diff options
Diffstat (limited to 'include/media')
51 files changed, 1729 insertions, 1013 deletions
diff --git a/include/media/adv7343.h b/include/media/adv7343.h index 944757be49b..e4142b1ef8c 100644 --- a/include/media/adv7343.h +++ b/include/media/adv7343.h @@ -28,12 +28,7 @@ * @pll_control: PLL and oversampling control. This control allows internal * PLL 1 circuit to be powered down and the oversampling to be * switched off. - * @dac_1: power on/off DAC 1. - * @dac_2: power on/off DAC 2. - * @dac_3: power on/off DAC 3. - * @dac_4: power on/off DAC 4. - * @dac_5: power on/off DAC 5. - * @dac_6: power on/off DAC 6. + * @dac: array to configure power on/off DAC's 1..6 * * Power mode register (Register 0x0), for more info refer REGISTER MAP ACCESS * section of datasheet[1], table 17 page no 30. @@ -43,23 +38,16 @@ struct adv7343_power_mode { bool sleep_mode; bool pll_control; - bool dac_1; - bool dac_2; - bool dac_3; - bool dac_4; - bool dac_5; - bool dac_6; + u32 dac[6]; }; /** * struct adv7343_sd_config - SD Only Output Configuration. - * @sd_dac_out1: Configure SD DAC Output 1. - * @sd_dac_out2: Configure SD DAC Output 2. + * @sd_dac_out: array configuring SD DAC Outputs 1 and 2 */ struct adv7343_sd_config { /* SD only Output Configuration */ - bool sd_dac_out1; - bool sd_dac_out2; + u32 sd_dac_out[2]; }; /** diff --git a/include/media/adv7511.h b/include/media/adv7511.h new file mode 100644 index 00000000000..bb78bed9a5b --- /dev/null +++ b/include/media/adv7511.h @@ -0,0 +1,48 @@ +/* + * Analog Devices ADV7511 HDMI Transmitter Device Driver + * + * Copyright 2013 Cisco Systems, Inc. and/or its affiliates. All rights reserved. + * + * This program is free software; you may redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; version 2 of the License. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF + * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS + * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN + * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN + * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE + * SOFTWARE. + */ + +#ifndef ADV7511_H +#define ADV7511_H + +/* notify events */ +#define ADV7511_MONITOR_DETECT 0 +#define ADV7511_EDID_DETECT 1 + + +struct adv7511_monitor_detect { + int present; +}; + +struct adv7511_edid_detect { + int present; + int segment; +}; + +struct adv7511_cec_arg { + void *arg; + u32 f_flags; +}; + +struct adv7511_platform_data { + uint8_t i2c_edid; + uint8_t i2c_cec; + uint32_t cec_clk; +}; + +#endif diff --git a/include/media/adv7604.h b/include/media/adv7604.h index dc004bc926c..aa1c4477722 100644 --- a/include/media/adv7604.h +++ b/include/media/adv7604.h @@ -21,6 +21,8 @@ #ifndef _ADV7604_ #define _ADV7604_ +#include <linux/types.h> + /* Analog input muxing modes (AFE register 0x02, [2:0]) */ enum adv7604_ain_sel { ADV7604_AIN1_2_3_NC_SYNC_1_2 = 0, @@ -30,14 +32,18 @@ enum adv7604_ain_sel { ADV7604_AIN9_4_5_6_SYNC_2_1 = 4, }; -/* Bus rotation and reordering (IO register 0x04, [7:5]) */ -enum adv7604_op_ch_sel { - ADV7604_OP_CH_SEL_GBR = 0, - ADV7604_OP_CH_SEL_GRB = 1, - ADV7604_OP_CH_SEL_BGR = 2, - ADV7604_OP_CH_SEL_RGB = 3, - ADV7604_OP_CH_SEL_BRG = 4, - ADV7604_OP_CH_SEL_RBG = 5, +/* + * Bus rotation and reordering. This is used to specify component reordering on + * the board and describes the components order on the bus when the ADV7604 + * outputs RGB. + */ +enum adv7604_bus_order { + ADV7604_BUS_ORDER_RGB, /* No operation */ + ADV7604_BUS_ORDER_GRB, /* Swap 1-2 */ + ADV7604_BUS_ORDER_RBG, /* Swap 2-3 */ + ADV7604_BUS_ORDER_BGR, /* Swap 1-3 */ + ADV7604_BUS_ORDER_BRG, /* Rotate right */ + ADV7604_BUS_ORDER_GBR, /* Rotate left */ }; /* Input Color Space (IO register 0x02, [7:4]) */ @@ -53,62 +59,84 @@ enum adv7604_inp_color_space { ADV7604_INP_COLOR_SPACE_AUTO = 0xf, }; -/* Select output format (IO register 0x03, [7:0]) */ -enum adv7604_op_format_sel { - ADV7604_OP_FORMAT_SEL_SDR_ITU656_8 = 0x00, - ADV7604_OP_FORMAT_SEL_SDR_ITU656_10 = 0x01, - ADV7604_OP_FORMAT_SEL_SDR_ITU656_12_MODE0 = 0x02, - ADV7604_OP_FORMAT_SEL_SDR_ITU656_12_MODE1 = 0x06, - ADV7604_OP_FORMAT_SEL_SDR_ITU656_12_MODE2 = 0x0a, - ADV7604_OP_FORMAT_SEL_DDR_422_8 = 0x20, - ADV7604_OP_FORMAT_SEL_DDR_422_10 = 0x21, - ADV7604_OP_FORMAT_SEL_DDR_422_12_MODE0 = 0x22, - ADV7604_OP_FORMAT_SEL_DDR_422_12_MODE1 = 0x23, - ADV7604_OP_FORMAT_SEL_DDR_422_12_MODE2 = 0x24, - ADV7604_OP_FORMAT_SEL_SDR_444_24 = 0x40, - ADV7604_OP_FORMAT_SEL_SDR_444_30 = 0x41, - ADV7604_OP_FORMAT_SEL_SDR_444_36_MODE0 = 0x42, - ADV7604_OP_FORMAT_SEL_DDR_444_24 = 0x60, - ADV7604_OP_FORMAT_SEL_DDR_444_30 = 0x61, - ADV7604_OP_FORMAT_SEL_DDR_444_36 = 0x62, - ADV7604_OP_FORMAT_SEL_SDR_ITU656_16 = 0x80, - ADV7604_OP_FORMAT_SEL_SDR_ITU656_20 = 0x81, - ADV7604_OP_FORMAT_SEL_SDR_ITU656_24_MODE0 = 0x82, - ADV7604_OP_FORMAT_SEL_SDR_ITU656_24_MODE1 = 0x86, - ADV7604_OP_FORMAT_SEL_SDR_ITU656_24_MODE2 = 0x8a, +/* Select output format (IO register 0x03, [4:2]) */ +enum adv7604_op_format_mode_sel { + ADV7604_OP_FORMAT_MODE0 = 0x00, + ADV7604_OP_FORMAT_MODE1 = 0x04, + ADV7604_OP_FORMAT_MODE2 = 0x08, +}; + +enum adv7604_drive_strength { + ADV7604_DR_STR_MEDIUM_LOW = 1, + ADV7604_DR_STR_MEDIUM_HIGH = 2, + ADV7604_DR_STR_HIGH = 3, +}; + +enum adv7604_int1_config { + ADV7604_INT1_CONFIG_OPEN_DRAIN, + ADV7604_INT1_CONFIG_ACTIVE_LOW, + ADV7604_INT1_CONFIG_ACTIVE_HIGH, + ADV7604_INT1_CONFIG_DISABLED, +}; + +enum adv7604_page { + ADV7604_PAGE_IO, + ADV7604_PAGE_AVLINK, + ADV7604_PAGE_CEC, + ADV7604_PAGE_INFOFRAME, + ADV7604_PAGE_ESDP, + ADV7604_PAGE_DPP, + ADV7604_PAGE_AFE, + ADV7604_PAGE_REP, + ADV7604_PAGE_EDID, + ADV7604_PAGE_HDMI, + ADV7604_PAGE_TEST, + ADV7604_PAGE_CP, + ADV7604_PAGE_VDP, + ADV7604_PAGE_MAX, }; /* Platform dependent definition */ struct adv7604_platform_data { - /* connector - HDMI or DVI? */ - unsigned connector_hdmi:1; - /* DIS_PWRDNB: 1 if the PWRDNB pin is unused and unconnected */ unsigned disable_pwrdnb:1; /* DIS_CABLE_DET_RST: 1 if the 5V pins are unused and unconnected */ unsigned disable_cable_det_rst:1; + int default_input; + /* Analog input muxing mode */ enum adv7604_ain_sel ain_sel; /* Bus rotation and reordering */ - enum adv7604_op_ch_sel op_ch_sel; + enum adv7604_bus_order bus_order; + + /* Select output format mode */ + enum adv7604_op_format_mode_sel op_format_mode_sel; - /* Select output format */ - enum adv7604_op_format_sel op_format_sel; + /* Configuration of the INT1 pin */ + enum adv7604_int1_config int1_config; /* IO register 0x02 */ unsigned alt_gamma:1; unsigned op_656_range:1; - unsigned rgb_out:1; unsigned alt_data_sat:1; /* IO register 0x05 */ unsigned blank_data:1; unsigned insert_av_codes:1; unsigned replicate_av_codes:1; - unsigned invert_cbcr:1; + + /* IO register 0x06 */ + unsigned inv_vs_pol:1; + unsigned inv_hs_pol:1; + unsigned inv_llc_pol:1; + + /* IO register 0x14 */ + enum adv7604_drive_strength dr_str_data; + enum adv7604_drive_strength dr_str_clk; + enum adv7604_drive_strength dr_str_sync; /* IO register 0x30 */ unsigned output_bus_lsb_to_msb:1; @@ -117,28 +145,20 @@ struct adv7604_platform_data { unsigned hdmi_free_run_mode; /* i2c addresses: 0 == use default */ - u8 i2c_avlink; - u8 i2c_cec; - u8 i2c_infoframe; - u8 i2c_esdp; - u8 i2c_dpp; - u8 i2c_afe; - u8 i2c_repeater; - u8 i2c_edid; - u8 i2c_hdmi; - u8 i2c_test; - u8 i2c_cp; - u8 i2c_vdp; + u8 i2c_addresses[ADV7604_PAGE_MAX]; }; -/* - * Mode of operation. - * This is used as the input argument of the s_routing video op. - */ -enum adv7604_mode { - ADV7604_MODE_COMP, - ADV7604_MODE_GR, - ADV7604_MODE_HDMI, +enum adv7604_pad { + ADV7604_PAD_HDMI_PORT_A = 0, + ADV7604_PAD_HDMI_PORT_B = 1, + ADV7604_PAD_HDMI_PORT_C = 2, + ADV7604_PAD_HDMI_PORT_D = 3, + ADV7604_PAD_VGA_RGB = 4, + ADV7604_PAD_VGA_COMP = 5, + /* The source pad is either 1 (ADV7611) or 6 (ADV7604) */ + ADV7604_PAD_SOURCE = 6, + ADV7611_PAD_SOURCE = 1, + ADV7604_PAD_MAX = 7, }; #define V4L2_CID_ADV_RX_ANALOG_SAMPLING_PHASE (V4L2_CID_DV_CLASS_BASE + 0x1000) diff --git a/include/media/adv7842.h b/include/media/adv7842.h new file mode 100644 index 00000000000..924cbb8d004 --- /dev/null +++ b/include/media/adv7842.h @@ -0,0 +1,260 @@ +/* + * adv7842 - Analog Devices ADV7842 video decoder driver + * + * Copyright 2013 Cisco Systems, Inc. and/or its affiliates. All rights reserved. + * + * This program is free software; you may redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; version 2 of the License. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF + * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS + * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN + * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN + * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE + * SOFTWARE. + * + */ + +#ifndef _ADV7842_ +#define _ADV7842_ + +/* Analog input muxing modes (AFE register 0x02, [2:0]) */ +enum adv7842_ain_sel { + ADV7842_AIN1_2_3_NC_SYNC_1_2 = 0, + ADV7842_AIN4_5_6_NC_SYNC_2_1 = 1, + ADV7842_AIN7_8_9_NC_SYNC_3_1 = 2, + ADV7842_AIN10_11_12_NC_SYNC_4_1 = 3, + ADV7842_AIN9_4_5_6_SYNC_2_1 = 4, +}; + +/* Bus rotation and reordering (IO register 0x04, [7:5]) */ +enum adv7842_op_ch_sel { + ADV7842_OP_CH_SEL_GBR = 0, + ADV7842_OP_CH_SEL_GRB = 1, + ADV7842_OP_CH_SEL_BGR = 2, + ADV7842_OP_CH_SEL_RGB = 3, + ADV7842_OP_CH_SEL_BRG = 4, + ADV7842_OP_CH_SEL_RBG = 5, +}; + +/* Mode of operation */ +enum adv7842_mode { + ADV7842_MODE_SDP, + ADV7842_MODE_COMP, + ADV7842_MODE_RGB, + ADV7842_MODE_HDMI +}; + +/* Video standard select (IO register 0x00, [5:0]) */ +enum adv7842_vid_std_select { + /* SDP */ + ADV7842_SDP_VID_STD_CVBS_SD_4x1 = 0x01, + ADV7842_SDP_VID_STD_YC_SD4_x1 = 0x09, + /* RGB */ + ADV7842_RGB_VID_STD_AUTO_GRAPH_MODE = 0x07, + /* HDMI GR */ + ADV7842_HDMI_GR_VID_STD_AUTO_GRAPH_MODE = 0x02, + /* HDMI COMP */ + ADV7842_HDMI_COMP_VID_STD_HD_1250P = 0x1e, +}; + +/* Input Color Space (IO register 0x02, [7:4]) */ +enum adv7842_inp_color_space { + ADV7842_INP_COLOR_SPACE_LIM_RGB = 0, + ADV7842_INP_COLOR_SPACE_FULL_RGB = 1, + ADV7842_INP_COLOR_SPACE_LIM_YCbCr_601 = 2, + ADV7842_INP_COLOR_SPACE_LIM_YCbCr_709 = 3, + ADV7842_INP_COLOR_SPACE_XVYCC_601 = 4, + ADV7842_INP_COLOR_SPACE_XVYCC_709 = 5, + ADV7842_INP_COLOR_SPACE_FULL_YCbCr_601 = 6, + ADV7842_INP_COLOR_SPACE_FULL_YCbCr_709 = 7, + ADV7842_INP_COLOR_SPACE_AUTO = 0xf, +}; + +/* Select output format (IO register 0x03, [7:0]) */ +enum adv7842_op_format_sel { + ADV7842_OP_FORMAT_SEL_SDR_ITU656_8 = 0x00, + ADV7842_OP_FORMAT_SEL_SDR_ITU656_10 = 0x01, + ADV7842_OP_FORMAT_SEL_SDR_ITU656_12_MODE0 = 0x02, + ADV7842_OP_FORMAT_SEL_SDR_ITU656_12_MODE1 = 0x06, + ADV7842_OP_FORMAT_SEL_SDR_ITU656_12_MODE2 = 0x0a, + ADV7842_OP_FORMAT_SEL_DDR_422_8 = 0x20, + ADV7842_OP_FORMAT_SEL_DDR_422_10 = 0x21, + ADV7842_OP_FORMAT_SEL_DDR_422_12_MODE0 = 0x22, + ADV7842_OP_FORMAT_SEL_DDR_422_12_MODE1 = 0x23, + ADV7842_OP_FORMAT_SEL_DDR_422_12_MODE2 = 0x24, + ADV7842_OP_FORMAT_SEL_SDR_444_24 = 0x40, + ADV7842_OP_FORMAT_SEL_SDR_444_30 = 0x41, + ADV7842_OP_FORMAT_SEL_SDR_444_36_MODE0 = 0x42, + ADV7842_OP_FORMAT_SEL_DDR_444_24 = 0x60, + ADV7842_OP_FORMAT_SEL_DDR_444_30 = 0x61, + ADV7842_OP_FORMAT_SEL_DDR_444_36 = 0x62, + ADV7842_OP_FORMAT_SEL_SDR_ITU656_16 = 0x80, + ADV7842_OP_FORMAT_SEL_SDR_ITU656_20 = 0x81, + ADV7842_OP_FORMAT_SEL_SDR_ITU656_24_MODE0 = 0x82, + ADV7842_OP_FORMAT_SEL_SDR_ITU656_24_MODE1 = 0x86, + ADV7842_OP_FORMAT_SEL_SDR_ITU656_24_MODE2 = 0x8a, +}; + +enum adv7842_select_input { + ADV7842_SELECT_HDMI_PORT_A, + ADV7842_SELECT_HDMI_PORT_B, + ADV7842_SELECT_VGA_RGB, + ADV7842_SELECT_VGA_COMP, + ADV7842_SELECT_SDP_CVBS, + ADV7842_SELECT_SDP_YC, +}; + +enum adv7842_drive_strength { + ADV7842_DR_STR_LOW = 0, + ADV7842_DR_STR_MEDIUM_LOW = 1, + ADV7842_DR_STR_MEDIUM_HIGH = 2, + ADV7842_DR_STR_HIGH = 3, +}; + +struct adv7842_sdp_csc_coeff { + bool manual; + uint16_t scaling; + uint16_t A1; + uint16_t A2; + uint16_t A3; + uint16_t A4; + uint16_t B1; + uint16_t B2; + uint16_t B3; + uint16_t B4; + uint16_t C1; + uint16_t C2; + uint16_t C3; + uint16_t C4; +}; + +struct adv7842_sdp_io_sync_adjustment { + bool adjust; + uint16_t hs_beg; + uint16_t hs_width; + uint16_t de_beg; + uint16_t de_end; + uint8_t vs_beg_o; + uint8_t vs_beg_e; + uint8_t vs_end_o; + uint8_t vs_end_e; + uint8_t de_v_beg_o; + uint8_t de_v_beg_e; + uint8_t de_v_end_o; + uint8_t de_v_end_e; +}; + +/* Platform dependent definition */ +struct adv7842_platform_data { + /* chip reset during probe */ + unsigned chip_reset:1; + + /* DIS_PWRDNB: 1 if the PWRDNB pin is unused and unconnected */ + unsigned disable_pwrdnb:1; + + /* DIS_CABLE_DET_RST: 1 if the 5V pins are unused and unconnected */ + unsigned disable_cable_det_rst:1; + + /* Analog input muxing mode */ + enum adv7842_ain_sel ain_sel; + + /* Bus rotation and reordering */ + enum adv7842_op_ch_sel op_ch_sel; + + /* Default mode */ + enum adv7842_mode mode; + + /* Default input */ + unsigned input; + + /* Video standard */ + enum adv7842_vid_std_select vid_std_select; + + /* Select output format */ + enum adv7842_op_format_sel op_format_sel; + + /* IO register 0x02 */ + unsigned alt_gamma:1; + unsigned op_656_range:1; + unsigned rgb_out:1; + unsigned alt_data_sat:1; + + /* IO register 0x05 */ + unsigned blank_data:1; + unsigned insert_av_codes:1; + unsigned replicate_av_codes:1; + unsigned invert_cbcr:1; + + /* IO register 0x30 */ + unsigned output_bus_lsb_to_msb:1; + + /* IO register 0x14 */ + enum adv7842_drive_strength dr_str_data; + enum adv7842_drive_strength dr_str_clk; + enum adv7842_drive_strength dr_str_sync; + + /* + * IO register 0x19: Adjustment to the LLC DLL phase in + * increments of 1/32 of a clock period. + */ + unsigned llc_dll_phase:5; + + /* External RAM for 3-D comb or frame synchronizer */ + unsigned sd_ram_size; /* ram size in MB */ + unsigned sd_ram_ddr:1; /* ddr or sdr sdram */ + + /* HDMI free run, CP-reg 0xBA */ + unsigned hdmi_free_run_enable:1; + /* 0 = Mode 0: run when there is no TMDS clock + 1 = Mode 1: run when there is no TMDS clock or the + video resolution does not match programmed one. */ + unsigned hdmi_free_run_mode:1; + + /* SDP free run, CP-reg 0xDD */ + unsigned sdp_free_run_auto:1; + unsigned sdp_free_run_man_col_en:1; + unsigned sdp_free_run_cbar_en:1; + unsigned sdp_free_run_force:1; + + /* HPA manual (0) or auto (1), affects HDMI register 0x69 */ + unsigned hpa_auto:1; + + struct adv7842_sdp_csc_coeff sdp_csc_coeff; + + struct adv7842_sdp_io_sync_adjustment sdp_io_sync_625; + struct adv7842_sdp_io_sync_adjustment sdp_io_sync_525; + + /* i2c addresses */ + u8 i2c_sdp_io; + u8 i2c_sdp; + u8 i2c_cp; + u8 i2c_vdp; + u8 i2c_afe; + u8 i2c_hdmi; + u8 i2c_repeater; + u8 i2c_edid; + u8 i2c_infoframe; + u8 i2c_cec; + u8 i2c_avlink; +}; + +#define V4L2_CID_ADV_RX_ANALOG_SAMPLING_PHASE (V4L2_CID_DV_CLASS_BASE + 0x1000) +#define V4L2_CID_ADV_RX_FREE_RUN_COLOR_MANUAL (V4L2_CID_DV_CLASS_BASE + 0x1001) +#define V4L2_CID_ADV_RX_FREE_RUN_COLOR (V4L2_CID_DV_CLASS_BASE + 0x1002) + +/* notify events */ +#define ADV7842_FMT_CHANGE 1 + +/* custom ioctl, used to test the external RAM that's used by the + * deinterlacer. */ +#define ADV7842_CMD_RAM_TEST _IO('V', BASE_VIDIOC_PRIVATE) + +#define ADV7842_EDID_PORT_A 0 +#define ADV7842_EDID_PORT_B 1 +#define ADV7842_EDID_PORT_VGA 2 + +#endif diff --git a/include/media/atmel-isi.h b/include/media/atmel-isi.h index 65682307570..2b023471ac8 100644 --- a/include/media/atmel-isi.h +++ b/include/media/atmel-isi.h @@ -56,6 +56,7 @@ #define ISI_CFG1_FRATE_DIV_6 (5 << 8) #define ISI_CFG1_FRATE_DIV_7 (6 << 8) #define ISI_CFG1_FRATE_DIV_8 (7 << 8) +#define ISI_CFG1_FRATE_DIV_MASK (7 << 8) #define ISI_CFG1_DISCR (1 << 11) #define ISI_CFG1_FULL_MODE (1 << 12) @@ -66,6 +67,7 @@ #define ISI_CFG2_YCC_SWAP_MODE_1 (1 << 28) #define ISI_CFG2_YCC_SWAP_MODE_2 (2 << 28) #define ISI_CFG2_YCC_SWAP_MODE_3 (3 << 28) +#define ISI_CFG2_YCC_SWAP_MODE_MASK (3 << 28) #define ISI_CFG2_IM_VSIZE_OFFSET 0 #define ISI_CFG2_IM_HSIZE_OFFSET 16 #define ISI_CFG2_IM_VSIZE_MASK (0x7FF << ISI_CFG2_IM_VSIZE_OFFSET) diff --git a/include/media/davinci/vpbe_display.h b/include/media/davinci/vpbe_display.h index 8dffffedbb5..637749a9143 100644 --- a/include/media/davinci/vpbe_display.h +++ b/include/media/davinci/vpbe_display.h @@ -16,6 +16,7 @@ /* Header files */ #include <linux/videodev2.h> #include <media/v4l2-common.h> +#include <media/v4l2-fh.h> #include <media/videobuf2-dma-contig.h> #include <media/davinci/vpbe_types.h> #include <media/davinci/vpbe_osd.h> @@ -94,8 +95,6 @@ struct vpbe_layer { * has selected */ enum v4l2_memory memory; - /* Used to keep track of state of the priority */ - struct v4l2_prio_state prio; /* Used to store pixel format */ struct v4l2_pix_format pix_fmt; enum v4l2_field buf_field; @@ -134,14 +133,13 @@ struct vpbe_display { /* File handle structure */ struct vpbe_fh { + struct v4l2_fh fh; /* vpbe device structure */ struct vpbe_display *disp_dev; /* pointer to layer object for opened device */ struct vpbe_layer *layer; /* Indicates whether this file handle is doing IO */ unsigned char io_allowed; - /* Used to keep track priority of this instance */ - enum v4l2_priority prio; }; struct buf_config_params { diff --git a/include/media/davinci/vpbe_osd.h b/include/media/davinci/vpbe_osd.h index 42628fcfe1b..de59364d7ed 100644 --- a/include/media/davinci/vpbe_osd.h +++ b/include/media/davinci/vpbe_osd.h @@ -82,9 +82,9 @@ enum osd_pix_format { PIXFMT_4BPP, PIXFMT_8BPP, PIXFMT_RGB565, - PIXFMT_YCbCrI, + PIXFMT_YCBCRI, PIXFMT_RGB888, - PIXFMT_YCrCbI, + PIXFMT_YCRCBI, PIXFMT_NV12, PIXFMT_OSD_ATTR, }; diff --git a/include/media/davinci/vpfe_capture.h b/include/media/davinci/vpfe_capture.h index cc973ed845a..288772e6900 100644 --- a/include/media/davinci/vpfe_capture.h +++ b/include/media/davinci/vpfe_capture.h @@ -26,6 +26,7 @@ #include <linux/videodev2.h> #include <linux/clk.h> #include <linux/i2c.h> +#include <media/v4l2-fh.h> #include <media/v4l2-ioctl.h> #include <media/v4l2-device.h> #include <media/videobuf-dma-contig.h> @@ -110,8 +111,6 @@ struct vpfe_device { struct v4l2_device v4l2_dev; /* parent device */ struct device *pdev; - /* Used to keep track of state of the priority */ - struct v4l2_prio_state prio; /* number of open instances of the channel */ u32 usrs; /* Indicates id of the field which is being displayed */ @@ -174,11 +173,10 @@ struct vpfe_device { /* File handle structure */ struct vpfe_fh { + struct v4l2_fh fh; struct vpfe_device *vpfe_dev; /* Indicates whether this file handle is doing IO */ u8 io_allowed; - /* Used to keep track priority of this instance */ - enum v4l2_priority prio; }; struct vpfe_config_params { diff --git a/include/media/davinci/vpif_types.h b/include/media/davinci/vpif_types.h index 3882e0675cc..3cb1704a065 100644 --- a/include/media/davinci/vpif_types.h +++ b/include/media/davinci/vpif_types.h @@ -59,6 +59,8 @@ struct vpif_display_config { int subdev_count; struct vpif_display_chan_config chan_config[VPIF_DISPLAY_MAX_CHANNELS]; const char *card_name; + struct v4l2_async_subdev **asd; /* Flat array, arranged in groups */ + int *asd_sizes; /* 0-terminated array of asd group sizes */ }; struct vpif_input { @@ -81,5 +83,7 @@ struct vpif_capture_config { struct vpif_subdev_info *subdev_info; int subdev_count; const char *card_name; + struct v4l2_async_subdev **asd; /* Flat array, arranged in groups */ + int *asd_sizes; /* 0-terminated array of asd group sizes */ }; #endif /* _VPIF_TYPES_H */ diff --git a/include/media/s5p_fimc.h b/include/media/exynos-fimc.h index f50969025ef..aa44660e204 100644 --- a/include/media/s5p_fimc.h +++ b/include/media/exynos-fimc.h @@ -13,6 +13,7 @@ #define S5P_FIMC_H_ #include <media/media-entity.h> +#include <media/v4l2-dev.h> #include <media/v4l2-mediabus.h> /* @@ -60,41 +61,20 @@ enum fimc_bus_type { #define GRP_ID_FLITE (1 << 13) #define GRP_ID_FIMC_IS (1 << 14) -struct i2c_board_info; - /** * struct fimc_source_info - video source description required for the host * interface configuration * - * @board_info: pointer to I2C subdevice's board info - * @clk_frequency: frequency of the clock the host interface provides to sensor * @fimc_bus_type: FIMC camera input type * @sensor_bus_type: image sensor bus type, MIPI, ITU-R BT.601 etc. * @flags: the parallel sensor bus flags defining signals polarity (V4L2_MBUS_*) - * @i2c_bus_num: i2c control bus id the sensor is attached to * @mux_id: FIMC camera interface multiplexer index (separate for MIPI and ITU) - * @clk_id: index of the SoC peripheral clock for sensors */ struct fimc_source_info { - struct i2c_board_info *board_info; - unsigned long clk_frequency; enum fimc_bus_type fimc_bus_type; enum fimc_bus_type sensor_bus_type; u16 flags; - u16 i2c_bus_num; u16 mux_id; - u8 clk_id; -}; - -/** - * struct s5p_platform_fimc - camera host interface platform data - * - * @source_info: properties of an image source for the host interface setup - * @num_clients: the number of attached image sources - */ -struct s5p_platform_fimc { - struct fimc_source_info *source_info; - int num_clients; }; /* @@ -115,6 +95,7 @@ struct s5p_platform_fimc { * @color: the driver's private color format id * @memplanes: number of physically non-contiguous data planes * @colplanes: number of physically contiguous data planes + * @colorspace: v4l2 colorspace (V4L2_COLORSPACE_*) * @depth: per plane driver's private 'number of bits per pixel' * @mdataplanes: bitmask indicating meta data plane(s), (1 << plane_no) * @flags: flags indicating which operation mode format applies to @@ -126,6 +107,7 @@ struct fimc_fmt { u32 color; u16 memplanes; u16 colplanes; + u8 colorspace; u8 depth[FIMC_MAX_PLANES]; u16 mdataplanes; u16 flags; @@ -140,37 +122,40 @@ struct fimc_fmt { #define FMT_FLAGS_YUV (1 << 7) }; -enum fimc_subdev_index { - IDX_SENSOR, - IDX_CSIS, - IDX_FLITE, - IDX_IS_ISP, - IDX_FIMC, - IDX_MAX, -}; +struct exynos_media_pipeline; -struct media_pipeline; -struct v4l2_subdev; +/* + * Media pipeline operations to be called from within a video node, i.e. the + * last entity within the pipeline. Implemented by related media device driver. + */ +struct exynos_media_pipeline_ops { + int (*prepare)(struct exynos_media_pipeline *p, + struct media_entity *me); + int (*unprepare)(struct exynos_media_pipeline *p); + int (*open)(struct exynos_media_pipeline *p, struct media_entity *me, + bool resume); + int (*close)(struct exynos_media_pipeline *p); + int (*set_stream)(struct exynos_media_pipeline *p, bool state); +}; -struct fimc_pipeline { - struct v4l2_subdev *subdevs[IDX_MAX]; - struct media_pipeline *m_pipeline; +struct exynos_video_entity { + struct video_device vdev; + struct exynos_media_pipeline *pipe; }; -/* - * Media pipeline operations to be called from within the fimc(-lite) - * video node when it is the last entity of the pipeline. Implemented - * by corresponding media device driver. - */ -struct fimc_pipeline_ops { - int (*open)(struct fimc_pipeline *p, struct media_entity *me, - bool resume); - int (*close)(struct fimc_pipeline *p); - int (*set_stream)(struct fimc_pipeline *p, bool state); +struct exynos_media_pipeline { + struct media_pipeline mp; + const struct exynos_media_pipeline_ops *ops; }; -#define fimc_pipeline_call(f, op, p, args...) \ - (!(f) ? -ENODEV : (((f)->pipeline_ops && (f)->pipeline_ops->op) ? \ - (f)->pipeline_ops->op((p), ##args) : -ENOIOCTLCMD)) +static inline struct exynos_video_entity *vdev_to_exynos_video_entity( + struct video_device *vdev) +{ + return container_of(vdev, struct exynos_video_entity, vdev); +} + +#define fimc_pipeline_call(ent, op, args...) \ + (!(ent) ? -ENOENT : (((ent)->pipe->ops && (ent)->pipe->ops->op) ? \ + (ent)->pipe->ops->op(((ent)->pipe), ##args) : -ENOIOCTLCMD)) \ #endif /* S5P_FIMC_H_ */ diff --git a/include/media/lirc_dev.h b/include/media/lirc_dev.h index 168dd0b1bae..78f0637ca68 100644 --- a/include/media/lirc_dev.h +++ b/include/media/lirc_dev.h @@ -139,6 +139,7 @@ struct lirc_driver { struct lirc_buffer *rbuf; int (*set_use_inc) (void *data); void (*set_use_dec) (void *data); + struct rc_dev *rdev; const struct file_operations *fops; struct device *dev; struct module *owner; diff --git a/include/media/lm3560.h b/include/media/lm3560.h new file mode 100644 index 00000000000..46670706d6f --- /dev/null +++ b/include/media/lm3560.h @@ -0,0 +1,97 @@ +/* + * include/media/lm3560.h + * + * Copyright (C) 2013 Texas Instruments + * + * Contact: Daniel Jeong <gshark.jeong@gmail.com> + * Ldd-Mlp <ldd-mlp@list.ti.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA + * 02110-1301 USA + * + */ + +#ifndef __LM3560_H__ +#define __LM3560_H__ + +#include <media/v4l2-subdev.h> + +#define LM3560_NAME "lm3560" +#define LM3560_I2C_ADDR (0x53) + +/* FLASH Brightness + * min 62500uA, step 62500uA, max 1000000uA + */ +#define LM3560_FLASH_BRT_MIN 62500 +#define LM3560_FLASH_BRT_STEP 62500 +#define LM3560_FLASH_BRT_MAX 1000000 +#define LM3560_FLASH_BRT_uA_TO_REG(a) \ + ((a) < LM3560_FLASH_BRT_MIN ? 0 : \ + (((a) - LM3560_FLASH_BRT_MIN) / LM3560_FLASH_BRT_STEP)) +#define LM3560_FLASH_BRT_REG_TO_uA(a) \ + ((a) * LM3560_FLASH_BRT_STEP + LM3560_FLASH_BRT_MIN) + +/* FLASH TIMEOUT DURATION + * min 32ms, step 32ms, max 1024ms + */ +#define LM3560_FLASH_TOUT_MIN 32 +#define LM3560_FLASH_TOUT_STEP 32 +#define LM3560_FLASH_TOUT_MAX 1024 +#define LM3560_FLASH_TOUT_ms_TO_REG(a) \ + ((a) < LM3560_FLASH_TOUT_MIN ? 0 : \ + (((a) - LM3560_FLASH_TOUT_MIN) / LM3560_FLASH_TOUT_STEP)) +#define LM3560_FLASH_TOUT_REG_TO_ms(a) \ + ((a) * LM3560_FLASH_TOUT_STEP + LM3560_FLASH_TOUT_MIN) + +/* TORCH BRT + * min 31250uA, step 31250uA, max 250000uA + */ +#define LM3560_TORCH_BRT_MIN 31250 +#define LM3560_TORCH_BRT_STEP 31250 +#define LM3560_TORCH_BRT_MAX 250000 +#define LM3560_TORCH_BRT_uA_TO_REG(a) \ + ((a) < LM3560_TORCH_BRT_MIN ? 0 : \ + (((a) - LM3560_TORCH_BRT_MIN) / LM3560_TORCH_BRT_STEP)) +#define LM3560_TORCH_BRT_REG_TO_uA(a) \ + ((a) * LM3560_TORCH_BRT_STEP + LM3560_TORCH_BRT_MIN) + +enum lm3560_led_id { + LM3560_LED0 = 0, + LM3560_LED1, + LM3560_LED_MAX +}; + +enum lm3560_peak_current { + LM3560_PEAK_1600mA = 0x00, + LM3560_PEAK_2300mA = 0x20, + LM3560_PEAK_3000mA = 0x40, + LM3560_PEAK_3600mA = 0x60 +}; + +/* struct lm3560_platform_data + * + * @peak : peak current + * @max_flash_timeout: flash timeout + * @max_flash_brt: flash mode led brightness + * @max_torch_brt: torch mode led brightness + */ +struct lm3560_platform_data { + enum lm3560_peak_current peak; + + u32 max_flash_timeout; + u32 max_flash_brt[LM3560_LED_MAX]; + u32 max_torch_brt[LM3560_LED_MAX]; +}; + +#endif /* __LM3560_H__ */ diff --git a/include/media/lm3646.h b/include/media/lm3646.h new file mode 100644 index 00000000000..c6acf5a1d64 --- /dev/null +++ b/include/media/lm3646.h @@ -0,0 +1,87 @@ +/* + * include/media/lm3646.h + * + * Copyright (C) 2014 Texas Instruments + * + * Contact: Daniel Jeong <gshark.jeong@gmail.com> + * Ldd-Mlp <ldd-mlp@list.ti.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + */ + +#ifndef __LM3646_H__ +#define __LM3646_H__ + +#include <media/v4l2-subdev.h> + +#define LM3646_NAME "lm3646" +#define LM3646_I2C_ADDR_REV1 (0x67) +#define LM3646_I2C_ADDR_REV0 (0x63) + +/* TOTAL FLASH Brightness Max + * min 93350uA, step 93750uA, max 1499600uA + */ +#define LM3646_TOTAL_FLASH_BRT_MIN 93350 +#define LM3646_TOTAL_FLASH_BRT_STEP 93750 +#define LM3646_TOTAL_FLASH_BRT_MAX 1499600 +#define LM3646_TOTAL_FLASH_BRT_uA_TO_REG(a) \ + ((a) < LM3646_TOTAL_FLASH_BRT_MIN ? 0 : \ + ((((a) - LM3646_TOTAL_FLASH_BRT_MIN) / LM3646_TOTAL_FLASH_BRT_STEP))) + +/* TOTAL TORCH Brightness Max + * min 23040uA, step 23430uA, max 187100uA + */ +#define LM3646_TOTAL_TORCH_BRT_MIN 23040 +#define LM3646_TOTAL_TORCH_BRT_STEP 23430 +#define LM3646_TOTAL_TORCH_BRT_MAX 187100 +#define LM3646_TOTAL_TORCH_BRT_uA_TO_REG(a) \ + ((a) < LM3646_TOTAL_TORCH_BRT_MIN ? 0 : \ + ((((a) - LM3646_TOTAL_TORCH_BRT_MIN) / LM3646_TOTAL_TORCH_BRT_STEP))) + +/* LED1 FLASH Brightness + * min 23040uA, step 11718uA, max 1499600uA + */ +#define LM3646_LED1_FLASH_BRT_MIN 23040 +#define LM3646_LED1_FLASH_BRT_STEP 11718 +#define LM3646_LED1_FLASH_BRT_MAX 1499600 +#define LM3646_LED1_FLASH_BRT_uA_TO_REG(a) \ + ((a) <= LM3646_LED1_FLASH_BRT_MIN ? 0 : \ + ((((a) - LM3646_LED1_FLASH_BRT_MIN) / LM3646_LED1_FLASH_BRT_STEP))+1) + +/* LED1 TORCH Brightness + * min 2530uA, step 1460uA, max 187100uA + */ +#define LM3646_LED1_TORCH_BRT_MIN 2530 +#define LM3646_LED1_TORCH_BRT_STEP 1460 +#define LM3646_LED1_TORCH_BRT_MAX 187100 +#define LM3646_LED1_TORCH_BRT_uA_TO_REG(a) \ + ((a) <= LM3646_LED1_TORCH_BRT_MIN ? 0 : \ + ((((a) - LM3646_LED1_TORCH_BRT_MIN) / LM3646_LED1_TORCH_BRT_STEP))+1) + +/* FLASH TIMEOUT DURATION + * min 50ms, step 50ms, max 400ms + */ +#define LM3646_FLASH_TOUT_MIN 50 +#define LM3646_FLASH_TOUT_STEP 50 +#define LM3646_FLASH_TOUT_MAX 400 +#define LM3646_FLASH_TOUT_ms_TO_REG(a) \ + ((a) <= LM3646_FLASH_TOUT_MIN ? 0 : \ + (((a) - LM3646_FLASH_TOUT_MIN) / LM3646_FLASH_TOUT_STEP)) + +/* struct lm3646_platform_data + * + * @flash_timeout: flash timeout + * @led1_flash_brt: led1 flash mode brightness, uA + * @led1_torch_brt: led1 torch mode brightness, uA + */ +struct lm3646_platform_data { + + u32 flash_timeout; + + u32 led1_flash_brt; + u32 led1_torch_brt; +}; + +#endif /* __LM3646_H__ */ diff --git a/include/media/media-device.h b/include/media/media-device.h index eaade9815bb..6e6db78f1ee 100644 --- a/include/media/media-device.h +++ b/include/media/media-device.h @@ -45,6 +45,7 @@ struct device; * @entities: List of registered entities * @lock: Entities list lock * @graph_mutex: Entities graph operation lock + * @link_notify: Link state change notification callback * * This structure represents an abstract high-level media device. It allows easy * access to entities and provides basic media device-level support. The @@ -75,14 +76,20 @@ struct media_device { /* Serializes graph operations. */ struct mutex graph_mutex; - int (*link_notify)(struct media_pad *source, - struct media_pad *sink, u32 flags); + int (*link_notify)(struct media_link *link, u32 flags, + unsigned int notification); }; +/* Supported link_notify @notification values. */ +#define MEDIA_DEV_NOTIFY_PRE_LINK_CH 0 +#define MEDIA_DEV_NOTIFY_POST_LINK_CH 1 + /* media_devnode to media_device */ #define to_media_device(node) container_of(node, struct media_device, devnode) -int __must_check media_device_register(struct media_device *mdev); +int __must_check __media_device_register(struct media_device *mdev, + struct module *owner); +#define media_device_register(mdev) __media_device_register(mdev, THIS_MODULE) void media_device_unregister(struct media_device *mdev); int __must_check media_device_register_entity(struct media_device *mdev, diff --git a/include/media/media-devnode.h b/include/media/media-devnode.h index 3446af279fc..0dc7060f962 100644 --- a/include/media/media-devnode.h +++ b/include/media/media-devnode.h @@ -82,7 +82,8 @@ struct media_devnode { /* dev to media_devnode */ #define to_media_devnode(cd) container_of(cd, struct media_devnode, dev) -int __must_check media_devnode_register(struct media_devnode *mdev); +int __must_check media_devnode_register(struct media_devnode *mdev, + struct module *owner); void media_devnode_unregister(struct media_devnode *mdev); static inline struct media_devnode *media_devnode_data(struct file *filp) diff --git a/include/media/media-entity.h b/include/media/media-entity.h index 0c16f518ee0..e00459185d2 100644 --- a/include/media/media-entity.h +++ b/include/media/media-entity.h @@ -23,6 +23,8 @@ #ifndef _MEDIA_ENTITY_H #define _MEDIA_ENTITY_H +#include <linux/bitops.h> +#include <linux/kernel.h> #include <linux/list.h> #include <linux/media.h> @@ -113,12 +115,15 @@ static inline u32 media_entity_subtype(struct media_entity *entity) } #define MEDIA_ENTITY_ENUM_MAX_DEPTH 16 +#define MEDIA_ENTITY_ENUM_MAX_ID 64 struct media_entity_graph { struct { struct media_entity *entity; int link; } stack[MEDIA_ENTITY_ENUM_MAX_DEPTH]; + + DECLARE_BITMAP(entities, MEDIA_ENTITY_ENUM_MAX_ID); int top; }; @@ -128,11 +133,14 @@ void media_entity_cleanup(struct media_entity *entity); int media_entity_create_link(struct media_entity *source, u16 source_pad, struct media_entity *sink, u16 sink_pad, u32 flags); +void __media_entity_remove_links(struct media_entity *entity); +void media_entity_remove_links(struct media_entity *entity); + int __media_entity_setup_link(struct media_link *link, u32 flags); int media_entity_setup_link(struct media_link *link, u32 flags); struct media_link *media_entity_find_link(struct media_pad *source, struct media_pad *sink); -struct media_pad *media_entity_remote_source(struct media_pad *pad); +struct media_pad *media_entity_remote_pad(struct media_pad *pad); struct media_entity *media_entity_get(struct media_entity *entity); void media_entity_put(struct media_entity *entity); diff --git a/include/media/mt9v032.h b/include/media/mt9v032.h index 78fd39eac21..12175a63c5b 100644 --- a/include/media/mt9v032.h +++ b/include/media/mt9v032.h @@ -1,13 +1,9 @@ #ifndef _MEDIA_MT9V032_H #define _MEDIA_MT9V032_H -struct v4l2_subdev; - struct mt9v032_platform_data { unsigned int clk_pol:1; - void (*set_clock)(struct v4l2_subdev *subdev, unsigned int rate); - const s64 *link_freqs; s64 link_def_freq; }; diff --git a/include/media/omap4iss.h b/include/media/omap4iss.h new file mode 100644 index 00000000000..0d7620db5e3 --- /dev/null +++ b/include/media/omap4iss.h @@ -0,0 +1,65 @@ +#ifndef ARCH_ARM_PLAT_OMAP4_ISS_H +#define ARCH_ARM_PLAT_OMAP4_ISS_H + +#include <linux/i2c.h> + +struct iss_device; + +enum iss_interface_type { + ISS_INTERFACE_CSI2A_PHY1, + ISS_INTERFACE_CSI2B_PHY2, +}; + +/** + * struct iss_csiphy_lane: CSI2 lane position and polarity + * @pos: position of the lane + * @pol: polarity of the lane + */ +struct iss_csiphy_lane { + u8 pos; + u8 pol; +}; + +#define ISS_CSIPHY1_NUM_DATA_LANES 4 +#define ISS_CSIPHY2_NUM_DATA_LANES 1 + +/** + * struct iss_csiphy_lanes_cfg - CSI2 lane configuration + * @data: Configuration of one or two data lanes + * @clk: Clock lane configuration + */ +struct iss_csiphy_lanes_cfg { + struct iss_csiphy_lane data[ISS_CSIPHY1_NUM_DATA_LANES]; + struct iss_csiphy_lane clk; +}; + +/** + * struct iss_csi2_platform_data - CSI2 interface platform data + * @crc: Enable the cyclic redundancy check + * @vpclk_div: Video port output clock control + */ +struct iss_csi2_platform_data { + unsigned crc:1; + unsigned vpclk_div:2; + struct iss_csiphy_lanes_cfg lanecfg; +}; + +struct iss_subdev_i2c_board_info { + struct i2c_board_info *board_info; + int i2c_adapter_id; +}; + +struct iss_v4l2_subdevs_group { + struct iss_subdev_i2c_board_info *subdevs; + enum iss_interface_type interface; + union { + struct iss_csi2_platform_data csi2; + } bus; /* gcc < 4.6.0 chokes on anonymous union initializers */ +}; + +struct iss_platform_data { + struct iss_v4l2_subdevs_group *subdevs; + void (*set_constraints)(struct iss_device *iss, bool enable); +}; + +#endif diff --git a/include/media/rc-core.h b/include/media/rc-core.h index 06a75deff55..fde142e5f25 100644 --- a/include/media/rc-core.h +++ b/include/media/rc-core.h @@ -1,7 +1,7 @@ /* * Remote Controller core header * - * Copyright (C) 2009-2010 by Mauro Carvalho Chehab <mchehab@redhat.com> + * Copyright (C) 2009-2010 by Mauro Carvalho Chehab * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -35,8 +35,32 @@ enum rc_driver_type { }; /** + * struct rc_scancode_filter - Filter scan codes. + * @data: Scancode data to match. + * @mask: Mask of bits of scancode to compare. + */ +struct rc_scancode_filter { + u32 data; + u32 mask; +}; + +/** + * enum rc_filter_type - Filter type constants. + * @RC_FILTER_NORMAL: Filter for normal operation. + * @RC_FILTER_WAKEUP: Filter for waking from suspend. + * @RC_FILTER_MAX: Number of filter types. + */ +enum rc_filter_type { + RC_FILTER_NORMAL = 0, + RC_FILTER_WAKEUP, + + RC_FILTER_MAX +}; + +/** * struct rc_dev - represents a remote control device * @dev: driver model's view of this device + * @sysfs_groups: sysfs attribute groups * @input_name: name of the input child device * @input_phys: physical path to the input child device * @input_id: id of the input child device (struct input_id) @@ -50,8 +74,10 @@ enum rc_driver_type { * @input_dev: the input child device used to communicate events to userspace * @driver_type: specifies if protocol decoding is done in hardware or software * @idle: used to keep track of RX state - * @allowed_protos: bitmask with the supported RC_BIT_* protocols - * @enabled_protocols: bitmask with the enabled RC_BIT_* protocols + * @allowed_protocols: bitmask with the supported RC_BIT_* protocols for each + * filter type + * @enabled_protocols: bitmask with the enabled RC_BIT_* protocols for each + * filter type * @scanmask: some hardware decoders are not capable of providing the full * scancode to the application. As this is a hardware limit, we can't do * anything with it. Yet, as the same keycode table can be used with other @@ -70,7 +96,10 @@ enum rc_driver_type { * @max_timeout: maximum timeout supported by device * @rx_resolution : resolution (in ns) of input sampler * @tx_resolution: resolution (in ns) of output sampler + * @scancode_filters: scancode filters (indexed by enum rc_filter_type) * @change_protocol: allow changing the protocol used on hardware decoders + * @change_wakeup_protocol: allow changing the protocol used for wakeup + * filtering * @open: callback to allow drivers to enable polling/irq when IR input device * is opened. * @close: callback to allow drivers to disable polling/irq when IR input device @@ -84,9 +113,12 @@ enum rc_driver_type { * device doesn't interrupt host until it sees IR pulses * @s_learning_mode: enable wide band receiver used for learning * @s_carrier_report: enable carrier reports + * @s_filter: set the scancode filter + * @s_wakeup_filter: set the wakeup scancode filter */ struct rc_dev { struct device dev; + const struct attribute_group *sysfs_groups[5]; const char *input_name; const char *input_phys; struct input_id input_id; @@ -99,8 +131,9 @@ struct rc_dev { struct input_dev *input_dev; enum rc_driver_type driver_type; bool idle; - u64 allowed_protos; - u64 enabled_protocols; + u64 allowed_protocols[RC_FILTER_MAX]; + u64 enabled_protocols[RC_FILTER_MAX]; + u32 users; u32 scanmask; void *priv; spinlock_t keylock; @@ -115,7 +148,9 @@ struct rc_dev { u32 max_timeout; u32 rx_resolution; u32 tx_resolution; + struct rc_scancode_filter scancode_filters[RC_FILTER_MAX]; int (*change_protocol)(struct rc_dev *dev, u64 *rc_type); + int (*change_wakeup_protocol)(struct rc_dev *dev, u64 *rc_type); int (*open)(struct rc_dev *dev); void (*close)(struct rc_dev *dev); int (*s_tx_mask)(struct rc_dev *dev, u32 mask); @@ -126,10 +161,50 @@ struct rc_dev { void (*s_idle)(struct rc_dev *dev, bool enable); int (*s_learning_mode)(struct rc_dev *dev, int enable); int (*s_carrier_report) (struct rc_dev *dev, int enable); + int (*s_filter)(struct rc_dev *dev, + struct rc_scancode_filter *filter); + int (*s_wakeup_filter)(struct rc_dev *dev, + struct rc_scancode_filter *filter); }; #define to_rc_dev(d) container_of(d, struct rc_dev, dev) +static inline bool rc_protocols_allowed(struct rc_dev *rdev, u64 protos) +{ + return rdev->allowed_protocols[RC_FILTER_NORMAL] & protos; +} + +/* should be called prior to registration or with mutex held */ +static inline void rc_set_allowed_protocols(struct rc_dev *rdev, u64 protos) +{ + rdev->allowed_protocols[RC_FILTER_NORMAL] = protos; +} + +static inline bool rc_protocols_enabled(struct rc_dev *rdev, u64 protos) +{ + return rdev->enabled_protocols[RC_FILTER_NORMAL] & protos; +} + +/* should be called prior to registration or with mutex held */ +static inline void rc_set_enabled_protocols(struct rc_dev *rdev, u64 protos) +{ + rdev->enabled_protocols[RC_FILTER_NORMAL] = protos; +} + +/* should be called prior to registration or with mutex held */ +static inline void rc_set_allowed_wakeup_protocols(struct rc_dev *rdev, + u64 protos) +{ + rdev->allowed_protocols[RC_FILTER_WAKEUP] = protos; +} + +/* should be called prior to registration or with mutex held */ +static inline void rc_set_enabled_wakeup_protocols(struct rc_dev *rdev, + u64 protos) +{ + rdev->enabled_protocols[RC_FILTER_WAKEUP] = protos; +} + /* * From rc-main.c * Those functions can be used on any type of Remote Controller. They @@ -142,6 +217,9 @@ void rc_free_device(struct rc_dev *dev); int rc_register_device(struct rc_dev *dev); void rc_unregister_device(struct rc_dev *dev); +int rc_open(struct rc_dev *rdev); +void rc_close(struct rc_dev *rdev); + void rc_repeat(struct rc_dev *dev); void rc_keydown(struct rc_dev *dev, int scancode, u8 toggle); void rc_keydown_notimeout(struct rc_dev *dev, int scancode, u8 toggle); diff --git a/include/media/rc-map.h b/include/media/rc-map.h index 5d5d3a30f04..e5aa2409c0e 100644 --- a/include/media/rc-map.h +++ b/include/media/rc-map.h @@ -1,7 +1,7 @@ /* * rc-map.h - define RC map names used by RC drivers * - * Copyright (c) 2010 by Mauro Carvalho Chehab <mchehab@redhat.com> + * Copyright (c) 2010 by Mauro Carvalho Chehab * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -30,6 +30,7 @@ enum rc_type { RC_TYPE_RC6_6A_24 = 15, /* Philips RC6-6A-24 protocol */ RC_TYPE_RC6_6A_32 = 16, /* Philips RC6-6A-32 protocol */ RC_TYPE_RC6_MCE = 17, /* MCE (Philips RC6-6A-32 subtype) protocol */ + RC_TYPE_SHARP = 18, /* Sharp protocol */ }; #define RC_BIT_NONE 0 @@ -51,6 +52,7 @@ enum rc_type { #define RC_BIT_RC6_6A_24 (1 << RC_TYPE_RC6_6A_24) #define RC_BIT_RC6_6A_32 (1 << RC_TYPE_RC6_6A_32) #define RC_BIT_RC6_MCE (1 << RC_TYPE_RC6_MCE) +#define RC_BIT_SHARP (1 << RC_TYPE_SHARP) #define RC_BIT_ALL (RC_BIT_UNKNOWN | RC_BIT_OTHER | RC_BIT_LIRC | \ RC_BIT_RC5 | RC_BIT_RC5X | RC_BIT_RC5_SZ | \ @@ -58,7 +60,7 @@ enum rc_type { RC_BIT_SONY12 | RC_BIT_SONY15 | RC_BIT_SONY20 | \ RC_BIT_NEC | RC_BIT_SANYO | RC_BIT_MCE_KBD | \ RC_BIT_RC6_0 | RC_BIT_RC6_6A_20 | RC_BIT_RC6_6A_24 | \ - RC_BIT_RC6_6A_32 | RC_BIT_RC6_MCE) + RC_BIT_RC6_6A_32 | RC_BIT_RC6_MCE | RC_BIT_SHARP) struct rc_map_table { u32 scancode; @@ -111,6 +113,7 @@ void rc_map_init(void); #define RC_MAP_BUDGET_CI_OLD "rc-budget-ci-old" #define RC_MAP_CINERGY_1400 "rc-cinergy-1400" #define RC_MAP_CINERGY "rc-cinergy" +#define RC_MAP_DELOCK_61959 "rc-delock-61959" #define RC_MAP_DIB0700_NEC_TABLE "rc-dib0700-nec" #define RC_MAP_DIB0700_RC5_TABLE "rc-dib0700-rc5" #define RC_MAP_DIGITALNOW_TINYTWIN "rc-digitalnow-tinytwin" @@ -192,6 +195,7 @@ void rc_map_init(void); #define RC_MAP_VIDEOMATE_TV_PVR "rc-videomate-tv-pvr" #define RC_MAP_WINFAST "rc-winfast" #define RC_MAP_WINFAST_USBII_DELUXE "rc-winfast-usbii-deluxe" +#define RC_MAP_SU3000 "rc-su3000" /* * Please, do not just append newer Remote Controller names at the end. diff --git a/include/media/saa6588.h b/include/media/saa6588.h index 2c3c4420a4e..b5ec1aa60ed 100644 --- a/include/media/saa6588.h +++ b/include/media/saa6588.h @@ -27,6 +27,7 @@ struct saa6588_command { unsigned int block_count; + bool nonblocking; int result; unsigned char __user *buffer; struct file *instance; @@ -34,7 +35,6 @@ struct saa6588_command { }; /* These ioctls are internal to the kernel */ -#define SAA6588_CMD_OPEN _IOW('R', 1, int) #define SAA6588_CMD_CLOSE _IOW('R', 2, int) #define SAA6588_CMD_READ _IOR('R', 3, int) #define SAA6588_CMD_POLL _IOR('R', 4, int) diff --git a/include/media/saa6752hs.h b/include/media/saa6752hs.h deleted file mode 100644 index 3b8686ead80..00000000000 --- a/include/media/saa6752hs.h +++ /dev/null @@ -1,26 +0,0 @@ -/* - saa6752hs.h - definition for saa6752hs MPEG encoder - - Copyright (C) 2003 Andrew de Quincey <adq@lidskialf.net> - - This program is free software; you can redistribute it and/or modify - it under the terms of the GNU General Public License as published by - the Free Software Foundation; either version 2 of the License, or - (at your option) any later version. - - This program is distributed in the hope that it will be useful, - but WITHOUT ANY WARRANTY; without even the implied warranty of - MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. -*/ - - -/* - * Local variables: - * c-basic-offset: 8 - * End: - */ diff --git a/include/media/saa7115.h b/include/media/saa7115.h index 407918625c8..76911e71de1 100644 --- a/include/media/saa7115.h +++ b/include/media/saa7115.h @@ -47,9 +47,11 @@ #define SAA7111_FMT_YUV411 0xc0 /* config flags */ -/* Register 0x85 should set bit 0 to 0 (it's 1 by default). This bit +/* + * Register 0x85 should set bit 0 to 0 (it's 1 by default). This bit * controls the IDQ signal polarity which is set to 'inverted' if the bit - * it 1 and to 'default' if it is 0. */ + * it 1 and to 'default' if it is 0. + */ #define SAA7115_IDQ_IS_DEFAULT (1 << 0) /* s_crystal_freq values and flags */ @@ -64,5 +66,76 @@ #define SAA7115_FREQ_FL_APLL (1 << 2) /* SA 3A[3], APLL, SAA7114/5 only */ #define SAA7115_FREQ_FL_DOUBLE_ASCLK (1 << 3) /* SA 39, LRDIV, SAA7114/5 only */ +/* ===== SAA7113 Config enums ===== */ + +/* Register 0x08 "Horizontal time constant" [Bit 3..4]: + * Should be set to "Fast Locking Mode" according to the datasheet, + * and that is the default setting in the gm7113c_init table. + * saa7113_init sets this value to "VTR Mode". */ +enum saa7113_r08_htc { + SAA7113_HTC_TV_MODE = 0x00, + SAA7113_HTC_VTR_MODE, /* Default for saa7113_init */ + SAA7113_HTC_FAST_LOCKING_MODE = 0x03 /* Default for gm7113c_init */ +}; + +/* Register 0x10 "Output format selection" [Bit 6..7]: + * Defaults to ITU_656 as specified in datasheet. */ +enum saa7113_r10_ofts { + SAA7113_OFTS_ITU_656 = 0x0, /* Default */ + SAA7113_OFTS_VFLAG_BY_VREF, + SAA7113_OFTS_VFLAG_BY_DATA_TYPE +}; + +/* + * Register 0x12 "Output control" [Bit 0..3 Or Bit 4..7]: + * This is used to select what data is output on the RTS0 and RTS1 pins. + * RTS1 [Bit 4..7] Defaults to DOT_IN. (This value can not be set for RTS0) + * RTS0 [Bit 0..3] Defaults to VIPB in gm7113c_init as specified + * in the datasheet, but is set to HREF_HS in the saa7113_init table. + */ +enum saa7113_r12_rts { + SAA7113_RTS_DOT_IN = 0, /* OBS: Only for RTS1 (Default RTS1) */ + SAA7113_RTS_VIPB, /* Default RTS0 For gm7113c_init */ + SAA7113_RTS_GPSW, + SAA7115_RTS_HL, + SAA7113_RTS_VL, + SAA7113_RTS_DL, + SAA7113_RTS_PLIN, + SAA7113_RTS_HREF_HS, /* Default RTS0 For saa7113_init */ + SAA7113_RTS_HS, + SAA7113_RTS_HQ, + SAA7113_RTS_ODD, + SAA7113_RTS_VS, + SAA7113_RTS_V123, + SAA7113_RTS_VGATE, + SAA7113_RTS_VREF, + SAA7113_RTS_FID +}; + +/** + * struct saa7115_platform_data - Allow overriding default initialization + * + * @saa7113_force_gm7113c_init: Force the use of the gm7113c_init table + * instead of saa7113_init table + * (saa7113 only) + * @saa7113_r08_htc: [R_08 - Bit 3..4] + * @saa7113_r10_vrln: [R_10 - Bit 3] + * default: Disabled for gm7113c_init + * Enabled for saa7113c_init + * @saa7113_r10_ofts: [R_10 - Bit 6..7] + * @saa7113_r12_rts0: [R_12 - Bit 0..3] + * @saa7113_r12_rts1: [R_12 - Bit 4..7] + * @saa7113_r13_adlsb: [R_13 - Bit 7] - default: disabled + */ +struct saa7115_platform_data { + bool saa7113_force_gm7113c_init; + enum saa7113_r08_htc *saa7113_r08_htc; + bool *saa7113_r10_vrln; + enum saa7113_r10_ofts *saa7113_r10_ofts; + enum saa7113_r12_rts *saa7113_r12_rts0; + enum saa7113_r12_rts *saa7113_r12_rts1; + bool *saa7113_r13_adlsb; +}; + #endif diff --git a/include/media/sh_mobile_ceu.h b/include/media/sh_mobile_ceu.h index 6fdb6adf6b2..7f57056c22b 100644 --- a/include/media/sh_mobile_ceu.h +++ b/include/media/sh_mobile_ceu.h @@ -22,6 +22,8 @@ struct sh_mobile_ceu_info { int max_width; int max_height; struct sh_mobile_ceu_companion *csi2; + struct v4l2_async_subdev **asd; /* Flat array, arranged in groups */ + unsigned int *asd_sizes; /* 0-terminated array pf asd group sizes */ }; #endif /* __ASM_SH_MOBILE_CEU_H__ */ diff --git a/include/media/sh_mobile_csi2.h b/include/media/sh_mobile_csi2.h index c586c4f7f16..14030db51f1 100644 --- a/include/media/sh_mobile_csi2.h +++ b/include/media/sh_mobile_csi2.h @@ -33,6 +33,7 @@ struct sh_csi2_client_config { unsigned char lanes; /* bitmask[3:0] */ unsigned char channel; /* 0..3 */ struct platform_device *pdev; /* client platform device */ + const char *name; /* async matching: client name */ }; struct v4l2_device; @@ -42,7 +43,6 @@ struct sh_csi2_pdata { unsigned int flags; struct sh_csi2_client_config *clients; int num_clients; - struct v4l2_device *v4l2_dev; }; #endif diff --git a/include/media/si4713.h b/include/media/si4713.h index ed7353e8a98..f98a0a7af61 100644 --- a/include/media/si4713.h +++ b/include/media/si4713.h @@ -23,6 +23,8 @@ * Platform dependent definition */ struct si4713_platform_data { + const char * const *supply_names; + unsigned supplies; int gpio_reset; /* < 0 if not used */ }; diff --git a/include/media/smiapp.h b/include/media/smiapp.h index 07f96a89e18..0b8f124a630 100644 --- a/include/media/smiapp.h +++ b/include/media/smiapp.h @@ -77,7 +77,6 @@ struct smiapp_platform_data { struct smiapp_flash_strobe_parms *strobe_setup; int (*set_xclk)(struct v4l2_subdev *sd, int hz); - char *ext_clk_name; int xshutdown; /* gpio or SMIAPP_NO_XSHUTDOWN */ }; diff --git a/include/media/soc_camera.h b/include/media/soc_camera.h index ff77d08c30f..865246b0012 100644 --- a/include/media/soc_camera.h +++ b/include/media/soc_camera.h @@ -19,11 +19,13 @@ #include <linux/videodev2.h> #include <media/videobuf-core.h> #include <media/videobuf2-core.h> +#include <media/v4l2-async.h> #include <media/v4l2-ctrls.h> #include <media/v4l2-device.h> struct file; struct soc_camera_desc; +struct soc_camera_async_client; struct soc_camera_device { struct list_head list; /* list of all registered devices */ @@ -49,6 +51,10 @@ struct soc_camera_device { /* soc_camera.c private count. Only accessed with .host_lock held */ int use_count; struct file *streamer; /* stream owner */ + struct v4l2_clk *clk; + /* Asynchronous subdevice management */ + struct soc_camera_async_client *sasc; + /* video buffer queue */ union { struct videobuf_queue vb_vidq; struct vb2_queue vb2_vidq; @@ -58,21 +64,38 @@ struct soc_camera_device { /* Host supports programmable stride */ #define SOCAM_HOST_CAP_STRIDE (1 << 0) +enum soc_camera_subdev_role { + SOCAM_SUBDEV_DATA_SOURCE = 1, + SOCAM_SUBDEV_DATA_SINK, + SOCAM_SUBDEV_DATA_PROCESSOR, +}; + +struct soc_camera_async_subdev { + struct v4l2_async_subdev asd; + enum soc_camera_subdev_role role; +}; + struct soc_camera_host { struct v4l2_device v4l2_dev; struct list_head list; - struct mutex host_lock; /* Protect pipeline modifications */ + struct mutex host_lock; /* Main synchronisation lock */ + struct mutex clk_lock; /* Protect pipeline modifications */ unsigned char nr; /* Host number */ u32 capabilities; + struct soc_camera_device *icd; /* Currently attached client */ void *priv; const char *drv_name; struct soc_camera_host_ops *ops; + struct v4l2_async_subdev **asd; /* Flat array, arranged in groups */ + unsigned int *asd_sizes; /* 0-terminated array of asd group sizes */ }; struct soc_camera_host_ops { struct module *owner; int (*add)(struct soc_camera_device *); void (*remove)(struct soc_camera_device *); + int (*clock_start)(struct soc_camera_host *); + void (*clock_stop)(struct soc_camera_host *); /* * .get_formats() is called for each client device format, but * .put_formats() is only called once. Further, if any of the calls to @@ -123,9 +146,14 @@ struct soc_camera_subdev_desc { /* sensor driver private platform data */ void *drv_priv; - /* Optional regulators that have to be managed on power on/off events */ - struct regulator_bulk_data *regulators; - int num_regulators; + /* + * Set unbalanced_power to true to deal with legacy drivers, failing to + * balance their calls to subdevice's .s_power() method. clock_state is + * then used internally by helper functions, it shouldn't be touched by + * drivers or the platform code. + */ + bool unbalanced_power; + unsigned long clock_state; /* Optional callbacks to power on or off and reset the sensor */ int (*power)(struct device *, int); @@ -139,6 +167,9 @@ struct soc_camera_subdev_desc { int (*set_bus_param)(struct soc_camera_subdev_desc *, unsigned long flags); unsigned long (*query_bus_param)(struct soc_camera_subdev_desc *); void (*free_bus)(struct soc_camera_subdev_desc *); + + /* Optional regulators that have to be managed on power on/off events */ + struct v4l2_subdev_platform_data sd_pdata; }; struct soc_camera_host_desc { @@ -157,6 +188,7 @@ struct soc_camera_host_desc { }; /* + * Platform data for "soc-camera-pdrv" * This MUST be kept binary-identical to struct soc_camera_link below, until * it is completely replaced by this one, after which we can split it into its * two components. @@ -178,9 +210,10 @@ struct soc_camera_link { void *priv; - /* Optional regulators that have to be managed on power on/off events */ - struct regulator_bulk_data *regulators; - int num_regulators; + /* Set by platforms to handle misbehaving drivers */ + bool unbalanced_power; + /* Used by soc-camera helper functions */ + unsigned long clock_state; /* Optional callbacks to power on or off and reset the sensor */ int (*power)(struct device *, int); @@ -194,6 +227,12 @@ struct soc_camera_link { unsigned long (*query_bus_param)(struct soc_camera_link *); void (*free_bus)(struct soc_camera_link *); + /* Optional regulators that have to be managed on power on/off events */ + struct regulator_bulk_data *regulators; + int num_regulators; + + void *host_priv; + /* * Host part - keep at bottom and compatible to * struct soc_camera_host_desc @@ -322,14 +361,17 @@ static inline void soc_camera_limit_side(int *start, int *length, unsigned long soc_camera_apply_board_flags(struct soc_camera_subdev_desc *ssdd, const struct v4l2_mbus_config *cfg); -int soc_camera_power_on(struct device *dev, struct soc_camera_subdev_desc *ssdd); -int soc_camera_power_off(struct device *dev, struct soc_camera_subdev_desc *ssdd); +int soc_camera_power_init(struct device *dev, struct soc_camera_subdev_desc *ssdd); +int soc_camera_power_on(struct device *dev, struct soc_camera_subdev_desc *ssdd, + struct v4l2_clk *clk); +int soc_camera_power_off(struct device *dev, struct soc_camera_subdev_desc *ssdd, + struct v4l2_clk *clk); static inline int soc_camera_set_power(struct device *dev, - struct soc_camera_subdev_desc *ssdd, bool on) + struct soc_camera_subdev_desc *ssdd, struct v4l2_clk *clk, bool on) { - return on ? soc_camera_power_on(dev, ssdd) - : soc_camera_power_off(dev, ssdd); + return on ? soc_camera_power_on(dev, ssdd, clk) + : soc_camera_power_off(dev, ssdd, clk); } /* This is only temporary here - until v4l2-subdev begins to link to video_device */ @@ -346,9 +388,9 @@ static inline struct soc_camera_subdev_desc *soc_camera_i2c_to_desc(const struct return client->dev.platform_data; } -static inline struct v4l2_subdev *soc_camera_vdev_to_subdev(const struct video_device *vdev) +static inline struct v4l2_subdev *soc_camera_vdev_to_subdev(struct video_device *vdev) { - struct soc_camera_device *icd = dev_get_drvdata(vdev->parent); + struct soc_camera_device *icd = video_get_drvdata(vdev); return soc_camera_to_subdev(icd); } diff --git a/include/media/tea575x.h b/include/media/tea575x.h new file mode 100644 index 00000000000..2d4fa59db90 --- /dev/null +++ b/include/media/tea575x.h @@ -0,0 +1,79 @@ +#ifndef __SOUND_TEA575X_TUNER_H +#define __SOUND_TEA575X_TUNER_H + +/* + * ALSA driver for TEA5757/5759 Philips AM/FM tuner chips + * + * Copyright (c) 2004 Jaroslav Kysela <perex@perex.cz> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + */ + +#include <linux/videodev2.h> +#include <media/v4l2-ctrls.h> +#include <media/v4l2-dev.h> +#include <media/v4l2-device.h> + +#define TEA575X_FMIF 10700 +#define TEA575X_AMIF 450 + +#define TEA575X_DATA (1 << 0) +#define TEA575X_CLK (1 << 1) +#define TEA575X_WREN (1 << 2) +#define TEA575X_MOST (1 << 3) + +struct snd_tea575x; + +struct snd_tea575x_ops { + /* Drivers using snd_tea575x must either define read_ and write_val */ + void (*write_val)(struct snd_tea575x *tea, u32 val); + u32 (*read_val)(struct snd_tea575x *tea); + /* Or define the 3 pin functions */ + void (*set_pins)(struct snd_tea575x *tea, u8 pins); + u8 (*get_pins)(struct snd_tea575x *tea); + void (*set_direction)(struct snd_tea575x *tea, bool output); +}; + +struct snd_tea575x { + struct v4l2_device *v4l2_dev; + struct v4l2_file_operations fops; + struct video_device vd; /* video device */ + int radio_nr; /* radio_nr */ + bool tea5759; /* 5759 chip is present */ + bool has_am; /* Device can tune to AM freqs */ + bool cannot_read_data; /* Device cannot read the data pin */ + bool cannot_mute; /* Device cannot mute */ + bool mute; /* Device is muted? */ + bool stereo; /* receiving stereo */ + bool tuned; /* tuned to a station */ + unsigned int val; /* hw value */ + u32 band; /* 0: FM, 1: FM-Japan, 2: AM */ + u32 freq; /* frequency */ + struct mutex mutex; + struct snd_tea575x_ops *ops; + void *private_data; + u8 card[32]; + u8 bus_info[32]; + struct v4l2_ctrl_handler ctrl_handler; + int (*ext_init)(struct snd_tea575x *tea); +}; + +int snd_tea575x_hw_init(struct snd_tea575x *tea); +int snd_tea575x_init(struct snd_tea575x *tea, struct module *owner); +void snd_tea575x_exit(struct snd_tea575x *tea); +void snd_tea575x_set_freq(struct snd_tea575x *tea); + +#endif /* __SOUND_TEA575X_TUNER_H */ diff --git a/include/media/ths7303.h b/include/media/ths7303.h index 980ec51d574..a7b49297da8 100644 --- a/include/media/ths7303.h +++ b/include/media/ths7303.h @@ -30,13 +30,11 @@ * @ch_1: Bias value for channel one. * @ch_2: Bias value for channel two. * @ch_3: Bias value for channel three. - * @init_enable: initalize on init. */ struct ths7303_platform_data { u8 ch_1; u8 ch_2; u8 ch_3; - u8 init_enable; }; #endif diff --git a/include/media/tveeprom.h b/include/media/tveeprom.h index a8ad75a9152..f7119ee3977 100644 --- a/include/media/tveeprom.h +++ b/include/media/tveeprom.h @@ -1,6 +1,19 @@ /* */ +enum tveeprom_audio_processor { + /* No audio processor present */ + TVEEPROM_AUDPROC_NONE, + /* The audio processor is internal to the video processor */ + TVEEPROM_AUDPROC_INTERNAL, + /* The audio processor is a MSPXXXX device */ + TVEEPROM_AUDPROC_MSP, + /* The audio processor is another device */ + TVEEPROM_AUDPROC_OTHER, +}; + +#include <linux/if_ether.h> + struct tveeprom { u32 has_radio; /* If has_ir == 0, then it is unknown what the IR capabilities are, @@ -29,7 +42,7 @@ struct tveeprom { u32 revision; u32 serial_number; char rev_str[5]; - u8 MAC_address[6]; + u8 MAC_address[ETH_ALEN]; }; void tveeprom_hauppauge_analog(struct i2c_client *c, struct tveeprom *tvee, diff --git a/include/media/tvp7002.h b/include/media/tvp7002.h index ee4353459ef..fadb6afe9ef 100644 --- a/include/media/tvp7002.h +++ b/include/media/tvp7002.h @@ -26,31 +26,29 @@ #ifndef _TVP7002_H_ #define _TVP7002_H_ -/* Platform-dependent data - * - * clk_polarity: - * 0 -> data clocked out on rising edge of DATACLK signal - * 1 -> data clocked out on falling edge of DATACLK signal - * hs_polarity: - * 0 -> active low HSYNC output - * 1 -> active high HSYNC output - * sog_polarity: - * 0 -> normal operation - * 1 -> operation with polarity inverted - * vs_polarity: - * 0 -> active low VSYNC output - * 1 -> active high VSYNC output - * fid_polarity: - * 0 -> the field ID output is set to logic 1 for an odd - * field (field 1) and set to logic 0 for an even - * field (field 0). - * 1 -> operation with polarity inverted. +#define TVP7002_MODULE_NAME "tvp7002" + +/** + * struct tvp7002_config - Platform dependent data + *@clk_polarity: Clock polarity + * 0 - Data clocked out on rising edge of DATACLK signal + * 1 - Data clocked out on falling edge of DATACLK signal + *@hs_polarity: HSYNC polarity + * 0 - Active low HSYNC output, 1 - Active high HSYNC output + *@vs_polarity: VSYNC Polarity + * 0 - Active low VSYNC output, 1 - Active high VSYNC output + *@fid_polarity: Active-high Field ID polarity. + * 0 - The field ID output is set to logic 1 for an odd field + * (field 1) and set to logic 0 for an even field (field 0). + * 1 - Operation with polarity inverted. + *@sog_polarity: Active high Sync on Green output polarity. + * 0 - Normal operation, 1 - Operation with polarity inverted */ struct tvp7002_config { - u8 clk_polarity; - u8 hs_polarity; - u8 vs_polarity; - u8 fid_polarity; - u8 sog_polarity; + bool clk_polarity; + bool hs_polarity; + bool vs_polarity; + bool fid_polarity; + bool sog_polarity; }; #endif diff --git a/include/media/v4l2-async.h b/include/media/v4l2-async.h new file mode 100644 index 00000000000..768356917be --- /dev/null +++ b/include/media/v4l2-async.h @@ -0,0 +1,97 @@ +/* + * V4L2 asynchronous subdevice registration API + * + * Copyright (C) 2012-2013, Guennadi Liakhovetski <g.liakhovetski@gmx.de> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef V4L2_ASYNC_H +#define V4L2_ASYNC_H + +#include <linux/list.h> +#include <linux/mutex.h> + +struct device; +struct device_node; +struct v4l2_device; +struct v4l2_subdev; +struct v4l2_async_notifier; + +/* A random max subdevice number, used to allocate an array on stack */ +#define V4L2_MAX_SUBDEVS 128U + +enum v4l2_async_match_type { + V4L2_ASYNC_MATCH_CUSTOM, + V4L2_ASYNC_MATCH_DEVNAME, + V4L2_ASYNC_MATCH_I2C, + V4L2_ASYNC_MATCH_OF, +}; + +/** + * struct v4l2_async_subdev - sub-device descriptor, as known to a bridge + * @bus_type: subdevice bus type to select the appropriate matching method + * @match: union of per-bus type matching data sets + * @list: used to link struct v4l2_async_subdev objects, waiting to be + * probed, to a notifier->waiting list + */ +struct v4l2_async_subdev { + enum v4l2_async_match_type match_type; + union { + struct { + const struct device_node *node; + } of; + struct { + const char *name; + } device_name; + struct { + int adapter_id; + unsigned short address; + } i2c; + struct { + bool (*match)(struct device *, + struct v4l2_async_subdev *); + void *priv; + } custom; + } match; + + /* v4l2-async core private: not to be used by drivers */ + struct list_head list; +}; + +/** + * v4l2_async_notifier - v4l2_device notifier data + * @num_subdevs:number of subdevices + * @subdevs: array of pointers to subdevice descriptors + * @v4l2_dev: pointer to struct v4l2_device + * @waiting: list of struct v4l2_async_subdev, waiting for their drivers + * @done: list of struct v4l2_subdev, already probed + * @list: member in a global list of notifiers + * @bound: a subdevice driver has successfully probed one of subdevices + * @complete: all subdevices have been probed successfully + * @unbind: a subdevice is leaving + */ +struct v4l2_async_notifier { + unsigned int num_subdevs; + struct v4l2_async_subdev **subdevs; + struct v4l2_device *v4l2_dev; + struct list_head waiting; + struct list_head done; + struct list_head list; + int (*bound)(struct v4l2_async_notifier *notifier, + struct v4l2_subdev *subdev, + struct v4l2_async_subdev *asd); + int (*complete)(struct v4l2_async_notifier *notifier); + void (*unbind)(struct v4l2_async_notifier *notifier, + struct v4l2_subdev *subdev, + struct v4l2_async_subdev *asd); +}; + +int v4l2_async_notifier_register(struct v4l2_device *v4l2_dev, + struct v4l2_async_notifier *notifier); +void v4l2_async_notifier_unregister(struct v4l2_async_notifier *notifier); +int v4l2_async_register_subdev(struct v4l2_subdev *sd); +void v4l2_async_unregister_subdev(struct v4l2_subdev *sd); +#endif diff --git a/include/media/v4l2-chip-ident.h b/include/media/v4l2-chip-ident.h deleted file mode 100644 index c259b36bf1e..00000000000 --- a/include/media/v4l2-chip-ident.h +++ /dev/null @@ -1,352 +0,0 @@ -/* - v4l2 chip identifiers header - - This header provides a list of chip identifiers that can be returned - through the VIDIOC_DBG_G_CHIP_IDENT ioctl. - - Copyright (C) 2007 Hans Verkuil <hverkuil@xs4all.nl> - - This program is free software; you can redistribute it and/or modify - it under the terms of the GNU General Public License as published by - the Free Software Foundation; either version 2 of the License, or - (at your option) any later version. - - This program is distributed in the hope that it will be useful, - but WITHOUT ANY WARRANTY; without even the implied warranty of - MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#ifndef V4L2_CHIP_IDENT_H_ -#define V4L2_CHIP_IDENT_H_ - -/* VIDIOC_DBG_G_CHIP_IDENT: identifies the actual chip installed on the board */ - -/* KEEP THIS LIST ORDERED BY ID! - Otherwise it will be hard to see which ranges are already in use when - adding support to a new chip family. */ -enum { - /* general idents: reserved range 0-49 */ - V4L2_IDENT_NONE = 0, /* No chip matched */ - V4L2_IDENT_AMBIGUOUS = 1, /* Match too general, multiple chips matched */ - V4L2_IDENT_UNKNOWN = 2, /* Chip found, but cannot identify */ - - /* module tvaudio: reserved range 50-99 */ - V4L2_IDENT_TVAUDIO = 50, /* A tvaudio chip, unknown which it is exactly */ - - /* Sony IMX074 */ - V4L2_IDENT_IMX074 = 74, - - /* module saa7110: just ident 100 */ - V4L2_IDENT_SAA7110 = 100, - - /* module saa7115: reserved range 101-149 */ - V4L2_IDENT_SAA7111 = 101, - V4L2_IDENT_SAA7111A = 102, - V4L2_IDENT_SAA7113 = 103, - V4L2_IDENT_SAA7114 = 104, - V4L2_IDENT_SAA7115 = 105, - V4L2_IDENT_SAA7118 = 108, - - /* module saa7127: reserved range 150-199 */ - V4L2_IDENT_SAA7127 = 157, - V4L2_IDENT_SAA7129 = 159, - - /* module cx25840: reserved range 200-249 */ - V4L2_IDENT_CX25836 = 236, - V4L2_IDENT_CX25837 = 237, - V4L2_IDENT_CX25840 = 240, - V4L2_IDENT_CX25841 = 241, - V4L2_IDENT_CX25842 = 242, - V4L2_IDENT_CX25843 = 243, - - /* OmniVision sensors: reserved range 250-299 */ - V4L2_IDENT_OV7670 = 250, - V4L2_IDENT_OV7720 = 251, - V4L2_IDENT_OV7725 = 252, - V4L2_IDENT_OV7660 = 253, - V4L2_IDENT_OV9650 = 254, - V4L2_IDENT_OV9655 = 255, - V4L2_IDENT_SOI968 = 256, - V4L2_IDENT_OV9640 = 257, - V4L2_IDENT_OV6650 = 258, - V4L2_IDENT_OV2640 = 259, - V4L2_IDENT_OV9740 = 260, - V4L2_IDENT_OV5642 = 261, - - /* module saa7146: reserved range 300-309 */ - V4L2_IDENT_SAA7146 = 300, - - /* Conexant MPEG encoder/decoders: reserved range 400-420 */ - V4L2_IDENT_CX23418_843 = 403, /* Integrated A/V Decoder on the '418 */ - V4L2_IDENT_CX23415 = 415, - V4L2_IDENT_CX23416 = 416, - V4L2_IDENT_CX23417 = 417, - V4L2_IDENT_CX23418 = 418, - - /* module bt819: reserved range 810-819 */ - V4L2_IDENT_BT815A = 815, - V4L2_IDENT_BT817A = 817, - V4L2_IDENT_BT819A = 819, - - /* module au0828 */ - V4L2_IDENT_AU0828 = 828, - - /* module bttv: ident 848 + 849 */ - V4L2_IDENT_BT848 = 848, - V4L2_IDENT_BT849 = 849, - - /* module bt856: just ident 856 */ - V4L2_IDENT_BT856 = 856, - - /* module bt866: just ident 866 */ - V4L2_IDENT_BT866 = 866, - - /* module bttv: ident 878 + 879 */ - V4L2_IDENT_BT878 = 878, - V4L2_IDENT_BT879 = 879, - - /* module ks0127: reserved range 1120-1129 */ - V4L2_IDENT_KS0122S = 1122, - V4L2_IDENT_KS0127 = 1127, - V4L2_IDENT_KS0127B = 1128, - - /* module indycam: just ident 2000 */ - V4L2_IDENT_INDYCAM = 2000, - - /* module vp27smpx: just ident 2700 */ - V4L2_IDENT_VP27SMPX = 2700, - - /* module vpx3220: reserved range: 3210-3229 */ - V4L2_IDENT_VPX3214C = 3214, - V4L2_IDENT_VPX3216B = 3216, - V4L2_IDENT_VPX3220A = 3220, - - /* VX855 just ident 3409 */ - /* Other via devs could use 3314, 3324, 3327, 3336, 3364, 3353 */ - V4L2_IDENT_VIA_VX855 = 3409, - - /* module tvp5150 */ - V4L2_IDENT_TVP5150 = 5150, - - /* module saa5246a: just ident 5246 */ - V4L2_IDENT_SAA5246A = 5246, - - /* module saa5249: just ident 5249 */ - V4L2_IDENT_SAA5249 = 5249, - - /* module cs5345: just ident 5345 */ - V4L2_IDENT_CS5345 = 5345, - - /* module tea6415c: just ident 6415 */ - V4L2_IDENT_TEA6415C = 6415, - - /* module tea6420: just ident 6420 */ - V4L2_IDENT_TEA6420 = 6420, - - /* module saa6588: just ident 6588 */ - V4L2_IDENT_SAA6588 = 6588, - - /* module vs6624: just ident 6624 */ - V4L2_IDENT_VS6624 = 6624, - - /* module saa6752hs: reserved range 6750-6759 */ - V4L2_IDENT_SAA6752HS = 6752, - V4L2_IDENT_SAA6752HS_AC3 = 6753, - - /* modules tef6862: just ident 6862 */ - V4L2_IDENT_TEF6862 = 6862, - - /* module tvp7002: just ident 7002 */ - V4L2_IDENT_TVP7002 = 7002, - - /* module adv7170: just ident 7170 */ - V4L2_IDENT_ADV7170 = 7170, - - /* module adv7175: just ident 7175 */ - V4L2_IDENT_ADV7175 = 7175, - - /* module adv7180: just ident 7180 */ - V4L2_IDENT_ADV7180 = 7180, - - /* module adv7183: just ident 7183 */ - V4L2_IDENT_ADV7183 = 7183, - - /* module saa7185: just ident 7185 */ - V4L2_IDENT_SAA7185 = 7185, - - /* module saa7191: just ident 7191 */ - V4L2_IDENT_SAA7191 = 7191, - - /* module ths7303: just ident 7303 */ - V4L2_IDENT_THS7303 = 7303, - - /* module adv7343: just ident 7343 */ - V4L2_IDENT_ADV7343 = 7343, - - /* module ths7353: just ident 7353 */ - V4L2_IDENT_THS7353 = 7353, - - /* module adv7393: just ident 7393 */ - V4L2_IDENT_ADV7393 = 7393, - - /* module adv7604: just ident 7604 */ - V4L2_IDENT_ADV7604 = 7604, - - /* module saa7706h: just ident 7706 */ - V4L2_IDENT_SAA7706H = 7706, - - /* module mt9v011, just ident 8243 */ - V4L2_IDENT_MT9V011 = 8243, - - /* module wm8739: just ident 8739 */ - V4L2_IDENT_WM8739 = 8739, - - /* module wm8775: just ident 8775 */ - V4L2_IDENT_WM8775 = 8775, - - /* Marvell controllers starting at 8801 */ - V4L2_IDENT_CAFE = 8801, - V4L2_IDENT_ARMADA610 = 8802, - - /* AKM AK8813/AK8814 */ - V4L2_IDENT_AK8813 = 8813, - V4L2_IDENT_AK8814 = 8814, - - /* module cx23885 and cx25840 */ - V4L2_IDENT_CX23885 = 8850, - V4L2_IDENT_CX23885_AV = 8851, /* Integrated A/V decoder */ - V4L2_IDENT_CX23887 = 8870, - V4L2_IDENT_CX23887_AV = 8871, /* Integrated A/V decoder */ - V4L2_IDENT_CX23888 = 8880, - V4L2_IDENT_CX23888_AV = 8881, /* Integrated A/V decoder */ - V4L2_IDENT_CX23888_IR = 8882, /* Integrated infrared controller */ - - /* module ad9389b: just ident 9389 */ - V4L2_IDENT_AD9389B = 9389, - - /* module tda9840: just ident 9840 */ - V4L2_IDENT_TDA9840 = 9840, - - /* module tw9910: just ident 9910 */ - V4L2_IDENT_TW9910 = 9910, - - /* module sn9c20x: just ident 10000 */ - V4L2_IDENT_SN9C20X = 10000, - - /* module cx231xx and cx25840 */ - V4L2_IDENT_CX2310X_AV = 23099, /* Integrated A/V decoder; not in '100 */ - V4L2_IDENT_CX23100 = 23100, - V4L2_IDENT_CX23101 = 23101, - V4L2_IDENT_CX23102 = 23102, - - /* module msp3400: reserved range 34000-34999 for msp34xx */ - V4L2_IDENT_MSPX4XX = 34000, /* generic MSPX4XX identifier, only - use internally (tveeprom.c). */ - - V4L2_IDENT_MSP3400B = 34002, - V4L2_IDENT_MSP3400C = 34003, - V4L2_IDENT_MSP3400D = 34004, - V4L2_IDENT_MSP3400G = 34007, - V4L2_IDENT_MSP3401G = 34017, - V4L2_IDENT_MSP3402G = 34027, - V4L2_IDENT_MSP3405D = 34054, - V4L2_IDENT_MSP3405G = 34057, - V4L2_IDENT_MSP3407D = 34074, - V4L2_IDENT_MSP3407G = 34077, - - V4L2_IDENT_MSP3410B = 34102, - V4L2_IDENT_MSP3410C = 34103, - V4L2_IDENT_MSP3410D = 34104, - V4L2_IDENT_MSP3410G = 34107, - V4L2_IDENT_MSP3411G = 34117, - V4L2_IDENT_MSP3412G = 34127, - V4L2_IDENT_MSP3415D = 34154, - V4L2_IDENT_MSP3415G = 34157, - V4L2_IDENT_MSP3417D = 34174, - V4L2_IDENT_MSP3417G = 34177, - - V4L2_IDENT_MSP3420G = 34207, - V4L2_IDENT_MSP3421G = 34217, - V4L2_IDENT_MSP3422G = 34227, - V4L2_IDENT_MSP3425G = 34257, - V4L2_IDENT_MSP3427G = 34277, - - V4L2_IDENT_MSP3430G = 34307, - V4L2_IDENT_MSP3431G = 34317, - V4L2_IDENT_MSP3435G = 34357, - V4L2_IDENT_MSP3437G = 34377, - - V4L2_IDENT_MSP3440G = 34407, - V4L2_IDENT_MSP3441G = 34417, - V4L2_IDENT_MSP3442G = 34427, - V4L2_IDENT_MSP3445G = 34457, - V4L2_IDENT_MSP3447G = 34477, - - V4L2_IDENT_MSP3450G = 34507, - V4L2_IDENT_MSP3451G = 34517, - V4L2_IDENT_MSP3452G = 34527, - V4L2_IDENT_MSP3455G = 34557, - V4L2_IDENT_MSP3457G = 34577, - - V4L2_IDENT_MSP3460G = 34607, - V4L2_IDENT_MSP3461G = 34617, - V4L2_IDENT_MSP3465G = 34657, - V4L2_IDENT_MSP3467G = 34677, - - /* module msp3400: reserved range 44000-44999 for msp44xx */ - V4L2_IDENT_MSP4400G = 44007, - V4L2_IDENT_MSP4408G = 44087, - V4L2_IDENT_MSP4410G = 44107, - V4L2_IDENT_MSP4418G = 44187, - V4L2_IDENT_MSP4420G = 44207, - V4L2_IDENT_MSP4428G = 44287, - V4L2_IDENT_MSP4440G = 44407, - V4L2_IDENT_MSP4448G = 44487, - V4L2_IDENT_MSP4450G = 44507, - V4L2_IDENT_MSP4458G = 44587, - - /* Micron CMOS sensor chips: 45000-45099 */ - V4L2_IDENT_MT9M001C12ST = 45000, - V4L2_IDENT_MT9M001C12STM = 45005, - V4L2_IDENT_MT9M111 = 45007, - V4L2_IDENT_MT9M112 = 45008, - V4L2_IDENT_MT9V022IX7ATC = 45010, /* No way to detect "normal" I77ATx */ - V4L2_IDENT_MT9V022IX7ATM = 45015, /* and "lead free" IA7ATx chips */ - V4L2_IDENT_MT9T031 = 45020, - V4L2_IDENT_MT9T111 = 45021, - V4L2_IDENT_MT9T112 = 45022, - V4L2_IDENT_MT9V111 = 45031, - V4L2_IDENT_MT9V112 = 45032, - - /* HV7131R CMOS sensor: just ident 46000 */ - V4L2_IDENT_HV7131R = 46000, - - /* Sharp RJ54N1CB0C, 0xCB0C = 51980 */ - V4L2_IDENT_RJ54N1CB0C = 51980, - - /* module m52790: just ident 52790 */ - V4L2_IDENT_M52790 = 52790, - - /* module cs53132a: just ident 53132 */ - V4L2_IDENT_CS53l32A = 53132, - - /* modules upd61151 MPEG2 encoder: just ident 54000 */ - V4L2_IDENT_UPD61161 = 54000, - /* modules upd61152 MPEG2 encoder with AC3: just ident 54001 */ - V4L2_IDENT_UPD61162 = 54001, - - /* module upd64031a: just ident 64031 */ - V4L2_IDENT_UPD64031A = 64031, - - /* module upd64083: just ident 64083 */ - V4L2_IDENT_UPD64083 = 64083, - - /* Don't just add new IDs at the end: KEEP THIS LIST ORDERED BY ID! */ -}; - -#endif diff --git a/include/media/v4l2-clk.h b/include/media/v4l2-clk.h new file mode 100644 index 00000000000..0b36cc13830 --- /dev/null +++ b/include/media/v4l2-clk.h @@ -0,0 +1,71 @@ +/* + * V4L2 clock service + * + * Copyright (C) 2012-2013, Guennadi Liakhovetski <g.liakhovetski@gmx.de> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * ATTENTION: This is a temporary API and it shall be replaced by the generic + * clock API, when the latter becomes widely available. + */ + +#ifndef MEDIA_V4L2_CLK_H +#define MEDIA_V4L2_CLK_H + +#include <linux/atomic.h> +#include <linux/export.h> +#include <linux/list.h> +#include <linux/mutex.h> + +struct module; +struct device; + +struct v4l2_clk { + struct list_head list; + const struct v4l2_clk_ops *ops; + const char *dev_id; + const char *id; + int enable; + struct mutex lock; /* Protect the enable count */ + atomic_t use_count; + void *priv; +}; + +struct v4l2_clk_ops { + struct module *owner; + int (*enable)(struct v4l2_clk *clk); + void (*disable)(struct v4l2_clk *clk); + unsigned long (*get_rate)(struct v4l2_clk *clk); + int (*set_rate)(struct v4l2_clk *clk, unsigned long); +}; + +struct v4l2_clk *v4l2_clk_register(const struct v4l2_clk_ops *ops, + const char *dev_name, + const char *name, void *priv); +void v4l2_clk_unregister(struct v4l2_clk *clk); +struct v4l2_clk *v4l2_clk_get(struct device *dev, const char *id); +void v4l2_clk_put(struct v4l2_clk *clk); +int v4l2_clk_enable(struct v4l2_clk *clk); +void v4l2_clk_disable(struct v4l2_clk *clk); +unsigned long v4l2_clk_get_rate(struct v4l2_clk *clk); +int v4l2_clk_set_rate(struct v4l2_clk *clk, unsigned long rate); + +struct module; + +struct v4l2_clk *__v4l2_clk_register_fixed(const char *dev_id, + const char *id, unsigned long rate, struct module *owner); +void v4l2_clk_unregister_fixed(struct v4l2_clk *clk); + +static inline struct v4l2_clk *v4l2_clk_register_fixed(const char *dev_id, + const char *id, + unsigned long rate) +{ + return __v4l2_clk_register_fixed(dev_id, id, rate, THIS_MODULE); +} + +#define v4l2_clk_name_i2c(name, size, adap, client) snprintf(name, size, \ + "%d-%04x", adap, client) + +#endif diff --git a/include/media/v4l2-common.h b/include/media/v4l2-common.h index 1d93c48cb37..48f974866f1 100644 --- a/include/media/v4l2-common.h +++ b/include/media/v4l2-common.h @@ -35,7 +35,7 @@ printk(level "%s %d-%04x: " fmt, name, i2c_adapter_id(adapter), addr , ## arg) #define v4l_client_printk(level, client, fmt, arg...) \ - v4l_printk(level, (client)->driver->driver.name, (client)->adapter, \ + v4l_printk(level, (client)->dev.driver->name, (client)->adapter, \ (client)->addr, fmt , ## arg) #define v4l_err(client, fmt, arg...) \ @@ -86,6 +86,7 @@ int v4l2_ctrl_check(struct v4l2_ext_control *ctrl, struct v4l2_queryctrl *qctrl, const char * const *menu_items); const char *v4l2_ctrl_get_name(u32 id); const char * const *v4l2_ctrl_get_menu(u32 id); +const s64 *v4l2_ctrl_get_int_menu(u32 id, u32 *len); int v4l2_ctrl_query_fill(struct v4l2_queryctrl *qctrl, s32 min, s32 max, s32 step, s32 def); int v4l2_ctrl_query_menu(struct v4l2_querymenu *qmenu, struct v4l2_queryctrl *qctrl, const char * const *menu_items); @@ -100,16 +101,6 @@ u32 v4l2_ctrl_next(const u32 * const *ctrl_classes, u32 id); /* ------------------------------------------------------------------------- */ -/* Register/chip ident helper function */ - -struct i2c_client; /* forward reference */ -int v4l2_chip_match_i2c_client(struct i2c_client *c, const struct v4l2_dbg_match *match); -int v4l2_chip_ident_i2c_client(struct i2c_client *c, struct v4l2_dbg_chip_ident *chip, - u32 ident, u32 revision); -int v4l2_chip_match_host(const struct v4l2_dbg_match *match); - -/* ------------------------------------------------------------------------- */ - /* I2C Helper functions */ struct i2c_driver; @@ -211,19 +202,6 @@ const struct v4l2_frmsize_discrete *v4l2_find_nearest_format( const struct v4l2_discrete_probe *probe, s32 width, s32 height); -bool v4l_match_dv_timings(const struct v4l2_dv_timings *t1, - const struct v4l2_dv_timings *t2, - unsigned pclock_delta); - -bool v4l2_detect_cvt(unsigned frame_height, unsigned hfreq, unsigned vsync, - u32 polarities, struct v4l2_dv_timings *fmt); - -bool v4l2_detect_gtf(unsigned frame_height, unsigned hfreq, unsigned vsync, - u32 polarities, struct v4l2_fract aspect, - struct v4l2_dv_timings *fmt); - -struct v4l2_fract v4l2_calc_aspect_ratio(u8 hor_landscape, u8 vert_portrait); - void v4l2_get_timestamp(struct timeval *tv); #endif /* V4L2_COMMON_H_ */ diff --git a/include/media/v4l2-ctrls.h b/include/media/v4l2-ctrls.h index 7343a27fe81..16f7f260651 100644 --- a/include/media/v4l2-ctrls.h +++ b/include/media/v4l2-ctrls.h @@ -22,6 +22,7 @@ #define _V4L2_CTRLS_H #include <linux/list.h> +#include <linux/mutex.h> #include <linux/videodev2.h> /* forward references */ @@ -570,7 +571,7 @@ static inline void v4l2_ctrl_lock(struct v4l2_ctrl *ctrl) mutex_lock(ctrl->handler->lock); } -/** v4l2_ctrl_lock() - Helper function to unlock the handler +/** v4l2_ctrl_unlock() - Helper function to unlock the handler * associated with the control. * @ctrl: The control to unlock. */ diff --git a/include/media/v4l2-dev.h b/include/media/v4l2-dev.h index 95d1c91770f..eec6e460f64 100644 --- a/include/media/v4l2-dev.h +++ b/include/media/v4l2-dev.h @@ -24,7 +24,8 @@ #define VFL_TYPE_VBI 1 #define VFL_TYPE_RADIO 2 #define VFL_TYPE_SUBDEV 3 -#define VFL_TYPE_MAX 4 +#define VFL_TYPE_SDR 4 +#define VFL_TYPE_MAX 5 /* Is this a receiver, transmitter or mem-to-mem? */ /* Ignored for VFL_TYPE_SUBDEV. */ @@ -96,9 +97,9 @@ struct video_device struct device dev; /* v4l device */ struct cdev *cdev; /* character device */ - /* Set either parent or v4l2_dev if your driver uses v4l2_device */ - struct device *parent; /* device parent */ struct v4l2_device *v4l2_dev; /* v4l2_device parent */ + /* Only set parent if that can't be deduced from v4l2_dev */ + struct device *dev_parent; /* device parent */ /* Control handler associated with this device node. May be NULL. */ struct v4l2_ctrl_handler *ctrl_handler; @@ -129,7 +130,6 @@ struct video_device /* Video standard vars */ v4l2_std_id tvnorms; /* Supported tv norms */ - v4l2_std_id current_norm; /* Current tvnorm */ /* callbacks */ void (*release)(struct video_device *vdev); diff --git a/include/media/v4l2-device.h b/include/media/v4l2-device.h index c9b1593923f..ffb69da3ce9 100644 --- a/include/media/v4l2-device.h +++ b/include/media/v4l2-device.h @@ -120,6 +120,14 @@ void v4l2_device_unregister_subdev(struct v4l2_subdev *sd); int __must_check v4l2_device_register_subdev_nodes(struct v4l2_device *v4l2_dev); +/* Send a notification to v4l2_device. */ +static inline void v4l2_subdev_notify(struct v4l2_subdev *sd, + unsigned int notification, void *arg) +{ + if (sd && sd->v4l2_dev && sd->v4l2_dev->notify) + sd->v4l2_dev->notify(sd, notification, arg); +} + /* Iterate over all subdevs. */ #define v4l2_device_for_each_subdev(sd, v4l2_dev) \ list_for_each_entry(sd, &(v4l2_dev)->subdevs, list) diff --git a/include/media/v4l2-dv-timings.h b/include/media/v4l2-dv-timings.h new file mode 100644 index 00000000000..4becc671639 --- /dev/null +++ b/include/media/v4l2-dv-timings.h @@ -0,0 +1,161 @@ +/* + * v4l2-dv-timings - Internal header with dv-timings helper functions + * + * Copyright 2013 Cisco Systems, Inc. and/or its affiliates. All rights reserved. + * + * This program is free software; you may redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; version 2 of the License. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF + * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS + * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN + * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN + * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE + * SOFTWARE. + * + */ + +#ifndef __V4L2_DV_TIMINGS_H +#define __V4L2_DV_TIMINGS_H + +#include <linux/videodev2.h> + +/** v4l2_dv_timings_presets: list of all dv_timings presets. + */ +extern const struct v4l2_dv_timings v4l2_dv_timings_presets[]; + +/** v4l2_check_dv_timings_fnc - timings check callback + * @t: the v4l2_dv_timings struct. + * @handle: a handle from the driver. + * + * Returns true if the given timings are valid. + */ +typedef bool v4l2_check_dv_timings_fnc(const struct v4l2_dv_timings *t, void *handle); + +/** v4l2_valid_dv_timings() - are these timings valid? + * @t: the v4l2_dv_timings struct. + * @cap: the v4l2_dv_timings_cap capabilities. + * @fnc: callback to check if this timing is OK. May be NULL. + * @fnc_handle: a handle that is passed on to @fnc. + * + * Returns true if the given dv_timings struct is supported by the + * hardware capabilities and the callback function (if non-NULL), returns + * false otherwise. + */ +bool v4l2_valid_dv_timings(const struct v4l2_dv_timings *t, + const struct v4l2_dv_timings_cap *cap, + v4l2_check_dv_timings_fnc fnc, + void *fnc_handle); + +/** v4l2_enum_dv_timings_cap() - Helper function to enumerate possible DV timings based on capabilities + * @t: the v4l2_enum_dv_timings struct. + * @cap: the v4l2_dv_timings_cap capabilities. + * @fnc: callback to check if this timing is OK. May be NULL. + * @fnc_handle: a handle that is passed on to @fnc. + * + * This enumerates dv_timings using the full list of possible CEA-861 and DMT + * timings, filtering out any timings that are not supported based on the + * hardware capabilities and the callback function (if non-NULL). + * + * If a valid timing for the given index is found, it will fill in @t and + * return 0, otherwise it returns -EINVAL. + */ +int v4l2_enum_dv_timings_cap(struct v4l2_enum_dv_timings *t, + const struct v4l2_dv_timings_cap *cap, + v4l2_check_dv_timings_fnc fnc, + void *fnc_handle); + +/** v4l2_find_dv_timings_cap() - Find the closest timings struct + * @t: the v4l2_enum_dv_timings struct. + * @cap: the v4l2_dv_timings_cap capabilities. + * @pclock_delta: maximum delta between t->pixelclock and the timing struct + * under consideration. + * @fnc: callback to check if a given timings struct is OK. May be NULL. + * @fnc_handle: a handle that is passed on to @fnc. + * + * This function tries to map the given timings to an entry in the + * full list of possible CEA-861 and DMT timings, filtering out any timings + * that are not supported based on the hardware capabilities and the callback + * function (if non-NULL). + * + * On success it will fill in @t with the found timings and it returns true. + * On failure it will return false. + */ +bool v4l2_find_dv_timings_cap(struct v4l2_dv_timings *t, + const struct v4l2_dv_timings_cap *cap, + unsigned pclock_delta, + v4l2_check_dv_timings_fnc fnc, + void *fnc_handle); + +/** v4l2_match_dv_timings() - do two timings match? + * @measured: the measured timings data. + * @standard: the timings according to the standard. + * @pclock_delta: maximum delta in Hz between standard->pixelclock and + * the measured timings. + * + * Returns true if the two timings match, returns false otherwise. + */ +bool v4l2_match_dv_timings(const struct v4l2_dv_timings *measured, + const struct v4l2_dv_timings *standard, + unsigned pclock_delta); + +/** v4l2_print_dv_timings() - log the contents of a dv_timings struct + * @dev_prefix:device prefix for each log line. + * @prefix: additional prefix for each log line, may be NULL. + * @t: the timings data. + * @detailed: if true, give a detailed log. + */ +void v4l2_print_dv_timings(const char *dev_prefix, const char *prefix, + const struct v4l2_dv_timings *t, bool detailed); + +/** v4l2_detect_cvt - detect if the given timings follow the CVT standard + * @frame_height - the total height of the frame (including blanking) in lines. + * @hfreq - the horizontal frequency in Hz. + * @vsync - the height of the vertical sync in lines. + * @polarities - the horizontal and vertical polarities (same as struct + * v4l2_bt_timings polarities). + * @fmt - the resulting timings. + * + * This function will attempt to detect if the given values correspond to a + * valid CVT format. If so, then it will return true, and fmt will be filled + * in with the found CVT timings. + */ +bool v4l2_detect_cvt(unsigned frame_height, unsigned hfreq, unsigned vsync, + u32 polarities, struct v4l2_dv_timings *fmt); + +/** v4l2_detect_gtf - detect if the given timings follow the GTF standard + * @frame_height - the total height of the frame (including blanking) in lines. + * @hfreq - the horizontal frequency in Hz. + * @vsync - the height of the vertical sync in lines. + * @polarities - the horizontal and vertical polarities (same as struct + * v4l2_bt_timings polarities). + * @aspect - preferred aspect ratio. GTF has no method of determining the + * aspect ratio in order to derive the image width from the + * image height, so it has to be passed explicitly. Usually + * the native screen aspect ratio is used for this. If it + * is not filled in correctly, then 16:9 will be assumed. + * @fmt - the resulting timings. + * + * This function will attempt to detect if the given values correspond to a + * valid GTF format. If so, then it will return true, and fmt will be filled + * in with the found GTF timings. + */ +bool v4l2_detect_gtf(unsigned frame_height, unsigned hfreq, unsigned vsync, + u32 polarities, struct v4l2_fract aspect, + struct v4l2_dv_timings *fmt); + +/** v4l2_calc_aspect_ratio - calculate the aspect ratio based on bytes + * 0x15 and 0x16 from the EDID. + * @hor_landscape - byte 0x15 from the EDID. + * @vert_portrait - byte 0x16 from the EDID. + * + * Determines the aspect ratio from the EDID. + * See VESA Enhanced EDID standard, release A, rev 2, section 3.6.2: + * "Horizontal and Vertical Screen Size or Aspect Ratio" + */ +struct v4l2_fract v4l2_calc_aspect_ratio(u8 hor_landscape, u8 vert_portrait); + +#endif diff --git a/include/media/v4l2-event.h b/include/media/v4l2-event.h index be05d019de2..1ab9045e52e 100644 --- a/include/media/v4l2-event.h +++ b/include/media/v4l2-event.h @@ -132,4 +132,8 @@ int v4l2_event_unsubscribe(struct v4l2_fh *fh, void v4l2_event_unsubscribe_all(struct v4l2_fh *fh); int v4l2_event_subdev_unsubscribe(struct v4l2_subdev *sd, struct v4l2_fh *fh, struct v4l2_event_subscription *sub); +int v4l2_src_change_event_subscribe(struct v4l2_fh *fh, + const struct v4l2_event_subscription *sub); +int v4l2_src_change_event_subdev_subscribe(struct v4l2_subdev *sd, + struct v4l2_fh *fh, struct v4l2_event_subscription *sub); #endif /* V4L2_EVENT_H */ diff --git a/include/media/v4l2-fh.h b/include/media/v4l2-fh.h index a62ee18cb7b..80351677516 100644 --- a/include/media/v4l2-fh.h +++ b/include/media/v4l2-fh.h @@ -26,7 +26,9 @@ #ifndef V4L2_FH_H #define V4L2_FH_H +#include <linux/fs.h> #include <linux/list.h> +#include <linux/videodev2.h> struct video_device; struct v4l2_ctrl_handler; @@ -43,6 +45,10 @@ struct v4l2_fh { struct list_head available; /* Dequeueable event */ unsigned int navailable; u32 sequence; + +#if IS_ENABLED(CONFIG_V4L2_MEM2MEM_DEV) + struct v4l2_m2m_ctx *m2m_ctx; +#endif }; /* diff --git a/include/media/v4l2-int-device.h b/include/media/v4l2-int-device.h deleted file mode 100644 index e6aa2318367..00000000000 --- a/include/media/v4l2-int-device.h +++ /dev/null @@ -1,308 +0,0 @@ -/* - * include/media/v4l2-int-device.h - * - * V4L2 internal ioctl interface. - * - * Copyright (C) 2007 Nokia Corporation. - * - * Contact: Sakari Ailus <sakari.ailus@nokia.com> - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * version 2 as published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, but - * WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU - * General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA - * 02110-1301 USA - */ - -#ifndef V4L2_INT_DEVICE_H -#define V4L2_INT_DEVICE_H - -#include <media/v4l2-common.h> - -#define V4L2NAMESIZE 32 - -/* - * - * The internal V4L2 device interface core. - * - */ - -enum v4l2_int_type { - v4l2_int_type_master = 1, - v4l2_int_type_slave -}; - -struct module; - -struct v4l2_int_device; - -struct v4l2_int_master { - int (*attach)(struct v4l2_int_device *slave); - void (*detach)(struct v4l2_int_device *slave); -}; - -typedef int (v4l2_int_ioctl_func)(struct v4l2_int_device *); -typedef int (v4l2_int_ioctl_func_0)(struct v4l2_int_device *); -typedef int (v4l2_int_ioctl_func_1)(struct v4l2_int_device *, void *); - -struct v4l2_int_ioctl_desc { - int num; - v4l2_int_ioctl_func *func; -}; - -struct v4l2_int_slave { - /* Don't touch master. */ - struct v4l2_int_device *master; - - char attach_to[V4L2NAMESIZE]; - - int num_ioctls; - struct v4l2_int_ioctl_desc *ioctls; -}; - -struct v4l2_int_device { - /* Don't touch head. */ - struct list_head head; - - struct module *module; - - char name[V4L2NAMESIZE]; - - enum v4l2_int_type type; - union { - struct v4l2_int_master *master; - struct v4l2_int_slave *slave; - } u; - - void *priv; -}; - -void v4l2_int_device_try_attach_all(void); - -int v4l2_int_device_register(struct v4l2_int_device *d); -void v4l2_int_device_unregister(struct v4l2_int_device *d); - -int v4l2_int_ioctl_0(struct v4l2_int_device *d, int cmd); -int v4l2_int_ioctl_1(struct v4l2_int_device *d, int cmd, void *arg); - -/* - * - * Types and definitions for IOCTL commands. - * - */ - -enum v4l2_power { - V4L2_POWER_OFF = 0, - V4L2_POWER_ON, - V4L2_POWER_STANDBY, -}; - -/* Slave interface type. */ -enum v4l2_if_type { - /* - * Parallel 8-, 10- or 12-bit interface, used by for example - * on certain image sensors. - */ - V4L2_IF_TYPE_BT656, -}; - -enum v4l2_if_type_bt656_mode { - /* - * Modes without Bt synchronisation codes. Separate - * synchronisation signal lines are used. - */ - V4L2_IF_TYPE_BT656_MODE_NOBT_8BIT, - V4L2_IF_TYPE_BT656_MODE_NOBT_10BIT, - V4L2_IF_TYPE_BT656_MODE_NOBT_12BIT, - /* - * Use Bt synchronisation codes. The vertical and horizontal - * synchronisation is done based on synchronisation codes. - */ - V4L2_IF_TYPE_BT656_MODE_BT_8BIT, - V4L2_IF_TYPE_BT656_MODE_BT_10BIT, -}; - -struct v4l2_if_type_bt656 { - /* - * 0: Frame begins when vsync is high. - * 1: Frame begins when vsync changes from low to high. - */ - unsigned frame_start_on_rising_vs:1; - /* Use Bt synchronisation codes for sync correction. */ - unsigned bt_sync_correct:1; - /* Swap every two adjacent image data elements. */ - unsigned swap:1; - /* Inverted latch clock polarity from slave. */ - unsigned latch_clk_inv:1; - /* Hs polarity. 0 is active high, 1 active low. */ - unsigned nobt_hs_inv:1; - /* Vs polarity. 0 is active high, 1 active low. */ - unsigned nobt_vs_inv:1; - enum v4l2_if_type_bt656_mode mode; - /* Minimum accepted bus clock for slave (in Hz). */ - u32 clock_min; - /* Maximum accepted bus clock for slave. */ - u32 clock_max; - /* - * Current wish of the slave. May only change in response to - * ioctls that affect image capture. - */ - u32 clock_curr; -}; - -struct v4l2_ifparm { - enum v4l2_if_type if_type; - union { - struct v4l2_if_type_bt656 bt656; - } u; -}; - -/* IOCTL command numbers. */ -enum v4l2_int_ioctl_num { - /* - * - * "Proper" V4L ioctls, as in struct video_device. - * - */ - vidioc_int_enum_fmt_cap_num = 1, - vidioc_int_g_fmt_cap_num, - vidioc_int_s_fmt_cap_num, - vidioc_int_try_fmt_cap_num, - vidioc_int_queryctrl_num, - vidioc_int_g_ctrl_num, - vidioc_int_s_ctrl_num, - vidioc_int_cropcap_num, - vidioc_int_g_crop_num, - vidioc_int_s_crop_num, - vidioc_int_g_parm_num, - vidioc_int_s_parm_num, - vidioc_int_querystd_num, - vidioc_int_s_std_num, - vidioc_int_s_video_routing_num, - - /* - * - * Strictly internal ioctls. - * - */ - /* Initialise the device when slave attaches to the master. */ - vidioc_int_dev_init_num = 1000, - /* Delinitialise the device at slave detach. */ - vidioc_int_dev_exit_num, - /* Set device power state. */ - vidioc_int_s_power_num, - /* - * Get slave private data, e.g. platform-specific slave - * configuration used by the master. - */ - vidioc_int_g_priv_num, - /* Get slave interface parameters. */ - vidioc_int_g_ifparm_num, - /* Does the slave need to be reset after VIDIOC_DQBUF? */ - vidioc_int_g_needs_reset_num, - vidioc_int_enum_framesizes_num, - vidioc_int_enum_frameintervals_num, - - /* - * - * VIDIOC_INT_* ioctls. - * - */ - /* VIDIOC_INT_RESET */ - vidioc_int_reset_num, - /* VIDIOC_INT_INIT */ - vidioc_int_init_num, - /* VIDIOC_DBG_G_CHIP_IDENT */ - vidioc_int_g_chip_ident_num, - - /* - * - * Start of private ioctls. - * - */ - vidioc_int_priv_start_num = 2000, -}; - -/* - * - * IOCTL wrapper functions for better type checking. - * - */ - -#define V4L2_INT_WRAPPER_0(name) \ - static inline int vidioc_int_##name(struct v4l2_int_device *d) \ - { \ - return v4l2_int_ioctl_0(d, vidioc_int_##name##_num); \ - } \ - \ - static inline struct v4l2_int_ioctl_desc \ - vidioc_int_##name##_cb(int (*func) \ - (struct v4l2_int_device *)) \ - { \ - struct v4l2_int_ioctl_desc desc; \ - \ - desc.num = vidioc_int_##name##_num; \ - desc.func = (v4l2_int_ioctl_func *)func; \ - \ - return desc; \ - } - -#define V4L2_INT_WRAPPER_1(name, arg_type, asterisk) \ - static inline int vidioc_int_##name(struct v4l2_int_device *d, \ - arg_type asterisk arg) \ - { \ - return v4l2_int_ioctl_1(d, vidioc_int_##name##_num, \ - (void *)(unsigned long)arg); \ - } \ - \ - static inline struct v4l2_int_ioctl_desc \ - vidioc_int_##name##_cb(int (*func) \ - (struct v4l2_int_device *, \ - arg_type asterisk)) \ - { \ - struct v4l2_int_ioctl_desc desc; \ - \ - desc.num = vidioc_int_##name##_num; \ - desc.func = (v4l2_int_ioctl_func *)func; \ - \ - return desc; \ - } - -V4L2_INT_WRAPPER_1(enum_fmt_cap, struct v4l2_fmtdesc, *); -V4L2_INT_WRAPPER_1(g_fmt_cap, struct v4l2_format, *); -V4L2_INT_WRAPPER_1(s_fmt_cap, struct v4l2_format, *); -V4L2_INT_WRAPPER_1(try_fmt_cap, struct v4l2_format, *); -V4L2_INT_WRAPPER_1(queryctrl, struct v4l2_queryctrl, *); -V4L2_INT_WRAPPER_1(g_ctrl, struct v4l2_control, *); -V4L2_INT_WRAPPER_1(s_ctrl, struct v4l2_control, *); -V4L2_INT_WRAPPER_1(cropcap, struct v4l2_cropcap, *); -V4L2_INT_WRAPPER_1(g_crop, struct v4l2_crop, *); -V4L2_INT_WRAPPER_1(s_crop, struct v4l2_crop, *); -V4L2_INT_WRAPPER_1(g_parm, struct v4l2_streamparm, *); -V4L2_INT_WRAPPER_1(s_parm, struct v4l2_streamparm, *); -V4L2_INT_WRAPPER_1(querystd, v4l2_std_id, *); -V4L2_INT_WRAPPER_1(s_std, v4l2_std_id, *); -V4L2_INT_WRAPPER_1(s_video_routing, struct v4l2_routing, *); - -V4L2_INT_WRAPPER_0(dev_init); -V4L2_INT_WRAPPER_0(dev_exit); -V4L2_INT_WRAPPER_1(s_power, enum v4l2_power, ); -V4L2_INT_WRAPPER_1(g_priv, void, *); -V4L2_INT_WRAPPER_1(g_ifparm, struct v4l2_ifparm, *); -V4L2_INT_WRAPPER_1(g_needs_reset, void, *); -V4L2_INT_WRAPPER_1(enum_framesizes, struct v4l2_frmsizeenum, *); -V4L2_INT_WRAPPER_1(enum_frameintervals, struct v4l2_frmivalenum, *); - -V4L2_INT_WRAPPER_0(reset); -V4L2_INT_WRAPPER_0(init); -V4L2_INT_WRAPPER_1(g_chip_ident, int, *); - -#endif diff --git a/include/media/v4l2-ioctl.h b/include/media/v4l2-ioctl.h index 931652f0e2a..50cf7c110a7 100644 --- a/include/media/v4l2-ioctl.h +++ b/include/media/v4l2-ioctl.h @@ -40,6 +40,8 @@ struct v4l2_ioctl_ops { struct v4l2_fmtdesc *f); int (*vidioc_enum_fmt_vid_out_mplane)(struct file *file, void *fh, struct v4l2_fmtdesc *f); + int (*vidioc_enum_fmt_sdr_cap) (struct file *file, void *fh, + struct v4l2_fmtdesc *f); /* VIDIOC_G_FMT handlers */ int (*vidioc_g_fmt_vid_cap) (struct file *file, void *fh, @@ -62,6 +64,8 @@ struct v4l2_ioctl_ops { struct v4l2_format *f); int (*vidioc_g_fmt_vid_out_mplane)(struct file *file, void *fh, struct v4l2_format *f); + int (*vidioc_g_fmt_sdr_cap) (struct file *file, void *fh, + struct v4l2_format *f); /* VIDIOC_S_FMT handlers */ int (*vidioc_s_fmt_vid_cap) (struct file *file, void *fh, @@ -84,6 +88,8 @@ struct v4l2_ioctl_ops { struct v4l2_format *f); int (*vidioc_s_fmt_vid_out_mplane)(struct file *file, void *fh, struct v4l2_format *f); + int (*vidioc_s_fmt_sdr_cap) (struct file *file, void *fh, + struct v4l2_format *f); /* VIDIOC_TRY_FMT handlers */ int (*vidioc_try_fmt_vid_cap) (struct file *file, void *fh, @@ -106,6 +112,8 @@ struct v4l2_ioctl_ops { struct v4l2_format *f); int (*vidioc_try_fmt_vid_out_mplane)(struct file *file, void *fh, struct v4l2_format *f); + int (*vidioc_try_fmt_sdr_cap) (struct file *file, void *fh, + struct v4l2_format *f); /* Buffer handlers */ int (*vidioc_reqbufs) (struct file *file, void *fh, struct v4l2_requestbuffers *b); @@ -247,8 +255,6 @@ struct v4l2_ioctl_ops { int (*vidioc_g_chip_info) (struct file *file, void *fh, struct v4l2_dbg_chip_info *chip); #endif - int (*vidioc_g_chip_ident) (struct file *file, void *fh, - struct v4l2_dbg_chip_ident *chip); int (*vidioc_enum_framesizes) (struct file *file, void *fh, struct v4l2_frmsizeenum *fsize); @@ -267,6 +273,8 @@ struct v4l2_ioctl_ops { struct v4l2_enum_dv_timings *timings); int (*vidioc_dv_timings_cap) (struct file *file, void *fh, struct v4l2_dv_timings_cap *cap); + int (*vidioc_g_edid) (struct file *file, void *fh, struct v4l2_edid *edid); + int (*vidioc_s_edid) (struct file *file, void *fh, struct v4l2_edid *edid); int (*vidioc_subscribe_event) (struct v4l2_fh *fh, const struct v4l2_event_subscription *sub); diff --git a/include/media/v4l2-mediabus.h b/include/media/v4l2-mediabus.h index 83ae07e5335..395c4a95a42 100644 --- a/include/media/v4l2-mediabus.h +++ b/include/media/v4l2-mediabus.h @@ -40,6 +40,9 @@ #define V4L2_MBUS_FIELD_EVEN_HIGH (1 << 10) /* FIELD = 1/0 - Field1 (odd)/Field2 (even) */ #define V4L2_MBUS_FIELD_EVEN_LOW (1 << 11) +/* Active state of Sync-on-green (SoG) signal, 0/1 for LOW/HIGH respectively. */ +#define V4L2_MBUS_VIDEO_SOG_ACTIVE_HIGH (1 << 12) +#define V4L2_MBUS_VIDEO_SOG_ACTIVE_LOW (1 << 13) /* Serial flags */ /* How many lanes the client can use */ diff --git a/include/media/v4l2-mem2mem.h b/include/media/v4l2-mem2mem.h index d3eef01da64..12ea5a6a433 100644 --- a/include/media/v4l2-mem2mem.h +++ b/include/media/v4l2-mem2mem.h @@ -60,9 +60,13 @@ struct v4l2_m2m_queue_ctx { struct list_head rdy_queue; spinlock_t rdy_spinlock; u8 num_rdy; + bool buffered; }; struct v4l2_m2m_ctx { + /* optional cap/out vb2 queues lock */ + struct mutex *q_lock; + /* private: internal use only */ struct v4l2_m2m_dev *m2m_dev; @@ -110,6 +114,8 @@ int v4l2_m2m_qbuf(struct file *file, struct v4l2_m2m_ctx *m2m_ctx, struct v4l2_buffer *buf); int v4l2_m2m_dqbuf(struct file *file, struct v4l2_m2m_ctx *m2m_ctx, struct v4l2_buffer *buf); +int v4l2_m2m_create_bufs(struct file *file, struct v4l2_m2m_ctx *m2m_ctx, + struct v4l2_create_buffers *create); int v4l2_m2m_expbuf(struct file *file, struct v4l2_m2m_ctx *m2m_ctx, struct v4l2_exportbuffer *eb); @@ -132,6 +138,18 @@ struct v4l2_m2m_ctx *v4l2_m2m_ctx_init(struct v4l2_m2m_dev *m2m_dev, void *drv_priv, int (*queue_init)(void *priv, struct vb2_queue *src_vq, struct vb2_queue *dst_vq)); +static inline void v4l2_m2m_set_src_buffered(struct v4l2_m2m_ctx *m2m_ctx, + bool buffered) +{ + m2m_ctx->out_q_ctx.buffered = buffered; +} + +static inline void v4l2_m2m_set_dst_buffered(struct v4l2_m2m_ctx *m2m_ctx, + bool buffered) +{ + m2m_ctx->cap_q_ctx.buffered = buffered; +} + void v4l2_m2m_ctx_release(struct v4l2_m2m_ctx *m2m_ctx); void v4l2_m2m_buf_queue(struct v4l2_m2m_ctx *m2m_ctx, struct vb2_buffer *vb); @@ -214,5 +232,26 @@ static inline void *v4l2_m2m_dst_buf_remove(struct v4l2_m2m_ctx *m2m_ctx) return v4l2_m2m_buf_remove(&m2m_ctx->cap_q_ctx); } +/* v4l2 ioctl helpers */ + +int v4l2_m2m_ioctl_reqbufs(struct file *file, void *priv, + struct v4l2_requestbuffers *rb); +int v4l2_m2m_ioctl_create_bufs(struct file *file, void *fh, + struct v4l2_create_buffers *create); +int v4l2_m2m_ioctl_querybuf(struct file *file, void *fh, + struct v4l2_buffer *buf); +int v4l2_m2m_ioctl_expbuf(struct file *file, void *fh, + struct v4l2_exportbuffer *eb); +int v4l2_m2m_ioctl_qbuf(struct file *file, void *fh, + struct v4l2_buffer *buf); +int v4l2_m2m_ioctl_dqbuf(struct file *file, void *fh, + struct v4l2_buffer *buf); +int v4l2_m2m_ioctl_streamon(struct file *file, void *fh, + enum v4l2_buf_type type); +int v4l2_m2m_ioctl_streamoff(struct file *file, void *fh, + enum v4l2_buf_type type); +int v4l2_m2m_fop_mmap(struct file *file, struct vm_area_struct *vma); +unsigned int v4l2_m2m_fop_poll(struct file *file, poll_table *wait); + #endif /* _MEDIA_V4L2_MEM2MEM_H */ diff --git a/include/media/v4l2-of.h b/include/media/v4l2-of.h index 3a8a84124b4..70fa7b7b048 100644 --- a/include/media/v4l2-of.h +++ b/include/media/v4l2-of.h @@ -17,6 +17,7 @@ #include <linux/list.h> #include <linux/types.h> #include <linux/errno.h> +#include <linux/of_graph.h> #include <media/v4l2-mediabus.h> @@ -50,19 +51,13 @@ struct v4l2_of_bus_parallel { /** * struct v4l2_of_endpoint - the endpoint data structure - * @port: identifier (value of reg property) of a port this endpoint belongs to - * @id: identifier (value of reg property) of this endpoint - * @local_node: pointer to device_node of this endpoint - * @remote: phandle to remote endpoint node + * @base: struct of_endpoint containing port, id, and local of_node * @bus_type: bus type * @bus: bus configuration data structure * @head: list head for this structure */ struct v4l2_of_endpoint { - unsigned int port; - unsigned int id; - const struct device_node *local_node; - const __be32 *remote; + struct of_endpoint base; enum v4l2_mbus_type bus_type; union { struct v4l2_of_bus_parallel parallel; @@ -72,13 +67,8 @@ struct v4l2_of_endpoint { }; #ifdef CONFIG_OF -void v4l2_of_parse_endpoint(const struct device_node *node, - struct v4l2_of_endpoint *link); -struct device_node *v4l2_of_get_next_endpoint(const struct device_node *parent, - struct device_node *previous); -struct device_node *v4l2_of_get_remote_port_parent( - const struct device_node *node); -struct device_node *v4l2_of_get_remote_port(const struct device_node *node); +int v4l2_of_parse_endpoint(const struct device_node *node, + struct v4l2_of_endpoint *endpoint); #else /* CONFIG_OF */ static inline int v4l2_of_parse_endpoint(const struct device_node *node, @@ -87,25 +77,6 @@ static inline int v4l2_of_parse_endpoint(const struct device_node *node, return -ENOSYS; } -static inline struct device_node *v4l2_of_get_next_endpoint( - const struct device_node *parent, - struct device_node *previous) -{ - return NULL; -} - -static inline struct device_node *v4l2_of_get_remote_port_parent( - const struct device_node *node) -{ - return NULL; -} - -static inline struct device_node *v4l2_of_get_remote_port( - const struct device_node *node) -{ - return NULL; -} - #endif /* CONFIG_OF */ #endif /* _V4L2_OF_H */ diff --git a/include/media/v4l2-subdev.h b/include/media/v4l2-subdev.h index 5298d678d0f..d7465725773 100644 --- a/include/media/v4l2-subdev.h +++ b/include/media/v4l2-subdev.h @@ -24,6 +24,7 @@ #include <linux/types.h> #include <linux/v4l2-subdev.h> #include <media/media-entity.h> +#include <media/v4l2-async.h> #include <media/v4l2-common.h> #include <media/v4l2-dev.h> #include <media/v4l2-fh.h> @@ -88,7 +89,6 @@ struct v4l2_decode_vbi_line { /* Core ops: it is highly recommended to implement at least these ops: - g_chip_ident log_status g_register s_register @@ -145,7 +145,6 @@ struct v4l2_subdev_io_pin_config { performed later. It must not sleep. *Called from an IRQ context*. */ struct v4l2_subdev_core_ops { - int (*g_chip_ident)(struct v4l2_subdev *sd, struct v4l2_dbg_chip_ident *chip); int (*log_status)(struct v4l2_subdev *sd); int (*s_io_pin_config)(struct v4l2_subdev *sd, size_t n, struct v4l2_subdev_io_pin_config *pincfg); @@ -160,9 +159,11 @@ struct v4l2_subdev_core_ops { int (*s_ext_ctrls)(struct v4l2_subdev *sd, struct v4l2_ext_controls *ctrls); int (*try_ext_ctrls)(struct v4l2_subdev *sd, struct v4l2_ext_controls *ctrls); int (*querymenu)(struct v4l2_subdev *sd, struct v4l2_querymenu *qm); - int (*g_std)(struct v4l2_subdev *sd, v4l2_std_id *norm); - int (*s_std)(struct v4l2_subdev *sd, v4l2_std_id norm); long (*ioctl)(struct v4l2_subdev *sd, unsigned int cmd, void *arg); +#ifdef CONFIG_COMPAT + long (*compat_ioctl32)(struct v4l2_subdev *sd, unsigned int cmd, + unsigned long arg); +#endif #ifdef CONFIG_VIDEO_ADV_DEBUG int (*g_register)(struct v4l2_subdev *sd, struct v4l2_dbg_register *reg); int (*s_register)(struct v4l2_subdev *sd, const struct v4l2_dbg_register *reg); @@ -193,6 +194,7 @@ struct v4l2_subdev_tuner_ops { int (*s_radio)(struct v4l2_subdev *sd); int (*s_frequency)(struct v4l2_subdev *sd, const struct v4l2_frequency *freq); int (*g_frequency)(struct v4l2_subdev *sd, struct v4l2_frequency *freq); + int (*enum_freq_bands)(struct v4l2_subdev *sd, struct v4l2_frequency_band *band); int (*g_tuner)(struct v4l2_subdev *sd, struct v4l2_tuner *vt); int (*s_tuner)(struct v4l2_subdev *sd, const struct v4l2_tuner *vt); int (*g_modulator)(struct v4l2_subdev *sd, struct v4l2_modulator *vm); @@ -230,15 +232,18 @@ struct v4l2_subdev_audio_ops { /* Indicates the @length field specifies maximum data length. */ #define V4L2_MBUS_FRAME_DESC_FL_LEN_MAX (1U << 0) -/* Indicates user defined data format, i.e. non standard frame format. */ +/* + * Indicates that the format does not have line offsets, i.e. the + * receiver should use 1D DMA. + */ #define V4L2_MBUS_FRAME_DESC_FL_BLOB (1U << 1) /** * struct v4l2_mbus_frame_desc_entry - media bus frame description structure * @flags: V4L2_MBUS_FRAME_DESC_FL_* flags * @pixelcode: media bus pixel code, valid if FRAME_DESC_FL_BLOB is not set - * @length: number of octets per frame, valid for compressed or unspecified - * formats + * @length: number of octets per frame, valid if V4L2_MBUS_FRAME_DESC_FL_BLOB + * is set */ struct v4l2_mbus_frame_desc_entry { u16 flags; @@ -265,8 +270,11 @@ struct v4l2_mbus_frame_desc { g_std_output: get current standard for video OUTPUT devices. This is ignored by video input devices. - g_tvnorms_output: get v4l2_std_id with all standards supported by video - OUTPUT device. This is ignored by video input devices. + g_tvnorms: get v4l2_std_id with all standards supported by the video + CAPTURE device. This is ignored by video output devices. + + g_tvnorms_output: get v4l2_std_id with all standards supported by the video + OUTPUT device. This is ignored by video capture devices. s_crystal_freq: sets the frequency of the crystal used to generate the clocks in Hz. An extra flags field allows device specific configuration @@ -306,9 +314,12 @@ struct v4l2_mbus_frame_desc { struct v4l2_subdev_video_ops { int (*s_routing)(struct v4l2_subdev *sd, u32 input, u32 output, u32 config); int (*s_crystal_freq)(struct v4l2_subdev *sd, u32 freq, u32 flags); + int (*g_std)(struct v4l2_subdev *sd, v4l2_std_id *norm); + int (*s_std)(struct v4l2_subdev *sd, v4l2_std_id norm); int (*s_std_output)(struct v4l2_subdev *sd, v4l2_std_id std); int (*g_std_output)(struct v4l2_subdev *sd, v4l2_std_id *std); int (*querystd)(struct v4l2_subdev *sd, v4l2_std_id *std); + int (*g_tvnorms)(struct v4l2_subdev *sd, v4l2_std_id *std); int (*g_tvnorms_output)(struct v4l2_subdev *sd, v4l2_std_id *std); int (*g_input_status)(struct v4l2_subdev *sd, u32 *status); int (*s_stream)(struct v4l2_subdev *sd, int enable); @@ -327,12 +338,8 @@ struct v4l2_subdev_video_ops { struct v4l2_dv_timings *timings); int (*g_dv_timings)(struct v4l2_subdev *sd, struct v4l2_dv_timings *timings); - int (*enum_dv_timings)(struct v4l2_subdev *sd, - struct v4l2_enum_dv_timings *timings); int (*query_dv_timings)(struct v4l2_subdev *sd, struct v4l2_dv_timings *timings); - int (*dv_timings_cap)(struct v4l2_subdev *sd, - struct v4l2_dv_timings_cap *cap); int (*enum_mbus_fmt)(struct v4l2_subdev *sd, unsigned int index, enum v4l2_mbus_pixelcode *code); int (*enum_mbus_fsizes)(struct v4l2_subdev *sd, @@ -504,8 +511,12 @@ struct v4l2_subdev_pad_ops { struct v4l2_subdev_selection *sel); int (*set_selection)(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh, struct v4l2_subdev_selection *sel); - int (*get_edid)(struct v4l2_subdev *sd, struct v4l2_subdev_edid *edid); - int (*set_edid)(struct v4l2_subdev *sd, struct v4l2_subdev_edid *edid); + int (*get_edid)(struct v4l2_subdev *sd, struct v4l2_edid *edid); + int (*set_edid)(struct v4l2_subdev *sd, struct v4l2_edid *edid); + int (*dv_timings_cap)(struct v4l2_subdev *sd, + struct v4l2_dv_timings_cap *cap); + int (*enum_dv_timings)(struct v4l2_subdev *sd, + struct v4l2_enum_dv_timings *timings); #ifdef CONFIG_MEDIA_CONTROLLER int (*link_validate)(struct v4l2_subdev *sd, struct media_link *link, struct v4l2_subdev_format *source_fmt, @@ -560,6 +571,17 @@ struct v4l2_subdev_internal_ops { /* Set this flag if this subdev generates events. */ #define V4L2_SUBDEV_FL_HAS_EVENTS (1U << 3) +struct regulator_bulk_data; + +struct v4l2_subdev_platform_data { + /* Optional regulators uset to power on/off the subdevice */ + struct regulator_bulk_data *regulators; + int num_regulators; + + /* Per-subdevice data, specific for a certain video host device */ + void *host_priv; +}; + /* Each instance of a subdev driver should create this struct, either stand-alone or embedded in a larger struct. */ @@ -569,6 +591,7 @@ struct v4l2_subdev { #endif struct list_head list; struct module *owner; + bool owner_v4l2_dev; u32 flags; struct v4l2_device *v4l2_dev; const struct v4l2_subdev_ops *ops; @@ -585,6 +608,16 @@ struct v4l2_subdev { void *host_priv; /* subdev device node */ struct video_device *devnode; + /* pointer to the physical device, if any */ + struct device *dev; + /* Links this subdev to a global subdev_list or @notifier->done list. */ + struct list_head async_list; + /* Pointer to respective struct v4l2_async_subdev. */ + struct v4l2_async_subdev *asd; + /* Pointer to the managing notifier. */ + struct v4l2_async_notifier *notifier; + /* common part of subdevice platform data */ + struct v4l2_subdev_platform_data *pdata; }; #define media_entity_to_v4l2_subdev(ent) \ @@ -615,13 +648,13 @@ struct v4l2_subdev_fh { v4l2_subdev_get_try_##fun_name(struct v4l2_subdev_fh *fh, \ unsigned int pad) \ { \ - BUG_ON(unlikely(pad >= vdev_to_v4l2_subdev( \ - fh->vfh.vdev)->entity.num_pads)); \ + BUG_ON(pad >= vdev_to_v4l2_subdev( \ + fh->vfh.vdev)->entity.num_pads); \ return &fh->pad[pad].field_name; \ } __V4L2_SUBDEV_MK_GET_TRY(v4l2_mbus_framefmt, format, try_fmt) -__V4L2_SUBDEV_MK_GET_TRY(v4l2_rect, crop, try_compose) +__V4L2_SUBDEV_MK_GET_TRY(v4l2_rect, crop, try_crop) __V4L2_SUBDEV_MK_GET_TRY(v4l2_rect, compose, try_compose) #endif @@ -660,17 +693,12 @@ void v4l2_subdev_init(struct v4l2_subdev *sd, /* Call an ops of a v4l2_subdev, doing the right checks against NULL pointers. - Example: err = v4l2_subdev_call(sd, core, g_chip_ident, &chip); + Example: err = v4l2_subdev_call(sd, video, s_std, norm); */ #define v4l2_subdev_call(sd, o, f, args...) \ (!(sd) ? -ENODEV : (((sd)->ops->o && (sd)->ops->o->f) ? \ (sd)->ops->o->f((sd) , ##args) : -ENOIOCTLCMD)) -/* Send a notification to v4l2_device. */ -#define v4l2_subdev_notify(sd, notification, arg) \ - ((!(sd) || !(sd)->v4l2_dev || !(sd)->v4l2_dev->notify) ? -ENODEV : \ - (sd)->v4l2_dev->notify((sd), (notification), (arg))) - #define v4l2_subdev_has_op(sd, o, f) \ ((sd)->ops->o && (sd)->ops->o->f) diff --git a/include/media/videobuf2-core.h b/include/media/videobuf2-core.h index d88a098d1af..8fab6fa0dbf 100644 --- a/include/media/videobuf2-core.h +++ b/include/media/videobuf2-core.h @@ -20,6 +20,7 @@ struct vb2_alloc_ctx; struct vb2_fileio_data; +struct vb2_threadio_data; /** * struct vb2_mem_ops - memory handling/memory allocator operations @@ -34,56 +35,56 @@ struct vb2_fileio_data; * usually will result in the allocator freeing the buffer (if * no other users of this buffer are present); the buf_priv * argument is the allocator private per-buffer structure - * previously returned from the alloc callback + * previously returned from the alloc callback. * @get_userptr: acquire userspace memory for a hardware operation; used for * USERPTR memory types; vaddr is the address passed to the * videobuf layer when queuing a video buffer of USERPTR type; * should return an allocator private per-buffer structure * associated with the buffer on success, NULL on failure; * the returned private structure will then be passed as buf_priv - * argument to other ops in this structure + * argument to other ops in this structure. * @put_userptr: inform the allocator that a USERPTR buffer will no longer - * be used + * be used. * @attach_dmabuf: attach a shared struct dma_buf for a hardware operation; * used for DMABUF memory types; alloc_ctx is the alloc context * dbuf is the shared dma_buf; returns NULL on failure; * allocator private per-buffer structure on success; - * this needs to be used for further accesses to the buffer + * this needs to be used for further accesses to the buffer. * @detach_dmabuf: inform the exporter of the buffer that the current DMABUF * buffer is no longer used; the buf_priv argument is the * allocator private per-buffer structure previously returned - * from the attach_dmabuf callback + * from the attach_dmabuf callback. * @map_dmabuf: request for access to the dmabuf from allocator; the allocator * of dmabuf is informed that this driver is going to use the - * dmabuf + * dmabuf. * @unmap_dmabuf: releases access control to the dmabuf - allocator is notified - * that this driver is done using the dmabuf for now + * that this driver is done using the dmabuf for now. * @prepare: called every time the buffer is passed from userspace to the - * driver, useful for cache synchronisation, optional + * driver, useful for cache synchronisation, optional. * @finish: called every time the buffer is passed back from the driver - * to the userspace, also optional + * to the userspace, also optional. * @vaddr: return a kernel virtual address to a given memory buffer * associated with the passed private structure or NULL if no - * such mapping exists + * such mapping exists. * @cookie: return allocator specific cookie for a given memory buffer * associated with the passed private structure or NULL if not - * available + * available. * @num_users: return the current number of users of a memory buffer; * return 1 if the videobuf layer (or actually the driver using - * it) is the only user + * it) is the only user. * @mmap: setup a userspace mapping for a given memory buffer under - * the provided virtual memory region + * the provided virtual memory region. * * Required ops for USERPTR types: get_userptr, put_userptr. * Required ops for MMAP types: alloc, put, num_users, mmap. - * Required ops for read/write access types: alloc, put, num_users, vaddr + * Required ops for read/write access types: alloc, put, num_users, vaddr. * Required ops for DMABUF types: attach_dmabuf, detach_dmabuf, map_dmabuf, * unmap_dmabuf. */ struct vb2_mem_ops { void *(*alloc)(void *alloc_ctx, unsigned long size, gfp_t gfp_flags); void (*put)(void *buf_priv); - struct dma_buf *(*get_dmabuf)(void *buf_priv); + struct dma_buf *(*get_dmabuf)(void *buf_priv, unsigned long flags); void *(*get_userptr)(void *alloc_ctx, unsigned long vaddr, unsigned long size, int write); @@ -142,6 +143,7 @@ enum vb2_fileio_flags { /** * enum vb2_buffer_state - current video buffer state * @VB2_BUF_STATE_DEQUEUED: buffer under userspace control + * @VB2_BUF_STATE_PREPARING: buffer is being prepared in videobuf * @VB2_BUF_STATE_PREPARED: buffer prepared in videobuf and by the driver * @VB2_BUF_STATE_QUEUED: buffer queued in videobuf, but not in driver * @VB2_BUF_STATE_ACTIVE: buffer queued in driver and possibly used @@ -154,6 +156,7 @@ enum vb2_fileio_flags { */ enum vb2_buffer_state { VB2_BUF_STATE_DEQUEUED, + VB2_BUF_STATE_PREPARING, VB2_BUF_STATE_PREPARED, VB2_BUF_STATE_QUEUED, VB2_BUF_STATE_ACTIVE, @@ -201,6 +204,37 @@ struct vb2_buffer { struct list_head done_entry; struct vb2_plane planes[VIDEO_MAX_PLANES]; + +#ifdef CONFIG_VIDEO_ADV_DEBUG + /* + * Counters for how often these buffer-related ops are + * called. Used to check for unbalanced ops. + */ + u32 cnt_mem_alloc; + u32 cnt_mem_put; + u32 cnt_mem_get_dmabuf; + u32 cnt_mem_get_userptr; + u32 cnt_mem_put_userptr; + u32 cnt_mem_prepare; + u32 cnt_mem_finish; + u32 cnt_mem_attach_dmabuf; + u32 cnt_mem_detach_dmabuf; + u32 cnt_mem_map_dmabuf; + u32 cnt_mem_unmap_dmabuf; + u32 cnt_mem_vaddr; + u32 cnt_mem_cookie; + u32 cnt_mem_num_users; + u32 cnt_mem_mmap; + + u32 cnt_buf_init; + u32 cnt_buf_prepare; + u32 cnt_buf_finish; + u32 cnt_buf_cleanup; + u32 cnt_buf_queue; + + /* This counts the number of calls to vb2_buffer_done() */ + u32 cnt_buf_done; +#endif }; /** @@ -219,38 +253,52 @@ struct vb2_buffer { * configured format and *num_buffers is the total number * of buffers, that are being allocated. When called from * VIDIOC_CREATE_BUFS, fmt != NULL and it describes the - * target frame format. In this case *num_buffers are being - * allocated additionally to q->num_buffers. + * target frame format (if the format isn't valid the + * callback must return -EINVAL). In this case *num_buffers + * are being allocated additionally to q->num_buffers. * @wait_prepare: release any locks taken while calling vb2 functions; * it is called before an ioctl needs to wait for a new * buffer to arrive; required to avoid a deadlock in - * blocking access type + * blocking access type. * @wait_finish: reacquire all locks released in the previous callback; * required to continue operation after sleeping while - * waiting for a new buffer to arrive + * waiting for a new buffer to arrive. * @buf_init: called once after allocating a buffer (in MMAP case) * or after acquiring a new USERPTR buffer; drivers may * perform additional buffer-related initialization; * initialization failure (return != 0) will prevent - * queue setup from completing successfully; optional + * queue setup from completing successfully; optional. * @buf_prepare: called every time the buffer is queued from userspace * and from the VIDIOC_PREPARE_BUF ioctl; drivers may * perform any initialization required before each hardware - * operation in this callback; if an error is returned, the - * buffer will not be queued in driver; optional + * operation in this callback; drivers that support + * VIDIOC_CREATE_BUFS must also validate the buffer size; + * if an error is returned, the buffer will not be queued + * in driver; optional. * @buf_finish: called before every dequeue of the buffer back to * userspace; drivers may perform any operations required - * before userspace accesses the buffer; optional + * before userspace accesses the buffer; optional. The + * buffer state can be one of the following: DONE and + * ERROR occur while streaming is in progress, and the + * PREPARED state occurs when the queue has been canceled + * and all pending buffers are being returned to their + * default DEQUEUED state. Typically you only have to do + * something if the state is VB2_BUF_STATE_DONE, since in + * all other cases the buffer contents will be ignored + * anyway. * @buf_cleanup: called once before the buffer is freed; drivers may - * perform any additional cleanup; optional + * perform any additional cleanup; optional. * @start_streaming: called once to enter 'streaming' state; the driver may * receive buffers with @buf_queue callback before * @start_streaming is called; the driver gets the number * of already queued buffers in count parameter; driver - * can return an error if hardware fails or not enough - * buffers has been queued, in such case all buffers that - * have been already given by the @buf_queue callback are - * invalidated. + * can return an error if hardware fails, in that case all + * buffers that have been already given by the @buf_queue + * callback are invalidated. + * If there were not enough queued buffers to start + * streaming, then this callback returns -ENOBUFS, and the + * vb2 core will retry calling @start_streaming when a new + * buffer is queued. * @stop_streaming: called when 'streaming' state must be disabled; driver * should stop any DMA transactions or wait until they * finish and give back all buffers it got from buf_queue() @@ -260,7 +308,7 @@ struct vb2_buffer { * the buffer back by calling vb2_buffer_done() function; * it is allways called after calling STREAMON ioctl; * might be called before start_streaming callback if user - * pre-queued buffers before calling STREAMON + * pre-queued buffers before calling STREAMON. */ struct vb2_ops { int (*queue_setup)(struct vb2_queue *q, const struct v4l2_format *fmt, @@ -272,11 +320,11 @@ struct vb2_ops { int (*buf_init)(struct vb2_buffer *vb); int (*buf_prepare)(struct vb2_buffer *vb); - int (*buf_finish)(struct vb2_buffer *vb); + void (*buf_finish)(struct vb2_buffer *vb); void (*buf_cleanup)(struct vb2_buffer *vb); int (*start_streaming)(struct vb2_queue *q, unsigned int count); - int (*stop_streaming)(struct vb2_queue *q); + void (*stop_streaming)(struct vb2_queue *q); void (*buf_queue)(struct vb2_buffer *vb); }; @@ -304,21 +352,31 @@ struct v4l2_fh; * @buf_struct_size: size of the driver-specific buffer structure; * "0" indicates the driver doesn't want to use a custom buffer * structure type, so sizeof(struct vb2_buffer) will is used + * @timestamp_flags: Timestamp flags; V4L2_BUF_FLAGS_TIMESTAMP_* and + * V4L2_BUF_FLAGS_TSTAMP_SRC_* * @gfp_flags: additional gfp flags used when allocating the buffers. * Typically this is 0, but it may be e.g. GFP_DMA or __GFP_DMA32 * to force the buffer allocation to a specific memory zone. + * @min_buffers_needed: the minimum number of buffers needed before + * start_streaming() can be called. Used when a DMA engine + * cannot be started unless at least this number of buffers + * have been queued into the driver. * * @memory: current memory type used * @bufs: videobuf buffer structures * @num_buffers: number of allocated/used buffers * @queued_list: list of buffers currently queued from userspace - * @queued_count: number of buffers owned by the driver + * @queued_count: number of buffers queued and ready for streaming. + * @owned_by_drv_count: number of buffers owned by the driver * @done_list: list of buffers ready to be dequeued to userspace * @done_lock: lock to protect done_list list * @done_wq: waitqueue for processes waiting for buffers ready to be dequeued * @alloc_ctx: memory type/allocator-specific contexts for each plane * @streaming: current streaming state + * @start_streaming_called: start_streaming() was called successfully and we + * started streaming. * @fileio: file io emulator internal data, used only if emulator is active + * @threadio: thread io internal data, used only if thread is active */ struct vb2_queue { enum v4l2_buf_type type; @@ -331,8 +389,9 @@ struct vb2_queue { const struct vb2_mem_ops *mem_ops; void *drv_priv; unsigned int buf_struct_size; - u32 timestamp_type; + u32 timestamp_flags; gfp_t gfp_flags; + u32 min_buffers_needed; /* private: internal use only */ enum v4l2_memory memory; @@ -340,8 +399,9 @@ struct vb2_queue { unsigned int num_buffers; struct list_head queued_list; + unsigned int queued_count; - atomic_t queued_count; + atomic_t owned_by_drv_count; struct list_head done_list; spinlock_t done_lock; wait_queue_head_t done_wq; @@ -350,14 +410,29 @@ struct vb2_queue { unsigned int plane_sizes[VIDEO_MAX_PLANES]; unsigned int streaming:1; + unsigned int start_streaming_called:1; struct vb2_fileio_data *fileio; + struct vb2_threadio_data *threadio; + +#ifdef CONFIG_VIDEO_ADV_DEBUG + /* + * Counters for how often these queue-related ops are + * called. Used to check for unbalanced ops. + */ + u32 cnt_queue_setup; + u32 cnt_wait_prepare; + u32 cnt_wait_finish; + u32 cnt_start_streaming; + u32 cnt_stop_streaming; +#endif }; void *vb2_plane_vaddr(struct vb2_buffer *vb, unsigned int plane_no); void *vb2_plane_cookie(struct vb2_buffer *vb, unsigned int plane_no); void vb2_buffer_done(struct vb2_buffer *vb, enum vb2_buffer_state state); +void vb2_discard_done(struct vb2_queue *q); int vb2_wait_for_all_buffers(struct vb2_queue *q); int vb2_querybuf(struct vb2_queue *q, struct v4l2_buffer *b); @@ -388,8 +463,37 @@ unsigned long vb2_get_unmapped_area(struct vb2_queue *q, unsigned int vb2_poll(struct vb2_queue *q, struct file *file, poll_table *wait); size_t vb2_read(struct vb2_queue *q, char __user *data, size_t count, loff_t *ppos, int nonblock); -size_t vb2_write(struct vb2_queue *q, char __user *data, size_t count, +size_t vb2_write(struct vb2_queue *q, const char __user *data, size_t count, loff_t *ppos, int nonblock); +/** + * vb2_thread_fnc - callback function for use with vb2_thread + * + * This is called whenever a buffer is dequeued in the thread. + */ +typedef int (*vb2_thread_fnc)(struct vb2_buffer *vb, void *priv); + +/** + * vb2_thread_start() - start a thread for the given queue. + * @q: videobuf queue + * @fnc: callback function + * @priv: priv pointer passed to the callback function + * @thread_name:the name of the thread. This will be prefixed with "vb2-". + * + * This starts a thread that will queue and dequeue until an error occurs + * or @vb2_thread_stop is called. + * + * This function should not be used for anything else but the videobuf2-dvb + * support. If you think you have another good use-case for this, then please + * contact the linux-media mailinglist first. + */ +int vb2_thread_start(struct vb2_queue *q, vb2_thread_fnc fnc, void *priv, + const char *thread_name); + +/** + * vb2_thread_stop() - stop the thread for the given queue. + * @q: videobuf queue + */ +int vb2_thread_stop(struct vb2_queue *q); /** * vb2_is_streaming() - return streaming status of the queue @@ -401,6 +505,23 @@ static inline bool vb2_is_streaming(struct vb2_queue *q) } /** + * vb2_fileio_is_active() - return true if fileio is active. + * @q: videobuf queue + * + * This returns true if read() or write() is used to stream the data + * as opposed to stream I/O. This is almost never an important distinction, + * except in rare cases. One such case is that using read() or write() to + * stream a format using V4L2_FIELD_ALTERNATE is not allowed since there + * is no way you can pass the field information of each buffer to/from + * userspace. A driver that supports this field format should check for + * this in the queue_setup op and reject it if this function returns true. + */ +static inline bool vb2_fileio_is_active(struct vb2_queue *q) +{ + return q->fileio; +} + +/** * vb2_is_busy() - return busy status of the queue * @q: videobuf queue * @@ -488,7 +609,8 @@ int vb2_ioctl_expbuf(struct file *file, void *priv, int vb2_fop_mmap(struct file *file, struct vm_area_struct *vma); int vb2_fop_release(struct file *file); -ssize_t vb2_fop_write(struct file *file, char __user *buf, +int _vb2_fop_release(struct file *file, struct mutex *lock); +ssize_t vb2_fop_write(struct file *file, const char __user *buf, size_t count, loff_t *ppos); ssize_t vb2_fop_read(struct file *file, char __user *buf, size_t count, loff_t *ppos); diff --git a/include/media/videobuf2-dma-sg.h b/include/media/videobuf2-dma-sg.h index 0038526b8ef..7b89852779a 100644 --- a/include/media/videobuf2-dma-sg.h +++ b/include/media/videobuf2-dma-sg.h @@ -15,16 +15,10 @@ #include <media/videobuf2-core.h> -struct vb2_dma_sg_desc { - unsigned long size; - unsigned int num_pages; - struct scatterlist *sglist; -}; - -static inline struct vb2_dma_sg_desc *vb2_dma_sg_plane_desc( +static inline struct sg_table *vb2_dma_sg_plane_desc( struct vb2_buffer *vb, unsigned int plane_no) { - return (struct vb2_dma_sg_desc *)vb2_plane_cookie(vb, plane_no); + return (struct sg_table *)vb2_plane_cookie(vb, plane_no); } extern const struct vb2_mem_ops vb2_dma_sg_memops; diff --git a/include/media/videobuf2-dvb.h b/include/media/videobuf2-dvb.h new file mode 100644 index 00000000000..8f61456f139 --- /dev/null +++ b/include/media/videobuf2-dvb.h @@ -0,0 +1,58 @@ +#ifndef _VIDEOBUF2_DVB_H_ +#define _VIDEOBUF2_DVB_H_ + +#include <dvbdev.h> +#include <dmxdev.h> +#include <dvb_demux.h> +#include <dvb_net.h> +#include <dvb_frontend.h> +#include <media/videobuf2-core.h> + +struct vb2_dvb { + /* filling that the job of the driver */ + char *name; + struct dvb_frontend *frontend; + struct vb2_queue dvbq; + + /* video-buf-dvb state info */ + struct mutex lock; + int nfeeds; + + /* vb2_dvb_(un)register manages this */ + struct dvb_demux demux; + struct dmxdev dmxdev; + struct dmx_frontend fe_hw; + struct dmx_frontend fe_mem; + struct dvb_net net; +}; + +struct vb2_dvb_frontend { + struct list_head felist; + int id; + struct vb2_dvb dvb; +}; + +struct vb2_dvb_frontends { + struct list_head felist; + struct mutex lock; + struct dvb_adapter adapter; + int active_fe_id; /* Indicates which frontend in the felist is in use */ + int gate; /* Frontend with gate control 0=!MFE,1=fe0,2=fe1 etc */ +}; + +int vb2_dvb_register_bus(struct vb2_dvb_frontends *f, + struct module *module, + void *adapter_priv, + struct device *device, + short *adapter_nr, + int mfe_shared); + +void vb2_dvb_unregister_bus(struct vb2_dvb_frontends *f); + +struct vb2_dvb_frontend *vb2_dvb_alloc_frontend(struct vb2_dvb_frontends *f, int id); +void vb2_dvb_dealloc_frontends(struct vb2_dvb_frontends *f); + +struct vb2_dvb_frontend *vb2_dvb_get_frontend(struct vb2_dvb_frontends *f, int id); +int vb2_dvb_find_frontend(struct vb2_dvb_frontends *f, struct dvb_frontend *p); + +#endif /* _VIDEOBUF2_DVB_H_ */ |