diff options
Diffstat (limited to 'drivers/usb/host/Kconfig')
| -rw-r--r-- | drivers/usb/host/Kconfig | 157 |
1 files changed, 108 insertions, 49 deletions
diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig index 4263d011392..03314f861be 100644 --- a/drivers/usb/host/Kconfig +++ b/drivers/usb/host/Kconfig @@ -29,14 +29,13 @@ if USB_XHCI_HCD config USB_XHCI_PLATFORM tristate -config USB_XHCI_HCD_DEBUGGING - bool "Debugging for the xHCI host controller" +config USB_XHCI_MVEBU + tristate "xHCI support for Marvell Armada 375/38x" + select USB_XHCI_PLATFORM + depends on ARCH_MVEBU || COMPILE_TEST ---help--- - Say 'Y' to turn on debugging for the xHCI host controller driver. - This will spew debugging output, even in interrupt context. - This should only be used for debugging xHCI driver bugs. - - If unsure, say N. + Say 'Y' to enable the support for the xHCI host controller + found in Marvell Armada 375/38x ARM SOCs. endif # USB_XHCI_HCD @@ -63,7 +62,7 @@ config USB_EHCI_HCD config USB_EHCI_ROOT_HUB_TT bool "Root Hub Transaction Translators" - depends on USB_EHCI_HCD || USB_CHIPIDEA_HOST + depends on USB_EHCI_HCD ---help--- Some EHCI chips have vendor-specific extensions to integrate transaction translators, so that no OHCI or UHCI companion @@ -75,7 +74,7 @@ config USB_EHCI_ROOT_HUB_TT config USB_EHCI_TT_NEWSCHED bool "Improved Transaction Translator scheduling" - depends on USB_EHCI_HCD || USB_CHIPIDEA_HOST + depends on USB_EHCI_HCD default y ---help--- This changes the periodic scheduling code to fill more of the low @@ -113,12 +112,6 @@ config USB_EHCI_HCD_PMC_MSP Enables support for the onchip USB controller on the PMC_MSP7100 Family SoC's. If unsure, say N. -config USB_EHCI_BIG_ENDIAN_MMIO - bool - -config USB_EHCI_BIG_ENDIAN_DESC - bool - config XPS_USB_HCD_XILINX bool "Use Xilinx usb host EHCI controller core" depends on (PPC32 || MICROBLAZE) @@ -148,13 +141,11 @@ config USB_EHCI_MXC config USB_EHCI_HCD_OMAP tristate "EHCI support for OMAP3 and later chips" depends on ARCH_OMAP + select NOP_USB_XCEIV default y ---help--- Enables support for the on-chip EHCI controller on OMAP3 and later chips. - If your system uses a PHY on the USB port, you will need to - enable USB_PHY and the appropriate PHY driver as well. Most - boards need the NOP_USB_XCEIV PHY driver. config USB_EHCI_HCD_ORION tristate "Support for Marvell EBU on-chip EHCI USB controller" @@ -185,10 +176,8 @@ config USB_EHCI_HCD_AT91 config USB_EHCI_MSM tristate "Support for Qualcomm QSD/MSM on-chip EHCI USB controller" - depends on ARCH_MSM - depends on USB_PHY + depends on ARCH_MSM || ARCH_QCOM select USB_EHCI_ROOT_HUB_TT - select USB_MSM_OTG ---help--- Enables support for the USB Host controller present on the Qualcomm chipsets. Root Hub has inbuilt TT. @@ -221,12 +210,11 @@ config USB_EHCI_SH Enables support for the on-chip EHCI controller on the SuperH. If you use the PCI EHCI controller, this option is not necessary. -config USB_EHCI_S5P +config USB_EHCI_EXYNOS tristate "EHCI support for Samsung S5P/EXYNOS SoC Series" depends on PLAT_S5P || ARCH_EXYNOS help - Enable support for the Samsung S5Pxxxx and Exynos3/4/5 SOC's - on-chip EHCI controller. + Enable support for the Samsung Exynos SOC's on-chip EHCI controller. config USB_EHCI_MV bool "EHCI support for Marvell PXA/MMP USB controller" @@ -242,7 +230,7 @@ config USB_EHCI_MV on-chip EHCI USB controller" for those. config USB_W90X900_EHCI - bool "W90X900(W90P910) EHCI support" + tristate "W90X900(W90P910) EHCI support" depends on ARCH_W90X900 ---help--- Enables support for the W90X900 USB controller @@ -296,7 +284,6 @@ endif # USB_EHCI_HCD config USB_OXU210HP_HCD tristate "OXU210HP HCD support" - depends on GENERIC_HARDIRQS ---help--- The OXU210HP is an USB host/OTG/device controller. Enable this option if your board has this chip. If unsure, say N. @@ -334,7 +321,6 @@ config USB_ISP1760_HCD config USB_ISP1362_HCD tristate "ISP1362 HCD support" - default N ---help--- Supports the Philips ISP1362 chip as a host controller @@ -346,7 +332,6 @@ config USB_ISP1362_HCD config USB_FUSBH200_HCD tristate "FUSBH200 HCD support" depends on USB - default N ---help--- Faraday FUSBH200 is designed to meet USB2.0 EHCI specification with minor modification. @@ -354,10 +339,30 @@ config USB_FUSBH200_HCD To compile this driver as a module, choose M here: the module will be called fusbh200-hcd. +config USB_FOTG210_HCD + tristate "FOTG210 HCD support" + depends on USB + ---help--- + Faraday FOTG210 is an OTG controller which can be configured as + an USB2.0 host. It is designed to meet USB2.0 EHCI specification + with minor modification. + + To compile this driver as a module, choose M here: the + module will be called fotg210-hcd. + +config USB_MAX3421_HCD + tristate "MAX3421 HCD (USB-over-SPI) support" + depends on USB && SPI + ---help--- + The Maxim MAX3421E chip supports standard USB 2.0-compliant + full-speed devices either in host or peripheral mode. This + driver supports the host-mode of the MAX3421E only. + + To compile this driver as a module, choose M here: the module will + be called max3421-hcd. + config USB_OHCI_HCD tristate "OHCI HCD (USB 1.1) support" - select ISP1301_OMAP if MACH_OMAP_H2 || MACH_OMAP_H3 - depends on USB_ISP1301 || !ARCH_LPC32XX ---help--- The Open Host Controller Interface (OHCI) is a standard for accessing USB 1.1 host controller hardware. It does more in hardware than Intel's @@ -374,20 +379,72 @@ config USB_OHCI_HCD if USB_OHCI_HCD config USB_OHCI_HCD_OMAP1 - bool "OHCI support for OMAP1/2 chips" + tristate "OHCI support for OMAP1/2 chips" depends on ARCH_OMAP1 + depends on ISP1301_OMAP || !(MACH_OMAP_H2 || MACH_OMAP_H3) default y ---help--- Enables support for the OHCI controller on OMAP1/2 chips. +config USB_OHCI_HCD_SPEAR + tristate "Support for ST SPEAr on-chip OHCI USB controller" + depends on USB_OHCI_HCD && PLAT_SPEAR + default y + ---help--- + Enables support for the on-chip OHCI controller on + ST SPEAr chips. + +config USB_OHCI_HCD_S3C2410 + tristate "OHCI support for Samsung S3C24xx/S3C64xx SoC series" + depends on USB_OHCI_HCD && (ARCH_S3C24XX || ARCH_S3C64XX) + default y + ---help--- + Enables support for the on-chip OHCI controller on + S3C24xx/S3C64xx chips. + +config USB_OHCI_HCD_LPC32XX + tristate "Support for LPC on-chip OHCI USB controller" + depends on USB_OHCI_HCD && ARCH_LPC32XX + depends on USB_ISP1301 + default y + ---help--- + Enables support for the on-chip OHCI controller on + NXP chips. + +config USB_OHCI_HCD_PXA27X + tristate "Support for PXA27X/PXA3XX on-chip OHCI USB controller" + depends on USB_OHCI_HCD && (PXA27x || PXA3xx) + default y + ---help--- + Enables support for the on-chip OHCI controller on + PXA27x/PXA3xx chips. + +config USB_OHCI_HCD_AT91 + tristate "Support for Atmel on-chip OHCI USB controller" + depends on USB_OHCI_HCD && ARCH_AT91 + default y + ---help--- + Enables support for the on-chip OHCI controller on + Atmel chips. + config USB_OHCI_HCD_OMAP3 - bool "OHCI support for OMAP3 and later chips" + tristate "OHCI support for OMAP3 and later chips" depends on (ARCH_OMAP3 || ARCH_OMAP4) default y ---help--- Enables support for the on-chip OHCI controller on OMAP3 and later chips. +config USB_OHCI_HCD_DAVINCI + bool "OHCI support for TI DaVinci DA8xx" + depends on ARCH_DAVINCI_DA8XX + depends on USB_OHCI_HCD=y + default y + help + Enables support for the DaVinci DA8xx integrated OHCI + controller. This driver cannot currently be a loadable + module because it lacks a proper PHY abstraction. + config USB_OHCI_ATH79 bool "USB OHCI support for the Atheros AR71XX/AR7240 SoCs (DEPRECATED)" depends on (SOC_AR71XX || SOC_AR724X) @@ -461,8 +518,8 @@ config USB_OHCI_SH If you use the PCI OHCI controller, this option is not necessary. config USB_OHCI_EXYNOS - boolean "OHCI support for Samsung EXYNOS SoC Series" - depends on ARCH_EXYNOS + tristate "OHCI support for Samsung S5P/EXYNOS SoC Series" + depends on PLAT_S5P || ARCH_EXYNOS help Enable support for the Samsung Exynos SOC's on-chip OHCI controller. @@ -497,20 +554,6 @@ config USB_OCTEON_OHCI controller. It is needed for low-speed USB 1.0 device support. All CN6XXX based chips with USB are supported. - -config USB_OHCI_BIG_ENDIAN_DESC - bool - default n - -config USB_OHCI_BIG_ENDIAN_MMIO - bool - default n - -config USB_OHCI_LITTLE_ENDIAN - bool - default n if STB03xxx || PPC_MPC52xx - default y - endif # USB_OHCI_HCD config USB_UHCI_HCD @@ -566,7 +609,6 @@ config FHCI_DEBUG config USB_U132_HCD tristate "Elan U132 Adapter Host Controller" depends on USB_FTDI_ELAN - default M help The U132 adapter is a USB to CardBus adapter specifically designed for PC cards that contain an OHCI host controller. Typical PC cards @@ -710,3 +752,20 @@ config USB_HCD_SSB for ehci and ohci. If unsure, say N. + +config USB_HCD_TEST_MODE + bool "HCD test mode support" + ---help--- + Say 'Y' to enable additional software test modes that may be + supported by the host controller drivers. + + One such test mode is the Embedded High-speed Host Electrical Test + (EHSET) for EHCI host controller hardware, specifically the "Single + Step Set Feature" test. Typically this will be enabled for On-the-Go + or embedded hosts that need to undergo USB-IF compliance testing with + the aid of special testing hardware. In the future, this may expand + to include other tests that require support from a HCD driver. + + This option is of interest only to developers who need to validate + their USB hardware designs. It is not needed for normal use. If + unsure, say N. |