1 files changed, 168 insertions, 331 deletions

diff --git a/drivers/pinctrl/pinctrl-coh901.c b/drivers/pinctrl/pinctrl-coh901.c
index 55697a5d748..d182fdd2e71 100644
--- a/drivers/pinctrl/pinctrl-coh901.c
+++ b/drivers/pinctrl/pinctrl-coh901.c
@@ -1,17 +1,13 @@
 /*
  * U300 GPIO module.
  *
- * Copyright (C) 2007-2011 ST-Ericsson AB
+ * Copyright (C) 2007-2012 ST-Ericsson AB
  * License terms: GNU General Public License (GPL) version 2
- * This can driver either of the two basic GPIO cores
- * available in the U300 platforms:
- * COH 901 335   - Used in DB3150 (U300 1.0) and DB3200 (U330 1.0)
  * COH 901 571/3 - Used in DB3210 (U365 2.0) and DB3350 (U335 1.0)
  * Author: Linus Walleij <linus.walleij@linaro.org>
  * Author: Jonas Aaberg <jonas.aberg@stericsson.com>
  */
 #include <linux/module.h>
-#include <linux/irq.h>
 #include <linux/interrupt.h>
 #include <linux/delay.h>
 #include <linux/errno.h>
@@ -20,23 +16,24 @@
 #include <linux/err.h>
 #include <linux/platform_device.h>
 #include <linux/gpio.h>
-#include <linux/list.h>
 #include <linux/slab.h>
 #include <linux/pinctrl/consumer.h>
 #include <linux/pinctrl/pinconf-generic.h>
-#include <mach/gpio-u300.h>
 #include "pinctrl-coh901.h"
 
+#define U300_GPIO_PORT_STRIDE				(0x30)
 /*
- * Register definitions for COH 901 335 variant
+ * Control Register 32bit (R/W)
+ * bit 15-9 (mask 0x0000FE00) contains the number of cores. 8*cores
+ * gives the number of GPIO pins.
+ * bit 8-2  (mask 0x000001FC) contains the core version ID.
  */
-#define U300_335_PORT_STRIDE				(0x1C)
-/* Port X Pin Data Register 32bit, this is both input and output (R/W) */
-#define U300_335_PXPDIR					(0x00)
-#define U300_335_PXPDOR					(0x00)
-/* Port X Pin Config Register 32bit (R/W) */
-#define U300_335_PXPCR					(0x04)
-/* This register layout is the same in both blocks */
+#define U300_GPIO_CR					(0x00)
+#define U300_GPIO_CR_SYNC_SEL_ENABLE			(0x00000002UL)
+#define U300_GPIO_CR_BLOCK_CLKRQ_ENABLE			(0x00000001UL)
+#define U300_GPIO_PXPDIR				(0x04)
+#define U300_GPIO_PXPDOR				(0x08)
+#define U300_GPIO_PXPCR					(0x0C)
 #define U300_GPIO_PXPCR_ALL_PINS_MODE_MASK		(0x0000FFFFUL)
 #define U300_GPIO_PXPCR_PIN_MODE_MASK			(0x00000003UL)
 #define U300_GPIO_PXPCR_PIN_MODE_SHIFT			(0x00000002UL)
@@ -44,66 +41,37 @@
 #define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL	(0x00000001UL)
 #define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_DRAIN	(0x00000002UL)
 #define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_SOURCE	(0x00000003UL)
-/* Port X Interrupt Event Register 32bit (R/W) */
-#define U300_335_PXIEV					(0x08)
-/* Port X Interrupt Enable Register 32bit (R/W) */
-#define U300_335_PXIEN					(0x0C)
-/* Port X Interrupt Force Register 32bit (R/W) */
-#define U300_335_PXIFR					(0x10)
-/* Port X Interrupt Config Register 32bit (R/W) */
-#define U300_335_PXICR					(0x14)
-/* This register layout is the same in both blocks */
+#define U300_GPIO_PXPER					(0x10)
+#define U300_GPIO_PXPER_ALL_PULL_UP_DISABLE_MASK	(0x000000FFUL)
+#define U300_GPIO_PXPER_PULL_UP_DISABLE			(0x00000001UL)
+#define U300_GPIO_PXIEV					(0x14)
+#define U300_GPIO_PXIEN					(0x18)
+#define U300_GPIO_PXIFR					(0x1C)
+#define U300_GPIO_PXICR					(0x20)
 #define U300_GPIO_PXICR_ALL_IRQ_CONFIG_MASK		(0x000000FFUL)
 #define U300_GPIO_PXICR_IRQ_CONFIG_MASK			(0x00000001UL)
 #define U300_GPIO_PXICR_IRQ_CONFIG_FALLING_EDGE		(0x00000000UL)
 #define U300_GPIO_PXICR_IRQ_CONFIG_RISING_EDGE		(0x00000001UL)
-/* Port X Pull-up Enable Register 32bit (R/W) */
-#define U300_335_PXPER					(0x18)
-/* This register layout is the same in both blocks */
-#define U300_GPIO_PXPER_ALL_PULL_UP_DISABLE_MASK	(0x000000FFUL)
-#define U300_GPIO_PXPER_PULL_UP_DISABLE			(0x00000001UL)
-/* Control Register 32bit (R/W) */
-#define U300_335_CR					(0x54)
-#define U300_335_CR_BLOCK_CLOCK_ENABLE			(0x00000001UL)
-
-/*
- * Register definitions for COH 901 571 / 3 variant
- */
-#define U300_571_PORT_STRIDE				(0x30)
-/*
- * Control Register 32bit (R/W)
- * bit 15-9 (mask 0x0000FE00) contains the number of cores. 8*cores
- * gives the number of GPIO pins.
- * bit 8-2  (mask 0x000001FC) contains the core version ID.
- */
-#define U300_571_CR					(0x00)
-#define U300_571_CR_SYNC_SEL_ENABLE			(0x00000002UL)
-#define U300_571_CR_BLOCK_CLKRQ_ENABLE			(0x00000001UL)
-/*
- * These registers have the same layout and function as the corresponding
- * COH 901 335 registers, just at different offset.
- */
-#define U300_571_PXPDIR					(0x04)
-#define U300_571_PXPDOR					(0x08)
-#define U300_571_PXPCR					(0x0C)
-#define U300_571_PXPER					(0x10)
-#define U300_571_PXIEV					(0x14)
-#define U300_571_PXIEN					(0x18)
-#define U300_571_PXIFR					(0x1C)
-#define U300_571_PXICR					(0x20)
 
 /* 8 bits per port, no version has more than 7 ports */
+#define U300_GPIO_NUM_PORTS 7
 #define U300_GPIO_PINS_PER_PORT 8
-#define U300_GPIO_MAX (U300_GPIO_PINS_PER_PORT * 7)
+#define U300_GPIO_MAX (U300_GPIO_PINS_PER_PORT * U300_GPIO_NUM_PORTS)
+
+struct u300_gpio_port {
+	struct u300_gpio *gpio;
+	char name[8];
+	int irq;
+	int number;
+	u8 toggle_edge_mode;
+};
 
 struct u300_gpio {
 	struct gpio_chip chip;
-	struct list_head port_list;
+	struct u300_gpio_port ports[U300_GPIO_NUM_PORTS];
 	struct clk *clk;
-	struct resource *memres;
 	void __iomem *base;
 	struct device *dev;
-	int irq_base;
 	u32 stride;
 	/* Register offsets */
 	u32 pcr;
@@ -115,15 +83,6 @@ struct u300_gpio {
 	u32 iev;
 };
 
-struct u300_gpio_port {
-	struct list_head node;
-	struct u300_gpio *gpio;
-	char name[8];
-	int irq;
-	int number;
-	u8 toggle_edge_mode;
-};
-
 /*
  * Macro to expand to read a specific register found in the "gpio"
  * struct. It requires the struct u300_gpio *gpio variable to exist in
@@ -147,11 +106,6 @@ struct u300_gpio_confdata {
 	int outval;
 };
 
-/* BS335 has seven ports of 8 bits each = GPIO pins 0..55 */
-#define BS335_GPIO_NUM_PORTS 7
-/* BS365 has five ports of 8 bits each = GPIO pins 0..39 */
-#define BS365_GPIO_NUM_PORTS 5
-
 #define U300_FLOATING_INPUT { \
 	.bias_mode = PIN_CONFIG_BIAS_HIGH_IMPEDANCE, \
 	.output = false, \
@@ -172,10 +126,9 @@ struct u300_gpio_confdata {
 	.outval = 1, \
 }
 
-
 /* Initial configuration */
 static const struct __initconst u300_gpio_confdata
-bs335_gpio_config[BS335_GPIO_NUM_PORTS][U300_GPIO_PINS_PER_PORT] = {
+bs335_gpio_config[U300_GPIO_NUM_PORTS][U300_GPIO_PINS_PER_PORT] = {
 	/* Port 0, pins 0-7 */
 	{
 		U300_FLOATING_INPUT,
@@ -255,66 +208,6 @@ bs335_gpio_config[BS335_GPIO_NUM_PORTS][U300_GPIO_PINS_PER_PORT] = {
 	}
 };
 
-static const struct __initconst u300_gpio_confdata
-bs365_gpio_config[BS365_GPIO_NUM_PORTS][U300_GPIO_PINS_PER_PORT] = {
-	/* Port 0, pins 0-7 */
-	{
-		U300_FLOATING_INPUT,
-		U300_OUTPUT_LOW,
-		U300_FLOATING_INPUT,
-		U300_OUTPUT_LOW,
-		U300_OUTPUT_LOW,
-		U300_OUTPUT_LOW,
-		U300_PULL_UP_INPUT,
-		U300_FLOATING_INPUT,
-	},
-	/* Port 1, pins 0-7 */
-	{
-		U300_OUTPUT_LOW,
-		U300_FLOATING_INPUT,
-		U300_OUTPUT_LOW,
-		U300_FLOATING_INPUT,
-		U300_FLOATING_INPUT,
-		U300_OUTPUT_HIGH,
-		U300_OUTPUT_LOW,
-		U300_OUTPUT_LOW,
-	},
-	/* Port 2, pins 0-7 */
-	{
-		U300_FLOATING_INPUT,
-		U300_PULL_UP_INPUT,
-		U300_OUTPUT_LOW,
-		U300_OUTPUT_LOW,
-		U300_PULL_UP_INPUT,
-		U300_PULL_UP_INPUT,
-		U300_PULL_UP_INPUT,
-		U300_PULL_UP_INPUT,
-	},
-	/* Port 3, pins 0-7 */
-	{
-		U300_PULL_UP_INPUT,
-		U300_PULL_UP_INPUT,
-		U300_PULL_UP_INPUT,
-		U300_PULL_UP_INPUT,
-		U300_PULL_UP_INPUT,
-		U300_PULL_UP_INPUT,
-		U300_PULL_UP_INPUT,
-		U300_PULL_UP_INPUT,
-	},
-	/* Port 4, pins 0-7 */
-	{
-		U300_PULL_UP_INPUT,
-		U300_PULL_UP_INPUT,
-		U300_PULL_UP_INPUT,
-		U300_PULL_UP_INPUT,
-		/* These 4 pins doesn't exist on DB3210 */
-		U300_OUTPUT_LOW,
-		U300_OUTPUT_LOW,
-		U300_OUTPUT_LOW,
-		U300_OUTPUT_LOW,
-	}
-};
-
 /**
  * to_u300_gpio() - get the pointer to u300_gpio
  * @chip: the gpio chip member of the structure u300_gpio
@@ -410,16 +303,6 @@ static int u300_gpio_direction_output(struct gpio_chip *chip, unsigned offset,
 	return 0;
 }
 
-static int u300_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
-{
-	struct u300_gpio *gpio = to_u300_gpio(chip);
-	int retirq = gpio->irq_base + offset;
-
-	dev_dbg(gpio->dev, "request IRQ for GPIO %d, return %d\n", offset,
-		retirq);
-	return retirq;
-}
-
 /* Returning -EINVAL means "supported but not available" */
 int u300_gpio_config_get(struct gpio_chip *chip,
 			 unsigned offset,
@@ -438,7 +321,7 @@ int u300_gpio_config_get(struct gpio_chip *chip,
 	drmode &= (U300_GPIO_PXPCR_PIN_MODE_MASK << ((offset & 0x07) << 1));
 	drmode >>= ((offset & 0x07) << 1);
 
-	switch(param) {
+	switch (param) {
 	case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
 		*config = 0;
 		if (biasmode)
@@ -540,7 +423,6 @@ static struct gpio_chip u300_gpio_chip = {
 	.set			= u300_gpio_set,
 	.direction_input	= u300_gpio_direction_input,
 	.direction_output	= u300_gpio_direction_output,
-	.to_irq			= u300_gpio_to_irq,
 };
 
 static void u300_toggle_trigger(struct u300_gpio *gpio, unsigned offset)
@@ -564,9 +446,10 @@ static void u300_toggle_trigger(struct u300_gpio *gpio, unsigned offset)
 
 static int u300_gpio_irq_type(struct irq_data *d, unsigned trigger)
 {
-	struct u300_gpio_port *port = irq_data_get_irq_chip_data(d);
-	struct u300_gpio *gpio = port->gpio;
-	int offset = d->irq - gpio->irq_base;
+	struct gpio_chip *chip = irq_data_get_irq_chip_data(d);
+	struct u300_gpio *gpio = to_u300_gpio(chip);
+	struct u300_gpio_port *port = &gpio->ports[d->hwirq >> 3];
+	int offset = d->hwirq;
 	u32 val;
 
 	if ((trigger & IRQF_TRIGGER_RISING) &&
@@ -600,12 +483,15 @@ static int u300_gpio_irq_type(struct irq_data *d, unsigned trigger)
 
 static void u300_gpio_irq_enable(struct irq_data *d)
 {
-	struct u300_gpio_port *port = irq_data_get_irq_chip_data(d);
-	struct u300_gpio *gpio = port->gpio;
-	int offset = d->irq - gpio->irq_base;
+	struct gpio_chip *chip = irq_data_get_irq_chip_data(d);
+	struct u300_gpio *gpio = to_u300_gpio(chip);
+	struct u300_gpio_port *port = &gpio->ports[d->hwirq >> 3];
+	int offset = d->hwirq;
 	u32 val;
 	unsigned long flags;
 
+	dev_dbg(gpio->dev, "enable IRQ for hwirq %lu on port %s, offset %d\n",
+		 d->hwirq, port->name, offset);
 	local_irq_save(flags);
 	val = readl(U300_PIN_REG(offset, ien));
 	writel(val | U300_PIN_BIT(offset), U300_PIN_REG(offset, ien));
@@ -614,9 +500,9 @@ static void u300_gpio_irq_enable(struct irq_data *d)
 
 static void u300_gpio_irq_disable(struct irq_data *d)
 {
-	struct u300_gpio_port *port = irq_data_get_irq_chip_data(d);
-	struct u300_gpio *gpio = port->gpio;
-	int offset = d->irq - gpio->irq_base;
+	struct gpio_chip *chip = irq_data_get_irq_chip_data(d);
+	struct u300_gpio *gpio = to_u300_gpio(chip);
+	int offset = d->hwirq;
 	u32 val;
 	unsigned long flags;
 
@@ -631,17 +517,19 @@ static struct irq_chip u300_gpio_irqchip = {
 	.irq_enable		= u300_gpio_irq_enable,
 	.irq_disable		= u300_gpio_irq_disable,
 	.irq_set_type		= u300_gpio_irq_type,
-
 };
 
 static void u300_gpio_irq_handler(unsigned irq, struct irq_desc *desc)
 {
-	struct u300_gpio_port *port = irq_get_handler_data(irq);
-	struct u300_gpio *gpio = port->gpio;
+	struct irq_chip *parent_chip = irq_get_chip(irq);
+	struct gpio_chip *chip = irq_get_handler_data(irq);
+	struct u300_gpio *gpio = to_u300_gpio(chip);
+	struct u300_gpio_port *port = &gpio->ports[irq - chip->base];
 	int pinoffset = port->number << 3; /* get the right stride */
 	unsigned long val;
 
-	desc->irq_data.chip->irq_ack(&desc->irq_data);
+	chained_irq_enter(parent_chip, desc);
+
 	/* Read event register */
 	val = readl(U300_PIN_REG(pinoffset, iev));
 	/* Mask relevant bits */
@@ -654,9 +542,8 @@ static void u300_gpio_irq_handler(unsigned irq, struct irq_desc *desc)
 		int irqoffset;
 
 		for_each_set_bit(irqoffset, &val, U300_GPIO_PINS_PER_PORT) {
-			int pin_irq = gpio->irq_base + (port->number << 3)
-				+ irqoffset;
 			int offset = pinoffset + irqoffset;
+			int pin_irq = irq_find_mapping(chip->irqdomain, offset);
 
 			dev_dbg(gpio->dev, "GPIO IRQ %d on pin %d\n",
 				pin_irq, offset);
@@ -670,7 +557,7 @@ static void u300_gpio_irq_handler(unsigned irq, struct irq_desc *desc)
 		}
 	}
 
-	desc->irq_data.chip->irq_unmask(&desc->irq_data);
+	chained_irq_exit(parent_chip, desc);
 }
 
 static void __init u300_gpio_init_pin(struct u300_gpio *gpio,
@@ -705,254 +592,204 @@ static void __init u300_gpio_init_pin(struct u300_gpio *gpio,
 	}
 }
 
-static void __init u300_gpio_init_coh901571(struct u300_gpio *gpio,
-				     struct u300_gpio_platform *plat)
+static void __init u300_gpio_init_coh901571(struct u300_gpio *gpio)
 {
 	int i, j;
 
 	/* Write default config and values to all pins */
-	for (i = 0; i < plat->ports; i++) {
+	for (i = 0; i < U300_GPIO_NUM_PORTS; i++) {
 		for (j = 0; j < 8; j++) {
 			const struct u300_gpio_confdata *conf;
 			int offset = (i*8) + j;
 
-			if (plat->variant == U300_GPIO_COH901571_3_BS335)
-				conf = &bs335_gpio_config[i][j];
-			else if (plat->variant == U300_GPIO_COH901571_3_BS365)
-				conf = &bs365_gpio_config[i][j];
-			else
-				break;
-
+			conf = &bs335_gpio_config[i][j];
 			u300_gpio_init_pin(gpio, offset, conf);
 		}
 	}
 }
 
-static inline void u300_gpio_free_ports(struct u300_gpio *gpio)
-{
-	struct u300_gpio_port *port;
-	struct list_head *p, *n;
+/*
+ * Here we map a GPIO in the local gpio_chip pin space to a pin in
+ * the local pinctrl pin space. The pin controller used is
+ * pinctrl-u300.
+ */
+struct coh901_pinpair {
+	unsigned int offset;
+	unsigned int pin_base;
+};
 
-	list_for_each_safe(p, n, &gpio->port_list) {
-		port = list_entry(p, struct u300_gpio_port, node);
-		list_del(&port->node);
-		kfree(port);
-	}
-}
+#define COH901_PINRANGE(a, b) { .offset = a, .pin_base = b }
+
+static struct coh901_pinpair coh901_pintable[] = {
+	COH901_PINRANGE(10, 426),
+	COH901_PINRANGE(11, 180),
+	COH901_PINRANGE(12, 165), /* MS/MMC card insertion */
+	COH901_PINRANGE(13, 179),
+	COH901_PINRANGE(14, 178),
+	COH901_PINRANGE(16, 194),
+	COH901_PINRANGE(17, 193),
+	COH901_PINRANGE(18, 192),
+	COH901_PINRANGE(19, 191),
+	COH901_PINRANGE(20, 186),
+	COH901_PINRANGE(21, 185),
+	COH901_PINRANGE(22, 184),
+	COH901_PINRANGE(23, 183),
+	COH901_PINRANGE(24, 182),
+	COH901_PINRANGE(25, 181),
+};
 
 static int __init u300_gpio_probe(struct platform_device *pdev)
 {
-	struct u300_gpio_platform *plat = dev_get_platdata(&pdev->dev);
 	struct u300_gpio *gpio;
+	struct resource *memres;
 	int err = 0;
 	int portno;
 	u32 val;
 	u32 ifr;
 	int i;
 
-	gpio = kzalloc(sizeof(struct u300_gpio), GFP_KERNEL);
-	if (gpio == NULL) {
-		dev_err(&pdev->dev, "failed to allocate memory\n");
+	gpio = devm_kzalloc(&pdev->dev, sizeof(struct u300_gpio), GFP_KERNEL);
+	if (gpio == NULL)
 		return -ENOMEM;
-	}
 
 	gpio->chip = u300_gpio_chip;
-	gpio->chip.ngpio = plat->ports * U300_GPIO_PINS_PER_PORT;
-	gpio->irq_base = plat->gpio_irq_base;
+	gpio->chip.ngpio = U300_GPIO_NUM_PORTS * U300_GPIO_PINS_PER_PORT;
 	gpio->chip.dev = &pdev->dev;
-	gpio->chip.base = plat->gpio_base;
+	gpio->chip.base = 0;
 	gpio->dev = &pdev->dev;
 
-	/* Get GPIO clock */
-	gpio->clk = clk_get(gpio->dev, NULL);
+	memres = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	gpio->base = devm_ioremap_resource(&pdev->dev, memres);
+	if (IS_ERR(gpio->base))
+		return PTR_ERR(gpio->base);
+
+	gpio->clk = devm_clk_get(gpio->dev, NULL);
 	if (IS_ERR(gpio->clk)) {
 		err = PTR_ERR(gpio->clk);
 		dev_err(gpio->dev, "could not get GPIO clock\n");
-		goto err_no_clk;
+		return err;
 	}
-	err = clk_enable(gpio->clk);
+
+	err = clk_prepare_enable(gpio->clk);
 	if (err) {
 		dev_err(gpio->dev, "could not enable GPIO clock\n");
-		goto err_no_clk_enable;
-	}
-
-	gpio->memres = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	if (!gpio->memres) {
-		dev_err(gpio->dev, "could not get GPIO memory resource\n");
-		err = -ENODEV;
-		goto err_no_resource;
-	}
-
-	if (!request_mem_region(gpio->memres->start,
-				resource_size(gpio->memres),
-				"GPIO Controller")) {
-		err = -ENODEV;
-		goto err_no_ioregion;
+		return err;
 	}
 
-	gpio->base = ioremap(gpio->memres->start, resource_size(gpio->memres));
-	if (!gpio->base) {
-		err = -ENOMEM;
-		goto err_no_ioremap;
+	dev_info(gpio->dev,
+		 "initializing GPIO Controller COH 901 571/3\n");
+	gpio->stride = U300_GPIO_PORT_STRIDE;
+	gpio->pcr = U300_GPIO_PXPCR;
+	gpio->dor = U300_GPIO_PXPDOR;
+	gpio->dir = U300_GPIO_PXPDIR;
+	gpio->per = U300_GPIO_PXPER;
+	gpio->icr = U300_GPIO_PXICR;
+	gpio->ien = U300_GPIO_PXIEN;
+	gpio->iev = U300_GPIO_PXIEV;
+	ifr = U300_GPIO_PXIFR;
+
+	val = readl(gpio->base + U300_GPIO_CR);
+	dev_info(gpio->dev, "COH901571/3 block version: %d, " \
+		 "number of cores: %d totalling %d pins\n",
+		 ((val & 0x000001FC) >> 2),
+		 ((val & 0x0000FE00) >> 9),
+		 ((val & 0x0000FE00) >> 9) * 8);
+	writel(U300_GPIO_CR_BLOCK_CLKRQ_ENABLE,
+	       gpio->base + U300_GPIO_CR);
+	u300_gpio_init_coh901571(gpio);
+
+#ifdef CONFIG_OF_GPIO
+	gpio->chip.of_node = pdev->dev.of_node;
+#endif
+	err = gpiochip_add(&gpio->chip);
+	if (err) {
+		dev_err(gpio->dev, "unable to add gpiochip: %d\n", err);
+		goto err_no_chip;
 	}
 
-	if (plat->variant == U300_GPIO_COH901335) {
-		dev_info(gpio->dev,
-			 "initializing GPIO Controller COH 901 335\n");
-		gpio->stride = U300_335_PORT_STRIDE;
-		gpio->pcr = U300_335_PXPCR;
-		gpio->dor = U300_335_PXPDOR;
-		gpio->dir = U300_335_PXPDIR;
-		gpio->per = U300_335_PXPER;
-		gpio->icr = U300_335_PXICR;
-		gpio->ien = U300_335_PXIEN;
-		gpio->iev = U300_335_PXIEV;
-		ifr = U300_335_PXIFR;
-
-		/* Turn on the GPIO block */
-		writel(U300_335_CR_BLOCK_CLOCK_ENABLE,
-		       gpio->base + U300_335_CR);
-	} else if (plat->variant == U300_GPIO_COH901571_3_BS335 ||
-		   plat->variant == U300_GPIO_COH901571_3_BS365) {
-		dev_info(gpio->dev,
-			 "initializing GPIO Controller COH 901 571/3\n");
-		gpio->stride = U300_571_PORT_STRIDE;
-		gpio->pcr = U300_571_PXPCR;
-		gpio->dor = U300_571_PXPDOR;
-		gpio->dir = U300_571_PXPDIR;
-		gpio->per = U300_571_PXPER;
-		gpio->icr = U300_571_PXICR;
-		gpio->ien = U300_571_PXIEN;
-		gpio->iev = U300_571_PXIEV;
-		ifr = U300_571_PXIFR;
-
-		val = readl(gpio->base + U300_571_CR);
-		dev_info(gpio->dev, "COH901571/3 block version: %d, " \
-			 "number of cores: %d totalling %d pins\n",
-			 ((val & 0x000001FC) >> 2),
-			 ((val & 0x0000FE00) >> 9),
-			 ((val & 0x0000FE00) >> 9) * 8);
-		writel(U300_571_CR_BLOCK_CLKRQ_ENABLE,
-		       gpio->base + U300_571_CR);
-		u300_gpio_init_coh901571(gpio, plat);
-	} else {
-		dev_err(gpio->dev, "unknown block variant\n");
-		err = -ENODEV;
-		goto err_unknown_variant;
+	err = gpiochip_irqchip_add(&gpio->chip,
+				   &u300_gpio_irqchip,
+				   0,
+				   handle_simple_irq,
+				   IRQ_TYPE_EDGE_FALLING);
+	if (err) {
+		dev_err(gpio->dev, "no GPIO irqchip\n");
+		goto err_no_irqchip;
 	}
 
 	/* Add each port with its IRQ separately */
-	INIT_LIST_HEAD(&gpio->port_list);
-	for (portno = 0 ; portno < plat->ports; portno++) {
-		struct u300_gpio_port *port =
-			kmalloc(sizeof(struct u300_gpio_port), GFP_KERNEL);
-
-		if (!port) {
-			dev_err(gpio->dev, "out of memory\n");
-			err = -ENOMEM;
-			goto err_no_port;
-		}
+	for (portno = 0 ; portno < U300_GPIO_NUM_PORTS; portno++) {
+		struct u300_gpio_port *port = &gpio->ports[portno];
 
 		snprintf(port->name, 8, "gpio%d", portno);
 		port->number = portno;
 		port->gpio = gpio;
 
-		port->irq = platform_get_irq_byname(pdev,
-						    port->name);
-
-		dev_dbg(gpio->dev, "register IRQ %d for %s\n", port->irq,
-			port->name);
+		port->irq = platform_get_irq(pdev, portno);
 
-		irq_set_chained_handler(port->irq, u300_gpio_irq_handler);
-		irq_set_handler_data(port->irq, port);
-
-		/* For each GPIO pin set the unique IRQ handler */
-		for (i = 0; i < U300_GPIO_PINS_PER_PORT; i++) {
-			int irqno = gpio->irq_base + (portno << 3) + i;
-
-			dev_dbg(gpio->dev, "handler for IRQ %d on %s\n",
-				irqno, port->name);
-			irq_set_chip_and_handler(irqno, &u300_gpio_irqchip,
-						 handle_simple_irq);
-			set_irq_flags(irqno, IRQF_VALID);
-			irq_set_chip_data(irqno, port);
-		}
+		gpiochip_set_chained_irqchip(&gpio->chip,
+					     &u300_gpio_irqchip,
+					     port->irq,
+					     u300_gpio_irq_handler);
 
 		/* Turns off irq force (test register) for this port */
 		writel(0x0, gpio->base + portno * gpio->stride + ifr);
-
-		list_add_tail(&port->node, &gpio->port_list);
 	}
 	dev_dbg(gpio->dev, "initialized %d GPIO ports\n", portno);
 
-	err = gpiochip_add(&gpio->chip);
-	if (err) {
-		dev_err(gpio->dev, "unable to add gpiochip: %d\n", err);
-		goto err_no_chip;
-	}
+	/*
+	 * Add pinctrl pin ranges, the pin controller must be registered
+	 * at this point
+	 */
+	for (i = 0; i < ARRAY_SIZE(coh901_pintable); i++) {
+		struct coh901_pinpair *p = &coh901_pintable[i];
 
-	/* Spawn pin controller device as child of the GPIO, pass gpio chip */
-	plat->pinctrl_device->dev.platform_data = &gpio->chip;
-	err = platform_device_register(plat->pinctrl_device);
-	if (err)
-		goto err_no_pinctrl;
+		err = gpiochip_add_pin_range(&gpio->chip, "pinctrl-u300",
+					     p->offset, p->pin_base, 1);
+		if (err)
+			goto err_no_range;
+	}
 
 	platform_set_drvdata(pdev, gpio);
 
 	return 0;
 
-err_no_pinctrl:
-	err = gpiochip_remove(&gpio->chip);
+err_no_range:
+err_no_irqchip:
+	if (gpiochip_remove(&gpio->chip))
+		dev_err(&pdev->dev, "failed to remove gpio chip\n");
 err_no_chip:
-err_no_port:
-	u300_gpio_free_ports(gpio);
-err_unknown_variant:
-	iounmap(gpio->base);
-err_no_ioremap:
-	release_mem_region(gpio->memres->start, resource_size(gpio->memres));
-err_no_ioregion:
-err_no_resource:
-	clk_disable(gpio->clk);
-err_no_clk_enable:
-	clk_put(gpio->clk);
-err_no_clk:
-	kfree(gpio);
-	dev_info(&pdev->dev, "module ERROR:%d\n", err);
+	clk_disable_unprepare(gpio->clk);
+	dev_err(&pdev->dev, "module ERROR:%d\n", err);
 	return err;
 }
 
 static int __exit u300_gpio_remove(struct platform_device *pdev)
 {
-	struct u300_gpio_platform *plat = dev_get_platdata(&pdev->dev);
 	struct u300_gpio *gpio = platform_get_drvdata(pdev);
 	int err;
 
 	/* Turn off the GPIO block */
-	if (plat->variant == U300_GPIO_COH901335)
-		writel(0x00000000U, gpio->base + U300_335_CR);
-	if (plat->variant == U300_GPIO_COH901571_3_BS335 ||
-	    plat->variant == U300_GPIO_COH901571_3_BS365)
-		writel(0x00000000U, gpio->base + U300_571_CR);
+	writel(0x00000000U, gpio->base + U300_GPIO_CR);
 
 	err = gpiochip_remove(&gpio->chip);
 	if (err < 0) {
 		dev_err(gpio->dev, "unable to remove gpiochip: %d\n", err);
 		return err;
 	}
-	u300_gpio_free_ports(gpio);
-	iounmap(gpio->base);
-	release_mem_region(gpio->memres->start,
-			   resource_size(gpio->memres));
-	clk_disable(gpio->clk);
-	clk_put(gpio->clk);
-	platform_set_drvdata(pdev, NULL);
-	kfree(gpio);
+	clk_disable_unprepare(gpio->clk);
 	return 0;
 }
 
+static const struct of_device_id u300_gpio_match[] = {
+	{ .compatible = "stericsson,gpio-coh901" },
+	{},
+};
+
 static struct platform_driver u300_gpio_driver = {
 	.driver		= {
 		.name	= "u300-gpio",
+		.of_match_table = u300_gpio_match,
 	},
 	.remove		= __exit_p(u300_gpio_remove),
 };