a buffer to which the key will be written, as 5 u16 values + */ +void ieee80211_get_tkip_rx_p1k(struct ieee80211_key_conf *keyconf, + const u8 *ta, u32 iv32, u16 *p1k); + +/** + * ieee80211_get_tkip_p2k - get a TKIP phase 2 key + * + * This function computes the TKIP RC4 key for the IV values + * in the packet. + * + * @keyconf: the parameter passed with the set key + * @skb: the packet to take the IV32/IV16 values from that will be + * encrypted with this key + * @p2k: a buffer to which the key will be written, 16 bytes + */ +void ieee80211_get_tkip_p2k(struct ieee80211_key_conf *keyconf, + struct sk_buff *skb, u8 *p2k); + +/** + * ieee80211_aes_cmac_calculate_k1_k2 - calculate the AES-CMAC sub keys + * + * This function computes the two AES-CMAC sub-keys, based on the + * previously installed master key. + * + * @keyconf: the parameter passed with the set key + * @k1: a buffer to be filled with the 1st sub-key + * @k2: a buffer to be filled with the 2nd sub-key + */ +void ieee80211_aes_cmac_calculate_k1_k2(struct ieee80211_key_conf *keyconf, + u8 *k1, u8 *k2); + +/** + * struct ieee80211_key_seq - key sequence counter + * + * @tkip: TKIP data, containing IV32 and IV16 in host byte order + * @ccmp: PN data, most significant byte first (big endian, + * reverse order than in packet) + * @aes_cmac: PN data, most significant byte first (big endian, + * reverse order than in packet) + */ +struct ieee80211_key_seq { + union { + struct { + u32 iv32; + u16 iv16; + } tkip; + struct { + u8 pn[6]; + } ccmp; + struct { + u8 pn[6]; + } aes_cmac; + }; +}; + +/** + * ieee80211_get_key_tx_seq - get key TX sequence counter + * + * @keyconf: the parameter passed with the set key + * @seq: buffer to receive the sequence data + * + * This function allows a driver to retrieve the current TX IV/PN + * for the given key. It must not be called if IV generation is + * offloaded to the device. + * + * Note that this function may only be called when no TX processing + * can be done concurrently, for example when queues are stopped + * and the stop has been synchronized. + */ +void ieee80211_get_key_tx_seq(struct ieee80211_key_conf *keyconf, + struct ieee80211_key_seq *seq); + +/** + * ieee80211_get_key_rx_seq - get key RX sequence counter + * + * @keyconf: the parameter passed with the set key + * @tid: The TID, or -1 for the management frame value (CCMP only); + * the value on TID 0 is also used for non-QoS frames. For + * CMAC, only TID 0 is valid. + * @seq: buffer to receive the sequence data + * + * This function allows a driver to retrieve the current RX IV/PNs + * for the given key. It must not be called if IV checking is done + * by the device and not by mac80211. + * + * Note that this function may only be called when no RX processing + * can be done concurrently. + */ +void ieee80211_get_key_rx_seq(struct ieee80211_key_conf *keyconf, + int tid, struct ieee80211_key_seq *seq); + +/** + * ieee80211_set_key_tx_seq - set key TX sequence counter + * + * @keyconf: the parameter passed with the set key + * @seq: new sequence data + * + * This function allows a driver to set the current TX IV/PNs for the + * given key. This is useful when resuming from WoWLAN sleep and the + * device may have transmitted frames using the PTK, e.g. replies to + * ARP requests. + * + * Note that this function may only be called when no TX processing + * can be done concurrently. + */ +void ieee80211_set_key_tx_seq(struct ieee80211_key_conf *keyconf, + struct ieee80211_key_seq *seq); + +/** + * ieee80211_set_key_rx_seq - set key RX sequence counter + * + * @keyconf: the parameter passed with the set key + * @tid: The TID, or -1 for the management frame value (CCMP only); + * the value on TID 0 is also used for non-QoS frames. For + * CMAC, only TID 0 is valid. + * @seq: new sequence data + * + * This function allows a driver to set the current RX IV/PNs for the + * given key. This is useful when resuming from WoWLAN sleep and GTK + * rekey may have been done while suspended. It should not be called + * if IV checking is done by the device and not by mac80211. + * + * Note that this function may only be called when no RX processing + * can be done concurrently. + */ +void ieee80211_set_key_rx_seq(struct ieee80211_key_conf *keyconf, + int tid, struct ieee80211_key_seq *seq); + +/** + * ieee80211_remove_key - remove the given key + * @keyconf: the parameter passed with the set key + * + * Remove the given key. If the key was uploaded to the hardware at the + * time this function is called, it is not deleted in the hardware but + * instead assumed to have been removed already. + * + * Note that due to locking considerations this function can (currently) + * only be called during key iteration (ieee80211_iter_keys().) + */ +void ieee80211_remove_key(struct ieee80211_key_conf *keyconf); + +/** + * ieee80211_gtk_rekey_add - add a GTK key from rekeying during WoWLAN + * @vif: the virtual interface to add the key on + * @keyconf: new key data + * + * When GTK rekeying was done while the system was suspended, (a) new + * key(s) will be available. These will be needed by mac80211 for proper + * RX processing, so this function allows setting them. + * + * The function returns the newly allocated key structure, which will + * have similar contents to the passed key configuration but point to + * mac80211-owned memory. In case of errors, the function returns an + * ERR_PTR(), use IS_ERR() etc. + * + * Note that this function assumes the key isn't added to hardware + * acceleration, so no TX will be done with the key. Since it's a GTK + * on managed (station) networks, this is true anyway. If the driver + * calls this function from the resume callback and subsequently uses + * the return code 1 to reconfigure the device, this key will be part + * of the reconfiguration. + * + * Note that the driver should also call ieee80211_set_key_rx_seq() + * for the new key for each TID to set up sequence counters properly. + * + * IMPORTANT: If this replaces a key that is present in the hardware, + * then it will attempt to remove it during this call. In many cases + * this isn't what you want, so call ieee80211_remove_key() first for + * the key that's being replaced. */ -void ieee80211_get_tkip_key(struct ieee80211_key_conf *keyconf, - struct sk_buff *skb, - enum ieee80211_tkip_key_type type, u8 *key); +struct ieee80211_key_conf * +ieee80211_gtk_rekey_add(struct ieee80211_vif *vif, + struct ieee80211_key_conf *keyconf); + +/** + * ieee80211_gtk_rekey_notify - notify userspace supplicant of rekeying + * @vif: virtual interface the rekeying was done on + * @bssid: The BSSID of the AP, for checking association + * @replay_ctr: the new replay counter after GTK rekeying + * @gfp: allocation flags + */ +void ieee80211_gtk_rekey_notify(struct ieee80211_vif *vif, const u8 *bssid, + const u8 *replay_ctr, gfp_t gfp); + /** * ieee80211_wake_queue - wake specific queue * @hw: pointer as obtained from ieee80211_alloc_hw(). @@ -2315,6 +4012,8 @@ void ieee80211_stop_queue(struct ieee80211_hw *hw, int queue); * @queue: queue number (counted from zero). * * Drivers should use this function instead of netif_stop_queue. + * + * Return: %true if the queue is stopped. %false otherwise. */ int ieee80211_queue_stopped(struct ieee80211_hw *hw, int queue); @@ -2349,6 +4048,43 @@ void ieee80211_wake_queues(struct ieee80211_hw *hw); void ieee80211_scan_completed(struct ieee80211_hw *hw, bool aborted); /** + * ieee80211_sched_scan_results - got results from scheduled scan + * + * When a scheduled scan is running, this function needs to be called by the + * driver whenever there are new scan results available. + * + * @hw: the hardware that is performing scheduled scans + */ +void ieee80211_sched_scan_results(struct ieee80211_hw *hw); + +/** + * ieee80211_sched_scan_stopped - inform that the scheduled scan has stopped + * + * When a scheduled scan is running, this function can be called by + * the driver if it needs to stop the scan to perform another task. + * Usual scenarios are drivers that cannot continue the scheduled scan + * while associating, for instance. + * + * @hw: the hardware that is performing scheduled scans + */ +void ieee80211_sched_scan_stopped(struct ieee80211_hw *hw); + +/** + * enum ieee80211_interface_iteration_flags - interface iteration flags + * @IEEE80211_IFACE_ITER_NORMAL: Iterate over all interfaces that have + * been added to the driver; However, note that during hardware + * reconfiguration (after restart_hw) it will iterate over a new + * interface and over all the existing interfaces even if they + * haven't been re-added to the driver yet. + * @IEEE80211_IFACE_ITER_RESUME_ALL: During resume, iterate over all + * interfaces, even if they haven't been re-added to the driver yet. + */ +enum ieee80211_interface_iteration_flags { + IEEE80211_IFACE_ITER_NORMAL = 0, + IEEE80211_IFACE_ITER_RESUME_ALL = BIT(0), +}; + +/** * ieee80211_iterate_active_interfaces - iterate active interfaces * * This function iterates over the interfaces associated with a given @@ -2356,13 +4092,15 @@ void ieee80211_scan_completed(struct ieee80211_hw *hw, bool aborted); * This function allows the iterator function to sleep, when the iterator * function is atomic @ieee80211_iterate_active_interfaces_atomic can * be used. - * Does not iterate over a new interface during add_interface() + * Does not iterate over a new interface during add_interface(). * * @hw: the hardware struct of which the interfaces should be iterated over + * @iter_flags: iteration flags, see &enum ieee80211_interface_iteration_flags * @iterator: the iterator function to call * @data: first argument of the iterator function */ void ieee80211_iterate_active_interfaces(struct ieee80211_hw *hw, + u32 iter_flags, void (*iterator)(void *data, u8 *mac, struct ieee80211_vif *vif), void *data); @@ -2374,19 +4112,40 @@ void ieee80211_iterate_active_interfaces(struct ieee80211_hw *hw, * hardware that are currently active and calls the callback for them. * This function requires the iterator callback function to be atomic, * if that is not desired, use @ieee80211_iterate_active_interfaces instead. - * Does not iterate over a new interface during add_interface() + * Does not iterate over a new interface during add_interface(). * * @hw: the hardware struct of which the interfaces should be iterated over + * @iter_flags: iteration flags, see &enum ieee80211_interface_iteration_flags * @iterator: the iterator function to call, cannot sleep * @data: first argument of the iterator function */ void ieee80211_iterate_active_interfaces_atomic(struct ieee80211_hw *hw, + u32 iter_flags, void (*iterator)(void *data, u8 *mac, struct ieee80211_vif *vif), void *data); /** + * ieee80211_iterate_active_interfaces_rtnl - iterate active interfaces + * + * This function iterates over the interfaces associated with a given + * hardware that are currently active and calls the callback for them. + * This version can only be used while holding the RTNL. + * + * @hw: the hardware struct of which the interfaces should be iterated over + * @iter_flags: iteration flags, see &enum ieee80211_interface_iteration_flags + * @iterator: the iterator function to call, cannot sleep + * @data: first argument of the iterator function + */ +void ieee80211_iterate_active_interfaces_rtnl(struct ieee80211_hw *hw, + u32 iter_flags, + void (*iterator)(void *data, + u8 *mac, + struct ieee80211_vif *vif), + void *data); + +/** * ieee80211_queue_work - add work onto the mac80211 workqueue * * Drivers and mac80211 use this to add work onto the mac80211 workqueue. @@ -2415,6 +4174,7 @@ void ieee80211_queue_delayed_work(struct ieee80211_hw *hw, * ieee80211_start_tx_ba_session - Start a tx Block Ack session. * @sta: the station for which to start a BA session * @tid: the TID to BA on. + * @timeout: session timeout value (in TUs) * * Return: success if addBA request was sent, failure otherwise * @@ -2422,7 +4182,8 @@ void ieee80211_queue_delayed_work(struct ieee80211_hw *hw, * the need to start aggregation on a certain RA/TID, the session level * will be managed by the mac80211. */ -int ieee80211_start_tx_ba_session(struct ieee80211_sta *sta, u16 tid); +int ieee80211_start_tx_ba_session(struct ieee80211_sta *sta, u16 tid, + u16 timeout); /** * ieee80211_start_tx_ba_cb_irqsafe - low level driver ready to aggregate. @@ -2469,7 +4230,9 @@ void ieee80211_stop_tx_ba_cb_irqsafe(struct ieee80211_vif *vif, const u8 *ra, * @vif: virtual interface to look for station on * @addr: station's address * - * This function must be called under RCU lock and the + * Return: The station, if found. %NULL otherwise. + * + * Note: This function must be called under RCU lock and the * resulting pointer is only valid under RCU lock as well. */ struct ieee80211_sta *ieee80211_find_sta(struct ieee80211_vif *vif, @@ -2482,7 +4245,9 @@ struct ieee80211_sta *ieee80211_find_sta(struct ieee80211_vif *vif, * @addr: remote station's address * @localaddr: local address (vif->sdata->vif.addr). Use NULL for 'any'. * - * This function must be called under RCU lock and the + * Return: The station, if found. %NULL otherwise. + * + * Note: This function must be called under RCU lock and the * resulting pointer is only valid under RCU lock as well. * * NOTE: You may pass NULL for localaddr, but then you will just get @@ -2532,6 +4297,80 @@ void ieee80211_sta_block_awake(struct ieee80211_hw *hw, struct ieee80211_sta *pubsta, bool block); /** + * ieee80211_sta_eosp - notify mac80211 about end of SP + * @pubsta: the station + * + * When a device transmits frames in a way that it can't tell + * mac80211 in the TX status about the EOSP, it must clear the + * %IEEE80211_TX_STATUS_EOSP bit and call this function instead. + * This applies for PS-Poll as well as uAPSD. + * + * Note that just like with _tx_status() and _rx() drivers must + * not mix calls to irqsafe/non-irqsafe versions, this function + * must not be mixed with those either. Use the all irqsafe, or + * all non-irqsafe, don't mix! + * + * NB: the _irqsafe version of this function doesn't exist, no + * driver needs it right now. Don't call this function if + * you'd need the _irqsafe version, look at the git history + * and restore the _irqsafe version! + */ +void ieee80211_sta_eosp(struct ieee80211_sta *pubsta); + +/** + * ieee80211_iter_keys - iterate keys programmed into the device + * @hw: pointer obtained from ieee80211_alloc_hw() + * @vif: virtual interface to iterate, may be %NULL for all + * @iter: iterator function that will be called for each key + * @iter_data: custom data to pass to the iterator function + * + * This function can be used to iterate all the keys known to + * mac80211, even those that weren't previously programmed into + * the device. This is intended for use in WoWLAN if the device + * needs reprogramming of the keys during suspend. Note that due + * to locking reasons, it is also only safe to call this at few + * spots since it must hold the RTNL and be able to sleep. + * + * The order in which the keys are iterated matches the order + * in which they were originally installed and handed to the + * set_key callback. + */ +void ieee80211_iter_keys(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + void (*iter)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct ieee80211_sta *sta, + struct ieee80211_key_conf *key, + void *data), + void *iter_data); + +/** + * ieee80211_iter_chan_contexts_atomic - iterate channel contexts + * @hw: pointre obtained from ieee80211_alloc_hw(). + * @iter: iterator function + * @iter_data: data passed to iterator function + * + * Iterate all active channel contexts. This function is atomic and + * doesn't acquire any locks internally that might be held in other + * places while calling into the driver. + * + * The iterator will not find a context that's being added (during + * the driver callback to add it) but will find it while it's being + * removed. + * + * Note that during hardware restart, all contexts that existed + * before the restart are considered already present so will be + * found while iterating, whether they've been re-added already + * or not. + */ +void ieee80211_iter_chan_contexts_atomic( + struct ieee80211_hw *hw, + void (*iter)(struct ieee80211_hw *hw, + struct ieee80211_chanctx_conf *chanctx_conf, + void *data), + void *iter_data); + +/** * ieee80211_ap_probereq_get - retrieve a Probe Request template * @hw: pointer obtained from ieee80211_alloc_hw(). * @vif: &struct ieee80211_vif pointer from the add_interface callback. @@ -2541,7 +4380,9 @@ void ieee80211_sta_block_awake(struct ieee80211_hw *hw, * information. This function must only be called from within the * .bss_info_changed callback function and only in managed mode. The function * is only useful when the interface is associated, otherwise it will return - * NULL. + * %NULL. + * + * Return: The Probe Request template. %NULL on error. */ struct sk_buff *ieee80211_ap_probereq_get(struct ieee80211_hw *hw, struct ieee80211_vif *vif); @@ -2551,7 +4392,7 @@ struct sk_buff *ieee80211_ap_probereq_get(struct ieee80211_hw *hw, * * @vif: &struct ieee80211_vif pointer from the add_interface callback. * - * When beacon filtering is enabled with %IEEE80211_HW_BEACON_FILTER and + * When beacon filtering is enabled with %IEEE80211_VIF_BEACON_FILTER and * %IEEE80211_CONF_PS is set, the driver needs to inform whenever the * hardware is not receiving beacons with this function. */ @@ -2562,9 +4403,11 @@ void ieee80211_beacon_loss(struct ieee80211_vif *vif); * * @vif: &struct ieee80211_vif pointer from the add_interface callback. * - * When beacon filtering is enabled with %IEEE80211_HW_BEACON_FILTER, and + * When beacon filtering is enabled with %IEEE80211_VIF_BEACON_FILTER, and * %IEEE80211_CONF_PS and %IEEE80211_HW_CONNECTION_MONITOR are set, the driver * needs to inform if the connection to the AP has been lost. + * The function may also be called if the connection needs to be terminated + * for some other reason, even if %IEEE80211_HW_CONNECTION_MONITOR isn't set. * * This function will cause immediate change to disassociated state, * without connection recovery attempts. @@ -2572,34 +4415,27 @@ void ieee80211_beacon_loss(struct ieee80211_vif *vif); void ieee80211_connection_loss(struct ieee80211_vif *vif); /** - * ieee80211_disable_dyn_ps - force mac80211 to temporarily disable dynamic psm + * ieee80211_resume_disconnect - disconnect from AP after resume * * @vif: &struct ieee80211_vif pointer from the add_interface callback. * - * Some hardware require full power save to manage simultaneous BT traffic - * on the WLAN frequency. Full PSM is required periodically, whenever there are - * burst of BT traffic. The hardware gets information of BT traffic via - * hardware co-existence lines, and consequentially requests mac80211 to - * (temporarily) enter full psm. - * This function will only temporarily disable dynamic PS, not enable PSM if - * it was not already enabled. - * The driver must make sure to re-enable dynamic PS using - * ieee80211_enable_dyn_ps() if the driver has disabled it. - * + * Instructs mac80211 to disconnect from the AP after resume. + * Drivers can use this after WoWLAN if they know that the + * connection cannot be kept up, for example because keys were + * used while the device was asleep but the replay counters or + * similar cannot be retrieved from the device during resume. + * + * Note that due to implementation issues, if the driver uses + * the reconfiguration functionality during resume the interface + * will still be added as associated first during resume and then + * disconnect normally later. + * + * This function can only be called from the resume callback and + * the driver must not be holding any of its own locks while it + * calls this function, or at least not any locks it needs in the + * key configuration paths (if it supports HW crypto). */ -void ieee80211_disable_dyn_ps(struct ieee80211_vif *vif); - -/** - * ieee80211_enable_dyn_ps - restore dynamic psm after being disabled - * - * @vif: &struct ieee80211_vif pointer from the add_interface callback. - * - * This function restores dynamic PS after being temporarily disabled via - * ieee80211_disable_dyn_ps(). Each ieee80211_disable_dyn_ps() call must - * be coupled with an eventual call to this function. - * - */ -void ieee80211_enable_dyn_ps(struct ieee80211_vif *vif); +void ieee80211_resume_disconnect(struct ieee80211_vif *vif); /** * ieee80211_cqm_rssi_notify - inform a configured connection quality monitoring @@ -2609,7 +4445,7 @@ void ieee80211_enable_dyn_ps(struct ieee80211_vif *vif); * @rssi_event: the RSSI trigger event type * @gfp: context flags * - * When the %IEEE80211_HW_SUPPORTS_CQM_RSSI is set, and a connection quality + * When the %IEEE80211_VIF_SUPPORTS_CQM_RSSI is set, and a connection quality * monitoring is configured with an rssi threshold, the driver will inform * whenever the rssi level reaches the threshold. */ @@ -2618,6 +4454,13 @@ void ieee80211_cqm_rssi_notify(struct ieee80211_vif *vif, gfp_t gfp); /** + * ieee80211_radar_detected - inform that a radar was detected + * + * @hw: pointer as obtained from ieee80211_alloc_hw() + */ +void ieee80211_radar_detected(struct ieee80211_hw *hw); + +/** * ieee80211_chswitch_done - Complete channel switch process * @vif: &struct ieee80211_vif pointer from the add_interface callback. * @success: make the channel switch successful or not @@ -2640,32 +4483,48 @@ void ieee80211_request_smps(struct ieee80211_vif *vif, enum ieee80211_smps_mode smps_mode); /** - * ieee80211_key_removed - disable hw acceleration for key - * @key_conf: The key hw acceleration should be disabled for + * ieee80211_ready_on_channel - notification of remain-on-channel start + * @hw: pointer as obtained from ieee80211_alloc_hw() + */ +void ieee80211_ready_on_channel(struct ieee80211_hw *hw); + +/** + * ieee80211_remain_on_channel_expired - remain_on_channel duration expired + * @hw: pointer as obtained from ieee80211_alloc_hw() + */ +void ieee80211_remain_on_channel_expired(struct ieee80211_hw *hw); + +/** + * ieee80211_stop_rx_ba_session - callback to stop existing BA sessions * - * This allows drivers to indicate that the given key has been - * removed from hardware acceleration, due to a new key that - * was added. Don't use this if the key can continue to be used - * for TX, if the key restriction is on RX only it is permitted - * to keep the key for TX only and not call this function. + * in order not to harm the system performance and user experience, the device + * may request not to allow any rx ba session and tear down existing rx ba + * sessions based on system constraints such as periodic BT activity that needs + * to limit wlan activity (eg.sco or a2dp)." + * in such cases, the intention is to limit the duration of the rx ppdu and + * therefore prevent the peer device to use a-mpdu aggregation. * - * Due to locking constraints, it may only be called during - * @set_key. This function must be allowed to sleep, and the - * key it tries to disable may still be used until it returns. + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * @ba_rx_bitmap: Bit map of open rx ba per tid + * @addr: & to bssid mac address */ -void ieee80211_key_removed(struct ieee80211_key_conf *key_conf); - -/* Rate control API */ +void ieee80211_stop_rx_ba_session(struct ieee80211_vif *vif, u16 ba_rx_bitmap, + const u8 *addr); /** - * enum rate_control_changed - flags to indicate which parameter changed + * ieee80211_send_bar - send a BlockAckReq frame + * + * can be used to flush pending frames from the peer's aggregation reorder + * buffer. * - * @IEEE80211_RC_HT_CHANGED: The HT parameters of the operating channel have - * changed, rate control algorithm can update its internal state if needed. + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * @ra: the peer's destination address + * @tid: the TID of the aggregation session + * @ssn: the new starting sequence number for the receiver */ -enum rate_control_changed { - IEEE80211_RC_HT_CHANGED = BIT(0) -}; +void ieee80211_send_bar(struct ieee80211_vif *vif, u8 *ra, u16 tid, u16 ssn); + +/* Rate control API */ /** * struct ieee80211_tx_rate_control - rate control information for/from RC algo @@ -2673,6 +4532,8 @@ enum rate_control_changed { * @hw: The hardware the algorithm is invoked for. * @sband: The band this frame is being transmitted on. * @bss_conf: the current BSS configuration + * @skb: the skb that will be transmitted, the control information in it needs + * to be filled in * @reported_rate: The rate control algorithm can fill this in to indicate * which rate should be reported to userspace as the current rate and * used for rate calculations in the mesh network. @@ -2680,12 +4541,11 @@ enum rate_control_changed { * RTS threshold * @short_preamble: whether mac80211 will request short-preamble transmission * if the selected rate supports it - * @max_rate_idx: user-requested maximum rate (not MCS for now) + * @max_rate_idx: user-requested maximum (legacy) rate * (deprecated; this will be removed once drivers get updated to use * rate_idx_mask) - * @rate_idx_mask: user-requested rate mask (not MCS for now) - * @skb: the skb that will be transmitted, the control information in it needs - * to be filled in + * @rate_idx_mask: user-requested (legacy) rate mask + * @rate_idx_mcs_mask: user-requested MCS rate mask (NULL if not in use) * @bss: whether this frame is sent out in AP or IBSS mode */ struct ieee80211_tx_rate_control { @@ -2697,22 +4557,23 @@ struct ieee80211_tx_rate_control { bool rts, short_preamble; u8 max_rate_idx; u32 rate_idx_mask; + u8 *rate_idx_mcs_mask; bool bss; }; struct rate_control_ops { - struct module *module; const char *name; void *(*alloc)(struct ieee80211_hw *hw, struct dentry *debugfsdir); void (*free)(void *priv); void *(*alloc_sta)(void *priv, struct ieee80211_sta *sta, gfp_t gfp); void (*rate_init)(void *priv, struct ieee80211_supported_band *sband, + struct cfg80211_chan_def *chandef, struct ieee80211_sta *sta, void *priv_sta); void (*rate_update)(void *priv, struct ieee80211_supported_band *sband, - struct ieee80211_sta *sta, - void *priv_sta, u32 changed, - enum nl80211_channel_type oper_chan_type); + struct cfg80211_chan_def *chandef, + struct ieee80211_sta *sta, void *priv_sta, + u32 changed); void (*free_sta)(void *priv, struct ieee80211_sta *sta, void *priv_sta); @@ -2725,6 +4586,8 @@ struct rate_control_ops { void (*add_sta_debugfs)(void *priv, void *priv_sta, struct dentry *dir); void (*remove_sta_debugfs)(void *priv, void *priv_sta); + + u32 (*get_expected_throughput)(void *priv_sta); }; static inline int rate_supported(struct ieee80211_sta *sta, @@ -2768,8 +4631,9 @@ rate_lowest_index(struct ieee80211_supported_band *sband, return i; /* warn when we cannot find a rate. */ - WARN_ON(1); + WARN_ON_ONCE(1); + /* and return 0 (the lowest index) */ return 0; } @@ -2785,37 +4649,57 @@ bool rate_usable_index_exists(struct ieee80211_supported_band *sband, return false; } -int ieee80211_rate_control_register(struct rate_control_ops *ops); -void ieee80211_rate_control_unregister(struct rate_control_ops *ops); +/** + * rate_control_set_rates - pass the sta rate selection to mac80211/driver + * + * When not doing a rate control probe to test rates, rate control should pass + * its rate selection to mac80211. If the driver supports receiving a station + * rate table, it will use it to ensure that frames are always sent based on + * the most recent rate control module decision. + * + * @hw: pointer as obtained from ieee80211_alloc_hw() + * @pubsta: &struct ieee80211_sta pointer to the target destination. + * @rates: new tx rate set to be used for this station. + */ +int rate_control_set_rates(struct ieee80211_hw *hw, + struct ieee80211_sta *pubsta, + struct ieee80211_sta_rates *rates); + +int ieee80211_rate_control_register(const struct rate_control_ops *ops); +void ieee80211_rate_control_unregister(const struct rate_control_ops *ops); static inline bool conf_is_ht20(struct ieee80211_conf *conf) { - return conf->channel_type == NL80211_CHAN_HT20; + return conf->chandef.width == NL80211_CHAN_WIDTH_20; } static inline bool conf_is_ht40_minus(struct ieee80211_conf *conf) { - return conf->channel_type == NL80211_CHAN_HT40MINUS; + return conf->chandef.width == NL80211_CHAN_WIDTH_40 && + conf->chandef.center_freq1 < conf->chandef.chan->center_freq; } static inline bool conf_is_ht40_plus(struct ieee80211_conf *conf) { - return conf->channel_type == NL80211_CHAN_HT40PLUS; + return conf->chandef.width == NL80211_CHAN_WIDTH_40 && + conf->chandef.center_freq1 > conf->chandef.chan->center_freq; } static inline bool conf_is_ht40(struct ieee80211_conf *conf) { - return conf_is_ht40_minus(conf) || conf_is_ht40_plus(conf); + return conf->chandef.width == NL80211_CHAN_WIDTH_40; } static inline bool conf_is_ht(struct ieee80211_conf *conf) { - return conf->channel_type != NL80211_CHAN_NO_HT; + return (conf->chandef.width != NL80211_CHAN_WIDTH_5) && + (conf->chandef.width != NL80211_CHAN_WIDTH_10) && + (conf->chandef.width != NL80211_CHAN_WIDTH_20_NOHT); } static inline enum nl80211_iftype @@ -2840,4 +4724,95 @@ ieee80211_vif_type_p2p(struct ieee80211_vif *vif) return ieee80211_iftype_p2p(vif->type, vif->p2p); } +void ieee80211_enable_rssi_reports(struct ieee80211_vif *vif, + int rssi_min_thold, + int rssi_max_thold); + +void ieee80211_disable_rssi_reports(struct ieee80211_vif *vif); + +/** + * ieee80211_ave_rssi - report the average RSSI for the specified interface + * + * @vif: the specified virtual interface + * + * Note: This function assumes that the given vif is valid. + * + * Return: The average RSSI value for the requested interface, or 0 if not + * applicable. + */ +int ieee80211_ave_rssi(struct ieee80211_vif *vif); + +/** + * ieee80211_report_wowlan_wakeup - report WoWLAN wakeup + * @vif: virtual interface + * @wakeup: wakeup reason(s) + * @gfp: allocation flags + * + * See cfg80211_report_wowlan_wakeup(). + */ +void ieee80211_report_wowlan_wakeup(struct ieee80211_vif *vif, + struct cfg80211_wowlan_wakeup *wakeup, + gfp_t gfp); + +/** + * ieee80211_tx_prepare_skb - prepare an 802.11 skb for transmission + * @hw: pointer as obtained from ieee80211_alloc_hw() + * @vif: virtual interface + * @skb: frame to be sent from within the driver + * @band: the band to transmit on + * @sta: optional pointer to get the station to send the frame to + * + * Note: must be called under RCU lock + */ +bool ieee80211_tx_prepare_skb(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, struct sk_buff *skb, + int band, struct ieee80211_sta **sta); + +/** + * struct ieee80211_noa_data - holds temporary data for tracking P2P NoA state + * + * @next_tsf: TSF timestamp of the next absent state change + * @has_next_tsf: next absent state change event pending + * + * @absent: descriptor bitmask, set if GO is currently absent + * + * private: + * + * @count: count fields from the NoA descriptors + * @desc: adjusted data from the NoA + */ +struct ieee80211_noa_data { + u32 next_tsf; + bool has_next_tsf; + + u8 absent; + + u8 count[IEEE80211_P2P_NOA_DESC_MAX]; + struct { + u32 start; + u32 duration; + u32 interval; + } desc[IEEE80211_P2P_NOA_DESC_MAX]; +}; + +/** + * ieee80211_parse_p2p_noa - initialize NoA tracking data from P2P IE + * + * @attr: P2P NoA IE + * @data: NoA tracking data + * @tsf: current TSF timestamp + * + * Return: number of successfully parsed descriptors + */ +int ieee80211_parse_p2p_noa(const struct ieee80211_p2p_noa_attr *attr, + struct ieee80211_noa_data *data, u32 tsf); + +/** + * ieee80211_update_p2p_noa - get next pending P2P GO absent state change + * + * @data: NoA tracking data + * @tsf: current TSF timestamp + */ +void ieee80211_update_p2p_noa(struct ieee80211_noa_data *data, u32 tsf); + #endif /* MAC80211_H */ |