diff options
Diffstat (limited to 'drivers/net/wireless/hostap/hostap_cs.c')
| -rw-r--r-- | drivers/net/wireless/hostap/hostap_cs.c | 140 |
1 files changed, 24 insertions, 116 deletions
diff --git a/drivers/net/wireless/hostap/hostap_cs.c b/drivers/net/wireless/hostap/hostap_cs.c index ba54d1b04d2..b6ec51923b2 100644 --- a/drivers/net/wireless/hostap/hostap_cs.c +++ b/drivers/net/wireless/hostap/hostap_cs.c @@ -1,7 +1,6 @@ #define PRISM2_PCCARD #include <linux/module.h> -#include <linux/init.h> #include <linux/if.h> #include <linux/slab.h> #include <linux/wait.h> @@ -12,7 +11,6 @@ #include <linux/wireless.h> #include <net/iw_handler.h> -#include <pcmcia/cs.h> #include <pcmcia/cistpl.h> #include <pcmcia/cisreg.h> #include <pcmcia/ds.h> @@ -437,7 +435,6 @@ static int hostap_cs_probe(struct pcmcia_device *p_dev) int ret; PDEBUG(DEBUG_HW, "%s: setting Vcc=33 (constant)\n", dev_info); - p_dev->conf.IntType = INT_MEMORY_AND_IO; ret = prism2_config(p_dev); if (ret) { @@ -468,74 +465,11 @@ static void prism2_detach(struct pcmcia_device *link) } -/* run after a CARD_INSERTION event is received to configure the PCMCIA - * socket and make the device available to the system */ - -static int prism2_config_check(struct pcmcia_device *p_dev, - cistpl_cftable_entry_t *cfg, - cistpl_cftable_entry_t *dflt, - unsigned int vcc, - void *priv_data) +static int prism2_config_check(struct pcmcia_device *p_dev, void *priv_data) { - if (cfg->index == 0) - return -ENODEV; - - PDEBUG(DEBUG_EXTRA, "Checking CFTABLE_ENTRY 0x%02X " - "(default 0x%02X)\n", cfg->index, dflt->index); - - /* Does this card need audio output? */ - if (cfg->flags & CISTPL_CFTABLE_AUDIO) { - p_dev->conf.Attributes |= CONF_ENABLE_SPKR; - p_dev->conf.Status = CCSR_AUDIO_ENA; - } - - /* Use power settings for Vcc and Vpp if present */ - /* Note that the CIS values need to be rescaled */ - if (cfg->vcc.present & (1 << CISTPL_POWER_VNOM)) { - if (vcc != cfg->vcc.param[CISTPL_POWER_VNOM] / - 10000 && !ignore_cis_vcc) { - PDEBUG(DEBUG_EXTRA, " Vcc mismatch - skipping" - " this entry\n"); - return -ENODEV; - } - } else if (dflt->vcc.present & (1 << CISTPL_POWER_VNOM)) { - if (vcc != dflt->vcc.param[CISTPL_POWER_VNOM] / - 10000 && !ignore_cis_vcc) { - PDEBUG(DEBUG_EXTRA, " Vcc (default) mismatch " - "- skipping this entry\n"); - return -ENODEV; - } - } + if (p_dev->config_index == 0) + return -EINVAL; - if (cfg->vpp1.present & (1 << CISTPL_POWER_VNOM)) - p_dev->conf.Vpp = cfg->vpp1.param[CISTPL_POWER_VNOM] / 10000; - else if (dflt->vpp1.present & (1 << CISTPL_POWER_VNOM)) - p_dev->conf.Vpp = dflt->vpp1.param[CISTPL_POWER_VNOM] / 10000; - - /* Do we need to allocate an interrupt? */ - p_dev->conf.Attributes |= CONF_ENABLE_IRQ; - - /* IO window settings */ - PDEBUG(DEBUG_EXTRA, "IO window settings: cfg->io.nwin=%d " - "dflt->io.nwin=%d\n", - cfg->io.nwin, dflt->io.nwin); - p_dev->resource[0]->end = p_dev->resource[1]->end = 0; - if ((cfg->io.nwin > 0) || (dflt->io.nwin > 0)) { - cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &dflt->io; - p_dev->resource[0]->flags &= ~IO_DATA_PATH_WIDTH; - p_dev->resource[0]->flags |= - pcmcia_io_cfg_data_width(io->flags); - p_dev->io_lines = io->flags & CISTPL_IO_LINES_MASK; - p_dev->resource[0]->start = io->win[0].base; - p_dev->resource[0]->end = io->win[0].len; - if (io->nwin > 1) { - p_dev->resource[1]->flags = p_dev->resource[0]->flags; - p_dev->resource[1]->start = io->win[1].base; - p_dev->resource[1]->end = io->win[1].len; - } - } - - /* This reserves IO space but doesn't actually enable it */ return pcmcia_request_io(p_dev); } @@ -557,6 +491,10 @@ static int prism2_config(struct pcmcia_device *link) } /* Look for an appropriate configuration table entry in the CIS */ + link->config_flags |= CONF_AUTO_SET_VPP | CONF_AUTO_AUDIO | + CONF_AUTO_CHECK_VCC | CONF_AUTO_SET_IO | CONF_ENABLE_IRQ; + if (ignore_cis_vcc) + link->config_flags &= ~CONF_AUTO_CHECK_VCC; ret = pcmcia_loop_config(link, prism2_config_check, NULL); if (ret) { if (!ignore_cis_vcc) @@ -579,43 +517,23 @@ static int prism2_config(struct pcmcia_device *link) hw_priv->link = link; /* - * Make sure the IRQ handler cannot proceed until at least - * dev->base_addr is initialized. + * We enable IRQ here, but IRQ handler will not proceed + * until dev->base_addr is set below. This protect us from + * receive interrupts when driver is not initialized. */ - spin_lock_irqsave(&local->irq_init_lock, flags); - ret = pcmcia_request_irq(link, prism2_interrupt); if (ret) - goto failed_unlock; + goto failed; - /* - * This actually configures the PCMCIA socket -- setting up - * the I/O windows and the interrupt mapping, and putting the - * card and host interface into "Memory and IO" mode. - */ - ret = pcmcia_request_configuration(link, &link->conf); + ret = pcmcia_enable_device(link); if (ret) - goto failed_unlock; + goto failed; + spin_lock_irqsave(&local->irq_init_lock, flags); dev->irq = link->irq; dev->base_addr = link->resource[0]->start; - spin_unlock_irqrestore(&local->irq_init_lock, flags); - /* Finally, report what we've done */ - printk(KERN_INFO "%s: index 0x%02x: ", - dev_info, link->conf.ConfigIndex); - if (link->conf.Vpp) - printk(", Vpp %d.%d", link->conf.Vpp / 10, - link->conf.Vpp % 10); - if (link->conf.Attributes & CONF_ENABLE_IRQ) - printk(", irq %d", link->irq); - if (link->resource[0]) - printk(" & %pR", link->resource[0]); - if (link->resource[1]) - printk(" & %pR", link->resource[1]); - printk("\n"); - local->shutdown = 0; sandisk_enable_wireless(dev); @@ -626,8 +544,6 @@ static int prism2_config(struct pcmcia_device *link) return ret; - failed_unlock: - spin_unlock_irqrestore(&local->irq_init_lock, flags); failed: kfree(hw_priv); prism2_release((u_long)link); @@ -703,7 +619,7 @@ static int hostap_cs_resume(struct pcmcia_device *link) return 0; } -static struct pcmcia_device_id hostap_cs_ids[] = { +static const struct pcmcia_device_id hostap_cs_ids[] = { PCMCIA_DEVICE_MANF_CARD(0x000b, 0x7100), PCMCIA_DEVICE_MANF_CARD(0x000b, 0x7300), PCMCIA_DEVICE_MANF_CARD(0x0101, 0x0777), @@ -731,12 +647,17 @@ static struct pcmcia_device_id hostap_cs_ids[] = { 0x74c5e40d), PCMCIA_DEVICE_MANF_CARD_PROD_ID1(0x0156, 0x0002, "Intersil", 0x4b801a17), + PCMCIA_DEVICE_MANF_CARD_PROD_ID3(0x0156, 0x0002, "Version 01.02", + 0x4b74baa0), PCMCIA_MFC_DEVICE_PROD_ID12(0, "SanDisk", "ConnectPlus", 0x7a954bd9, 0x74be00c6), PCMCIA_DEVICE_PROD_ID123( "Addtron", "AWP-100 Wireless PCMCIA", "Version 01.02", 0xe6ec52ce, 0x08649af2, 0x4b74baa0), PCMCIA_DEVICE_PROD_ID123( + "Canon", "Wireless LAN CF Card K30225", "Version 01.00", + 0x96ef6fe2, 0x263fcbab, 0xa57adb8c), + PCMCIA_DEVICE_PROD_ID123( "D", "Link DWL-650 11Mbps WLAN Card", "Version 01.02", 0x71b18589, 0xb6f1b0ab, 0x4b74baa0), PCMCIA_DEVICE_PROD_ID123( @@ -756,6 +677,8 @@ static struct pcmcia_device_id hostap_cs_ids[] = { PCMCIA_DEVICE_PROD_ID12( "ZoomAir 11Mbps High", "Rate wireless Networking", 0x273fe3db, 0x32a1eaee), + PCMCIA_DEVICE_PROD_ID12("NETGEAR MA401 Wireless PC", "Card", + 0xa37434e9, 0x9762e8f1), PCMCIA_DEVICE_PROD_ID123( "Pretec", "CompactWLAN Card 802.11b", "2.5", 0x1cadd3e5, 0xe697636c, 0x7a5bfcf1), @@ -779,9 +702,7 @@ MODULE_DEVICE_TABLE(pcmcia, hostap_cs_ids); static struct pcmcia_driver hostap_driver = { - .drv = { - .name = "hostap_cs", - }, + .name = "hostap_cs", .probe = hostap_cs_probe, .remove = prism2_detach, .owner = THIS_MODULE, @@ -789,17 +710,4 @@ static struct pcmcia_driver hostap_driver = { .suspend = hostap_cs_suspend, .resume = hostap_cs_resume, }; - -static int __init init_prism2_pccard(void) -{ - return pcmcia_register_driver(&hostap_driver); -} - -static void __exit exit_prism2_pccard(void) -{ - pcmcia_unregister_driver(&hostap_driver); -} - - -module_init(init_prism2_pccard); -module_exit(exit_prism2_pccard); +module_pcmcia_driver(hostap_driver); |