diff options
Diffstat (limited to 'drivers/net/ixgbe/ixgbe_common.c')
| -rw-r--r-- | drivers/net/ixgbe/ixgbe_common.c | 2081 |
1 files changed, 0 insertions, 2081 deletions
diff --git a/drivers/net/ixgbe/ixgbe_common.c b/drivers/net/ixgbe/ixgbe_common.c deleted file mode 100644 index 186a65069b3..00000000000 --- a/drivers/net/ixgbe/ixgbe_common.c +++ /dev/null @@ -1,2081 +0,0 @@ -/******************************************************************************* - - Intel 10 Gigabit PCI Express Linux driver - Copyright(c) 1999 - 2009 Intel Corporation. - - This program is free software; you can redistribute it and/or modify it - under the terms and conditions of the GNU General Public License, - version 2, as published by the Free Software Foundation. - - This program is distributed in the hope it will be useful, but WITHOUT - ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or - FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for - more details. - - You should have received a copy of the GNU General Public License along with - this program; if not, write to the Free Software Foundation, Inc., - 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. - - The full GNU General Public License is included in this distribution in - the file called "COPYING". - - Contact Information: - e1000-devel Mailing List <e1000-devel@lists.sourceforge.net> - Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 - -*******************************************************************************/ - -#include <linux/pci.h> -#include <linux/delay.h> -#include <linux/sched.h> - -#include "ixgbe.h" -#include "ixgbe_common.h" -#include "ixgbe_phy.h" - -static s32 ixgbe_poll_eeprom_eerd_done(struct ixgbe_hw *hw); -static s32 ixgbe_acquire_eeprom(struct ixgbe_hw *hw); -static s32 ixgbe_get_eeprom_semaphore(struct ixgbe_hw *hw); -static void ixgbe_release_eeprom_semaphore(struct ixgbe_hw *hw); -static s32 ixgbe_ready_eeprom(struct ixgbe_hw *hw); -static void ixgbe_standby_eeprom(struct ixgbe_hw *hw); -static void ixgbe_shift_out_eeprom_bits(struct ixgbe_hw *hw, u16 data, - u16 count); -static u16 ixgbe_shift_in_eeprom_bits(struct ixgbe_hw *hw, u16 count); -static void ixgbe_raise_eeprom_clk(struct ixgbe_hw *hw, u32 *eec); -static void ixgbe_lower_eeprom_clk(struct ixgbe_hw *hw, u32 *eec); -static void ixgbe_release_eeprom(struct ixgbe_hw *hw); -static u16 ixgbe_calc_eeprom_checksum(struct ixgbe_hw *hw); - -static void ixgbe_enable_rar(struct ixgbe_hw *hw, u32 index); -static void ixgbe_disable_rar(struct ixgbe_hw *hw, u32 index); -static s32 ixgbe_mta_vector(struct ixgbe_hw *hw, u8 *mc_addr); -static void ixgbe_add_uc_addr(struct ixgbe_hw *hw, u8 *addr, u32 vmdq); - -/** - * ixgbe_start_hw_generic - Prepare hardware for Tx/Rx - * @hw: pointer to hardware structure - * - * Starts the hardware by filling the bus info structure and media type, clears - * all on chip counters, initializes receive address registers, multicast - * table, VLAN filter table, calls routine to set up link and flow control - * settings, and leaves transmit and receive units disabled and uninitialized - **/ -s32 ixgbe_start_hw_generic(struct ixgbe_hw *hw) -{ - u32 ctrl_ext; - - /* Set the media type */ - hw->phy.media_type = hw->mac.ops.get_media_type(hw); - - /* Identify the PHY */ - hw->phy.ops.identify(hw); - - /* - * Store MAC address from RAR0, clear receive address registers, and - * clear the multicast table - */ - hw->mac.ops.init_rx_addrs(hw); - - /* Clear the VLAN filter table */ - hw->mac.ops.clear_vfta(hw); - - /* Clear statistics registers */ - hw->mac.ops.clear_hw_cntrs(hw); - - /* Set No Snoop Disable */ - ctrl_ext = IXGBE_READ_REG(hw, IXGBE_CTRL_EXT); - ctrl_ext |= IXGBE_CTRL_EXT_NS_DIS; - IXGBE_WRITE_REG(hw, IXGBE_CTRL_EXT, ctrl_ext); - IXGBE_WRITE_FLUSH(hw); - - /* Clear adapter stopped flag */ - hw->adapter_stopped = false; - - return 0; -} - -/** - * ixgbe_init_hw_generic - Generic hardware initialization - * @hw: pointer to hardware structure - * - * Initialize the hardware by resetting the hardware, filling the bus info - * structure and media type, clears all on chip counters, initializes receive - * address registers, multicast table, VLAN filter table, calls routine to set - * up link and flow control settings, and leaves transmit and receive units - * disabled and uninitialized - **/ -s32 ixgbe_init_hw_generic(struct ixgbe_hw *hw) -{ - /* Reset the hardware */ - hw->mac.ops.reset_hw(hw); - - /* Start the HW */ - hw->mac.ops.start_hw(hw); - - return 0; -} - -/** - * ixgbe_clear_hw_cntrs_generic - Generic clear hardware counters - * @hw: pointer to hardware structure - * - * Clears all hardware statistics counters by reading them from the hardware - * Statistics counters are clear on read. - **/ -s32 ixgbe_clear_hw_cntrs_generic(struct ixgbe_hw *hw) -{ - u16 i = 0; - - IXGBE_READ_REG(hw, IXGBE_CRCERRS); - IXGBE_READ_REG(hw, IXGBE_ILLERRC); - IXGBE_READ_REG(hw, IXGBE_ERRBC); - IXGBE_READ_REG(hw, IXGBE_MSPDC); - for (i = 0; i < 8; i++) - IXGBE_READ_REG(hw, IXGBE_MPC(i)); - - IXGBE_READ_REG(hw, IXGBE_MLFC); - IXGBE_READ_REG(hw, IXGBE_MRFC); - IXGBE_READ_REG(hw, IXGBE_RLEC); - IXGBE_READ_REG(hw, IXGBE_LXONTXC); - IXGBE_READ_REG(hw, IXGBE_LXONRXC); - IXGBE_READ_REG(hw, IXGBE_LXOFFTXC); - IXGBE_READ_REG(hw, IXGBE_LXOFFRXC); - - for (i = 0; i < 8; i++) { - IXGBE_READ_REG(hw, IXGBE_PXONTXC(i)); - IXGBE_READ_REG(hw, IXGBE_PXONRXC(i)); - IXGBE_READ_REG(hw, IXGBE_PXOFFTXC(i)); - IXGBE_READ_REG(hw, IXGBE_PXOFFRXC(i)); - } - - IXGBE_READ_REG(hw, IXGBE_PRC64); - IXGBE_READ_REG(hw, IXGBE_PRC127); - IXGBE_READ_REG(hw, IXGBE_PRC255); - IXGBE_READ_REG(hw, IXGBE_PRC511); - IXGBE_READ_REG(hw, IXGBE_PRC1023); - IXGBE_READ_REG(hw, IXGBE_PRC1522); - IXGBE_READ_REG(hw, IXGBE_GPRC); - IXGBE_READ_REG(hw, IXGBE_BPRC); - IXGBE_READ_REG(hw, IXGBE_MPRC); - IXGBE_READ_REG(hw, IXGBE_GPTC); - IXGBE_READ_REG(hw, IXGBE_GORCL); - IXGBE_READ_REG(hw, IXGBE_GORCH); - IXGBE_READ_REG(hw, IXGBE_GOTCL); - IXGBE_READ_REG(hw, IXGBE_GOTCH); - for (i = 0; i < 8; i++) - IXGBE_READ_REG(hw, IXGBE_RNBC(i)); - IXGBE_READ_REG(hw, IXGBE_RUC); - IXGBE_READ_REG(hw, IXGBE_RFC); - IXGBE_READ_REG(hw, IXGBE_ROC); - IXGBE_READ_REG(hw, IXGBE_RJC); - IXGBE_READ_REG(hw, IXGBE_MNGPRC); - IXGBE_READ_REG(hw, IXGBE_MNGPDC); - IXGBE_READ_REG(hw, IXGBE_MNGPTC); - IXGBE_READ_REG(hw, IXGBE_TORL); - IXGBE_READ_REG(hw, IXGBE_TORH); - IXGBE_READ_REG(hw, IXGBE_TPR); - IXGBE_READ_REG(hw, IXGBE_TPT); - IXGBE_READ_REG(hw, IXGBE_PTC64); - IXGBE_READ_REG(hw, IXGBE_PTC127); - IXGBE_READ_REG(hw, IXGBE_PTC255); - IXGBE_READ_REG(hw, IXGBE_PTC511); - IXGBE_READ_REG(hw, IXGBE_PTC1023); - IXGBE_READ_REG(hw, IXGBE_PTC1522); - IXGBE_READ_REG(hw, IXGBE_MPTC); - IXGBE_READ_REG(hw, IXGBE_BPTC); - for (i = 0; i < 16; i++) { - IXGBE_READ_REG(hw, IXGBE_QPRC(i)); - IXGBE_READ_REG(hw, IXGBE_QBRC(i)); - IXGBE_READ_REG(hw, IXGBE_QPTC(i)); - IXGBE_READ_REG(hw, IXGBE_QBTC(i)); - } - - return 0; -} - -/** - * ixgbe_read_pba_num_generic - Reads part number from EEPROM - * @hw: pointer to hardware structure - * @pba_num: stores the part number from the EEPROM - * - * Reads the part number from the EEPROM. - **/ -s32 ixgbe_read_pba_num_generic(struct ixgbe_hw *hw, u32 *pba_num) -{ - s32 ret_val; - u16 data; - - ret_val = hw->eeprom.ops.read(hw, IXGBE_PBANUM0_PTR, &data); - if (ret_val) { - hw_dbg(hw, "NVM Read Error\n"); - return ret_val; - } - *pba_num = (u32)(data << 16); - - ret_val = hw->eeprom.ops.read(hw, IXGBE_PBANUM1_PTR, &data); - if (ret_val) { - hw_dbg(hw, "NVM Read Error\n"); - return ret_val; - } - *pba_num |= data; - - return 0; -} - -/** - * ixgbe_get_mac_addr_generic - Generic get MAC address - * @hw: pointer to hardware structure - * @mac_addr: Adapter MAC address - * - * Reads the adapter's MAC address from first Receive Address Register (RAR0) - * A reset of the adapter must be performed prior to calling this function - * in order for the MAC address to have been loaded from the EEPROM into RAR0 - **/ -s32 ixgbe_get_mac_addr_generic(struct ixgbe_hw *hw, u8 *mac_addr) -{ - u32 rar_high; - u32 rar_low; - u16 i; - - rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(0)); - rar_low = IXGBE_READ_REG(hw, IXGBE_RAL(0)); - - for (i = 0; i < 4; i++) - mac_addr[i] = (u8)(rar_low >> (i*8)); - - for (i = 0; i < 2; i++) - mac_addr[i+4] = (u8)(rar_high >> (i*8)); - - return 0; -} - -/** - * ixgbe_get_bus_info_generic - Generic set PCI bus info - * @hw: pointer to hardware structure - * - * Sets the PCI bus info (speed, width, type) within the ixgbe_hw structure - **/ -s32 ixgbe_get_bus_info_generic(struct ixgbe_hw *hw) -{ - struct ixgbe_adapter *adapter = hw->back; - struct ixgbe_mac_info *mac = &hw->mac; - u16 link_status; - - hw->bus.type = ixgbe_bus_type_pci_express; - - /* Get the negotiated link width and speed from PCI config space */ - pci_read_config_word(adapter->pdev, IXGBE_PCI_LINK_STATUS, - &link_status); - - switch (link_status & IXGBE_PCI_LINK_WIDTH) { - case IXGBE_PCI_LINK_WIDTH_1: - hw->bus.width = ixgbe_bus_width_pcie_x1; - break; - case IXGBE_PCI_LINK_WIDTH_2: - hw->bus.width = ixgbe_bus_width_pcie_x2; - break; - case IXGBE_PCI_LINK_WIDTH_4: - hw->bus.width = ixgbe_bus_width_pcie_x4; - break; - case IXGBE_PCI_LINK_WIDTH_8: - hw->bus.width = ixgbe_bus_width_pcie_x8; - break; - default: - hw->bus.width = ixgbe_bus_width_unknown; - break; - } - - switch (link_status & IXGBE_PCI_LINK_SPEED) { - case IXGBE_PCI_LINK_SPEED_2500: - hw->bus.speed = ixgbe_bus_speed_2500; - break; - case IXGBE_PCI_LINK_SPEED_5000: - hw->bus.speed = ixgbe_bus_speed_5000; - break; - default: - hw->bus.speed = ixgbe_bus_speed_unknown; - break; - } - - mac->ops.set_lan_id(hw); - - return 0; -} - -/** - * ixgbe_set_lan_id_multi_port_pcie - Set LAN id for PCIe multiple port devices - * @hw: pointer to the HW structure - * - * Determines the LAN function id by reading memory-mapped registers - * and swaps the port value if requested. - **/ -void ixgbe_set_lan_id_multi_port_pcie(struct ixgbe_hw *hw) -{ - struct ixgbe_bus_info *bus = &hw->bus; - u32 reg; - - reg = IXGBE_READ_REG(hw, IXGBE_STATUS); - bus->func = (reg & IXGBE_STATUS_LAN_ID) >> IXGBE_STATUS_LAN_ID_SHIFT; - bus->lan_id = bus->func; - - /* check for a port swap */ - reg = IXGBE_READ_REG(hw, IXGBE_FACTPS); - if (reg & IXGBE_FACTPS_LFS) - bus->func ^= 0x1; -} - -/** - * ixgbe_stop_adapter_generic - Generic stop Tx/Rx units - * @hw: pointer to hardware structure - * - * Sets the adapter_stopped flag within ixgbe_hw struct. Clears interrupts, - * disables transmit and receive units. The adapter_stopped flag is used by - * the shared code and drivers to determine if the adapter is in a stopped - * state and should not touch the hardware. - **/ -s32 ixgbe_stop_adapter_generic(struct ixgbe_hw *hw) -{ - u32 number_of_queues; - u32 reg_val; - u16 i; - - /* - * Set the adapter_stopped flag so other driver functions stop touching - * the hardware - */ - hw->adapter_stopped = true; - - /* Disable the receive unit */ - reg_val = IXGBE_READ_REG(hw, IXGBE_RXCTRL); - reg_val &= ~(IXGBE_RXCTRL_RXEN); - IXGBE_WRITE_REG(hw, IXGBE_RXCTRL, reg_val); - IXGBE_WRITE_FLUSH(hw); - msleep(2); - - /* Clear interrupt mask to stop from interrupts being generated */ - IXGBE_WRITE_REG(hw, IXGBE_EIMC, IXGBE_IRQ_CLEAR_MASK); - - /* Clear any pending interrupts */ - IXGBE_READ_REG(hw, IXGBE_EICR); - - /* Disable the transmit unit. Each queue must be disabled. */ - number_of_queues = hw->mac.max_tx_queues; - for (i = 0; i < number_of_queues; i++) { - reg_val = IXGBE_READ_REG(hw, IXGBE_TXDCTL(i)); - if (reg_val & IXGBE_TXDCTL_ENABLE) { - reg_val &= ~IXGBE_TXDCTL_ENABLE; - IXGBE_WRITE_REG(hw, IXGBE_TXDCTL(i), reg_val); - } - } - - /* - * Prevent the PCI-E bus from from hanging by disabling PCI-E master - * access and verify no pending requests - */ - if (ixgbe_disable_pcie_master(hw) != 0) - hw_dbg(hw, "PCI-E Master disable polling has failed.\n"); - - return 0; -} - -/** - * ixgbe_led_on_generic - Turns on the software controllable LEDs. - * @hw: pointer to hardware structure - * @index: led number to turn on - **/ -s32 ixgbe_led_on_generic(struct ixgbe_hw *hw, u32 index) -{ - u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL); - - /* To turn on the LED, set mode to ON. */ - led_reg &= ~IXGBE_LED_MODE_MASK(index); - led_reg |= IXGBE_LED_ON << IXGBE_LED_MODE_SHIFT(index); - IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg); - IXGBE_WRITE_FLUSH(hw); - - return 0; -} - -/** - * ixgbe_led_off_generic - Turns off the software controllable LEDs. - * @hw: pointer to hardware structure - * @index: led number to turn off - **/ -s32 ixgbe_led_off_generic(struct ixgbe_hw *hw, u32 index) -{ - u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL); - - /* To turn off the LED, set mode to OFF. */ - led_reg &= ~IXGBE_LED_MODE_MASK(index); - led_reg |= IXGBE_LED_OFF << IXGBE_LED_MODE_SHIFT(index); - IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg); - IXGBE_WRITE_FLUSH(hw); - - return 0; -} - -/** - * ixgbe_init_eeprom_params_generic - Initialize EEPROM params - * @hw: pointer to hardware structure - * - * Initializes the EEPROM parameters ixgbe_eeprom_info within the - * ixgbe_hw struct in order to set up EEPROM access. - **/ -s32 ixgbe_init_eeprom_params_generic(struct ixgbe_hw *hw) -{ - struct ixgbe_eeprom_info *eeprom = &hw->eeprom; - u32 eec; - u16 eeprom_size; - - if (eeprom->type == ixgbe_eeprom_uninitialized) { - eeprom->type = ixgbe_eeprom_none; - /* Set default semaphore delay to 10ms which is a well - * tested value */ - eeprom->semaphore_delay = 10; - - /* - * Check for EEPROM present first. - * If not present leave as none - */ - eec = IXGBE_READ_REG(hw, IXGBE_EEC); - if (eec & IXGBE_EEC_PRES) { - eeprom->type = ixgbe_eeprom_spi; - - /* - * SPI EEPROM is assumed here. This code would need to - * change if a future EEPROM is not SPI. - */ - eeprom_size = (u16)((eec & IXGBE_EEC_SIZE) >> - IXGBE_EEC_SIZE_SHIFT); - eeprom->word_size = 1 << (eeprom_size + - IXGBE_EEPROM_WORD_SIZE_SHIFT); - } - - if (eec & IXGBE_EEC_ADDR_SIZE) - eeprom->address_bits = 16; - else - eeprom->address_bits = 8; - hw_dbg(hw, "Eeprom params: type = %d, size = %d, address bits: " - "%d\n", eeprom->type, eeprom->word_size, - eeprom->address_bits); - } - - return 0; -} - -/** - * ixgbe_write_eeprom_generic - Writes 16 bit value to EEPROM - * @hw: pointer to hardware structure - * @offset: offset within the EEPROM to be written to - * @data: 16 bit word to be written to the EEPROM - * - * If ixgbe_eeprom_update_checksum is not called after this function, the - * EEPROM will most likely contain an invalid checksum. - **/ -s32 ixgbe_write_eeprom_generic(struct ixgbe_hw *hw, u16 offset, u16 data) -{ - s32 status; - u8 write_opcode = IXGBE_EEPROM_WRITE_OPCODE_SPI; - - hw->eeprom.ops.init_params(hw); - - if (offset >= hw->eeprom.word_size) { - status = IXGBE_ERR_EEPROM; - goto out; - } - - /* Prepare the EEPROM for writing */ - status = ixgbe_acquire_eeprom(hw); - - if (status == 0) { - if (ixgbe_ready_eeprom(hw) != 0) { - ixgbe_release_eeprom(hw); - status = IXGBE_ERR_EEPROM; - } - } - - if (status == 0) { - ixgbe_standby_eeprom(hw); - - /* Send the WRITE ENABLE command (8 bit opcode ) */ - ixgbe_shift_out_eeprom_bits(hw, IXGBE_EEPROM_WREN_OPCODE_SPI, - IXGBE_EEPROM_OPCODE_BITS); - - ixgbe_standby_eeprom(hw); - - /* - * Some SPI eeproms use the 8th address bit embedded in the - * opcode - */ - if ((hw->eeprom.address_bits == 8) && (offset >= 128)) - write_opcode |= IXGBE_EEPROM_A8_OPCODE_SPI; - - /* Send the Write command (8-bit opcode + addr) */ - ixgbe_shift_out_eeprom_bits(hw, write_opcode, - IXGBE_EEPROM_OPCODE_BITS); - ixgbe_shift_out_eeprom_bits(hw, (u16)(offset*2), - hw->eeprom.address_bits); - - /* Send the data */ - data = (data >> 8) | (data << 8); - ixgbe_shift_out_eeprom_bits(hw, data, 16); - ixgbe_standby_eeprom(hw); - - msleep(hw->eeprom.semaphore_delay); - /* Done with writing - release the EEPROM */ - ixgbe_release_eeprom(hw); - } - -out: - return status; -} - -/** - * ixgbe_read_eeprom_bit_bang_generic - Read EEPROM word using bit-bang - * @hw: pointer to hardware structure - * @offset: offset within the EEPROM to be read - * @data: read 16 bit value from EEPROM - * - * Reads 16 bit value from EEPROM through bit-bang method - **/ -s32 ixgbe_read_eeprom_bit_bang_generic(struct ixgbe_hw *hw, u16 offset, - u16 *data) -{ - s32 status; - u16 word_in; - u8 read_opcode = IXGBE_EEPROM_READ_OPCODE_SPI; - - hw->eeprom.ops.init_params(hw); - - if (offset >= hw->eeprom.word_size) { - status = IXGBE_ERR_EEPROM; - goto out; - } - - /* Prepare the EEPROM for reading */ - status = ixgbe_acquire_eeprom(hw); - - if (status == 0) { - if (ixgbe_ready_eeprom(hw) != 0) { - ixgbe_release_eeprom(hw); - status = IXGBE_ERR_EEPROM; - } - } - - if (status == 0) { - ixgbe_standby_eeprom(hw); - - /* - * Some SPI eeproms use the 8th address bit embedded in the - * opcode - */ - if ((hw->eeprom.address_bits == 8) && (offset >= 128)) - read_opcode |= IXGBE_EEPROM_A8_OPCODE_SPI; - - /* Send the READ command (opcode + addr) */ - ixgbe_shift_out_eeprom_bits(hw, read_opcode, - IXGBE_EEPROM_OPCODE_BITS); - ixgbe_shift_out_eeprom_bits(hw, (u16)(offset*2), - hw->eeprom.address_bits); - - /* Read the data. */ - word_in = ixgbe_shift_in_eeprom_bits(hw, 16); - *data = (word_in >> 8) | (word_in << 8); - - /* End this read operation */ - ixgbe_release_eeprom(hw); - } - -out: - return status; -} - -/** - * ixgbe_read_eeprom_generic - Read EEPROM word using EERD - * @hw: pointer to hardware structure - * @offset: offset of word in the EEPROM to read - * @data: word read from the EEPROM - * - * Reads a 16 bit word from the EEPROM using the EERD register. - **/ -s32 ixgbe_read_eeprom_generic(struct ixgbe_hw *hw, u16 offset, u16 *data) -{ - u32 eerd; - s32 status; - - hw->eeprom.ops.init_params(hw); - - if (offset >= hw->eeprom.word_size) { - status = IXGBE_ERR_EEPROM; - goto out; - } - - eerd = (offset << IXGBE_EEPROM_READ_ADDR_SHIFT) + - IXGBE_EEPROM_READ_REG_START; - - IXGBE_WRITE_REG(hw, IXGBE_EERD, eerd); - status = ixgbe_poll_eeprom_eerd_done(hw); - - if (status == 0) - *data = (IXGBE_READ_REG(hw, IXGBE_EERD) >> - IXGBE_EEPROM_READ_REG_DATA); - else - hw_dbg(hw, "Eeprom read timed out\n"); - -out: - return status; -} - -/** - * ixgbe_poll_eeprom_eerd_done - Poll EERD status - * @hw: pointer to hardware structure - * - * Polls the status bit (bit 1) of the EERD to determine when the read is done. - **/ -static s32 ixgbe_poll_eeprom_eerd_done(struct ixgbe_hw *hw) -{ - u32 i; - u32 reg; - s32 status = IXGBE_ERR_EEPROM; - - for (i = 0; i < IXGBE_EERD_ATTEMPTS; i++) { - reg = IXGBE_READ_REG(hw, IXGBE_EERD); - if (reg & IXGBE_EEPROM_READ_REG_DONE) { - status = 0; - break; - } - udelay(5); - } - return status; -} - -/** - * ixgbe_acquire_eeprom - Acquire EEPROM using bit-bang - * @hw: pointer to hardware structure - * - * Prepares EEPROM for access using bit-bang method. This function should - * be called before issuing a command to the EEPROM. - **/ -static s32 ixgbe_acquire_eeprom(struct ixgbe_hw *hw) -{ - s32 status = 0; - u32 eec = 0; - u32 i; - - if (ixgbe_acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM) != 0) - status = IXGBE_ERR_SWFW_SYNC; - - if (status == 0) { - eec = IXGBE_READ_REG(hw, IXGBE_EEC); - - /* Request EEPROM Access */ - eec |= IXGBE_EEC_REQ; - IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); - - for (i = 0; i < IXGBE_EEPROM_GRANT_ATTEMPTS; i++) { - eec = IXGBE_READ_REG(hw, IXGBE_EEC); - if (eec & IXGBE_EEC_GNT) - break; - udelay(5); - } - - /* Release if grant not acquired */ - if (!(eec & IXGBE_EEC_GNT)) { - eec &= ~IXGBE_EEC_REQ; - IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); - hw_dbg(hw, "Could not acquire EEPROM grant\n"); - - ixgbe_release_swfw_sync(hw, IXGBE_GSSR_EEP_SM); - status = IXGBE_ERR_EEPROM; - } - } - - /* Setup EEPROM for Read/Write */ - if (status == 0) { - /* Clear CS and SK */ - eec &= ~(IXGBE_EEC_CS | IXGBE_EEC_SK); - IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); - IXGBE_WRITE_FLUSH(hw); - udelay(1); - } - return status; -} - -/** - * ixgbe_get_eeprom_semaphore - Get hardware semaphore - * @hw: pointer to hardware structure - * - * Sets the hardware semaphores so EEPROM access can occur for bit-bang method - **/ -static s32 ixgbe_get_eeprom_semaphore(struct ixgbe_hw *hw) -{ - s32 status = IXGBE_ERR_EEPROM; - u32 timeout; - u32 i; - u32 swsm; - - /* Set timeout value based on size of EEPROM */ - timeout = hw->eeprom.word_size + 1; - - /* Get SMBI software semaphore between device drivers first */ - for (i = 0; i < timeout; i++) { - /* - * If the SMBI bit is 0 when we read it, then the bit will be - * set and we have the semaphore - */ - swsm = IXGBE_READ_REG(hw, IXGBE_SWSM); - if (!(swsm & IXGBE_SWSM_SMBI)) { - status = 0; - break; - } - msleep(1); - } - - /* Now get the semaphore between SW/FW through the SWESMBI bit */ - if (status == 0) { - for (i = 0; i < timeout; i++) { - swsm = IXGBE_READ_REG(hw, IXGBE_SWSM); - - /* Set the SW EEPROM semaphore bit to request access */ - swsm |= IXGBE_SWSM_SWESMBI; - IXGBE_WRITE_REG(hw, IXGBE_SWSM, swsm); - - /* - * If we set the bit successfully then we got the - * semaphore. - */ - swsm = IXGBE_READ_REG(hw, IXGBE_SWSM); - if (swsm & IXGBE_SWSM_SWESMBI) - break; - - udelay(50); - } - - /* - * Release semaphores and return error if SW EEPROM semaphore - * was not granted because we don't have access to the EEPROM - */ - if (i >= timeout) { - hw_dbg(hw, "Driver can't access the Eeprom - Semaphore " - "not granted.\n"); - ixgbe_release_eeprom_semaphore(hw); - status = IXGBE_ERR_EEPROM; - } - } - - return status; -} - -/** - * ixgbe_release_eeprom_semaphore - Release hardware semaphore - * @hw: pointer to hardware structure - * - * This function clears hardware semaphore bits. - **/ -static void ixgbe_release_eeprom_semaphore(struct ixgbe_hw *hw) -{ - u32 swsm; - - swsm = IXGBE_READ_REG(hw, IXGBE_SWSM); - - /* Release both semaphores by writing 0 to the bits SWESMBI and SMBI */ - swsm &= ~(IXGBE_SWSM_SWESMBI | IXGBE_SWSM_SMBI); - IXGBE_WRITE_REG(hw, IXGBE_SWSM, swsm); - IXGBE_WRITE_FLUSH(hw); -} - -/** - * ixgbe_ready_eeprom - Polls for EEPROM ready - * @hw: pointer to hardware structure - **/ -static s32 ixgbe_ready_eeprom(struct ixgbe_hw *hw) -{ - s32 status = 0; - u16 i; - u8 spi_stat_reg; - - /* - * Read "Status Register" repeatedly until the LSB is cleared. The - * EEPROM will signal that the command has been completed by clearing - * bit 0 of the internal status register. If it's not cleared within - * 5 milliseconds, then error out. - */ - for (i = 0; i < IXGBE_EEPROM_MAX_RETRY_SPI; i += 5) { - ixgbe_shift_out_eeprom_bits(hw, IXGBE_EEPROM_RDSR_OPCODE_SPI, - IXGBE_EEPROM_OPCODE_BITS); - spi_stat_reg = (u8)ixgbe_shift_in_eeprom_bits(hw, 8); - if (!(spi_stat_reg & IXGBE_EEPROM_STATUS_RDY_SPI)) - break; - - udelay(5); - ixgbe_standby_eeprom(hw); - }; - - /* - * On some parts, SPI write time could vary from 0-20mSec on 3.3V - * devices (and only 0-5mSec on 5V devices) - */ - if (i >= IXGBE_EEPROM_MAX_RETRY_SPI) { - hw_dbg(hw, "SPI EEPROM Status error\n"); - status = IXGBE_ERR_EEPROM; - } - - return status; -} - -/** - * ixgbe_standby_eeprom - Returns EEPROM to a "standby" state - * @hw: pointer to hardware structure - **/ -static void ixgbe_standby_eeprom(struct ixgbe_hw *hw) -{ - u32 eec; - - eec = IXGBE_READ_REG(hw, IXGBE_EEC); - - /* Toggle CS to flush commands */ - eec |= IXGBE_EEC_CS; - IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); - IXGBE_WRITE_FLUSH(hw); - udelay(1); - eec &= ~IXGBE_EEC_CS; - IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); - IXGBE_WRITE_FLUSH(hw); - udelay(1); -} - -/** - * ixgbe_shift_out_eeprom_bits - Shift data bits out to the EEPROM. - * @hw: pointer to hardware structure - * @data: data to send to the EEPROM - * @count: number of bits to shift out - **/ -static void ixgbe_shift_out_eeprom_bits(struct ixgbe_hw *hw, u16 data, - u16 count) -{ - u32 eec; - u32 mask; - u32 i; - - eec = IXGBE_READ_REG(hw, IXGBE_EEC); - - /* - * Mask is used to shift "count" bits of "data" out to the EEPROM - * one bit at a time. Determine the starting bit based on count - */ - mask = 0x01 << (count - 1); - - for (i = 0; i < count; i++) { - /* - * A "1" is shifted out to the EEPROM by setting bit "DI" to a - * "1", and then raising and then lowering the clock (the SK - * bit controls the clock input to the EEPROM). A "0" is - * shifted out to the EEPROM by setting "DI" to "0" and then - * raising and then lowering the clock. - */ - if (data & mask) - eec |= IXGBE_EEC_DI; - else - eec &= ~IXGBE_EEC_DI; - - IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); - IXGBE_WRITE_FLUSH(hw); - - udelay(1); - - ixgbe_raise_eeprom_clk(hw, &eec); - ixgbe_lower_eeprom_clk(hw, &eec); - - /* - * Shift mask to signify next bit of data to shift in to the - * EEPROM - */ - mask = mask >> 1; - }; - - /* We leave the "DI" bit set to "0" when we leave this routine. */ - eec &= ~IXGBE_EEC_DI; - IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); - IXGBE_WRITE_FLUSH(hw); -} - -/** - * ixgbe_shift_in_eeprom_bits - Shift data bits in from the EEPROM - * @hw: pointer to hardware structure - **/ -static u16 ixgbe_shift_in_eeprom_bits(struct ixgbe_hw *hw, u16 count) -{ - u32 eec; - u32 i; - u16 data = 0; - - /* - * In order to read a register from the EEPROM, we need to shift - * 'count' bits in from the EEPROM. Bits are "shifted in" by raising - * the clock input to the EEPROM (setting the SK bit), and then reading - * the value of the "DO" bit. During this "shifting in" process the - * "DI" bit should always be clear. - */ - eec = IXGBE_READ_REG(hw, IXGBE_EEC); - - eec &= ~(IXGBE_EEC_DO | IXGBE_EEC_DI); - - for (i = 0; i < count; i++) { - data = data << 1; - ixgbe_raise_eeprom_clk(hw, &eec); - - eec = IXGBE_READ_REG(hw, IXGBE_EEC); - - eec &= ~(IXGBE_EEC_DI); - if (eec & IXGBE_EEC_DO) - data |= 1; - - ixgbe_lower_eeprom_clk(hw, &eec); - } - - return data; -} - -/** - * ixgbe_raise_eeprom_clk - Raises the EEPROM's clock input. - * @hw: pointer to hardware structure - * @eec: EEC register's current value - **/ -static void ixgbe_raise_eeprom_clk(struct ixgbe_hw *hw, u32 *eec) -{ - /* - * Raise the clock input to the EEPROM - * (setting the SK bit), then delay - */ - *eec = *eec | IXGBE_EEC_SK; - IXGBE_WRITE_REG(hw, IXGBE_EEC, *eec); - IXGBE_WRITE_FLUSH(hw); - udelay(1); -} - -/** - * ixgbe_lower_eeprom_clk - Lowers the EEPROM's clock input. - * @hw: pointer to hardware structure - * @eecd: EECD's current value - **/ -static void ixgbe_lower_eeprom_clk(struct ixgbe_hw *hw, u32 *eec) -{ - /* - * Lower the clock input to the EEPROM (clearing the SK bit), then - * delay - */ - *eec = *eec & ~IXGBE_EEC_SK; - IXGBE_WRITE_REG(hw, IXGBE_EEC, *eec); - IXGBE_WRITE_FLUSH(hw); - udelay(1); -} - -/** - * ixgbe_release_eeprom - Release EEPROM, release semaphores - * @hw: pointer to hardware structure - **/ -static void ixgbe_release_eeprom(struct ixgbe_hw *hw) -{ - u32 eec; - - eec = IXGBE_READ_REG(hw, IXGBE_EEC); - - eec |= IXGBE_EEC_CS; /* Pull CS high */ - eec &= ~IXGBE_EEC_SK; /* Lower SCK */ - - IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); - IXGBE_WRITE_FLUSH(hw); - - udelay(1); - - /* Stop requesting EEPROM access */ - eec &= ~IXGBE_EEC_REQ; - IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); - - ixgbe_release_swfw_sync(hw, IXGBE_GSSR_EEP_SM); -} - -/** - * ixgbe_calc_eeprom_checksum - Calculates and returns the checksum - * @hw: pointer to hardware structure - **/ -static u16 ixgbe_calc_eeprom_checksum(struct ixgbe_hw *hw) -{ - u16 i; - u16 j; - u16 checksum = 0; - u16 length = 0; - u16 pointer = 0; - u16 word = 0; - - /* Include 0x0-0x3F in the checksum */ - for (i = 0; i < IXGBE_EEPROM_CHECKSUM; i++) { - if (hw->eeprom.ops.read(hw, i, &word) != 0) { - hw_dbg(hw, "EEPROM read failed\n"); - break; - } - checksum += word; - } - - /* Include all data from pointers except for the fw pointer */ - for (i = IXGBE_PCIE_ANALOG_PTR; i < IXGBE_FW_PTR; i++) { - hw->eeprom.ops.read(hw, i, &pointer); - - /* Make sure the pointer seems valid */ - if (pointer != 0xFFFF && pointer != 0) { - hw->eeprom.ops.read(hw, pointer, &length); - - if (length != 0xFFFF && length != 0) { - for (j = pointer+1; j <= pointer+length; j++) { - hw->eeprom.ops.read(hw, j, &word); - checksum += word; - } - } - } - } - - checksum = (u16)IXGBE_EEPROM_SUM - checksum; - - return checksum; -} - -/** - * ixgbe_validate_eeprom_checksum_generic - Validate EEPROM checksum - * @hw: pointer to hardware structure - * @checksum_val: calculated checksum - * - * Performs checksum calculation and validates the EEPROM checksum. If the - * caller does not need checksum_val, the value can be NULL. - **/ -s32 ixgbe_validate_eeprom_checksum_generic(struct ixgbe_hw *hw, - u16 *checksum_val) -{ - s32 status; - u16 checksum; - u16 read_checksum = 0; - - /* - * Read the first word from the EEPROM. If this times out or fails, do - * not continue or we could be in for a very long wait while every - * EEPROM read fails - */ - status = hw->eeprom.ops.read(hw, 0, &checksum); - - if (status == 0) { - checksum = ixgbe_calc_eeprom_checksum(hw); - - hw->eeprom.ops.read(hw, IXGBE_EEPROM_CHECKSUM, &read_checksum); - - /* - * Verify read checksum from EEPROM is the same as - * calculated checksum - */ - if (read_checksum != checksum) - status = IXGBE_ERR_EEPROM_CHECKSUM; - - /* If the user cares, return the calculated checksum */ - if (checksum_val) - *checksum_val = checksum; - } else { - hw_dbg(hw, "EEPROM read failed\n"); - } - - return status; -} - -/** - * ixgbe_update_eeprom_checksum_generic - Updates the EEPROM checksum - * @hw: pointer to hardware structure - **/ -s32 ixgbe_update_eeprom_checksum_generic(struct ixgbe_hw *hw) -{ - s32 status; - u16 checksum; - - /* - * Read the first word from the EEPROM. If this times out or fails, do - * not continue or we could be in for a very long wait while every - * EEPROM read fails - */ - status = hw->eeprom.ops.read(hw, 0, &checksum); - - if (status == 0) { - checksum = ixgbe_calc_eeprom_checksum(hw); - status = hw->eeprom.ops.write(hw, IXGBE_EEPROM_CHECKSUM, - checksum); - } else { - hw_dbg(hw, "EEPROM read failed\n"); - } - - return status; -} - -/** - * ixgbe_validate_mac_addr - Validate MAC address - * @mac_addr: pointer to MAC address. - * - * Tests a MAC address to ensure it is a valid Individual Address - **/ -s32 ixgbe_validate_mac_addr(u8 *mac_addr) -{ - s32 status = 0; - - /* Make sure it is not a multicast address */ - if (IXGBE_IS_MULTICAST(mac_addr)) - status = IXGBE_ERR_INVALID_MAC_ADDR; - /* Not a broadcast address */ - else if (IXGBE_IS_BROADCAST(mac_addr)) - status = IXGBE_ERR_INVALID_MAC_ADDR; - /* Reject the zero address */ - else if (mac_addr[0] == 0 && mac_addr[1] == 0 && mac_addr[2] == 0 && - mac_addr[3] == 0 && mac_addr[4] == 0 && mac_addr[5] == 0) - status = IXGBE_ERR_INVALID_MAC_ADDR; - - return status; -} - -/** - * ixgbe_set_rar_generic - Set Rx address register - * @hw: pointer to hardware structure - * @index: Receive address register to write - * @addr: Address to put into receive address register - * @vmdq: VMDq "set" or "pool" index - * @enable_addr: set flag that address is active - * - * Puts an ethernet address into a receive address register. - **/ -s32 ixgbe_set_rar_generic(struct ixgbe_hw *hw, u32 index, u8 *addr, u32 vmdq, - u32 enable_addr) -{ - u32 rar_low, rar_high; - u32 rar_entries = hw->mac.num_rar_entries; - - /* setup VMDq pool selection before this RAR gets enabled */ - hw->mac.ops.set_vmdq(hw, index, vmdq); - - /* Make sure we are using a valid rar index range */ - if (index < rar_entries) { - /* - * HW expects these in little endian so we reverse the byte - * order from network order (big endian) to little endian - */ - rar_low = ((u32)addr[0] | - ((u32)addr[1] << 8) | - ((u32)addr[2] << 16) | - ((u32)addr[3] << 24)); - /* - * Some parts put the VMDq setting in the extra RAH bits, - * so save everything except the lower 16 bits that hold part - * of the address and the address valid bit. - */ - rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(index)); - rar_high &= ~(0x0000FFFF | IXGBE_RAH_AV); - rar_high |= ((u32)addr[4] | ((u32)addr[5] << 8)); - - if (enable_addr != 0) - rar_high |= IXGBE_RAH_AV; - - IXGBE_WRITE_REG(hw, IXGBE_RAL(index), rar_low); - IXGBE_WRITE_REG(hw, IXGBE_RAH(index), rar_high); - } else { - hw_dbg(hw, "RAR index %d is out of range.\n", index); - } - - return 0; -} - -/** - * ixgbe_clear_rar_generic - Remove Rx address register - * @hw: pointer to hardware structure - * @index: Receive address register to write - * - * Clears an ethernet address from a receive address register. - **/ -s32 ixgbe_clear_rar_generic(struct ixgbe_hw *hw, u32 index) -{ - u32 rar_high; - u32 rar_entries = hw->mac.num_rar_entries; - - /* Make sure we are using a valid rar index range */ - if (index < rar_entries) { - /* - * Some parts put the VMDq setting in the extra RAH bits, - * so save everything except the lower 16 bits that hold part - * of the address and the address valid bit. - */ - rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(index)); - rar_high &= ~(0x0000FFFF | IXGBE_RAH_AV); - - IXGBE_WRITE_REG(hw, IXGBE_RAL(index), 0); - IXGBE_WRITE_REG(hw, IXGBE_RAH(index), rar_high); - } else { - hw_dbg(hw, "RAR index %d is out of range.\n", index); - } - - /* clear VMDq pool/queue selection for this RAR */ - hw->mac.ops.clear_vmdq(hw, index, IXGBE_CLEAR_VMDQ_ALL); - - return 0; -} - -/** - * ixgbe_enable_rar - Enable Rx address register - * @hw: pointer to hardware structure - * @index: index into the RAR table - * - * Enables the select receive address register. - **/ -static void ixgbe_enable_rar(struct ixgbe_hw *hw, u32 index) -{ - u32 rar_high; - - rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(index)); - rar_high |= IXGBE_RAH_AV; - IXGBE_WRITE_REG(hw, IXGBE_RAH(index), rar_high); -} - -/** - * ixgbe_disable_rar - Disable Rx address register - * @hw: pointer to hardware structure - * @index: index into the RAR table - * - * Disables the select receive address register. - **/ -static void ixgbe_disable_rar(struct ixgbe_hw *hw, u32 index) -{ - u32 rar_high; - - rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(index)); - rar_high &= (~IXGBE_RAH_AV); - IXGBE_WRITE_REG(hw, IXGBE_RAH(index), rar_high); -} - -/** - * ixgbe_init_rx_addrs_generic - Initializes receive address filters. - * @hw: pointer to hardware structure - * - * Places the MAC address in receive address register 0 and clears the rest - * of the receive address registers. Clears the multicast table. Assumes - * the receiver is in reset when the routine is called. - **/ -s32 ixgbe_init_rx_addrs_generic(struct ixgbe_hw *hw) -{ - u32 i; - u32 rar_entries = hw->mac.num_rar_entries; - - /* - * If the current mac address is valid, assume it is a software override - * to the permanent address. - * Otherwise, use the permanent address from the eeprom. - */ - if (ixgbe_validate_mac_addr(hw->mac.addr) == - IXGBE_ERR_INVALID_MAC_ADDR) { - /* Get the MAC address from the RAR0 for later reference */ - hw->mac.ops.get_mac_addr(hw, hw->mac.addr); - - hw_dbg(hw, " Keeping Current RAR0 Addr =%.2X %.2X %.2X ", - hw->mac.addr[0], hw->mac.addr[1], - hw->mac.addr[2]); - hw_dbg(hw, "%.2X %.2X %.2X\n", hw->mac.addr[3], - hw->mac.addr[4], hw->mac.addr[5]); - } else { - /* Setup the receive address. */ - hw_dbg(hw, "Overriding MAC Address in RAR[0]\n"); - hw_dbg(hw, " New MAC Addr =%.2X %.2X %.2X ", - hw->mac.addr[0], hw->mac.addr[1], - hw->mac.addr[2]); - hw_dbg(hw, "%.2X %.2X %.2X\n", hw->mac.addr[3], - hw->mac.addr[4], hw->mac.addr[5]); - - hw->mac.ops.set_rar(hw, 0, hw->mac.addr, 0, IXGBE_RAH_AV); - } - hw->addr_ctrl.overflow_promisc = 0; - - hw->addr_ctrl.rar_used_count = 1; - - /* Zero out the other receive addresses. */ - hw_dbg(hw, "Clearing RAR[1-%d]\n", rar_entries - 1); - for (i = 1; i < rar_entries; i++) { - IXGBE_WRITE_REG(hw, IXGBE_RAL(i), 0); - IXGBE_WRITE_REG(hw, IXGBE_RAH(i), 0); - } - - /* Clear the MTA */ - hw->addr_ctrl.mc_addr_in_rar_count = 0; - hw->addr_ctrl.mta_in_use = 0; - IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL, hw->mac.mc_filter_type); - - hw_dbg(hw, " Clearing MTA\n"); - for (i = 0; i < hw->mac.mcft_size; i++) - IXGBE_WRITE_REG(hw, IXGBE_MTA(i), 0); - - if (hw->mac.ops.init_uta_tables) - hw->mac.ops.init_uta_tables(hw); - - return 0; -} - -/** - * ixgbe_add_uc_addr - Adds a secondary unicast address. - * @hw: pointer to hardware structure - * @addr: new address - * - * Adds it to unused receive address register or goes into promiscuous mode. - **/ -static void ixgbe_add_uc_addr(struct ixgbe_hw *hw, u8 *addr, u32 vmdq) -{ - u32 rar_entries = hw->mac.num_rar_entries; - u32 rar; - - hw_dbg(hw, " UC Addr = %.2X %.2X %.2X %.2X %.2X %.2X\n", - addr[0], addr[1], addr[2], addr[3], addr[4], addr[5]); - - /* - * Place this address in the RAR if there is room, - * else put the controller into promiscuous mode - */ - if (hw->addr_ctrl.rar_used_count < rar_entries) { - rar = hw->addr_ctrl.rar_used_count - - hw->addr_ctrl.mc_addr_in_rar_count; - hw->mac.ops.set_rar(hw, rar, addr, vmdq, IXGBE_RAH_AV); - hw_dbg(hw, "Added a secondary address to RAR[%d]\n", rar); - hw->addr_ctrl.rar_used_count++; - } else { - hw->addr_ctrl.overflow_promisc++; - } - - hw_dbg(hw, "ixgbe_add_uc_addr Complete\n"); -} - -/** - * ixgbe_update_uc_addr_list_generic - Updates MAC list of secondary addresses - * @hw: pointer to hardware structure - * @addr_list: the list of new addresses - * @addr_count: number of addresses - * @next: iterator function to walk the address list - * - * The given list replaces any existing list. Clears the secondary addrs from - * receive address registers. Uses unused receive address registers for the - * first secondary addresses, and falls back to promiscuous mode as needed. - * - * Drivers using secondary unicast addresses must set user_set_promisc when - * manually putting the device into promiscuous mode. - **/ -s32 ixgbe_update_uc_addr_list_generic(struct ixgbe_hw *hw, u8 *addr_list, - u32 addr_count, ixgbe_mc_addr_itr next) -{ - u8 *addr; - u32 i; - u32 old_promisc_setting = hw->addr_ctrl.overflow_promisc; - u32 uc_addr_in_use; - u32 fctrl; - u32 vmdq; - - /* - * Clear accounting of old secondary address list, - * don't count RAR[0] - */ - uc_addr_in_use = hw->addr_ctrl.rar_used_count - 1; - hw->addr_ctrl.rar_used_count -= uc_addr_in_use; - hw->addr_ctrl.overflow_promisc = 0; - - /* Zero out the other receive addresses */ - hw_dbg(hw, "Clearing RAR[1-%d]\n", uc_addr_in_use); - for (i = 1; i <= uc_addr_in_use; i++) { - IXGBE_WRITE_REG(hw, IXGBE_RAL(i), 0); - IXGBE_WRITE_REG(hw, IXGBE_RAH(i), 0); - } - - /* Add the new addresses */ - for (i = 0; i < addr_count; i++) { - hw_dbg(hw, " Adding the secondary addresses:\n"); - addr = next(hw, &addr_list, &vmdq); - ixgbe_add_uc_addr(hw, addr, vmdq); - } - - if (hw->addr_ctrl.overflow_promisc) { - /* enable promisc if not already in overflow or set by user */ - if (!old_promisc_setting && !hw->addr_ctrl.user_set_promisc) { - hw_dbg(hw, " Entering address overflow promisc mode\n"); - fctrl = IXGBE_READ_REG(hw, IXGBE_FCTRL); - fctrl |= IXGBE_FCTRL_UPE; - IXGBE_WRITE_REG(hw, IXGBE_FCTRL, fctrl); - } - } else { - /* only disable if set by overflow, not by user */ - if (old_promisc_setting && !hw->addr_ctrl.user_set_promisc) { - hw_dbg(hw, " Leaving address overflow promisc mode\n"); - fctrl = IXGBE_READ_REG(hw, IXGBE_FCTRL); - fctrl &= ~IXGBE_FCTRL_UPE; - IXGBE_WRITE_REG(hw, IXGBE_FCTRL, fctrl); - } - } - - hw_dbg(hw, "ixgbe_update_uc_addr_list_generic Complete\n"); - return 0; -} - -/** - * ixgbe_mta_vector - Determines bit-vector in multicast table to set - * @hw: pointer to hardware structure - * @mc_addr: the multicast address - * - * Extracts the 12 bits, from a multicast address, to determine which - * bit-vector to set in the multicast table. The hardware uses 12 bits, from - * incoming rx multicast addresses, to determine the bit-vector to check in - * the MTA. Which of the 4 combination, of 12-bits, the hardware uses is set - * by the MO field of the MCSTCTRL. The MO field is set during initialization - * to mc_filter_type. - **/ -static s32 ixgbe_mta_vector(struct ixgbe_hw *hw, u8 *mc_addr) -{ - u32 vector = 0; - - switch (hw->mac.mc_filter_type) { - case 0: /* use bits [47:36] of the address */ - vector = ((mc_addr[4] >> 4) | (((u16)mc_addr[5]) << 4)); - break; - case 1: /* use bits [46:35] of the address */ - vector = ((mc_addr[4] >> 3) | (((u16)mc_addr[5]) << 5)); - break; - case 2: /* use bits [45:34] of the address */ - vector = ((mc_addr[4] >> 2) | (((u16)mc_addr[5]) << 6)); - break; - case 3: /* use bits [43:32] of the address */ - vector = ((mc_addr[4]) | (((u16)mc_addr[5]) << 8)); - break; - default: /* Invalid mc_filter_type */ - hw_dbg(hw, "MC filter type param set incorrectly\n"); - break; - } - - /* vector can only be 12-bits or boundary will be exceeded */ - vector &= 0xFFF; - return vector; -} - -/** - * ixgbe_set_mta - Set bit-vector in multicast table - * @hw: pointer to hardware structure - * @hash_value: Multicast address hash value - * - * Sets the bit-vector in the multicast table. - **/ -static void ixgbe_set_mta(struct ixgbe_hw *hw, u8 *mc_addr) -{ - u32 vector; - u32 vector_bit; - u32 vector_reg; - u32 mta_reg; - - hw->addr_ctrl.mta_in_use++; - - vector = ixgbe_mta_vector(hw, mc_addr); - hw_dbg(hw, " bit-vector = 0x%03X\n", vector); - - /* - * The MTA is a register array of 128 32-bit registers. It is treated - * like an array of 4096 bits. We want to set bit - * BitArray[vector_value]. So we figure out what register the bit is - * in, read it, OR in the new bit, then write back the new value. The - * register is determined by the upper 7 bits of the vector value and - * the bit within that register are determined by the lower 5 bits of - * the value. - */ - vector_reg = (vector >> 5) & 0x7F; - vector_bit = vector & 0x1F; - mta_reg = IXGBE_READ_REG(hw, IXGBE_MTA(vector_reg)); - mta_reg |= (1 << vector_bit); - IXGBE_WRITE_REG(hw, IXGBE_MTA(vector_reg), mta_reg); -} - -/** - * ixgbe_update_mc_addr_list_generic - Updates MAC list of multicast addresses - * @hw: pointer to hardware structure - * @mc_addr_list: the list of new multicast addresses - * @mc_addr_count: number of addresses - * @next: iterator function to walk the multicast address list - * - * The given list replaces any existing list. Clears the MC addrs from receive - * address registers and the multicast table. Uses unused receive address - * registers for the first multicast addresses, and hashes the rest into the - * multicast table. - **/ -s32 ixgbe_update_mc_addr_list_generic(struct ixgbe_hw *hw, u8 *mc_addr_list, - u32 mc_addr_count, ixgbe_mc_addr_itr next) -{ - u32 i; - u32 vmdq; - - /* - * Set the new number of MC addresses that we are being requested to - * use. - */ - hw->addr_ctrl.num_mc_addrs = mc_addr_count; - hw->addr_ctrl.mta_in_use = 0; - - /* Clear the MTA */ - hw_dbg(hw, " Clearing MTA\n"); - for (i = 0; i < hw->mac.mcft_size; i++) - IXGBE_WRITE_REG(hw, IXGBE_MTA(i), 0); - - /* Add the new addresses */ - for (i = 0; i < mc_addr_count; i++) { - hw_dbg(hw, " Adding the multicast addresses:\n"); - ixgbe_set_mta(hw, next(hw, &mc_addr_list, &vmdq)); - } - - /* Enable mta */ - if (hw->addr_ctrl.mta_in_use > 0) - IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL, - IXGBE_MCSTCTRL_MFE | hw->mac.mc_filter_type); - - hw_dbg(hw, "ixgbe_update_mc_addr_list_generic Complete\n"); - return 0; -} - -/** - * ixgbe_enable_mc_generic - Enable multicast address in RAR - * @hw: pointer to hardware structure - * - * Enables multicast address in RAR and the use of the multicast hash table. - **/ -s32 ixgbe_enable_mc_generic(struct ixgbe_hw *hw) -{ - u32 i; - u32 rar_entries = hw->mac.num_rar_entries; - struct ixgbe_addr_filter_info *a = &hw->addr_ctrl; - - if (a->mc_addr_in_rar_count > 0) - for (i = (rar_entries - a->mc_addr_in_rar_count); - i < rar_entries; i++) - ixgbe_enable_rar(hw, i); - - if (a->mta_in_use > 0) - IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL, IXGBE_MCSTCTRL_MFE | - hw->mac.mc_filter_type); - - return 0; -} - -/** - * ixgbe_disable_mc_generic - Disable multicast address in RAR - * @hw: pointer to hardware structure - * - * Disables multicast address in RAR and the use of the multicast hash table. - **/ -s32 ixgbe_disable_mc_generic(struct ixgbe_hw *hw) -{ - u32 i; - u32 rar_entries = hw->mac.num_rar_entries; - struct ixgbe_addr_filter_info *a = &hw->addr_ctrl; - - if (a->mc_addr_in_rar_count > 0) - for (i = (rar_entries - a->mc_addr_in_rar_count); - i < rar_entries; i++) - ixgbe_disable_rar(hw, i); - - if (a->mta_in_use > 0) - IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL, hw->mac.mc_filter_type); - - return 0; -} - -/** - * ixgbe_fc_enable - Enable flow control - * @hw: pointer to hardware structure - * @packetbuf_num: packet buffer number (0-7) - * - * Enable flow control according to the current settings. - **/ -s32 ixgbe_fc_enable(struct ixgbe_hw *hw, s32 packetbuf_num) -{ - s32 ret_val = 0; - u32 mflcn_reg; - u32 fccfg_reg; - u32 reg; - - mflcn_reg = IXGBE_READ_REG(hw, IXGBE_MFLCN); - mflcn_reg &= ~(IXGBE_MFLCN_RFCE | IXGBE_MFLCN_RPFCE); - - fccfg_reg = IXGBE_READ_REG(hw, IXGBE_FCCFG); - fccfg_reg &= ~(IXGBE_FCCFG_TFCE_802_3X | IXGBE_FCCFG_TFCE_PRIORITY); - - /* - * The possible values of fc.current_mode are: - * 0: Flow control is completely disabled - * 1: Rx flow control is enabled (we can receive pause frames, - * but not send pause frames). - * 2: Tx flow control is enabled (we can send pause frames but - * we do not support receiving pause frames). - * 3: Both Rx and Tx flow control (symmetric) are enabled. - * 4: Priority Flow Control is enabled. - * other: Invalid. - */ - switch (hw->fc.current_mode) { - case ixgbe_fc_none: - /* Flow control completely disabled by software override. */ - break; - case ixgbe_fc_rx_pause: - /* - * Rx Flow control is enabled and Tx Flow control is - * disabled by software override. Since there really - * isn't a way to advertise that we are capable of RX - * Pause ONLY, we will advertise that we support both - * symmetric and asymmetric Rx PAUSE. Later, we will - * disable the adapter's ability to send PAUSE frames. - */ - mflcn_reg |= IXGBE_MFLCN_RFCE; - break; - case ixgbe_fc_tx_pause: - /* - * Tx Flow control is enabled, and Rx Flow control is - * disabled by software override. - */ - fccfg_reg |= IXGBE_FCCFG_TFCE_802_3X; - break; - case ixgbe_fc_full: - /* Flow control (both Rx and Tx) is enabled by SW override. */ - mflcn_reg |= IXGBE_MFLCN_RFCE; - fccfg_reg |= IXGBE_FCCFG_TFCE_802_3X; - break; -#ifdef CONFIG_DCB - case ixgbe_fc_pfc: - goto out; - break; -#endif - default: - hw_dbg(hw, "Flow control param set incorrectly\n"); - ret_val = -IXGBE_ERR_CONFIG; - goto out; - break; - } - - /* Enable 802.3x based flow control settings. */ - IXGBE_WRITE_REG(hw, IXGBE_MFLCN, mflcn_reg); - IXGBE_WRITE_REG(hw, IXGBE_FCCFG, fccfg_reg); - - /* Set up and enable Rx high/low water mark thresholds, enable XON. */ - if (hw->fc.current_mode & ixgbe_fc_tx_pause) { - if (hw->fc.send_xon) - IXGBE_WRITE_REG(hw, IXGBE_FCRTL_82599(packetbuf_num), - (hw->fc.low_water | IXGBE_FCRTL_XONE)); - else - IXGBE_WRITE_REG(hw, IXGBE_FCRTL_82599(packetbuf_num), - hw->fc.low_water); - - IXGBE_WRITE_REG(hw, IXGBE_FCRTH_82599(packetbuf_num), - (hw->fc.high_water | IXGBE_FCRTH_FCEN)); - } - - /* Configure pause time (2 TCs per register) */ - reg = IXGBE_READ_REG(hw, IXGBE_FCTTV(packetbuf_num)); - if ((packetbuf_num & 1) == 0) - reg = (reg & 0xFFFF0000) | hw->fc.pause_time; - else - reg = (reg & 0x0000FFFF) | (hw->fc.pause_time << 16); - IXGBE_WRITE_REG(hw, IXGBE_FCTTV(packetbuf_num / 2), reg); - - IXGBE_WRITE_REG(hw, IXGBE_FCRTV, (hw->fc.pause_time >> 1)); - -out: - return ret_val; -} - -/** - * ixgbe_fc_autoneg - Configure flow control - * @hw: pointer to hardware structure - * - * Negotiates flow control capabilities with link partner using autoneg and - * applies the results. - **/ -s32 ixgbe_fc_autoneg(struct ixgbe_hw *hw) -{ - s32 ret_val = 0; - u32 i, reg, pcs_anadv_reg, pcs_lpab_reg; - - reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA); - - /* - * The possible values of fc.current_mode are: - * 0: Flow control is completely disabled - * 1: Rx flow control is enabled (we can receive pause frames, - * but not send pause frames). - * 2: Tx flow control is enabled (we can send pause frames but - * we do not support receiving pause frames). - * 3: Both Rx and Tx flow control (symmetric) are enabled. - * 4: Priority Flow Control is enabled. - * other: Invalid. - */ - switch (hw->fc.current_mode) { - case ixgbe_fc_none: - /* Flow control completely disabled by software override. */ - reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE); - break; - case ixgbe_fc_rx_pause: - /* - * Rx Flow control is enabled and Tx Flow control is - * disabled by software override. Since there really - * isn't a way to advertise that we are capable of RX - * Pause ONLY, we will advertise that we support both - * symmetric and asymmetric Rx PAUSE. Later, we will - * disable the adapter's ability to send PAUSE frames. - */ - reg |= (IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE); - break; - case ixgbe_fc_tx_pause: - /* - * Tx Flow control is enabled, and Rx Flow control is - * disabled by software override. - */ - reg |= (IXGBE_PCS1GANA_ASM_PAUSE); - reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE); - break; - case ixgbe_fc_full: - /* Flow control (both Rx and Tx) is enabled by SW override. */ - reg |= (IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE); - break; -#ifdef CONFIG_DCB - case ixgbe_fc_pfc: - goto out; - break; -#endif - default: - hw_dbg(hw, "Flow control param set incorrectly\n"); - ret_val = -IXGBE_ERR_CONFIG; - goto out; - break; - } - - IXGBE_WRITE_REG(hw, IXGBE_PCS1GANA, reg); - reg = IXGBE_READ_REG(hw, IXGBE_PCS1GLCTL); - - /* Set PCS register for autoneg */ - /* Enable and restart autoneg */ - reg |= IXGBE_PCS1GLCTL_AN_ENABLE | IXGBE_PCS1GLCTL_AN_RESTART; - - /* Disable AN timeout */ - if (hw->fc.strict_ieee) - reg &= ~IXGBE_PCS1GLCTL_AN_1G_TIMEOUT_EN; - - hw_dbg(hw, "Configuring Autoneg; PCS_LCTL = 0x%08X\n", reg); - IXGBE_WRITE_REG(hw, IXGBE_PCS1GLCTL, reg); - - /* See if autonegotiation has succeeded */ - hw->mac.autoneg_succeeded = 0; - for (i = 0; i < FIBER_LINK_UP_LIMIT; i++) { - msleep(10); - reg = IXGBE_READ_REG(hw, IXGBE_PCS1GLSTA); - if ((reg & (IXGBE_PCS1GLSTA_LINK_OK | - IXGBE_PCS1GLSTA_AN_COMPLETE)) == - (IXGBE_PCS1GLSTA_LINK_OK | - IXGBE_PCS1GLSTA_AN_COMPLETE)) { - if (!(reg & IXGBE_PCS1GLSTA_AN_TIMED_OUT)) - hw->mac.autoneg_succeeded = 1; - break; - } - } - - if (!hw->mac.autoneg_succeeded) { - /* Autoneg failed to achieve a link, so we turn fc off */ - hw->fc.current_mode = ixgbe_fc_none; - hw_dbg(hw, "Flow Control = NONE.\n"); - goto out; - } - - /* - * Read the AN advertisement and LP ability registers and resolve - * local flow control settings accordingly - */ - pcs_anadv_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA); - pcs_lpab_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANLP); - if ((pcs_anadv_reg & IXGBE_PCS1GANA_SYM_PAUSE) && - (pcs_lpab_reg & IXGBE_PCS1GANA_SYM_PAUSE)) { - /* - * Now we need to check if the user selected Rx ONLY - * of pause frames. In this case, we had to advertise - * FULL flow control because we could not advertise RX - * ONLY. Hence, we must now check to see if we need to - * turn OFF the TRANSMISSION of PAUSE frames. - */ - if (hw->fc.requested_mode == ixgbe_fc_full) { - hw->fc.current_mode = ixgbe_fc_full; - hw_dbg(hw, "Flow Control = FULL.\n"); - } else { - hw->fc.current_mode = ixgbe_fc_rx_pause; - hw_dbg(hw, "Flow Control = RX PAUSE frames only.\n"); - } - } else if (!(pcs_anadv_reg & IXGBE_PCS1GANA_SYM_PAUSE) && - (pcs_anadv_reg & IXGBE_PCS1GANA_ASM_PAUSE) && - (pcs_lpab_reg & IXGBE_PCS1GANA_SYM_PAUSE) && - (pcs_lpab_reg & IXGBE_PCS1GANA_ASM_PAUSE)) { - hw->fc.current_mode = ixgbe_fc_tx_pause; - hw_dbg(hw, "Flow Control = TX PAUSE frames only.\n"); - } else if ((pcs_anadv_reg & IXGBE_PCS1GANA_SYM_PAUSE) && - (pcs_anadv_reg & IXGBE_PCS1GANA_ASM_PAUSE) && - !(pcs_lpab_reg & IXGBE_PCS1GANA_SYM_PAUSE) && - (pcs_lpab_reg & IXGBE_PCS1GANA_ASM_PAUSE)) { - hw->fc.current_mode = ixgbe_fc_rx_pause; - hw_dbg(hw, "Flow Control = RX PAUSE frames only.\n"); - } else { - hw->fc.current_mode = ixgbe_fc_none; - hw_dbg(hw, "Flow Control = NONE.\n"); - } - -out: - return ret_val; -} - -/** - * ixgbe_setup_fc_generic - Set up flow control - * @hw: pointer to hardware structure - * - * Sets up flow control. - **/ -s32 ixgbe_setup_fc_generic(struct ixgbe_hw *hw, s32 packetbuf_num) -{ - s32 ret_val = 0; - ixgbe_link_speed speed; - bool link_up; - -#ifdef CONFIG_DCB - if (hw->fc.requested_mode == ixgbe_fc_pfc) { - hw->fc.current_mode = hw->fc.requested_mode; - goto out; - } - -#endif - /* Validate the packetbuf configuration */ - if (packetbuf_num < 0 || packetbuf_num > 7) { - hw_dbg(hw, "Invalid packet buffer number [%d], expected range " - "is 0-7\n", packetbuf_num); - ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS; - goto out; - } - - /* - * Validate the water mark configuration. Zero water marks are invalid - * because it causes the controller to just blast out fc packets. - */ - if (!hw->fc.low_water || !hw->fc.high_water || !hw->fc.pause_time) { - hw_dbg(hw, "Invalid water mark configuration\n"); - ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS; - goto out; - } - - /* - * Validate the requested mode. Strict IEEE mode does not allow - * ixgbe_fc_rx_pause because it will cause testing anomalies. - */ - if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) { - hw_dbg(hw, "ixgbe_fc_rx_pause not valid in strict " - "IEEE mode\n"); - ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS; - goto out; - } - - /* - * 10gig parts do not have a word in the EEPROM to determine the - * default flow control setting, so we explicitly set it to full. - */ - if (hw->fc.requested_mode == ixgbe_fc_default) - hw->fc.requested_mode = ixgbe_fc_full; - - /* - * Save off the requested flow control mode for use later. Depending - * on the link partner's capabilities, we may or may not use this mode. - */ - hw->fc.current_mode = hw->fc.requested_mode; - - /* Decide whether to use autoneg or not. */ - hw->mac.ops.check_link(hw, &speed, &link_up, false); - if (!hw->fc.disable_fc_autoneg && hw->phy.multispeed_fiber && - (speed == IXGBE_LINK_SPEED_1GB_FULL)) - ret_val = ixgbe_fc_autoneg(hw); - - if (ret_val) - goto out; - - ret_val = ixgbe_fc_enable(hw, packetbuf_num); - -out: - return ret_val; -} - -/** - * ixgbe_disable_pcie_master - Disable PCI-express master access - * @hw: pointer to hardware structure - * - * Disables PCI-Express master access and verifies there are no pending - * requests. IXGBE_ERR_MASTER_REQUESTS_PENDING is returned if master disable - * bit hasn't caused the master requests to be disabled, else 0 - * is returned signifying master requests disabled. - **/ -s32 ixgbe_disable_pcie_master(struct ixgbe_hw *hw) -{ - u32 i; - u32 reg_val; - u32 number_of_queues; - s32 status = IXGBE_ERR_MASTER_REQUESTS_PENDING; - - /* Disable the receive unit by stopping each queue */ - number_of_queues = hw->mac.max_rx_queues; - for (i = 0; i < number_of_queues; i++) { - reg_val = IXGBE_READ_REG(hw, IXGBE_RXDCTL(i)); - if (reg_val & IXGBE_RXDCTL_ENABLE) { - reg_val &= ~IXGBE_RXDCTL_ENABLE; - IXGBE_WRITE_REG(hw, IXGBE_RXDCTL(i), reg_val); - } - } - - reg_val = IXGBE_READ_REG(hw, IXGBE_CTRL); - reg_val |= IXGBE_CTRL_GIO_DIS; - IXGBE_WRITE_REG(hw, IXGBE_CTRL, reg_val); - - for (i = 0; i < IXGBE_PCI_MASTER_DISABLE_TIMEOUT; i++) { - if (!(IXGBE_READ_REG(hw, IXGBE_STATUS) & IXGBE_STATUS_GIO)) { - status = 0; - break; - } - udelay(100); - } - - return status; -} - - -/** - * ixgbe_acquire_swfw_sync - Acquire SWFW semaphore - * @hw: pointer to hardware structure - * @mask: Mask to specify which semaphore to acquire - * - * Acquires the SWFW semaphore thought the GSSR register for the specified - * function (CSR, PHY0, PHY1, EEPROM, Flash) - **/ -s32 ixgbe_acquire_swfw_sync(struct ixgbe_hw *hw, u16 mask) -{ - u32 gssr; - u32 swmask = mask; - u32 fwmask = mask << 5; - s32 timeout = 200; - - while (timeout) { - if (ixgbe_get_eeprom_semaphore(hw)) - return -IXGBE_ERR_SWFW_SYNC; - - gssr = IXGBE_READ_REG(hw, IXGBE_GSSR); - if (!(gssr & (fwmask | swmask))) - break; - - /* - * Firmware currently using resource (fwmask) or other software - * thread currently using resource (swmask) - */ - ixgbe_release_eeprom_semaphore(hw); - msleep(5); - timeout--; - } - - if (!timeout) { - hw_dbg(hw, "Driver can't access resource, GSSR timeout.\n"); - return -IXGBE_ERR_SWFW_SYNC; - } - - gssr |= swmask; - IXGBE_WRITE_REG(hw, IXGBE_GSSR, gssr); - - ixgbe_release_eeprom_semaphore(hw); - return 0; -} - -/** - * ixgbe_release_swfw_sync - Release SWFW semaphore - * @hw: pointer to hardware structure - * @mask: Mask to specify which semaphore to release - * - * Releases the SWFW semaphore thought the GSSR register for the specified - * function (CSR, PHY0, PHY1, EEPROM, Flash) - **/ -void ixgbe_release_swfw_sync(struct ixgbe_hw *hw, u16 mask) -{ - u32 gssr; - u32 swmask = mask; - - ixgbe_get_eeprom_semaphore(hw); - - gssr = IXGBE_READ_REG(hw, IXGBE_GSSR); - gssr &= ~swmask; - IXGBE_WRITE_REG(hw, IXGBE_GSSR, gssr); - - ixgbe_release_eeprom_semaphore(hw); -} - -/** - * ixgbe_enable_rx_dma_generic - Enable the Rx DMA unit - * @hw: pointer to hardware structure - * @regval: register value to write to RXCTRL - * - * Enables the Rx DMA unit - **/ -s32 ixgbe_enable_rx_dma_generic(struct ixgbe_hw *hw, u32 regval) -{ - IXGBE_WRITE_REG(hw, IXGBE_RXCTRL, regval); - - return 0; -} - -/** - * ixgbe_blink_led_start_generic - Blink LED based on index. - * @hw: pointer to hardware structure - * @index: led number to blink - **/ -s32 ixgbe_blink_led_start_generic(struct ixgbe_hw *hw, u32 index) -{ - ixgbe_link_speed speed = 0; - bool link_up = 0; - u32 autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC); - u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL); - - /* - * Link must be up to auto-blink the LEDs; - * Force it if link is down. - */ - hw->mac.ops.check_link(hw, &speed, &link_up, false); - - if (!link_up) { - autoc_reg |= IXGBE_AUTOC_FLU; - IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc_reg); - msleep(10); - } - - led_reg &= ~IXGBE_LED_MODE_MASK(index); - led_reg |= IXGBE_LED_BLINK(index); - IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg); - IXGBE_WRITE_FLUSH(hw); - - return 0; -} - -/** - * ixgbe_blink_led_stop_generic - Stop blinking LED based on index. - * @hw: pointer to hardware structure - * @index: led number to stop blinking - **/ -s32 ixgbe_blink_led_stop_generic(struct ixgbe_hw *hw, u32 index) -{ - u32 autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC); - u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL); - - autoc_reg &= ~IXGBE_AUTOC_FLU; - autoc_reg |= IXGBE_AUTOC_AN_RESTART; - IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc_reg); - - led_reg &= ~IXGBE_LED_MODE_MASK(index); - led_reg &= ~IXGBE_LED_BLINK(index); - led_reg |= IXGBE_LED_LINK_ACTIVE << IXGBE_LED_MODE_SHIFT(index); - IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg); - IXGBE_WRITE_FLUSH(hw); - - return 0; -} |