1 files changed, 362 insertions, 160 deletions

diff --git a/drivers/usb/host/ehci-hub.c b/drivers/usb/host/ehci-hub.c
index 77bbb2357e4..cc305c71ac3 100644
--- a/drivers/usb/host/ehci-hub.c
+++ b/drivers/usb/host/ehci-hub.c
@@ -33,14 +33,11 @@
 
 #ifdef	CONFIG_PM
 
-static int ehci_hub_control(
-	struct usb_hcd	*hcd,
-	u16		typeReq,
-	u16		wValue,
-	u16		wIndex,
-	char		*buf,
-	u16		wLength
-);
+static int persist_enabled_on_companion(struct usb_device *udev, void *unused)
+{
+	return !udev->maxchild && udev->persist_enabled &&
+		udev->bus->root_hub->speed < USB_SPEED_HIGH;
+}
 
 /* After a power loss, ports that were owned by the companion must be
  * reset so that the companion can still own them.
@@ -56,9 +53,33 @@ static void ehci_handover_companion_ports(struct ehci_hcd *ehci)
 	if (!ehci->owned_ports)
 		return;
 
+	/*
+	 * USB 1.1 devices are mostly HIDs, which don't need to persist across
+	 * suspends. If we ensure that none of our companion's devices have
+	 * persist_enabled (by looking through all USB 1.1 buses in the system),
+	 * we can skip this and avoid slowing resume down. Devices without
+	 * persist will just get reenumerated shortly after resume anyway.
+	 */
+	if (!usb_for_each_dev(NULL, persist_enabled_on_companion))
+		return;
+
+	/* Make sure the ports are powered */
+	port = HCS_N_PORTS(ehci->hcs_params);
+	while (port--) {
+		if (test_bit(port, &ehci->owned_ports)) {
+			reg = &ehci->regs->port_status[port];
+			status = ehci_readl(ehci, reg) & ~PORT_RWC_BITS;
+			if (!(status & PORT_POWER)) {
+				status |= PORT_POWER;
+				ehci_writel(ehci, status, reg);
+			}
+		}
+	}
+
 	/* Give the connections some time to appear */
 	msleep(20);
 
+	spin_lock_irq(&ehci->lock);
 	port = HCS_N_PORTS(ehci->hcs_params);
 	while (port--) {
 		if (test_bit(port, &ehci->owned_ports)) {
@@ -70,23 +91,30 @@ static void ehci_handover_companion_ports(struct ehci_hcd *ehci)
 				clear_bit(port, &ehci->owned_ports);
 			else if (test_bit(port, &ehci->companion_ports))
 				ehci_writel(ehci, status & ~PORT_PE, reg);
-			else
+			else {
+				spin_unlock_irq(&ehci->lock);
 				ehci_hub_control(hcd, SetPortFeature,
 						USB_PORT_FEAT_RESET, port + 1,
 						NULL, 0);
+				spin_lock_irq(&ehci->lock);
+			}
 		}
 	}
+	spin_unlock_irq(&ehci->lock);
 
 	if (!ehci->owned_ports)
 		return;
 	msleep(90);		/* Wait for resets to complete */
 
+	spin_lock_irq(&ehci->lock);
 	port = HCS_N_PORTS(ehci->hcs_params);
 	while (port--) {
 		if (test_bit(port, &ehci->owned_ports)) {
+			spin_unlock_irq(&ehci->lock);
 			ehci_hub_control(hcd, GetPortStatus,
 					0, port + 1,
 					(char *) &buf, sizeof(buf));
+			spin_lock_irq(&ehci->lock);
 
 			/* The companion should now own the port,
 			 * but if something went wrong the port must not
@@ -105,6 +133,7 @@ static void ehci_handover_companion_ports(struct ehci_hcd *ehci)
 	}
 
 	ehci->owned_ports = 0;
+	spin_unlock_irq(&ehci->lock);
 }
 
 static int ehci_port_change(struct ehci_hcd *ehci)
@@ -128,12 +157,11 @@ static int ehci_port_change(struct ehci_hcd *ehci)
 	return 0;
 }
 
-static __maybe_unused void ehci_adjust_port_wakeup_flags(struct ehci_hcd *ehci,
+static void ehci_adjust_port_wakeup_flags(struct ehci_hcd *ehci,
 		bool suspending, bool do_wakeup)
 {
 	int		port;
 	u32		temp;
-	unsigned long	flags;
 
 	/* If remote wakeup is enabled for the root hub but disabled
 	 * for the controller, we must adjust all the port wakeup flags
@@ -143,22 +171,20 @@ static __maybe_unused void ehci_adjust_port_wakeup_flags(struct ehci_hcd *ehci,
 	if (!ehci_to_hcd(ehci)->self.root_hub->do_remote_wakeup || do_wakeup)
 		return;
 
-	spin_lock_irqsave(&ehci->lock, flags);
+	spin_lock_irq(&ehci->lock);
 
 	/* clear phy low-power mode before changing wakeup flags */
-	if (ehci->has_hostpc) {
+	if (ehci->has_tdi_phy_lpm) {
 		port = HCS_N_PORTS(ehci->hcs_params);
 		while (port--) {
-			u32 __iomem	*hostpc_reg;
+			u32 __iomem	*hostpc_reg = &ehci->regs->hostpc[port];
 
-			hostpc_reg = (u32 __iomem *)((u8 *) ehci->regs
-					+ HOSTPC0 + 4 * port);
 			temp = ehci_readl(ehci, hostpc_reg);
 			ehci_writel(ehci, temp & ~HOSTPC_PHCD, hostpc_reg);
 		}
-		spin_unlock_irqrestore(&ehci->lock, flags);
+		spin_unlock_irq(&ehci->lock);
 		msleep(5);
-		spin_lock_irqsave(&ehci->lock, flags);
+		spin_lock_irq(&ehci->lock);
 	}
 
 	port = HCS_N_PORTS(ehci->hcs_params);
@@ -176,19 +202,15 @@ static __maybe_unused void ehci_adjust_port_wakeup_flags(struct ehci_hcd *ehci,
 			else
 				t2 |= PORT_WKOC_E | PORT_WKCONN_E;
 		}
-		ehci_vdbg(ehci, "port %d, %08x -> %08x\n",
-				port + 1, t1, t2);
 		ehci_writel(ehci, t2, reg);
 	}
 
 	/* enter phy low-power mode again */
-	if (ehci->has_hostpc) {
+	if (ehci->has_tdi_phy_lpm) {
 		port = HCS_N_PORTS(ehci->hcs_params);
 		while (port--) {
-			u32 __iomem	*hostpc_reg;
+			u32 __iomem	*hostpc_reg = &ehci->regs->hostpc[port];
 
-			hostpc_reg = (u32 __iomem *)((u8 *) ehci->regs
-					+ HOSTPC0 + 4 * port);
 			temp = ehci_readl(ehci, hostpc_reg);
 			ehci_writel(ehci, temp | HOSTPC_PHCD, hostpc_reg);
 		}
@@ -198,7 +220,7 @@ static __maybe_unused void ehci_adjust_port_wakeup_flags(struct ehci_hcd *ehci,
 	if (!suspending && ehci_port_change(ehci))
 		usb_hcd_resume_root_hub(ehci_to_hcd(ehci));
 
-	spin_unlock_irqrestore(&ehci->lock, flags);
+	spin_unlock_irq(&ehci->lock);
 }
 
 static int ehci_bus_suspend (struct usb_hcd *hcd)
@@ -207,15 +229,19 @@ static int ehci_bus_suspend (struct usb_hcd *hcd)
 	int			port;
 	int			mask;
 	int			changed;
+	bool			fs_idle_delay;
 
 	ehci_dbg(ehci, "suspend root hub\n");
 
 	if (time_before (jiffies, ehci->next_statechange))
 		msleep(5);
-	del_timer_sync(&ehci->watchdog);
-	del_timer_sync(&ehci->iaa_watchdog);
+
+	/* stop the schedules */
+	ehci_quiesce(ehci);
 
 	spin_lock_irq (&ehci->lock);
+	if (ehci->rh_state < EHCI_RH_RUNNING)
+		goto done;
 
 	/* Once the controller is stopped, port resumes that are already
 	 * in progress won't complete.  Hence if remote wakeup is enabled
@@ -223,24 +249,13 @@ static int ehci_bus_suspend (struct usb_hcd *hcd)
 	 * remote wakeup, we must fail the suspend.
 	 */
 	if (hcd->self.root_hub->do_remote_wakeup) {
-		port = HCS_N_PORTS(ehci->hcs_params);
-		while (port--) {
-			if (ehci->reset_done[port] != 0) {
-				spin_unlock_irq(&ehci->lock);
-				ehci_dbg(ehci, "suspend failed because "
-						"port %d is resuming\n",
-						port + 1);
-				return -EBUSY;
-			}
+		if (ehci->resuming_ports) {
+			spin_unlock_irq(&ehci->lock);
+			ehci_dbg(ehci, "suspend failed because a port is resuming\n");
+			return -EBUSY;
 		}
 	}
 
-	/* stop schedules, clean any completed work */
-	if (ehci->rh_state == EHCI_RH_RUNNING)
-		ehci_quiesce (ehci);
-	ehci->command = ehci_readl(ehci, &ehci->regs->command);
-	ehci_work(ehci);
-
 	/* Unlike other USB host controller types, EHCI doesn't have
 	 * any notion of "global" or bus-wide suspend.  The driver has
 	 * to manually suspend all the active unsuspended ports, and
@@ -249,6 +264,7 @@ static int ehci_bus_suspend (struct usb_hcd *hcd)
 	ehci->bus_suspended = 0;
 	ehci->owned_ports = 0;
 	changed = 0;
+	fs_idle_delay = false;
 	port = HCS_N_PORTS(ehci->hcs_params);
 	while (port--) {
 		u32 __iomem	*reg = &ehci->regs->port_status [port];
@@ -277,25 +293,37 @@ static int ehci_bus_suspend (struct usb_hcd *hcd)
 		}
 
 		if (t1 != t2) {
-			ehci_vdbg (ehci, "port %d, %08x -> %08x\n",
-				port + 1, t1, t2);
+			/*
+			 * On some controllers, Wake-On-Disconnect will
+			 * generate false wakeup signals until the bus
+			 * switches over to full-speed idle.  For their
+			 * sake, add a delay if we need one.
+			 */
+			if ((t2 & PORT_WKDISC_E) &&
+					ehci_port_speed(ehci, t2) ==
+						USB_PORT_STAT_HIGH_SPEED)
+				fs_idle_delay = true;
 			ehci_writel(ehci, t2, reg);
 			changed = 1;
 		}
 	}
+	spin_unlock_irq(&ehci->lock);
+
+	if ((changed && ehci->has_tdi_phy_lpm) || fs_idle_delay) {
+		/*
+		 * Wait for HCD to enter low-power mode or for the bus
+		 * to switch to full-speed idle.
+		 */
+		usleep_range(5000, 5500);
+	}
 
-	if (changed && ehci->has_hostpc) {
-		spin_unlock_irq(&ehci->lock);
-		msleep(5);	/* 5 ms for HCD to enter low-power mode */
+	if (changed && ehci->has_tdi_phy_lpm) {
 		spin_lock_irq(&ehci->lock);
-
 		port = HCS_N_PORTS(ehci->hcs_params);
 		while (port--) {
-			u32 __iomem	*hostpc_reg;
+			u32 __iomem	*hostpc_reg = &ehci->regs->hostpc[port];
 			u32		t3;
 
-			hostpc_reg = (u32 __iomem *)((u8 *) ehci->regs
-					+ HOSTPC0 + 4 * port);
 			t3 = ehci_readl(ehci, hostpc_reg);
 			ehci_writel(ehci, t3 | HOSTPC_PHCD, hostpc_reg);
 			t3 = ehci_readl(ehci, hostpc_reg);
@@ -303,6 +331,7 @@ static int ehci_bus_suspend (struct usb_hcd *hcd)
 					port, (t3 & HOSTPC_PHCD) ?
 					"succeeded" : "failed");
 		}
+		spin_unlock_irq(&ehci->lock);
 	}
 
 	/* Apparently some devices need a >= 1-uframe delay here */
@@ -311,10 +340,19 @@ static int ehci_bus_suspend (struct usb_hcd *hcd)
 
 	/* turn off now-idle HC */
 	ehci_halt (ehci);
+
+	spin_lock_irq(&ehci->lock);
+	if (ehci->enabled_hrtimer_events & BIT(EHCI_HRTIMER_POLL_DEAD))
+		ehci_handle_controller_death(ehci);
+	if (ehci->rh_state != EHCI_RH_RUNNING)
+		goto done;
 	ehci->rh_state = EHCI_RH_SUSPENDED;
 
-	if (ehci->reclaim)
-		end_unlink_async(ehci);
+	end_unlink_async(ehci);
+	unlink_empty_async_suspended(ehci);
+	ehci_handle_start_intr_unlinks(ehci);
+	ehci_handle_intr_unlinks(ehci);
+	end_free_itds(ehci);
 
 	/* allow remote wakeup */
 	mask = INTR_MASK;
@@ -323,13 +361,13 @@ static int ehci_bus_suspend (struct usb_hcd *hcd)
 	ehci_writel(ehci, mask, &ehci->regs->intr_enable);
 	ehci_readl(ehci, &ehci->regs->intr_enable);
 
+ done:
 	ehci->next_statechange = jiffies + msecs_to_jiffies(10);
+	ehci->enabled_hrtimer_events = 0;
+	ehci->next_hrtimer_event = EHCI_HRTIMER_NO_EVENT;
 	spin_unlock_irq (&ehci->lock);
 
-	/* ehci_work() may have re-enabled the watchdog timer, which we do not
-	 * want, and so we must delete any pending watchdog timer events.
-	 */
-	del_timer_sync(&ehci->watchdog);
+	hrtimer_cancel(&ehci->hrtimer);
 	return 0;
 }
 
@@ -346,16 +384,14 @@ static int ehci_bus_resume (struct usb_hcd *hcd)
 	if (time_before (jiffies, ehci->next_statechange))
 		msleep(5);
 	spin_lock_irq (&ehci->lock);
-	if (!HCD_HW_ACCESSIBLE(hcd)) {
-		spin_unlock_irq(&ehci->lock);
-		return -ESHUTDOWN;
-	}
+	if (!HCD_HW_ACCESSIBLE(hcd) || ehci->shutdown)
+		goto shutdown;
 
 	if (unlikely(ehci->debug)) {
-		if (!dbgp_reset_prep())
+		if (!dbgp_reset_prep(hcd))
 			ehci->debug = NULL;
 		else
-			dbgp_external_startup();
+			dbgp_external_startup(hcd);
 	}
 
 	/* Ideally and we've got a real resume here, and no port's power
@@ -379,24 +415,39 @@ static int ehci_bus_resume (struct usb_hcd *hcd)
 	ehci_writel(ehci, (u32) ehci->async->qh_dma, &ehci->regs->async_next);
 
 	/* restore CMD_RUN, framelist size, and irq threshold */
+	ehci->command |= CMD_RUN;
 	ehci_writel(ehci, ehci->command, &ehci->regs->command);
 	ehci->rh_state = EHCI_RH_RUNNING;
 
-	/* Some controller/firmware combinations need a delay during which
-	 * they set up the port statuses.  See Bugzilla #8190. */
-	spin_unlock_irq(&ehci->lock);
-	msleep(8);
-	spin_lock_irq(&ehci->lock);
+	/*
+	 * According to Bugzilla #8190, the port status for some controllers
+	 * will be wrong without a delay. At their wrong status, the port
+	 * is enabled, but not suspended neither resumed.
+	 */
+	i = HCS_N_PORTS(ehci->hcs_params);
+	while (i--) {
+		temp = ehci_readl(ehci, &ehci->regs->port_status[i]);
+		if ((temp & PORT_PE) &&
+				!(temp & (PORT_SUSPEND | PORT_RESUME))) {
+			ehci_dbg(ehci, "Port status(0x%x) is wrong\n", temp);
+			spin_unlock_irq(&ehci->lock);
+			msleep(8);
+			spin_lock_irq(&ehci->lock);
+			break;
+		}
+	}
+
+	if (ehci->shutdown)
+		goto shutdown;
 
 	/* clear phy low-power mode before resume */
-	if (ehci->bus_suspended && ehci->has_hostpc) {
+	if (ehci->bus_suspended && ehci->has_tdi_phy_lpm) {
 		i = HCS_N_PORTS(ehci->hcs_params);
 		while (i--) {
 			if (test_bit(i, &ehci->bus_suspended)) {
-				u32 __iomem	*hostpc_reg;
+				u32 __iomem	*hostpc_reg =
+							&ehci->regs->hostpc[i];
 
-				hostpc_reg = (u32 __iomem *)((u8 *) ehci->regs
-						+ HOSTPC0 + 4 * i);
 				temp = ehci_readl(ehci, hostpc_reg);
 				ehci_writel(ehci, temp & ~HOSTPC_PHCD,
 						hostpc_reg);
@@ -405,6 +456,8 @@ static int ehci_bus_resume (struct usb_hcd *hcd)
 		spin_unlock_irq(&ehci->lock);
 		msleep(5);
 		spin_lock_irq(&ehci->lock);
+		if (ehci->shutdown)
+			goto shutdown;
 	}
 
 	/* manually resume the ports we suspended during bus_suspend() */
@@ -425,38 +478,37 @@ static int ehci_bus_resume (struct usb_hcd *hcd)
 		spin_unlock_irq(&ehci->lock);
 		msleep(20);
 		spin_lock_irq(&ehci->lock);
+		if (ehci->shutdown)
+			goto shutdown;
 	}
 
 	i = HCS_N_PORTS (ehci->hcs_params);
 	while (i--) {
 		temp = ehci_readl(ehci, &ehci->regs->port_status [i]);
 		if (test_bit(i, &resume_needed)) {
-			temp &= ~(PORT_RWC_BITS | PORT_RESUME);
+			temp &= ~(PORT_RWC_BITS | PORT_SUSPEND | PORT_RESUME);
 			ehci_writel(ehci, temp, &ehci->regs->port_status [i]);
-			ehci_vdbg (ehci, "resumed port %d\n", i + 1);
 		}
 	}
-	(void) ehci_readl(ehci, &ehci->regs->command);
-
-	/* maybe re-activate the schedule(s) */
-	temp = 0;
-	if (ehci->async->qh_next.qh)
-		temp |= CMD_ASE;
-	if (ehci->periodic_sched)
-		temp |= CMD_PSE;
-	if (temp) {
-		ehci->command |= temp;
-		ehci_writel(ehci, ehci->command, &ehci->regs->command);
-	}
 
 	ehci->next_statechange = jiffies + msecs_to_jiffies(5);
+	spin_unlock_irq(&ehci->lock);
+
+	ehci_handover_companion_ports(ehci);
 
 	/* Now we can safely re-enable irqs */
+	spin_lock_irq(&ehci->lock);
+	if (ehci->shutdown)
+		goto shutdown;
 	ehci_writel(ehci, INTR_MASK, &ehci->regs->intr_enable);
+	(void) ehci_readl(ehci, &ehci->regs->intr_enable);
+	spin_unlock_irq(&ehci->lock);
 
-	spin_unlock_irq (&ehci->lock);
-	ehci_handover_companion_ports(ehci);
 	return 0;
+
+ shutdown:
+	spin_unlock_irq(&ehci->lock);
+	return -ESHUTDOWN;
 }
 
 #else
@@ -536,7 +588,8 @@ static int check_reset_complete (
 		if (ehci->has_amcc_usb23)
 			set_ohci_hcfs(ehci, 1);
 	} else {
-		ehci_dbg (ehci, "port %d high speed\n", index + 1);
+		ehci_dbg(ehci, "port %d reset complete, port enabled\n",
+			index + 1);
 		/* ensure 440EPx ohci controller state is suspended */
 		if (ehci->has_amcc_usb23)
 			set_ohci_hcfs(ehci, 0);
@@ -554,15 +607,11 @@ static int
 ehci_hub_status_data (struct usb_hcd *hcd, char *buf)
 {
 	struct ehci_hcd	*ehci = hcd_to_ehci (hcd);
-	u32		temp, status = 0;
+	u32		temp, status;
 	u32		mask;
 	int		ports, i, retval = 1;
 	unsigned long	flags;
-	u32		ppcd = 0;
-
-	/* if !USB_SUSPEND, root hub timers won't get shut down ... */
-	if (ehci->rh_state != EHCI_RH_RUNNING)
-		return 0;
+	u32		ppcd = ~0;
 
 	/* init status to no-changes */
 	buf [0] = 0;
@@ -572,6 +621,11 @@ ehci_hub_status_data (struct usb_hcd *hcd, char *buf)
 		retval++;
 	}
 
+	/* Inform the core about resumes-in-progress by returning
+	 * a non-zero value even if there are no status changes.
+	 */
+	status = ehci->resuming_ports;
+
 	/* Some boards (mostly VIA?) report bogus overcurrent indications,
 	 * causing massive log spam unless we completely ignore them.  It
 	 * may be relevant that VIA VT8235 controllers, where PORT_POWER is
@@ -595,9 +649,10 @@ ehci_hub_status_data (struct usb_hcd *hcd, char *buf)
 
 	for (i = 0; i < ports; i++) {
 		/* leverage per-port change bits feature */
-		if (ehci->has_ppcd && !(ppcd & (1 << i)))
-			continue;
-		temp = ehci_readl(ehci, &ehci->regs->port_status [i]);
+		if (ppcd & (1 << i))
+			temp = ehci_readl(ehci, &ehci->regs->port_status[i]);
+		else
+			temp = 0;
 
 		/*
 		 * Return status information even for ports with OWNER set.
@@ -616,7 +671,11 @@ ehci_hub_status_data (struct usb_hcd *hcd, char *buf)
 			status = STS_PCD;
 		}
 	}
-	/* FIXME autosuspend idle root hubs */
+
+	/* If a resume is in progress, make sure it can finish */
+	if (ehci->resuming_ports)
+		mod_timer(&hcd->rh_timer, jiffies + msecs_to_jiffies(25));
+
 	spin_unlock_irqrestore (&ehci->lock, flags);
 	return status ? retval : 0;
 }
@@ -657,8 +716,147 @@ ehci_hub_descriptor (
 }
 
 /*-------------------------------------------------------------------------*/
+#ifdef CONFIG_USB_HCD_TEST_MODE
 
-static int ehci_hub_control (
+#define EHSET_TEST_SINGLE_STEP_SET_FEATURE 0x06
+
+static void usb_ehset_completion(struct urb *urb)
+{
+	struct completion  *done = urb->context;
+
+	complete(done);
+}
+static int submit_single_step_set_feature(
+	struct usb_hcd	*hcd,
+	struct urb	*urb,
+	int		is_setup
+);
+
+/*
+ * Allocate and initialize a control URB. This request will be used by the
+ * EHSET SINGLE_STEP_SET_FEATURE test in which the DATA and STATUS stages
+ * of the GetDescriptor request are sent 15 seconds after the SETUP stage.
+ * Return NULL if failed.
+ */
+static struct urb *request_single_step_set_feature_urb(
+	struct usb_device	*udev,
+	void			*dr,
+	void			*buf,
+	struct completion	*done
+) {
+	struct urb *urb;
+	struct usb_hcd *hcd = bus_to_hcd(udev->bus);
+	struct usb_host_endpoint *ep;
+
+	urb = usb_alloc_urb(0, GFP_KERNEL);
+	if (!urb)
+		return NULL;
+
+	urb->pipe = usb_rcvctrlpipe(udev, 0);
+	ep = (usb_pipein(urb->pipe) ? udev->ep_in : udev->ep_out)
+				[usb_pipeendpoint(urb->pipe)];
+	if (!ep) {
+		usb_free_urb(urb);
+		return NULL;
+	}
+
+	urb->ep = ep;
+	urb->dev = udev;
+	urb->setup_packet = (void *)dr;
+	urb->transfer_buffer = buf;
+	urb->transfer_buffer_length = USB_DT_DEVICE_SIZE;
+	urb->complete = usb_ehset_completion;
+	urb->status = -EINPROGRESS;
+	urb->actual_length = 0;
+	urb->transfer_flags = URB_DIR_IN;
+	usb_get_urb(urb);
+	atomic_inc(&urb->use_count);
+	atomic_inc(&urb->dev->urbnum);
+	urb->setup_dma = dma_map_single(
+			hcd->self.controller,
+			urb->setup_packet,
+			sizeof(struct usb_ctrlrequest),
+			DMA_TO_DEVICE);
+	urb->transfer_dma = dma_map_single(
+			hcd->self.controller,
+			urb->transfer_buffer,
+			urb->transfer_buffer_length,
+			DMA_FROM_DEVICE);
+	urb->context = done;
+	return urb;
+}
+
+static int ehset_single_step_set_feature(struct usb_hcd *hcd, int port)
+{
+	int retval = -ENOMEM;
+	struct usb_ctrlrequest *dr;
+	struct urb *urb;
+	struct usb_device *udev;
+	struct ehci_hcd *ehci = hcd_to_ehci(hcd);
+	struct usb_device_descriptor *buf;
+	DECLARE_COMPLETION_ONSTACK(done);
+
+	/* Obtain udev of the rhub's child port */
+	udev = usb_hub_find_child(hcd->self.root_hub, port);
+	if (!udev) {
+		ehci_err(ehci, "No device attached to the RootHub\n");
+		return -ENODEV;
+	}
+	buf = kmalloc(USB_DT_DEVICE_SIZE, GFP_KERNEL);
+	if (!buf)
+		return -ENOMEM;
+
+	dr = kmalloc(sizeof(struct usb_ctrlrequest), GFP_KERNEL);
+	if (!dr) {
+		kfree(buf);
+		return -ENOMEM;
+	}
+
+	/* Fill Setup packet for GetDescriptor */
+	dr->bRequestType = USB_DIR_IN;
+	dr->bRequest = USB_REQ_GET_DESCRIPTOR;
+	dr->wValue = cpu_to_le16(USB_DT_DEVICE << 8);
+	dr->wIndex = 0;
+	dr->wLength = cpu_to_le16(USB_DT_DEVICE_SIZE);
+	urb = request_single_step_set_feature_urb(udev, dr, buf, &done);
+	if (!urb)
+		goto cleanup;
+
+	/* Submit just the SETUP stage */
+	retval = submit_single_step_set_feature(hcd, urb, 1);
+	if (retval)
+		goto out1;
+	if (!wait_for_completion_timeout(&done, msecs_to_jiffies(2000))) {
+		usb_kill_urb(urb);
+		retval = -ETIMEDOUT;
+		ehci_err(ehci, "%s SETUP stage timed out on ep0\n", __func__);
+		goto out1;
+	}
+	msleep(15 * 1000);
+
+	/* Complete remaining DATA and STATUS stages using the same URB */
+	urb->status = -EINPROGRESS;
+	usb_get_urb(urb);
+	atomic_inc(&urb->use_count);
+	atomic_inc(&urb->dev->urbnum);
+	retval = submit_single_step_set_feature(hcd, urb, 0);
+	if (!retval && !wait_for_completion_timeout(&done,
+						msecs_to_jiffies(2000))) {
+		usb_kill_urb(urb);
+		retval = -ETIMEDOUT;
+		ehci_err(ehci, "%s IN stage timed out on ep0\n", __func__);
+	}
+out1:
+	usb_free_urb(urb);
+cleanup:
+	kfree(dr);
+	kfree(buf);
+	return retval;
+}
+#endif /* CONFIG_USB_HCD_TEST_MODE */
+/*-------------------------------------------------------------------------*/
+
+int ehci_hub_control(
 	struct usb_hcd	*hcd,
 	u16		typeReq,
 	u16		wValue,
@@ -670,7 +868,7 @@ static int ehci_hub_control (
 	int		ports = HCS_N_PORTS (ehci->hcs_params);
 	u32 __iomem	*status_reg = &ehci->regs->port_status[
 				(wIndex & 0xff) - 1];
-	u32 __iomem	*hostpc_reg = NULL;
+	u32 __iomem	*hostpc_reg = &ehci->regs->hostpc[(wIndex & 0xff) - 1];
 	u32		temp, temp1, status;
 	unsigned long	flags;
 	int		retval = 0;
@@ -683,9 +881,6 @@ static int ehci_hub_control (
 	 * power, "this is the one", etc.  EHCI spec supports this.
 	 */
 
-	if (ehci->has_hostpc)
-		hostpc_reg = (u32 __iomem *)((u8 *)ehci->regs
-				+ HOSTPC0 + 4 * ((wIndex & 0xff) - 1));
 	spin_lock_irqsave (&ehci->lock, flags);
 	switch (typeReq) {
 	case ClearHubFeature:
@@ -703,6 +898,7 @@ static int ehci_hub_control (
 			goto error;
 		wIndex--;
 		temp = ehci_readl(ehci, status_reg);
+		temp &= ~PORT_RWC_BITS;
 
 		/*
 		 * Even if OWNER is set, so the port is owned by the
@@ -716,8 +912,7 @@ static int ehci_hub_control (
 			ehci_writel(ehci, temp & ~PORT_PE, status_reg);
 			break;
 		case USB_PORT_FEAT_C_ENABLE:
-			ehci_writel(ehci, (temp & ~PORT_RWC_BITS) | PORT_PEC,
-					status_reg);
+			ehci_writel(ehci, temp | PORT_PEC, status_reg);
 			break;
 		case USB_PORT_FEAT_SUSPEND:
 			if (temp & PORT_RESET)
@@ -727,7 +922,7 @@ static int ehci_hub_control (
 #ifdef CONFIG_USB_OTG
 			if ((hcd->self.otg_port == (wIndex + 1))
 			    && hcd->self.b_hnp_enable) {
-				otg_start_hnp(ehci->transceiver);
+				otg_start_hnp(hcd->phy->otg);
 				break;
 			}
 #endif
@@ -737,7 +932,7 @@ static int ehci_hub_control (
 				goto error;
 
 			/* clear phy low-power mode before resume */
-			if (hostpc_reg) {
+			if (ehci->has_tdi_phy_lpm) {
 				temp1 = ehci_readl(ehci, hostpc_reg);
 				ehci_writel(ehci, temp1 & ~HOSTPC_PHCD,
 						hostpc_reg);
@@ -746,32 +941,26 @@ static int ehci_hub_control (
 				spin_lock_irqsave(&ehci->lock, flags);
 			}
 			/* resume signaling for 20 msec */
-			temp &= ~(PORT_RWC_BITS | PORT_WAKE_BITS);
+			temp &= ~PORT_WAKE_BITS;
 			ehci_writel(ehci, temp | PORT_RESUME, status_reg);
 			ehci->reset_done[wIndex] = jiffies
 					+ msecs_to_jiffies(20);
+			set_bit(wIndex, &ehci->resuming_ports);
+			usb_hcd_start_port_resume(&hcd->self, wIndex);
 			break;
 		case USB_PORT_FEAT_C_SUSPEND:
 			clear_bit(wIndex, &ehci->port_c_suspend);
 			break;
 		case USB_PORT_FEAT_POWER:
 			if (HCS_PPC (ehci->hcs_params))
-				ehci_writel(ehci,
-					  temp & ~(PORT_RWC_BITS | PORT_POWER),
-					  status_reg);
+				ehci_writel(ehci, temp & ~PORT_POWER,
+						status_reg);
 			break;
 		case USB_PORT_FEAT_C_CONNECTION:
-			if (ehci->has_lpm) {
-				/* clear PORTSC bits on disconnect */
-				temp &= ~PORT_LPM;
-				temp &= ~PORT_DEV_ADDR;
-			}
-			ehci_writel(ehci, (temp & ~PORT_RWC_BITS) | PORT_CSC,
-					status_reg);
+			ehci_writel(ehci, temp | PORT_CSC, status_reg);
 			break;
 		case USB_PORT_FEAT_C_OVER_CURRENT:
-			ehci_writel(ehci, (temp & ~PORT_RWC_BITS) | PORT_OCC,
-					status_reg);
+			ehci_writel(ehci, temp | PORT_OCC, status_reg);
 			break;
 		case USB_PORT_FEAT_C_RESET:
 			/* GetPortStatus clears reset */
@@ -813,7 +1002,8 @@ static int ehci_hub_control (
 			 * power switching; they're allowed to just limit the
 			 * current.  khubd will turn the power back on.
 			 */
-			if ((temp & PORT_OC) && HCS_PPC(ehci->hcs_params)) {
+			if (((temp & PORT_OC) || (ehci->need_oc_pp_cycle))
+					&& HCS_PPC(ehci->hcs_params)) {
 				ehci_writel(ehci,
 					temp & ~(PORT_RWC_BITS | PORT_POWER),
 					status_reg);
@@ -821,47 +1011,47 @@ static int ehci_hub_control (
 			}
 		}
 
-		/* whoever resumes must GetPortStatus to complete it!! */
-		if (temp & PORT_RESUME) {
+		/* no reset or resume pending */
+		if (!ehci->reset_done[wIndex]) {
 
 			/* Remote Wakeup received? */
-			if (!ehci->reset_done[wIndex]) {
+			if (temp & PORT_RESUME) {
 				/* resume signaling for 20 msec */
 				ehci->reset_done[wIndex] = jiffies
 						+ msecs_to_jiffies(20);
+				usb_hcd_start_port_resume(&hcd->self, wIndex);
+				set_bit(wIndex, &ehci->resuming_ports);
 				/* check the port again */
 				mod_timer(&ehci_to_hcd(ehci)->rh_timer,
 						ehci->reset_done[wIndex]);
 			}
 
-			/* resume completed? */
-			else if (time_after_eq(jiffies,
-					ehci->reset_done[wIndex])) {
-				clear_bit(wIndex, &ehci->suspended_ports);
-				set_bit(wIndex, &ehci->port_c_suspend);
-				ehci->reset_done[wIndex] = 0;
+		/* reset or resume not yet complete */
+		} else if (!time_after_eq(jiffies, ehci->reset_done[wIndex])) {
+			;	/* wait until it is complete */
 
-				/* stop resume signaling */
-				temp = ehci_readl(ehci, status_reg);
-				ehci_writel(ehci,
-					temp & ~(PORT_RWC_BITS | PORT_RESUME),
-					status_reg);
-				retval = handshake(ehci, status_reg,
-					   PORT_RESUME, 0, 2000 /* 2msec */);
-				if (retval != 0) {
-					ehci_err(ehci,
-						"port %d resume error %d\n",
+		/* resume completed */
+		} else if (test_bit(wIndex, &ehci->resuming_ports)) {
+			clear_bit(wIndex, &ehci->suspended_ports);
+			set_bit(wIndex, &ehci->port_c_suspend);
+			ehci->reset_done[wIndex] = 0;
+			usb_hcd_end_port_resume(&hcd->self, wIndex);
+
+			/* stop resume signaling */
+			temp &= ~(PORT_RWC_BITS | PORT_SUSPEND | PORT_RESUME);
+			ehci_writel(ehci, temp, status_reg);
+			clear_bit(wIndex, &ehci->resuming_ports);
+			retval = ehci_handshake(ehci, status_reg,
+					PORT_RESUME, 0, 2000 /* 2msec */);
+			if (retval != 0) {
+				ehci_err(ehci, "port %d resume error %d\n",
 						wIndex + 1, retval);
-					goto error;
-				}
-				temp &= ~(PORT_SUSPEND|PORT_RESUME|(3<<10));
+				goto error;
 			}
-		}
+			temp = ehci_readl(ehci, status_reg);
 
 		/* whoever resets must GetPortStatus to complete it!! */
-		if ((temp & PORT_RESET)
-				&& time_after_eq(jiffies,
-					ehci->reset_done[wIndex])) {
+		} else {
 			status |= USB_PORT_STAT_C_RESET << 16;
 			ehci->reset_done [wIndex] = 0;
 
@@ -871,7 +1061,7 @@ static int ehci_hub_control (
 			/* REVISIT:  some hardware needs 550+ usec to clear
 			 * this bit; seems too long to spin routinely...
 			 */
-			retval = handshake(ehci, status_reg,
+			retval = ehci_handshake(ehci, status_reg,
 					PORT_RESET, 0, 1000);
 			if (retval != 0) {
 				ehci_err (ehci, "port %d reset error %d\n",
@@ -884,9 +1074,6 @@ static int ehci_hub_control (
 					ehci_readl(ehci, status_reg));
 		}
 
-		if (!(temp & (PORT_RESUME|PORT_RESET)))
-			ehci->reset_done[wIndex] = 0;
-
 		/* transfer dedicated ports to the companion hc */
 		if ((temp & PORT_CONNECT) &&
 				test_bit(wIndex, &ehci->companion_ports)) {
@@ -920,9 +1107,11 @@ static int ehci_hub_control (
 			status |= USB_PORT_STAT_SUSPEND;
 		} else if (test_bit(wIndex, &ehci->suspended_ports)) {
 			clear_bit(wIndex, &ehci->suspended_ports);
+			clear_bit(wIndex, &ehci->resuming_ports);
 			ehci->reset_done[wIndex] = 0;
 			if (temp & PORT_PE)
 				set_bit(wIndex, &ehci->port_c_suspend);
+			usb_hcd_end_port_resume(&hcd->self, wIndex);
 		}
 
 		if (temp & PORT_OC)
@@ -934,10 +1123,8 @@ static int ehci_hub_control (
 		if (test_bit(wIndex, &ehci->port_c_suspend))
 			status |= USB_PORT_STAT_C_SUSPEND << 16;
 
-#ifndef	VERBOSE_DEBUG
-	if (status & ~0xffff)	/* only if wPortChange is interesting */
-#endif
-		dbg_port (ehci, "GetStatus", wIndex + 1, temp);
+		if (status & ~0xffff)	/* only if wPortChange is interesting */
+			dbg_port(ehci, "GetStatus", wIndex + 1, temp);
 		put_unaligned_le32(status, buf);
 		break;
 	case SetHubFeature:
@@ -980,12 +1167,12 @@ static int ehci_hub_control (
 
 			/* After above check the port must be connected.
 			 * Set appropriate bit thus could put phy into low power
-			 * mode if we have hostpc feature
+			 * mode if we have tdi_phy_lpm feature
 			 */
 			temp &= ~PORT_WKCONN_E;
 			temp |= PORT_WKDISC_E | PORT_WKOC_E;
 			ehci_writel(ehci, temp | PORT_SUSPEND, status_reg);
-			if (hostpc_reg) {
+			if (ehci->has_tdi_phy_lpm) {
 				spin_unlock_irqrestore(&ehci->lock, flags);
 				msleep(5);/* 5ms for HCD enter low pwr mode */
 				spin_lock_irqsave(&ehci->lock, flags);
@@ -1005,7 +1192,7 @@ static int ehci_hub_control (
 						status_reg);
 			break;
 		case USB_PORT_FEAT_RESET:
-			if (temp & PORT_RESUME)
+			if (temp & (PORT_SUSPEND|PORT_RESUME))
 				goto error;
 			/* line status bits may report this as low speed,
 			 * which can be fine if this root hub has a
@@ -1019,7 +1206,6 @@ static int ehci_hub_control (
 					wIndex + 1);
 				temp |= PORT_OWNER;
 			} else {
-				ehci_vdbg (ehci, "port %d reset\n", wIndex + 1);
 				temp |= PORT_RESET;
 				temp &= ~PORT_PE;
 
@@ -1040,9 +1226,20 @@ static int ehci_hub_control (
 		 * about the EHCI-specific stuff.
 		 */
 		case USB_PORT_FEAT_TEST:
+#ifdef CONFIG_USB_HCD_TEST_MODE
+			if (selector == EHSET_TEST_SINGLE_STEP_SET_FEATURE) {
+				spin_unlock_irqrestore(&ehci->lock, flags);
+				retval = ehset_single_step_set_feature(hcd,
+									wIndex);
+				spin_lock_irqsave(&ehci->lock, flags);
+				break;
+			}
+#endif
 			if (!selector || selector > 5)
 				goto error;
+			spin_unlock_irqrestore(&ehci->lock, flags);
 			ehci_quiesce(ehci);
+			spin_lock_irqsave(&ehci->lock, flags);
 
 			/* Put all enabled ports into suspend */
 			while (ports--) {
@@ -1054,7 +1251,11 @@ static int ehci_hub_control (
 					ehci_writel(ehci, temp | PORT_SUSPEND,
 							sreg);
 			}
+
+			spin_unlock_irqrestore(&ehci->lock, flags);
 			ehci_halt(ehci);
+			spin_lock_irqsave(&ehci->lock, flags);
+
 			temp = ehci_readl(ehci, status_reg);
 			temp |= selector << 16;
 			ehci_writel(ehci, temp, status_reg);
@@ -1075,6 +1276,7 @@ error_exit:
 	spin_unlock_irqrestore (&ehci->lock, flags);
 	return retval;
 }
+EXPORT_SYMBOL_GPL(ehci_hub_control);
 
 static void ehci_relinquish_port(struct usb_hcd *hcd, int portnum)
 {