diff options
Diffstat (limited to 'drivers/usb/host/ehci-omap.c')
| -rw-r--r-- | drivers/usb/host/ehci-omap.c | 874 |
1 files changed, 177 insertions, 697 deletions
diff --git a/drivers/usb/host/ehci-omap.c b/drivers/usb/host/ehci-omap.c index 116ae280053..a24720beb39 100644 --- a/drivers/usb/host/ehci-omap.c +++ b/drivers/usb/host/ehci-omap.c @@ -1,11 +1,14 @@ /* - * ehci-omap.c - driver for USBHOST on OMAP 34xx processor + * ehci-omap.c - driver for USBHOST on OMAP3/4 processors * - * Bus Glue for OMAP34xx USBHOST 3 port EHCI controller - * Tested on OMAP3430 ES2.0 SDP + * Bus Glue for the EHCI controllers in OMAP3/4 + * Tested on several OMAP3 boards, and OMAP4 Pandaboard * - * Copyright (C) 2007-2008 Texas Instruments, Inc. + * Copyright (C) 2007-2013 Texas Instruments, Inc. * Author: Vikram Pandita <vikram.pandita@ti.com> + * Author: Anand Gadiyar <gadiyar@ti.com> + * Author: Keshava Munegowda <keshava_mgowda@ti.com> + * Author: Roger Quadros <rogerq@ti.com> * * Copyright (C) 2009 Nokia Corporation * Contact: Felipe Balbi <felipe.balbi@nokia.com> @@ -26,95 +29,25 @@ * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA * - * TODO (last updated Feb 12, 2010): - * - add kernel-doc - * - enable AUTOIDLE - * - add suspend/resume - * - move workarounds to board-files */ +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/io.h> #include <linux/platform_device.h> -#include <linux/clk.h> -#include <linux/gpio.h> -#include <linux/regulator/consumer.h> #include <linux/slab.h> #include <linux/usb/ulpi.h> -#include <plat/usb.h> +#include <linux/pm_runtime.h> +#include <linux/gpio.h> +#include <linux/clk.h> +#include <linux/usb.h> +#include <linux/usb/hcd.h> +#include <linux/of.h> +#include <linux/dma-mapping.h> -/* - * OMAP USBHOST Register addresses: VIRTUAL ADDRESSES - * Use ehci_omap_readl()/ehci_omap_writel() functions - */ +#include "ehci.h" -/* TLL Register Set */ -#define OMAP_USBTLL_REVISION (0x00) -#define OMAP_USBTLL_SYSCONFIG (0x10) -#define OMAP_USBTLL_SYSCONFIG_CACTIVITY (1 << 8) -#define OMAP_USBTLL_SYSCONFIG_SIDLEMODE (1 << 3) -#define OMAP_USBTLL_SYSCONFIG_ENAWAKEUP (1 << 2) -#define OMAP_USBTLL_SYSCONFIG_SOFTRESET (1 << 1) -#define OMAP_USBTLL_SYSCONFIG_AUTOIDLE (1 << 0) - -#define OMAP_USBTLL_SYSSTATUS (0x14) -#define OMAP_USBTLL_SYSSTATUS_RESETDONE (1 << 0) - -#define OMAP_USBTLL_IRQSTATUS (0x18) -#define OMAP_USBTLL_IRQENABLE (0x1C) - -#define OMAP_TLL_SHARED_CONF (0x30) -#define OMAP_TLL_SHARED_CONF_USB_90D_DDR_EN (1 << 6) -#define OMAP_TLL_SHARED_CONF_USB_180D_SDR_EN (1 << 5) -#define OMAP_TLL_SHARED_CONF_USB_DIVRATION (1 << 2) -#define OMAP_TLL_SHARED_CONF_FCLK_REQ (1 << 1) -#define OMAP_TLL_SHARED_CONF_FCLK_IS_ON (1 << 0) - -#define OMAP_TLL_CHANNEL_CONF(num) (0x040 + 0x004 * num) -#define OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF (1 << 11) -#define OMAP_TLL_CHANNEL_CONF_ULPI_ULPIAUTOIDLE (1 << 10) -#define OMAP_TLL_CHANNEL_CONF_UTMIAUTOIDLE (1 << 9) -#define OMAP_TLL_CHANNEL_CONF_ULPIDDRMODE (1 << 8) -#define OMAP_TLL_CHANNEL_CONF_CHANEN (1 << 0) - -#define OMAP_TLL_ULPI_FUNCTION_CTRL(num) (0x804 + 0x100 * num) -#define OMAP_TLL_ULPI_INTERFACE_CTRL(num) (0x807 + 0x100 * num) -#define OMAP_TLL_ULPI_OTG_CTRL(num) (0x80A + 0x100 * num) -#define OMAP_TLL_ULPI_INT_EN_RISE(num) (0x80D + 0x100 * num) -#define OMAP_TLL_ULPI_INT_EN_FALL(num) (0x810 + 0x100 * num) -#define OMAP_TLL_ULPI_INT_STATUS(num) (0x813 + 0x100 * num) -#define OMAP_TLL_ULPI_INT_LATCH(num) (0x814 + 0x100 * num) -#define OMAP_TLL_ULPI_DEBUG(num) (0x815 + 0x100 * num) -#define OMAP_TLL_ULPI_SCRATCH_REGISTER(num) (0x816 + 0x100 * num) - -#define OMAP_TLL_CHANNEL_COUNT 3 -#define OMAP_TLL_CHANNEL_1_EN_MASK (1 << 1) -#define OMAP_TLL_CHANNEL_2_EN_MASK (1 << 2) -#define OMAP_TLL_CHANNEL_3_EN_MASK (1 << 4) - -/* UHH Register Set */ -#define OMAP_UHH_REVISION (0x00) -#define OMAP_UHH_SYSCONFIG (0x10) -#define OMAP_UHH_SYSCONFIG_MIDLEMODE (1 << 12) -#define OMAP_UHH_SYSCONFIG_CACTIVITY (1 << 8) -#define OMAP_UHH_SYSCONFIG_SIDLEMODE (1 << 3) -#define OMAP_UHH_SYSCONFIG_ENAWAKEUP (1 << 2) -#define OMAP_UHH_SYSCONFIG_SOFTRESET (1 << 1) -#define OMAP_UHH_SYSCONFIG_AUTOIDLE (1 << 0) - -#define OMAP_UHH_SYSSTATUS (0x14) -#define OMAP_UHH_HOSTCONFIG (0x40) -#define OMAP_UHH_HOSTCONFIG_ULPI_BYPASS (1 << 0) -#define OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS (1 << 0) -#define OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS (1 << 11) -#define OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS (1 << 12) -#define OMAP_UHH_HOSTCONFIG_INCR4_BURST_EN (1 << 2) -#define OMAP_UHH_HOSTCONFIG_INCR8_BURST_EN (1 << 3) -#define OMAP_UHH_HOSTCONFIG_INCR16_BURST_EN (1 << 4) -#define OMAP_UHH_HOSTCONFIG_INCRX_ALIGN_EN (1 << 5) -#define OMAP_UHH_HOSTCONFIG_P1_CONNECT_STATUS (1 << 8) -#define OMAP_UHH_HOSTCONFIG_P2_CONNECT_STATUS (1 << 9) -#define OMAP_UHH_HOSTCONFIG_P3_CONNECT_STATUS (1 << 10) - -#define OMAP_UHH_DEBUG_CSR (0x44) +#include <linux/platform_data/usb-omap.h> /* EHCI Register Set */ #define EHCI_INSNREG04 (0xA0) @@ -127,292 +60,143 @@ #define EHCI_INSNREG05_ULPI_EXTREGADD_SHIFT 8 #define EHCI_INSNREG05_ULPI_WRDATA_SHIFT 0 +#define DRIVER_DESC "OMAP-EHCI Host Controller driver" + +static const char hcd_name[] = "ehci-omap"; + /*-------------------------------------------------------------------------*/ -static inline void ehci_omap_writel(void __iomem *base, u32 reg, u32 val) +struct omap_hcd { + struct usb_phy *phy[OMAP3_HS_USB_PORTS]; /* one PHY for each port */ + int nports; +}; + +static inline void ehci_write(void __iomem *base, u32 reg, u32 val) { __raw_writel(val, base + reg); } -static inline u32 ehci_omap_readl(void __iomem *base, u32 reg) +static inline u32 ehci_read(void __iomem *base, u32 reg) { return __raw_readl(base + reg); } -static inline void ehci_omap_writeb(void __iomem *base, u8 reg, u8 val) -{ - __raw_writeb(val, base + reg); -} - -static inline u8 ehci_omap_readb(void __iomem *base, u8 reg) -{ - return __raw_readb(base + reg); -} - -/*-------------------------------------------------------------------------*/ - -struct ehci_hcd_omap { - struct ehci_hcd *ehci; - struct device *dev; - - struct clk *usbhost_ick; - struct clk *usbhost2_120m_fck; - struct clk *usbhost1_48m_fck; - struct clk *usbtll_fck; - struct clk *usbtll_ick; - - /* FIXME the following two workarounds are - * board specific not silicon-specific so these - * should be moved to board-file instead. - * - * Maybe someone from TI will know better which - * board is affected and needs the workarounds - * to be applied - */ - - /* gpio for resetting phy */ - int reset_gpio_port[OMAP3_HS_USB_PORTS]; - - /* phy reset workaround */ - int phy_reset; - - /* desired phy_mode: TLL, PHY */ - enum ehci_hcd_omap_mode port_mode[OMAP3_HS_USB_PORTS]; +/* configure so an HC device and id are always provided */ +/* always called with process context; sleeping is OK */ - void __iomem *uhh_base; - void __iomem *tll_base; - void __iomem *ehci_base; +static struct hc_driver __read_mostly ehci_omap_hc_driver; - /* Regulators for USB PHYs. - * Each PHY can have a separate regulator. - */ - struct regulator *regulator[OMAP3_HS_USB_PORTS]; +static const struct ehci_driver_overrides ehci_omap_overrides __initdata = { + .extra_priv_size = sizeof(struct omap_hcd), }; -/*-------------------------------------------------------------------------*/ - -static void omap_usb_utmi_init(struct ehci_hcd_omap *omap, u8 tll_channel_mask) +/** + * ehci_hcd_omap_probe - initialize TI-based HCDs + * + * Allocates basic resources for this USB host controller, and + * then invokes the start() method for the HCD associated with it + * through the hotplug entry's driver_data. + */ +static int ehci_hcd_omap_probe(struct platform_device *pdev) { - unsigned reg; + struct device *dev = &pdev->dev; + struct usbhs_omap_platform_data *pdata = dev_get_platdata(dev); + struct resource *res; + struct usb_hcd *hcd; + void __iomem *regs; + int ret; + int irq; int i; + struct omap_hcd *omap; - /* Program the 3 TLL channels upfront */ - for (i = 0; i < OMAP_TLL_CHANNEL_COUNT; i++) { - reg = ehci_omap_readl(omap->tll_base, OMAP_TLL_CHANNEL_CONF(i)); - - /* Disable AutoIdle, BitStuffing and use SDR Mode */ - reg &= ~(OMAP_TLL_CHANNEL_CONF_UTMIAUTOIDLE - | OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF - | OMAP_TLL_CHANNEL_CONF_ULPIDDRMODE); - ehci_omap_writel(omap->tll_base, OMAP_TLL_CHANNEL_CONF(i), reg); - } - - /* Program Common TLL register */ - reg = ehci_omap_readl(omap->tll_base, OMAP_TLL_SHARED_CONF); - reg |= (OMAP_TLL_SHARED_CONF_FCLK_IS_ON - | OMAP_TLL_SHARED_CONF_USB_DIVRATION - | OMAP_TLL_SHARED_CONF_USB_180D_SDR_EN); - reg &= ~OMAP_TLL_SHARED_CONF_USB_90D_DDR_EN; - - ehci_omap_writel(omap->tll_base, OMAP_TLL_SHARED_CONF, reg); - - /* Enable channels now */ - for (i = 0; i < OMAP_TLL_CHANNEL_COUNT; i++) { - reg = ehci_omap_readl(omap->tll_base, OMAP_TLL_CHANNEL_CONF(i)); - - /* Enable only the reg that is needed */ - if (!(tll_channel_mask & 1<<i)) - continue; - - reg |= OMAP_TLL_CHANNEL_CONF_CHANEN; - ehci_omap_writel(omap->tll_base, OMAP_TLL_CHANNEL_CONF(i), reg); + if (usb_disabled()) + return -ENODEV; - ehci_omap_writeb(omap->tll_base, - OMAP_TLL_ULPI_SCRATCH_REGISTER(i), 0xbe); - dev_dbg(omap->dev, "ULPI_SCRATCH_REG[ch=%d]= 0x%02x\n", - i+1, ehci_omap_readb(omap->tll_base, - OMAP_TLL_ULPI_SCRATCH_REGISTER(i))); + if (!dev->parent) { + dev_err(dev, "Missing parent device\n"); + return -ENODEV; } -} - -/*-------------------------------------------------------------------------*/ -static void omap_ehci_soft_phy_reset(struct ehci_hcd_omap *omap, u8 port) -{ - unsigned long timeout = jiffies + msecs_to_jiffies(1000); - unsigned reg = 0; - - reg = ULPI_FUNC_CTRL_RESET - /* FUNCTION_CTRL_SET register */ - | (ULPI_SET(ULPI_FUNC_CTRL) << EHCI_INSNREG05_ULPI_REGADD_SHIFT) - /* Write */ - | (2 << EHCI_INSNREG05_ULPI_OPSEL_SHIFT) - /* PORTn */ - | ((port + 1) << EHCI_INSNREG05_ULPI_PORTSEL_SHIFT) - /* start ULPI access*/ - | (1 << EHCI_INSNREG05_ULPI_CONTROL_SHIFT); - - ehci_omap_writel(omap->ehci_base, EHCI_INSNREG05_ULPI, reg); - - /* Wait for ULPI access completion */ - while ((ehci_omap_readl(omap->ehci_base, EHCI_INSNREG05_ULPI) - & (1 << EHCI_INSNREG05_ULPI_CONTROL_SHIFT))) { - cpu_relax(); - - if (time_after(jiffies, timeout)) { - dev_dbg(omap->dev, "phy reset operation timed out\n"); - break; - } + /* For DT boot, get platform data from parent. i.e. usbhshost */ + if (dev->of_node) { + pdata = dev_get_platdata(dev->parent); + dev->platform_data = pdata; } -} -/* omap_start_ehc - * - Start the TI USBHOST controller - */ -static int omap_start_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd) -{ - unsigned long timeout = jiffies + msecs_to_jiffies(1000); - u8 tll_ch_mask = 0; - unsigned reg = 0; - int ret = 0; - - dev_dbg(omap->dev, "starting TI EHCI USB Controller\n"); - - /* Enable Clocks for USBHOST */ - omap->usbhost_ick = clk_get(omap->dev, "usbhost_ick"); - if (IS_ERR(omap->usbhost_ick)) { - ret = PTR_ERR(omap->usbhost_ick); - goto err_host_ick; + if (!pdata) { + dev_err(dev, "Missing platform data\n"); + return -ENODEV; } - clk_enable(omap->usbhost_ick); - omap->usbhost2_120m_fck = clk_get(omap->dev, "usbhost_120m_fck"); - if (IS_ERR(omap->usbhost2_120m_fck)) { - ret = PTR_ERR(omap->usbhost2_120m_fck); - goto err_host_120m_fck; + irq = platform_get_irq(pdev, 0); + if (irq < 0) { + dev_err(dev, "EHCI irq failed\n"); + return -ENODEV; } - clk_enable(omap->usbhost2_120m_fck); - omap->usbhost1_48m_fck = clk_get(omap->dev, "usbhost_48m_fck"); - if (IS_ERR(omap->usbhost1_48m_fck)) { - ret = PTR_ERR(omap->usbhost1_48m_fck); - goto err_host_48m_fck; - } - clk_enable(omap->usbhost1_48m_fck); - - if (omap->phy_reset) { - /* Refer: ISSUE1 */ - if (gpio_is_valid(omap->reset_gpio_port[0])) { - gpio_request(omap->reset_gpio_port[0], - "USB1 PHY reset"); - gpio_direction_output(omap->reset_gpio_port[0], 0); - } + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + regs = devm_ioremap_resource(dev, res); + if (IS_ERR(regs)) + return PTR_ERR(regs); - if (gpio_is_valid(omap->reset_gpio_port[1])) { - gpio_request(omap->reset_gpio_port[1], - "USB2 PHY reset"); - gpio_direction_output(omap->reset_gpio_port[1], 0); - } + /* + * Right now device-tree probed devices don't get dma_mask set. + * Since shared usb code relies on it, set it here for now. + * Once we have dma capability bindings this can go away. + */ + ret = dma_coerce_mask_and_coherent(dev, DMA_BIT_MASK(32)); + if (ret) + return ret; - /* Hold the PHY in RESET for enough time till DIR is high */ - udelay(10); + ret = -ENODEV; + hcd = usb_create_hcd(&ehci_omap_hc_driver, dev, + dev_name(dev)); + if (!hcd) { + dev_err(dev, "Failed to create HCD\n"); + return -ENOMEM; } - /* Configure TLL for 60Mhz clk for ULPI */ - omap->usbtll_fck = clk_get(omap->dev, "usbtll_fck"); - if (IS_ERR(omap->usbtll_fck)) { - ret = PTR_ERR(omap->usbtll_fck); - goto err_tll_fck; - } - clk_enable(omap->usbtll_fck); + hcd->rsrc_start = res->start; + hcd->rsrc_len = resource_size(res); + hcd->regs = regs; + hcd_to_ehci(hcd)->caps = regs; - omap->usbtll_ick = clk_get(omap->dev, "usbtll_ick"); - if (IS_ERR(omap->usbtll_ick)) { - ret = PTR_ERR(omap->usbtll_ick); - goto err_tll_ick; - } - clk_enable(omap->usbtll_ick); + omap = (struct omap_hcd *)hcd_to_ehci(hcd)->priv; + omap->nports = pdata->nports; - /* perform TLL soft reset, and wait until reset is complete */ - ehci_omap_writel(omap->tll_base, OMAP_USBTLL_SYSCONFIG, - OMAP_USBTLL_SYSCONFIG_SOFTRESET); + platform_set_drvdata(pdev, hcd); - /* Wait for TLL reset to complete */ - while (!(ehci_omap_readl(omap->tll_base, OMAP_USBTLL_SYSSTATUS) - & OMAP_USBTLL_SYSSTATUS_RESETDONE)) { - cpu_relax(); + /* get the PHY devices if needed */ + for (i = 0 ; i < omap->nports ; i++) { + struct usb_phy *phy; - if (time_after(jiffies, timeout)) { - dev_dbg(omap->dev, "operation timed out\n"); - ret = -EINVAL; - goto err_sys_status; + /* get the PHY device */ + if (dev->of_node) + phy = devm_usb_get_phy_by_phandle(dev, "phys", i); + else + phy = devm_usb_get_phy_dev(dev, i); + if (IS_ERR(phy)) { + /* Don't bail out if PHY is not absolutely necessary */ + if (pdata->port_mode[i] != OMAP_EHCI_PORT_MODE_PHY) + continue; + + ret = PTR_ERR(phy); + dev_err(dev, "Can't get PHY device for port %d: %d\n", + i, ret); + goto err_phy; } - } - dev_dbg(omap->dev, "TLL RESET DONE\n"); - - /* (1<<3) = no idle mode only for initial debugging */ - ehci_omap_writel(omap->tll_base, OMAP_USBTLL_SYSCONFIG, - OMAP_USBTLL_SYSCONFIG_ENAWAKEUP | - OMAP_USBTLL_SYSCONFIG_SIDLEMODE | - OMAP_USBTLL_SYSCONFIG_CACTIVITY); - - - /* Put UHH in NoIdle/NoStandby mode */ - reg = ehci_omap_readl(omap->uhh_base, OMAP_UHH_SYSCONFIG); - reg |= (OMAP_UHH_SYSCONFIG_ENAWAKEUP - | OMAP_UHH_SYSCONFIG_SIDLEMODE - | OMAP_UHH_SYSCONFIG_CACTIVITY - | OMAP_UHH_SYSCONFIG_MIDLEMODE); - reg &= ~OMAP_UHH_SYSCONFIG_AUTOIDLE; - - ehci_omap_writel(omap->uhh_base, OMAP_UHH_SYSCONFIG, reg); - - reg = ehci_omap_readl(omap->uhh_base, OMAP_UHH_HOSTCONFIG); - - /* setup ULPI bypass and burst configurations */ - reg |= (OMAP_UHH_HOSTCONFIG_INCR4_BURST_EN - | OMAP_UHH_HOSTCONFIG_INCR8_BURST_EN - | OMAP_UHH_HOSTCONFIG_INCR16_BURST_EN); - reg &= ~OMAP_UHH_HOSTCONFIG_INCRX_ALIGN_EN; - - if (omap->port_mode[0] == EHCI_HCD_OMAP_MODE_UNKNOWN) - reg &= ~OMAP_UHH_HOSTCONFIG_P1_CONNECT_STATUS; - if (omap->port_mode[1] == EHCI_HCD_OMAP_MODE_UNKNOWN) - reg &= ~OMAP_UHH_HOSTCONFIG_P2_CONNECT_STATUS; - if (omap->port_mode[2] == EHCI_HCD_OMAP_MODE_UNKNOWN) - reg &= ~OMAP_UHH_HOSTCONFIG_P3_CONNECT_STATUS; - - /* Bypass the TLL module for PHY mode operation */ - if (cpu_is_omap3430() && (omap_rev() <= OMAP3430_REV_ES2_1)) { - dev_dbg(omap->dev, "OMAP3 ES version <= ES2.1\n"); - if ((omap->port_mode[0] == EHCI_HCD_OMAP_MODE_PHY) || - (omap->port_mode[1] == EHCI_HCD_OMAP_MODE_PHY) || - (omap->port_mode[2] == EHCI_HCD_OMAP_MODE_PHY)) - reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_BYPASS; - else - reg |= OMAP_UHH_HOSTCONFIG_ULPI_BYPASS; - } else { - dev_dbg(omap->dev, "OMAP3 ES version > ES2.1\n"); - if (omap->port_mode[0] == EHCI_HCD_OMAP_MODE_PHY) - reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS; - else if (omap->port_mode[0] == EHCI_HCD_OMAP_MODE_TLL) - reg |= OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS; - - if (omap->port_mode[1] == EHCI_HCD_OMAP_MODE_PHY) - reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS; - else if (omap->port_mode[1] == EHCI_HCD_OMAP_MODE_TLL) - reg |= OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS; - - if (omap->port_mode[2] == EHCI_HCD_OMAP_MODE_PHY) - reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS; - else if (omap->port_mode[2] == EHCI_HCD_OMAP_MODE_TLL) - reg |= OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS; + omap->phy[i] = phy; + if (pdata->port_mode[i] == OMAP_EHCI_PORT_MODE_PHY) { + usb_phy_init(omap->phy[i]); + /* bring PHY out of suspend */ + usb_phy_set_suspend(omap->phy[i], 0); + } } - ehci_omap_writel(omap->uhh_base, OMAP_UHH_HOSTCONFIG, reg); - dev_dbg(omap->dev, "UHH setup done, uhh_hostconfig=%x\n", reg); + pm_runtime_enable(dev); + pm_runtime_get_sync(dev); /* * An undocumented "feature" in the OMAP3 EHCI controller, @@ -423,327 +207,48 @@ static int omap_start_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd) * to suspend. Writing 1 to this undocumented register bit * disables this feature and restores normal behavior. */ - ehci_omap_writel(omap->ehci_base, EHCI_INSNREG04, + ehci_write(regs, EHCI_INSNREG04, EHCI_INSNREG04_DISABLE_UNSUSPEND); - if ((omap->port_mode[0] == EHCI_HCD_OMAP_MODE_TLL) || - (omap->port_mode[1] == EHCI_HCD_OMAP_MODE_TLL) || - (omap->port_mode[2] == EHCI_HCD_OMAP_MODE_TLL)) { - - if (omap->port_mode[0] == EHCI_HCD_OMAP_MODE_TLL) - tll_ch_mask |= OMAP_TLL_CHANNEL_1_EN_MASK; - if (omap->port_mode[1] == EHCI_HCD_OMAP_MODE_TLL) - tll_ch_mask |= OMAP_TLL_CHANNEL_2_EN_MASK; - if (omap->port_mode[2] == EHCI_HCD_OMAP_MODE_TLL) - tll_ch_mask |= OMAP_TLL_CHANNEL_3_EN_MASK; - - /* Enable UTMI mode for required TLL channels */ - omap_usb_utmi_init(omap, tll_ch_mask); - } - - if (omap->phy_reset) { - /* Refer ISSUE1: - * Hold the PHY in RESET for enough time till - * PHY is settled and ready - */ - udelay(10); - - if (gpio_is_valid(omap->reset_gpio_port[0])) - gpio_set_value(omap->reset_gpio_port[0], 1); - - if (gpio_is_valid(omap->reset_gpio_port[1])) - gpio_set_value(omap->reset_gpio_port[1], 1); - } - - /* Soft reset the PHY using PHY reset command over ULPI */ - if (omap->port_mode[0] == EHCI_HCD_OMAP_MODE_PHY) - omap_ehci_soft_phy_reset(omap, 0); - if (omap->port_mode[1] == EHCI_HCD_OMAP_MODE_PHY) - omap_ehci_soft_phy_reset(omap, 1); - - return 0; - -err_sys_status: - clk_disable(omap->usbtll_ick); - clk_put(omap->usbtll_ick); - -err_tll_ick: - clk_disable(omap->usbtll_fck); - clk_put(omap->usbtll_fck); - -err_tll_fck: - clk_disable(omap->usbhost1_48m_fck); - clk_put(omap->usbhost1_48m_fck); - - if (omap->phy_reset) { - if (gpio_is_valid(omap->reset_gpio_port[0])) - gpio_free(omap->reset_gpio_port[0]); - - if (gpio_is_valid(omap->reset_gpio_port[1])) - gpio_free(omap->reset_gpio_port[1]); - } - -err_host_48m_fck: - clk_disable(omap->usbhost2_120m_fck); - clk_put(omap->usbhost2_120m_fck); - -err_host_120m_fck: - clk_disable(omap->usbhost_ick); - clk_put(omap->usbhost_ick); - -err_host_ick: - return ret; -} - -static void omap_stop_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd) -{ - unsigned long timeout = jiffies + msecs_to_jiffies(100); - - dev_dbg(omap->dev, "stopping TI EHCI USB Controller\n"); - - /* Reset OMAP modules for insmod/rmmod to work */ - ehci_omap_writel(omap->uhh_base, OMAP_UHH_SYSCONFIG, - OMAP_UHH_SYSCONFIG_SOFTRESET); - while (!(ehci_omap_readl(omap->uhh_base, OMAP_UHH_SYSSTATUS) - & (1 << 0))) { - cpu_relax(); - - if (time_after(jiffies, timeout)) - dev_dbg(omap->dev, "operation timed out\n"); - } - - while (!(ehci_omap_readl(omap->uhh_base, OMAP_UHH_SYSSTATUS) - & (1 << 1))) { - cpu_relax(); - - if (time_after(jiffies, timeout)) - dev_dbg(omap->dev, "operation timed out\n"); - } - - while (!(ehci_omap_readl(omap->uhh_base, OMAP_UHH_SYSSTATUS) - & (1 << 2))) { - cpu_relax(); - - if (time_after(jiffies, timeout)) - dev_dbg(omap->dev, "operation timed out\n"); - } - - ehci_omap_writel(omap->tll_base, OMAP_USBTLL_SYSCONFIG, (1 << 1)); - - while (!(ehci_omap_readl(omap->tll_base, OMAP_USBTLL_SYSSTATUS) - & (1 << 0))) { - cpu_relax(); - - if (time_after(jiffies, timeout)) - dev_dbg(omap->dev, "operation timed out\n"); - } - - if (omap->usbtll_fck != NULL) { - clk_disable(omap->usbtll_fck); - clk_put(omap->usbtll_fck); - omap->usbtll_fck = NULL; - } - - if (omap->usbhost_ick != NULL) { - clk_disable(omap->usbhost_ick); - clk_put(omap->usbhost_ick); - omap->usbhost_ick = NULL; - } - - if (omap->usbhost1_48m_fck != NULL) { - clk_disable(omap->usbhost1_48m_fck); - clk_put(omap->usbhost1_48m_fck); - omap->usbhost1_48m_fck = NULL; - } - - if (omap->usbhost2_120m_fck != NULL) { - clk_disable(omap->usbhost2_120m_fck); - clk_put(omap->usbhost2_120m_fck); - omap->usbhost2_120m_fck = NULL; - } - - if (omap->usbtll_ick != NULL) { - clk_disable(omap->usbtll_ick); - clk_put(omap->usbtll_ick); - omap->usbtll_ick = NULL; - } - - if (omap->phy_reset) { - if (gpio_is_valid(omap->reset_gpio_port[0])) - gpio_free(omap->reset_gpio_port[0]); - - if (gpio_is_valid(omap->reset_gpio_port[1])) - gpio_free(omap->reset_gpio_port[1]); - } - - dev_dbg(omap->dev, "Clock to USB host has been disabled\n"); -} - -/*-------------------------------------------------------------------------*/ - -static const struct hc_driver ehci_omap_hc_driver; - -/* configure so an HC device and id are always provided */ -/* always called with process context; sleeping is OK */ - -/** - * ehci_hcd_omap_probe - initialize TI-based HCDs - * - * Allocates basic resources for this USB host controller, and - * then invokes the start() method for the HCD associated with it - * through the hotplug entry's driver_data. - */ -static int ehci_hcd_omap_probe(struct platform_device *pdev) -{ - struct ehci_hcd_omap_platform_data *pdata = pdev->dev.platform_data; - struct ehci_hcd_omap *omap; - struct resource *res; - struct usb_hcd *hcd; - - int irq = platform_get_irq(pdev, 0); - int ret = -ENODEV; - int i; - char supply[7]; - - if (!pdata) { - dev_dbg(&pdev->dev, "missing platform_data\n"); - goto err_pdata; - } - - if (usb_disabled()) - goto err_disabled; - - omap = kzalloc(sizeof(*omap), GFP_KERNEL); - if (!omap) { - ret = -ENOMEM; - goto err_disabled; - } - - hcd = usb_create_hcd(&ehci_omap_hc_driver, &pdev->dev, - dev_name(&pdev->dev)); - if (!hcd) { - dev_dbg(&pdev->dev, "failed to create hcd with err %d\n", ret); - ret = -ENOMEM; - goto err_create_hcd; - } - - platform_set_drvdata(pdev, omap); - omap->dev = &pdev->dev; - omap->phy_reset = pdata->phy_reset; - omap->reset_gpio_port[0] = pdata->reset_gpio_port[0]; - omap->reset_gpio_port[1] = pdata->reset_gpio_port[1]; - omap->reset_gpio_port[2] = pdata->reset_gpio_port[2]; - omap->port_mode[0] = pdata->port_mode[0]; - omap->port_mode[1] = pdata->port_mode[1]; - omap->port_mode[2] = pdata->port_mode[2]; - omap->ehci = hcd_to_ehci(hcd); - omap->ehci->sbrn = 0x20; - - res = platform_get_resource(pdev, IORESOURCE_MEM, 0); - - hcd->rsrc_start = res->start; - hcd->rsrc_len = resource_size(res); - - hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len); - if (!hcd->regs) { - dev_err(&pdev->dev, "EHCI ioremap failed\n"); - ret = -ENOMEM; - goto err_ioremap; - } - - /* we know this is the memory we want, no need to ioremap again */ - omap->ehci->caps = hcd->regs; - omap->ehci_base = hcd->regs; - - res = platform_get_resource(pdev, IORESOURCE_MEM, 1); - omap->uhh_base = ioremap(res->start, resource_size(res)); - if (!omap->uhh_base) { - dev_err(&pdev->dev, "UHH ioremap failed\n"); - ret = -ENOMEM; - goto err_uhh_ioremap; - } - - res = platform_get_resource(pdev, IORESOURCE_MEM, 2); - omap->tll_base = ioremap(res->start, resource_size(res)); - if (!omap->tll_base) { - dev_err(&pdev->dev, "TLL ioremap failed\n"); - ret = -ENOMEM; - goto err_tll_ioremap; - } - - /* get ehci regulator and enable */ - for (i = 0 ; i < OMAP3_HS_USB_PORTS ; i++) { - if (omap->port_mode[i] != EHCI_HCD_OMAP_MODE_PHY) { - omap->regulator[i] = NULL; - continue; - } - snprintf(supply, sizeof(supply), "hsusb%d", i); - omap->regulator[i] = regulator_get(omap->dev, supply); - if (IS_ERR(omap->regulator[i])) { - omap->regulator[i] = NULL; - dev_dbg(&pdev->dev, - "failed to get ehci port%d regulator\n", i); - } else { - regulator_enable(omap->regulator[i]); - } - } - - ret = omap_start_ehc(omap, hcd); + ret = usb_add_hcd(hcd, irq, IRQF_SHARED); if (ret) { - dev_dbg(&pdev->dev, "failed to start ehci\n"); - goto err_start; + dev_err(dev, "failed to add hcd with err %d\n", ret); + goto err_pm_runtime; } + device_wakeup_enable(hcd->self.controller); - omap->ehci->regs = hcd->regs - + HC_LENGTH(readl(&omap->ehci->caps->hc_capbase)); - - dbg_hcs_params(omap->ehci, "reset"); - dbg_hcc_params(omap->ehci, "reset"); - - /* cache this readonly data; minimize chip reads */ - omap->ehci->hcs_params = readl(&omap->ehci->caps->hcs_params); + /* + * Bring PHYs out of reset for non PHY modes. + * Even though HSIC mode is a PHY-less mode, the reset + * line exists between the chips and can be modelled + * as a PHY device for reset control. + */ + for (i = 0; i < omap->nports; i++) { + if (!omap->phy[i] || + pdata->port_mode[i] == OMAP_EHCI_PORT_MODE_PHY) + continue; - ret = usb_add_hcd(hcd, irq, IRQF_DISABLED | IRQF_SHARED); - if (ret) { - dev_dbg(&pdev->dev, "failed to add hcd with err %d\n", ret); - goto err_add_hcd; + usb_phy_init(omap->phy[i]); + /* bring PHY out of suspend */ + usb_phy_set_suspend(omap->phy[i], 0); } - /* root ports should always stay powered */ - ehci_port_power(omap->ehci, 1); - return 0; -err_add_hcd: - omap_stop_ehc(omap, hcd); +err_pm_runtime: + pm_runtime_put_sync(dev); -err_start: - for (i = 0 ; i < OMAP3_HS_USB_PORTS ; i++) { - if (omap->regulator[i]) { - regulator_disable(omap->regulator[i]); - regulator_put(omap->regulator[i]); - } +err_phy: + for (i = 0; i < omap->nports; i++) { + if (omap->phy[i]) + usb_phy_shutdown(omap->phy[i]); } - iounmap(omap->tll_base); - -err_tll_ioremap: - iounmap(omap->uhh_base); - -err_uhh_ioremap: - iounmap(hcd->regs); -err_ioremap: usb_put_hcd(hcd); -err_create_hcd: - kfree(omap); -err_disabled: -err_pdata: return ret; } -/* may be called without controller electrically present */ -/* may be called with controller, bus, and devices active */ /** * ehci_hcd_omap_remove - shutdown processing for EHCI HCDs @@ -755,93 +260,68 @@ err_pdata: */ static int ehci_hcd_omap_remove(struct platform_device *pdev) { - struct ehci_hcd_omap *omap = platform_get_drvdata(pdev); - struct usb_hcd *hcd = ehci_to_hcd(omap->ehci); + struct device *dev = &pdev->dev; + struct usb_hcd *hcd = dev_get_drvdata(dev); + struct omap_hcd *omap = (struct omap_hcd *)hcd_to_ehci(hcd)->priv; int i; usb_remove_hcd(hcd); - omap_stop_ehc(omap, hcd); - iounmap(hcd->regs); - for (i = 0 ; i < OMAP3_HS_USB_PORTS ; i++) { - if (omap->regulator[i]) { - regulator_disable(omap->regulator[i]); - regulator_put(omap->regulator[i]); - } + + for (i = 0; i < omap->nports; i++) { + if (omap->phy[i]) + usb_phy_shutdown(omap->phy[i]); } - iounmap(omap->tll_base); - iounmap(omap->uhh_base); + usb_put_hcd(hcd); - kfree(omap); + pm_runtime_put_sync(dev); + pm_runtime_disable(dev); return 0; } -static void ehci_hcd_omap_shutdown(struct platform_device *pdev) -{ - struct ehci_hcd_omap *omap = platform_get_drvdata(pdev); - struct usb_hcd *hcd = ehci_to_hcd(omap->ehci); +static const struct of_device_id omap_ehci_dt_ids[] = { + { .compatible = "ti,ehci-omap" }, + { } +}; - if (hcd->driver->shutdown) - hcd->driver->shutdown(hcd); -} +MODULE_DEVICE_TABLE(of, omap_ehci_dt_ids); static struct platform_driver ehci_hcd_omap_driver = { .probe = ehci_hcd_omap_probe, .remove = ehci_hcd_omap_remove, - .shutdown = ehci_hcd_omap_shutdown, + .shutdown = usb_hcd_platform_shutdown, /*.suspend = ehci_hcd_omap_suspend, */ /*.resume = ehci_hcd_omap_resume, */ .driver = { - .name = "ehci-omap", + .name = hcd_name, + .of_match_table = omap_ehci_dt_ids, } }; /*-------------------------------------------------------------------------*/ -static const struct hc_driver ehci_omap_hc_driver = { - .description = hcd_name, - .product_desc = "OMAP-EHCI Host Controller", - .hcd_priv_size = sizeof(struct ehci_hcd), - - /* - * generic hardware linkage - */ - .irq = ehci_irq, - .flags = HCD_MEMORY | HCD_USB2, - - /* - * basic lifecycle operations - */ - .reset = ehci_init, - .start = ehci_run, - .stop = ehci_stop, - .shutdown = ehci_shutdown, - - /* - * managing i/o requests and associated device resources - */ - .urb_enqueue = ehci_urb_enqueue, - .urb_dequeue = ehci_urb_dequeue, - .endpoint_disable = ehci_endpoint_disable, - .endpoint_reset = ehci_endpoint_reset, +static int __init ehci_omap_init(void) +{ + if (usb_disabled()) + return -ENODEV; - /* - * scheduling support - */ - .get_frame_number = ehci_get_frame, + pr_info("%s: " DRIVER_DESC "\n", hcd_name); - /* - * root hub support - */ - .hub_status_data = ehci_hub_status_data, - .hub_control = ehci_hub_control, - .bus_suspend = ehci_bus_suspend, - .bus_resume = ehci_bus_resume, + ehci_init_driver(&ehci_omap_hc_driver, &ehci_omap_overrides); + return platform_driver_register(&ehci_hcd_omap_driver); +} +module_init(ehci_omap_init); - .clear_tt_buffer_complete = ehci_clear_tt_buffer_complete, -}; +static void __exit ehci_omap_cleanup(void) +{ + platform_driver_unregister(&ehci_hcd_omap_driver); +} +module_exit(ehci_omap_cleanup); -MODULE_ALIAS("platform:omap-ehci"); +MODULE_ALIAS("platform:ehci-omap"); MODULE_AUTHOR("Texas Instruments, Inc."); MODULE_AUTHOR("Felipe Balbi <felipe.balbi@nokia.com>"); +MODULE_AUTHOR("Roger Quadros <rogerq@ti.com>"); +MODULE_DESCRIPTION(DRIVER_DESC); +MODULE_LICENSE("GPL"); |