diff options
Diffstat (limited to 'drivers/usb/host/ehci-msm.c')
| -rw-r--r-- | drivers/usb/host/ehci-msm.c | 253 |
1 files changed, 70 insertions, 183 deletions
diff --git a/drivers/usb/host/ehci-msm.c b/drivers/usb/host/ehci-msm.c index 413f4deca53..982c09bebe0 100644 --- a/drivers/usb/host/ehci-msm.c +++ b/drivers/usb/host/ehci-msm.c @@ -1,6 +1,6 @@ /* ehci-msm.c - HSUSB Host Controller Driver Implementation * - * Copyright (c) 2008-2010, Code Aurora Forum. All rights reserved. + * Copyright (c) 2008-2011, Code Aurora Forum. All rights reserved. * * Partly derived from ehci-fsl.c and ehci-hcd.c * Copyright (c) 2000-2004 by David Brownell @@ -22,103 +22,26 @@ * along with this program; if not, you can find it at http://www.fsf.org */ -#include <linux/platform_device.h> #include <linux/clk.h> #include <linux/err.h> +#include <linux/io.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/platform_device.h> #include <linux/pm_runtime.h> - #include <linux/usb/otg.h> #include <linux/usb/msm_hsusb_hw.h> +#include <linux/usb.h> +#include <linux/usb/hcd.h> -#define MSM_USB_BASE (hcd->regs) - -static struct otg_transceiver *otg; - -/* - * ehci_run defined in drivers/usb/host/ehci-hcd.c reset the controller and - * the configuration settings in ehci_msm_reset vanish after controller is - * reset. Resetting the controler in ehci_run seems to be un-necessary - * provided HCD reset the controller before calling ehci_run. Most of the HCD - * do but some are not. So this function is same as ehci_run but we don't - * reset the controller here. - */ -static int ehci_msm_run(struct usb_hcd *hcd) -{ - struct ehci_hcd *ehci = hcd_to_ehci(hcd); - u32 temp; - u32 hcc_params; - - hcd->uses_new_polling = 1; +#include "ehci.h" - ehci_writel(ehci, ehci->periodic_dma, &ehci->regs->frame_list); - ehci_writel(ehci, (u32)ehci->async->qh_dma, &ehci->regs->async_next); - - /* - * hcc_params controls whether ehci->regs->segment must (!!!) - * be used; it constrains QH/ITD/SITD and QTD locations. - * pci_pool consistent memory always uses segment zero. - * streaming mappings for I/O buffers, like pci_map_single(), - * can return segments above 4GB, if the device allows. - * - * NOTE: the dma mask is visible through dma_supported(), so - * drivers can pass this info along ... like NETIF_F_HIGHDMA, - * Scsi_Host.highmem_io, and so forth. It's readonly to all - * host side drivers though. - */ - hcc_params = ehci_readl(ehci, &ehci->caps->hcc_params); - if (HCC_64BIT_ADDR(hcc_params)) - ehci_writel(ehci, 0, &ehci->regs->segment); - - /* - * Philips, Intel, and maybe others need CMD_RUN before the - * root hub will detect new devices (why?); NEC doesn't - */ - ehci->command &= ~(CMD_LRESET|CMD_IAAD|CMD_PSE|CMD_ASE|CMD_RESET); - ehci->command |= CMD_RUN; - ehci_writel(ehci, ehci->command, &ehci->regs->command); - dbg_cmd(ehci, "init", ehci->command); +#define MSM_USB_BASE (hcd->regs) - /* - * Start, enabling full USB 2.0 functionality ... usb 1.1 devices - * are explicitly handed to companion controller(s), so no TT is - * involved with the root hub. (Except where one is integrated, - * and there's no companion controller unless maybe for USB OTG.) - * - * Turning on the CF flag will transfer ownership of all ports - * from the companions to the EHCI controller. If any of the - * companions are in the middle of a port reset at the time, it - * could cause trouble. Write-locking ehci_cf_port_reset_rwsem - * guarantees that no resets are in progress. After we set CF, - * a short delay lets the hardware catch up; new resets shouldn't - * be started before the port switching actions could complete. - */ - down_write(&ehci_cf_port_reset_rwsem); - hcd->state = HC_STATE_RUNNING; - ehci_writel(ehci, FLAG_CF, &ehci->regs->configured_flag); - ehci_readl(ehci, &ehci->regs->command); /* unblock posted writes */ - usleep_range(5000, 5500); - up_write(&ehci_cf_port_reset_rwsem); - ehci->last_periodic_enable = ktime_get_real(); - - temp = HC_VERSION(ehci_readl(ehci, &ehci->caps->hc_capbase)); - ehci_info(ehci, - "USB %x.%x started, EHCI %x.%02x%s\n", - ((ehci->sbrn & 0xf0)>>4), (ehci->sbrn & 0x0f), - temp >> 8, temp & 0xff, - ignore_oc ? ", overcurrent ignored" : ""); - - ehci_writel(ehci, INTR_MASK, - &ehci->regs->intr_enable); /* Turn On Interrupts */ - - /* GRR this is run-once init(), being done every time the HC starts. - * So long as they're part of class devices, we can't do it init() - * since the class device isn't created that early. - */ - create_debug_files(ehci); - create_companion_file(ehci); +#define DRIVER_DESC "Qualcomm On-Chip EHCI Host Controller" - return 0; -} +static const char hcd_name[] = "ehci-msm"; +static struct hc_driver __read_mostly msm_hc_driver; static int ehci_msm_reset(struct usb_hcd *hcd) { @@ -126,21 +49,9 @@ static int ehci_msm_reset(struct usb_hcd *hcd) int retval; ehci->caps = USB_CAPLENGTH; - ehci->regs = USB_CAPLENGTH + - HC_LENGTH(ehci_readl(ehci, &ehci->caps->hc_capbase)); - - /* cache the data to minimize the chip reads*/ - ehci->hcs_params = ehci_readl(ehci, &ehci->caps->hcs_params); - hcd->has_tt = 1; - ehci->sbrn = HCD_USB2; - - /* data structure init */ - retval = ehci_init(hcd); - if (retval) - return retval; - retval = ehci_reset(ehci); + retval = ehci_setup(hcd); if (retval) return retval; @@ -151,60 +62,14 @@ static int ehci_msm_reset(struct usb_hcd *hcd) /* Disable streaming mode and select host mode */ writel(0x13, USB_USBMODE); - ehci_port_power(ehci, 1); return 0; } -static struct hc_driver msm_hc_driver = { - .description = hcd_name, - .product_desc = "Qualcomm On-Chip EHCI Host Controller", - .hcd_priv_size = sizeof(struct ehci_hcd), - - /* - * generic hardware linkage - */ - .irq = ehci_irq, - .flags = HCD_USB2 | HCD_MEMORY, - - .reset = ehci_msm_reset, - .start = ehci_msm_run, - - .stop = ehci_stop, - .shutdown = ehci_shutdown, - - /* - * managing i/o requests and associated device resources - */ - .urb_enqueue = ehci_urb_enqueue, - .urb_dequeue = ehci_urb_dequeue, - .endpoint_disable = ehci_endpoint_disable, - .endpoint_reset = ehci_endpoint_reset, - .clear_tt_buffer_complete = ehci_clear_tt_buffer_complete, - - /* - * scheduling support - */ - .get_frame_number = ehci_get_frame, - - /* - * root hub support - */ - .hub_status_data = ehci_hub_status_data, - .hub_control = ehci_hub_control, - .relinquish_port = ehci_relinquish_port, - .port_handed_over = ehci_port_handed_over, - - /* - * PM support - */ - .bus_suspend = ehci_bus_suspend, - .bus_resume = ehci_bus_resume, -}; - static int ehci_msm_probe(struct platform_device *pdev) { struct usb_hcd *hcd; struct resource *res; + struct usb_phy *phy; int ret; dev_dbg(&pdev->dev, "ehci_msm proble\n"); @@ -231,10 +96,9 @@ static int ehci_msm_probe(struct platform_device *pdev) hcd->rsrc_start = res->start; hcd->rsrc_len = resource_size(res); - hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len); - if (!hcd->regs) { - dev_err(&pdev->dev, "ioremap failed\n"); - ret = -ENOMEM; + hcd->regs = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(hcd->regs)) { + ret = PTR_ERR(hcd->regs); goto put_hcd; } @@ -243,19 +107,24 @@ static int ehci_msm_probe(struct platform_device *pdev) * powering up VBUS, mapping of registers address space and power * management. */ - otg = otg_get_transceiver(); - if (!otg) { + if (pdev->dev.of_node) + phy = devm_usb_get_phy_by_phandle(&pdev->dev, "usb-phy", 0); + else + phy = devm_usb_get_phy(&pdev->dev, USB_PHY_TYPE_USB2); + + if (IS_ERR(phy)) { dev_err(&pdev->dev, "unable to find transceiver\n"); - ret = -ENODEV; - goto unmap; + ret = -EPROBE_DEFER; + goto put_hcd; } - ret = otg_set_host(otg, &hcd->self); + ret = otg_set_host(phy->otg, &hcd->self); if (ret < 0) { dev_err(&pdev->dev, "unable to register with transceiver\n"); - goto put_transceiver; + goto put_hcd; } + hcd->phy = phy; device_init_wakeup(&pdev->dev, 1); /* * OTG device parent of HCD takes care of putting @@ -264,19 +133,17 @@ static int ehci_msm_probe(struct platform_device *pdev) pm_runtime_no_callbacks(&pdev->dev); pm_runtime_enable(&pdev->dev); + /* FIXME: need to call usb_add_hcd() here? */ + return 0; -put_transceiver: - otg_put_transceiver(otg); -unmap: - iounmap(hcd->regs); put_hcd: usb_put_hcd(hcd); return ret; } -static int __devexit ehci_msm_remove(struct platform_device *pdev) +static int ehci_msm_remove(struct platform_device *pdev) { struct usb_hcd *hcd = platform_get_drvdata(pdev); @@ -284,8 +151,9 @@ static int __devexit ehci_msm_remove(struct platform_device *pdev) pm_runtime_disable(&pdev->dev); pm_runtime_set_suspended(&pdev->dev); - otg_set_host(otg, NULL); - otg_put_transceiver(otg); + otg_set_host(hcd->phy->otg, NULL); + + /* FIXME: need to call usb_remove_hcd() here? */ usb_put_hcd(hcd); @@ -296,24 +164,11 @@ static int __devexit ehci_msm_remove(struct platform_device *pdev) static int ehci_msm_pm_suspend(struct device *dev) { struct usb_hcd *hcd = dev_get_drvdata(dev); - bool wakeup = device_may_wakeup(dev); + bool do_wakeup = device_may_wakeup(dev); dev_dbg(dev, "ehci-msm PM suspend\n"); - /* - * EHCI helper function has also the same check before manipulating - * port wakeup flags. We do check here the same condition before - * calling the same helper function to avoid bringing hardware - * from Low power mode when there is no need for adjusting port - * wakeup flags. - */ - if (hcd->self.root_hub->do_remote_wakeup && !wakeup) { - pm_runtime_resume(dev); - ehci_prepare_ports_for_controller_suspend(hcd_to_ehci(hcd), - wakeup); - } - - return 0; + return ehci_suspend(hcd, do_wakeup); } static int ehci_msm_pm_resume(struct device *dev) @@ -321,7 +176,7 @@ static int ehci_msm_pm_resume(struct device *dev) struct usb_hcd *hcd = dev_get_drvdata(dev); dev_dbg(dev, "ehci-msm PM resume\n"); - ehci_prepare_ports_for_controller_resume(hcd_to_ehci(hcd)); + ehci_resume(hcd, false); return 0; } @@ -335,11 +190,43 @@ static const struct dev_pm_ops ehci_msm_dev_pm_ops = { .resume = ehci_msm_pm_resume, }; +static struct of_device_id msm_ehci_dt_match[] = { + { .compatible = "qcom,ehci-host", }, + {} +}; +MODULE_DEVICE_TABLE(of, msm_ehci_dt_match); + static struct platform_driver ehci_msm_driver = { .probe = ehci_msm_probe, - .remove = __devexit_p(ehci_msm_remove), + .remove = ehci_msm_remove, .driver = { .name = "msm_hsusb_host", .pm = &ehci_msm_dev_pm_ops, + .of_match_table = msm_ehci_dt_match, }, }; + +static const struct ehci_driver_overrides msm_overrides __initdata = { + .reset = ehci_msm_reset, +}; + +static int __init ehci_msm_init(void) +{ + if (usb_disabled()) + return -ENODEV; + + pr_info("%s: " DRIVER_DESC "\n", hcd_name); + ehci_init_driver(&msm_hc_driver, &msm_overrides); + return platform_driver_register(&ehci_msm_driver); +} +module_init(ehci_msm_init); + +static void __exit ehci_msm_cleanup(void) +{ + platform_driver_unregister(&ehci_msm_driver); +} +module_exit(ehci_msm_cleanup); + +MODULE_DESCRIPTION(DRIVER_DESC); +MODULE_ALIAS("platform:msm-ehci"); +MODULE_LICENSE("GPL"); |