aboutsummaryrefslogtreecommitdiff
path: root/drivers/net/wireless/Kconfig
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/wireless/Kconfig')
-rw-r--r--drivers/net/wireless/Kconfig314
1 files changed, 54 insertions, 260 deletions
diff --git a/drivers/net/wireless/Kconfig b/drivers/net/wireless/Kconfig
index d7a764a2fc1..b2137e8f7ca 100644
--- a/drivers/net/wireless/Kconfig
+++ b/drivers/net/wireless/Kconfig
@@ -5,6 +5,8 @@
menuconfig WLAN
bool "Wireless LAN"
depends on !S390
+ depends on NET
+ select WIRELESS
default y
---help---
This section contains all the pre 802.11 and 802.11 wireless
@@ -15,114 +17,12 @@ menuconfig WLAN
if WLAN
-menuconfig WLAN_PRE80211
- bool "Wireless LAN (pre-802.11)"
- depends on NETDEVICES
- ---help---
- Say Y if you have any pre-802.11 wireless LAN hardware.
-
- This option does not affect the kernel build, it only
- lets you choose drivers.
-
-config STRIP
- tristate "STRIP (Metricom starmode radio IP)"
- depends on INET && WLAN_PRE80211
- select WIRELESS_EXT
- ---help---
- Say Y if you have a Metricom radio and intend to use Starmode Radio
- IP. STRIP is a radio protocol developed for the MosquitoNet project
- to send Internet traffic using Metricom radios. Metricom radios are
- small, battery powered, 100kbit/sec packet radio transceivers, about
- the size and weight of a cellular telephone. (You may also have heard
- them called "Metricom modems" but we avoid the term "modem" because
- it misleads many people into thinking that you can plug a Metricom
- modem into a phone line and use it as a modem.)
-
- You can use STRIP on any Linux machine with a serial port, although
- it is obviously most useful for people with laptop computers. If you
- think you might get a Metricom radio in the future, there is no harm
- in saying Y to STRIP now, except that it makes the kernel a bit
- bigger.
-
- To compile this as a module, choose M here: the module will be
- called strip.
-
-config ARLAN
- tristate "Aironet Arlan 655 & IC2200 DS support"
- depends on ISA && !64BIT && WLAN_PRE80211
- select WIRELESS_EXT
- ---help---
- Aironet makes Arlan, a class of wireless LAN adapters. These use the
- www.Telxon.com chip, which is also used on several similar cards.
- This driver is tested on the 655 and IC2200 series cards. Look at
- <http://www.ylenurme.ee/~elmer/655/> for the latest information.
-
- The driver is built as two modules, arlan and arlan-proc. The latter
- is the /proc interface and is not needed most of time.
-
- On some computers the card ends up in non-valid state after some
- time. Use a ping-reset script to clear it.
-
-config WAVELAN
- tristate "AT&T/Lucent old WaveLAN & DEC RoamAbout DS ISA support"
- depends on ISA && WLAN_PRE80211
- select WIRELESS_EXT
- ---help---
- The Lucent WaveLAN (formerly NCR and AT&T; or DEC RoamAbout DS) is
- a Radio LAN (wireless Ethernet-like Local Area Network) using the
- radio frequencies 900 MHz and 2.4 GHz.
-
- If you want to use an ISA WaveLAN card under Linux, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>. Some more specific
- information is contained in
- <file:Documentation/networking/wavelan.txt> and in the source code
- <file:drivers/net/wireless/wavelan.p.h>.
-
- You will also need the wireless tools package available from
- <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.
- Please read the man pages contained therein.
-
- To compile this driver as a module, choose M here: the module will be
- called wavelan.
-
-config PCMCIA_WAVELAN
- tristate "AT&T/Lucent old WaveLAN Pcmcia wireless support"
- depends on PCMCIA && WLAN_PRE80211
- select WIRELESS_EXT
- help
- Say Y here if you intend to attach an AT&T/Lucent Wavelan PCMCIA
- (PC-card) wireless Ethernet networking card to your computer. This
- driver is for the non-IEEE-802.11 Wavelan cards.
-
- To compile this driver as a module, choose M here: the module will be
- called wavelan_cs. If unsure, say N.
-
-config PCMCIA_NETWAVE
- tristate "Xircom Netwave AirSurfer Pcmcia wireless support"
- depends on PCMCIA && WLAN_PRE80211
- select WIRELESS_EXT
- help
- Say Y here if you intend to attach this type of PCMCIA (PC-card)
- wireless Ethernet networking card to your computer.
-
- To compile this driver as a module, choose M here: the module will be
- called netwave_cs. If unsure, say N.
-
-
-menuconfig WLAN_80211
- bool "Wireless LAN (IEEE 802.11)"
- depends on NETDEVICES
- ---help---
- Say Y if you have any 802.11 wireless LAN hardware.
-
- This option does not affect the kernel build, it only
- lets you choose drivers.
-
config PCMCIA_RAYCS
tristate "Aviator/Raytheon 2.4GHz wireless support"
- depends on PCMCIA && WLAN_80211
+ depends on PCMCIA
select WIRELESS_EXT
+ select WEXT_SPY
+ select WEXT_PRIV
---help---
Say Y here if you intend to attach an Aviator/Raytheon PCMCIA
(PC-card) wireless Ethernet networking card to your computer.
@@ -132,53 +32,19 @@ config PCMCIA_RAYCS
To compile this driver as a module, choose M here: the module will be
called ray_cs. If unsure, say N.
-config LIBERTAS
- tristate "Marvell 8xxx Libertas WLAN driver support"
- depends on WLAN_80211
- select WIRELESS_EXT
- select LIB80211
- select FW_LOADER
- ---help---
- A library for Marvell Libertas 8xxx devices.
-
-config LIBERTAS_USB
- tristate "Marvell Libertas 8388 USB 802.11b/g cards"
- depends on LIBERTAS && USB
- ---help---
- A driver for Marvell Libertas 8388 USB devices.
-
-config LIBERTAS_CS
- tristate "Marvell Libertas 8385 CompactFlash 802.11b/g cards"
- depends on LIBERTAS && PCMCIA
- select FW_LOADER
- ---help---
- A driver for Marvell Libertas 8385 CompactFlash devices.
-
-config LIBERTAS_SDIO
- tristate "Marvell Libertas 8385/8686/8688 SDIO 802.11b/g cards"
- depends on LIBERTAS && MMC
- ---help---
- A driver for Marvell Libertas 8385/8686/8688 SDIO devices.
-
-config LIBERTAS_SPI
- tristate "Marvell Libertas 8686 SPI 802.11b/g cards"
- depends on LIBERTAS && SPI
- ---help---
- A driver for Marvell Libertas 8686 SPI devices.
-
-config LIBERTAS_DEBUG
- bool "Enable full debugging output in the Libertas module."
- depends on LIBERTAS
- ---help---
- Debugging support.
-
config LIBERTAS_THINFIRM
tristate "Marvell 8xxx Libertas WLAN driver support with thin firmware"
- depends on WLAN_80211 && MAC80211
+ depends on MAC80211
select FW_LOADER
---help---
A library for Marvell Libertas 8xxx devices using thinfirm.
+config LIBERTAS_THINFIRM_DEBUG
+ bool "Enable full debugging output in the Libertas thin firmware module."
+ depends on LIBERTAS_THINFIRM
+ ---help---
+ Debugging support.
+
config LIBERTAS_THINFIRM_USB
tristate "Marvell Libertas 8388 USB 802.11b/g cards with thin firmware"
depends on LIBERTAS_THINFIRM && USB
@@ -187,9 +53,11 @@ config LIBERTAS_THINFIRM_USB
config AIRO
tristate "Cisco/Aironet 34X/35X/4500/4800 ISA and PCI cards"
- depends on ISA_DMA_API && WLAN_80211 && (PCI || BROKEN)
+ depends on CFG80211 && ISA_DMA_API && (PCI || BROKEN)
select WIRELESS_EXT
select CRYPTO
+ select WEXT_SPY
+ select WEXT_PRIV
---help---
This is the standard Linux driver to support Cisco/Aironet ISA and
PCI 802.11 wireless cards.
@@ -205,8 +73,9 @@ config AIRO
config ATMEL
tristate "Atmel at76c50x chipset 802.11b support"
- depends on (PCI || PCMCIA) && WLAN_80211
+ depends on CFG80211 && (PCI || PCMCIA)
select WIRELESS_EXT
+ select WEXT_PRIV
select FW_LOADER
select CRC32
---help---
@@ -239,7 +108,7 @@ config PCMCIA_ATMEL
config AT76C50X_USB
tristate "Atmel at76c503/at76c505/at76c505a USB cards"
- depends on MAC80211 && WLAN_80211 && USB
+ depends on MAC80211 && USB
select FW_LOADER
---help---
Enable support for USB Wireless devices using Atmel at76c503,
@@ -247,8 +116,10 @@ config AT76C50X_USB
config AIRO_CS
tristate "Cisco/Aironet 34X/35X/4500/4800 PCMCIA cards"
- depends on PCMCIA && (BROKEN || !M32R) && WLAN_80211
+ depends on CFG80211 && PCMCIA && (BROKEN || !M32R)
select WIRELESS_EXT
+ select WEXT_SPY
+ select WEXT_PRIV
select CRYPTO
select CRYPTO_AES
---help---
@@ -266,27 +137,26 @@ config AIRO_CS
Cisco Linux utilities can be used to configure the card.
config PCMCIA_WL3501
- tristate "Planet WL3501 PCMCIA cards"
- depends on EXPERIMENTAL && PCMCIA && WLAN_80211
- select WIRELESS_EXT
- ---help---
- A driver for WL3501 PCMCIA 802.11 wireless cards made by Planet.
- It has basic support for Linux wireless extensions and initial
- micro support for ethtool.
+ tristate "Planet WL3501 PCMCIA cards"
+ depends on CFG80211 && PCMCIA
+ select WIRELESS_EXT
+ select WEXT_SPY
+ help
+ A driver for WL3501 PCMCIA 802.11 wireless cards made by Planet.
+ It has basic support for Linux wireless extensions and initial
+ micro support for ethtool.
config PRISM54
tristate 'Intersil Prism GT/Duette/Indigo PCI/Cardbus (DEPRECATED)'
- depends on PCI && EXPERIMENTAL && WLAN_80211
+ depends on PCI
select WIRELESS_EXT
+ select WEXT_SPY
+ select WEXT_PRIV
select FW_LOADER
---help---
This enables support for FullMAC PCI/Cardbus prism54 devices. This
driver is now deprecated in favor for the SoftMAC driver, p54pci.
- p54pci supports FullMAC PCI/Cardbus devices as well. For details on
- the scheduled removal of this driver on the kernel see the feature
- removal schedule:
-
- Documentation/feature-removal-schedule.txt
+ p54pci supports FullMAC PCI/Cardbus devices as well.
For more information refer to the p54 wiki:
@@ -298,8 +168,9 @@ config PRISM54
config USB_ZD1201
tristate "USB ZD1201 based Wireless device support"
- depends on USB && WLAN_80211
+ depends on CFG80211 && USB
select WIRELESS_EXT
+ select WEXT_PRIV
select FW_LOADER
---help---
Say Y if you want to use wireless LAN adapters based on the ZyDAS
@@ -316,7 +187,7 @@ config USB_ZD1201
config USB_NET_RNDIS_WLAN
tristate "Wireless RNDIS USB support"
- depends on USB && WLAN_80211 && EXPERIMENTAL
+ depends on USB
depends on CFG80211
select USB_USBNET
select USB_NET_CDCETHER
@@ -342,94 +213,11 @@ config USB_NET_RNDIS_WLAN
If you choose to build a module, it'll be called rndis_wlan.
-config RTL8180
- tristate "Realtek 8180/8185 PCI support"
- depends on MAC80211 && PCI && WLAN_80211 && EXPERIMENTAL
- select EEPROM_93CX6
- ---help---
- This is a driver for RTL8180 and RTL8185 based cards.
- These are PCI based chips found in cards such as:
-
- (RTL8185 802.11g)
- A-Link WL54PC
-
- (RTL8180 802.11b)
- Belkin F5D6020 v3
- Belkin F5D6020 v3
- Dlink DWL-610
- Dlink DWL-510
- Netgear MA521
- Level-One WPC-0101
- Acer Aspire 1357 LMi
- VCTnet PC-11B1
- Ovislink AirLive WL-1120PCM
- Mentor WL-PCI
- Linksys WPC11 v4
- TrendNET TEW-288PI
- D-Link DWL-520 Rev D
- Repotec RP-WP7126
- TP-Link TL-WN250/251
- Zonet ZEW1000
- Longshine LCS-8031-R
- HomeLine HLW-PCC200
- GigaFast WF721-AEX
- Planet WL-3553
- Encore ENLWI-PCI1-NT
- TrendNET TEW-266PC
- Gigabyte GN-WLMR101
- Siemens-fujitsu Amilo D1840W
- Edimax EW-7126
- PheeNet WL-11PCIR
- Tonze PC-2100T
- Planet WL-8303
- Dlink DWL-650 v M1
- Edimax EW-7106
- Q-Tec 770WC
- Topcom Skyr@cer 4011b
- Roper FreeLan 802.11b (edition 2004)
- Wistron Neweb Corp CB-200B
- Pentagram HorNET
- QTec 775WC
- TwinMOS Booming B Series
- Micronet SP906BB
- Sweex LC700010
- Surecom EP-9428
- Safecom SWLCR-1100
-
- Thanks to Realtek for their support!
-
-config RTL8187
- tristate "Realtek 8187 and 8187B USB support"
- depends on MAC80211 && USB && WLAN_80211
- select EEPROM_93CX6
- ---help---
- This is a driver for RTL8187 and RTL8187B based cards.
- These are USB based chips found in devices such as:
-
- Netgear WG111v2
- Level 1 WNC-0301USB
- Micronet SP907GK V5
- Encore ENUWI-G2
- Trendnet TEW-424UB
- ASUS P5B Deluxe/P5K Premium motherboards
- Toshiba Satellite Pro series of laptops
- Asus Wireless Link
- Linksys WUSB54GC-EU v2
- (v1 = rt73usb; v3 is rt2070-based,
- use staging/rt3070 or try rt2800usb)
-
- Thanks to Realtek for their support!
-
-# If possible, automatically enable LEDs for RTL8187.
-
-config RTL8187_LEDS
- bool
- depends on RTL8187 && MAC80211_LEDS && (LEDS_CLASS = y || LEDS_CLASS = RTL8187)
- default y
+source "drivers/net/wireless/rtl818x/Kconfig"
config ADM8211
tristate "ADMtek ADM8211 support"
- depends on MAC80211 && PCI && WLAN_80211 && EXPERIMENTAL
+ depends on MAC80211 && PCI
select CRC32
select EEPROM_93CX6
---help---
@@ -456,7 +244,7 @@ config ADM8211
config MAC80211_HWSIM
tristate "Simulated radio testing tool for mac80211"
- depends on MAC80211 && WLAN_80211
+ depends on MAC80211
---help---
This driver is a developer testing tool that can be used to test
IEEE 802.11 networking stack (mac80211) functionality. This is not
@@ -469,24 +257,30 @@ config MAC80211_HWSIM
config MWL8K
tristate "Marvell 88W8xxx PCI/PCIe Wireless support"
- depends on MAC80211 && PCI && WLAN_80211 && EXPERIMENTAL
+ depends on MAC80211 && PCI
---help---
This driver supports Marvell TOPDOG 802.11 wireless cards.
To compile this driver as a module, choose M here: the module
will be called mwl8k. If unsure, say N.
-source "drivers/net/wireless/p54/Kconfig"
source "drivers/net/wireless/ath/Kconfig"
-source "drivers/net/wireless/ipw2x00/Kconfig"
-source "drivers/net/wireless/iwlwifi/Kconfig"
-source "drivers/net/wireless/hostap/Kconfig"
source "drivers/net/wireless/b43/Kconfig"
source "drivers/net/wireless/b43legacy/Kconfig"
-source "drivers/net/wireless/zd1211rw/Kconfig"
-source "drivers/net/wireless/rt2x00/Kconfig"
+source "drivers/net/wireless/brcm80211/Kconfig"
+source "drivers/net/wireless/hostap/Kconfig"
+source "drivers/net/wireless/ipw2x00/Kconfig"
+source "drivers/net/wireless/iwlwifi/Kconfig"
+source "drivers/net/wireless/iwlegacy/Kconfig"
+source "drivers/net/wireless/libertas/Kconfig"
source "drivers/net/wireless/orinoco/Kconfig"
-source "drivers/net/wireless/wl12xx/Kconfig"
-source "drivers/net/wireless/iwmc3200wifi/Kconfig"
+source "drivers/net/wireless/p54/Kconfig"
+source "drivers/net/wireless/rt2x00/Kconfig"
+source "drivers/net/wireless/rtlwifi/Kconfig"
+source "drivers/net/wireless/ti/Kconfig"
+source "drivers/net/wireless/zd1211rw/Kconfig"
+source "drivers/net/wireless/mwifiex/Kconfig"
+source "drivers/net/wireless/cw1200/Kconfig"
+source "drivers/net/wireless/rsi/Kconfig"
endif # WLAN
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2026-01-09 05:29:47 +0000