1 files changed, 90 insertions, 0 deletions
diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig
new file mode 100644
index 00000000000..2d09c116cbc
--- /dev/null
+++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig
@@ -0,0 +1,90 @@
+config STMMAC_ETH
+	tristate "STMicroelectronics 10/100/1000 Ethernet driver"
+	depends on HAS_IOMEM && HAS_DMA
+	select MII
+	select PHYLIB
+	select CRC32
+	select PTP_1588_CLOCK
+	select RESET_CONTROLLER
+	---help---
+	  This is the driver for the Ethernet IPs are built around a
+	  Synopsys IP Core and only tested on the STMicroelectronics
+	  platforms.
+
+if STMMAC_ETH
+
+config STMMAC_PLATFORM
+	bool "STMMAC Platform bus support"
+	depends on STMMAC_ETH
+	default y
+	---help---
+	  This selects the platform specific bus support for
+	  the stmmac device driver. This is the driver used
+	  on many embedded STM platforms based on ARM and SuperH
+	  processors.
+	  If you have a controller with this interface, say Y or M here.
+
+	  If unsure, say N.
+
+config DWMAC_SOCFPGA
+	bool "SOCFPGA dwmac support"
+	depends on STMMAC_PLATFORM && MFD_SYSCON && (ARCH_SOCFPGA || COMPILE_TEST)
+	help
+	  Support for ethernet controller on Altera SOCFPGA
+
+	  This selects the Altera SOCFPGA SoC glue layer support
+	  for the stmmac device driver. This driver is used for
+	  arria5 and cyclone5 FPGA SoCs.
+
+config DWMAC_SUNXI
+	bool "Allwinner GMAC support"
+	depends on STMMAC_PLATFORM && ARCH_SUNXI
+	default y
+	---help---
+	  Support for Allwinner A20/A31 GMAC ethernet controllers.
+
+	  This selects Allwinner SoC glue layer support for the
+	  stmmac device driver. This driver is used for A20/A31
+	  GMAC 	  ethernet controller.
+
+config DWMAC_STI
+	bool "STi GMAC support"
+	depends on STMMAC_PLATFORM && ARCH_STI
+	default y
+	---help---
+	  Support for ethernet controller on STi SOCs.
+
+	  This selects STi SoC glue layer support for the stmmac
+	  device driver. This driver is used on for the STi series
+	  SOCs GMAC ethernet controller.
+
+config STMMAC_PCI
+	bool "STMMAC PCI bus support"
+	depends on STMMAC_ETH && PCI
+	---help---
+	  This is to select the Synopsys DWMAC available on PCI devices,
+	  if you have a controller with this interface, say Y or M here.
+
+	  This PCI support is tested on XLINX XC2V3000 FF1152AMT0221
+	  D1215994A VIRTEX FPGA board.
+
+	  If unsure, say N.
+
+config STMMAC_DEBUG_FS
+	bool "Enable monitoring via sysFS "
+	default n
+	depends on STMMAC_ETH && DEBUG_FS
+	---help---
+	  The stmmac entry in /sys reports DMA TX/RX rings
+	  or (if supported) the HW cap register.
+
+config STMMAC_DA
+	bool "STMMAC DMA arbitration scheme"
+	default n
+	---help---
+	  Selecting this option, rx has priority over Tx (only for Giga
+	  Ethernet device).
+	  By default, the DMA arbitration scheme is based on Round-robin
+	  (rx:tx priority is 1:1).
+
+endif