diff options
Diffstat (limited to 'drivers/net/ethernet/8390')
| -rw-r--r-- | drivers/net/ethernet/8390/8390.h | 47 | ||||
| -rw-r--r-- | drivers/net/ethernet/8390/Kconfig | 7 | ||||
| -rw-r--r-- | drivers/net/ethernet/8390/Makefile | 1 | ||||
| -rw-r--r-- | drivers/net/ethernet/8390/apne.c | 65 | ||||
| -rw-r--r-- | drivers/net/ethernet/8390/ax88796.c | 35 | ||||
| -rw-r--r-- | drivers/net/ethernet/8390/axnet_cs.c | 120 | ||||
| -rw-r--r-- | drivers/net/ethernet/8390/etherh.c | 53 | ||||
| -rw-r--r-- | drivers/net/ethernet/8390/hydra.c | 13 | ||||
| -rw-r--r-- | drivers/net/ethernet/8390/lib8390.c | 79 | ||||
| -rw-r--r-- | drivers/net/ethernet/8390/mac8390.c | 19 | ||||
| -rw-r--r-- | drivers/net/ethernet/8390/mcf8390.c | 9 | ||||
| -rw-r--r-- | drivers/net/ethernet/8390/ne-h8300.c | 684 | ||||
| -rw-r--r-- | drivers/net/ethernet/8390/ne.c | 96 | ||||
| -rw-r--r-- | drivers/net/ethernet/8390/ne2k-pci.c | 57 | ||||
| -rw-r--r-- | drivers/net/ethernet/8390/pcnet_cs.c | 63 | ||||
| -rw-r--r-- | drivers/net/ethernet/8390/smc-ultra.c | 48 | ||||
| -rw-r--r-- | drivers/net/ethernet/8390/stnic.c | 28 | ||||
| -rw-r--r-- | drivers/net/ethernet/8390/wd.c | 42 | ||||
| -rw-r--r-- | drivers/net/ethernet/8390/zorro8390.c | 26 |
19 files changed, 457 insertions, 1035 deletions
diff --git a/drivers/net/ethernet/8390/8390.h b/drivers/net/ethernet/8390/8390.h index ef325ffa1b5..3e2f2c2e7b5 100644 --- a/drivers/net/ethernet/8390/8390.h +++ b/drivers/net/ethernet/8390/8390.h @@ -21,49 +21,43 @@ struct e8390_pkt_hdr { unsigned short count; /* header + packet length in bytes */ }; -#ifdef notdef -extern int ei_debug; -#else -#define ei_debug 1 -#endif - #ifdef CONFIG_NET_POLL_CONTROLLER -extern void ei_poll(struct net_device *dev); -extern void eip_poll(struct net_device *dev); +void ei_poll(struct net_device *dev); +void eip_poll(struct net_device *dev); #endif /* Without I/O delay - non ISA or later chips */ -extern void NS8390_init(struct net_device *dev, int startp); -extern int ei_open(struct net_device *dev); -extern int ei_close(struct net_device *dev); -extern irqreturn_t ei_interrupt(int irq, void *dev_id); -extern void ei_tx_timeout(struct net_device *dev); -extern netdev_tx_t ei_start_xmit(struct sk_buff *skb, struct net_device *dev); -extern void ei_set_multicast_list(struct net_device *dev); -extern struct net_device_stats *ei_get_stats(struct net_device *dev); +void NS8390_init(struct net_device *dev, int startp); +int ei_open(struct net_device *dev); +int ei_close(struct net_device *dev); +irqreturn_t ei_interrupt(int irq, void *dev_id); +void ei_tx_timeout(struct net_device *dev); +netdev_tx_t ei_start_xmit(struct sk_buff *skb, struct net_device *dev); +void ei_set_multicast_list(struct net_device *dev); +struct net_device_stats *ei_get_stats(struct net_device *dev); extern const struct net_device_ops ei_netdev_ops; -extern struct net_device *__alloc_ei_netdev(int size); +struct net_device *__alloc_ei_netdev(int size); static inline struct net_device *alloc_ei_netdev(void) { return __alloc_ei_netdev(0); } /* With I/O delay form */ -extern void NS8390p_init(struct net_device *dev, int startp); -extern int eip_open(struct net_device *dev); -extern int eip_close(struct net_device *dev); -extern irqreturn_t eip_interrupt(int irq, void *dev_id); -extern void eip_tx_timeout(struct net_device *dev); -extern netdev_tx_t eip_start_xmit(struct sk_buff *skb, struct net_device *dev); -extern void eip_set_multicast_list(struct net_device *dev); -extern struct net_device_stats *eip_get_stats(struct net_device *dev); +void NS8390p_init(struct net_device *dev, int startp); +int eip_open(struct net_device *dev); +int eip_close(struct net_device *dev); +irqreturn_t eip_interrupt(int irq, void *dev_id); +void eip_tx_timeout(struct net_device *dev); +netdev_tx_t eip_start_xmit(struct sk_buff *skb, struct net_device *dev); +void eip_set_multicast_list(struct net_device *dev); +struct net_device_stats *eip_get_stats(struct net_device *dev); extern const struct net_device_ops eip_netdev_ops; -extern struct net_device *__alloc_eip_netdev(int size); +struct net_device *__alloc_eip_netdev(int size); static inline struct net_device *alloc_eip_netdev(void) { return __alloc_eip_netdev(0); @@ -99,6 +93,7 @@ struct ei_device { u32 *reg_offset; /* Register mapping table */ spinlock_t page_lock; /* Page register locks */ unsigned long priv; /* Private field to store bus IDs etc. */ + u32 msg_enable; /* debug message level */ #ifdef AX88796_PLATFORM unsigned char rxcr_base; /* default value for RXCR */ #endif diff --git a/drivers/net/ethernet/8390/Kconfig b/drivers/net/ethernet/8390/Kconfig index a5f91e1e8fe..0988811f4e4 100644 --- a/drivers/net/ethernet/8390/Kconfig +++ b/drivers/net/ethernet/8390/Kconfig @@ -146,13 +146,6 @@ config PCMCIA_PCNET To compile this driver as a module, choose M here: the module will be called pcnet_cs. If unsure, say N. -config NE_H8300 - tristate "NE2000 compatible support for H8/300" - depends on H8300 - ---help--- - Say Y here if you want to use the NE2000 compatible - controller on the Renesas H8/300 processor. - config STNIC tristate "National DP83902AV support" depends on SUPERH diff --git a/drivers/net/ethernet/8390/Makefile b/drivers/net/ethernet/8390/Makefile index 588954a79b2..ff3b3189418 100644 --- a/drivers/net/ethernet/8390/Makefile +++ b/drivers/net/ethernet/8390/Makefile @@ -10,7 +10,6 @@ obj-$(CONFIG_HYDRA) += hydra.o 8390.o obj-$(CONFIG_MCF8390) += mcf8390.o 8390.o obj-$(CONFIG_NE2000) += ne.o 8390p.o obj-$(CONFIG_NE2K_PCI) += ne2k-pci.o 8390.o -obj-$(CONFIG_NE_H8300) += ne-h8300.o 8390.o obj-$(CONFIG_PCMCIA_AXNET) += axnet_cs.o 8390.o obj-$(CONFIG_PCMCIA_PCNET) += pcnet_cs.o 8390.o obj-$(CONFIG_STNIC) += stnic.o 8390.o diff --git a/drivers/net/ethernet/8390/apne.c b/drivers/net/ethernet/8390/apne.c index 912ed7a5f33..c56ac9ebc08 100644 --- a/drivers/net/ethernet/8390/apne.c +++ b/drivers/net/ethernet/8390/apne.c @@ -116,9 +116,15 @@ static const char version[] = static int apne_owned; /* signal if card already owned */ +static u32 apne_msg_enable; +module_param_named(msg_enable, apne_msg_enable, uint, (S_IRUSR|S_IRGRP|S_IROTH)); +MODULE_PARM_DESC(msg_enable, "Debug message level (see linux/netdevice.h for bitmap)"); + struct net_device * __init apne_probe(int unit) { struct net_device *dev; + struct ei_device *ei_local; + #ifndef MANUAL_CONFIG char tuple[8]; #endif @@ -133,11 +139,11 @@ struct net_device * __init apne_probe(int unit) if ( !(AMIGAHW_PRESENT(PCMCIA)) ) return ERR_PTR(-ENODEV); - printk("Looking for PCMCIA ethernet card : "); + pr_info("Looking for PCMCIA ethernet card : "); /* check if a card is inserted */ if (!(PCMCIA_INSERTED)) { - printk("NO PCMCIA card inserted\n"); + pr_cont("NO PCMCIA card inserted\n"); return ERR_PTR(-ENODEV); } @@ -148,6 +154,8 @@ struct net_device * __init apne_probe(int unit) sprintf(dev->name, "eth%d", unit); netdev_boot_setup_check(dev); } + ei_local = netdev_priv(dev); + ei_local->msg_enable = apne_msg_enable; /* disable pcmcia irq for readtuple */ pcmcia_disable_irq(); @@ -155,14 +163,14 @@ struct net_device * __init apne_probe(int unit) #ifndef MANUAL_CONFIG if ((pcmcia_copy_tuple(CISTPL_FUNCID, tuple, 8) < 3) || (tuple[2] != CISTPL_FUNCID_NETWORK)) { - printk("not an ethernet card\n"); + pr_cont("not an ethernet card\n"); /* XXX: shouldn't we re-enable irq here? */ free_netdev(dev); return ERR_PTR(-ENODEV); } #endif - printk("ethernet PCMCIA card inserted\n"); + pr_cont("ethernet PCMCIA card inserted\n"); if (!init_pcmcia()) { /* XXX: shouldn't we re-enable irq here? */ @@ -205,10 +213,10 @@ static int __init apne_probe1(struct net_device *dev, int ioaddr) #endif static unsigned version_printed; - if (ei_debug && version_printed++ == 0) - printk(version); + if ((apne_msg_enable & NETIF_MSG_DRV) && (version_printed++ == 0)) + netdev_info(dev, version); - printk("PCMCIA NE*000 ethercard probe"); + netdev_info(dev, "PCMCIA NE*000 ethercard probe"); /* Reset card. Who knows what dain-bramaged state it was left in. */ { unsigned long reset_start_time = jiffies; @@ -217,7 +225,7 @@ static int __init apne_probe1(struct net_device *dev, int ioaddr) while ((inb(ioaddr + NE_EN0_ISR) & ENISR_RESET) == 0) if (time_after(jiffies, reset_start_time + 2*HZ/100)) { - printk(" not found (no reset ack).\n"); + pr_cont(" not found (no reset ack).\n"); return -ENODEV; } @@ -288,7 +296,7 @@ static int __init apne_probe1(struct net_device *dev, int ioaddr) start_page = 0x01; stop_page = (wordlength == 2) ? 0x40 : 0x20; } else { - printk(" not found.\n"); + pr_cont(" not found.\n"); return -ENXIO; } @@ -320,9 +328,9 @@ static int __init apne_probe1(struct net_device *dev, int ioaddr) for (i = 0; i < ETH_ALEN; i++) dev->dev_addr[i] = SA_prom[i]; - printk(" %pM\n", dev->dev_addr); + pr_cont(" %pM\n", dev->dev_addr); - printk("%s: %s found.\n", dev->name, name); + netdev_info(dev, "%s found.\n", name); ei_status.name = name; ei_status.tx_start_page = start_page; @@ -352,10 +360,11 @@ static void apne_reset_8390(struct net_device *dev) { unsigned long reset_start_time = jiffies; + struct ei_device *ei_local = netdev_priv(dev); init_pcmcia(); - if (ei_debug > 1) printk("resetting the 8390 t=%ld...", jiffies); + netif_dbg(ei_local, hw, dev, "resetting the 8390 t=%ld...\n", jiffies); outb(inb(NE_BASE + NE_RESET), NE_BASE + NE_RESET); @@ -365,8 +374,8 @@ apne_reset_8390(struct net_device *dev) /* This check _should_not_ be necessary, omit eventually. */ while ((inb(NE_BASE+NE_EN0_ISR) & ENISR_RESET) == 0) if (time_after(jiffies, reset_start_time + 2*HZ/100)) { - printk("%s: ne_reset_8390() did not complete.\n", dev->name); - break; + netdev_err(dev, "ne_reset_8390() did not complete.\n"); + break; } outb(ENISR_RESET, NE_BASE + NE_EN0_ISR); /* Ack intr. */ } @@ -386,9 +395,9 @@ apne_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr, int ring_pa /* This *shouldn't* happen. If it does, it's the last thing you'll see */ if (ei_status.dmaing) { - printk("%s: DMAing conflict in ne_get_8390_hdr " - "[DMAstat:%d][irqlock:%d][intr:%d].\n", - dev->name, ei_status.dmaing, ei_status.irqlock, dev->irq); + netdev_err(dev, "DMAing conflict in ne_get_8390_hdr " + "[DMAstat:%d][irqlock:%d][intr:%d].\n", + ei_status.dmaing, ei_status.irqlock, dev->irq); return; } @@ -433,9 +442,9 @@ apne_block_input(struct net_device *dev, int count, struct sk_buff *skb, int rin /* This *shouldn't* happen. If it does, it's the last thing you'll see */ if (ei_status.dmaing) { - printk("%s: DMAing conflict in ne_block_input " - "[DMAstat:%d][irqlock:%d][intr:%d].\n", - dev->name, ei_status.dmaing, ei_status.irqlock, dev->irq); + netdev_err(dev, "DMAing conflict in ne_block_input " + "[DMAstat:%d][irqlock:%d][intr:%d].\n", + ei_status.dmaing, ei_status.irqlock, dev->irq); return; } ei_status.dmaing |= 0x01; @@ -481,9 +490,9 @@ apne_block_output(struct net_device *dev, int count, /* This *shouldn't* happen. If it does, it's the last thing you'll see */ if (ei_status.dmaing) { - printk("%s: DMAing conflict in ne_block_output." - "[DMAstat:%d][irqlock:%d][intr:%d]\n", - dev->name, ei_status.dmaing, ei_status.irqlock, dev->irq); + netdev_err(dev, "DMAing conflict in ne_block_output." + "[DMAstat:%d][irqlock:%d][intr:%d]\n", + ei_status.dmaing, ei_status.irqlock, dev->irq); return; } ei_status.dmaing |= 0x01; @@ -513,7 +522,7 @@ apne_block_output(struct net_device *dev, int count, while ((inb(NE_BASE + NE_EN0_ISR) & ENISR_RDC) == 0) if (time_after(jiffies, dma_start + 2*HZ/100)) { /* 20ms */ - printk("%s: timeout waiting for Tx RDC.\n", dev->name); + netdev_warn(dev, "timeout waiting for Tx RDC.\n"); apne_reset_8390(dev); NS8390_init(dev,1); break; @@ -536,8 +545,8 @@ static irqreturn_t apne_interrupt(int irq, void *dev_id) pcmcia_ack_int(pcmcia_intreq); return IRQ_NONE; } - if (ei_debug > 3) - printk("pcmcia intreq = %x\n", pcmcia_intreq); + if (apne_msg_enable & NETIF_MSG_INTR) + pr_debug("pcmcia intreq = %x\n", pcmcia_intreq); pcmcia_disable_irq(); /* to get rid of the sti() within ei_interrupt */ ei_interrupt(irq, dev_id); pcmcia_ack_int(pcmcia_get_intreq()); @@ -551,9 +560,7 @@ static struct net_device *apne_dev; static int __init apne_module_init(void) { apne_dev = apne_probe(-1); - if (IS_ERR(apne_dev)) - return PTR_ERR(apne_dev); - return 0; + return PTR_ERR_OR_ZERO(apne_dev); } static void __exit apne_module_exit(void) diff --git a/drivers/net/ethernet/8390/ax88796.c b/drivers/net/ethernet/8390/ax88796.c index e1d26433d61..1d162ccb473 100644 --- a/drivers/net/ethernet/8390/ax88796.c +++ b/drivers/net/ethernet/8390/ax88796.c @@ -15,7 +15,6 @@ #include <linux/kernel.h> #include <linux/errno.h> #include <linux/isapnp.h> -#include <linux/init.h> #include <linux/interrupt.h> #include <linux/io.h> #include <linux/platform_device.h> @@ -78,6 +77,8 @@ static unsigned char version[] = "ax88796.c: Copyright 2005,2007 Simtec Electron #define AX_GPOC_PPDSET BIT(6) +static u32 ax_msg_enable; + /* device private data */ struct ax_device { @@ -147,8 +148,7 @@ static void ax_reset_8390(struct net_device *dev) unsigned long reset_start_time = jiffies; void __iomem *addr = (void __iomem *)dev->base_addr; - if (ei_debug > 1) - netdev_dbg(dev, "resetting the 8390 t=%ld\n", jiffies); + netif_dbg(ei_local, hw, dev, "resetting the 8390 t=%ld...\n", jiffies); ei_outb(ei_inb(addr + NE_RESET), addr + NE_RESET); @@ -157,7 +157,7 @@ static void ax_reset_8390(struct net_device *dev) /* This check _should_not_ be necessary, omit eventually. */ while ((ei_inb(addr + EN0_ISR) & ENISR_RESET) == 0) { - if (jiffies - reset_start_time > 2 * HZ / 100) { + if (time_after(jiffies, reset_start_time + 2 * HZ / 100)) { netdev_warn(dev, "%s: did not complete.\n", __func__); break; } @@ -293,7 +293,7 @@ static void ax_block_output(struct net_device *dev, int count, dma_start = jiffies; while ((ei_inb(nic_base + EN0_ISR) & ENISR_RDC) == 0) { - if (jiffies - dma_start > 2 * HZ / 100) { /* 20ms */ + if (time_after(jiffies, dma_start + 2 * HZ / 100)) { /* 20ms */ netdev_warn(dev, "timeout waiting for Tx RDC.\n"); ax_reset_8390(dev); ax_NS8390_init(dev, 1); @@ -496,12 +496,28 @@ static int ax_set_settings(struct net_device *dev, struct ethtool_cmd *cmd) return phy_ethtool_sset(phy_dev, cmd); } +static u32 ax_get_msglevel(struct net_device *dev) +{ + struct ei_device *ei_local = netdev_priv(dev); + + return ei_local->msg_enable; +} + +static void ax_set_msglevel(struct net_device *dev, u32 v) +{ + struct ei_device *ei_local = netdev_priv(dev); + + ei_local->msg_enable = v; +} + static const struct ethtool_ops ax_ethtool_ops = { .get_drvinfo = ax_get_drvinfo, .get_settings = ax_get_settings, .set_settings = ax_set_settings, .get_link = ethtool_op_get_link, .get_ts_info = ethtool_op_get_ts_info, + .get_msglevel = ax_get_msglevel, + .set_msglevel = ax_set_msglevel, }; #ifdef CONFIG_AX88796_93CX6 @@ -702,12 +718,12 @@ static int ax_init_dev(struct net_device *dev) for (i = 0; i < 16; i++) SA_prom[i] = SA_prom[i+i]; - memcpy(dev->dev_addr, SA_prom, 6); + memcpy(dev->dev_addr, SA_prom, ETH_ALEN); } #ifdef CONFIG_AX88796_93CX6 if (ax->plat->flags & AXFLG_HAS_93CX6) { - unsigned char mac_addr[6]; + unsigned char mac_addr[ETH_ALEN]; struct eeprom_93cx6 eeprom; eeprom.data = ei_local; @@ -719,7 +735,7 @@ static int ax_init_dev(struct net_device *dev) (__le16 __force *)mac_addr, sizeof(mac_addr) >> 1); - memcpy(dev->dev_addr, mac_addr, 6); + memcpy(dev->dev_addr, mac_addr, ETH_ALEN); } #endif if (ax->plat->wordlength == 2) { @@ -763,6 +779,7 @@ static int ax_init_dev(struct net_device *dev) ei_local->block_output = &ax_block_output; ei_local->get_8390_hdr = &ax_get_8390_hdr; ei_local->priv = 0; + ei_local->msg_enable = ax_msg_enable; dev->netdev_ops = &ax_netdev_ops; dev->ethtool_ops = &ax_ethtool_ops; @@ -840,7 +857,7 @@ static int ax_probe(struct platform_device *pdev) ei_local = netdev_priv(dev); ax = to_ax_dev(dev); - ax->plat = pdev->dev.platform_data; + ax->plat = dev_get_platdata(&pdev->dev); platform_set_drvdata(pdev, dev); ei_local->rxcr_base = ax->plat->rcr_val; diff --git a/drivers/net/ethernet/8390/axnet_cs.c b/drivers/net/ethernet/8390/axnet_cs.c index d801c1410fb..73c57a4a7b9 100644 --- a/drivers/net/ethernet/8390/axnet_cs.c +++ b/drivers/net/ethernet/8390/axnet_cs.c @@ -28,7 +28,6 @@ #include <linux/kernel.h> #include <linux/module.h> -#include <linux/init.h> #include <linux/ptrace.h> #include <linux/string.h> #include <linux/timer.h> @@ -105,6 +104,7 @@ static void AX88190_init(struct net_device *dev, int startp); static int ax_open(struct net_device *dev); static int ax_close(struct net_device *dev); static irqreturn_t ax_interrupt(int irq, void *dev_id); +static u32 axnet_msg_enable; /*====================================================================*/ @@ -152,6 +152,7 @@ static int axnet_probe(struct pcmcia_device *link) return -ENOMEM; ei_local = netdev_priv(dev); + ei_local->msg_enable = axnet_msg_enable; spin_lock_init(&ei_local->page_lock); info = PRIV(dev); @@ -650,11 +651,12 @@ static void block_input(struct net_device *dev, int count, struct sk_buff *skb, int ring_offset) { unsigned int nic_base = dev->base_addr; + struct ei_device *ei_local = netdev_priv(dev); int xfer_count = count; char *buf = skb->data; - if ((ei_debug > 4) && (count != 4)) - pr_debug("%s: [bi=%d]\n", dev->name, count+4); + if ((netif_msg_rx_status(ei_local)) && (count != 4)) + netdev_dbg(dev, "[bi=%d]\n", count+4); outb_p(ring_offset & 0xff, nic_base + EN0_RSARLO); outb_p(ring_offset >> 8, nic_base + EN0_RSARHI); outb_p(E8390_RREAD+E8390_START, nic_base + AXNET_CMD); @@ -810,11 +812,6 @@ module_pcmcia_driver(axnet_cs_driver); #define ei_block_input (ei_local->block_input) #define ei_get_8390_hdr (ei_local->get_8390_hdr) -/* use 0 for production, 1 for verification, >2 for debug */ -#ifndef ei_debug -int ei_debug = 1; -#endif - /* Index to functions. */ static void ei_tx_intr(struct net_device *dev); static void ei_tx_err(struct net_device *dev); @@ -925,11 +922,10 @@ static void axnet_tx_timeout(struct net_device *dev) isr = inb(e8390_base+EN0_ISR); spin_unlock_irqrestore(&ei_local->page_lock, flags); - netdev_printk(KERN_DEBUG, dev, - "Tx timed out, %s TSR=%#2x, ISR=%#2x, t=%d.\n", - (txsr & ENTSR_ABT) ? "excess collisions." : - (isr) ? "lost interrupt?" : "cable problem?", - txsr, isr, tickssofar); + netdev_dbg(dev, "Tx timed out, %s TSR=%#2x, ISR=%#2x, t=%d.\n", + (txsr & ENTSR_ABT) ? "excess collisions." : + (isr) ? "lost interrupt?" : "cable problem?", + txsr, isr, tickssofar); if (!isr && !dev->stats.tx_packets) { @@ -998,29 +994,30 @@ static netdev_tx_t axnet_start_xmit(struct sk_buff *skb, { output_page = ei_local->tx_start_page; ei_local->tx1 = send_length; - if (ei_debug && ei_local->tx2 > 0) - netdev_printk(KERN_DEBUG, dev, - "idle transmitter tx2=%d, lasttx=%d, txing=%d\n", - ei_local->tx2, ei_local->lasttx, - ei_local->txing); + if ((netif_msg_tx_queued(ei_local)) && + ei_local->tx2 > 0) + netdev_dbg(dev, + "idle transmitter tx2=%d, lasttx=%d, txing=%d\n", + ei_local->tx2, ei_local->lasttx, + ei_local->txing); } else if (ei_local->tx2 == 0) { output_page = ei_local->tx_start_page + TX_PAGES/2; ei_local->tx2 = send_length; - if (ei_debug && ei_local->tx1 > 0) - netdev_printk(KERN_DEBUG, dev, - "idle transmitter, tx1=%d, lasttx=%d, txing=%d\n", - ei_local->tx1, ei_local->lasttx, - ei_local->txing); + if ((netif_msg_tx_queued(ei_local)) && + ei_local->tx1 > 0) + netdev_dbg(dev, + "idle transmitter, tx1=%d, lasttx=%d, txing=%d\n", + ei_local->tx1, ei_local->lasttx, + ei_local->txing); } else { /* We should never get here. */ - if (ei_debug) - netdev_printk(KERN_DEBUG, dev, - "No Tx buffers free! tx1=%d tx2=%d last=%d\n", - ei_local->tx1, ei_local->tx2, - ei_local->lasttx); + netif_dbg(ei_local, tx_err, dev, + "No Tx buffers free! tx1=%d tx2=%d last=%d\n", + ei_local->tx1, ei_local->tx2, + ei_local->lasttx); ei_local->irqlock = 0; netif_stop_queue(dev); outb_p(ENISR_ALL, e8390_base + EN0_IMR); @@ -1124,10 +1121,9 @@ static irqreturn_t ax_interrupt(int irq, void *dev_id) spin_unlock_irqrestore(&ei_local->page_lock, flags); return IRQ_NONE; } - - if (ei_debug > 3) - netdev_printk(KERN_DEBUG, dev, "interrupt(isr=%#2.2x)\n", - inb_p(e8390_base + EN0_ISR)); + + netif_dbg(ei_local, intr, dev, "interrupt(isr=%#2.2x)\n", + inb_p(e8390_base + EN0_ISR)); outb_p(0x00, e8390_base + EN0_ISR); ei_local->irqlock = 1; @@ -1137,9 +1133,8 @@ static irqreturn_t ax_interrupt(int irq, void *dev_id) ++nr_serviced < MAX_SERVICE) { if (!netif_running(dev) || (interrupts == 0xff)) { - if (ei_debug > 1) - netdev_warn(dev, - "interrupt from stopped card\n"); + netif_warn(ei_local, intr, dev, + "interrupt from stopped card\n"); outb_p(interrupts, e8390_base + EN0_ISR); interrupts = 0; break; @@ -1175,14 +1170,15 @@ static irqreturn_t ax_interrupt(int irq, void *dev_id) } } - if (interrupts && ei_debug > 3) + if (interrupts && (netif_msg_intr(ei_local))) { handled = 1; if (nr_serviced >= MAX_SERVICE) { /* 0xFF is valid for a card removal */ - if(interrupts!=0xFF) - netdev_warn(dev, "Too much work at interrupt, status %#2.2x\n", + if (interrupts != 0xFF) + netdev_warn(dev, + "Too much work at interrupt, status %#2.2x\n", interrupts); outb_p(ENISR_ALL, e8390_base + EN0_ISR); /* Ack. most intrs. */ } else { @@ -1221,8 +1217,7 @@ static void ei_tx_err(struct net_device *dev) unsigned char tx_was_aborted = txsr & (ENTSR_ABT+ENTSR_FU); #ifdef VERBOSE_ERROR_DUMP - netdev_printk(KERN_DEBUG, dev, - "transmitter error (%#2x):", txsr); + netdev_dbg(dev, "transmitter error (%#2x):", txsr); if (txsr & ENTSR_ABT) pr_cont(" excess-collisions"); if (txsr & ENTSR_ND) @@ -1287,9 +1282,9 @@ static void ei_tx_intr(struct net_device *dev) else if (ei_local->tx2 < 0) { if (ei_local->lasttx != 2 && ei_local->lasttx != -2) - netdev_info(dev, "%s: bogus last_tx_buffer %d, tx2=%d\n", - ei_local->name, ei_local->lasttx, - ei_local->tx2); + netdev_err(dev, "%s: bogus last_tx_buffer %d, tx2=%d\n", + ei_local->name, ei_local->lasttx, + ei_local->tx2); ei_local->tx2 = 0; if (ei_local->tx1 > 0) { @@ -1366,9 +1361,11 @@ static void ei_receive(struct net_device *dev) Keep quiet if it looks like a card removal. One problem here is that some clones crash in roughly the same way. */ - if (ei_debug > 0 && this_frame != ei_local->current_page && (this_frame!=0x0 || rxing_page!=0xFF)) - netdev_err(dev, "mismatched read page pointers %2x vs %2x\n", - this_frame, ei_local->current_page); + if ((netif_msg_rx_err(ei_local)) && + this_frame != ei_local->current_page && + (this_frame != 0x0 || rxing_page != 0xFF)) + netdev_err(dev, "mismatched read page pointers %2x vs %2x\n", + this_frame, ei_local->current_page); if (this_frame == rxing_page) /* Read all the frames? */ break; /* Done for now */ @@ -1383,11 +1380,10 @@ static void ei_receive(struct net_device *dev) if (pkt_len < 60 || pkt_len > 1518) { - if (ei_debug) - netdev_printk(KERN_DEBUG, dev, - "bogus packet size: %d, status=%#2x nxpg=%#2x\n", - rx_frame.count, rx_frame.status, - rx_frame.next); + netif_err(ei_local, rx_err, dev, + "bogus packet size: %d, status=%#2x nxpg=%#2x\n", + rx_frame.count, rx_frame.status, + rx_frame.next); dev->stats.rx_errors++; dev->stats.rx_length_errors++; } @@ -1398,10 +1394,9 @@ static void ei_receive(struct net_device *dev) skb = netdev_alloc_skb(dev, pkt_len + 2); if (skb == NULL) { - if (ei_debug > 1) - netdev_printk(KERN_DEBUG, dev, - "Couldn't allocate a sk_buff of size %d\n", - pkt_len); + netif_err(ei_local, rx_err, dev, + "Couldn't allocate a sk_buff of size %d\n", + pkt_len); dev->stats.rx_dropped++; break; } @@ -1420,11 +1415,10 @@ static void ei_receive(struct net_device *dev) } else { - if (ei_debug) - netdev_printk(KERN_DEBUG, dev, - "bogus packet: status=%#2x nxpg=%#2x size=%d\n", - rx_frame.status, rx_frame.next, - rx_frame.count); + netif_err(ei_local, rx_err, dev, + "bogus packet: status=%#2x nxpg=%#2x size=%d\n", + rx_frame.status, rx_frame.next, + rx_frame.count); dev->stats.rx_errors++; /* NB: The NIC counts CRC, frame and missed errors. */ if (pkt_stat & ENRSR_FO) @@ -1461,6 +1455,7 @@ static void ei_rx_overrun(struct net_device *dev) axnet_dev_t *info = PRIV(dev); long e8390_base = dev->base_addr; unsigned char was_txing, must_resend = 0; + struct ei_device *ei_local = netdev_priv(dev); /* * Record whether a Tx was in progress and then issue the @@ -1468,9 +1463,8 @@ static void ei_rx_overrun(struct net_device *dev) */ was_txing = inb_p(e8390_base+E8390_CMD) & E8390_TRANS; outb_p(E8390_NODMA+E8390_PAGE0+E8390_STOP, e8390_base+E8390_CMD); - - if (ei_debug > 1) - netdev_printk(KERN_DEBUG, dev, "Receiver overrun\n"); + + netif_dbg(ei_local, rx_err, dev, "Receiver overrun\n"); dev->stats.rx_over_errors++; /* diff --git a/drivers/net/ethernet/8390/etherh.c b/drivers/net/ethernet/8390/etherh.c index 78c6fb4b114..b36ee9e0d22 100644 --- a/drivers/net/ethernet/8390/etherh.c +++ b/drivers/net/ethernet/8390/etherh.c @@ -56,18 +56,15 @@ #define ei_inb_p(_p) readb((void __iomem *)_p) #define ei_outb_p(_v,_p) writeb(_v,(void __iomem *)_p) -#define NET_DEBUG 0 -#define DEBUG_INIT 2 - #define DRV_NAME "etherh" #define DRV_VERSION "1.11" -static char version[] __initdata = +static char version[] = "EtherH/EtherM Driver (c) 2002-2004 Russell King " DRV_VERSION "\n"; #include "lib8390.c" -static unsigned int net_debug = NET_DEBUG; +static u32 etherh_msg_enable; struct etherh_priv { void __iomem *ioc_fast; @@ -317,9 +314,9 @@ etherh_block_output (struct net_device *dev, int count, const unsigned char *buf void __iomem *dma_base, *addr; if (ei_local->dmaing) { - printk(KERN_ERR "%s: DMAing conflict in etherh_block_input: " - " DMAstat %d irqlock %d\n", dev->name, - ei_local->dmaing, ei_local->irqlock); + netdev_err(dev, "DMAing conflict in etherh_block_input: " + " DMAstat %d irqlock %d\n", + ei_local->dmaing, ei_local->irqlock); return; } @@ -361,8 +358,7 @@ etherh_block_output (struct net_device *dev, int count, const unsigned char *buf while ((readb (addr + EN0_ISR) & ENISR_RDC) == 0) if (time_after(jiffies, dma_start + 2*HZ/100)) { /* 20ms */ - printk(KERN_ERR "%s: timeout waiting for TX RDC\n", - dev->name); + netdev_warn(dev, "timeout waiting for TX RDC\n"); etherh_reset (dev); __NS8390_init (dev, 1); break; @@ -383,9 +379,9 @@ etherh_block_input (struct net_device *dev, int count, struct sk_buff *skb, int void __iomem *dma_base, *addr; if (ei_local->dmaing) { - printk(KERN_ERR "%s: DMAing conflict in etherh_block_input: " - " DMAstat %d irqlock %d\n", dev->name, - ei_local->dmaing, ei_local->irqlock); + netdev_err(dev, "DMAing conflict in etherh_block_input: " + " DMAstat %d irqlock %d\n", + ei_local->dmaing, ei_local->irqlock); return; } @@ -423,9 +419,9 @@ etherh_get_header (struct net_device *dev, struct e8390_pkt_hdr *hdr, int ring_p void __iomem *dma_base, *addr; if (ei_local->dmaing) { - printk(KERN_ERR "%s: DMAing conflict in etherh_get_header: " - " DMAstat %d irqlock %d\n", dev->name, - ei_local->dmaing, ei_local->irqlock); + netdev_err(dev, "DMAing conflict in etherh_get_header: " + " DMAstat %d irqlock %d\n", + ei_local->dmaing, ei_local->irqlock); return; } @@ -513,8 +509,8 @@ static void __init etherh_banner(void) { static int version_printed; - if (net_debug && version_printed++ == 0) - printk(KERN_INFO "%s", version); + if ((etherh_msg_enable & NETIF_MSG_DRV) && (version_printed++ == 0)) + pr_info("%s", version); } /* @@ -625,11 +621,27 @@ static int etherh_set_settings(struct net_device *dev, struct ethtool_cmd *cmd) return 0; } +static u32 etherh_get_msglevel(struct net_device *dev) +{ + struct ei_device *ei_local = netdev_priv(dev); + + return ei_local->msg_enable; +} + +static void etherh_set_msglevel(struct net_device *dev, u32 v) +{ + struct ei_device *ei_local = netdev_priv(dev); + + ei_local->msg_enable = v; +} + static const struct ethtool_ops etherh_ethtool_ops = { .get_settings = etherh_get_settings, .set_settings = etherh_set_settings, .get_drvinfo = etherh_get_drvinfo, .get_ts_info = ethtool_op_get_ts_info, + .get_msglevel = etherh_get_msglevel, + .set_msglevel = etherh_set_msglevel, }; static const struct net_device_ops etherh_netdev_ops = { @@ -746,6 +758,7 @@ etherh_probe(struct expansion_card *ec, const struct ecard_id *id) ei_local->block_output = etherh_block_output; ei_local->get_8390_hdr = etherh_get_header; ei_local->interface_num = 0; + ei_local->msg_enable = etherh_msg_enable; etherh_reset(dev); __NS8390_init(dev, 0); @@ -754,8 +767,8 @@ etherh_probe(struct expansion_card *ec, const struct ecard_id *id) if (ret) goto free; - printk(KERN_INFO "%s: %s in slot %d, %pM\n", - dev->name, data->name, ec->slot_no, dev->dev_addr); + netdev_info(dev, "%s in slot %d, %pM\n", + data->name, ec->slot_no, dev->dev_addr); ecard_set_drvdata(ec, dev); diff --git a/drivers/net/ethernet/8390/hydra.c b/drivers/net/ethernet/8390/hydra.c index fb3dd4399cf..0fe19d609c2 100644 --- a/drivers/net/ethernet/8390/hydra.c +++ b/drivers/net/ethernet/8390/hydra.c @@ -66,6 +66,7 @@ static void hydra_block_input(struct net_device *dev, int count, static void hydra_block_output(struct net_device *dev, int count, const unsigned char *buf, int start_page); static void hydra_remove_one(struct zorro_dev *z); +static u32 hydra_msg_enable; static struct zorro_device_id hydra_zorro_tbl[] = { { ZORRO_PROD_HYDRA_SYSTEMS_AMIGANET }, @@ -113,12 +114,13 @@ static const struct net_device_ops hydra_netdev_ops = { static int hydra_init(struct zorro_dev *z) { struct net_device *dev; - unsigned long board = ZTWO_VADDR(z->resource.start); + unsigned long board = (unsigned long)ZTWO_VADDR(z->resource.start); unsigned long ioaddr = board+HYDRA_NIC_BASE; const char name[] = "NE2000"; int start_page, stop_page; int j; int err; + struct ei_device *ei_local; static u32 hydra_offsets[16] = { 0x00, 0x02, 0x04, 0x06, 0x08, 0x0a, 0x0c, 0x0e, @@ -137,6 +139,8 @@ static int hydra_init(struct zorro_dev *z) start_page = NESM_START_PG; stop_page = NESM_STOP_PG; + ei_local = netdev_priv(dev); + ei_local->msg_enable = hydra_msg_enable; dev->base_addr = ioaddr; dev->irq = IRQ_AMIGA_PORTS; @@ -187,15 +191,16 @@ static int hydra_open(struct net_device *dev) static int hydra_close(struct net_device *dev) { - if (ei_debug > 1) - printk(KERN_DEBUG "%s: Shutting down ethercard.\n", dev->name); + struct ei_device *ei_local = netdev_priv(dev); + + netif_dbg(ei_local, ifdown, dev, "Shutting down ethercard.\n"); __ei_close(dev); return 0; } static void hydra_reset_8390(struct net_device *dev) { - printk(KERN_INFO "Hydra hw reset not there\n"); + netdev_info(dev, "Hydra hw reset not there\n"); } static void hydra_get_8390_hdr(struct net_device *dev, diff --git a/drivers/net/ethernet/8390/lib8390.c b/drivers/net/ethernet/8390/lib8390.c index b329f5c0d62..599311f0e05 100644 --- a/drivers/net/ethernet/8390/lib8390.c +++ b/drivers/net/ethernet/8390/lib8390.c @@ -99,11 +99,6 @@ #define ei_block_input (ei_local->block_input) #define ei_get_8390_hdr (ei_local->get_8390_hdr) -/* use 0 for production, 1 for verification, >2 for debug */ -#ifndef ei_debug -int ei_debug = 1; -#endif - /* Index to functions. */ static void ei_tx_intr(struct net_device *dev); static void ei_tx_err(struct net_device *dev); @@ -116,6 +111,11 @@ static void NS8390_trigger_send(struct net_device *dev, unsigned int length, static void do_set_multicast_list(struct net_device *dev); static void __NS8390_init(struct net_device *dev, int startp); +static unsigned version_printed; +static u32 msg_enable; +module_param(msg_enable, uint, (S_IRUSR|S_IRGRP|S_IROTH)); +MODULE_PARM_DESC(msg_enable, "Debug message level (see linux/netdevice.h for bitmap)"); + /* * SMP and the 8390 setup. * @@ -345,19 +345,23 @@ static netdev_tx_t __ei_start_xmit(struct sk_buff *skb, if (ei_local->tx1 == 0) { output_page = ei_local->tx_start_page; ei_local->tx1 = send_length; - if (ei_debug && ei_local->tx2 > 0) - netdev_dbg(dev, "idle transmitter tx2=%d, lasttx=%d, txing=%d\n", + if ((netif_msg_tx_queued(ei_local)) && + ei_local->tx2 > 0) + netdev_dbg(dev, + "idle transmitter tx2=%d, lasttx=%d, txing=%d\n", ei_local->tx2, ei_local->lasttx, ei_local->txing); } else if (ei_local->tx2 == 0) { output_page = ei_local->tx_start_page + TX_PAGES/2; ei_local->tx2 = send_length; - if (ei_debug && ei_local->tx1 > 0) - netdev_dbg(dev, "idle transmitter, tx1=%d, lasttx=%d, txing=%d\n", + if ((netif_msg_tx_queued(ei_local)) && + ei_local->tx1 > 0) + netdev_dbg(dev, + "idle transmitter, tx1=%d, lasttx=%d, txing=%d\n", ei_local->tx1, ei_local->lasttx, ei_local->txing); } else { /* We should never get here. */ - if (ei_debug) - netdev_dbg(dev, "No Tx buffers free! tx1=%d tx2=%d last=%d\n", - ei_local->tx1, ei_local->tx2, ei_local->lasttx); + netif_dbg(ei_local, tx_err, dev, + "No Tx buffers free! tx1=%d tx2=%d last=%d\n", + ei_local->tx1, ei_local->tx2, ei_local->lasttx); ei_local->irqlock = 0; netif_stop_queue(dev); ei_outb_p(ENISR_ALL, e8390_base + EN0_IMR); @@ -388,7 +392,7 @@ static netdev_tx_t __ei_start_xmit(struct sk_buff *skb, } else ei_local->txqueue++; - if (ei_local->tx1 && ei_local->tx2) + if (ei_local->tx1 && ei_local->tx2) netif_stop_queue(dev); else netif_start_queue(dev); @@ -400,7 +404,7 @@ static netdev_tx_t __ei_start_xmit(struct sk_buff *skb, spin_unlock(&ei_local->page_lock); enable_irq_lockdep_irqrestore(dev->irq, &flags); skb_tx_timestamp(skb); - dev_kfree_skb(skb); + dev_consume_skb_any(skb); dev->stats.tx_bytes += send_length; return NETDEV_TX_OK; @@ -445,9 +449,8 @@ static irqreturn_t __ei_interrupt(int irq, void *dev_id) /* Change to page 0 and read the intr status reg. */ ei_outb_p(E8390_NODMA+E8390_PAGE0, e8390_base + E8390_CMD); - if (ei_debug > 3) - netdev_dbg(dev, "interrupt(isr=%#2.2x)\n", - ei_inb_p(e8390_base + EN0_ISR)); + netif_dbg(ei_local, intr, dev, "interrupt(isr=%#2.2x)\n", + ei_inb_p(e8390_base + EN0_ISR)); /* !!Assumption!! -- we stay in page 0. Don't break this. */ while ((interrupts = ei_inb_p(e8390_base + EN0_ISR)) != 0 && @@ -485,7 +488,7 @@ static irqreturn_t __ei_interrupt(int irq, void *dev_id) ei_outb_p(E8390_NODMA+E8390_PAGE0+E8390_START, e8390_base + E8390_CMD); } - if (interrupts && ei_debug) { + if (interrupts && (netif_msg_intr(ei_local))) { ei_outb_p(E8390_NODMA+E8390_PAGE0+E8390_START, e8390_base + E8390_CMD); if (nr_serviced >= MAX_SERVICE) { /* 0xFF is valid for a card removal */ @@ -676,10 +679,11 @@ static void ei_receive(struct net_device *dev) Keep quiet if it looks like a card removal. One problem here is that some clones crash in roughly the same way. */ - if (ei_debug > 0 && + if ((netif_msg_rx_status(ei_local)) && this_frame != ei_local->current_page && (this_frame != 0x0 || rxing_page != 0xFF)) - netdev_err(dev, "mismatched read page pointers %2x vs %2x\n", + netdev_err(dev, + "mismatched read page pointers %2x vs %2x\n", this_frame, ei_local->current_page); if (this_frame == rxing_page) /* Read all the frames? */ @@ -707,10 +711,10 @@ static void ei_receive(struct net_device *dev) } if (pkt_len < 60 || pkt_len > 1518) { - if (ei_debug) - netdev_dbg(dev, "bogus packet size: %d, status=%#2x nxpg=%#2x\n", - rx_frame.count, rx_frame.status, - rx_frame.next); + netif_dbg(ei_local, rx_status, dev, + "bogus packet size: %d, status=%#2x nxpg=%#2x\n", + rx_frame.count, rx_frame.status, + rx_frame.next); dev->stats.rx_errors++; dev->stats.rx_length_errors++; } else if ((pkt_stat & 0x0F) == ENRSR_RXOK) { @@ -718,9 +722,9 @@ static void ei_receive(struct net_device *dev) skb = netdev_alloc_skb(dev, pkt_len + 2); if (skb == NULL) { - if (ei_debug > 1) - netdev_dbg(dev, "Couldn't allocate a sk_buff of size %d\n", - pkt_len); + netif_err(ei_local, rx_err, dev, + "Couldn't allocate a sk_buff of size %d\n", + pkt_len); dev->stats.rx_dropped++; break; } else { @@ -736,10 +740,10 @@ static void ei_receive(struct net_device *dev) dev->stats.multicast++; } } else { - if (ei_debug) - netdev_dbg(dev, "bogus packet: status=%#2x nxpg=%#2x size=%d\n", - rx_frame.status, rx_frame.next, - rx_frame.count); + netif_err(ei_local, rx_err, dev, + "bogus packet: status=%#2x nxpg=%#2x size=%d\n", + rx_frame.status, rx_frame.next, + rx_frame.count); dev->stats.rx_errors++; /* NB: The NIC counts CRC, frame and missed errors. */ if (pkt_stat & ENRSR_FO) @@ -789,8 +793,7 @@ static void ei_rx_overrun(struct net_device *dev) was_txing = ei_inb_p(e8390_base+E8390_CMD) & E8390_TRANS; ei_outb_p(E8390_NODMA+E8390_PAGE0+E8390_STOP, e8390_base+E8390_CMD); - if (ei_debug > 1) - netdev_dbg(dev, "Receiver overrun\n"); + netif_dbg(ei_local, rx_err, dev, "Receiver overrun\n"); dev->stats.rx_over_errors++; /* @@ -965,8 +968,9 @@ static void __ei_set_multicast_list(struct net_device *dev) static void ethdev_setup(struct net_device *dev) { struct ei_device *ei_local = netdev_priv(dev); - if (ei_debug > 1) - printk(version); + + if ((msg_enable & NETIF_MSG_DRV) && (version_printed++ == 0)) + pr_info("%s", version); ether_setup(dev); @@ -1035,9 +1039,10 @@ static void __NS8390_init(struct net_device *dev, int startp) ei_outb_p(E8390_NODMA + E8390_PAGE1 + E8390_STOP, e8390_base+E8390_CMD); /* 0x61 */ for (i = 0; i < 6; i++) { ei_outb_p(dev->dev_addr[i], e8390_base + EN1_PHYS_SHIFT(i)); - if (ei_debug > 1 && + if ((netif_msg_probe(ei_local)) && ei_inb_p(e8390_base + EN1_PHYS_SHIFT(i)) != dev->dev_addr[i]) - netdev_err(dev, "Hw. address read/write mismap %d\n", i); + netdev_err(dev, + "Hw. address read/write mismap %d\n", i); } ei_outb_p(ei_local->rx_start_page, e8390_base + EN1_CURPAG); diff --git a/drivers/net/ethernet/8390/mac8390.c b/drivers/net/ethernet/8390/mac8390.c index 88ccc8b14f0..90e825e8abf 100644 --- a/drivers/net/ethernet/8390/mac8390.c +++ b/drivers/net/ethernet/8390/mac8390.c @@ -167,6 +167,7 @@ static void slow_sane_block_output(struct net_device *dev, int count, const unsigned char *buf, int start_page); static void word_memcpy_tocard(unsigned long tp, const void *fp, int count); static void word_memcpy_fromcard(void *tp, unsigned long fp, int count); +static u32 mac8390_msg_enable; static enum mac8390_type __init mac8390_ident(struct nubus_dev *dev) { @@ -402,6 +403,7 @@ struct net_device * __init mac8390_probe(int unit) struct net_device *dev; struct nubus_dev *ndev = NULL; int err = -ENODEV; + struct ei_device *ei_local; static unsigned int slots; @@ -440,6 +442,10 @@ struct net_device * __init mac8390_probe(int unit) if (!ndev) goto out; + + ei_local = netdev_priv(dev); + ei_local->msg_enable = mac8390_msg_enable; + err = register_netdev(dev); if (err) goto out; @@ -660,19 +666,22 @@ static int mac8390_close(struct net_device *dev) static void mac8390_no_reset(struct net_device *dev) { + struct ei_device *ei_local = netdev_priv(dev); + ei_status.txing = 0; - if (ei_debug > 1) - pr_info("reset not supported\n"); + netif_info(ei_local, hw, dev, "reset not supported\n"); } static void interlan_reset(struct net_device *dev) { unsigned char *target = nubus_slot_addr(IRQ2SLOT(dev->irq)); - if (ei_debug > 1) - pr_info("Need to reset the NS8390 t=%lu...", jiffies); + struct ei_device *ei_local = netdev_priv(dev); + + netif_info(ei_local, hw, dev, "Need to reset the NS8390 t=%lu...", + jiffies); ei_status.txing = 0; target[0xC0000] = 0; - if (ei_debug > 1) + if (netif_msg_hw(ei_local)) pr_cont("reset complete\n"); } diff --git a/drivers/net/ethernet/8390/mcf8390.c b/drivers/net/ethernet/8390/mcf8390.c index 230efd6fa5d..38fcdcf7c4c 100644 --- a/drivers/net/ethernet/8390/mcf8390.c +++ b/drivers/net/ethernet/8390/mcf8390.c @@ -13,7 +13,6 @@ #include <linux/module.h> #include <linux/kernel.h> #include <linux/errno.h> -#include <linux/init.h> #include <linux/platform_device.h> #include <linux/netdevice.h> #include <linux/etherdevice.h> @@ -39,6 +38,7 @@ static const char version[] = #define NESM_START_PG 0x40 /* First page of TX buffer */ #define NESM_STOP_PG 0x80 /* Last page +1 of RX ring */ +static u32 mcf8390_msg_enable; #ifdef NE2000_ODDOFFSET /* @@ -153,9 +153,9 @@ static void mcf8390_reset_8390(struct net_device *dev) { unsigned long reset_start_time = jiffies; u32 addr = dev->base_addr; + struct ei_device *ei_local = netdev_priv(dev); - if (ei_debug > 1) - netdev_dbg(dev, "resetting the 8390 t=%ld...\n", jiffies); + netif_dbg(ei_local, hw, dev, "resetting the 8390 t=%ld...\n", jiffies); ei_outb(ei_inb(addr + NE_RESET), addr + NE_RESET); @@ -288,7 +288,7 @@ static void mcf8390_block_output(struct net_device *dev, int count, dma_start = jiffies; while ((ei_inb(addr + NE_EN0_ISR) & ENISR_RDC) == 0) { if (time_after(jiffies, dma_start + 2 * HZ / 100)) { /* 20ms */ - netdev_err(dev, "timeout waiting for Tx RDC\n"); + netdev_warn(dev, "timeout waiting for Tx RDC\n"); mcf8390_reset_8390(dev); __NS8390_init(dev, 1); break; @@ -437,6 +437,7 @@ static int mcf8390_probe(struct platform_device *pdev) SET_NETDEV_DEV(dev, &pdev->dev); platform_set_drvdata(pdev, dev); ei_local = netdev_priv(dev); + ei_local->msg_enable = mcf8390_msg_enable; dev->irq = irq->start; dev->base_addr = mem->start; diff --git a/drivers/net/ethernet/8390/ne-h8300.c b/drivers/net/ethernet/8390/ne-h8300.c deleted file mode 100644 index 7fc28f2d28a..00000000000 --- a/drivers/net/ethernet/8390/ne-h8300.c +++ /dev/null @@ -1,684 +0,0 @@ -/* ne-h8300.c: A NE2000 clone on H8/300 driver for linux. */ -/* - original ne.c - Written 1992-94 by Donald Becker. - - Copyright 1993 United States Government as represented by the - Director, National Security Agency. - - This software may be used and distributed according to the terms - of the GNU General Public License, incorporated herein by reference. - - The author may be reached as becker@scyld.com, or C/O - Scyld Computing Corporation, 410 Severn Ave., Suite 210, Annapolis MD 21403 - - H8/300 modified - Yoshinori Sato <ysato@users.sourceforge.jp> -*/ - -static const char version1[] = -"ne-h8300.c:v1.00 2004/04/11 ysato\n"; - -#include <linux/module.h> -#include <linux/kernel.h> -#include <linux/errno.h> -#include <linux/init.h> -#include <linux/interrupt.h> -#include <linux/delay.h> -#include <linux/netdevice.h> -#include <linux/etherdevice.h> -#include <linux/jiffies.h> - -#include <asm/io.h> -#include <asm/irq.h> - -#define EI_SHIFT(x) (ei_local->reg_offset[x]) - -#include "8390.h" - -#define DRV_NAME "ne-h8300" - -/* Some defines that people can play with if so inclined. */ - -/* Do we perform extra sanity checks on stuff ? */ -/* #define NE_SANITY_CHECK */ - -/* Do we implement the read before write bugfix ? */ -/* #define NE_RW_BUGFIX */ - -/* Do we have a non std. amount of memory? (in units of 256 byte pages) */ -/* #define PACKETBUF_MEMSIZE 0x40 */ - -/* A zero-terminated list of I/O addresses to be probed at boot. */ - -/* ---- No user-serviceable parts below ---- */ - -static const char version[] = - "8390.c:v1.10cvs 9/23/94 Donald Becker (becker@cesdis.gsfc.nasa.gov)\n"; - -#include "lib8390.c" - -#define NE_BASE (dev->base_addr) -#define NE_CMD 0x00 -#define NE_DATAPORT (ei_status.word16?0x20:0x10) /* NatSemi-defined port window offset. */ -#define NE_RESET (ei_status.word16?0x3f:0x1f) /* Issue a read to reset, a write to clear. */ -#define NE_IO_EXTENT (ei_status.word16?0x40:0x20) - -#define NESM_START_PG 0x40 /* First page of TX buffer */ -#define NESM_STOP_PG 0x80 /* Last page +1 of RX ring */ - -static int ne_probe1(struct net_device *dev, int ioaddr); - -static int ne_open(struct net_device *dev); -static int ne_close(struct net_device *dev); - -static void ne_reset_8390(struct net_device *dev); -static void ne_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr, - int ring_page); -static void ne_block_input(struct net_device *dev, int count, - struct sk_buff *skb, int ring_offset); -static void ne_block_output(struct net_device *dev, const int count, - const unsigned char *buf, const int start_page); - - -static u32 reg_offset[16]; - -static int __init init_reg_offset(struct net_device *dev,unsigned long base_addr) -{ - struct ei_device *ei_local = netdev_priv(dev); - int i; - unsigned char bus_width; - - bus_width = *(volatile unsigned char *)ABWCR; - bus_width &= 1 << ((base_addr >> 21) & 7); - - for (i = 0; i < ARRAY_SIZE(reg_offset); i++) - if (bus_width == 0) - reg_offset[i] = i * 2 + 1; - else - reg_offset[i] = i; - - ei_local->reg_offset = reg_offset; - return 0; -} - -static int __initdata h8300_ne_count = 0; -#ifdef CONFIG_H8300H_H8MAX -static unsigned long __initdata h8300_ne_base[] = { 0x800600 }; -static int h8300_ne_irq[] = {EXT_IRQ4}; -#endif -#ifdef CONFIG_H8300H_AKI3068NET -static unsigned long __initdata h8300_ne_base[] = { 0x200000 }; -static int h8300_ne_irq[] = {EXT_IRQ5}; -#endif - -static inline int init_dev(struct net_device *dev) -{ - if (h8300_ne_count < ARRAY_SIZE(h8300_ne_base)) { - dev->base_addr = h8300_ne_base[h8300_ne_count]; - dev->irq = h8300_ne_irq[h8300_ne_count]; - h8300_ne_count++; - return 0; - } else - return -ENODEV; -} - -/* Probe for various non-shared-memory ethercards. - - NEx000-clone boards have a Station Address PROM (SAPROM) in the packet - buffer memory space. NE2000 clones have 0x57,0x57 in bytes 0x0e,0x0f of - the SAPROM, while other supposed NE2000 clones must be detected by their - SA prefix. - - Reading the SAPROM from a word-wide card with the 8390 set in byte-wide - mode results in doubled values, which can be detected and compensated for. - - The probe is also responsible for initializing the card and filling - in the 'dev' and 'ei_status' structures. - - We use the minimum memory size for some ethercard product lines, iff we can't - distinguish models. You can increase the packet buffer size by setting - PACKETBUF_MEMSIZE. Reported Cabletron packet buffer locations are: - E1010 starts at 0x100 and ends at 0x2000. - E1010-x starts at 0x100 and ends at 0x8000. ("-x" means "more memory") - E2010 starts at 0x100 and ends at 0x4000. - E2010-x starts at 0x100 and ends at 0xffff. */ - -static int __init do_ne_probe(struct net_device *dev) -{ - unsigned int base_addr = dev->base_addr; - - /* First check any supplied i/o locations. User knows best. <cough> */ - if (base_addr > 0x1ff) /* Check a single specified location. */ - return ne_probe1(dev, base_addr); - else if (base_addr != 0) /* Don't probe at all. */ - return -ENXIO; - - return -ENODEV; -} - -static void cleanup_card(struct net_device *dev) -{ - free_irq(dev->irq, dev); - release_region(dev->base_addr, NE_IO_EXTENT); -} - -#ifndef MODULE -struct net_device * __init ne_probe(int unit) -{ - struct net_device *dev = ____alloc_ei_netdev(0); - int err; - - if (!dev) - return ERR_PTR(-ENOMEM); - - if (init_dev(dev)) - return ERR_PTR(-ENODEV); - - sprintf(dev->name, "eth%d", unit); - netdev_boot_setup_check(dev); - - err = init_reg_offset(dev, dev->base_addr); - if (err) - goto out; - - err = do_ne_probe(dev); - if (err) - goto out; - return dev; -out: - free_netdev(dev); - return ERR_PTR(err); -} -#endif - -static const struct net_device_ops ne_netdev_ops = { - .ndo_open = ne_open, - .ndo_stop = ne_close, - - .ndo_start_xmit = __ei_start_xmit, - .ndo_tx_timeout = __ei_tx_timeout, - .ndo_get_stats = __ei_get_stats, - .ndo_set_rx_mode = __ei_set_multicast_list, - .ndo_validate_addr = eth_validate_addr, - .ndo_set_mac_address = eth_mac_addr, - .ndo_change_mtu = eth_change_mtu, -#ifdef CONFIG_NET_POLL_CONTROLLER - .ndo_poll_controller = __ei_poll, -#endif -}; - -static int __init ne_probe1(struct net_device *dev, int ioaddr) -{ - int i; - unsigned char SA_prom[16]; - int wordlength = 2; - const char *name = NULL; - int start_page, stop_page; - int reg0, ret; - static unsigned version_printed; - struct ei_device *ei_local = netdev_priv(dev); - unsigned char bus_width; - - if (!request_region(ioaddr, NE_IO_EXTENT, DRV_NAME)) - return -EBUSY; - - reg0 = inb_p(ioaddr); - if (reg0 == 0xFF) { - ret = -ENODEV; - goto err_out; - } - - /* Do a preliminary verification that we have a 8390. */ - { - int regd; - outb_p(E8390_NODMA+E8390_PAGE1+E8390_STOP, ioaddr + E8390_CMD); - regd = inb_p(ioaddr + EI_SHIFT(0x0d)); - outb_p(0xff, ioaddr + EI_SHIFT(0x0d)); - outb_p(E8390_NODMA+E8390_PAGE0, ioaddr + E8390_CMD); - inb_p(ioaddr + EN0_COUNTER0); /* Clear the counter by reading. */ - if (inb_p(ioaddr + EN0_COUNTER0) != 0) { - outb_p(reg0, ioaddr + EI_SHIFT(0)); - outb_p(regd, ioaddr + EI_SHIFT(0x0d)); /* Restore the old values. */ - ret = -ENODEV; - goto err_out; - } - } - - if (ei_debug && version_printed++ == 0) - printk(KERN_INFO "%s", version1); - - printk(KERN_INFO "NE*000 ethercard probe at %08x:", ioaddr); - - /* Read the 16 bytes of station address PROM. - We must first initialize registers, similar to NS8390_init(eifdev, 0). - We can't reliably read the SAPROM address without this. - (I learned the hard way!). */ - { - struct {unsigned char value, offset; } program_seq[] = - { - {E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD}, /* Select page 0*/ - {0x48, EN0_DCFG}, /* Set byte-wide (0x48) access. */ - {0x00, EN0_RCNTLO}, /* Clear the count regs. */ - {0x00, EN0_RCNTHI}, - {0x00, EN0_IMR}, /* Mask completion irq. */ - {0xFF, EN0_ISR}, - {E8390_RXOFF, EN0_RXCR}, /* 0x20 Set to monitor */ - {E8390_TXOFF, EN0_TXCR}, /* 0x02 and loopback mode. */ - {32, EN0_RCNTLO}, - {0x00, EN0_RCNTHI}, - {0x00, EN0_RSARLO}, /* DMA starting at 0x0000. */ - {0x00, EN0_RSARHI}, - {E8390_RREAD+E8390_START, E8390_CMD}, - }; - - for (i = 0; i < ARRAY_SIZE(program_seq); i++) - outb_p(program_seq[i].value, ioaddr + program_seq[i].offset); - - } - bus_width = *(volatile unsigned char *)ABWCR; - bus_width &= 1 << ((ioaddr >> 21) & 7); - ei_status.word16 = (bus_width == 0); /* temporary setting */ - for(i = 0; i < 16 /*sizeof(SA_prom)*/; i++) { - SA_prom[i] = inb_p(ioaddr + NE_DATAPORT); - inb_p(ioaddr + NE_DATAPORT); /* dummy read */ - } - - start_page = NESM_START_PG; - stop_page = NESM_STOP_PG; - - if (bus_width) - wordlength = 1; - else - outb_p(0x49, ioaddr + EN0_DCFG); - - /* Set up the rest of the parameters. */ - name = (wordlength == 2) ? "NE2000" : "NE1000"; - - if (! dev->irq) { - printk(" failed to detect IRQ line.\n"); - ret = -EAGAIN; - goto err_out; - } - - /* Snarf the interrupt now. There's no point in waiting since we cannot - share and the board will usually be enabled. */ - ret = request_irq(dev->irq, __ei_interrupt, 0, name, dev); - if (ret) { - printk (" unable to get IRQ %d (errno=%d).\n", dev->irq, ret); - goto err_out; - } - - dev->base_addr = ioaddr; - - for (i = 0; i < ETH_ALEN; i++) - dev->dev_addr[i] = SA_prom[i]; - printk(" %pM\n", dev->dev_addr); - - printk("%s: %s found at %#x, using IRQ %d.\n", - dev->name, name, ioaddr, dev->irq); - - ei_status.name = name; - ei_status.tx_start_page = start_page; - ei_status.stop_page = stop_page; - ei_status.word16 = (wordlength == 2); - - ei_status.rx_start_page = start_page + TX_PAGES; -#ifdef PACKETBUF_MEMSIZE - /* Allow the packet buffer size to be overridden by know-it-alls. */ - ei_status.stop_page = ei_status.tx_start_page + PACKETBUF_MEMSIZE; -#endif - - ei_status.reset_8390 = &ne_reset_8390; - ei_status.block_input = &ne_block_input; - ei_status.block_output = &ne_block_output; - ei_status.get_8390_hdr = &ne_get_8390_hdr; - ei_status.priv = 0; - - dev->netdev_ops = &ne_netdev_ops; - - __NS8390_init(dev, 0); - - ret = register_netdev(dev); - if (ret) - goto out_irq; - return 0; -out_irq: - free_irq(dev->irq, dev); -err_out: - release_region(ioaddr, NE_IO_EXTENT); - return ret; -} - -static int ne_open(struct net_device *dev) -{ - __ei_open(dev); - return 0; -} - -static int ne_close(struct net_device *dev) -{ - if (ei_debug > 1) - printk(KERN_DEBUG "%s: Shutting down ethercard.\n", dev->name); - __ei_close(dev); - return 0; -} - -/* Hard reset the card. This used to pause for the same period that a - 8390 reset command required, but that shouldn't be necessary. */ - -static void ne_reset_8390(struct net_device *dev) -{ - unsigned long reset_start_time = jiffies; - struct ei_device *ei_local = netdev_priv(dev); - - if (ei_debug > 1) - printk(KERN_DEBUG "resetting the 8390 t=%ld...", jiffies); - - /* DON'T change these to inb_p/outb_p or reset will fail on clones. */ - outb(inb(NE_BASE + NE_RESET), NE_BASE + NE_RESET); - - ei_status.txing = 0; - ei_status.dmaing = 0; - - /* This check _should_not_ be necessary, omit eventually. */ - while ((inb_p(NE_BASE+EN0_ISR) & ENISR_RESET) == 0) - if (time_after(jiffies, reset_start_time + 2*HZ/100)) { - printk(KERN_WARNING "%s: ne_reset_8390() did not complete.\n", dev->name); - break; - } - outb_p(ENISR_RESET, NE_BASE + EN0_ISR); /* Ack intr. */ -} - -/* Grab the 8390 specific header. Similar to the block_input routine, but - we don't need to be concerned with ring wrap as the header will be at - the start of a page, so we optimize accordingly. */ - -static void ne_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr, int ring_page) -{ - struct ei_device *ei_local = netdev_priv(dev); - /* This *shouldn't* happen. If it does, it's the last thing you'll see */ - - if (ei_status.dmaing) - { - printk(KERN_EMERG "%s: DMAing conflict in ne_get_8390_hdr " - "[DMAstat:%d][irqlock:%d].\n", - dev->name, ei_status.dmaing, ei_status.irqlock); - return; - } - - ei_status.dmaing |= 0x01; - outb_p(E8390_NODMA+E8390_PAGE0+E8390_START, NE_BASE + NE_CMD); - outb_p(sizeof(struct e8390_pkt_hdr), NE_BASE + EN0_RCNTLO); - outb_p(0, NE_BASE + EN0_RCNTHI); - outb_p(0, NE_BASE + EN0_RSARLO); /* On page boundary */ - outb_p(ring_page, NE_BASE + EN0_RSARHI); - outb_p(E8390_RREAD+E8390_START, NE_BASE + NE_CMD); - - if (ei_status.word16) { - int len; - unsigned short *p = (unsigned short *)hdr; - for (len = sizeof(struct e8390_pkt_hdr)>>1; len > 0; len--) - *p++ = inw(NE_BASE + NE_DATAPORT); - } else - insb(NE_BASE + NE_DATAPORT, hdr, sizeof(struct e8390_pkt_hdr)); - - outb_p(ENISR_RDC, NE_BASE + EN0_ISR); /* Ack intr. */ - ei_status.dmaing &= ~0x01; - - le16_to_cpus(&hdr->count); -} - -/* Block input and output, similar to the Crynwr packet driver. If you - are porting to a new ethercard, look at the packet driver source for hints. - The NEx000 doesn't share the on-board packet memory -- you have to put - the packet out through the "remote DMA" dataport using outb. */ - -static void ne_block_input(struct net_device *dev, int count, struct sk_buff *skb, int ring_offset) -{ - struct ei_device *ei_local = netdev_priv(dev); -#ifdef NE_SANITY_CHECK - int xfer_count = count; -#endif - char *buf = skb->data; - - /* This *shouldn't* happen. If it does, it's the last thing you'll see */ - if (ei_status.dmaing) - { - printk(KERN_EMERG "%s: DMAing conflict in ne_block_input " - "[DMAstat:%d][irqlock:%d].\n", - dev->name, ei_status.dmaing, ei_status.irqlock); - return; - } - ei_status.dmaing |= 0x01; - outb_p(E8390_NODMA+E8390_PAGE0+E8390_START, NE_BASE + NE_CMD); - outb_p(count & 0xff, NE_BASE + EN0_RCNTLO); - outb_p(count >> 8, NE_BASE + EN0_RCNTHI); - outb_p(ring_offset & 0xff, NE_BASE + EN0_RSARLO); - outb_p(ring_offset >> 8, NE_BASE + EN0_RSARHI); - outb_p(E8390_RREAD+E8390_START, NE_BASE + NE_CMD); - if (ei_status.word16) - { - int len; - unsigned short *p = (unsigned short *)buf; - for (len = count>>1; len > 0; len--) - *p++ = inw(NE_BASE + NE_DATAPORT); - if (count & 0x01) - { - buf[count-1] = inb(NE_BASE + NE_DATAPORT); -#ifdef NE_SANITY_CHECK - xfer_count++; -#endif - } - } else { - insb(NE_BASE + NE_DATAPORT, buf, count); - } - -#ifdef NE_SANITY_CHECK - /* This was for the ALPHA version only, but enough people have - been encountering problems so it is still here. If you see - this message you either 1) have a slightly incompatible clone - or 2) have noise/speed problems with your bus. */ - - if (ei_debug > 1) - { - /* DMA termination address check... */ - int addr, tries = 20; - do { - /* DON'T check for 'inb_p(EN0_ISR) & ENISR_RDC' here - -- it's broken for Rx on some cards! */ - int high = inb_p(NE_BASE + EN0_RSARHI); - int low = inb_p(NE_BASE + EN0_RSARLO); - addr = (high << 8) + low; - if (((ring_offset + xfer_count) & 0xff) == low) - break; - } while (--tries > 0); - if (tries <= 0) - printk(KERN_WARNING "%s: RX transfer address mismatch," - "%#4.4x (expected) vs. %#4.4x (actual).\n", - dev->name, ring_offset + xfer_count, addr); - } -#endif - outb_p(ENISR_RDC, NE_BASE + EN0_ISR); /* Ack intr. */ - ei_status.dmaing &= ~0x01; -} - -static void ne_block_output(struct net_device *dev, int count, - const unsigned char *buf, const int start_page) -{ - struct ei_device *ei_local = netdev_priv(dev); - unsigned long dma_start; -#ifdef NE_SANITY_CHECK - int retries = 0; -#endif - - /* Round the count up for word writes. Do we need to do this? - What effect will an odd byte count have on the 8390? - I should check someday. */ - - if (ei_status.word16 && (count & 0x01)) - count++; - - /* This *shouldn't* happen. If it does, it's the last thing you'll see */ - if (ei_status.dmaing) - { - printk(KERN_EMERG "%s: DMAing conflict in ne_block_output." - "[DMAstat:%d][irqlock:%d]\n", - dev->name, ei_status.dmaing, ei_status.irqlock); - return; - } - ei_status.dmaing |= 0x01; - /* We should already be in page 0, but to be safe... */ - outb_p(E8390_PAGE0+E8390_START+E8390_NODMA, NE_BASE + NE_CMD); - -#ifdef NE_SANITY_CHECK -retry: -#endif - -#ifdef NE8390_RW_BUGFIX - /* Handle the read-before-write bug the same way as the - Crynwr packet driver -- the NatSemi method doesn't work. - Actually this doesn't always work either, but if you have - problems with your NEx000 this is better than nothing! */ - - outb_p(0x42, NE_BASE + EN0_RCNTLO); - outb_p(0x00, NE_BASE + EN0_RCNTHI); - outb_p(0x42, NE_BASE + EN0_RSARLO); - outb_p(0x00, NE_BASE + EN0_RSARHI); - outb_p(E8390_RREAD+E8390_START, NE_BASE + NE_CMD); - /* Make certain that the dummy read has occurred. */ - udelay(6); -#endif - - outb_p(ENISR_RDC, NE_BASE + EN0_ISR); - - /* Now the normal output. */ - outb_p(count & 0xff, NE_BASE + EN0_RCNTLO); - outb_p(count >> 8, NE_BASE + EN0_RCNTHI); - outb_p(0x00, NE_BASE + EN0_RSARLO); - outb_p(start_page, NE_BASE + EN0_RSARHI); - - outb_p(E8390_RWRITE+E8390_START, NE_BASE + NE_CMD); - if (ei_status.word16) { - int len; - unsigned short *p = (unsigned short *)buf; - for (len = count>>1; len > 0; len--) - outw(*p++, NE_BASE + NE_DATAPORT); - } else { - outsb(NE_BASE + NE_DATAPORT, buf, count); - } - - dma_start = jiffies; - -#ifdef NE_SANITY_CHECK - /* This was for the ALPHA version only, but enough people have - been encountering problems so it is still here. */ - - if (ei_debug > 1) - { - /* DMA termination address check... */ - int addr, tries = 20; - do { - int high = inb_p(NE_BASE + EN0_RSARHI); - int low = inb_p(NE_BASE + EN0_RSARLO); - addr = (high << 8) + low; - if ((start_page << 8) + count == addr) - break; - } while (--tries > 0); - - if (tries <= 0) - { - printk(KERN_WARNING "%s: Tx packet transfer address mismatch," - "%#4.4x (expected) vs. %#4.4x (actual).\n", - dev->name, (start_page << 8) + count, addr); - if (retries++ == 0) - goto retry; - } - } -#endif - - while ((inb_p(NE_BASE + EN0_ISR) & ENISR_RDC) == 0) - if (time_after(jiffies, dma_start + 2*HZ/100)) { /* 20ms */ - printk(KERN_WARNING "%s: timeout waiting for Tx RDC.\n", dev->name); - ne_reset_8390(dev); - __NS8390_init(dev,1); - break; - } - - outb_p(ENISR_RDC, NE_BASE + EN0_ISR); /* Ack intr. */ - ei_status.dmaing &= ~0x01; -} - - -#ifdef MODULE -#define MAX_NE_CARDS 1 /* Max number of NE cards per module */ -static struct net_device *dev_ne[MAX_NE_CARDS]; -static int io[MAX_NE_CARDS]; -static int irq[MAX_NE_CARDS]; -static int bad[MAX_NE_CARDS]; /* 0xbad = bad sig or no reset ack */ - -module_param_array(io, int, NULL, 0); -module_param_array(irq, int, NULL, 0); -module_param_array(bad, int, NULL, 0); -MODULE_PARM_DESC(io, "I/O base address(es)"); -MODULE_PARM_DESC(irq, "IRQ number(s)"); -MODULE_DESCRIPTION("H8/300 NE2000 Ethernet driver"); -MODULE_LICENSE("GPL"); - -/* This is set up so that no ISA autoprobe takes place. We can't guarantee -that the ne2k probe is the last 8390 based probe to take place (as it -is at boot) and so the probe will get confused by any other 8390 cards. -ISA device autoprobes on a running machine are not recommended anyway. */ - -int init_module(void) -{ - int this_dev, found = 0; - int err; - - for (this_dev = 0; this_dev < MAX_NE_CARDS; this_dev++) { - struct net_device *dev = ____alloc_ei_netdev(0); - if (!dev) - break; - if (io[this_dev]) { - dev->irq = irq[this_dev]; - dev->mem_end = bad[this_dev]; - dev->base_addr = io[this_dev]; - } else { - dev->base_addr = h8300_ne_base[this_dev]; - dev->irq = h8300_ne_irq[this_dev]; - } - err = init_reg_offset(dev, dev->base_addr); - if (!err) { - if (do_ne_probe(dev) == 0) { - dev_ne[found++] = dev; - continue; - } - } - free_netdev(dev); - if (found) - break; - if (io[this_dev] != 0) - printk(KERN_WARNING "ne.c: No NE*000 card found at i/o = %#x\n", dev->base_addr); - else - printk(KERN_NOTICE "ne.c: You must supply \"io=0xNNN\" value(s) for ISA cards.\n"); - return -ENXIO; - } - if (found) - return 0; - return -ENODEV; -} - -void cleanup_module(void) -{ - int this_dev; - - for (this_dev = 0; this_dev < MAX_NE_CARDS; this_dev++) { - struct net_device *dev = dev_ne[this_dev]; - if (dev) { - unregister_netdev(dev); - cleanup_card(dev); - free_netdev(dev); - } - } -} -#endif /* MODULE */ diff --git a/drivers/net/ethernet/8390/ne.c b/drivers/net/ethernet/8390/ne.c index b2e84051373..58eaa8f3494 100644 --- a/drivers/net/ethernet/8390/ne.c +++ b/drivers/net/ethernet/8390/ne.c @@ -71,14 +71,17 @@ static struct platform_device *pdev_ne[MAX_NE_CARDS]; static int io[MAX_NE_CARDS]; static int irq[MAX_NE_CARDS]; static int bad[MAX_NE_CARDS]; +static u32 ne_msg_enable; #ifdef MODULE module_param_array(io, int, NULL, 0); module_param_array(irq, int, NULL, 0); module_param_array(bad, int, NULL, 0); +module_param_named(msg_enable, ne_msg_enable, uint, (S_IRUSR|S_IRGRP|S_IROTH)); MODULE_PARM_DESC(io, "I/O base address(es),required"); MODULE_PARM_DESC(irq, "IRQ number(s)"); MODULE_PARM_DESC(bad, "Accept card(s) with bad signatures"); +MODULE_PARM_DESC(msg_enable, "Debug message level (see linux/netdevice.h for bitmap)"); MODULE_DESCRIPTION("NE1000/NE2000 ISA/PnP Ethernet driver"); MODULE_LICENSE("GPL"); #endif /* MODULE */ @@ -214,8 +217,8 @@ static int __init do_ne_probe(struct net_device *dev) if (base_addr > 0x1ff) { /* Check a single specified location. */ int ret = ne_probe1(dev, base_addr); if (ret) - printk(KERN_WARNING "ne.c: No NE*000 card found at " - "i/o = %#lx\n", base_addr); + netdev_warn(dev, "ne.c: No NE*000 card found at " + "i/o = %#lx\n", base_addr); return ret; } else if (base_addr != 0) /* Don't probe at all. */ @@ -264,11 +267,14 @@ static int __init ne_probe_isapnp(struct net_device *dev) /* found it */ dev->base_addr = pnp_port_start(idev, 0); dev->irq = pnp_irq(idev, 0); - printk(KERN_INFO "ne.c: ISAPnP reports %s at i/o %#lx, irq %d.\n", - (char *) isapnp_clone_list[i].driver_data, - dev->base_addr, dev->irq); + netdev_info(dev, + "ne.c: ISAPnP reports %s at i/o %#lx, irq %d.\n", + (char *) isapnp_clone_list[i].driver_data, + dev->base_addr, dev->irq); if (ne_probe1(dev, dev->base_addr) != 0) { /* Shouldn't happen. */ - printk(KERN_ERR "ne.c: Probe of ISAPnP card at %#lx failed.\n", dev->base_addr); + netdev_err(dev, + "ne.c: Probe of ISAPnP card at %#lx failed.\n", + dev->base_addr); pnp_device_detach(idev); return -ENXIO; } @@ -293,6 +299,7 @@ static int __init ne_probe1(struct net_device *dev, unsigned long ioaddr) int neX000, ctron, copam, bad_card; int reg0, ret; static unsigned version_printed; + struct ei_device *ei_local = netdev_priv(dev); if (!request_region(ioaddr, NE_IO_EXTENT, DRV_NAME)) return -EBUSY; @@ -319,10 +326,10 @@ static int __init ne_probe1(struct net_device *dev, unsigned long ioaddr) } } - if (ei_debug && version_printed++ == 0) - printk(KERN_INFO "%s%s", version1, version2); + if ((ne_msg_enable & NETIF_MSG_DRV) && (version_printed++ == 0)) + netdev_info(dev, "%s%s", version1, version2); - printk(KERN_INFO "NE*000 ethercard probe at %#3lx:", ioaddr); + netdev_info(dev, "NE*000 ethercard probe at %#3lx:", ioaddr); /* A user with a poor card that fails to ack the reset, or that does not have a valid 0x57,0x57 signature can still use this @@ -343,10 +350,10 @@ static int __init ne_probe1(struct net_device *dev, unsigned long ioaddr) while ((inb_p(ioaddr + EN0_ISR) & ENISR_RESET) == 0) if (time_after(jiffies, reset_start_time + 2*HZ/100)) { if (bad_card) { - printk(" (warning: no reset ack)"); + pr_cont(" (warning: no reset ack)"); break; } else { - printk(" not found (no reset ack).\n"); + pr_cont(" not found (no reset ack).\n"); ret = -ENODEV; goto err_out; } @@ -454,13 +461,13 @@ static int __init ne_probe1(struct net_device *dev, unsigned long ioaddr) } if (bad_clone_list[i].name8 == NULL) { - printk(" not found (invalid signature %2.2x %2.2x).\n", + pr_cont(" not found (invalid signature %2.2x %2.2x).\n", SA_prom[14], SA_prom[15]); ret = -ENXIO; goto err_out; } #else - printk(" not found.\n"); + pr_cont(" not found.\n"); ret = -ENXIO; goto err_out; #endif @@ -476,15 +483,15 @@ static int __init ne_probe1(struct net_device *dev, unsigned long ioaddr) mdelay(10); /* wait 10ms for interrupt to propagate */ outb_p(0x00, ioaddr + EN0_IMR); /* Mask it again. */ dev->irq = probe_irq_off(cookie); - if (ei_debug > 2) - printk(" autoirq is %d\n", dev->irq); + if (netif_msg_probe(ei_local)) + pr_cont(" autoirq is %d", dev->irq); } else if (dev->irq == 2) /* Fixup for users that don't know that IRQ 2 is really IRQ 9, or don't know which one to set. */ dev->irq = 9; if (! dev->irq) { - printk(" failed to detect IRQ line.\n"); + pr_cont(" failed to detect IRQ line.\n"); ret = -EAGAIN; goto err_out; } @@ -493,7 +500,7 @@ static int __init ne_probe1(struct net_device *dev, unsigned long ioaddr) share and the board will usually be enabled. */ ret = request_irq(dev->irq, eip_interrupt, 0, name, dev); if (ret) { - printk (" unable to get IRQ %d (errno=%d).\n", dev->irq, ret); + pr_cont(" unable to get IRQ %d (errno=%d).\n", dev->irq, ret); goto err_out; } @@ -512,7 +519,7 @@ static int __init ne_probe1(struct net_device *dev, unsigned long ioaddr) } #endif - printk("%pM\n", dev->dev_addr); + pr_cont("%pM\n", dev->dev_addr); ei_status.name = name; ei_status.tx_start_page = start_page; @@ -536,11 +543,12 @@ static int __init ne_probe1(struct net_device *dev, unsigned long ioaddr) dev->netdev_ops = &eip_netdev_ops; NS8390p_init(dev, 0); + ei_local->msg_enable = ne_msg_enable; ret = register_netdev(dev); if (ret) goto out_irq; - printk(KERN_INFO "%s: %s found at %#lx, using IRQ %d.\n", - dev->name, name, ioaddr, dev->irq); + netdev_info(dev, "%s found at %#lx, using IRQ %d.\n", + name, ioaddr, dev->irq); return 0; out_irq: @@ -556,9 +564,9 @@ err_out: static void ne_reset_8390(struct net_device *dev) { unsigned long reset_start_time = jiffies; + struct ei_device *ei_local = netdev_priv(dev); - if (ei_debug > 1) - printk(KERN_DEBUG "resetting the 8390 t=%ld...", jiffies); + netif_dbg(ei_local, hw, dev, "resetting the 8390 t=%ld...\n", jiffies); /* DON'T change these to inb_p/outb_p or reset will fail on clones. */ outb(inb(NE_BASE + NE_RESET), NE_BASE + NE_RESET); @@ -569,7 +577,7 @@ static void ne_reset_8390(struct net_device *dev) /* This check _should_not_ be necessary, omit eventually. */ while ((inb_p(NE_BASE+EN0_ISR) & ENISR_RESET) == 0) if (time_after(jiffies, reset_start_time + 2*HZ/100)) { - printk(KERN_WARNING "%s: ne_reset_8390() did not complete.\n", dev->name); + netdev_err(dev, "ne_reset_8390() did not complete.\n"); break; } outb_p(ENISR_RESET, NE_BASE + EN0_ISR); /* Ack intr. */ @@ -587,9 +595,9 @@ static void ne_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr, i if (ei_status.dmaing) { - printk(KERN_EMERG "%s: DMAing conflict in ne_get_8390_hdr " - "[DMAstat:%d][irqlock:%d].\n", - dev->name, ei_status.dmaing, ei_status.irqlock); + netdev_err(dev, "DMAing conflict in ne_get_8390_hdr " + "[DMAstat:%d][irqlock:%d].\n", + ei_status.dmaing, ei_status.irqlock); return; } @@ -621,6 +629,7 @@ static void ne_block_input(struct net_device *dev, int count, struct sk_buff *sk { #ifdef NE_SANITY_CHECK int xfer_count = count; + struct ei_device *ei_local = netdev_priv(dev); #endif int nic_base = dev->base_addr; char *buf = skb->data; @@ -628,9 +637,9 @@ static void ne_block_input(struct net_device *dev, int count, struct sk_buff *sk /* This *shouldn't* happen. If it does, it's the last thing you'll see */ if (ei_status.dmaing) { - printk(KERN_EMERG "%s: DMAing conflict in ne_block_input " - "[DMAstat:%d][irqlock:%d].\n", - dev->name, ei_status.dmaing, ei_status.irqlock); + netdev_err(dev, "DMAing conflict in ne_block_input " + "[DMAstat:%d][irqlock:%d].\n", + ei_status.dmaing, ei_status.irqlock); return; } ei_status.dmaing |= 0x01; @@ -660,7 +669,7 @@ static void ne_block_input(struct net_device *dev, int count, struct sk_buff *sk this message you either 1) have a slightly incompatible clone or 2) have noise/speed problems with your bus. */ - if (ei_debug > 1) + if (netif_msg_rx_status(ei_local)) { /* DMA termination address check... */ int addr, tries = 20; @@ -674,9 +683,9 @@ static void ne_block_input(struct net_device *dev, int count, struct sk_buff *sk break; } while (--tries > 0); if (tries <= 0) - printk(KERN_WARNING "%s: RX transfer address mismatch," - "%#4.4x (expected) vs. %#4.4x (actual).\n", - dev->name, ring_offset + xfer_count, addr); + netdev_warn(dev, "RX transfer address mismatch," + "%#4.4x (expected) vs. %#4.4x (actual).\n", + ring_offset + xfer_count, addr); } #endif outb_p(ENISR_RDC, nic_base + EN0_ISR); /* Ack intr. */ @@ -690,6 +699,7 @@ static void ne_block_output(struct net_device *dev, int count, unsigned long dma_start; #ifdef NE_SANITY_CHECK int retries = 0; + struct ei_device *ei_local = netdev_priv(dev); #endif /* Round the count up for word writes. Do we need to do this? @@ -702,9 +712,9 @@ static void ne_block_output(struct net_device *dev, int count, /* This *shouldn't* happen. If it does, it's the last thing you'll see */ if (ei_status.dmaing) { - printk(KERN_EMERG "%s: DMAing conflict in ne_block_output." - "[DMAstat:%d][irqlock:%d]\n", - dev->name, ei_status.dmaing, ei_status.irqlock); + netdev_err(dev, "DMAing conflict in ne_block_output." + "[DMAstat:%d][irqlock:%d]\n", + ei_status.dmaing, ei_status.irqlock); return; } ei_status.dmaing |= 0x01; @@ -751,7 +761,7 @@ retry: /* This was for the ALPHA version only, but enough people have been encountering problems so it is still here. */ - if (ei_debug > 1) + if (netif_msg_tx_queued(ei_local)) { /* DMA termination address check... */ int addr, tries = 20; @@ -765,9 +775,9 @@ retry: if (tries <= 0) { - printk(KERN_WARNING "%s: Tx packet transfer address mismatch," - "%#4.4x (expected) vs. %#4.4x (actual).\n", - dev->name, (start_page << 8) + count, addr); + netdev_warn(dev, "Tx packet transfer address mismatch," + "%#4.4x (expected) vs. %#4.4x (actual).\n", + (start_page << 8) + count, addr); if (retries++ == 0) goto retry; } @@ -776,7 +786,7 @@ retry: while ((inb_p(nic_base + EN0_ISR) & ENISR_RDC) == 0) if (time_after(jiffies, dma_start + 2*HZ/100)) { /* 20ms */ - printk(KERN_WARNING "%s: timeout waiting for Tx RDC.\n", dev->name); + netdev_warn(dev, "timeout waiting for Tx RDC.\n"); ne_reset_8390(dev); NS8390p_init(dev, 1); break; @@ -936,8 +946,8 @@ int __init init_module(void) retval = platform_driver_probe(&ne_driver, ne_drv_probe); if (retval) { if (io[0] == 0) - printk(KERN_NOTICE "ne.c: You must supply \"io=0xNNN\"" - " value(s) for ISA cards.\n"); + pr_notice("ne.c: You must supply \"io=0xNNN\"" + " value(s) for ISA cards.\n"); ne_loop_rm_unreg(1); return retval; } diff --git a/drivers/net/ethernet/8390/ne2k-pci.c b/drivers/net/ethernet/8390/ne2k-pci.c index 92201080e07..f395c967262 100644 --- a/drivers/net/ethernet/8390/ne2k-pci.c +++ b/drivers/net/ethernet/8390/ne2k-pci.c @@ -33,8 +33,6 @@ /* The user-configurable values. These may be modified when a driver module is loaded.*/ -static int debug = 1; /* 1 normal messages, 0 quiet .. 7 verbose. */ - #define MAX_UNITS 8 /* More are supported, limit only on options */ /* Used to pass the full-duplex flag, etc. */ static int full_duplex[MAX_UNITS]; @@ -60,6 +58,8 @@ static int options[MAX_UNITS]; #include "8390.h" +static u32 ne2k_msg_enable; + /* These identify the driver base version and may not be removed. */ static const char version[] = KERN_INFO DRV_NAME ".c:v" DRV_VERSION " " DRV_RELDATE @@ -76,10 +76,10 @@ MODULE_AUTHOR("Donald Becker / Paul Gortmaker"); MODULE_DESCRIPTION("PCI NE2000 clone driver"); MODULE_LICENSE("GPL"); -module_param(debug, int, 0); +module_param_named(msg_enable, ne2k_msg_enable, uint, (S_IRUSR|S_IRGRP|S_IROTH)); module_param_array(options, int, NULL, 0); module_param_array(full_duplex, int, NULL, 0); -MODULE_PARM_DESC(debug, "debug level (1-2)"); +MODULE_PARM_DESC(msg_enable, "Debug message level (see linux/netdevice.h for bitmap)"); MODULE_PARM_DESC(options, "Bit 5: full duplex"); MODULE_PARM_DESC(full_duplex, "full duplex setting(s) (1)"); @@ -226,6 +226,7 @@ static int ne2k_pci_init_one(struct pci_dev *pdev, static unsigned int fnd_cnt; long ioaddr; int flags = pci_clone_list[chip_idx].flags; + struct ei_device *ei_local; /* when built into the kernel, we only print version if device is found */ #ifndef MODULE @@ -280,6 +281,8 @@ static int ne2k_pci_init_one(struct pci_dev *pdev, goto err_out_free_res; } dev->netdev_ops = &ne2k_netdev_ops; + ei_local = netdev_priv(dev); + ei_local->msg_enable = ne2k_msg_enable; SET_NETDEV_DEV(dev, &pdev->dev); @@ -379,9 +382,9 @@ static int ne2k_pci_init_one(struct pci_dev *pdev, if (i) goto err_out_free_netdev; - printk("%s: %s found at %#lx, IRQ %d, %pM.\n", - dev->name, pci_clone_list[chip_idx].name, ioaddr, dev->irq, - dev->dev_addr); + netdev_info(dev, "%s found at %#lx, IRQ %d, %pM.\n", + pci_clone_list[chip_idx].name, ioaddr, dev->irq, + dev->dev_addr); return 0; @@ -389,9 +392,7 @@ err_out_free_netdev: free_netdev (dev); err_out_free_res: release_region (ioaddr, NE_IO_EXTENT); - pci_set_drvdata (pdev, NULL); return -ENODEV; - } /* @@ -452,9 +453,10 @@ static int ne2k_pci_close(struct net_device *dev) static void ne2k_pci_reset_8390(struct net_device *dev) { unsigned long reset_start_time = jiffies; + struct ei_device *ei_local = netdev_priv(dev); - if (debug > 1) printk("%s: Resetting the 8390 t=%ld...", - dev->name, jiffies); + netif_dbg(ei_local, hw, dev, "resetting the 8390 t=%ld...\n", + jiffies); outb(inb(NE_BASE + NE_RESET), NE_BASE + NE_RESET); @@ -464,7 +466,7 @@ static void ne2k_pci_reset_8390(struct net_device *dev) /* This check _should_not_ be necessary, omit eventually. */ while ((inb(NE_BASE+EN0_ISR) & ENISR_RESET) == 0) if (jiffies - reset_start_time > 2) { - printk("%s: ne2k_pci_reset_8390() did not complete.\n", dev->name); + netdev_err(dev, "ne2k_pci_reset_8390() did not complete.\n"); break; } outb(ENISR_RESET, NE_BASE + EN0_ISR); /* Ack intr. */ @@ -481,9 +483,9 @@ static void ne2k_pci_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr * /* This *shouldn't* happen. If it does, it's the last thing you'll see */ if (ei_status.dmaing) { - printk("%s: DMAing conflict in ne2k_pci_get_8390_hdr " + netdev_err(dev, "DMAing conflict in ne2k_pci_get_8390_hdr " "[DMAstat:%d][irqlock:%d].\n", - dev->name, ei_status.dmaing, ei_status.irqlock); + ei_status.dmaing, ei_status.irqlock); return; } @@ -519,9 +521,9 @@ static void ne2k_pci_block_input(struct net_device *dev, int count, /* This *shouldn't* happen. If it does, it's the last thing you'll see */ if (ei_status.dmaing) { - printk("%s: DMAing conflict in ne2k_pci_block_input " + netdev_err(dev, "DMAing conflict in ne2k_pci_block_input " "[DMAstat:%d][irqlock:%d].\n", - dev->name, ei_status.dmaing, ei_status.irqlock); + ei_status.dmaing, ei_status.irqlock); return; } ei_status.dmaing |= 0x01; @@ -574,9 +576,9 @@ static void ne2k_pci_block_output(struct net_device *dev, int count, /* This *shouldn't* happen. If it does, it's the last thing you'll see */ if (ei_status.dmaing) { - printk("%s: DMAing conflict in ne2k_pci_block_output." + netdev_err(dev, "DMAing conflict in ne2k_pci_block_output." "[DMAstat:%d][irqlock:%d]\n", - dev->name, ei_status.dmaing, ei_status.irqlock); + ei_status.dmaing, ei_status.irqlock); return; } ei_status.dmaing |= 0x01; @@ -621,7 +623,7 @@ static void ne2k_pci_block_output(struct net_device *dev, int count, while ((inb(nic_base + EN0_ISR) & ENISR_RDC) == 0) if (jiffies - dma_start > 2) { /* Avoid clock roll-over. */ - printk(KERN_WARNING "%s: timeout waiting for Tx RDC.\n", dev->name); + netdev_warn(dev, "timeout waiting for Tx RDC.\n"); ne2k_pci_reset_8390(dev); NS8390_init(dev,1); break; @@ -642,8 +644,24 @@ static void ne2k_pci_get_drvinfo(struct net_device *dev, strlcpy(info->bus_info, pci_name(pci_dev), sizeof(info->bus_info)); } +static u32 ne2k_pci_get_msglevel(struct net_device *dev) +{ + struct ei_device *ei_local = netdev_priv(dev); + + return ei_local->msg_enable; +} + +static void ne2k_pci_set_msglevel(struct net_device *dev, u32 v) +{ + struct ei_device *ei_local = netdev_priv(dev); + + ei_local->msg_enable = v; +} + static const struct ethtool_ops ne2k_pci_ethtool_ops = { .get_drvinfo = ne2k_pci_get_drvinfo, + .get_msglevel = ne2k_pci_get_msglevel, + .set_msglevel = ne2k_pci_set_msglevel, }; static void ne2k_pci_remove_one(struct pci_dev *pdev) @@ -655,7 +673,6 @@ static void ne2k_pci_remove_one(struct pci_dev *pdev) release_region(dev->base_addr, NE_IO_EXTENT); free_netdev(dev); pci_disable_device(pdev); - pci_set_drvdata(pdev, NULL); } #ifdef CONFIG_PM diff --git a/drivers/net/ethernet/8390/pcnet_cs.c b/drivers/net/ethernet/8390/pcnet_cs.c index 46c5aadaca8..ca3c2b921cf 100644 --- a/drivers/net/ethernet/8390/pcnet_cs.c +++ b/drivers/net/ethernet/8390/pcnet_cs.c @@ -32,7 +32,6 @@ #include <linux/kernel.h> #include <linux/module.h> -#include <linux/init.h> #include <linux/ptrace.h> #include <linux/string.h> #include <linux/timer.h> @@ -67,7 +66,7 @@ #define PCNET_RDC_TIMEOUT (2*HZ/100) /* Max wait in jiffies for Tx RDC */ static const char *if_names[] = { "auto", "10baseT", "10base2"}; - +static u32 pcnet_msg_enable; /*====================================================================*/ @@ -558,6 +557,7 @@ static int pcnet_config(struct pcmcia_device *link) int start_pg, stop_pg, cm_offset; int has_shmem = 0; hw_info_t *local_hw_info; + struct ei_device *ei_local; dev_dbg(&link->dev, "pcnet_config\n"); @@ -607,6 +607,8 @@ static int pcnet_config(struct pcmcia_device *link) mii_phy_probe(dev); SET_NETDEV_DEV(dev, &link->dev); + ei_local = netdev_priv(dev); + ei_local->msg_enable = pcnet_msg_enable; if (register_netdev(dev) != 0) { pr_notice("register_netdev() failed\n"); @@ -616,7 +618,7 @@ static int pcnet_config(struct pcmcia_device *link) if (info->flags & (IS_DL10019|IS_DL10022)) { u_char id = inb(dev->base_addr + 0x1a); netdev_info(dev, "NE2000 (DL100%d rev %02x): ", - (info->flags & IS_DL10022) ? 22 : 19, id); + (info->flags & IS_DL10022) ? 22 : 19, id); if (info->pna_phy) pr_cont("PNA, "); } else { @@ -1063,9 +1065,9 @@ static void ei_watchdog(u_long arg) if (info->phy_id == info->eth_phy) { if (p) netdev_info(dev, "autonegotiation complete: " - "%sbaseT-%cD selected\n", - ((p & 0x0180) ? "100" : "10"), - ((p & 0x0140) ? 'F' : 'H')); + "%sbaseT-%cD selected\n", + ((p & 0x0180) ? "100" : "10"), + ((p & 0x0140) ? 'F' : 'H')); else netdev_info(dev, "link partner did not autonegotiate\n"); } @@ -1081,7 +1083,7 @@ static void ei_watchdog(u_long arg) mdio_write(mii_addr, info->phy_id, 0, 0x0400); info->phy_id ^= info->pna_phy ^ info->eth_phy; netdev_info(dev, "switched to %s transceiver\n", - (info->phy_id == info->eth_phy) ? "ethernet" : "PNA"); + (info->phy_id == info->eth_phy) ? "ethernet" : "PNA"); mdio_write(mii_addr, info->phy_id, 0, (info->phy_id == info->eth_phy) ? 0x1000 : 0); info->link_status = 0; @@ -1128,9 +1130,9 @@ static void dma_get_8390_hdr(struct net_device *dev, unsigned int nic_base = dev->base_addr; if (ei_status.dmaing) { - netdev_notice(dev, "DMAing conflict in dma_block_input." - "[DMAstat:%1x][irqlock:%1x]\n", - ei_status.dmaing, ei_status.irqlock); + netdev_err(dev, "DMAing conflict in dma_block_input." + "[DMAstat:%1x][irqlock:%1x]\n", + ei_status.dmaing, ei_status.irqlock); return; } @@ -1159,13 +1161,14 @@ static void dma_block_input(struct net_device *dev, int count, unsigned int nic_base = dev->base_addr; int xfer_count = count; char *buf = skb->data; + struct ei_device *ei_local = netdev_priv(dev); - if ((ei_debug > 4) && (count != 4)) + if ((netif_msg_rx_status(ei_local)) && (count != 4)) netdev_dbg(dev, "[bi=%d]\n", count+4); if (ei_status.dmaing) { - netdev_notice(dev, "DMAing conflict in dma_block_input." - "[DMAstat:%1x][irqlock:%1x]\n", - ei_status.dmaing, ei_status.irqlock); + netdev_err(dev, "DMAing conflict in dma_block_input." + "[DMAstat:%1x][irqlock:%1x]\n", + ei_status.dmaing, ei_status.irqlock); return; } ei_status.dmaing |= 0x01; @@ -1183,7 +1186,8 @@ static void dma_block_input(struct net_device *dev, int count, /* This was for the ALPHA version only, but enough people have been encountering problems that it is still here. */ #ifdef PCMCIA_DEBUG - if (ei_debug > 4) { /* DMA termination address check... */ + /* DMA termination address check... */ + if (netif_msg_rx_status(ei_local)) { int addr, tries = 20; do { /* DON'T check for 'inb_p(EN0_ISR) & ENISR_RDC' here @@ -1196,8 +1200,8 @@ static void dma_block_input(struct net_device *dev, int count, } while (--tries > 0); if (tries <= 0) netdev_notice(dev, "RX transfer address mismatch," - "%#4.4x (expected) vs. %#4.4x (actual).\n", - ring_offset + xfer_count, addr); + "%#4.4x (expected) vs. %#4.4x (actual).\n", + ring_offset + xfer_count, addr); } #endif outb_p(ENISR_RDC, nic_base + EN0_ISR); /* Ack intr. */ @@ -1213,12 +1217,12 @@ static void dma_block_output(struct net_device *dev, int count, pcnet_dev_t *info = PRIV(dev); #ifdef PCMCIA_DEBUG int retries = 0; + struct ei_device *ei_local = netdev_priv(dev); #endif u_long dma_start; #ifdef PCMCIA_DEBUG - if (ei_debug > 4) - netdev_dbg(dev, "[bo=%d]\n", count); + netif_dbg(ei_local, tx_queued, dev, "[bo=%d]\n", count); #endif /* Round the count up for word writes. Do we need to do this? @@ -1227,9 +1231,9 @@ static void dma_block_output(struct net_device *dev, int count, if (count & 0x01) count++; if (ei_status.dmaing) { - netdev_notice(dev, "DMAing conflict in dma_block_output." - "[DMAstat:%1x][irqlock:%1x]\n", - ei_status.dmaing, ei_status.irqlock); + netdev_err(dev, "DMAing conflict in dma_block_output." + "[DMAstat:%1x][irqlock:%1x]\n", + ei_status.dmaing, ei_status.irqlock); return; } ei_status.dmaing |= 0x01; @@ -1256,7 +1260,8 @@ static void dma_block_output(struct net_device *dev, int count, #ifdef PCMCIA_DEBUG /* This was for the ALPHA version only, but enough people have been encountering problems that it is still here. */ - if (ei_debug > 4) { /* DMA termination address check... */ + /* DMA termination address check... */ + if (netif_msg_tx_queued(ei_local)) { int addr, tries = 20; do { int high = inb_p(nic_base + EN0_RSARHI); @@ -1267,8 +1272,8 @@ static void dma_block_output(struct net_device *dev, int count, } while (--tries > 0); if (tries <= 0) { netdev_notice(dev, "Tx packet transfer address mismatch," - "%#4.4x (expected) vs. %#4.4x (actual).\n", - (start_page << 8) + count, addr); + "%#4.4x (expected) vs. %#4.4x (actual).\n", + (start_page << 8) + count, addr); if (retries++ == 0) goto retry; } @@ -1277,10 +1282,10 @@ static void dma_block_output(struct net_device *dev, int count, while ((inb_p(nic_base + EN0_ISR) & ENISR_RDC) == 0) if (time_after(jiffies, dma_start + PCNET_RDC_TIMEOUT)) { - netdev_notice(dev, "timeout waiting for Tx RDC.\n"); - pcnet_reset_8390(dev); - NS8390_init(dev, 1); - break; + netdev_warn(dev, "timeout waiting for Tx RDC.\n"); + pcnet_reset_8390(dev); + NS8390_init(dev, 1); + break; } outb_p(ENISR_RDC, nic_base + EN0_ISR); /* Ack intr. */ diff --git a/drivers/net/ethernet/8390/smc-ultra.c b/drivers/net/ethernet/8390/smc-ultra.c index b0fbce39661..139385dcdaa 100644 --- a/drivers/net/ethernet/8390/smc-ultra.c +++ b/drivers/net/ethernet/8390/smc-ultra.c @@ -111,6 +111,7 @@ static struct isapnp_device_id ultra_device_ids[] __initdata = { MODULE_DEVICE_TABLE(isapnp, ultra_device_ids); #endif +static u32 ultra_msg_enable; #define START_PG 0x00 /* First page of TX buffer */ @@ -211,6 +212,7 @@ static int __init ultra_probe1(struct net_device *dev, int ioaddr) unsigned char num_pages, irqreg, addr, piomode; unsigned char idreg = inb(ioaddr + 7); unsigned char reg4 = inb(ioaddr + 4) & 0x7f; + struct ei_device *ei_local = netdev_priv(dev); if (!request_region(ioaddr, ULTRA_IO_EXTENT, DRV_NAME)) return -EBUSY; @@ -232,16 +234,16 @@ static int __init ultra_probe1(struct net_device *dev, int ioaddr) goto out; } - if (ei_debug && version_printed++ == 0) - printk(version); + if ((ultra_msg_enable & NETIF_MSG_DRV) && (version_printed++ == 0)) + netdev_info(dev, version); model_name = (idreg & 0xF0) == 0x20 ? "SMC Ultra" : "SMC EtherEZ"; for (i = 0; i < 6; i++) dev->dev_addr[i] = inb(ioaddr + 8 + i); - printk("%s: %s at %#3x, %pM", dev->name, model_name, - ioaddr, dev->dev_addr); + netdev_info(dev, "%s at %#3x, %pM", model_name, + ioaddr, dev->dev_addr); /* Switch from the station address to the alternate register set and read the useful registers there. */ @@ -265,7 +267,7 @@ static int __init ultra_probe1(struct net_device *dev, int ioaddr) irq = irqmap[((irqreg & 0x40) >> 4) + ((irqreg & 0x0c) >> 2)]; if (irq == 0) { - printk(", failed to detect IRQ line.\n"); + pr_cont(", failed to detect IRQ line.\n"); retval = -EAGAIN; goto out; } @@ -296,7 +298,7 @@ static int __init ultra_probe1(struct net_device *dev, int ioaddr) ei_status.mem = ioremap(dev->mem_start, (ei_status.stop_page - START_PG)*256); if (!ei_status.mem) { - printk(", failed to ioremap.\n"); + pr_cont(", failed to ioremap.\n"); retval = -ENOMEM; goto out; } @@ -304,14 +306,15 @@ static int __init ultra_probe1(struct net_device *dev, int ioaddr) dev->mem_end = dev->mem_start + (ei_status.stop_page - START_PG)*256; if (piomode) { - printk(",%s IRQ %d programmed-I/O mode.\n", - eeprom_irq ? "EEPROM" : "assigned ", dev->irq); + pr_cont(", %s IRQ %d programmed-I/O mode.\n", + eeprom_irq ? "EEPROM" : "assigned ", dev->irq); ei_status.block_input = &ultra_pio_input; ei_status.block_output = &ultra_pio_output; ei_status.get_8390_hdr = &ultra_pio_get_hdr; } else { - printk(",%s IRQ %d memory %#lx-%#lx.\n", eeprom_irq ? "" : "assigned ", - dev->irq, dev->mem_start, dev->mem_end-1); + pr_cont(", %s IRQ %d memory %#lx-%#lx.\n", + eeprom_irq ? "" : "assigned ", dev->irq, dev->mem_start, + dev->mem_end-1); ei_status.block_input = &ultra_block_input; ei_status.block_output = &ultra_block_output; ei_status.get_8390_hdr = &ultra_get_8390_hdr; @@ -320,6 +323,7 @@ static int __init ultra_probe1(struct net_device *dev, int ioaddr) dev->netdev_ops = &ultra_netdev_ops; NS8390_init(dev, 0); + ei_local->msg_enable = ultra_msg_enable; retval = register_netdev(dev); if (retval) @@ -356,12 +360,15 @@ static int __init ultra_probe_isapnp(struct net_device *dev) /* found it */ dev->base_addr = pnp_port_start(idev, 0); dev->irq = pnp_irq(idev, 0); - printk(KERN_INFO "smc-ultra.c: ISAPnP reports %s at i/o %#lx, irq %d.\n", - (char *) ultra_device_ids[i].driver_data, - dev->base_addr, dev->irq); + netdev_info(dev, + "smc-ultra.c: ISAPnP reports %s at i/o %#lx, irq %d.\n", + (char *) ultra_device_ids[i].driver_data, + dev->base_addr, dev->irq); if (ultra_probe1(dev, dev->base_addr) != 0) { /* Shouldn't happen. */ - printk(KERN_ERR "smc-ultra.c: Probe of ISAPnP card at %#lx failed.\n", dev->base_addr); - pnp_device_detach(idev); + netdev_err(dev, + "smc-ultra.c: Probe of ISAPnP card at %#lx failed.\n", + dev->base_addr); + pnp_device_detach(idev); return -ENXIO; } ei_status.priv = (unsigned long)idev; @@ -412,9 +419,10 @@ static void ultra_reset_8390(struct net_device *dev) { int cmd_port = dev->base_addr - ULTRA_NIC_OFFSET; /* ASIC base addr */ + struct ei_device *ei_local = netdev_priv(dev); outb(ULTRA_RESET, cmd_port); - if (ei_debug > 1) printk("resetting Ultra, t=%ld...", jiffies); + netif_dbg(ei_local, hw, dev, "resetting Ultra, t=%ld...\n", jiffies); ei_status.txing = 0; outb(0x00, cmd_port); /* Disable shared memory for safety. */ @@ -424,7 +432,7 @@ ultra_reset_8390(struct net_device *dev) else outb(0x01, cmd_port + 6); /* Enable interrupts and memory. */ - if (ei_debug > 1) printk("reset done\n"); + netif_dbg(ei_local, hw, dev, "reset done\n"); } /* Grab the 8390 specific header. Similar to the block_input routine, but @@ -530,11 +538,11 @@ static int ultra_close_card(struct net_device *dev) { int ioaddr = dev->base_addr - ULTRA_NIC_OFFSET; /* CMDREG */ + struct ei_device *ei_local = netdev_priv(dev); netif_stop_queue(dev); - if (ei_debug > 1) - printk("%s: Shutting down ethercard.\n", dev->name); + netif_dbg(ei_local, ifdown, dev, "Shutting down ethercard.\n"); outb(0x00, ioaddr + 6); /* Disable interrupts. */ free_irq(dev->irq, dev); @@ -556,8 +564,10 @@ static int irq[MAX_ULTRA_CARDS]; module_param_array(io, int, NULL, 0); module_param_array(irq, int, NULL, 0); +module_param_named(msg_enable, ultra_msg_enable, uint, (S_IRUSR|S_IRGRP|S_IROTH)); MODULE_PARM_DESC(io, "I/O base address(es)"); MODULE_PARM_DESC(irq, "IRQ number(s) (assigned)"); +MODULE_PARM_DESC(msg_enable, "Debug message level (see linux/netdevice.h for bitmap)"); MODULE_DESCRIPTION("SMC Ultra/EtherEZ ISA/PnP Ethernet driver"); MODULE_LICENSE("GPL"); diff --git a/drivers/net/ethernet/8390/stnic.c b/drivers/net/ethernet/8390/stnic.c index 8df4c415723..aca957d4e12 100644 --- a/drivers/net/ethernet/8390/stnic.c +++ b/drivers/net/ethernet/8390/stnic.c @@ -69,6 +69,11 @@ static void stnic_block_output (struct net_device *dev, int count, static void stnic_init (struct net_device *dev); +static u32 stnic_msg_enable; + +module_param_named(msg_enable, stnic_msg_enable, uint, (S_IRUSR|S_IRGRP|S_IROTH)); +MODULE_PARM_DESC(msg_enable, "Debug message level (see linux/netdevice.h for bitmap)"); + /* SH7750 specific read/write io. */ static inline void STNIC_DELAY (void) @@ -100,6 +105,7 @@ static int __init stnic_probe(void) { struct net_device *dev; int i, err; + struct ei_device *ei_local; /* If we are not running on a SolutionEngine, give up now */ if (! MACH_SE) @@ -125,10 +131,10 @@ static int __init stnic_probe(void) share and the board will usually be enabled. */ err = request_irq (dev->irq, ei_interrupt, 0, DRV_NAME, dev); if (err) { - printk (KERN_EMERG " unable to get IRQ %d.\n", dev->irq); - free_netdev(dev); - return err; - } + netdev_emerg(dev, " unable to get IRQ %d.\n", dev->irq); + free_netdev(dev); + return err; + } ei_status.name = dev->name; ei_status.word16 = 1; @@ -147,6 +153,8 @@ static int __init stnic_probe(void) ei_status.block_output = &stnic_block_output; stnic_init (dev); + ei_local = netdev_priv(dev); + ei_local->msg_enable = stnic_msg_enable; err = register_netdev(dev); if (err) { @@ -156,7 +164,7 @@ static int __init stnic_probe(void) } stnic_dev = dev; - printk (KERN_INFO "NS ST-NIC 83902A\n"); + netdev_info(dev, "NS ST-NIC 83902A\n"); return 0; } @@ -164,10 +172,11 @@ static int __init stnic_probe(void) static void stnic_reset (struct net_device *dev) { + struct ei_device *ei_local = netdev_priv(dev); + *(vhalf *) PA_83902_RST = 0; udelay (5); - if (ei_debug > 1) - printk (KERN_WARNING "8390 reset done (%ld).\n", jiffies); + netif_warn(ei_local, hw, dev, "8390 reset done (%ld).\n", jiffies); *(vhalf *) PA_83902_RST = ~0; udelay (5); } @@ -176,6 +185,8 @@ static void stnic_get_hdr (struct net_device *dev, struct e8390_pkt_hdr *hdr, int ring_page) { + struct ei_device *ei_local = netdev_priv(dev); + half buf[2]; STNIC_WRITE (PG0_RSAR0, 0); @@ -196,8 +207,7 @@ stnic_get_hdr (struct net_device *dev, struct e8390_pkt_hdr *hdr, hdr->count = ((buf[1] >> 8) & 0xff) | (buf[1] << 8); #endif - if (ei_debug > 1) - printk (KERN_DEBUG "ring %x status %02x next %02x count %04x.\n", + netif_dbg(ei_local, probe, dev, "ring %x status %02x next %02x count %04x.\n", ring_page, hdr->status, hdr->next, hdr->count); STNIC_WRITE (STNIC_CR, CR_RDMA | CR_PG0 | CR_STA); diff --git a/drivers/net/ethernet/8390/wd.c b/drivers/net/ethernet/8390/wd.c index 03eb3eed49f..dd7d816bde5 100644 --- a/drivers/net/ethernet/8390/wd.c +++ b/drivers/net/ethernet/8390/wd.c @@ -60,6 +60,7 @@ static void wd_block_output(struct net_device *dev, int count, const unsigned char *buf, int start_page); static int wd_close(struct net_device *dev); +static u32 wd_msg_enable; #define WD_START_PG 0x00 /* First page of TX buffer */ #define WD03_STOP_PG 0x20 /* Last page +1 of RX ring */ @@ -170,6 +171,7 @@ static int __init wd_probe1(struct net_device *dev, int ioaddr) int word16 = 0; /* 0 = 8 bit, 1 = 16 bit */ const char *model_name; static unsigned version_printed; + struct ei_device *ei_local = netdev_priv(dev); for (i = 0; i < 8; i++) checksum += inb(ioaddr + 8 + i); @@ -180,19 +182,19 @@ static int __init wd_probe1(struct net_device *dev, int ioaddr) /* Check for semi-valid mem_start/end values if supplied. */ if ((dev->mem_start % 0x2000) || (dev->mem_end % 0x2000)) { - printk(KERN_WARNING "wd.c: user supplied mem_start or mem_end not on 8kB boundary - ignored.\n"); + netdev_warn(dev, + "wd.c: user supplied mem_start or mem_end not on 8kB boundary - ignored.\n"); dev->mem_start = 0; dev->mem_end = 0; } - if (ei_debug && version_printed++ == 0) - printk(version); + if ((wd_msg_enable & NETIF_MSG_DRV) && (version_printed++ == 0)) + netdev_info(dev, version); for (i = 0; i < 6; i++) dev->dev_addr[i] = inb(ioaddr + 8 + i); - printk("%s: WD80x3 at %#3x, %pM", - dev->name, ioaddr, dev->dev_addr); + netdev_info(dev, "WD80x3 at %#3x, %pM", ioaddr, dev->dev_addr); /* The following PureData probe code was contributed by Mike Jagdis <jaggy@purplet.demon.co.uk>. Puredata does software @@ -244,8 +246,9 @@ static int __init wd_probe1(struct net_device *dev, int ioaddr) } #ifndef final_version if ( !ancient && (inb(ioaddr+1) & 0x01) != (word16 & 0x01)) - printk("\nWD80?3: Bus width conflict, %d (probe) != %d (reg report).", - word16 ? 16 : 8, (inb(ioaddr+1) & 0x01) ? 16 : 8); + pr_cont("\nWD80?3: Bus width conflict, %d (probe) != %d (reg report).", + word16 ? 16 : 8, + (inb(ioaddr+1) & 0x01) ? 16 : 8); #endif } @@ -259,7 +262,7 @@ static int __init wd_probe1(struct net_device *dev, int ioaddr) if (reg0 == 0xff || reg0 == 0) { /* Future plan: this could check a few likely locations first. */ dev->mem_start = 0xd0000; - printk(" assigning address %#lx", dev->mem_start); + pr_cont(" assigning address %#lx", dev->mem_start); } else { int high_addr_bits = inb(ioaddr+WD_CMDREG5) & 0x1f; /* Some boards don't have the register 5 -- it returns 0xff. */ @@ -297,8 +300,8 @@ static int __init wd_probe1(struct net_device *dev, int ioaddr) outb_p(0x00, nic_addr+EN0_IMR); /* Mask all intrs. again. */ - if (ei_debug > 2) - printk(" autoirq is %d", dev->irq); + if (netif_msg_drv(ei_local)) + pr_cont(" autoirq is %d", dev->irq); if (dev->irq < 2) dev->irq = word16 ? 10 : 5; } else @@ -310,7 +313,7 @@ static int __init wd_probe1(struct net_device *dev, int ioaddr) share and the board will usually be enabled. */ i = request_irq(dev->irq, ei_interrupt, 0, DRV_NAME, dev); if (i) { - printk (" unable to get IRQ %d.\n", dev->irq); + pr_cont(" unable to get IRQ %d.\n", dev->irq); return i; } @@ -338,8 +341,8 @@ static int __init wd_probe1(struct net_device *dev, int ioaddr) return -ENOMEM; } - printk(" %s, IRQ %d, shared memory at %#lx-%#lx.\n", - model_name, dev->irq, dev->mem_start, dev->mem_end-1); + pr_cont(" %s, IRQ %d, shared memory at %#lx-%#lx.\n", + model_name, dev->irq, dev->mem_start, dev->mem_end-1); ei_status.reset_8390 = wd_reset_8390; ei_status.block_input = wd_block_input; @@ -348,6 +351,7 @@ static int __init wd_probe1(struct net_device *dev, int ioaddr) dev->netdev_ops = &wd_netdev_ops; NS8390_init(dev, 0); + ei_local->msg_enable = wd_msg_enable; #if 1 /* Enable interrupt generation on softconfig cards -- M.U */ @@ -385,9 +389,11 @@ static void wd_reset_8390(struct net_device *dev) { int wd_cmd_port = dev->base_addr - WD_NIC_OFFSET; /* WD_CMDREG */ + struct ei_device *ei_local = netdev_priv(dev); outb(WD_RESET, wd_cmd_port); - if (ei_debug > 1) printk("resetting the WD80x3 t=%lu...", jiffies); + netif_dbg(ei_local, hw, dev, "resetting the WD80x3 t=%lu...\n", + jiffies); ei_status.txing = 0; /* Set up the ASIC registers, just in case something changed them. */ @@ -395,7 +401,7 @@ wd_reset_8390(struct net_device *dev) if (ei_status.word16) outb(NIC16 | ((dev->mem_start>>19) & 0x1f), wd_cmd_port+WD_CMDREG5); - if (ei_debug > 1) printk("reset done\n"); + netif_dbg(ei_local, hw, dev, "reset done\n"); } /* Grab the 8390 specific header. Similar to the block_input routine, but @@ -474,9 +480,9 @@ static int wd_close(struct net_device *dev) { int wd_cmdreg = dev->base_addr - WD_NIC_OFFSET; /* WD_CMDREG */ + struct ei_device *ei_local = netdev_priv(dev); - if (ei_debug > 1) - printk("%s: Shutting down ethercard.\n", dev->name); + netif_dbg(ei_local, ifdown, dev, "Shutting down ethercard.\n"); ei_close(dev); /* Change from 16-bit to 8-bit shared memory so reboot works. */ @@ -502,10 +508,12 @@ module_param_array(io, int, NULL, 0); module_param_array(irq, int, NULL, 0); module_param_array(mem, int, NULL, 0); module_param_array(mem_end, int, NULL, 0); +module_param_named(msg_enable, wd_msg_enable, uint, (S_IRUSR|S_IRGRP|S_IROTH)); MODULE_PARM_DESC(io, "I/O base address(es)"); MODULE_PARM_DESC(irq, "IRQ number(s) (ignored for PureData boards)"); MODULE_PARM_DESC(mem, "memory base address(es)(ignored for PureData boards)"); MODULE_PARM_DESC(mem_end, "memory end address(es)"); +MODULE_PARM_DESC(msg_enable, "Debug message level (see linux/netdevice.h for bitmap)"); MODULE_DESCRIPTION("ISA Western Digital wd8003/wd8013 ; SMC Elite, Elite16 ethernet driver"); MODULE_LICENSE("GPL"); diff --git a/drivers/net/ethernet/8390/zorro8390.c b/drivers/net/ethernet/8390/zorro8390.c index 85ec4c2d264..8308728fad0 100644 --- a/drivers/net/ethernet/8390/zorro8390.c +++ b/drivers/net/ethernet/8390/zorro8390.c @@ -44,6 +44,8 @@ static const char version[] = "8390.c:v1.10cvs 9/23/94 Donald Becker (becker@cesdis.gsfc.nasa.gov)\n"; +static u32 zorro8390_msg_enable; + #include "lib8390.c" #define DRV_NAME "zorro8390" @@ -86,9 +88,9 @@ static struct card_info { static void zorro8390_reset_8390(struct net_device *dev) { unsigned long reset_start_time = jiffies; + struct ei_device *ei_local = netdev_priv(dev); - if (ei_debug > 1) - netdev_dbg(dev, "resetting - t=%ld...\n", jiffies); + netif_dbg(ei_local, hw, dev, "resetting - t=%ld...\n", jiffies); z_writeb(z_readb(NE_BASE + NE_RESET), NE_BASE + NE_RESET); @@ -119,8 +121,9 @@ static void zorro8390_get_8390_hdr(struct net_device *dev, * If it does, it's the last thing you'll see */ if (ei_status.dmaing) { - netdev_err(dev, "%s: DMAing conflict [DMAstat:%d][irqlock:%d]\n", - __func__, ei_status.dmaing, ei_status.irqlock); + netdev_warn(dev, + "%s: DMAing conflict [DMAstat:%d][irqlock:%d]\n", + __func__, ei_status.dmaing, ei_status.irqlock); return; } @@ -230,7 +233,7 @@ static void zorro8390_block_output(struct net_device *dev, int count, while ((z_readb(NE_BASE + NE_EN0_ISR) & ENISR_RDC) == 0) if (time_after(jiffies, dma_start + 2 * HZ / 100)) { /* 20ms */ - netdev_err(dev, "timeout waiting for Tx RDC\n"); + netdev_warn(dev, "timeout waiting for Tx RDC\n"); zorro8390_reset_8390(dev); __NS8390_init(dev, 1); break; @@ -248,8 +251,9 @@ static int zorro8390_open(struct net_device *dev) static int zorro8390_close(struct net_device *dev) { - if (ei_debug > 1) - netdev_dbg(dev, "Shutting down ethercard\n"); + struct ei_device *ei_local = netdev_priv(dev); + + netif_dbg(ei_local, ifdown, dev, "Shutting down ethercard\n"); __ei_close(dev); return 0; } @@ -287,12 +291,13 @@ static const struct net_device_ops zorro8390_netdev_ops = { }; static int zorro8390_init(struct net_device *dev, unsigned long board, - const char *name, unsigned long ioaddr) + const char *name, void __iomem *ioaddr) { int i; int err; unsigned char SA_prom[32]; int start_page, stop_page; + struct ei_device *ei_local = netdev_priv(dev); static u32 zorro8390_offsets[16] = { 0x00, 0x02, 0x04, 0x06, 0x08, 0x0a, 0x0c, 0x0e, 0x10, 0x12, 0x14, 0x16, 0x18, 0x1a, 0x1c, 0x1e, @@ -354,7 +359,7 @@ static int zorro8390_init(struct net_device *dev, unsigned long board, start_page = NESM_START_PG; stop_page = NESM_STOP_PG; - dev->base_addr = ioaddr; + dev->base_addr = (unsigned long)ioaddr; dev->irq = IRQ_AMIGA_PORTS; /* Install the Interrupt handler */ @@ -383,6 +388,9 @@ static int zorro8390_init(struct net_device *dev, unsigned long board, dev->netdev_ops = &zorro8390_netdev_ops; __NS8390_init(dev, 0); + + ei_local->msg_enable = zorro8390_msg_enable; + err = register_netdev(dev); if (err) { free_irq(IRQ_AMIGA_PORTS, dev); |