diff options
Diffstat (limited to 'drivers/tty/serial/crisv10.c')
| -rw-r--r-- | drivers/tty/serial/crisv10.c | 4387 |
1 files changed, 4387 insertions, 0 deletions
diff --git a/drivers/tty/serial/crisv10.c b/drivers/tty/serial/crisv10.c new file mode 100644 index 00000000000..d567ac5d3af --- /dev/null +++ b/drivers/tty/serial/crisv10.c @@ -0,0 +1,4387 @@ +/* + * Serial port driver for the ETRAX 100LX chip + * + * Copyright (C) 1998-2007 Axis Communications AB + * + * Many, many authors. Based once upon a time on serial.c for 16x50. + * + */ + +static char *serial_version = "$Revision: 1.25 $"; + +#include <linux/types.h> +#include <linux/errno.h> +#include <linux/signal.h> +#include <linux/sched.h> +#include <linux/timer.h> +#include <linux/interrupt.h> +#include <linux/tty.h> +#include <linux/tty_flip.h> +#include <linux/major.h> +#include <linux/string.h> +#include <linux/fcntl.h> +#include <linux/mm.h> +#include <linux/slab.h> +#include <linux/init.h> +#include <linux/kernel.h> +#include <linux/mutex.h> +#include <linux/bitops.h> +#include <linux/seq_file.h> +#include <linux/delay.h> +#include <linux/module.h> +#include <linux/uaccess.h> +#include <linux/io.h> + +#include <asm/irq.h> +#include <asm/dma.h> + +#include <arch/svinto.h> +#include <arch/system.h> + +/* non-arch dependent serial structures are in linux/serial.h */ +#include <linux/serial.h> +/* while we keep our own stuff (struct e100_serial) in a local .h file */ +#include "crisv10.h" +#include <asm/fasttimer.h> +#include <arch/io_interface_mux.h> + +#ifdef CONFIG_ETRAX_SERIAL_FAST_TIMER +#ifndef CONFIG_ETRAX_FAST_TIMER +#error "Enable FAST_TIMER to use SERIAL_FAST_TIMER" +#endif +#endif + +#if defined(CONFIG_ETRAX_SERIAL_RX_TIMEOUT_TICKS) && \ + (CONFIG_ETRAX_SERIAL_RX_TIMEOUT_TICKS == 0) +#error "RX_TIMEOUT_TICKS == 0 not allowed, use 1" +#endif + +#if defined(CONFIG_ETRAX_RS485_ON_PA) && defined(CONFIG_ETRAX_RS485_ON_PORT_G) +#error "Disable either CONFIG_ETRAX_RS485_ON_PA or CONFIG_ETRAX_RS485_ON_PORT_G" +#endif + +/* + * All of the compatibilty code so we can compile serial.c against + * older kernels is hidden in serial_compat.h + */ +#if defined(LOCAL_HEADERS) +#include "serial_compat.h" +#endif + +struct tty_driver *serial_driver; + +/* number of characters left in xmit buffer before we ask for more */ +#define WAKEUP_CHARS 256 + +//#define SERIAL_DEBUG_INTR +//#define SERIAL_DEBUG_OPEN +//#define SERIAL_DEBUG_FLOW +//#define SERIAL_DEBUG_DATA +//#define SERIAL_DEBUG_THROTTLE +//#define SERIAL_DEBUG_IO /* Debug for Extra control and status pins */ +//#define SERIAL_DEBUG_LINE 0 /* What serport we want to debug */ + +/* Enable this to use serial interrupts to handle when you + expect the first received event on the serial port to + be an error, break or similar. Used to be able to flash IRMA + from eLinux */ +#define SERIAL_HANDLE_EARLY_ERRORS + +/* Currently 16 descriptors x 128 bytes = 2048 bytes */ +#define SERIAL_DESCR_BUF_SIZE 256 + +#define SERIAL_PRESCALE_BASE 3125000 /* 3.125MHz */ +#define DEF_BAUD_BASE SERIAL_PRESCALE_BASE + +/* We don't want to load the system with massive fast timer interrupt + * on high baudrates so limit it to 250 us (4kHz) */ +#define MIN_FLUSH_TIME_USEC 250 + +/* Add an x here to log a lot of timer stuff */ +#define TIMERD(x) +/* Debug details of interrupt handling */ +#define DINTR1(x) /* irq on/off, errors */ +#define DINTR2(x) /* tx and rx */ +/* Debug flip buffer stuff */ +#define DFLIP(x) +/* Debug flow control and overview of data flow */ +#define DFLOW(x) +#define DBAUD(x) +#define DLOG_INT_TRIG(x) + +//#define DEBUG_LOG_INCLUDED +#ifndef DEBUG_LOG_INCLUDED +#define DEBUG_LOG(line, string, value) +#else +struct debug_log_info +{ + unsigned long time; + unsigned long timer_data; +// int line; + const char *string; + int value; +}; +#define DEBUG_LOG_SIZE 4096 + +struct debug_log_info debug_log[DEBUG_LOG_SIZE]; +int debug_log_pos = 0; + +#define DEBUG_LOG(_line, _string, _value) do { \ + if ((_line) == SERIAL_DEBUG_LINE) {\ + debug_log_func(_line, _string, _value); \ + }\ +}while(0) + +void debug_log_func(int line, const char *string, int value) +{ + if (debug_log_pos < DEBUG_LOG_SIZE) { + debug_log[debug_log_pos].time = jiffies; + debug_log[debug_log_pos].timer_data = *R_TIMER_DATA; +// debug_log[debug_log_pos].line = line; + debug_log[debug_log_pos].string = string; + debug_log[debug_log_pos].value = value; + debug_log_pos++; + } + /*printk(string, value);*/ +} +#endif + +#ifndef CONFIG_ETRAX_SERIAL_RX_TIMEOUT_TICKS +/* Default number of timer ticks before flushing rx fifo + * When using "little data, low latency applications: use 0 + * When using "much data applications (PPP)" use ~5 + */ +#define CONFIG_ETRAX_SERIAL_RX_TIMEOUT_TICKS 5 +#endif + +unsigned long timer_data_to_ns(unsigned long timer_data); + +static void change_speed(struct e100_serial *info); +static void rs_throttle(struct tty_struct * tty); +static void rs_wait_until_sent(struct tty_struct *tty, int timeout); +static int rs_write(struct tty_struct *tty, + const unsigned char *buf, int count); +#ifdef CONFIG_ETRAX_RS485 +static int e100_write_rs485(struct tty_struct *tty, + const unsigned char *buf, int count); +#endif +static int get_lsr_info(struct e100_serial *info, unsigned int *value); + + +#define DEF_BAUD 115200 /* 115.2 kbit/s */ +#define DEF_RX 0x20 /* or SERIAL_CTRL_W >> 8 */ +/* Default value of tx_ctrl register: has txd(bit 7)=1 (idle) as default */ +#define DEF_TX 0x80 /* or SERIAL_CTRL_B */ + +/* offsets from R_SERIALx_CTRL */ + +#define REG_DATA 0 +#define REG_DATA_STATUS32 0 /* this is the 32 bit register R_SERIALx_READ */ +#define REG_TR_DATA 0 +#define REG_STATUS 1 +#define REG_TR_CTRL 1 +#define REG_REC_CTRL 2 +#define REG_BAUD 3 +#define REG_XOFF 4 /* this is a 32 bit register */ + +/* The bitfields are the same for all serial ports */ +#define SER_RXD_MASK IO_MASK(R_SERIAL0_STATUS, rxd) +#define SER_DATA_AVAIL_MASK IO_MASK(R_SERIAL0_STATUS, data_avail) +#define SER_FRAMING_ERR_MASK IO_MASK(R_SERIAL0_STATUS, framing_err) +#define SER_PAR_ERR_MASK IO_MASK(R_SERIAL0_STATUS, par_err) +#define SER_OVERRUN_MASK IO_MASK(R_SERIAL0_STATUS, overrun) + +#define SER_ERROR_MASK (SER_OVERRUN_MASK | SER_PAR_ERR_MASK | SER_FRAMING_ERR_MASK) + +/* Values for info->errorcode */ +#define ERRCODE_SET_BREAK (TTY_BREAK) +#define ERRCODE_INSERT 0x100 +#define ERRCODE_INSERT_BREAK (ERRCODE_INSERT | TTY_BREAK) + +#define FORCE_EOP(info) *R_SET_EOP = 1U << info->iseteop; + +/* + * General note regarding the use of IO_* macros in this file: + * + * We will use the bits defined for DMA channel 6 when using various + * IO_* macros (e.g. IO_STATE, IO_MASK, IO_EXTRACT) and _assume_ they are + * the same for all channels (which of course they are). + * + * We will also use the bits defined for serial port 0 when writing commands + * to the different ports, as these bits too are the same for all ports. + */ + + +/* Mask for the irqs possibly enabled in R_IRQ_MASK1_RD etc. */ +static const unsigned long e100_ser_int_mask = 0 +#ifdef CONFIG_ETRAX_SERIAL_PORT0 +| IO_MASK(R_IRQ_MASK1_RD, ser0_data) | IO_MASK(R_IRQ_MASK1_RD, ser0_ready) +#endif +#ifdef CONFIG_ETRAX_SERIAL_PORT1 +| IO_MASK(R_IRQ_MASK1_RD, ser1_data) | IO_MASK(R_IRQ_MASK1_RD, ser1_ready) +#endif +#ifdef CONFIG_ETRAX_SERIAL_PORT2 +| IO_MASK(R_IRQ_MASK1_RD, ser2_data) | IO_MASK(R_IRQ_MASK1_RD, ser2_ready) +#endif +#ifdef CONFIG_ETRAX_SERIAL_PORT3 +| IO_MASK(R_IRQ_MASK1_RD, ser3_data) | IO_MASK(R_IRQ_MASK1_RD, ser3_ready) +#endif +; +unsigned long r_alt_ser_baudrate_shadow = 0; + +/* this is the data for the four serial ports in the etrax100 */ +/* DMA2(ser2), DMA4(ser3), DMA6(ser0) or DMA8(ser1) */ +/* R_DMA_CHx_CLR_INTR, R_DMA_CHx_FIRST, R_DMA_CHx_CMD */ + +static struct e100_serial rs_table[] = { + { .baud = DEF_BAUD, + .ioport = (unsigned char *)R_SERIAL0_CTRL, + .irq = 1U << 12, /* uses DMA 6 and 7 */ + .oclrintradr = R_DMA_CH6_CLR_INTR, + .ofirstadr = R_DMA_CH6_FIRST, + .ocmdadr = R_DMA_CH6_CMD, + .ostatusadr = R_DMA_CH6_STATUS, + .iclrintradr = R_DMA_CH7_CLR_INTR, + .ifirstadr = R_DMA_CH7_FIRST, + .icmdadr = R_DMA_CH7_CMD, + .idescradr = R_DMA_CH7_DESCR, + .rx_ctrl = DEF_RX, + .tx_ctrl = DEF_TX, + .iseteop = 2, + .dma_owner = dma_ser0, + .io_if = if_serial_0, +#ifdef CONFIG_ETRAX_SERIAL_PORT0 + .enabled = 1, +#ifdef CONFIG_ETRAX_SERIAL_PORT0_DMA6_OUT + .dma_out_enabled = 1, + .dma_out_nbr = SER0_TX_DMA_NBR, + .dma_out_irq_nbr = SER0_DMA_TX_IRQ_NBR, + .dma_out_irq_flags = 0, + .dma_out_irq_description = "serial 0 dma tr", +#else + .dma_out_enabled = 0, + .dma_out_nbr = UINT_MAX, + .dma_out_irq_nbr = 0, + .dma_out_irq_flags = 0, + .dma_out_irq_description = NULL, +#endif +#ifdef CONFIG_ETRAX_SERIAL_PORT0_DMA7_IN + .dma_in_enabled = 1, + .dma_in_nbr = SER0_RX_DMA_NBR, + .dma_in_irq_nbr = SER0_DMA_RX_IRQ_NBR, + .dma_in_irq_flags = 0, + .dma_in_irq_description = "serial 0 dma rec", +#else + .dma_in_enabled = 0, + .dma_in_nbr = UINT_MAX, + .dma_in_irq_nbr = 0, + .dma_in_irq_flags = 0, + .dma_in_irq_description = NULL, +#endif +#else + .enabled = 0, + .io_if_description = NULL, + .dma_out_enabled = 0, + .dma_in_enabled = 0 +#endif + +}, /* ttyS0 */ + { .baud = DEF_BAUD, + .ioport = (unsigned char *)R_SERIAL1_CTRL, + .irq = 1U << 16, /* uses DMA 8 and 9 */ + .oclrintradr = R_DMA_CH8_CLR_INTR, + .ofirstadr = R_DMA_CH8_FIRST, + .ocmdadr = R_DMA_CH8_CMD, + .ostatusadr = R_DMA_CH8_STATUS, + .iclrintradr = R_DMA_CH9_CLR_INTR, + .ifirstadr = R_DMA_CH9_FIRST, + .icmdadr = R_DMA_CH9_CMD, + .idescradr = R_DMA_CH9_DESCR, + .rx_ctrl = DEF_RX, + .tx_ctrl = DEF_TX, + .iseteop = 3, + .dma_owner = dma_ser1, + .io_if = if_serial_1, +#ifdef CONFIG_ETRAX_SERIAL_PORT1 + .enabled = 1, + .io_if_description = "ser1", +#ifdef CONFIG_ETRAX_SERIAL_PORT1_DMA8_OUT + .dma_out_enabled = 1, + .dma_out_nbr = SER1_TX_DMA_NBR, + .dma_out_irq_nbr = SER1_DMA_TX_IRQ_NBR, + .dma_out_irq_flags = 0, + .dma_out_irq_description = "serial 1 dma tr", +#else + .dma_out_enabled = 0, + .dma_out_nbr = UINT_MAX, + .dma_out_irq_nbr = 0, + .dma_out_irq_flags = 0, + .dma_out_irq_description = NULL, +#endif +#ifdef CONFIG_ETRAX_SERIAL_PORT1_DMA9_IN + .dma_in_enabled = 1, + .dma_in_nbr = SER1_RX_DMA_NBR, + .dma_in_irq_nbr = SER1_DMA_RX_IRQ_NBR, + .dma_in_irq_flags = 0, + .dma_in_irq_description = "serial 1 dma rec", +#else + .dma_in_enabled = 0, + .dma_in_enabled = 0, + .dma_in_nbr = UINT_MAX, + .dma_in_irq_nbr = 0, + .dma_in_irq_flags = 0, + .dma_in_irq_description = NULL, +#endif +#else + .enabled = 0, + .io_if_description = NULL, + .dma_in_irq_nbr = 0, + .dma_out_enabled = 0, + .dma_in_enabled = 0 +#endif +}, /* ttyS1 */ + + { .baud = DEF_BAUD, + .ioport = (unsigned char *)R_SERIAL2_CTRL, + .irq = 1U << 4, /* uses DMA 2 and 3 */ + .oclrintradr = R_DMA_CH2_CLR_INTR, + .ofirstadr = R_DMA_CH2_FIRST, + .ocmdadr = R_DMA_CH2_CMD, + .ostatusadr = R_DMA_CH2_STATUS, + .iclrintradr = R_DMA_CH3_CLR_INTR, + .ifirstadr = R_DMA_CH3_FIRST, + .icmdadr = R_DMA_CH3_CMD, + .idescradr = R_DMA_CH3_DESCR, + .rx_ctrl = DEF_RX, + .tx_ctrl = DEF_TX, + .iseteop = 0, + .dma_owner = dma_ser2, + .io_if = if_serial_2, +#ifdef CONFIG_ETRAX_SERIAL_PORT2 + .enabled = 1, + .io_if_description = "ser2", +#ifdef CONFIG_ETRAX_SERIAL_PORT2_DMA2_OUT + .dma_out_enabled = 1, + .dma_out_nbr = SER2_TX_DMA_NBR, + .dma_out_irq_nbr = SER2_DMA_TX_IRQ_NBR, + .dma_out_irq_flags = 0, + .dma_out_irq_description = "serial 2 dma tr", +#else + .dma_out_enabled = 0, + .dma_out_nbr = UINT_MAX, + .dma_out_irq_nbr = 0, + .dma_out_irq_flags = 0, + .dma_out_irq_description = NULL, +#endif +#ifdef CONFIG_ETRAX_SERIAL_PORT2_DMA3_IN + .dma_in_enabled = 1, + .dma_in_nbr = SER2_RX_DMA_NBR, + .dma_in_irq_nbr = SER2_DMA_RX_IRQ_NBR, + .dma_in_irq_flags = 0, + .dma_in_irq_description = "serial 2 dma rec", +#else + .dma_in_enabled = 0, + .dma_in_nbr = UINT_MAX, + .dma_in_irq_nbr = 0, + .dma_in_irq_flags = 0, + .dma_in_irq_description = NULL, +#endif +#else + .enabled = 0, + .io_if_description = NULL, + .dma_out_enabled = 0, + .dma_in_enabled = 0 +#endif + }, /* ttyS2 */ + + { .baud = DEF_BAUD, + .ioport = (unsigned char *)R_SERIAL3_CTRL, + .irq = 1U << 8, /* uses DMA 4 and 5 */ + .oclrintradr = R_DMA_CH4_CLR_INTR, + .ofirstadr = R_DMA_CH4_FIRST, + .ocmdadr = R_DMA_CH4_CMD, + .ostatusadr = R_DMA_CH4_STATUS, + .iclrintradr = R_DMA_CH5_CLR_INTR, + .ifirstadr = R_DMA_CH5_FIRST, + .icmdadr = R_DMA_CH5_CMD, + .idescradr = R_DMA_CH5_DESCR, + .rx_ctrl = DEF_RX, + .tx_ctrl = DEF_TX, + .iseteop = 1, + .dma_owner = dma_ser3, + .io_if = if_serial_3, +#ifdef CONFIG_ETRAX_SERIAL_PORT3 + .enabled = 1, + .io_if_description = "ser3", +#ifdef CONFIG_ETRAX_SERIAL_PORT3_DMA4_OUT + .dma_out_enabled = 1, + .dma_out_nbr = SER3_TX_DMA_NBR, + .dma_out_irq_nbr = SER3_DMA_TX_IRQ_NBR, + .dma_out_irq_flags = 0, + .dma_out_irq_description = "serial 3 dma tr", +#else + .dma_out_enabled = 0, + .dma_out_nbr = UINT_MAX, + .dma_out_irq_nbr = 0, + .dma_out_irq_flags = 0, + .dma_out_irq_description = NULL, +#endif +#ifdef CONFIG_ETRAX_SERIAL_PORT3_DMA5_IN + .dma_in_enabled = 1, + .dma_in_nbr = SER3_RX_DMA_NBR, + .dma_in_irq_nbr = SER3_DMA_RX_IRQ_NBR, + .dma_in_irq_flags = 0, + .dma_in_irq_description = "serial 3 dma rec", +#else + .dma_in_enabled = 0, + .dma_in_nbr = UINT_MAX, + .dma_in_irq_nbr = 0, + .dma_in_irq_flags = 0, + .dma_in_irq_description = NULL +#endif +#else + .enabled = 0, + .io_if_description = NULL, + .dma_out_enabled = 0, + .dma_in_enabled = 0 +#endif + } /* ttyS3 */ +}; + + +#define NR_PORTS (sizeof(rs_table)/sizeof(struct e100_serial)) + +#ifdef CONFIG_ETRAX_SERIAL_FAST_TIMER +static struct fast_timer fast_timers[NR_PORTS]; +#endif + +#ifdef CONFIG_ETRAX_SERIAL_PROC_ENTRY +#define PROCSTAT(x) x +struct ser_statistics_type { + int overrun_cnt; + int early_errors_cnt; + int ser_ints_ok_cnt; + int errors_cnt; + unsigned long int processing_flip; + unsigned long processing_flip_still_room; + unsigned long int timeout_flush_cnt; + int rx_dma_ints; + int tx_dma_ints; + int rx_tot; + int tx_tot; +}; + +static struct ser_statistics_type ser_stat[NR_PORTS]; + +#else + +#define PROCSTAT(x) + +#endif /* CONFIG_ETRAX_SERIAL_PROC_ENTRY */ + +/* RS-485 */ +#if defined(CONFIG_ETRAX_RS485) +#ifdef CONFIG_ETRAX_FAST_TIMER +static struct fast_timer fast_timers_rs485[NR_PORTS]; +#endif +#if defined(CONFIG_ETRAX_RS485_ON_PA) +static int rs485_pa_bit = CONFIG_ETRAX_RS485_ON_PA_BIT; +#endif +#if defined(CONFIG_ETRAX_RS485_ON_PORT_G) +static int rs485_port_g_bit = CONFIG_ETRAX_RS485_ON_PORT_G_BIT; +#endif +#endif + +/* Info and macros needed for each ports extra control/status signals. */ +#define E100_STRUCT_PORT(line, pinname) \ + ((CONFIG_ETRAX_SER##line##_##pinname##_ON_PA_BIT >= 0)? \ + (R_PORT_PA_DATA): ( \ + (CONFIG_ETRAX_SER##line##_##pinname##_ON_PB_BIT >= 0)? \ + (R_PORT_PB_DATA):&dummy_ser[line])) + +#define E100_STRUCT_SHADOW(line, pinname) \ + ((CONFIG_ETRAX_SER##line##_##pinname##_ON_PA_BIT >= 0)? \ + (&port_pa_data_shadow): ( \ + (CONFIG_ETRAX_SER##line##_##pinname##_ON_PB_BIT >= 0)? \ + (&port_pb_data_shadow):&dummy_ser[line])) +#define E100_STRUCT_MASK(line, pinname) \ + ((CONFIG_ETRAX_SER##line##_##pinname##_ON_PA_BIT >= 0)? \ + (1<<CONFIG_ETRAX_SER##line##_##pinname##_ON_PA_BIT): ( \ + (CONFIG_ETRAX_SER##line##_##pinname##_ON_PB_BIT >= 0)? \ + (1<<CONFIG_ETRAX_SER##line##_##pinname##_ON_PB_BIT):DUMMY_##pinname##_MASK)) + +#define DUMMY_DTR_MASK 1 +#define DUMMY_RI_MASK 2 +#define DUMMY_DSR_MASK 4 +#define DUMMY_CD_MASK 8 +static unsigned char dummy_ser[NR_PORTS] = {0xFF, 0xFF, 0xFF,0xFF}; + +/* If not all status pins are used or disabled, use mixed mode */ +#ifdef CONFIG_ETRAX_SERIAL_PORT0 + +#define SER0_PA_BITSUM (CONFIG_ETRAX_SER0_DTR_ON_PA_BIT+CONFIG_ETRAX_SER0_RI_ON_PA_BIT+CONFIG_ETRAX_SER0_DSR_ON_PA_BIT+CONFIG_ETRAX_SER0_CD_ON_PA_BIT) + +#if SER0_PA_BITSUM != -4 +# if CONFIG_ETRAX_SER0_DTR_ON_PA_BIT == -1 +# ifndef CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED +# define CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED 1 +# endif +# endif +# if CONFIG_ETRAX_SER0_RI_ON_PA_BIT == -1 +# ifndef CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED +# define CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED 1 +# endif +# endif +# if CONFIG_ETRAX_SER0_DSR_ON_PA_BIT == -1 +# ifndef CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED +# define CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED 1 +# endif +# endif +# if CONFIG_ETRAX_SER0_CD_ON_PA_BIT == -1 +# ifndef CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED +# define CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED 1 +# endif +# endif +#endif + +#define SER0_PB_BITSUM (CONFIG_ETRAX_SER0_DTR_ON_PB_BIT+CONFIG_ETRAX_SER0_RI_ON_PB_BIT+CONFIG_ETRAX_SER0_DSR_ON_PB_BIT+CONFIG_ETRAX_SER0_CD_ON_PB_BIT) + +#if SER0_PB_BITSUM != -4 +# if CONFIG_ETRAX_SER0_DTR_ON_PB_BIT == -1 +# ifndef CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED +# define CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED 1 +# endif +# endif +# if CONFIG_ETRAX_SER0_RI_ON_PB_BIT == -1 +# ifndef CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED +# define CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED 1 +# endif +# endif +# if CONFIG_ETRAX_SER0_DSR_ON_PB_BIT == -1 +# ifndef CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED +# define CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED 1 +# endif +# endif +# if CONFIG_ETRAX_SER0_CD_ON_PB_BIT == -1 +# ifndef CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED +# define CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED 1 +# endif +# endif +#endif + +#endif /* PORT0 */ + + +#ifdef CONFIG_ETRAX_SERIAL_PORT1 + +#define SER1_PA_BITSUM (CONFIG_ETRAX_SER1_DTR_ON_PA_BIT+CONFIG_ETRAX_SER1_RI_ON_PA_BIT+CONFIG_ETRAX_SER1_DSR_ON_PA_BIT+CONFIG_ETRAX_SER1_CD_ON_PA_BIT) + +#if SER1_PA_BITSUM != -4 +# if CONFIG_ETRAX_SER1_DTR_ON_PA_BIT == -1 +# ifndef CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED +# define CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED 1 +# endif +# endif +# if CONFIG_ETRAX_SER1_RI_ON_PA_BIT == -1 +# ifndef CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED +# define CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED 1 +# endif +# endif +# if CONFIG_ETRAX_SER1_DSR_ON_PA_BIT == -1 +# ifndef CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED +# define CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED 1 +# endif +# endif +# if CONFIG_ETRAX_SER1_CD_ON_PA_BIT == -1 +# ifndef CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED +# define CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED 1 +# endif +# endif +#endif + +#define SER1_PB_BITSUM (CONFIG_ETRAX_SER1_DTR_ON_PB_BIT+CONFIG_ETRAX_SER1_RI_ON_PB_BIT+CONFIG_ETRAX_SER1_DSR_ON_PB_BIT+CONFIG_ETRAX_SER1_CD_ON_PB_BIT) + +#if SER1_PB_BITSUM != -4 +# if CONFIG_ETRAX_SER1_DTR_ON_PB_BIT == -1 +# ifndef CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED +# define CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED 1 +# endif +# endif +# if CONFIG_ETRAX_SER1_RI_ON_PB_BIT == -1 +# ifndef CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED +# define CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED 1 +# endif +# endif +# if CONFIG_ETRAX_SER1_DSR_ON_PB_BIT == -1 +# ifndef CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED +# define CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED 1 +# endif +# endif +# if CONFIG_ETRAX_SER1_CD_ON_PB_BIT == -1 +# ifndef CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED +# define CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED 1 +# endif +# endif +#endif + +#endif /* PORT1 */ + +#ifdef CONFIG_ETRAX_SERIAL_PORT2 + +#define SER2_PA_BITSUM (CONFIG_ETRAX_SER2_DTR_ON_PA_BIT+CONFIG_ETRAX_SER2_RI_ON_PA_BIT+CONFIG_ETRAX_SER2_DSR_ON_PA_BIT+CONFIG_ETRAX_SER2_CD_ON_PA_BIT) + +#if SER2_PA_BITSUM != -4 +# if CONFIG_ETRAX_SER2_DTR_ON_PA_BIT == -1 +# ifndef CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED +# define CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED 1 +# endif +# endif +# if CONFIG_ETRAX_SER2_RI_ON_PA_BIT == -1 +# ifndef CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED +# define CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED 1 +# endif +# endif +# if CONFIG_ETRAX_SER2_DSR_ON_PA_BIT == -1 +# ifndef CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED +# define CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED 1 +# endif +# endif +# if CONFIG_ETRAX_SER2_CD_ON_PA_BIT == -1 +# ifndef CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED +# define CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED 1 +# endif +# endif +#endif + +#define SER2_PB_BITSUM (CONFIG_ETRAX_SER2_DTR_ON_PB_BIT+CONFIG_ETRAX_SER2_RI_ON_PB_BIT+CONFIG_ETRAX_SER2_DSR_ON_PB_BIT+CONFIG_ETRAX_SER2_CD_ON_PB_BIT) + +#if SER2_PB_BITSUM != -4 +# if CONFIG_ETRAX_SER2_DTR_ON_PB_BIT == -1 +# ifndef CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED +# define CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED 1 +# endif +# endif +# if CONFIG_ETRAX_SER2_RI_ON_PB_BIT == -1 +# ifndef CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED +# define CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED 1 +# endif +# endif +# if CONFIG_ETRAX_SER2_DSR_ON_PB_BIT == -1 +# ifndef CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED +# define CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED 1 +# endif +# endif +# if CONFIG_ETRAX_SER2_CD_ON_PB_BIT == -1 +# ifndef CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED +# define CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED 1 +# endif +# endif +#endif + +#endif /* PORT2 */ + +#ifdef CONFIG_ETRAX_SERIAL_PORT3 + +#define SER3_PA_BITSUM (CONFIG_ETRAX_SER3_DTR_ON_PA_BIT+CONFIG_ETRAX_SER3_RI_ON_PA_BIT+CONFIG_ETRAX_SER3_DSR_ON_PA_BIT+CONFIG_ETRAX_SER3_CD_ON_PA_BIT) + +#if SER3_PA_BITSUM != -4 +# if CONFIG_ETRAX_SER3_DTR_ON_PA_BIT == -1 +# ifndef CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED +# define CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED 1 +# endif +# endif +# if CONFIG_ETRAX_SER3_RI_ON_PA_BIT == -1 +# ifndef CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED +# define CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED 1 +# endif +# endif +# if CONFIG_ETRAX_SER3_DSR_ON_PA_BIT == -1 +# ifndef CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED +# define CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED 1 +# endif +# endif +# if CONFIG_ETRAX_SER3_CD_ON_PA_BIT == -1 +# ifndef CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED +# define CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED 1 +# endif +# endif +#endif + +#define SER3_PB_BITSUM (CONFIG_ETRAX_SER3_DTR_ON_PB_BIT+CONFIG_ETRAX_SER3_RI_ON_PB_BIT+CONFIG_ETRAX_SER3_DSR_ON_PB_BIT+CONFIG_ETRAX_SER3_CD_ON_PB_BIT) + +#if SER3_PB_BITSUM != -4 +# if CONFIG_ETRAX_SER3_DTR_ON_PB_BIT == -1 +# ifndef CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED +# define CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED 1 +# endif +# endif +# if CONFIG_ETRAX_SER3_RI_ON_PB_BIT == -1 +# ifndef CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED +# define CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED 1 +# endif +# endif +# if CONFIG_ETRAX_SER3_DSR_ON_PB_BIT == -1 +# ifndef CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED +# define CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED 1 +# endif +# endif +# if CONFIG_ETRAX_SER3_CD_ON_PB_BIT == -1 +# ifndef CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED +# define CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED 1 +# endif +# endif +#endif + +#endif /* PORT3 */ + + +#if defined(CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED) || \ + defined(CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED) || \ + defined(CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED) || \ + defined(CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED) +#define CONFIG_ETRAX_SERX_DTR_RI_DSR_CD_MIXED +#endif + +#ifdef CONFIG_ETRAX_SERX_DTR_RI_DSR_CD_MIXED +/* The pins can be mixed on PA and PB */ +#define CONTROL_PINS_PORT_NOT_USED(line) \ + &dummy_ser[line], &dummy_ser[line], \ + &dummy_ser[line], &dummy_ser[line], \ + &dummy_ser[line], &dummy_ser[line], \ + &dummy_ser[line], &dummy_ser[line], \ + DUMMY_DTR_MASK, DUMMY_RI_MASK, DUMMY_DSR_MASK, DUMMY_CD_MASK + + +struct control_pins +{ + volatile unsigned char *dtr_port; + unsigned char *dtr_shadow; + volatile unsigned char *ri_port; + unsigned char *ri_shadow; + volatile unsigned char *dsr_port; + unsigned char *dsr_shadow; + volatile unsigned char *cd_port; + unsigned char *cd_shadow; + + unsigned char dtr_mask; + unsigned char ri_mask; + unsigned char dsr_mask; + unsigned char cd_mask; +}; + +static const struct control_pins e100_modem_pins[NR_PORTS] = +{ + /* Ser 0 */ + { +#ifdef CONFIG_ETRAX_SERIAL_PORT0 + E100_STRUCT_PORT(0,DTR), E100_STRUCT_SHADOW(0,DTR), + E100_STRUCT_PORT(0,RI), E100_STRUCT_SHADOW(0,RI), + E100_STRUCT_PORT(0,DSR), E100_STRUCT_SHADOW(0,DSR), + E100_STRUCT_PORT(0,CD), E100_STRUCT_SHADOW(0,CD), + E100_STRUCT_MASK(0,DTR), + E100_STRUCT_MASK(0,RI), + E100_STRUCT_MASK(0,DSR), + E100_STRUCT_MASK(0,CD) +#else + CONTROL_PINS_PORT_NOT_USED(0) +#endif + }, + + /* Ser 1 */ + { +#ifdef CONFIG_ETRAX_SERIAL_PORT1 + E100_STRUCT_PORT(1,DTR), E100_STRUCT_SHADOW(1,DTR), + E100_STRUCT_PORT(1,RI), E100_STRUCT_SHADOW(1,RI), + E100_STRUCT_PORT(1,DSR), E100_STRUCT_SHADOW(1,DSR), + E100_STRUCT_PORT(1,CD), E100_STRUCT_SHADOW(1,CD), + E100_STRUCT_MASK(1,DTR), + E100_STRUCT_MASK(1,RI), + E100_STRUCT_MASK(1,DSR), + E100_STRUCT_MASK(1,CD) +#else + CONTROL_PINS_PORT_NOT_USED(1) +#endif + }, + + /* Ser 2 */ + { +#ifdef CONFIG_ETRAX_SERIAL_PORT2 + E100_STRUCT_PORT(2,DTR), E100_STRUCT_SHADOW(2,DTR), + E100_STRUCT_PORT(2,RI), E100_STRUCT_SHADOW(2,RI), + E100_STRUCT_PORT(2,DSR), E100_STRUCT_SHADOW(2,DSR), + E100_STRUCT_PORT(2,CD), E100_STRUCT_SHADOW(2,CD), + E100_STRUCT_MASK(2,DTR), + E100_STRUCT_MASK(2,RI), + E100_STRUCT_MASK(2,DSR), + E100_STRUCT_MASK(2,CD) +#else + CONTROL_PINS_PORT_NOT_USED(2) +#endif + }, + + /* Ser 3 */ + { +#ifdef CONFIG_ETRAX_SERIAL_PORT3 + E100_STRUCT_PORT(3,DTR), E100_STRUCT_SHADOW(3,DTR), + E100_STRUCT_PORT(3,RI), E100_STRUCT_SHADOW(3,RI), + E100_STRUCT_PORT(3,DSR), E100_STRUCT_SHADOW(3,DSR), + E100_STRUCT_PORT(3,CD), E100_STRUCT_SHADOW(3,CD), + E100_STRUCT_MASK(3,DTR), + E100_STRUCT_MASK(3,RI), + E100_STRUCT_MASK(3,DSR), + E100_STRUCT_MASK(3,CD) +#else + CONTROL_PINS_PORT_NOT_USED(3) +#endif + } +}; +#else /* CONFIG_ETRAX_SERX_DTR_RI_DSR_CD_MIXED */ + +/* All pins are on either PA or PB for each serial port */ +#define CONTROL_PINS_PORT_NOT_USED(line) \ + &dummy_ser[line], &dummy_ser[line], \ + DUMMY_DTR_MASK, DUMMY_RI_MASK, DUMMY_DSR_MASK, DUMMY_CD_MASK + + +struct control_pins +{ + volatile unsigned char *port; + unsigned char *shadow; + + unsigned char dtr_mask; + unsigned char ri_mask; + unsigned char dsr_mask; + unsigned char cd_mask; +}; + +#define dtr_port port +#define dtr_shadow shadow +#define ri_port port +#define ri_shadow shadow +#define dsr_port port +#define dsr_shadow shadow +#define cd_port port +#define cd_shadow shadow + +static const struct control_pins e100_modem_pins[NR_PORTS] = +{ + /* Ser 0 */ + { +#ifdef CONFIG_ETRAX_SERIAL_PORT0 + E100_STRUCT_PORT(0,DTR), E100_STRUCT_SHADOW(0,DTR), + E100_STRUCT_MASK(0,DTR), + E100_STRUCT_MASK(0,RI), + E100_STRUCT_MASK(0,DSR), + E100_STRUCT_MASK(0,CD) +#else + CONTROL_PINS_PORT_NOT_USED(0) +#endif + }, + + /* Ser 1 */ + { +#ifdef CONFIG_ETRAX_SERIAL_PORT1 + E100_STRUCT_PORT(1,DTR), E100_STRUCT_SHADOW(1,DTR), + E100_STRUCT_MASK(1,DTR), + E100_STRUCT_MASK(1,RI), + E100_STRUCT_MASK(1,DSR), + E100_STRUCT_MASK(1,CD) +#else + CONTROL_PINS_PORT_NOT_USED(1) +#endif + }, + + /* Ser 2 */ + { +#ifdef CONFIG_ETRAX_SERIAL_PORT2 + E100_STRUCT_PORT(2,DTR), E100_STRUCT_SHADOW(2,DTR), + E100_STRUCT_MASK(2,DTR), + E100_STRUCT_MASK(2,RI), + E100_STRUCT_MASK(2,DSR), + E100_STRUCT_MASK(2,CD) +#else + CONTROL_PINS_PORT_NOT_USED(2) +#endif + }, + + /* Ser 3 */ + { +#ifdef CONFIG_ETRAX_SERIAL_PORT3 + E100_STRUCT_PORT(3,DTR), E100_STRUCT_SHADOW(3,DTR), + E100_STRUCT_MASK(3,DTR), + E100_STRUCT_MASK(3,RI), + E100_STRUCT_MASK(3,DSR), + E100_STRUCT_MASK(3,CD) +#else + CONTROL_PINS_PORT_NOT_USED(3) +#endif + } +}; +#endif /* !CONFIG_ETRAX_SERX_DTR_RI_DSR_CD_MIXED */ + +#define E100_RTS_MASK 0x20 +#define E100_CTS_MASK 0x40 + +/* All serial port signals are active low: + * active = 0 -> 3.3V to RS-232 driver -> -12V on RS-232 level + * inactive = 1 -> 0V to RS-232 driver -> +12V on RS-232 level + * + * These macros returns the pin value: 0=0V, >=1 = 3.3V on ETRAX chip + */ + +/* Output */ +#define E100_RTS_GET(info) ((info)->rx_ctrl & E100_RTS_MASK) +/* Input */ +#define E100_CTS_GET(info) ((info)->ioport[REG_STATUS] & E100_CTS_MASK) + +/* These are typically PA or PB and 0 means 0V, 1 means 3.3V */ +/* Is an output */ +#define E100_DTR_GET(info) ((*e100_modem_pins[(info)->line].dtr_shadow) & e100_modem_pins[(info)->line].dtr_mask) + +/* Normally inputs */ +#define E100_RI_GET(info) ((*e100_modem_pins[(info)->line].ri_port) & e100_modem_pins[(info)->line].ri_mask) +#define E100_CD_GET(info) ((*e100_modem_pins[(info)->line].cd_port) & e100_modem_pins[(info)->line].cd_mask) + +/* Input */ +#define E100_DSR_GET(info) ((*e100_modem_pins[(info)->line].dsr_port) & e100_modem_pins[(info)->line].dsr_mask) + +/* Calculate the chartime depending on baudrate, numbor of bits etc. */ +static void update_char_time(struct e100_serial * info) +{ + tcflag_t cflags = info->port.tty->termios.c_cflag; + int bits; + + /* calc. number of bits / data byte */ + /* databits + startbit and 1 stopbit */ + if ((cflags & CSIZE) == CS7) + bits = 9; + else + bits = 10; + + if (cflags & CSTOPB) /* 2 stopbits ? */ + bits++; + + if (cflags & PARENB) /* parity bit ? */ + bits++; + + /* calc timeout */ + info->char_time_usec = ((bits * 1000000) / info->baud) + 1; + info->flush_time_usec = 4*info->char_time_usec; + if (info->flush_time_usec < MIN_FLUSH_TIME_USEC) + info->flush_time_usec = MIN_FLUSH_TIME_USEC; + +} + +/* + * This function maps from the Bxxxx defines in asm/termbits.h into real + * baud rates. + */ + +static int +cflag_to_baud(unsigned int cflag) +{ + static int baud_table[] = { + 0, 50, 75, 110, 134, 150, 200, 300, 600, 1200, 1800, 2400, + 4800, 9600, 19200, 38400 }; + + static int ext_baud_table[] = { + 0, 57600, 115200, 230400, 460800, 921600, 1843200, 6250000, + 0, 0, 0, 0, 0, 0, 0, 0 }; + + if (cflag & CBAUDEX) + return ext_baud_table[(cflag & CBAUD) & ~CBAUDEX]; + else + return baud_table[cflag & CBAUD]; +} + +/* and this maps to an etrax100 hardware baud constant */ + +static unsigned char +cflag_to_etrax_baud(unsigned int cflag) +{ + char retval; + + static char baud_table[] = { + -1, -1, -1, -1, -1, -1, -1, 0, 1, 2, -1, 3, 4, 5, 6, 7 }; + + static char ext_baud_table[] = { + -1, 8, 9, 10, 11, 12, 13, 14, -1, -1, -1, -1, -1, -1, -1, -1 }; + + if (cflag & CBAUDEX) + retval = ext_baud_table[(cflag & CBAUD) & ~CBAUDEX]; + else + retval = baud_table[cflag & CBAUD]; + + if (retval < 0) { + printk(KERN_WARNING "serdriver tried setting invalid baud rate, flags %x.\n", cflag); + retval = 5; /* choose default 9600 instead */ + } + + return retval | (retval << 4); /* choose same for both TX and RX */ +} + + +/* Various static support functions */ + +/* Functions to set or clear DTR/RTS on the requested line */ +/* It is complicated by the fact that RTS is a serial port register, while + * DTR might not be implemented in the HW at all, and if it is, it can be on + * any general port. + */ + + +static inline void +e100_dtr(struct e100_serial *info, int set) +{ + unsigned char mask = e100_modem_pins[info->line].dtr_mask; + +#ifdef SERIAL_DEBUG_IO + printk("ser%i dtr %i mask: 0x%02X\n", info->line, set, mask); + printk("ser%i shadow before 0x%02X get: %i\n", + info->line, *e100_modem_pins[info->line].dtr_shadow, + E100_DTR_GET(info)); +#endif + /* DTR is active low */ + { + unsigned long flags; + + local_irq_save(flags); + *e100_modem_pins[info->line].dtr_shadow &= ~mask; + *e100_modem_pins[info->line].dtr_shadow |= (set ? 0 : mask); + *e100_modem_pins[info->line].dtr_port = *e100_modem_pins[info->line].dtr_shadow; + local_irq_restore(flags); + } + +#ifdef SERIAL_DEBUG_IO + printk("ser%i shadow after 0x%02X get: %i\n", + info->line, *e100_modem_pins[info->line].dtr_shadow, + E100_DTR_GET(info)); +#endif +} + +/* set = 0 means 3.3V on the pin, bitvalue: 0=active, 1=inactive + * 0=0V , 1=3.3V + */ +static inline void +e100_rts(struct e100_serial *info, int set) +{ + unsigned long flags; + local_irq_save(flags); + info->rx_ctrl &= ~E100_RTS_MASK; + info->rx_ctrl |= (set ? 0 : E100_RTS_MASK); /* RTS is active low */ + info->ioport[REG_REC_CTRL] = info->rx_ctrl; + local_irq_restore(flags); +#ifdef SERIAL_DEBUG_IO + printk("ser%i rts %i\n", info->line, set); +#endif +} + + +/* If this behaves as a modem, RI and CD is an output */ +static inline void +e100_ri_out(struct e100_serial *info, int set) +{ + /* RI is active low */ + { + unsigned char mask = e100_modem_pins[info->line].ri_mask; + unsigned long flags; + + local_irq_save(flags); + *e100_modem_pins[info->line].ri_shadow &= ~mask; + *e100_modem_pins[info->line].ri_shadow |= (set ? 0 : mask); + *e100_modem_pins[info->line].ri_port = *e100_modem_pins[info->line].ri_shadow; + local_irq_restore(flags); + } +} +static inline void +e100_cd_out(struct e100_serial *info, int set) +{ + /* CD is active low */ + { + unsigned char mask = e100_modem_pins[info->line].cd_mask; + unsigned long flags; + + local_irq_save(flags); + *e100_modem_pins[info->line].cd_shadow &= ~mask; + *e100_modem_pins[info->line].cd_shadow |= (set ? 0 : mask); + *e100_modem_pins[info->line].cd_port = *e100_modem_pins[info->line].cd_shadow; + local_irq_restore(flags); + } +} + +static inline void +e100_disable_rx(struct e100_serial *info) +{ + /* disable the receiver */ + info->ioport[REG_REC_CTRL] = + (info->rx_ctrl &= ~IO_MASK(R_SERIAL0_REC_CTRL, rec_enable)); +} + +static inline void +e100_enable_rx(struct e100_serial *info) +{ + /* enable the receiver */ + info->ioport[REG_REC_CTRL] = + (info->rx_ctrl |= IO_MASK(R_SERIAL0_REC_CTRL, rec_enable)); +} + +/* the rx DMA uses both the dma_descr and the dma_eop interrupts */ + +static inline void +e100_disable_rxdma_irq(struct e100_serial *info) +{ +#ifdef SERIAL_DEBUG_INTR + printk("rxdma_irq(%d): 0\n",info->line); +#endif + DINTR1(DEBUG_LOG(info->line,"IRQ disable_rxdma_irq %i\n", info->line)); + *R_IRQ_MASK2_CLR = (info->irq << 2) | (info->irq << 3); +} + +static inline void +e100_enable_rxdma_irq(struct e100_serial *info) +{ +#ifdef SERIAL_DEBUG_INTR + printk("rxdma_irq(%d): 1\n",info->line); +#endif + DINTR1(DEBUG_LOG(info->line,"IRQ enable_rxdma_irq %i\n", info->line)); + *R_IRQ_MASK2_SET = (info->irq << 2) | (info->irq << 3); +} + +/* the tx DMA uses only dma_descr interrupt */ + +static void e100_disable_txdma_irq(struct e100_serial *info) +{ +#ifdef SERIAL_DEBUG_INTR + printk("txdma_irq(%d): 0\n",info->line); +#endif + DINTR1(DEBUG_LOG(info->line,"IRQ disable_txdma_irq %i\n", info->line)); + *R_IRQ_MASK2_CLR = info->irq; +} + +static void e100_enable_txdma_irq(struct e100_serial *info) +{ +#ifdef SERIAL_DEBUG_INTR + printk("txdma_irq(%d): 1\n",info->line); +#endif + DINTR1(DEBUG_LOG(info->line,"IRQ enable_txdma_irq %i\n", info->line)); + *R_IRQ_MASK2_SET = info->irq; +} + +static void e100_disable_txdma_channel(struct e100_serial *info) +{ + unsigned long flags; + + /* Disable output DMA channel for the serial port in question + * ( set to something other than serialX) + */ + local_irq_save(flags); + DFLOW(DEBUG_LOG(info->line, "disable_txdma_channel %i\n", info->line)); + if (info->line == 0) { + if ((genconfig_shadow & IO_MASK(R_GEN_CONFIG, dma6)) == + IO_STATE(R_GEN_CONFIG, dma6, serial0)) { + genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, dma6); + genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma6, unused); + } + } else if (info->line == 1) { + if ((genconfig_shadow & IO_MASK(R_GEN_CONFIG, dma8)) == + IO_STATE(R_GEN_CONFIG, dma8, serial1)) { + genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, dma8); + genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma8, usb); + } + } else if (info->line == 2) { + if ((genconfig_shadow & IO_MASK(R_GEN_CONFIG, dma2)) == + IO_STATE(R_GEN_CONFIG, dma2, serial2)) { + genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, dma2); + genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma2, par0); + } + } else if (info->line == 3) { + if ((genconfig_shadow & IO_MASK(R_GEN_CONFIG, dma4)) == + IO_STATE(R_GEN_CONFIG, dma4, serial3)) { + genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, dma4); + genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma4, par1); + } + } + *R_GEN_CONFIG = genconfig_shadow; + local_irq_restore(flags); +} + + +static void e100_enable_txdma_channel(struct e100_serial *info) +{ + unsigned long flags; + + local_irq_save(flags); + DFLOW(DEBUG_LOG(info->line, "enable_txdma_channel %i\n", info->line)); + /* Enable output DMA channel for the serial port in question */ + if (info->line == 0) { + genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, dma6); + genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma6, serial0); + } else if (info->line == 1) { + genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, dma8); + genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma8, serial1); + } else if (info->line == 2) { + genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, dma2); + genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma2, serial2); + } else if (info->line == 3) { + genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, dma4); + genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma4, serial3); + } + *R_GEN_CONFIG = genconfig_shadow; + local_irq_restore(flags); +} + +static void e100_disable_rxdma_channel(struct e100_serial *info) +{ + unsigned long flags; + + /* Disable input DMA channel for the serial port in question + * ( set to something other than serialX) + */ + local_irq_save(flags); + if (info->line == 0) { + if ((genconfig_shadow & IO_MASK(R_GEN_CONFIG, dma7)) == + IO_STATE(R_GEN_CONFIG, dma7, serial0)) { + genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, dma7); + genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma7, unused); + } + } else if (info->line == 1) { + if ((genconfig_shadow & IO_MASK(R_GEN_CONFIG, dma9)) == + IO_STATE(R_GEN_CONFIG, dma9, serial1)) { + genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, dma9); + genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma9, usb); + } + } else if (info->line == 2) { + if ((genconfig_shadow & IO_MASK(R_GEN_CONFIG, dma3)) == + IO_STATE(R_GEN_CONFIG, dma3, serial2)) { + genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, dma3); + genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma3, par0); + } + } else if (info->line == 3) { + if ((genconfig_shadow & IO_MASK(R_GEN_CONFIG, dma5)) == + IO_STATE(R_GEN_CONFIG, dma5, serial3)) { + genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, dma5); + genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma5, par1); + } + } + *R_GEN_CONFIG = genconfig_shadow; + local_irq_restore(flags); +} + + +static void e100_enable_rxdma_channel(struct e100_serial *info) +{ + unsigned long flags; + + local_irq_save(flags); + /* Enable input DMA channel for the serial port in question */ + if (info->line == 0) { + genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, dma7); + genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma7, serial0); + } else if (info->line == 1) { + genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, dma9); + genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma9, serial1); + } else if (info->line == 2) { + genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, dma3); + genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma3, serial2); + } else if (info->line == 3) { + genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, dma5); + genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma5, serial3); + } + *R_GEN_CONFIG = genconfig_shadow; + local_irq_restore(flags); +} + +#ifdef SERIAL_HANDLE_EARLY_ERRORS +/* in order to detect and fix errors on the first byte + we have to use the serial interrupts as well. */ + +static inline void +e100_disable_serial_data_irq(struct e100_serial *info) +{ +#ifdef SERIAL_DEBUG_INTR + printk("ser_irq(%d): 0\n",info->line); +#endif + DINTR1(DEBUG_LOG(info->line,"IRQ disable data_irq %i\n", info->line)); + *R_IRQ_MASK1_CLR = (1U << (8+2*info->line)); +} + +static inline void +e100_enable_serial_data_irq(struct e100_serial *info) +{ +#ifdef SERIAL_DEBUG_INTR + printk("ser_irq(%d): 1\n",info->line); + printk("**** %d = %d\n", + (8+2*info->line), + (1U << (8+2*info->line))); +#endif + DINTR1(DEBUG_LOG(info->line,"IRQ enable data_irq %i\n", info->line)); + *R_IRQ_MASK1_SET = (1U << (8+2*info->line)); +} +#endif + +static inline void +e100_disable_serial_tx_ready_irq(struct e100_serial *info) +{ +#ifdef SERIAL_DEBUG_INTR + printk("ser_tx_irq(%d): 0\n",info->line); +#endif + DINTR1(DEBUG_LOG(info->line,"IRQ disable ready_irq %i\n", info->line)); + *R_IRQ_MASK1_CLR = (1U << (8+1+2*info->line)); +} + +static inline void +e100_enable_serial_tx_ready_irq(struct e100_serial *info) +{ +#ifdef SERIAL_DEBUG_INTR + printk("ser_tx_irq(%d): 1\n",info->line); + printk("**** %d = %d\n", + (8+1+2*info->line), + (1U << (8+1+2*info->line))); +#endif + DINTR2(DEBUG_LOG(info->line,"IRQ enable ready_irq %i\n", info->line)); + *R_IRQ_MASK1_SET = (1U << (8+1+2*info->line)); +} + +static inline void e100_enable_rx_irq(struct e100_serial *info) +{ + if (info->uses_dma_in) + e100_enable_rxdma_irq(info); + else + e100_enable_serial_data_irq(info); +} +static inline void e100_disable_rx_irq(struct e100_serial *info) +{ + if (info->uses_dma_in) + e100_disable_rxdma_irq(info); + else + e100_disable_serial_data_irq(info); +} + +#if defined(CONFIG_ETRAX_RS485) +/* Enable RS-485 mode on selected port. This is UGLY. */ +static int +e100_enable_rs485(struct tty_struct *tty, struct serial_rs485 *r) +{ + struct e100_serial * info = (struct e100_serial *)tty->driver_data; + +#if defined(CONFIG_ETRAX_RS485_ON_PA) + *R_PORT_PA_DATA = port_pa_data_shadow |= (1 << rs485_pa_bit); +#endif +#if defined(CONFIG_ETRAX_RS485_ON_PORT_G) + REG_SHADOW_SET(R_PORT_G_DATA, port_g_data_shadow, + rs485_port_g_bit, 1); +#endif +#if defined(CONFIG_ETRAX_RS485_LTC1387) + REG_SHADOW_SET(R_PORT_G_DATA, port_g_data_shadow, + CONFIG_ETRAX_RS485_LTC1387_DXEN_PORT_G_BIT, 1); + REG_SHADOW_SET(R_PORT_G_DATA, port_g_data_shadow, + CONFIG_ETRAX_RS485_LTC1387_RXEN_PORT_G_BIT, 1); +#endif + + info->rs485 = *r; + + /* Maximum delay before RTS equal to 1000 */ + if (info->rs485.delay_rts_before_send >= 1000) + info->rs485.delay_rts_before_send = 1000; + +/* printk("rts: on send = %i, after = %i, enabled = %i", + info->rs485.rts_on_send, + info->rs485.rts_after_sent, + info->rs485.enabled + ); +*/ + return 0; +} + +static int +e100_write_rs485(struct tty_struct *tty, + const unsigned char *buf, int count) +{ + struct e100_serial * info = (struct e100_serial *)tty->driver_data; + int old_value = (info->rs485.flags) & SER_RS485_ENABLED; + + /* rs485 is always implicitly enabled if we're using the ioctl() + * but it doesn't have to be set in the serial_rs485 + * (to be backward compatible with old apps) + * So we store, set and restore it. + */ + info->rs485.flags |= SER_RS485_ENABLED; + /* rs_write now deals with RS485 if enabled */ + count = rs_write(tty, buf, count); + if (!old_value) + info->rs485.flags &= ~(SER_RS485_ENABLED); + return count; +} + +#ifdef CONFIG_ETRAX_FAST_TIMER +/* Timer function to toggle RTS when using FAST_TIMER */ +static void rs485_toggle_rts_timer_function(unsigned long data) +{ + struct e100_serial *info = (struct e100_serial *)data; + + fast_timers_rs485[info->line].function = NULL; + e100_rts(info, (info->rs485.flags & SER_RS485_RTS_AFTER_SEND)); +#if defined(CONFIG_ETRAX_RS485_DISABLE_RECEIVER) + e100_enable_rx(info); + e100_enable_rx_irq(info); +#endif +} +#endif +#endif /* CONFIG_ETRAX_RS485 */ + +/* + * ------------------------------------------------------------ + * rs_stop() and rs_start() + * + * This routines are called before setting or resetting tty->stopped. + * They enable or disable transmitter using the XOFF registers, as necessary. + * ------------------------------------------------------------ + */ + +static void +rs_stop(struct tty_struct *tty) +{ + struct e100_serial *info = (struct e100_serial *)tty->driver_data; + if (info) { + unsigned long flags; + unsigned long xoff; + + local_irq_save(flags); + DFLOW(DEBUG_LOG(info->line, "XOFF rs_stop xmit %i\n", + CIRC_CNT(info->xmit.head, + info->xmit.tail,SERIAL_XMIT_SIZE))); + + xoff = IO_FIELD(R_SERIAL0_XOFF, xoff_char, + STOP_CHAR(info->port.tty)); + xoff |= IO_STATE(R_SERIAL0_XOFF, tx_stop, stop); + if (tty->termios.c_iflag & IXON ) { + xoff |= IO_STATE(R_SERIAL0_XOFF, auto_xoff, enable); + } + + *((unsigned long *)&info->ioport[REG_XOFF]) = xoff; + local_irq_restore(flags); + } +} + +static void +rs_start(struct tty_struct *tty) +{ + struct e100_serial *info = (struct e100_serial *)tty->driver_data; + if (info) { + unsigned long flags; + unsigned long xoff; + + local_irq_save(flags); + DFLOW(DEBUG_LOG(info->line, "XOFF rs_start xmit %i\n", + CIRC_CNT(info->xmit.head, + info->xmit.tail,SERIAL_XMIT_SIZE))); + xoff = IO_FIELD(R_SERIAL0_XOFF, xoff_char, STOP_CHAR(tty)); + xoff |= IO_STATE(R_SERIAL0_XOFF, tx_stop, enable); + if (tty->termios.c_iflag & IXON ) { + xoff |= IO_STATE(R_SERIAL0_XOFF, auto_xoff, enable); + } + + *((unsigned long *)&info->ioport[REG_XOFF]) = xoff; + if (!info->uses_dma_out && + info->xmit.head != info->xmit.tail && info->xmit.buf) + e100_enable_serial_tx_ready_irq(info); + + local_irq_restore(flags); + } +} + +/* + * ---------------------------------------------------------------------- + * + * Here starts the interrupt handling routines. All of the following + * subroutines are declared as inline and are folded into + * rs_interrupt(). They were separated out for readability's sake. + * + * Note: rs_interrupt() is a "fast" interrupt, which means that it + * runs with interrupts turned off. People who may want to modify + * rs_interrupt() should try to keep the interrupt handler as fast as + * possible. After you are done making modifications, it is not a bad + * idea to do: + * + * gcc -S -DKERNEL -Wall -Wstrict-prototypes -O6 -fomit-frame-pointer serial.c + * + * and look at the resulting assemble code in serial.s. + * + * - Ted Ts'o (tytso@mit.edu), 7-Mar-93 + * ----------------------------------------------------------------------- + */ + +/* + * This routine is used by the interrupt handler to schedule + * processing in the software interrupt portion of the driver. + */ +static void rs_sched_event(struct e100_serial *info, int event) +{ + if (info->event & (1 << event)) + return; + info->event |= 1 << event; + schedule_work(&info->work); +} + +/* The output DMA channel is free - use it to send as many chars as possible + * NOTES: + * We don't pay attention to info->x_char, which means if the TTY wants to + * use XON/XOFF it will set info->x_char but we won't send any X char! + * + * To implement this, we'd just start a DMA send of 1 byte pointing at a + * buffer containing the X char, and skip updating xmit. We'd also have to + * check if the last sent char was the X char when we enter this function + * the next time, to avoid updating xmit with the sent X value. + */ + +static void +transmit_chars_dma(struct e100_serial *info) +{ + unsigned int c, sentl; + struct etrax_dma_descr *descr; + + /* acknowledge both dma_descr and dma_eop irq in R_DMA_CHx_CLR_INTR */ + *info->oclrintradr = + IO_STATE(R_DMA_CH6_CLR_INTR, clr_descr, do) | + IO_STATE(R_DMA_CH6_CLR_INTR, clr_eop, do); + +#ifdef SERIAL_DEBUG_INTR + if (info->line == SERIAL_DEBUG_LINE) + printk("tc\n"); +#endif + if (!info->tr_running) { + /* weirdo... we shouldn't get here! */ + printk(KERN_WARNING "Achtung: transmit_chars_dma with !tr_running\n"); + return; + } + + descr = &info->tr_descr; + + /* first get the amount of bytes sent during the last DMA transfer, + and update xmit accordingly */ + + /* if the stop bit was not set, all data has been sent */ + if (!(descr->status & d_stop)) { + sentl = descr->sw_len; + } else + /* otherwise we find the amount of data sent here */ + sentl = descr->hw_len; + + DFLOW(DEBUG_LOG(info->line, "TX %i done\n", sentl)); + + /* update stats */ + info->icount.tx += sentl; + + /* update xmit buffer */ + info->xmit.tail = (info->xmit.tail + sentl) & (SERIAL_XMIT_SIZE - 1); + + /* if there is only a few chars left in the buf, wake up the blocked + write if any */ + if (CIRC_CNT(info->xmit.head, + info->xmit.tail, + SERIAL_XMIT_SIZE) < WAKEUP_CHARS) + rs_sched_event(info, RS_EVENT_WRITE_WAKEUP); + + /* find out the largest amount of consecutive bytes we want to send now */ + + c = CIRC_CNT_TO_END(info->xmit.head, info->xmit.tail, SERIAL_XMIT_SIZE); + + /* Don't send all in one DMA transfer - divide it so we wake up + * application before all is sent + */ + + if (c >= 4*WAKEUP_CHARS) + c = c/2; + + if (c <= 0) { + /* our job here is done, don't schedule any new DMA transfer */ + info->tr_running = 0; + +#if defined(CONFIG_ETRAX_RS485) && defined(CONFIG_ETRAX_FAST_TIMER) + if (info->rs485.flags & SER_RS485_ENABLED) { + /* Set a short timer to toggle RTS */ + start_one_shot_timer(&fast_timers_rs485[info->line], + rs485_toggle_rts_timer_function, + (unsigned long)info, + info->char_time_usec*2, + "RS-485"); + } +#endif /* RS485 */ + return; + } + + /* ok we can schedule a dma send of c chars starting at info->xmit.tail */ + /* set up the descriptor correctly for output */ + DFLOW(DEBUG_LOG(info->line, "TX %i\n", c)); + descr->ctrl = d_int | d_eol | d_wait; /* Wait needed for tty_wait_until_sent() */ + descr->sw_len = c; + descr->buf = virt_to_phys(info->xmit.buf + info->xmit.tail); + descr->status = 0; + + *info->ofirstadr = virt_to_phys(descr); /* write to R_DMAx_FIRST */ + *info->ocmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, start); + + /* DMA is now running (hopefully) */ +} /* transmit_chars_dma */ + +static void +start_transmit(struct e100_serial *info) +{ +#if 0 + if (info->line == SERIAL_DEBUG_LINE) + printk("x\n"); +#endif + + info->tr_descr.sw_len = 0; + info->tr_descr.hw_len = 0; + info->tr_descr.status = 0; + info->tr_running = 1; + if (info->uses_dma_out) + transmit_chars_dma(info); + else + e100_enable_serial_tx_ready_irq(info); +} /* start_transmit */ + +#ifdef CONFIG_ETRAX_SERIAL_FAST_TIMER +static int serial_fast_timer_started = 0; +static int serial_fast_timer_expired = 0; +static void flush_timeout_function(unsigned long data); +#define START_FLUSH_FAST_TIMER_TIME(info, string, usec) {\ + unsigned long timer_flags; \ + local_irq_save(timer_flags); \ + if (fast_timers[info->line].function == NULL) { \ + serial_fast_timer_started++; \ + TIMERD(DEBUG_LOG(info->line, "start_timer %i ", info->line)); \ + TIMERD(DEBUG_LOG(info->line, "num started: %i\n", serial_fast_timer_started)); \ + start_one_shot_timer(&fast_timers[info->line], \ + flush_timeout_function, \ + (unsigned long)info, \ + (usec), \ + string); \ + } \ + else { \ + TIMERD(DEBUG_LOG(info->line, "timer %i already running\n", info->line)); \ + } \ + local_irq_restore(timer_flags); \ +} +#define START_FLUSH_FAST_TIMER(info, string) START_FLUSH_FAST_TIMER_TIME(info, string, info->flush_time_usec) + +#else +#define START_FLUSH_FAST_TIMER_TIME(info, string, usec) +#define START_FLUSH_FAST_TIMER(info, string) +#endif + +static struct etrax_recv_buffer * +alloc_recv_buffer(unsigned int size) +{ + struct etrax_recv_buffer *buffer; + + if (!(buffer = kmalloc(sizeof *buffer + size, GFP_ATOMIC))) + return NULL; + + buffer->next = NULL; + buffer->length = 0; + buffer->error = TTY_NORMAL; + + return buffer; +} + +static void +append_recv_buffer(struct e100_serial *info, struct etrax_recv_buffer *buffer) +{ + unsigned long flags; + + local_irq_save(flags); + + if (!info->first_recv_buffer) + info->first_recv_buffer = buffer; + else + info->last_recv_buffer->next = buffer; + + info->last_recv_buffer = buffer; + + info->recv_cnt += buffer->length; + if (info->recv_cnt > info->max_recv_cnt) + info->max_recv_cnt = info->recv_cnt; + + local_irq_restore(flags); +} + +static int +add_char_and_flag(struct e100_serial *info, unsigned char data, unsigned char flag) +{ + struct etrax_recv_buffer *buffer; + if (info->uses_dma_in) { + if (!(buffer = alloc_recv_buffer(4))) + return 0; + + buffer->length = 1; + buffer->error = flag; + buffer->buffer[0] = data; + + append_recv_buffer(info, buffer); + + info->icount.rx++; + } else { + tty_insert_flip_char(&info->port, data, flag); + info->icount.rx++; + } + + return 1; +} + +static unsigned int handle_descr_data(struct e100_serial *info, + struct etrax_dma_descr *descr, + unsigned int recvl) +{ + struct etrax_recv_buffer *buffer = phys_to_virt(descr->buf) - sizeof *buffer; + + if (info->recv_cnt + recvl > 65536) { + printk(KERN_WARNING + "%s: Too much pending incoming serial data! Dropping %u bytes.\n", __func__, recvl); + return 0; + } + + buffer->length = recvl; + + if (info->errorcode == ERRCODE_SET_BREAK) + buffer->error = TTY_BREAK; + info->errorcode = 0; + + append_recv_buffer(info, buffer); + + if (!(buffer = alloc_recv_buffer(SERIAL_DESCR_BUF_SIZE))) + panic("%s: Failed to allocate memory for receive buffer!\n", __func__); + + descr->buf = virt_to_phys(buffer->buffer); + + return recvl; +} + +static unsigned int handle_all_descr_data(struct e100_serial *info) +{ + struct etrax_dma_descr *descr; + unsigned int recvl; + unsigned int ret = 0; + + while (1) + { + descr = &info->rec_descr[info->cur_rec_descr]; + + if (descr == phys_to_virt(*info->idescradr)) + break; + + if (++info->cur_rec_descr == SERIAL_RECV_DESCRIPTORS) + info->cur_rec_descr = 0; + + /* find out how many bytes were read */ + + /* if the eop bit was not set, all data has been received */ + if (!(descr->status & d_eop)) { + recvl = descr->sw_len; + } else { + /* otherwise we find the amount of data received here */ + recvl = descr->hw_len; + } + + /* Reset the status information */ + descr->status = 0; + + DFLOW( DEBUG_LOG(info->line, "RX %lu\n", recvl); + if (info->port.tty->stopped) { + unsigned char *buf = phys_to_virt(descr->buf); + DEBUG_LOG(info->line, "rx 0x%02X\n", buf[0]); + DEBUG_LOG(info->line, "rx 0x%02X\n", buf[1]); + DEBUG_LOG(info->line, "rx 0x%02X\n", buf[2]); + } + ); + + /* update stats */ + info->icount.rx += recvl; + + ret += handle_descr_data(info, descr, recvl); + } + + return ret; +} + +static void receive_chars_dma(struct e100_serial *info) +{ + struct tty_struct *tty; + unsigned char rstat; + + /* Acknowledge both dma_descr and dma_eop irq in R_DMA_CHx_CLR_INTR */ + *info->iclrintradr = + IO_STATE(R_DMA_CH6_CLR_INTR, clr_descr, do) | + IO_STATE(R_DMA_CH6_CLR_INTR, clr_eop, do); + + tty = info->port.tty; + if (!tty) /* Something wrong... */ + return; + +#ifdef SERIAL_HANDLE_EARLY_ERRORS + if (info->uses_dma_in) + e100_enable_serial_data_irq(info); +#endif + + if (info->errorcode == ERRCODE_INSERT_BREAK) + add_char_and_flag(info, '\0', TTY_BREAK); + + handle_all_descr_data(info); + + /* Read the status register to detect errors */ + rstat = info->ioport[REG_STATUS]; + if (rstat & IO_MASK(R_SERIAL0_STATUS, xoff_detect) ) { + DFLOW(DEBUG_LOG(info->line, "XOFF detect stat %x\n", rstat)); + } + + if (rstat & SER_ERROR_MASK) { + /* If we got an error, we must reset it by reading the + * data_in field + */ + unsigned char data = info->ioport[REG_DATA]; + + PROCSTAT(ser_stat[info->line].errors_cnt++); + DEBUG_LOG(info->line, "#dERR: s d 0x%04X\n", + ((rstat & SER_ERROR_MASK) << 8) | data); + + if (rstat & SER_PAR_ERR_MASK) + add_char_and_flag(info, data, TTY_PARITY); + else if (rstat & SER_OVERRUN_MASK) + add_char_and_flag(info, data, TTY_OVERRUN); + else if (rstat & SER_FRAMING_ERR_MASK) + add_char_and_flag(info, data, TTY_FRAME); + } + + START_FLUSH_FAST_TIMER(info, "receive_chars"); + + /* Restart the receiving DMA */ + *info->icmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, restart); +} + +static int start_recv_dma(struct e100_serial *info) +{ + struct etrax_dma_descr *descr = info->rec_descr; + struct etrax_recv_buffer *buffer; + int i; + + /* Set up the receiving descriptors */ + for (i = 0; i < SERIAL_RECV_DESCRIPTORS; i++) { + if (!(buffer = alloc_recv_buffer(SERIAL_DESCR_BUF_SIZE))) + panic("%s: Failed to allocate memory for receive buffer!\n", __func__); + + descr[i].ctrl = d_int; + descr[i].buf = virt_to_phys(buffer->buffer); + descr[i].sw_len = SERIAL_DESCR_BUF_SIZE; + descr[i].hw_len = 0; + descr[i].status = 0; + descr[i].next = virt_to_phys(&descr[i+1]); + } + + /* Link the last descriptor to the first */ + descr[i-1].next = virt_to_phys(&descr[0]); + + /* Start with the first descriptor in the list */ + info->cur_rec_descr = 0; + + /* Start the DMA */ + *info->ifirstadr = virt_to_phys(&descr[info->cur_rec_descr]); + *info->icmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, start); + + /* Input DMA should be running now */ + return 1; +} + +static void +start_receive(struct e100_serial *info) +{ + if (info->uses_dma_in) { + /* reset the input dma channel to be sure it works */ + + *info->icmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, reset); + while (IO_EXTRACT(R_DMA_CH6_CMD, cmd, *info->icmdadr) == + IO_STATE_VALUE(R_DMA_CH6_CMD, cmd, reset)); + + start_recv_dma(info); + } +} + + +/* the bits in the MASK2 register are laid out like this: + DMAI_EOP DMAI_DESCR DMAO_EOP DMAO_DESCR + where I is the input channel and O is the output channel for the port. + info->irq is the bit number for the DMAO_DESCR so to check the others we + shift info->irq to the left. +*/ + +/* dma output channel interrupt handler + this interrupt is called from DMA2(ser2), DMA4(ser3), DMA6(ser0) or + DMA8(ser1) when they have finished a descriptor with the intr flag set. +*/ + +static irqreturn_t +tr_interrupt(int irq, void *dev_id) +{ + struct e100_serial *info; + unsigned long ireg; + int i; + int handled = 0; + + /* find out the line that caused this irq and get it from rs_table */ + + ireg = *R_IRQ_MASK2_RD; /* get the active irq bits for the dma channels */ + + for (i = 0; i < NR_PORTS; i++) { + info = rs_table + i; + if (!info->enabled || !info->uses_dma_out) + continue; + /* check for dma_descr (don't need to check for dma_eop in output dma for serial */ + if (ireg & info->irq) { + handled = 1; + /* we can send a new dma bunch. make it so. */ + DINTR2(DEBUG_LOG(info->line, "tr_interrupt %i\n", i)); + /* Read jiffies_usec first, + * we want this time to be as late as possible + */ + PROCSTAT(ser_stat[info->line].tx_dma_ints++); + info->last_tx_active_usec = GET_JIFFIES_USEC(); + info->last_tx_active = jiffies; + transmit_chars_dma(info); + } + + /* FIXME: here we should really check for a change in the + status lines and if so call status_handle(info) */ + } + return IRQ_RETVAL(handled); +} /* tr_interrupt */ + +/* dma input channel interrupt handler */ + +static irqreturn_t +rec_interrupt(int irq, void *dev_id) +{ + struct e100_serial *info; + unsigned long ireg; + int i; + int handled = 0; + + /* find out the line that caused this irq and get it from rs_table */ + + ireg = *R_IRQ_MASK2_RD; /* get the active irq bits for the dma channels */ + + for (i = 0; i < NR_PORTS; i++) { + info = rs_table + i; + if (!info->enabled || !info->uses_dma_in) + continue; + /* check for both dma_eop and dma_descr for the input dma channel */ + if (ireg & ((info->irq << 2) | (info->irq << 3))) { + handled = 1; + /* we have received something */ + receive_chars_dma(info); + } + + /* FIXME: here we should really check for a change in the + status lines and if so call status_handle(info) */ + } + return IRQ_RETVAL(handled); +} /* rec_interrupt */ + +static int force_eop_if_needed(struct e100_serial *info) +{ + /* We check data_avail bit to determine if data has + * arrived since last time + */ + unsigned char rstat = info->ioport[REG_STATUS]; + + /* error or datavail? */ + if (rstat & SER_ERROR_MASK) { + /* Some error has occurred. If there has been valid data, an + * EOP interrupt will be made automatically. If no data, the + * normal ser_interrupt should be enabled and handle it. + * So do nothing! + */ + DEBUG_LOG(info->line, "timeout err: rstat 0x%03X\n", + rstat | (info->line << 8)); + return 0; + } + + if (rstat & SER_DATA_AVAIL_MASK) { + /* Ok data, no error, count it */ + TIMERD(DEBUG_LOG(info->line, "timeout: rstat 0x%03X\n", + rstat | (info->line << 8))); + /* Read data to clear status flags */ + (void)info->ioport[REG_DATA]; + + info->forced_eop = 0; + START_FLUSH_FAST_TIMER(info, "magic"); + return 0; + } + + /* hit the timeout, force an EOP for the input + * dma channel if we haven't already + */ + if (!info->forced_eop) { + info->forced_eop = 1; + PROCSTAT(ser_stat[info->line].timeout_flush_cnt++); + TIMERD(DEBUG_LOG(info->line, "timeout EOP %i\n", info->line)); + FORCE_EOP(info); + } + + return 1; +} + +static void flush_to_flip_buffer(struct e100_serial *info) +{ + struct etrax_recv_buffer *buffer; + unsigned long flags; + + local_irq_save(flags); + + while ((buffer = info->first_recv_buffer) != NULL) { + unsigned int count = buffer->length; + + tty_insert_flip_string(&info->port, buffer->buffer, count); + info->recv_cnt -= count; + + if (count == buffer->length) { + info->first_recv_buffer = buffer->next; + kfree(buffer); + } else { + buffer->length -= count; + memmove(buffer->buffer, buffer->buffer + count, buffer->length); + buffer->error = TTY_NORMAL; + } + } + + if (!info->first_recv_buffer) + info->last_recv_buffer = NULL; + + local_irq_restore(flags); + + /* This includes a check for low-latency */ + tty_flip_buffer_push(&info->port); +} + +static void check_flush_timeout(struct e100_serial *info) +{ + /* Flip what we've got (if we can) */ + flush_to_flip_buffer(info); + + /* We might need to flip later, but not to fast + * since the system is busy processing input... */ + if (info->first_recv_buffer) + START_FLUSH_FAST_TIMER_TIME(info, "flip", 2000); + + /* Force eop last, since data might have come while we're processing + * and if we started the slow timer above, we won't start a fast + * below. + */ + force_eop_if_needed(info); +} + +#ifdef CONFIG_ETRAX_SERIAL_FAST_TIMER +static void flush_timeout_function(unsigned long data) +{ + struct e100_serial *info = (struct e100_serial *)data; + + fast_timers[info->line].function = NULL; + serial_fast_timer_expired++; + TIMERD(DEBUG_LOG(info->line, "flush_timeout %i ", info->line)); + TIMERD(DEBUG_LOG(info->line, "num expired: %i\n", serial_fast_timer_expired)); + check_flush_timeout(info); +} + +#else + +/* dma fifo/buffer timeout handler + forces an end-of-packet for the dma input channel if no chars + have been received for CONFIG_ETRAX_SERIAL_RX_TIMEOUT_TICKS/100 s. +*/ + +static struct timer_list flush_timer; + +static void +timed_flush_handler(unsigned long ptr) +{ + struct e100_serial *info; + int i; + + for (i = 0; i < NR_PORTS; i++) { + info = rs_table + i; + if (info->uses_dma_in) + check_flush_timeout(info); + } + + /* restart flush timer */ + mod_timer(&flush_timer, jiffies + CONFIG_ETRAX_SERIAL_RX_TIMEOUT_TICKS); +} +#endif + +#ifdef SERIAL_HANDLE_EARLY_ERRORS + +/* If there is an error (ie break) when the DMA is running and + * there are no bytes in the fifo the DMA is stopped and we get no + * eop interrupt. Thus we have to monitor the first bytes on a DMA + * transfer, and if it is without error we can turn the serial + * interrupts off. + */ + +/* +BREAK handling on ETRAX 100: +ETRAX will generate interrupt although there is no stop bit between the +characters. + +Depending on how long the break sequence is, the end of the breaksequence +will look differently: +| indicates start/end of a character. + +B= Break character (0x00) with framing error. +E= Error byte with parity error received after B characters. +F= "Faked" valid byte received immediately after B characters. +V= Valid byte + +1. + B BL ___________________________ V +.._|__________|__________| |valid data | + +Multiple frame errors with data == 0x00 (B), +the timing matches up "perfectly" so no extra ending char is detected. +The RXD pin is 1 in the last interrupt, in that case +we set info->errorcode = ERRCODE_INSERT_BREAK, but we can't really +know if another byte will come and this really is case 2. below +(e.g F=0xFF or 0xFE) +If RXD pin is 0 we can expect another character (see 2. below). + + +2. + + B B E or F__________________..__ V +.._|__________|__________|______ | |valid data + "valid" or + parity error + +Multiple frame errors with data == 0x00 (B), +but the part of the break trigs is interpreted as a start bit (and possibly +some 0 bits followed by a number of 1 bits and a stop bit). +Depending on parity settings etc. this last character can be either +a fake "valid" char (F) or have a parity error (E). + +If the character is valid it will be put in the buffer, +we set info->errorcode = ERRCODE_SET_BREAK so the receive interrupt +will set the flags so the tty will handle it, +if it's an error byte it will not be put in the buffer +and we set info->errorcode = ERRCODE_INSERT_BREAK. + +To distinguish a V byte in 1. from an F byte in 2. we keep a timestamp +of the last faulty char (B) and compares it with the current time: +If the time elapsed time is less then 2*char_time_usec we will assume +it's a faked F char and not a Valid char and set +info->errorcode = ERRCODE_SET_BREAK. + +Flaws in the above solution: +~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +We use the timer to distinguish a F character from a V character, +if a V character is to close after the break we might make the wrong decision. + +TODO: The break will be delayed until an F or V character is received. + +*/ + +static void handle_ser_rx_interrupt_no_dma(struct e100_serial *info) +{ + unsigned long data_read; + + /* Read data and status at the same time */ + data_read = *((unsigned long *)&info->ioport[REG_DATA_STATUS32]); +more_data: + if (data_read & IO_MASK(R_SERIAL0_READ, xoff_detect) ) { + DFLOW(DEBUG_LOG(info->line, "XOFF detect\n", 0)); + } + DINTR2(DEBUG_LOG(info->line, "ser_rx %c\n", IO_EXTRACT(R_SERIAL0_READ, data_in, data_read))); + + if (data_read & ( IO_MASK(R_SERIAL0_READ, framing_err) | + IO_MASK(R_SERIAL0_READ, par_err) | + IO_MASK(R_SERIAL0_READ, overrun) )) { + /* An error */ + info->last_rx_active_usec = GET_JIFFIES_USEC(); + info->last_rx_active = jiffies; + DINTR1(DEBUG_LOG(info->line, "ser_rx err stat_data %04X\n", data_read)); + DLOG_INT_TRIG( + if (!log_int_trig1_pos) { + log_int_trig1_pos = log_int_pos; + log_int(rdpc(), 0, 0); + } + ); + + + if ( ((data_read & IO_MASK(R_SERIAL0_READ, data_in)) == 0) && + (data_read & IO_MASK(R_SERIAL0_READ, framing_err)) ) { + /* Most likely a break, but we get interrupts over and + * over again. + */ + + if (!info->break_detected_cnt) { + DEBUG_LOG(info->line, "#BRK start\n", 0); + } + if (data_read & IO_MASK(R_SERIAL0_READ, rxd)) { + /* The RX pin is high now, so the break + * must be over, but.... + * we can't really know if we will get another + * last byte ending the break or not. + * And we don't know if the byte (if any) will + * have an error or look valid. + */ + DEBUG_LOG(info->line, "# BL BRK\n", 0); + info->errorcode = ERRCODE_INSERT_BREAK; + } + info->break_detected_cnt++; + } else { + /* The error does not look like a break, but could be + * the end of one + */ + if (info->break_detected_cnt) { + DEBUG_LOG(info->line, "EBRK %i\n", info->break_detected_cnt); + info->errorcode = ERRCODE_INSERT_BREAK; + } else { + unsigned char data = IO_EXTRACT(R_SERIAL0_READ, + data_in, data_read); + char flag = TTY_NORMAL; + if (info->errorcode == ERRCODE_INSERT_BREAK) { + tty_insert_flip_char(&info->port, 0, flag); + info->icount.rx++; + } + + if (data_read & IO_MASK(R_SERIAL0_READ, par_err)) { + info->icount.parity++; + flag = TTY_PARITY; + } else if (data_read & IO_MASK(R_SERIAL0_READ, overrun)) { + info->icount.overrun++; + flag = TTY_OVERRUN; + } else if (data_read & IO_MASK(R_SERIAL0_READ, framing_err)) { + info->icount.frame++; + flag = TTY_FRAME; + } + tty_insert_flip_char(&info->port, data, flag); + info->errorcode = 0; + } + info->break_detected_cnt = 0; + } + } else if (data_read & IO_MASK(R_SERIAL0_READ, data_avail)) { + /* No error */ + DLOG_INT_TRIG( + if (!log_int_trig1_pos) { + if (log_int_pos >= log_int_size) { + log_int_pos = 0; + } + log_int_trig0_pos = log_int_pos; + log_int(rdpc(), 0, 0); + } + ); + tty_insert_flip_char(&info->port, + IO_EXTRACT(R_SERIAL0_READ, data_in, data_read), + TTY_NORMAL); + } else { + DEBUG_LOG(info->line, "ser_rx int but no data_avail %08lX\n", data_read); + } + + + info->icount.rx++; + data_read = *((unsigned long *)&info->ioport[REG_DATA_STATUS32]); + if (data_read & IO_MASK(R_SERIAL0_READ, data_avail)) { + DEBUG_LOG(info->line, "ser_rx %c in loop\n", IO_EXTRACT(R_SERIAL0_READ, data_in, data_read)); + goto more_data; + } + + tty_flip_buffer_push(&info->port); +} + +static void handle_ser_rx_interrupt(struct e100_serial *info) +{ + unsigned char rstat; + +#ifdef SERIAL_DEBUG_INTR + printk("Interrupt from serport %d\n", i); +#endif +/* DEBUG_LOG(info->line, "ser_interrupt stat %03X\n", rstat | (i << 8)); */ + if (!info->uses_dma_in) { + handle_ser_rx_interrupt_no_dma(info); + return; + } + /* DMA is used */ + rstat = info->ioport[REG_STATUS]; + if (rstat & IO_MASK(R_SERIAL0_STATUS, xoff_detect) ) { + DFLOW(DEBUG_LOG(info->line, "XOFF detect\n", 0)); + } + + if (rstat & SER_ERROR_MASK) { + unsigned char data; + + info->last_rx_active_usec = GET_JIFFIES_USEC(); + info->last_rx_active = jiffies; + /* If we got an error, we must reset it by reading the + * data_in field + */ + data = info->ioport[REG_DATA]; + DINTR1(DEBUG_LOG(info->line, "ser_rx! %c\n", data)); + DINTR1(DEBUG_LOG(info->line, "ser_rx err stat %02X\n", rstat)); + if (!data && (rstat & SER_FRAMING_ERR_MASK)) { + /* Most likely a break, but we get interrupts over and + * over again. + */ + + if (!info->break_detected_cnt) { + DEBUG_LOG(info->line, "#BRK start\n", 0); + } + if (rstat & SER_RXD_MASK) { + /* The RX pin is high now, so the break + * must be over, but.... + * we can't really know if we will get another + * last byte ending the break or not. + * And we don't know if the byte (if any) will + * have an error or look valid. + */ + DEBUG_LOG(info->line, "# BL BRK\n", 0); + info->errorcode = ERRCODE_INSERT_BREAK; + } + info->break_detected_cnt++; + } else { + /* The error does not look like a break, but could be + * the end of one + */ + if (info->break_detected_cnt) { + DEBUG_LOG(info->line, "EBRK %i\n", info->break_detected_cnt); + info->errorcode = ERRCODE_INSERT_BREAK; + } else { + if (info->errorcode == ERRCODE_INSERT_BREAK) { + info->icount.brk++; + add_char_and_flag(info, '\0', TTY_BREAK); + } + + if (rstat & SER_PAR_ERR_MASK) { + info->icount.parity++; + add_char_and_flag(info, data, TTY_PARITY); + } else if (rstat & SER_OVERRUN_MASK) { + info->icount.overrun++; + add_char_and_flag(info, data, TTY_OVERRUN); + } else if (rstat & SER_FRAMING_ERR_MASK) { + info->icount.frame++; + add_char_and_flag(info, data, TTY_FRAME); + } + + info->errorcode = 0; + } + info->break_detected_cnt = 0; + DEBUG_LOG(info->line, "#iERR s d %04X\n", + ((rstat & SER_ERROR_MASK) << 8) | data); + } + PROCSTAT(ser_stat[info->line].early_errors_cnt++); + } else { /* It was a valid byte, now let the DMA do the rest */ + unsigned long curr_time_u = GET_JIFFIES_USEC(); + unsigned long curr_time = jiffies; + + if (info->break_detected_cnt) { + /* Detect if this character is a new valid char or the + * last char in a break sequence: If LSBits are 0 and + * MSBits are high AND the time is close to the + * previous interrupt we should discard it. + */ + long elapsed_usec = + (curr_time - info->last_rx_active) * (1000000/HZ) + + curr_time_u - info->last_rx_active_usec; + if (elapsed_usec < 2*info->char_time_usec) { + DEBUG_LOG(info->line, "FBRK %i\n", info->line); + /* Report as BREAK (error) and let + * receive_chars_dma() handle it + */ + info->errorcode = ERRCODE_SET_BREAK; + } else { + DEBUG_LOG(info->line, "Not end of BRK (V)%i\n", info->line); + } + DEBUG_LOG(info->line, "num brk %i\n", info->break_detected_cnt); + } + +#ifdef SERIAL_DEBUG_INTR + printk("** OK, disabling ser_interrupts\n"); +#endif + e100_disable_serial_data_irq(info); + DINTR2(DEBUG_LOG(info->line, "ser_rx OK %d\n", info->line)); + info->break_detected_cnt = 0; + + PROCSTAT(ser_stat[info->line].ser_ints_ok_cnt++); + } + /* Restarting the DMA never hurts */ + *info->icmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, restart); + START_FLUSH_FAST_TIMER(info, "ser_int"); +} /* handle_ser_rx_interrupt */ + +static void handle_ser_tx_interrupt(struct e100_serial *info) +{ + unsigned long flags; + + if (info->x_char) { + unsigned char rstat; + DFLOW(DEBUG_LOG(info->line, "tx_int: xchar 0x%02X\n", info->x_char)); + local_irq_save(flags); + rstat = info->ioport[REG_STATUS]; + DFLOW(DEBUG_LOG(info->line, "stat %x\n", rstat)); + + info->ioport[REG_TR_DATA] = info->x_char; + info->icount.tx++; + info->x_char = 0; + /* We must enable since it is disabled in ser_interrupt */ + e100_enable_serial_tx_ready_irq(info); + local_irq_restore(flags); + return; + } + if (info->uses_dma_out) { + unsigned char rstat; + int i; + /* We only use normal tx interrupt when sending x_char */ + DFLOW(DEBUG_LOG(info->line, "tx_int: xchar sent\n", 0)); + local_irq_save(flags); + rstat = info->ioport[REG_STATUS]; + DFLOW(DEBUG_LOG(info->line, "stat %x\n", rstat)); + e100_disable_serial_tx_ready_irq(info); + if (info->port.tty->stopped) + rs_stop(info->port.tty); + /* Enable the DMA channel and tell it to continue */ + e100_enable_txdma_channel(info); + /* Wait 12 cycles before doing the DMA command */ + for(i = 6; i > 0; i--) + nop(); + + *info->ocmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, continue); + local_irq_restore(flags); + return; + } + /* Normal char-by-char interrupt */ + if (info->xmit.head == info->xmit.tail + || info->port.tty->stopped) { + DFLOW(DEBUG_LOG(info->line, "tx_int: stopped %i\n", + info->port.tty->stopped)); + e100_disable_serial_tx_ready_irq(info); + info->tr_running = 0; + return; + } + DINTR2(DEBUG_LOG(info->line, "tx_int %c\n", info->xmit.buf[info->xmit.tail])); + /* Send a byte, rs485 timing is critical so turn of ints */ + local_irq_save(flags); + info->ioport[REG_TR_DATA] = info->xmit.buf[info->xmit.tail]; + info->xmit.tail = (info->xmit.tail + 1) & (SERIAL_XMIT_SIZE-1); + info->icount.tx++; + if (info->xmit.head == info->xmit.tail) { +#if defined(CONFIG_ETRAX_RS485) && defined(CONFIG_ETRAX_FAST_TIMER) + if (info->rs485.flags & SER_RS485_ENABLED) { + /* Set a short timer to toggle RTS */ + start_one_shot_timer(&fast_timers_rs485[info->line], + rs485_toggle_rts_timer_function, + (unsigned long)info, + info->char_time_usec*2, + "RS-485"); + } +#endif /* RS485 */ + info->last_tx_active_usec = GET_JIFFIES_USEC(); + info->last_tx_active = jiffies; + e100_disable_serial_tx_ready_irq(info); + info->tr_running = 0; + DFLOW(DEBUG_LOG(info->line, "tx_int: stop2\n", 0)); + } else { + /* We must enable since it is disabled in ser_interrupt */ + e100_enable_serial_tx_ready_irq(info); + } + local_irq_restore(flags); + + if (CIRC_CNT(info->xmit.head, + info->xmit.tail, + SERIAL_XMIT_SIZE) < WAKEUP_CHARS) + rs_sched_event(info, RS_EVENT_WRITE_WAKEUP); + +} /* handle_ser_tx_interrupt */ + +/* result of time measurements: + * RX duration 54-60 us when doing something, otherwise 6-9 us + * ser_int duration: just sending: 8-15 us normally, up to 73 us + */ +static irqreturn_t +ser_interrupt(int irq, void *dev_id) +{ + static volatile int tx_started = 0; + struct e100_serial *info; + int i; + unsigned long flags; + unsigned long irq_mask1_rd; + unsigned long data_mask = (1 << (8+2*0)); /* ser0 data_avail */ + int handled = 0; + static volatile unsigned long reentered_ready_mask = 0; + + local_irq_save(flags); + irq_mask1_rd = *R_IRQ_MASK1_RD; + /* First handle all rx interrupts with ints disabled */ + info = rs_table; + irq_mask1_rd &= e100_ser_int_mask; + for (i = 0; i < NR_PORTS; i++) { + /* Which line caused the data irq? */ + if (irq_mask1_rd & data_mask) { + handled = 1; + handle_ser_rx_interrupt(info); + } + info += 1; + data_mask <<= 2; + } + /* Handle tx interrupts with interrupts enabled so we + * can take care of new data interrupts while transmitting + * We protect the tx part with the tx_started flag. + * We disable the tr_ready interrupts we are about to handle and + * unblock the serial interrupt so new serial interrupts may come. + * + * If we get a new interrupt: + * - it migth be due to synchronous serial ports. + * - serial irq will be blocked by general irq handler. + * - async data will be handled above (sync will be ignored). + * - tx_started flag will prevent us from trying to send again and + * we will exit fast - no need to unblock serial irq. + * - Next (sync) serial interrupt handler will be runned with + * disabled interrupt due to restore_flags() at end of function, + * so sync handler will not be preempted or reentered. + */ + if (!tx_started) { + unsigned long ready_mask; + unsigned long + tx_started = 1; + /* Only the tr_ready interrupts left */ + irq_mask1_rd &= (IO_MASK(R_IRQ_MASK1_RD, ser0_ready) | + IO_MASK(R_IRQ_MASK1_RD, ser1_ready) | + IO_MASK(R_IRQ_MASK1_RD, ser2_ready) | + IO_MASK(R_IRQ_MASK1_RD, ser3_ready)); + while (irq_mask1_rd) { + /* Disable those we are about to handle */ + *R_IRQ_MASK1_CLR = irq_mask1_rd; + /* Unblock the serial interrupt */ + *R_VECT_MASK_SET = IO_STATE(R_VECT_MASK_SET, serial, set); + + local_irq_enable(); + ready_mask = (1 << (8+1+2*0)); /* ser0 tr_ready */ + info = rs_table; + for (i = 0; i < NR_PORTS; i++) { + /* Which line caused the ready irq? */ + if (irq_mask1_rd & ready_mask) { + handled = 1; + handle_ser_tx_interrupt(info); + } + info += 1; + ready_mask <<= 2; + } + /* handle_ser_tx_interrupt enables tr_ready interrupts */ + local_irq_disable(); + /* Handle reentered TX interrupt */ + irq_mask1_rd = reentered_ready_mask; + } + local_irq_disable(); + tx_started = 0; + } else { + unsigned long ready_mask; + ready_mask = irq_mask1_rd & (IO_MASK(R_IRQ_MASK1_RD, ser0_ready) | + IO_MASK(R_IRQ_MASK1_RD, ser1_ready) | + IO_MASK(R_IRQ_MASK1_RD, ser2_ready) | + IO_MASK(R_IRQ_MASK1_RD, ser3_ready)); + if (ready_mask) { + reentered_ready_mask |= ready_mask; + /* Disable those we are about to handle */ + *R_IRQ_MASK1_CLR = ready_mask; + DFLOW(DEBUG_LOG(SERIAL_DEBUG_LINE, "ser_int reentered with TX %X\n", ready_mask)); + } + } + + local_irq_restore(flags); + return IRQ_RETVAL(handled); +} /* ser_interrupt */ +#endif + +/* + * ------------------------------------------------------------------- + * Here ends the serial interrupt routines. + * ------------------------------------------------------------------- + */ + +/* + * This routine is used to handle the "bottom half" processing for the + * serial driver, known also the "software interrupt" processing. + * This processing is done at the kernel interrupt level, after the + * rs_interrupt() has returned, BUT WITH INTERRUPTS TURNED ON. This + * is where time-consuming activities which can not be done in the + * interrupt driver proper are done; the interrupt driver schedules + * them using rs_sched_event(), and they get done here. + */ +static void +do_softint(struct work_struct *work) +{ + struct e100_serial *info; + struct tty_struct *tty; + + info = container_of(work, struct e100_serial, work); + + tty = info->port.tty; + if (!tty) + return; + + if (test_and_clear_bit(RS_EVENT_WRITE_WAKEUP, &info->event)) + tty_wakeup(tty); +} + +static int +startup(struct e100_serial * info) +{ + unsigned long flags; + unsigned long xmit_page; + int i; + + xmit_page = get_zeroed_page(GFP_KERNEL); + if (!xmit_page) + return -ENOMEM; + + local_irq_save(flags); + + /* if it was already initialized, skip this */ + + if (info->port.flags & ASYNC_INITIALIZED) { + local_irq_restore(flags); + free_page(xmit_page); + return 0; + } + + if (info->xmit.buf) + free_page(xmit_page); + else + info->xmit.buf = (unsigned char *) xmit_page; + +#ifdef SERIAL_DEBUG_OPEN + printk("starting up ttyS%d (xmit_buf 0x%p)...\n", info->line, info->xmit.buf); +#endif + + /* + * Clear the FIFO buffers and disable them + * (they will be reenabled in change_speed()) + */ + + /* + * Reset the DMA channels and make sure their interrupts are cleared + */ + + if (info->dma_in_enabled) { + info->uses_dma_in = 1; + e100_enable_rxdma_channel(info); + + *info->icmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, reset); + + /* Wait until reset cycle is complete */ + while (IO_EXTRACT(R_DMA_CH6_CMD, cmd, *info->icmdadr) == + IO_STATE_VALUE(R_DMA_CH6_CMD, cmd, reset)); + + /* Make sure the irqs are cleared */ + *info->iclrintradr = + IO_STATE(R_DMA_CH6_CLR_INTR, clr_descr, do) | + IO_STATE(R_DMA_CH6_CLR_INTR, clr_eop, do); + } else { + e100_disable_rxdma_channel(info); + } + + if (info->dma_out_enabled) { + info->uses_dma_out = 1; + e100_enable_txdma_channel(info); + *info->ocmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, reset); + + while (IO_EXTRACT(R_DMA_CH6_CMD, cmd, *info->ocmdadr) == + IO_STATE_VALUE(R_DMA_CH6_CMD, cmd, reset)); + + /* Make sure the irqs are cleared */ + *info->oclrintradr = + IO_STATE(R_DMA_CH6_CLR_INTR, clr_descr, do) | + IO_STATE(R_DMA_CH6_CLR_INTR, clr_eop, do); + } else { + e100_disable_txdma_channel(info); + } + + if (info->port.tty) + clear_bit(TTY_IO_ERROR, &info->port.tty->flags); + + info->xmit.head = info->xmit.tail = 0; + info->first_recv_buffer = info->last_recv_buffer = NULL; + info->recv_cnt = info->max_recv_cnt = 0; + + for (i = 0; i < SERIAL_RECV_DESCRIPTORS; i++) + info->rec_descr[i].buf = 0; + + /* + * and set the speed and other flags of the serial port + * this will start the rx/tx as well + */ +#ifdef SERIAL_HANDLE_EARLY_ERRORS + e100_enable_serial_data_irq(info); +#endif + change_speed(info); + + /* dummy read to reset any serial errors */ + + (void)info->ioport[REG_DATA]; + + /* enable the interrupts */ + if (info->uses_dma_out) + e100_enable_txdma_irq(info); + + e100_enable_rx_irq(info); + + info->tr_running = 0; /* to be sure we don't lock up the transmitter */ + + /* setup the dma input descriptor and start dma */ + + start_receive(info); + + /* for safety, make sure the descriptors last result is 0 bytes written */ + + info->tr_descr.sw_len = 0; + info->tr_descr.hw_len = 0; + info->tr_descr.status = 0; + + /* enable RTS/DTR last */ + + e100_rts(info, 1); + e100_dtr(info, 1); + + info->port.flags |= ASYNC_INITIALIZED; + + local_irq_restore(flags); + return 0; +} + +/* + * This routine will shutdown a serial port; interrupts are disabled, and + * DTR is dropped if the hangup on close termio flag is on. + */ +static void +shutdown(struct e100_serial * info) +{ + unsigned long flags; + struct etrax_dma_descr *descr = info->rec_descr; + struct etrax_recv_buffer *buffer; + int i; + + /* shut down the transmitter and receiver */ + DFLOW(DEBUG_LOG(info->line, "shutdown %i\n", info->line)); + e100_disable_rx(info); + info->ioport[REG_TR_CTRL] = (info->tx_ctrl &= ~0x40); + + /* disable interrupts, reset dma channels */ + if (info->uses_dma_in) { + e100_disable_rxdma_irq(info); + *info->icmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, reset); + info->uses_dma_in = 0; + } else { + e100_disable_serial_data_irq(info); + } + + if (info->uses_dma_out) { + e100_disable_txdma_irq(info); + info->tr_running = 0; + *info->ocmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, reset); + info->uses_dma_out = 0; + } else { + e100_disable_serial_tx_ready_irq(info); + info->tr_running = 0; + } + + if (!(info->port.flags & ASYNC_INITIALIZED)) + return; + +#ifdef SERIAL_DEBUG_OPEN + printk("Shutting down serial port %d (irq %d)....\n", info->line, + info->irq); +#endif + + local_irq_save(flags); + + if (info->xmit.buf) { + free_page((unsigned long)info->xmit.buf); + info->xmit.buf = NULL; + } + + for (i = 0; i < SERIAL_RECV_DESCRIPTORS; i++) + if (descr[i].buf) { + buffer = phys_to_virt(descr[i].buf) - sizeof *buffer; + kfree(buffer); + descr[i].buf = 0; + } + + if (!info->port.tty || (info->port.tty->termios.c_cflag & HUPCL)) { + /* hang up DTR and RTS if HUPCL is enabled */ + e100_dtr(info, 0); + e100_rts(info, 0); /* could check CRTSCTS before doing this */ + } + + if (info->port.tty) + set_bit(TTY_IO_ERROR, &info->port.tty->flags); + + info->port.flags &= ~ASYNC_INITIALIZED; + local_irq_restore(flags); +} + + +/* change baud rate and other assorted parameters */ + +static void +change_speed(struct e100_serial *info) +{ + unsigned int cflag; + unsigned long xoff; + unsigned long flags; + /* first some safety checks */ + + if (!info->port.tty) + return; + if (!info->ioport) + return; + + cflag = info->port.tty->termios.c_cflag; + + /* possibly, the tx/rx should be disabled first to do this safely */ + + /* change baud-rate and write it to the hardware */ + if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST) { + /* Special baudrate */ + u32 mask = 0xFF << (info->line*8); /* Each port has 8 bits */ + unsigned long alt_source = + IO_STATE(R_ALT_SER_BAUDRATE, ser0_rec, normal) | + IO_STATE(R_ALT_SER_BAUDRATE, ser0_tr, normal); + /* R_ALT_SER_BAUDRATE selects the source */ + DBAUD(printk("Custom baudrate: baud_base/divisor %lu/%i\n", + (unsigned long)info->baud_base, info->custom_divisor)); + if (info->baud_base == SERIAL_PRESCALE_BASE) { + /* 0, 2-65535 (0=65536) */ + u16 divisor = info->custom_divisor; + /* R_SERIAL_PRESCALE (upper 16 bits of R_CLOCK_PRESCALE) */ + /* baudrate is 3.125MHz/custom_divisor */ + alt_source = + IO_STATE(R_ALT_SER_BAUDRATE, ser0_rec, prescale) | + IO_STATE(R_ALT_SER_BAUDRATE, ser0_tr, prescale); + alt_source = 0x11; + DBAUD(printk("Writing SERIAL_PRESCALE: divisor %i\n", divisor)); + *R_SERIAL_PRESCALE = divisor; + info->baud = SERIAL_PRESCALE_BASE/divisor; + } +#ifdef CONFIG_ETRAX_EXTERN_PB6CLK_ENABLED + else if ((info->baud_base==CONFIG_ETRAX_EXTERN_PB6CLK_FREQ/8 && + info->custom_divisor == 1) || + (info->baud_base==CONFIG_ETRAX_EXTERN_PB6CLK_FREQ && + info->custom_divisor == 8)) { + /* ext_clk selected */ + alt_source = + IO_STATE(R_ALT_SER_BAUDRATE, ser0_rec, extern) | + IO_STATE(R_ALT_SER_BAUDRATE, ser0_tr, extern); + DBAUD(printk("using external baudrate: %lu\n", CONFIG_ETRAX_EXTERN_PB6CLK_FREQ/8)); + info->baud = CONFIG_ETRAX_EXTERN_PB6CLK_FREQ/8; + } +#endif + else + { + /* Bad baudbase, we don't support using timer0 + * for baudrate. + */ + printk(KERN_WARNING "Bad baud_base/custom_divisor: %lu/%i\n", + (unsigned long)info->baud_base, info->custom_divisor); + } + r_alt_ser_baudrate_shadow &= ~mask; + r_alt_ser_baudrate_shadow |= (alt_source << (info->line*8)); + *R_ALT_SER_BAUDRATE = r_alt_ser_baudrate_shadow; + } else { + /* Normal baudrate */ + /* Make sure we use normal baudrate */ + u32 mask = 0xFF << (info->line*8); /* Each port has 8 bits */ + unsigned long alt_source = + IO_STATE(R_ALT_SER_BAUDRATE, ser0_rec, normal) | + IO_STATE(R_ALT_SER_BAUDRATE, ser0_tr, normal); + r_alt_ser_baudrate_shadow &= ~mask; + r_alt_ser_baudrate_shadow |= (alt_source << (info->line*8)); + *R_ALT_SER_BAUDRATE = r_alt_ser_baudrate_shadow; + + info->baud = cflag_to_baud(cflag); + info->ioport[REG_BAUD] = cflag_to_etrax_baud(cflag); + } + + /* start with default settings and then fill in changes */ + local_irq_save(flags); + /* 8 bit, no/even parity */ + info->rx_ctrl &= ~(IO_MASK(R_SERIAL0_REC_CTRL, rec_bitnr) | + IO_MASK(R_SERIAL0_REC_CTRL, rec_par_en) | + IO_MASK(R_SERIAL0_REC_CTRL, rec_par)); + + /* 8 bit, no/even parity, 1 stop bit, no cts */ + info->tx_ctrl &= ~(IO_MASK(R_SERIAL0_TR_CTRL, tr_bitnr) | + IO_MASK(R_SERIAL0_TR_CTRL, tr_par_en) | + IO_MASK(R_SERIAL0_TR_CTRL, tr_par) | + IO_MASK(R_SERIAL0_TR_CTRL, stop_bits) | + IO_MASK(R_SERIAL0_TR_CTRL, auto_cts)); + + if ((cflag & CSIZE) == CS7) { + /* set 7 bit mode */ + info->tx_ctrl |= IO_STATE(R_SERIAL0_TR_CTRL, tr_bitnr, tr_7bit); + info->rx_ctrl |= IO_STATE(R_SERIAL0_REC_CTRL, rec_bitnr, rec_7bit); + } + + if (cflag & CSTOPB) { + /* set 2 stop bit mode */ + info->tx_ctrl |= IO_STATE(R_SERIAL0_TR_CTRL, stop_bits, two_bits); + } + + if (cflag & PARENB) { + /* enable parity */ + info->tx_ctrl |= IO_STATE(R_SERIAL0_TR_CTRL, tr_par_en, enable); + info->rx_ctrl |= IO_STATE(R_SERIAL0_REC_CTRL, rec_par_en, enable); + } + + if (cflag & CMSPAR) { + /* enable stick parity, PARODD mean Mark which matches ETRAX */ + info->tx_ctrl |= IO_STATE(R_SERIAL0_TR_CTRL, tr_stick_par, stick); + info->rx_ctrl |= IO_STATE(R_SERIAL0_REC_CTRL, rec_stick_par, stick); + } + if (cflag & PARODD) { + /* set odd parity (or Mark if CMSPAR) */ + info->tx_ctrl |= IO_STATE(R_SERIAL0_TR_CTRL, tr_par, odd); + info->rx_ctrl |= IO_STATE(R_SERIAL0_REC_CTRL, rec_par, odd); + } + + if (cflag & CRTSCTS) { + /* enable automatic CTS handling */ + DFLOW(DEBUG_LOG(info->line, "FLOW auto_cts enabled\n", 0)); + info->tx_ctrl |= IO_STATE(R_SERIAL0_TR_CTRL, auto_cts, active); + } + + /* make sure the tx and rx are enabled */ + + info->tx_ctrl |= IO_STATE(R_SERIAL0_TR_CTRL, tr_enable, enable); + info->rx_ctrl |= IO_STATE(R_SERIAL0_REC_CTRL, rec_enable, enable); + + /* actually write the control regs to the hardware */ + + info->ioport[REG_TR_CTRL] = info->tx_ctrl; + info->ioport[REG_REC_CTRL] = info->rx_ctrl; + xoff = IO_FIELD(R_SERIAL0_XOFF, xoff_char, STOP_CHAR(info->port.tty)); + xoff |= IO_STATE(R_SERIAL0_XOFF, tx_stop, enable); + if (info->port.tty->termios.c_iflag & IXON ) { + DFLOW(DEBUG_LOG(info->line, "FLOW XOFF enabled 0x%02X\n", + STOP_CHAR(info->port.tty))); + xoff |= IO_STATE(R_SERIAL0_XOFF, auto_xoff, enable); + } + + *((unsigned long *)&info->ioport[REG_XOFF]) = xoff; + local_irq_restore(flags); + + update_char_time(info); + +} /* change_speed */ + +/* start transmitting chars NOW */ + +static void +rs_flush_chars(struct tty_struct *tty) +{ + struct e100_serial *info = (struct e100_serial *)tty->driver_data; + unsigned long flags; + + if (info->tr_running || + info->xmit.head == info->xmit.tail || + tty->stopped || + !info->xmit.buf) + return; + +#ifdef SERIAL_DEBUG_FLOW + printk("rs_flush_chars\n"); +#endif + + /* this protection might not exactly be necessary here */ + + local_irq_save(flags); + start_transmit(info); + local_irq_restore(flags); +} + +static int rs_raw_write(struct tty_struct *tty, + const unsigned char *buf, int count) +{ + int c, ret = 0; + struct e100_serial *info = (struct e100_serial *)tty->driver_data; + unsigned long flags; + + /* first some sanity checks */ + + if (!info->xmit.buf) + return 0; + +#ifdef SERIAL_DEBUG_DATA + if (info->line == SERIAL_DEBUG_LINE) + printk("rs_raw_write (%d), status %d\n", + count, info->ioport[REG_STATUS]); +#endif + + local_save_flags(flags); + DFLOW(DEBUG_LOG(info->line, "write count %i ", count)); + DFLOW(DEBUG_LOG(info->line, "ldisc %i\n", tty->ldisc.chars_in_buffer(tty))); + + + /* The local_irq_disable/restore_flags pairs below are needed + * because the DMA interrupt handler moves the info->xmit values. + * the memcpy needs to be in the critical region unfortunately, + * because we need to read xmit values, memcpy, write xmit values + * in one atomic operation... this could perhaps be avoided by + * more clever design. + */ + local_irq_disable(); + while (count) { + c = CIRC_SPACE_TO_END(info->xmit.head, + info->xmit.tail, + SERIAL_XMIT_SIZE); + + if (count < c) + c = count; + if (c <= 0) + break; + + memcpy(info->xmit.buf + info->xmit.head, buf, c); + info->xmit.head = (info->xmit.head + c) & + (SERIAL_XMIT_SIZE-1); + buf += c; + count -= c; + ret += c; + } + local_irq_restore(flags); + + /* enable transmitter if not running, unless the tty is stopped + * this does not need IRQ protection since if tr_running == 0 + * the IRQ's are not running anyway for this port. + */ + DFLOW(DEBUG_LOG(info->line, "write ret %i\n", ret)); + + if (info->xmit.head != info->xmit.tail && + !tty->stopped && + !info->tr_running) { + start_transmit(info); + } + + return ret; +} /* raw_raw_write() */ + +static int +rs_write(struct tty_struct *tty, + const unsigned char *buf, int count) +{ +#if defined(CONFIG_ETRAX_RS485) + struct e100_serial *info = (struct e100_serial *)tty->driver_data; + + if (info->rs485.flags & SER_RS485_ENABLED) + { + /* If we are in RS-485 mode, we need to toggle RTS and disable + * the receiver before initiating a DMA transfer + */ +#ifdef CONFIG_ETRAX_FAST_TIMER + /* Abort any started timer */ + fast_timers_rs485[info->line].function = NULL; + del_fast_timer(&fast_timers_rs485[info->line]); +#endif + e100_rts(info, (info->rs485.flags & SER_RS485_RTS_ON_SEND)); +#if defined(CONFIG_ETRAX_RS485_DISABLE_RECEIVER) + e100_disable_rx(info); + e100_enable_rx_irq(info); +#endif + if (info->rs485.delay_rts_before_send > 0) + msleep(info->rs485.delay_rts_before_send); + } +#endif /* CONFIG_ETRAX_RS485 */ + + count = rs_raw_write(tty, buf, count); + +#if defined(CONFIG_ETRAX_RS485) + if (info->rs485.flags & SER_RS485_ENABLED) + { + unsigned int val; + /* If we are in RS-485 mode the following has to be done: + * wait until DMA is ready + * wait on transmit shift register + * toggle RTS + * enable the receiver + */ + + /* Sleep until all sent */ + tty_wait_until_sent(tty, 0); +#ifdef CONFIG_ETRAX_FAST_TIMER + /* Now sleep a little more so that shift register is empty */ + schedule_usleep(info->char_time_usec * 2); +#endif + /* wait on transmit shift register */ + do{ + get_lsr_info(info, &val); + }while (!(val & TIOCSER_TEMT)); + + e100_rts(info, (info->rs485.flags & SER_RS485_RTS_AFTER_SEND)); + +#if defined(CONFIG_ETRAX_RS485_DISABLE_RECEIVER) + e100_enable_rx(info); + e100_enable_rxdma_irq(info); +#endif + } +#endif /* CONFIG_ETRAX_RS485 */ + + return count; +} /* rs_write */ + + +/* how much space is available in the xmit buffer? */ + +static int +rs_write_room(struct tty_struct *tty) +{ + struct e100_serial *info = (struct e100_serial *)tty->driver_data; + + return CIRC_SPACE(info->xmit.head, info->xmit.tail, SERIAL_XMIT_SIZE); +} + +/* How many chars are in the xmit buffer? + * This does not include any chars in the transmitter FIFO. + * Use wait_until_sent for waiting for FIFO drain. + */ + +static int +rs_chars_in_buffer(struct tty_struct *tty) +{ + struct e100_serial *info = (struct e100_serial *)tty->driver_data; + + return CIRC_CNT(info->xmit.head, info->xmit.tail, SERIAL_XMIT_SIZE); +} + +/* discard everything in the xmit buffer */ + +static void +rs_flush_buffer(struct tty_struct *tty) +{ + struct e100_serial *info = (struct e100_serial *)tty->driver_data; + unsigned long flags; + + local_irq_save(flags); + info->xmit.head = info->xmit.tail = 0; + local_irq_restore(flags); + + tty_wakeup(tty); +} + +/* + * This function is used to send a high-priority XON/XOFF character to + * the device + * + * Since we use DMA we don't check for info->x_char in transmit_chars_dma(), + * but we do it in handle_ser_tx_interrupt(). + * We disable DMA channel and enable tx ready interrupt and write the + * character when possible. + */ +static void rs_send_xchar(struct tty_struct *tty, char ch) +{ + struct e100_serial *info = (struct e100_serial *)tty->driver_data; + unsigned long flags; + local_irq_save(flags); + if (info->uses_dma_out) { + /* Put the DMA on hold and disable the channel */ + *info->ocmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, hold); + while (IO_EXTRACT(R_DMA_CH6_CMD, cmd, *info->ocmdadr) != + IO_STATE_VALUE(R_DMA_CH6_CMD, cmd, hold)); + e100_disable_txdma_channel(info); + } + + /* Must make sure transmitter is not stopped before we can transmit */ + if (tty->stopped) + rs_start(tty); + + /* Enable manual transmit interrupt and send from there */ + DFLOW(DEBUG_LOG(info->line, "rs_send_xchar 0x%02X\n", ch)); + info->x_char = ch; + e100_enable_serial_tx_ready_irq(info); + local_irq_restore(flags); +} + +/* + * ------------------------------------------------------------ + * rs_throttle() + * + * This routine is called by the upper-layer tty layer to signal that + * incoming characters should be throttled. + * ------------------------------------------------------------ + */ +static void +rs_throttle(struct tty_struct * tty) +{ + struct e100_serial *info = (struct e100_serial *)tty->driver_data; +#ifdef SERIAL_DEBUG_THROTTLE + char buf[64]; + + printk("throttle %s: %lu....\n", tty_name(tty, buf), + (unsigned long)tty->ldisc.chars_in_buffer(tty)); +#endif + DFLOW(DEBUG_LOG(info->line,"rs_throttle %lu\n", tty->ldisc.chars_in_buffer(tty))); + + /* Do RTS before XOFF since XOFF might take some time */ + if (tty->termios.c_cflag & CRTSCTS) { + /* Turn off RTS line */ + e100_rts(info, 0); + } + if (I_IXOFF(tty)) + rs_send_xchar(tty, STOP_CHAR(tty)); + +} + +static void +rs_unthrottle(struct tty_struct * tty) +{ + struct e100_serial *info = (struct e100_serial *)tty->driver_data; +#ifdef SERIAL_DEBUG_THROTTLE + char buf[64]; + + printk("unthrottle %s: %lu....\n", tty_name(tty, buf), + (unsigned long)tty->ldisc.chars_in_buffer(tty)); +#endif + DFLOW(DEBUG_LOG(info->line,"rs_unthrottle ldisc %d\n", tty->ldisc.chars_in_buffer(tty))); + DFLOW(DEBUG_LOG(info->line,"rs_unthrottle flip.count: %i\n", tty->flip.count)); + /* Do RTS before XOFF since XOFF might take some time */ + if (tty->termios.c_cflag & CRTSCTS) { + /* Assert RTS line */ + e100_rts(info, 1); + } + + if (I_IXOFF(tty)) { + if (info->x_char) + info->x_char = 0; + else + rs_send_xchar(tty, START_CHAR(tty)); + } + +} + +/* + * ------------------------------------------------------------ + * rs_ioctl() and friends + * ------------------------------------------------------------ + */ + +static int +get_serial_info(struct e100_serial * info, + struct serial_struct * retinfo) +{ + struct serial_struct tmp; + + /* this is all probably wrong, there are a lot of fields + * here that we don't have in e100_serial and maybe we + * should set them to something else than 0. + */ + + if (!retinfo) + return -EFAULT; + memset(&tmp, 0, sizeof(tmp)); + tmp.type = info->type; + tmp.line = info->line; + tmp.port = (int)info->ioport; + tmp.irq = info->irq; + tmp.flags = info->port.flags; + tmp.baud_base = info->baud_base; + tmp.close_delay = info->port.close_delay; + tmp.closing_wait = info->port.closing_wait; + tmp.custom_divisor = info->custom_divisor; + if (copy_to_user(retinfo, &tmp, sizeof(*retinfo))) + return -EFAULT; + return 0; +} + +static int +set_serial_info(struct e100_serial *info, + struct serial_struct *new_info) +{ + struct serial_struct new_serial; + struct e100_serial old_info; + int retval = 0; + + if (copy_from_user(&new_serial, new_info, sizeof(new_serial))) + return -EFAULT; + + old_info = *info; + + if (!capable(CAP_SYS_ADMIN)) { + if ((new_serial.type != info->type) || + (new_serial.close_delay != info->port.close_delay) || + ((new_serial.flags & ~ASYNC_USR_MASK) != + (info->port.flags & ~ASYNC_USR_MASK))) + return -EPERM; + info->port.flags = ((info->port.flags & ~ASYNC_USR_MASK) | + (new_serial.flags & ASYNC_USR_MASK)); + goto check_and_exit; + } + + if (info->port.count > 1) + return -EBUSY; + + /* + * OK, past this point, all the error checking has been done. + * At this point, we start making changes..... + */ + + info->baud_base = new_serial.baud_base; + info->port.flags = ((info->port.flags & ~ASYNC_FLAGS) | + (new_serial.flags & ASYNC_FLAGS)); + info->custom_divisor = new_serial.custom_divisor; + info->type = new_serial.type; + info->port.close_delay = new_serial.close_delay; + info->port.closing_wait = new_serial.closing_wait; + info->port.low_latency = (info->port.flags & ASYNC_LOW_LATENCY) ? 1 : 0; + + check_and_exit: + if (info->port.flags & ASYNC_INITIALIZED) { + change_speed(info); + } else + retval = startup(info); + return retval; +} + +/* + * get_lsr_info - get line status register info + * + * Purpose: Let user call ioctl() to get info when the UART physically + * is emptied. On bus types like RS485, the transmitter must + * release the bus after transmitting. This must be done when + * the transmit shift register is empty, not be done when the + * transmit holding register is empty. This functionality + * allows an RS485 driver to be written in user space. + */ +static int +get_lsr_info(struct e100_serial * info, unsigned int *value) +{ + unsigned int result = TIOCSER_TEMT; + unsigned long curr_time = jiffies; + unsigned long curr_time_usec = GET_JIFFIES_USEC(); + unsigned long elapsed_usec = + (curr_time - info->last_tx_active) * 1000000/HZ + + curr_time_usec - info->last_tx_active_usec; + + if (info->xmit.head != info->xmit.tail || + elapsed_usec < 2*info->char_time_usec) { + result = 0; + } + + if (copy_to_user(value, &result, sizeof(int))) + return -EFAULT; + return 0; +} + +#ifdef SERIAL_DEBUG_IO +struct state_str +{ + int state; + const char *str; +}; + +const struct state_str control_state_str[] = { + {TIOCM_DTR, "DTR" }, + {TIOCM_RTS, "RTS"}, + {TIOCM_ST, "ST?" }, + {TIOCM_SR, "SR?" }, + {TIOCM_CTS, "CTS" }, + {TIOCM_CD, "CD" }, + {TIOCM_RI, "RI" }, + {TIOCM_DSR, "DSR" }, + {0, NULL } +}; + +char *get_control_state_str(int MLines, char *s) +{ + int i = 0; + + s[0]='\0'; + while (control_state_str[i].str != NULL) { + if (MLines & control_state_str[i].state) { + if (s[0] != '\0') { + strcat(s, ", "); + } + strcat(s, control_state_str[i].str); + } + i++; + } + return s; +} +#endif + +static int +rs_break(struct tty_struct *tty, int break_state) +{ + struct e100_serial *info = (struct e100_serial *)tty->driver_data; + unsigned long flags; + + if (!info->ioport) + return -EIO; + + local_irq_save(flags); + if (break_state == -1) { + /* Go to manual mode and set the txd pin to 0 */ + /* Clear bit 7 (txd) and 6 (tr_enable) */ + info->tx_ctrl &= 0x3F; + } else { + /* Set bit 7 (txd) and 6 (tr_enable) */ + info->tx_ctrl |= (0x80 | 0x40); + } + info->ioport[REG_TR_CTRL] = info->tx_ctrl; + local_irq_restore(flags); + return 0; +} + +static int +rs_tiocmset(struct tty_struct *tty, unsigned int set, unsigned int clear) +{ + struct e100_serial *info = (struct e100_serial *)tty->driver_data; + unsigned long flags; + + local_irq_save(flags); + + if (clear & TIOCM_RTS) + e100_rts(info, 0); + if (clear & TIOCM_DTR) + e100_dtr(info, 0); + /* Handle FEMALE behaviour */ + if (clear & TIOCM_RI) + e100_ri_out(info, 0); + if (clear & TIOCM_CD) + e100_cd_out(info, 0); + + if (set & TIOCM_RTS) + e100_rts(info, 1); + if (set & TIOCM_DTR) + e100_dtr(info, 1); + /* Handle FEMALE behaviour */ + if (set & TIOCM_RI) + e100_ri_out(info, 1); + if (set & TIOCM_CD) + e100_cd_out(info, 1); + + local_irq_restore(flags); + return 0; +} + +static int +rs_tiocmget(struct tty_struct *tty) +{ + struct e100_serial *info = (struct e100_serial *)tty->driver_data; + unsigned int result; + unsigned long flags; + + local_irq_save(flags); + + result = + (!E100_RTS_GET(info) ? TIOCM_RTS : 0) + | (!E100_DTR_GET(info) ? TIOCM_DTR : 0) + | (!E100_RI_GET(info) ? TIOCM_RNG : 0) + | (!E100_DSR_GET(info) ? TIOCM_DSR : 0) + | (!E100_CD_GET(info) ? TIOCM_CAR : 0) + | (!E100_CTS_GET(info) ? TIOCM_CTS : 0); + + local_irq_restore(flags); + +#ifdef SERIAL_DEBUG_IO + printk(KERN_DEBUG "ser%i: modem state: %i 0x%08X\n", + info->line, result, result); + { + char s[100]; + + get_control_state_str(result, s); + printk(KERN_DEBUG "state: %s\n", s); + } +#endif + return result; + +} + + +static int +rs_ioctl(struct tty_struct *tty, + unsigned int cmd, unsigned long arg) +{ + struct e100_serial * info = (struct e100_serial *)tty->driver_data; + + if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) && + (cmd != TIOCSERCONFIG) && (cmd != TIOCSERGWILD) && + (cmd != TIOCSERSWILD) && (cmd != TIOCSERGSTRUCT)) { + if (tty->flags & (1 << TTY_IO_ERROR)) + return -EIO; + } + + switch (cmd) { + case TIOCGSERIAL: + return get_serial_info(info, + (struct serial_struct *) arg); + case TIOCSSERIAL: + return set_serial_info(info, + (struct serial_struct *) arg); + case TIOCSERGETLSR: /* Get line status register */ + return get_lsr_info(info, (unsigned int *) arg); + + case TIOCSERGSTRUCT: + if (copy_to_user((struct e100_serial *) arg, + info, sizeof(struct e100_serial))) + return -EFAULT; + return 0; + +#if defined(CONFIG_ETRAX_RS485) + case TIOCSERSETRS485: + { + /* In this ioctl we still use the old structure + * rs485_control for backward compatibility + * (if we use serial_rs485, then old user-level code + * wouldn't work anymore...). + * The use of this ioctl is deprecated: use TIOCSRS485 + * instead.*/ + struct rs485_control rs485ctrl; + struct serial_rs485 rs485data; + printk(KERN_DEBUG "The use of this ioctl is deprecated. Use TIOCSRS485 instead\n"); + if (copy_from_user(&rs485ctrl, (struct rs485_control *)arg, + sizeof(rs485ctrl))) + return -EFAULT; + + rs485data.delay_rts_before_send = rs485ctrl.delay_rts_before_send; + rs485data.flags = 0; + + if (rs485ctrl.enabled) + rs485data.flags |= SER_RS485_ENABLED; + else + rs485data.flags &= ~(SER_RS485_ENABLED); + + if (rs485ctrl.rts_on_send) + rs485data.flags |= SER_RS485_RTS_ON_SEND; + else + rs485data.flags &= ~(SER_RS485_RTS_ON_SEND); + + if (rs485ctrl.rts_after_sent) + rs485data.flags |= SER_RS485_RTS_AFTER_SEND; + else + rs485data.flags &= ~(SER_RS485_RTS_AFTER_SEND); + + return e100_enable_rs485(tty, &rs485data); + } + + case TIOCSRS485: + { + /* This is the new version of TIOCSRS485, with new + * data structure serial_rs485 */ + struct serial_rs485 rs485data; + if (copy_from_user(&rs485data, (struct rs485_control *)arg, + sizeof(rs485data))) + return -EFAULT; + + return e100_enable_rs485(tty, &rs485data); + } + + case TIOCGRS485: + { + struct serial_rs485 *rs485data = + &(((struct e100_serial *)tty->driver_data)->rs485); + /* This is the ioctl to get RS485 data from user-space */ + if (copy_to_user((struct serial_rs485 *) arg, + rs485data, + sizeof(struct serial_rs485))) + return -EFAULT; + break; + } + + case TIOCSERWRRS485: + { + struct rs485_write rs485wr; + if (copy_from_user(&rs485wr, (struct rs485_write *)arg, + sizeof(rs485wr))) + return -EFAULT; + + return e100_write_rs485(tty, rs485wr.outc, rs485wr.outc_size); + } +#endif + + default: + return -ENOIOCTLCMD; + } + return 0; +} + +static void +rs_set_termios(struct tty_struct *tty, struct ktermios *old_termios) +{ + struct e100_serial *info = (struct e100_serial *)tty->driver_data; + + change_speed(info); + + /* Handle turning off CRTSCTS */ + if ((old_termios->c_cflag & CRTSCTS) && + !(tty->termios.c_cflag & CRTSCTS)) + rs_start(tty); + +} + +/* + * ------------------------------------------------------------ + * rs_close() + * + * This routine is called when the serial port gets closed. First, we + * wait for the last remaining data to be sent. Then, we unlink its + * S structure from the interrupt chain if necessary, and we free + * that IRQ if nothing is left in the chain. + * ------------------------------------------------------------ + */ +static void +rs_close(struct tty_struct *tty, struct file * filp) +{ + struct e100_serial * info = (struct e100_serial *)tty->driver_data; + unsigned long flags; + + if (!info) + return; + + /* interrupts are disabled for this entire function */ + + local_irq_save(flags); + + if (tty_hung_up_p(filp)) { + local_irq_restore(flags); + return; + } + +#ifdef SERIAL_DEBUG_OPEN + printk("[%d] rs_close ttyS%d, count = %d\n", current->pid, + info->line, info->count); +#endif + if ((tty->count == 1) && (info->port.count != 1)) { + /* + * Uh, oh. tty->count is 1, which means that the tty + * structure will be freed. Info->count should always + * be one in these conditions. If it's greater than + * one, we've got real problems, since it means the + * serial port won't be shutdown. + */ + printk(KERN_ERR + "rs_close: bad serial port count; tty->count is 1, " + "info->count is %d\n", info->port.count); + info->port.count = 1; + } + if (--info->port.count < 0) { + printk(KERN_ERR "rs_close: bad serial port count for ttyS%d: %d\n", + info->line, info->port.count); + info->port.count = 0; + } + if (info->port.count) { + local_irq_restore(flags); + return; + } + info->port.flags |= ASYNC_CLOSING; + /* + * Save the termios structure, since this port may have + * separate termios for callout and dialin. + */ + if (info->port.flags & ASYNC_NORMAL_ACTIVE) + info->normal_termios = tty->termios; + /* + * Now we wait for the transmit buffer to clear; and we notify + * the line discipline to only process XON/XOFF characters. + */ + tty->closing = 1; + if (info->port.closing_wait != ASYNC_CLOSING_WAIT_NONE) + tty_wait_until_sent(tty, info->port.closing_wait); + /* + * At this point we stop accepting input. To do this, we + * disable the serial receiver and the DMA receive interrupt. + */ +#ifdef SERIAL_HANDLE_EARLY_ERRORS + e100_disable_serial_data_irq(info); +#endif + + e100_disable_rx(info); + e100_disable_rx_irq(info); + + if (info->port.flags & ASYNC_INITIALIZED) { + /* + * Before we drop DTR, make sure the UART transmitter + * has completely drained; this is especially + * important as we have a transmit FIFO! + */ + rs_wait_until_sent(tty, HZ); + } + + shutdown(info); + rs_flush_buffer(tty); + tty_ldisc_flush(tty); + tty->closing = 0; + info->event = 0; + info->port.tty = NULL; + if (info->port.blocked_open) { + if (info->port.close_delay) + schedule_timeout_interruptible(info->port.close_delay); + wake_up_interruptible(&info->port.open_wait); + } + info->port.flags &= ~(ASYNC_NORMAL_ACTIVE|ASYNC_CLOSING); + wake_up_interruptible(&info->port.close_wait); + local_irq_restore(flags); + + /* port closed */ + +#if defined(CONFIG_ETRAX_RS485) + if (info->rs485.flags & SER_RS485_ENABLED) { + info->rs485.flags &= ~(SER_RS485_ENABLED); +#if defined(CONFIG_ETRAX_RS485_ON_PA) + *R_PORT_PA_DATA = port_pa_data_shadow &= ~(1 << rs485_pa_bit); +#endif +#if defined(CONFIG_ETRAX_RS485_ON_PORT_G) + REG_SHADOW_SET(R_PORT_G_DATA, port_g_data_shadow, + rs485_port_g_bit, 0); +#endif +#if defined(CONFIG_ETRAX_RS485_LTC1387) + REG_SHADOW_SET(R_PORT_G_DATA, port_g_data_shadow, + CONFIG_ETRAX_RS485_LTC1387_DXEN_PORT_G_BIT, 0); + REG_SHADOW_SET(R_PORT_G_DATA, port_g_data_shadow, + CONFIG_ETRAX_RS485_LTC1387_RXEN_PORT_G_BIT, 0); +#endif + } +#endif + + /* + * Release any allocated DMA irq's. + */ + if (info->dma_in_enabled) { + free_irq(info->dma_in_irq_nbr, info); + cris_free_dma(info->dma_in_nbr, info->dma_in_irq_description); + info->uses_dma_in = 0; +#ifdef SERIAL_DEBUG_OPEN + printk(KERN_DEBUG "DMA irq '%s' freed\n", + info->dma_in_irq_description); +#endif + } + if (info->dma_out_enabled) { + free_irq(info->dma_out_irq_nbr, info); + cris_free_dma(info->dma_out_nbr, info->dma_out_irq_description); + info->uses_dma_out = 0; +#ifdef SERIAL_DEBUG_OPEN + printk(KERN_DEBUG "DMA irq '%s' freed\n", + info->dma_out_irq_description); +#endif + } +} + +/* + * rs_wait_until_sent() --- wait until the transmitter is empty + */ +static void rs_wait_until_sent(struct tty_struct *tty, int timeout) +{ + unsigned long orig_jiffies; + struct e100_serial *info = (struct e100_serial *)tty->driver_data; + unsigned long curr_time = jiffies; + unsigned long curr_time_usec = GET_JIFFIES_USEC(); + long elapsed_usec = + (curr_time - info->last_tx_active) * (1000000/HZ) + + curr_time_usec - info->last_tx_active_usec; + + /* + * Check R_DMA_CHx_STATUS bit 0-6=number of available bytes in FIFO + * R_DMA_CHx_HWSW bit 31-16=nbr of bytes left in DMA buffer (0=64k) + */ + orig_jiffies = jiffies; + while (info->xmit.head != info->xmit.tail || /* More in send queue */ + (*info->ostatusadr & 0x007f) || /* more in FIFO */ + (elapsed_usec < 2*info->char_time_usec)) { + schedule_timeout_interruptible(1); + if (signal_pending(current)) + break; + if (timeout && time_after(jiffies, orig_jiffies + timeout)) + break; + curr_time = jiffies; + curr_time_usec = GET_JIFFIES_USEC(); + elapsed_usec = + (curr_time - info->last_tx_active) * (1000000/HZ) + + curr_time_usec - info->last_tx_active_usec; + } + set_current_state(TASK_RUNNING); +} + +/* + * rs_hangup() --- called by tty_hangup() when a hangup is signaled. + */ +void +rs_hangup(struct tty_struct *tty) +{ + struct e100_serial * info = (struct e100_serial *)tty->driver_data; + + rs_flush_buffer(tty); + shutdown(info); + info->event = 0; + info->port.count = 0; + info->port.flags &= ~ASYNC_NORMAL_ACTIVE; + info->port.tty = NULL; + wake_up_interruptible(&info->port.open_wait); +} + +/* + * ------------------------------------------------------------ + * rs_open() and friends + * ------------------------------------------------------------ + */ +static int +block_til_ready(struct tty_struct *tty, struct file * filp, + struct e100_serial *info) +{ + DECLARE_WAITQUEUE(wait, current); + unsigned long flags; + int retval; + int do_clocal = 0, extra_count = 0; + + /* + * If the device is in the middle of being closed, then block + * until it's done, and then try again. + */ + if (tty_hung_up_p(filp) || + (info->port.flags & ASYNC_CLOSING)) { + wait_event_interruptible_tty(tty, info->port.close_wait, + !(info->port.flags & ASYNC_CLOSING)); +#ifdef SERIAL_DO_RESTART + if (info->port.flags & ASYNC_HUP_NOTIFY) + return -EAGAIN; + else + return -ERESTARTSYS; +#else + return -EAGAIN; +#endif + } + + /* + * If non-blocking mode is set, or the port is not enabled, + * then make the check up front and then exit. + */ + if ((filp->f_flags & O_NONBLOCK) || + (tty->flags & (1 << TTY_IO_ERROR))) { + info->port.flags |= ASYNC_NORMAL_ACTIVE; + return 0; + } + + if (tty->termios.c_cflag & CLOCAL) { + do_clocal = 1; + } + + /* + * Block waiting for the carrier detect and the line to become + * free (i.e., not in use by the callout). While we are in + * this loop, info->port.count is dropped by one, so that + * rs_close() knows when to free things. We restore it upon + * exit, either normal or abnormal. + */ + retval = 0; + add_wait_queue(&info->port.open_wait, &wait); +#ifdef SERIAL_DEBUG_OPEN + printk("block_til_ready before block: ttyS%d, count = %d\n", + info->line, info->port.count); +#endif + local_irq_save(flags); + if (!tty_hung_up_p(filp)) { + extra_count++; + info->port.count--; + } + local_irq_restore(flags); + info->port.blocked_open++; + while (1) { + local_irq_save(flags); + /* assert RTS and DTR */ + e100_rts(info, 1); + e100_dtr(info, 1); + local_irq_restore(flags); + set_current_state(TASK_INTERRUPTIBLE); + if (tty_hung_up_p(filp) || + !(info->port.flags & ASYNC_INITIALIZED)) { +#ifdef SERIAL_DO_RESTART + if (info->port.flags & ASYNC_HUP_NOTIFY) + retval = -EAGAIN; + else + retval = -ERESTARTSYS; +#else + retval = -EAGAIN; +#endif + break; + } + if (!(info->port.flags & ASYNC_CLOSING) && do_clocal) + /* && (do_clocal || DCD_IS_ASSERTED) */ + break; + if (signal_pending(current)) { + retval = -ERESTARTSYS; + break; + } +#ifdef SERIAL_DEBUG_OPEN + printk("block_til_ready blocking: ttyS%d, count = %d\n", + info->line, info->port.count); +#endif + tty_unlock(tty); + schedule(); + tty_lock(tty); + } + set_current_state(TASK_RUNNING); + remove_wait_queue(&info->port.open_wait, &wait); + if (extra_count) + info->port.count++; + info->port.blocked_open--; +#ifdef SERIAL_DEBUG_OPEN + printk("block_til_ready after blocking: ttyS%d, count = %d\n", + info->line, info->port.count); +#endif + if (retval) + return retval; + info->port.flags |= ASYNC_NORMAL_ACTIVE; + return 0; +} + +static void +deinit_port(struct e100_serial *info) +{ + if (info->dma_out_enabled) { + cris_free_dma(info->dma_out_nbr, info->dma_out_irq_description); + free_irq(info->dma_out_irq_nbr, info); + } + if (info->dma_in_enabled) { + cris_free_dma(info->dma_in_nbr, info->dma_in_irq_description); + free_irq(info->dma_in_irq_nbr, info); + } +} + +/* + * This routine is called whenever a serial port is opened. + * It performs the serial-specific initialization for the tty structure. + */ +static int +rs_open(struct tty_struct *tty, struct file * filp) +{ + struct e100_serial *info; + int retval; + int allocated_resources = 0; + + info = rs_table + tty->index; + if (!info->enabled) + return -ENODEV; + +#ifdef SERIAL_DEBUG_OPEN + printk("[%d] rs_open %s, count = %d\n", current->pid, tty->name, + info->port.count); +#endif + + info->port.count++; + tty->driver_data = info; + info->port.tty = tty; + + info->port.low_latency = !!(info->port.flags & ASYNC_LOW_LATENCY); + + /* + * If the port is in the middle of closing, bail out now + */ + if (tty_hung_up_p(filp) || + (info->port.flags & ASYNC_CLOSING)) { + wait_event_interruptible_tty(tty, info->port.close_wait, + !(info->port.flags & ASYNC_CLOSING)); +#ifdef SERIAL_DO_RESTART + return ((info->port.flags & ASYNC_HUP_NOTIFY) ? + -EAGAIN : -ERESTARTSYS); +#else + return -EAGAIN; +#endif + } + + /* + * If DMA is enabled try to allocate the irq's. + */ + if (info->port.count == 1) { + allocated_resources = 1; + if (info->dma_in_enabled) { + if (request_irq(info->dma_in_irq_nbr, + rec_interrupt, + info->dma_in_irq_flags, + info->dma_in_irq_description, + info)) { + printk(KERN_WARNING "DMA irq '%s' busy; " + "falling back to non-DMA mode\n", + info->dma_in_irq_description); + /* Make sure we never try to use DMA in */ + /* for the port again. */ + info->dma_in_enabled = 0; + } else if (cris_request_dma(info->dma_in_nbr, + info->dma_in_irq_description, + DMA_VERBOSE_ON_ERROR, + info->dma_owner)) { + free_irq(info->dma_in_irq_nbr, info); + printk(KERN_WARNING "DMA '%s' busy; " + "falling back to non-DMA mode\n", + info->dma_in_irq_description); + /* Make sure we never try to use DMA in */ + /* for the port again. */ + info->dma_in_enabled = 0; + } +#ifdef SERIAL_DEBUG_OPEN + else + printk(KERN_DEBUG "DMA irq '%s' allocated\n", + info->dma_in_irq_description); +#endif + } + if (info->dma_out_enabled) { + if (request_irq(info->dma_out_irq_nbr, + tr_interrupt, + info->dma_out_irq_flags, + info->dma_out_irq_description, + info)) { + printk(KERN_WARNING "DMA irq '%s' busy; " + "falling back to non-DMA mode\n", + info->dma_out_irq_description); + /* Make sure we never try to use DMA out */ + /* for the port again. */ + info->dma_out_enabled = 0; + } else if (cris_request_dma(info->dma_out_nbr, + info->dma_out_irq_description, + DMA_VERBOSE_ON_ERROR, + info->dma_owner)) { + free_irq(info->dma_out_irq_nbr, info); + printk(KERN_WARNING "DMA '%s' busy; " + "falling back to non-DMA mode\n", + info->dma_out_irq_description); + /* Make sure we never try to use DMA out */ + /* for the port again. */ + info->dma_out_enabled = 0; + } +#ifdef SERIAL_DEBUG_OPEN + else + printk(KERN_DEBUG "DMA irq '%s' allocated\n", + info->dma_out_irq_description); +#endif + } + } + + /* + * Start up the serial port + */ + + retval = startup(info); + if (retval) { + if (allocated_resources) + deinit_port(info); + + /* FIXME Decrease count info->port.count here too? */ + return retval; + } + + + retval = block_til_ready(tty, filp, info); + if (retval) { +#ifdef SERIAL_DEBUG_OPEN + printk("rs_open returning after block_til_ready with %d\n", + retval); +#endif + if (allocated_resources) + deinit_port(info); + + return retval; + } + + if ((info->port.count == 1) && (info->port.flags & ASYNC_SPLIT_TERMIOS)) { + tty->termios = info->normal_termios; + change_speed(info); + } + +#ifdef SERIAL_DEBUG_OPEN + printk("rs_open ttyS%d successful...\n", info->line); +#endif + DLOG_INT_TRIG( log_int_pos = 0); + + DFLIP( if (info->line == SERIAL_DEBUG_LINE) { + info->icount.rx = 0; + } ); + + return 0; +} + +#ifdef CONFIG_PROC_FS +/* + * /proc fs routines.... + */ + +static void seq_line_info(struct seq_file *m, struct e100_serial *info) +{ + unsigned long tmp; + + seq_printf(m, "%d: uart:E100 port:%lX irq:%d", + info->line, (unsigned long)info->ioport, info->irq); + + if (!info->ioport || (info->type == PORT_UNKNOWN)) { + seq_printf(m, "\n"); + return; + } + + seq_printf(m, " baud:%d", info->baud); + seq_printf(m, " tx:%lu rx:%lu", + (unsigned long)info->icount.tx, + (unsigned long)info->icount.rx); + tmp = CIRC_CNT(info->xmit.head, info->xmit.tail, SERIAL_XMIT_SIZE); + if (tmp) + seq_printf(m, " tx_pend:%lu/%lu", + (unsigned long)tmp, + (unsigned long)SERIAL_XMIT_SIZE); + + seq_printf(m, " rx_pend:%lu/%lu", + (unsigned long)info->recv_cnt, + (unsigned long)info->max_recv_cnt); + +#if 1 + if (info->port.tty) { + if (info->port.tty->stopped) + seq_printf(m, " stopped:%i", + (int)info->port.tty->stopped); + } + + { + unsigned char rstat = info->ioport[REG_STATUS]; + if (rstat & IO_MASK(R_SERIAL0_STATUS, xoff_detect)) + seq_printf(m, " xoff_detect:1"); + } + +#endif + + if (info->icount.frame) + seq_printf(m, " fe:%lu", (unsigned long)info->icount.frame); + + if (info->icount.parity) + seq_printf(m, " pe:%lu", (unsigned long)info->icount.parity); + + if (info->icount.brk) + seq_printf(m, " brk:%lu", (unsigned long)info->icount.brk); + + if (info->icount.overrun) + seq_printf(m, " oe:%lu", (unsigned long)info->icount.overrun); + + /* + * Last thing is the RS-232 status lines + */ + if (!E100_RTS_GET(info)) + seq_puts(m, "|RTS"); + if (!E100_CTS_GET(info)) + seq_puts(m, "|CTS"); + if (!E100_DTR_GET(info)) + seq_puts(m, "|DTR"); + if (!E100_DSR_GET(info)) + seq_puts(m, "|DSR"); + if (!E100_CD_GET(info)) + seq_puts(m, "|CD"); + if (!E100_RI_GET(info)) + seq_puts(m, "|RI"); + seq_puts(m, "\n"); +} + + +static int crisv10_proc_show(struct seq_file *m, void *v) +{ + int i; + + seq_printf(m, "serinfo:1.0 driver:%s\n", serial_version); + + for (i = 0; i < NR_PORTS; i++) { + if (!rs_table[i].enabled) + continue; + seq_line_info(m, &rs_table[i]); + } +#ifdef DEBUG_LOG_INCLUDED + for (i = 0; i < debug_log_pos; i++) { + seq_printf(m, "%-4i %lu.%lu ", + i, debug_log[i].time, + timer_data_to_ns(debug_log[i].timer_data)); + seq_printf(m, debug_log[i].string, debug_log[i].value); + } + seq_printf(m, "debug_log %i/%i\n", i, DEBUG_LOG_SIZE); + debug_log_pos = 0; +#endif + return 0; +} + +static int crisv10_proc_open(struct inode *inode, struct file *file) +{ + return single_open(file, crisv10_proc_show, NULL); +} + +static const struct file_operations crisv10_proc_fops = { + .owner = THIS_MODULE, + .open = crisv10_proc_open, + .read = seq_read, + .llseek = seq_lseek, + .release = single_release, +}; +#endif + + +/* Finally, routines used to initialize the serial driver. */ + +static void show_serial_version(void) +{ + printk(KERN_INFO + "ETRAX 100LX serial-driver %s, " + "(c) 2000-2004 Axis Communications AB\r\n", + &serial_version[11]); /* "$Revision: x.yy" */ +} + +/* rs_init inits the driver at boot (using the module_init chain) */ + +static const struct tty_operations rs_ops = { + .open = rs_open, + .close = rs_close, + .write = rs_write, + .flush_chars = rs_flush_chars, + .write_room = rs_write_room, + .chars_in_buffer = rs_chars_in_buffer, + .flush_buffer = rs_flush_buffer, + .ioctl = rs_ioctl, + .throttle = rs_throttle, + .unthrottle = rs_unthrottle, + .set_termios = rs_set_termios, + .stop = rs_stop, + .start = rs_start, + .hangup = rs_hangup, + .break_ctl = rs_break, + .send_xchar = rs_send_xchar, + .wait_until_sent = rs_wait_until_sent, + .tiocmget = rs_tiocmget, + .tiocmset = rs_tiocmset, +#ifdef CONFIG_PROC_FS + .proc_fops = &crisv10_proc_fops, +#endif +}; + +static int __init rs_init(void) +{ + int i; + struct e100_serial *info; + struct tty_driver *driver = alloc_tty_driver(NR_PORTS); + + if (!driver) + return -ENOMEM; + + show_serial_version(); + + /* Setup the timed flush handler system */ + +#if !defined(CONFIG_ETRAX_SERIAL_FAST_TIMER) + setup_timer(&flush_timer, timed_flush_handler, 0); + mod_timer(&flush_timer, jiffies + 5); +#endif + +#if defined(CONFIG_ETRAX_RS485) +#if defined(CONFIG_ETRAX_RS485_ON_PA) + if (cris_io_interface_allocate_pins(if_serial_0, 'a', rs485_pa_bit, + rs485_pa_bit)) { + printk(KERN_ERR "ETRAX100LX serial: Could not allocate " + "RS485 pin\n"); + put_tty_driver(driver); + return -EBUSY; + } +#endif +#if defined(CONFIG_ETRAX_RS485_ON_PORT_G) + if (cris_io_interface_allocate_pins(if_serial_0, 'g', rs485_pa_bit, + rs485_port_g_bit)) { + printk(KERN_ERR "ETRAX100LX serial: Could not allocate " + "RS485 pin\n"); + put_tty_driver(driver); + return -EBUSY; + } +#endif +#endif + + /* Initialize the tty_driver structure */ + + driver->driver_name = "serial"; + driver->name = "ttyS"; + driver->major = TTY_MAJOR; + driver->minor_start = 64; + driver->type = TTY_DRIVER_TYPE_SERIAL; + driver->subtype = SERIAL_TYPE_NORMAL; + driver->init_termios = tty_std_termios; + driver->init_termios.c_cflag = + B115200 | CS8 | CREAD | HUPCL | CLOCAL; /* is normally B9600 default... */ + driver->init_termios.c_ispeed = 115200; + driver->init_termios.c_ospeed = 115200; + driver->flags = TTY_DRIVER_REAL_RAW; + + tty_set_operations(driver, &rs_ops); + serial_driver = driver; + + /* do some initializing for the separate ports */ + for (i = 0, info = rs_table; i < NR_PORTS; i++,info++) { + if (info->enabled) { + if (cris_request_io_interface(info->io_if, + info->io_if_description)) { + printk(KERN_ERR "ETRAX100LX async serial: " + "Could not allocate IO pins for " + "%s, port %d\n", + info->io_if_description, i); + info->enabled = 0; + } + } + tty_port_init(&info->port); + info->uses_dma_in = 0; + info->uses_dma_out = 0; + info->line = i; + info->port.tty = NULL; + info->type = PORT_ETRAX; + info->tr_running = 0; + info->forced_eop = 0; + info->baud_base = DEF_BAUD_BASE; + info->custom_divisor = 0; + info->x_char = 0; + info->event = 0; + info->normal_termios = driver->init_termios; + info->xmit.buf = NULL; + info->xmit.tail = info->xmit.head = 0; + info->first_recv_buffer = info->last_recv_buffer = NULL; + info->recv_cnt = info->max_recv_cnt = 0; + info->last_tx_active_usec = 0; + info->last_tx_active = 0; + +#if defined(CONFIG_ETRAX_RS485) + /* Set sane defaults */ + info->rs485.flags &= ~(SER_RS485_RTS_ON_SEND); + info->rs485.flags |= SER_RS485_RTS_AFTER_SEND; + info->rs485.delay_rts_before_send = 0; + info->rs485.flags &= ~(SER_RS485_ENABLED); +#endif + INIT_WORK(&info->work, do_softint); + + if (info->enabled) { + printk(KERN_INFO "%s%d at %p is a builtin UART with DMA\n", + serial_driver->name, info->line, info->ioport); + } + tty_port_link_device(&info->port, driver, i); + } + + if (tty_register_driver(driver)) + panic("Couldn't register serial driver\n"); + +#ifdef CONFIG_ETRAX_FAST_TIMER +#ifdef CONFIG_ETRAX_SERIAL_FAST_TIMER + memset(fast_timers, 0, sizeof(fast_timers)); +#endif +#ifdef CONFIG_ETRAX_RS485 + memset(fast_timers_rs485, 0, sizeof(fast_timers_rs485)); +#endif + fast_timer_init(); +#endif + +#ifndef CONFIG_ETRAX_KGDB + /* Not needed in simulator. May only complicate stuff. */ + /* hook the irq's for DMA channel 6 and 7, serial output and input, and some more... */ + + if (request_irq(SERIAL_IRQ_NBR, ser_interrupt, + IRQF_SHARED, "serial ", driver)) + panic("%s: Failed to request irq8", __func__); + +#endif + + return 0; +} + +/* this makes sure that rs_init is called during kernel boot */ + +module_init(rs_init); |