diff options
Diffstat (limited to 'drivers/tty/serial/Kconfig')
| -rw-r--r-- | drivers/tty/serial/Kconfig | 309 |
1 files changed, 253 insertions, 56 deletions
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig index 070b442c1f8..fb57159bad3 100644 --- a/drivers/tty/serial/Kconfig +++ b/drivers/tty/serial/Kconfig @@ -2,9 +2,18 @@ # Serial device configuration # +if TTY + menu "Serial drivers" depends on HAS_IOMEM +config SERIAL_EARLYCON + bool + help + Support for early consoles with the earlycon parameter. This enables + the console before standard serial driver is probed. The console is + enabled when early_param is processed. + source "drivers/tty/serial/8250/Kconfig" comment "Non-8250 serial port support" @@ -51,6 +60,7 @@ config SERIAL_AMBA_PL011_CONSOLE bool "Support for console on AMBA serial port" depends on SERIAL_AMBA_PL011=y select SERIAL_CORE_CONSOLE + select SERIAL_EARLYCON ---help--- Say Y here if you wish to use an AMBA PrimeCell UART as the system console (the system console is the device which receives all kernel @@ -63,6 +73,18 @@ config SERIAL_AMBA_PL011_CONSOLE your boot loader (lilo or loadlin) about how to pass options to the kernel at boot time.) +config SERIAL_EARLYCON_ARM_SEMIHOST + bool "Early console using ARM semihosting" + depends on ARM64 || ARM + select SERIAL_CORE + select SERIAL_CORE_CONSOLE + select SERIAL_EARLYCON + help + Support for early debug console using ARM semihosting. This enables + the console before standard serial driver is probed. This is enabled + with "earlycon=smh" on the kernel command line. The console is + enabled when early_param is processed. + config SERIAL_SB1250_DUART tristate "BCM1xxx on-chip DUART serial support" depends on SIBYTE_SB1xxx_SOC=y @@ -93,8 +115,9 @@ config SERIAL_SB1250_DUART_CONSOLE config SERIAL_ATMEL bool "AT91 / AT32 on-chip serial port support" - depends on (ARM && ARCH_AT91) || AVR32 + depends on ARCH_AT91 || AVR32 select SERIAL_CORE + select SERIAL_MCTRL_GPIO help This enables the driver for the on-chip UARTs of the Atmel AT91 and AT32 processors. @@ -141,6 +164,25 @@ config SERIAL_ATMEL_TTYAT Say Y if you have an external 8250/16C550 UART. If unsure, say N. +config SERIAL_KGDB_NMI + bool "Serial console over KGDB NMI debugger port" + depends on KGDB_SERIAL_CONSOLE + help + This special driver allows you to temporary use NMI debugger port + as a normal console (assuming that the port is attached to KGDB). + + Unlike KDB's disable_nmi command, with this driver you are always + able to go back to the debugger using KGDB escape sequence ($3#33). + This is because this console driver processes the input in NMI + context, and thus is able to intercept the magic sequence. + + Note that since the console interprets input and uses polling + communication methods, for things like PPP you still must fully + detach debugger port from the KGDB NMI (i.e. disable_nmi), and + use raw console. + + If unsure, say N. + config SERIAL_KS8695 bool "Micrel KS8695 (Centaur) serial port support" depends on ARCH_KS8695 @@ -160,10 +202,11 @@ config SERIAL_KS8695_CONSOLE config SERIAL_CLPS711X tristate "CLPS711X serial port support" - depends on ARM && ARCH_CLPS711X + depends on ARCH_CLPS711X || COMPILE_TEST select SERIAL_CORE help - ::: To be written ::: + This enables the driver for the on-chip UARTs of the Cirrus + Logic EP711x/EP721x/EP731x processors. config SERIAL_CLPS711X_CONSOLE bool "Support for console on CLPS711X serial port" @@ -173,13 +216,11 @@ config SERIAL_CLPS711X_CONSOLE Even if you say Y here, the currently visible virtual console (/dev/tty0) will still be used as the system console by default, but you can alter that using a kernel command line option such as - "console=ttyCL1". (Try "man bootparam" or see the documentation of - your boot loader (lilo or loadlin) about how to pass options to the - kernel at boot time.) + "console=ttyCL1". config SERIAL_SAMSUNG tristate "Samsung SoC serial support" - depends on ARM && PLAT_SAMSUNG + depends on PLAT_SAMSUNG select SERIAL_CORE help Support for the on-chip UARTs on the Samsung S3C24XX series CPUs, @@ -189,15 +230,15 @@ config SERIAL_SAMSUNG config SERIAL_SAMSUNG_UARTS_4 bool - depends on ARM && PLAT_SAMSUNG - default y if !(CPU_S3C2410 || SERIAL_S3C2412 || CPU_S3C2440 || CPU_S3C2442) + depends on PLAT_SAMSUNG + default y if !(CPU_S3C2410 || CPU_S3C2412 || CPU_S3C2440 || CPU_S3C2442) help Internal node for the common case of 4 Samsung compatible UARTs config SERIAL_SAMSUNG_UARTS int - depends on ARM && PLAT_SAMSUNG - default 6 if ARCH_S5P6450 + depends on PLAT_SAMSUNG + default 6 if CPU_S5P6450 default 4 if SERIAL_SAMSUNG_UARTS_4 || CPU_S3C2416 default 3 help @@ -230,7 +271,7 @@ config SERIAL_SAMSUNG_CONSOLE config SERIAL_SIRFSOC tristate "SiRF SoC Platform Serial port support" - depends on ARM && ARCH_PRIMA2 + depends on ARCH_SIRF select SERIAL_CORE help Support for the on-chip UART on the CSR SiRFprimaII series, @@ -250,6 +291,17 @@ config SERIAL_SIRFSOC_CONSOLE your boot loader about how to pass options to the kernel at boot time.) +config SERIAL_TEGRA + tristate "NVIDIA Tegra20/30 SoC serial controller" + depends on ARCH_TEGRA && TEGRA20_APB_DMA + select SERIAL_CORE + help + Support for the on-chip UARTs on the NVIDIA Tegra series SOCs + providing /dev/ttyTHS0, 1, 2, 3 and 4 (note, some machines may not + provide all of these ports, depending on how the serial port + are enabled). This driver uses the APB DMA to achieve higher baudrate + and better performance. + config SERIAL_MAX3100 tristate "MAX3100 support" depends on SPI @@ -257,12 +309,19 @@ config SERIAL_MAX3100 help MAX3100 chip support -config SERIAL_MAX3107 - tristate "MAX3107 support" - depends on SPI +config SERIAL_MAX310X + tristate "MAX310X support" + depends on SPI_MASTER select SERIAL_CORE + select REGMAP_SPI if SPI_MASTER + default n help - MAX3107 chip support + This selects support for an advanced UART from Maxim (Dallas). + Supported ICs are MAX3107, MAX3108, MAX3109, MAX14830. + Each IC contains 128 words each of receive and transmit FIFO + that can be controlled through I2C or high-speed SPI. + + Say Y here if you want to support this ICs. config SERIAL_DZ bool "DECstation DZ serial driver" @@ -321,7 +380,7 @@ config SERIAL_ZS_CONSOLE config SERIAL_21285 tristate "DC21285 serial port support" - depends on ARM && FOOTBRIDGE + depends on FOOTBRIDGE select SERIAL_CORE help If you have a machine based on a 21285 (Footbridge) StrongARM(R)/ @@ -345,7 +404,7 @@ config SERIAL_21285_CONSOLE config SERIAL_MPSC bool "Marvell MPSC serial port support" - depends on PPC32 && MV64X60 + depends on MV64X60 select SERIAL_CORE help Say Y here if you want to use the Marvell MPSC serial controller. @@ -382,7 +441,7 @@ config SERIAL_PXA_CONSOLE config SERIAL_SA1100 bool "SA1100 serial port support" - depends on ARM && ARCH_SA1100 + depends on ARCH_SA1100 select SERIAL_CORE help If you have a machine based on a SA1100/SA1110 StrongARM(R) CPU you @@ -512,7 +571,7 @@ config BFIN_UART3_CTSRTS Enable hardware flow control in the driver. config SERIAL_IMX - bool "IMX serial port support" + tristate "IMX serial port support" depends on ARCH_MXC select SERIAL_CORE select RATIONAL @@ -522,22 +581,21 @@ config SERIAL_IMX config SERIAL_IMX_CONSOLE bool "Console on IMX serial port" - depends on SERIAL_IMX + depends on SERIAL_IMX=y select SERIAL_CORE_CONSOLE help - If you have enabled the serial port on the Motorola IMX + If you have enabled the serial port on the Freescale IMX CPU you can make it the console by answering Y to this option. Even if you say Y here, the currently visible virtual console (/dev/tty0) will still be used as the system console by default, but you can alter that using a kernel command line option such as - "console=ttySA0". (Try "man bootparam" or see the documentation of - your boot loader (lilo or loadlin) about how to pass options to the - kernel at boot time.) + "console=ttymxc0". (Try "man bootparam" or see the documentation of + your bootloader about how to pass options to the kernel at boot time.) config SERIAL_UARTLITE tristate "Xilinx uartlite serial port support" - depends on PPC32 || MICROBLAZE || MFD_TIMBERDALE + depends on PPC32 || MICROBLAZE || MFD_TIMBERDALE || ARCH_ZYNQ select SERIAL_CORE help Say Y here if you want to use the Xilinx uartlite serial controller. @@ -671,7 +729,7 @@ config SERIAL_IP22_ZILOG_CONSOLE config SERIAL_SH_SCI tristate "SuperH SCI(F) serial port support" - depends on HAVE_CLK && (SUPERH || ARCH_SHMOBILE) + depends on SUPERH || ARCH_SHMOBILE || COMPILE_TEST select SERIAL_CORE config SERIAL_SH_SCI_NR_UARTS @@ -686,23 +744,42 @@ config SERIAL_SH_SCI_CONSOLE config SERIAL_SH_SCI_DMA bool "DMA support" - depends on SERIAL_SH_SCI && SH_DMAE && EXPERIMENTAL + depends on SERIAL_SH_SCI && SH_DMAE config SERIAL_PNX8XXX bool "Enable PNX8XXX SoCs' UART Support" - depends on MIPS && (SOC_PNX8550 || SOC_PNX833X) + depends on SOC_PNX833X select SERIAL_CORE help - If you have a MIPS-based Philips SoC such as PNX8550 or PNX8330 - and you want to use serial ports, say Y. Otherwise, say N. + If you have a MIPS-based Philips SoC such as PNX8330 and you want + to use serial ports, say Y. Otherwise, say N. config SERIAL_PNX8XXX_CONSOLE bool "Enable PNX8XX0 serial console" depends on SERIAL_PNX8XXX select SERIAL_CORE_CONSOLE help - If you have a MIPS-based Philips SoC such as PNX8550 or PNX8330 - and you want to use serial console, say Y. Otherwise, say N. + If you have a MIPS-based Philips SoC such as PNX8330 and you want + to use serial console, say Y. Otherwise, say N. + +config SERIAL_HS_LPC32XX + tristate "LPC32XX high speed serial port support" + depends on ARCH_LPC32XX && OF + select SERIAL_CORE + help + Support for the LPC32XX high speed serial ports (up to 900kbps). + Those are UARTs completely different from the Standard UARTs on the + LPC32XX SoC. + Choose M or Y here to build this driver. + +config SERIAL_HS_LPC32XX_CONSOLE + bool "Enable LPC32XX high speed UART serial console" + depends on SERIAL_HS_LPC32XX + select SERIAL_CORE_CONSOLE + help + If you would like to be able to use one of the high speed serial + ports on the LPC32XX as the console, you can do so by answering + Y to this option. config SERIAL_CORE tristate @@ -968,7 +1045,7 @@ config SERIAL_SGI_IOC3 config SERIAL_MSM bool "MSM on-chip serial port support" - depends on ARM && ARCH_MSM + depends on ARCH_MSM || ARCH_QCOM select SERIAL_CORE config SERIAL_MSM_CONSOLE @@ -978,7 +1055,7 @@ config SERIAL_MSM_CONSOLE config SERIAL_MSM_HS tristate "MSM UART High Speed: Serial Driver" - depends on ARCH_MSM + depends on ARCH_MSM7X00A || ARCH_MSM7X30 || ARCH_QSD8X50 select SERIAL_CORE help If you have a machine based on MSM family of SoCs, you @@ -990,7 +1067,7 @@ config SERIAL_MSM_HS config SERIAL_VT8500 bool "VIA VT8500 on-chip serial port support" - depends on ARM && ARCH_VT8500 + depends on ARCH_VT8500 select SERIAL_CORE config SERIAL_VT8500_CONSOLE @@ -1000,7 +1077,7 @@ config SERIAL_VT8500_CONSOLE config SERIAL_NETX tristate "NetX serial port support" - depends on ARM && ARCH_NETX + depends on ARCH_NETX select SERIAL_CORE help If you have a machine based on a Hilscher NetX SoC you @@ -1089,20 +1166,30 @@ config SERIAL_QE This driver supports the QE serial ports on Freescale embedded PowerPC that contain a QUICC Engine. -config SERIAL_SC26XX - tristate "SC2681/SC2692 serial port support" - depends on SNI_RM +config SERIAL_SCCNXP + tristate "SCCNXP serial port support" select SERIAL_CORE help - This is a driver for the onboard serial ports of - older RM400 machines. + This selects support for an advanced UART from NXP (Philips). + Supported ICs are SCC2681, SCC2691, SCC2692, SC28L91, SC28L92, + SC28L202, SCC68681 and SCC68692. -config SERIAL_SC26XX_CONSOLE - bool "Console on SC2681/SC2692 serial port" - depends on SERIAL_SC26XX=y +config SERIAL_SCCNXP_CONSOLE + bool "Console on SCCNXP serial port" + depends on SERIAL_SCCNXP=y select SERIAL_CORE_CONSOLE help - Support for Console on SC2681/SC2692 serial ports. + Support for console on SCCNXP serial ports. + +config SERIAL_SC16IS7XX + tristate "SC16IS7xx serial support" + depends on I2C + select SERIAL_CORE + select REGMAP_I2C if I2C + help + This selects support for SC16IS7xx serial ports. + Supported ICs are SC16IS740, SC16IS741, SC16IS750, SC16IS752, + SC16IS760 and SC16IS762. config SERIAL_BFIN_SPORT tristate "Blackfin SPORT emulate UART" @@ -1170,6 +1257,7 @@ config SERIAL_BFIN_SPORT3_UART_CTSRTS config SERIAL_TIMBERDALE tristate "Support for timberdale UART" select SERIAL_CORE + depends on X86_32 || COMPILE_TEST ---help--- Add support for UART controller on timberdale. @@ -1260,13 +1348,13 @@ config SERIAL_ALTERA_UART_CONSOLE config SERIAL_IFX6X60 tristate "SPI protocol driver for Infineon 6x60 modem (EXPERIMENTAL)" - depends on GPIOLIB && SPI && EXPERIMENTAL + depends on GPIOLIB && SPI help Support for the IFX6x60 modem devices on Intel MID platforms. config SERIAL_PCH_UART tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) UART" - depends on PCI + depends on PCI && (X86_32 || COMPILE_TEST) select SERIAL_CORE help This driver is for PCH(Platform controller Hub) UART of Intel EG20T @@ -1312,26 +1400,31 @@ config SERIAL_MXS_AUART_CONSOLE Enable a MXS AUART port to be the system console. config SERIAL_XILINX_PS_UART - tristate "Xilinx PS UART support" + tristate "Cadence (Xilinx Zynq) UART support" + depends on OF select SERIAL_CORE help - This driver supports the Xilinx PS UART port. + This driver supports the Cadence UART. It is found e.g. in Xilinx + Zynq. config SERIAL_XILINX_PS_UART_CONSOLE - bool "Xilinx PS UART console support" + bool "Cadence UART console support" depends on SERIAL_XILINX_PS_UART=y select SERIAL_CORE_CONSOLE help - Enable a Xilinx PS UART port to be the system console. + Enable a Cadence UART port to be the system console. config SERIAL_AR933X - bool "AR933X serial port support" - depends on SOC_AR933X + tristate "AR933X serial port support" + depends on HAVE_CLK && SOC_AR933X select SERIAL_CORE help If you have an Atheros AR933X SOC based board and want to use the built-in UART of the SoC, say Y to this option. + To compile this driver as a module, choose M here: the + module will be called ar933x_uart. + config SERIAL_AR933X_CONSOLE bool "Console on AR933X serial port" depends on SERIAL_AR933X=y @@ -1348,8 +1441,8 @@ config SERIAL_AR933X_NR_UARTS to support. config SERIAL_EFM32_UART - tristate "EFM32 UART/USART port." - depends on ARCH_EFM32 + tristate "EFM32 UART/USART port" + depends on ARM && (ARCH_EFM32 || COMPILE_TEST) select SERIAL_CORE help This driver support the USART and UART ports on @@ -1360,4 +1453,108 @@ config SERIAL_EFM32_UART_CONSOLE depends on SERIAL_EFM32_UART=y select SERIAL_CORE_CONSOLE +config SERIAL_TILEGX + tristate "TILE-Gx on-chip serial port support" + depends on TILEGX + select TILE_GXIO_UART + select SERIAL_CORE + ---help--- + This device provides access to the on-chip UARTs on the TILE-Gx + processor. + +config SERIAL_ARC + tristate "ARC UART driver support" + select SERIAL_CORE + help + Driver for on-chip UART for ARC(Synopsys) for the legacy + FPGA Boards (ML50x/ARCAngel4) + +config SERIAL_ARC_CONSOLE + bool "Console on ARC UART" + depends on SERIAL_ARC=y + select SERIAL_CORE_CONSOLE + help + Enable system Console on ARC UART + +config SERIAL_ARC_NR_PORTS + int "Number of ARC UART ports" + depends on SERIAL_ARC + range 1 3 + default "1" + help + Set this to the number of serial ports you want the driver + to support. + +config SERIAL_RP2 + tristate "Comtrol RocketPort EXPRESS/INFINITY support" + depends on PCI + select SERIAL_CORE + help + This driver supports the Comtrol RocketPort EXPRESS and + RocketPort INFINITY families of PCI/PCIe multiport serial adapters. + These adapters use a "RocketPort 2" ASIC that is not compatible + with the original RocketPort driver (CONFIG_ROCKETPORT). + + To compile this driver as a module, choose M here: the + module will be called rp2. + + If you want to compile this driver into the kernel, say Y here. If + you don't have a suitable RocketPort card installed, say N. + +config SERIAL_RP2_NR_UARTS + int "Maximum number of RocketPort EXPRESS/INFINITY ports" + depends on SERIAL_RP2 + default "32" + help + If multiple cards are present, the default limit of 32 ports may + need to be increased. + +config SERIAL_FSL_LPUART + tristate "Freescale lpuart serial port support" + depends on HAS_DMA + select SERIAL_CORE + help + Support for the on-chip lpuart on some Freescale SOCs. + +config SERIAL_FSL_LPUART_CONSOLE + bool "Console on Freescale lpuart serial port" + depends on SERIAL_FSL_LPUART=y + select SERIAL_CORE_CONSOLE + help + If you have enabled the lpuart serial port on the Freescale SoCs, + you can make it the console by answering Y to this option. + +config SERIAL_ST_ASC + tristate "ST ASC serial port support" + select SERIAL_CORE + depends on ARM || COMPILE_TEST + help + This driver is for the on-chip Asychronous Serial Controller on + STMicroelectronics STi SoCs. + ASC is embedded in ST COMMS IP block. It supports Rx & Tx functionality. + It support all industry standard baud rates. + + If unsure, say N. + +config SERIAL_ST_ASC_CONSOLE + bool "Support for console on ST ASC" + depends on SERIAL_ST_ASC=y + select SERIAL_CORE_CONSOLE + +config SERIAL_MEN_Z135 + tristate "MEN 16z135 Support" + select SERIAL_CORE + depends on MCB + help + Say yes here to enable support for the MEN 16z135 High Speed UART IP-Core + on a MCB carrier. + + This driver can also be build as a module. If so, the module will be called + men_z135_uart.ko + endmenu + +config SERIAL_MCTRL_GPIO + tristate + +endif # TTY |