diff options
Diffstat (limited to 'drivers/usb/core/hub.c')
| -rw-r--r-- | drivers/usb/core/hub.c | 1366 |
1 files changed, 786 insertions, 580 deletions
diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c index e6b682c6c23..0e950ad8cb2 100644 --- a/drivers/usb/core/hub.c +++ b/drivers/usb/core/hub.c @@ -33,21 +33,9 @@ #include "hub.h" -/* if we are in debug mode, always announce new devices */ -#ifdef DEBUG -#ifndef CONFIG_USB_ANNOUNCE_NEW_DEVICES -#define CONFIG_USB_ANNOUNCE_NEW_DEVICES -#endif -#endif - #define USB_VENDOR_GENESYS_LOGIC 0x05e3 #define HUB_QUIRK_CHECK_PORT_AUTOSUSPEND 0x01 -static inline int hub_is_superspeed(struct usb_device *hdev) -{ - return (hdev->descriptor.bDeviceProtocol == USB_HUB_PR_SS); -} - /* Protect struct usb_device->state and ->children members * Note: Both are also protected by ->dev.sem, except that ->state can * change to USB_STATE_NOTATTACHED even when the semaphore isn't held. */ @@ -62,6 +50,9 @@ static DECLARE_WAIT_QUEUE_HEAD(khubd_wait); static struct task_struct *khubd_task; +/* synchronize hub-port add/remove and peering operations */ +DEFINE_MUTEX(usb_port_peer_mutex); + /* cycle leds on hubs that aren't blinking for attention */ static bool blinkenlights = 0; module_param (blinkenlights, bool, S_IRUGO); @@ -120,7 +111,7 @@ static inline char *portspeed(struct usb_hub *hub, int portstatus) if (hub_is_superspeed(hub->hdev)) return "5.0 Gb/s"; if (portstatus & USB_PORT_STAT_HIGH_SPEED) - return "480 Mb/s"; + return "480 Mb/s"; else if (portstatus & USB_PORT_STAT_LOW_SPEED) return "1.5 Mb/s"; else @@ -148,19 +139,27 @@ static int usb_device_supports_lpm(struct usb_device *udev) return 0; } - /* All USB 3.0 must support LPM, but we need their max exit latency - * information from the SuperSpeed Extended Capabilities BOS descriptor. + /* + * According to the USB 3.0 spec, all USB 3.0 devices must support LPM. + * However, there are some that don't, and they set the U1/U2 exit + * latencies to zero. */ if (!udev->bos->ss_cap) { - dev_warn(&udev->dev, "No LPM exit latency info found. " - "Power management will be impacted.\n"); + dev_info(&udev->dev, "No LPM exit latency info found, disabling LPM.\n"); return 0; } - if (udev->parent->lpm_capable) - return 1; - dev_warn(&udev->dev, "Parent hub missing LPM exit latency info. " - "Power management will be impacted.\n"); + if (udev->bos->ss_cap->bU1devExitLat == 0 && + udev->bos->ss_cap->bU2DevExitLat == 0) { + if (udev->parent) + dev_info(&udev->dev, "LPM exit latency is zeroed, disabling LPM.\n"); + else + dev_info(&udev->dev, "We don't know the algorithms for LPM for this host, disabling LPM.\n"); + return 0; + } + + if (!udev->parent || udev->parent->lpm_capable) + return 1; return 0; } @@ -310,9 +309,9 @@ static void usb_set_lpm_parameters(struct usb_device *udev) return; udev_u1_del = udev->bos->ss_cap->bU1devExitLat; - udev_u2_del = udev->bos->ss_cap->bU2DevExitLat; + udev_u2_del = le16_to_cpu(udev->bos->ss_cap->bU2DevExitLat); hub_u1_del = udev->parent->bos->ss_cap->bU1devExitLat; - hub_u2_del = udev->parent->bos->ss_cap->bU2DevExitLat; + hub_u2_del = le16_to_cpu(udev->parent->bos->ss_cap->bU2DevExitLat); usb_set_lpm_mel(udev, &udev->u1_params, udev_u1_del, hub, &udev->parent->u1_params, hub_u1_del); @@ -411,30 +410,35 @@ static int set_port_feature(struct usb_device *hdev, int port1, int feature) NULL, 0, 1000); } +static char *to_led_name(int selector) +{ + switch (selector) { + case HUB_LED_AMBER: + return "amber"; + case HUB_LED_GREEN: + return "green"; + case HUB_LED_OFF: + return "off"; + case HUB_LED_AUTO: + return "auto"; + default: + return "??"; + } +} + /* * USB 2.0 spec Section 11.24.2.7.1.10 and table 11-7 * for info about using port indicators */ -static void set_port_led( - struct usb_hub *hub, - int port1, - int selector -) +static void set_port_led(struct usb_hub *hub, int port1, int selector) { - int status = set_port_feature(hub->hdev, (selector << 8) | port1, + struct usb_port *port_dev = hub->ports[port1 - 1]; + int status; + + status = set_port_feature(hub->hdev, (selector << 8) | port1, USB_PORT_FEAT_INDICATOR); - if (status < 0) - dev_dbg (hub->intfdev, - "port %d indicator %s status %d\n", - port1, - ({ char *s; switch (selector) { - case HUB_LED_AMBER: s = "amber"; break; - case HUB_LED_GREEN: s = "green"; break; - case HUB_LED_OFF: s = "off"; break; - case HUB_LED_AUTO: s = "auto"; break; - default: s = "??"; break; - }; s; }), - status); + dev_dbg(&port_dev->dev, "indicator %s status %d\n", + to_led_name(selector), status); } #define LED_CYCLE_PERIOD ((2*HZ)/3) @@ -506,7 +510,8 @@ static void led_work (struct work_struct *work) changed++; } if (changed) - schedule_delayed_work(&hub->leds, LED_CYCLE_PERIOD); + queue_delayed_work(system_power_efficient_wq, + &hub->leds, LED_CYCLE_PERIOD); } /* use a short timeout for hub/port status fetches */ @@ -741,16 +746,20 @@ int usb_hub_set_port_power(struct usb_device *hdev, struct usb_hub *hub, int port1, bool set) { int ret; - struct usb_port *port_dev = hub->ports[port1 - 1]; if (set) ret = set_port_feature(hdev, port1, USB_PORT_FEAT_POWER); else ret = usb_clear_port_feature(hdev, port1, USB_PORT_FEAT_POWER); - if (!ret) - port_dev->power_is_on = set; - return ret; + if (ret) + return ret; + + if (set) + set_bit(port1, hub->power_bits); + else + clear_bit(port1, hub->power_bits); + return 0; } /** @@ -808,16 +817,9 @@ int usb_hub_clear_tt_buffer(struct urb *urb) } EXPORT_SYMBOL_GPL(usb_hub_clear_tt_buffer); -/* If do_delay is false, return the number of milliseconds the caller - * needs to delay. - */ -static unsigned hub_power_on(struct usb_hub *hub, bool do_delay) +static void hub_power_on(struct usb_hub *hub, bool do_delay) { int port1; - unsigned pgood_delay = hub->descriptor->bPwrOn2PwrGood * 2; - unsigned delay; - u16 wHubCharacteristics = - le16_to_cpu(hub->descriptor->wHubCharacteristics); /* Enable power on each port. Some hubs have reserved values * of LPSM (> 2) in their descriptors, even though they are @@ -825,23 +827,19 @@ static unsigned hub_power_on(struct usb_hub *hub, bool do_delay) * but only emulate it. In all cases, the ports won't work * unless we send these messages to the hub. */ - if ((wHubCharacteristics & HUB_CHAR_LPSM) < 2) + if (hub_is_port_power_switchable(hub)) dev_dbg(hub->intfdev, "enabling power on all ports\n"); else dev_dbg(hub->intfdev, "trying to enable port power on " "non-switchable hub\n"); for (port1 = 1; port1 <= hub->hdev->maxchild; port1++) - if (hub->ports[port1 - 1]->power_is_on) + if (test_bit(port1, hub->power_bits)) set_port_feature(hub->hdev, port1, USB_PORT_FEAT_POWER); else usb_clear_port_feature(hub->hdev, port1, USB_PORT_FEAT_POWER); - - /* Wait at least 100 msec for power to become stable */ - delay = max(pgood_delay, (unsigned) 100); if (do_delay) - msleep(delay); - return delay; + msleep(hub_power_on_good_delay(hub)); } static int hub_hub_status(struct usb_hub *hub, @@ -857,7 +855,7 @@ static int hub_hub_status(struct usb_hub *hub, "%s failed (err = %d)\n", __func__, ret); } else { *status = le16_to_cpu(hub->status->hub.wHubStatus); - *change = le16_to_cpu(hub->status->hub.wHubChange); + *change = le16_to_cpu(hub->status->hub.wHubChange); ret = 0; } mutex_unlock(&hub->status_mutex); @@ -891,6 +889,25 @@ static int hub_usb3_port_disable(struct usb_hub *hub, int port1) if (!hub_is_superspeed(hub->hdev)) return -EINVAL; + ret = hub_port_status(hub, port1, &portstatus, &portchange); + if (ret < 0) + return ret; + + /* + * USB controller Advanced Micro Devices, Inc. [AMD] FCH USB XHCI + * Controller [1022:7814] will have spurious result making the following + * usb 3.0 device hotplugging route to the 2.0 root hub and recognized + * as high-speed device if we set the usb 3.0 port link state to + * Disabled. Since it's already in USB_SS_PORT_LS_RX_DETECT state, we + * check the state here to avoid the bug. + */ + if ((portstatus & USB_PORT_STAT_LINK_STATE) == + USB_SS_PORT_LS_RX_DETECT) { + dev_dbg(&hub->ports[port1 - 1]->dev, + "Not disabling port; link state is RxDetect\n"); + return ret; + } + ret = hub_set_port_link_state(hub, port1, USB_SS_PORT_LS_SS_DISABLED); if (ret) return ret; @@ -909,20 +926,20 @@ static int hub_usb3_port_disable(struct usb_hub *hub, int port1) msleep(HUB_DEBOUNCE_STEP); } if (total_time >= HUB_DEBOUNCE_TIMEOUT) - dev_warn(hub->intfdev, "Could not disable port %d after %d ms\n", - port1, total_time); + dev_warn(&hub->ports[port1 - 1]->dev, + "Could not disable after %d ms\n", total_time); return hub_set_port_link_state(hub, port1, USB_SS_PORT_LS_RX_DETECT); } static int hub_port_disable(struct usb_hub *hub, int port1, int set_state) { + struct usb_port *port_dev = hub->ports[port1 - 1]; struct usb_device *hdev = hub->hdev; int ret = 0; - if (hub->ports[port1 - 1]->child && set_state) - usb_set_device_state(hub->ports[port1 - 1]->child, - USB_STATE_NOTATTACHED); + if (port_dev->child && set_state) + usb_set_device_state(port_dev->child, USB_STATE_NOTATTACHED); if (!hub->error) { if (hub_is_superspeed(hub->hdev)) ret = hub_usb3_port_disable(hub, port1); @@ -931,8 +948,7 @@ static int hub_port_disable(struct usb_hub *hub, int port1, int set_state) USB_PORT_FEAT_ENABLE); } if (ret && ret != -ENODEV) - dev_err(hub->intfdev, "cannot disable port %d (err = %d)\n", - port1, ret); + dev_err(&port_dev->dev, "cannot disable (err = %d)\n", ret); return ret; } @@ -943,7 +959,7 @@ static int hub_port_disable(struct usb_hub *hub, int port1, int set_state) */ static void hub_port_logical_disconnect(struct usb_hub *hub, int port1) { - dev_dbg(hub->intfdev, "logical disconnect on port %d\n", port1); + dev_dbg(&hub->ports[port1 - 1]->dev, "logical disconnect\n"); hub_port_disable(hub, port1, 1); /* FIXME let caller ask to power down the port: @@ -956,7 +972,7 @@ static void hub_port_logical_disconnect(struct usb_hub *hub, int port1) */ set_bit(port1, hub->change_bits); - kick_khubd(hub); + kick_khubd(hub); } /** @@ -1046,9 +1062,12 @@ static void hub_activate(struct usb_hub *hub, enum hub_activation_type type) * for HUB_POST_RESET, but it's easier not to. */ if (type == HUB_INIT) { - delay = hub_power_on(hub, false); - PREPARE_DELAYED_WORK(&hub->init_work, hub_init_func2); - schedule_delayed_work(&hub->init_work, + unsigned delay = hub_power_on_good_delay(hub); + + hub_power_on(hub, false); + INIT_DELAYED_WORK(&hub->init_work, hub_init_func2); + queue_delayed_work(system_power_efficient_wq, + &hub->init_work, msecs_to_jiffies(delay)); /* Suppress autosuspend until init is done */ @@ -1080,21 +1099,23 @@ static void hub_activate(struct usb_hub *hub, enum hub_activation_type type) } init2: - /* Check each port and set hub->change_bits to let khubd know + /* + * Check each port and set hub->change_bits to let khubd know * which ports need attention. */ for (port1 = 1; port1 <= hdev->maxchild; ++port1) { - struct usb_device *udev = hub->ports[port1 - 1]->child; + struct usb_port *port_dev = hub->ports[port1 - 1]; + struct usb_device *udev = port_dev->child; u16 portstatus, portchange; portstatus = portchange = 0; status = hub_port_status(hub, port1, &portstatus, &portchange); if (udev || (portstatus & USB_PORT_STAT_CONNECTION)) - dev_dbg(hub->intfdev, - "port %d: status %04x change %04x\n", - port1, portstatus, portchange); + dev_dbg(&port_dev->dev, "status %04x change %04x\n", + portstatus, portchange); - /* After anything other than HUB_RESUME (i.e., initialization + /* + * After anything other than HUB_RESUME (i.e., initialization * or any sort of reset), every port should be disabled. * Unconnected ports should likewise be disabled (paranoia), * and so should ports for which we have no usb_device. @@ -1107,16 +1128,13 @@ static void hub_activate(struct usb_hub *hub, enum hub_activation_type type) /* * USB3 protocol ports will automatically transition * to Enabled state when detect an USB3.0 device attach. - * Do not disable USB3 protocol ports. + * Do not disable USB3 protocol ports, just pretend + * power was lost */ - if (!hub_is_superspeed(hdev)) { + portstatus &= ~USB_PORT_STAT_ENABLE; + if (!hub_is_superspeed(hdev)) usb_clear_port_feature(hdev, port1, USB_PORT_FEAT_ENABLE); - portstatus &= ~USB_PORT_STAT_ENABLE; - } else { - /* Pretend that power was lost for USB3 devs */ - portstatus &= ~USB_PORT_STAT_ENABLE; - } } /* Clear status-change flags; we'll debounce later */ @@ -1130,6 +1148,11 @@ static void hub_activate(struct usb_hub *hub, enum hub_activation_type type) usb_clear_port_feature(hub->hdev, port1, USB_PORT_FEAT_C_ENABLE); } + if (portchange & USB_PORT_STAT_C_RESET) { + need_debounce_delay = true; + usb_clear_port_feature(hub->hdev, port1, + USB_PORT_FEAT_C_RESET); + } if ((portchange & USB_PORT_STAT_C_BH_RESET) && hub_is_superspeed(hub->hdev)) { need_debounce_delay = true; @@ -1147,7 +1170,8 @@ static void hub_activate(struct usb_hub *hub, enum hub_activation_type type) /* Tell khubd to disconnect the device or * check for a new connection */ - if (udev || (portstatus & USB_PORT_STAT_CONNECTION)) + if (udev || (portstatus & USB_PORT_STAT_CONNECTION) || + (portstatus & USB_PORT_STAT_OVERCURRENT)) set_bit(port1, hub->change_bits); } else if (portstatus & USB_PORT_STAT_ENABLE) { @@ -1167,15 +1191,13 @@ static void hub_activate(struct usb_hub *hub, enum hub_activation_type type) set_bit(port1, hub->change_bits); } else if (udev->persist_enabled) { - struct usb_port *port_dev = hub->ports[port1 - 1]; - #ifdef CONFIG_PM udev->reset_resume = 1; #endif /* Don't set the change_bits when the device * was powered off. */ - if (port_dev->power_is_on) + if (test_bit(port1, hub->power_bits)) set_bit(port1, hub->change_bits); } else { @@ -1198,8 +1220,9 @@ static void hub_activate(struct usb_hub *hub, enum hub_activation_type type) /* Don't do a long sleep inside a workqueue routine */ if (type == HUB_INIT2) { - PREPARE_DELAYED_WORK(&hub->init_work, hub_init_func3); - schedule_delayed_work(&hub->init_work, + INIT_DELAYED_WORK(&hub->init_work, hub_init_func3); + queue_delayed_work(system_power_efficient_wq, + &hub->init_work, msecs_to_jiffies(delay)); return; /* Continues at init3: below */ } else { @@ -1213,7 +1236,8 @@ static void hub_activate(struct usb_hub *hub, enum hub_activation_type type) if (status < 0) dev_err(hub->intfdev, "activate --> %d\n", status); if (hub->has_indicators && blinkenlights) - schedule_delayed_work(&hub->leds, LED_CYCLE_PERIOD); + queue_delayed_work(system_power_efficient_wq, + &hub->leds, LED_CYCLE_PERIOD); /* Scan all ports that need attention */ kick_khubd(hub); @@ -1268,12 +1292,22 @@ static void hub_quiesce(struct usb_hub *hub, enum hub_quiescing_type type) flush_work(&hub->tt.clear_work); } +static void hub_pm_barrier_for_all_ports(struct usb_hub *hub) +{ + int i; + + for (i = 0; i < hub->hdev->maxchild; ++i) + pm_runtime_barrier(&hub->ports[i]->dev); +} + /* caller has locked the hub device */ static int hub_pre_reset(struct usb_interface *intf) { struct usb_hub *hub = usb_get_intfdata(intf); hub_quiesce(hub, HUB_PRE_RESET); + hub->in_reset = 1; + hub_pm_barrier_for_all_ports(hub); return 0; } @@ -1282,6 +1316,8 @@ static int hub_post_reset(struct usb_interface *intf) { struct usb_hub *hub = usb_get_intfdata(intf); + hub->in_reset = 0; + hub_pm_barrier_for_all_ports(hub); hub_activate(hub, HUB_POST_RESET); return 0; } @@ -1299,6 +1335,7 @@ static int hub_configure(struct usb_hub *hub, char *message = "out of memory"; unsigned unit_load; unsigned full_load; + unsigned maxchild; hub->buffer = kmalloc(sizeof(*hub->buffer), GFP_KERNEL); if (!hub->buffer) { @@ -1337,12 +1374,11 @@ static int hub_configure(struct usb_hub *hub, goto fail; } - hdev->maxchild = hub->descriptor->bNbrPorts; - dev_info (hub_dev, "%d port%s detected\n", hdev->maxchild, - (hdev->maxchild == 1) ? "" : "s"); + maxchild = hub->descriptor->bNbrPorts; + dev_info(hub_dev, "%d port%s detected\n", maxchild, + (maxchild == 1) ? "" : "s"); - hub->ports = kzalloc(hdev->maxchild * sizeof(struct usb_port *), - GFP_KERNEL); + hub->ports = kzalloc(maxchild * sizeof(struct usb_port *), GFP_KERNEL); if (!hub->ports) { ret = -ENOMEM; goto fail; @@ -1361,13 +1397,13 @@ static int hub_configure(struct usb_hub *hub, if ((wHubCharacteristics & HUB_CHAR_COMPOUND) && !(hub_is_superspeed(hdev))) { int i; - char portstr [USB_MAXCHILDREN + 1]; + char portstr[USB_MAXCHILDREN + 1]; - for (i = 0; i < hdev->maxchild; i++) + for (i = 0; i < maxchild; i++) portstr[i] = hub->descriptor->u.hs.DeviceRemovable [((i + 1) / 8)] & (1 << ((i + 1) % 8)) ? 'F' : 'R'; - portstr[hdev->maxchild] = 0; + portstr[maxchild] = 0; dev_dbg(hub_dev, "compound device; port removable status: %s\n", portstr); } else dev_dbg(hub_dev, "standalone hub\n"); @@ -1429,32 +1465,32 @@ static int hub_configure(struct usb_hub *hub, /* Note 8 FS bit times == (8 bits / 12000000 bps) ~= 666ns */ switch (wHubCharacteristics & HUB_CHAR_TTTT) { - case HUB_TTTT_8_BITS: - if (hdev->descriptor.bDeviceProtocol != 0) { - hub->tt.think_time = 666; - dev_dbg(hub_dev, "TT requires at most %d " - "FS bit times (%d ns)\n", - 8, hub->tt.think_time); - } - break; - case HUB_TTTT_16_BITS: - hub->tt.think_time = 666 * 2; - dev_dbg(hub_dev, "TT requires at most %d " - "FS bit times (%d ns)\n", - 16, hub->tt.think_time); - break; - case HUB_TTTT_24_BITS: - hub->tt.think_time = 666 * 3; - dev_dbg(hub_dev, "TT requires at most %d " - "FS bit times (%d ns)\n", - 24, hub->tt.think_time); - break; - case HUB_TTTT_32_BITS: - hub->tt.think_time = 666 * 4; + case HUB_TTTT_8_BITS: + if (hdev->descriptor.bDeviceProtocol != 0) { + hub->tt.think_time = 666; dev_dbg(hub_dev, "TT requires at most %d " "FS bit times (%d ns)\n", - 32, hub->tt.think_time); - break; + 8, hub->tt.think_time); + } + break; + case HUB_TTTT_16_BITS: + hub->tt.think_time = 666 * 2; + dev_dbg(hub_dev, "TT requires at most %d " + "FS bit times (%d ns)\n", + 16, hub->tt.think_time); + break; + case HUB_TTTT_24_BITS: + hub->tt.think_time = 666 * 3; + dev_dbg(hub_dev, "TT requires at most %d " + "FS bit times (%d ns)\n", + 24, hub->tt.think_time); + break; + case HUB_TTTT_32_BITS: + hub->tt.think_time = 666 * 4; + dev_dbg(hub_dev, "TT requires at most %d " + "FS bit times (%d ns)\n", + 32, hub->tt.think_time); + break; } /* probe() zeroes hub->indicator[] */ @@ -1479,7 +1515,7 @@ static int hub_configure(struct usb_hub *hub, if (hcd->power_budget > 0) hdev->bus_mA = hcd->power_budget; else - hdev->bus_mA = full_load * hdev->maxchild; + hdev->bus_mA = full_load * maxchild; if (hdev->bus_mA >= full_load) hub->mA_per_port = full_load; else { @@ -1494,7 +1530,7 @@ static int hub_configure(struct usb_hub *hub, hub->descriptor->bHubContrCurrent); hub->limited_power = 1; - if (remaining < hdev->maxchild * unit_load) + if (remaining < maxchild * unit_load) dev_warn(hub_dev, "insufficient power available " "to use all downstream ports\n"); @@ -1509,18 +1545,6 @@ static int hub_configure(struct usb_hub *hub, dev_dbg(hub_dev, "%umA bus power budget for each child\n", hub->mA_per_port); - /* Update the HCD's internal representation of this hub before khubd - * starts getting port status changes for devices under the hub. - */ - if (hcd->driver->update_hub_device) { - ret = hcd->driver->update_hub_device(hcd, hdev, - &hub->tt, GFP_KERNEL); - if (ret < 0) { - message = "can't update HCD hub info"; - goto fail; - } - } - ret = hub_hub_status(hub, &hubstatus, &hubchange); if (ret < 0) { message = "can't get hub status"; @@ -1560,15 +1584,37 @@ static int hub_configure(struct usb_hub *hub, /* maybe cycle the hub leds */ if (hub->has_indicators && blinkenlights) - hub->indicator [0] = INDICATOR_CYCLE; + hub->indicator[0] = INDICATOR_CYCLE; - for (i = 0; i < hdev->maxchild; i++) { + mutex_lock(&usb_port_peer_mutex); + for (i = 0; i < maxchild; i++) { ret = usb_hub_create_port_device(hub, i + 1); if (ret < 0) { dev_err(hub->intfdev, "couldn't create port%d device.\n", i + 1); - hdev->maxchild = i; - goto fail_keep_maxchild; + break; + } + } + hdev->maxchild = i; + for (i = 0; i < hdev->maxchild; i++) { + struct usb_port *port_dev = hub->ports[i]; + + pm_runtime_put(&port_dev->dev); + } + + mutex_unlock(&usb_port_peer_mutex); + if (ret < 0) + goto fail; + + /* Update the HCD's internal representation of this hub before khubd + * starts getting port status changes for devices under the hub. + */ + if (hcd->driver->update_hub_device) { + ret = hcd->driver->update_hub_device(hcd, hdev, + &hub->tt, GFP_KERNEL); + if (ret < 0) { + message = "can't update HCD hub info"; + goto fail; } } @@ -1578,8 +1624,6 @@ static int hub_configure(struct usb_hub *hub, return 0; fail: - hdev->maxchild = 0; -fail_keep_maxchild: dev_err (hub_dev, "config failed, %s (err %d)\n", message, ret); /* hub_disconnect() frees urb and descriptor */ @@ -1600,7 +1644,7 @@ static void hub_disconnect(struct usb_interface *intf) { struct usb_hub *hub = usb_get_intfdata(intf); struct usb_device *hdev = interface_to_usbdev(intf); - int i; + int port1; /* Take the hub off the event list and don't let it be added again */ spin_lock_irq(&hub_event_lock); @@ -1615,11 +1659,19 @@ static void hub_disconnect(struct usb_interface *intf) hub->error = 0; hub_quiesce(hub, HUB_DISCONNECT); - usb_set_intfdata (intf, NULL); + mutex_lock(&usb_port_peer_mutex); - for (i = 0; i < hdev->maxchild; i++) - usb_hub_remove_port_device(hub, i + 1); - hub->hdev->maxchild = 0; + /* Avoid races with recursively_mark_NOTATTACHED() */ + spin_lock_irq(&device_state_lock); + port1 = hdev->maxchild; + hdev->maxchild = 0; + usb_set_intfdata(intf, NULL); + spin_unlock_irq(&device_state_lock); + + for (; port1 > 0; --port1) + usb_hub_remove_port_device(hub, port1); + + mutex_unlock(&usb_port_peer_mutex); if (hub->hdev->speed == USB_SPEED_HIGH) highspeed_hubs--; @@ -1679,8 +1731,19 @@ static int hub_probe(struct usb_interface *intf, const struct usb_device_id *id) */ pm_runtime_set_autosuspend_delay(&hdev->dev, 0); - /* Hubs have proper suspend/resume support. */ - usb_enable_autosuspend(hdev); + /* + * Hubs have proper suspend/resume support, except for root hubs + * where the controller driver doesn't have bus_suspend and + * bus_resume methods. + */ + if (hdev->parent) { /* normal device */ + usb_enable_autosuspend(hdev); + } else { /* root hub */ + const struct hc_driver *drv = bus_to_hcd(hdev->bus)->driver; + + if (drv->bus_suspend && drv->bus_resume) + usb_enable_autosuspend(hdev); + } if (hdev->level == MAX_TOPO_LEVEL) { dev_err(&intf->dev, @@ -1788,7 +1851,7 @@ hub_ioctl(struct usb_interface *intf, unsigned int code, void *user_data) * to one of these "claimed" ports, the program will "own" the device. */ static int find_port_owner(struct usb_device *hdev, unsigned port1, - struct dev_state ***ppowner) + struct usb_dev_state ***ppowner) { struct usb_hub *hub = usb_hub_to_struct_hub(hdev); @@ -1806,10 +1869,10 @@ static int find_port_owner(struct usb_device *hdev, unsigned port1, /* In the following three functions, the caller must hold hdev's lock */ int usb_hub_claim_port(struct usb_device *hdev, unsigned port1, - struct dev_state *owner) + struct usb_dev_state *owner) { int rc; - struct dev_state **powner; + struct usb_dev_state **powner; rc = find_port_owner(hdev, port1, &powner); if (rc) @@ -1819,12 +1882,13 @@ int usb_hub_claim_port(struct usb_device *hdev, unsigned port1, *powner = owner; return rc; } +EXPORT_SYMBOL_GPL(usb_hub_claim_port); int usb_hub_release_port(struct usb_device *hdev, unsigned port1, - struct dev_state *owner) + struct usb_dev_state *owner) { int rc; - struct dev_state **powner; + struct usb_dev_state **powner; rc = find_port_owner(hdev, port1, &powner); if (rc) @@ -1834,8 +1898,9 @@ int usb_hub_release_port(struct usb_device *hdev, unsigned port1, *powner = NULL; return rc; } +EXPORT_SYMBOL_GPL(usb_hub_release_port); -void usb_hub_release_all_ports(struct usb_device *hdev, struct dev_state *owner) +void usb_hub_release_all_ports(struct usb_device *hdev, struct usb_dev_state *owner) { struct usb_hub *hub = usb_hub_to_struct_hub(hdev); int n; @@ -1978,7 +2043,7 @@ static void choose_devnum(struct usb_device *udev) if (devnum >= 128) devnum = find_next_zero_bit(bus->devmap.devicemap, 128, 1); - bus->devnum_next = ( devnum >= 127 ? 1 : devnum + 1); + bus->devnum_next = (devnum >= 127 ? 1 : devnum + 1); } if (devnum < 128) { set_bit(devnum, bus->devmap.devicemap); @@ -2010,6 +2075,18 @@ static void hub_free_dev(struct usb_device *udev) hcd->driver->free_dev(hcd, udev); } +static void hub_disconnect_children(struct usb_device *udev) +{ + struct usb_hub *hub = usb_hub_to_struct_hub(udev); + int i; + + /* Free up all the children before we remove this device */ + for (i = 0; i < udev->maxchild; i++) { + if (hub->ports[i]->child) + usb_disconnect(&hub->ports[i]->child); + } +} + /** * usb_disconnect - disconnect a device (usbcore-internal) * @pdev: pointer to device being disconnected @@ -2018,8 +2095,8 @@ static void hub_free_dev(struct usb_device *udev) * Something got disconnected. Get rid of it and all of its children. * * If *pdev is a normal device then the parent hub must already be locked. - * If *pdev is a root hub then this routine will acquire the - * usb_bus_list_lock on behalf of the caller. + * If *pdev is a root hub then the caller must hold the usb_bus_list_lock, + * which protects the set of root hubs as well as the list of buses. * * Only hub drivers (including virtual root hub drivers for host * controllers) should ever call this. @@ -2028,9 +2105,10 @@ static void hub_free_dev(struct usb_device *udev) */ void usb_disconnect(struct usb_device **pdev) { - struct usb_device *udev = *pdev; - struct usb_hub *hub = usb_hub_to_struct_hub(udev); - int i; + struct usb_port *port_dev = NULL; + struct usb_device *udev = *pdev; + struct usb_hub *hub; + int port1; /* mark the device as inactive, so any further urb submissions for * this device (and any of its children) will fail immediately. @@ -2042,11 +2120,7 @@ void usb_disconnect(struct usb_device **pdev) usb_lock_device(udev); - /* Free up all the children before we remove this device */ - for (i = 0; i < udev->maxchild; i++) { - if (hub->ports[i]->child) - usb_disconnect(&hub->ports[i]->child); - } + hub_disconnect_children(udev); /* deallocate hcd/hardware state ... nuking all pending urbs and * cleaning up all state associated with the current configuration @@ -2057,16 +2131,19 @@ void usb_disconnect(struct usb_device **pdev) usb_hcd_synchronize_unlinks(udev); if (udev->parent) { - struct usb_hub *hub = usb_hub_to_struct_hub(udev->parent); - struct usb_port *port_dev = hub->ports[udev->portnum - 1]; + port1 = udev->portnum; + hub = usb_hub_to_struct_hub(udev->parent); + port_dev = hub->ports[port1 - 1]; sysfs_remove_link(&udev->dev.kobj, "port"); sysfs_remove_link(&port_dev->dev.kobj, "device"); - if (!port_dev->did_runtime_put) - pm_runtime_put(&port_dev->dev); - else - port_dev->did_runtime_put = false; + /* + * As usb_port_runtime_resume() de-references udev, make + * sure no resumes occur during removal + */ + if (!test_and_set_bit(port1, hub->child_usage_bits)) + pm_runtime_get_sync(&port_dev->dev); } usb_remove_ep_devs(&udev->ep0); @@ -2088,6 +2165,9 @@ void usb_disconnect(struct usb_device **pdev) *pdev = NULL; spin_unlock_irq(&device_state_lock); + if (port_dev && test_and_clear_bit(port1, hub->child_usage_bits)) + pm_runtime_put(&port_dev->dev); + hub_free_dev(udev); put_device(&udev->dev); @@ -2228,18 +2308,13 @@ static int usb_enumerate_device(struct usb_device *udev) return err; } } - if (udev->wusb == 1 && udev->authorized == 0) { - udev->product = kstrdup("n/a (unauthorized)", GFP_KERNEL); - udev->manufacturer = kstrdup("n/a (unauthorized)", GFP_KERNEL); - udev->serial = kstrdup("n/a (unauthorized)", GFP_KERNEL); - } - else { - /* read the standard strings and cache them if present */ - udev->product = usb_cache_string(udev, udev->descriptor.iProduct); - udev->manufacturer = usb_cache_string(udev, - udev->descriptor.iManufacturer); - udev->serial = usb_cache_string(udev, udev->descriptor.iSerialNumber); - } + + /* read the standard strings and cache them if present */ + udev->product = usb_cache_string(udev, udev->descriptor.iProduct); + udev->manufacturer = usb_cache_string(udev, + udev->descriptor.iManufacturer); + udev->serial = usb_cache_string(udev, udev->descriptor.iSerialNumber); + err = usb_enumerate_device_otg(udev); if (err < 0) return err; @@ -2280,6 +2355,22 @@ static void set_usb_port_removable(struct usb_device *udev) udev->removable = USB_DEVICE_REMOVABLE; else udev->removable = USB_DEVICE_FIXED; + + /* + * Platform firmware may have populated an alternative value for + * removable. If the parent port has a known connect_type use + * that instead. + */ + switch (hub->ports[udev->portnum - 1]->connect_type) { + case USB_PORT_CONNECT_TYPE_HOT_PLUG: + udev->removable = USB_DEVICE_REMOVABLE; + break; + case USB_PORT_CONNECT_TYPE_HARD_WIRED: + udev->removable = USB_DEVICE_FIXED; + break; + default: /* use what was set above */ + break; + } } /** @@ -2349,11 +2440,7 @@ int usb_new_device(struct usb_device *udev) device_enable_async_suspend(&udev->dev); - /* - * check whether the hub marks this port as non-removable. Do it - * now so that platform-specific data can override it in - * device_add() - */ + /* check whether the hub or firmware marks this port as non-removable */ if (udev->parent) set_usb_port_removable(udev); @@ -2370,7 +2457,8 @@ int usb_new_device(struct usb_device *udev) /* Create link files between child device and usb port device. */ if (udev->parent) { struct usb_hub *hub = usb_hub_to_struct_hub(udev->parent); - struct usb_port *port_dev = hub->ports[udev->portnum - 1]; + int port1 = udev->portnum; + struct usb_port *port_dev = hub->ports[port1 - 1]; err = sysfs_create_link(&udev->dev.kobj, &port_dev->dev.kobj, "port"); @@ -2384,7 +2472,8 @@ int usb_new_device(struct usb_device *udev) goto fail; } - pm_runtime_get_sync(&port_dev->dev); + if (!test_and_set_bit(port1, hub->child_usage_bits)) + pm_runtime_get_sync(&port_dev->dev); } (void) usb_create_ep_devs(&udev->dev, &udev->ep0, udev); @@ -2421,16 +2510,6 @@ int usb_deauthorize_device(struct usb_device *usb_dev) usb_dev->authorized = 0; usb_set_configuration(usb_dev, -1); - kfree(usb_dev->product); - usb_dev->product = kstrdup("n/a (unauthorized)", GFP_KERNEL); - kfree(usb_dev->manufacturer); - usb_dev->manufacturer = kstrdup("n/a (unauthorized)", GFP_KERNEL); - kfree(usb_dev->serial); - usb_dev->serial = kstrdup("n/a (unauthorized)", GFP_KERNEL); - - usb_destroy_configuration(usb_dev); - usb_dev->descriptor.bNumConfigurations = 0; - out_unauthorized: usb_unlock_device(usb_dev); return 0; @@ -2458,17 +2537,7 @@ int usb_authorize_device(struct usb_device *usb_dev) goto error_device_descriptor; } - kfree(usb_dev->product); - usb_dev->product = NULL; - kfree(usb_dev->manufacturer); - usb_dev->manufacturer = NULL; - kfree(usb_dev->serial); - usb_dev->serial = NULL; - usb_dev->authorized = 1; - result = usb_enumerate_device(usb_dev); - if (result < 0) - goto error_enumerate; /* Choose and set the configuration. This registers the interfaces * with the driver core and lets interface drivers bind to them. */ @@ -2484,12 +2553,11 @@ int usb_authorize_device(struct usb_device *usb_dev) } dev_info(&usb_dev->dev, "authorized to connect\n"); -error_enumerate: error_device_descriptor: usb_autosuspend_device(usb_dev); error_autoresume: out_authorized: - usb_unlock_device(usb_dev); // complements locktree + usb_unlock_device(usb_dev); /* complements locktree */ return result; } @@ -2517,10 +2585,25 @@ static unsigned hub_is_wusb(struct usb_hub *hub) #define HUB_LONG_RESET_TIME 200 #define HUB_RESET_TIMEOUT 800 +/* + * "New scheme" enumeration causes an extra state transition to be + * exposed to an xhci host and causes USB3 devices to receive control + * commands in the default state. This has been seen to cause + * enumeration failures, so disable this enumeration scheme for USB3 + * devices. + */ +static bool use_new_scheme(struct usb_device *udev, int retry) +{ + if (udev->speed == USB_SPEED_SUPER) + return false; + + return USE_NEW_SCHEME(retry); +} + static int hub_port_reset(struct usb_hub *hub, int port1, struct usb_device *udev, unsigned int delay, bool warm); -/* Is a USB 3.0 port in the Inactive or Complinance Mode state? +/* Is a USB 3.0 port in the Inactive or Compliance Mode state? * Port worm reset is required to recover */ static bool hub_port_warm_reset_required(struct usb_hub *hub, u16 portstatus) @@ -2558,9 +2641,9 @@ static int hub_port_wait_reset(struct usb_hub *hub, int port1, if (delay_time >= 2 * HUB_SHORT_RESET_TIME) delay = HUB_LONG_RESET_TIME; - dev_dbg (hub->intfdev, - "port %d not %sreset yet, waiting %dms\n", - port1, warm ? "warm " : "", delay); + dev_dbg(&hub->ports[port1 - 1]->dev, + "not %sreset yet, waiting %dms\n", + warm ? "warm " : "", delay); } if ((portstatus & USB_PORT_STAT_RESET)) @@ -2644,6 +2727,7 @@ static int hub_port_reset(struct usb_hub *hub, int port1, { int i, status; u16 portchange, portstatus; + struct usb_port *port_dev = hub->ports[port1 - 1]; if (!hub_is_superspeed(hub->hdev)) { if (warm) { @@ -2677,9 +2761,9 @@ static int hub_port_reset(struct usb_hub *hub, int port1, if (status == -ENODEV) { ; /* The hub is gone */ } else if (status) { - dev_err(hub->intfdev, - "cannot %sreset port %d (err = %d)\n", - warm ? "warm " : "", port1, status); + dev_err(&port_dev->dev, + "cannot %sreset (err = %d)\n", + warm ? "warm " : "", status); } else { status = hub_port_wait_reset(hub, port1, udev, delay, warm); @@ -2712,21 +2796,19 @@ static int hub_port_reset(struct usb_hub *hub, int port1, * hot or warm reset failed. Try another warm reset. */ if (!warm) { - dev_dbg(hub->intfdev, "hot reset failed, warm reset port %d\n", - port1); + dev_dbg(&port_dev->dev, + "hot reset failed, warm reset\n"); warm = true; } } - dev_dbg (hub->intfdev, - "port %d not enabled, trying %sreset again...\n", - port1, warm ? "warm " : ""); + dev_dbg(&port_dev->dev, + "not enabled, trying %sreset again...\n", + warm ? "warm " : ""); delay = HUB_LONG_RESET_TIME; } - dev_err (hub->intfdev, - "Cannot enable port %i. Maybe the USB cable is bad?\n", - port1); + dev_err(&port_dev->dev, "Cannot enable. Maybe the USB cable is bad?\n"); done: if (!hub_is_superspeed(hub->hdev)) @@ -2751,6 +2833,20 @@ static int port_is_power_on(struct usb_hub *hub, unsigned portstatus) return ret; } +static void usb_lock_port(struct usb_port *port_dev) + __acquires(&port_dev->status_lock) +{ + mutex_lock(&port_dev->status_lock); + __acquire(&port_dev->status_lock); +} + +static void usb_unlock_port(struct usb_port *port_dev) + __releases(&port_dev->status_lock) +{ + mutex_unlock(&port_dev->status_lock); + __release(&port_dev->status_lock); +} + #ifdef CONFIG_PM /* Check if a port is suspended(USB2.0 port) or in U3 state(USB3.0 port) */ @@ -2777,6 +2873,8 @@ static int check_port_resume_type(struct usb_device *udev, struct usb_hub *hub, int port1, int status, unsigned portchange, unsigned portstatus) { + struct usb_port *port_dev = hub->ports[port1 - 1]; + /* Is the device still present? */ if (status || port_is_suspended(hub, portstatus) || !port_is_power_on(hub, portstatus) || @@ -2796,9 +2894,8 @@ static int check_port_resume_type(struct usb_device *udev, } if (status) { - dev_dbg(hub->intfdev, - "port %d status %04x.%04x after resume, %d\n", - port1, portchange, portstatus, status); + dev_dbg(&port_dev->dev, "status %04x.%04x after resume, %d\n", + portchange, portstatus, status); } else if (udev->reset_resume) { /* Late port handoff can set status-change bits */ @@ -2972,6 +3069,8 @@ int usb_port_suspend(struct usb_device *udev, pm_message_t msg) int status; bool really_suspend = true; + usb_lock_port(port_dev); + /* enable remote wakeup when appropriate; this lets the device * wake up the upstream hub (including maybe the root hub). * @@ -3029,8 +3128,7 @@ int usb_port_suspend(struct usb_device *udev, pm_message_t msg) status = 0; } if (status) { - dev_dbg(hub->intfdev, "can't suspend port %d, status %d\n", - port1, status); + dev_dbg(&port_dev->dev, "can't suspend, status %d\n", status); /* Try to enable USB3 LPM and LTM again */ usb_unlocked_enable_lpm(udev); @@ -3061,12 +3159,13 @@ int usb_port_suspend(struct usb_device *udev, pm_message_t msg) usb_set_device_state(udev, USB_STATE_SUSPENDED); } - if (status == 0 && !udev->do_remote_wakeup && udev->persist_enabled) { + if (status == 0 && !udev->do_remote_wakeup && udev->persist_enabled + && test_and_clear_bit(port1, hub->child_usage_bits)) pm_runtime_put_sync(&port_dev->dev); - port_dev->did_runtime_put = true; - } usb_mark_last_busy(hub->hdev); + + usb_unlock_port(port_dev); return status; } @@ -3104,12 +3203,22 @@ static int finish_port_resume(struct usb_device *udev) * operation is carried out here, after the port has been * resumed. */ - if (udev->reset_resume) + if (udev->reset_resume) { + /* + * If the device morphs or switches modes when it is reset, + * we don't want to perform a reset-resume. We'll fail the + * resume, which will cause a logical disconnect, and then + * the device will be rediscovered. + */ retry_reset_resume: - status = usb_reset_and_verify_device(udev); + if (udev->quirks & USB_QUIRK_RESET) + status = -ENODEV; + else + status = usb_reset_and_verify_device(udev); + } - /* 10.5.4.5 says be sure devices in the tree are still there. - * For now let's assume the device didn't go crazy on resume, + /* 10.5.4.5 says be sure devices in the tree are still there. + * For now let's assume the device didn't go crazy on resume, * and device drivers will know about any resume quirks. */ if (status == 0) { @@ -3196,9 +3305,8 @@ int usb_port_resume(struct usb_device *udev, pm_message_t msg) int status; u16 portchange, portstatus; - if (port_dev->did_runtime_put) { + if (!test_and_set_bit(port1, hub->child_usage_bits)) { status = pm_runtime_get_sync(&port_dev->dev); - port_dev->did_runtime_put = false; if (status < 0) { dev_dbg(&udev->dev, "can't resume usb port, status %d\n", status); @@ -3206,15 +3314,13 @@ int usb_port_resume(struct usb_device *udev, pm_message_t msg) } } + usb_lock_port(port_dev); + /* Skip the initial Clear-Suspend step for a remote wakeup */ status = hub_port_status(hub, port1, &portstatus, &portchange); if (status == 0 && !port_is_suspended(hub, portstatus)) goto SuspendCleared; - // dev_dbg(hub->intfdev, "resume port %d\n", port1); - - set_bit(port1, hub->busy_bits); - /* see 7.1.7.7; affects power usage, but not budgeting */ if (hub_is_superspeed(hub->hdev)) status = hub_set_port_link_state(hub, port1, USB_SS_PORT_LS_U0); @@ -3222,8 +3328,7 @@ int usb_port_resume(struct usb_device *udev, pm_message_t msg) status = usb_clear_port_feature(hub->hdev, port1, USB_PORT_FEAT_SUSPEND); if (status) { - dev_dbg(hub->intfdev, "can't resume port %d, status %d\n", - port1, status); + dev_dbg(&port_dev->dev, "can't resume, status %d\n", status); } else { /* drive resume for at least 20 msec */ dev_dbg(&udev->dev, "usb %sresume\n", @@ -3254,8 +3359,6 @@ int usb_port_resume(struct usb_device *udev, pm_message_t msg) } } - clear_bit(port1, hub->busy_bits); - status = check_port_resume_type(udev, hub, port1, status, portchange, portstatus); if (status == 0) @@ -3273,16 +3376,18 @@ int usb_port_resume(struct usb_device *udev, pm_message_t msg) usb_unlocked_enable_lpm(udev); } + usb_unlock_port(port_dev); + return status; } #ifdef CONFIG_PM_RUNTIME -/* caller has locked udev */ int usb_remote_wakeup(struct usb_device *udev) { int status = 0; + usb_lock_device(udev); if (udev->state == USB_STATE_SUSPENDED) { dev_dbg(&udev->dev, "usb %sresume\n", "wakeup-"); status = usb_autoresume_device(udev); @@ -3291,9 +3396,59 @@ int usb_remote_wakeup(struct usb_device *udev) usb_autosuspend_device(udev); } } + usb_unlock_device(udev); return status; } +/* Returns 1 if there was a remote wakeup and a connect status change. */ +static int hub_handle_remote_wakeup(struct usb_hub *hub, unsigned int port, + u16 portstatus, u16 portchange) + __must_hold(&port_dev->status_lock) +{ + struct usb_port *port_dev = hub->ports[port - 1]; + struct usb_device *hdev; + struct usb_device *udev; + int connect_change = 0; + int ret; + + hdev = hub->hdev; + udev = port_dev->child; + if (!hub_is_superspeed(hdev)) { + if (!(portchange & USB_PORT_STAT_C_SUSPEND)) + return 0; + usb_clear_port_feature(hdev, port, USB_PORT_FEAT_C_SUSPEND); + } else { + if (!udev || udev->state != USB_STATE_SUSPENDED || + (portstatus & USB_PORT_STAT_LINK_STATE) != + USB_SS_PORT_LS_U0) + return 0; + } + + if (udev) { + /* TRSMRCY = 10 msec */ + msleep(10); + + usb_unlock_port(port_dev); + ret = usb_remote_wakeup(udev); + usb_lock_port(port_dev); + if (ret < 0) + connect_change = 1; + } else { + ret = -ENODEV; + hub_port_disable(hub, port, 1); + } + dev_dbg(&port_dev->dev, "resume, status %d\n", ret); + return connect_change; +} + +#else + +static int hub_handle_remote_wakeup(struct usb_hub *hub, unsigned int port, + u16 portstatus, u16 portchange) +{ + return 0; +} + #endif static int check_ports_changed(struct usb_hub *hub) @@ -3324,11 +3479,12 @@ static int hub_suspend(struct usb_interface *intf, pm_message_t msg) */ hub->wakeup_enabled_descendants = 0; for (port1 = 1; port1 <= hdev->maxchild; port1++) { - struct usb_device *udev; + struct usb_port *port_dev = hub->ports[port1 - 1]; + struct usb_device *udev = port_dev->child; - udev = hub->ports[port1 - 1]->child; if (udev && udev->can_submit) { - dev_warn(&intf->dev, "port %d nyet suspended\n", port1); + dev_warn(&port_dev->dev, "device %s not suspended yet\n", + dev_name(&udev->dev)); if (PMSG_IS_AUTO(msg)) return -EBUSY; } @@ -3847,6 +4003,12 @@ EXPORT_SYMBOL_GPL(usb_disable_ltm); void usb_enable_ltm(struct usb_device *udev) { } EXPORT_SYMBOL_GPL(usb_enable_ltm); +static int hub_handle_remote_wakeup(struct usb_hub *hub, unsigned int port, + u16 portstatus, u16 portchange) +{ + return 0; +} + #endif /* CONFIG_PM */ @@ -3855,7 +4017,7 @@ EXPORT_SYMBOL_GPL(usb_enable_ltm); * Between connect detection and reset signaling there must be a delay * of 100ms at least for debounce and power-settling. The corresponding * timer shall restart whenever the downstream port detects a disconnect. - * + * * Apparently there are some bluetooth and irda-dongles and a number of * low-speed devices for which this debounce period may last over a second. * Not covered by the spec - but easy to deal with. @@ -3868,9 +4030,10 @@ EXPORT_SYMBOL_GPL(usb_enable_ltm); int hub_port_debounce(struct usb_hub *hub, int port1, bool must_be_connected) { int ret; - int total_time, stable_time = 0; u16 portchange, portstatus; unsigned connection = 0xffff; + int total_time, stable_time = 0; + struct usb_port *port_dev = hub->ports[port1 - 1]; for (total_time = 0; ; total_time += HUB_DEBOUNCE_STEP) { ret = hub_port_status(hub, port1, &portstatus, &portchange); @@ -3899,9 +4062,8 @@ int hub_port_debounce(struct usb_hub *hub, int port1, bool must_be_connected) msleep(HUB_DEBOUNCE_STEP); } - dev_dbg (hub->intfdev, - "debounce: port %d: total %dms stable %dms status 0x%x\n", - port1, total_time, stable_time, portstatus); + dev_dbg(&port_dev->dev, "debounce total %dms stable %dms status 0x%x\n", + total_time, stable_time, portstatus); if (stable_time < HUB_DEBOUNCE_STABLE) return -ETIMEDOUT; @@ -3949,21 +4111,61 @@ static int hub_set_address(struct usb_device *udev, int devnum) return retval; } +/* + * There are reports of USB 3.0 devices that say they support USB 2.0 Link PM + * when they're plugged into a USB 2.0 port, but they don't work when LPM is + * enabled. + * + * Only enable USB 2.0 Link PM if the port is internal (hardwired), or the + * device says it supports the new USB 2.0 Link PM errata by setting the BESL + * support bit in the BOS descriptor. + */ +static void hub_set_initial_usb2_lpm_policy(struct usb_device *udev) +{ + struct usb_hub *hub = usb_hub_to_struct_hub(udev->parent); + int connect_type = USB_PORT_CONNECT_TYPE_UNKNOWN; + + if (!udev->usb2_hw_lpm_capable) + return; + + if (hub) + connect_type = hub->ports[udev->portnum - 1]->connect_type; + + if ((udev->bos->ext_cap->bmAttributes & cpu_to_le32(USB_BESL_SUPPORT)) || + connect_type == USB_PORT_CONNECT_TYPE_HARD_WIRED) { + udev->usb2_hw_lpm_allowed = 1; + usb_set_usb2_hardware_lpm(udev, 1); + } +} + +static int hub_enable_device(struct usb_device *udev) +{ + struct usb_hcd *hcd = bus_to_hcd(udev->bus); + + if (!hcd->driver->enable_device) + return 0; + if (udev->state == USB_STATE_ADDRESS) + return 0; + if (udev->state != USB_STATE_DEFAULT) + return -EINVAL; + + return hcd->driver->enable_device(hcd, udev); +} + /* Reset device, (re)assign address, get device descriptor. * Device connection must be stable, no more debouncing needed. * Returns device in USB_STATE_ADDRESS, except on error. * * If this is called for an already-existing device (as part of - * usb_reset_and_verify_device), the caller must own the device lock. For a - * newly detected device that is not accessible through any global - * pointers, it's not necessary to lock the device. + * usb_reset_and_verify_device), the caller must own the device lock and + * the port lock. For a newly detected device that is not accessible + * through any global pointers, it's not necessary to lock the device, + * but it is still necessary to lock the port. */ static int hub_port_init (struct usb_hub *hub, struct usb_device *udev, int port1, int retry_counter) { - static DEFINE_MUTEX(usb_address0_mutex); - struct usb_device *hdev = hub->hdev; struct usb_hcd *hcd = bus_to_hcd(hdev->bus); int i, j, retval; @@ -3986,7 +4188,7 @@ hub_port_init (struct usb_hub *hub, struct usb_device *udev, int port1, if (oldspeed == USB_SPEED_LOW) delay = HUB_LONG_RESET_TIME; - mutex_lock(&usb_address0_mutex); + mutex_lock(&hdev->bus->usb_address0_mutex); /* Reset the device; full speed may morph to high speed */ /* FIXME a USB 2.0 device may morph into SuperSpeed on reset. */ @@ -4055,13 +4257,13 @@ hub_port_init (struct usb_hub *hub, struct usb_device *udev, int port1, udev->tt = &hub->tt; udev->ttport = port1; } - + /* Why interleave GET_DESCRIPTOR and SET_ADDRESS this way? * Because device hardware and firmware is sometimes buggy in * this area, and this is how Linux has done it for ages. * Change it cautiously. * - * NOTE: If USE_NEW_SCHEME() is true we will start by issuing + * NOTE: If use_new_scheme() is true we will start by issuing * a 64-byte GET_DESCRIPTOR request. This is what Windows does, * so it may help with some non-standards-compliant devices. * Otherwise we start with SET_ADDRESS and then try to read the @@ -4069,10 +4271,21 @@ hub_port_init (struct usb_hub *hub, struct usb_device *udev, int port1, * value. */ for (i = 0; i < GET_DESCRIPTOR_TRIES; (++i, msleep(100))) { - if (USE_NEW_SCHEME(retry_counter) && !(hcd->driver->flags & HCD_USB3)) { + bool did_new_scheme = false; + + if (use_new_scheme(udev, retry_counter)) { struct usb_device_descriptor *buf; int r = 0; + did_new_scheme = true; + retval = hub_enable_device(udev); + if (retval < 0) { + dev_err(&udev->dev, + "hub failed to enable device, error %d\n", + retval); + goto fail; + } + #define GET_DESCRIPTOR_BUFSIZE 64 buf = kmalloc(GET_DESCRIPTOR_BUFSIZE, GFP_NOIO); if (!buf) { @@ -4130,11 +4343,11 @@ hub_port_init (struct usb_hub *hub, struct usb_device *udev, int port1, #undef GET_DESCRIPTOR_BUFSIZE } - /* - * If device is WUSB, we already assigned an - * unauthorized address in the Connect Ack sequence; - * authorization will assign the final address. - */ + /* + * If device is WUSB, we already assigned an + * unauthorized address in the Connect Ack sequence; + * authorization will assign the final address. + */ if (udev->wusb == 0) { for (j = 0; j < SET_ADDRESS_TRIES; ++j) { retval = hub_set_address(udev, devnum); @@ -4161,9 +4374,13 @@ hub_port_init (struct usb_hub *hub, struct usb_device *udev, int port1, * - read ep0 maxpacket even for high and low speed, */ msleep(10); - if (USE_NEW_SCHEME(retry_counter) && !(hcd->driver->flags & HCD_USB3)) + /* use_new_scheme() checks the speed which may have + * changed since the initial look so we cache the result + * in did_new_scheme + */ + if (did_new_scheme) break; - } + } retval = usb_get_device_descriptor(udev, 8); if (retval < 8) { @@ -4219,7 +4436,7 @@ hub_port_init (struct usb_hub *hub, struct usb_device *udev, int port1, udev->ep0.desc.wMaxPacketSize = cpu_to_le16(i); usb_ep0_reinit(udev); } - + retval = usb_get_device_descriptor(udev, USB_DT_DEVICE_SIZE); if (retval < (signed)sizeof(udev->descriptor)) { if (retval != -ENODEV) @@ -4242,12 +4459,13 @@ hub_port_init (struct usb_hub *hub, struct usb_device *udev, int port1, /* notify HCD that we have a device connected and addressed */ if (hcd->driver->update_device) hcd->driver->update_device(hcd, udev); + hub_set_initial_usb2_lpm_policy(udev); fail: if (retval) { hub_port_disable(hub, port1, 0); update_devnum(udev, devnum); /* for disconnect processing */ } - mutex_unlock(&usb_address0_mutex); + mutex_unlock(&hdev->bus->usb_address0_mutex); return retval; } @@ -4269,7 +4487,8 @@ check_highspeed (struct usb_hub *hub, struct usb_device *udev, int port1) /* hub LEDs are probably harder to miss than syslog */ if (hub->has_indicators) { hub->indicator[port1-1] = INDICATOR_GREEN_BLINK; - schedule_delayed_work (&hub->leds, 0); + queue_delayed_work(system_power_efficient_wq, + &hub->leds, 0); } } kfree(qual); @@ -4287,9 +4506,10 @@ hub_power_remaining (struct usb_hub *hub) remaining = hdev->bus_mA - hub->descriptor->bHubContrCurrent; for (port1 = 1; port1 <= hdev->maxchild; ++port1) { - struct usb_device *udev = hub->ports[port1 - 1]->child; - int delta; - unsigned unit_load; + struct usb_port *port_dev = hub->ports[port1 - 1]; + struct usb_device *udev = port_dev->child; + unsigned unit_load; + int delta; if (!udev) continue; @@ -4309,91 +4529,35 @@ hub_power_remaining (struct usb_hub *hub) else delta = 8; if (delta > hub->mA_per_port) - dev_warn(&udev->dev, - "%dmA is over %umA budget for port %d!\n", - delta, hub->mA_per_port, port1); + dev_warn(&port_dev->dev, "%dmA is over %umA budget!\n", + delta, hub->mA_per_port); remaining -= delta; } if (remaining < 0) { dev_warn(hub->intfdev, "%dmA over power budget!\n", - - remaining); + -remaining); remaining = 0; } return remaining; } -/* Handle physical or logical connection change events. - * This routine is called when: - * a port connection-change occurs; - * a port enable-change occurs (often caused by EMI); - * usb_reset_and_verify_device() encounters changed descriptors (as from - * a firmware download) - * caller already locked the hub - */ -static void hub_port_connect_change(struct usb_hub *hub, int port1, - u16 portstatus, u16 portchange) +static void hub_port_connect(struct usb_hub *hub, int port1, u16 portstatus, + u16 portchange) { - struct usb_device *hdev = hub->hdev; - struct device *hub_dev = hub->intfdev; - struct usb_hcd *hcd = bus_to_hcd(hdev->bus); - unsigned wHubCharacteristics = - le16_to_cpu(hub->descriptor->wHubCharacteristics); - struct usb_device *udev; int status, i; unsigned unit_load; - - dev_dbg (hub_dev, - "port %d, status %04x, change %04x, %s\n", - port1, portstatus, portchange, portspeed(hub, portstatus)); - - if (hub->has_indicators) { - set_port_led(hub, port1, HUB_LED_AUTO); - hub->indicator[port1-1] = INDICATOR_AUTO; - } - -#ifdef CONFIG_USB_OTG - /* during HNP, don't repeat the debounce */ - if (hdev->bus->is_b_host) - portchange &= ~(USB_PORT_STAT_C_CONNECTION | - USB_PORT_STAT_C_ENABLE); -#endif - - /* Try to resuscitate an existing device */ - udev = hub->ports[port1 - 1]->child; - if ((portstatus & USB_PORT_STAT_CONNECTION) && udev && - udev->state != USB_STATE_NOTATTACHED) { - usb_lock_device(udev); - if (portstatus & USB_PORT_STAT_ENABLE) { - status = 0; /* Nothing to do */ - -#ifdef CONFIG_PM_RUNTIME - } else if (udev->state == USB_STATE_SUSPENDED && - udev->persist_enabled) { - /* For a suspended device, treat this as a - * remote wakeup event. - */ - status = usb_remote_wakeup(udev); -#endif - - } else { - status = -ENODEV; /* Don't resuscitate */ - } - usb_unlock_device(udev); - - if (status == 0) { - clear_bit(port1, hub->change_bits); - return; - } - } + struct usb_device *hdev = hub->hdev; + struct usb_hcd *hcd = bus_to_hcd(hdev->bus); + struct usb_port *port_dev = hub->ports[port1 - 1]; + struct usb_device *udev = port_dev->child; /* Disconnect any existing devices under this port */ if (udev) { if (hcd->phy && !hdev->parent && !(portstatus & USB_PORT_STAT_CONNECTION)) usb_phy_notify_disconnect(hcd->phy, udev->speed); - usb_disconnect(&hub->ports[port1 - 1]->child); + usb_disconnect(&port_dev->child); } - clear_bit(port1, hub->change_bits); /* We can forget about a "removed" device when there's a physical * disconnect or the connect status changes. @@ -4407,8 +4571,8 @@ static void hub_port_connect_change(struct usb_hub *hub, int port1, status = hub_port_debounce_be_stable(hub, port1); if (status < 0) { if (status != -ENODEV && printk_ratelimit()) - dev_err(hub_dev, "connect-debounce failed, " - "port %d disabled\n", port1); + dev_err(&port_dev->dev, + "connect-debounce failed\n"); portstatus &= ~USB_PORT_STAT_CONNECTION; } else { portstatus = status; @@ -4422,12 +4586,12 @@ static void hub_port_connect_change(struct usb_hub *hub, int port1, test_bit(port1, hub->removed_bits)) { /* maybe switch power back on (e.g. root hub was reset) */ - if ((wHubCharacteristics & HUB_CHAR_LPSM) < 2 + if (hub_is_port_power_switchable(hub) && !port_is_power_on(hub, portstatus)) set_port_feature(hdev, port1, USB_PORT_FEAT_POWER); if (portstatus & USB_PORT_STAT_ENABLE) - goto done; + goto done; return; } if (hub_is_superspeed(hub->hdev)) @@ -4443,14 +4607,13 @@ static void hub_port_connect_change(struct usb_hub *hub, int port1, */ udev = usb_alloc_dev(hdev, hdev->bus, port1); if (!udev) { - dev_err (hub_dev, - "couldn't allocate port %d usb_device\n", - port1); + dev_err(&port_dev->dev, + "couldn't allocate usb_device\n"); goto done; } usb_set_device_state(udev, USB_STATE_POWERED); - udev->bus_mA = hub->mA_per_port; + udev->bus_mA = hub->mA_per_port; udev->level = hdev->level + 1; udev->wusb = hub_is_wusb(hub); @@ -4467,7 +4630,9 @@ static void hub_port_connect_change(struct usb_hub *hub, int port1, } /* reset (non-USB 3.0 devices) and get descriptor */ + usb_lock_port(port_dev); status = hub_port_init(hub, udev, port1, i); + usb_unlock_port(port_dev); if (status < 0) goto loop; @@ -4498,13 +4663,15 @@ static void hub_port_connect_change(struct usb_hub *hub, int port1, if (hub->has_indicators) { hub->indicator[port1-1] = INDICATOR_AMBER_BLINK; - schedule_delayed_work (&hub->leds, 0); + queue_delayed_work( + system_power_efficient_wq, + &hub->leds, 0); } status = -ENOTCONN; /* Don't retry */ goto loop_disable; } } - + /* check for devices running slower than they could */ if (le16_to_cpu(udev->descriptor.bcdUSB) >= 0x0200 && udev->speed == USB_SPEED_FULL @@ -4517,6 +4684,8 @@ static void hub_port_connect_change(struct usb_hub *hub, int port1, */ status = 0; + mutex_lock(&usb_port_peer_mutex); + /* We mustn't add new devices if the parent hub has * been disconnected; we would race with the * recursively_mark_NOTATTACHED() routine. @@ -4525,16 +4694,19 @@ static void hub_port_connect_change(struct usb_hub *hub, int port1, if (hdev->state == USB_STATE_NOTATTACHED) status = -ENOTCONN; else - hub->ports[port1 - 1]->child = udev; + port_dev->child = udev; spin_unlock_irq(&device_state_lock); + mutex_unlock(&usb_port_peer_mutex); /* Run it through the hoops (find a driver, etc) */ if (!status) { status = usb_new_device(udev); if (status) { + mutex_lock(&usb_port_peer_mutex); spin_lock_irq(&device_state_lock); - hub->ports[port1 - 1]->child = NULL; + port_dev->child = NULL; spin_unlock_irq(&device_state_lock); + mutex_unlock(&usb_port_peer_mutex); } } @@ -4543,7 +4715,7 @@ static void hub_port_connect_change(struct usb_hub *hub, int port1, status = hub_power_remaining(hub); if (status) - dev_dbg(hub_dev, "%dmA power budget left\n", status); + dev_dbg(hub->intfdev, "%dmA power budget left\n", status); return; @@ -4561,56 +4733,200 @@ loop: !hcd->driver->port_handed_over || !(hcd->driver->port_handed_over)(hcd, port1)) { if (status != -ENOTCONN && status != -ENODEV) - dev_err(hub_dev, "unable to enumerate USB device on port %d\n", - port1); + dev_err(&port_dev->dev, + "unable to enumerate USB device\n"); } - + done: hub_port_disable(hub, port1, 1); if (hcd->driver->relinquish_port && !hub->hdev->parent) hcd->driver->relinquish_port(hcd, port1); + } -/* Returns 1 if there was a remote wakeup and a connect status change. */ -static int hub_handle_remote_wakeup(struct usb_hub *hub, unsigned int port, - u16 portstatus, u16 portchange) +/* Handle physical or logical connection change events. + * This routine is called when: + * a port connection-change occurs; + * a port enable-change occurs (often caused by EMI); + * usb_reset_and_verify_device() encounters changed descriptors (as from + * a firmware download) + * caller already locked the hub + */ +static void hub_port_connect_change(struct usb_hub *hub, int port1, + u16 portstatus, u16 portchange) + __must_hold(&port_dev->status_lock) { - struct usb_device *hdev; - struct usb_device *udev; - int connect_change = 0; - int ret; + struct usb_port *port_dev = hub->ports[port1 - 1]; + struct usb_device *udev = port_dev->child; + int status = -ENODEV; - hdev = hub->hdev; - udev = hub->ports[port - 1]->child; - if (!hub_is_superspeed(hdev)) { - if (!(portchange & USB_PORT_STAT_C_SUSPEND)) - return 0; - usb_clear_port_feature(hdev, port, USB_PORT_FEAT_C_SUSPEND); - } else { - if (!udev || udev->state != USB_STATE_SUSPENDED || - (portstatus & USB_PORT_STAT_LINK_STATE) != - USB_SS_PORT_LS_U0) - return 0; + dev_dbg(&port_dev->dev, "status %04x, change %04x, %s\n", portstatus, + portchange, portspeed(hub, portstatus)); + + if (hub->has_indicators) { + set_port_led(hub, port1, HUB_LED_AUTO); + hub->indicator[port1-1] = INDICATOR_AUTO; } - if (udev) { - /* TRSMRCY = 10 msec */ - msleep(10); +#ifdef CONFIG_USB_OTG + /* during HNP, don't repeat the debounce */ + if (hub->hdev->bus->is_b_host) + portchange &= ~(USB_PORT_STAT_C_CONNECTION | + USB_PORT_STAT_C_ENABLE); +#endif + /* Try to resuscitate an existing device */ + if ((portstatus & USB_PORT_STAT_CONNECTION) && udev && + udev->state != USB_STATE_NOTATTACHED) { + if (portstatus & USB_PORT_STAT_ENABLE) { + status = 0; /* Nothing to do */ +#ifdef CONFIG_PM_RUNTIME + } else if (udev->state == USB_STATE_SUSPENDED && + udev->persist_enabled) { + /* For a suspended device, treat this as a + * remote wakeup event. + */ + usb_unlock_port(port_dev); + status = usb_remote_wakeup(udev); + usb_lock_port(port_dev); +#endif + } else { + /* Don't resuscitate */; + } + } + clear_bit(port1, hub->change_bits); + + /* successfully revalidated the connection */ + if (status == 0) + return; + + usb_unlock_port(port_dev); + hub_port_connect(hub, port1, portstatus, portchange); + usb_lock_port(port_dev); +} + +static void port_event(struct usb_hub *hub, int port1) + __must_hold(&port_dev->status_lock) +{ + int connect_change, reset_device = 0; + struct usb_port *port_dev = hub->ports[port1 - 1]; + struct usb_device *udev = port_dev->child; + struct usb_device *hdev = hub->hdev; + u16 portstatus, portchange; + + connect_change = test_bit(port1, hub->change_bits); + clear_bit(port1, hub->event_bits); + clear_bit(port1, hub->wakeup_bits); + + if (hub_port_status(hub, port1, &portstatus, &portchange) < 0) + return; + + if (portchange & USB_PORT_STAT_C_CONNECTION) { + usb_clear_port_feature(hdev, port1, USB_PORT_FEAT_C_CONNECTION); + connect_change = 1; + } + + if (portchange & USB_PORT_STAT_C_ENABLE) { + if (!connect_change) + dev_dbg(&port_dev->dev, "enable change, status %08x\n", + portstatus); + usb_clear_port_feature(hdev, port1, USB_PORT_FEAT_C_ENABLE); + + /* + * EM interference sometimes causes badly shielded USB devices + * to be shutdown by the hub, this hack enables them again. + * Works at least with mouse driver. + */ + if (!(portstatus & USB_PORT_STAT_ENABLE) + && !connect_change && udev) { + dev_err(&port_dev->dev, "disabled by hub (EMI?), re-enabling...\n"); + connect_change = 1; + } + } + + if (portchange & USB_PORT_STAT_C_OVERCURRENT) { + u16 status = 0, unused; + + dev_dbg(&port_dev->dev, "over-current change\n"); + usb_clear_port_feature(hdev, port1, + USB_PORT_FEAT_C_OVER_CURRENT); + msleep(100); /* Cool down */ + hub_power_on(hub, true); + hub_port_status(hub, port1, &status, &unused); + if (status & USB_PORT_STAT_OVERCURRENT) + dev_err(&port_dev->dev, "over-current condition\n"); + } + + if (portchange & USB_PORT_STAT_C_RESET) { + dev_dbg(&port_dev->dev, "reset change\n"); + usb_clear_port_feature(hdev, port1, USB_PORT_FEAT_C_RESET); + } + if ((portchange & USB_PORT_STAT_C_BH_RESET) + && hub_is_superspeed(hdev)) { + dev_dbg(&port_dev->dev, "warm reset change\n"); + usb_clear_port_feature(hdev, port1, + USB_PORT_FEAT_C_BH_PORT_RESET); + } + if (portchange & USB_PORT_STAT_C_LINK_STATE) { + dev_dbg(&port_dev->dev, "link state change\n"); + usb_clear_port_feature(hdev, port1, + USB_PORT_FEAT_C_PORT_LINK_STATE); + } + if (portchange & USB_PORT_STAT_C_CONFIG_ERROR) { + dev_warn(&port_dev->dev, "config error\n"); + usb_clear_port_feature(hdev, port1, + USB_PORT_FEAT_C_PORT_CONFIG_ERROR); + } + + /* skip port actions that require the port to be powered on */ + if (!pm_runtime_active(&port_dev->dev)) + return; + + if (hub_handle_remote_wakeup(hub, port1, portstatus, portchange)) + connect_change = 1; + + /* + * Warm reset a USB3 protocol port if it's in + * SS.Inactive state. + */ + if (hub_port_warm_reset_required(hub, portstatus)) { + dev_dbg(&port_dev->dev, "do warm reset\n"); + if (!udev || !(portstatus & USB_PORT_STAT_CONNECTION) + || udev->state == USB_STATE_NOTATTACHED) { + if (hub_port_reset(hub, port1, NULL, + HUB_BH_RESET_TIME, true) < 0) + hub_port_disable(hub, port1, 1); + } else + reset_device = 1; + } + + /* + * On disconnect USB3 protocol ports transit from U0 to + * SS.Inactive to Rx.Detect. If this happens a warm- + * reset is not needed, but a (re)connect may happen + * before khubd runs and sees the disconnect, and the + * device may be an unknown state. + * + * If the port went through SS.Inactive without khubd + * seeing it the C_LINK_STATE change flag will be set, + * and we reset the dev to put it in a known state. + */ + if (reset_device || (udev && hub_is_superspeed(hub->hdev) + && (portchange & USB_PORT_STAT_C_LINK_STATE) + && (portstatus & USB_PORT_STAT_CONNECTION))) { + usb_unlock_port(port_dev); usb_lock_device(udev); - ret = usb_remote_wakeup(udev); + usb_reset_device(udev); usb_unlock_device(udev); - if (ret < 0) - connect_change = 1; - } else { - ret = -ENODEV; - hub_port_disable(hub, port, 1); + usb_lock_port(port_dev); + connect_change = 0; } - dev_dbg(hub->intfdev, "resume on port %d, status %d\n", - port, ret); - return connect_change; + + if (connect_change) + hub_port_connect_change(hub, port1, portstatus, portchange); } + static void hub_events(void) { struct list_head *tmp; @@ -4620,10 +4936,7 @@ static void hub_events(void) struct device *hub_dev; u16 hubstatus; u16 hubchange; - u16 portstatus; - u16 portchange; int i, ret; - int connect_change, wakeup_change; /* * We restart the list every time to avoid a deadlock with @@ -4697,127 +5010,28 @@ static void hub_events(void) /* deal with port status changes */ for (i = 1; i <= hdev->maxchild; i++) { - if (test_bit(i, hub->busy_bits)) - continue; - connect_change = test_bit(i, hub->change_bits); - wakeup_change = test_and_clear_bit(i, hub->wakeup_bits); - if (!test_and_clear_bit(i, hub->event_bits) && - !connect_change && !wakeup_change) - continue; - - ret = hub_port_status(hub, i, - &portstatus, &portchange); - if (ret < 0) - continue; - - if (portchange & USB_PORT_STAT_C_CONNECTION) { - usb_clear_port_feature(hdev, i, - USB_PORT_FEAT_C_CONNECTION); - connect_change = 1; - } - - if (portchange & USB_PORT_STAT_C_ENABLE) { - if (!connect_change) - dev_dbg (hub_dev, - "port %d enable change, " - "status %08x\n", - i, portstatus); - usb_clear_port_feature(hdev, i, - USB_PORT_FEAT_C_ENABLE); + struct usb_port *port_dev = hub->ports[i - 1]; + if (test_bit(i, hub->event_bits) + || test_bit(i, hub->change_bits) + || test_bit(i, hub->wakeup_bits)) { /* - * EM interference sometimes causes badly - * shielded USB devices to be shutdown by - * the hub, this hack enables them again. - * Works at least with mouse driver. + * The get_noresume and barrier ensure that if + * the port was in the process of resuming, we + * flush that work and keep the port active for + * the duration of the port_event(). However, + * if the port is runtime pm suspended + * (powered-off), we leave it in that state, run + * an abbreviated port_event(), and move on. */ - if (!(portstatus & USB_PORT_STAT_ENABLE) - && !connect_change - && hub->ports[i - 1]->child) { - dev_err (hub_dev, - "port %i " - "disabled by hub (EMI?), " - "re-enabling...\n", - i); - connect_change = 1; - } - } - - if (hub_handle_remote_wakeup(hub, i, - portstatus, portchange)) - connect_change = 1; - - if (portchange & USB_PORT_STAT_C_OVERCURRENT) { - u16 status = 0; - u16 unused; - - dev_dbg(hub_dev, "over-current change on port " - "%d\n", i); - usb_clear_port_feature(hdev, i, - USB_PORT_FEAT_C_OVER_CURRENT); - msleep(100); /* Cool down */ - hub_power_on(hub, true); - hub_port_status(hub, i, &status, &unused); - if (status & USB_PORT_STAT_OVERCURRENT) - dev_err(hub_dev, "over-current " - "condition on port %d\n", i); - } - - if (portchange & USB_PORT_STAT_C_RESET) { - dev_dbg (hub_dev, - "reset change on port %d\n", - i); - usb_clear_port_feature(hdev, i, - USB_PORT_FEAT_C_RESET); - } - if ((portchange & USB_PORT_STAT_C_BH_RESET) && - hub_is_superspeed(hub->hdev)) { - dev_dbg(hub_dev, - "warm reset change on port %d\n", - i); - usb_clear_port_feature(hdev, i, - USB_PORT_FEAT_C_BH_PORT_RESET); + pm_runtime_get_noresume(&port_dev->dev); + pm_runtime_barrier(&port_dev->dev); + usb_lock_port(port_dev); + port_event(hub, i); + usb_unlock_port(port_dev); + pm_runtime_put_sync(&port_dev->dev); } - if (portchange & USB_PORT_STAT_C_LINK_STATE) { - usb_clear_port_feature(hub->hdev, i, - USB_PORT_FEAT_C_PORT_LINK_STATE); - } - if (portchange & USB_PORT_STAT_C_CONFIG_ERROR) { - dev_warn(hub_dev, - "config error on port %d\n", - i); - usb_clear_port_feature(hub->hdev, i, - USB_PORT_FEAT_C_PORT_CONFIG_ERROR); - } - - /* Warm reset a USB3 protocol port if it's in - * SS.Inactive state. - */ - if (hub_port_warm_reset_required(hub, portstatus)) { - int status; - struct usb_device *udev = - hub->ports[i - 1]->child; - - dev_dbg(hub_dev, "warm reset port %d\n", i); - if (!udev || !(portstatus & - USB_PORT_STAT_CONNECTION)) { - status = hub_port_reset(hub, i, - NULL, HUB_BH_RESET_TIME, - true); - if (status < 0) - hub_port_disable(hub, i, 1); - } else { - usb_lock_device(udev); - status = usb_reset_device(udev); - usb_unlock_device(udev); - connect_change = 0; - } - } - - if (connect_change) - hub_port_connect_change(hub, i, - portstatus, portchange); - } /* end for i */ + } /* deal with hub status changes */ if (test_and_clear_bit(0, hub->event_bits) == 0) @@ -4841,7 +5055,7 @@ static void hub_events(void) dev_dbg(hub_dev, "over-current change\n"); clear_hub_feature(hdev, C_HUB_OVER_CURRENT); msleep(500); /* Cool down */ - hub_power_on(hub, true); + hub_power_on(hub, true); hub_hub_status(hub, &status, &unused); if (status & HUB_STATUS_OVERCURRENT) dev_err(hub_dev, "over-current " @@ -4861,12 +5075,12 @@ static void hub_events(void) usb_unlock_device(hdev); kref_put(&hub->kref, hub_release); - } /* end while (1) */ + } /* end while (1) */ } static int hub_thread(void *__unused) { - /* khubd needs to be freezable to avoid intefering with USB-PERSIST + /* khubd needs to be freezable to avoid interfering with USB-PERSIST * port handover. Otherwise it might see that a full-speed device * was gone before the EHCI controller had handed its port over to * the companion full-speed controller. @@ -4886,7 +5100,7 @@ static int hub_thread(void *__unused) static const struct usb_device_id hub_id_table[] = { { .match_flags = USB_DEVICE_ID_MATCH_VENDOR - | USB_DEVICE_ID_MATCH_INT_CLASS, + | USB_DEVICE_ID_MATCH_INT_CLASS, .idVendor = USB_VENDOR_GENESYS_LOGIC, .bInterfaceClass = USB_CLASS_HUB, .driver_info = HUB_QUIRK_CHECK_PORT_AUTOSUSPEND}, @@ -5052,15 +5266,18 @@ static int descriptors_changed(struct usb_device *udev, * if the reset wasn't even attempted. * * Note: - * The caller must own the device lock. For example, it's safe to use - * this from a driver probe() routine after downloading new firmware. - * For calls that might not occur during probe(), drivers should lock - * the device using usb_lock_device_for_reset(). + * The caller must own the device lock and the port lock, the latter is + * taken by usb_reset_device(). For example, it's safe to use + * usb_reset_device() from a driver probe() routine after downloading + * new firmware. For calls that might not occur during probe(), drivers + * should lock the device using usb_lock_device_for_reset(). * * Locking exception: This routine may also be called from within an * autoresume handler. Such usage won't conflict with other tasks * holding the device lock because these tasks should always call - * usb_autopm_resume_device(), thereby preventing any unwanted autoresume. + * usb_autopm_resume_device(), thereby preventing any unwanted + * autoresume. The autoresume handler is expected to have already + * acquired the port lock before calling this routine. */ static int usb_reset_and_verify_device(struct usb_device *udev) { @@ -5069,7 +5286,7 @@ static int usb_reset_and_verify_device(struct usb_device *udev) struct usb_hcd *hcd = bus_to_hcd(udev->bus); struct usb_device_descriptor descriptor = udev->descriptor; struct usb_host_bos *bos; - int i, ret = 0; + int i, j, ret = 0; int port1 = udev->portnum; if (udev->state == USB_STATE_NOTATTACHED || @@ -5079,13 +5296,17 @@ static int usb_reset_and_verify_device(struct usb_device *udev) return -EINVAL; } - if (!parent_hdev) { - /* this requires hcd-specific logic; see ohci_restart() */ - dev_dbg(&udev->dev, "%s for root hub!\n", __func__); + if (!parent_hdev) return -EISDIR; - } + parent_hub = usb_hub_to_struct_hub(parent_hdev); + /* Disable USB2 hardware LPM. + * It will be re-enabled by the enumeration process. + */ + if (udev->usb2_hw_lpm_enabled == 1) + usb_set_usb2_hardware_lpm(udev, 0); + bos = udev->bos; udev->bos = NULL; @@ -5106,7 +5327,6 @@ static int usb_reset_and_verify_device(struct usb_device *udev) goto re_enumerate; } - set_bit(port1, parent_hub->busy_bits); for (i = 0; i < SET_CONFIG_TRIES; ++i) { /* ep0 maxpacket size may change; let the HCD know about it. @@ -5116,17 +5336,16 @@ static int usb_reset_and_verify_device(struct usb_device *udev) if (ret >= 0 || ret == -ENOTCONN || ret == -ENODEV) break; } - clear_bit(port1, parent_hub->busy_bits); if (ret < 0) goto re_enumerate; - + /* Device might have changed firmware (DFU or similar) */ if (descriptors_changed(udev, &descriptor, bos)) { dev_info(&udev->dev, "device firmware changed\n"); udev->descriptor = descriptor; /* for disconnect() calls */ goto re_enumerate; - } + } /* Restore the device's previous configuration */ if (!udev->actconfig) @@ -5151,7 +5370,7 @@ static int usb_reset_and_verify_device(struct usb_device *udev) udev->actconfig->desc.bConfigurationValue, ret); mutex_unlock(hcd->bandwidth_mutex); goto re_enumerate; - } + } mutex_unlock(hcd->bandwidth_mutex); usb_set_device_state(udev, USB_STATE_CONFIGURED); @@ -5189,16 +5408,20 @@ static int usb_reset_and_verify_device(struct usb_device *udev) ret); goto re_enumerate; } + /* Resetting also frees any allocated streams */ + for (j = 0; j < intf->cur_altsetting->desc.bNumEndpoints; j++) + intf->cur_altsetting->endpoint[j].streams = 0; } done: /* Now that the alt settings are re-installed, enable LTM and LPM. */ + usb_set_usb2_hardware_lpm(udev, 1); usb_unlocked_enable_lpm(udev); usb_enable_ltm(udev); usb_release_bos_descriptor(udev); udev->bos = bos; return 0; - + re_enumerate: /* LPM state doesn't matter when we're about to destroy the device. */ hub_port_logical_disconnect(parent_hub, port1); @@ -5233,7 +5456,9 @@ int usb_reset_device(struct usb_device *udev) int ret; int i; unsigned int noio_flag; + struct usb_port *port_dev; struct usb_host_config *config = udev->actconfig; + struct usb_hub *hub = usb_hub_to_struct_hub(udev->parent); if (udev->state == USB_STATE_NOTATTACHED || udev->state == USB_STATE_SUSPENDED) { @@ -5242,6 +5467,14 @@ int usb_reset_device(struct usb_device *udev) return -EINVAL; } + if (!udev->parent) { + /* this requires hcd-specific logic; see ohci_restart() */ + dev_dbg(&udev->dev, "%s for root hub!\n", __func__); + return -EISDIR; + } + + port_dev = hub->ports[udev->portnum - 1]; + /* * Don't allocate memory with GFP_KERNEL in current * context to avoid possible deadlock if usb mass @@ -5275,7 +5508,9 @@ int usb_reset_device(struct usb_device *udev) } } + usb_lock_port(port_dev); ret = usb_reset_and_verify_device(udev); + usb_unlock_port(port_dev); if (config) { for (i = config->desc.bNumInterfaces - 1; i >= 0; --i) { @@ -5290,10 +5525,11 @@ int usb_reset_device(struct usb_device *udev) else if (cintf->condition == USB_INTERFACE_BOUND) rebind = 1; + if (rebind) + cintf->needs_binding = 1; } - if (ret == 0 && rebind) - usb_rebind_intf(cintf); } + usb_unbind_and_rebind_marked_interfaces(udev); } usb_autosuspend_device(udev); @@ -5369,56 +5605,26 @@ struct usb_device *usb_hub_find_child(struct usb_device *hdev, } EXPORT_SYMBOL_GPL(usb_hub_find_child); -/** - * usb_set_hub_port_connect_type - set hub port connect type. - * @hdev: USB device belonging to the usb hub - * @port1: port num of the port - * @type: connect type of the port - */ -void usb_set_hub_port_connect_type(struct usb_device *hdev, int port1, - enum usb_port_connect_type type) -{ - struct usb_hub *hub = usb_hub_to_struct_hub(hdev); - - if (hub) - hub->ports[port1 - 1]->connect_type = type; -} - -/** - * usb_get_hub_port_connect_type - Get the port's connect type - * @hdev: USB device belonging to the usb hub - * @port1: port num of the port - * - * Return: The connect type of the port if successful. Or - * USB_PORT_CONNECT_TYPE_UNKNOWN if input params are invalid. - */ -enum usb_port_connect_type -usb_get_hub_port_connect_type(struct usb_device *hdev, int port1) -{ - struct usb_hub *hub = usb_hub_to_struct_hub(hdev); - - if (!hub) - return USB_PORT_CONNECT_TYPE_UNKNOWN; - - return hub->ports[port1 - 1]->connect_type; -} - void usb_hub_adjust_deviceremovable(struct usb_device *hdev, struct usb_hub_descriptor *desc) { + struct usb_hub *hub = usb_hub_to_struct_hub(hdev); enum usb_port_connect_type connect_type; int i; + if (!hub) + return; + if (!hub_is_superspeed(hdev)) { for (i = 1; i <= hdev->maxchild; i++) { - connect_type = usb_get_hub_port_connect_type(hdev, i); + struct usb_port *port_dev = hub->ports[i - 1]; + connect_type = port_dev->connect_type; if (connect_type == USB_PORT_CONNECT_TYPE_HARD_WIRED) { u8 mask = 1 << (i%8); if (!(desc->u.hs.DeviceRemovable[i/8] & mask)) { - dev_dbg(&hdev->dev, "usb port%d's DeviceRemovable is changed to 1 according to platform information.\n", - i); + dev_dbg(&port_dev->dev, "DeviceRemovable is changed to 1 according to platform information.\n"); desc->u.hs.DeviceRemovable[i/8] |= mask; } } @@ -5427,14 +5633,14 @@ void usb_hub_adjust_deviceremovable(struct usb_device *hdev, u16 port_removable = le16_to_cpu(desc->u.ss.DeviceRemovable); for (i = 1; i <= hdev->maxchild; i++) { - connect_type = usb_get_hub_port_connect_type(hdev, i); + struct usb_port *port_dev = hub->ports[i - 1]; + connect_type = port_dev->connect_type; if (connect_type == USB_PORT_CONNECT_TYPE_HARD_WIRED) { u16 mask = 1 << i; if (!(port_removable & mask)) { - dev_dbg(&hdev->dev, "usb port%d's DeviceRemovable is changed to 1 according to platform information.\n", - i); + dev_dbg(&port_dev->dev, "DeviceRemovable is changed to 1 according to platform information.\n"); port_removable |= mask; } } @@ -5461,6 +5667,6 @@ acpi_handle usb_get_hub_port_acpi_handle(struct usb_device *hdev, if (!hub) return NULL; - return DEVICE_ACPI_HANDLE(&hub->ports[port1 - 1]->dev); + return ACPI_HANDLE(&hub->ports[port1 - 1]->dev); } #endif |