diff options
Diffstat (limited to 'drivers/net/wireless/iwlwifi/iwl-csr.h')
| -rw-r--r-- | drivers/net/wireless/iwlwifi/iwl-csr.h | 373 |
1 files changed, 305 insertions, 68 deletions
diff --git a/drivers/net/wireless/iwlwifi/iwl-csr.h b/drivers/net/wireless/iwlwifi/iwl-csr.h index f34ede44ed1..fe129c94ae3 100644 --- a/drivers/net/wireless/iwlwifi/iwl-csr.h +++ b/drivers/net/wireless/iwlwifi/iwl-csr.h @@ -5,7 +5,7 @@ * * GPL LICENSE SUMMARY * - * Copyright(c) 2005 - 2008 Intel Corporation. All rights reserved. + * Copyright(c) 2005 - 2014 Intel Corporation. All rights reserved. * * This program is free software; you can redistribute it and/or modify * it under the terms of version 2 of the GNU General Public License as @@ -22,7 +22,7 @@ * USA * * The full GNU General Public License is included in this distribution - * in the file called LICENSE.GPL. + * in the file called COPYING. * * Contact Information: * Intel Linux Wireless <ilw@linux.intel.com> @@ -30,7 +30,7 @@ * * BSD LICENSE * - * Copyright(c) 2005 - 2008 Intel Corporation. All rights reserved. + * Copyright(c) 2005 - 2014 Intel Corporation. All rights reserved. * All rights reserved. * * Redistribution and use in source and binary forms, with or without @@ -62,11 +62,28 @@ *****************************************************************************/ #ifndef __iwl_csr_h__ #define __iwl_csr_h__ -/*=== CSR (control and status registers) ===*/ +/* + * CSR (control and status registers) + * + * CSR registers are mapped directly into PCI bus space, and are accessible + * whenever platform supplies power to device, even when device is in + * low power states due to driver-invoked device resets + * (e.g. CSR_RESET_REG_FLAG_SW_RESET) or uCode-driven power-saving modes. + * + * Use iwl_write32() and iwl_read32() family to access these registers; + * these provide simple PCI bus access, without waking up the MAC. + * Do not use iwl_write_direct32() family for these registers; + * no need to "grab nic access" via CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ. + * The MAC (uCode processor, etc.) does not need to be powered up for accessing + * the CSR registers. + * + * NOTE: Device does need to be awake in order to read this memory + * via CSR_EEPROM and CSR_OTP registers + */ #define CSR_BASE (0x000) #define CSR_HW_IF_CONFIG_REG (CSR_BASE+0x000) /* hardware interface config */ -#define CSR_INT_COALESCING (CSR_BASE+0x004) /* accum ints, 32-usec units */ +#define CSR_INT_COALESCING (CSR_BASE+0x004) /* accum ints, 32-usec units */ #define CSR_INT (CSR_BASE+0x008) /* host interrupt status/ack */ #define CSR_INT_MASK (CSR_BASE+0x00c) /* host interrupt enable */ #define CSR_FH_INT_STATUS (CSR_BASE+0x010) /* busmaster int status/ack*/ @@ -74,71 +91,111 @@ #define CSR_RESET (CSR_BASE+0x020) /* busmaster enable, NMI, etc*/ #define CSR_GP_CNTRL (CSR_BASE+0x024) +/* 2nd byte of CSR_INT_COALESCING, not accessible via iwl_write32()! */ +#define CSR_INT_PERIODIC_REG (CSR_BASE+0x005) + /* * Hardware revision info * Bit fields: - * 31-8: Reserved - * 7-4: Type of device: 0x0 = 4965, 0xd = 3945 + * 31-16: Reserved + * 15-4: Type of device: see CSR_HW_REV_TYPE_xxx definitions * 3-2: Revision step: 0 = A, 1 = B, 2 = C, 3 = D - * 1-0: "Dash" value, as in A-1, etc. - * - * NOTE: Revision step affects calculation of CCK txpower for 4965. + * 1-0: "Dash" (-) value, as in A-1, etc. */ #define CSR_HW_REV (CSR_BASE+0x028) -/* EEPROM reads */ +/* + * EEPROM and OTP (one-time-programmable) memory reads + * + * NOTE: Device must be awake, initialized via apm_ops.init(), + * in order to read. + */ #define CSR_EEPROM_REG (CSR_BASE+0x02c) #define CSR_EEPROM_GP (CSR_BASE+0x030) +#define CSR_OTP_GP_REG (CSR_BASE+0x034) + #define CSR_GIO_REG (CSR_BASE+0x03C) -#define CSR_GP_UCODE (CSR_BASE+0x044) +#define CSR_GP_UCODE_REG (CSR_BASE+0x048) +#define CSR_GP_DRIVER_REG (CSR_BASE+0x050) + +/* + * UCODE-DRIVER GP (general purpose) mailbox registers. + * SET/CLR registers set/clear bit(s) if "1" is written. + */ #define CSR_UCODE_DRV_GP1 (CSR_BASE+0x054) #define CSR_UCODE_DRV_GP1_SET (CSR_BASE+0x058) #define CSR_UCODE_DRV_GP1_CLR (CSR_BASE+0x05c) #define CSR_UCODE_DRV_GP2 (CSR_BASE+0x060) + #define CSR_LED_REG (CSR_BASE+0x094) +#define CSR_DRAM_INT_TBL_REG (CSR_BASE+0x0A0) +#define CSR_MAC_SHADOW_REG_CTRL (CSR_BASE+0x0A8) /* 6000 and up */ + + +/* GIO Chicken Bits (PCI Express bus link power management) */ #define CSR_GIO_CHICKEN_BITS (CSR_BASE+0x100) /* Analog phase-lock-loop configuration */ #define CSR_ANA_PLL_CFG (CSR_BASE+0x20c) + /* - * Indicates hardware rev, to determine CCK backoff for txpower calculation. + * CSR HW resources monitor registers + */ +#define CSR_MONITOR_CFG_REG (CSR_BASE+0x214) +#define CSR_MONITOR_STATUS_REG (CSR_BASE+0x228) +#define CSR_MONITOR_XTAL_RESOURCES (0x00000010) + +/* + * CSR Hardware Revision Workaround Register. Indicates hardware rev; + * "step" determines CCK backoff for txpower calculation. Used for 4965 only. + * See also CSR_HW_REV register. * Bit fields: * 3-2: 0 = A, 1 = B, 2 = C, 3 = D step + * 1-0: "Dash" (-) value, as in C-1, etc. */ -#define CSR_HW_REV_WA_REG (CSR_BASE+0x22C) -#define CSR_DBG_HPET_MEM_REG (CSR_BASE+0x240) +#define CSR_HW_REV_WA_REG (CSR_BASE+0x22C) + +#define CSR_DBG_HPET_MEM_REG (CSR_BASE+0x240) +#define CSR_DBG_LINK_PWR_MGMT_REG (CSR_BASE+0x250) /* Bits for CSR_HW_IF_CONFIG_REG */ -#define CSR49_HW_IF_CONFIG_REG_BIT_4965_R (0x00000010) -#define CSR_HW_IF_CONFIG_REG_MSK_BOARD_VER (0x00000C00) -#define CSR_HW_IF_CONFIG_REG_BIT_MAC_SI (0x00000100) +#define CSR_HW_IF_CONFIG_REG_MSK_MAC_DASH (0x00000003) +#define CSR_HW_IF_CONFIG_REG_MSK_MAC_STEP (0x0000000C) +#define CSR_HW_IF_CONFIG_REG_MSK_BOARD_VER (0x000000C0) +#define CSR_HW_IF_CONFIG_REG_BIT_MAC_SI (0x00000100) #define CSR_HW_IF_CONFIG_REG_BIT_RADIO_SI (0x00000200) - -#define CSR39_HW_IF_CONFIG_REG_BIT_3945_MB (0x00000100) -#define CSR39_HW_IF_CONFIG_REG_BIT_3945_MM (0x00000200) -#define CSR39_HW_IF_CONFIG_REG_BIT_SKU_MRC (0x00000400) -#define CSR39_HW_IF_CONFIG_REG_BIT_BOARD_TYPE (0x00000800) -#define CSR39_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_A (0x00000000) -#define CSR39_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_B (0x00001000) - -#define CSR_HW_IF_CONFIG_REG_BIT_HAP_WAKE_L1A (0x00080000) -#define CSR_HW_IF_CONFIG_REG_BIT_EEPROM_OWN_SEM (0x00200000) -#define CSR_HW_IF_CONFIG_REG_BIT_PCI_OWN_SEM (0x00400000) -#define CSR_HW_IF_CONFIG_REG_BIT_ME_OWN (0x02000000) -#define CSR_HW_IF_CONFIG_REG_BIT_WAKE_ME (0x08000000) - +#define CSR_HW_IF_CONFIG_REG_MSK_PHY_TYPE (0x00000C00) +#define CSR_HW_IF_CONFIG_REG_MSK_PHY_DASH (0x00003000) +#define CSR_HW_IF_CONFIG_REG_MSK_PHY_STEP (0x0000C000) + +#define CSR_HW_IF_CONFIG_REG_POS_MAC_DASH (0) +#define CSR_HW_IF_CONFIG_REG_POS_MAC_STEP (2) +#define CSR_HW_IF_CONFIG_REG_POS_BOARD_VER (6) +#define CSR_HW_IF_CONFIG_REG_POS_PHY_TYPE (10) +#define CSR_HW_IF_CONFIG_REG_POS_PHY_DASH (12) +#define CSR_HW_IF_CONFIG_REG_POS_PHY_STEP (14) + +#define CSR_HW_IF_CONFIG_REG_BIT_HAP_WAKE_L1A (0x00080000) +#define CSR_HW_IF_CONFIG_REG_BIT_EEPROM_OWN_SEM (0x00200000) +#define CSR_HW_IF_CONFIG_REG_BIT_NIC_READY (0x00400000) /* PCI_OWN_SEM */ +#define CSR_HW_IF_CONFIG_REG_BIT_NIC_PREPARE_DONE (0x02000000) /* ME_OWN */ +#define CSR_HW_IF_CONFIG_REG_PREPARE (0x08000000) /* WAKE_ME */ +#define CSR_HW_IF_CONFIG_REG_PERSIST_MODE (0x40000000) /* PERSISTENCE */ + +#define CSR_INT_PERIODIC_DIS (0x00) /* disable periodic int*/ +#define CSR_INT_PERIODIC_ENA (0xFF) /* 255*32 usec ~ 8 msec*/ /* interrupt flags in INTA, set by uCode or hardware (e.g. dma), * acknowledged (reset) by host writing "1" to flagged bits. */ #define CSR_INT_BIT_FH_RX (1 << 31) /* Rx DMA, cmd responses, FH_INT[17:16] */ #define CSR_INT_BIT_HW_ERR (1 << 29) /* DMA hardware error FH_INT[31] */ -#define CSR_INT_BIT_DNLD (1 << 28) /* uCode Download */ +#define CSR_INT_BIT_RX_PERIODIC (1 << 28) /* Rx periodic */ #define CSR_INT_BIT_FH_TX (1 << 27) /* Tx DMA FH_INT[1:0] */ #define CSR_INT_BIT_SCD (1 << 26) /* TXQ pointer advanced */ #define CSR_INT_BIT_SW_ERR (1 << 25) /* uCode error */ #define CSR_INT_BIT_RF_KILL (1 << 7) /* HW RFKILL switch GP_CNTRL[27] toggled */ #define CSR_INT_BIT_CT_KILL (1 << 6) /* Critical temp (chip too hot) rfkill */ -#define CSR_INT_BIT_SW_RX (1 << 3) /* Rx, command responses, 3945 */ +#define CSR_INT_BIT_SW_RX (1 << 3) /* Rx, command responses */ #define CSR_INT_BIT_WAKEUP (1 << 1) /* NIC controller waking up (pwr mgmt) */ #define CSR_INT_BIT_ALIVE (1 << 0) /* uCode interrupts once it initializes */ @@ -149,34 +206,23 @@ CSR_INT_BIT_RF_KILL | \ CSR_INT_BIT_SW_RX | \ CSR_INT_BIT_WAKEUP | \ - CSR_INT_BIT_ALIVE) + CSR_INT_BIT_ALIVE | \ + CSR_INT_BIT_RX_PERIODIC) /* interrupt flags in FH (flow handler) (PCI busmaster DMA) */ #define CSR_FH_INT_BIT_ERR (1 << 31) /* Error */ #define CSR_FH_INT_BIT_HI_PRIOR (1 << 30) /* High priority Rx, bypass coalescing */ -#define CSR39_FH_INT_BIT_RX_CHNL2 (1 << 18) /* Rx channel 2 (3945 only) */ #define CSR_FH_INT_BIT_RX_CHNL1 (1 << 17) /* Rx channel 1 */ #define CSR_FH_INT_BIT_RX_CHNL0 (1 << 16) /* Rx channel 0 */ -#define CSR39_FH_INT_BIT_TX_CHNL6 (1 << 6) /* Tx channel 6 (3945 only) */ #define CSR_FH_INT_BIT_TX_CHNL1 (1 << 1) /* Tx channel 1 */ #define CSR_FH_INT_BIT_TX_CHNL0 (1 << 0) /* Tx channel 0 */ -#define CSR39_FH_INT_RX_MASK (CSR_FH_INT_BIT_HI_PRIOR | \ - CSR39_FH_INT_BIT_RX_CHNL2 | \ - CSR_FH_INT_BIT_RX_CHNL1 | \ - CSR_FH_INT_BIT_RX_CHNL0) - +#define CSR_FH_INT_RX_MASK (CSR_FH_INT_BIT_HI_PRIOR | \ + CSR_FH_INT_BIT_RX_CHNL1 | \ + CSR_FH_INT_BIT_RX_CHNL0) -#define CSR39_FH_INT_TX_MASK (CSR39_FH_INT_BIT_TX_CHNL6 | \ - CSR_FH_INT_BIT_TX_CHNL1 | \ - CSR_FH_INT_BIT_TX_CHNL0) - -#define CSR49_FH_INT_RX_MASK (CSR_FH_INT_BIT_HI_PRIOR | \ - CSR_FH_INT_BIT_RX_CHNL1 | \ - CSR_FH_INT_BIT_RX_CHNL0) - -#define CSR49_FH_INT_TX_MASK (CSR_FH_INT_BIT_TX_CHNL1 | \ - CSR_FH_INT_BIT_TX_CHNL0) +#define CSR_FH_INT_TX_MASK (CSR_FH_INT_BIT_TX_CHNL1 | \ + CSR_FH_INT_BIT_TX_CHNL0) /* GPIO */ #define CSR_GPIO_IN_BIT_AUX_POWER (0x00000200) @@ -189,12 +235,52 @@ #define CSR_RESET_REG_FLAG_SW_RESET (0x00000080) #define CSR_RESET_REG_FLAG_MASTER_DISABLED (0x00000100) #define CSR_RESET_REG_FLAG_STOP_MASTER (0x00000200) +#define CSR_RESET_LINK_PWR_MGMT_DISABLED (0x80000000) -/* GP (general purpose) CONTROL */ +/* + * GP (general purpose) CONTROL REGISTER + * Bit fields: + * 27: HW_RF_KILL_SW + * Indicates state of (platform's) hardware RF-Kill switch + * 26-24: POWER_SAVE_TYPE + * Indicates current power-saving mode: + * 000 -- No power saving + * 001 -- MAC power-down + * 010 -- PHY (radio) power-down + * 011 -- Error + * 10: XTAL ON request + * 9-6: SYS_CONFIG + * Indicates current system configuration, reflecting pins on chip + * as forced high/low by device circuit board. + * 4: GOING_TO_SLEEP + * Indicates MAC is entering a power-saving sleep power-down. + * Not a good time to access device-internal resources. + * 3: MAC_ACCESS_REQ + * Host sets this to request and maintain MAC wakeup, to allow host + * access to device-internal resources. Host must wait for + * MAC_CLOCK_READY (and !GOING_TO_SLEEP) before accessing non-CSR + * device registers. + * 2: INIT_DONE + * Host sets this to put device into fully operational D0 power mode. + * Host resets this after SW_RESET to put device into low power mode. + * 0: MAC_CLOCK_READY + * Indicates MAC (ucode processor, etc.) is powered up and can run. + * Internal resources are accessible. + * NOTE: This does not indicate that the processor is actually running. + * NOTE: This does not indicate that device has completed + * init or post-power-down restore of internal SRAM memory. + * Use CSR_UCODE_DRV_GP1_BIT_MAC_SLEEP as indication that + * SRAM is restored and uCode is in normal operation mode. + * Later devices (5xxx/6xxx/1xxx) use non-volatile SRAM, and + * do not need to save/restore it. + * NOTE: After device reset, this bit remains "0" until host sets + * INIT_DONE + */ #define CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY (0x00000001) #define CSR_GP_CNTRL_REG_FLAG_INIT_DONE (0x00000004) #define CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ (0x00000008) #define CSR_GP_CNTRL_REG_FLAG_GOING_TO_SLEEP (0x00000010) +#define CSR_GP_CNTRL_REG_FLAG_XTAL_ON (0x00000400) #define CSR_GP_CNTRL_REG_VAL_MAC_ACCESS_EN (0x00000001) @@ -204,14 +290,26 @@ /* HW REV */ -#define CSR_HW_REV_TYPE_MSK (0x00000F0) -#define CSR_HW_REV_TYPE_3945 (0x00000D0) -#define CSR_HW_REV_TYPE_4965 (0x0000000) +#define CSR_HW_REV_DASH(_val) (((_val) & 0x0000003) >> 0) +#define CSR_HW_REV_STEP(_val) (((_val) & 0x000000C) >> 2) + +#define CSR_HW_REV_TYPE_MSK (0x000FFF0) #define CSR_HW_REV_TYPE_5300 (0x0000020) #define CSR_HW_REV_TYPE_5350 (0x0000030) #define CSR_HW_REV_TYPE_5100 (0x0000050) #define CSR_HW_REV_TYPE_5150 (0x0000040) -#define CSR_HW_REV_TYPE_NONE (0x00000F0) +#define CSR_HW_REV_TYPE_1000 (0x0000060) +#define CSR_HW_REV_TYPE_6x00 (0x0000070) +#define CSR_HW_REV_TYPE_6x50 (0x0000080) +#define CSR_HW_REV_TYPE_6150 (0x0000084) +#define CSR_HW_REV_TYPE_6x05 (0x00000B0) +#define CSR_HW_REV_TYPE_6x30 CSR_HW_REV_TYPE_6x05 +#define CSR_HW_REV_TYPE_6x35 CSR_HW_REV_TYPE_6x05 +#define CSR_HW_REV_TYPE_2x30 (0x00000C0) +#define CSR_HW_REV_TYPE_2x00 (0x0000100) +#define CSR_HW_REV_TYPE_105 (0x0000110) +#define CSR_HW_REV_TYPE_135 (0x0000120) +#define CSR_HW_REV_TYPE_NONE (0x00001F0) /* EEPROM REG */ #define CSR_EEPROM_REG_READ_VALID_MSK (0x00000001) @@ -220,36 +318,138 @@ #define CSR_EEPROM_REG_MSK_DATA (0xFFFF0000) /* EEPROM GP */ -#define CSR_EEPROM_GP_VALID_MSK (0x00000006) -#define CSR_EEPROM_GP_BAD_SIGNATURE (0x00000000) +#define CSR_EEPROM_GP_VALID_MSK (0x00000007) /* signature */ #define CSR_EEPROM_GP_IF_OWNER_MSK (0x00000180) +#define CSR_EEPROM_GP_BAD_SIGNATURE_BOTH_EEP_AND_OTP (0x00000000) +#define CSR_EEPROM_GP_BAD_SIG_EEP_GOOD_SIG_OTP (0x00000001) +#define CSR_EEPROM_GP_GOOD_SIG_EEP_LESS_THAN_4K (0x00000002) +#define CSR_EEPROM_GP_GOOD_SIG_EEP_MORE_THAN_4K (0x00000004) + +/* One-time-programmable memory general purpose reg */ +#define CSR_OTP_GP_REG_DEVICE_SELECT (0x00010000) /* 0 - EEPROM, 1 - OTP */ +#define CSR_OTP_GP_REG_OTP_ACCESS_MODE (0x00020000) /* 0 - absolute, 1 - relative */ +#define CSR_OTP_GP_REG_ECC_CORR_STATUS_MSK (0x00100000) /* bit 20 */ +#define CSR_OTP_GP_REG_ECC_UNCORR_STATUS_MSK (0x00200000) /* bit 21 */ + +/* GP REG */ +#define CSR_GP_REG_POWER_SAVE_STATUS_MSK (0x03000000) /* bit 24/25 */ +#define CSR_GP_REG_NO_POWER_SAVE (0x00000000) +#define CSR_GP_REG_MAC_POWER_SAVE (0x01000000) +#define CSR_GP_REG_PHY_POWER_SAVE (0x02000000) +#define CSR_GP_REG_POWER_SAVE_ERROR (0x03000000) + /* CSR GIO */ #define CSR_GIO_REG_VAL_L0S_ENABLED (0x00000002) -/* UCODE DRV GP */ +/* + * UCODE-DRIVER GP (general purpose) mailbox register 1 + * Host driver and uCode write and/or read this register to communicate with + * each other. + * Bit fields: + * 4: UCODE_DISABLE + * Host sets this to request permanent halt of uCode, same as + * sending CARD_STATE command with "halt" bit set. + * 3: CT_KILL_EXIT + * Host sets this to request exit from CT_KILL state, i.e. host thinks + * device temperature is low enough to continue normal operation. + * 2: CMD_BLOCKED + * Host sets this during RF KILL power-down sequence (HW, SW, CT KILL) + * to release uCode to clear all Tx and command queues, enter + * unassociated mode, and power down. + * NOTE: Some devices also use HBUS_TARG_MBX_C register for this bit. + * 1: SW_BIT_RFKILL + * Host sets this when issuing CARD_STATE command to request + * device sleep. + * 0: MAC_SLEEP + * uCode sets this when preparing a power-saving power-down. + * uCode resets this when power-up is complete and SRAM is sane. + * NOTE: device saves internal SRAM data to host when powering down, + * and must restore this data after powering back up. + * MAC_SLEEP is the best indication that restore is complete. + * Later devices (5xxx/6xxx/1xxx) use non-volatile SRAM, and + * do not need to save/restore it. + */ #define CSR_UCODE_DRV_GP1_BIT_MAC_SLEEP (0x00000001) #define CSR_UCODE_SW_BIT_RFKILL (0x00000002) #define CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED (0x00000004) #define CSR_UCODE_DRV_GP1_REG_BIT_CT_KILL_EXIT (0x00000008) +#define CSR_UCODE_DRV_GP1_BIT_D3_CFG_COMPLETE (0x00000020) + +/* GP Driver */ +#define CSR_GP_DRIVER_REG_BIT_RADIO_SKU_MSK (0x00000003) +#define CSR_GP_DRIVER_REG_BIT_RADIO_SKU_3x3_HYB (0x00000000) +#define CSR_GP_DRIVER_REG_BIT_RADIO_SKU_2x2_HYB (0x00000001) +#define CSR_GP_DRIVER_REG_BIT_RADIO_SKU_2x2_IPA (0x00000002) +#define CSR_GP_DRIVER_REG_BIT_CALIB_VERSION6 (0x00000004) +#define CSR_GP_DRIVER_REG_BIT_6050_1x2 (0x00000008) -/* GI Chicken Bits */ +#define CSR_GP_DRIVER_REG_BIT_RADIO_IQ_INVER (0x00000080) + +/* GIO Chicken Bits (PCI Express bus link power management) */ #define CSR_GIO_CHICKEN_BITS_REG_BIT_L1A_NO_L0S_RX (0x00800000) #define CSR_GIO_CHICKEN_BITS_REG_BIT_DIS_L0S_EXIT_TIMER (0x20000000) /* LED */ #define CSR_LED_BSM_CTRL_MSK (0xFFFFFFDF) -#define CSR_LED_REG_TRUN_ON (0x78) -#define CSR_LED_REG_TRUN_OFF (0x38) +#define CSR_LED_REG_TURN_ON (0x60) +#define CSR_LED_REG_TURN_OFF (0x20) /* ANA_PLL */ -#define CSR39_ANA_PLL_CFG_VAL (0x01000000) #define CSR50_ANA_PLL_CFG_VAL (0x00880300) /* HPET MEM debug */ #define CSR_DBG_HPET_MEM_REG_VAL (0xFFFF0000) -/*=== HBUS (Host-side Bus) ===*/ + +/* DRAM INT TABLE */ +#define CSR_DRAM_INT_TBL_ENABLE (1 << 31) +#define CSR_DRAM_INIT_TBL_WRAP_CHECK (1 << 27) + +/* + * SHR target access (Shared block memory space) + * + * Shared internal registers can be accessed directly from PCI bus through SHR + * arbiter without need for the MAC HW to be powered up. This is possible due to + * indirect read/write via HEEP_CTRL_WRD_PCIEX_CTRL (0xEC) and + * HEEP_CTRL_WRD_PCIEX_DATA (0xF4) registers. + * + * Use iwl_write32()/iwl_read32() family to access these registers. The MAC HW + * need not be powered up so no "grab inc access" is required. + */ + +/* + * Registers for accessing shared registers (e.g. SHR_APMG_GP1, + * SHR_APMG_XTAL_CFG). For example, to read from SHR_APMG_GP1 register (0x1DC), + * first, write to the control register: + * HEEP_CTRL_WRD_PCIEX_CTRL[15:0] = 0x1DC (offset of the SHR_APMG_GP1 register) + * HEEP_CTRL_WRD_PCIEX_CTRL[29:28] = 2 (read access) + * second, read from the data register HEEP_CTRL_WRD_PCIEX_DATA[31:0]. + * + * To write the register, first, write to the data register + * HEEP_CTRL_WRD_PCIEX_DATA[31:0] and then: + * HEEP_CTRL_WRD_PCIEX_CTRL[15:0] = 0x1DC (offset of the SHR_APMG_GP1 register) + * HEEP_CTRL_WRD_PCIEX_CTRL[29:28] = 3 (write access) + */ +#define HEEP_CTRL_WRD_PCIEX_CTRL_REG (CSR_BASE+0x0ec) +#define HEEP_CTRL_WRD_PCIEX_DATA_REG (CSR_BASE+0x0f4) + +/* + * HBUS (Host-side Bus) + * + * HBUS registers are mapped directly into PCI bus space, but are used + * to indirectly access device's internal memory or registers that + * may be powered-down. + * + * Use iwl_write_direct32()/iwl_read_direct32() family for these registers; + * host must "grab nic access" via CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ + * to make sure the MAC (uCode processor, etc.) is powered up for accessing + * internal resources. + * + * Do not use iwl_write32()/iwl_read32() family to access these registers; + * these provide only simple PCI bus access, without waking up the MAC. + */ #define HBUS_BASE (0x400) + /* * Registers for accessing device's internal SRAM memory (e.g. SCD SRAM * structures, error log, event log, verifying uCode load). @@ -264,6 +464,10 @@ #define HBUS_TARG_MEM_WDAT (HBUS_BASE+0x018) #define HBUS_TARG_MEM_RDAT (HBUS_BASE+0x01c) +/* Mailbox C, used as workaround alternative to CSR_UCODE_DRV_GP1 mailbox */ +#define HBUS_TARG_MBX_C (HBUS_BASE+0x030) +#define HBUS_TARG_MBX_C_REG_BIT_CMD_BLOCKED (0x00000004) + /* * Registers for accessing device's internal peripheral registers * (e.g. SCD, BSM, etc.). First write to address register, @@ -277,17 +481,50 @@ #define HBUS_TARG_PRPH_WDAT (HBUS_BASE+0x04c) #define HBUS_TARG_PRPH_RDAT (HBUS_BASE+0x050) +/* Used to enable DBGM */ +#define HBUS_TARG_TEST_REG (HBUS_BASE+0x05c) + /* - * Per-Tx-queue write pointer (index, really!) (3945 and 4965). + * Per-Tx-queue write pointer (index, really!) * Indicates index to next TFD that driver will fill (1 past latest filled). * Bit usage: * 0-7: queue write index * 11-8: queue selector */ #define HBUS_TARG_WRPTR (HBUS_BASE+0x060) -#define HBUS_TARG_MBX_C (HBUS_BASE+0x030) -#define HBUS_TARG_MBX_C_REG_BIT_CMD_BLOCKED (0x00000004) +/********************************************************** + * CSR values + **********************************************************/ + /* + * host interrupt timeout value + * used with setting interrupt coalescing timer + * the CSR_INT_COALESCING is an 8 bit register in 32-usec unit + * + * default interrupt coalescing timer is 64 x 32 = 2048 usecs + */ +#define IWL_HOST_INT_TIMEOUT_MAX (0xFF) +#define IWL_HOST_INT_TIMEOUT_DEF (0x40) +#define IWL_HOST_INT_TIMEOUT_MIN (0x0) +#define IWL_HOST_INT_OPER_MODE BIT(31) + +/***************************************************************************** + * 7000/3000 series SHR DTS addresses * + *****************************************************************************/ +/* Diode Results Register Structure: */ +enum dtd_diode_reg { + DTS_DIODE_REG_DIG_VAL = 0x000000FF, /* bits [7:0] */ + DTS_DIODE_REG_VREF_LOW = 0x0000FF00, /* bits [15:8] */ + DTS_DIODE_REG_VREF_HIGH = 0x00FF0000, /* bits [23:16] */ + DTS_DIODE_REG_VREF_ID = 0x03000000, /* bits [25:24] */ + DTS_DIODE_REG_PASS_ONCE = 0x80000000, /* bits [31:31] */ + DTS_DIODE_REG_FLAGS_MSK = 0xFF000000, /* bits [31:24] */ +/* Those are the masks INSIDE the flags bit-field: */ + DTS_DIODE_REG_FLAGS_VREFS_ID_POS = 0, + DTS_DIODE_REG_FLAGS_VREFS_ID = 0x00000003, /* bits [1:0] */ + DTS_DIODE_REG_FLAGS_PASS_ONCE_POS = 7, + DTS_DIODE_REG_FLAGS_PASS_ONCE = 0x00000080, /* bits [7:7] */ +}; #endif /* !__iwl_csr_h__ */ |