aboutsummaryrefslogtreecommitdiff
path: root/drivers/power/ab8500_charger.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/power/ab8500_charger.c')
-rw-r--r--drivers/power/ab8500_charger.c1578
1 files changed, 1267 insertions, 311 deletions
diff --git a/drivers/power/ab8500_charger.c b/drivers/power/ab8500_charger.c
index 3be9c0ee3fc..19110aa613a 100644
--- a/drivers/power/ab8500_charger.c
+++ b/drivers/power/ab8500_charger.c
@@ -15,6 +15,7 @@
#include <linux/device.h>
#include <linux/interrupt.h>
#include <linux/delay.h>
+#include <linux/notifier.h>
#include <linux/slab.h>
#include <linux/platform_device.h>
#include <linux/power_supply.h>
@@ -31,6 +32,7 @@
#include <linux/mfd/abx500/ab8500-gpadc.h>
#include <linux/mfd/abx500/ux500_chargalg.h>
#include <linux/usb/otg.h>
+#include <linux/mutex.h>
/* Charger constants */
#define NO_PW_CONN 0
@@ -51,9 +53,15 @@
#define VBUS_DET_DBNC100 0x02
#define VBUS_DET_DBNC1 0x01
#define OTP_ENABLE_WD 0x01
+#define DROP_COUNT_RESET 0x01
+#define USB_CH_DET 0x01
#define MAIN_CH_INPUT_CURR_SHIFT 4
#define VBUS_IN_CURR_LIM_SHIFT 4
+#define AB8540_VBUS_IN_CURR_LIM_SHIFT 2
+#define AUTO_VBUS_IN_CURR_LIM_SHIFT 4
+#define AB8540_AUTO_VBUS_IN_CURR_MASK 0x3F
+#define VBUS_IN_CURR_LIM_RETRY_SET_TIME 30 /* seconds */
#define LED_INDICATOR_PWM_ENA 0x01
#define LED_INDICATOR_PWM_DIS 0x00
@@ -68,9 +76,16 @@
#define MAIN_CH_NOK 0x01
#define VBUS_DET 0x80
+#define MAIN_CH_STATUS2_MAINCHGDROP 0x80
+#define MAIN_CH_STATUS2_MAINCHARGERDETDBNC 0x40
+#define USB_CH_VBUSDROP 0x40
+#define USB_CH_VBUSDETDBNC 0x01
+
/* UsbLineStatus register bit masks */
#define AB8500_USB_LINK_STATUS 0x78
+#define AB8505_USB_LINK_STATUS 0xF8
#define AB8500_STD_HOST_SUSP 0x18
+#define USB_LINK_STATUS_SHIFT 3
/* Watchdog timeout constant */
#define WD_TIMER 0x30 /* 4min */
@@ -79,6 +94,21 @@
/* Lowest charger voltage is 3.39V -> 0x4E */
#define LOW_VOLT_REG 0x4E
+/* Step up/down delay in us */
+#define STEP_UDELAY 1000
+
+#define CHARGER_STATUS_POLL 10 /* in ms */
+
+#define CHG_WD_INTERVAL (60 * HZ)
+
+#define AB8500_SW_CONTROL_FALLBACK 0x03
+/* Wait for enumeration before charing in us */
+#define WAIT_ACA_RID_ENUMERATION (5 * 1000)
+/*External charger control*/
+#define AB8500_SYS_CHARGER_CONTROL_REG 0x52
+#define EXTERNAL_CHARGER_DISABLE_REG_VAL 0x03
+#define EXTERNAL_CHARGER_ENABLE_REG_VAL 0x07
+
/* UsbLineStatus register - usb types */
enum ab8500_charger_link_status {
USB_STAT_NOT_CONFIGURED,
@@ -97,6 +127,13 @@ enum ab8500_charger_link_status {
USB_STAT_HM_IDGND,
USB_STAT_RESERVED,
USB_STAT_NOT_VALID_LINK,
+ USB_STAT_PHY_EN,
+ USB_STAT_SUP_NO_IDGND_VBUS,
+ USB_STAT_SUP_IDGND_VBUS,
+ USB_STAT_CHARGER_LINE_1,
+ USB_STAT_CARKIT_1,
+ USB_STAT_CARKIT_2,
+ USB_STAT_ACA_DOCK_CHARGER,
};
enum ab8500_usb_state {
@@ -149,6 +186,7 @@ struct ab8500_charger_info {
int charger_voltage;
int cv_active;
bool wd_expired;
+ int charger_current;
};
struct ab8500_charger_event_flags {
@@ -159,19 +197,26 @@ struct ab8500_charger_event_flags {
bool usbchargernotok;
bool chgwdexp;
bool vbus_collapse;
+ bool vbus_drop_end;
};
struct ab8500_charger_usb_state {
- bool usb_changed;
int usb_current;
+ int usb_current_tmp;
enum ab8500_usb_state state;
+ enum ab8500_usb_state state_tmp;
spinlock_t usb_lock;
};
+struct ab8500_charger_max_usb_in_curr {
+ int usb_type_max;
+ int set_max;
+ int calculated_max;
+};
+
/**
* struct ab8500_charger - ab8500 Charger device information
* @dev: Pointer to the structure device
- * @max_usb_in_curr: Max USB charger input current
* @vbus_detected: VBUS detected
* @vbus_detected_start:
* VBUS detected during startup
@@ -182,36 +227,50 @@ struct ab8500_charger_usb_state {
* charger is enabled
* @vbat Battery voltage
* @old_vbat Previously measured battery voltage
+ * @usb_device_is_unrecognised USB device is unrecognised by the hardware
* @autopower Indicate if we should have automatic pwron after pwrloss
* @autopower_cfg platform specific power config support for "pwron after pwrloss"
+ * @invalid_charger_detect_state State when forcing AB to use invalid charger
+ * @is_aca_rid: Incicate if accessory is ACA type
+ * @current_stepping_sessions:
+ * Counter for current stepping sessions
* @parent: Pointer to the struct ab8500
* @gpadc: Pointer to the struct gpadc
- * @bat: Pointer to the abx500_bm platform data
+ * @bm: Platform specific battery management information
* @flags: Structure for information about events triggered
* @usb_state: Structure for usb stack information
+ * @max_usb_in_curr: Max USB charger input current
* @ac_chg: AC charger power supply
* @usb_chg: USB charger power supply
* @ac: Structure that holds the AC charger properties
* @usb: Structure that holds the USB charger properties
* @regu: Pointer to the struct regulator
* @charger_wq: Work queue for the IRQs and checking HW state
+ * @usb_ipt_crnt_lock: Lock to protect VBUS input current setting from mutuals
+ * @pm_lock: Lock to prevent system to suspend
* @check_vbat_work Work for checking vbat threshold to adjust vbus current
* @check_hw_failure_work: Work for checking HW state
* @check_usbchgnotok_work: Work for checking USB charger not ok status
* @kick_wd_work: Work for kicking the charger watchdog in case
* of ABB rev 1.* due to the watchog logic bug
+ * @ac_charger_attached_work: Work for checking if AC charger is still
+ * connected
+ * @usb_charger_attached_work: Work for checking if USB charger is still
+ * connected
* @ac_work: Work for checking AC charger connection
* @detect_usb_type_work: Work for detecting the USB type connected
* @usb_link_status_work: Work for checking the new USB link status
* @usb_state_changed_work: Work for checking USB state
+ * @attach_work: Work for detecting USB type
+ * @vbus_drop_end_work: Work for detecting VBUS drop end
* @check_main_thermal_prot_work:
* Work for checking Main thermal status
* @check_usb_thermal_prot_work:
* Work for checking USB thermal status
+ * @charger_attached_mutex: For controlling the wakelock
*/
struct ab8500_charger {
struct device *dev;
- int max_usb_in_curr;
bool vbus_detected;
bool vbus_detected_start;
bool ac_conn;
@@ -219,31 +278,42 @@ struct ab8500_charger {
bool vddadc_en_usb;
int vbat;
int old_vbat;
+ bool usb_device_is_unrecognised;
bool autopower;
bool autopower_cfg;
+ int invalid_charger_detect_state;
+ int is_aca_rid;
+ atomic_t current_stepping_sessions;
struct ab8500 *parent;
struct ab8500_gpadc *gpadc;
- struct abx500_bm_data *bat;
+ struct abx500_bm_data *bm;
struct ab8500_charger_event_flags flags;
struct ab8500_charger_usb_state usb_state;
+ struct ab8500_charger_max_usb_in_curr max_usb_in_curr;
struct ux500_charger ac_chg;
struct ux500_charger usb_chg;
struct ab8500_charger_info ac;
struct ab8500_charger_info usb;
struct regulator *regu;
struct workqueue_struct *charger_wq;
+ struct mutex usb_ipt_crnt_lock;
struct delayed_work check_vbat_work;
struct delayed_work check_hw_failure_work;
struct delayed_work check_usbchgnotok_work;
struct delayed_work kick_wd_work;
+ struct delayed_work usb_state_changed_work;
+ struct delayed_work attach_work;
+ struct delayed_work ac_charger_attached_work;
+ struct delayed_work usb_charger_attached_work;
+ struct delayed_work vbus_drop_end_work;
struct work_struct ac_work;
struct work_struct detect_usb_type_work;
struct work_struct usb_link_status_work;
- struct work_struct usb_state_changed_work;
struct work_struct check_main_thermal_prot_work;
struct work_struct check_usb_thermal_prot_work;
struct usb_phy *usb_phy;
struct notifier_block nb;
+ struct mutex charger_attached_mutex;
};
/* AC properties */
@@ -267,50 +337,65 @@ static enum power_supply_property ab8500_charger_usb_props[] = {
POWER_SUPPLY_PROP_CURRENT_NOW,
};
-/**
- * ab8500_power_loss_handling - set how we handle powerloss.
- * @di: pointer to the ab8500_charger structure
- *
- * Magic nummbers are from STE HW department.
+/*
+ * Function for enabling and disabling sw fallback mode
+ * should always be disabled when no charger is connected.
*/
-static void ab8500_power_loss_handling(struct ab8500_charger *di)
+static void ab8500_enable_disable_sw_fallback(struct ab8500_charger *di,
+ bool fallback)
{
+ u8 val;
u8 reg;
+ u8 bank;
+ u8 bit;
int ret;
- dev_dbg(di->dev, "Autopower : %d\n", di->autopower);
+ dev_dbg(di->dev, "SW Fallback: %d\n", fallback);
- /* read the autopower register */
- ret = abx500_get_register_interruptible(di->dev, 0x15, 0x00, &reg);
- if (ret) {
- dev_err(di->dev, "%d write failed\n", __LINE__);
- return;
+ if (is_ab8500(di->parent)) {
+ bank = 0x15;
+ reg = 0x0;
+ bit = 3;
+ } else {
+ bank = AB8500_SYS_CTRL1_BLOCK;
+ reg = AB8500_SW_CONTROL_FALLBACK;
+ bit = 0;
}
- /* enable the OPT emulation registers */
- ret = abx500_set_register_interruptible(di->dev, 0x11, 0x00, 0x2);
- if (ret) {
- dev_err(di->dev, "%d write failed\n", __LINE__);
+ /* read the register containing fallback bit */
+ ret = abx500_get_register_interruptible(di->dev, bank, reg, &val);
+ if (ret < 0) {
+ dev_err(di->dev, "%d read failed\n", __LINE__);
return;
}
- if (di->autopower)
- reg |= 0x8;
+ if (is_ab8500(di->parent)) {
+ /* enable the OPT emulation registers */
+ ret = abx500_set_register_interruptible(di->dev, 0x11, 0x00, 0x2);
+ if (ret) {
+ dev_err(di->dev, "%d write failed\n", __LINE__);
+ goto disable_otp;
+ }
+ }
+
+ if (fallback)
+ val |= (1 << bit);
else
- reg &= ~0x8;
+ val &= ~(1 << bit);
- /* write back the changed value to autopower reg */
- ret = abx500_set_register_interruptible(di->dev, 0x15, 0x00, reg);
+ /* write back the changed fallback bit value to register */
+ ret = abx500_set_register_interruptible(di->dev, bank, reg, val);
if (ret) {
dev_err(di->dev, "%d write failed\n", __LINE__);
- return;
}
- /* disable the set OTP registers again */
- ret = abx500_set_register_interruptible(di->dev, 0x11, 0x00, 0x0);
- if (ret) {
- dev_err(di->dev, "%d write failed\n", __LINE__);
- return;
+disable_otp:
+ if (is_ab8500(di->parent)) {
+ /* disable the set OTP registers again */
+ ret = abx500_set_register_interruptible(di->dev, 0x11, 0x00, 0x0);
+ if (ret) {
+ dev_err(di->dev, "%d write failed\n", __LINE__);
+ }
}
}
@@ -329,12 +414,12 @@ static void ab8500_power_supply_changed(struct ab8500_charger *di,
!di->ac.charger_connected &&
di->autopower) {
di->autopower = false;
- ab8500_power_loss_handling(di);
+ ab8500_enable_disable_sw_fallback(di, false);
} else if (!di->autopower &&
(di->ac.charger_connected ||
di->usb.charger_connected)) {
di->autopower = true;
- ab8500_power_loss_handling(di);
+ ab8500_enable_disable_sw_fallback(di, true);
}
}
power_supply_changed(psy);
@@ -346,7 +431,25 @@ static void ab8500_charger_set_usb_connected(struct ab8500_charger *di,
if (connected != di->usb.charger_connected) {
dev_dbg(di->dev, "USB connected:%i\n", connected);
di->usb.charger_connected = connected;
+
+ if (!connected)
+ di->flags.vbus_drop_end = false;
+
sysfs_notify(&di->usb_chg.psy.dev->kobj, NULL, "present");
+
+ if (connected) {
+ mutex_lock(&di->charger_attached_mutex);
+ mutex_unlock(&di->charger_attached_mutex);
+
+ if (is_ab8500(di->parent))
+ queue_delayed_work(di->charger_wq,
+ &di->usb_charger_attached_work,
+ HZ);
+ } else {
+ cancel_delayed_work_sync(&di->usb_charger_attached_work);
+ mutex_lock(&di->charger_attached_mutex);
+ mutex_unlock(&di->charger_attached_mutex);
+ }
}
}
@@ -500,6 +603,7 @@ static int ab8500_charger_usb_cv(struct ab8500_charger *di)
/**
* ab8500_charger_detect_chargers() - Detect the connected chargers
* @di: pointer to the ab8500_charger structure
+ * @probe: if probe, don't delay and wait for HW
*
* Returns the type of charger connected.
* For USB it will not mean we can actually charge from it
@@ -513,7 +617,7 @@ static int ab8500_charger_usb_cv(struct ab8500_charger *di)
* USB_PW_CONN if the USB power supply is connected
* AC_PW_CONN + USB_PW_CONN if USB and AC power supplies are both connected
*/
-static int ab8500_charger_detect_chargers(struct ab8500_charger *di)
+static int ab8500_charger_detect_chargers(struct ab8500_charger *di, bool probe)
{
int result = NO_PW_CONN;
int ret;
@@ -531,13 +635,25 @@ static int ab8500_charger_detect_chargers(struct ab8500_charger *di)
result = AC_PW_CONN;
/* Check for USB charger */
+
+ if (!probe) {
+ /*
+ * AB8500 says VBUS_DET_DBNC1 & VBUS_DET_DBNC100
+ * when disconnecting ACA even though no
+ * charger was connected. Try waiting a little
+ * longer than the 100 ms of VBUS_DET_DBNC100...
+ */
+ msleep(110);
+ }
ret = abx500_get_register_interruptible(di->dev, AB8500_CHARGER,
AB8500_CH_USBCH_STAT1_REG, &val);
if (ret < 0) {
dev_err(di->dev, "%s ab8500 read failed\n", __func__);
return ret;
}
-
+ dev_dbg(di->dev,
+ "%s AB8500_CH_USBCH_STAT1_REG %x\n", __func__,
+ val);
if ((val & VBUS_DET_DBNC1) && (val & VBUS_DET_DBNC100))
result |= USB_PW_CONN;
@@ -554,75 +670,125 @@ static int ab8500_charger_detect_chargers(struct ab8500_charger *di)
* Returns error code in case of failure else 0 on success
*/
static int ab8500_charger_max_usb_curr(struct ab8500_charger *di,
- enum ab8500_charger_link_status link_status)
+ enum ab8500_charger_link_status link_status)
{
int ret = 0;
+ di->usb_device_is_unrecognised = false;
+
+ /*
+ * Platform only supports USB 2.0.
+ * This means that charging current from USB source
+ * is maximum 500 mA. Every occurence of USB_STAT_*_HOST_*
+ * should set USB_CH_IP_CUR_LVL_0P5.
+ */
+
switch (link_status) {
case USB_STAT_STD_HOST_NC:
case USB_STAT_STD_HOST_C_NS:
case USB_STAT_STD_HOST_C_S:
dev_dbg(di->dev, "USB Type - Standard host is "
"detected through USB driver\n");
- di->max_usb_in_curr = USB_CH_IP_CUR_LVL_0P09;
+ di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_0P5;
+ di->is_aca_rid = 0;
break;
case USB_STAT_HOST_CHG_HS_CHIRP:
- di->max_usb_in_curr = USB_CH_IP_CUR_LVL_0P5;
+ di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_0P5;
+ di->is_aca_rid = 0;
break;
case USB_STAT_HOST_CHG_HS:
+ di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_0P5;
+ di->is_aca_rid = 0;
+ break;
case USB_STAT_ACA_RID_C_HS:
- di->max_usb_in_curr = USB_CH_IP_CUR_LVL_0P9;
+ di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_0P9;
+ di->is_aca_rid = 0;
break;
case USB_STAT_ACA_RID_A:
/*
* Dedicated charger level minus maximum current accessory
- * can consume (300mA). Closest level is 1100mA
+ * can consume (900mA). Closest level is 500mA
*/
- di->max_usb_in_curr = USB_CH_IP_CUR_LVL_1P1;
+ dev_dbg(di->dev, "USB_STAT_ACA_RID_A detected\n");
+ di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_0P5;
+ di->is_aca_rid = 1;
break;
case USB_STAT_ACA_RID_B:
/*
* Dedicated charger level minus 120mA (20mA for ACA and
* 100mA for potential accessory). Closest level is 1300mA
*/
- di->max_usb_in_curr = USB_CH_IP_CUR_LVL_1P3;
+ di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_1P3;
+ dev_dbg(di->dev, "USB Type - 0x%02x MaxCurr: %d", link_status,
+ di->max_usb_in_curr.usb_type_max);
+ di->is_aca_rid = 1;
break;
- case USB_STAT_DEDICATED_CHG:
case USB_STAT_HOST_CHG_NM:
+ di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_0P5;
+ di->is_aca_rid = 0;
+ break;
+ case USB_STAT_DEDICATED_CHG:
+ di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_1P5;
+ di->is_aca_rid = 0;
+ break;
case USB_STAT_ACA_RID_C_HS_CHIRP:
case USB_STAT_ACA_RID_C_NM:
- di->max_usb_in_curr = USB_CH_IP_CUR_LVL_1P5;
+ di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_1P5;
+ di->is_aca_rid = 1;
break;
- case USB_STAT_RESERVED:
- /*
- * This state is used to indicate that VBUS has dropped below
- * the detection level 4 times in a row. This is due to the
- * charger output current is set to high making the charger
- * voltage collapse. This have to be propagated through to
- * chargalg. This is done using the property
- * POWER_SUPPLY_PROP_CURRENT_AVG = 1
- */
- di->flags.vbus_collapse = true;
- dev_dbg(di->dev, "USB Type - USB_STAT_RESERVED "
- "VBUS has collapsed\n");
- ret = -1;
- break;
- case USB_STAT_HM_IDGND:
case USB_STAT_NOT_CONFIGURED:
- case USB_STAT_NOT_VALID_LINK:
+ if (di->vbus_detected) {
+ di->usb_device_is_unrecognised = true;
+ dev_dbg(di->dev, "USB Type - Legacy charger.\n");
+ di->max_usb_in_curr.usb_type_max =
+ USB_CH_IP_CUR_LVL_1P5;
+ break;
+ }
+ case USB_STAT_HM_IDGND:
dev_err(di->dev, "USB Type - Charging not allowed\n");
- di->max_usb_in_curr = USB_CH_IP_CUR_LVL_0P05;
+ di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_0P05;
ret = -ENXIO;
break;
+ case USB_STAT_RESERVED:
+ if (is_ab8500(di->parent)) {
+ di->flags.vbus_collapse = true;
+ dev_err(di->dev, "USB Type - USB_STAT_RESERVED "
+ "VBUS has collapsed\n");
+ ret = -ENXIO;
+ break;
+ } else {
+ dev_dbg(di->dev, "USB Type - Charging not allowed\n");
+ di->max_usb_in_curr.usb_type_max =
+ USB_CH_IP_CUR_LVL_0P05;
+ dev_dbg(di->dev, "USB Type - 0x%02x MaxCurr: %d",
+ link_status,
+ di->max_usb_in_curr.usb_type_max);
+ ret = -ENXIO;
+ break;
+ }
+ case USB_STAT_CARKIT_1:
+ case USB_STAT_CARKIT_2:
+ case USB_STAT_ACA_DOCK_CHARGER:
+ case USB_STAT_CHARGER_LINE_1:
+ di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_0P5;
+ dev_dbg(di->dev, "USB Type - 0x%02x MaxCurr: %d", link_status,
+ di->max_usb_in_curr.usb_type_max);
+ break;
+ case USB_STAT_NOT_VALID_LINK:
+ dev_err(di->dev, "USB Type invalid - try charging anyway\n");
+ di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_0P5;
+ break;
+
default:
dev_err(di->dev, "USB Type - Unknown\n");
- di->max_usb_in_curr = USB_CH_IP_CUR_LVL_0P05;
+ di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_0P05;
ret = -ENXIO;
break;
};
+ di->max_usb_in_curr.set_max = di->max_usb_in_curr.usb_type_max;
dev_dbg(di->dev, "USB Type - 0x%02x MaxCurr: %d",
- link_status, di->max_usb_in_curr);
+ link_status, di->max_usb_in_curr.set_max);
return ret;
}
@@ -645,15 +811,22 @@ static int ab8500_charger_read_usb_type(struct ab8500_charger *di)
dev_err(di->dev, "%s ab8500 read failed\n", __func__);
return ret;
}
- ret = abx500_get_register_interruptible(di->dev, AB8500_USB,
- AB8500_USB_LINE_STAT_REG, &val);
+ if (is_ab8500(di->parent))
+ ret = abx500_get_register_interruptible(di->dev, AB8500_USB,
+ AB8500_USB_LINE_STAT_REG, &val);
+ else
+ ret = abx500_get_register_interruptible(di->dev,
+ AB8500_USB, AB8500_USB_LINK1_STAT_REG, &val);
if (ret < 0) {
dev_err(di->dev, "%s ab8500 read failed\n", __func__);
return ret;
}
/* get the USB type */
- val = (val & AB8500_USB_LINK_STATUS) >> 3;
+ if (is_ab8500(di->parent))
+ val = (val & AB8500_USB_LINK_STATUS) >> USB_LINK_STATUS_SHIFT;
+ else
+ val = (val & AB8505_USB_LINK_STATUS) >> USB_LINK_STATUS_SHIFT;
ret = ab8500_charger_max_usb_curr(di,
(enum ab8500_charger_link_status) val);
@@ -682,16 +855,25 @@ static int ab8500_charger_detect_usb_type(struct ab8500_charger *di)
ret = abx500_get_register_interruptible(di->dev,
AB8500_INTERRUPT, AB8500_IT_SOURCE21_REG,
&val);
+ dev_dbg(di->dev, "%s AB8500_IT_SOURCE21_REG %x\n",
+ __func__, val);
if (ret < 0) {
dev_err(di->dev, "%s ab8500 read failed\n", __func__);
return ret;
}
- ret = abx500_get_register_interruptible(di->dev, AB8500_USB,
- AB8500_USB_LINE_STAT_REG, &val);
+
+ if (is_ab8500(di->parent))
+ ret = abx500_get_register_interruptible(di->dev,
+ AB8500_USB, AB8500_USB_LINE_STAT_REG, &val);
+ else
+ ret = abx500_get_register_interruptible(di->dev,
+ AB8500_USB, AB8500_USB_LINK1_STAT_REG, &val);
if (ret < 0) {
dev_err(di->dev, "%s ab8500 read failed\n", __func__);
return ret;
}
+ dev_dbg(di->dev, "%s AB8500_USB_LINE_STAT_REG %x\n", __func__,
+ val);
/*
* Until the IT source register is read the UsbLineStatus
* register is not updated, hence doing the same
@@ -699,7 +881,12 @@ static int ab8500_charger_detect_usb_type(struct ab8500_charger *di)
*/
/* get the USB type */
- val = (val & AB8500_USB_LINK_STATUS) >> 3;
+ if (is_ab8500(di->parent))
+ val = (val & AB8500_USB_LINK_STATUS) >>
+ USB_LINK_STATUS_SHIFT;
+ else
+ val = (val & AB8505_USB_LINK_STATUS) >>
+ USB_LINK_STATUS_SHIFT;
if (val)
break;
}
@@ -794,51 +981,6 @@ static int ab8500_charger_voltage_map[] = {
4600 ,
};
-/*
- * This array maps the raw hex value to charger current used by the AB8500
- * Values taken from the UM0836
- */
-static int ab8500_charger_current_map[] = {
- 100 ,
- 200 ,
- 300 ,
- 400 ,
- 500 ,
- 600 ,
- 700 ,
- 800 ,
- 900 ,
- 1000 ,
- 1100 ,
- 1200 ,
- 1300 ,
- 1400 ,
- 1500 ,
-};
-
-/*
- * This array maps the raw hex value to VBUS input current used by the AB8500
- * Values taken from the UM0836
- */
-static int ab8500_charger_vbus_in_curr_map[] = {
- USB_CH_IP_CUR_LVL_0P05,
- USB_CH_IP_CUR_LVL_0P09,
- USB_CH_IP_CUR_LVL_0P19,
- USB_CH_IP_CUR_LVL_0P29,
- USB_CH_IP_CUR_LVL_0P38,
- USB_CH_IP_CUR_LVL_0P45,
- USB_CH_IP_CUR_LVL_0P5,
- USB_CH_IP_CUR_LVL_0P6,
- USB_CH_IP_CUR_LVL_0P7,
- USB_CH_IP_CUR_LVL_0P8,
- USB_CH_IP_CUR_LVL_0P9,
- USB_CH_IP_CUR_LVL_1P0,
- USB_CH_IP_CUR_LVL_1P1,
- USB_CH_IP_CUR_LVL_1P3,
- USB_CH_IP_CUR_LVL_1P4,
- USB_CH_IP_CUR_LVL_1P5,
-};
-
static int ab8500_voltage_to_regval(int voltage)
{
int i;
@@ -860,41 +1002,41 @@ static int ab8500_voltage_to_regval(int voltage)
return -1;
}
-static int ab8500_current_to_regval(int curr)
+static int ab8500_current_to_regval(struct ab8500_charger *di, int curr)
{
int i;
- if (curr < ab8500_charger_current_map[0])
+ if (curr < di->bm->chg_output_curr[0])
return 0;
- for (i = 0; i < ARRAY_SIZE(ab8500_charger_current_map); i++) {
- if (curr < ab8500_charger_current_map[i])
+ for (i = 0; i < di->bm->n_chg_out_curr; i++) {
+ if (curr < di->bm->chg_output_curr[i])
return i - 1;
}
/* If not last element, return error */
- i = ARRAY_SIZE(ab8500_charger_current_map) - 1;
- if (curr == ab8500_charger_current_map[i])
+ i = di->bm->n_chg_out_curr - 1;
+ if (curr == di->bm->chg_output_curr[i])
return i;
else
return -1;
}
-static int ab8500_vbus_in_curr_to_regval(int curr)
+static int ab8500_vbus_in_curr_to_regval(struct ab8500_charger *di, int curr)
{
int i;
- if (curr < ab8500_charger_vbus_in_curr_map[0])
+ if (curr < di->bm->chg_input_curr[0])
return 0;
- for (i = 0; i < ARRAY_SIZE(ab8500_charger_vbus_in_curr_map); i++) {
- if (curr < ab8500_charger_vbus_in_curr_map[i])
+ for (i = 0; i < di->bm->n_chg_in_curr; i++) {
+ if (curr < di->bm->chg_input_curr[i])
return i - 1;
}
/* If not last element, return error */
- i = ARRAY_SIZE(ab8500_charger_vbus_in_curr_map) - 1;
- if (curr == ab8500_charger_vbus_in_curr_map[i])
+ i = di->bm->n_chg_in_curr - 1;
+ if (curr == di->bm->chg_input_curr[i])
return i;
else
return -1;
@@ -911,28 +1053,177 @@ static int ab8500_vbus_in_curr_to_regval(int curr)
*/
static int ab8500_charger_get_usb_cur(struct ab8500_charger *di)
{
+ int ret = 0;
switch (di->usb_state.usb_current) {
case 100:
- di->max_usb_in_curr = USB_CH_IP_CUR_LVL_0P09;
+ di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_0P09;
break;
case 200:
- di->max_usb_in_curr = USB_CH_IP_CUR_LVL_0P19;
+ di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_0P19;
break;
case 300:
- di->max_usb_in_curr = USB_CH_IP_CUR_LVL_0P29;
+ di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_0P29;
break;
case 400:
- di->max_usb_in_curr = USB_CH_IP_CUR_LVL_0P38;
+ di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_0P38;
break;
case 500:
- di->max_usb_in_curr = USB_CH_IP_CUR_LVL_0P5;
+ di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_0P5;
break;
default:
- di->max_usb_in_curr = USB_CH_IP_CUR_LVL_0P05;
- return -1;
+ di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_0P05;
+ ret = -EPERM;
break;
};
- return 0;
+ di->max_usb_in_curr.set_max = di->max_usb_in_curr.usb_type_max;
+ return ret;
+}
+
+/**
+ * ab8500_charger_check_continue_stepping() - Check to allow stepping
+ * @di: pointer to the ab8500_charger structure
+ * @reg: select what charger register to check
+ *
+ * Check if current stepping should be allowed to continue.
+ * Checks if charger source has not collapsed. If it has, further stepping
+ * is not allowed.
+ */
+static bool ab8500_charger_check_continue_stepping(struct ab8500_charger *di,
+ int reg)
+{
+ if (reg == AB8500_USBCH_IPT_CRNTLVL_REG)
+ return !di->flags.vbus_drop_end;
+ else
+ return true;
+}
+
+/**
+ * ab8500_charger_set_current() - set charger current
+ * @di: pointer to the ab8500_charger structure
+ * @ich: charger current, in mA
+ * @reg: select what charger register to set
+ *
+ * Set charger current.
+ * There is no state machine in the AB to step up/down the charger
+ * current to avoid dips and spikes on MAIN, VBUS and VBAT when
+ * charging is started. Instead we need to implement
+ * this charger current step-up/down here.
+ * Returns error code in case of failure else 0(on success)
+ */
+static int ab8500_charger_set_current(struct ab8500_charger *di,
+ int ich, int reg)
+{
+ int ret = 0;
+ int curr_index, prev_curr_index, shift_value, i;
+ u8 reg_value;
+ u32 step_udelay;
+ bool no_stepping = false;
+
+ atomic_inc(&di->current_stepping_sessions);
+
+ ret = abx500_get_register_interruptible(di->dev, AB8500_CHARGER,
+ reg, &reg_value);
+ if (ret < 0) {
+ dev_err(di->dev, "%s read failed\n", __func__);
+ goto exit_set_current;
+ }
+
+ switch (reg) {
+ case AB8500_MCH_IPT_CURLVL_REG:
+ shift_value = MAIN_CH_INPUT_CURR_SHIFT;
+ prev_curr_index = (reg_value >> shift_value);
+ curr_index = ab8500_current_to_regval(di, ich);
+ step_udelay = STEP_UDELAY;
+ if (!di->ac.charger_connected)
+ no_stepping = true;
+ break;
+ case AB8500_USBCH_IPT_CRNTLVL_REG:
+ if (is_ab8540(di->parent))
+ shift_value = AB8540_VBUS_IN_CURR_LIM_SHIFT;
+ else
+ shift_value = VBUS_IN_CURR_LIM_SHIFT;
+ prev_curr_index = (reg_value >> shift_value);
+ curr_index = ab8500_vbus_in_curr_to_regval(di, ich);
+ step_udelay = STEP_UDELAY * 100;
+
+ if (!di->usb.charger_connected)
+ no_stepping = true;
+ break;
+ case AB8500_CH_OPT_CRNTLVL_REG:
+ shift_value = 0;
+ prev_curr_index = (reg_value >> shift_value);
+ curr_index = ab8500_current_to_regval(di, ich);
+ step_udelay = STEP_UDELAY;
+ if (curr_index && (curr_index - prev_curr_index) > 1)
+ step_udelay *= 100;
+
+ if (!di->usb.charger_connected && !di->ac.charger_connected)
+ no_stepping = true;
+
+ break;
+ default:
+ dev_err(di->dev, "%s current register not valid\n", __func__);
+ ret = -ENXIO;
+ goto exit_set_current;
+ }
+
+ if (curr_index < 0) {
+ dev_err(di->dev, "requested current limit out-of-range\n");
+ ret = -ENXIO;
+ goto exit_set_current;
+ }
+
+ /* only update current if it's been changed */
+ if (prev_curr_index == curr_index) {
+ dev_dbg(di->dev, "%s current not changed for reg: 0x%02x\n",
+ __func__, reg);
+ ret = 0;
+ goto exit_set_current;
+ }
+
+ dev_dbg(di->dev, "%s set charger current: %d mA for reg: 0x%02x\n",
+ __func__, ich, reg);
+
+ if (no_stepping) {
+ ret = abx500_set_register_interruptible(di->dev, AB8500_CHARGER,
+ reg, (u8)curr_index << shift_value);
+ if (ret)
+ dev_err(di->dev, "%s write failed\n", __func__);
+ } else if (prev_curr_index > curr_index) {
+ for (i = prev_curr_index - 1; i >= curr_index; i--) {
+ dev_dbg(di->dev, "curr change_1 to: %x for 0x%02x\n",
+ (u8) i << shift_value, reg);
+ ret = abx500_set_register_interruptible(di->dev,
+ AB8500_CHARGER, reg, (u8)i << shift_value);
+ if (ret) {
+ dev_err(di->dev, "%s write failed\n", __func__);
+ goto exit_set_current;
+ }
+ if (i != curr_index)
+ usleep_range(step_udelay, step_udelay * 2);
+ }
+ } else {
+ bool allow = true;
+ for (i = prev_curr_index + 1; i <= curr_index && allow; i++) {
+ dev_dbg(di->dev, "curr change_2 to: %x for 0x%02x\n",
+ (u8)i << shift_value, reg);
+ ret = abx500_set_register_interruptible(di->dev,
+ AB8500_CHARGER, reg, (u8)i << shift_value);
+ if (ret) {
+ dev_err(di->dev, "%s write failed\n", __func__);
+ goto exit_set_current;
+ }
+ if (i != curr_index)
+ usleep_range(step_udelay, step_udelay * 2);
+
+ allow = ab8500_charger_check_continue_stepping(di, reg);
+ }
+ }
+
+exit_set_current:
+ atomic_dec(&di->current_stepping_sessions);
+
+ return ret;
}
/**
@@ -946,12 +1237,16 @@ static int ab8500_charger_get_usb_cur(struct ab8500_charger *di)
static int ab8500_charger_set_vbus_in_curr(struct ab8500_charger *di,
int ich_in)
{
- int ret;
- int input_curr_index;
int min_value;
+ int ret;
/* We should always use to lowest current limit */
- min_value = min(di->bat->chg_params->usb_curr_max, ich_in);
+ min_value = min(di->bm->chg_params->usb_curr_max, ich_in);
+ if (di->max_usb_in_curr.set_max > 0)
+ min_value = min(di->max_usb_in_curr.set_max, min_value);
+
+ if (di->usb_state.usb_current >= 0)
+ min_value = min(di->usb_state.usb_current, min_value);
switch (min_value) {
case 100:
@@ -966,22 +1261,47 @@ static int ab8500_charger_set_vbus_in_curr(struct ab8500_charger *di,
break;
}
- input_curr_index = ab8500_vbus_in_curr_to_regval(min_value);
- if (input_curr_index < 0) {
- dev_err(di->dev, "VBUS input current limit too high\n");
- return -ENXIO;
- }
+ dev_info(di->dev, "VBUS input current limit set to %d mA\n", min_value);
- ret = abx500_set_register_interruptible(di->dev, AB8500_CHARGER,
- AB8500_USBCH_IPT_CRNTLVL_REG,
- input_curr_index << VBUS_IN_CURR_LIM_SHIFT);
- if (ret)
- dev_err(di->dev, "%s write failed\n", __func__);
+ mutex_lock(&di->usb_ipt_crnt_lock);
+ ret = ab8500_charger_set_current(di, min_value,
+ AB8500_USBCH_IPT_CRNTLVL_REG);
+ mutex_unlock(&di->usb_ipt_crnt_lock);
return ret;
}
/**
+ * ab8500_charger_set_main_in_curr() - set main charger input current
+ * @di: pointer to the ab8500_charger structure
+ * @ich_in: input charger current, in mA
+ *
+ * Set main charger input current.
+ * Returns error code in case of failure else 0(on success)
+ */
+static int ab8500_charger_set_main_in_curr(struct ab8500_charger *di,
+ int ich_in)
+{
+ return ab8500_charger_set_current(di, ich_in,
+ AB8500_MCH_IPT_CURLVL_REG);
+}
+
+/**
+ * ab8500_charger_set_output_curr() - set charger output current
+ * @di: pointer to the ab8500_charger structure
+ * @ich_out: output charger current, in mA
+ *
+ * Set charger output current.
+ * Returns error code in case of failure else 0(on success)
+ */
+static int ab8500_charger_set_output_curr(struct ab8500_charger *di,
+ int ich_out)
+{
+ return ab8500_charger_set_current(di, ich_out,
+ AB8500_CH_OPT_CRNTLVL_REG);
+}
+
+/**
* ab8500_charger_led_en() - turn on/off chargign led
* @di: pointer to the ab8500_charger structure
* @on: flag to turn on/off the chargign led
@@ -1066,15 +1386,19 @@ static int ab8500_charger_ac_en(struct ux500_charger *charger,
* the GPADC module independant of the AB8500 chargers
*/
if (!di->vddadc_en_ac) {
- regulator_enable(di->regu);
- di->vddadc_en_ac = true;
+ ret = regulator_enable(di->regu);
+ if (ret)
+ dev_warn(di->dev,
+ "Failed to enable regulator\n");
+ else
+ di->vddadc_en_ac = true;
}
/* Check if the requested voltage or current is valid */
volt_index = ab8500_voltage_to_regval(vset);
- curr_index = ab8500_current_to_regval(iset);
- input_curr_index = ab8500_current_to_regval(
- di->bat->chg_params->ac_curr_max);
+ curr_index = ab8500_current_to_regval(di, iset);
+ input_curr_index = ab8500_current_to_regval(di,
+ di->bm->chg_params->ac_curr_max);
if (volt_index < 0 || curr_index < 0 || input_curr_index < 0) {
dev_err(di->dev,
"Charger voltage or current too high, "
@@ -1090,23 +1414,24 @@ static int ab8500_charger_ac_en(struct ux500_charger *charger,
return ret;
}
/* MainChInputCurr: current that can be drawn from the charger*/
- ret = abx500_set_register_interruptible(di->dev, AB8500_CHARGER,
- AB8500_MCH_IPT_CURLVL_REG,
- input_curr_index << MAIN_CH_INPUT_CURR_SHIFT);
+ ret = ab8500_charger_set_main_in_curr(di,
+ di->bm->chg_params->ac_curr_max);
if (ret) {
- dev_err(di->dev, "%s write failed\n", __func__);
+ dev_err(di->dev, "%s Failed to set MainChInputCurr\n",
+ __func__);
return ret;
}
/* ChOutputCurentLevel: protected output current */
- ret = abx500_set_register_interruptible(di->dev, AB8500_CHARGER,
- AB8500_CH_OPT_CRNTLVL_REG, (u8) curr_index);
+ ret = ab8500_charger_set_output_curr(di, iset);
if (ret) {
- dev_err(di->dev, "%s write failed\n", __func__);
+ dev_err(di->dev, "%s "
+ "Failed to set ChOutputCurentLevel\n",
+ __func__);
return ret;
}
/* Check if VBAT overshoot control should be enabled */
- if (!di->bat->enable_overshoot)
+ if (!di->bm->enable_overshoot)
overshoot = MAIN_CH_NO_OVERSHOOT_ENA_N;
/* Enable Main Charger */
@@ -1158,12 +1483,11 @@ static int ab8500_charger_ac_en(struct ux500_charger *charger,
return ret;
}
- ret = abx500_set_register_interruptible(di->dev,
- AB8500_CHARGER,
- AB8500_CH_OPT_CRNTLVL_REG, CH_OP_CUR_LVL_0P1);
+ ret = ab8500_charger_set_output_curr(di, 0);
if (ret) {
- dev_err(di->dev,
- "%s write failed\n", __func__);
+ dev_err(di->dev, "%s "
+ "Failed to set ChOutputCurentLevel\n",
+ __func__);
return ret;
}
} else {
@@ -1235,8 +1559,12 @@ static int ab8500_charger_usb_en(struct ux500_charger *charger,
* the GPADC module independant of the AB8500 chargers
*/
if (!di->vddadc_en_usb) {
- regulator_enable(di->regu);
- di->vddadc_en_usb = true;
+ ret = regulator_enable(di->regu);
+ if (ret)
+ dev_warn(di->dev,
+ "Failed to enable regulator\n");
+ else
+ di->vddadc_en_usb = true;
}
/* Enable USB charging */
@@ -1244,7 +1572,7 @@ static int ab8500_charger_usb_en(struct ux500_charger *charger,
/* Check if the requested voltage or current is valid */
volt_index = ab8500_voltage_to_regval(vset);
- curr_index = ab8500_current_to_regval(ich_out);
+ curr_index = ab8500_current_to_regval(di, ich_out);
if (volt_index < 0 || curr_index < 0) {
dev_err(di->dev,
"Charger voltage or current too high, "
@@ -1259,24 +1587,13 @@ static int ab8500_charger_usb_en(struct ux500_charger *charger,
dev_err(di->dev, "%s write failed\n", __func__);
return ret;
}
- /* USBChInputCurr: current that can be drawn from the usb */
- ret = ab8500_charger_set_vbus_in_curr(di, di->max_usb_in_curr);
- if (ret) {
- dev_err(di->dev, "setting USBChInputCurr failed\n");
- return ret;
- }
- /* ChOutputCurentLevel: protected output current */
- ret = abx500_set_register_interruptible(di->dev, AB8500_CHARGER,
- AB8500_CH_OPT_CRNTLVL_REG, (u8) curr_index);
- if (ret) {
- dev_err(di->dev, "%s write failed\n", __func__);
- return ret;
- }
/* Check if VBAT overshoot control should be enabled */
- if (!di->bat->enable_overshoot)
+ if (!di->bm->enable_overshoot)
overshoot = USB_CHG_NO_OVERSHOOT_ENA_N;
/* Enable USB Charger */
+ dev_dbg(di->dev,
+ "Enabling USB with write to AB8500_USBCH_CTRL1_REG\n");
ret = abx500_set_register_interruptible(di->dev, AB8500_CHARGER,
AB8500_USBCH_CTRL1_REG, USB_CH_ENA | overshoot);
if (ret) {
@@ -1289,11 +1606,30 @@ static int ab8500_charger_usb_en(struct ux500_charger *charger,
if (ret < 0)
dev_err(di->dev, "failed to enable LED\n");
+ di->usb.charger_online = 1;
+
+ /* USBChInputCurr: current that can be drawn from the usb */
+ ret = ab8500_charger_set_vbus_in_curr(di,
+ di->max_usb_in_curr.usb_type_max);
+ if (ret) {
+ dev_err(di->dev, "setting USBChInputCurr failed\n");
+ return ret;
+ }
+
+ /* ChOutputCurentLevel: protected output current */
+ ret = ab8500_charger_set_output_curr(di, ich_out);
+ if (ret) {
+ dev_err(di->dev, "%s "
+ "Failed to set ChOutputCurentLevel\n",
+ __func__);
+ return ret;
+ }
+
queue_delayed_work(di->charger_wq, &di->check_vbat_work, HZ);
- di->usb.charger_online = 1;
} else {
/* Disable USB charging */
+ dev_dbg(di->dev, "%s Disabled USB charging\n", __func__);
ret = abx500_set_register_interruptible(di->dev,
AB8500_CHARGER,
AB8500_USBCH_CTRL1_REG, 0);
@@ -1306,7 +1642,21 @@ static int ab8500_charger_usb_en(struct ux500_charger *charger,
ret = ab8500_charger_led_en(di, false);
if (ret < 0)
dev_err(di->dev, "failed to disable LED\n");
+ /* USBChInputCurr: current that can be drawn from the usb */
+ ret = ab8500_charger_set_vbus_in_curr(di, 0);
+ if (ret) {
+ dev_err(di->dev, "setting USBChInputCurr failed\n");
+ return ret;
+ }
+ /* ChOutputCurentLevel: protected output current */
+ ret = ab8500_charger_set_output_curr(di, 0);
+ if (ret) {
+ dev_err(di->dev, "%s "
+ "Failed to reset ChOutputCurentLevel\n",
+ __func__);
+ return ret;
+ }
di->usb.charger_online = 0;
di->usb.wd_expired = false;
@@ -1319,8 +1669,7 @@ static int ab8500_charger_usb_en(struct ux500_charger *charger,
dev_dbg(di->dev, "%s Disabled USB charging\n", __func__);
/* Cancel any pending Vbat check work */
- if (delayed_work_pending(&di->check_vbat_work))
- cancel_delayed_work(&di->check_vbat_work);
+ cancel_delayed_work(&di->check_vbat_work);
}
ab8500_power_supply_changed(di, &di->usb_chg.psy);
@@ -1328,6 +1677,128 @@ static int ab8500_charger_usb_en(struct ux500_charger *charger,
return ret;
}
+static int ab8500_external_charger_prepare(struct notifier_block *charger_nb,
+ unsigned long event, void *data)
+{
+ int ret;
+ struct device *dev = data;
+ /*Toggle External charger control pin*/
+ ret = abx500_set_register_interruptible(dev, AB8500_SYS_CTRL1_BLOCK,
+ AB8500_SYS_CHARGER_CONTROL_REG,
+ EXTERNAL_CHARGER_DISABLE_REG_VAL);
+ if (ret < 0) {
+ dev_err(dev, "write reg failed %d\n", ret);
+ goto out;
+ }
+ ret = abx500_set_register_interruptible(dev, AB8500_SYS_CTRL1_BLOCK,
+ AB8500_SYS_CHARGER_CONTROL_REG,
+ EXTERNAL_CHARGER_ENABLE_REG_VAL);
+ if (ret < 0)
+ dev_err(dev, "Write reg failed %d\n", ret);
+
+out:
+ return ret;
+}
+
+/**
+ * ab8500_charger_usb_check_enable() - enable usb charging
+ * @charger: pointer to the ux500_charger structure
+ * @vset: charging voltage
+ * @iset: charger output current
+ *
+ * Check if the VBUS charger has been disconnected and reconnected without
+ * AB8500 rising an interrupt. Returns 0 on success.
+ */
+static int ab8500_charger_usb_check_enable(struct ux500_charger *charger,
+ int vset, int iset)
+{
+ u8 usbch_ctrl1 = 0;
+ int ret = 0;
+
+ struct ab8500_charger *di = to_ab8500_charger_usb_device_info(charger);
+
+ if (!di->usb.charger_connected)
+ return ret;
+
+ ret = abx500_get_register_interruptible(di->dev, AB8500_CHARGER,
+ AB8500_USBCH_CTRL1_REG, &usbch_ctrl1);
+ if (ret < 0) {
+ dev_err(di->dev, "ab8500 read failed %d\n", __LINE__);
+ return ret;
+ }
+ dev_dbg(di->dev, "USB charger ctrl: 0x%02x\n", usbch_ctrl1);
+
+ if (!(usbch_ctrl1 & USB_CH_ENA)) {
+ dev_info(di->dev, "Charging has been disabled abnormally and will be re-enabled\n");
+
+ ret = abx500_mask_and_set_register_interruptible(di->dev,
+ AB8500_CHARGER, AB8500_CHARGER_CTRL,
+ DROP_COUNT_RESET, DROP_COUNT_RESET);
+ if (ret < 0) {
+ dev_err(di->dev, "ab8500 write failed %d\n", __LINE__);
+ return ret;
+ }
+
+ ret = ab8500_charger_usb_en(&di->usb_chg, true, vset, iset);
+ if (ret < 0) {
+ dev_err(di->dev, "Failed to enable VBUS charger %d\n",
+ __LINE__);
+ return ret;
+ }
+ }
+ return ret;
+}
+
+/**
+ * ab8500_charger_ac_check_enable() - enable usb charging
+ * @charger: pointer to the ux500_charger structure
+ * @vset: charging voltage
+ * @iset: charger output current
+ *
+ * Check if the AC charger has been disconnected and reconnected without
+ * AB8500 rising an interrupt. Returns 0 on success.
+ */
+static int ab8500_charger_ac_check_enable(struct ux500_charger *charger,
+ int vset, int iset)
+{
+ u8 mainch_ctrl1 = 0;
+ int ret = 0;
+
+ struct ab8500_charger *di = to_ab8500_charger_ac_device_info(charger);
+
+ if (!di->ac.charger_connected)
+ return ret;
+
+ ret = abx500_get_register_interruptible(di->dev, AB8500_CHARGER,
+ AB8500_MCH_CTRL1, &mainch_ctrl1);
+ if (ret < 0) {
+ dev_err(di->dev, "ab8500 read failed %d\n", __LINE__);
+ return ret;
+ }
+ dev_dbg(di->dev, "AC charger ctrl: 0x%02x\n", mainch_ctrl1);
+
+ if (!(mainch_ctrl1 & MAIN_CH_ENA)) {
+ dev_info(di->dev, "Charging has been disabled abnormally and will be re-enabled\n");
+
+ ret = abx500_mask_and_set_register_interruptible(di->dev,
+ AB8500_CHARGER, AB8500_CHARGER_CTRL,
+ DROP_COUNT_RESET, DROP_COUNT_RESET);
+
+ if (ret < 0) {
+ dev_err(di->dev, "ab8500 write failed %d\n", __LINE__);
+ return ret;
+ }
+
+ ret = ab8500_charger_ac_en(&di->usb_chg, true, vset, iset);
+ if (ret < 0) {
+ dev_err(di->dev, "failed to enable AC charger %d\n",
+ __LINE__);
+ return ret;
+ }
+ }
+ return ret;
+}
+
/**
* ab8500_charger_watchdog_kick() - kick charger watchdog
* @di: pointer to the ab8500_charger structure
@@ -1366,7 +1837,6 @@ static int ab8500_charger_update_charger_current(struct ux500_charger *charger,
int ich_out)
{
int ret;
- int curr_index;
struct ab8500_charger *di;
if (charger->psy.type == POWER_SUPPLY_TYPE_MAINS)
@@ -1376,25 +1846,78 @@ static int ab8500_charger_update_charger_current(struct ux500_charger *charger,
else
return -ENXIO;
- curr_index = ab8500_current_to_regval(ich_out);
- if (curr_index < 0) {
- dev_err(di->dev,
- "Charger current too high, "
- "charging not started\n");
- return -ENXIO;
+ ret = ab8500_charger_set_output_curr(di, ich_out);
+ if (ret) {
+ dev_err(di->dev, "%s "
+ "Failed to set ChOutputCurentLevel\n",
+ __func__);
+ return ret;
}
+ /* Reset the main and usb drop input current measurement counter */
ret = abx500_set_register_interruptible(di->dev, AB8500_CHARGER,
- AB8500_CH_OPT_CRNTLVL_REG, (u8) curr_index);
+ AB8500_CHARGER_CTRL, DROP_COUNT_RESET);
if (ret) {
dev_err(di->dev, "%s write failed\n", __func__);
return ret;
}
- /* Reset the main and usb drop input current measurement counter */
- ret = abx500_set_register_interruptible(di->dev, AB8500_CHARGER,
- AB8500_CHARGER_CTRL,
- 0x1);
+ return ret;
+}
+
+/**
+ * ab8540_charger_power_path_enable() - enable usb power path mode
+ * @charger: pointer to the ux500_charger structure
+ * @enable: enable/disable flag
+ *
+ * Enable or disable the power path for usb mode
+ * Returns error code in case of failure else 0(on success)
+ */
+static int ab8540_charger_power_path_enable(struct ux500_charger *charger,
+ bool enable)
+{
+ int ret;
+ struct ab8500_charger *di;
+
+ if (charger->psy.type == POWER_SUPPLY_TYPE_USB)
+ di = to_ab8500_charger_usb_device_info(charger);
+ else
+ return -ENXIO;
+
+ ret = abx500_mask_and_set_register_interruptible(di->dev,
+ AB8500_CHARGER, AB8540_USB_PP_MODE_REG,
+ BUS_POWER_PATH_MODE_ENA, enable);
+ if (ret) {
+ dev_err(di->dev, "%s write failed\n", __func__);
+ return ret;
+ }
+
+ return ret;
+}
+
+
+/**
+ * ab8540_charger_usb_pre_chg_enable() - enable usb pre change
+ * @charger: pointer to the ux500_charger structure
+ * @enable: enable/disable flag
+ *
+ * Enable or disable the pre-chage for usb mode
+ * Returns error code in case of failure else 0(on success)
+ */
+static int ab8540_charger_usb_pre_chg_enable(struct ux500_charger *charger,
+ bool enable)
+{
+ int ret;
+ struct ab8500_charger *di;
+
+ if (charger->psy.type == POWER_SUPPLY_TYPE_USB)
+ di = to_ab8500_charger_usb_device_info(charger);
+ else
+ return -ENXIO;
+
+ ret = abx500_mask_and_set_register_interruptible(di->dev,
+ AB8500_CHARGER, AB8540_USB_PP_CHR_REG,
+ BUS_POWER_PATH_PRECHG_ENA, enable);
if (ret) {
dev_err(di->dev, "%s write failed\n", __func__);
return ret;
@@ -1482,9 +2005,10 @@ static void ab8500_charger_check_vbat_work(struct work_struct *work)
di->vbat > VBAT_TRESH_IP_CUR_RED))) {
dev_dbg(di->dev, "Vbat did cross threshold, curr: %d, new: %d,"
- " old: %d\n", di->max_usb_in_curr, di->vbat,
- di->old_vbat);
- ab8500_charger_set_vbus_in_curr(di, di->max_usb_in_curr);
+ " old: %d\n", di->max_usb_in_curr.usb_type_max,
+ di->vbat, di->old_vbat);
+ ab8500_charger_set_vbus_in_curr(di,
+ di->max_usb_in_curr.usb_type_max);
power_supply_changed(&di->usb_chg.psy);
}
@@ -1597,7 +2121,7 @@ static void ab8500_charger_ac_work(struct work_struct *work)
* synchronously, we have the check if the main charger is
* connected by reading the status register
*/
- ret = ab8500_charger_detect_chargers(di);
+ ret = ab8500_charger_detect_chargers(di, false);
if (ret < 0)
return;
@@ -1612,6 +2136,84 @@ static void ab8500_charger_ac_work(struct work_struct *work)
sysfs_notify(&di->ac_chg.psy.dev->kobj, NULL, "present");
}
+static void ab8500_charger_usb_attached_work(struct work_struct *work)
+{
+ struct ab8500_charger *di = container_of(work,
+ struct ab8500_charger,
+ usb_charger_attached_work.work);
+ int usbch = (USB_CH_VBUSDROP | USB_CH_VBUSDETDBNC);
+ int ret, i;
+ u8 statval;
+
+ for (i = 0; i < 10; i++) {
+ ret = abx500_get_register_interruptible(di->dev,
+ AB8500_CHARGER,
+ AB8500_CH_USBCH_STAT1_REG,
+ &statval);
+ if (ret < 0) {
+ dev_err(di->dev, "ab8500 read failed %d\n", __LINE__);
+ goto reschedule;
+ }
+ if ((statval & usbch) != usbch)
+ goto reschedule;
+
+ msleep(CHARGER_STATUS_POLL);
+ }
+
+ ab8500_charger_usb_en(&di->usb_chg, 0, 0, 0);
+
+ mutex_lock(&di->charger_attached_mutex);
+ mutex_unlock(&di->charger_attached_mutex);
+
+ return;
+
+reschedule:
+ queue_delayed_work(di->charger_wq,
+ &di->usb_charger_attached_work,
+ HZ);
+}
+
+static void ab8500_charger_ac_attached_work(struct work_struct *work)
+{
+
+ struct ab8500_charger *di = container_of(work,
+ struct ab8500_charger,
+ ac_charger_attached_work.work);
+ int mainch = (MAIN_CH_STATUS2_MAINCHGDROP |
+ MAIN_CH_STATUS2_MAINCHARGERDETDBNC);
+ int ret, i;
+ u8 statval;
+
+ for (i = 0; i < 10; i++) {
+ ret = abx500_get_register_interruptible(di->dev,
+ AB8500_CHARGER,
+ AB8500_CH_STATUS2_REG,
+ &statval);
+ if (ret < 0) {
+ dev_err(di->dev, "ab8500 read failed %d\n", __LINE__);
+ goto reschedule;
+ }
+
+ if ((statval & mainch) != mainch)
+ goto reschedule;
+
+ msleep(CHARGER_STATUS_POLL);
+ }
+
+ ab8500_charger_ac_en(&di->ac_chg, 0, 0, 0);
+ queue_work(di->charger_wq, &di->ac_work);
+
+ mutex_lock(&di->charger_attached_mutex);
+ mutex_unlock(&di->charger_attached_mutex);
+
+ return;
+
+reschedule:
+ queue_delayed_work(di->charger_wq,
+ &di->ac_charger_attached_work,
+ HZ);
+}
+
/**
* ab8500_charger_detect_usb_type_work() - work to detect USB type
* @work: Pointer to the work_struct structure
@@ -1630,16 +2232,18 @@ static void ab8500_charger_detect_usb_type_work(struct work_struct *work)
* synchronously, we have the check if is
* connected by reading the status register
*/
- ret = ab8500_charger_detect_chargers(di);
+ ret = ab8500_charger_detect_chargers(di, false);
if (ret < 0)
return;
if (!(ret & USB_PW_CONN)) {
- di->vbus_detected = 0;
+ dev_dbg(di->dev, "%s di->vbus_detected = false\n", __func__);
+ di->vbus_detected = false;
ab8500_charger_set_usb_connected(di, false);
ab8500_power_supply_changed(di, &di->usb_chg.psy);
} else {
- di->vbus_detected = 1;
+ dev_dbg(di->dev, "%s di->vbus_detected = true\n", __func__);
+ di->vbus_detected = true;
if (is_ab8500_1p1_or_earlier(di->parent)) {
ret = ab8500_charger_detect_usb_type(di);
@@ -1649,7 +2253,8 @@ static void ab8500_charger_detect_usb_type_work(struct work_struct *work)
&di->usb_chg.psy);
}
} else {
- /* For ABB cut2.0 and onwards we have an IRQ,
+ /*
+ * For ABB cut2.0 and onwards we have an IRQ,
* USB_LINK_STATUS that will be triggered when the USB
* link status changes. The exception is USB connected
* during startup. Then we don't get a
@@ -1670,6 +2275,30 @@ static void ab8500_charger_detect_usb_type_work(struct work_struct *work)
}
/**
+ * ab8500_charger_usb_link_attach_work() - work to detect USB type
+ * @work: pointer to the work_struct structure
+ *
+ * Detect the type of USB plugged
+ */
+static void ab8500_charger_usb_link_attach_work(struct work_struct *work)
+{
+ struct ab8500_charger *di =
+ container_of(work, struct ab8500_charger, attach_work.work);
+ int ret;
+
+ /* Update maximum input current if USB enumeration is not detected */
+ if (!di->usb.charger_online) {
+ ret = ab8500_charger_set_vbus_in_curr(di,
+ di->max_usb_in_curr.usb_type_max);
+ if (ret)
+ return;
+ }
+
+ ab8500_charger_set_usb_connected(di, true);
+ ab8500_power_supply_changed(di, &di->usb_chg.psy);
+}
+
+/**
* ab8500_charger_usb_link_status_work() - work to detect USB type
* @work: pointer to the work_struct structure
*
@@ -1677,7 +2306,10 @@ static void ab8500_charger_detect_usb_type_work(struct work_struct *work)
*/
static void ab8500_charger_usb_link_status_work(struct work_struct *work)
{
+ int detected_chargers;
int ret;
+ u8 val;
+ u8 link_status;
struct ab8500_charger *di = container_of(work,
struct ab8500_charger, usb_link_status_work);
@@ -1687,31 +2319,118 @@ static void ab8500_charger_usb_link_status_work(struct work_struct *work)
* synchronously, we have the check if is
* connected by reading the status register
*/
- ret = ab8500_charger_detect_chargers(di);
- if (ret < 0)
+ detected_chargers = ab8500_charger_detect_chargers(di, false);
+ if (detected_chargers < 0)
return;
- if (!(ret & USB_PW_CONN)) {
- di->vbus_detected = 0;
+ /*
+ * Some chargers that breaks the USB spec is
+ * identified as invalid by AB8500 and it refuse
+ * to start the charging process. but by jumping
+ * thru a few hoops it can be forced to start.
+ */
+ if (is_ab8500(di->parent))
+ ret = abx500_get_register_interruptible(di->dev, AB8500_USB,
+ AB8500_USB_LINE_STAT_REG, &val);
+ else
+ ret = abx500_get_register_interruptible(di->dev, AB8500_USB,
+ AB8500_USB_LINK1_STAT_REG, &val);
+
+ if (ret >= 0)
+ dev_dbg(di->dev, "UsbLineStatus register = 0x%02x\n", val);
+ else
+ dev_dbg(di->dev, "Error reading USB link status\n");
+
+ if (is_ab8500(di->parent))
+ link_status = AB8500_USB_LINK_STATUS;
+ else
+ link_status = AB8505_USB_LINK_STATUS;
+
+ if (detected_chargers & USB_PW_CONN) {
+ if (((val & link_status) >> USB_LINK_STATUS_SHIFT) ==
+ USB_STAT_NOT_VALID_LINK &&
+ di->invalid_charger_detect_state == 0) {
+ dev_dbg(di->dev,
+ "Invalid charger detected, state= 0\n");
+ /*Enable charger*/
+ abx500_mask_and_set_register_interruptible(di->dev,
+ AB8500_CHARGER, AB8500_USBCH_CTRL1_REG,
+ USB_CH_ENA, USB_CH_ENA);
+ /*Enable charger detection*/
+ abx500_mask_and_set_register_interruptible(di->dev,
+ AB8500_USB, AB8500_USB_LINE_CTRL2_REG,
+ USB_CH_DET, USB_CH_DET);
+ di->invalid_charger_detect_state = 1;
+ /*exit and wait for new link status interrupt.*/
+ return;
+
+ }
+ if (di->invalid_charger_detect_state == 1) {
+ dev_dbg(di->dev,
+ "Invalid charger detected, state= 1\n");
+ /*Stop charger detection*/
+ abx500_mask_and_set_register_interruptible(di->dev,
+ AB8500_USB, AB8500_USB_LINE_CTRL2_REG,
+ USB_CH_DET, 0x00);
+ /*Check link status*/
+ if (is_ab8500(di->parent))
+ ret = abx500_get_register_interruptible(di->dev,
+ AB8500_USB, AB8500_USB_LINE_STAT_REG,
+ &val);
+ else
+ ret = abx500_get_register_interruptible(di->dev,
+ AB8500_USB, AB8500_USB_LINK1_STAT_REG,
+ &val);
+
+ dev_dbg(di->dev, "USB link status= 0x%02x\n",
+ (val & link_status) >> USB_LINK_STATUS_SHIFT);
+ di->invalid_charger_detect_state = 2;
+ }
+ } else {
+ di->invalid_charger_detect_state = 0;
+ }
+
+ if (!(detected_chargers & USB_PW_CONN)) {
+ di->vbus_detected = false;
ab8500_charger_set_usb_connected(di, false);
ab8500_power_supply_changed(di, &di->usb_chg.psy);
- } else {
- di->vbus_detected = 1;
- ret = ab8500_charger_read_usb_type(di);
- if (!ret) {
- /* Update maximum input current */
- ret = ab8500_charger_set_vbus_in_curr(di,
- di->max_usb_in_curr);
- if (ret)
- return;
+ return;
+ }
- ab8500_charger_set_usb_connected(di, true);
- ab8500_power_supply_changed(di, &di->usb_chg.psy);
- } else if (ret == -ENXIO) {
+ dev_dbg(di->dev,"%s di->vbus_detected = true\n",__func__);
+ di->vbus_detected = true;
+ ret = ab8500_charger_read_usb_type(di);
+ if (ret) {
+ if (ret == -ENXIO) {
/* No valid charger type detected */
ab8500_charger_set_usb_connected(di, false);
ab8500_power_supply_changed(di, &di->usb_chg.psy);
}
+ return;
+ }
+
+ if (di->usb_device_is_unrecognised) {
+ dev_dbg(di->dev,
+ "Potential Legacy Charger device. "
+ "Delay work for %d msec for USB enum "
+ "to finish",
+ WAIT_ACA_RID_ENUMERATION);
+ queue_delayed_work(di->charger_wq,
+ &di->attach_work,
+ msecs_to_jiffies(WAIT_ACA_RID_ENUMERATION));
+ } else if (di->is_aca_rid == 1) {
+ /* Only wait once */
+ di->is_aca_rid++;
+ dev_dbg(di->dev,
+ "%s Wait %d msec for USB enum to finish",
+ __func__, WAIT_ACA_RID_ENUMERATION);
+ queue_delayed_work(di->charger_wq,
+ &di->attach_work,
+ msecs_to_jiffies(WAIT_ACA_RID_ENUMERATION));
+ } else {
+ queue_delayed_work(di->charger_wq,
+ &di->attach_work,
+ 0);
}
}
@@ -1721,24 +2440,20 @@ static void ab8500_charger_usb_state_changed_work(struct work_struct *work)
unsigned long flags;
struct ab8500_charger *di = container_of(work,
- struct ab8500_charger, usb_state_changed_work);
+ struct ab8500_charger, usb_state_changed_work.work);
- if (!di->vbus_detected)
+ if (!di->vbus_detected) {
+ dev_dbg(di->dev,
+ "%s !di->vbus_detected\n",
+ __func__);
return;
+ }
spin_lock_irqsave(&di->usb_state.usb_lock, flags);
- di->usb_state.usb_changed = false;
+ di->usb_state.state = di->usb_state.state_tmp;
+ di->usb_state.usb_current = di->usb_state.usb_current_tmp;
spin_unlock_irqrestore(&di->usb_state.usb_lock, flags);
- /*
- * wait for some time until you get updates from the usb stack
- * and negotiations are completed
- */
- msleep(250);
-
- if (di->usb_state.usb_changed)
- return;
-
dev_dbg(di->dev, "%s USB state: 0x%02x mA: %d\n",
__func__, di->usb_state.state, di->usb_state.usb_current);
@@ -1766,7 +2481,7 @@ static void ab8500_charger_usb_state_changed_work(struct work_struct *work)
if (!ab8500_charger_get_usb_cur(di)) {
/* Update maximum input current */
ret = ab8500_charger_set_vbus_in_curr(di,
- di->max_usb_in_curr);
+ di->max_usb_in_curr.usb_type_max);
if (ret)
return;
@@ -1892,6 +2607,10 @@ static irqreturn_t ab8500_charger_mainchunplugdet_handler(int irq, void *_di)
dev_dbg(di->dev, "Main charger unplugged\n");
queue_work(di->charger_wq, &di->ac_work);
+ cancel_delayed_work_sync(&di->ac_charger_attached_work);
+ mutex_lock(&di->charger_attached_mutex);
+ mutex_unlock(&di->charger_attached_mutex);
+
return IRQ_HANDLED;
}
@@ -1909,6 +2628,13 @@ static irqreturn_t ab8500_charger_mainchplugdet_handler(int irq, void *_di)
dev_dbg(di->dev, "Main charger plugged\n");
queue_work(di->charger_wq, &di->ac_work);
+ mutex_lock(&di->charger_attached_mutex);
+ mutex_unlock(&di->charger_attached_mutex);
+
+ if (is_ab8500(di->parent))
+ queue_delayed_work(di->charger_wq,
+ &di->ac_charger_attached_work,
+ HZ);
return IRQ_HANDLED;
}
@@ -1971,6 +2697,60 @@ static irqreturn_t ab8500_charger_mainchthprotf_handler(int irq, void *_di)
return IRQ_HANDLED;
}
+static void ab8500_charger_vbus_drop_end_work(struct work_struct *work)
+{
+ struct ab8500_charger *di = container_of(work,
+ struct ab8500_charger, vbus_drop_end_work.work);
+ int ret, curr;
+ u8 reg_value;
+
+ di->flags.vbus_drop_end = false;
+
+ /* Reset the drop counter */
+ abx500_set_register_interruptible(di->dev,
+ AB8500_CHARGER, AB8500_CHARGER_CTRL, 0x01);
+
+ if (is_ab8540(di->parent))
+ ret = abx500_get_register_interruptible(di->dev, AB8500_CHARGER,
+ AB8540_CH_USBCH_STAT3_REG, &reg_value);
+ else
+ ret = abx500_get_register_interruptible(di->dev, AB8500_CHARGER,
+ AB8500_CH_USBCH_STAT2_REG, &reg_value);
+ if (ret < 0) {
+ dev_err(di->dev, "%s read failed\n", __func__);
+ return;
+ }
+
+ if (is_ab8540(di->parent))
+ curr = di->bm->chg_input_curr[
+ reg_value & AB8540_AUTO_VBUS_IN_CURR_MASK];
+ else
+ curr = di->bm->chg_input_curr[
+ reg_value >> AUTO_VBUS_IN_CURR_LIM_SHIFT];
+
+ if (di->max_usb_in_curr.calculated_max != curr) {
+ /* USB source is collapsing */
+ di->max_usb_in_curr.calculated_max = curr;
+ dev_dbg(di->dev,
+ "VBUS input current limiting to %d mA\n",
+ di->max_usb_in_curr.calculated_max);
+ } else {
+ /*
+ * USB source can not give more than this amount.
+ * Taking more will collapse the source.
+ */
+ di->max_usb_in_curr.set_max =
+ di->max_usb_in_curr.calculated_max;
+ dev_dbg(di->dev,
+ "VBUS input current limited to %d mA\n",
+ di->max_usb_in_curr.set_max);
+ }
+
+ if (di->usb.charger_connected)
+ ab8500_charger_set_vbus_in_curr(di,
+ di->max_usb_in_curr.usb_type_max);
+}
+
/**
* ab8500_charger_vbusdetf_handler() - VBUS falling detected
* @irq: interrupt number
@@ -1982,6 +2762,7 @@ static irqreturn_t ab8500_charger_vbusdetf_handler(int irq, void *_di)
{
struct ab8500_charger *di = _di;
+ di->vbus_detected = false;
dev_dbg(di->dev, "VBUS falling detected\n");
queue_work(di->charger_wq, &di->detect_usb_type_work);
@@ -2001,6 +2782,7 @@ static irqreturn_t ab8500_charger_vbusdetr_handler(int irq, void *_di)
di->vbus_detected = true;
dev_dbg(di->dev, "VBUS rising detected\n");
+
queue_work(di->charger_wq, &di->detect_usb_type_work);
return IRQ_HANDLED;
@@ -2109,6 +2891,30 @@ static irqreturn_t ab8500_charger_chwdexp_handler(int irq, void *_di)
}
/**
+ * ab8500_charger_vbuschdropend_handler() - VBUS drop removed
+ * @irq: interrupt number
+ * @_di: pointer to the ab8500_charger structure
+ *
+ * Returns IRQ status(IRQ_HANDLED)
+ */
+static irqreturn_t ab8500_charger_vbuschdropend_handler(int irq, void *_di)
+{
+ struct ab8500_charger *di = _di;
+
+ dev_dbg(di->dev, "VBUS charger drop ended\n");
+ di->flags.vbus_drop_end = true;
+
+ /*
+ * VBUS might have dropped due to bad connection.
+ * Schedule a new input limit set to the value SW requests.
+ */
+ queue_delayed_work(di->charger_wq, &di->vbus_drop_end_work,
+ round_jiffies(VBUS_IN_CURR_LIM_RETRY_SET_TIME * HZ));
+
+ return IRQ_HANDLED;
+}
+
+/**
* ab8500_charger_vbusovv_handler() - VBUS overvoltage detected
* @irq: interrupt number
* @_di: pointer to the ab8500_charger structure
@@ -2148,6 +2954,7 @@ static int ab8500_charger_ac_get_property(struct power_supply *psy,
union power_supply_propval *val)
{
struct ab8500_charger *di;
+ int ret;
di = to_ab8500_charger_ac_device_info(psy_to_ux500_charger(psy));
@@ -2169,7 +2976,10 @@ static int ab8500_charger_ac_get_property(struct power_supply *psy,
val->intval = di->ac.charger_connected;
break;
case POWER_SUPPLY_PROP_VOLTAGE_NOW:
- di->ac.charger_voltage = ab8500_charger_get_ac_voltage(di);
+ ret = ab8500_charger_get_ac_voltage(di);
+ if (ret >= 0)
+ di->ac.charger_voltage = ret;
+ /* On error, use previous value */
val->intval = di->ac.charger_voltage * 1000;
break;
case POWER_SUPPLY_PROP_VOLTAGE_AVG:
@@ -2181,7 +2991,10 @@ static int ab8500_charger_ac_get_property(struct power_supply *psy,
val->intval = di->ac.cv_active;
break;
case POWER_SUPPLY_PROP_CURRENT_NOW:
- val->intval = ab8500_charger_get_ac_current(di) * 1000;
+ ret = ab8500_charger_get_ac_current(di);
+ if (ret >= 0)
+ di->ac.charger_current = ret;
+ val->intval = di->ac.charger_current * 1000;
break;
default:
return -EINVAL;
@@ -2208,6 +3021,7 @@ static int ab8500_charger_usb_get_property(struct power_supply *psy,
union power_supply_propval *val)
{
struct ab8500_charger *di;
+ int ret;
di = to_ab8500_charger_usb_device_info(psy_to_ux500_charger(psy));
@@ -2231,7 +3045,9 @@ static int ab8500_charger_usb_get_property(struct power_supply *psy,
val->intval = di->usb.charger_connected;
break;
case POWER_SUPPLY_PROP_VOLTAGE_NOW:
- di->usb.charger_voltage = ab8500_charger_get_vbus_voltage(di);
+ ret = ab8500_charger_get_vbus_voltage(di);
+ if (ret >= 0)
+ di->usb.charger_voltage = ret;
val->intval = di->usb.charger_voltage * 1000;
break;
case POWER_SUPPLY_PROP_VOLTAGE_AVG:
@@ -2243,7 +3059,10 @@ static int ab8500_charger_usb_get_property(struct power_supply *psy,
val->intval = di->usb.cv_active;
break;
case POWER_SUPPLY_PROP_CURRENT_NOW:
- val->intval = ab8500_charger_get_usb_current(di) * 1000;
+ ret = ab8500_charger_get_usb_current(di);
+ if (ret >= 0)
+ di->usb.charger_current = ret;
+ val->intval = di->usb.charger_current * 1000;
break;
case POWER_SUPPLY_PROP_CURRENT_AVG:
/*
@@ -2271,6 +3090,7 @@ static int ab8500_charger_usb_get_property(struct power_supply *psy,
static int ab8500_charger_init_hw_registers(struct ab8500_charger *di)
{
int ret = 0;
+ u8 bup_vch_range = 0, vbup33_vrtcn = 0;
/* Setup maximum charger current and voltage for ABB cut2.0 */
if (!is_ab8500_1p1_or_earlier(di->parent)) {
@@ -2283,9 +3103,14 @@ static int ab8500_charger_init_hw_registers(struct ab8500_charger *di)
goto out;
}
- ret = abx500_set_register_interruptible(di->dev,
- AB8500_CHARGER,
- AB8500_CH_OPT_CRNTLVL_MAX_REG, CH_OP_CUR_LVL_1P6);
+ if (is_ab8540(di->parent))
+ ret = abx500_set_register_interruptible(di->dev,
+ AB8500_CHARGER, AB8500_CH_OPT_CRNTLVL_MAX_REG,
+ CH_OP_CUR_LVL_2P);
+ else
+ ret = abx500_set_register_interruptible(di->dev,
+ AB8500_CHARGER, AB8500_CH_OPT_CRNTLVL_MAX_REG,
+ CH_OP_CUR_LVL_1P6);
if (ret) {
dev_err(di->dev,
"failed to set CH_OPT_CRNTLVL_MAX_REG\n");
@@ -2293,13 +3118,24 @@ static int ab8500_charger_init_hw_registers(struct ab8500_charger *di)
}
}
- /* VBUS OVV set to 6.3V and enable automatic current limitiation */
- ret = abx500_set_register_interruptible(di->dev,
- AB8500_CHARGER,
- AB8500_USBCH_CTRL2_REG,
- VBUS_OVV_SELECT_6P3V | VBUS_AUTO_IN_CURR_LIM_ENA);
+ if (is_ab9540_2p0(di->parent) || is_ab9540_3p0(di->parent)
+ || is_ab8505_2p0(di->parent) || is_ab8540(di->parent))
+ ret = abx500_mask_and_set_register_interruptible(di->dev,
+ AB8500_CHARGER,
+ AB8500_USBCH_CTRL2_REG,
+ VBUS_AUTO_IN_CURR_LIM_ENA,
+ VBUS_AUTO_IN_CURR_LIM_ENA);
+ else
+ /*
+ * VBUS OVV set to 6.3V and enable automatic current limitation
+ */
+ ret = abx500_set_register_interruptible(di->dev,
+ AB8500_CHARGER,
+ AB8500_USBCH_CTRL2_REG,
+ VBUS_OVV_SELECT_6P3V | VBUS_AUTO_IN_CURR_LIM_ENA);
if (ret) {
- dev_err(di->dev, "failed to set VBUS OVV\n");
+ dev_err(di->dev,
+ "failed to set automatic current limitation\n");
goto out;
}
@@ -2355,16 +3191,37 @@ static int ab8500_charger_init_hw_registers(struct ab8500_charger *di)
goto out;
}
+ ret = ab8500_charger_led_en(di, false);
+ if (ret < 0) {
+ dev_err(di->dev, "failed to disable LED\n");
+ goto out;
+ }
+
/* Backup battery voltage and current */
+ if (di->bm->bkup_bat_v > BUP_VCH_SEL_3P1V)
+ bup_vch_range = BUP_VCH_RANGE;
+ if (di->bm->bkup_bat_v == BUP_VCH_SEL_3P3V)
+ vbup33_vrtcn = VBUP33_VRTCN;
+
ret = abx500_set_register_interruptible(di->dev,
AB8500_RTC,
AB8500_RTC_BACKUP_CHG_REG,
- di->bat->bkup_bat_v |
- di->bat->bkup_bat_i);
+ (di->bm->bkup_bat_v & 0x3) | di->bm->bkup_bat_i);
if (ret) {
dev_err(di->dev, "failed to setup backup battery charging\n");
goto out;
}
+ if (is_ab8540(di->parent)) {
+ ret = abx500_set_register_interruptible(di->dev,
+ AB8500_RTC,
+ AB8500_RTC_CTRL1_REG,
+ bup_vch_range | vbup33_vrtcn);
+ if (ret) {
+ dev_err(di->dev,
+ "failed to setup backup battery charging\n");
+ goto out;
+ }
+ }
/* Enable backup battery charging */
abx500_mask_and_set_register_interruptible(di->dev,
@@ -2373,6 +3230,25 @@ static int ab8500_charger_init_hw_registers(struct ab8500_charger *di)
if (ret < 0)
dev_err(di->dev, "%s mask and set failed\n", __func__);
+ if (is_ab8540(di->parent)) {
+ ret = abx500_mask_and_set_register_interruptible(di->dev,
+ AB8500_CHARGER, AB8540_USB_PP_MODE_REG,
+ BUS_VSYS_VOL_SELECT_MASK, BUS_VSYS_VOL_SELECT_3P6V);
+ if (ret) {
+ dev_err(di->dev,
+ "failed to setup usb power path vsys voltage\n");
+ goto out;
+ }
+ ret = abx500_mask_and_set_register_interruptible(di->dev,
+ AB8500_CHARGER, AB8540_USB_PP_CHR_REG,
+ BUS_PP_PRECHG_CURRENT_MASK, 0);
+ if (ret) {
+ dev_err(di->dev,
+ "failed to setup usb power path prechage current\n");
+ goto out;
+ }
+ }
+
out:
return ret;
}
@@ -2394,6 +3270,7 @@ static struct ab8500_charger_interrupts ab8500_charger_irq[] = {
{"USB_CHARGER_NOT_OKR", ab8500_charger_usbchargernotokr_handler},
{"VBUS_OVV", ab8500_charger_vbusovv_handler},
{"CH_WD_EXP", ab8500_charger_chwdexp_handler},
+ {"VBUS_CH_DROP_END", ab8500_charger_vbuschdropend_handler},
};
static int ab8500_charger_usb_notifier_call(struct notifier_block *nb,
@@ -2404,6 +3281,9 @@ static int ab8500_charger_usb_notifier_call(struct notifier_block *nb,
enum ab8500_usb_state bm_usb_state;
unsigned mA = *((unsigned *)power);
+ if (!di)
+ return NOTIFY_DONE;
+
if (event != USB_EVENT_VBUS) {
dev_dbg(di->dev, "not a standard host, returning\n");
return NOTIFY_DONE;
@@ -2427,13 +3307,15 @@ static int ab8500_charger_usb_notifier_call(struct notifier_block *nb,
__func__, bm_usb_state, mA);
spin_lock(&di->usb_state.usb_lock);
- di->usb_state.usb_changed = true;
+ di->usb_state.state_tmp = bm_usb_state;
+ di->usb_state.usb_current_tmp = mA;
spin_unlock(&di->usb_state.usb_lock);
- di->usb_state.state = bm_usb_state;
- di->usb_state.usb_current = mA;
-
- queue_work(di->charger_wq, &di->usb_state_changed_work);
+ /*
+ * wait for some time until you get updates from the usb stack
+ * and negotiations are completed
+ */
+ queue_delayed_work(di->charger_wq, &di->usb_state_changed_work, HZ/2);
return NOTIFY_OK;
}
@@ -2460,11 +3342,8 @@ static int ab8500_charger_resume(struct platform_device *pdev)
dev_err(di->dev, "Failed to kick WD!\n");
/* If not already pending start a new timer */
- if (!delayed_work_pending(
- &di->kick_wd_work)) {
- queue_delayed_work(di->charger_wq, &di->kick_wd_work,
- round_jiffies(WD_KICK_INTERVAL));
- }
+ queue_delayed_work(di->charger_wq, &di->kick_wd_work,
+ round_jiffies(WD_KICK_INTERVAL));
}
/* If we still have a HW failure, schedule a new check */
@@ -2473,6 +3352,9 @@ static int ab8500_charger_resume(struct platform_device *pdev)
&di->check_hw_failure_work, 0);
}
+ if (di->flags.vbus_drop_end)
+ queue_delayed_work(di->charger_wq, &di->vbus_drop_end_work, 0);
+
return 0;
}
@@ -2481,9 +3363,23 @@ static int ab8500_charger_suspend(struct platform_device *pdev,
{
struct ab8500_charger *di = platform_get_drvdata(pdev);
- /* Cancel any pending HW failure check */
- if (delayed_work_pending(&di->check_hw_failure_work))
- cancel_delayed_work(&di->check_hw_failure_work);
+ /* Cancel any pending jobs */
+ cancel_delayed_work(&di->check_hw_failure_work);
+ cancel_delayed_work(&di->vbus_drop_end_work);
+
+ flush_delayed_work(&di->attach_work);
+ flush_delayed_work(&di->usb_charger_attached_work);
+ flush_delayed_work(&di->ac_charger_attached_work);
+ flush_delayed_work(&di->check_usbchgnotok_work);
+ flush_delayed_work(&di->check_vbat_work);
+ flush_delayed_work(&di->kick_wd_work);
+
+ flush_work(&di->usb_link_status_work);
+ flush_work(&di->ac_work);
+ flush_work(&di->detect_usb_type_work);
+
+ if (atomic_read(&di->current_stepping_sessions))
+ return -EAGAIN;
return 0;
}
@@ -2492,6 +3388,10 @@ static int ab8500_charger_suspend(struct platform_device *pdev,
#define ab8500_charger_resume NULL
#endif
+static struct notifier_block charger_nb = {
+ .notifier_call = ab8500_external_charger_prepare,
+};
+
static int ab8500_charger_remove(struct platform_device *pdev)
{
struct ab8500_charger *di = platform_get_drvdata(pdev);
@@ -2509,9 +3409,6 @@ static int ab8500_charger_remove(struct platform_device *pdev)
free_irq(irq, di);
}
- /* disable the regulator */
- regulator_put(di->regu);
-
/* Backup battery voltage and current disable */
ret = abx500_mask_and_set_register_interruptible(di->dev,
AB8500_RTC, AB8500_RTC_CTRL_REG, RTC_BUP_CH_ENA, 0);
@@ -2524,10 +3421,17 @@ static int ab8500_charger_remove(struct platform_device *pdev)
/* Delete the work queue */
destroy_workqueue(di->charger_wq);
+ /* Unregister external charger enable notifier */
+ if (!di->ac_chg.enabled)
+ blocking_notifier_chain_unregister(
+ &charger_notifier_list, &charger_nb);
+
flush_scheduled_work();
- power_supply_unregister(&di->usb_chg.psy);
- power_supply_unregister(&di->ac_chg.psy);
- platform_set_drvdata(pdev, NULL);
+ if (di->usb_chg.enabled)
+ power_supply_unregister(&di->usb_chg.psy);
+
+ if (di->ac_chg.enabled && !di->ac_chg.external)
+ power_supply_unregister(&di->ac_chg.psy);
return 0;
}
@@ -2541,32 +3445,31 @@ static char *supply_interface[] = {
static int ab8500_charger_probe(struct platform_device *pdev)
{
struct device_node *np = pdev->dev.of_node;
+ struct abx500_bm_data *plat = pdev->dev.platform_data;
struct ab8500_charger *di;
- int irq, i, charger_status, ret = 0;
+ int irq, i, charger_status, ret = 0, ch_stat;
di = devm_kzalloc(&pdev->dev, sizeof(*di), GFP_KERNEL);
if (!di) {
dev_err(&pdev->dev, "%s no mem for ab8500_charger\n", __func__);
return -ENOMEM;
}
- di->bat = pdev->mfd_cell->platform_data;
- if (!di->bat) {
- if (np) {
- ret = bmdevs_of_probe(&pdev->dev, np, &di->bat);
- if (ret) {
- dev_err(&pdev->dev,
- "failed to get battery information\n");
- return ret;
- }
- di->autopower_cfg = of_property_read_bool(np, "autopower_cfg");
- } else {
- dev_err(&pdev->dev, "missing dt node for ab8500_charger\n");
- return -EINVAL;
+
+ if (!plat) {
+ dev_err(&pdev->dev, "no battery management data supplied\n");
+ return -EINVAL;
+ }
+ di->bm = plat;
+
+ if (np) {
+ ret = ab8500_bm_of_probe(&pdev->dev, np, di->bm);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to get battery information\n");
+ return ret;
}
- } else {
- dev_info(&pdev->dev, "falling back to legacy platform data\n");
+ di->autopower_cfg = of_property_read_bool(np, "autopower_cfg");
+ } else
di->autopower_cfg = false;
- }
/* get parent data */
di->dev = &pdev->dev;
@@ -2575,8 +3478,10 @@ static int ab8500_charger_probe(struct platform_device *pdev)
/* initialize lock */
spin_lock_init(&di->usb_state.usb_lock);
+ mutex_init(&di->usb_ipt_crnt_lock);
di->autopower = false;
+ di->invalid_charger_detect_state = 0;
/* AC supply */
/* power_supply base class */
@@ -2589,12 +3494,21 @@ static int ab8500_charger_probe(struct platform_device *pdev)
di->ac_chg.psy.num_supplicants = ARRAY_SIZE(supply_interface),
/* ux500_charger sub-class */
di->ac_chg.ops.enable = &ab8500_charger_ac_en;
+ di->ac_chg.ops.check_enable = &ab8500_charger_ac_check_enable;
di->ac_chg.ops.kick_wd = &ab8500_charger_watchdog_kick;
di->ac_chg.ops.update_curr = &ab8500_charger_update_charger_current;
di->ac_chg.max_out_volt = ab8500_charger_voltage_map[
ARRAY_SIZE(ab8500_charger_voltage_map) - 1];
- di->ac_chg.max_out_curr = ab8500_charger_current_map[
- ARRAY_SIZE(ab8500_charger_current_map) - 1];
+ di->ac_chg.max_out_curr =
+ di->bm->chg_output_curr[di->bm->n_chg_out_curr - 1];
+ di->ac_chg.wdt_refresh = CHG_WD_INTERVAL;
+ di->ac_chg.enabled = di->bm->ac_enabled;
+ di->ac_chg.external = false;
+
+ /*notifier for external charger enabling*/
+ if (!di->ac_chg.enabled)
+ blocking_notifier_chain_register(
+ &charger_notifier_list, &charger_nb);
/* USB supply */
/* power_supply base class */
@@ -2607,13 +3521,20 @@ static int ab8500_charger_probe(struct platform_device *pdev)
di->usb_chg.psy.num_supplicants = ARRAY_SIZE(supply_interface),
/* ux500_charger sub-class */
di->usb_chg.ops.enable = &ab8500_charger_usb_en;
+ di->usb_chg.ops.check_enable = &ab8500_charger_usb_check_enable;
di->usb_chg.ops.kick_wd = &ab8500_charger_watchdog_kick;
di->usb_chg.ops.update_curr = &ab8500_charger_update_charger_current;
+ di->usb_chg.ops.pp_enable = &ab8540_charger_power_path_enable;
+ di->usb_chg.ops.pre_chg_enable = &ab8540_charger_usb_pre_chg_enable;
di->usb_chg.max_out_volt = ab8500_charger_voltage_map[
ARRAY_SIZE(ab8500_charger_voltage_map) - 1];
- di->usb_chg.max_out_curr = ab8500_charger_current_map[
- ARRAY_SIZE(ab8500_charger_current_map) - 1];
-
+ di->usb_chg.max_out_curr =
+ di->bm->chg_output_curr[di->bm->n_chg_out_curr - 1];
+ di->usb_chg.wdt_refresh = CHG_WD_INTERVAL;
+ di->usb_chg.enabled = di->bm->usb_enabled;
+ di->usb_chg.external = false;
+ di->usb_chg.power_path = di->bm->usb_power_path;
+ di->usb_state.usb_current = -1;
/* Create a work queue for the charger */
di->charger_wq =
@@ -2623,12 +3544,19 @@ static int ab8500_charger_probe(struct platform_device *pdev)
return -ENOMEM;
}
+ mutex_init(&di->charger_attached_mutex);
+
/* Init work for HW failure check */
INIT_DEFERRABLE_WORK(&di->check_hw_failure_work,
ab8500_charger_check_hw_failure_work);
INIT_DEFERRABLE_WORK(&di->check_usbchgnotok_work,
ab8500_charger_check_usbchargernotok_work);
+ INIT_DELAYED_WORK(&di->ac_charger_attached_work,
+ ab8500_charger_ac_attached_work);
+ INIT_DELAYED_WORK(&di->usb_charger_attached_work,
+ ab8500_charger_usb_attached_work);
+
/*
* For ABB revision 1.0 and 1.1 there is a bug in the watchdog
* logic. That means we have to continously kick the charger
@@ -2644,6 +3572,15 @@ static int ab8500_charger_probe(struct platform_device *pdev)
INIT_DEFERRABLE_WORK(&di->check_vbat_work,
ab8500_charger_check_vbat_work);
+ INIT_DELAYED_WORK(&di->attach_work,
+ ab8500_charger_usb_link_attach_work);
+
+ INIT_DELAYED_WORK(&di->usb_state_changed_work,
+ ab8500_charger_usb_state_changed_work);
+
+ INIT_DELAYED_WORK(&di->vbus_drop_end_work,
+ ab8500_charger_vbus_drop_end_work);
+
/* Init work for charger detection */
INIT_WORK(&di->usb_link_status_work,
ab8500_charger_usb_link_status_work);
@@ -2651,9 +3588,6 @@ static int ab8500_charger_probe(struct platform_device *pdev)
INIT_WORK(&di->detect_usb_type_work,
ab8500_charger_detect_usb_type_work);
- INIT_WORK(&di->usb_state_changed_work,
- ab8500_charger_usb_state_changed_work);
-
/* Init work for checking HW status */
INIT_WORK(&di->check_main_thermal_prot_work,
ab8500_charger_check_main_thermal_prot_work);
@@ -2665,7 +3599,7 @@ static int ab8500_charger_probe(struct platform_device *pdev)
* is a charger connected to avoid erroneous BTEMP_HIGH/LOW
* interrupts during charging
*/
- di->regu = regulator_get(di->dev, "vddadc");
+ di->regu = devm_regulator_get(di->dev, "vddadc");
if (IS_ERR(di->regu)) {
ret = PTR_ERR(di->regu);
dev_err(di->dev, "failed to get vddadc regulator\n");
@@ -2677,21 +3611,25 @@ static int ab8500_charger_probe(struct platform_device *pdev)
ret = ab8500_charger_init_hw_registers(di);
if (ret) {
dev_err(di->dev, "failed to initialize ABB registers\n");
- goto free_regulator;
+ goto free_charger_wq;
}
/* Register AC charger class */
- ret = power_supply_register(di->dev, &di->ac_chg.psy);
- if (ret) {
- dev_err(di->dev, "failed to register AC charger\n");
- goto free_regulator;
+ if (di->ac_chg.enabled) {
+ ret = power_supply_register(di->dev, &di->ac_chg.psy);
+ if (ret) {
+ dev_err(di->dev, "failed to register AC charger\n");
+ goto free_charger_wq;
+ }
}
/* Register USB charger class */
- ret = power_supply_register(di->dev, &di->usb_chg.psy);
- if (ret) {
- dev_err(di->dev, "failed to register USB charger\n");
- goto free_ac;
+ if (di->usb_chg.enabled) {
+ ret = power_supply_register(di->dev, &di->usb_chg.psy);
+ if (ret) {
+ dev_err(di->dev, "failed to register USB charger\n");
+ goto free_ac;
+ }
}
di->usb_phy = usb_get_phy(USB_PHY_TYPE_USB2);
@@ -2708,7 +3646,7 @@ static int ab8500_charger_probe(struct platform_device *pdev)
}
/* Identify the connected charger types during startup */
- charger_status = ab8500_charger_detect_chargers(di);
+ charger_status = ab8500_charger_detect_chargers(di, true);
if (charger_status & AC_PW_CONN) {
di->ac.charger_connected = 1;
di->ac_conn = true;
@@ -2717,7 +3655,6 @@ static int ab8500_charger_probe(struct platform_device *pdev)
}
if (charger_status & USB_PW_CONN) {
- dev_dbg(di->dev, "VBUS Detect during startup\n");
di->vbus_detected = true;
di->vbus_detected_start = true;
queue_work(di->charger_wq,
@@ -2742,6 +3679,25 @@ static int ab8500_charger_probe(struct platform_device *pdev)
platform_set_drvdata(pdev, di);
+ mutex_lock(&di->charger_attached_mutex);
+
+ ch_stat = ab8500_charger_detect_chargers(di, false);
+
+ if ((ch_stat & AC_PW_CONN) == AC_PW_CONN) {
+ if (is_ab8500(di->parent))
+ queue_delayed_work(di->charger_wq,
+ &di->ac_charger_attached_work,
+ HZ);
+ }
+ if ((ch_stat & USB_PW_CONN) == USB_PW_CONN) {
+ if (is_ab8500(di->parent))
+ queue_delayed_work(di->charger_wq,
+ &di->usb_charger_attached_work,
+ HZ);
+ }
+
+ mutex_unlock(&di->charger_attached_mutex);
+
return ret;
free_irq:
@@ -2755,11 +3711,11 @@ free_irq:
put_usb_phy:
usb_put_phy(di->usb_phy);
free_usb:
- power_supply_unregister(&di->usb_chg.psy);
+ if (di->usb_chg.enabled)
+ power_supply_unregister(&di->usb_chg.psy);
free_ac:
- power_supply_unregister(&di->ac_chg.psy);
-free_regulator:
- regulator_put(di->regu);
+ if (di->ac_chg.enabled)
+ power_supply_unregister(&di->ac_chg.psy);
free_charger_wq:
destroy_workqueue(di->charger_wq);
return ret;
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2025-11-09 16:25:06 +0000