diff options
Diffstat (limited to 'drivers/usb/musb/Kconfig')
| -rw-r--r-- | drivers/usb/musb/Kconfig | 201 |
1 files changed, 91 insertions, 110 deletions
diff --git a/drivers/usb/musb/Kconfig b/drivers/usb/musb/Kconfig index 13093481f91..06cc5d6ea68 100644 --- a/drivers/usb/musb/Kconfig +++ b/drivers/usb/musb/Kconfig @@ -3,18 +3,10 @@ # for silicon based on Mentor Graphics INVENTRA designs # -comment "Enable Host or Gadget support to see Inventra options" - depends on !USB && USB_GADGET=n - # (M)HDRC = (Multipoint) Highspeed Dual-Role Controller config USB_MUSB_HDRC - depends on (USB || USB_GADGET) - depends on (ARM || (BF54x && !BF544) || (BF52x && !BF522 && !BF523)) - select NOP_USB_XCEIV if (ARCH_DAVINCI || MACH_OMAP3EVM || BLACKFIN) - select TWL4030_USB if MACH_OMAP_3430SDP - select TWL6030_USB if MACH_OMAP_4430SDP || MACH_OMAP4_PANDA - select USB_OTG_UTILS tristate 'Inventra Highspeed Dual Role Controller (TI, ADI, ...)' + depends on (USB || USB_GADGET) help Say Y here if your system has a dual role high speed USB controller based on the Mentor Graphics silicon IP. Then @@ -22,7 +14,7 @@ config USB_MUSB_HDRC it's being used with, including the USB peripheral role, or the USB host role, or both. - Texas Instruments familiies using this IP include DaVinci + Texas Instruments families using this IP include DaVinci (35x, 644x ...), OMAP 243x, OMAP 3, and TUSB 6010. Analog Devices parts using this IP include Blackfin BF54x, @@ -33,153 +25,142 @@ config USB_MUSB_HDRC To compile this driver as a module, choose M here; the module will be called "musb-hdrc". +if USB_MUSB_HDRC + +choice + bool "MUSB Mode Selection" + default USB_MUSB_DUAL_ROLE if (USB && USB_GADGET) + default USB_MUSB_HOST if (USB && !USB_GADGET) + default USB_MUSB_GADGET if (!USB && USB_GADGET) + +config USB_MUSB_HOST + bool "Host only mode" + depends on USB=y || USB=USB_MUSB_HDRC + help + Select this when you want to use MUSB in host mode only, + thereby the gadget feature will be regressed. + +config USB_MUSB_GADGET + bool "Gadget only mode" + depends on USB_GADGET=y || USB_GADGET=USB_MUSB_HDRC + depends on HAS_DMA + help + Select this when you want to use MUSB in gadget mode only, + thereby the host feature will be regressed. + +config USB_MUSB_DUAL_ROLE + bool "Dual Role mode" + depends on ((USB=y || USB=USB_MUSB_HDRC) && (USB_GADGET=y || USB_GADGET=USB_MUSB_HDRC)) + depends on HAS_DMA + help + This is the default mode of working of MUSB controller where + both host and gadget features are enabled. + +endchoice + choice prompt "Platform Glue Layer" - depends on USB_MUSB_HDRC config USB_MUSB_DAVINCI tristate "DaVinci" depends on ARCH_DAVINCI_DMx + depends on BROKEN config USB_MUSB_DA8XX tristate "DA8xx/OMAP-L1x" depends on ARCH_DAVINCI_DA8XX + depends on BROKEN config USB_MUSB_TUSB6010 tristate "TUSB6010" - depends on ARCH_OMAP config USB_MUSB_OMAP2PLUS tristate "OMAP2430 and onwards" - depends on ARCH_OMAP2PLUS + depends on ARCH_OMAP2PLUS && USB + select GENERIC_PHY config USB_MUSB_AM35X tristate "AM35x" depends on ARCH_OMAP +config USB_MUSB_DSPS + tristate "TI DSPS platforms" + select USB_MUSB_AM335X_CHILD + depends on OF_IRQ + config USB_MUSB_BLACKFIN tristate "Blackfin" depends on (BF54x && !BF544) || (BF52x && ! BF522 && !BF523) config USB_MUSB_UX500 - tristate "U8500 and U5500" - depends on (ARCH_U8500 && AB8500_USB) || (ARCH_U5500) - -endchoice - -choice - prompt "Driver Mode" - depends on USB_MUSB_HDRC - help - Dual-Role devices can support both host and peripheral roles, - as well as a the special "OTG Device" role which can switch - between both roles as needed. - -# use USB_MUSB_HDRC_HCD not USB_MUSB_HOST to #ifdef host side support; -# OTG needs both roles, not just USB_MUSB_HOST. -config USB_MUSB_HOST - depends on USB - bool "USB Host" - help - Say Y here if your system supports the USB host role. - If it has a USB "A" (rectangular), "Mini-A" (uncommon), - or "Mini-AB" connector, it supports the host role. - (With a "Mini-AB" connector, you should enable USB OTG.) - -# use USB_GADGET_MUSB_HDRC not USB_MUSB_PERIPHERAL to #ifdef peripheral -# side support ... OTG needs both roles -config USB_MUSB_PERIPHERAL - depends on USB_GADGET - bool "USB Peripheral (gadget stack)" - select USB_GADGET_MUSB_HDRC - help - Say Y here if your system supports the USB peripheral role. - If it has a USB "B" (squarish), "Mini-B", or "Mini-AB" - connector, it supports the peripheral role. - (With a "Mini-AB" connector, you should enable USB OTG.) - -config USB_MUSB_OTG - depends on USB && USB_GADGET && PM && EXPERIMENTAL - bool "Both host and peripheral: USB OTG (On The Go) Device" - select USB_GADGET_MUSB_HDRC - select USB_OTG - help - The most notable feature of USB OTG is support for a - "Dual-Role" device, which can act as either a device - or a host. The initial role choice can be changed - later, when two dual-role devices talk to each other. + tristate "Ux500 platforms" - At this writing, the OTG support in this driver is incomplete, - omitting the mandatory HNP or SRP protocols. However, some - of the cable based role switching works. (That is, grounding - the ID pin switches the controller to host mode, while leaving - it floating leaves it in peripheral mode.) - - Select this if your system has a Mini-AB connector, or - to simplify certain kinds of configuration. - - To implement your OTG Targeted Peripherals List (TPL), enable - USB_OTG_WHITELIST and update "drivers/usb/core/otg_whitelist.h" - to match your requirements. +config USB_MUSB_JZ4740 + tristate "JZ4740" + depends on MACH_JZ4740 || COMPILE_TEST + depends on USB_MUSB_GADGET + depends on USB_OTG_BLACKLIST_HUB endchoice -# enable peripheral support (including with OTG) -config USB_GADGET_MUSB_HDRC - bool - depends on USB_MUSB_HDRC && (USB_MUSB_PERIPHERAL || USB_MUSB_OTG) -# default y -# select USB_GADGET_DUALSPEED -# select USB_GADGET_SELECTED - -# enables host support (including with OTG) -config USB_MUSB_HDRC_HCD - bool - depends on USB_MUSB_HDRC && (USB_MUSB_HOST || USB_MUSB_OTG) - select USB_OTG if USB_GADGET_MUSB_HDRC - default y - +config USB_MUSB_AM335X_CHILD + tristate -config MUSB_PIO_ONLY - bool 'Disable DMA (always use PIO)' - depends on USB_MUSB_HDRC - default USB_MUSB_TUSB6010 || USB_MUSB_DA8XX || USB_MUSB_AM35X +choice + prompt 'MUSB DMA mode' + default MUSB_PIO_ONLY if ARCH_MULTIPLATFORM || USB_MUSB_JZ4740 + default USB_UX500_DMA if USB_MUSB_UX500 + default USB_INVENTRA_DMA if USB_MUSB_OMAP2PLUS || USB_MUSB_BLACKFIN + default USB_TI_CPPI_DMA if USB_MUSB_DAVINCI + default USB_TUSB_OMAP_DMA if USB_MUSB_TUSB6010 + default MUSB_PIO_ONLY if USB_MUSB_TUSB6010 || USB_MUSB_DA8XX || USB_MUSB_AM35X \ + || USB_MUSB_DSPS help - All data is copied between memory and FIFO by the CPU. - DMA controllers are ignored. - - Do not select 'n' here unless DMA support for your SOC or board - is unavailable (or unstable). When DMA is enabled at compile time, - you can still disable it at run time using the "use_dma=n" module - parameter. + Unfortunately, only one option can be enabled here. Ideally one + should be able to build all these drivers into one kernel to + allow using DMA on multiplatform kernels. config USB_UX500_DMA - bool - depends on USB_MUSB_HDRC && !MUSB_PIO_ONLY - default USB_MUSB_UX500 + bool 'ST Ericsson Ux500' + depends on USB_MUSB_UX500 help Enable DMA transfers on UX500 platforms. config USB_INVENTRA_DMA - bool - depends on USB_MUSB_HDRC && !MUSB_PIO_ONLY - default USB_MUSB_OMAP2PLUS || USB_MUSB_BLACKFIN + bool 'Inventra' + depends on USB_MUSB_OMAP2PLUS || USB_MUSB_BLACKFIN help Enable DMA transfers using Mentor's engine. config USB_TI_CPPI_DMA - bool - depends on USB_MUSB_HDRC && !MUSB_PIO_ONLY - default USB_MUSB_DAVINCI + bool 'TI CPPI (Davinci)' + depends on USB_MUSB_DAVINCI help Enable DMA transfers when TI CPPI DMA is available. +config USB_TI_CPPI41_DMA + bool 'TI CPPI 4.1 (AM335x)' + depends on ARCH_OMAP + select TI_CPPI41 + config USB_TUSB_OMAP_DMA - bool - depends on USB_MUSB_HDRC && !MUSB_PIO_ONLY - depends on USB_MUSB_TUSB6010 + bool 'TUSB 6010' + depends on USB_MUSB_TUSB6010 = USB_MUSB_HDRC # both built-in or both modules depends on ARCH_OMAP - default y help Enable DMA transfers on TUSB 6010 when OMAP DMA is available. +config MUSB_PIO_ONLY + bool 'Disable DMA (always use PIO)' + help + All data is copied between memory and FIFO by the CPU. + DMA controllers are ignored. + + Do not choose this unless DMA support for your SOC or board + is unavailable (or unstable). When DMA is enabled at compile time, + you can still disable it at run time using the "use_dma=n" module + parameter. + +endchoice + +endif # USB_MUSB_HDRC |