diff options
Diffstat (limited to 'drivers/tty/serial/sunsu.c')
| -rw-r--r-- | drivers/tty/serial/sunsu.c | 1600 |
1 files changed, 1600 insertions, 0 deletions
diff --git a/drivers/tty/serial/sunsu.c b/drivers/tty/serial/sunsu.c new file mode 100644 index 00000000000..5326ae195e5 --- /dev/null +++ b/drivers/tty/serial/sunsu.c @@ -0,0 +1,1600 @@ +/* + * su.c: Small serial driver for keyboard/mouse interface on sparc32/PCI + * + * Copyright (C) 1997 Eddie C. Dost (ecd@skynet.be) + * Copyright (C) 1998-1999 Pete Zaitcev (zaitcev@yahoo.com) + * + * This is mainly a variation of 8250.c, credits go to authors mentioned + * therein. In fact this driver should be merged into the generic 8250.c + * infrastructure perhaps using a 8250_sparc.c module. + * + * Fixed to use tty_get_baud_rate(). + * Theodore Ts'o <tytso@mit.edu>, 2001-Oct-12 + * + * Converted to new 2.5.x UART layer. + * David S. Miller (davem@davemloft.net), 2002-Jul-29 + */ + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/spinlock.h> +#include <linux/errno.h> +#include <linux/tty.h> +#include <linux/tty_flip.h> +#include <linux/major.h> +#include <linux/string.h> +#include <linux/ptrace.h> +#include <linux/ioport.h> +#include <linux/circ_buf.h> +#include <linux/serial.h> +#include <linux/sysrq.h> +#include <linux/console.h> +#include <linux/slab.h> +#ifdef CONFIG_SERIO +#include <linux/serio.h> +#endif +#include <linux/serial_reg.h> +#include <linux/init.h> +#include <linux/delay.h> +#include <linux/of_device.h> + +#include <asm/io.h> +#include <asm/irq.h> +#include <asm/prom.h> +#include <asm/setup.h> + +#if defined(CONFIG_SERIAL_SUNSU_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) +#define SUPPORT_SYSRQ +#endif + +#include <linux/serial_core.h> +#include <linux/sunserialcore.h> + +/* We are on a NS PC87303 clocked with 24.0 MHz, which results + * in a UART clock of 1.8462 MHz. + */ +#define SU_BASE_BAUD (1846200 / 16) + +enum su_type { SU_PORT_NONE, SU_PORT_MS, SU_PORT_KBD, SU_PORT_PORT }; +static char *su_typev[] = { "su(???)", "su(mouse)", "su(kbd)", "su(serial)" }; + +struct serial_uart_config { + char *name; + int dfl_xmit_fifo_size; + int flags; +}; + +/* + * Here we define the default xmit fifo size used for each type of UART. + */ +static const struct serial_uart_config uart_config[] = { + { "unknown", 1, 0 }, + { "8250", 1, 0 }, + { "16450", 1, 0 }, + { "16550", 1, 0 }, + { "16550A", 16, UART_CLEAR_FIFO | UART_USE_FIFO }, + { "Cirrus", 1, 0 }, + { "ST16650", 1, UART_CLEAR_FIFO | UART_STARTECH }, + { "ST16650V2", 32, UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH }, + { "TI16750", 64, UART_CLEAR_FIFO | UART_USE_FIFO }, + { "Startech", 1, 0 }, + { "16C950/954", 128, UART_CLEAR_FIFO | UART_USE_FIFO }, + { "ST16654", 64, UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH }, + { "XR16850", 128, UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH }, + { "RSA", 2048, UART_CLEAR_FIFO | UART_USE_FIFO } +}; + +struct uart_sunsu_port { + struct uart_port port; + unsigned char acr; + unsigned char ier; + unsigned short rev; + unsigned char lcr; + unsigned int lsr_break_flag; + unsigned int cflag; + + /* Probing information. */ + enum su_type su_type; + unsigned int type_probed; /* XXX Stupid */ + unsigned long reg_size; + +#ifdef CONFIG_SERIO + struct serio serio; + int serio_open; +#endif +}; + +static unsigned int serial_in(struct uart_sunsu_port *up, int offset) +{ + offset <<= up->port.regshift; + + switch (up->port.iotype) { + case UPIO_HUB6: + outb(up->port.hub6 - 1 + offset, up->port.iobase); + return inb(up->port.iobase + 1); + + case UPIO_MEM: + return readb(up->port.membase + offset); + + default: + return inb(up->port.iobase + offset); + } +} + +static void serial_out(struct uart_sunsu_port *up, int offset, int value) +{ +#ifndef CONFIG_SPARC64 + /* + * MrCoffee has weird schematics: IRQ4 & P10(?) pins of SuperIO are + * connected with a gate then go to SlavIO. When IRQ4 goes tristated + * gate outputs a logical one. Since we use level triggered interrupts + * we have lockup and watchdog reset. We cannot mask IRQ because + * keyboard shares IRQ with us (Word has it as Bob Smelik's design). + * This problem is similar to what Alpha people suffer, see serial.c. + */ + if (offset == UART_MCR) + value |= UART_MCR_OUT2; +#endif + offset <<= up->port.regshift; + + switch (up->port.iotype) { + case UPIO_HUB6: + outb(up->port.hub6 - 1 + offset, up->port.iobase); + outb(value, up->port.iobase + 1); + break; + + case UPIO_MEM: + writeb(value, up->port.membase + offset); + break; + + default: + outb(value, up->port.iobase + offset); + } +} + +/* + * We used to support using pause I/O for certain machines. We + * haven't supported this for a while, but just in case it's badly + * needed for certain old 386 machines, I've left these #define's + * in.... + */ +#define serial_inp(up, offset) serial_in(up, offset) +#define serial_outp(up, offset, value) serial_out(up, offset, value) + + +/* + * For the 16C950 + */ +static void serial_icr_write(struct uart_sunsu_port *up, int offset, int value) +{ + serial_out(up, UART_SCR, offset); + serial_out(up, UART_ICR, value); +} + +#if 0 /* Unused currently */ +static unsigned int serial_icr_read(struct uart_sunsu_port *up, int offset) +{ + unsigned int value; + + serial_icr_write(up, UART_ACR, up->acr | UART_ACR_ICRRD); + serial_out(up, UART_SCR, offset); + value = serial_in(up, UART_ICR); + serial_icr_write(up, UART_ACR, up->acr); + + return value; +} +#endif + +#ifdef CONFIG_SERIAL_8250_RSA +/* + * Attempts to turn on the RSA FIFO. Returns zero on failure. + * We set the port uart clock rate if we succeed. + */ +static int __enable_rsa(struct uart_sunsu_port *up) +{ + unsigned char mode; + int result; + + mode = serial_inp(up, UART_RSA_MSR); + result = mode & UART_RSA_MSR_FIFO; + + if (!result) { + serial_outp(up, UART_RSA_MSR, mode | UART_RSA_MSR_FIFO); + mode = serial_inp(up, UART_RSA_MSR); + result = mode & UART_RSA_MSR_FIFO; + } + + if (result) + up->port.uartclk = SERIAL_RSA_BAUD_BASE * 16; + + return result; +} + +static void enable_rsa(struct uart_sunsu_port *up) +{ + if (up->port.type == PORT_RSA) { + if (up->port.uartclk != SERIAL_RSA_BAUD_BASE * 16) { + spin_lock_irq(&up->port.lock); + __enable_rsa(up); + spin_unlock_irq(&up->port.lock); + } + if (up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16) + serial_outp(up, UART_RSA_FRR, 0); + } +} + +/* + * Attempts to turn off the RSA FIFO. Returns zero on failure. + * It is unknown why interrupts were disabled in here. However, + * the caller is expected to preserve this behaviour by grabbing + * the spinlock before calling this function. + */ +static void disable_rsa(struct uart_sunsu_port *up) +{ + unsigned char mode; + int result; + + if (up->port.type == PORT_RSA && + up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16) { + spin_lock_irq(&up->port.lock); + + mode = serial_inp(up, UART_RSA_MSR); + result = !(mode & UART_RSA_MSR_FIFO); + + if (!result) { + serial_outp(up, UART_RSA_MSR, mode & ~UART_RSA_MSR_FIFO); + mode = serial_inp(up, UART_RSA_MSR); + result = !(mode & UART_RSA_MSR_FIFO); + } + + if (result) + up->port.uartclk = SERIAL_RSA_BAUD_BASE_LO * 16; + spin_unlock_irq(&up->port.lock); + } +} +#endif /* CONFIG_SERIAL_8250_RSA */ + +static inline void __stop_tx(struct uart_sunsu_port *p) +{ + if (p->ier & UART_IER_THRI) { + p->ier &= ~UART_IER_THRI; + serial_out(p, UART_IER, p->ier); + } +} + +static void sunsu_stop_tx(struct uart_port *port) +{ + struct uart_sunsu_port *up = (struct uart_sunsu_port *) port; + + __stop_tx(up); + + /* + * We really want to stop the transmitter from sending. + */ + if (up->port.type == PORT_16C950) { + up->acr |= UART_ACR_TXDIS; + serial_icr_write(up, UART_ACR, up->acr); + } +} + +static void sunsu_start_tx(struct uart_port *port) +{ + struct uart_sunsu_port *up = (struct uart_sunsu_port *) port; + + if (!(up->ier & UART_IER_THRI)) { + up->ier |= UART_IER_THRI; + serial_out(up, UART_IER, up->ier); + } + + /* + * Re-enable the transmitter if we disabled it. + */ + if (up->port.type == PORT_16C950 && up->acr & UART_ACR_TXDIS) { + up->acr &= ~UART_ACR_TXDIS; + serial_icr_write(up, UART_ACR, up->acr); + } +} + +static void sunsu_stop_rx(struct uart_port *port) +{ + struct uart_sunsu_port *up = (struct uart_sunsu_port *) port; + + up->ier &= ~UART_IER_RLSI; + up->port.read_status_mask &= ~UART_LSR_DR; + serial_out(up, UART_IER, up->ier); +} + +static void sunsu_enable_ms(struct uart_port *port) +{ + struct uart_sunsu_port *up = (struct uart_sunsu_port *) port; + unsigned long flags; + + spin_lock_irqsave(&up->port.lock, flags); + up->ier |= UART_IER_MSI; + serial_out(up, UART_IER, up->ier); + spin_unlock_irqrestore(&up->port.lock, flags); +} + +static void +receive_chars(struct uart_sunsu_port *up, unsigned char *status) +{ + struct tty_port *port = &up->port.state->port; + unsigned char ch, flag; + int max_count = 256; + int saw_console_brk = 0; + + do { + ch = serial_inp(up, UART_RX); + flag = TTY_NORMAL; + up->port.icount.rx++; + + if (unlikely(*status & (UART_LSR_BI | UART_LSR_PE | + UART_LSR_FE | UART_LSR_OE))) { + /* + * For statistics only + */ + if (*status & UART_LSR_BI) { + *status &= ~(UART_LSR_FE | UART_LSR_PE); + up->port.icount.brk++; + if (up->port.cons != NULL && + up->port.line == up->port.cons->index) + saw_console_brk = 1; + /* + * We do the SysRQ and SAK checking + * here because otherwise the break + * may get masked by ignore_status_mask + * or read_status_mask. + */ + if (uart_handle_break(&up->port)) + goto ignore_char; + } else if (*status & UART_LSR_PE) + up->port.icount.parity++; + else if (*status & UART_LSR_FE) + up->port.icount.frame++; + if (*status & UART_LSR_OE) + up->port.icount.overrun++; + + /* + * Mask off conditions which should be ingored. + */ + *status &= up->port.read_status_mask; + + if (up->port.cons != NULL && + up->port.line == up->port.cons->index) { + /* Recover the break flag from console xmit */ + *status |= up->lsr_break_flag; + up->lsr_break_flag = 0; + } + + if (*status & UART_LSR_BI) { + flag = TTY_BREAK; + } else if (*status & UART_LSR_PE) + flag = TTY_PARITY; + else if (*status & UART_LSR_FE) + flag = TTY_FRAME; + } + if (uart_handle_sysrq_char(&up->port, ch)) + goto ignore_char; + if ((*status & up->port.ignore_status_mask) == 0) + tty_insert_flip_char(port, ch, flag); + if (*status & UART_LSR_OE) + /* + * Overrun is special, since it's reported + * immediately, and doesn't affect the current + * character. + */ + tty_insert_flip_char(port, 0, TTY_OVERRUN); + ignore_char: + *status = serial_inp(up, UART_LSR); + } while ((*status & UART_LSR_DR) && (max_count-- > 0)); + + if (saw_console_brk) + sun_do_break(); +} + +static void transmit_chars(struct uart_sunsu_port *up) +{ + struct circ_buf *xmit = &up->port.state->xmit; + int count; + + if (up->port.x_char) { + serial_outp(up, UART_TX, up->port.x_char); + up->port.icount.tx++; + up->port.x_char = 0; + return; + } + if (uart_tx_stopped(&up->port)) { + sunsu_stop_tx(&up->port); + return; + } + if (uart_circ_empty(xmit)) { + __stop_tx(up); + return; + } + + count = up->port.fifosize; + do { + serial_out(up, UART_TX, xmit->buf[xmit->tail]); + xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); + up->port.icount.tx++; + if (uart_circ_empty(xmit)) + break; + } while (--count > 0); + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(&up->port); + + if (uart_circ_empty(xmit)) + __stop_tx(up); +} + +static void check_modem_status(struct uart_sunsu_port *up) +{ + int status; + + status = serial_in(up, UART_MSR); + + if ((status & UART_MSR_ANY_DELTA) == 0) + return; + + if (status & UART_MSR_TERI) + up->port.icount.rng++; + if (status & UART_MSR_DDSR) + up->port.icount.dsr++; + if (status & UART_MSR_DDCD) + uart_handle_dcd_change(&up->port, status & UART_MSR_DCD); + if (status & UART_MSR_DCTS) + uart_handle_cts_change(&up->port, status & UART_MSR_CTS); + + wake_up_interruptible(&up->port.state->port.delta_msr_wait); +} + +static irqreturn_t sunsu_serial_interrupt(int irq, void *dev_id) +{ + struct uart_sunsu_port *up = dev_id; + unsigned long flags; + unsigned char status; + + spin_lock_irqsave(&up->port.lock, flags); + + do { + status = serial_inp(up, UART_LSR); + if (status & UART_LSR_DR) + receive_chars(up, &status); + check_modem_status(up); + if (status & UART_LSR_THRE) + transmit_chars(up); + + spin_unlock_irqrestore(&up->port.lock, flags); + + tty_flip_buffer_push(&up->port.state->port); + + spin_lock_irqsave(&up->port.lock, flags); + + } while (!(serial_in(up, UART_IIR) & UART_IIR_NO_INT)); + + spin_unlock_irqrestore(&up->port.lock, flags); + + return IRQ_HANDLED; +} + +/* Separate interrupt handling path for keyboard/mouse ports. */ + +static void +sunsu_change_speed(struct uart_port *port, unsigned int cflag, + unsigned int iflag, unsigned int quot); + +static void sunsu_change_mouse_baud(struct uart_sunsu_port *up) +{ + unsigned int cur_cflag = up->cflag; + int quot, new_baud; + + up->cflag &= ~CBAUD; + up->cflag |= suncore_mouse_baud_cflag_next(cur_cflag, &new_baud); + + quot = up->port.uartclk / (16 * new_baud); + + sunsu_change_speed(&up->port, up->cflag, 0, quot); +} + +static void receive_kbd_ms_chars(struct uart_sunsu_port *up, int is_break) +{ + do { + unsigned char ch = serial_inp(up, UART_RX); + + /* Stop-A is handled by drivers/char/keyboard.c now. */ + if (up->su_type == SU_PORT_KBD) { +#ifdef CONFIG_SERIO + serio_interrupt(&up->serio, ch, 0); +#endif + } else if (up->su_type == SU_PORT_MS) { + int ret = suncore_mouse_baud_detection(ch, is_break); + + switch (ret) { + case 2: + sunsu_change_mouse_baud(up); + /* fallthru */ + case 1: + break; + + case 0: +#ifdef CONFIG_SERIO + serio_interrupt(&up->serio, ch, 0); +#endif + break; + } + } + } while (serial_in(up, UART_LSR) & UART_LSR_DR); +} + +static irqreturn_t sunsu_kbd_ms_interrupt(int irq, void *dev_id) +{ + struct uart_sunsu_port *up = dev_id; + + if (!(serial_in(up, UART_IIR) & UART_IIR_NO_INT)) { + unsigned char status = serial_inp(up, UART_LSR); + + if ((status & UART_LSR_DR) || (status & UART_LSR_BI)) + receive_kbd_ms_chars(up, (status & UART_LSR_BI) != 0); + } + + return IRQ_HANDLED; +} + +static unsigned int sunsu_tx_empty(struct uart_port *port) +{ + struct uart_sunsu_port *up = (struct uart_sunsu_port *) port; + unsigned long flags; + unsigned int ret; + + spin_lock_irqsave(&up->port.lock, flags); + ret = serial_in(up, UART_LSR) & UART_LSR_TEMT ? TIOCSER_TEMT : 0; + spin_unlock_irqrestore(&up->port.lock, flags); + + return ret; +} + +static unsigned int sunsu_get_mctrl(struct uart_port *port) +{ + struct uart_sunsu_port *up = (struct uart_sunsu_port *) port; + unsigned char status; + unsigned int ret; + + status = serial_in(up, UART_MSR); + + ret = 0; + if (status & UART_MSR_DCD) + ret |= TIOCM_CAR; + if (status & UART_MSR_RI) + ret |= TIOCM_RNG; + if (status & UART_MSR_DSR) + ret |= TIOCM_DSR; + if (status & UART_MSR_CTS) + ret |= TIOCM_CTS; + return ret; +} + +static void sunsu_set_mctrl(struct uart_port *port, unsigned int mctrl) +{ + struct uart_sunsu_port *up = (struct uart_sunsu_port *) port; + unsigned char mcr = 0; + + if (mctrl & TIOCM_RTS) + mcr |= UART_MCR_RTS; + if (mctrl & TIOCM_DTR) + mcr |= UART_MCR_DTR; + if (mctrl & TIOCM_OUT1) + mcr |= UART_MCR_OUT1; + if (mctrl & TIOCM_OUT2) + mcr |= UART_MCR_OUT2; + if (mctrl & TIOCM_LOOP) + mcr |= UART_MCR_LOOP; + + serial_out(up, UART_MCR, mcr); +} + +static void sunsu_break_ctl(struct uart_port *port, int break_state) +{ + struct uart_sunsu_port *up = (struct uart_sunsu_port *) port; + unsigned long flags; + + spin_lock_irqsave(&up->port.lock, flags); + if (break_state == -1) + up->lcr |= UART_LCR_SBC; + else + up->lcr &= ~UART_LCR_SBC; + serial_out(up, UART_LCR, up->lcr); + spin_unlock_irqrestore(&up->port.lock, flags); +} + +static int sunsu_startup(struct uart_port *port) +{ + struct uart_sunsu_port *up = (struct uart_sunsu_port *) port; + unsigned long flags; + int retval; + + if (up->port.type == PORT_16C950) { + /* Wake up and initialize UART */ + up->acr = 0; + serial_outp(up, UART_LCR, 0xBF); + serial_outp(up, UART_EFR, UART_EFR_ECB); + serial_outp(up, UART_IER, 0); + serial_outp(up, UART_LCR, 0); + serial_icr_write(up, UART_CSR, 0); /* Reset the UART */ + serial_outp(up, UART_LCR, 0xBF); + serial_outp(up, UART_EFR, UART_EFR_ECB); + serial_outp(up, UART_LCR, 0); + } + +#ifdef CONFIG_SERIAL_8250_RSA + /* + * If this is an RSA port, see if we can kick it up to the + * higher speed clock. + */ + enable_rsa(up); +#endif + + /* + * Clear the FIFO buffers and disable them. + * (they will be reenabled in set_termios()) + */ + if (uart_config[up->port.type].flags & UART_CLEAR_FIFO) { + serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO); + serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO | + UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT); + serial_outp(up, UART_FCR, 0); + } + + /* + * Clear the interrupt registers. + */ + (void) serial_inp(up, UART_LSR); + (void) serial_inp(up, UART_RX); + (void) serial_inp(up, UART_IIR); + (void) serial_inp(up, UART_MSR); + + /* + * At this point, there's no way the LSR could still be 0xff; + * if it is, then bail out, because there's likely no UART + * here. + */ + if (!(up->port.flags & UPF_BUGGY_UART) && + (serial_inp(up, UART_LSR) == 0xff)) { + printk("ttyS%d: LSR safety check engaged!\n", up->port.line); + return -ENODEV; + } + + if (up->su_type != SU_PORT_PORT) { + retval = request_irq(up->port.irq, sunsu_kbd_ms_interrupt, + IRQF_SHARED, su_typev[up->su_type], up); + } else { + retval = request_irq(up->port.irq, sunsu_serial_interrupt, + IRQF_SHARED, su_typev[up->su_type], up); + } + if (retval) { + printk("su: Cannot register IRQ %d\n", up->port.irq); + return retval; + } + + /* + * Now, initialize the UART + */ + serial_outp(up, UART_LCR, UART_LCR_WLEN8); + + spin_lock_irqsave(&up->port.lock, flags); + + up->port.mctrl |= TIOCM_OUT2; + + sunsu_set_mctrl(&up->port, up->port.mctrl); + spin_unlock_irqrestore(&up->port.lock, flags); + + /* + * Finally, enable interrupts. Note: Modem status interrupts + * are set via set_termios(), which will be occurring imminently + * anyway, so we don't enable them here. + */ + up->ier = UART_IER_RLSI | UART_IER_RDI; + serial_outp(up, UART_IER, up->ier); + + if (up->port.flags & UPF_FOURPORT) { + unsigned int icp; + /* + * Enable interrupts on the AST Fourport board + */ + icp = (up->port.iobase & 0xfe0) | 0x01f; + outb_p(0x80, icp); + (void) inb_p(icp); + } + + /* + * And clear the interrupt registers again for luck. + */ + (void) serial_inp(up, UART_LSR); + (void) serial_inp(up, UART_RX); + (void) serial_inp(up, UART_IIR); + (void) serial_inp(up, UART_MSR); + + return 0; +} + +static void sunsu_shutdown(struct uart_port *port) +{ + struct uart_sunsu_port *up = (struct uart_sunsu_port *) port; + unsigned long flags; + + /* + * Disable interrupts from this port + */ + up->ier = 0; + serial_outp(up, UART_IER, 0); + + spin_lock_irqsave(&up->port.lock, flags); + if (up->port.flags & UPF_FOURPORT) { + /* reset interrupts on the AST Fourport board */ + inb((up->port.iobase & 0xfe0) | 0x1f); + up->port.mctrl |= TIOCM_OUT1; + } else + up->port.mctrl &= ~TIOCM_OUT2; + + sunsu_set_mctrl(&up->port, up->port.mctrl); + spin_unlock_irqrestore(&up->port.lock, flags); + + /* + * Disable break condition and FIFOs + */ + serial_out(up, UART_LCR, serial_inp(up, UART_LCR) & ~UART_LCR_SBC); + serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO | + UART_FCR_CLEAR_RCVR | + UART_FCR_CLEAR_XMIT); + serial_outp(up, UART_FCR, 0); + +#ifdef CONFIG_SERIAL_8250_RSA + /* + * Reset the RSA board back to 115kbps compat mode. + */ + disable_rsa(up); +#endif + + /* + * Read data port to reset things. + */ + (void) serial_in(up, UART_RX); + + free_irq(up->port.irq, up); +} + +static void +sunsu_change_speed(struct uart_port *port, unsigned int cflag, + unsigned int iflag, unsigned int quot) +{ + struct uart_sunsu_port *up = (struct uart_sunsu_port *) port; + unsigned char cval, fcr = 0; + unsigned long flags; + + switch (cflag & CSIZE) { + case CS5: + cval = 0x00; + break; + case CS6: + cval = 0x01; + break; + case CS7: + cval = 0x02; + break; + default: + case CS8: + cval = 0x03; + break; + } + + if (cflag & CSTOPB) + cval |= 0x04; + if (cflag & PARENB) + cval |= UART_LCR_PARITY; + if (!(cflag & PARODD)) + cval |= UART_LCR_EPAR; +#ifdef CMSPAR + if (cflag & CMSPAR) + cval |= UART_LCR_SPAR; +#endif + + /* + * Work around a bug in the Oxford Semiconductor 952 rev B + * chip which causes it to seriously miscalculate baud rates + * when DLL is 0. + */ + if ((quot & 0xff) == 0 && up->port.type == PORT_16C950 && + up->rev == 0x5201) + quot ++; + + if (uart_config[up->port.type].flags & UART_USE_FIFO) { + if ((up->port.uartclk / quot) < (2400 * 16)) + fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_1; +#ifdef CONFIG_SERIAL_8250_RSA + else if (up->port.type == PORT_RSA) + fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_14; +#endif + else + fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_8; + } + if (up->port.type == PORT_16750) + fcr |= UART_FCR7_64BYTE; + + /* + * Ok, we're now changing the port state. Do it with + * interrupts disabled. + */ + spin_lock_irqsave(&up->port.lock, flags); + + /* + * Update the per-port timeout. + */ + uart_update_timeout(port, cflag, (port->uartclk / (16 * quot))); + + up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR; + if (iflag & INPCK) + up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE; + if (iflag & (IGNBRK | BRKINT | PARMRK)) + up->port.read_status_mask |= UART_LSR_BI; + + /* + * Characteres to ignore + */ + up->port.ignore_status_mask = 0; + if (iflag & IGNPAR) + up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE; + if (iflag & IGNBRK) { + up->port.ignore_status_mask |= UART_LSR_BI; + /* + * If we're ignoring parity and break indicators, + * ignore overruns too (for real raw support). + */ + if (iflag & IGNPAR) + up->port.ignore_status_mask |= UART_LSR_OE; + } + + /* + * ignore all characters if CREAD is not set + */ + if ((cflag & CREAD) == 0) + up->port.ignore_status_mask |= UART_LSR_DR; + + /* + * CTS flow control flag and modem status interrupts + */ + up->ier &= ~UART_IER_MSI; + if (UART_ENABLE_MS(&up->port, cflag)) + up->ier |= UART_IER_MSI; + + serial_out(up, UART_IER, up->ier); + + if (uart_config[up->port.type].flags & UART_STARTECH) { + serial_outp(up, UART_LCR, 0xBF); + serial_outp(up, UART_EFR, cflag & CRTSCTS ? UART_EFR_CTS :0); + } + serial_outp(up, UART_LCR, cval | UART_LCR_DLAB);/* set DLAB */ + serial_outp(up, UART_DLL, quot & 0xff); /* LS of divisor */ + serial_outp(up, UART_DLM, quot >> 8); /* MS of divisor */ + if (up->port.type == PORT_16750) + serial_outp(up, UART_FCR, fcr); /* set fcr */ + serial_outp(up, UART_LCR, cval); /* reset DLAB */ + up->lcr = cval; /* Save LCR */ + if (up->port.type != PORT_16750) { + if (fcr & UART_FCR_ENABLE_FIFO) { + /* emulated UARTs (Lucent Venus 167x) need two steps */ + serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO); + } + serial_outp(up, UART_FCR, fcr); /* set fcr */ + } + + up->cflag = cflag; + + spin_unlock_irqrestore(&up->port.lock, flags); +} + +static void +sunsu_set_termios(struct uart_port *port, struct ktermios *termios, + struct ktermios *old) +{ + unsigned int baud, quot; + + /* + * Ask the core to calculate the divisor for us. + */ + baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16); + quot = uart_get_divisor(port, baud); + + sunsu_change_speed(port, termios->c_cflag, termios->c_iflag, quot); +} + +static void sunsu_release_port(struct uart_port *port) +{ +} + +static int sunsu_request_port(struct uart_port *port) +{ + return 0; +} + +static void sunsu_config_port(struct uart_port *port, int flags) +{ + struct uart_sunsu_port *up = (struct uart_sunsu_port *) port; + + if (flags & UART_CONFIG_TYPE) { + /* + * We are supposed to call autoconfig here, but this requires + * splitting all the OBP probing crap from the UART probing. + * We'll do it when we kill sunsu.c altogether. + */ + port->type = up->type_probed; /* XXX */ + } +} + +static int +sunsu_verify_port(struct uart_port *port, struct serial_struct *ser) +{ + return -EINVAL; +} + +static const char * +sunsu_type(struct uart_port *port) +{ + int type = port->type; + + if (type >= ARRAY_SIZE(uart_config)) + type = 0; + return uart_config[type].name; +} + +static struct uart_ops sunsu_pops = { + .tx_empty = sunsu_tx_empty, + .set_mctrl = sunsu_set_mctrl, + .get_mctrl = sunsu_get_mctrl, + .stop_tx = sunsu_stop_tx, + .start_tx = sunsu_start_tx, + .stop_rx = sunsu_stop_rx, + .enable_ms = sunsu_enable_ms, + .break_ctl = sunsu_break_ctl, + .startup = sunsu_startup, + .shutdown = sunsu_shutdown, + .set_termios = sunsu_set_termios, + .type = sunsu_type, + .release_port = sunsu_release_port, + .request_port = sunsu_request_port, + .config_port = sunsu_config_port, + .verify_port = sunsu_verify_port, +}; + +#define UART_NR 4 + +static struct uart_sunsu_port sunsu_ports[UART_NR]; +static int nr_inst; /* Number of already registered ports */ + +#ifdef CONFIG_SERIO + +static DEFINE_SPINLOCK(sunsu_serio_lock); + +static int sunsu_serio_write(struct serio *serio, unsigned char ch) +{ + struct uart_sunsu_port *up = serio->port_data; + unsigned long flags; + int lsr; + + spin_lock_irqsave(&sunsu_serio_lock, flags); + + do { + lsr = serial_in(up, UART_LSR); + } while (!(lsr & UART_LSR_THRE)); + + /* Send the character out. */ + serial_out(up, UART_TX, ch); + + spin_unlock_irqrestore(&sunsu_serio_lock, flags); + + return 0; +} + +static int sunsu_serio_open(struct serio *serio) +{ + struct uart_sunsu_port *up = serio->port_data; + unsigned long flags; + int ret; + + spin_lock_irqsave(&sunsu_serio_lock, flags); + if (!up->serio_open) { + up->serio_open = 1; + ret = 0; + } else + ret = -EBUSY; + spin_unlock_irqrestore(&sunsu_serio_lock, flags); + + return ret; +} + +static void sunsu_serio_close(struct serio *serio) +{ + struct uart_sunsu_port *up = serio->port_data; + unsigned long flags; + + spin_lock_irqsave(&sunsu_serio_lock, flags); + up->serio_open = 0; + spin_unlock_irqrestore(&sunsu_serio_lock, flags); +} + +#endif /* CONFIG_SERIO */ + +static void sunsu_autoconfig(struct uart_sunsu_port *up) +{ + unsigned char status1, status2, scratch, scratch2, scratch3; + unsigned char save_lcr, save_mcr; + unsigned long flags; + + if (up->su_type == SU_PORT_NONE) + return; + + up->type_probed = PORT_UNKNOWN; + up->port.iotype = UPIO_MEM; + + spin_lock_irqsave(&up->port.lock, flags); + + if (!(up->port.flags & UPF_BUGGY_UART)) { + /* + * Do a simple existence test first; if we fail this, there's + * no point trying anything else. + * + * 0x80 is used as a nonsense port to prevent against false + * positives due to ISA bus float. The assumption is that + * 0x80 is a non-existent port; which should be safe since + * include/asm/io.h also makes this assumption. + */ + scratch = serial_inp(up, UART_IER); + serial_outp(up, UART_IER, 0); +#ifdef __i386__ + outb(0xff, 0x080); +#endif + scratch2 = serial_inp(up, UART_IER); + serial_outp(up, UART_IER, 0x0f); +#ifdef __i386__ + outb(0, 0x080); +#endif + scratch3 = serial_inp(up, UART_IER); + serial_outp(up, UART_IER, scratch); + if (scratch2 != 0 || scratch3 != 0x0F) + goto out; /* We failed; there's nothing here */ + } + + save_mcr = serial_in(up, UART_MCR); + save_lcr = serial_in(up, UART_LCR); + + /* + * Check to see if a UART is really there. Certain broken + * internal modems based on the Rockwell chipset fail this + * test, because they apparently don't implement the loopback + * test mode. So this test is skipped on the COM 1 through + * COM 4 ports. This *should* be safe, since no board + * manufacturer would be stupid enough to design a board + * that conflicts with COM 1-4 --- we hope! + */ + if (!(up->port.flags & UPF_SKIP_TEST)) { + serial_outp(up, UART_MCR, UART_MCR_LOOP | 0x0A); + status1 = serial_inp(up, UART_MSR) & 0xF0; + serial_outp(up, UART_MCR, save_mcr); + if (status1 != 0x90) + goto out; /* We failed loopback test */ + } + serial_outp(up, UART_LCR, 0xBF); /* set up for StarTech test */ + serial_outp(up, UART_EFR, 0); /* EFR is the same as FCR */ + serial_outp(up, UART_LCR, 0); + serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO); + scratch = serial_in(up, UART_IIR) >> 6; + switch (scratch) { + case 0: + up->port.type = PORT_16450; + break; + case 1: + up->port.type = PORT_UNKNOWN; + break; + case 2: + up->port.type = PORT_16550; + break; + case 3: + up->port.type = PORT_16550A; + break; + } + if (up->port.type == PORT_16550A) { + /* Check for Startech UART's */ + serial_outp(up, UART_LCR, UART_LCR_DLAB); + if (serial_in(up, UART_EFR) == 0) { + up->port.type = PORT_16650; + } else { + serial_outp(up, UART_LCR, 0xBF); + if (serial_in(up, UART_EFR) == 0) + up->port.type = PORT_16650V2; + } + } + if (up->port.type == PORT_16550A) { + /* Check for TI 16750 */ + serial_outp(up, UART_LCR, save_lcr | UART_LCR_DLAB); + serial_outp(up, UART_FCR, + UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE); + scratch = serial_in(up, UART_IIR) >> 5; + if (scratch == 7) { + /* + * If this is a 16750, and not a cheap UART + * clone, then it should only go into 64 byte + * mode if the UART_FCR7_64BYTE bit was set + * while UART_LCR_DLAB was latched. + */ + serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO); + serial_outp(up, UART_LCR, 0); + serial_outp(up, UART_FCR, + UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE); + scratch = serial_in(up, UART_IIR) >> 5; + if (scratch == 6) + up->port.type = PORT_16750; + } + serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO); + } + serial_outp(up, UART_LCR, save_lcr); + if (up->port.type == PORT_16450) { + scratch = serial_in(up, UART_SCR); + serial_outp(up, UART_SCR, 0xa5); + status1 = serial_in(up, UART_SCR); + serial_outp(up, UART_SCR, 0x5a); + status2 = serial_in(up, UART_SCR); + serial_outp(up, UART_SCR, scratch); + + if ((status1 != 0xa5) || (status2 != 0x5a)) + up->port.type = PORT_8250; + } + + up->port.fifosize = uart_config[up->port.type].dfl_xmit_fifo_size; + + if (up->port.type == PORT_UNKNOWN) + goto out; + up->type_probed = up->port.type; /* XXX */ + + /* + * Reset the UART. + */ +#ifdef CONFIG_SERIAL_8250_RSA + if (up->port.type == PORT_RSA) + serial_outp(up, UART_RSA_FRR, 0); +#endif + serial_outp(up, UART_MCR, save_mcr); + serial_outp(up, UART_FCR, (UART_FCR_ENABLE_FIFO | + UART_FCR_CLEAR_RCVR | + UART_FCR_CLEAR_XMIT)); + serial_outp(up, UART_FCR, 0); + (void)serial_in(up, UART_RX); + serial_outp(up, UART_IER, 0); + +out: + spin_unlock_irqrestore(&up->port.lock, flags); +} + +static struct uart_driver sunsu_reg = { + .owner = THIS_MODULE, + .driver_name = "sunsu", + .dev_name = "ttyS", + .major = TTY_MAJOR, +}; + +static int sunsu_kbd_ms_init(struct uart_sunsu_port *up) +{ + int quot, baud; +#ifdef CONFIG_SERIO + struct serio *serio; +#endif + + if (up->su_type == SU_PORT_KBD) { + up->cflag = B1200 | CS8 | CLOCAL | CREAD; + baud = 1200; + } else { + up->cflag = B4800 | CS8 | CLOCAL | CREAD; + baud = 4800; + } + quot = up->port.uartclk / (16 * baud); + + sunsu_autoconfig(up); + if (up->port.type == PORT_UNKNOWN) + return -ENODEV; + + printk("%s: %s port at %llx, irq %u\n", + up->port.dev->of_node->full_name, + (up->su_type == SU_PORT_KBD) ? "Keyboard" : "Mouse", + (unsigned long long) up->port.mapbase, + up->port.irq); + +#ifdef CONFIG_SERIO + serio = &up->serio; + serio->port_data = up; + + serio->id.type = SERIO_RS232; + if (up->su_type == SU_PORT_KBD) { + serio->id.proto = SERIO_SUNKBD; + strlcpy(serio->name, "sukbd", sizeof(serio->name)); + } else { + serio->id.proto = SERIO_SUN; + serio->id.extra = 1; + strlcpy(serio->name, "sums", sizeof(serio->name)); + } + strlcpy(serio->phys, + (!(up->port.line & 1) ? "su/serio0" : "su/serio1"), + sizeof(serio->phys)); + + serio->write = sunsu_serio_write; + serio->open = sunsu_serio_open; + serio->close = sunsu_serio_close; + serio->dev.parent = up->port.dev; + + serio_register_port(serio); +#endif + + sunsu_change_speed(&up->port, up->cflag, 0, quot); + + sunsu_startup(&up->port); + return 0; +} + +/* + * ------------------------------------------------------------ + * Serial console driver + * ------------------------------------------------------------ + */ + +#ifdef CONFIG_SERIAL_SUNSU_CONSOLE + +#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE) + +/* + * Wait for transmitter & holding register to empty + */ +static __inline__ void wait_for_xmitr(struct uart_sunsu_port *up) +{ + unsigned int status, tmout = 10000; + + /* Wait up to 10ms for the character(s) to be sent. */ + do { + status = serial_in(up, UART_LSR); + + if (status & UART_LSR_BI) + up->lsr_break_flag = UART_LSR_BI; + + if (--tmout == 0) + break; + udelay(1); + } while ((status & BOTH_EMPTY) != BOTH_EMPTY); + + /* Wait up to 1s for flow control if necessary */ + if (up->port.flags & UPF_CONS_FLOW) { + tmout = 1000000; + while (--tmout && + ((serial_in(up, UART_MSR) & UART_MSR_CTS) == 0)) + udelay(1); + } +} + +static void sunsu_console_putchar(struct uart_port *port, int ch) +{ + struct uart_sunsu_port *up = (struct uart_sunsu_port *)port; + + wait_for_xmitr(up); + serial_out(up, UART_TX, ch); +} + +/* + * Print a string to the serial port trying not to disturb + * any possible real use of the port... + */ +static void sunsu_console_write(struct console *co, const char *s, + unsigned int count) +{ + struct uart_sunsu_port *up = &sunsu_ports[co->index]; + unsigned long flags; + unsigned int ier; + int locked = 1; + + if (up->port.sysrq || oops_in_progress) + locked = spin_trylock_irqsave(&up->port.lock, flags); + else + spin_lock_irqsave(&up->port.lock, flags); + + /* + * First save the UER then disable the interrupts + */ + ier = serial_in(up, UART_IER); + serial_out(up, UART_IER, 0); + + uart_console_write(&up->port, s, count, sunsu_console_putchar); + + /* + * Finally, wait for transmitter to become empty + * and restore the IER + */ + wait_for_xmitr(up); + serial_out(up, UART_IER, ier); + + if (locked) + spin_unlock_irqrestore(&up->port.lock, flags); +} + +/* + * Setup initial baud/bits/parity. We do two things here: + * - construct a cflag setting for the first su_open() + * - initialize the serial port + * Return non-zero if we didn't find a serial port. + */ +static int __init sunsu_console_setup(struct console *co, char *options) +{ + static struct ktermios dummy; + struct ktermios termios; + struct uart_port *port; + + printk("Console: ttyS%d (SU)\n", + (sunsu_reg.minor - 64) + co->index); + + if (co->index > nr_inst) + return -ENODEV; + port = &sunsu_ports[co->index].port; + + /* + * Temporary fix. + */ + spin_lock_init(&port->lock); + + /* Get firmware console settings. */ + sunserial_console_termios(co, port->dev->of_node); + + memset(&termios, 0, sizeof(struct ktermios)); + termios.c_cflag = co->cflag; + port->mctrl |= TIOCM_DTR; + port->ops->set_termios(port, &termios, &dummy); + + return 0; +} + +static struct console sunsu_console = { + .name = "ttyS", + .write = sunsu_console_write, + .device = uart_console_device, + .setup = sunsu_console_setup, + .flags = CON_PRINTBUFFER, + .index = -1, + .data = &sunsu_reg, +}; + +/* + * Register console. + */ + +static inline struct console *SUNSU_CONSOLE(void) +{ + return &sunsu_console; +} +#else +#define SUNSU_CONSOLE() (NULL) +#define sunsu_serial_console_init() do { } while (0) +#endif + +static enum su_type su_get_type(struct device_node *dp) +{ + struct device_node *ap = of_find_node_by_path("/aliases"); + + if (ap) { + const char *keyb = of_get_property(ap, "keyboard", NULL); + const char *ms = of_get_property(ap, "mouse", NULL); + + if (keyb) { + if (dp == of_find_node_by_path(keyb)) + return SU_PORT_KBD; + } + if (ms) { + if (dp == of_find_node_by_path(ms)) + return SU_PORT_MS; + } + } + + return SU_PORT_PORT; +} + +static int su_probe(struct platform_device *op) +{ + struct device_node *dp = op->dev.of_node; + struct uart_sunsu_port *up; + struct resource *rp; + enum su_type type; + bool ignore_line; + int err; + + type = su_get_type(dp); + if (type == SU_PORT_PORT) { + if (nr_inst >= UART_NR) + return -EINVAL; + up = &sunsu_ports[nr_inst]; + } else { + up = kzalloc(sizeof(*up), GFP_KERNEL); + if (!up) + return -ENOMEM; + } + + up->port.line = nr_inst; + + spin_lock_init(&up->port.lock); + + up->su_type = type; + + rp = &op->resource[0]; + up->port.mapbase = rp->start; + up->reg_size = resource_size(rp); + up->port.membase = of_ioremap(rp, 0, up->reg_size, "su"); + if (!up->port.membase) { + if (type != SU_PORT_PORT) + kfree(up); + return -ENOMEM; + } + + up->port.irq = op->archdata.irqs[0]; + + up->port.dev = &op->dev; + + up->port.type = PORT_UNKNOWN; + up->port.uartclk = (SU_BASE_BAUD * 16); + + err = 0; + if (up->su_type == SU_PORT_KBD || up->su_type == SU_PORT_MS) { + err = sunsu_kbd_ms_init(up); + if (err) { + of_iounmap(&op->resource[0], + up->port.membase, up->reg_size); + kfree(up); + return err; + } + platform_set_drvdata(op, up); + + nr_inst++; + + return 0; + } + + up->port.flags |= UPF_BOOT_AUTOCONF; + + sunsu_autoconfig(up); + + err = -ENODEV; + if (up->port.type == PORT_UNKNOWN) + goto out_unmap; + + up->port.ops = &sunsu_pops; + + ignore_line = false; + if (!strcmp(dp->name, "rsc-console") || + !strcmp(dp->name, "lom-console")) + ignore_line = true; + + sunserial_console_match(SUNSU_CONSOLE(), dp, + &sunsu_reg, up->port.line, + ignore_line); + err = uart_add_one_port(&sunsu_reg, &up->port); + if (err) + goto out_unmap; + + platform_set_drvdata(op, up); + + nr_inst++; + + return 0; + +out_unmap: + of_iounmap(&op->resource[0], up->port.membase, up->reg_size); + return err; +} + +static int su_remove(struct platform_device *op) +{ + struct uart_sunsu_port *up = platform_get_drvdata(op); + bool kbdms = false; + + if (up->su_type == SU_PORT_MS || + up->su_type == SU_PORT_KBD) + kbdms = true; + + if (kbdms) { +#ifdef CONFIG_SERIO + serio_unregister_port(&up->serio); +#endif + } else if (up->port.type != PORT_UNKNOWN) + uart_remove_one_port(&sunsu_reg, &up->port); + + if (up->port.membase) + of_iounmap(&op->resource[0], up->port.membase, up->reg_size); + + if (kbdms) + kfree(up); + + return 0; +} + +static const struct of_device_id su_match[] = { + { + .name = "su", + }, + { + .name = "su_pnp", + }, + { + .name = "serial", + .compatible = "su", + }, + { + .type = "serial", + .compatible = "su", + }, + {}, +}; +MODULE_DEVICE_TABLE(of, su_match); + +static struct platform_driver su_driver = { + .driver = { + .name = "su", + .owner = THIS_MODULE, + .of_match_table = su_match, + }, + .probe = su_probe, + .remove = su_remove, +}; + +static int __init sunsu_init(void) +{ + struct device_node *dp; + int err; + int num_uart = 0; + + for_each_node_by_name(dp, "su") { + if (su_get_type(dp) == SU_PORT_PORT) + num_uart++; + } + for_each_node_by_name(dp, "su_pnp") { + if (su_get_type(dp) == SU_PORT_PORT) + num_uart++; + } + for_each_node_by_name(dp, "serial") { + if (of_device_is_compatible(dp, "su")) { + if (su_get_type(dp) == SU_PORT_PORT) + num_uart++; + } + } + for_each_node_by_type(dp, "serial") { + if (of_device_is_compatible(dp, "su")) { + if (su_get_type(dp) == SU_PORT_PORT) + num_uart++; + } + } + + if (num_uart) { + err = sunserial_register_minors(&sunsu_reg, num_uart); + if (err) + return err; + } + + err = platform_driver_register(&su_driver); + if (err && num_uart) + sunserial_unregister_minors(&sunsu_reg, num_uart); + + return err; +} + +static void __exit sunsu_exit(void) +{ + platform_driver_unregister(&su_driver); + if (sunsu_reg.nr) + sunserial_unregister_minors(&sunsu_reg, sunsu_reg.nr); +} + +module_init(sunsu_init); +module_exit(sunsu_exit); + +MODULE_AUTHOR("Eddie C. Dost, Peter Zaitcev, and David S. Miller"); +MODULE_DESCRIPTION("Sun SU serial port driver"); +MODULE_VERSION("2.0"); +MODULE_LICENSE("GPL"); |