diff options
Diffstat (limited to 'drivers/tty/serial/8250')
| -rw-r--r-- | drivers/tty/serial/8250/8250_core.c | 58 | ||||
| -rw-r--r-- | drivers/tty/serial/8250/8250_dma.c | 26 | ||||
| -rw-r--r-- | drivers/tty/serial/8250/8250_dw.c | 102 | ||||
| -rw-r--r-- | drivers/tty/serial/8250/8250_early.c | 139 | ||||
| -rw-r--r-- | drivers/tty/serial/8250/8250_em.c | 1 | ||||
| -rw-r--r-- | drivers/tty/serial/8250/8250_pci.c | 74 | ||||
| -rw-r--r-- | drivers/tty/serial/8250/8250_pnp.c | 1 | ||||
| -rw-r--r-- | drivers/tty/serial/8250/Kconfig | 6 | ||||
| -rw-r--r-- | drivers/tty/serial/8250/serial_cs.c | 1 |
9 files changed, 226 insertions, 182 deletions
diff --git a/drivers/tty/serial/8250/8250_core.c b/drivers/tty/serial/8250/8250_core.c index e33d38cb170..7a91c6d1eb7 100644 --- a/drivers/tty/serial/8250/8250_core.c +++ b/drivers/tty/serial/8250/8250_core.c @@ -555,7 +555,7 @@ static void serial8250_set_sleep(struct uart_8250_port *p, int sleep) */ if ((p->port.type == PORT_XR17V35X) || (p->port.type == PORT_XR17D15X)) { - serial_out(p, UART_EXAR_SLEEP, 0xff); + serial_out(p, UART_EXAR_SLEEP, sleep ? 0xff : 0); return; } @@ -1520,7 +1520,7 @@ int serial8250_handle_irq(struct uart_port *port, unsigned int iir) status = serial8250_rx_chars(up, status); } serial8250_modem_status(up); - if (status & UART_LSR_THRE) + if (!up->dma && (status & UART_LSR_THRE)) serial8250_tx_chars(up); spin_unlock_irqrestore(&port->lock, flags); @@ -1694,6 +1694,10 @@ static int serial_link_irq_chain(struct uart_8250_port *up) static void serial_unlink_irq_chain(struct uart_8250_port *up) { + /* + * yes, some broken gcc emit "warning: 'i' may be used uninitialized" + * but no, we are not going to take a patch that assigns NULL below. + */ struct irq_info *i; struct hlist_node *n; struct hlist_head *h; @@ -1922,13 +1926,8 @@ static void serial8250_put_poll_char(struct uart_port *port, wait_for_xmitr(up, BOTH_EMPTY); /* * Send the character out. - * If a LF, also do CR... */ serial_port_out(port, UART_TX, c); - if (c == 10) { - wait_for_xmitr(up, BOTH_EMPTY); - serial_port_out(port, UART_TX, 13); - } /* * Finally, wait for transmitter to become empty @@ -2334,9 +2333,11 @@ serial8250_do_set_termios(struct uart_port *port, struct ktermios *termios, * the trigger, or the MCR RTS bit is cleared. In the case where * the remote UART is not using CTS auto flow control, we must * have sufficient FIFO entries for the latency of the remote - * UART to respond. IOW, at least 32 bytes of FIFO. + * UART to respond. IOW, at least 32 bytes of FIFO. Also enable + * AFE if hw flow control is supported */ - if (up->capabilities & UART_CAP_AFE && port->fifosize >= 32) { + if ((up->capabilities & UART_CAP_AFE && (port->fifosize >= 32)) || + (port->flags & UPF_HARD_FLOW)) { up->mcr &= ~UART_MCR_AFE; if (termios->c_cflag & CRTSCTS) up->mcr |= UART_MCR_AFE; @@ -2356,7 +2357,7 @@ serial8250_do_set_termios(struct uart_port *port, struct ktermios *termios, port->read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR; if (termios->c_iflag & INPCK) port->read_status_mask |= UART_LSR_FE | UART_LSR_PE; - if (termios->c_iflag & (BRKINT | PARMRK)) + if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK)) port->read_status_mask |= UART_LSR_BI; /* @@ -2433,6 +2434,24 @@ serial8250_do_set_termios(struct uart_port *port, struct ktermios *termios, serial_dl_write(up, quot); /* + * XR17V35x UARTs have an extra fractional divisor register (DLD) + * + * We need to recalculate all of the registers, because DLM and DLL + * are already rounded to a whole integer. + * + * When recalculating we use a 32x clock instead of a 16x clock to + * allow 1-bit for rounding in the fractional part. + */ + if (up->port.type == PORT_XR17V35X) { + unsigned int baud_x32 = (port->uartclk * 2) / baud; + u16 quot = baud_x32 / 32; + u8 quot_frac = DIV_ROUND_CLOSEST(baud_x32 % 32, 2); + + serial_dl_write(up, quot); + serial_port_out(port, 0x2, quot_frac & 0xf); + } + + /* * LCR DLAB must be set to enable 64-byte FIFO mode. If the FCR * is written without DLAB set, this mode will be disabled. */ @@ -2670,6 +2689,10 @@ static void serial8250_config_port(struct uart_port *port, int flags) if (port->type == PORT_16550A && port->iotype == UPIO_AU) up->bugs |= UART_BUG_NOMSR; + /* HW bugs may trigger IRQ while IIR == NO_INT */ + if (port->type == PORT_TEGRA) + up->bugs |= UART_BUG_NOMSR; + if (port->type != PORT_UNKNOWN && flags & UART_CONFIG_IRQ) autoconfig_irq(up); @@ -2860,14 +2883,10 @@ serial8250_console_write(struct console *co, const char *s, unsigned int count) touch_nmi_watchdog(); - local_irq_save(flags); - if (port->sysrq) { - /* serial8250_handle_irq() already took the lock */ - locked = 0; - } else if (oops_in_progress) { - locked = spin_trylock(&port->lock); - } else - spin_lock(&port->lock); + if (port->sysrq || oops_in_progress) + locked = spin_trylock_irqsave(&port->lock, flags); + else + spin_lock_irqsave(&port->lock, flags); /* * First save the IER then disable the interrupts @@ -2899,8 +2918,7 @@ serial8250_console_write(struct console *co, const char *s, unsigned int count) serial8250_modem_status(up); if (locked) - spin_unlock(&port->lock); - local_irq_restore(flags); + spin_unlock_irqrestore(&port->lock, flags); } static int __init serial8250_console_setup(struct console *co, char *options) diff --git a/drivers/tty/serial/8250/8250_dma.c b/drivers/tty/serial/8250/8250_dma.c index 7046769608d..148ffe4c232 100644 --- a/drivers/tty/serial/8250/8250_dma.c +++ b/drivers/tty/serial/8250/8250_dma.c @@ -20,12 +20,15 @@ static void __dma_tx_complete(void *param) struct uart_8250_port *p = param; struct uart_8250_dma *dma = p->dma; struct circ_buf *xmit = &p->port.state->xmit; - - dma->tx_running = 0; + unsigned long flags; dma_sync_single_for_cpu(dma->txchan->device->dev, dma->tx_addr, UART_XMIT_SIZE, DMA_TO_DEVICE); + spin_lock_irqsave(&p->port.lock, flags); + + dma->tx_running = 0; + xmit->tail += dma->tx_size; xmit->tail &= UART_XMIT_SIZE - 1; p->port.icount.tx += dma->tx_size; @@ -35,6 +38,8 @@ static void __dma_tx_complete(void *param) if (!uart_circ_empty(xmit) && !uart_tx_stopped(&p->port)) serial8250_tx_dma(p); + + spin_unlock_irqrestore(&p->port.lock, flags); } static void __dma_rx_complete(void *param) @@ -187,21 +192,28 @@ int serial8250_request_dma(struct uart_8250_port *p) dma->rx_buf = dma_alloc_coherent(dma->rxchan->device->dev, dma->rx_size, &dma->rx_addr, GFP_KERNEL); - if (!dma->rx_buf) { - dma_release_channel(dma->rxchan); - dma_release_channel(dma->txchan); - return -ENOMEM; - } + if (!dma->rx_buf) + goto err; /* TX buffer */ dma->tx_addr = dma_map_single(dma->txchan->device->dev, p->port.state->xmit.buf, UART_XMIT_SIZE, DMA_TO_DEVICE); + if (dma_mapping_error(dma->txchan->device->dev, dma->tx_addr)) { + dma_free_coherent(dma->rxchan->device->dev, dma->rx_size, + dma->rx_buf, dma->rx_addr); + goto err; + } dev_dbg_ratelimited(p->port.dev, "got both dma channels\n"); return 0; +err: + dma_release_channel(dma->rxchan); + dma_release_channel(dma->txchan); + + return -ENOMEM; } EXPORT_SYMBOL_GPL(serial8250_request_dma); diff --git a/drivers/tty/serial/8250/8250_dw.c b/drivers/tty/serial/8250/8250_dw.c index 4658e3e0ec4..51b307aab75 100644 --- a/drivers/tty/serial/8250/8250_dw.c +++ b/drivers/tty/serial/8250/8250_dw.c @@ -14,7 +14,6 @@ * raised, the LCR needs to be rewritten and the uart status register read. */ #include <linux/device.h> -#include <linux/init.h> #include <linux/io.h> #include <linux/module.h> #include <linux/serial_8250.h> @@ -63,6 +62,70 @@ struct dw8250_data { struct uart_8250_dma dma; }; +struct dw8250_acpi_desc { + void (*set_termios)(struct uart_port *p, struct ktermios *termios, + struct ktermios *old); +}; + +#define BYT_PRV_CLK 0x800 +#define BYT_PRV_CLK_EN (1 << 0) +#define BYT_PRV_CLK_M_VAL_SHIFT 1 +#define BYT_PRV_CLK_N_VAL_SHIFT 16 +#define BYT_PRV_CLK_UPDATE (1 << 31) + +static void byt_set_termios(struct uart_port *p, struct ktermios *termios, + struct ktermios *old) +{ + unsigned int baud = tty_termios_baud_rate(termios); + unsigned int m, n; + u32 reg; + + /* + * For baud rates 0.5M, 1M, 1.5M, 2M, 2.5M, 3M, 3.5M and 4M the + * dividers must be adjusted. + * + * uartclk = (m / n) * 100 MHz, where m <= n + */ + switch (baud) { + case 500000: + case 1000000: + case 2000000: + case 4000000: + m = 64; + n = 100; + p->uartclk = 64000000; + break; + case 3500000: + m = 56; + n = 100; + p->uartclk = 56000000; + break; + case 1500000: + case 3000000: + m = 48; + n = 100; + p->uartclk = 48000000; + break; + case 2500000: + m = 40; + n = 100; + p->uartclk = 40000000; + break; + default: + m = 2304; + n = 3125; + p->uartclk = 73728000; + } + + /* Reset the clock */ + reg = (m << BYT_PRV_CLK_M_VAL_SHIFT) | (n << BYT_PRV_CLK_N_VAL_SHIFT); + writel(reg, p->membase + BYT_PRV_CLK); + reg |= BYT_PRV_CLK_EN | BYT_PRV_CLK_UPDATE; + writel(reg, p->membase + BYT_PRV_CLK); + + serial8250_do_set_termios(p, termios, old); +} + static inline int dw8250_modify_msr(struct uart_port *p, int offset, int value) { struct dw8250_data *d = p->private_data; @@ -96,7 +159,8 @@ static void dw8250_serial_out(struct uart_port *p, int offset, int value) if (offset == UART_LCR) { int tries = 1000; while (tries--) { - if (value == p->serial_in(p, UART_LCR)) + unsigned int lcr = p->serial_in(p, UART_LCR); + if ((value & ~UART_LCR_SPAR) == (lcr & ~UART_LCR_SPAR)) return; dw8250_force_idle(p); writeb(value, p->membase + (UART_LCR << p->regshift)); @@ -132,7 +196,8 @@ static void dw8250_serial_out32(struct uart_port *p, int offset, int value) if (offset == UART_LCR) { int tries = 1000; while (tries--) { - if (value == p->serial_in(p, UART_LCR)) + unsigned int lcr = p->serial_in(p, UART_LCR); + if ((value & ~UART_LCR_SPAR) == (lcr & ~UART_LCR_SPAR)) return; dw8250_force_idle(p); writel(value, p->membase + (UART_LCR << p->regshift)); @@ -272,12 +337,12 @@ static int dw8250_probe_of(struct uart_port *p, return 0; } -#ifdef CONFIG_ACPI static int dw8250_probe_acpi(struct uart_8250_port *up, struct dw8250_data *data) { const struct acpi_device_id *id; struct uart_port *p = &up->port; + struct dw8250_acpi_desc *acpi_desc; dw8250_setup_port(up); @@ -290,23 +355,20 @@ static int dw8250_probe_acpi(struct uart_8250_port *up, p->serial_out = dw8250_serial_out32; p->regshift = 2; - if (!p->uartclk) - p->uartclk = (unsigned int)id->driver_data; - up->dma = &data->dma; up->dma->rxconf.src_maxburst = p->fifosize / 4; up->dma->txconf.dst_maxburst = p->fifosize / 4; + acpi_desc = (struct dw8250_acpi_desc *)id->driver_data; + if (!acpi_desc) + return 0; + + if (acpi_desc->set_termios) + p->set_termios = acpi_desc->set_termios; + return 0; } -#else -static inline int dw8250_probe_acpi(struct uart_8250_port *up, - struct dw8250_data *data) -{ - return -ENODEV; -} -#endif /* CONFIG_ACPI */ static int dw8250_probe(struct platform_device *pdev) { @@ -398,7 +460,7 @@ static int dw8250_remove(struct platform_device *pdev) return 0; } -#ifdef CONFIG_PM +#ifdef CONFIG_PM_SLEEP static int dw8250_suspend(struct device *dev) { struct dw8250_data *data = dev_get_drvdata(dev); @@ -416,7 +478,7 @@ static int dw8250_resume(struct device *dev) return 0; } -#endif /* CONFIG_PM */ +#endif /* CONFIG_PM_SLEEP */ #ifdef CONFIG_PM_RUNTIME static int dw8250_runtime_suspend(struct device *dev) @@ -452,10 +514,16 @@ static const struct of_device_id dw8250_of_match[] = { }; MODULE_DEVICE_TABLE(of, dw8250_of_match); +static struct dw8250_acpi_desc byt_8250_desc = { + .set_termios = byt_set_termios, +}; + static const struct acpi_device_id dw8250_acpi_match[] = { { "INT33C4", 0 }, { "INT33C5", 0 }, - { "80860F0A", 0 }, + { "INT3434", 0 }, + { "INT3435", 0 }, + { "80860F0A", (kernel_ulong_t)&byt_8250_desc}, { }, }; MODULE_DEVICE_TABLE(acpi, dw8250_acpi_match); diff --git a/drivers/tty/serial/8250/8250_early.c b/drivers/tty/serial/8250/8250_early.c index c100d6343d5..4858b8a99d3 100644 --- a/drivers/tty/serial/8250/8250_early.c +++ b/drivers/tty/serial/8250/8250_early.c @@ -35,18 +35,8 @@ #include <linux/serial_8250.h> #include <asm/io.h> #include <asm/serial.h> -#ifdef CONFIG_FIX_EARLYCON_MEM -#include <asm/pgtable.h> -#include <asm/fixmap.h> -#endif -struct early_serial8250_device { - struct uart_port port; - char options[16]; /* e.g., 115200n8 */ - unsigned int baud; -}; - -static struct early_serial8250_device early_device; +static struct earlycon_device *early_device; unsigned int __weak __init serial8250_early_in(struct uart_port *port, int offset) { @@ -100,7 +90,7 @@ static void __init serial_putc(struct uart_port *port, int c) static void __init early_serial8250_write(struct console *console, const char *s, unsigned int count) { - struct uart_port *port = &early_device.port; + struct uart_port *port = &early_device->port; unsigned int ier; /* Save the IER and disable interrupts */ @@ -129,7 +119,7 @@ static unsigned int __init probe_baud(struct uart_port *port) return (port->uartclk / 16) / quot; } -static void __init init_port(struct early_serial8250_device *device) +static void __init init_port(struct earlycon_device *device) { struct uart_port *port = &device->port; unsigned int divisor; @@ -148,128 +138,45 @@ static void __init init_port(struct early_serial8250_device *device) serial8250_early_out(port, UART_LCR, c & ~UART_LCR_DLAB); } -static int __init parse_options(struct early_serial8250_device *device, - char *options) +static int __init early_serial8250_setup(struct earlycon_device *device, + const char *options) { - struct uart_port *port = &device->port; - int mmio, mmio32, length; - - if (!options) - return -ENODEV; - - port->uartclk = BASE_BAUD * 16; - - mmio = !strncmp(options, "mmio,", 5); - mmio32 = !strncmp(options, "mmio32,", 7); - if (mmio || mmio32) { - port->iotype = (mmio ? UPIO_MEM : UPIO_MEM32); - port->mapbase = simple_strtoul(options + (mmio ? 5 : 7), - &options, 0); - if (mmio32) - port->regshift = 2; -#ifdef CONFIG_FIX_EARLYCON_MEM - set_fixmap_nocache(FIX_EARLYCON_MEM_BASE, - port->mapbase & PAGE_MASK); - port->membase = - (void __iomem *)__fix_to_virt(FIX_EARLYCON_MEM_BASE); - port->membase += port->mapbase & ~PAGE_MASK; -#else - port->membase = ioremap_nocache(port->mapbase, 64); - if (!port->membase) { - printk(KERN_ERR "%s: Couldn't ioremap 0x%llx\n", - __func__, - (unsigned long long) port->mapbase); - return -ENOMEM; - } -#endif - } else if (!strncmp(options, "io,", 3)) { - port->iotype = UPIO_PORT; - port->iobase = simple_strtoul(options + 3, &options, 0); - mmio = 0; - } else - return -EINVAL; + if (!(device->port.membase || device->port.iobase)) + return 0; - options = strchr(options, ','); - if (options) { - options++; - device->baud = simple_strtoul(options, NULL, 0); - length = min(strcspn(options, " ") + 1, - (size_t)(sizeof(device->options))); - strlcpy(device->options, options, length); - } else { - device->baud = probe_baud(port); + if (!device->baud) { + device->baud = probe_baud(&device->port); snprintf(device->options, sizeof(device->options), "%u", - device->baud); + device->baud); } - if (mmio || mmio32) - printk(KERN_INFO - "Early serial console at MMIO%s 0x%llx (options '%s')\n", - mmio32 ? "32" : "", - (unsigned long long)port->mapbase, - device->options); - else - printk(KERN_INFO - "Early serial console at I/O port 0x%lx (options '%s')\n", - port->iobase, - device->options); - - return 0; -} - -static struct console early_serial8250_console __initdata = { - .name = "uart", - .write = early_serial8250_write, - .flags = CON_PRINTBUFFER | CON_BOOT, - .index = -1, -}; - -static int __init early_serial8250_setup(char *options) -{ - struct early_serial8250_device *device = &early_device; - int err; - - if (device->port.membase || device->port.iobase) - return 0; - - err = parse_options(device, options); - if (err < 0) - return err; - init_port(device); + + early_device = device; + device->con->write = early_serial8250_write; return 0; } +EARLYCON_DECLARE(uart8250, early_serial8250_setup); +EARLYCON_DECLARE(uart, early_serial8250_setup); int __init setup_early_serial8250_console(char *cmdline) { - char *options; - int err; + char match[] = "uart8250"; - options = strstr(cmdline, "uart8250,"); - if (!options) { - options = strstr(cmdline, "uart,"); - if (!options) - return 0; - } - - options = strchr(cmdline, ',') + 1; - err = early_serial8250_setup(options); - if (err < 0) - return err; - - register_console(&early_serial8250_console); + if (cmdline && cmdline[4] == ',') + match[4] = '\0'; - return 0; + return setup_earlycon(cmdline, match, early_serial8250_setup); } int serial8250_find_port_for_earlycon(void) { - struct early_serial8250_device *device = &early_device; - struct uart_port *port = &device->port; + struct earlycon_device *device = early_device; + struct uart_port *port = device ? &device->port : NULL; int line; int ret; - if (!device->port.membase && !device->port.iobase) + if (!port || (!port->membase && !port->iobase)) return -ENODEV; line = serial8250_find_port(port); @@ -284,5 +191,3 @@ int serial8250_find_port_for_earlycon(void) return ret; } - -early_param("earlycon", setup_early_serial8250_console); diff --git a/drivers/tty/serial/8250/8250_em.c b/drivers/tty/serial/8250/8250_em.c index d1a9078003b..56c87232b6a 100644 --- a/drivers/tty/serial/8250/8250_em.c +++ b/drivers/tty/serial/8250/8250_em.c @@ -18,7 +18,6 @@ */ #include <linux/device.h> -#include <linux/init.h> #include <linux/io.h> #include <linux/module.h> #include <linux/serial_8250.h> diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c index 4697a514b80..33137b3ba94 100644 --- a/drivers/tty/serial/8250/8250_pci.c +++ b/drivers/tty/serial/8250/8250_pci.c @@ -11,7 +11,6 @@ */ #undef DEBUG #include <linux/module.h> -#include <linux/init.h> #include <linux/pci.h> #include <linux/string.h> #include <linux/kernel.h> @@ -784,7 +783,8 @@ static int pci_netmos_9900_setup(struct serial_private *priv, { unsigned int bar; - if ((priv->dev->subsystem_device & 0xff00) == 0x3000) { + if ((priv->dev->device != PCI_DEVICE_ID_NETMOS_9865) && + (priv->dev->subsystem_device & 0xff00) == 0x3000) { /* netmos apparently orders BARs by datasheet layout, so serial * ports get BARs 0 and 3 (or 1 and 4 for memmapped) */ @@ -1259,10 +1259,10 @@ static int pci_quatech_init(struct pci_dev *dev) unsigned long base = pci_resource_start(dev, 0); if (base) { u32 tmp; - outl(inl(base + 0x38), base + 0x38); + outl(inl(base + 0x38) | 0x00002000, base + 0x38); tmp = inl(base + 0x3c); outl(tmp | 0x01000000, base + 0x3c); - outl(tmp, base + 0x3c); + outl(tmp &= ~0x01000000, base + 0x3c); } } return 0; @@ -1366,23 +1366,44 @@ byt_set_termios(struct uart_port *p, struct ktermios *termios, struct ktermios *old) { unsigned int baud = tty_termios_baud_rate(termios); - unsigned int m = 6912; - unsigned int n = 15625; + unsigned int m, n; u32 reg; - /* For baud rates 1M, 2M, 3M and 4M the dividers must be adjusted. */ - if (baud == 1000000 || baud == 2000000 || baud == 4000000) { + /* + * For baud rates 0.5M, 1M, 1.5M, 2M, 2.5M, 3M, 3.5M and 4M the + * dividers must be adjusted. + * + * uartclk = (m / n) * 100 MHz, where m <= n + */ + switch (baud) { + case 500000: + case 1000000: + case 2000000: + case 4000000: m = 64; n = 100; - p->uartclk = 64000000; - } else if (baud == 3000000) { + break; + case 3500000: + m = 56; + n = 100; + p->uartclk = 56000000; + break; + case 1500000: + case 3000000: m = 48; n = 100; - p->uartclk = 48000000; - } else { - p->uartclk = 44236800; + break; + case 2500000: + m = 40; + n = 100; + p->uartclk = 40000000; + break; + default: + m = 2304; + n = 3125; + p->uartclk = 73728000; } /* Reset the clock */ @@ -1732,6 +1753,8 @@ pci_wch_ch353_setup(struct serial_private *priv, #define PCI_VENDOR_ID_ADVANTECH 0x13fe #define PCI_DEVICE_ID_INTEL_CE4100_UART 0x2e66 #define PCI_DEVICE_ID_ADVANTECH_PCI3620 0x3620 +#define PCI_DEVICE_ID_ADVANTECH_PCI3618 0x3618 +#define PCI_DEVICE_ID_ADVANTECH_PCIf618 0xf618 #define PCI_DEVICE_ID_TITAN_200I 0x8028 #define PCI_DEVICE_ID_TITAN_400I 0x8048 #define PCI_DEVICE_ID_TITAN_800I 0x8088 @@ -1744,6 +1767,7 @@ pci_wch_ch353_setup(struct serial_private *priv, #define PCI_DEVICE_ID_TITAN_800E 0xA014 #define PCI_DEVICE_ID_TITAN_200EI 0xA016 #define PCI_DEVICE_ID_TITAN_200EISI 0xA017 +#define PCI_DEVICE_ID_TITAN_200V3 0xA306 #define PCI_DEVICE_ID_TITAN_400V3 0xA310 #define PCI_DEVICE_ID_TITAN_410V3 0xA312 #define PCI_DEVICE_ID_TITAN_800V3 0xA314 @@ -1756,6 +1780,7 @@ pci_wch_ch353_setup(struct serial_private *priv, #define PCI_DEVICE_ID_WCH_CH352_2S 0x3253 #define PCI_DEVICE_ID_WCH_CH353_4S 0x3453 #define PCI_DEVICE_ID_WCH_CH353_2S1PF 0x5046 +#define PCI_DEVICE_ID_WCH_CH353_1S1P 0x5053 #define PCI_DEVICE_ID_WCH_CH353_2S1P 0x7053 #define PCI_VENDOR_ID_AGESTAR 0x5372 #define PCI_DEVICE_ID_AGESTAR_9375 0x6872 @@ -2388,6 +2413,14 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = { .subdevice = PCI_ANY_ID, .setup = pci_omegapci_setup, }, + /* WCH CH353 1S1P card (16550 clone) */ + { + .vendor = PCI_VENDOR_ID_WCH, + .device = PCI_DEVICE_ID_WCH_CH353_1S1P, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .setup = pci_wch_ch353_setup, + }, /* WCH CH353 2S1P card (16550 clone) */ { .vendor = PCI_VENDOR_ID_WCH, @@ -3448,6 +3481,10 @@ static struct pciserial_board pci_boards[] = { .base_baud = 921600, .reg_shift = 2, }, + /* + * Intel BayTrail HSUART reference clock is 44.2368 MHz at power-on, + * but is overridden by byt_set_termios. + */ [pbn_byt] = { .flags = FL_BASE0, .num_ports = 1, @@ -3500,6 +3537,7 @@ static const struct pci_device_id blacklist[] = { /* multi-io cards handled by parport_serial */ { PCI_DEVICE(0x4348, 0x7053), }, /* WCH CH353 2S1P */ + { PCI_DEVICE(0x4348, 0x5053), }, /* WCH CH353 1S1P */ }; /* @@ -3854,6 +3892,13 @@ static struct pci_device_id serial_pci_tbl[] = { { PCI_VENDOR_ID_ADVANTECH, PCI_DEVICE_ID_ADVANTECH_PCI3620, PCI_DEVICE_ID_ADVANTECH_PCI3620, 0x0001, 0, 0, pbn_b2_8_921600 }, + /* Advantech also use 0x3618 and 0xf618 */ + { PCI_VENDOR_ID_ADVANTECH, PCI_DEVICE_ID_ADVANTECH_PCI3618, + PCI_DEVICE_ID_ADVANTECH_PCI3618, PCI_ANY_ID, 0, 0, + pbn_b0_4_921600 }, + { PCI_VENDOR_ID_ADVANTECH, PCI_DEVICE_ID_ADVANTECH_PCIf618, + PCI_DEVICE_ID_ADVANTECH_PCI3618, PCI_ANY_ID, 0, 0, + pbn_b0_4_921600 }, { PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V960, PCI_SUBVENDOR_ID_CONNECT_TECH, PCI_SUBDEVICE_ID_CONNECT_TECH_BH8_232, 0, 0, @@ -4427,6 +4472,9 @@ static struct pci_device_id serial_pci_tbl[] = { { PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_200EISI, PCI_ANY_ID, PCI_ANY_ID, 0, 0, pbn_oxsemi_2_4000000 }, + { PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_200V3, + PCI_ANY_ID, PCI_ANY_ID, 0, 0, + pbn_b0_bt_2_921600 }, { PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_400V3, PCI_ANY_ID, PCI_ANY_ID, 0, 0, pbn_b0_4_921600 }, diff --git a/drivers/tty/serial/8250/8250_pnp.c b/drivers/tty/serial/8250/8250_pnp.c index 35d9ab95c5c..682a2fbe5c0 100644 --- a/drivers/tty/serial/8250/8250_pnp.c +++ b/drivers/tty/serial/8250/8250_pnp.c @@ -12,7 +12,6 @@ * the Free Software Foundation; either version 2 of the License. */ #include <linux/module.h> -#include <linux/init.h> #include <linux/pci.h> #include <linux/pnp.h> #include <linux/string.h> diff --git a/drivers/tty/serial/8250/Kconfig b/drivers/tty/serial/8250/Kconfig index 23329918f22..349ee598b34 100644 --- a/drivers/tty/serial/8250/Kconfig +++ b/drivers/tty/serial/8250/Kconfig @@ -61,6 +61,7 @@ config SERIAL_8250_CONSOLE bool "Console on 8250/16550 and compatible serial port" depends on SERIAL_8250=y select SERIAL_CORE_CONSOLE + select SERIAL_EARLYCON ---help--- If you say Y here, it will be possible to use a serial port as the system console (the system console is the device which receives all @@ -90,11 +91,6 @@ config SERIAL_8250_CONSOLE If unsure, say N. -config FIX_EARLYCON_MEM - bool - depends on X86 - default y - config SERIAL_8250_GSC tristate depends on SERIAL_8250 && GSC diff --git a/drivers/tty/serial/8250/serial_cs.c b/drivers/tty/serial/8250/serial_cs.c index 1b74b88e1e1..4d180c9423e 100644 --- a/drivers/tty/serial/8250/serial_cs.c +++ b/drivers/tty/serial/8250/serial_cs.c @@ -34,7 +34,6 @@ #include <linux/module.h> #include <linux/moduleparam.h> #include <linux/kernel.h> -#include <linux/init.h> #include <linux/ptrace.h> #include <linux/slab.h> #include <linux/string.h> |