diff options
Diffstat (limited to 'drivers/serial/omap-serial.c')
| -rw-r--r-- | drivers/serial/omap-serial.c | 34 |
1 files changed, 17 insertions, 17 deletions
diff --git a/drivers/serial/omap-serial.c b/drivers/serial/omap-serial.c index 03a96db67de..1201eff1831 100644 --- a/drivers/serial/omap-serial.c +++ b/drivers/serial/omap-serial.c @@ -570,7 +570,7 @@ serial_omap_configure_xonxoff unsigned char efr = 0; up->lcr = serial_in(up, UART_LCR); - serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB); + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); up->efr = serial_in(up, UART_EFR); serial_out(up, UART_EFR, up->efr & ~UART_EFR_ECB); @@ -598,7 +598,7 @@ serial_omap_configure_xonxoff efr |= OMAP_UART_SW_RX; serial_out(up, UART_EFR, up->efr | UART_EFR_ECB); - serial_out(up, UART_LCR, UART_LCR_DLAB); + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); up->mcr = serial_in(up, UART_MCR); @@ -612,14 +612,14 @@ serial_omap_configure_xonxoff up->mcr |= UART_MCR_XONANY; serial_out(up, UART_MCR, up->mcr | UART_MCR_TCRTLR); - serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB); + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); serial_out(up, UART_TI752_TCR, OMAP_UART_TCR_TRIG); /* Enable special char function UARTi.EFR_REG[5] and * load the new software flow control mode IXON or IXOFF * and restore the UARTi.EFR_REG[4] ENHANCED_EN value. */ serial_out(up, UART_EFR, efr | UART_EFR_SCD); - serial_out(up, UART_LCR, UART_LCR_DLAB); + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); serial_out(up, UART_MCR, up->mcr & ~UART_MCR_TCRTLR); serial_out(up, UART_LCR, up->lcr); @@ -724,22 +724,22 @@ serial_omap_set_termios(struct uart_port *port, struct ktermios *termios, * baud clock is not running * DLL_REG and DLH_REG set to 0. */ - serial_out(up, UART_LCR, UART_LCR_DLAB); + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); serial_out(up, UART_DLL, 0); serial_out(up, UART_DLM, 0); serial_out(up, UART_LCR, 0); - serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB); + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); up->efr = serial_in(up, UART_EFR); serial_out(up, UART_EFR, up->efr | UART_EFR_ECB); - serial_out(up, UART_LCR, UART_LCR_DLAB); + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); up->mcr = serial_in(up, UART_MCR); serial_out(up, UART_MCR, up->mcr | UART_MCR_TCRTLR); /* FIFO ENABLE, DMA MODE */ serial_out(up, UART_FCR, up->fcr); - serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB); + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); if (up->use_dma) { serial_out(up, UART_TI752_TLR, 0); @@ -748,27 +748,27 @@ serial_omap_set_termios(struct uart_port *port, struct ktermios *termios, } serial_out(up, UART_EFR, up->efr); - serial_out(up, UART_LCR, UART_LCR_DLAB); + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); serial_out(up, UART_MCR, up->mcr); /* Protocol, Baud Rate, and Interrupt Settings */ serial_out(up, UART_OMAP_MDR1, UART_OMAP_MDR1_DISABLE); - serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB); + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); up->efr = serial_in(up, UART_EFR); serial_out(up, UART_EFR, up->efr | UART_EFR_ECB); serial_out(up, UART_LCR, 0); serial_out(up, UART_IER, 0); - serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB); + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); serial_out(up, UART_DLL, quot & 0xff); /* LS of divisor */ serial_out(up, UART_DLM, quot >> 8); /* MS of divisor */ serial_out(up, UART_LCR, 0); serial_out(up, UART_IER, up->ier); - serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB); + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); serial_out(up, UART_EFR, up->efr); serial_out(up, UART_LCR, cval); @@ -782,18 +782,18 @@ serial_omap_set_termios(struct uart_port *port, struct ktermios *termios, if (termios->c_cflag & CRTSCTS) { efr |= (UART_EFR_CTS | UART_EFR_RTS); - serial_out(up, UART_LCR, UART_LCR_DLAB); + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); up->mcr = serial_in(up, UART_MCR); serial_out(up, UART_MCR, up->mcr | UART_MCR_TCRTLR); - serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB); + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); up->efr = serial_in(up, UART_EFR); serial_out(up, UART_EFR, up->efr | UART_EFR_ECB); serial_out(up, UART_TI752_TCR, OMAP_UART_TCR_TRIG); serial_out(up, UART_EFR, efr); /* Enable AUTORTS and AUTOCTS */ - serial_out(up, UART_LCR, UART_LCR_DLAB); + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); serial_out(up, UART_MCR, up->mcr | UART_MCR_RTS); serial_out(up, UART_LCR, cval); } @@ -815,13 +815,13 @@ serial_omap_pm(struct uart_port *port, unsigned int state, unsigned char efr; dev_dbg(up->port.dev, "serial_omap_pm+%d\n", up->pdev->id); - serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB); + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); efr = serial_in(up, UART_EFR); serial_out(up, UART_EFR, efr | UART_EFR_ECB); serial_out(up, UART_LCR, 0); serial_out(up, UART_IER, (state != 0) ? UART_IERX_SLEEP : 0); - serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB); + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); serial_out(up, UART_EFR, efr); serial_out(up, UART_LCR, 0); /* Enable module level wake up */ |