diff options
Diffstat (limited to 'include/net/mac80211.h')
| -rw-r--r-- | include/net/mac80211.h | 460 |
1 files changed, 375 insertions, 85 deletions
diff --git a/include/net/mac80211.h b/include/net/mac80211.h index cc6035f1a2f..421b6ecb4b2 100644 --- a/include/net/mac80211.h +++ b/include/net/mac80211.h @@ -66,10 +66,6 @@ * * Secondly, when the hardware handles fragmentation, the frame handed to * the driver from mac80211 is the MSDU, not the MPDU. - * - * Finally, for received frames, the driver is able to indicate that it has - * filled a radiotap header and put that in front of the frame; if it does - * not do so then mac80211 may add this under certain circumstances. */ /** @@ -154,12 +150,14 @@ struct ieee80211_low_level_stats { * @IEEE80211_CHANCTX_CHANGE_RADAR: radar detection flag changed * @IEEE80211_CHANCTX_CHANGE_CHANNEL: switched to another operating channel, * this is used only with channel switching with CSA + * @IEEE80211_CHANCTX_CHANGE_MIN_WIDTH: The min required channel width changed */ enum ieee80211_chanctx_change { IEEE80211_CHANCTX_CHANGE_WIDTH = BIT(0), IEEE80211_CHANCTX_CHANGE_RX_CHAINS = BIT(1), IEEE80211_CHANCTX_CHANGE_RADAR = BIT(2), IEEE80211_CHANCTX_CHANGE_CHANNEL = BIT(3), + IEEE80211_CHANCTX_CHANGE_MIN_WIDTH = BIT(4), }; /** @@ -169,6 +167,7 @@ enum ieee80211_chanctx_change { * that contains it is visible in mac80211 only. * * @def: the channel definition + * @min_def: the minimum channel definition currently required. * @rx_chains_static: The number of RX chains that must always be * active on the channel to receive MIMO transmissions * @rx_chains_dynamic: The number of RX chains that must be enabled @@ -180,6 +179,7 @@ enum ieee80211_chanctx_change { */ struct ieee80211_chanctx_conf { struct cfg80211_chan_def def; + struct cfg80211_chan_def min_def; u8 rx_chains_static, rx_chains_dynamic; @@ -189,6 +189,43 @@ struct ieee80211_chanctx_conf { }; /** + * enum ieee80211_chanctx_switch_mode - channel context switch mode + * @CHANCTX_SWMODE_REASSIGN_VIF: Both old and new contexts already + * exist (and will continue to exist), but the virtual interface + * needs to be switched from one to the other. + * @CHANCTX_SWMODE_SWAP_CONTEXTS: The old context exists but will stop + * to exist with this call, the new context doesn't exist but + * will be active after this call, the virtual interface switches + * from the old to the new (note that the driver may of course + * implement this as an on-the-fly chandef switch of the existing + * hardware context, but the mac80211 pointer for the old context + * will cease to exist and only the new one will later be used + * for changes/removal.) + */ +enum ieee80211_chanctx_switch_mode { + CHANCTX_SWMODE_REASSIGN_VIF, + CHANCTX_SWMODE_SWAP_CONTEXTS, +}; + +/** + * struct ieee80211_vif_chanctx_switch - vif chanctx switch information + * + * This is structure is used to pass information about a vif that + * needs to switch from one chanctx to another. The + * &ieee80211_chanctx_switch_mode defines how the switch should be + * done. + * + * @vif: the vif that should be switched from old_ctx to new_ctx + * @old_ctx: the old context to which the vif was assigned + * @new_ctx: the new context to which the vif must be assigned + */ +struct ieee80211_vif_chanctx_switch { + struct ieee80211_vif *vif; + struct ieee80211_chanctx_conf *old_ctx; + struct ieee80211_chanctx_conf *new_ctx; +}; + +/** * enum ieee80211_bss_change - BSS change notification flags * * These flags are used with the bss_info_changed() callback @@ -697,11 +734,11 @@ struct ieee80211_tx_info { } control; struct { struct ieee80211_tx_rate rates[IEEE80211_TX_MAX_RATES]; - int ack_signal; + s32 ack_signal; u8 ampdu_ack_len; u8 ampdu_len; u8 antenna; - /* 21 bytes free */ + void *status_driver_data[21 / sizeof(void *)]; } status; struct { struct ieee80211_tx_rate driver_rates[ @@ -804,9 +841,6 @@ ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info) * @RX_FLAG_HT: HT MCS was used and rate_idx is MCS index * @RX_FLAG_VHT: VHT MCS was used and rate_index is MCS index * @RX_FLAG_40MHZ: HT40 (40 MHz) was used - * @RX_FLAG_80MHZ: 80 MHz was used - * @RX_FLAG_80P80MHZ: 80+80 MHz was used - * @RX_FLAG_160MHZ: 160 MHz was used * @RX_FLAG_SHORT_GI: Short guard interval was used * @RX_FLAG_NO_SIGNAL_VAL: The signal strength value is not present. * Valid only for data frames (mainly A-MPDU) @@ -826,9 +860,19 @@ ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info) * on this subframe * @RX_FLAG_AMPDU_DELIM_CRC_KNOWN: The delimiter CRC field is known (the CRC * is stored in the @ampdu_delimiter_crc field) + * @RX_FLAG_LDPC: LDPC was used * @RX_FLAG_STBC_MASK: STBC 2 bit bitmask. 1 - Nss=1, 2 - Nss=2, 3 - Nss=3 * @RX_FLAG_10MHZ: 10 MHz (half channel) was used * @RX_FLAG_5MHZ: 5 MHz (quarter channel) was used + * @RX_FLAG_AMSDU_MORE: Some drivers may prefer to report separate A-MSDU + * subframes instead of a one huge frame for performance reasons. + * All, but the last MSDU from an A-MSDU should have this flag set. E.g. + * if an A-MSDU has 3 frames, the first 2 must have the flag set, while + * the 3rd (last) one must not have this flag set. The flag is used to + * deal with retransmission/duplication recovery properly since A-MSDU + * subframes share the same sequence number. Reported subframes can be + * either regular MSDU or singly A-MSDUs. Subframes must not be + * interleaved with other frames. */ enum mac80211_rx_flags { RX_FLAG_MMIC_ERROR = BIT(0), @@ -853,17 +897,33 @@ enum mac80211_rx_flags { RX_FLAG_AMPDU_DELIM_CRC_KNOWN = BIT(20), RX_FLAG_MACTIME_END = BIT(21), RX_FLAG_VHT = BIT(22), - RX_FLAG_80MHZ = BIT(23), - RX_FLAG_80P80MHZ = BIT(24), - RX_FLAG_160MHZ = BIT(25), + RX_FLAG_LDPC = BIT(23), RX_FLAG_STBC_MASK = BIT(26) | BIT(27), RX_FLAG_10MHZ = BIT(28), RX_FLAG_5MHZ = BIT(29), + RX_FLAG_AMSDU_MORE = BIT(30), }; #define RX_FLAG_STBC_SHIFT 26 /** + * enum mac80211_rx_vht_flags - receive VHT flags + * + * These flags are used with the @vht_flag member of + * &struct ieee80211_rx_status. + * @RX_VHT_FLAG_80MHZ: 80 MHz was used + * @RX_VHT_FLAG_80P80MHZ: 80+80 MHz was used + * @RX_VHT_FLAG_160MHZ: 160 MHz was used + * @RX_VHT_FLAG_BF: packet was beamformed + */ +enum mac80211_rx_vht_flags { + RX_VHT_FLAG_80MHZ = BIT(0), + RX_VHT_FLAG_80P80MHZ = BIT(1), + RX_VHT_FLAG_160MHZ = BIT(2), + RX_VHT_FLAG_BF = BIT(3), +}; + +/** * struct ieee80211_rx_status - receive status * * The low-level driver should provide this information (the subset @@ -888,26 +948,19 @@ enum mac80211_rx_flags { * HT or VHT is used (%RX_FLAG_HT/%RX_FLAG_VHT) * @vht_nss: number of streams (VHT only) * @flag: %RX_FLAG_* + * @vht_flag: %RX_VHT_FLAG_* * @rx_flags: internal RX flags for mac80211 * @ampdu_reference: A-MPDU reference number, must be a different value for * each A-MPDU but the same for each subframe within one A-MPDU * @ampdu_delimiter_crc: A-MPDU delimiter CRC - * @vendor_radiotap_bitmap: radiotap vendor namespace presence bitmap - * @vendor_radiotap_len: radiotap vendor namespace length - * @vendor_radiotap_align: radiotap vendor namespace alignment. Note - * that the actual data must be at the start of the SKB data - * already. - * @vendor_radiotap_oui: radiotap vendor namespace OUI - * @vendor_radiotap_subns: radiotap vendor sub namespace */ struct ieee80211_rx_status { u64 mactime; u32 device_timestamp; u32 ampdu_reference; u32 flag; - u32 vendor_radiotap_bitmap; - u16 vendor_radiotap_len; u16 freq; + u8 vht_flag; u8 rate_idx; u8 vht_nss; u8 rx_flags; @@ -917,9 +970,6 @@ struct ieee80211_rx_status { u8 chains; s8 chain_signal[IEEE80211_MAX_CHAINS]; u8 ampdu_delimiter_crc; - u8 vendor_radiotap_align; - u8 vendor_radiotap_oui[3]; - u8 vendor_radiotap_subns; }; /** @@ -1100,7 +1150,9 @@ enum ieee80211_vif_flags { * @addr: address of this interface * @p2p: indicates whether this AP or STA interface is a p2p * interface, i.e. a GO or p2p-sta respectively - * @csa_active: marks whether a channel switch is going on + * @csa_active: marks whether a channel switch is going on. Internally it is + * write-protected by sdata_lock and local->mtx so holding either is fine + * for read access. * @driver_flags: flags/capabilities the driver has for this interface, * these need to be set (or cleared) when the interface is added * or, if supported by the driver, the interface type is changed @@ -1149,6 +1201,19 @@ static inline bool ieee80211_vif_is_mesh(struct ieee80211_vif *vif) } /** + * wdev_to_ieee80211_vif - return a vif struct from a wdev + * @wdev: the wdev to get the vif for + * + * This can be used by mac80211 drivers with direct cfg80211 APIs + * (like the vendor commands) that get a wdev. + * + * Note that this function may return %NULL if the given wdev isn't + * associated with a vif that the driver knows about (e.g. monitor + * or AP_VLAN interfaces.) + */ +struct ieee80211_vif *wdev_to_ieee80211_vif(struct wireless_dev *wdev); + +/** * enum ieee80211_key_flags - key flags * * These flags are used for communication about keys between the driver @@ -1176,14 +1241,18 @@ static inline bool ieee80211_vif_is_mesh(struct ieee80211_vif *vif) * fall back to software crypto. Note that this flag deals only with * RX, if your crypto engine can't deal with TX you can also set the * %IEEE80211_KEY_FLAG_SW_MGMT_TX flag to encrypt such frames in SW. + * @IEEE80211_KEY_FLAG_GENERATE_IV_MGMT: This flag should be set by the + * driver for a CCMP key to indicate that is requires IV generation + * only for managment frames (MFP). */ enum ieee80211_key_flags { - IEEE80211_KEY_FLAG_GENERATE_IV = 1<<1, - IEEE80211_KEY_FLAG_GENERATE_MMIC= 1<<2, - IEEE80211_KEY_FLAG_PAIRWISE = 1<<3, - IEEE80211_KEY_FLAG_SW_MGMT_TX = 1<<4, - IEEE80211_KEY_FLAG_PUT_IV_SPACE = 1<<5, - IEEE80211_KEY_FLAG_RX_MGMT = 1<<6, + IEEE80211_KEY_FLAG_GENERATE_IV_MGMT = BIT(0), + IEEE80211_KEY_FLAG_GENERATE_IV = BIT(1), + IEEE80211_KEY_FLAG_GENERATE_MMIC = BIT(2), + IEEE80211_KEY_FLAG_PAIRWISE = BIT(3), + IEEE80211_KEY_FLAG_SW_MGMT_TX = BIT(4), + IEEE80211_KEY_FLAG_PUT_IV_SPACE = BIT(5), + IEEE80211_KEY_FLAG_RX_MGMT = BIT(6), }; /** @@ -1219,6 +1288,36 @@ struct ieee80211_key_conf { }; /** + * struct ieee80211_cipher_scheme - cipher scheme + * + * This structure contains a cipher scheme information defining + * the secure packet crypto handling. + * + * @cipher: a cipher suite selector + * @iftype: a cipher iftype bit mask indicating an allowed cipher usage + * @hdr_len: a length of a security header used the cipher + * @pn_len: a length of a packet number in the security header + * @pn_off: an offset of pn from the beginning of the security header + * @key_idx_off: an offset of key index byte in the security header + * @key_idx_mask: a bit mask of key_idx bits + * @key_idx_shift: a bit shift needed to get key_idx + * key_idx value calculation: + * (sec_header_base[key_idx_off] & key_idx_mask) >> key_idx_shift + * @mic_len: a mic length in bytes + */ +struct ieee80211_cipher_scheme { + u32 cipher; + u16 iftype; + u8 hdr_len; + u8 pn_len; + u8 pn_off; + u8 key_idx_off; + u8 key_idx_mask; + u8 key_idx_shift; + u8 mic_len; +}; + +/** * enum set_key_cmd - key command * * Used with the set_key() callback in &struct ieee80211_ops, this @@ -1314,6 +1413,7 @@ struct ieee80211_sta_rates { * the station moves to associated state. * @smps_mode: current SMPS mode (off, static or dynamic) * @rates: rate control selection table + * @tdls: indicates whether the STA is a TDLS peer */ struct ieee80211_sta { u32 supp_rates[IEEE80211_NUM_BANDS]; @@ -1328,6 +1428,7 @@ struct ieee80211_sta { enum ieee80211_sta_rx_bandwidth bandwidth; enum ieee80211_smps_mode smps_mode; struct ieee80211_sta_rates __rcu *rates; + bool tdls; /* must be last */ u8 drv_priv[0] __aligned(sizeof(void *)); @@ -1449,8 +1550,6 @@ struct ieee80211_tx_control { * @IEEE80211_HW_CONNECTION_MONITOR: * The hardware performs its own connection monitoring, including * periodic keep-alives to the AP and probing the AP on beacon loss. - * When this flag is set, signaling beacon-loss will cause an immediate - * change to disassociated state. * * @IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC: * This device needs to get data from beacon before association (i.e. @@ -1492,6 +1591,21 @@ struct ieee80211_tx_control { * * @IEEE80211_HW_TIMING_BEACON_ONLY: Use sync timing from beacon frames * only, to allow getting TBTT of a DTIM beacon. + * + * @IEEE80211_HW_SUPPORTS_HT_CCK_RATES: Hardware supports mixing HT/CCK rates + * and can cope with CCK rates in an aggregation session (e.g. by not + * using aggregation for such frames.) + * + * @IEEE80211_HW_CHANCTX_STA_CSA: Support 802.11h based channel-switch (CSA) + * for a single active channel while using channel contexts. When support + * is not enabled the default action is to disconnect when getting the + * CSA frame. + * + * @IEEE80211_HW_CHANGE_RUNNING_CHANCTX: The hardware can change a + * channel context on-the-fly. This is needed for channel switch + * on single-channel hardware. It can also be used as an + * optimization in certain channel switch cases with + * multi-channel. */ enum ieee80211_hw_flags { IEEE80211_HW_HAS_RATE_CONTROL = 1<<0, @@ -1522,6 +1636,8 @@ enum ieee80211_hw_flags { IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF = 1<<25, IEEE80211_HW_TIMING_BEACON_ONLY = 1<<26, IEEE80211_HW_SUPPORTS_HT_CCK_RATES = 1<<27, + IEEE80211_HW_CHANCTX_STA_CSA = 1<<28, + IEEE80211_HW_CHANGE_RUNNING_CHANCTX = 1<<29, }; /** @@ -1546,7 +1662,8 @@ enum ieee80211_hw_flags { * @extra_tx_headroom: headroom to reserve in each transmit skb * for use by the driver (e.g. for transmit headers.) * - * @channel_change_time: time (in microseconds) it takes to change channels. + * @extra_beacon_tailroom: tailroom to reserve in each beacon tx skb. + * Can be used by drivers to add extra IEs. * * @max_signal: Maximum value for signal (rssi) in RX information, used * only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB @@ -1575,10 +1692,6 @@ enum ieee80211_hw_flags { * the hw can report back. * @max_rate_tries: maximum number of tries for each stage * - * @napi_weight: weight used for NAPI polling. You must specify an - * appropriate value here if a napi_poll operation is provided - * by your driver. - * * @max_rx_aggregation_subframes: maximum buffer size (number of * sub-frames) to be used for A-MPDU block ack receiver * aggregation. @@ -1616,6 +1729,10 @@ enum ieee80211_hw_flags { * @uapsd_max_sp_len: maximum number of total buffered frames the WMM AP may * deliver to a WMM STA during any Service Period triggered by the WMM STA. * Use IEEE80211_WMM_IE_STA_QOSINFO_SP_* for correct values. + * + * @n_cipher_schemes: a size of an array of cipher schemes definitions. + * @cipher_schemes: a pointer to an array of cipher scheme definitions + * supported by HW. */ struct ieee80211_hw { struct ieee80211_conf conf; @@ -1624,11 +1741,10 @@ struct ieee80211_hw { void *priv; u32 flags; unsigned int extra_tx_headroom; - int channel_change_time; + unsigned int extra_beacon_tailroom; int vif_data_size; int sta_data_size; int chanctx_data_size; - int napi_weight; u16 queues; u16 max_listen_interval; s8 max_signal; @@ -1643,6 +1759,8 @@ struct ieee80211_hw { netdev_features_t netdev_features; u8 uapsd_queues; u8 uapsd_max_sp_len; + u8 n_cipher_schemes; + const struct ieee80211_cipher_scheme *cipher_schemes; }; /** @@ -1821,7 +1939,7 @@ void ieee80211_free_txskb(struct ieee80211_hw *hw, struct sk_buff *skb); * * Driver informs U-APSD client support by enabling * %IEEE80211_HW_SUPPORTS_UAPSD flag. The mode is configured through the - * uapsd paramater in conf_tx() operation. Hardware needs to send the QoS + * uapsd parameter in conf_tx() operation. Hardware needs to send the QoS * Nullfunc frames and stay awake until the service period has ended. To * utilize U-APSD, dynamic powersave is disabled for voip AC and all frames * from that AC are transmitted with powersave enabled. @@ -2027,7 +2145,7 @@ void ieee80211_free_txskb(struct ieee80211_hw *hw, struct sk_buff *skb); * with the number of frames to be released and which TIDs they are * to come from. In this case, the driver is responsible for setting * the EOSP (for uAPSD) and MORE_DATA bits in the released frames, - * to help the @more_data paramter is passed to tell the driver if + * to help the @more_data parameter is passed to tell the driver if * there is more data on other TIDs -- the TIDs to release frames * from are ignored since mac80211 doesn't know how many frames the * buffers for those TIDs contain. @@ -2045,6 +2163,11 @@ void ieee80211_free_txskb(struct ieee80211_hw *hw, struct sk_buff *skb); * appropriately (only the last frame may have %IEEE80211_TX_STATUS_EOSP) * and also take care of the EOSP and MORE_DATA bits in the frame. * The driver may also use ieee80211_sta_eosp() in this case. + * + * Note that if the driver ever buffers frames other than QoS-data + * frames, it must take care to never send a non-QoS-data frame as + * the last frame in a service period, adding a QoS-nulldata frame + * after a non-QoS-data frame if needed. */ /** @@ -2338,9 +2461,6 @@ enum ieee80211_roc_type { * See the section "Frame filtering" for more information. * This callback must be implemented and can sleep. * - * @set_multicast_list: Configure the device's interface specific RX multicast - * filter. This callback is optional. This callback must be atomic. - * * @set_tim: Set TIM bit. mac80211 calls this function when a TIM bit * must be set or cleared for a given STA. Must be atomic. * @@ -2394,6 +2514,7 @@ enum ieee80211_roc_type { * This process will continue until sched_scan_stop is called. * * @sched_scan_stop: Tell the hardware to stop an ongoing scheduled scan. + * In this case, ieee80211_sched_scan_stopped() must not be called. * * @sw_scan_start: Notifier function that is called just before a software scan * is started. Can be NULL, if the driver doesn't need this notification. @@ -2425,7 +2546,11 @@ enum ieee80211_roc_type { * AP, IBSS/WDS/mesh peer etc. This callback can sleep. * * @sta_remove: Notifies low level driver about removal of an associated - * station, AP, IBSS/WDS/mesh peer etc. This callback can sleep. + * station, AP, IBSS/WDS/mesh peer etc. Note that after the callback + * returns it isn't safe to use the pointer, not even RCU protected; + * no RCU grace period is guaranteed between returning here and freeing + * the station. See @sta_pre_rcu_remove if needed. + * This callback can sleep. * * @sta_add_debugfs: Drivers can use this callback to add debugfs files * when a station is added to mac80211's station list. This callback @@ -2444,7 +2569,17 @@ enum ieee80211_roc_type { * station (which can be the AP, a client, IBSS/WDS/mesh peer etc.) * This callback is mutually exclusive with @sta_add/@sta_remove. * It must not fail for down transitions but may fail for transitions - * up the list of states. + * up the list of states. Also note that after the callback returns it + * isn't safe to use the pointer, not even RCU protected - no RCU grace + * period is guaranteed between returning here and freeing the station. + * See @sta_pre_rcu_remove if needed. + * The callback can sleep. + * + * @sta_pre_rcu_remove: Notify driver about station removal before RCU + * synchronisation. This is useful if a driver needs to have station + * pointers protected using RCU, it can then use this call to clear + * the pointers instead of waiting for an RCU grace period to elapse + * in @sta_state. * The callback can sleep. * * @sta_rc_update: Notifies the driver of changes to the bitrates that can be @@ -2526,6 +2661,7 @@ enum ieee80211_roc_type { * of queues to flush, which is useful if different virtual interfaces * use different hardware queues; it may also indicate all queues. * If the parameter @drop is set to %true, pending frames may be dropped. + * Note that vif can be NULL. * The callback can sleep. * * @channel_switch: Drivers that need (or want) to offload the channel @@ -2533,8 +2669,6 @@ enum ieee80211_roc_type { * callback. They must then call ieee80211_chswitch_done() to indicate * completion of the channel switch. * - * @napi_poll: Poll Rx queue for incoming data frames. - * * @set_antenna: Set antenna configuration (tx_ant, rx_ant) on the device. * Parameters are bitmaps of allowed antennas to use for TX/RX. Drivers may * reject TX/RX mask combinations they cannot support by returning -EINVAL @@ -2572,7 +2706,7 @@ enum ieee80211_roc_type { * parameters. In the case where the driver buffers some frames for * sleeping stations mac80211 will use this callback to tell the driver * to release some frames, either for PS-poll or uAPSD. - * Note that if the @more_data paramter is %false the driver must check + * Note that if the @more_data parameter is %false the driver must check * if there are more frames on the given TIDs, and if there are more than * the frames being released then it must still set the more-data bit in * the frame. If the @more_data parameter is %true, then of course the @@ -2639,6 +2773,11 @@ enum ieee80211_roc_type { * to vif. Possible use is for hw queue remapping. * @unassign_vif_chanctx: Notifies device driver about channel context being * unbound from vif. + * @switch_vif_chanctx: switch a number of vifs from one chanctx to + * another, as specified in the list of + * @ieee80211_vif_chanctx_switch passed to the driver, according + * to the mode defined in &ieee80211_chanctx_switch_mode. + * * @start_ap: Start operation on the AP interface, this is called after all the * information in bss_conf is set and beacon can be retrieved. A channel * context is bound before this is called. Note that if the driver uses @@ -2660,12 +2799,22 @@ enum ieee80211_roc_type { * @channel_switch_beacon: Starts a channel switch to a new channel. * Beacons are modified to include CSA or ECSA IEs before calling this * function. The corresponding count fields in these IEs must be - * decremented, and when they reach zero the driver must call + * decremented, and when they reach 1 the driver must call * ieee80211_csa_finish(). Drivers which use ieee80211_beacon_get() * get the csa counter decremented by mac80211, but must check if it is - * zero using ieee80211_csa_is_complete() after the beacon has been + * 1 using ieee80211_csa_is_complete() after the beacon has been * transmitted and then call ieee80211_csa_finish(). + * If the CSA count starts as zero or 1, this function will not be called, + * since there won't be any time to beacon before the switch anyway. * + * @join_ibss: Join an IBSS (on an IBSS interface); this is called after all + * information in bss_conf is set up and the beacon can be retrieved. A + * channel context is bound before this is called. + * @leave_ibss: Leave the IBSS again. + * + * @get_expected_throughput: extract the expected throughput towards the + * specified station. The returned value is expressed in Kbps. It returns 0 + * if the RC algorithm does not have proper data to provide. */ struct ieee80211_ops { void (*tx)(struct ieee80211_hw *hw, @@ -2700,10 +2849,6 @@ struct ieee80211_ops { unsigned int changed_flags, unsigned int *total_flags, u64 multicast); - void (*set_multicast_list)(struct ieee80211_hw *hw, - struct ieee80211_vif *vif, bool allmulti, - struct netdev_hw_addr_list *mc_list); - int (*set_tim)(struct ieee80211_hw *hw, struct ieee80211_sta *sta, bool set); int (*set_key)(struct ieee80211_hw *hw, enum set_key_cmd cmd, @@ -2727,7 +2872,7 @@ struct ieee80211_ops { struct ieee80211_vif *vif, struct cfg80211_sched_scan_request *req, struct ieee80211_sched_scan_ies *ies); - void (*sched_scan_stop)(struct ieee80211_hw *hw, + int (*sched_scan_stop)(struct ieee80211_hw *hw, struct ieee80211_vif *vif); void (*sw_scan_start)(struct ieee80211_hw *hw); void (*sw_scan_complete)(struct ieee80211_hw *hw); @@ -2757,6 +2902,9 @@ struct ieee80211_ops { struct ieee80211_sta *sta, enum ieee80211_sta_state old_state, enum ieee80211_sta_state new_state); + void (*sta_pre_rcu_remove)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct ieee80211_sta *sta); void (*sta_rc_update)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, struct ieee80211_sta *sta, @@ -2785,10 +2933,10 @@ struct ieee80211_ops { struct netlink_callback *cb, void *data, int len); #endif - void (*flush)(struct ieee80211_hw *hw, u32 queues, bool drop); + void (*flush)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, + u32 queues, bool drop); void (*channel_switch)(struct ieee80211_hw *hw, struct ieee80211_channel_switch *ch_switch); - int (*napi_poll)(struct ieee80211_hw *hw, int budget); int (*set_antenna)(struct ieee80211_hw *hw, u32 tx_ant, u32 rx_ant); int (*get_antenna)(struct ieee80211_hw *hw, u32 *tx_ant, u32 *rx_ant); @@ -2846,6 +2994,10 @@ struct ieee80211_ops { void (*unassign_vif_chanctx)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, struct ieee80211_chanctx_conf *ctx); + int (*switch_vif_chanctx)(struct ieee80211_hw *hw, + struct ieee80211_vif_chanctx_switch *vifs, + int n_vifs, + enum ieee80211_chanctx_switch_mode mode); void (*restart_complete)(struct ieee80211_hw *hw); @@ -2857,6 +3009,10 @@ struct ieee80211_ops { void (*channel_switch_beacon)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, struct cfg80211_chan_def *chandef); + + int (*join_ibss)(struct ieee80211_hw *hw, struct ieee80211_vif *vif); + void (*leave_ibss)(struct ieee80211_hw *hw, struct ieee80211_vif *vif); + u32 (*get_expected_throughput)(struct ieee80211_sta *sta); }; /** @@ -3067,21 +3223,21 @@ void ieee80211_free_hw(struct ieee80211_hw *hw); */ void ieee80211_restart_hw(struct ieee80211_hw *hw); -/** ieee80211_napi_schedule - schedule NAPI poll - * - * Use this function to schedule NAPI polling on a device. - * - * @hw: the hardware to start polling - */ -void ieee80211_napi_schedule(struct ieee80211_hw *hw); - -/** ieee80211_napi_complete - complete NAPI polling - * - * Use this function to finish NAPI polling on a device. +/** + * ieee80211_napi_add - initialize mac80211 NAPI context + * @hw: the hardware to initialize the NAPI context on + * @napi: the NAPI context to initialize + * @napi_dev: dummy NAPI netdevice, here to not waste the space if the + * driver doesn't use NAPI + * @poll: poll function + * @weight: default weight * - * @hw: the hardware to stop polling + * See also netif_napi_add(). */ -void ieee80211_napi_complete(struct ieee80211_hw *hw); +void ieee80211_napi_add(struct ieee80211_hw *hw, struct napi_struct *napi, + struct net_device *napi_dev, + int (*poll)(struct napi_struct *, int), + int weight); /** * ieee80211_rx - receive frame @@ -3306,6 +3462,47 @@ void ieee80211_tx_status_irqsafe(struct ieee80211_hw *hw, */ void ieee80211_report_low_ack(struct ieee80211_sta *sta, u32 num_packets); +#define IEEE80211_MAX_CSA_COUNTERS_NUM 2 + +/** + * struct ieee80211_mutable_offsets - mutable beacon offsets + * @tim_offset: position of TIM element + * @tim_length: size of TIM element + * @csa_counter_offs: array of IEEE80211_MAX_CSA_COUNTERS_NUM offsets + * to CSA counters. This array can contain zero values which + * should be ignored. + */ +struct ieee80211_mutable_offsets { + u16 tim_offset; + u16 tim_length; + + u16 csa_counter_offs[IEEE80211_MAX_CSA_COUNTERS_NUM]; +}; + +/** + * ieee80211_beacon_get_template - beacon template generation function + * @hw: pointer obtained from ieee80211_alloc_hw(). + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * @offs: &struct ieee80211_mutable_offsets pointer to struct that will + * receive the offsets that may be updated by the driver. + * + * If the driver implements beaconing modes, it must use this function to + * obtain the beacon template. + * + * This function should be used if the beacon frames are generated by the + * device, and then the driver must use the returned beacon as the template + * The driver or the device are responsible to update the DTIM and, when + * applicable, the CSA count. + * + * The driver is responsible for freeing the returned skb. + * + * Return: The beacon template. %NULL on error. + */ +struct sk_buff * +ieee80211_beacon_get_template(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct ieee80211_mutable_offsets *offs); + /** * ieee80211_beacon_get_tim - beacon generation function * @hw: pointer obtained from ieee80211_alloc_hw(). @@ -3317,16 +3514,12 @@ void ieee80211_report_low_ack(struct ieee80211_sta *sta, u32 num_packets); * Set to 0 if invalid (in non-AP modes). * * If the driver implements beaconing modes, it must use this function to - * obtain the beacon frame/template. + * obtain the beacon frame. * * If the beacon frames are generated by the host system (i.e., not in * hardware/firmware), the driver uses this function to get each beacon - * frame from mac80211 -- it is responsible for calling this function - * before the beacon is needed (e.g. based on hardware interrupt). - * - * If the beacon frames are generated by the device, then the driver - * must use the returned beacon as the template and change the TIM IE - * according to the current DTIM parameters/TIM bitmap. + * frame from mac80211 -- it is responsible for calling this function exactly + * once before the beacon is needed (e.g. based on hardware interrupt). * * The driver is responsible for freeing the returned skb. * @@ -3352,17 +3545,31 @@ static inline struct sk_buff *ieee80211_beacon_get(struct ieee80211_hw *hw, } /** + * ieee80211_csa_update_counter - request mac80211 to decrement the csa counter + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * + * The csa counter should be updated after each beacon transmission. + * This function is called implicitly when + * ieee80211_beacon_get/ieee80211_beacon_get_tim are called, however if the + * beacon frames are generated by the device, the driver should call this + * function after each beacon transmission to sync mac80211's csa counters. + * + * Return: new csa counter value + */ +u8 ieee80211_csa_update_counter(struct ieee80211_vif *vif); + +/** * ieee80211_csa_finish - notify mac80211 about channel switch * @vif: &struct ieee80211_vif pointer from the add_interface callback. * * After a channel switch announcement was scheduled and the counter in this - * announcement hit zero, this function must be called by the driver to + * announcement hits 1, this function must be called by the driver to * notify mac80211 that the channel can be changed. */ void ieee80211_csa_finish(struct ieee80211_vif *vif); /** - * ieee80211_csa_is_complete - find out if counters reached zero + * ieee80211_csa_is_complete - find out if counters reached 1 * @vif: &struct ieee80211_vif pointer from the add_interface callback. * * This function returns whether the channel switch counters reached zero. @@ -3920,6 +4127,25 @@ void ieee80211_iterate_active_interfaces_atomic(struct ieee80211_hw *hw, void *data); /** + * ieee80211_iterate_active_interfaces_rtnl - iterate active interfaces + * + * This function iterates over the interfaces associated with a given + * hardware that are currently active and calls the callback for them. + * This version can only be used while holding the RTNL. + * + * @hw: the hardware struct of which the interfaces should be iterated over + * @iter_flags: iteration flags, see &enum ieee80211_interface_iteration_flags + * @iterator: the iterator function to call, cannot sleep + * @data: first argument of the iterator function + */ +void ieee80211_iterate_active_interfaces_rtnl(struct ieee80211_hw *hw, + u32 iter_flags, + void (*iterator)(void *data, + u8 *mac, + struct ieee80211_vif *vif), + void *data); + +/** * ieee80211_queue_work - add work onto the mac80211 workqueue * * Drivers and mac80211 use this to add work onto the mac80211 workqueue. @@ -4336,7 +4562,6 @@ struct ieee80211_tx_rate_control { }; struct rate_control_ops { - struct module *module; const char *name; void *(*alloc)(struct ieee80211_hw *hw, struct dentry *debugfsdir); void (*free)(void *priv); @@ -4361,6 +4586,8 @@ struct rate_control_ops { void (*add_sta_debugfs)(void *priv, void *priv_sta, struct dentry *dir); void (*remove_sta_debugfs)(void *priv, void *priv_sta); + + u32 (*get_expected_throughput)(void *priv_sta); }; static inline int rate_supported(struct ieee80211_sta *sta, @@ -4438,8 +4665,8 @@ int rate_control_set_rates(struct ieee80211_hw *hw, struct ieee80211_sta *pubsta, struct ieee80211_sta_rates *rates); -int ieee80211_rate_control_register(struct rate_control_ops *ops); -void ieee80211_rate_control_unregister(struct rate_control_ops *ops); +int ieee80211_rate_control_register(const struct rate_control_ops *ops); +void ieee80211_rate_control_unregister(const struct rate_control_ops *ops); static inline bool conf_is_ht20(struct ieee80211_conf *conf) @@ -4470,7 +4697,9 @@ conf_is_ht40(struct ieee80211_conf *conf) static inline bool conf_is_ht(struct ieee80211_conf *conf) { - return conf->chandef.width != NL80211_CHAN_WIDTH_20_NOHT; + return (conf->chandef.width != NL80211_CHAN_WIDTH_5) && + (conf->chandef.width != NL80211_CHAN_WIDTH_10) && + (conf->chandef.width != NL80211_CHAN_WIDTH_20_NOHT); } static inline enum nl80211_iftype @@ -4525,4 +4754,65 @@ void ieee80211_report_wowlan_wakeup(struct ieee80211_vif *vif, struct cfg80211_wowlan_wakeup *wakeup, gfp_t gfp); +/** + * ieee80211_tx_prepare_skb - prepare an 802.11 skb for transmission + * @hw: pointer as obtained from ieee80211_alloc_hw() + * @vif: virtual interface + * @skb: frame to be sent from within the driver + * @band: the band to transmit on + * @sta: optional pointer to get the station to send the frame to + * + * Note: must be called under RCU lock + */ +bool ieee80211_tx_prepare_skb(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, struct sk_buff *skb, + int band, struct ieee80211_sta **sta); + +/** + * struct ieee80211_noa_data - holds temporary data for tracking P2P NoA state + * + * @next_tsf: TSF timestamp of the next absent state change + * @has_next_tsf: next absent state change event pending + * + * @absent: descriptor bitmask, set if GO is currently absent + * + * private: + * + * @count: count fields from the NoA descriptors + * @desc: adjusted data from the NoA + */ +struct ieee80211_noa_data { + u32 next_tsf; + bool has_next_tsf; + + u8 absent; + + u8 count[IEEE80211_P2P_NOA_DESC_MAX]; + struct { + u32 start; + u32 duration; + u32 interval; + } desc[IEEE80211_P2P_NOA_DESC_MAX]; +}; + +/** + * ieee80211_parse_p2p_noa - initialize NoA tracking data from P2P IE + * + * @attr: P2P NoA IE + * @data: NoA tracking data + * @tsf: current TSF timestamp + * + * Return: number of successfully parsed descriptors + */ +int ieee80211_parse_p2p_noa(const struct ieee80211_p2p_noa_attr *attr, + struct ieee80211_noa_data *data, u32 tsf); + +/** + * ieee80211_update_p2p_noa - get next pending P2P GO absent state change + * + * @data: NoA tracking data + * @tsf: current TSF timestamp + */ +void ieee80211_update_p2p_noa(struct ieee80211_noa_data *data, u32 tsf); + #endif /* MAC80211_H */ |