1 files changed, 167 insertions, 93 deletions

diff --git a/drivers/usb/host/xhci-pci.c b/drivers/usb/host/xhci-pci.c
index a10494c2f3c..e20520f4275 100644
--- a/drivers/usb/host/xhci-pci.c
+++ b/drivers/usb/host/xhci-pci.c
@@ -21,12 +21,22 @@
  */
 
 #include <linux/pci.h>
+#include <linux/slab.h>
+#include <linux/module.h>
 
 #include "xhci.h"
+#include "xhci-trace.h"
 
 /* Device for a quirk */
 #define PCI_VENDOR_ID_FRESCO_LOGIC	0x1b73
 #define PCI_DEVICE_ID_FRESCO_LOGIC_PDK	0x1000
+#define PCI_DEVICE_ID_FRESCO_LOGIC_FL1400	0x1400
+
+#define PCI_VENDOR_ID_ETRON		0x1b6f
+#define PCI_DEVICE_ID_ASROCK_P67	0x7023
+
+#define PCI_DEVICE_ID_INTEL_LYNXPOINT_XHCI	0x8c31
+#define PCI_DEVICE_ID_INTEL_LYNXPOINT_LP_XHCI	0x9c31
 
 static const char hcd_name[] = "xhci_hcd";
 
@@ -47,103 +57,118 @@ static int xhci_pci_reinit(struct xhci_hcd *xhci, struct pci_dev *pdev)
 	return 0;
 }
 
-/* called during probe() after chip reset completes */
-static int xhci_pci_setup(struct usb_hcd *hcd)
+static void xhci_pci_quirks(struct device *dev, struct xhci_hcd *xhci)
 {
-	struct xhci_hcd		*xhci;
-	struct pci_dev		*pdev = to_pci_dev(hcd->self.controller);
-	int			retval;
-	u32			temp;
-
-	hcd->self.sg_tablesize = TRBS_PER_SEGMENT - 2;
-
-	if (usb_hcd_is_primary_hcd(hcd)) {
-		xhci = kzalloc(sizeof(struct xhci_hcd), GFP_KERNEL);
-		if (!xhci)
-			return -ENOMEM;
-		*((struct xhci_hcd **) hcd->hcd_priv) = xhci;
-		xhci->main_hcd = hcd;
-		/* Mark the first roothub as being USB 2.0.
-		 * The xHCI driver will register the USB 3.0 roothub.
-		 */
-		hcd->speed = HCD_USB2;
-		hcd->self.root_hub->speed = USB_SPEED_HIGH;
-		/*
-		 * USB 2.0 roothub under xHCI has an integrated TT,
-		 * (rate matching hub) as opposed to having an OHCI/UHCI
-		 * companion controller.
-		 */
-		hcd->has_tt = 1;
-	} else {
-		/* xHCI private pointer was set in xhci_pci_probe for the second
-		 * registered roothub.
-		 */
-		xhci = hcd_to_xhci(hcd);
-		temp = xhci_readl(xhci, &xhci->cap_regs->hcc_params);
-		if (HCC_64BIT_ADDR(temp)) {
-			xhci_dbg(xhci, "Enabling 64-bit DMA addresses.\n");
-			dma_set_mask(hcd->self.controller, DMA_BIT_MASK(64));
-		} else {
-			dma_set_mask(hcd->self.controller, DMA_BIT_MASK(32));
-		}
-		return 0;
-	}
-
-	xhci->cap_regs = hcd->regs;
-	xhci->op_regs = hcd->regs +
-		HC_LENGTH(xhci_readl(xhci, &xhci->cap_regs->hc_capbase));
-	xhci->run_regs = hcd->regs +
-		(xhci_readl(xhci, &xhci->cap_regs->run_regs_off) & RTSOFF_MASK);
-	/* Cache read-only capability registers */
-	xhci->hcs_params1 = xhci_readl(xhci, &xhci->cap_regs->hcs_params1);
-	xhci->hcs_params2 = xhci_readl(xhci, &xhci->cap_regs->hcs_params2);
-	xhci->hcs_params3 = xhci_readl(xhci, &xhci->cap_regs->hcs_params3);
-	xhci->hcc_params = xhci_readl(xhci, &xhci->cap_regs->hc_capbase);
-	xhci->hci_version = HC_VERSION(xhci->hcc_params);
-	xhci->hcc_params = xhci_readl(xhci, &xhci->cap_regs->hcc_params);
-	xhci_print_registers(xhci);
+	struct pci_dev		*pdev = to_pci_dev(dev);
 
 	/* Look for vendor-specific quirks */
 	if (pdev->vendor == PCI_VENDOR_ID_FRESCO_LOGIC &&
-			pdev->device == PCI_DEVICE_ID_FRESCO_LOGIC_PDK &&
-			pdev->revision == 0x0) {
+			(pdev->device == PCI_DEVICE_ID_FRESCO_LOGIC_PDK ||
+			 pdev->device == PCI_DEVICE_ID_FRESCO_LOGIC_FL1400)) {
+		if (pdev->device == PCI_DEVICE_ID_FRESCO_LOGIC_PDK &&
+				pdev->revision == 0x0) {
 			xhci->quirks |= XHCI_RESET_EP_QUIRK;
-			xhci_dbg(xhci, "QUIRK: Fresco Logic xHC needs configure"
-					" endpoint cmd after reset endpoint\n");
+			xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
+				"QUIRK: Fresco Logic xHC needs configure"
+				" endpoint cmd after reset endpoint");
+		}
+		if (pdev->device == PCI_DEVICE_ID_FRESCO_LOGIC_PDK &&
+				pdev->revision == 0x4) {
+			xhci->quirks |= XHCI_SLOW_SUSPEND;
+			xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
+				"QUIRK: Fresco Logic xHC revision %u"
+				"must be suspended extra slowly",
+				pdev->revision);
+		}
+		/* Fresco Logic confirms: all revisions of this chip do not
+		 * support MSI, even though some of them claim to in their PCI
+		 * capabilities.
+		 */
+		xhci->quirks |= XHCI_BROKEN_MSI;
+		xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
+				"QUIRK: Fresco Logic revision %u "
+				"has broken MSI implementation",
+				pdev->revision);
+		xhci->quirks |= XHCI_TRUST_TX_LENGTH;
 	}
+
 	if (pdev->vendor == PCI_VENDOR_ID_NEC)
 		xhci->quirks |= XHCI_NEC_HOST;
 
+	if (pdev->vendor == PCI_VENDOR_ID_AMD && xhci->hci_version == 0x96)
+		xhci->quirks |= XHCI_AMD_0x96_HOST;
+
 	/* AMD PLL quirk */
 	if (pdev->vendor == PCI_VENDOR_ID_AMD && usb_amd_find_chipset_info())
 		xhci->quirks |= XHCI_AMD_PLL_FIX;
+	if (pdev->vendor == PCI_VENDOR_ID_INTEL) {
+		xhci->quirks |= XHCI_LPM_SUPPORT;
+		xhci->quirks |= XHCI_INTEL_HOST;
+	}
+	if (pdev->vendor == PCI_VENDOR_ID_INTEL &&
+			pdev->device == PCI_DEVICE_ID_INTEL_PANTHERPOINT_XHCI) {
+		xhci->quirks |= XHCI_EP_LIMIT_QUIRK;
+		xhci->limit_active_eps = 64;
+		xhci->quirks |= XHCI_SW_BW_CHECKING;
+		/*
+		 * PPT desktop boards DH77EB and DH77DF will power back on after
+		 * a few seconds of being shutdown.  The fix for this is to
+		 * switch the ports from xHCI to EHCI on shutdown.  We can't use
+		 * DMI information to find those particular boards (since each
+		 * vendor will change the board name), so we have to key off all
+		 * PPT chipsets.
+		 */
+		xhci->quirks |= XHCI_SPURIOUS_REBOOT;
+		xhci->quirks |= XHCI_AVOID_BEI;
+	}
+	if (pdev->vendor == PCI_VENDOR_ID_INTEL &&
+	    (pdev->device == PCI_DEVICE_ID_INTEL_LYNXPOINT_XHCI ||
+	     pdev->device == PCI_DEVICE_ID_INTEL_LYNXPOINT_LP_XHCI)) {
+		/* Workaround for occasional spurious wakeups from S5 (or
+		 * any other sleep) on Haswell machines with LPT and LPT-LP
+		 * with the new Intel BIOS
+		 */
+		/* Limit the quirk to only known vendors, as this triggers
+		 * yet another BIOS bug on some other machines
+		 * https://bugzilla.kernel.org/show_bug.cgi?id=66171
+		 */
+		if (pdev->subsystem_vendor == PCI_VENDOR_ID_HP)
+			xhci->quirks |= XHCI_SPURIOUS_WAKEUP;
+	}
+	if (pdev->vendor == PCI_VENDOR_ID_INTEL &&
+		pdev->device == PCI_DEVICE_ID_INTEL_LYNXPOINT_LP_XHCI) {
+		xhci->quirks |= XHCI_SPURIOUS_REBOOT;
+	}
+	if (pdev->vendor == PCI_VENDOR_ID_ETRON &&
+			pdev->device == PCI_DEVICE_ID_ASROCK_P67) {
+		xhci->quirks |= XHCI_RESET_ON_RESUME;
+		xhci->quirks |= XHCI_TRUST_TX_LENGTH;
+	}
+	if (pdev->vendor == PCI_VENDOR_ID_RENESAS &&
+			pdev->device == 0x0015)
+		xhci->quirks |= XHCI_RESET_ON_RESUME;
+	if (pdev->vendor == PCI_VENDOR_ID_VIA)
+		xhci->quirks |= XHCI_RESET_ON_RESUME;
+
+	if (xhci->quirks & XHCI_RESET_ON_RESUME)
+		xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
+				"QUIRK: Resetting on resume");
+}
 
-	/* Make sure the HC is halted. */
-	retval = xhci_halt(xhci);
-	if (retval)
-		goto error;
+/* called during probe() after chip reset completes */
+static int xhci_pci_setup(struct usb_hcd *hcd)
+{
+	struct xhci_hcd		*xhci;
+	struct pci_dev		*pdev = to_pci_dev(hcd->self.controller);
+	int			retval;
 
-	xhci_dbg(xhci, "Resetting HCD\n");
-	/* Reset the internal HC memory state and registers. */
-	retval = xhci_reset(xhci);
+	retval = xhci_gen_setup(hcd, xhci_pci_quirks);
 	if (retval)
-		goto error;
-	xhci_dbg(xhci, "Reset complete\n");
-
-	temp = xhci_readl(xhci, &xhci->cap_regs->hcc_params);
-	if (HCC_64BIT_ADDR(temp)) {
-		xhci_dbg(xhci, "Enabling 64-bit DMA addresses.\n");
-		dma_set_mask(hcd->self.controller, DMA_BIT_MASK(64));
-	} else {
-		dma_set_mask(hcd->self.controller, DMA_BIT_MASK(32));
-	}
+		return retval;
 
-	xhci_dbg(xhci, "Calling HCD init\n");
-	/* Initialize HCD and host controller data structures. */
-	retval = xhci_init(hcd);
-	if (retval)
-		goto error;
-	xhci_dbg(xhci, "Called HCD init\n");
+	xhci = hcd_to_xhci(hcd);
+	if (!usb_hcd_is_primary_hcd(hcd))
+		return 0;
 
 	pci_read_config_byte(pdev, XHCI_SBRN_OFFSET, &xhci->sbrn);
 	xhci_dbg(xhci, "Got SBRN %u\n", (unsigned int) xhci->sbrn);
@@ -153,7 +178,6 @@ static int xhci_pci_setup(struct usb_hcd *hcd)
 	if (!retval)
 		return retval;
 
-error:
 	kfree(xhci);
 	return retval;
 }
@@ -170,6 +194,10 @@ static int xhci_pci_probe(struct pci_dev *dev, const struct pci_device_id *id)
 	struct usb_hcd *hcd;
 
 	driver = (struct hc_driver *)id->driver_data;
+
+	/* Prevent runtime suspending between USB-2 and USB-3 initialization */
+	pm_runtime_get_noresume(&dev->dev);
+
 	/* Register the USB 2.0 roothub.
 	 * FIXME: USB core must know to register the USB 2.0 roothub first.
 	 * This is sort of silly, because we could just set the HCD driver flags
@@ -179,7 +207,7 @@ static int xhci_pci_probe(struct pci_dev *dev, const struct pci_device_id *id)
 	retval = usb_hcd_pci_probe(dev, id);
 
 	if (retval)
-		return retval;
+		goto put_runtime_pm;
 
 	/* USB 2.0 roothub is stored in the PCI device now. */
 	hcd = dev_get_drvdata(&dev->dev);
@@ -197,16 +225,25 @@ static int xhci_pci_probe(struct pci_dev *dev, const struct pci_device_id *id)
 	*((struct xhci_hcd **) xhci->shared_hcd->hcd_priv) = xhci;
 
 	retval = usb_add_hcd(xhci->shared_hcd, dev->irq,
-			IRQF_DISABLED | IRQF_SHARED);
+			IRQF_SHARED);
 	if (retval)
 		goto put_usb3_hcd;
 	/* Roothub already marked as USB 3.0 speed */
+
+	if (HCC_MAX_PSA(xhci->hcc_params) >= 4)
+		xhci->shared_hcd->can_do_streams = 1;
+
+	/* USB-2 and USB-3 roothubs initialized, allow runtime pm suspend */
+	pm_runtime_put_noidle(&dev->dev);
+
 	return 0;
 
 put_usb3_hcd:
 	usb_put_hcd(xhci->shared_hcd);
 dealloc_usb2_hcd:
 	usb_hcd_pci_remove(dev);
+put_runtime_pm:
+	pm_runtime_put_noidle(&dev->dev);
 	return retval;
 }
 
@@ -220,6 +257,11 @@ static void xhci_pci_remove(struct pci_dev *dev)
 		usb_put_hcd(xhci->shared_hcd);
 	}
 	usb_hcd_pci_remove(dev);
+
+	/* Workaround for spurious wakeups at shutdown with HSW */
+	if (xhci->quirks & XHCI_SPURIOUS_WAKEUP)
+		pci_set_power_state(dev, PCI_D3hot);
+
 	kfree(xhci);
 }
 
@@ -227,22 +269,45 @@ static void xhci_pci_remove(struct pci_dev *dev)
 static int xhci_pci_suspend(struct usb_hcd *hcd, bool do_wakeup)
 {
 	struct xhci_hcd	*xhci = hcd_to_xhci(hcd);
-	int	retval = 0;
-
-	if (hcd->state != HC_STATE_SUSPENDED ||
-			xhci->shared_hcd->state != HC_STATE_SUSPENDED)
-		return -EINVAL;
+	struct pci_dev		*pdev = to_pci_dev(hcd->self.controller);
 
-	retval = xhci_suspend(xhci);
+	/*
+	 * Systems with the TI redriver that loses port status change events
+	 * need to have the registers polled during D3, so avoid D3cold.
+	 */
+	if (xhci_compliance_mode_recovery_timer_quirk_check())
+		pdev->no_d3cold = true;
 
-	return retval;
+	return xhci_suspend(xhci);
 }
 
 static int xhci_pci_resume(struct usb_hcd *hcd, bool hibernated)
 {
 	struct xhci_hcd		*xhci = hcd_to_xhci(hcd);
+	struct pci_dev		*pdev = to_pci_dev(hcd->self.controller);
 	int			retval = 0;
 
+	/* The BIOS on systems with the Intel Panther Point chipset may or may
+	 * not support xHCI natively.  That means that during system resume, it
+	 * may switch the ports back to EHCI so that users can use their
+	 * keyboard to select a kernel from GRUB after resume from hibernate.
+	 *
+	 * The BIOS is supposed to remember whether the OS had xHCI ports
+	 * enabled before resume, and switch the ports back to xHCI when the
+	 * BIOS/OS semaphore is written, but we all know we can't trust BIOS
+	 * writers.
+	 *
+	 * Unconditionally switch the ports back to xHCI after a system resume.
+	 * It should not matter whether the EHCI or xHCI controller is
+	 * resumed first. It's enough to do the switchover in xHCI because
+	 * USB core won't notice anything as the hub driver doesn't start
+	 * running again until after all the devices (including both EHCI and
+	 * xHCI host controllers) have been resumed.
+	 */
+
+	if (pdev->vendor == PCI_VENDOR_ID_INTEL)
+		usb_enable_intel_xhci_ports(pdev);
+
 	retval = xhci_resume(xhci, hibernated);
 	return retval;
 }
@@ -286,6 +351,7 @@ static const struct hc_driver xhci_pci_hc_driver = {
 	.check_bandwidth =	xhci_check_bandwidth,
 	.reset_bandwidth =	xhci_reset_bandwidth,
 	.address_device =	xhci_address_device,
+	.enable_device =	xhci_enable_device,
 	.update_hub_device =	xhci_update_hub_device,
 	.reset_device =		xhci_discover_or_reset_device,
 
@@ -299,6 +365,14 @@ static const struct hc_driver xhci_pci_hc_driver = {
 	.hub_status_data =	xhci_hub_status_data,
 	.bus_suspend =		xhci_bus_suspend,
 	.bus_resume =		xhci_bus_resume,
+	/*
+	 * call back when device connected and addressed
+	 */
+	.update_device =        xhci_update_device,
+	.set_usb2_hw_lpm =	xhci_set_usb2_hardware_lpm,
+	.enable_usb3_lpm_timeout =	xhci_enable_usb3_lpm_timeout,
+	.disable_usb3_lpm_timeout =	xhci_disable_usb3_lpm_timeout,
+	.find_raw_port_number =	xhci_find_raw_port_number,
 };
 
 /*-------------------------------------------------------------------------*/
@@ -323,14 +397,14 @@ static struct pci_driver xhci_pci_driver = {
 	/* suspend and resume implemented later */
 
 	.shutdown = 	usb_hcd_pci_shutdown,
-#ifdef CONFIG_PM_SLEEP
+#ifdef CONFIG_PM
 	.driver = {
 		.pm = &usb_hcd_pci_pm_ops
 	},
 #endif
 };
 
-int xhci_register_pci(void)
+int __init xhci_register_pci(void)
 {
 	return pci_register_driver(&xhci_pci_driver);
 }