diff options
Diffstat (limited to 'drivers/net/sfc/sfe4001.c')
| -rw-r--r-- | drivers/net/sfc/sfe4001.c | 266 |
1 files changed, 0 insertions, 266 deletions
diff --git a/drivers/net/sfc/sfe4001.c b/drivers/net/sfc/sfe4001.c deleted file mode 100644 index 66a0d1442ab..00000000000 --- a/drivers/net/sfc/sfe4001.c +++ /dev/null @@ -1,266 +0,0 @@ -/**************************************************************************** - * Driver for Solarflare Solarstorm network controllers and boards - * Copyright 2007 Solarflare Communications Inc. - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License version 2 as published - * by the Free Software Foundation, incorporated herein by reference. - */ - -/***************************************************************************** - * Support for the SFE4001 NIC: driver code for the PCA9539 I/O expander that - * controls the PHY power rails, and for the MAX6647 temp. sensor used to check - * the PHY - */ -#include <linux/delay.h> -#include "efx.h" -#include "phy.h" -#include "boards.h" -#include "falcon.h" -#include "falcon_hwdefs.h" -#include "mac.h" - -/************************************************************************** - * - * I2C IO Expander device - * - **************************************************************************/ -#define PCA9539 0x74 - -#define P0_IN 0x00 -#define P0_OUT 0x02 -#define P0_INVERT 0x04 -#define P0_CONFIG 0x06 - -#define P0_EN_1V0X_LBN 0 -#define P0_EN_1V0X_WIDTH 1 -#define P0_EN_1V2_LBN 1 -#define P0_EN_1V2_WIDTH 1 -#define P0_EN_2V5_LBN 2 -#define P0_EN_2V5_WIDTH 1 -#define P0_EN_3V3X_LBN 3 -#define P0_EN_3V3X_WIDTH 1 -#define P0_EN_5V_LBN 4 -#define P0_EN_5V_WIDTH 1 -#define P0_SHORTEN_JTAG_LBN 5 -#define P0_SHORTEN_JTAG_WIDTH 1 -#define P0_X_TRST_LBN 6 -#define P0_X_TRST_WIDTH 1 -#define P0_DSP_RESET_LBN 7 -#define P0_DSP_RESET_WIDTH 1 - -#define P1_IN 0x01 -#define P1_OUT 0x03 -#define P1_INVERT 0x05 -#define P1_CONFIG 0x07 - -#define P1_AFE_PWD_LBN 0 -#define P1_AFE_PWD_WIDTH 1 -#define P1_DSP_PWD25_LBN 1 -#define P1_DSP_PWD25_WIDTH 1 -#define P1_RESERVED_LBN 2 -#define P1_RESERVED_WIDTH 2 -#define P1_SPARE_LBN 4 -#define P1_SPARE_WIDTH 4 - - -/************************************************************************** - * - * Temperature Sensor - * - **************************************************************************/ -#define MAX6647 0x4e - -#define RLTS 0x00 -#define RLTE 0x01 -#define RSL 0x02 -#define RCL 0x03 -#define RCRA 0x04 -#define RLHN 0x05 -#define RLLI 0x06 -#define RRHI 0x07 -#define RRLS 0x08 -#define WCRW 0x0a -#define WLHO 0x0b -#define WRHA 0x0c -#define WRLN 0x0e -#define OSHT 0x0f -#define REET 0x10 -#define RIET 0x11 -#define RWOE 0x19 -#define RWOI 0x20 -#define HYS 0x21 -#define QUEUE 0x22 -#define MFID 0xfe -#define REVID 0xff - -/* Status bits */ -#define MAX6647_BUSY (1 << 7) /* ADC is converting */ -#define MAX6647_LHIGH (1 << 6) /* Local high temp. alarm */ -#define MAX6647_LLOW (1 << 5) /* Local low temp. alarm */ -#define MAX6647_RHIGH (1 << 4) /* Remote high temp. alarm */ -#define MAX6647_RLOW (1 << 3) /* Remote low temp. alarm */ -#define MAX6647_FAULT (1 << 2) /* DXN/DXP short/open circuit */ -#define MAX6647_EOT (1 << 1) /* Remote junction overtemp. */ -#define MAX6647_IOT (1 << 0) /* Local junction overtemp. */ - -static const u8 xgphy_max_temperature = 90; - -void sfe4001_poweroff(struct efx_nic *efx) -{ - struct efx_i2c_interface *i2c = &efx->i2c; - - u8 cfg, out, in; - - EFX_INFO(efx, "%s\n", __func__); - - /* Turn off all power rails */ - out = 0xff; - efx_i2c_write(i2c, PCA9539, P0_OUT, &out, 1); - - /* Disable port 1 outputs on IO expander */ - cfg = 0xff; - efx_i2c_write(i2c, PCA9539, P1_CONFIG, &cfg, 1); - - /* Disable port 0 outputs on IO expander */ - cfg = 0xff; - efx_i2c_write(i2c, PCA9539, P0_CONFIG, &cfg, 1); - - /* Clear any over-temperature alert */ - efx_i2c_read(i2c, MAX6647, RSL, &in, 1); -} - -/* The P0_EN_3V3X line on SFE4001 boards (from A2 onward) is connected - * to the FLASH_CFG_1 input on the DSP. We must keep it high at power- - * up to allow writing the flash (done through MDIO from userland). - */ -unsigned int sfe4001_phy_flash_cfg; -module_param_named(phy_flash_cfg, sfe4001_phy_flash_cfg, uint, 0444); -MODULE_PARM_DESC(phy_flash_cfg, - "Force PHY to enter flash configuration mode"); - -/* This board uses an I2C expander to provider power to the PHY, which needs to - * be turned on before the PHY can be used. - * Context: Process context, rtnl lock held - */ -int sfe4001_poweron(struct efx_nic *efx) -{ - struct efx_i2c_interface *i2c = &efx->i2c; - unsigned int count; - int rc; - u8 out, in, cfg; - efx_dword_t reg; - - /* 10Xpress has fixed-function LED pins, so there is no board-specific - * blink code. */ - efx->board_info.blink = tenxpress_phy_blink; - - /* Ensure that XGXS and XAUI SerDes are held in reset */ - EFX_POPULATE_DWORD_7(reg, XX_PWRDNA_EN, 1, - XX_PWRDNB_EN, 1, - XX_RSTPLLAB_EN, 1, - XX_RESETA_EN, 1, - XX_RESETB_EN, 1, - XX_RSTXGXSRX_EN, 1, - XX_RSTXGXSTX_EN, 1); - falcon_xmac_writel(efx, ®, XX_PWR_RST_REG_MAC); - udelay(10); - - /* Set DSP over-temperature alert threshold */ - EFX_INFO(efx, "DSP cut-out at %dC\n", xgphy_max_temperature); - rc = efx_i2c_write(i2c, MAX6647, WLHO, - &xgphy_max_temperature, 1); - if (rc) - goto fail1; - - /* Read it back and verify */ - rc = efx_i2c_read(i2c, MAX6647, RLHN, &in, 1); - if (rc) - goto fail1; - if (in != xgphy_max_temperature) { - rc = -EFAULT; - goto fail1; - } - - /* Clear any previous over-temperature alert */ - rc = efx_i2c_read(i2c, MAX6647, RSL, &in, 1); - if (rc) - goto fail1; - - /* Enable port 0 and port 1 outputs on IO expander */ - cfg = 0x00; - rc = efx_i2c_write(i2c, PCA9539, P0_CONFIG, &cfg, 1); - if (rc) - goto fail1; - cfg = 0xff & ~(1 << P1_SPARE_LBN); - rc = efx_i2c_write(i2c, PCA9539, P1_CONFIG, &cfg, 1); - if (rc) - goto fail2; - - /* Turn all power off then wait 1 sec. This ensures PHY is reset */ - out = 0xff & ~((0 << P0_EN_1V2_LBN) | (0 << P0_EN_2V5_LBN) | - (0 << P0_EN_3V3X_LBN) | (0 << P0_EN_5V_LBN) | - (0 << P0_EN_1V0X_LBN)); - rc = efx_i2c_write(i2c, PCA9539, P0_OUT, &out, 1); - if (rc) - goto fail3; - - schedule_timeout_uninterruptible(HZ); - count = 0; - do { - /* Turn on 1.2V, 2.5V, 3.3V and 5V power rails */ - out = 0xff & ~((1 << P0_EN_1V2_LBN) | (1 << P0_EN_2V5_LBN) | - (1 << P0_EN_3V3X_LBN) | (1 << P0_EN_5V_LBN) | - (1 << P0_X_TRST_LBN)); - if (sfe4001_phy_flash_cfg) - out |= 1 << P0_EN_3V3X_LBN; - - rc = efx_i2c_write(i2c, PCA9539, P0_OUT, &out, 1); - if (rc) - goto fail3; - msleep(10); - - /* Turn on 1V power rail */ - out &= ~(1 << P0_EN_1V0X_LBN); - rc = efx_i2c_write(i2c, PCA9539, P0_OUT, &out, 1); - if (rc) - goto fail3; - - EFX_INFO(efx, "waiting for power (attempt %d)...\n", count); - - schedule_timeout_uninterruptible(HZ); - - /* Check DSP is powered */ - rc = efx_i2c_read(i2c, PCA9539, P1_IN, &in, 1); - if (rc) - goto fail3; - if (in & (1 << P1_AFE_PWD_LBN)) - goto done; - - /* DSP doesn't look powered in flash config mode */ - if (sfe4001_phy_flash_cfg) - goto done; - } while (++count < 20); - - EFX_INFO(efx, "timed out waiting for power\n"); - rc = -ETIMEDOUT; - goto fail3; - -done: - EFX_INFO(efx, "PHY is powered on\n"); - return 0; - -fail3: - /* Turn off all power rails */ - out = 0xff; - efx_i2c_write(i2c, PCA9539, P0_OUT, &out, 1); - /* Disable port 1 outputs on IO expander */ - out = 0xff; - efx_i2c_write(i2c, PCA9539, P1_CONFIG, &out, 1); -fail2: - /* Disable port 0 outputs on IO expander */ - out = 0xff; - efx_i2c_write(i2c, PCA9539, P0_CONFIG, &out, 1); -fail1: - return rc; -} |