diff options
Diffstat (limited to 'drivers/net/can')
53 files changed, 4816 insertions, 1407 deletions
diff --git a/drivers/net/can/Kconfig b/drivers/net/can/Kconfig index 3c069472eb8..41688229c57 100644 --- a/drivers/net/can/Kconfig +++ b/drivers/net/can/Kconfig @@ -65,24 +65,18 @@ config CAN_LEDS config CAN_AT91 tristate "Atmel AT91 onchip CAN controller" - depends on ARM + depends on ARCH_AT91 || COMPILE_TEST ---help--- This is a driver for the SoC CAN controller in Atmel's AT91SAM9263 and AT91SAM9X5 processors. config CAN_TI_HECC - depends on ARCH_OMAP3 + depends on ARM tristate "TI High End CAN Controller" ---help--- Driver for TI HECC (High End CAN Controller) module found on many TI devices. The device specifications are available from www.ti.com -config CAN_MCP251X - tristate "Microchip MCP251x SPI CAN controllers" - depends on SPI && HAS_DMA - ---help--- - Driver for the Microchip MCP251x SPI CAN controllers. - config CAN_BFIN depends on BF534 || BF536 || BF537 || BF538 || BF539 || BF54x tristate "Analog Devices Blackfin on-chip CAN" @@ -110,7 +104,7 @@ config CAN_FLEXCAN config PCH_CAN tristate "Intel EG20T PCH CAN controller" - depends on PCI + depends on PCI && (X86_32 || COMPILE_TEST) ---help--- This driver is for PCH CAN of Topcliff (Intel EG20T PCH) which is an IOH for x86 embedded processor (Intel Atom E6xx series). @@ -125,6 +119,24 @@ config CAN_GRCAN endian syntheses of the cores would need some modifications on the hardware level to work. +config CAN_RCAR + tristate "Renesas R-Car CAN controller" + depends on ARM + ---help--- + Say Y here if you want to use CAN controller found on Renesas R-Car + SoCs. + + To compile this driver as a module, choose M here: the module will + be called rcar_can. + +config CAN_XILINXCAN + tristate "Xilinx CAN" + depends on ARCH_ZYNQ || MICROBLAZE || COMPILE_TEST + depends on COMMON_CLK && HAS_IOMEM + ---help--- + Xilinx CAN driver. This driver supports both soft AXI CAN IP and + Zynq CANPS IP. + source "drivers/net/can/mscan/Kconfig" source "drivers/net/can/sja1000/Kconfig" @@ -133,6 +145,8 @@ source "drivers/net/can/c_can/Kconfig" source "drivers/net/can/cc770/Kconfig" +source "drivers/net/can/spi/Kconfig" + source "drivers/net/can/usb/Kconfig" source "drivers/net/can/softing/Kconfig" diff --git a/drivers/net/can/Makefile b/drivers/net/can/Makefile index c7440392adb..1697f22353a 100644 --- a/drivers/net/can/Makefile +++ b/drivers/net/can/Makefile @@ -10,6 +10,7 @@ can-dev-y := dev.o can-dev-$(CONFIG_CAN_LEDS) += led.o +obj-y += spi/ obj-y += usb/ obj-y += softing/ @@ -19,11 +20,12 @@ obj-$(CONFIG_CAN_C_CAN) += c_can/ obj-$(CONFIG_CAN_CC770) += cc770/ obj-$(CONFIG_CAN_AT91) += at91_can.o obj-$(CONFIG_CAN_TI_HECC) += ti_hecc.o -obj-$(CONFIG_CAN_MCP251X) += mcp251x.o obj-$(CONFIG_CAN_BFIN) += bfin_can.o obj-$(CONFIG_CAN_JANZ_ICAN3) += janz-ican3.o obj-$(CONFIG_CAN_FLEXCAN) += flexcan.o obj-$(CONFIG_PCH_CAN) += pch_can.o obj-$(CONFIG_CAN_GRCAN) += grcan.o +obj-$(CONFIG_CAN_RCAR) += rcar_can.o +obj-$(CONFIG_CAN_XILINXCAN) += xilinx_can.o ccflags-$(CONFIG_CAN_DEBUG_DEVICES) := -DDEBUG diff --git a/drivers/net/can/at91_can.c b/drivers/net/can/at91_can.c index 3b1ff614870..f07fa89b5fd 100644 --- a/drivers/net/can/at91_can.c +++ b/drivers/net/can/at91_can.c @@ -22,7 +22,6 @@ #include <linux/clk.h> #include <linux/errno.h> #include <linux/if_arp.h> -#include <linux/init.h> #include <linux/interrupt.h> #include <linux/kernel.h> #include <linux/module.h> @@ -421,7 +420,11 @@ static void at91_chip_start(struct net_device *dev) at91_transceiver_switch(priv, 1); /* enable chip */ - at91_write(priv, AT91_MR, AT91_MR_CANEN); + if (priv->can.ctrlmode & CAN_CTRLMODE_LISTENONLY) + reg_mr = AT91_MR_CANEN | AT91_MR_ABM; + else + reg_mr = AT91_MR_CANEN; + at91_write(priv, AT91_MR, reg_mr); priv->can.state = CAN_STATE_ERROR_ACTIVE; @@ -1191,6 +1194,7 @@ static const struct net_device_ops at91_netdev_ops = { .ndo_open = at91_open, .ndo_stop = at91_close, .ndo_start_xmit = at91_start_xmit, + .ndo_change_mtu = can_change_mtu, }; static ssize_t at91_sysfs_show_mb0_id(struct device *dev, @@ -1342,12 +1346,13 @@ static int at91_can_probe(struct platform_device *pdev) priv->can.bittiming_const = &at91_bittiming_const; priv->can.do_set_mode = at91_set_mode; priv->can.do_get_berr_counter = at91_get_berr_counter; - priv->can.ctrlmode_supported = CAN_CTRLMODE_3_SAMPLES; + priv->can.ctrlmode_supported = CAN_CTRLMODE_3_SAMPLES | + CAN_CTRLMODE_LISTENONLY; priv->dev = dev; priv->reg_base = addr; priv->devtype_data = *devtype_data; priv->clk = clk; - priv->pdata = pdev->dev.platform_data; + priv->pdata = dev_get_platdata(&pdev->dev); priv->mb0_id = 0x7ff; netif_napi_add(dev, &priv->napi, at91_poll, get_mb_rx_num(priv)); @@ -1405,10 +1410,10 @@ static int at91_can_remove(struct platform_device *pdev) static const struct platform_device_id at91_can_id_table[] = { { - .name = "at91_can", + .name = "at91sam9x5_can", .driver_data = (kernel_ulong_t)&at91_at91sam9x5_data, }, { - .name = "at91sam9x5_can", + .name = "at91_can", .driver_data = (kernel_ulong_t)&at91_at91sam9263_data, }, { /* sentinel */ diff --git a/drivers/net/can/bfin_can.c b/drivers/net/can/bfin_can.c index a2700d25ff0..543ecceb33e 100644 --- a/drivers/net/can/bfin_can.c +++ b/drivers/net/can/bfin_can.c @@ -9,7 +9,6 @@ */ #include <linux/module.h> -#include <linux/init.h> #include <linux/kernel.h> #include <linux/bitops.h> #include <linux/interrupt.h> @@ -529,6 +528,7 @@ static const struct net_device_ops bfin_can_netdev_ops = { .ndo_open = bfin_can_open, .ndo_stop = bfin_can_close, .ndo_start_xmit = bfin_can_start_xmit, + .ndo_change_mtu = can_change_mtu, }; static int bfin_can_probe(struct platform_device *pdev) @@ -539,7 +539,7 @@ static int bfin_can_probe(struct platform_device *pdev) struct resource *res_mem, *rx_irq, *tx_irq, *err_irq; unsigned short *pdata; - pdata = pdev->dev.platform_data; + pdata = dev_get_platdata(&pdev->dev); if (!pdata) { dev_err(&pdev->dev, "No platform data provided!\n"); err = -EINVAL; diff --git a/drivers/net/can/c_can/c_can.c b/drivers/net/can/c_can/c_can.c index a668cd491cb..8e78bb48f5a 100644 --- a/drivers/net/can/c_can/c_can.c +++ b/drivers/net/can/c_can/c_can.c @@ -60,6 +60,8 @@ #define CONTROL_IE BIT(1) #define CONTROL_INIT BIT(0) +#define CONTROL_IRQMSK (CONTROL_EIE | CONTROL_IE | CONTROL_SIE) + /* test register */ #define TEST_RX BIT(7) #define TEST_TX1 BIT(6) @@ -108,21 +110,38 @@ #define IF_COMM_CONTROL BIT(4) #define IF_COMM_CLR_INT_PND BIT(3) #define IF_COMM_TXRQST BIT(2) +#define IF_COMM_CLR_NEWDAT IF_COMM_TXRQST #define IF_COMM_DATAA BIT(1) #define IF_COMM_DATAB BIT(0) -#define IF_COMM_ALL (IF_COMM_MASK | IF_COMM_ARB | \ - IF_COMM_CONTROL | IF_COMM_TXRQST | \ - IF_COMM_DATAA | IF_COMM_DATAB) + +/* TX buffer setup */ +#define IF_COMM_TX (IF_COMM_ARB | IF_COMM_CONTROL | \ + IF_COMM_TXRQST | \ + IF_COMM_DATAA | IF_COMM_DATAB) + +/* For the low buffers we clear the interrupt bit, but keep newdat */ +#define IF_COMM_RCV_LOW (IF_COMM_MASK | IF_COMM_ARB | \ + IF_COMM_CONTROL | IF_COMM_CLR_INT_PND | \ + IF_COMM_DATAA | IF_COMM_DATAB) + +/* For the high buffers we clear the interrupt bit and newdat */ +#define IF_COMM_RCV_HIGH (IF_COMM_RCV_LOW | IF_COMM_CLR_NEWDAT) + + +/* Receive setup of message objects */ +#define IF_COMM_RCV_SETUP (IF_COMM_MASK | IF_COMM_ARB | IF_COMM_CONTROL) + +/* Invalidation of message objects */ +#define IF_COMM_INVAL (IF_COMM_ARB | IF_COMM_CONTROL) /* IFx arbitration */ -#define IF_ARB_MSGVAL BIT(15) -#define IF_ARB_MSGXTD BIT(14) -#define IF_ARB_TRANSMIT BIT(13) +#define IF_ARB_MSGVAL BIT(31) +#define IF_ARB_MSGXTD BIT(30) +#define IF_ARB_TRANSMIT BIT(29) /* IFx message control */ #define IF_MCONT_NEWDAT BIT(15) #define IF_MCONT_MSGLST BIT(14) -#define IF_MCONT_CLR_MSGLST (0 << 14) #define IF_MCONT_INTPND BIT(13) #define IF_MCONT_UMASK BIT(12) #define IF_MCONT_TXIE BIT(11) @@ -132,39 +151,16 @@ #define IF_MCONT_EOB BIT(7) #define IF_MCONT_DLC_MASK 0xf -/* - * IFx register masks: - * allow easy operation on 16-bit registers when the - * argument is 32-bit instead - */ -#define IFX_WRITE_LOW_16BIT(x) ((x) & 0xFFFF) -#define IFX_WRITE_HIGH_16BIT(x) (((x) & 0xFFFF0000) >> 16) - -/* message object split */ -#define C_CAN_NO_OF_OBJECTS 32 -#define C_CAN_MSG_OBJ_RX_NUM 16 -#define C_CAN_MSG_OBJ_TX_NUM 16 - -#define C_CAN_MSG_OBJ_RX_FIRST 1 -#define C_CAN_MSG_OBJ_RX_LAST (C_CAN_MSG_OBJ_RX_FIRST + \ - C_CAN_MSG_OBJ_RX_NUM - 1) - -#define C_CAN_MSG_OBJ_TX_FIRST (C_CAN_MSG_OBJ_RX_LAST + 1) -#define C_CAN_MSG_OBJ_TX_LAST (C_CAN_MSG_OBJ_TX_FIRST + \ - C_CAN_MSG_OBJ_TX_NUM - 1) - -#define C_CAN_MSG_OBJ_RX_SPLIT 9 -#define C_CAN_MSG_RX_LOW_LAST (C_CAN_MSG_OBJ_RX_SPLIT - 1) - -#define C_CAN_NEXT_MSG_OBJ_MASK (C_CAN_MSG_OBJ_TX_NUM - 1) -#define RECEIVE_OBJECT_BITS 0x0000ffff +#define IF_MCONT_RCV (IF_MCONT_RXIE | IF_MCONT_UMASK) +#define IF_MCONT_RCV_EOB (IF_MCONT_RCV | IF_MCONT_EOB) -/* status interrupt */ -#define STATUS_INTERRUPT 0x8000 +#define IF_MCONT_TX (IF_MCONT_TXIE | IF_MCONT_EOB) -/* global interrupt masks */ -#define ENABLE_ALL_INTERRUPTS 1 -#define DISABLE_ALL_INTERRUPTS 0 +/* + * Use IF1 for RX and IF2 for TX + */ +#define IF_RX 0 +#define IF_TX 1 /* minimum timeout for checking BUSY status */ #define MIN_TIMEOUT_VALUE 6 @@ -185,6 +181,7 @@ enum c_can_lec_type { LEC_BIT0_ERROR, LEC_CRC_ERROR, LEC_UNUSED, + LEC_MASK = LEC_UNUSED, }; /* @@ -240,210 +237,149 @@ static inline void c_can_reset_ram(const struct c_can_priv *priv, bool enable) priv->raminit(priv, enable); } -static inline int get_tx_next_msg_obj(const struct c_can_priv *priv) -{ - return (priv->tx_next & C_CAN_NEXT_MSG_OBJ_MASK) + - C_CAN_MSG_OBJ_TX_FIRST; -} - -static inline int get_tx_echo_msg_obj(const struct c_can_priv *priv) +static void c_can_irq_control(struct c_can_priv *priv, bool enable) { - return (priv->tx_echo & C_CAN_NEXT_MSG_OBJ_MASK) + - C_CAN_MSG_OBJ_TX_FIRST; -} - -static u32 c_can_read_reg32(struct c_can_priv *priv, enum reg index) -{ - u32 val = priv->read_reg(priv, index); - val |= ((u32) priv->read_reg(priv, index + 1)) << 16; - return val; -} - -static void c_can_enable_all_interrupts(struct c_can_priv *priv, - int enable) -{ - unsigned int cntrl_save = priv->read_reg(priv, - C_CAN_CTRL_REG); + u32 ctrl = priv->read_reg(priv, C_CAN_CTRL_REG) & ~CONTROL_IRQMSK; if (enable) - cntrl_save |= (CONTROL_SIE | CONTROL_EIE | CONTROL_IE); - else - cntrl_save &= ~(CONTROL_EIE | CONTROL_IE | CONTROL_SIE); + ctrl |= CONTROL_IRQMSK; - priv->write_reg(priv, C_CAN_CTRL_REG, cntrl_save); + priv->write_reg(priv, C_CAN_CTRL_REG, ctrl); } -static inline int c_can_msg_obj_is_busy(struct c_can_priv *priv, int iface) +static void c_can_obj_update(struct net_device *dev, int iface, u32 cmd, u32 obj) { - int count = MIN_TIMEOUT_VALUE; + struct c_can_priv *priv = netdev_priv(dev); + int cnt, reg = C_CAN_IFACE(COMREQ_REG, iface); - while (count && priv->read_reg(priv, - C_CAN_IFACE(COMREQ_REG, iface)) & - IF_COMR_BUSY) { - count--; + priv->write_reg32(priv, reg, (cmd << 16) | obj); + + for (cnt = MIN_TIMEOUT_VALUE; cnt; cnt--) { + if (!(priv->read_reg(priv, reg) & IF_COMR_BUSY)) + return; udelay(1); } + netdev_err(dev, "Updating object timed out\n"); - if (!count) - return 1; +} - return 0; +static inline void c_can_object_get(struct net_device *dev, int iface, + u32 obj, u32 cmd) +{ + c_can_obj_update(dev, iface, cmd, obj); } -static inline void c_can_object_get(struct net_device *dev, - int iface, int objno, int mask) +static inline void c_can_object_put(struct net_device *dev, int iface, + u32 obj, u32 cmd) { - struct c_can_priv *priv = netdev_priv(dev); + c_can_obj_update(dev, iface, cmd | IF_COMM_WR, obj); +} - /* - * As per specs, after writting the message object number in the - * IF command request register the transfer b/w interface - * register and message RAM must be complete in 6 CAN-CLK - * period. - */ - priv->write_reg(priv, C_CAN_IFACE(COMMSK_REG, iface), - IFX_WRITE_LOW_16BIT(mask)); - priv->write_reg(priv, C_CAN_IFACE(COMREQ_REG, iface), - IFX_WRITE_LOW_16BIT(objno)); +/* + * Note: According to documentation clearing TXIE while MSGVAL is set + * is not allowed, but works nicely on C/DCAN. And that lowers the I/O + * load significantly. + */ +static void c_can_inval_tx_object(struct net_device *dev, int iface, int obj) +{ + struct c_can_priv *priv = netdev_priv(dev); - if (c_can_msg_obj_is_busy(priv, iface)) - netdev_err(dev, "timed out in object get\n"); + priv->write_reg(priv, C_CAN_IFACE(MSGCTRL_REG, iface), 0); + c_can_object_put(dev, iface, obj, IF_COMM_INVAL); } -static inline void c_can_object_put(struct net_device *dev, - int iface, int objno, int mask) +static void c_can_inval_msg_object(struct net_device *dev, int iface, int obj) { struct c_can_priv *priv = netdev_priv(dev); - /* - * As per specs, after writting the message object number in the - * IF command request register the transfer b/w interface - * register and message RAM must be complete in 6 CAN-CLK - * period. - */ - priv->write_reg(priv, C_CAN_IFACE(COMMSK_REG, iface), - (IF_COMM_WR | IFX_WRITE_LOW_16BIT(mask))); - priv->write_reg(priv, C_CAN_IFACE(COMREQ_REG, iface), - IFX_WRITE_LOW_16BIT(objno)); - - if (c_can_msg_obj_is_busy(priv, iface)) - netdev_err(dev, "timed out in object put\n"); + priv->write_reg(priv, C_CAN_IFACE(ARB1_REG, iface), 0); + priv->write_reg(priv, C_CAN_IFACE(ARB2_REG, iface), 0); + c_can_inval_tx_object(dev, iface, obj); } -static void c_can_write_msg_object(struct net_device *dev, - int iface, struct can_frame *frame, int objno) +static void c_can_setup_tx_object(struct net_device *dev, int iface, + struct can_frame *frame, int idx) { - int i; - u16 flags = 0; - unsigned int id; struct c_can_priv *priv = netdev_priv(dev); - - if (!(frame->can_id & CAN_RTR_FLAG)) - flags |= IF_ARB_TRANSMIT; + u16 ctrl = IF_MCONT_TX | frame->can_dlc; + bool rtr = frame->can_id & CAN_RTR_FLAG; + u32 arb = IF_ARB_MSGVAL; + int i; if (frame->can_id & CAN_EFF_FLAG) { - id = frame->can_id & CAN_EFF_MASK; - flags |= IF_ARB_MSGXTD; - } else - id = ((frame->can_id & CAN_SFF_MASK) << 18); + arb |= frame->can_id & CAN_EFF_MASK; + arb |= IF_ARB_MSGXTD; + } else { + arb |= (frame->can_id & CAN_SFF_MASK) << 18; + } - flags |= IF_ARB_MSGVAL; + if (!rtr) + arb |= IF_ARB_TRANSMIT; - priv->write_reg(priv, C_CAN_IFACE(ARB1_REG, iface), - IFX_WRITE_LOW_16BIT(id)); - priv->write_reg(priv, C_CAN_IFACE(ARB2_REG, iface), flags | - IFX_WRITE_HIGH_16BIT(id)); + /* + * If we change the DIR bit, we need to invalidate the buffer + * first, i.e. clear the MSGVAL flag in the arbiter. + */ + if (rtr != (bool)test_bit(idx, &priv->tx_dir)) { + u32 obj = idx + C_CAN_MSG_OBJ_TX_FIRST; - for (i = 0; i < frame->can_dlc; i += 2) { - priv->write_reg(priv, C_CAN_IFACE(DATA1_REG, iface) + i / 2, - frame->data[i] | (frame->data[i + 1] << 8)); + c_can_inval_msg_object(dev, iface, obj); + change_bit(idx, &priv->tx_dir); } - /* enable interrupt for this message object */ - priv->write_reg(priv, C_CAN_IFACE(MSGCTRL_REG, iface), - IF_MCONT_TXIE | IF_MCONT_TXRQST | IF_MCONT_EOB | - frame->can_dlc); - c_can_object_put(dev, iface, objno, IF_COMM_ALL); -} + priv->write_reg32(priv, C_CAN_IFACE(ARB1_REG, iface), arb); -static inline void c_can_mark_rx_msg_obj(struct net_device *dev, - int iface, int ctrl_mask, - int obj) -{ - struct c_can_priv *priv = netdev_priv(dev); - - priv->write_reg(priv, C_CAN_IFACE(MSGCTRL_REG, iface), - ctrl_mask & ~(IF_MCONT_MSGLST | IF_MCONT_INTPND)); - c_can_object_put(dev, iface, obj, IF_COMM_CONTROL); + priv->write_reg(priv, C_CAN_IFACE(MSGCTRL_REG, iface), ctrl); + for (i = 0; i < frame->can_dlc; i += 2) { + priv->write_reg(priv, C_CAN_IFACE(DATA1_REG, iface) + i / 2, + frame->data[i] | (frame->data[i + 1] << 8)); + } } static inline void c_can_activate_all_lower_rx_msg_obj(struct net_device *dev, - int iface, - int ctrl_mask) + int iface) { int i; - struct c_can_priv *priv = netdev_priv(dev); - for (i = C_CAN_MSG_OBJ_RX_FIRST; i <= C_CAN_MSG_RX_LOW_LAST; i++) { - priv->write_reg(priv, C_CAN_IFACE(MSGCTRL_REG, iface), - ctrl_mask & ~(IF_MCONT_MSGLST | - IF_MCONT_INTPND | IF_MCONT_NEWDAT)); - c_can_object_put(dev, iface, i, IF_COMM_CONTROL); - } + for (i = C_CAN_MSG_OBJ_RX_FIRST; i <= C_CAN_MSG_RX_LOW_LAST; i++) + c_can_object_get(dev, iface, i, IF_COMM_CLR_NEWDAT); } -static inline void c_can_activate_rx_msg_obj(struct net_device *dev, - int iface, int ctrl_mask, - int obj) +static int c_can_handle_lost_msg_obj(struct net_device *dev, + int iface, int objno, u32 ctrl) { - struct c_can_priv *priv = netdev_priv(dev); - - priv->write_reg(priv, C_CAN_IFACE(MSGCTRL_REG, iface), - ctrl_mask & ~(IF_MCONT_MSGLST | - IF_MCONT_INTPND | IF_MCONT_NEWDAT)); - c_can_object_put(dev, iface, obj, IF_COMM_CONTROL); -} - -static void c_can_handle_lost_msg_obj(struct net_device *dev, - int iface, int objno) -{ - struct c_can_priv *priv = netdev_priv(dev); struct net_device_stats *stats = &dev->stats; - struct sk_buff *skb; + struct c_can_priv *priv = netdev_priv(dev); struct can_frame *frame; + struct sk_buff *skb; - netdev_err(dev, "msg lost in buffer %d\n", objno); - - c_can_object_get(dev, iface, objno, IF_COMM_ALL & ~IF_COMM_TXRQST); - - priv->write_reg(priv, C_CAN_IFACE(MSGCTRL_REG, iface), - IF_MCONT_CLR_MSGLST); + ctrl &= ~(IF_MCONT_MSGLST | IF_MCONT_INTPND | IF_MCONT_NEWDAT); + priv->write_reg(priv, C_CAN_IFACE(MSGCTRL_REG, iface), ctrl); + c_can_object_put(dev, iface, objno, IF_COMM_CONTROL); - c_can_object_put(dev, 0, objno, IF_COMM_CONTROL); + stats->rx_errors++; + stats->rx_over_errors++; /* create an error msg */ skb = alloc_can_err_skb(dev, &frame); if (unlikely(!skb)) - return; + return 0; frame->can_id |= CAN_ERR_CRTL; frame->data[1] = CAN_ERR_CRTL_RX_OVERFLOW; - stats->rx_errors++; - stats->rx_over_errors++; netif_receive_skb(skb); + return 1; } -static int c_can_read_msg_object(struct net_device *dev, int iface, int ctrl) +static int c_can_read_msg_object(struct net_device *dev, int iface, u32 ctrl) { - u16 flags, data; - int i; - unsigned int val; - struct c_can_priv *priv = netdev_priv(dev); struct net_device_stats *stats = &dev->stats; - struct sk_buff *skb; + struct c_can_priv *priv = netdev_priv(dev); struct can_frame *frame; + struct sk_buff *skb; + u32 arb, data; skb = alloc_can_skb(dev, &frame); if (!skb) { @@ -453,119 +389,98 @@ static int c_can_read_msg_object(struct net_device *dev, int iface, int ctrl) frame->can_dlc = get_can_dlc(ctrl & 0x0F); - flags = priv->read_reg(priv, C_CAN_IFACE(ARB2_REG, iface)); - val = priv->read_reg(priv, C_CAN_IFACE(ARB1_REG, iface)) | - (flags << 16); + arb = priv->read_reg32(priv, C_CAN_IFACE(ARB1_REG, iface)); - if (flags & IF_ARB_MSGXTD) - frame->can_id = (val & CAN_EFF_MASK) | CAN_EFF_FLAG; + if (arb & IF_ARB_MSGXTD) + frame->can_id = (arb & CAN_EFF_MASK) | CAN_EFF_FLAG; else - frame->can_id = (val >> 18) & CAN_SFF_MASK; + frame->can_id = (arb >> 18) & CAN_SFF_MASK; - if (flags & IF_ARB_TRANSMIT) + if (arb & IF_ARB_TRANSMIT) { frame->can_id |= CAN_RTR_FLAG; - else { - for (i = 0; i < frame->can_dlc; i += 2) { - data = priv->read_reg(priv, - C_CAN_IFACE(DATA1_REG, iface) + i / 2); + } else { + int i, dreg = C_CAN_IFACE(DATA1_REG, iface); + + for (i = 0; i < frame->can_dlc; i += 2, dreg ++) { + data = priv->read_reg(priv, dreg); frame->data[i] = data; frame->data[i + 1] = data >> 8; } } - netif_receive_skb(skb); - stats->rx_packets++; stats->rx_bytes += frame->can_dlc; - can_led_event(dev, CAN_LED_EVENT_RX); - + netif_receive_skb(skb); return 0; } static void c_can_setup_receive_object(struct net_device *dev, int iface, - int objno, unsigned int mask, - unsigned int id, unsigned int mcont) + u32 obj, u32 mask, u32 id, u32 mcont) { struct c_can_priv *priv = netdev_priv(dev); - priv->write_reg(priv, C_CAN_IFACE(MASK1_REG, iface), - IFX_WRITE_LOW_16BIT(mask)); - - /* According to C_CAN documentation, the reserved bit - * in IFx_MASK2 register is fixed 1 - */ - priv->write_reg(priv, C_CAN_IFACE(MASK2_REG, iface), - IFX_WRITE_HIGH_16BIT(mask) | BIT(13)); + mask |= BIT(29); + priv->write_reg32(priv, C_CAN_IFACE(MASK1_REG, iface), mask); - priv->write_reg(priv, C_CAN_IFACE(ARB1_REG, iface), - IFX_WRITE_LOW_16BIT(id)); - priv->write_reg(priv, C_CAN_IFACE(ARB2_REG, iface), - (IF_ARB_MSGVAL | IFX_WRITE_HIGH_16BIT(id))); + id |= IF_ARB_MSGVAL; + priv->write_reg32(priv, C_CAN_IFACE(ARB1_REG, iface), id); priv->write_reg(priv, C_CAN_IFACE(MSGCTRL_REG, iface), mcont); - c_can_object_put(dev, iface, objno, IF_COMM_ALL & ~IF_COMM_TXRQST); - - netdev_dbg(dev, "obj no:%d, msgval:0x%08x\n", objno, - c_can_read_reg32(priv, C_CAN_MSGVAL1_REG)); -} - -static void c_can_inval_msg_object(struct net_device *dev, int iface, int objno) -{ - struct c_can_priv *priv = netdev_priv(dev); - - priv->write_reg(priv, C_CAN_IFACE(ARB1_REG, iface), 0); - priv->write_reg(priv, C_CAN_IFACE(ARB2_REG, iface), 0); - priv->write_reg(priv, C_CAN_IFACE(MSGCTRL_REG, iface), 0); - - c_can_object_put(dev, iface, objno, IF_COMM_ARB | IF_COMM_CONTROL); - - netdev_dbg(dev, "obj no:%d, msgval:0x%08x\n", objno, - c_can_read_reg32(priv, C_CAN_MSGVAL1_REG)); -} - -static inline int c_can_is_next_tx_obj_busy(struct c_can_priv *priv, int objno) -{ - int val = c_can_read_reg32(priv, C_CAN_TXRQST1_REG); - - /* - * as transmission request register's bit n-1 corresponds to - * message object n, we need to handle the same properly. - */ - if (val & (1 << (objno - 1))) - return 1; - - return 0; + c_can_object_put(dev, iface, obj, IF_COMM_RCV_SETUP); } static netdev_tx_t c_can_start_xmit(struct sk_buff *skb, - struct net_device *dev) + struct net_device *dev) { - u32 msg_obj_no; - struct c_can_priv *priv = netdev_priv(dev); struct can_frame *frame = (struct can_frame *)skb->data; + struct c_can_priv *priv = netdev_priv(dev); + u32 idx, obj; if (can_dropped_invalid_skb(dev, skb)) return NETDEV_TX_OK; - - msg_obj_no = get_tx_next_msg_obj(priv); - - /* prepare message object for transmission */ - c_can_write_msg_object(dev, 0, frame, msg_obj_no); - can_put_echo_skb(skb, dev, msg_obj_no - C_CAN_MSG_OBJ_TX_FIRST); - /* - * we have to stop the queue in case of a wrap around or - * if the next TX message object is still in use + * This is not a FIFO. C/D_CAN sends out the buffers + * prioritized. The lowest buffer number wins. */ - priv->tx_next++; - if (c_can_is_next_tx_obj_busy(priv, get_tx_next_msg_obj(priv)) || - (priv->tx_next & C_CAN_NEXT_MSG_OBJ_MASK) == 0) + idx = fls(atomic_read(&priv->tx_active)); + obj = idx + C_CAN_MSG_OBJ_TX_FIRST; + + /* If this is the last buffer, stop the xmit queue */ + if (idx == C_CAN_MSG_OBJ_TX_NUM - 1) netif_stop_queue(dev); + /* + * Store the message in the interface so we can call + * can_put_echo_skb(). We must do this before we enable + * transmit as we might race against do_tx(). + */ + c_can_setup_tx_object(dev, IF_TX, frame, idx); + priv->dlc[idx] = frame->can_dlc; + can_put_echo_skb(skb, dev, idx); + + /* Update the active bits */ + atomic_add((1 << idx), &priv->tx_active); + /* Start transmission */ + c_can_object_put(dev, IF_TX, obj, IF_COMM_TX); return NETDEV_TX_OK; } +static int c_can_wait_for_ctrl_init(struct net_device *dev, + struct c_can_priv *priv, u32 init) +{ + int retry = 0; + + while (init != (priv->read_reg(priv, C_CAN_CTRL_REG) & CONTROL_INIT)) { + udelay(10); + if (retry++ > 1000) { + netdev_err(dev, "CCTRL: set CONTROL_INIT failed\n"); + return -EIO; + } + } + return 0; +} + static int c_can_set_bittiming(struct net_device *dev) { unsigned int reg_btr, reg_brpe, ctrl_save; @@ -573,6 +488,7 @@ static int c_can_set_bittiming(struct net_device *dev) u32 ten_bit_brp; struct c_can_priv *priv = netdev_priv(dev); const struct can_bittiming *bt = &priv->can.bittiming; + int res; /* c_can provides a 6-bit brp and 4-bit brpe fields */ ten_bit_brp = bt->brp - 1; @@ -590,13 +506,17 @@ static int c_can_set_bittiming(struct net_device *dev) "setting BTR=%04x BRPE=%04x\n", reg_btr, reg_brpe); ctrl_save = priv->read_reg(priv, C_CAN_CTRL_REG); - priv->write_reg(priv, C_CAN_CTRL_REG, - ctrl_save | CONTROL_CCE | CONTROL_INIT); + ctrl_save &= ~CONTROL_INIT; + priv->write_reg(priv, C_CAN_CTRL_REG, CONTROL_CCE | CONTROL_INIT); + res = c_can_wait_for_ctrl_init(dev, priv, CONTROL_INIT); + if (res) + return res; + priv->write_reg(priv, C_CAN_BTR_REG, reg_btr); priv->write_reg(priv, C_CAN_BRPEXT_REG, reg_brpe); priv->write_reg(priv, C_CAN_CTRL_REG, ctrl_save); - return 0; + return c_can_wait_for_ctrl_init(dev, priv, 0); } /* @@ -614,15 +534,14 @@ static void c_can_configure_msg_objects(struct net_device *dev) /* first invalidate all message objects */ for (i = C_CAN_MSG_OBJ_RX_FIRST; i <= C_CAN_NO_OF_OBJECTS; i++) - c_can_inval_msg_object(dev, 0, i); + c_can_inval_msg_object(dev, IF_RX, i); /* setup receive message objects */ for (i = C_CAN_MSG_OBJ_RX_FIRST; i < C_CAN_MSG_OBJ_RX_LAST; i++) - c_can_setup_receive_object(dev, 0, i, 0, 0, - (IF_MCONT_RXIE | IF_MCONT_UMASK) & ~IF_MCONT_EOB); + c_can_setup_receive_object(dev, IF_RX, i, 0, 0, IF_MCONT_RCV); - c_can_setup_receive_object(dev, 0, C_CAN_MSG_OBJ_RX_LAST, 0, 0, - IF_MCONT_EOB | IF_MCONT_RXIE | IF_MCONT_UMASK); + c_can_setup_receive_object(dev, IF_RX, C_CAN_MSG_OBJ_RX_LAST, 0, 0, + IF_MCONT_RCV_EOB); } /* @@ -631,35 +550,27 @@ static void c_can_configure_msg_objects(struct net_device *dev) * - set operating mode * - configure message objects */ -static void c_can_chip_config(struct net_device *dev) +static int c_can_chip_config(struct net_device *dev) { struct c_can_priv *priv = netdev_priv(dev); /* enable automatic retransmission */ - priv->write_reg(priv, C_CAN_CTRL_REG, - CONTROL_ENABLE_AR); + priv->write_reg(priv, C_CAN_CTRL_REG, CONTROL_ENABLE_AR); if ((priv->can.ctrlmode & CAN_CTRLMODE_LISTENONLY) && (priv->can.ctrlmode & CAN_CTRLMODE_LOOPBACK)) { /* loopback + silent mode : useful for hot self-test */ - priv->write_reg(priv, C_CAN_CTRL_REG, CONTROL_EIE | - CONTROL_SIE | CONTROL_IE | CONTROL_TEST); - priv->write_reg(priv, C_CAN_TEST_REG, - TEST_LBACK | TEST_SILENT); + priv->write_reg(priv, C_CAN_CTRL_REG, CONTROL_TEST); + priv->write_reg(priv, C_CAN_TEST_REG, TEST_LBACK | TEST_SILENT); } else if (priv->can.ctrlmode & CAN_CTRLMODE_LOOPBACK) { /* loopback mode : useful for self-test function */ - priv->write_reg(priv, C_CAN_CTRL_REG, CONTROL_EIE | - CONTROL_SIE | CONTROL_IE | CONTROL_TEST); + priv->write_reg(priv, C_CAN_CTRL_REG, CONTROL_TEST); priv->write_reg(priv, C_CAN_TEST_REG, TEST_LBACK); } else if (priv->can.ctrlmode & CAN_CTRLMODE_LISTENONLY) { /* silent mode : bus-monitoring mode */ - priv->write_reg(priv, C_CAN_CTRL_REG, CONTROL_EIE | - CONTROL_SIE | CONTROL_IE | CONTROL_TEST); + priv->write_reg(priv, C_CAN_CTRL_REG, CONTROL_TEST); priv->write_reg(priv, C_CAN_TEST_REG, TEST_SILENT); - } else - /* normal mode*/ - priv->write_reg(priv, C_CAN_CTRL_REG, - CONTROL_EIE | CONTROL_SIE | CONTROL_IE); + } /* configure message objects */ c_can_configure_msg_objects(dev); @@ -667,43 +578,54 @@ static void c_can_chip_config(struct net_device *dev) /* set a `lec` value so that we can check for updates later */ priv->write_reg(priv, C_CAN_STS_REG, LEC_UNUSED); + /* Clear all internal status */ + atomic_set(&priv->tx_active, 0); + priv->rxmasked = 0; + priv->tx_dir = 0; + /* set bittiming params */ - c_can_set_bittiming(dev); + return c_can_set_bittiming(dev); } -static void c_can_start(struct net_device *dev) +static int c_can_start(struct net_device *dev) { struct c_can_priv *priv = netdev_priv(dev); + int err; /* basic c_can configuration */ - c_can_chip_config(dev); + err = c_can_chip_config(dev); + if (err) + return err; - priv->can.state = CAN_STATE_ERROR_ACTIVE; + /* Setup the command for new messages */ + priv->comm_rcv_high = priv->type != BOSCH_D_CAN ? + IF_COMM_RCV_LOW : IF_COMM_RCV_HIGH; - /* reset tx helper pointers */ - priv->tx_next = priv->tx_echo = 0; + priv->can.state = CAN_STATE_ERROR_ACTIVE; - /* enable status change, error and module interrupts */ - c_can_enable_all_interrupts(priv, ENABLE_ALL_INTERRUPTS); + return 0; } static void c_can_stop(struct net_device *dev) { struct c_can_priv *priv = netdev_priv(dev); - /* disable all interrupts */ - c_can_enable_all_interrupts(priv, DISABLE_ALL_INTERRUPTS); - - /* set the state as STOPPED */ + c_can_irq_control(priv, false); priv->can.state = CAN_STATE_STOPPED; } static int c_can_set_mode(struct net_device *dev, enum can_mode mode) { + struct c_can_priv *priv = netdev_priv(dev); + int err; + switch (mode) { case CAN_MODE_START: - c_can_start(dev); + err = c_can_start(dev); + if (err) + return err; netif_wake_queue(dev); + c_can_irq_control(priv, true); break; default: return -EOPNOTSUPP; @@ -712,63 +634,153 @@ static int c_can_set_mode(struct net_device *dev, enum can_mode mode) return 0; } -static int c_can_get_berr_counter(const struct net_device *dev, - struct can_berr_counter *bec) +static int __c_can_get_berr_counter(const struct net_device *dev, + struct can_berr_counter *bec) { unsigned int reg_err_counter; struct c_can_priv *priv = netdev_priv(dev); - c_can_pm_runtime_get_sync(priv); - reg_err_counter = priv->read_reg(priv, C_CAN_ERR_CNT_REG); bec->rxerr = (reg_err_counter & ERR_CNT_REC_MASK) >> ERR_CNT_REC_SHIFT; bec->txerr = reg_err_counter & ERR_CNT_TEC_MASK; + return 0; +} + +static int c_can_get_berr_counter(const struct net_device *dev, + struct can_berr_counter *bec) +{ + struct c_can_priv *priv = netdev_priv(dev); + int err; + + c_can_pm_runtime_get_sync(priv); + err = __c_can_get_berr_counter(dev, bec); c_can_pm_runtime_put_sync(priv); - return 0; + return err; } -/* - * theory of operation: - * - * priv->tx_echo holds the number of the oldest can_frame put for - * transmission into the hardware, but not yet ACKed by the CAN tx - * complete IRQ. - * - * We iterate from priv->tx_echo to priv->tx_next and check if the - * packet has been transmitted, echo it back to the CAN framework. - * If we discover a not yet transmitted packet, stop looking for more. - */ static void c_can_do_tx(struct net_device *dev) { - u32 val; - u32 msg_obj_no; struct c_can_priv *priv = netdev_priv(dev); struct net_device_stats *stats = &dev->stats; + u32 idx, obj, pkts = 0, bytes = 0, pend, clr; + + clr = pend = priv->read_reg(priv, C_CAN_INTPND2_REG); + + while ((idx = ffs(pend))) { + idx--; + pend &= ~(1 << idx); + obj = idx + C_CAN_MSG_OBJ_TX_FIRST; + c_can_inval_tx_object(dev, IF_RX, obj); + can_get_echo_skb(dev, idx); + bytes += priv->dlc[idx]; + pkts++; + } - for (/* nix */; (priv->tx_next - priv->tx_echo) > 0; priv->tx_echo++) { - msg_obj_no = get_tx_echo_msg_obj(priv); - val = c_can_read_reg32(priv, C_CAN_TXRQST1_REG); - if (!(val & (1 << (msg_obj_no - 1)))) { - can_get_echo_skb(dev, - msg_obj_no - C_CAN_MSG_OBJ_TX_FIRST); - stats->tx_bytes += priv->read_reg(priv, - C_CAN_IFACE(MSGCTRL_REG, 0)) - & IF_MCONT_DLC_MASK; - stats->tx_packets++; - can_led_event(dev, CAN_LED_EVENT_TX); - c_can_inval_msg_object(dev, 0, msg_obj_no); - } else { - break; + /* Clear the bits in the tx_active mask */ + atomic_sub(clr, &priv->tx_active); + + if (clr & (1 << (C_CAN_MSG_OBJ_TX_NUM - 1))) + netif_wake_queue(dev); + + if (pkts) { + stats->tx_bytes += bytes; + stats->tx_packets += pkts; + can_led_event(dev, CAN_LED_EVENT_TX); + } +} + +/* + * If we have a gap in the pending bits, that means we either + * raced with the hardware or failed to readout all upper + * objects in the last run due to quota limit. + */ +static u32 c_can_adjust_pending(u32 pend) +{ + u32 weight, lasts; + + if (pend == RECEIVE_OBJECT_BITS) + return pend; + + /* + * If the last set bit is larger than the number of pending + * bits we have a gap. + */ + weight = hweight32(pend); + lasts = fls(pend); + + /* If the bits are linear, nothing to do */ + if (lasts == weight) + return pend; + + /* + * Find the first set bit after the gap. We walk backwards + * from the last set bit. + */ + for (lasts--; pend & (1 << (lasts - 1)); lasts--); + + return pend & ~((1 << lasts) - 1); +} + +static inline void c_can_rx_object_get(struct net_device *dev, + struct c_can_priv *priv, u32 obj) +{ + c_can_object_get(dev, IF_RX, obj, priv->comm_rcv_high); +} + +static inline void c_can_rx_finalize(struct net_device *dev, + struct c_can_priv *priv, u32 obj) +{ + if (priv->type != BOSCH_D_CAN) + c_can_object_get(dev, IF_RX, obj, IF_COMM_CLR_NEWDAT); +} + +static int c_can_read_objects(struct net_device *dev, struct c_can_priv *priv, + u32 pend, int quota) +{ + u32 pkts = 0, ctrl, obj; + + while ((obj = ffs(pend)) && quota > 0) { + pend &= ~BIT(obj - 1); + + c_can_rx_object_get(dev, priv, obj); + ctrl = priv->read_reg(priv, C_CAN_IFACE(MSGCTRL_REG, IF_RX)); + + if (ctrl & IF_MCONT_MSGLST) { + int n = c_can_handle_lost_msg_obj(dev, IF_RX, obj, ctrl); + + pkts += n; + quota -= n; + continue; } + + /* + * This really should not happen, but this covers some + * odd HW behaviour. Do not remove that unless you + * want to brick your machine. + */ + if (!(ctrl & IF_MCONT_NEWDAT)) + continue; + + /* read the data from the message object */ + c_can_read_msg_object(dev, IF_RX, ctrl); + + c_can_rx_finalize(dev, priv, obj); + + pkts++; + quota--; } - /* restart queue if wrap-up or if queue stalled on last pkt */ - if (((priv->tx_next & C_CAN_NEXT_MSG_OBJ_MASK) != 0) || - ((priv->tx_echo & C_CAN_NEXT_MSG_OBJ_MASK) == 0)) - netif_wake_queue(dev); + return pkts; +} + +static inline u32 c_can_get_pending(struct c_can_priv *priv) +{ + u32 pend = priv->read_reg(priv, C_CAN_NEWDAT1_REG); + + return pend; } /* @@ -780,80 +792,47 @@ static void c_can_do_tx(struct net_device *dev) * has arrived. To work-around this issue, we keep two groups of message * objects whose partitioning is defined by C_CAN_MSG_OBJ_RX_SPLIT. * - * To ensure in-order frame reception we use the following - * approach while re-activating a message object to receive further - * frames: - * - if the current message object number is lower than - * C_CAN_MSG_RX_LOW_LAST, do not clear the NEWDAT bit while clearing - * the INTPND bit. - * - if the current message object number is equal to - * C_CAN_MSG_RX_LOW_LAST then clear the NEWDAT bit of all lower - * receive message objects. - * - if the current message object number is greater than - * C_CAN_MSG_RX_LOW_LAST then clear the NEWDAT bit of - * only this message object. + * We clear the newdat bit right away. + * + * This can result in packet reordering when the readout is slow. */ static int c_can_do_rx_poll(struct net_device *dev, int quota) { - u32 num_rx_pkts = 0; - unsigned int msg_obj, msg_ctrl_save; struct c_can_priv *priv = netdev_priv(dev); - u32 val = c_can_read_reg32(priv, C_CAN_INTPND1_REG); + u32 pkts = 0, pend = 0, toread, n; - for (msg_obj = C_CAN_MSG_OBJ_RX_FIRST; - msg_obj <= C_CAN_MSG_OBJ_RX_LAST && quota > 0; - val = c_can_read_reg32(priv, C_CAN_INTPND1_REG), - msg_obj++) { - /* - * as interrupt pending register's bit n-1 corresponds to - * message object n, we need to handle the same properly. - */ - if (val & (1 << (msg_obj - 1))) { - c_can_object_get(dev, 0, msg_obj, IF_COMM_ALL & - ~IF_COMM_TXRQST); - msg_ctrl_save = priv->read_reg(priv, - C_CAN_IFACE(MSGCTRL_REG, 0)); - - if (msg_ctrl_save & IF_MCONT_EOB) - return num_rx_pkts; - - if (msg_ctrl_save & IF_MCONT_MSGLST) { - c_can_handle_lost_msg_obj(dev, 0, msg_obj); - num_rx_pkts++; - quota--; - continue; - } - - if (!(msg_ctrl_save & IF_MCONT_NEWDAT)) - continue; - - /* read the data from the message object */ - c_can_read_msg_object(dev, 0, msg_ctrl_save); - - if (msg_obj < C_CAN_MSG_RX_LOW_LAST) - c_can_mark_rx_msg_obj(dev, 0, - msg_ctrl_save, msg_obj); - else if (msg_obj > C_CAN_MSG_RX_LOW_LAST) - /* activate this msg obj */ - c_can_activate_rx_msg_obj(dev, 0, - msg_ctrl_save, msg_obj); - else if (msg_obj == C_CAN_MSG_RX_LOW_LAST) - /* activate all lower message objects */ - c_can_activate_all_lower_rx_msg_obj(dev, - 0, msg_ctrl_save); - - num_rx_pkts++; - quota--; + /* + * It is faster to read only one 16bit register. This is only possible + * for a maximum number of 16 objects. + */ + BUILD_BUG_ON_MSG(C_CAN_MSG_OBJ_RX_LAST > 16, + "Implementation does not support more message objects than 16"); + + while (quota > 0) { + if (!pend) { + pend = c_can_get_pending(priv); + if (!pend) + break; + /* + * If the pending field has a gap, handle the + * bits above the gap first. + */ + toread = c_can_adjust_pending(pend); + } else { + toread = pend; } + /* Remove the bits from pend */ + pend &= ~toread; + /* Read the objects */ + n = c_can_read_objects(dev, priv, toread, quota); + pkts += n; + quota -= n; } - return num_rx_pkts; -} + if (pkts) + can_led_event(dev, CAN_LED_EVENT_RX); -static inline int c_can_has_and_handle_berr(struct c_can_priv *priv) -{ - return (priv->can.ctrlmode & CAN_CTRLMODE_BERR_REPORTING) && - (priv->current_status & LEC_UNUSED); + return pkts; } static int c_can_handle_state_change(struct net_device *dev, @@ -867,12 +846,32 @@ static int c_can_handle_state_change(struct net_device *dev, struct sk_buff *skb; struct can_berr_counter bec; + switch (error_type) { + case C_CAN_ERROR_WARNING: + /* error warning state */ + priv->can.can_stats.error_warning++; + priv->can.state = CAN_STATE_ERROR_WARNING; + break; + case C_CAN_ERROR_PASSIVE: + /* error passive state */ + priv->can.can_stats.error_passive++; + priv->can.state = CAN_STATE_ERROR_PASSIVE; + break; + case C_CAN_BUS_OFF: + /* bus-off state */ + priv->can.state = CAN_STATE_BUS_OFF; + can_bus_off(dev); + break; + default: + break; + } + /* propagate the error condition to the CAN stack */ skb = alloc_can_err_skb(dev, &cf); if (unlikely(!skb)) return 0; - c_can_get_berr_counter(dev, &bec); + __c_can_get_berr_counter(dev, &bec); reg_err_counter = priv->read_reg(priv, C_CAN_ERR_CNT_REG); rx_err_passive = (reg_err_counter & ERR_CNT_RP_MASK) >> ERR_CNT_RP_SHIFT; @@ -880,8 +879,6 @@ static int c_can_handle_state_change(struct net_device *dev, switch (error_type) { case C_CAN_ERROR_WARNING: /* error warning state */ - priv->can.can_stats.error_warning++; - priv->can.state = CAN_STATE_ERROR_WARNING; cf->can_id |= CAN_ERR_CRTL; cf->data[1] = (bec.txerr > bec.rxerr) ? CAN_ERR_CRTL_TX_WARNING : @@ -892,8 +889,6 @@ static int c_can_handle_state_change(struct net_device *dev, break; case C_CAN_ERROR_PASSIVE: /* error passive state */ - priv->can.can_stats.error_passive++; - priv->can.state = CAN_STATE_ERROR_PASSIVE; cf->can_id |= CAN_ERR_CRTL; if (rx_err_passive) cf->data[1] |= CAN_ERR_CRTL_RX_PASSIVE; @@ -905,22 +900,16 @@ static int c_can_handle_state_change(struct net_device *dev, break; case C_CAN_BUS_OFF: /* bus-off state */ - priv->can.state = CAN_STATE_BUS_OFF; cf->can_id |= CAN_ERR_BUSOFF; - /* - * disable all interrupts in bus-off mode to ensure that - * the CPU is not hogged down - */ - c_can_enable_all_interrupts(priv, DISABLE_ALL_INTERRUPTS); can_bus_off(dev); break; default: break; } - netif_receive_skb(skb); stats->rx_packets++; stats->rx_bytes += cf->can_dlc; + netif_receive_skb(skb); return 1; } @@ -941,6 +930,13 @@ static int c_can_handle_bus_err(struct net_device *dev, if (lec_type == LEC_UNUSED || lec_type == LEC_NO_ERROR) return 0; + if (!(priv->can.ctrlmode & CAN_CTRLMODE_BERR_REPORTING)) + return 0; + + /* common for all type of bus errors */ + priv->can.can_stats.bus_error++; + stats->rx_errors++; + /* propagate the error condition to the CAN stack */ skb = alloc_can_err_skb(dev, &cf); if (unlikely(!skb)) @@ -950,10 +946,6 @@ static int c_can_handle_bus_err(struct net_device *dev, * check for 'last error code' which tells us the * type of the last error to occur on the CAN bus */ - - /* common for all type of bus errors */ - priv->can.can_stats.bus_error++; - stats->rx_errors++; cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR; cf->data[2] |= CAN_ERR_PROT_UNSPEC; @@ -988,95 +980,64 @@ static int c_can_handle_bus_err(struct net_device *dev, break; } - /* set a `lec` value so that we can check for updates later */ - priv->write_reg(priv, C_CAN_STS_REG, LEC_UNUSED); - - netif_receive_skb(skb); stats->rx_packets++; stats->rx_bytes += cf->can_dlc; - + netif_receive_skb(skb); return 1; } static int c_can_poll(struct napi_struct *napi, int quota) { - u16 irqstatus; - int lec_type = 0; - int work_done = 0; struct net_device *dev = napi->dev; struct c_can_priv *priv = netdev_priv(dev); + u16 curr, last = priv->last_status; + int work_done = 0; - irqstatus = priv->irqstatus; - if (!irqstatus) - goto end; + priv->last_status = curr = priv->read_reg(priv, C_CAN_STS_REG); + /* Ack status on C_CAN. D_CAN is self clearing */ + if (priv->type != BOSCH_D_CAN) + priv->write_reg(priv, C_CAN_STS_REG, LEC_UNUSED); - /* status events have the highest priority */ - if (irqstatus == STATUS_INTERRUPT) { - priv->current_status = priv->read_reg(priv, - C_CAN_STS_REG); - - /* handle Tx/Rx events */ - if (priv->current_status & STATUS_TXOK) - priv->write_reg(priv, C_CAN_STS_REG, - priv->current_status & ~STATUS_TXOK); - - if (priv->current_status & STATUS_RXOK) - priv->write_reg(priv, C_CAN_STS_REG, - priv->current_status & ~STATUS_RXOK); - - /* handle state changes */ - if ((priv->current_status & STATUS_EWARN) && - (!(priv->last_status & STATUS_EWARN))) { - netdev_dbg(dev, "entered error warning state\n"); - work_done += c_can_handle_state_change(dev, - C_CAN_ERROR_WARNING); - } - if ((priv->current_status & STATUS_EPASS) && - (!(priv->last_status & STATUS_EPASS))) { - netdev_dbg(dev, "entered error passive state\n"); - work_done += c_can_handle_state_change(dev, - C_CAN_ERROR_PASSIVE); - } - if ((priv->current_status & STATUS_BOFF) && - (!(priv->last_status & STATUS_BOFF))) { - netdev_dbg(dev, "entered bus off state\n"); - work_done += c_can_handle_state_change(dev, - C_CAN_BUS_OFF); - } + /* handle state changes */ + if ((curr & STATUS_EWARN) && (!(last & STATUS_EWARN))) { + netdev_dbg(dev, "entered error warning state\n"); + work_done += c_can_handle_state_change(dev, C_CAN_ERROR_WARNING); + } - /* handle bus recovery events */ - if ((!(priv->current_status & STATUS_BOFF)) && - (priv->last_status & STATUS_BOFF)) { - netdev_dbg(dev, "left bus off state\n"); - priv->can.state = CAN_STATE_ERROR_ACTIVE; - } - if ((!(priv->current_status & STATUS_EPASS)) && - (priv->last_status & STATUS_EPASS)) { - netdev_dbg(dev, "left error passive state\n"); - priv->can.state = CAN_STATE_ERROR_ACTIVE; - } + if ((curr & STATUS_EPASS) && (!(last & STATUS_EPASS))) { + netdev_dbg(dev, "entered error passive state\n"); + work_done += c_can_handle_state_change(dev, C_CAN_ERROR_PASSIVE); + } - priv->last_status = priv->current_status; - - /* handle lec errors on the bus */ - lec_type = c_can_has_and_handle_berr(priv); - if (lec_type) - work_done += c_can_handle_bus_err(dev, lec_type); - } else if ((irqstatus >= C_CAN_MSG_OBJ_RX_FIRST) && - (irqstatus <= C_CAN_MSG_OBJ_RX_LAST)) { - /* handle events corresponding to receive message objects */ - work_done += c_can_do_rx_poll(dev, (quota - work_done)); - } else if ((irqstatus >= C_CAN_MSG_OBJ_TX_FIRST) && - (irqstatus <= C_CAN_MSG_OBJ_TX_LAST)) { - /* handle events corresponding to transmit message objects */ - c_can_do_tx(dev); + if ((curr & STATUS_BOFF) && (!(last & STATUS_BOFF))) { + netdev_dbg(dev, "entered bus off state\n"); + work_done += c_can_handle_state_change(dev, C_CAN_BUS_OFF); + goto end; + } + + /* handle bus recovery events */ + if ((!(curr & STATUS_BOFF)) && (last & STATUS_BOFF)) { + netdev_dbg(dev, "left bus off state\n"); + priv->can.state = CAN_STATE_ERROR_ACTIVE; } + if ((!(curr & STATUS_EPASS)) && (last & STATUS_EPASS)) { + netdev_dbg(dev, "left error passive state\n"); + priv->can.state = CAN_STATE_ERROR_ACTIVE; + } + + /* handle lec errors on the bus */ + work_done += c_can_handle_bus_err(dev, curr & LEC_MASK); + + /* Handle Tx/Rx events. We do this unconditionally */ + work_done += c_can_do_rx_poll(dev, (quota - work_done)); + c_can_do_tx(dev); end: if (work_done < quota) { napi_complete(napi); - /* enable all IRQs */ - c_can_enable_all_interrupts(priv, ENABLE_ALL_INTERRUPTS); + /* enable all IRQs if we are not in bus off state */ + if (priv->can.state != CAN_STATE_BUS_OFF) + c_can_irq_control(priv, true); } return work_done; @@ -1087,12 +1048,11 @@ static irqreturn_t c_can_isr(int irq, void *dev_id) struct net_device *dev = (struct net_device *)dev_id; struct c_can_priv *priv = netdev_priv(dev); - priv->irqstatus = priv->read_reg(priv, C_CAN_INT_REG); - if (!priv->irqstatus) + if (!priv->read_reg(priv, C_CAN_INT_REG)) return IRQ_NONE; /* disable all interrupts and schedule the NAPI */ - c_can_enable_all_interrupts(priv, DISABLE_ALL_INTERRUPTS); + c_can_irq_control(priv, false); napi_schedule(&priv->napi); return IRQ_HANDLED; @@ -1121,17 +1081,22 @@ static int c_can_open(struct net_device *dev) goto exit_irq_fail; } - napi_enable(&priv->napi); + /* start the c_can controller */ + err = c_can_start(dev); + if (err) + goto exit_start_fail; can_led_event(dev, CAN_LED_EVENT_OPEN); - /* start the c_can controller */ - c_can_start(dev); - + napi_enable(&priv->napi); + /* enable status change, error and module interrupts */ + c_can_irq_control(priv, true); netif_start_queue(dev); return 0; +exit_start_fail: + free_irq(dev->irq, dev); exit_irq_fail: close_candev(dev); exit_open_fail: @@ -1222,6 +1187,7 @@ int c_can_power_up(struct net_device *dev) u32 val; unsigned long time_out; struct c_can_priv *priv = netdev_priv(dev); + int ret; if (!(dev->flags & IFF_UP)) return 0; @@ -1248,15 +1214,20 @@ int c_can_power_up(struct net_device *dev) if (time_after(jiffies, time_out)) return -ETIMEDOUT; - c_can_start(dev); + ret = c_can_start(dev); + if (!ret) + c_can_irq_control(priv, true); - return 0; + return ret; } EXPORT_SYMBOL_GPL(c_can_power_up); #endif void free_c_can_dev(struct net_device *dev) { + struct c_can_priv *priv = netdev_priv(dev); + + netif_napi_del(&priv->napi); free_candev(dev); } EXPORT_SYMBOL_GPL(free_c_can_dev); @@ -1265,6 +1236,7 @@ static const struct net_device_ops c_can_netdev_ops = { .ndo_open = c_can_open, .ndo_stop = c_can_close, .ndo_start_xmit = c_can_start_xmit, + .ndo_change_mtu = can_change_mtu, }; int register_c_can_dev(struct net_device *dev) diff --git a/drivers/net/can/c_can/c_can.h b/drivers/net/can/c_can/c_can.h index d2e1c21b143..99ad1aa576b 100644 --- a/drivers/net/can/c_can/c_can.h +++ b/drivers/net/can/c_can/c_can.h @@ -22,6 +22,23 @@ #ifndef C_CAN_H #define C_CAN_H +/* message object split */ +#define C_CAN_NO_OF_OBJECTS 32 +#define C_CAN_MSG_OBJ_RX_NUM 16 +#define C_CAN_MSG_OBJ_TX_NUM 16 + +#define C_CAN_MSG_OBJ_RX_FIRST 1 +#define C_CAN_MSG_OBJ_RX_LAST (C_CAN_MSG_OBJ_RX_FIRST + \ + C_CAN_MSG_OBJ_RX_NUM - 1) + +#define C_CAN_MSG_OBJ_TX_FIRST (C_CAN_MSG_OBJ_RX_LAST + 1) +#define C_CAN_MSG_OBJ_TX_LAST (C_CAN_MSG_OBJ_TX_FIRST + \ + C_CAN_MSG_OBJ_TX_NUM - 1) + +#define C_CAN_MSG_OBJ_RX_SPLIT 9 +#define C_CAN_MSG_RX_LOW_LAST (C_CAN_MSG_OBJ_RX_SPLIT - 1) +#define RECEIVE_OBJECT_BITS 0x0000ffff + enum reg { C_CAN_CTRL_REG = 0, C_CAN_CTRL_EX_REG, @@ -61,6 +78,7 @@ enum reg { C_CAN_INTPND2_REG, C_CAN_MSGVAL1_REG, C_CAN_MSGVAL2_REG, + C_CAN_FUNCTION_REG, }; static const u16 reg_map_c_can[] = { @@ -112,6 +130,7 @@ static const u16 reg_map_d_can[] = { [C_CAN_BRPEXT_REG] = 0x0E, [C_CAN_INT_REG] = 0x10, [C_CAN_TEST_REG] = 0x14, + [C_CAN_FUNCTION_REG] = 0x18, [C_CAN_TXRQST1_REG] = 0x88, [C_CAN_TXRQST2_REG] = 0x8A, [C_CAN_NEWDAT1_REG] = 0x9C, @@ -156,22 +175,23 @@ struct c_can_priv { struct napi_struct napi; struct net_device *dev; struct device *device; - int tx_object; - int current_status; + atomic_t tx_active; + unsigned long tx_dir; int last_status; - u16 (*read_reg) (struct c_can_priv *priv, enum reg index); - void (*write_reg) (struct c_can_priv *priv, enum reg index, u16 val); + u16 (*read_reg) (const struct c_can_priv *priv, enum reg index); + void (*write_reg) (const struct c_can_priv *priv, enum reg index, u16 val); + u32 (*read_reg32) (const struct c_can_priv *priv, enum reg index); + void (*write_reg32) (const struct c_can_priv *priv, enum reg index, u32 val); void __iomem *base; const u16 *regs; - unsigned long irq_flags; /* for request_irq() */ - unsigned int tx_next; - unsigned int tx_echo; void *priv; /* for board-specific data */ - u16 irqstatus; enum c_can_dev_id type; u32 __iomem *raminit_ctrlreg; - unsigned int instance; + int instance; void (*raminit) (const struct c_can_priv *priv, bool enable); + u32 comm_rcv_high; + u32 rxmasked; + u32 dlc[C_CAN_MSG_OBJ_TX_NUM]; }; struct net_device *alloc_c_can_dev(void); diff --git a/drivers/net/can/c_can/c_can_pci.c b/drivers/net/can/c_can/c_can_pci.c index b374be7891a..5d11e0e4225 100644 --- a/drivers/net/can/c_can/c_can_pci.c +++ b/drivers/net/can/c_can/c_can_pci.c @@ -19,9 +19,13 @@ #include "c_can.h" +#define PCI_DEVICE_ID_PCH_CAN 0x8818 +#define PCH_PCI_SOFT_RESET 0x01fc + enum c_can_pci_reg_align { C_CAN_REG_ALIGN_16, C_CAN_REG_ALIGN_32, + C_CAN_REG_32, }; struct c_can_pci_data { @@ -31,6 +35,10 @@ struct c_can_pci_data { enum c_can_pci_reg_align reg_align; /* Set the frequency */ unsigned int freq; + /* PCI bar number */ + int bar; + /* Callback for reset */ + void (*init)(const struct c_can_priv *priv, bool enable); }; /* @@ -39,30 +47,70 @@ struct c_can_pci_data { * registers can be aligned to a 16-bit boundary or 32-bit boundary etc. * Handle the same by providing a common read/write interface. */ -static u16 c_can_pci_read_reg_aligned_to_16bit(struct c_can_priv *priv, +static u16 c_can_pci_read_reg_aligned_to_16bit(const struct c_can_priv *priv, enum reg index) { return readw(priv->base + priv->regs[index]); } -static void c_can_pci_write_reg_aligned_to_16bit(struct c_can_priv *priv, +static void c_can_pci_write_reg_aligned_to_16bit(const struct c_can_priv *priv, enum reg index, u16 val) { writew(val, priv->base + priv->regs[index]); } -static u16 c_can_pci_read_reg_aligned_to_32bit(struct c_can_priv *priv, +static u16 c_can_pci_read_reg_aligned_to_32bit(const struct c_can_priv *priv, enum reg index) { return readw(priv->base + 2 * priv->regs[index]); } -static void c_can_pci_write_reg_aligned_to_32bit(struct c_can_priv *priv, +static void c_can_pci_write_reg_aligned_to_32bit(const struct c_can_priv *priv, enum reg index, u16 val) { writew(val, priv->base + 2 * priv->regs[index]); } +static u16 c_can_pci_read_reg_32bit(const struct c_can_priv *priv, + enum reg index) +{ + return (u16)ioread32(priv->base + 2 * priv->regs[index]); +} + +static void c_can_pci_write_reg_32bit(const struct c_can_priv *priv, + enum reg index, u16 val) +{ + iowrite32((u32)val, priv->base + 2 * priv->regs[index]); +} + +static u32 c_can_pci_read_reg32(const struct c_can_priv *priv, enum reg index) +{ + u32 val; + + val = priv->read_reg(priv, index); + val |= ((u32) priv->read_reg(priv, index + 1)) << 16; + + return val; +} + +static void c_can_pci_write_reg32(const struct c_can_priv *priv, enum reg index, + u32 val) +{ + priv->write_reg(priv, index + 1, val >> 16); + priv->write_reg(priv, index, val); +} + +static void c_can_pci_reset_pch(const struct c_can_priv *priv, bool enable) +{ + if (enable) { + u32 __iomem *addr = priv->base + PCH_PCI_SOFT_RESET; + + /* write to sw reset register */ + iowrite32(1, addr); + iowrite32(0, addr); + } +} + static int c_can_pci_probe(struct pci_dev *pdev, const struct pci_device_id *ent) { @@ -84,10 +132,14 @@ static int c_can_pci_probe(struct pci_dev *pdev, goto out_disable_device; } - pci_set_master(pdev); - pci_enable_msi(pdev); + ret = pci_enable_msi(pdev); + if (!ret) { + dev_info(&pdev->dev, "MSI enabled\n"); + pci_set_master(pdev); + } - addr = pci_iomap(pdev, 0, pci_resource_len(pdev, 0)); + addr = pci_iomap(pdev, c_can_pci_data->bar, + pci_resource_len(pdev, c_can_pci_data->bar)); if (!addr) { dev_err(&pdev->dev, "device has no PCI memory resources, " @@ -132,6 +184,8 @@ static int c_can_pci_probe(struct pci_dev *pdev, goto out_free_c_can; } + priv->type = c_can_pci_data->type; + /* Configure access to registers */ switch (c_can_pci_data->reg_align) { case C_CAN_REG_ALIGN_32: @@ -142,10 +196,18 @@ static int c_can_pci_probe(struct pci_dev *pdev, priv->read_reg = c_can_pci_read_reg_aligned_to_16bit; priv->write_reg = c_can_pci_write_reg_aligned_to_16bit; break; + case C_CAN_REG_32: + priv->read_reg = c_can_pci_read_reg_32bit; + priv->write_reg = c_can_pci_write_reg_32bit; + break; default: ret = -EINVAL; goto out_free_c_can; } + priv->read_reg32 = c_can_pci_read_reg32; + priv->write_reg32 = c_can_pci_write_reg32; + + priv->raminit = c_can_pci_data->init; ret = register_c_can_dev(dev); if (ret) { @@ -160,7 +222,6 @@ static int c_can_pci_probe(struct pci_dev *pdev, return 0; out_free_c_can: - pci_set_drvdata(pdev, NULL); free_c_can_dev(dev); out_iounmap: pci_iounmap(pdev, addr); @@ -181,7 +242,6 @@ static void c_can_pci_remove(struct pci_dev *pdev) unregister_c_can_dev(dev); - pci_set_drvdata(pdev, NULL); free_c_can_dev(dev); pci_iounmap(pdev, priv->base); @@ -195,6 +255,15 @@ static struct c_can_pci_data c_can_sta2x11= { .type = BOSCH_C_CAN, .reg_align = C_CAN_REG_ALIGN_32, .freq = 52000000, /* 52 Mhz */ + .bar = 0, +}; + +static struct c_can_pci_data c_can_pch = { + .type = BOSCH_C_CAN, + .reg_align = C_CAN_REG_32, + .freq = 50000000, /* 50 MHz */ + .init = c_can_pci_reset_pch, + .bar = 1, }; #define C_CAN_ID(_vend, _dev, _driverdata) { \ @@ -204,6 +273,8 @@ static struct c_can_pci_data c_can_sta2x11= { static DEFINE_PCI_DEVICE_TABLE(c_can_pci_tbl) = { C_CAN_ID(PCI_VENDOR_ID_STMICRO, PCI_DEVICE_ID_STMICRO_CAN, c_can_sta2x11), + C_CAN_ID(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_PCH_CAN, + c_can_pch), {}, }; static struct pci_driver c_can_pci_driver = { diff --git a/drivers/net/can/c_can/c_can_platform.c b/drivers/net/can/c_can/c_can_platform.c index 294ced3cc22..12430be6448 100644 --- a/drivers/net/can/c_can/c_can_platform.c +++ b/drivers/net/can/c_can/c_can_platform.c @@ -37,48 +37,126 @@ #include "c_can.h" -#define CAN_RAMINIT_START_MASK(i) (1 << (i)) - +#define CAN_RAMINIT_START_MASK(i) (0x001 << (i)) +#define CAN_RAMINIT_DONE_MASK(i) (0x100 << (i)) +#define CAN_RAMINIT_ALL_MASK(i) (0x101 << (i)) +#define DCAN_RAM_INIT_BIT (1 << 3) +static DEFINE_SPINLOCK(raminit_lock); /* * 16-bit c_can registers can be arranged differently in the memory * architecture of different implementations. For example: 16-bit * registers can be aligned to a 16-bit boundary or 32-bit boundary etc. * Handle the same by providing a common read/write interface. */ -static u16 c_can_plat_read_reg_aligned_to_16bit(struct c_can_priv *priv, +static u16 c_can_plat_read_reg_aligned_to_16bit(const struct c_can_priv *priv, enum reg index) { return readw(priv->base + priv->regs[index]); } -static void c_can_plat_write_reg_aligned_to_16bit(struct c_can_priv *priv, +static void c_can_plat_write_reg_aligned_to_16bit(const struct c_can_priv *priv, enum reg index, u16 val) { writew(val, priv->base + priv->regs[index]); } -static u16 c_can_plat_read_reg_aligned_to_32bit(struct c_can_priv *priv, +static u16 c_can_plat_read_reg_aligned_to_32bit(const struct c_can_priv *priv, enum reg index) { return readw(priv->base + 2 * priv->regs[index]); } -static void c_can_plat_write_reg_aligned_to_32bit(struct c_can_priv *priv, +static void c_can_plat_write_reg_aligned_to_32bit(const struct c_can_priv *priv, enum reg index, u16 val) { writew(val, priv->base + 2 * priv->regs[index]); } -static void c_can_hw_raminit(const struct c_can_priv *priv, bool enable) +static void c_can_hw_raminit_wait_ti(const struct c_can_priv *priv, u32 mask, + u32 val) +{ + /* We look only at the bits of our instance. */ + val &= mask; + while ((readl(priv->raminit_ctrlreg) & mask) != val) + udelay(1); +} + +static void c_can_hw_raminit_ti(const struct c_can_priv *priv, bool enable) +{ + u32 mask = CAN_RAMINIT_ALL_MASK(priv->instance); + u32 ctrl; + + spin_lock(&raminit_lock); + + ctrl = readl(priv->raminit_ctrlreg); + /* We clear the done and start bit first. The start bit is + * looking at the 0 -> transition, but is not self clearing; + * And we clear the init done bit as well. + */ + ctrl &= ~CAN_RAMINIT_START_MASK(priv->instance); + ctrl |= CAN_RAMINIT_DONE_MASK(priv->instance); + writel(ctrl, priv->raminit_ctrlreg); + ctrl &= ~CAN_RAMINIT_DONE_MASK(priv->instance); + c_can_hw_raminit_wait_ti(priv, ctrl, mask); + + if (enable) { + /* Set start bit and wait for the done bit. */ + ctrl |= CAN_RAMINIT_START_MASK(priv->instance); + writel(ctrl, priv->raminit_ctrlreg); + ctrl |= CAN_RAMINIT_DONE_MASK(priv->instance); + c_can_hw_raminit_wait_ti(priv, ctrl, mask); + } + spin_unlock(&raminit_lock); +} + +static u32 c_can_plat_read_reg32(const struct c_can_priv *priv, enum reg index) { u32 val; - val = readl(priv->raminit_ctrlreg); - if (enable) - val |= CAN_RAMINIT_START_MASK(priv->instance); - else - val &= ~CAN_RAMINIT_START_MASK(priv->instance); - writel(val, priv->raminit_ctrlreg); + val = priv->read_reg(priv, index); + val |= ((u32) priv->read_reg(priv, index + 1)) << 16; + + return val; +} + +static void c_can_plat_write_reg32(const struct c_can_priv *priv, enum reg index, + u32 val) +{ + priv->write_reg(priv, index + 1, val >> 16); + priv->write_reg(priv, index, val); +} + +static u32 d_can_plat_read_reg32(const struct c_can_priv *priv, enum reg index) +{ + return readl(priv->base + priv->regs[index]); +} + +static void d_can_plat_write_reg32(const struct c_can_priv *priv, enum reg index, + u32 val) +{ + writel(val, priv->base + priv->regs[index]); +} + +static void c_can_hw_raminit_wait(const struct c_can_priv *priv, u32 mask) +{ + while (priv->read_reg32(priv, C_CAN_FUNCTION_REG) & mask) + udelay(1); +} + +static void c_can_hw_raminit(const struct c_can_priv *priv, bool enable) +{ + u32 ctrl; + + ctrl = priv->read_reg32(priv, C_CAN_FUNCTION_REG); + ctrl &= ~DCAN_RAM_INIT_BIT; + priv->write_reg32(priv, C_CAN_FUNCTION_REG, ctrl); + c_can_hw_raminit_wait(priv, ctrl); + + if (enable) { + ctrl |= DCAN_RAM_INIT_BIT; + priv->write_reg32(priv, C_CAN_FUNCTION_REG, ctrl); + c_can_hw_raminit_wait(priv, ctrl); + } } static struct platform_device_id c_can_id_table[] = { @@ -174,11 +252,15 @@ static int c_can_plat_probe(struct platform_device *pdev) case IORESOURCE_MEM_32BIT: priv->read_reg = c_can_plat_read_reg_aligned_to_32bit; priv->write_reg = c_can_plat_write_reg_aligned_to_32bit; + priv->read_reg32 = c_can_plat_read_reg32; + priv->write_reg32 = c_can_plat_write_reg32; break; case IORESOURCE_MEM_16BIT: default: priv->read_reg = c_can_plat_read_reg_aligned_to_16bit; priv->write_reg = c_can_plat_write_reg_aligned_to_16bit; + priv->read_reg32 = c_can_plat_read_reg32; + priv->write_reg32 = c_can_plat_write_reg32; break; } break; @@ -187,6 +269,8 @@ static int c_can_plat_probe(struct platform_device *pdev) priv->can.ctrlmode_supported |= CAN_CTRLMODE_3_SAMPLES; priv->read_reg = c_can_plat_read_reg_aligned_to_16bit; priv->write_reg = c_can_plat_write_reg_aligned_to_16bit; + priv->read_reg32 = d_can_plat_read_reg32; + priv->write_reg32 = d_can_plat_write_reg32; if (pdev->dev.of_node) priv->instance = of_alias_get_id(pdev->dev.of_node, "d_can"); @@ -194,11 +278,21 @@ static int c_can_plat_probe(struct platform_device *pdev) priv->instance = pdev->id; res = platform_get_resource(pdev, IORESOURCE_MEM, 1); - priv->raminit_ctrlreg = devm_ioremap_resource(&pdev->dev, res); - if (IS_ERR(priv->raminit_ctrlreg) || (int)priv->instance < 0) + /* Not all D_CAN modules have a separate register for the D_CAN + * RAM initialization. Use default RAM init bit in D_CAN module + * if not specified in DT. + */ + if (!res) { + priv->raminit = c_can_hw_raminit; + break; + } + + priv->raminit_ctrlreg = devm_ioremap(&pdev->dev, res->start, + resource_size(res)); + if (IS_ERR(priv->raminit_ctrlreg) || priv->instance < 0) dev_info(&pdev->dev, "control memory is not used for raminit\n"); else - priv->raminit = c_can_hw_raminit; + priv->raminit = c_can_hw_raminit_ti; break; default: ret = -EINVAL; @@ -322,7 +416,7 @@ static struct platform_driver c_can_plat_driver = { .driver = { .name = KBUILD_MODNAME, .owner = THIS_MODULE, - .of_match_table = of_match_ptr(c_can_of_table), + .of_match_table = c_can_of_table, }, .probe = c_can_plat_probe, .remove = c_can_plat_remove, diff --git a/drivers/net/can/cc770/cc770.c b/drivers/net/can/cc770/cc770.c index 0f12abf6591..d8379278d64 100644 --- a/drivers/net/can/cc770/cc770.c +++ b/drivers/net/can/cc770/cc770.c @@ -823,6 +823,7 @@ static const struct net_device_ops cc770_netdev_ops = { .ndo_open = cc770_open, .ndo_stop = cc770_close, .ndo_start_xmit = cc770_start_xmit, + .ndo_change_mtu = can_change_mtu, }; int register_cc770dev(struct net_device *dev) diff --git a/drivers/net/can/cc770/cc770_platform.c b/drivers/net/can/cc770/cc770_platform.c index 034bdd816a6..ad76734b3ec 100644 --- a/drivers/net/can/cc770/cc770_platform.c +++ b/drivers/net/can/cc770/cc770_platform.c @@ -152,7 +152,7 @@ static int cc770_get_platform_data(struct platform_device *pdev, struct cc770_priv *priv) { - struct cc770_platform_data *pdata = pdev->dev.platform_data; + struct cc770_platform_data *pdata = dev_get_platdata(&pdev->dev); priv->can.clock.freq = pdata->osc_freq; if (priv->cpu_interface & CPUIF_DSC) @@ -203,7 +203,7 @@ static int cc770_platform_probe(struct platform_device *pdev) if (pdev->dev.of_node) err = cc770_get_of_node_data(pdev, priv); - else if (pdev->dev.platform_data) + else if (dev_get_platdata(&pdev->dev)) err = cc770_get_platform_data(pdev, priv); else err = -ENODEV; diff --git a/drivers/net/can/dev.c b/drivers/net/can/dev.c index 1870c4731a5..e318e87e2bf 100644 --- a/drivers/net/can/dev.c +++ b/drivers/net/can/dev.c @@ -13,8 +13,7 @@ * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * along with this program; if not, see <http://www.gnu.org/licenses/>. */ #include <linux/module.h> @@ -100,10 +99,10 @@ static int can_update_spt(const struct can_bittiming_const *btc, return 1000 * (tseg + 1 - *tseg2) / (tseg + 1); } -static int can_calc_bittiming(struct net_device *dev, struct can_bittiming *bt) +static int can_calc_bittiming(struct net_device *dev, struct can_bittiming *bt, + const struct can_bittiming_const *btc) { struct can_priv *priv = netdev_priv(dev); - const struct can_bittiming_const *btc = priv->bittiming_const; long rate, best_rate = 0; long best_error = 1000000000, error = 0; int best_tseg = 0, best_brp = 0, brp = 0; @@ -111,9 +110,6 @@ static int can_calc_bittiming(struct net_device *dev, struct can_bittiming *bt) int spt_error = 1000, spt = 0, sampl_pt; u64 v64; - if (!priv->bittiming_const) - return -ENOTSUPP; - /* Use CIA recommended sample points */ if (bt->sample_point) { sampl_pt = bt->sample_point; @@ -205,7 +201,8 @@ static int can_calc_bittiming(struct net_device *dev, struct can_bittiming *bt) return 0; } #else /* !CONFIG_CAN_CALC_BITTIMING */ -static int can_calc_bittiming(struct net_device *dev, struct can_bittiming *bt) +static int can_calc_bittiming(struct net_device *dev, struct can_bittiming *bt, + const struct can_bittiming_const *btc) { netdev_err(dev, "bit-timing calculation not available\n"); return -EINVAL; @@ -218,16 +215,13 @@ static int can_calc_bittiming(struct net_device *dev, struct can_bittiming *bt) * prescaler value brp. You can find more information in the header * file linux/can/netlink.h. */ -static int can_fixup_bittiming(struct net_device *dev, struct can_bittiming *bt) +static int can_fixup_bittiming(struct net_device *dev, struct can_bittiming *bt, + const struct can_bittiming_const *btc) { struct can_priv *priv = netdev_priv(dev); - const struct can_bittiming_const *btc = priv->bittiming_const; int tseg1, alltseg; u64 brp64; - if (!priv->bittiming_const) - return -ENOTSUPP; - tseg1 = bt->prop_seg + bt->phase_seg1; if (!bt->sjw) bt->sjw = 1; @@ -255,26 +249,29 @@ static int can_fixup_bittiming(struct net_device *dev, struct can_bittiming *bt) return 0; } -static int can_get_bittiming(struct net_device *dev, struct can_bittiming *bt) +static int can_get_bittiming(struct net_device *dev, struct can_bittiming *bt, + const struct can_bittiming_const *btc) { - struct can_priv *priv = netdev_priv(dev); int err; /* Check if the CAN device has bit-timing parameters */ - if (priv->bittiming_const) { + if (!btc) + return -EOPNOTSUPP; - /* Non-expert mode? Check if the bitrate has been pre-defined */ - if (!bt->tq) - /* Determine bit-timing parameters */ - err = can_calc_bittiming(dev, bt); - else - /* Check bit-timing params and calculate proper brp */ - err = can_fixup_bittiming(dev, bt); - if (err) - return err; - } + /* + * Depending on the given can_bittiming parameter structure the CAN + * timing parameters are calculated based on the provided bitrate OR + * alternatively the CAN timing parameters (tq, prop_seg, etc.) are + * provided directly which are then checked and fixed up. + */ + if (!bt->tq && bt->bitrate) + err = can_calc_bittiming(dev, bt, btc); + else if (bt->tq && !bt->bitrate) + err = can_fixup_bittiming(dev, bt, btc); + else + err = -EINVAL; - return 0; + return err; } /* @@ -318,28 +315,20 @@ void can_put_echo_skb(struct sk_buff *skb, struct net_device *dev, BUG_ON(idx >= priv->echo_skb_max); /* check flag whether this packet has to be looped back */ - if (!(dev->flags & IFF_ECHO) || skb->pkt_type != PACKET_LOOPBACK) { + if (!(dev->flags & IFF_ECHO) || skb->pkt_type != PACKET_LOOPBACK || + (skb->protocol != htons(ETH_P_CAN) && + skb->protocol != htons(ETH_P_CANFD))) { kfree_skb(skb); return; } if (!priv->echo_skb[idx]) { - struct sock *srcsk = skb->sk; - if (atomic_read(&skb->users) != 1) { - struct sk_buff *old_skb = skb; - - skb = skb_clone(old_skb, GFP_ATOMIC); - kfree_skb(old_skb); - if (!skb) - return; - } else - skb_orphan(skb); - - skb->sk = srcsk; + skb = can_create_echo_skb(skb); + if (!skb) + return; /* make settings for echo to reduce code in irq context */ - skb->protocol = htons(ETH_P_CAN); skb->pkt_type = PACKET_BROADCAST; skb->ip_summed = CHECKSUM_UNNECESSARY; skb->dev = dev; @@ -522,6 +511,30 @@ struct sk_buff *alloc_can_skb(struct net_device *dev, struct can_frame **cf) } EXPORT_SYMBOL_GPL(alloc_can_skb); +struct sk_buff *alloc_canfd_skb(struct net_device *dev, + struct canfd_frame **cfd) +{ + struct sk_buff *skb; + + skb = netdev_alloc_skb(dev, sizeof(struct can_skb_priv) + + sizeof(struct canfd_frame)); + if (unlikely(!skb)) + return NULL; + + skb->protocol = htons(ETH_P_CANFD); + skb->pkt_type = PACKET_BROADCAST; + skb->ip_summed = CHECKSUM_UNNECESSARY; + + can_skb_reserve(skb); + can_skb_prv(skb)->ifindex = dev->ifindex; + + *cfd = (struct canfd_frame *)skb_put(skb, sizeof(struct canfd_frame)); + memset(*cfd, 0, sizeof(struct canfd_frame)); + + return skb; +} +EXPORT_SYMBOL_GPL(alloc_canfd_skb); + struct sk_buff *alloc_can_err_skb(struct net_device *dev, struct can_frame **cf) { struct sk_buff *skb; @@ -582,6 +595,39 @@ void free_candev(struct net_device *dev) EXPORT_SYMBOL_GPL(free_candev); /* + * changing MTU and control mode for CAN/CANFD devices + */ +int can_change_mtu(struct net_device *dev, int new_mtu) +{ + struct can_priv *priv = netdev_priv(dev); + + /* Do not allow changing the MTU while running */ + if (dev->flags & IFF_UP) + return -EBUSY; + + /* allow change of MTU according to the CANFD ability of the device */ + switch (new_mtu) { + case CAN_MTU: + priv->ctrlmode &= ~CAN_CTRLMODE_FD; + break; + + case CANFD_MTU: + if (!(priv->ctrlmode_supported & CAN_CTRLMODE_FD)) + return -EINVAL; + + priv->ctrlmode |= CAN_CTRLMODE_FD; + break; + + default: + return -EINVAL; + } + + dev->mtu = new_mtu; + return 0; +} +EXPORT_SYMBOL_GPL(can_change_mtu); + +/* * Common open function when the device gets opened. * * This function should be called in the open function of the device @@ -591,11 +637,19 @@ int open_candev(struct net_device *dev) { struct can_priv *priv = netdev_priv(dev); - if (!priv->bittiming.tq && !priv->bittiming.bitrate) { + if (!priv->bittiming.bitrate) { netdev_err(dev, "bit-timing not yet defined\n"); return -EINVAL; } + /* For CAN FD the data bitrate has to be >= the arbitration bitrate */ + if ((priv->ctrlmode & CAN_CTRLMODE_FD) && + (!priv->data_bittiming.bitrate || + (priv->data_bittiming.bitrate < priv->bittiming.bitrate))) { + netdev_err(dev, "incorrect/missing data bit-timing\n"); + return -EINVAL; + } + /* Switch carrier on if device was stopped while in bus-off state */ if (!netif_carrier_ok(dev)) netif_carrier_on(dev); @@ -634,6 +688,10 @@ static const struct nla_policy can_policy[IFLA_CAN_MAX + 1] = { = { .len = sizeof(struct can_bittiming_const) }, [IFLA_CAN_CLOCK] = { .len = sizeof(struct can_clock) }, [IFLA_CAN_BERR_COUNTER] = { .len = sizeof(struct can_berr_counter) }, + [IFLA_CAN_DATA_BITTIMING] + = { .len = sizeof(struct can_bittiming) }, + [IFLA_CAN_DATA_BITTIMING_CONST] + = { .len = sizeof(struct can_bittiming_const) }, }; static int can_changelink(struct net_device *dev, @@ -645,19 +703,6 @@ static int can_changelink(struct net_device *dev, /* We need synchronization with dev->stop() */ ASSERT_RTNL(); - if (data[IFLA_CAN_CTRLMODE]) { - struct can_ctrlmode *cm; - - /* Do not allow changing controller mode while running */ - if (dev->flags & IFF_UP) - return -EBUSY; - cm = nla_data(data[IFLA_CAN_CTRLMODE]); - if (cm->flags & ~priv->ctrlmode_supported) - return -EOPNOTSUPP; - priv->ctrlmode &= ~cm->mask; - priv->ctrlmode |= cm->flags; - } - if (data[IFLA_CAN_BITTIMING]) { struct can_bittiming bt; @@ -665,9 +710,7 @@ static int can_changelink(struct net_device *dev, if (dev->flags & IFF_UP) return -EBUSY; memcpy(&bt, nla_data(data[IFLA_CAN_BITTIMING]), sizeof(bt)); - if ((!bt.bitrate && !bt.tq) || (bt.bitrate && bt.tq)) - return -EINVAL; - err = can_get_bittiming(dev, &bt); + err = can_get_bittiming(dev, &bt, priv->bittiming_const); if (err) return err; memcpy(&priv->bittiming, &bt, sizeof(bt)); @@ -680,6 +723,25 @@ static int can_changelink(struct net_device *dev, } } + if (data[IFLA_CAN_CTRLMODE]) { + struct can_ctrlmode *cm; + + /* Do not allow changing controller mode while running */ + if (dev->flags & IFF_UP) + return -EBUSY; + cm = nla_data(data[IFLA_CAN_CTRLMODE]); + if (cm->flags & ~priv->ctrlmode_supported) + return -EOPNOTSUPP; + priv->ctrlmode &= ~cm->mask; + priv->ctrlmode |= cm->flags; + + /* CAN_CTRLMODE_FD can only be set when driver supports FD */ + if (priv->ctrlmode & CAN_CTRLMODE_FD) + dev->mtu = CANFD_MTU; + else + dev->mtu = CAN_MTU; + } + if (data[IFLA_CAN_RESTART_MS]) { /* Do not allow changing restart delay while running */ if (dev->flags & IFF_UP) @@ -696,22 +758,48 @@ static int can_changelink(struct net_device *dev, return err; } + if (data[IFLA_CAN_DATA_BITTIMING]) { + struct can_bittiming dbt; + + /* Do not allow changing bittiming while running */ + if (dev->flags & IFF_UP) + return -EBUSY; + memcpy(&dbt, nla_data(data[IFLA_CAN_DATA_BITTIMING]), + sizeof(dbt)); + err = can_get_bittiming(dev, &dbt, priv->data_bittiming_const); + if (err) + return err; + memcpy(&priv->data_bittiming, &dbt, sizeof(dbt)); + + if (priv->do_set_data_bittiming) { + /* Finally, set the bit-timing registers */ + err = priv->do_set_data_bittiming(dev); + if (err) + return err; + } + } + return 0; } static size_t can_get_size(const struct net_device *dev) { struct can_priv *priv = netdev_priv(dev); - size_t size; - - size = nla_total_size(sizeof(u32)); /* IFLA_CAN_STATE */ - size += nla_total_size(sizeof(struct can_ctrlmode)); /* IFLA_CAN_CTRLMODE */ - size += nla_total_size(sizeof(u32)); /* IFLA_CAN_RESTART_MS */ - size += nla_total_size(sizeof(struct can_bittiming)); /* IFLA_CAN_BITTIMING */ - size += nla_total_size(sizeof(struct can_clock)); /* IFLA_CAN_CLOCK */ - if (priv->do_get_berr_counter) /* IFLA_CAN_BERR_COUNTER */ + size_t size = 0; + + if (priv->bittiming.bitrate) /* IFLA_CAN_BITTIMING */ + size += nla_total_size(sizeof(struct can_bittiming)); + if (priv->bittiming_const) /* IFLA_CAN_BITTIMING_CONST */ + size += nla_total_size(sizeof(struct can_bittiming_const)); + size += nla_total_size(sizeof(struct can_clock)); /* IFLA_CAN_CLOCK */ + size += nla_total_size(sizeof(u32)); /* IFLA_CAN_STATE */ + size += nla_total_size(sizeof(struct can_ctrlmode)); /* IFLA_CAN_CTRLMODE */ + size += nla_total_size(sizeof(u32)); /* IFLA_CAN_RESTART_MS */ + if (priv->do_get_berr_counter) /* IFLA_CAN_BERR_COUNTER */ size += nla_total_size(sizeof(struct can_berr_counter)); - if (priv->bittiming_const) /* IFLA_CAN_BITTIMING_CONST */ + if (priv->data_bittiming.bitrate) /* IFLA_CAN_DATA_BITTIMING */ + size += nla_total_size(sizeof(struct can_bittiming)); + if (priv->data_bittiming_const) /* IFLA_CAN_DATA_BITTIMING_CONST */ size += nla_total_size(sizeof(struct can_bittiming_const)); return size; @@ -726,23 +814,35 @@ static int can_fill_info(struct sk_buff *skb, const struct net_device *dev) if (priv->do_get_state) priv->do_get_state(dev, &state); - if (nla_put_u32(skb, IFLA_CAN_STATE, state) || + + if ((priv->bittiming.bitrate && + nla_put(skb, IFLA_CAN_BITTIMING, + sizeof(priv->bittiming), &priv->bittiming)) || + + (priv->bittiming_const && + nla_put(skb, IFLA_CAN_BITTIMING_CONST, + sizeof(*priv->bittiming_const), priv->bittiming_const)) || + + nla_put(skb, IFLA_CAN_CLOCK, sizeof(cm), &priv->clock) || + nla_put_u32(skb, IFLA_CAN_STATE, state) || nla_put(skb, IFLA_CAN_CTRLMODE, sizeof(cm), &cm) || nla_put_u32(skb, IFLA_CAN_RESTART_MS, priv->restart_ms) || - nla_put(skb, IFLA_CAN_BITTIMING, - sizeof(priv->bittiming), &priv->bittiming) || - nla_put(skb, IFLA_CAN_CLOCK, sizeof(cm), &priv->clock) || + (priv->do_get_berr_counter && !priv->do_get_berr_counter(dev, &bec) && nla_put(skb, IFLA_CAN_BERR_COUNTER, sizeof(bec), &bec)) || - (priv->bittiming_const && - nla_put(skb, IFLA_CAN_BITTIMING_CONST, - sizeof(*priv->bittiming_const), priv->bittiming_const))) - goto nla_put_failure; - return 0; -nla_put_failure: - return -EMSGSIZE; + (priv->data_bittiming.bitrate && + nla_put(skb, IFLA_CAN_DATA_BITTIMING, + sizeof(priv->data_bittiming), &priv->data_bittiming)) || + + (priv->data_bittiming_const && + nla_put(skb, IFLA_CAN_DATA_BITTIMING_CONST, + sizeof(*priv->data_bittiming_const), + priv->data_bittiming_const))) + return -EMSGSIZE; + + return 0; } static size_t can_get_xstats_size(const struct net_device *dev) diff --git a/drivers/net/can/flexcan.c b/drivers/net/can/flexcan.c index 3f21142138b..f425ec2c783 100644 --- a/drivers/net/can/flexcan.c +++ b/drivers/net/can/flexcan.c @@ -62,7 +62,7 @@ #define FLEXCAN_MCR_BCC BIT(16) #define FLEXCAN_MCR_LPRIO_EN BIT(13) #define FLEXCAN_MCR_AEN BIT(12) -#define FLEXCAN_MCR_MAXMB(x) ((x) & 0xf) +#define FLEXCAN_MCR_MAXMB(x) ((x) & 0x1f) #define FLEXCAN_MCR_IDAM_A (0 << 8) #define FLEXCAN_MCR_IDAM_B (1 << 8) #define FLEXCAN_MCR_IDAM_C (2 << 8) @@ -144,6 +144,8 @@ #define FLEXCAN_MB_CODE_MASK (0xf0ffffff) +#define FLEXCAN_TIMEOUT_US (50) + /* * FLEXCAN hardware feature flags * @@ -235,9 +237,12 @@ static const struct can_bittiming_const flexcan_bittiming_const = { }; /* - * Abstract off the read/write for arm versus ppc. + * Abstract off the read/write for arm versus ppc. This + * assumes that PPC uses big-endian registers and everything + * else uses little-endian registers, independent of CPU + * endianess. */ -#if defined(__BIG_ENDIAN) +#if defined(CONFIG_PPC) static inline u32 flexcan_read(void __iomem *addr) { return in_be32(addr); @@ -259,6 +264,22 @@ static inline void flexcan_write(u32 val, void __iomem *addr) } #endif +static inline int flexcan_transceiver_enable(const struct flexcan_priv *priv) +{ + if (!priv->reg_xceiver) + return 0; + + return regulator_enable(priv->reg_xceiver); +} + +static inline int flexcan_transceiver_disable(const struct flexcan_priv *priv) +{ + if (!priv->reg_xceiver) + return 0; + + return regulator_disable(priv->reg_xceiver); +} + static inline int flexcan_has_and_handle_berr(const struct flexcan_priv *priv, u32 reg_esr) { @@ -266,26 +287,95 @@ static inline int flexcan_has_and_handle_berr(const struct flexcan_priv *priv, (reg_esr & FLEXCAN_ESR_ERR_BUS); } -static inline void flexcan_chip_enable(struct flexcan_priv *priv) +static int flexcan_chip_enable(struct flexcan_priv *priv) { struct flexcan_regs __iomem *regs = priv->base; + unsigned int timeout = FLEXCAN_TIMEOUT_US / 10; u32 reg; reg = flexcan_read(®s->mcr); reg &= ~FLEXCAN_MCR_MDIS; flexcan_write(reg, ®s->mcr); - udelay(10); + while (timeout-- && (flexcan_read(®s->mcr) & FLEXCAN_MCR_LPM_ACK)) + usleep_range(10, 20); + + if (flexcan_read(®s->mcr) & FLEXCAN_MCR_LPM_ACK) + return -ETIMEDOUT; + + return 0; } -static inline void flexcan_chip_disable(struct flexcan_priv *priv) +static int flexcan_chip_disable(struct flexcan_priv *priv) { struct flexcan_regs __iomem *regs = priv->base; + unsigned int timeout = FLEXCAN_TIMEOUT_US / 10; u32 reg; reg = flexcan_read(®s->mcr); reg |= FLEXCAN_MCR_MDIS; flexcan_write(reg, ®s->mcr); + + while (timeout-- && !(flexcan_read(®s->mcr) & FLEXCAN_MCR_LPM_ACK)) + usleep_range(10, 20); + + if (!(flexcan_read(®s->mcr) & FLEXCAN_MCR_LPM_ACK)) + return -ETIMEDOUT; + + return 0; +} + +static int flexcan_chip_freeze(struct flexcan_priv *priv) +{ + struct flexcan_regs __iomem *regs = priv->base; + unsigned int timeout = 1000 * 1000 * 10 / priv->can.bittiming.bitrate; + u32 reg; + + reg = flexcan_read(®s->mcr); + reg |= FLEXCAN_MCR_HALT; + flexcan_write(reg, ®s->mcr); + + while (timeout-- && !(flexcan_read(®s->mcr) & FLEXCAN_MCR_FRZ_ACK)) + usleep_range(100, 200); + + if (!(flexcan_read(®s->mcr) & FLEXCAN_MCR_FRZ_ACK)) + return -ETIMEDOUT; + + return 0; +} + +static int flexcan_chip_unfreeze(struct flexcan_priv *priv) +{ + struct flexcan_regs __iomem *regs = priv->base; + unsigned int timeout = FLEXCAN_TIMEOUT_US / 10; + u32 reg; + + reg = flexcan_read(®s->mcr); + reg &= ~FLEXCAN_MCR_HALT; + flexcan_write(reg, ®s->mcr); + + while (timeout-- && (flexcan_read(®s->mcr) & FLEXCAN_MCR_FRZ_ACK)) + usleep_range(10, 20); + + if (flexcan_read(®s->mcr) & FLEXCAN_MCR_FRZ_ACK) + return -ETIMEDOUT; + + return 0; +} + +static int flexcan_chip_softreset(struct flexcan_priv *priv) +{ + struct flexcan_regs __iomem *regs = priv->base; + unsigned int timeout = FLEXCAN_TIMEOUT_US / 10; + + flexcan_write(FLEXCAN_MCR_SOFTRST, ®s->mcr); + while (timeout-- && (flexcan_read(®s->mcr) & FLEXCAN_MCR_SOFTRST)) + usleep_range(10, 20); + + if (flexcan_read(®s->mcr) & FLEXCAN_MCR_SOFTRST) + return -ETIMEDOUT; + + return 0; } static int flexcan_get_berr_counter(const struct net_device *dev, @@ -706,19 +796,14 @@ static int flexcan_chip_start(struct net_device *dev) u32 reg_mcr, reg_ctrl; /* enable module */ - flexcan_chip_enable(priv); + err = flexcan_chip_enable(priv); + if (err) + return err; /* soft reset */ - flexcan_write(FLEXCAN_MCR_SOFTRST, ®s->mcr); - udelay(10); - - reg_mcr = flexcan_read(®s->mcr); - if (reg_mcr & FLEXCAN_MCR_SOFTRST) { - netdev_err(dev, "Failed to softreset can module (mcr=0x%08x)\n", - reg_mcr); - err = -ENODEV; - goto out; - } + err = flexcan_chip_softreset(priv); + if (err) + goto out_chip_disable; flexcan_set_bittiming(dev); @@ -735,9 +820,11 @@ static int flexcan_chip_start(struct net_device *dev) * */ reg_mcr = flexcan_read(®s->mcr); + reg_mcr &= ~FLEXCAN_MCR_MAXMB(0xff); reg_mcr |= FLEXCAN_MCR_FRZ | FLEXCAN_MCR_FEN | FLEXCAN_MCR_HALT | FLEXCAN_MCR_SUPV | FLEXCAN_MCR_WRN_EN | - FLEXCAN_MCR_IDAM_C | FLEXCAN_MCR_SRX_DIS; + FLEXCAN_MCR_IDAM_C | FLEXCAN_MCR_SRX_DIS | + FLEXCAN_MCR_MAXMB(FLEXCAN_TX_BUF_ID); netdev_dbg(dev, "%s: writing mcr=0x%08x", __func__, reg_mcr); flexcan_write(reg_mcr, ®s->mcr); @@ -771,6 +858,10 @@ static int flexcan_chip_start(struct net_device *dev) netdev_dbg(dev, "%s: writing ctrl=0x%08x", __func__, reg_ctrl); flexcan_write(reg_ctrl, ®s->ctrl); + /* Abort any pending TX, mark Mailbox as INACTIVE */ + flexcan_write(FLEXCAN_MB_CNT_CODE(0x4), + ®s->cantxfg[FLEXCAN_TX_BUF_ID].can_ctrl); + /* acceptance mask/acceptance code (accept everything) */ flexcan_write(0x0, ®s->rxgmask); flexcan_write(0x0, ®s->rx14mask); @@ -779,16 +870,14 @@ static int flexcan_chip_start(struct net_device *dev) if (priv->devtype_data->features & FLEXCAN_HAS_V10_FEATURES) flexcan_write(0x0, ®s->rxfgmask); - if (priv->reg_xceiver) { - err = regulator_enable(priv->reg_xceiver); - if (err) - goto out; - } + err = flexcan_transceiver_enable(priv); + if (err) + goto out_chip_disable; /* synchronize with the can bus */ - reg_mcr = flexcan_read(®s->mcr); - reg_mcr &= ~FLEXCAN_MCR_HALT; - flexcan_write(reg_mcr, ®s->mcr); + err = flexcan_chip_unfreeze(priv); + if (err) + goto out_transceiver_disable; priv->can.state = CAN_STATE_ERROR_ACTIVE; @@ -801,7 +890,9 @@ static int flexcan_chip_start(struct net_device *dev) return 0; - out: + out_transceiver_disable: + flexcan_transceiver_disable(priv); + out_chip_disable: flexcan_chip_disable(priv); return err; } @@ -816,18 +907,17 @@ static void flexcan_chip_stop(struct net_device *dev) { struct flexcan_priv *priv = netdev_priv(dev); struct flexcan_regs __iomem *regs = priv->base; - u32 reg; + + /* freeze + disable module */ + flexcan_chip_freeze(priv); + flexcan_chip_disable(priv); /* Disable all interrupts */ flexcan_write(0, ®s->imask1); + flexcan_write(priv->reg_ctrl_default & ~FLEXCAN_CTRL_ERR_ALL, + ®s->ctrl); - /* Disable + halt module */ - reg = flexcan_read(®s->mcr); - reg |= FLEXCAN_MCR_MDIS | FLEXCAN_MCR_HALT; - flexcan_write(reg, ®s->mcr); - - if (priv->reg_xceiver) - regulator_disable(priv->reg_xceiver); + flexcan_transceiver_disable(priv); priv->can.state = CAN_STATE_STOPPED; return; @@ -857,7 +947,7 @@ static int flexcan_open(struct net_device *dev) /* start chip and queuing */ err = flexcan_chip_start(dev); if (err) - goto out_close; + goto out_free_irq; can_led_event(dev, CAN_LED_EVENT_OPEN); @@ -866,6 +956,8 @@ static int flexcan_open(struct net_device *dev) return 0; + out_free_irq: + free_irq(dev->irq, dev); out_close: close_candev(dev); out_disable_per: @@ -919,6 +1011,7 @@ static const struct net_device_ops flexcan_netdev_ops = { .ndo_open = flexcan_open, .ndo_stop = flexcan_close, .ndo_start_xmit = flexcan_start_xmit, + .ndo_change_mtu = can_change_mtu, }; static int register_flexcandev(struct net_device *dev) @@ -936,12 +1029,16 @@ static int register_flexcandev(struct net_device *dev) goto out_disable_ipg; /* select "bus clock", chip must be disabled */ - flexcan_chip_disable(priv); + err = flexcan_chip_disable(priv); + if (err) + goto out_disable_per; reg = flexcan_read(®s->ctrl); reg |= FLEXCAN_CTRL_CLK_SRC; flexcan_write(reg, ®s->ctrl); - flexcan_chip_enable(priv); + err = flexcan_chip_enable(priv); + if (err) + goto out_chip_disable; /* set freeze, halt and activate FIFO, restrict register access */ reg = flexcan_read(®s->mcr); @@ -958,14 +1055,15 @@ static int register_flexcandev(struct net_device *dev) if (!(reg & FLEXCAN_MCR_FEN)) { netdev_err(dev, "Could not enable RX FIFO, unsupported core\n"); err = -ENODEV; - goto out_disable_per; + goto out_chip_disable; } err = register_candev(dev); - out_disable_per: /* disable core and turn off clocks */ + out_chip_disable: flexcan_chip_disable(priv); + out_disable_per: clk_disable_unprepare(priv->clk_per); out_disable_ipg: clk_disable_unprepare(priv->clk_ipg); @@ -979,9 +1077,9 @@ static void unregister_flexcandev(struct net_device *dev) } static const struct of_device_id flexcan_of_match[] = { - { .compatible = "fsl,p1010-flexcan", .data = &fsl_p1010_devtype_data, }, - { .compatible = "fsl,imx28-flexcan", .data = &fsl_imx28_devtype_data, }, { .compatible = "fsl,imx6q-flexcan", .data = &fsl_imx6q_devtype_data, }, + { .compatible = "fsl,imx28-flexcan", .data = &fsl_imx28_devtype_data, }, + { .compatible = "fsl,p1010-flexcan", .data = &fsl_p1010_devtype_data, }, { /* sentinel */ }, }; MODULE_DEVICE_TABLE(of, flexcan_of_match); @@ -1014,13 +1112,13 @@ static int flexcan_probe(struct platform_device *pdev) dev_err(&pdev->dev, "no ipg clock defined\n"); return PTR_ERR(clk_ipg); } - clock_freq = clk_get_rate(clk_ipg); clk_per = devm_clk_get(&pdev->dev, "per"); if (IS_ERR(clk_per)) { dev_err(&pdev->dev, "no per clock defined\n"); return PTR_ERR(clk_per); } + clock_freq = clk_get_rate(clk_per); } mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); @@ -1035,9 +1133,9 @@ static int flexcan_probe(struct platform_device *pdev) of_id = of_match_device(flexcan_of_match, &pdev->dev); if (of_id) { devtype_data = of_id->data; - } else if (pdev->id_entry->driver_data) { + } else if (platform_get_device_id(pdev)->driver_data) { devtype_data = (struct flexcan_devtype_data *) - pdev->id_entry->driver_data; + platform_get_device_id(pdev)->driver_data; } else { return -ENODEV; } @@ -1062,7 +1160,7 @@ static int flexcan_probe(struct platform_device *pdev) priv->dev = dev; priv->clk_ipg = clk_ipg; priv->clk_per = clk_per; - priv->pdata = pdev->dev.platform_data; + priv->pdata = dev_get_platdata(&pdev->dev); priv->devtype_data = devtype_data; priv->reg_xceiver = devm_regulator_get(&pdev->dev, "xceiver"); @@ -1095,21 +1193,24 @@ static int flexcan_probe(struct platform_device *pdev) static int flexcan_remove(struct platform_device *pdev) { struct net_device *dev = platform_get_drvdata(pdev); + struct flexcan_priv *priv = netdev_priv(dev); unregister_flexcandev(dev); - + netif_napi_del(&priv->napi); free_candev(dev); return 0; } -#ifdef CONFIG_PM_SLEEP -static int flexcan_suspend(struct device *device) +static int __maybe_unused flexcan_suspend(struct device *device) { struct net_device *dev = dev_get_drvdata(device); struct flexcan_priv *priv = netdev_priv(dev); + int err; - flexcan_chip_disable(priv); + err = flexcan_chip_disable(priv); + if (err) + return err; if (netif_running(dev)) { netif_stop_queue(dev); @@ -1120,7 +1221,7 @@ static int flexcan_suspend(struct device *device) return 0; } -static int flexcan_resume(struct device *device) +static int __maybe_unused flexcan_resume(struct device *device) { struct net_device *dev = dev_get_drvdata(device); struct flexcan_priv *priv = netdev_priv(dev); @@ -1130,11 +1231,8 @@ static int flexcan_resume(struct device *device) netif_device_attach(dev); netif_start_queue(dev); } - flexcan_chip_enable(priv); - - return 0; + return flexcan_chip_enable(priv); } -#endif /* CONFIG_PM_SLEEP */ static SIMPLE_DEV_PM_OPS(flexcan_pm_ops, flexcan_suspend, flexcan_resume); diff --git a/drivers/net/can/grcan.c b/drivers/net/can/grcan.c index 6aa737a2439..3fd9fd942c6 100644 --- a/drivers/net/can/grcan.c +++ b/drivers/net/can/grcan.c @@ -34,10 +34,7 @@ #include <linux/io.h> #include <linux/can/dev.h> #include <linux/spinlock.h> - #include <linux/of_platform.h> -#include <asm/prom.h> - #include <linux/of_irq.h> #include <linux/dma-mapping.h> @@ -1581,6 +1578,7 @@ static const struct net_device_ops grcan_netdev_ops = { .ndo_open = grcan_open, .ndo_stop = grcan_close, .ndo_start_xmit = grcan_start_xmit, + .ndo_change_mtu = can_change_mtu, }; static int grcan_setup_netdev(struct platform_device *ofdev, diff --git a/drivers/net/can/janz-ican3.c b/drivers/net/can/janz-ican3.c index 36bd6fa1c7f..2382c04dc78 100644 --- a/drivers/net/can/janz-ican3.c +++ b/drivers/net/can/janz-ican3.c @@ -11,7 +11,6 @@ #include <linux/kernel.h> #include <linux/module.h> -#include <linux/init.h> #include <linux/interrupt.h> #include <linux/delay.h> #include <linux/platform_device.h> @@ -19,6 +18,7 @@ #include <linux/netdevice.h> #include <linux/can.h> #include <linux/can/dev.h> +#include <linux/can/skb.h> #include <linux/can/error.h> #include <linux/mfd/janz.h> @@ -198,9 +198,6 @@ struct ican3_dev { struct net_device *ndev; struct napi_struct napi; - /* Device for printing */ - struct device *dev; - /* module number */ unsigned int num; @@ -295,7 +292,7 @@ static int ican3_old_recv_msg(struct ican3_dev *mod, struct ican3_msg *msg) xord = locl ^ peer; if ((xord & MSYNC_RB_MASK) == 0x00) { - dev_dbg(mod->dev, "no mbox for reading\n"); + netdev_dbg(mod->ndev, "no mbox for reading\n"); return -ENOMEM; } @@ -340,7 +337,7 @@ static int ican3_old_send_msg(struct ican3_dev *mod, struct ican3_msg *msg) xord = locl ^ peer; if ((xord & MSYNC_WB_MASK) == MSYNC_WB_MASK) { - dev_err(mod->dev, "no mbox for writing\n"); + netdev_err(mod->ndev, "no mbox for writing\n"); return -ENOMEM; } @@ -542,7 +539,7 @@ static int ican3_new_send_msg(struct ican3_dev *mod, struct ican3_msg *msg) memcpy_fromio(&desc, desc_addr, sizeof(desc)); if (!(desc.control & DESC_VALID)) { - dev_dbg(mod->dev, "%s: no free buffers\n", __func__); + netdev_dbg(mod->ndev, "%s: no free buffers\n", __func__); return -ENOMEM; } @@ -573,7 +570,7 @@ static int ican3_new_recv_msg(struct ican3_dev *mod, struct ican3_msg *msg) memcpy_fromio(&desc, desc_addr, sizeof(desc)); if (!(desc.control & DESC_VALID)) { - dev_dbg(mod->dev, "%s: no buffers to recv\n", __func__); + netdev_dbg(mod->ndev, "%s: no buffers to recv\n", __func__); return -ENOMEM; } @@ -883,7 +880,7 @@ static void can_frame_to_ican3(struct ican3_dev *mod, */ static void ican3_handle_idvers(struct ican3_dev *mod, struct ican3_msg *msg) { - dev_dbg(mod->dev, "IDVERS response: %s\n", msg->data); + netdev_dbg(mod->ndev, "IDVERS response: %s\n", msg->data); } static void ican3_handle_msglost(struct ican3_dev *mod, struct ican3_msg *msg) @@ -899,7 +896,7 @@ static void ican3_handle_msglost(struct ican3_dev *mod, struct ican3_msg *msg) * error frame for userspace */ if (msg->spec == MSG_MSGLOST) { - dev_err(mod->dev, "lost %d control messages\n", msg->data[0]); + netdev_err(mod->ndev, "lost %d control messages\n", msg->data[0]); return; } @@ -939,13 +936,13 @@ static int ican3_handle_cevtind(struct ican3_dev *mod, struct ican3_msg *msg) /* we can only handle the SJA1000 part */ if (msg->data[1] != CEVTIND_CHIP_SJA1000) { - dev_err(mod->dev, "unable to handle errors on non-SJA1000\n"); + netdev_err(mod->ndev, "unable to handle errors on non-SJA1000\n"); return -ENODEV; } /* check the message length for sanity */ if (le16_to_cpu(msg->len) < 6) { - dev_err(mod->dev, "error message too short\n"); + netdev_err(mod->ndev, "error message too short\n"); return -EINVAL; } @@ -967,7 +964,7 @@ static int ican3_handle_cevtind(struct ican3_dev *mod, struct ican3_msg *msg) */ if (isrc == CEVTIND_BEI) { int ret; - dev_dbg(mod->dev, "bus error interrupt\n"); + netdev_dbg(mod->ndev, "bus error interrupt\n"); /* TX error */ if (!(ecc & ECC_DIR)) { @@ -983,7 +980,7 @@ static int ican3_handle_cevtind(struct ican3_dev *mod, struct ican3_msg *msg) */ ret = ican3_set_buserror(mod, 1); if (ret) { - dev_err(mod->dev, "unable to re-enable bus-error\n"); + netdev_err(mod->ndev, "unable to re-enable bus-error\n"); return ret; } @@ -998,7 +995,7 @@ static int ican3_handle_cevtind(struct ican3_dev *mod, struct ican3_msg *msg) /* data overrun interrupt */ if (isrc == CEVTIND_DOI || isrc == CEVTIND_LOST) { - dev_dbg(mod->dev, "data overrun interrupt\n"); + netdev_dbg(mod->ndev, "data overrun interrupt\n"); cf->can_id |= CAN_ERR_CRTL; cf->data[1] = CAN_ERR_CRTL_RX_OVERFLOW; stats->rx_over_errors++; @@ -1007,7 +1004,7 @@ static int ican3_handle_cevtind(struct ican3_dev *mod, struct ican3_msg *msg) /* error warning + passive interrupt */ if (isrc == CEVTIND_EI) { - dev_dbg(mod->dev, "error warning + passive interrupt\n"); + netdev_dbg(mod->ndev, "error warning + passive interrupt\n"); if (status & SR_BS) { state = CAN_STATE_BUS_OFF; cf->can_id |= CAN_ERR_BUSOFF; @@ -1088,7 +1085,7 @@ static void ican3_handle_inquiry(struct ican3_dev *mod, struct ican3_msg *msg) complete(&mod->termination_comp); break; default: - dev_err(mod->dev, "received an unknown inquiry response\n"); + netdev_err(mod->ndev, "received an unknown inquiry response\n"); break; } } @@ -1096,7 +1093,7 @@ static void ican3_handle_inquiry(struct ican3_dev *mod, struct ican3_msg *msg) static void ican3_handle_unknown_message(struct ican3_dev *mod, struct ican3_msg *msg) { - dev_warn(mod->dev, "received unknown message: spec 0x%.2x length %d\n", + netdev_warn(mod->ndev, "received unknown message: spec 0x%.2x length %d\n", msg->spec, le16_to_cpu(msg->len)); } @@ -1105,7 +1102,7 @@ static void ican3_handle_unknown_message(struct ican3_dev *mod, */ static void ican3_handle_message(struct ican3_dev *mod, struct ican3_msg *msg) { - dev_dbg(mod->dev, "%s: modno %d spec 0x%.2x len %d bytes\n", __func__, + netdev_dbg(mod->ndev, "%s: modno %d spec 0x%.2x len %d bytes\n", __func__, mod->num, msg->spec, le16_to_cpu(msg->len)); switch (msg->spec) { @@ -1134,20 +1131,9 @@ static void ican3_handle_message(struct ican3_dev *mod, struct ican3_msg *msg) */ static void ican3_put_echo_skb(struct ican3_dev *mod, struct sk_buff *skb) { - struct sock *srcsk = skb->sk; - - if (atomic_read(&skb->users) != 1) { - struct sk_buff *old_skb = skb; - - skb = skb_clone(old_skb, GFP_ATOMIC); - kfree_skb(old_skb); - if (!skb) - return; - } else { - skb_orphan(skb); - } - - skb->sk = srcsk; + skb = can_create_echo_skb(skb); + if (!skb) + return; /* save this skb for tx interrupt echo handling */ skb_queue_tail(&mod->echoq, skb); @@ -1323,7 +1309,7 @@ static int ican3_napi(struct napi_struct *napi, int budget) /* process all communication messages */ while (true) { - struct ican3_msg msg; + struct ican3_msg uninitialized_var(msg); ret = ican3_recv_msg(mod, &msg); if (ret) break; @@ -1417,7 +1403,7 @@ static int ican3_reset_module(struct ican3_dev *mod) msleep(10); } while (time_before(jiffies, start + HZ / 4)); - dev_err(mod->dev, "failed to reset CAN module\n"); + netdev_err(mod->ndev, "failed to reset CAN module\n"); return -ETIMEDOUT; } @@ -1436,7 +1422,7 @@ static int ican3_startup_module(struct ican3_dev *mod) ret = ican3_reset_module(mod); if (ret) { - dev_err(mod->dev, "unable to reset module\n"); + netdev_err(mod->ndev, "unable to reset module\n"); return ret; } @@ -1445,41 +1431,41 @@ static int ican3_startup_module(struct ican3_dev *mod) ret = ican3_msg_connect(mod); if (ret) { - dev_err(mod->dev, "unable to connect to module\n"); + netdev_err(mod->ndev, "unable to connect to module\n"); return ret; } ican3_init_new_host_interface(mod); ret = ican3_msg_newhostif(mod); if (ret) { - dev_err(mod->dev, "unable to switch to new-style interface\n"); + netdev_err(mod->ndev, "unable to switch to new-style interface\n"); return ret; } /* default to "termination on" */ ret = ican3_set_termination(mod, true); if (ret) { - dev_err(mod->dev, "unable to enable termination\n"); + netdev_err(mod->ndev, "unable to enable termination\n"); return ret; } /* default to "bus errors enabled" */ ret = ican3_set_buserror(mod, 1); if (ret) { - dev_err(mod->dev, "unable to set bus-error\n"); + netdev_err(mod->ndev, "unable to set bus-error\n"); return ret; } ican3_init_fast_host_interface(mod); ret = ican3_msg_fasthostif(mod); if (ret) { - dev_err(mod->dev, "unable to switch to fast host interface\n"); + netdev_err(mod->ndev, "unable to switch to fast host interface\n"); return ret; } ret = ican3_set_id_filter(mod, true); if (ret) { - dev_err(mod->dev, "unable to set acceptance filter\n"); + netdev_err(mod->ndev, "unable to set acceptance filter\n"); return ret; } @@ -1498,14 +1484,14 @@ static int ican3_open(struct net_device *ndev) /* open the CAN layer */ ret = open_candev(ndev); if (ret) { - dev_err(mod->dev, "unable to start CAN layer\n"); + netdev_err(mod->ndev, "unable to start CAN layer\n"); return ret; } /* bring the bus online */ ret = ican3_set_bus_state(mod, true); if (ret) { - dev_err(mod->dev, "unable to set bus-on\n"); + netdev_err(mod->ndev, "unable to set bus-on\n"); close_candev(ndev); return ret; } @@ -1529,7 +1515,7 @@ static int ican3_stop(struct net_device *ndev) /* bring the bus offline, stop receiving packets */ ret = ican3_set_bus_state(mod, false); if (ret) { - dev_err(mod->dev, "unable to set bus-off\n"); + netdev_err(mod->ndev, "unable to set bus-off\n"); return ret; } @@ -1556,7 +1542,7 @@ static int ican3_xmit(struct sk_buff *skb, struct net_device *ndev) /* check that we can actually transmit */ if (!ican3_txok(mod)) { - dev_err(mod->dev, "BUG: no free descriptors\n"); + netdev_err(mod->ndev, "BUG: no free descriptors\n"); spin_unlock_irqrestore(&mod->lock, flags); return NETDEV_TX_BUSY; } @@ -1608,6 +1594,7 @@ static const struct net_device_ops ican3_netdev_ops = { .ndo_open = ican3_open, .ndo_stop = ican3_stop, .ndo_start_xmit = ican3_xmit, + .ndo_change_mtu = can_change_mtu, }; /* @@ -1668,7 +1655,7 @@ static int ican3_set_mode(struct net_device *ndev, enum can_mode mode) /* bring the bus online */ ret = ican3_set_bus_state(mod, true); if (ret) { - dev_err(mod->dev, "unable to set bus-on\n"); + netdev_err(ndev, "unable to set bus-on\n"); return ret; } @@ -1693,7 +1680,7 @@ static int ican3_get_berr_counter(const struct net_device *ndev, ret = wait_for_completion_timeout(&mod->buserror_comp, HZ); if (ret == 0) { - dev_info(mod->dev, "%s timed out\n", __func__); + netdev_info(mod->ndev, "%s timed out\n", __func__); return -ETIMEDOUT; } @@ -1719,7 +1706,7 @@ static ssize_t ican3_sysfs_show_term(struct device *dev, ret = wait_for_completion_timeout(&mod->termination_comp, HZ); if (ret == 0) { - dev_info(mod->dev, "%s timed out\n", __func__); + netdev_info(mod->ndev, "%s timed out\n", __func__); return -ETIMEDOUT; } @@ -1769,7 +1756,7 @@ static int ican3_probe(struct platform_device *pdev) struct device *dev; int ret; - pdata = pdev->dev.platform_data; + pdata = dev_get_platdata(&pdev->dev); if (!pdata) return -ENXIO; @@ -1789,7 +1776,6 @@ static int ican3_probe(struct platform_device *pdev) platform_set_drvdata(pdev, ndev); mod = netdev_priv(ndev); mod->ndev = ndev; - mod->dev = &pdev->dev; mod->num = pdata->modno; netif_napi_add(ndev, &mod->napi, ican3_napi, ICAN3_RX_BUFFERS); skb_queue_head_init(&mod->echoq); diff --git a/drivers/net/can/led.c b/drivers/net/can/led.c index a3d99a8fd2d..ab7f1b01be4 100644 --- a/drivers/net/can/led.c +++ b/drivers/net/can/led.c @@ -97,6 +97,9 @@ static int can_led_notifier(struct notifier_block *nb, unsigned long msg, if (!priv) return NOTIFY_DONE; + if (!priv->tx_led_trig || !priv->rx_led_trig) + return NOTIFY_DONE; + if (msg == NETDEV_CHANGENAME) { snprintf(name, sizeof(name), "%s-tx", netdev->name); led_trigger_rename_static(name, priv->tx_led_trig); diff --git a/drivers/net/can/mscan/Kconfig b/drivers/net/can/mscan/Kconfig index f19be5269e7..81c71171949 100644 --- a/drivers/net/can/mscan/Kconfig +++ b/drivers/net/can/mscan/Kconfig @@ -1,5 +1,5 @@ config CAN_MSCAN - depends on PPC || M68K + depends on PPC tristate "Support for Freescale MSCAN based chips" ---help--- The Motorola Scalable Controller Area Network (MSCAN) definition diff --git a/drivers/net/can/mscan/mpc5xxx_can.c b/drivers/net/can/mscan/mpc5xxx_can.c index e59b3a392af..44725296f72 100644 --- a/drivers/net/can/mscan/mpc5xxx_can.c +++ b/drivers/net/can/mscan/mpc5xxx_can.c @@ -16,8 +16,7 @@ * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * along with this program; if not, see <http://www.gnu.org/licenses/>. */ #include <linux/kernel.h> @@ -109,135 +108,170 @@ static u32 mpc52xx_can_get_clock(struct platform_device *ofdev, #endif /* CONFIG_PPC_MPC52xx */ #ifdef CONFIG_PPC_MPC512x -struct mpc512x_clockctl { - u32 spmr; /* System PLL Mode Reg */ - u32 sccr[2]; /* System Clk Ctrl Reg 1 & 2 */ - u32 scfr1; /* System Clk Freq Reg 1 */ - u32 scfr2; /* System Clk Freq Reg 2 */ - u32 reserved; - u32 bcr; /* Bread Crumb Reg */ - u32 pccr[12]; /* PSC Clk Ctrl Reg 0-11 */ - u32 spccr; /* SPDIF Clk Ctrl Reg */ - u32 cccr; /* CFM Clk Ctrl Reg */ - u32 dccr; /* DIU Clk Cnfg Reg */ - u32 mccr[4]; /* MSCAN Clk Ctrl Reg 1-3 */ -}; - -static struct of_device_id mpc512x_clock_ids[] = { - { .compatible = "fsl,mpc5121-clock", }, - {} -}; - static u32 mpc512x_can_get_clock(struct platform_device *ofdev, - const char *clock_name, int *mscan_clksrc) + const char *clock_source, int *mscan_clksrc) { - struct mpc512x_clockctl __iomem *clockctl; - struct device_node *np_clock; - struct clk *sys_clk, *ref_clk; - int plen, clockidx, clocksrc = -1; - u32 sys_freq, val, clockdiv = 1, freq = 0; - const u32 *pval; - - np_clock = of_find_matching_node(NULL, mpc512x_clock_ids); - if (!np_clock) { - dev_err(&ofdev->dev, "couldn't find clock node\n"); - return 0; - } - clockctl = of_iomap(np_clock, 0); - if (!clockctl) { - dev_err(&ofdev->dev, "couldn't map clock registers\n"); - goto exit_put; - } + struct device_node *np; + u32 clockdiv; + enum { + CLK_FROM_AUTO, + CLK_FROM_IPS, + CLK_FROM_SYS, + CLK_FROM_REF, + } clk_from; + struct clk *clk_in, *clk_can; + unsigned long freq_calc; + struct mscan_priv *priv; + struct clk *clk_ipg; - /* Determine the MSCAN device index from the peripheral's - * physical address. Register address offsets against the - * IMMR base are: 0x1300, 0x1380, 0x2300, 0x2380 + /* the caller passed in the clock source spec that was read from + * the device tree, get the optional clock divider as well */ - pval = of_get_property(ofdev->dev.of_node, "reg", &plen); - BUG_ON(!pval || plen < sizeof(*pval)); - clockidx = (*pval & 0x80) ? 1 : 0; - if (*pval & 0x2000) - clockidx += 2; + np = ofdev->dev.of_node; + clockdiv = 1; + of_property_read_u32(np, "fsl,mscan-clock-divider", &clockdiv); + dev_dbg(&ofdev->dev, "device tree specs: clk src[%s] div[%d]\n", + clock_source ? clock_source : "<NULL>", clockdiv); + + /* when clock-source is 'ip', the CANCTL1[CLKSRC] bit needs to + * get set, and the 'ips' clock is the input to the MSCAN + * component + * + * for clock-source values of 'ref' or 'sys' the CANCTL1[CLKSRC] + * bit needs to get cleared, an optional clock-divider may have + * been specified (the default value is 1), the appropriate + * MSCAN related MCLK is the input to the MSCAN component + * + * in the absence of a clock-source spec, first an optimal clock + * gets determined based on the 'sys' clock, if that fails the + * 'ref' clock is used + */ + clk_from = CLK_FROM_AUTO; + if (clock_source) { + /* interpret the device tree's spec for the clock source */ + if (!strcmp(clock_source, "ip")) + clk_from = CLK_FROM_IPS; + else if (!strcmp(clock_source, "sys")) + clk_from = CLK_FROM_SYS; + else if (!strcmp(clock_source, "ref")) + clk_from = CLK_FROM_REF; + else + goto err_invalid; + dev_dbg(&ofdev->dev, "got a clk source spec[%d]\n", clk_from); + } + if (clk_from == CLK_FROM_AUTO) { + /* no spec so far, try the 'sys' clock; round to the + * next MHz and see if we can get a multiple of 16MHz + */ + dev_dbg(&ofdev->dev, "no clk source spec, trying SYS\n"); + clk_in = devm_clk_get(&ofdev->dev, "sys"); + if (IS_ERR(clk_in)) + goto err_notavail; + freq_calc = clk_get_rate(clk_in); + freq_calc += 499999; + freq_calc /= 1000000; + freq_calc *= 1000000; + if ((freq_calc % 16000000) == 0) { + clk_from = CLK_FROM_SYS; + clockdiv = freq_calc / 16000000; + dev_dbg(&ofdev->dev, + "clk fit, sys[%lu] div[%d] freq[%lu]\n", + freq_calc, clockdiv, freq_calc / clockdiv); + } + } + if (clk_from == CLK_FROM_AUTO) { + /* no spec so far, use the 'ref' clock */ + dev_dbg(&ofdev->dev, "no clk source spec, trying REF\n"); + clk_in = devm_clk_get(&ofdev->dev, "ref"); + if (IS_ERR(clk_in)) + goto err_notavail; + clk_from = CLK_FROM_REF; + freq_calc = clk_get_rate(clk_in); + dev_dbg(&ofdev->dev, + "clk fit, ref[%lu] (no div) freq[%lu]\n", + freq_calc, freq_calc); + } - /* - * Clock source and divider selection: 3 different clock sources - * can be selected: "ip", "ref" or "sys". For the latter two, a - * clock divider can be defined as well. If the clock source is - * not specified by the device tree, we first try to find an - * optimal CAN source clock based on the system clock. If that - * is not posslible, the reference clock will be used. + /* select IPS or MCLK as the MSCAN input (returned to the caller), + * setup the MCLK mux source and rate if applicable, apply the + * optionally specified or derived above divider, and determine + * the actual resulting clock rate to return to the caller */ - if (clock_name && !strcmp(clock_name, "ip")) { + switch (clk_from) { + case CLK_FROM_IPS: + clk_can = devm_clk_get(&ofdev->dev, "ips"); + if (IS_ERR(clk_can)) + goto err_notavail; + priv = netdev_priv(dev_get_drvdata(&ofdev->dev)); + priv->clk_can = clk_can; + freq_calc = clk_get_rate(clk_can); *mscan_clksrc = MSCAN_CLKSRC_IPS; - freq = mpc5xxx_get_bus_frequency(ofdev->dev.of_node); - } else { + dev_dbg(&ofdev->dev, "clk from IPS, clksrc[%d] freq[%lu]\n", + *mscan_clksrc, freq_calc); + break; + case CLK_FROM_SYS: + case CLK_FROM_REF: + clk_can = devm_clk_get(&ofdev->dev, "mclk"); + if (IS_ERR(clk_can)) + goto err_notavail; + priv = netdev_priv(dev_get_drvdata(&ofdev->dev)); + priv->clk_can = clk_can; + if (clk_from == CLK_FROM_SYS) + clk_in = devm_clk_get(&ofdev->dev, "sys"); + if (clk_from == CLK_FROM_REF) + clk_in = devm_clk_get(&ofdev->dev, "ref"); + if (IS_ERR(clk_in)) + goto err_notavail; + clk_set_parent(clk_can, clk_in); + freq_calc = clk_get_rate(clk_in); + freq_calc /= clockdiv; + clk_set_rate(clk_can, freq_calc); + freq_calc = clk_get_rate(clk_can); *mscan_clksrc = MSCAN_CLKSRC_BUS; - - pval = of_get_property(ofdev->dev.of_node, - "fsl,mscan-clock-divider", &plen); - if (pval && plen == sizeof(*pval)) - clockdiv = *pval; - if (!clockdiv) - clockdiv = 1; - - if (!clock_name || !strcmp(clock_name, "sys")) { - sys_clk = devm_clk_get(&ofdev->dev, "sys_clk"); - if (IS_ERR(sys_clk)) { - dev_err(&ofdev->dev, "couldn't get sys_clk\n"); - goto exit_unmap; - } - /* Get and round up/down sys clock rate */ - sys_freq = 1000000 * - ((clk_get_rate(sys_clk) + 499999) / 1000000); - - if (!clock_name) { - /* A multiple of 16 MHz would be optimal */ - if ((sys_freq % 16000000) == 0) { - clocksrc = 0; - clockdiv = sys_freq / 16000000; - freq = sys_freq / clockdiv; - } - } else { - clocksrc = 0; - freq = sys_freq / clockdiv; - } - } - - if (clocksrc < 0) { - ref_clk = devm_clk_get(&ofdev->dev, "ref_clk"); - if (IS_ERR(ref_clk)) { - dev_err(&ofdev->dev, "couldn't get ref_clk\n"); - goto exit_unmap; - } - clocksrc = 1; - freq = clk_get_rate(ref_clk) / clockdiv; - } + dev_dbg(&ofdev->dev, "clk from MCLK, clksrc[%d] freq[%lu]\n", + *mscan_clksrc, freq_calc); + break; + default: + goto err_invalid; } - /* Disable clock */ - out_be32(&clockctl->mccr[clockidx], 0x0); - if (clocksrc >= 0) { - /* Set source and divider */ - val = (clocksrc << 14) | ((clockdiv - 1) << 17); - out_be32(&clockctl->mccr[clockidx], val); - /* Enable clock */ - out_be32(&clockctl->mccr[clockidx], val | 0x10000); - } + /* the above clk_can item is used for the bitrate, access to + * the peripheral's register set needs the clk_ipg item + */ + clk_ipg = devm_clk_get(&ofdev->dev, "ipg"); + if (IS_ERR(clk_ipg)) + goto err_notavail_ipg; + if (clk_prepare_enable(clk_ipg)) + goto err_notavail_ipg; + priv = netdev_priv(dev_get_drvdata(&ofdev->dev)); + priv->clk_ipg = clk_ipg; + + /* return the determined clock source rate */ + return freq_calc; + +err_invalid: + dev_err(&ofdev->dev, "invalid clock source specification\n"); + /* clock source rate could not get determined */ + return 0; - /* Enable MSCAN clock domain */ - val = in_be32(&clockctl->sccr[1]); - if (!(val & (1 << 25))) - out_be32(&clockctl->sccr[1], val | (1 << 25)); +err_notavail: + dev_err(&ofdev->dev, "cannot acquire or setup bitrate clock source\n"); + /* clock source rate could not get determined */ + return 0; - dev_dbg(&ofdev->dev, "using '%s' with frequency divider %d\n", - *mscan_clksrc == MSCAN_CLKSRC_IPS ? "ips_clk" : - clocksrc == 1 ? "ref_clk" : "sys_clk", clockdiv); +err_notavail_ipg: + dev_err(&ofdev->dev, "cannot acquire or setup register clock\n"); + /* clock source rate could not get determined */ + return 0; +} -exit_unmap: - iounmap(clockctl); -exit_put: - of_node_put(np_clock); - return freq; +static void mpc512x_can_put_clock(struct platform_device *ofdev) +{ + struct mscan_priv *priv; + + priv = netdev_priv(dev_get_drvdata(&ofdev->dev)); + if (priv->clk_ipg) + clk_disable_unprepare(priv->clk_ipg); } #else /* !CONFIG_PPC_MPC512x */ static u32 mpc512x_can_get_clock(struct platform_device *ofdev, @@ -245,6 +279,7 @@ static u32 mpc512x_can_get_clock(struct platform_device *ofdev, { return 0; } +#define mpc512x_can_put_clock NULL #endif /* CONFIG_PPC_MPC512x */ static const struct of_device_id mpc5xxx_can_table[]; @@ -386,11 +421,13 @@ static int mpc5xxx_can_resume(struct platform_device *ofdev) static const struct mpc5xxx_can_data mpc5200_can_data = { .type = MSCAN_TYPE_MPC5200, .get_clock = mpc52xx_can_get_clock, + /* .put_clock not applicable */ }; static const struct mpc5xxx_can_data mpc5121_can_data = { .type = MSCAN_TYPE_MPC5121, .get_clock = mpc512x_can_get_clock, + .put_clock = mpc512x_can_put_clock, }; static const struct of_device_id mpc5xxx_can_table[] = { diff --git a/drivers/net/can/mscan/mscan.c b/drivers/net/can/mscan/mscan.c index a955ec8c4b9..e0c9be5e2ab 100644 --- a/drivers/net/can/mscan/mscan.c +++ b/drivers/net/can/mscan/mscan.c @@ -16,8 +16,7 @@ * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * along with this program; if not, see <http://www.gnu.org/licenses/>. */ #include <linux/kernel.h> @@ -648,9 +647,10 @@ static int mscan_close(struct net_device *dev) } static const struct net_device_ops mscan_netdev_ops = { - .ndo_open = mscan_open, - .ndo_stop = mscan_close, - .ndo_start_xmit = mscan_start_xmit, + .ndo_open = mscan_open, + .ndo_stop = mscan_close, + .ndo_start_xmit = mscan_start_xmit, + .ndo_change_mtu = can_change_mtu, }; int register_mscandev(struct net_device *dev, int mscan_clksrc) diff --git a/drivers/net/can/mscan/mscan.h b/drivers/net/can/mscan/mscan.h index 9c24d60a23b..ad8e08f9c49 100644 --- a/drivers/net/can/mscan/mscan.h +++ b/drivers/net/can/mscan/mscan.h @@ -14,8 +14,7 @@ * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * along with this program; if not, see <http://www.gnu.org/licenses/>. */ #ifndef __MSCAN_H__ @@ -297,8 +296,8 @@ struct mscan_priv { struct napi_struct napi; }; -extern struct net_device *alloc_mscandev(void); -extern int register_mscandev(struct net_device *dev, int mscan_clksrc); -extern void unregister_mscandev(struct net_device *dev); +struct net_device *alloc_mscandev(void); +int register_mscandev(struct net_device *dev, int mscan_clksrc); +void unregister_mscandev(struct net_device *dev); #endif /* __MSCAN_H__ */ diff --git a/drivers/net/can/pch_can.c b/drivers/net/can/pch_can.c index 5c314a96197..6472562efed 100644 --- a/drivers/net/can/pch_can.c +++ b/drivers/net/can/pch_can.c @@ -12,8 +12,7 @@ * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307, USA. + * along with this program; if not, see <http://www.gnu.org/licenses/>. */ #include <linux/interrupt.h> @@ -22,7 +21,6 @@ #include <linux/module.h> #include <linux/sched.h> #include <linux/pci.h> -#include <linux/init.h> #include <linux/kernel.h> #include <linux/types.h> #include <linux/errno.h> @@ -952,6 +950,7 @@ static const struct net_device_ops pch_can_netdev_ops = { .ndo_open = pch_can_open, .ndo_stop = pch_close, .ndo_start_xmit = pch_xmit, + .ndo_change_mtu = can_change_mtu, }; static void pch_can_remove(struct pci_dev *pdev) @@ -964,7 +963,6 @@ static void pch_can_remove(struct pci_dev *pdev) pci_disable_msi(priv->dev); pci_release_regions(pdev); pci_disable_device(pdev); - pci_set_drvdata(pdev, NULL); pch_can_reset(priv); pci_iounmap(pdev, priv->regs); free_candev(priv->ndev); diff --git a/drivers/net/can/rcar_can.c b/drivers/net/can/rcar_can.c new file mode 100644 index 00000000000..5268d216ecf --- /dev/null +++ b/drivers/net/can/rcar_can.c @@ -0,0 +1,876 @@ +/* Renesas R-Car CAN device driver + * + * Copyright (C) 2013 Cogent Embedded, Inc. <source@cogentembedded.com> + * Copyright (C) 2013 Renesas Solutions Corp. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/types.h> +#include <linux/interrupt.h> +#include <linux/errno.h> +#include <linux/netdevice.h> +#include <linux/platform_device.h> +#include <linux/can/led.h> +#include <linux/can/dev.h> +#include <linux/clk.h> +#include <linux/can/platform/rcar_can.h> + +#define RCAR_CAN_DRV_NAME "rcar_can" + +/* Mailbox configuration: + * mailbox 60 - 63 - Rx FIFO mailboxes + * mailbox 56 - 59 - Tx FIFO mailboxes + * non-FIFO mailboxes are not used + */ +#define RCAR_CAN_N_MBX 64 /* Number of mailboxes in non-FIFO mode */ +#define RCAR_CAN_RX_FIFO_MBX 60 /* Mailbox - window to Rx FIFO */ +#define RCAR_CAN_TX_FIFO_MBX 56 /* Mailbox - window to Tx FIFO */ +#define RCAR_CAN_FIFO_DEPTH 4 + +/* Mailbox registers structure */ +struct rcar_can_mbox_regs { + u32 id; /* IDE and RTR bits, SID and EID */ + u8 stub; /* Not used */ + u8 dlc; /* Data Length Code - bits [0..3] */ + u8 data[8]; /* Data Bytes */ + u8 tsh; /* Time Stamp Higher Byte */ + u8 tsl; /* Time Stamp Lower Byte */ +}; + +struct rcar_can_regs { + struct rcar_can_mbox_regs mb[RCAR_CAN_N_MBX]; /* Mailbox registers */ + u32 mkr_2_9[8]; /* Mask Registers 2-9 */ + u32 fidcr[2]; /* FIFO Received ID Compare Register */ + u32 mkivlr1; /* Mask Invalid Register 1 */ + u32 mier1; /* Mailbox Interrupt Enable Register 1 */ + u32 mkr_0_1[2]; /* Mask Registers 0-1 */ + u32 mkivlr0; /* Mask Invalid Register 0*/ + u32 mier0; /* Mailbox Interrupt Enable Register 0 */ + u8 pad_440[0x3c0]; + u8 mctl[64]; /* Message Control Registers */ + u16 ctlr; /* Control Register */ + u16 str; /* Status register */ + u8 bcr[3]; /* Bit Configuration Register */ + u8 clkr; /* Clock Select Register */ + u8 rfcr; /* Receive FIFO Control Register */ + u8 rfpcr; /* Receive FIFO Pointer Control Register */ + u8 tfcr; /* Transmit FIFO Control Register */ + u8 tfpcr; /* Transmit FIFO Pointer Control Register */ + u8 eier; /* Error Interrupt Enable Register */ + u8 eifr; /* Error Interrupt Factor Judge Register */ + u8 recr; /* Receive Error Count Register */ + u8 tecr; /* Transmit Error Count Register */ + u8 ecsr; /* Error Code Store Register */ + u8 cssr; /* Channel Search Support Register */ + u8 mssr; /* Mailbox Search Status Register */ + u8 msmr; /* Mailbox Search Mode Register */ + u16 tsr; /* Time Stamp Register */ + u8 afsr; /* Acceptance Filter Support Register */ + u8 pad_857; + u8 tcr; /* Test Control Register */ + u8 pad_859[7]; + u8 ier; /* Interrupt Enable Register */ + u8 isr; /* Interrupt Status Register */ + u8 pad_862; + u8 mbsmr; /* Mailbox Search Mask Register */ +}; + +struct rcar_can_priv { + struct can_priv can; /* Must be the first member! */ + struct net_device *ndev; + struct napi_struct napi; + struct rcar_can_regs __iomem *regs; + struct clk *clk; + u8 tx_dlc[RCAR_CAN_FIFO_DEPTH]; + u32 tx_head; + u32 tx_tail; + u8 clock_select; + u8 ier; +}; + +static const struct can_bittiming_const rcar_can_bittiming_const = { + .name = RCAR_CAN_DRV_NAME, + .tseg1_min = 4, + .tseg1_max = 16, + .tseg2_min = 2, + .tseg2_max = 8, + .sjw_max = 4, + .brp_min = 1, + .brp_max = 1024, + .brp_inc = 1, +}; + +/* Control Register bits */ +#define RCAR_CAN_CTLR_BOM (3 << 11) /* Bus-Off Recovery Mode Bits */ +#define RCAR_CAN_CTLR_BOM_ENT (1 << 11) /* Entry to halt mode */ + /* at bus-off entry */ +#define RCAR_CAN_CTLR_SLPM (1 << 10) +#define RCAR_CAN_CTLR_CANM (3 << 8) /* Operating Mode Select Bit */ +#define RCAR_CAN_CTLR_CANM_HALT (1 << 9) +#define RCAR_CAN_CTLR_CANM_RESET (1 << 8) +#define RCAR_CAN_CTLR_CANM_FORCE_RESET (3 << 8) +#define RCAR_CAN_CTLR_MLM (1 << 3) /* Message Lost Mode Select */ +#define RCAR_CAN_CTLR_IDFM (3 << 1) /* ID Format Mode Select Bits */ +#define RCAR_CAN_CTLR_IDFM_MIXED (1 << 2) /* Mixed ID mode */ +#define RCAR_CAN_CTLR_MBM (1 << 0) /* Mailbox Mode select */ + +/* Status Register bits */ +#define RCAR_CAN_STR_RSTST (1 << 8) /* Reset Status Bit */ + +/* FIFO Received ID Compare Registers 0 and 1 bits */ +#define RCAR_CAN_FIDCR_IDE (1 << 31) /* ID Extension Bit */ +#define RCAR_CAN_FIDCR_RTR (1 << 30) /* Remote Transmission Request Bit */ + +/* Receive FIFO Control Register bits */ +#define RCAR_CAN_RFCR_RFEST (1 << 7) /* Receive FIFO Empty Status Flag */ +#define RCAR_CAN_RFCR_RFE (1 << 0) /* Receive FIFO Enable */ + +/* Transmit FIFO Control Register bits */ +#define RCAR_CAN_TFCR_TFUST (7 << 1) /* Transmit FIFO Unsent Message */ + /* Number Status Bits */ +#define RCAR_CAN_TFCR_TFUST_SHIFT 1 /* Offset of Transmit FIFO Unsent */ + /* Message Number Status Bits */ +#define RCAR_CAN_TFCR_TFE (1 << 0) /* Transmit FIFO Enable */ + +#define RCAR_CAN_N_RX_MKREGS1 2 /* Number of mask registers */ + /* for Rx mailboxes 0-31 */ +#define RCAR_CAN_N_RX_MKREGS2 8 + +/* Bit Configuration Register settings */ +#define RCAR_CAN_BCR_TSEG1(x) (((x) & 0x0f) << 20) +#define RCAR_CAN_BCR_BPR(x) (((x) & 0x3ff) << 8) +#define RCAR_CAN_BCR_SJW(x) (((x) & 0x3) << 4) +#define RCAR_CAN_BCR_TSEG2(x) ((x) & 0x07) + +/* Mailbox and Mask Registers bits */ +#define RCAR_CAN_IDE (1 << 31) +#define RCAR_CAN_RTR (1 << 30) +#define RCAR_CAN_SID_SHIFT 18 + +/* Mailbox Interrupt Enable Register 1 bits */ +#define RCAR_CAN_MIER1_RXFIE (1 << 28) /* Receive FIFO Interrupt Enable */ +#define RCAR_CAN_MIER1_TXFIE (1 << 24) /* Transmit FIFO Interrupt Enable */ + +/* Interrupt Enable Register bits */ +#define RCAR_CAN_IER_ERSIE (1 << 5) /* Error (ERS) Interrupt Enable Bit */ +#define RCAR_CAN_IER_RXFIE (1 << 4) /* Reception FIFO Interrupt */ + /* Enable Bit */ +#define RCAR_CAN_IER_TXFIE (1 << 3) /* Transmission FIFO Interrupt */ + /* Enable Bit */ +/* Interrupt Status Register bits */ +#define RCAR_CAN_ISR_ERSF (1 << 5) /* Error (ERS) Interrupt Status Bit */ +#define RCAR_CAN_ISR_RXFF (1 << 4) /* Reception FIFO Interrupt */ + /* Status Bit */ +#define RCAR_CAN_ISR_TXFF (1 << 3) /* Transmission FIFO Interrupt */ + /* Status Bit */ + +/* Error Interrupt Enable Register bits */ +#define RCAR_CAN_EIER_BLIE (1 << 7) /* Bus Lock Interrupt Enable */ +#define RCAR_CAN_EIER_OLIE (1 << 6) /* Overload Frame Transmit */ + /* Interrupt Enable */ +#define RCAR_CAN_EIER_ORIE (1 << 5) /* Receive Overrun Interrupt Enable */ +#define RCAR_CAN_EIER_BORIE (1 << 4) /* Bus-Off Recovery Interrupt Enable */ +#define RCAR_CAN_EIER_BOEIE (1 << 3) /* Bus-Off Entry Interrupt Enable */ +#define RCAR_CAN_EIER_EPIE (1 << 2) /* Error Passive Interrupt Enable */ +#define RCAR_CAN_EIER_EWIE (1 << 1) /* Error Warning Interrupt Enable */ +#define RCAR_CAN_EIER_BEIE (1 << 0) /* Bus Error Interrupt Enable */ + +/* Error Interrupt Factor Judge Register bits */ +#define RCAR_CAN_EIFR_BLIF (1 << 7) /* Bus Lock Detect Flag */ +#define RCAR_CAN_EIFR_OLIF (1 << 6) /* Overload Frame Transmission */ + /* Detect Flag */ +#define RCAR_CAN_EIFR_ORIF (1 << 5) /* Receive Overrun Detect Flag */ +#define RCAR_CAN_EIFR_BORIF (1 << 4) /* Bus-Off Recovery Detect Flag */ +#define RCAR_CAN_EIFR_BOEIF (1 << 3) /* Bus-Off Entry Detect Flag */ +#define RCAR_CAN_EIFR_EPIF (1 << 2) /* Error Passive Detect Flag */ +#define RCAR_CAN_EIFR_EWIF (1 << 1) /* Error Warning Detect Flag */ +#define RCAR_CAN_EIFR_BEIF (1 << 0) /* Bus Error Detect Flag */ + +/* Error Code Store Register bits */ +#define RCAR_CAN_ECSR_EDPM (1 << 7) /* Error Display Mode Select Bit */ +#define RCAR_CAN_ECSR_ADEF (1 << 6) /* ACK Delimiter Error Flag */ +#define RCAR_CAN_ECSR_BE0F (1 << 5) /* Bit Error (dominant) Flag */ +#define RCAR_CAN_ECSR_BE1F (1 << 4) /* Bit Error (recessive) Flag */ +#define RCAR_CAN_ECSR_CEF (1 << 3) /* CRC Error Flag */ +#define RCAR_CAN_ECSR_AEF (1 << 2) /* ACK Error Flag */ +#define RCAR_CAN_ECSR_FEF (1 << 1) /* Form Error Flag */ +#define RCAR_CAN_ECSR_SEF (1 << 0) /* Stuff Error Flag */ + +#define RCAR_CAN_NAPI_WEIGHT 4 +#define MAX_STR_READS 0x100 + +static void tx_failure_cleanup(struct net_device *ndev) +{ + int i; + + for (i = 0; i < RCAR_CAN_FIFO_DEPTH; i++) + can_free_echo_skb(ndev, i); +} + +static void rcar_can_error(struct net_device *ndev) +{ + struct rcar_can_priv *priv = netdev_priv(ndev); + struct net_device_stats *stats = &ndev->stats; + struct can_frame *cf; + struct sk_buff *skb; + u8 eifr, txerr = 0, rxerr = 0; + + /* Propagate the error condition to the CAN stack */ + skb = alloc_can_err_skb(ndev, &cf); + + eifr = readb(&priv->regs->eifr); + if (eifr & (RCAR_CAN_EIFR_EWIF | RCAR_CAN_EIFR_EPIF)) { + txerr = readb(&priv->regs->tecr); + rxerr = readb(&priv->regs->recr); + if (skb) { + cf->can_id |= CAN_ERR_CRTL; + cf->data[6] = txerr; + cf->data[7] = rxerr; + } + } + if (eifr & RCAR_CAN_EIFR_BEIF) { + int rx_errors = 0, tx_errors = 0; + u8 ecsr; + + netdev_dbg(priv->ndev, "Bus error interrupt:\n"); + if (skb) { + cf->can_id |= CAN_ERR_BUSERROR | CAN_ERR_PROT; + cf->data[2] = CAN_ERR_PROT_UNSPEC; + } + ecsr = readb(&priv->regs->ecsr); + if (ecsr & RCAR_CAN_ECSR_ADEF) { + netdev_dbg(priv->ndev, "ACK Delimiter Error\n"); + tx_errors++; + writeb(~RCAR_CAN_ECSR_ADEF, &priv->regs->ecsr); + if (skb) + cf->data[3] |= CAN_ERR_PROT_LOC_ACK_DEL; + } + if (ecsr & RCAR_CAN_ECSR_BE0F) { + netdev_dbg(priv->ndev, "Bit Error (dominant)\n"); + tx_errors++; + writeb(~RCAR_CAN_ECSR_BE0F, &priv->regs->ecsr); + if (skb) + cf->data[2] |= CAN_ERR_PROT_BIT0; + } + if (ecsr & RCAR_CAN_ECSR_BE1F) { + netdev_dbg(priv->ndev, "Bit Error (recessive)\n"); + tx_errors++; + writeb(~RCAR_CAN_ECSR_BE1F, &priv->regs->ecsr); + if (skb) + cf->data[2] |= CAN_ERR_PROT_BIT1; + } + if (ecsr & RCAR_CAN_ECSR_CEF) { + netdev_dbg(priv->ndev, "CRC Error\n"); + rx_errors++; + writeb(~RCAR_CAN_ECSR_CEF, &priv->regs->ecsr); + if (skb) + cf->data[3] |= CAN_ERR_PROT_LOC_CRC_SEQ; + } + if (ecsr & RCAR_CAN_ECSR_AEF) { + netdev_dbg(priv->ndev, "ACK Error\n"); + tx_errors++; + writeb(~RCAR_CAN_ECSR_AEF, &priv->regs->ecsr); + if (skb) { + cf->can_id |= CAN_ERR_ACK; + cf->data[3] |= CAN_ERR_PROT_LOC_ACK; + } + } + if (ecsr & RCAR_CAN_ECSR_FEF) { + netdev_dbg(priv->ndev, "Form Error\n"); + rx_errors++; + writeb(~RCAR_CAN_ECSR_FEF, &priv->regs->ecsr); + if (skb) + cf->data[2] |= CAN_ERR_PROT_FORM; + } + if (ecsr & RCAR_CAN_ECSR_SEF) { + netdev_dbg(priv->ndev, "Stuff Error\n"); + rx_errors++; + writeb(~RCAR_CAN_ECSR_SEF, &priv->regs->ecsr); + if (skb) + cf->data[2] |= CAN_ERR_PROT_STUFF; + } + + priv->can.can_stats.bus_error++; + ndev->stats.rx_errors += rx_errors; + ndev->stats.tx_errors += tx_errors; + writeb(~RCAR_CAN_EIFR_BEIF, &priv->regs->eifr); + } + if (eifr & RCAR_CAN_EIFR_EWIF) { + netdev_dbg(priv->ndev, "Error warning interrupt\n"); + priv->can.state = CAN_STATE_ERROR_WARNING; + priv->can.can_stats.error_warning++; + /* Clear interrupt condition */ + writeb(~RCAR_CAN_EIFR_EWIF, &priv->regs->eifr); + if (skb) + cf->data[1] = txerr > rxerr ? CAN_ERR_CRTL_TX_WARNING : + CAN_ERR_CRTL_RX_WARNING; + } + if (eifr & RCAR_CAN_EIFR_EPIF) { + netdev_dbg(priv->ndev, "Error passive interrupt\n"); + priv->can.state = CAN_STATE_ERROR_PASSIVE; + priv->can.can_stats.error_passive++; + /* Clear interrupt condition */ + writeb(~RCAR_CAN_EIFR_EPIF, &priv->regs->eifr); + if (skb) + cf->data[1] = txerr > rxerr ? CAN_ERR_CRTL_TX_PASSIVE : + CAN_ERR_CRTL_RX_PASSIVE; + } + if (eifr & RCAR_CAN_EIFR_BOEIF) { + netdev_dbg(priv->ndev, "Bus-off entry interrupt\n"); + tx_failure_cleanup(ndev); + priv->ier = RCAR_CAN_IER_ERSIE; + writeb(priv->ier, &priv->regs->ier); + priv->can.state = CAN_STATE_BUS_OFF; + /* Clear interrupt condition */ + writeb(~RCAR_CAN_EIFR_BOEIF, &priv->regs->eifr); + can_bus_off(ndev); + if (skb) + cf->can_id |= CAN_ERR_BUSOFF; + } + if (eifr & RCAR_CAN_EIFR_ORIF) { + netdev_dbg(priv->ndev, "Receive overrun error interrupt\n"); + ndev->stats.rx_over_errors++; + ndev->stats.rx_errors++; + writeb(~RCAR_CAN_EIFR_ORIF, &priv->regs->eifr); + if (skb) { + cf->can_id |= CAN_ERR_CRTL; + cf->data[1] = CAN_ERR_CRTL_RX_OVERFLOW; + } + } + if (eifr & RCAR_CAN_EIFR_OLIF) { + netdev_dbg(priv->ndev, + "Overload Frame Transmission error interrupt\n"); + ndev->stats.rx_over_errors++; + ndev->stats.rx_errors++; + writeb(~RCAR_CAN_EIFR_OLIF, &priv->regs->eifr); + if (skb) { + cf->can_id |= CAN_ERR_PROT; + cf->data[2] |= CAN_ERR_PROT_OVERLOAD; + } + } + + if (skb) { + stats->rx_packets++; + stats->rx_bytes += cf->can_dlc; + netif_rx(skb); + } +} + +static void rcar_can_tx_done(struct net_device *ndev) +{ + struct rcar_can_priv *priv = netdev_priv(ndev); + struct net_device_stats *stats = &ndev->stats; + u8 isr; + + while (1) { + u8 unsent = readb(&priv->regs->tfcr); + + unsent = (unsent & RCAR_CAN_TFCR_TFUST) >> + RCAR_CAN_TFCR_TFUST_SHIFT; + if (priv->tx_head - priv->tx_tail <= unsent) + break; + stats->tx_packets++; + stats->tx_bytes += priv->tx_dlc[priv->tx_tail % + RCAR_CAN_FIFO_DEPTH]; + priv->tx_dlc[priv->tx_tail % RCAR_CAN_FIFO_DEPTH] = 0; + can_get_echo_skb(ndev, priv->tx_tail % RCAR_CAN_FIFO_DEPTH); + priv->tx_tail++; + netif_wake_queue(ndev); + } + /* Clear interrupt */ + isr = readb(&priv->regs->isr); + writeb(isr & ~RCAR_CAN_ISR_TXFF, &priv->regs->isr); + can_led_event(ndev, CAN_LED_EVENT_TX); +} + +static irqreturn_t rcar_can_interrupt(int irq, void *dev_id) +{ + struct net_device *ndev = dev_id; + struct rcar_can_priv *priv = netdev_priv(ndev); + u8 isr; + + isr = readb(&priv->regs->isr); + if (!(isr & priv->ier)) + return IRQ_NONE; + + if (isr & RCAR_CAN_ISR_ERSF) + rcar_can_error(ndev); + + if (isr & RCAR_CAN_ISR_TXFF) + rcar_can_tx_done(ndev); + + if (isr & RCAR_CAN_ISR_RXFF) { + if (napi_schedule_prep(&priv->napi)) { + /* Disable Rx FIFO interrupts */ + priv->ier &= ~RCAR_CAN_IER_RXFIE; + writeb(priv->ier, &priv->regs->ier); + __napi_schedule(&priv->napi); + } + } + + return IRQ_HANDLED; +} + +static void rcar_can_set_bittiming(struct net_device *dev) +{ + struct rcar_can_priv *priv = netdev_priv(dev); + struct can_bittiming *bt = &priv->can.bittiming; + u32 bcr; + + bcr = RCAR_CAN_BCR_TSEG1(bt->phase_seg1 + bt->prop_seg - 1) | + RCAR_CAN_BCR_BPR(bt->brp - 1) | RCAR_CAN_BCR_SJW(bt->sjw - 1) | + RCAR_CAN_BCR_TSEG2(bt->phase_seg2 - 1); + /* Don't overwrite CLKR with 32-bit BCR access; CLKR has 8-bit access. + * All the registers are big-endian but they get byte-swapped on 32-bit + * read/write (but not on 8-bit, contrary to the manuals)... + */ + writel((bcr << 8) | priv->clock_select, &priv->regs->bcr); +} + +static void rcar_can_start(struct net_device *ndev) +{ + struct rcar_can_priv *priv = netdev_priv(ndev); + u16 ctlr; + int i; + + /* Set controller to known mode: + * - FIFO mailbox mode + * - accept all messages + * - overrun mode + * CAN is in sleep mode after MCU hardware or software reset. + */ + ctlr = readw(&priv->regs->ctlr); + ctlr &= ~RCAR_CAN_CTLR_SLPM; + writew(ctlr, &priv->regs->ctlr); + /* Go to reset mode */ + ctlr |= RCAR_CAN_CTLR_CANM_FORCE_RESET; + writew(ctlr, &priv->regs->ctlr); + for (i = 0; i < MAX_STR_READS; i++) { + if (readw(&priv->regs->str) & RCAR_CAN_STR_RSTST) + break; + } + rcar_can_set_bittiming(ndev); + ctlr |= RCAR_CAN_CTLR_IDFM_MIXED; /* Select mixed ID mode */ + ctlr |= RCAR_CAN_CTLR_BOM_ENT; /* Entry to halt mode automatically */ + /* at bus-off */ + ctlr |= RCAR_CAN_CTLR_MBM; /* Select FIFO mailbox mode */ + ctlr |= RCAR_CAN_CTLR_MLM; /* Overrun mode */ + writew(ctlr, &priv->regs->ctlr); + + /* Accept all SID and EID */ + writel(0, &priv->regs->mkr_2_9[6]); + writel(0, &priv->regs->mkr_2_9[7]); + /* In FIFO mailbox mode, write "0" to bits 24 to 31 */ + writel(0, &priv->regs->mkivlr1); + /* Accept all frames */ + writel(0, &priv->regs->fidcr[0]); + writel(RCAR_CAN_FIDCR_IDE | RCAR_CAN_FIDCR_RTR, &priv->regs->fidcr[1]); + /* Enable and configure FIFO mailbox interrupts */ + writel(RCAR_CAN_MIER1_RXFIE | RCAR_CAN_MIER1_TXFIE, &priv->regs->mier1); + + priv->ier = RCAR_CAN_IER_ERSIE | RCAR_CAN_IER_RXFIE | + RCAR_CAN_IER_TXFIE; + writeb(priv->ier, &priv->regs->ier); + + /* Accumulate error codes */ + writeb(RCAR_CAN_ECSR_EDPM, &priv->regs->ecsr); + /* Enable error interrupts */ + writeb(RCAR_CAN_EIER_EWIE | RCAR_CAN_EIER_EPIE | RCAR_CAN_EIER_BOEIE | + (priv->can.ctrlmode & CAN_CTRLMODE_BERR_REPORTING ? + RCAR_CAN_EIER_BEIE : 0) | RCAR_CAN_EIER_ORIE | + RCAR_CAN_EIER_OLIE, &priv->regs->eier); + priv->can.state = CAN_STATE_ERROR_ACTIVE; + + /* Go to operation mode */ + writew(ctlr & ~RCAR_CAN_CTLR_CANM, &priv->regs->ctlr); + for (i = 0; i < MAX_STR_READS; i++) { + if (!(readw(&priv->regs->str) & RCAR_CAN_STR_RSTST)) + break; + } + /* Enable Rx and Tx FIFO */ + writeb(RCAR_CAN_RFCR_RFE, &priv->regs->rfcr); + writeb(RCAR_CAN_TFCR_TFE, &priv->regs->tfcr); +} + +static int rcar_can_open(struct net_device *ndev) +{ + struct rcar_can_priv *priv = netdev_priv(ndev); + int err; + + err = clk_prepare_enable(priv->clk); + if (err) { + netdev_err(ndev, "clk_prepare_enable() failed, error %d\n", + err); + goto out; + } + err = open_candev(ndev); + if (err) { + netdev_err(ndev, "open_candev() failed, error %d\n", err); + goto out_clock; + } + napi_enable(&priv->napi); + err = request_irq(ndev->irq, rcar_can_interrupt, 0, ndev->name, ndev); + if (err) { + netdev_err(ndev, "error requesting interrupt %x\n", ndev->irq); + goto out_close; + } + can_led_event(ndev, CAN_LED_EVENT_OPEN); + rcar_can_start(ndev); + netif_start_queue(ndev); + return 0; +out_close: + napi_disable(&priv->napi); + close_candev(ndev); +out_clock: + clk_disable_unprepare(priv->clk); +out: + return err; +} + +static void rcar_can_stop(struct net_device *ndev) +{ + struct rcar_can_priv *priv = netdev_priv(ndev); + u16 ctlr; + int i; + + /* Go to (force) reset mode */ + ctlr = readw(&priv->regs->ctlr); + ctlr |= RCAR_CAN_CTLR_CANM_FORCE_RESET; + writew(ctlr, &priv->regs->ctlr); + for (i = 0; i < MAX_STR_READS; i++) { + if (readw(&priv->regs->str) & RCAR_CAN_STR_RSTST) + break; + } + writel(0, &priv->regs->mier0); + writel(0, &priv->regs->mier1); + writeb(0, &priv->regs->ier); + writeb(0, &priv->regs->eier); + /* Go to sleep mode */ + ctlr |= RCAR_CAN_CTLR_SLPM; + writew(ctlr, &priv->regs->ctlr); + priv->can.state = CAN_STATE_STOPPED; +} + +static int rcar_can_close(struct net_device *ndev) +{ + struct rcar_can_priv *priv = netdev_priv(ndev); + + netif_stop_queue(ndev); + rcar_can_stop(ndev); + free_irq(ndev->irq, ndev); + napi_disable(&priv->napi); + clk_disable_unprepare(priv->clk); + close_candev(ndev); + can_led_event(ndev, CAN_LED_EVENT_STOP); + return 0; +} + +static netdev_tx_t rcar_can_start_xmit(struct sk_buff *skb, + struct net_device *ndev) +{ + struct rcar_can_priv *priv = netdev_priv(ndev); + struct can_frame *cf = (struct can_frame *)skb->data; + u32 data, i; + + if (can_dropped_invalid_skb(ndev, skb)) + return NETDEV_TX_OK; + + if (cf->can_id & CAN_EFF_FLAG) /* Extended frame format */ + data = (cf->can_id & CAN_EFF_MASK) | RCAR_CAN_IDE; + else /* Standard frame format */ + data = (cf->can_id & CAN_SFF_MASK) << RCAR_CAN_SID_SHIFT; + + if (cf->can_id & CAN_RTR_FLAG) { /* Remote transmission request */ + data |= RCAR_CAN_RTR; + } else { + for (i = 0; i < cf->can_dlc; i++) + writeb(cf->data[i], + &priv->regs->mb[RCAR_CAN_TX_FIFO_MBX].data[i]); + } + + writel(data, &priv->regs->mb[RCAR_CAN_TX_FIFO_MBX].id); + + writeb(cf->can_dlc, &priv->regs->mb[RCAR_CAN_TX_FIFO_MBX].dlc); + + priv->tx_dlc[priv->tx_head % RCAR_CAN_FIFO_DEPTH] = cf->can_dlc; + can_put_echo_skb(skb, ndev, priv->tx_head % RCAR_CAN_FIFO_DEPTH); + priv->tx_head++; + /* Start Tx: write 0xff to the TFPCR register to increment + * the CPU-side pointer for the transmit FIFO to the next + * mailbox location + */ + writeb(0xff, &priv->regs->tfpcr); + /* Stop the queue if we've filled all FIFO entries */ + if (priv->tx_head - priv->tx_tail >= RCAR_CAN_FIFO_DEPTH) + netif_stop_queue(ndev); + + return NETDEV_TX_OK; +} + +static const struct net_device_ops rcar_can_netdev_ops = { + .ndo_open = rcar_can_open, + .ndo_stop = rcar_can_close, + .ndo_start_xmit = rcar_can_start_xmit, +}; + +static void rcar_can_rx_pkt(struct rcar_can_priv *priv) +{ + struct net_device_stats *stats = &priv->ndev->stats; + struct can_frame *cf; + struct sk_buff *skb; + u32 data; + u8 dlc; + + skb = alloc_can_skb(priv->ndev, &cf); + if (!skb) { + stats->rx_dropped++; + return; + } + + data = readl(&priv->regs->mb[RCAR_CAN_RX_FIFO_MBX].id); + if (data & RCAR_CAN_IDE) + cf->can_id = (data & CAN_EFF_MASK) | CAN_EFF_FLAG; + else + cf->can_id = (data >> RCAR_CAN_SID_SHIFT) & CAN_SFF_MASK; + + dlc = readb(&priv->regs->mb[RCAR_CAN_RX_FIFO_MBX].dlc); + cf->can_dlc = get_can_dlc(dlc); + if (data & RCAR_CAN_RTR) { + cf->can_id |= CAN_RTR_FLAG; + } else { + for (dlc = 0; dlc < cf->can_dlc; dlc++) + cf->data[dlc] = + readb(&priv->regs->mb[RCAR_CAN_RX_FIFO_MBX].data[dlc]); + } + + can_led_event(priv->ndev, CAN_LED_EVENT_RX); + + stats->rx_bytes += cf->can_dlc; + stats->rx_packets++; + netif_receive_skb(skb); +} + +static int rcar_can_rx_poll(struct napi_struct *napi, int quota) +{ + struct rcar_can_priv *priv = container_of(napi, + struct rcar_can_priv, napi); + int num_pkts; + + for (num_pkts = 0; num_pkts < quota; num_pkts++) { + u8 rfcr, isr; + + isr = readb(&priv->regs->isr); + /* Clear interrupt bit */ + if (isr & RCAR_CAN_ISR_RXFF) + writeb(isr & ~RCAR_CAN_ISR_RXFF, &priv->regs->isr); + rfcr = readb(&priv->regs->rfcr); + if (rfcr & RCAR_CAN_RFCR_RFEST) + break; + rcar_can_rx_pkt(priv); + /* Write 0xff to the RFPCR register to increment + * the CPU-side pointer for the receive FIFO + * to the next mailbox location + */ + writeb(0xff, &priv->regs->rfpcr); + } + /* All packets processed */ + if (num_pkts < quota) { + napi_complete(napi); + priv->ier |= RCAR_CAN_IER_RXFIE; + writeb(priv->ier, &priv->regs->ier); + } + return num_pkts; +} + +static int rcar_can_do_set_mode(struct net_device *ndev, enum can_mode mode) +{ + switch (mode) { + case CAN_MODE_START: + rcar_can_start(ndev); + netif_wake_queue(ndev); + return 0; + default: + return -EOPNOTSUPP; + } +} + +static int rcar_can_get_berr_counter(const struct net_device *dev, + struct can_berr_counter *bec) +{ + struct rcar_can_priv *priv = netdev_priv(dev); + int err; + + err = clk_prepare_enable(priv->clk); + if (err) + return err; + bec->txerr = readb(&priv->regs->tecr); + bec->rxerr = readb(&priv->regs->recr); + clk_disable_unprepare(priv->clk); + return 0; +} + +static int rcar_can_probe(struct platform_device *pdev) +{ + struct rcar_can_platform_data *pdata; + struct rcar_can_priv *priv; + struct net_device *ndev; + struct resource *mem; + void __iomem *addr; + int err = -ENODEV; + int irq; + + pdata = dev_get_platdata(&pdev->dev); + if (!pdata) { + dev_err(&pdev->dev, "No platform data provided!\n"); + goto fail; + } + + irq = platform_get_irq(pdev, 0); + if (!irq) { + dev_err(&pdev->dev, "No IRQ resource\n"); + goto fail; + } + + mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); + addr = devm_ioremap_resource(&pdev->dev, mem); + if (IS_ERR(addr)) { + err = PTR_ERR(addr); + goto fail; + } + + ndev = alloc_candev(sizeof(struct rcar_can_priv), RCAR_CAN_FIFO_DEPTH); + if (!ndev) { + dev_err(&pdev->dev, "alloc_candev() failed\n"); + err = -ENOMEM; + goto fail; + } + + priv = netdev_priv(ndev); + + priv->clk = devm_clk_get(&pdev->dev, NULL); + if (IS_ERR(priv->clk)) { + err = PTR_ERR(priv->clk); + dev_err(&pdev->dev, "cannot get clock: %d\n", err); + goto fail_clk; + } + + ndev->netdev_ops = &rcar_can_netdev_ops; + ndev->irq = irq; + ndev->flags |= IFF_ECHO; + priv->ndev = ndev; + priv->regs = addr; + priv->clock_select = pdata->clock_select; + priv->can.clock.freq = clk_get_rate(priv->clk); + priv->can.bittiming_const = &rcar_can_bittiming_const; + priv->can.do_set_mode = rcar_can_do_set_mode; + priv->can.do_get_berr_counter = rcar_can_get_berr_counter; + priv->can.ctrlmode_supported = CAN_CTRLMODE_BERR_REPORTING; + platform_set_drvdata(pdev, ndev); + SET_NETDEV_DEV(ndev, &pdev->dev); + + netif_napi_add(ndev, &priv->napi, rcar_can_rx_poll, + RCAR_CAN_NAPI_WEIGHT); + err = register_candev(ndev); + if (err) { + dev_err(&pdev->dev, "register_candev() failed, error %d\n", + err); + goto fail_candev; + } + + devm_can_led_init(ndev); + + dev_info(&pdev->dev, "device registered (reg_base=%p, irq=%u)\n", + priv->regs, ndev->irq); + + return 0; +fail_candev: + netif_napi_del(&priv->napi); +fail_clk: + free_candev(ndev); +fail: + return err; +} + +static int rcar_can_remove(struct platform_device *pdev) +{ + struct net_device *ndev = platform_get_drvdata(pdev); + struct rcar_can_priv *priv = netdev_priv(ndev); + + unregister_candev(ndev); + netif_napi_del(&priv->napi); + free_candev(ndev); + return 0; +} + +static int __maybe_unused rcar_can_suspend(struct device *dev) +{ + struct net_device *ndev = dev_get_drvdata(dev); + struct rcar_can_priv *priv = netdev_priv(ndev); + u16 ctlr; + + if (netif_running(ndev)) { + netif_stop_queue(ndev); + netif_device_detach(ndev); + } + ctlr = readw(&priv->regs->ctlr); + ctlr |= RCAR_CAN_CTLR_CANM_HALT; + writew(ctlr, &priv->regs->ctlr); + ctlr |= RCAR_CAN_CTLR_SLPM; + writew(ctlr, &priv->regs->ctlr); + priv->can.state = CAN_STATE_SLEEPING; + + clk_disable(priv->clk); + return 0; +} + +static int __maybe_unused rcar_can_resume(struct device *dev) +{ + struct net_device *ndev = dev_get_drvdata(dev); + struct rcar_can_priv *priv = netdev_priv(ndev); + u16 ctlr; + int err; + + err = clk_enable(priv->clk); + if (err) { + netdev_err(ndev, "clk_enable() failed, error %d\n", err); + return err; + } + + ctlr = readw(&priv->regs->ctlr); + ctlr &= ~RCAR_CAN_CTLR_SLPM; + writew(ctlr, &priv->regs->ctlr); + ctlr &= ~RCAR_CAN_CTLR_CANM; + writew(ctlr, &priv->regs->ctlr); + priv->can.state = CAN_STATE_ERROR_ACTIVE; + + if (netif_running(ndev)) { + netif_device_attach(ndev); + netif_start_queue(ndev); + } + return 0; +} + +static SIMPLE_DEV_PM_OPS(rcar_can_pm_ops, rcar_can_suspend, rcar_can_resume); + +static struct platform_driver rcar_can_driver = { + .driver = { + .name = RCAR_CAN_DRV_NAME, + .owner = THIS_MODULE, + .pm = &rcar_can_pm_ops, + }, + .probe = rcar_can_probe, + .remove = rcar_can_remove, +}; + +module_platform_driver(rcar_can_driver); + +MODULE_AUTHOR("Cogent Embedded, Inc."); +MODULE_LICENSE("GPL"); +MODULE_DESCRIPTION("CAN driver for Renesas R-Car SoC"); +MODULE_ALIAS("platform:" RCAR_CAN_DRV_NAME); diff --git a/drivers/net/can/sja1000/Kconfig b/drivers/net/can/sja1000/Kconfig index ff2ba86cd4a..1e65cb6c259 100644 --- a/drivers/net/can/sja1000/Kconfig +++ b/drivers/net/can/sja1000/Kconfig @@ -17,16 +17,9 @@ config CAN_SJA1000_PLATFORM the "platform bus" (Linux abstraction for directly to the processor attached devices). Which can be found on various boards from Phytec (http://www.phytec.de) like the PCM027, - PCM038. - -config CAN_SJA1000_OF_PLATFORM - tristate "Generic OF Platform Bus based SJA1000 driver" - depends on OF - ---help--- - This driver adds support for the SJA1000 chips connected to - the OpenFirmware "platform bus" found on embedded systems with - OpenFirmware bindings, e.g. if you have a PowerPC based system - you may want to enable this option. + PCM038. It also provides the OpenFirmware "platform bus" found + on embedded systems with OpenFirmware bindings, e.g. if you + have a PowerPC based system you may want to enable this option. config CAN_EMS_PCMCIA tristate "EMS CPC-CARD Card" @@ -46,7 +39,7 @@ config CAN_EMS_PCI config CAN_PEAK_PCMCIA tristate "PEAK PCAN-PC Card" depends on PCMCIA - depends on HAS_IOPORT + depends on HAS_IOPORT_MAP ---help--- This driver is for the PCAN-PC Card PCMCIA adapter (1 or 2 channels) from PEAK-System (http://www.peak-system.com). To compile this diff --git a/drivers/net/can/sja1000/Makefile b/drivers/net/can/sja1000/Makefile index b3d05cbfec3..531d5fcc97e 100644 --- a/drivers/net/can/sja1000/Makefile +++ b/drivers/net/can/sja1000/Makefile @@ -5,7 +5,6 @@ obj-$(CONFIG_CAN_SJA1000) += sja1000.o obj-$(CONFIG_CAN_SJA1000_ISA) += sja1000_isa.o obj-$(CONFIG_CAN_SJA1000_PLATFORM) += sja1000_platform.o -obj-$(CONFIG_CAN_SJA1000_OF_PLATFORM) += sja1000_of_platform.o obj-$(CONFIG_CAN_EMS_PCMCIA) += ems_pcmcia.o obj-$(CONFIG_CAN_EMS_PCI) += ems_pci.o obj-$(CONFIG_CAN_KVASER_PCI) += kvaser_pci.o diff --git a/drivers/net/can/sja1000/ems_pci.c b/drivers/net/can/sja1000/ems_pci.c index 3752342a678..fd13dbf07d9 100644 --- a/drivers/net/can/sja1000/ems_pci.c +++ b/drivers/net/can/sja1000/ems_pci.c @@ -13,8 +13,7 @@ * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software Foundation, - * Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + * along with this program; if not, see <http://www.gnu.org/licenses/>. */ #include <linux/kernel.h> @@ -207,7 +206,6 @@ static void ems_pci_del_card(struct pci_dev *pdev) kfree(card); pci_disable_device(pdev); - pci_set_drvdata(pdev, NULL); } static void ems_pci_card_reset(struct ems_pci_card *card) @@ -325,6 +323,7 @@ static int ems_pci_add_card(struct pci_dev *pdev, priv->cdr = EMS_PCI_CDR; SET_NETDEV_DEV(dev, &pdev->dev); + dev->dev_id = i; if (card->version == 1) /* reset int flag of pita */ diff --git a/drivers/net/can/sja1000/ems_pcmcia.c b/drivers/net/can/sja1000/ems_pcmcia.c index 9e535f2ef52..381de998d2f 100644 --- a/drivers/net/can/sja1000/ems_pcmcia.c +++ b/drivers/net/can/sja1000/ems_pcmcia.c @@ -211,6 +211,7 @@ static int ems_pcmcia_add_card(struct pcmcia_device *pdev, unsigned long base) priv = netdev_priv(dev); priv->priv = card; SET_NETDEV_DEV(dev, &pdev->dev); + dev->dev_id = i; priv->irq_flags = IRQF_SHARED; dev->irq = pdev->irq; diff --git a/drivers/net/can/sja1000/kvaser_pci.c b/drivers/net/can/sja1000/kvaser_pci.c index 217585b97cd..23b8e1324e2 100644 --- a/drivers/net/can/sja1000/kvaser_pci.c +++ b/drivers/net/can/sja1000/kvaser_pci.c @@ -26,8 +26,7 @@ * General Public License for more details. * * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software Foundation, - * Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + * along with this program; if not, see <http://www.gnu.org/licenses/>. */ #include <linux/kernel.h> @@ -271,6 +270,7 @@ static int kvaser_pci_add_chan(struct pci_dev *pdev, int channel, priv->reg_base, board->conf_addr, dev->irq); SET_NETDEV_DEV(dev, &pdev->dev); + dev->dev_id = channel; /* Register SJA1000 device */ err = register_sja1000dev(dev); @@ -387,7 +387,6 @@ static void kvaser_pci_remove_one(struct pci_dev *pdev) pci_release_regions(pdev); pci_disable_device(pdev); - pci_set_drvdata(pdev, NULL); } static struct pci_driver kvaser_pci_driver = { diff --git a/drivers/net/can/sja1000/peak_pci.c b/drivers/net/can/sja1000/peak_pci.c index 6b6f0ad7509..564933ae218 100644 --- a/drivers/net/can/sja1000/peak_pci.c +++ b/drivers/net/can/sja1000/peak_pci.c @@ -551,7 +551,7 @@ static int peak_pci_probe(struct pci_dev *pdev, const struct pci_device_id *ent) { struct sja1000_priv *priv; struct peak_pci_chan *chan; - struct net_device *dev; + struct net_device *dev, *prev_dev; void __iomem *cfg_base, *reg_base; u16 sub_sys_id, icr; int i, err, channels; @@ -642,6 +642,7 @@ static int peak_pci_probe(struct pci_dev *pdev, const struct pci_device_id *ent) icr |= chan->icr_mask; SET_NETDEV_DEV(dev, &pdev->dev); + dev->dev_id = i; /* Create chain of SJA1000 devices */ chan->prev_dev = pci_get_drvdata(pdev); @@ -687,11 +688,13 @@ failure_remove_channels: writew(0x0, cfg_base + PITA_ICR + 2); chan = NULL; - for (dev = pci_get_drvdata(pdev); dev; dev = chan->prev_dev) { - unregister_sja1000dev(dev); - free_sja1000dev(dev); + for (dev = pci_get_drvdata(pdev); dev; dev = prev_dev) { priv = netdev_priv(dev); chan = priv->priv; + prev_dev = chan->prev_dev; + + unregister_sja1000dev(dev); + free_sja1000dev(dev); } /* free any PCIeC resources too */ @@ -725,10 +728,12 @@ static void peak_pci_remove(struct pci_dev *pdev) /* Loop over all registered devices */ while (1) { + struct net_device *prev_dev = chan->prev_dev; + dev_info(&pdev->dev, "removing device %s\n", dev->name); unregister_sja1000dev(dev); free_sja1000dev(dev); - dev = chan->prev_dev; + dev = prev_dev; if (!dev) { /* do that only for first channel */ @@ -744,8 +749,6 @@ static void peak_pci_remove(struct pci_dev *pdev) pci_iounmap(pdev, cfg_base); pci_release_regions(pdev); pci_disable_device(pdev); - - pci_set_drvdata(pdev, NULL); } static struct pci_driver peak_pci_driver = { diff --git a/drivers/net/can/sja1000/peak_pcmcia.c b/drivers/net/can/sja1000/peak_pcmcia.c index f7ad754dd2a..dd56133cc46 100644 --- a/drivers/net/can/sja1000/peak_pcmcia.c +++ b/drivers/net/can/sja1000/peak_pcmcia.c @@ -550,6 +550,7 @@ static int pcan_add_channels(struct pcan_pccard *card) priv = netdev_priv(netdev); priv->priv = card; SET_NETDEV_DEV(netdev, &pdev->dev); + netdev->dev_id = i; priv->irq_flags = IRQF_SHARED; netdev->irq = pdev->irq; diff --git a/drivers/net/can/sja1000/plx_pci.c b/drivers/net/can/sja1000/plx_pci.c index c52c1e96bf9..ec39b7cb228 100644 --- a/drivers/net/can/sja1000/plx_pci.c +++ b/drivers/net/can/sja1000/plx_pci.c @@ -16,8 +16,7 @@ * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software Foundation, - * Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + * along with this program; if not, see <http://www.gnu.org/licenses/>. */ #include <linux/kernel.h> @@ -45,7 +44,8 @@ MODULE_SUPPORTED_DEVICE("Adlink PCI-7841/cPCI-7841, " "esd CAN-PCI/PMC/266, " "esd CAN-PCIe/2000, " "Connect Tech Inc. CANpro/104-Plus Opto (CRG001), " - "IXXAT PC-I 04/PCI") + "IXXAT PC-I 04/PCI, " + "ELCUS CAN-200-PCI") MODULE_LICENSE("GPL v2"); #define PLX_PCI_MAX_CHAN 2 @@ -123,6 +123,11 @@ struct plx_pci_card { #define ESD_PCI_SUB_SYS_ID_PCIE2000 0x0200 #define ESD_PCI_SUB_SYS_ID_PCI104200 0x0501 +#define CAN200PCI_DEVICE_ID 0x9030 +#define CAN200PCI_VENDOR_ID 0x10b5 +#define CAN200PCI_SUB_DEVICE_ID 0x0301 +#define CAN200PCI_SUB_VENDOR_ID 0xe1c5 + #define IXXAT_PCI_VENDOR_ID 0x10b5 #define IXXAT_PCI_DEVICE_ID 0x9050 #define IXXAT_PCI_SUB_SYS_ID 0x2540 @@ -234,6 +239,14 @@ static struct plx_pci_card_info plx_pci_card_info_cti = { /* based on PLX9030 */ }; +static struct plx_pci_card_info plx_pci_card_info_elcus = { + "Eclus CAN-200-PCI", 2, + PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR, + {1, 0x00, 0x00}, { {2, 0x00, 0x80}, {3, 0x00, 0x80} }, + &plx_pci_reset_common + /* based on PLX9030 */ +}; + static DEFINE_PCI_DEVICE_TABLE(plx_pci_tbl) = { { /* Adlink PCI-7841/cPCI-7841 */ @@ -319,6 +332,13 @@ static DEFINE_PCI_DEVICE_TABLE(plx_pci_tbl) = { 0, 0, (kernel_ulong_t)&plx_pci_card_info_cti }, + { + /* Elcus CAN-200-PCI */ + CAN200PCI_VENDOR_ID, CAN200PCI_DEVICE_ID, + CAN200PCI_SUB_VENDOR_ID, CAN200PCI_SUB_DEVICE_ID, + 0, 0, + (kernel_ulong_t)&plx_pci_card_info_elcus + }, { 0,} }; MODULE_DEVICE_TABLE(pci, plx_pci_tbl); @@ -477,7 +497,6 @@ static void plx_pci_del_card(struct pci_dev *pdev) kfree(card); pci_disable_device(pdev); - pci_set_drvdata(pdev, NULL); } /* @@ -568,6 +587,7 @@ static int plx_pci_add_card(struct pci_dev *pdev, priv->cdr = ci->cdr; SET_NETDEV_DEV(dev, &pdev->dev); + dev->dev_id = i; /* Register SJA1000 device */ err = register_sja1000dev(dev); diff --git a/drivers/net/can/sja1000/sja1000.c b/drivers/net/can/sja1000/sja1000.c index 7164a999f50..f31499a32d7 100644 --- a/drivers/net/can/sja1000/sja1000.c +++ b/drivers/net/can/sja1000/sja1000.c @@ -106,8 +106,7 @@ static int sja1000_probe_chip(struct net_device *dev) struct sja1000_priv *priv = netdev_priv(dev); if (priv->reg_base && sja1000_is_absent(priv)) { - printk(KERN_INFO "%s: probing @0x%lX failed\n", - DRV_NAME, dev->base_addr); + netdev_err(dev, "probing failed\n"); return 0; } return -1; @@ -494,20 +493,20 @@ irqreturn_t sja1000_interrupt(int irq, void *dev_id) uint8_t isrc, status; int n = 0; - /* Shared interrupts and IRQ off? */ - if (priv->read_reg(priv, SJA1000_IER) == IRQ_OFF) - return IRQ_NONE; - if (priv->pre_irq) priv->pre_irq(priv); + /* Shared interrupts and IRQ off? */ + if (priv->read_reg(priv, SJA1000_IER) == IRQ_OFF) + goto out; + while ((isrc = priv->read_reg(priv, SJA1000_IR)) && (n < SJA1000_MAX_IRQ)) { - n++; + status = priv->read_reg(priv, SJA1000_SR); /* check for absent controller due to hw unplug */ if (status == 0xFF && sja1000_is_absent(priv)) - return IRQ_NONE; + goto out; if (isrc & IRQ_WUI) netdev_warn(dev, "wakeup interrupt\n"); @@ -535,7 +534,7 @@ irqreturn_t sja1000_interrupt(int irq, void *dev_id) status = priv->read_reg(priv, SJA1000_SR); /* check for absent controller */ if (status == 0xFF && sja1000_is_absent(priv)) - return IRQ_NONE; + goto out; } } if (isrc & (IRQ_DOI | IRQ_EI | IRQ_BEI | IRQ_EPI | IRQ_ALI)) { @@ -543,8 +542,9 @@ irqreturn_t sja1000_interrupt(int irq, void *dev_id) if (sja1000_err(dev, isrc, status)) break; } + n++; } - +out: if (priv->post_irq) priv->post_irq(priv); @@ -642,9 +642,10 @@ void free_sja1000dev(struct net_device *dev) EXPORT_SYMBOL_GPL(free_sja1000dev); static const struct net_device_ops sja1000_netdev_ops = { - .ndo_open = sja1000_open, - .ndo_stop = sja1000_close, - .ndo_start_xmit = sja1000_start_xmit, + .ndo_open = sja1000_open, + .ndo_stop = sja1000_close, + .ndo_start_xmit = sja1000_start_xmit, + .ndo_change_mtu = can_change_mtu, }; int register_sja1000dev(struct net_device *dev) diff --git a/drivers/net/can/sja1000/sja1000_isa.c b/drivers/net/can/sja1000/sja1000_isa.c index 06a282397ff..014695d7e6a 100644 --- a/drivers/net/can/sja1000/sja1000_isa.c +++ b/drivers/net/can/sja1000/sja1000_isa.c @@ -11,8 +11,7 @@ * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * along with this program; if not, see <http://www.gnu.org/licenses/>. */ #include <linux/kernel.h> @@ -47,6 +46,7 @@ static int clk[MAXDEV]; static unsigned char cdr[MAXDEV] = {[0 ... (MAXDEV - 1)] = 0xff}; static unsigned char ocr[MAXDEV] = {[0 ... (MAXDEV - 1)] = 0xff}; static int indirect[MAXDEV] = {[0 ... (MAXDEV - 1)] = -1}; +static spinlock_t indirect_lock[MAXDEV]; /* lock for indirect access mode */ module_param_array(port, ulong, NULL, S_IRUGO); MODULE_PARM_DESC(port, "I/O port number"); @@ -102,19 +102,26 @@ static void sja1000_isa_port_write_reg(const struct sja1000_priv *priv, static u8 sja1000_isa_port_read_reg_indirect(const struct sja1000_priv *priv, int reg) { - unsigned long base = (unsigned long)priv->reg_base; + unsigned long flags, base = (unsigned long)priv->reg_base; + u8 readval; + spin_lock_irqsave(&indirect_lock[priv->dev->dev_id], flags); outb(reg, base); - return inb(base + 1); + readval = inb(base + 1); + spin_unlock_irqrestore(&indirect_lock[priv->dev->dev_id], flags); + + return readval; } static void sja1000_isa_port_write_reg_indirect(const struct sja1000_priv *priv, int reg, u8 val) { - unsigned long base = (unsigned long)priv->reg_base; + unsigned long flags, base = (unsigned long)priv->reg_base; + spin_lock_irqsave(&indirect_lock[priv->dev->dev_id], flags); outb(reg, base); outb(val, base + 1); + spin_unlock_irqrestore(&indirect_lock[priv->dev->dev_id], flags); } static int sja1000_isa_probe(struct platform_device *pdev) @@ -170,6 +177,7 @@ static int sja1000_isa_probe(struct platform_device *pdev) if (iosize == SJA1000_IOSIZE_INDIRECT) { priv->read_reg = sja1000_isa_port_read_reg_indirect; priv->write_reg = sja1000_isa_port_write_reg_indirect; + spin_lock_init(&indirect_lock[idx]); } else { priv->read_reg = sja1000_isa_port_read_reg; priv->write_reg = sja1000_isa_port_write_reg; @@ -199,6 +207,7 @@ static int sja1000_isa_probe(struct platform_device *pdev) platform_set_drvdata(pdev, dev); SET_NETDEV_DEV(dev, &pdev->dev); + dev->dev_id = idx; err = register_sja1000dev(dev); if (err) { diff --git a/drivers/net/can/sja1000/sja1000_of_platform.c b/drivers/net/can/sja1000/sja1000_of_platform.c deleted file mode 100644 index 31ad3391116..00000000000 --- a/drivers/net/can/sja1000/sja1000_of_platform.c +++ /dev/null @@ -1,222 +0,0 @@ -/* - * Driver for SJA1000 CAN controllers on the OpenFirmware platform bus - * - * Copyright (C) 2008-2009 Wolfgang Grandegger <wg@grandegger.com> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the version 2 of the GNU General Public License - * as published by the Free Software Foundation - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software Foundation, - * Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. - */ - -/* This is a generic driver for SJA1000 chips on the OpenFirmware platform - * bus found on embedded PowerPC systems. You need a SJA1000 CAN node - * definition in your flattened device tree source (DTS) file similar to: - * - * can@3,100 { - * compatible = "nxp,sja1000"; - * reg = <3 0x100 0x80>; - * interrupts = <2 0>; - * interrupt-parent = <&mpic>; - * nxp,external-clock-frequency = <16000000>; - * }; - * - * See "Documentation/devicetree/bindings/net/can/sja1000.txt" for further - * information. - */ - -#include <linux/kernel.h> -#include <linux/module.h> -#include <linux/interrupt.h> -#include <linux/netdevice.h> -#include <linux/delay.h> -#include <linux/io.h> -#include <linux/can/dev.h> - -#include <linux/of_platform.h> -#include <linux/of_address.h> -#include <linux/of_irq.h> -#include <asm/prom.h> - -#include "sja1000.h" - -#define DRV_NAME "sja1000_of_platform" - -MODULE_AUTHOR("Wolfgang Grandegger <wg@grandegger.com>"); -MODULE_DESCRIPTION("Socket-CAN driver for SJA1000 on the OF platform bus"); -MODULE_LICENSE("GPL v2"); - -#define SJA1000_OFP_CAN_CLOCK (16000000 / 2) - -#define SJA1000_OFP_OCR OCR_TX0_PULLDOWN -#define SJA1000_OFP_CDR (CDR_CBP | CDR_CLK_OFF) - -static u8 sja1000_ofp_read_reg(const struct sja1000_priv *priv, int reg) -{ - return ioread8(priv->reg_base + reg); -} - -static void sja1000_ofp_write_reg(const struct sja1000_priv *priv, - int reg, u8 val) -{ - iowrite8(val, priv->reg_base + reg); -} - -static int sja1000_ofp_remove(struct platform_device *ofdev) -{ - struct net_device *dev = platform_get_drvdata(ofdev); - struct sja1000_priv *priv = netdev_priv(dev); - struct device_node *np = ofdev->dev.of_node; - struct resource res; - - unregister_sja1000dev(dev); - free_sja1000dev(dev); - iounmap(priv->reg_base); - irq_dispose_mapping(dev->irq); - - of_address_to_resource(np, 0, &res); - release_mem_region(res.start, resource_size(&res)); - - return 0; -} - -static int sja1000_ofp_probe(struct platform_device *ofdev) -{ - struct device_node *np = ofdev->dev.of_node; - struct net_device *dev; - struct sja1000_priv *priv; - struct resource res; - u32 prop; - int err, irq, res_size; - void __iomem *base; - - err = of_address_to_resource(np, 0, &res); - if (err) { - dev_err(&ofdev->dev, "invalid address\n"); - return err; - } - - res_size = resource_size(&res); - - if (!request_mem_region(res.start, res_size, DRV_NAME)) { - dev_err(&ofdev->dev, "couldn't request %pR\n", &res); - return -EBUSY; - } - - base = ioremap_nocache(res.start, res_size); - if (!base) { - dev_err(&ofdev->dev, "couldn't ioremap %pR\n", &res); - err = -ENOMEM; - goto exit_release_mem; - } - - irq = irq_of_parse_and_map(np, 0); - if (irq == 0) { - dev_err(&ofdev->dev, "no irq found\n"); - err = -ENODEV; - goto exit_unmap_mem; - } - - dev = alloc_sja1000dev(0); - if (!dev) { - err = -ENOMEM; - goto exit_dispose_irq; - } - - priv = netdev_priv(dev); - - priv->read_reg = sja1000_ofp_read_reg; - priv->write_reg = sja1000_ofp_write_reg; - - err = of_property_read_u32(np, "nxp,external-clock-frequency", &prop); - if (!err) - priv->can.clock.freq = prop / 2; - else - priv->can.clock.freq = SJA1000_OFP_CAN_CLOCK; /* default */ - - err = of_property_read_u32(np, "nxp,tx-output-mode", &prop); - if (!err) - priv->ocr |= prop & OCR_MODE_MASK; - else - priv->ocr |= OCR_MODE_NORMAL; /* default */ - - err = of_property_read_u32(np, "nxp,tx-output-config", &prop); - if (!err) - priv->ocr |= (prop << OCR_TX_SHIFT) & OCR_TX_MASK; - else - priv->ocr |= OCR_TX0_PULLDOWN; /* default */ - - err = of_property_read_u32(np, "nxp,clock-out-frequency", &prop); - if (!err && prop) { - u32 divider = priv->can.clock.freq * 2 / prop; - - if (divider > 1) - priv->cdr |= divider / 2 - 1; - else - priv->cdr |= CDR_CLKOUT_MASK; - } else { - priv->cdr |= CDR_CLK_OFF; /* default */ - } - - if (!of_property_read_bool(np, "nxp,no-comparator-bypass")) - priv->cdr |= CDR_CBP; /* default */ - - priv->irq_flags = IRQF_SHARED; - priv->reg_base = base; - - dev->irq = irq; - - dev_info(&ofdev->dev, - "reg_base=0x%p irq=%d clock=%d ocr=0x%02x cdr=0x%02x\n", - priv->reg_base, dev->irq, priv->can.clock.freq, - priv->ocr, priv->cdr); - - platform_set_drvdata(ofdev, dev); - SET_NETDEV_DEV(dev, &ofdev->dev); - - err = register_sja1000dev(dev); - if (err) { - dev_err(&ofdev->dev, "registering %s failed (err=%d)\n", - DRV_NAME, err); - goto exit_free_sja1000; - } - - return 0; - -exit_free_sja1000: - free_sja1000dev(dev); -exit_dispose_irq: - irq_dispose_mapping(irq); -exit_unmap_mem: - iounmap(base); -exit_release_mem: - release_mem_region(res.start, res_size); - - return err; -} - -static struct of_device_id sja1000_ofp_table[] = { - {.compatible = "nxp,sja1000"}, - {}, -}; -MODULE_DEVICE_TABLE(of, sja1000_ofp_table); - -static struct platform_driver sja1000_ofp_driver = { - .driver = { - .owner = THIS_MODULE, - .name = DRV_NAME, - .of_match_table = sja1000_ofp_table, - }, - .probe = sja1000_ofp_probe, - .remove = sja1000_ofp_remove, -}; - -module_platform_driver(sja1000_ofp_driver); diff --git a/drivers/net/can/sja1000/sja1000_platform.c b/drivers/net/can/sja1000/sja1000_platform.c index 8e259c54103..95a844a7ee7 100644 --- a/drivers/net/can/sja1000/sja1000_platform.c +++ b/drivers/net/can/sja1000/sja1000_platform.c @@ -12,8 +12,7 @@ * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * along with this program; if not, see <http://www.gnu.org/licenses/>. */ #include <linux/kernel.h> @@ -27,12 +26,16 @@ #include <linux/can/dev.h> #include <linux/can/platform/sja1000.h> #include <linux/io.h> +#include <linux/of.h> +#include <linux/of_irq.h> #include "sja1000.h" #define DRV_NAME "sja1000_platform" +#define SP_CAN_CLOCK (16000000 / 2) MODULE_AUTHOR("Sascha Hauer <s.hauer@pengutronix.de>"); +MODULE_AUTHOR("Wolfgang Grandegger <wg@grandegger.com>"); MODULE_DESCRIPTION("Socket-CAN driver for SJA1000 on the platform bus"); MODULE_ALIAS("platform:" DRV_NAME); MODULE_LICENSE("GPL v2"); @@ -67,59 +70,16 @@ static void sp_write_reg32(const struct sja1000_priv *priv, int reg, u8 val) iowrite8(val, priv->reg_base + reg * 4); } -static int sp_probe(struct platform_device *pdev) +static void sp_populate(struct sja1000_priv *priv, + struct sja1000_platform_data *pdata, + unsigned long resource_mem_flags) { - int err; - void __iomem *addr; - struct net_device *dev; - struct sja1000_priv *priv; - struct resource *res_mem, *res_irq; - struct sja1000_platform_data *pdata; - - pdata = pdev->dev.platform_data; - if (!pdata) { - dev_err(&pdev->dev, "No platform data provided!\n"); - err = -ENODEV; - goto exit; - } - - res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); - res_irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0); - if (!res_mem || !res_irq) { - err = -ENODEV; - goto exit; - } - - if (!request_mem_region(res_mem->start, resource_size(res_mem), - DRV_NAME)) { - err = -EBUSY; - goto exit; - } - - addr = ioremap_nocache(res_mem->start, resource_size(res_mem)); - if (!addr) { - err = -ENOMEM; - goto exit_release; - } - - dev = alloc_sja1000dev(0); - if (!dev) { - err = -ENOMEM; - goto exit_iounmap; - } - priv = netdev_priv(dev); - - dev->irq = res_irq->start; - priv->irq_flags = res_irq->flags & IRQF_TRIGGER_MASK; - if (res_irq->flags & IORESOURCE_IRQ_SHAREABLE) - priv->irq_flags |= IRQF_SHARED; - priv->reg_base = addr; /* The CAN clock frequency is half the oscillator clock frequency */ priv->can.clock.freq = pdata->osc_freq / 2; priv->ocr = pdata->ocr; priv->cdr = pdata->cdr; - switch (res_mem->flags & IORESOURCE_MEM_TYPE_MASK) { + switch (resource_mem_flags & IORESOURCE_MEM_TYPE_MASK) { case IORESOURCE_MEM_32BIT: priv->read_reg = sp_read_reg32; priv->write_reg = sp_write_reg32; @@ -134,6 +94,124 @@ static int sp_probe(struct platform_device *pdev) priv->write_reg = sp_write_reg8; break; } +} + +static void sp_populate_of(struct sja1000_priv *priv, struct device_node *of) +{ + int err; + u32 prop; + + err = of_property_read_u32(of, "reg-io-width", &prop); + if (err) + prop = 1; /* 8 bit is default */ + + switch (prop) { + case 4: + priv->read_reg = sp_read_reg32; + priv->write_reg = sp_write_reg32; + break; + case 2: + priv->read_reg = sp_read_reg16; + priv->write_reg = sp_write_reg16; + break; + case 1: /* fallthrough */ + default: + priv->read_reg = sp_read_reg8; + priv->write_reg = sp_write_reg8; + } + + err = of_property_read_u32(of, "nxp,external-clock-frequency", &prop); + if (!err) + priv->can.clock.freq = prop / 2; + else + priv->can.clock.freq = SP_CAN_CLOCK; /* default */ + + err = of_property_read_u32(of, "nxp,tx-output-mode", &prop); + if (!err) + priv->ocr |= prop & OCR_MODE_MASK; + else + priv->ocr |= OCR_MODE_NORMAL; /* default */ + + err = of_property_read_u32(of, "nxp,tx-output-config", &prop); + if (!err) + priv->ocr |= (prop << OCR_TX_SHIFT) & OCR_TX_MASK; + else + priv->ocr |= OCR_TX0_PULLDOWN; /* default */ + + err = of_property_read_u32(of, "nxp,clock-out-frequency", &prop); + if (!err && prop) { + u32 divider = priv->can.clock.freq * 2 / prop; + + if (divider > 1) + priv->cdr |= divider / 2 - 1; + else + priv->cdr |= CDR_CLKOUT_MASK; + } else { + priv->cdr |= CDR_CLK_OFF; /* default */ + } + + if (!of_property_read_bool(of, "nxp,no-comparator-bypass")) + priv->cdr |= CDR_CBP; /* default */ +} + +static int sp_probe(struct platform_device *pdev) +{ + int err, irq = 0; + void __iomem *addr; + struct net_device *dev; + struct sja1000_priv *priv; + struct resource *res_mem, *res_irq = NULL; + struct sja1000_platform_data *pdata; + struct device_node *of = pdev->dev.of_node; + + pdata = dev_get_platdata(&pdev->dev); + if (!pdata && !of) { + dev_err(&pdev->dev, "No platform data provided!\n"); + return -ENODEV; + } + + res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res_mem) + return -ENODEV; + + if (!devm_request_mem_region(&pdev->dev, res_mem->start, + resource_size(res_mem), DRV_NAME)) + return -EBUSY; + + addr = devm_ioremap_nocache(&pdev->dev, res_mem->start, + resource_size(res_mem)); + if (!addr) + return -ENOMEM; + + if (of) + irq = irq_of_parse_and_map(of, 0); + else + res_irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0); + + if (!irq && !res_irq) + return -ENODEV; + + dev = alloc_sja1000dev(0); + if (!dev) + return -ENOMEM; + priv = netdev_priv(dev); + + if (res_irq) { + irq = res_irq->start; + priv->irq_flags = res_irq->flags & IRQF_TRIGGER_MASK; + if (res_irq->flags & IORESOURCE_IRQ_SHAREABLE) + priv->irq_flags |= IRQF_SHARED; + } else { + priv->irq_flags = IRQF_SHARED; + } + + dev->irq = irq; + priv->reg_base = addr; + + if (of) + sp_populate_of(priv, of); + else + sp_populate(priv, pdata, res_mem->flags); platform_set_drvdata(pdev, dev); SET_NETDEV_DEV(dev, &pdev->dev); @@ -151,39 +229,32 @@ static int sp_probe(struct platform_device *pdev) exit_free: free_sja1000dev(dev); - exit_iounmap: - iounmap(addr); - exit_release: - release_mem_region(res_mem->start, resource_size(res_mem)); - exit: return err; } static int sp_remove(struct platform_device *pdev) { struct net_device *dev = platform_get_drvdata(pdev); - struct sja1000_priv *priv = netdev_priv(dev); - struct resource *res; unregister_sja1000dev(dev); - - if (priv->reg_base) - iounmap(priv->reg_base); - - res = platform_get_resource(pdev, IORESOURCE_MEM, 0); - release_mem_region(res->start, resource_size(res)); - free_sja1000dev(dev); return 0; } +static struct of_device_id sp_of_table[] = { + {.compatible = "nxp,sja1000"}, + {}, +}; +MODULE_DEVICE_TABLE(of, sp_of_table); + static struct platform_driver sp_driver = { .probe = sp_probe, .remove = sp_remove, .driver = { .name = DRV_NAME, .owner = THIS_MODULE, + .of_match_table = sp_of_table, }, }; diff --git a/drivers/net/can/slcan.c b/drivers/net/can/slcan.c index 25377e547f9..ea4d4f1a641 100644 --- a/drivers/net/can/slcan.c +++ b/drivers/net/can/slcan.c @@ -18,9 +18,7 @@ * General Public License for more details. * * You should have received a copy of the GNU General Public License along - * with this program; if not, write to the Free Software Foundation, Inc., - * 59 Temple Place, Suite 330, Boston, MA 02111-1307. You can also get it - * at http://www.gnu.org/licenses/gpl.html + * with this program; if not, see http://www.gnu.org/licenses/gpl.html * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT @@ -54,6 +52,7 @@ #include <linux/delay.h> #include <linux/init.h> #include <linux/kernel.h> +#include <linux/workqueue.h> #include <linux/can.h> #include <linux/can/skb.h> @@ -87,6 +86,7 @@ struct slcan { struct tty_struct *tty; /* ptr to TTY structure */ struct net_device *dev; /* easy for intr handling */ spinlock_t lock; + struct work_struct tx_work; /* Flushes transmit buffer */ /* These are pointers to the malloc()ed frame buffers. */ unsigned char rbuff[SLC_MTU]; /* receiver buffer */ @@ -311,34 +311,44 @@ static void slc_encaps(struct slcan *sl, struct can_frame *cf) sl->dev->stats.tx_bytes += cf->can_dlc; } -/* - * Called by the driver when there's room for more data. If we have - * more packets to send, we send them here. - */ -static void slcan_write_wakeup(struct tty_struct *tty) +/* Write out any remaining transmit buffer. Scheduled when tty is writable */ +static void slcan_transmit(struct work_struct *work) { + struct slcan *sl = container_of(work, struct slcan, tx_work); int actual; - struct slcan *sl = (struct slcan *) tty->disc_data; + spin_lock_bh(&sl->lock); /* First make sure we're connected. */ - if (!sl || sl->magic != SLCAN_MAGIC || !netif_running(sl->dev)) + if (!sl->tty || sl->magic != SLCAN_MAGIC || !netif_running(sl->dev)) { + spin_unlock_bh(&sl->lock); return; + } - spin_lock(&sl->lock); if (sl->xleft <= 0) { /* Now serial buffer is almost free & we can start * transmission of another packet */ sl->dev->stats.tx_packets++; - clear_bit(TTY_DO_WRITE_WAKEUP, &tty->flags); - spin_unlock(&sl->lock); + clear_bit(TTY_DO_WRITE_WAKEUP, &sl->tty->flags); + spin_unlock_bh(&sl->lock); netif_wake_queue(sl->dev); return; } - actual = tty->ops->write(tty, sl->xhead, sl->xleft); + actual = sl->tty->ops->write(sl->tty, sl->xhead, sl->xleft); sl->xleft -= actual; sl->xhead += actual; - spin_unlock(&sl->lock); + spin_unlock_bh(&sl->lock); +} + +/* + * Called by the driver when there's room for more data. + * Schedule the transmit. + */ +static void slcan_write_wakeup(struct tty_struct *tty) +{ + struct slcan *sl = tty->disc_data; + + schedule_work(&sl->tx_work); } /* Send a can_frame to a TTY queue. */ @@ -413,10 +423,16 @@ static void slc_free_netdev(struct net_device *dev) slcan_devs[i] = NULL; } +static int slcan_change_mtu(struct net_device *dev, int new_mtu) +{ + return -EINVAL; +} + static const struct net_device_ops slc_netdev_ops = { .ndo_open = slc_open, .ndo_stop = slc_close, .ndo_start_xmit = slc_xmit, + .ndo_change_mtu = slcan_change_mtu, }; static void slc_setup(struct net_device *dev) @@ -524,6 +540,7 @@ static struct slcan *slc_alloc(dev_t line) sl->magic = SLCAN_MAGIC; sl->dev = dev; spin_lock_init(&sl->lock); + INIT_WORK(&sl->tx_work, slcan_transmit); slcan_devs[i] = dev; return sl; @@ -622,8 +639,12 @@ static void slcan_close(struct tty_struct *tty) if (!sl || sl->magic != SLCAN_MAGIC || sl->tty != tty) return; + spin_lock_bh(&sl->lock); tty->disc_data = NULL; sl->tty = NULL; + spin_unlock_bh(&sl->lock); + + flush_work(&sl->tx_work); /* Flush network side */ unregister_netdev(sl->dev); diff --git a/drivers/net/can/softing/softing.h b/drivers/net/can/softing/softing.h index afd7d85b691..35f062282db 100644 --- a/drivers/net/can/softing/softing.h +++ b/drivers/net/can/softing/softing.h @@ -71,34 +71,34 @@ struct softing { } id; }; -extern int softing_default_output(struct net_device *netdev); +int softing_default_output(struct net_device *netdev); -extern ktime_t softing_raw2ktime(struct softing *card, u32 raw); +ktime_t softing_raw2ktime(struct softing *card, u32 raw); -extern int softing_chip_poweron(struct softing *card); +int softing_chip_poweron(struct softing *card); -extern int softing_bootloader_command(struct softing *card, int16_t cmd, - const char *msg); +int softing_bootloader_command(struct softing *card, int16_t cmd, + const char *msg); /* Load firmware after reset */ -extern int softing_load_fw(const char *file, struct softing *card, - __iomem uint8_t *virt, unsigned int size, int offset); +int softing_load_fw(const char *file, struct softing *card, + __iomem uint8_t *virt, unsigned int size, int offset); /* Load final application firmware after bootloader */ -extern int softing_load_app_fw(const char *file, struct softing *card); +int softing_load_app_fw(const char *file, struct softing *card); /* * enable or disable irq * only called with fw.lock locked */ -extern int softing_enable_irq(struct softing *card, int enable); +int softing_enable_irq(struct softing *card, int enable); /* start/stop 1 bus on card */ -extern int softing_startstop(struct net_device *netdev, int up); +int softing_startstop(struct net_device *netdev, int up); /* netif_rx() */ -extern int softing_netdev_rx(struct net_device *netdev, - const struct can_frame *msg, ktime_t ktime); +int softing_netdev_rx(struct net_device *netdev, const struct can_frame *msg, + ktime_t ktime); /* SOFTING DPRAM mappings */ #define DPRAM_RX 0x0000 diff --git a/drivers/net/can/softing/softing_cs.c b/drivers/net/can/softing/softing_cs.c index 498605f833d..cdc0c7433a4 100644 --- a/drivers/net/can/softing/softing_cs.c +++ b/drivers/net/can/softing/softing_cs.c @@ -13,8 +13,7 @@ * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * along with this program; if not, see <http://www.gnu.org/licenses/>. */ #include <linux/module.h> diff --git a/drivers/net/can/softing/softing_fw.c b/drivers/net/can/softing/softing_fw.c index b595d3422b9..52fe50725d7 100644 --- a/drivers/net/can/softing/softing_fw.c +++ b/drivers/net/can/softing/softing_fw.c @@ -13,8 +13,7 @@ * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * along with this program; if not, see <http://www.gnu.org/licenses/>. */ #include <linux/firmware.h> diff --git a/drivers/net/can/softing/softing_main.c b/drivers/net/can/softing/softing_main.c index 65eef1eea2e..bacd236ce30 100644 --- a/drivers/net/can/softing/softing_main.c +++ b/drivers/net/can/softing/softing_main.c @@ -13,12 +13,10 @@ * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * along with this program; if not, see <http://www.gnu.org/licenses/>. */ #include <linux/module.h> -#include <linux/init.h> #include <linux/interrupt.h> #include <asm/io.h> @@ -558,15 +556,6 @@ failed: /* * netdev sysfs */ -static ssize_t show_channel(struct device *dev, struct device_attribute *attr, - char *buf) -{ - struct net_device *ndev = to_net_dev(dev); - struct softing_priv *priv = netdev2softing(ndev); - - return sprintf(buf, "%i\n", priv->index); -} - static ssize_t show_chip(struct device *dev, struct device_attribute *attr, char *buf) { @@ -611,12 +600,10 @@ static ssize_t store_output(struct device *dev, struct device_attribute *attr, return count; } -static const DEVICE_ATTR(channel, S_IRUGO, show_channel, NULL); static const DEVICE_ATTR(chip, S_IRUGO, show_chip, NULL); static const DEVICE_ATTR(output, S_IRUGO | S_IWUSR, show_output, store_output); static const struct attribute *const netdev_sysfs_attrs[] = { - &dev_attr_channel.attr, &dev_attr_chip.attr, &dev_attr_output.attr, NULL, @@ -630,6 +617,7 @@ static const struct net_device_ops softing_netdev_ops = { .ndo_open = softing_netdev_open, .ndo_stop = softing_netdev_stop, .ndo_start_xmit = softing_netdev_start_xmit, + .ndo_change_mtu = can_change_mtu, }; static const struct can_bittiming_const softing_btr_const = { @@ -680,17 +668,20 @@ static int softing_netdev_register(struct net_device *netdev) { int ret; - netdev->sysfs_groups[0] = &netdev_sysfs_group; ret = register_candev(netdev); if (ret) { dev_alert(&netdev->dev, "register failed\n"); return ret; } + if (sysfs_create_group(&netdev->dev.kobj, &netdev_sysfs_group) < 0) + netdev_alert(netdev, "sysfs group failed\n"); + return 0; } static void softing_netdev_cleanup(struct net_device *netdev) { + sysfs_remove_group(&netdev->dev.kobj, &netdev_sysfs_group); unregister_candev(netdev); free_candev(netdev); } @@ -722,8 +713,6 @@ DEV_ATTR_RO(firmware_version, id.fw_version); DEV_ATTR_RO_STR(hardware, pdat->name); DEV_ATTR_RO(hardware_version, id.hw_version); DEV_ATTR_RO(license, id.license); -DEV_ATTR_RO(frequency, id.freq); -DEV_ATTR_RO(txpending, tx.pending); static struct attribute *softing_pdev_attrs[] = { &dev_attr_serial.attr, @@ -732,8 +721,6 @@ static struct attribute *softing_pdev_attrs[] = { &dev_attr_hardware.attr, &dev_attr_hardware_version.attr, &dev_attr_license.attr, - &dev_attr_frequency.attr, - &dev_attr_txpending.attr, NULL, }; @@ -768,7 +755,7 @@ static int softing_pdev_remove(struct platform_device *pdev) static int softing_pdev_probe(struct platform_device *pdev) { - const struct softing_platform_data *pdat = pdev->dev.platform_data; + const struct softing_platform_data *pdat = dev_get_platdata(&pdev->dev); struct softing *card; struct net_device *netdev; struct softing_priv *priv; @@ -834,6 +821,7 @@ static int softing_pdev_probe(struct platform_device *pdev) ret = -ENOMEM; goto netdev_failed; } + netdev->dev_id = j; priv = netdev_priv(card->net[j]); priv->index = j; ret = softing_netdev_register(netdev); diff --git a/drivers/net/can/spi/Kconfig b/drivers/net/can/spi/Kconfig new file mode 100644 index 00000000000..148cae5871a --- /dev/null +++ b/drivers/net/can/spi/Kconfig @@ -0,0 +1,10 @@ +menu "CAN SPI interfaces" + depends on SPI + +config CAN_MCP251X + tristate "Microchip MCP251x SPI CAN controllers" + depends on HAS_DMA + ---help--- + Driver for the Microchip MCP251x SPI CAN controllers. + +endmenu diff --git a/drivers/net/can/spi/Makefile b/drivers/net/can/spi/Makefile new file mode 100644 index 00000000000..90bcacffbc6 --- /dev/null +++ b/drivers/net/can/spi/Makefile @@ -0,0 +1,8 @@ +# +# Makefile for the Linux Controller Area Network SPI drivers. +# + + +obj-$(CONFIG_CAN_MCP251X) += mcp251x.o + +ccflags-$(CONFIG_CAN_DEBUG_DEVICES) := -DDEBUG diff --git a/drivers/net/can/mcp251x.c b/drivers/net/can/spi/mcp251x.c index fe7dd696957..5df239e6881 100644 --- a/drivers/net/can/mcp251x.c +++ b/drivers/net/can/spi/mcp251x.c @@ -28,8 +28,7 @@ * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * along with this program; if not, see <http://www.gnu.org/licenses/>. * * * @@ -59,6 +58,7 @@ #include <linux/can/dev.h> #include <linux/can/led.h> #include <linux/can/platform/mcp251x.h> +#include <linux/clk.h> #include <linux/completion.h> #include <linux/delay.h> #include <linux/device.h> @@ -69,6 +69,8 @@ #include <linux/kernel.h> #include <linux/module.h> #include <linux/netdevice.h> +#include <linux/of.h> +#include <linux/of_device.h> #include <linux/platform_device.h> #include <linux/slab.h> #include <linux/spi/spi.h> @@ -212,6 +214,8 @@ #define TX_ECHO_SKB_MAX 1 +#define MCP251X_OST_DELAY_MS (5) + #define DEVICE_NAME "mcp251x" static int mcp251x_enable_dma; /* Enable SPI DMA. Default: 0 (Off) */ @@ -264,6 +268,7 @@ struct mcp251x_priv { int restart_tx; struct regulator *power; struct regulator *transceiver; + struct clk *clk; }; #define MCP251X_IS(_model) \ @@ -598,10 +603,10 @@ static int mcp251x_do_set_bittiming(struct net_device *net) (bt->prop_seg - 1)); mcp251x_write_bits(spi, CNF3, CNF3_PHSEG2_MASK, (bt->phase_seg2 - 1)); - dev_info(&spi->dev, "CNF: 0x%02x 0x%02x 0x%02x\n", - mcp251x_read_reg(spi, CNF1), - mcp251x_read_reg(spi, CNF2), - mcp251x_read_reg(spi, CNF3)); + dev_dbg(&spi->dev, "CNF: 0x%02x 0x%02x 0x%02x\n", + mcp251x_read_reg(spi, CNF1), + mcp251x_read_reg(spi, CNF2), + mcp251x_read_reg(spi, CNF3)); return 0; } @@ -621,55 +626,50 @@ static int mcp251x_setup(struct net_device *net, struct mcp251x_priv *priv, static int mcp251x_hw_reset(struct spi_device *spi) { struct mcp251x_priv *priv = spi_get_drvdata(spi); + u8 reg; int ret; - unsigned long timeout; + + /* Wait for oscillator startup timer after power up */ + mdelay(MCP251X_OST_DELAY_MS); priv->spi_tx_buf[0] = INSTRUCTION_RESET; - ret = spi_write(spi, priv->spi_tx_buf, 1); - if (ret) { - dev_err(&spi->dev, "reset failed: ret = %d\n", ret); - return -EIO; - } + ret = mcp251x_spi_trans(spi, 1); + if (ret) + return ret; + + /* Wait for oscillator startup timer after reset */ + mdelay(MCP251X_OST_DELAY_MS); + + reg = mcp251x_read_reg(spi, CANSTAT); + if ((reg & CANCTRL_REQOP_MASK) != CANCTRL_REQOP_CONF) + return -ENODEV; - /* Wait for reset to finish */ - timeout = jiffies + HZ; - mdelay(10); - while ((mcp251x_read_reg(spi, CANSTAT) & CANCTRL_REQOP_MASK) - != CANCTRL_REQOP_CONF) { - schedule(); - if (time_after(jiffies, timeout)) { - dev_err(&spi->dev, "MCP251x didn't" - " enter in conf mode after reset\n"); - return -EBUSY; - } - } return 0; } static int mcp251x_hw_probe(struct spi_device *spi) { - int st1, st2; + u8 ctrl; + int ret; - mcp251x_hw_reset(spi); + ret = mcp251x_hw_reset(spi); + if (ret) + return ret; - /* - * Please note that these are "magic values" based on after - * reset defaults taken from data sheet which allows us to see - * if we really have a chip on the bus (we avoid common all - * zeroes or all ones situations) - */ - st1 = mcp251x_read_reg(spi, CANSTAT) & 0xEE; - st2 = mcp251x_read_reg(spi, CANCTRL) & 0x17; + ctrl = mcp251x_read_reg(spi, CANCTRL); - dev_dbg(&spi->dev, "CANSTAT 0x%02x CANCTRL 0x%02x\n", st1, st2); + dev_dbg(&spi->dev, "CANCTRL 0x%02x\n", ctrl); - /* Check for power up default values */ - return (st1 == 0x80 && st2 == 0x07) ? 1 : 0; + /* Check for power up default value */ + if ((ctrl & 0x17) != 0x07) + return -ENODEV; + + return 0; } static int mcp251x_power_enable(struct regulator *reg, int enable) { - if (IS_ERR(reg)) + if (IS_ERR_OR_NULL(reg)) return 0; if (enable) @@ -773,7 +773,6 @@ static void mcp251x_restart_work_handler(struct work_struct *ws) mutex_lock(&priv->mcp_lock); if (priv->after_suspend) { - mdelay(10); mcp251x_hw_reset(spi); mcp251x_setup(net, priv, spi); if (priv->after_suspend & AFTER_SUSPEND_RESTART) { @@ -952,7 +951,7 @@ static int mcp251x_open(struct net_device *net) priv->tx_len = 0; ret = request_threaded_irq(spi->irq, NULL, mcp251x_can_ist, - flags, DEVICE_NAME, priv); + flags | IRQF_ONESHOT, DEVICE_NAME, priv); if (ret) { dev_err(&spi->dev, "failed to acquire irq %d\n", spi->irq); mcp251x_power_enable(priv->transceiver, 0); @@ -993,24 +992,68 @@ static const struct net_device_ops mcp251x_netdev_ops = { .ndo_open = mcp251x_open, .ndo_stop = mcp251x_stop, .ndo_start_xmit = mcp251x_hard_start_xmit, + .ndo_change_mtu = can_change_mtu, }; +static const struct of_device_id mcp251x_of_match[] = { + { + .compatible = "microchip,mcp2510", + .data = (void *)CAN_MCP251X_MCP2510, + }, + { + .compatible = "microchip,mcp2515", + .data = (void *)CAN_MCP251X_MCP2515, + }, + { } +}; +MODULE_DEVICE_TABLE(of, mcp251x_of_match); + +static const struct spi_device_id mcp251x_id_table[] = { + { + .name = "mcp2510", + .driver_data = (kernel_ulong_t)CAN_MCP251X_MCP2510, + }, + { + .name = "mcp2515", + .driver_data = (kernel_ulong_t)CAN_MCP251X_MCP2515, + }, + { } +}; +MODULE_DEVICE_TABLE(spi, mcp251x_id_table); + static int mcp251x_can_probe(struct spi_device *spi) { + const struct of_device_id *of_id = of_match_device(mcp251x_of_match, + &spi->dev); + struct mcp251x_platform_data *pdata = dev_get_platdata(&spi->dev); struct net_device *net; struct mcp251x_priv *priv; - struct mcp251x_platform_data *pdata = spi->dev.platform_data; - int ret = -ENODEV; + struct clk *clk; + int freq, ret; + + clk = devm_clk_get(&spi->dev, NULL); + if (IS_ERR(clk)) { + if (pdata) + freq = pdata->oscillator_frequency; + else + return PTR_ERR(clk); + } else { + freq = clk_get_rate(clk); + } - if (!pdata) - /* Platform data is required for osc freq */ - goto error_out; + /* Sanity check */ + if (freq < 1000000 || freq > 25000000) + return -ERANGE; /* Allocate can/net device */ net = alloc_candev(sizeof(struct mcp251x_priv), TX_ECHO_SKB_MAX); - if (!net) { - ret = -ENOMEM; - goto error_alloc; + if (!net) + return -ENOMEM; + + if (!IS_ERR(clk)) { + ret = clk_prepare_enable(clk); + if (ret) + goto out_free; } net->netdev_ops = &mcp251x_netdev_ops; @@ -1019,25 +1062,39 @@ static int mcp251x_can_probe(struct spi_device *spi) priv = netdev_priv(net); priv->can.bittiming_const = &mcp251x_bittiming_const; priv->can.do_set_mode = mcp251x_do_set_mode; - priv->can.clock.freq = pdata->oscillator_frequency / 2; + priv->can.clock.freq = freq / 2; priv->can.ctrlmode_supported = CAN_CTRLMODE_3_SAMPLES | CAN_CTRLMODE_LOOPBACK | CAN_CTRLMODE_LISTENONLY; - priv->model = spi_get_device_id(spi)->driver_data; + if (of_id) + priv->model = (enum mcp251x_model)of_id->data; + else + priv->model = spi_get_device_id(spi)->driver_data; priv->net = net; + priv->clk = clk; + + spi_set_drvdata(spi, priv); + + /* Configure the SPI bus */ + spi->bits_per_word = 8; + if (mcp251x_is_2510(spi)) + spi->max_speed_hz = spi->max_speed_hz ? : 5 * 1000 * 1000; + else + spi->max_speed_hz = spi->max_speed_hz ? : 10 * 1000 * 1000; + ret = spi_setup(spi); + if (ret) + goto out_clk; priv->power = devm_regulator_get(&spi->dev, "vdd"); priv->transceiver = devm_regulator_get(&spi->dev, "xceiver"); if ((PTR_ERR(priv->power) == -EPROBE_DEFER) || (PTR_ERR(priv->transceiver) == -EPROBE_DEFER)) { ret = -EPROBE_DEFER; - goto error_power; + goto out_clk; } ret = mcp251x_power_enable(priv->power, 1); if (ret) - goto error_power; - - spi_set_drvdata(spi, priv); + goto out_clk; priv->spi = spi; mutex_init(&priv->mcp_lock); @@ -1067,34 +1124,27 @@ static int mcp251x_can_probe(struct spi_device *spi) /* Allocate non-DMA buffers */ if (!mcp251x_enable_dma) { - priv->spi_tx_buf = kmalloc(SPI_TRANSFER_BUF_LEN, GFP_KERNEL); + priv->spi_tx_buf = devm_kzalloc(&spi->dev, SPI_TRANSFER_BUF_LEN, + GFP_KERNEL); if (!priv->spi_tx_buf) { ret = -ENOMEM; - goto error_tx_buf; + goto error_probe; } - priv->spi_rx_buf = kmalloc(SPI_TRANSFER_BUF_LEN, GFP_KERNEL); + priv->spi_rx_buf = devm_kzalloc(&spi->dev, SPI_TRANSFER_BUF_LEN, + GFP_KERNEL); if (!priv->spi_rx_buf) { ret = -ENOMEM; - goto error_rx_buf; + goto error_probe; } } SET_NETDEV_DEV(net, &spi->dev); - /* Configure the SPI bus */ - spi->mode = spi->mode ? : SPI_MODE_0; - if (mcp251x_is_2510(spi)) - spi->max_speed_hz = spi->max_speed_hz ? : 5 * 1000 * 1000; - else - spi->max_speed_hz = spi->max_speed_hz ? : 10 * 1000 * 1000; - spi->bits_per_word = 8; - spi_setup(spi); - /* Here is OK to not lock the MCP, no one knows about it yet */ - if (!mcp251x_hw_probe(spi)) { - ret = -ENODEV; + ret = mcp251x_hw_probe(spi); + if (ret) goto error_probe; - } + mcp251x_hw_sleep(spi); ret = register_candev(net); @@ -1103,26 +1153,21 @@ static int mcp251x_can_probe(struct spi_device *spi) devm_can_led_init(net); - dev_info(&spi->dev, "probed\n"); - - return ret; + return 0; error_probe: - if (!mcp251x_enable_dma) - kfree(priv->spi_rx_buf); -error_rx_buf: - if (!mcp251x_enable_dma) - kfree(priv->spi_tx_buf); -error_tx_buf: if (mcp251x_enable_dma) dma_free_coherent(&spi->dev, PAGE_SIZE, priv->spi_tx_buf, priv->spi_tx_dma); mcp251x_power_enable(priv->power, 0); -error_power: + +out_clk: + if (!IS_ERR(clk)) + clk_disable_unprepare(clk); + +out_free: free_candev(net); -error_alloc: - dev_err(&spi->dev, "probe failed\n"); -error_out: + return ret; } @@ -1136,21 +1181,19 @@ static int mcp251x_can_remove(struct spi_device *spi) if (mcp251x_enable_dma) { dma_free_coherent(&spi->dev, PAGE_SIZE, priv->spi_tx_buf, priv->spi_tx_dma); - } else { - kfree(priv->spi_tx_buf); - kfree(priv->spi_rx_buf); } mcp251x_power_enable(priv->power, 0); + if (!IS_ERR(priv->clk)) + clk_disable_unprepare(priv->clk); + free_candev(net); return 0; } -#ifdef CONFIG_PM_SLEEP - -static int mcp251x_can_suspend(struct device *dev) +static int __maybe_unused mcp251x_can_suspend(struct device *dev) { struct spi_device *spi = to_spi_device(dev); struct mcp251x_priv *priv = spi_get_drvdata(spi); @@ -1172,7 +1215,7 @@ static int mcp251x_can_suspend(struct device *dev) priv->after_suspend = AFTER_SUSPEND_DOWN; } - if (!IS_ERR(priv->power)) { + if (!IS_ERR_OR_NULL(priv->power)) { regulator_disable(priv->power); priv->after_suspend |= AFTER_SUSPEND_POWER; } @@ -1180,7 +1223,7 @@ static int mcp251x_can_suspend(struct device *dev) return 0; } -static int mcp251x_can_resume(struct device *dev) +static int __maybe_unused mcp251x_can_resume(struct device *dev) { struct spi_device *spi = to_spi_device(dev); struct mcp251x_priv *priv = spi_get_drvdata(spi); @@ -1200,26 +1243,17 @@ static int mcp251x_can_resume(struct device *dev) enable_irq(spi->irq); return 0; } -#endif static SIMPLE_DEV_PM_OPS(mcp251x_can_pm_ops, mcp251x_can_suspend, mcp251x_can_resume); -static const struct spi_device_id mcp251x_id_table[] = { - { "mcp2510", CAN_MCP251X_MCP2510 }, - { "mcp2515", CAN_MCP251X_MCP2515 }, - { }, -}; - -MODULE_DEVICE_TABLE(spi, mcp251x_id_table); - static struct spi_driver mcp251x_can_driver = { .driver = { .name = DEVICE_NAME, .owner = THIS_MODULE, + .of_match_table = mcp251x_of_match, .pm = &mcp251x_can_pm_ops, }, - .id_table = mcp251x_id_table, .probe = mcp251x_can_probe, .remove = mcp251x_can_remove, diff --git a/drivers/net/can/ti_hecc.c b/drivers/net/can/ti_hecc.c index 3a349a22d5b..258b9c4856e 100644 --- a/drivers/net/can/ti_hecc.c +++ b/drivers/net/can/ti_hecc.c @@ -37,7 +37,6 @@ */ #include <linux/module.h> -#include <linux/init.h> #include <linux/kernel.h> #include <linux/types.h> #include <linux/interrupt.h> @@ -286,15 +285,6 @@ static inline u32 hecc_get_bit(struct ti_hecc_priv *priv, int reg, u32 bit_mask) return (hecc_read(priv, reg) & bit_mask) ? 1 : 0; } -static int ti_hecc_get_state(const struct net_device *ndev, - enum can_state *state) -{ - struct ti_hecc_priv *priv = netdev_priv(ndev); - - *state = priv->can.state; - return 0; -} - static int ti_hecc_set_btc(struct ti_hecc_priv *priv) { struct can_bittiming *bit_timing = &priv->can.bittiming; @@ -527,10 +517,10 @@ static netdev_tx_t ti_hecc_xmit(struct sk_buff *skb, struct net_device *ndev) data = (cf->can_id & CAN_SFF_MASK) << 18; hecc_write_mbx(priv, mbxno, HECC_CANMID, data); hecc_write_mbx(priv, mbxno, HECC_CANMDL, - be32_to_cpu(*(u32 *)(cf->data))); + be32_to_cpu(*(__be32 *)(cf->data))); if (cf->can_dlc > 4) hecc_write_mbx(priv, mbxno, HECC_CANMDH, - be32_to_cpu(*(u32 *)(cf->data + 4))); + be32_to_cpu(*(__be32 *)(cf->data + 4))); else *(u32 *)(cf->data + 4) = 0; can_put_echo_skb(skb, ndev, mbxno); @@ -578,12 +568,10 @@ static int ti_hecc_rx_pkt(struct ti_hecc_priv *priv, int mbxno) cf->can_id |= CAN_RTR_FLAG; cf->can_dlc = get_can_dlc(data & 0xF); data = hecc_read_mbx(priv, mbxno, HECC_CANMDL); - *(u32 *)(cf->data) = cpu_to_be32(data); + *(__be32 *)(cf->data) = cpu_to_be32(data); if (cf->can_dlc > 4) { data = hecc_read_mbx(priv, mbxno, HECC_CANMDH); - *(u32 *)(cf->data + 4) = cpu_to_be32(data); - } else { - *(u32 *)(cf->data + 4) = 0; + *(__be32 *)(cf->data + 4) = cpu_to_be32(data); } spin_lock_irqsave(&priv->mbx_lock, flags); hecc_clear_bit(priv, HECC_CANME, mbx_mask); @@ -883,6 +871,7 @@ static const struct net_device_ops ti_hecc_netdev_ops = { .ndo_open = ti_hecc_open, .ndo_stop = ti_hecc_close, .ndo_start_xmit = ti_hecc_xmit, + .ndo_change_mtu = can_change_mtu, }; static int ti_hecc_probe(struct platform_device *pdev) @@ -894,7 +883,7 @@ static int ti_hecc_probe(struct platform_device *pdev) void __iomem *addr; int err = -ENODEV; - pdata = pdev->dev.platform_data; + pdata = dev_get_platdata(&pdev->dev); if (!pdata) { dev_err(&pdev->dev, "No platform data\n"); goto probe_exit; @@ -940,7 +929,6 @@ static int ti_hecc_probe(struct platform_device *pdev) priv->can.bittiming_const = &ti_hecc_bittiming_const; priv->can.do_set_mode = ti_hecc_do_set_mode; - priv->can.do_get_state = ti_hecc_get_state; priv->can.do_get_berr_counter = ti_hecc_get_berr_counter; priv->can.ctrlmode_supported = CAN_CTRLMODE_3_SAMPLES; diff --git a/drivers/net/can/usb/Kconfig b/drivers/net/can/usb/Kconfig index fc96a3d83eb..a77db919363 100644 --- a/drivers/net/can/usb/Kconfig +++ b/drivers/net/can/usb/Kconfig @@ -13,13 +13,21 @@ config CAN_ESD_USB2 This driver supports the CAN-USB/2 interface from esd electronic system design gmbh (http://www.esd.eu). +config CAN_GS_USB + tristate "Geschwister Schneider UG interfaces" + ---help--- + This driver supports the Geschwister Schneider USB/CAN devices. + If unsure choose N, + choose Y for built in support, + M to compile as module (module will be named: gs_usb). + config CAN_KVASER_USB tristate "Kvaser CAN/USB interface" ---help--- This driver adds support for Kvaser CAN/USB devices like Kvaser Leaf Light. - The driver gives support for the following devices: + The driver provides support for the following devices: - Kvaser Leaf Light - Kvaser Leaf Professional HS - Kvaser Leaf SemiPro HS @@ -36,6 +44,8 @@ config CAN_KVASER_USB - Kvaser Leaf Light "China" - Kvaser BlackBird SemiPro - Kvaser USBcan R + - Kvaser Leaf Light v2 + - Kvaser Mini PCI Express HS If unsure, say N. diff --git a/drivers/net/can/usb/Makefile b/drivers/net/can/usb/Makefile index becef460a91..7b9a393b1ac 100644 --- a/drivers/net/can/usb/Makefile +++ b/drivers/net/can/usb/Makefile @@ -4,6 +4,7 @@ obj-$(CONFIG_CAN_EMS_USB) += ems_usb.o obj-$(CONFIG_CAN_ESD_USB2) += esd_usb2.o +obj-$(CONFIG_CAN_GS_USB) += gs_usb.o obj-$(CONFIG_CAN_KVASER_USB) += kvaser_usb.o obj-$(CONFIG_CAN_PEAK_USB) += peak_usb/ obj-$(CONFIG_CAN_8DEV_USB) += usb_8dev.o diff --git a/drivers/net/can/usb/ems_usb.c b/drivers/net/can/usb/ems_usb.c index 5f9a7ad9b96..00f2534dde7 100644 --- a/drivers/net/can/usb/ems_usb.c +++ b/drivers/net/can/usb/ems_usb.c @@ -16,7 +16,6 @@ * with this program; if not, write to the Free Software Foundation, Inc., * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA. */ -#include <linux/init.h> #include <linux/signal.h> #include <linux/slab.h> #include <linux/module.h> @@ -625,6 +624,7 @@ static int ems_usb_start(struct ems_usb *dev) usb_unanchor_urb(urb); usb_free_coherent(dev->udev, RX_BUFFER_SIZE, buf, urb->transfer_dma); + usb_free_urb(urb); break; } @@ -798,8 +798,8 @@ static netdev_tx_t ems_usb_start_xmit(struct sk_buff *skb, struct net_device *ne * allowed (MAX_TX_URBS). */ if (!context) { - usb_unanchor_urb(urb); usb_free_coherent(dev->udev, size, buf, urb->transfer_dma); + usb_free_urb(urb); netdev_warn(netdev, "couldn't find free context\n"); @@ -883,6 +883,7 @@ static const struct net_device_ops ems_usb_netdev_ops = { .ndo_open = ems_usb_open, .ndo_stop = ems_usb_close, .ndo_start_xmit = ems_usb_start_xmit, + .ndo_change_mtu = can_change_mtu, }; static const struct can_bittiming_const ems_usb_bittiming_const = { diff --git a/drivers/net/can/usb/esd_usb2.c b/drivers/net/can/usb/esd_usb2.c index ac6177d3bef..b7c9e8b1146 100644 --- a/drivers/net/can/usb/esd_usb2.c +++ b/drivers/net/can/usb/esd_usb2.c @@ -16,7 +16,6 @@ * with this program; if not, write to the Free Software Foundation, Inc., * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA. */ -#include <linux/init.h> #include <linux/signal.h> #include <linux/slab.h> #include <linux/module.h> @@ -889,6 +888,7 @@ static const struct net_device_ops esd_usb2_netdev_ops = { .ndo_open = esd_usb2_open, .ndo_stop = esd_usb2_close, .ndo_start_xmit = esd_usb2_start_xmit, + .ndo_change_mtu = can_change_mtu, }; static const struct can_bittiming_const esd_usb2_bittiming_const = { @@ -1025,6 +1025,7 @@ static int esd_usb2_probe_one_net(struct usb_interface *intf, int index) netdev->netdev_ops = &esd_usb2_netdev_ops; SET_NETDEV_DEV(netdev, &intf->dev); + netdev->dev_id = index; err = register_candev(netdev); if (err) { diff --git a/drivers/net/can/usb/gs_usb.c b/drivers/net/can/usb/gs_usb.c new file mode 100644 index 00000000000..04b0f84612f --- /dev/null +++ b/drivers/net/can/usb/gs_usb.c @@ -0,0 +1,971 @@ +/* CAN driver for Geschwister Schneider USB/CAN devices. + * + * Copyright (C) 2013 Geschwister Schneider Technologie-, + * Entwicklungs- und Vertriebs UG (Haftungsbeschränkt). + * + * Many thanks to all socketcan devs! + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published + * by the Free Software Foundation; version 2 of the License. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + */ + +#include <linux/init.h> +#include <linux/signal.h> +#include <linux/module.h> +#include <linux/netdevice.h> +#include <linux/usb.h> + +#include <linux/can.h> +#include <linux/can/dev.h> +#include <linux/can/error.h> + +/* Device specific constants */ +#define USB_GSUSB_1_VENDOR_ID 0x1d50 +#define USB_GSUSB_1_PRODUCT_ID 0x606f + +#define GSUSB_ENDPOINT_IN 1 +#define GSUSB_ENDPOINT_OUT 2 + +/* Device specific constants */ +enum gs_usb_breq { + GS_USB_BREQ_HOST_FORMAT = 0, + GS_USB_BREQ_BITTIMING, + GS_USB_BREQ_MODE, + GS_USB_BREQ_BERR, + GS_USB_BREQ_BT_CONST, + GS_USB_BREQ_DEVICE_CONFIG +}; + +enum gs_can_mode { + /* reset a channel. turns it off */ + GS_CAN_MODE_RESET = 0, + /* starts a channel */ + GS_CAN_MODE_START +}; + +enum gs_can_state { + GS_CAN_STATE_ERROR_ACTIVE = 0, + GS_CAN_STATE_ERROR_WARNING, + GS_CAN_STATE_ERROR_PASSIVE, + GS_CAN_STATE_BUS_OFF, + GS_CAN_STATE_STOPPED, + GS_CAN_STATE_SLEEPING +}; + +/* data types passed between host and device */ +struct gs_host_config { + u32 byte_order; +} __packed; +/* All data exchanged between host and device is exchanged in host byte order, + * thanks to the struct gs_host_config byte_order member, which is sent first + * to indicate the desired byte order. + */ + +struct gs_device_config { + u8 reserved1; + u8 reserved2; + u8 reserved3; + u8 icount; + u32 sw_version; + u32 hw_version; +} __packed; + +#define GS_CAN_MODE_NORMAL 0 +#define GS_CAN_MODE_LISTEN_ONLY (1<<0) +#define GS_CAN_MODE_LOOP_BACK (1<<1) +#define GS_CAN_MODE_TRIPLE_SAMPLE (1<<2) +#define GS_CAN_MODE_ONE_SHOT (1<<3) + +struct gs_device_mode { + u32 mode; + u32 flags; +} __packed; + +struct gs_device_state { + u32 state; + u32 rxerr; + u32 txerr; +} __packed; + +struct gs_device_bittiming { + u32 prop_seg; + u32 phase_seg1; + u32 phase_seg2; + u32 sjw; + u32 brp; +} __packed; + +#define GS_CAN_FEATURE_LISTEN_ONLY (1<<0) +#define GS_CAN_FEATURE_LOOP_BACK (1<<1) +#define GS_CAN_FEATURE_TRIPLE_SAMPLE (1<<2) +#define GS_CAN_FEATURE_ONE_SHOT (1<<3) + +struct gs_device_bt_const { + u32 feature; + u32 fclk_can; + u32 tseg1_min; + u32 tseg1_max; + u32 tseg2_min; + u32 tseg2_max; + u32 sjw_max; + u32 brp_min; + u32 brp_max; + u32 brp_inc; +} __packed; + +#define GS_CAN_FLAG_OVERFLOW 1 + +struct gs_host_frame { + u32 echo_id; + u32 can_id; + + u8 can_dlc; + u8 channel; + u8 flags; + u8 reserved; + + u8 data[8]; +} __packed; +/* The GS USB devices make use of the same flags and masks as in + * linux/can.h and linux/can/error.h, and no additional mapping is necessary. + */ + +/* Only send a max of GS_MAX_TX_URBS frames per channel at a time. */ +#define GS_MAX_TX_URBS 10 +/* Only launch a max of GS_MAX_RX_URBS usb requests at a time. */ +#define GS_MAX_RX_URBS 30 +/* Maximum number of interfaces the driver supports per device. + * Current hardware only supports 2 interfaces. The future may vary. + */ +#define GS_MAX_INTF 2 + +struct gs_tx_context { + struct gs_can *dev; + unsigned int echo_id; +}; + +struct gs_can { + struct can_priv can; /* must be the first member */ + + struct gs_usb *parent; + + struct net_device *netdev; + struct usb_device *udev; + struct usb_interface *iface; + + struct can_bittiming_const bt_const; + unsigned int channel; /* channel number */ + + /* This lock prevents a race condition between xmit and recieve. */ + spinlock_t tx_ctx_lock; + struct gs_tx_context tx_context[GS_MAX_TX_URBS]; + + struct usb_anchor tx_submitted; + atomic_t active_tx_urbs; +}; + +/* usb interface struct */ +struct gs_usb { + struct gs_can *canch[GS_MAX_INTF]; + struct usb_anchor rx_submitted; + atomic_t active_channels; + struct usb_device *udev; +}; + +/* 'allocate' a tx context. + * returns a valid tx context or NULL if there is no space. + */ +static struct gs_tx_context *gs_alloc_tx_context(struct gs_can *dev) +{ + int i = 0; + unsigned long flags; + + spin_lock_irqsave(&dev->tx_ctx_lock, flags); + + for (; i < GS_MAX_TX_URBS; i++) { + if (dev->tx_context[i].echo_id == GS_MAX_TX_URBS) { + dev->tx_context[i].echo_id = i; + spin_unlock_irqrestore(&dev->tx_ctx_lock, flags); + return &dev->tx_context[i]; + } + } + + spin_unlock_irqrestore(&dev->tx_ctx_lock, flags); + return NULL; +} + +/* releases a tx context + */ +static void gs_free_tx_context(struct gs_tx_context *txc) +{ + txc->echo_id = GS_MAX_TX_URBS; +} + +/* Get a tx context by id. + */ +static struct gs_tx_context *gs_get_tx_context(struct gs_can *dev, unsigned int id) +{ + unsigned long flags; + + if (id < GS_MAX_TX_URBS) { + spin_lock_irqsave(&dev->tx_ctx_lock, flags); + if (dev->tx_context[id].echo_id == id) { + spin_unlock_irqrestore(&dev->tx_ctx_lock, flags); + return &dev->tx_context[id]; + } + spin_unlock_irqrestore(&dev->tx_ctx_lock, flags); + } + return NULL; +} + +static int gs_cmd_reset(struct gs_usb *gsusb, struct gs_can *gsdev) +{ + struct gs_device_mode *dm; + struct usb_interface *intf = gsdev->iface; + int rc; + + dm = kzalloc(sizeof(*dm), GFP_KERNEL); + if (!dm) + return -ENOMEM; + + dm->mode = GS_CAN_MODE_RESET; + + rc = usb_control_msg(interface_to_usbdev(intf), + usb_sndctrlpipe(interface_to_usbdev(intf), 0), + GS_USB_BREQ_MODE, + USB_DIR_OUT|USB_TYPE_VENDOR|USB_RECIP_INTERFACE, + gsdev->channel, + 0, + dm, + sizeof(*dm), + 1000); + + return rc; +} + +static void gs_update_state(struct gs_can *dev, struct can_frame *cf) +{ + struct can_device_stats *can_stats = &dev->can.can_stats; + + if (cf->can_id & CAN_ERR_RESTARTED) { + dev->can.state = CAN_STATE_ERROR_ACTIVE; + can_stats->restarts++; + } else if (cf->can_id & CAN_ERR_BUSOFF) { + dev->can.state = CAN_STATE_BUS_OFF; + can_stats->bus_off++; + } else if (cf->can_id & CAN_ERR_CRTL) { + if ((cf->data[1] & CAN_ERR_CRTL_TX_WARNING) || + (cf->data[1] & CAN_ERR_CRTL_RX_WARNING)) { + dev->can.state = CAN_STATE_ERROR_WARNING; + can_stats->error_warning++; + } else if ((cf->data[1] & CAN_ERR_CRTL_TX_PASSIVE) || + (cf->data[1] & CAN_ERR_CRTL_RX_PASSIVE)) { + dev->can.state = CAN_STATE_ERROR_PASSIVE; + can_stats->error_passive++; + } else { + dev->can.state = CAN_STATE_ERROR_ACTIVE; + } + } +} + +static void gs_usb_recieve_bulk_callback(struct urb *urb) +{ + struct gs_usb *usbcan = urb->context; + struct gs_can *dev; + struct net_device *netdev; + int rc; + struct net_device_stats *stats; + struct gs_host_frame *hf = urb->transfer_buffer; + struct gs_tx_context *txc; + struct can_frame *cf; + struct sk_buff *skb; + + BUG_ON(!usbcan); + + switch (urb->status) { + case 0: /* success */ + break; + case -ENOENT: + case -ESHUTDOWN: + return; + default: + /* do not resubmit aborted urbs. eg: when device goes down */ + return; + } + + /* device reports out of range channel id */ + if (hf->channel >= GS_MAX_INTF) + goto resubmit_urb; + + dev = usbcan->canch[hf->channel]; + + netdev = dev->netdev; + stats = &netdev->stats; + + if (!netif_device_present(netdev)) + return; + + if (hf->echo_id == -1) { /* normal rx */ + skb = alloc_can_skb(dev->netdev, &cf); + if (!skb) + return; + + cf->can_id = hf->can_id; + + cf->can_dlc = get_can_dlc(hf->can_dlc); + memcpy(cf->data, hf->data, 8); + + /* ERROR frames tell us information about the controller */ + if (hf->can_id & CAN_ERR_FLAG) + gs_update_state(dev, cf); + + netdev->stats.rx_packets++; + netdev->stats.rx_bytes += hf->can_dlc; + + netif_rx(skb); + } else { /* echo_id == hf->echo_id */ + if (hf->echo_id >= GS_MAX_TX_URBS) { + netdev_err(netdev, + "Unexpected out of range echo id %d\n", + hf->echo_id); + goto resubmit_urb; + } + + netdev->stats.tx_packets++; + netdev->stats.tx_bytes += hf->can_dlc; + + txc = gs_get_tx_context(dev, hf->echo_id); + + /* bad devices send bad echo_ids. */ + if (!txc) { + netdev_err(netdev, + "Unexpected unused echo id %d\n", + hf->echo_id); + goto resubmit_urb; + } + + can_get_echo_skb(netdev, hf->echo_id); + + gs_free_tx_context(txc); + + netif_wake_queue(netdev); + } + + if (hf->flags & GS_CAN_FLAG_OVERFLOW) { + skb = alloc_can_err_skb(netdev, &cf); + if (!skb) + goto resubmit_urb; + + cf->can_id |= CAN_ERR_CRTL; + cf->can_dlc = CAN_ERR_DLC; + cf->data[1] = CAN_ERR_CRTL_RX_OVERFLOW; + stats->rx_over_errors++; + stats->rx_errors++; + netif_rx(skb); + } + + resubmit_urb: + usb_fill_bulk_urb(urb, + usbcan->udev, + usb_rcvbulkpipe(usbcan->udev, GSUSB_ENDPOINT_IN), + hf, + sizeof(struct gs_host_frame), + gs_usb_recieve_bulk_callback, + usbcan + ); + + rc = usb_submit_urb(urb, GFP_ATOMIC); + + /* USB failure take down all interfaces */ + if (rc == -ENODEV) { + for (rc = 0; rc < GS_MAX_INTF; rc++) { + if (usbcan->canch[rc]) + netif_device_detach(usbcan->canch[rc]->netdev); + } + } +} + +static int gs_usb_set_bittiming(struct net_device *netdev) +{ + struct gs_can *dev = netdev_priv(netdev); + struct can_bittiming *bt = &dev->can.bittiming; + struct usb_interface *intf = dev->iface; + int rc; + struct gs_device_bittiming *dbt; + + dbt = kmalloc(sizeof(*dbt), GFP_KERNEL); + if (!dbt) + return -ENOMEM; + + dbt->prop_seg = bt->prop_seg; + dbt->phase_seg1 = bt->phase_seg1; + dbt->phase_seg2 = bt->phase_seg2; + dbt->sjw = bt->sjw; + dbt->brp = bt->brp; + + /* request bit timings */ + rc = usb_control_msg(interface_to_usbdev(intf), + usb_sndctrlpipe(interface_to_usbdev(intf), 0), + GS_USB_BREQ_BITTIMING, + USB_DIR_OUT|USB_TYPE_VENDOR|USB_RECIP_INTERFACE, + dev->channel, + 0, + dbt, + sizeof(*dbt), + 1000); + + kfree(dbt); + + if (rc < 0) + dev_err(netdev->dev.parent, "Couldn't set bittimings (err=%d)", + rc); + + return rc; +} + +static void gs_usb_xmit_callback(struct urb *urb) +{ + struct gs_tx_context *txc = urb->context; + struct gs_can *dev = txc->dev; + struct net_device *netdev = dev->netdev; + + if (urb->status) + netdev_info(netdev, "usb xmit fail %d\n", txc->echo_id); + + usb_free_coherent(urb->dev, + urb->transfer_buffer_length, + urb->transfer_buffer, + urb->transfer_dma); + + atomic_dec(&dev->active_tx_urbs); + + if (!netif_device_present(netdev)) + return; + + if (netif_queue_stopped(netdev)) + netif_wake_queue(netdev); +} + +static netdev_tx_t gs_can_start_xmit(struct sk_buff *skb, struct net_device *netdev) +{ + struct gs_can *dev = netdev_priv(netdev); + struct net_device_stats *stats = &dev->netdev->stats; + struct urb *urb; + struct gs_host_frame *hf; + struct can_frame *cf; + int rc; + unsigned int idx; + struct gs_tx_context *txc; + + if (can_dropped_invalid_skb(netdev, skb)) + return NETDEV_TX_OK; + + /* find an empty context to keep track of transmission */ + txc = gs_alloc_tx_context(dev); + if (!txc) + return NETDEV_TX_BUSY; + + /* create a URB, and a buffer for it */ + urb = usb_alloc_urb(0, GFP_ATOMIC); + if (!urb) { + netdev_err(netdev, "No memory left for URB\n"); + goto nomem_urb; + } + + hf = usb_alloc_coherent(dev->udev, sizeof(*hf), GFP_ATOMIC, + &urb->transfer_dma); + if (!hf) { + netdev_err(netdev, "No memory left for USB buffer\n"); + goto nomem_hf; + } + + idx = txc->echo_id; + + if (idx >= GS_MAX_TX_URBS) { + netdev_err(netdev, "Invalid tx context %d\n", idx); + goto badidx; + } + + hf->echo_id = idx; + hf->channel = dev->channel; + + cf = (struct can_frame *)skb->data; + + hf->can_id = cf->can_id; + hf->can_dlc = cf->can_dlc; + memcpy(hf->data, cf->data, cf->can_dlc); + + usb_fill_bulk_urb(urb, dev->udev, + usb_sndbulkpipe(dev->udev, GSUSB_ENDPOINT_OUT), + hf, + sizeof(*hf), + gs_usb_xmit_callback, + txc); + + urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP; + usb_anchor_urb(urb, &dev->tx_submitted); + + can_put_echo_skb(skb, netdev, idx); + + atomic_inc(&dev->active_tx_urbs); + + rc = usb_submit_urb(urb, GFP_ATOMIC); + if (unlikely(rc)) { /* usb send failed */ + atomic_dec(&dev->active_tx_urbs); + + can_free_echo_skb(netdev, idx); + gs_free_tx_context(txc); + + usb_unanchor_urb(urb); + usb_free_coherent(dev->udev, + sizeof(*hf), + hf, + urb->transfer_dma); + + + if (rc == -ENODEV) { + netif_device_detach(netdev); + } else { + netdev_err(netdev, "usb_submit failed (err=%d)\n", rc); + stats->tx_dropped++; + } + } else { + /* Slow down tx path */ + if (atomic_read(&dev->active_tx_urbs) >= GS_MAX_TX_URBS) + netif_stop_queue(netdev); + } + + /* let usb core take care of this urb */ + usb_free_urb(urb); + + return NETDEV_TX_OK; + + badidx: + usb_free_coherent(dev->udev, + sizeof(*hf), + hf, + urb->transfer_dma); + nomem_hf: + usb_free_urb(urb); + + nomem_urb: + gs_free_tx_context(txc); + dev_kfree_skb(skb); + stats->tx_dropped++; + return NETDEV_TX_OK; +} + +static int gs_can_open(struct net_device *netdev) +{ + struct gs_can *dev = netdev_priv(netdev); + struct gs_usb *parent = dev->parent; + int rc, i; + struct gs_device_mode *dm; + u32 ctrlmode; + + rc = open_candev(netdev); + if (rc) + return rc; + + if (atomic_add_return(1, &parent->active_channels) == 1) { + for (i = 0; i < GS_MAX_RX_URBS; i++) { + struct urb *urb; + u8 *buf; + + /* alloc rx urb */ + urb = usb_alloc_urb(0, GFP_KERNEL); + if (!urb) { + netdev_err(netdev, + "No memory left for URB\n"); + return -ENOMEM; + } + + /* alloc rx buffer */ + buf = usb_alloc_coherent(dev->udev, + sizeof(struct gs_host_frame), + GFP_KERNEL, + &urb->transfer_dma); + if (!buf) { + netdev_err(netdev, + "No memory left for USB buffer\n"); + usb_free_urb(urb); + return -ENOMEM; + } + + /* fill, anchor, and submit rx urb */ + usb_fill_bulk_urb(urb, + dev->udev, + usb_rcvbulkpipe(dev->udev, + GSUSB_ENDPOINT_IN), + buf, + sizeof(struct gs_host_frame), + gs_usb_recieve_bulk_callback, + parent); + urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP; + + usb_anchor_urb(urb, &parent->rx_submitted); + + rc = usb_submit_urb(urb, GFP_KERNEL); + if (rc) { + if (rc == -ENODEV) + netif_device_detach(dev->netdev); + + netdev_err(netdev, + "usb_submit failed (err=%d)\n", + rc); + + usb_unanchor_urb(urb); + break; + } + + /* Drop reference, + * USB core will take care of freeing it + */ + usb_free_urb(urb); + } + } + + dm = kmalloc(sizeof(*dm), GFP_KERNEL); + if (!dm) + return -ENOMEM; + + /* flags */ + ctrlmode = dev->can.ctrlmode; + dm->flags = 0; + + if (ctrlmode & CAN_CTRLMODE_LOOPBACK) + dm->flags |= GS_CAN_MODE_LOOP_BACK; + else if (ctrlmode & CAN_CTRLMODE_LISTENONLY) + dm->flags |= GS_CAN_MODE_LISTEN_ONLY; + + /* Controller is not allowed to retry TX + * this mode is unavailable on atmels uc3c hardware + */ + if (ctrlmode & CAN_CTRLMODE_ONE_SHOT) + dm->flags |= GS_CAN_MODE_ONE_SHOT; + + if (ctrlmode & CAN_CTRLMODE_3_SAMPLES) + dm->flags |= GS_CAN_MODE_TRIPLE_SAMPLE; + + /* finally start device */ + dm->mode = GS_CAN_MODE_START; + rc = usb_control_msg(interface_to_usbdev(dev->iface), + usb_sndctrlpipe(interface_to_usbdev(dev->iface), 0), + GS_USB_BREQ_MODE, + USB_DIR_OUT|USB_TYPE_VENDOR|USB_RECIP_INTERFACE, + dev->channel, + 0, + dm, + sizeof(*dm), + 1000); + + if (rc < 0) { + netdev_err(netdev, "Couldn't start device (err=%d)\n", rc); + kfree(dm); + return rc; + } + + kfree(dm); + + dev->can.state = CAN_STATE_ERROR_ACTIVE; + + if (!(dev->can.ctrlmode & CAN_CTRLMODE_LISTENONLY)) + netif_start_queue(netdev); + + return 0; +} + +static int gs_can_close(struct net_device *netdev) +{ + int rc; + struct gs_can *dev = netdev_priv(netdev); + struct gs_usb *parent = dev->parent; + + netif_stop_queue(netdev); + + /* Stop polling */ + if (atomic_dec_and_test(&parent->active_channels)) + usb_kill_anchored_urbs(&parent->rx_submitted); + + /* Stop sending URBs */ + usb_kill_anchored_urbs(&dev->tx_submitted); + atomic_set(&dev->active_tx_urbs, 0); + + /* reset the device */ + rc = gs_cmd_reset(parent, dev); + if (rc < 0) + netdev_warn(netdev, "Couldn't shutdown device (err=%d)", rc); + + /* reset tx contexts */ + for (rc = 0; rc < GS_MAX_TX_URBS; rc++) { + dev->tx_context[rc].dev = dev; + dev->tx_context[rc].echo_id = GS_MAX_TX_URBS; + } + + /* close the netdev */ + close_candev(netdev); + + return 0; +} + +static const struct net_device_ops gs_usb_netdev_ops = { + .ndo_open = gs_can_open, + .ndo_stop = gs_can_close, + .ndo_start_xmit = gs_can_start_xmit, +}; + +static struct gs_can *gs_make_candev(unsigned int channel, struct usb_interface *intf) +{ + struct gs_can *dev; + struct net_device *netdev; + int rc; + struct gs_device_bt_const *bt_const; + + bt_const = kmalloc(sizeof(*bt_const), GFP_KERNEL); + if (!bt_const) + return ERR_PTR(-ENOMEM); + + /* fetch bit timing constants */ + rc = usb_control_msg(interface_to_usbdev(intf), + usb_rcvctrlpipe(interface_to_usbdev(intf), 0), + GS_USB_BREQ_BT_CONST, + USB_DIR_IN|USB_TYPE_VENDOR|USB_RECIP_INTERFACE, + channel, + 0, + bt_const, + sizeof(*bt_const), + 1000); + + if (rc < 0) { + dev_err(&intf->dev, + "Couldn't get bit timing const for channel (err=%d)\n", + rc); + kfree(bt_const); + return ERR_PTR(rc); + } + + /* create netdev */ + netdev = alloc_candev(sizeof(struct gs_can), GS_MAX_TX_URBS); + if (!netdev) { + dev_err(&intf->dev, "Couldn't allocate candev\n"); + kfree(bt_const); + return ERR_PTR(-ENOMEM); + } + + dev = netdev_priv(netdev); + + netdev->netdev_ops = &gs_usb_netdev_ops; + + netdev->flags |= IFF_ECHO; /* we support full roundtrip echo */ + + /* dev settup */ + strcpy(dev->bt_const.name, "gs_usb"); + dev->bt_const.tseg1_min = bt_const->tseg1_min; + dev->bt_const.tseg1_max = bt_const->tseg1_max; + dev->bt_const.tseg2_min = bt_const->tseg2_min; + dev->bt_const.tseg2_max = bt_const->tseg2_max; + dev->bt_const.sjw_max = bt_const->sjw_max; + dev->bt_const.brp_min = bt_const->brp_min; + dev->bt_const.brp_max = bt_const->brp_max; + dev->bt_const.brp_inc = bt_const->brp_inc; + + dev->udev = interface_to_usbdev(intf); + dev->iface = intf; + dev->netdev = netdev; + dev->channel = channel; + + init_usb_anchor(&dev->tx_submitted); + atomic_set(&dev->active_tx_urbs, 0); + spin_lock_init(&dev->tx_ctx_lock); + for (rc = 0; rc < GS_MAX_TX_URBS; rc++) { + dev->tx_context[rc].dev = dev; + dev->tx_context[rc].echo_id = GS_MAX_TX_URBS; + } + + /* can settup */ + dev->can.state = CAN_STATE_STOPPED; + dev->can.clock.freq = bt_const->fclk_can; + dev->can.bittiming_const = &dev->bt_const; + dev->can.do_set_bittiming = gs_usb_set_bittiming; + + dev->can.ctrlmode_supported = 0; + + if (bt_const->feature & GS_CAN_FEATURE_LISTEN_ONLY) + dev->can.ctrlmode_supported |= CAN_CTRLMODE_LISTENONLY; + + if (bt_const->feature & GS_CAN_FEATURE_LOOP_BACK) + dev->can.ctrlmode_supported |= CAN_CTRLMODE_LOOPBACK; + + if (bt_const->feature & GS_CAN_FEATURE_TRIPLE_SAMPLE) + dev->can.ctrlmode_supported |= CAN_CTRLMODE_3_SAMPLES; + + if (bt_const->feature & GS_CAN_FEATURE_ONE_SHOT) + dev->can.ctrlmode_supported |= CAN_CTRLMODE_ONE_SHOT; + + kfree(bt_const); + + SET_NETDEV_DEV(netdev, &intf->dev); + + rc = register_candev(dev->netdev); + if (rc) { + free_candev(dev->netdev); + dev_err(&intf->dev, "Couldn't register candev (err=%d)\n", rc); + return ERR_PTR(rc); + } + + return dev; +} + +static void gs_destroy_candev(struct gs_can *dev) +{ + unregister_candev(dev->netdev); + free_candev(dev->netdev); + usb_kill_anchored_urbs(&dev->tx_submitted); + kfree(dev); +} + +static int gs_usb_probe(struct usb_interface *intf, const struct usb_device_id *id) +{ + struct gs_usb *dev; + int rc = -ENOMEM; + unsigned int icount, i; + struct gs_host_config *hconf; + struct gs_device_config *dconf; + + hconf = kmalloc(sizeof(*hconf), GFP_KERNEL); + if (!hconf) + return -ENOMEM; + + hconf->byte_order = 0x0000beef; + + /* send host config */ + rc = usb_control_msg(interface_to_usbdev(intf), + usb_sndctrlpipe(interface_to_usbdev(intf), 0), + GS_USB_BREQ_HOST_FORMAT, + USB_DIR_OUT|USB_TYPE_VENDOR|USB_RECIP_INTERFACE, + 1, + intf->altsetting[0].desc.bInterfaceNumber, + hconf, + sizeof(*hconf), + 1000); + + kfree(hconf); + + if (rc < 0) { + dev_err(&intf->dev, "Couldn't send data format (err=%d)\n", + rc); + return rc; + } + + dconf = kmalloc(sizeof(*dconf), GFP_KERNEL); + if (!dconf) + return -ENOMEM; + + /* read device config */ + rc = usb_control_msg(interface_to_usbdev(intf), + usb_rcvctrlpipe(interface_to_usbdev(intf), 0), + GS_USB_BREQ_DEVICE_CONFIG, + USB_DIR_IN|USB_TYPE_VENDOR|USB_RECIP_INTERFACE, + 1, + intf->altsetting[0].desc.bInterfaceNumber, + dconf, + sizeof(*dconf), + 1000); + if (rc < 0) { + dev_err(&intf->dev, "Couldn't get device config: (err=%d)\n", + rc); + + kfree(dconf); + + return rc; + } + + icount = dconf->icount+1; + + kfree(dconf); + + dev_info(&intf->dev, "Configuring for %d interfaces\n", icount); + + if (icount > GS_MAX_INTF) { + dev_err(&intf->dev, + "Driver cannot handle more that %d CAN interfaces\n", + GS_MAX_INTF); + return -EINVAL; + } + + dev = kzalloc(sizeof(*dev), GFP_KERNEL); + init_usb_anchor(&dev->rx_submitted); + + atomic_set(&dev->active_channels, 0); + + usb_set_intfdata(intf, dev); + dev->udev = interface_to_usbdev(intf); + + for (i = 0; i < icount; i++) { + dev->canch[i] = gs_make_candev(i, intf); + if (IS_ERR_OR_NULL(dev->canch[i])) { + /* on failure destroy previously created candevs */ + icount = i; + for (i = 0; i < icount; i++) { + gs_destroy_candev(dev->canch[i]); + dev->canch[i] = NULL; + } + kfree(dev); + return rc; + } + dev->canch[i]->parent = dev; + } + + return 0; +} + +static void gs_usb_disconnect(struct usb_interface *intf) +{ + unsigned i; + struct gs_usb *dev = usb_get_intfdata(intf); + usb_set_intfdata(intf, NULL); + + if (!dev) { + dev_err(&intf->dev, "Disconnect (nodata)\n"); + return; + } + + for (i = 0; i < GS_MAX_INTF; i++) { + struct gs_can *can = dev->canch[i]; + + if (!can) + continue; + + gs_destroy_candev(can); + } + + usb_kill_anchored_urbs(&dev->rx_submitted); +} + +static const struct usb_device_id gs_usb_table[] = { + {USB_DEVICE(USB_GSUSB_1_VENDOR_ID, USB_GSUSB_1_PRODUCT_ID)}, + {} /* Terminating entry */ +}; + +MODULE_DEVICE_TABLE(usb, gs_usb_table); + +static struct usb_driver gs_usb_driver = { + .name = "gs_usb", + .probe = gs_usb_probe, + .disconnect = gs_usb_disconnect, + .id_table = gs_usb_table, +}; + +module_usb_driver(gs_usb_driver); + +MODULE_AUTHOR("Maximilian Schneider <mws@schneidersoft.net>"); +MODULE_DESCRIPTION( +"Socket CAN device driver for Geschwister Schneider Technologie-, " +"Entwicklungs- und Vertriebs UG. USB2.0 to CAN interfaces."); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/net/can/usb/kvaser_usb.c b/drivers/net/can/usb/kvaser_usb.c index 3b954658824..541fb7a0562 100644 --- a/drivers/net/can/usb/kvaser_usb.c +++ b/drivers/net/can/usb/kvaser_usb.c @@ -12,7 +12,6 @@ * Copyright (C) 2012 Olivier Sobrie <olivier@sobrie.be> */ -#include <linux/init.h> #include <linux/completion.h> #include <linux/module.h> #include <linux/netdevice.h> @@ -54,6 +53,8 @@ #define USB_OEM_MERCURY_PRODUCT_ID 34 #define USB_OEM_LEAF_PRODUCT_ID 35 #define USB_CAN_R_PRODUCT_ID 39 +#define USB_LEAF_LITE_V2_PRODUCT_ID 288 +#define USB_MINI_PCIE_HS_PRODUCT_ID 289 /* USB devices features */ #define KVASER_HAS_SILENT_MODE BIT(0) @@ -357,6 +358,8 @@ static const struct usb_device_id kvaser_usb_table[] = { .driver_info = KVASER_HAS_TXRX_ERRORS }, { USB_DEVICE(KVASER_VENDOR_ID, USB_CAN_R_PRODUCT_ID), .driver_info = KVASER_HAS_TXRX_ERRORS }, + { USB_DEVICE(KVASER_VENDOR_ID, USB_LEAF_LITE_V2_PRODUCT_ID) }, + { USB_DEVICE(KVASER_VENDOR_ID, USB_MINI_PCIE_HS_PRODUCT_ID) }, { } }; MODULE_DEVICE_TABLE(usb, kvaser_usb_table); @@ -380,38 +383,43 @@ static int kvaser_usb_wait_msg(const struct kvaser_usb *dev, u8 id, void *buf; int actual_len; int err; - int pos = 0; + int pos; + unsigned long to = jiffies + msecs_to_jiffies(USB_RECV_TIMEOUT); buf = kzalloc(RX_BUFFER_SIZE, GFP_KERNEL); if (!buf) return -ENOMEM; - err = usb_bulk_msg(dev->udev, - usb_rcvbulkpipe(dev->udev, - dev->bulk_in->bEndpointAddress), - buf, RX_BUFFER_SIZE, &actual_len, - USB_RECV_TIMEOUT); - if (err < 0) - goto end; + do { + err = usb_bulk_msg(dev->udev, + usb_rcvbulkpipe(dev->udev, + dev->bulk_in->bEndpointAddress), + buf, RX_BUFFER_SIZE, &actual_len, + USB_RECV_TIMEOUT); + if (err < 0) + goto end; - while (pos <= actual_len - MSG_HEADER_LEN) { - tmp = buf + pos; + pos = 0; + while (pos <= actual_len - MSG_HEADER_LEN) { + tmp = buf + pos; - if (!tmp->len) - break; + if (!tmp->len) + break; - if (pos + tmp->len > actual_len) { - dev_err(dev->udev->dev.parent, "Format error\n"); - break; - } + if (pos + tmp->len > actual_len) { + dev_err(dev->udev->dev.parent, + "Format error\n"); + break; + } - if (tmp->id == id) { - memcpy(msg, tmp, tmp->len); - goto end; - } + if (tmp->id == id) { + memcpy(msg, tmp, tmp->len); + goto end; + } - pos += tmp->len; - } + pos += tmp->len; + } + } while (time_before(jiffies, to)); err = -EINVAL; @@ -474,6 +482,8 @@ static int kvaser_usb_get_card_info(struct kvaser_usb *dev) return err; dev->nchannels = msg.u.cardinfo.nchannels; + if (dev->nchannels > MAX_NET_DEVICES) + return -EINVAL; return 0; } @@ -1387,6 +1397,7 @@ static const struct net_device_ops kvaser_usb_netdev_ops = { .ndo_open = kvaser_usb_open, .ndo_stop = kvaser_usb_close, .ndo_start_xmit = kvaser_usb_start_xmit, + .ndo_change_mtu = can_change_mtu, }; static const struct can_bittiming_const kvaser_usb_bittiming_const = { @@ -1528,6 +1539,7 @@ static int kvaser_usb_init_one(struct usb_interface *intf, netdev->netdev_ops = &kvaser_usb_netdev_ops; SET_NETDEV_DEV(netdev, &intf->dev); + netdev->dev_id = channel; dev->nets[channel] = priv; @@ -1544,9 +1556,9 @@ static int kvaser_usb_init_one(struct usb_interface *intf, return 0; } -static void kvaser_usb_get_endpoints(const struct usb_interface *intf, - struct usb_endpoint_descriptor **in, - struct usb_endpoint_descriptor **out) +static int kvaser_usb_get_endpoints(const struct usb_interface *intf, + struct usb_endpoint_descriptor **in, + struct usb_endpoint_descriptor **out) { const struct usb_host_interface *iface_desc; struct usb_endpoint_descriptor *endpoint; @@ -1557,12 +1569,18 @@ static void kvaser_usb_get_endpoints(const struct usb_interface *intf, for (i = 0; i < iface_desc->desc.bNumEndpoints; ++i) { endpoint = &iface_desc->endpoint[i].desc; - if (usb_endpoint_is_bulk_in(endpoint)) + if (!*in && usb_endpoint_is_bulk_in(endpoint)) *in = endpoint; - if (usb_endpoint_is_bulk_out(endpoint)) + if (!*out && usb_endpoint_is_bulk_out(endpoint)) *out = endpoint; + + /* use first bulk endpoint for in and out */ + if (*in && *out) + return 0; } + + return -ENODEV; } static int kvaser_usb_probe(struct usb_interface *intf, @@ -1576,8 +1594,8 @@ static int kvaser_usb_probe(struct usb_interface *intf, if (!dev) return -ENOMEM; - kvaser_usb_get_endpoints(intf, &dev->bulk_in, &dev->bulk_out); - if (!dev->bulk_in || !dev->bulk_out) { + err = kvaser_usb_get_endpoints(intf, &dev->bulk_in, &dev->bulk_out); + if (err) { dev_err(&intf->dev, "Cannot get usb endpoint(s)"); return err; } diff --git a/drivers/net/can/usb/peak_usb/pcan_usb_core.c b/drivers/net/can/usb/peak_usb/pcan_usb_core.c index 0b7a4c3b01a..644e6ab8a48 100644 --- a/drivers/net/can/usb/peak_usb/pcan_usb_core.c +++ b/drivers/net/can/usb/peak_usb/pcan_usb_core.c @@ -702,6 +702,7 @@ static const struct net_device_ops peak_usb_netdev_ops = { .ndo_open = peak_usb_ndo_open, .ndo_stop = peak_usb_ndo_stop, .ndo_start_xmit = peak_usb_ndo_start_xmit, + .ndo_change_mtu = can_change_mtu, }; /* @@ -769,6 +770,7 @@ static int peak_usb_create_dev(struct peak_usb_adapter *peak_usb_adapter, usb_set_intfdata(intf, dev); SET_NETDEV_DEV(netdev, &intf->dev); + netdev->dev_id = ctrl_idx; err = register_candev(netdev); if (err) { diff --git a/drivers/net/can/usb/peak_usb/pcan_usb_pro.c b/drivers/net/can/usb/peak_usb/pcan_usb_pro.c index 8ee9d1556e6..263dd921edc 100644 --- a/drivers/net/can/usb/peak_usb/pcan_usb_pro.c +++ b/drivers/net/can/usb/peak_usb/pcan_usb_pro.c @@ -927,6 +927,9 @@ static int pcan_usb_pro_init(struct peak_usb_device *dev) /* set LED in default state (end of init phase) */ pcan_usb_pro_set_led(dev, 0, 1); + kfree(bi); + kfree(fi); + return 0; err_out: diff --git a/drivers/net/can/usb/usb_8dev.c b/drivers/net/can/usb/usb_8dev.c index 8becd3d838b..ef674ecb82f 100644 --- a/drivers/net/can/usb/usb_8dev.c +++ b/drivers/net/can/usb/usb_8dev.c @@ -23,7 +23,6 @@ * who were very cooperative and answered my questions. */ -#include <linux/init.h> #include <linux/signal.h> #include <linux/slab.h> #include <linux/module.h> @@ -698,8 +697,8 @@ static netdev_tx_t usb_8dev_start_xmit(struct sk_buff *skb, return NETDEV_TX_OK; nofreecontext: - usb_unanchor_urb(urb); usb_free_coherent(priv->udev, size, buf, urb->transfer_dma); + usb_free_urb(urb); netdev_warn(netdev, "couldn't find free context"); @@ -888,6 +887,7 @@ static const struct net_device_ops usb_8dev_netdev_ops = { .ndo_open = usb_8dev_open, .ndo_stop = usb_8dev_close, .ndo_start_xmit = usb_8dev_start_xmit, + .ndo_change_mtu = can_change_mtu, }; static const struct can_bittiming_const usb_8dev_bittiming_const = { diff --git a/drivers/net/can/vcan.c b/drivers/net/can/vcan.c index 0a2a5ee79a1..4e94057ef5c 100644 --- a/drivers/net/can/vcan.c +++ b/drivers/net/can/vcan.c @@ -46,6 +46,7 @@ #include <linux/if_ether.h> #include <linux/can.h> #include <linux/can/dev.h> +#include <linux/can/skb.h> #include <linux/slab.h> #include <net/rtnetlink.h> @@ -109,25 +110,23 @@ static netdev_tx_t vcan_tx(struct sk_buff *skb, struct net_device *dev) stats->rx_packets++; stats->rx_bytes += cfd->len; } - kfree_skb(skb); + consume_skb(skb); return NETDEV_TX_OK; } /* perform standard echo handling for CAN network interfaces */ if (loop) { - struct sock *srcsk = skb->sk; - skb = skb_share_check(skb, GFP_ATOMIC); + skb = can_create_echo_skb(skb); if (!skb) return NETDEV_TX_OK; /* receive with packet counting */ - skb->sk = srcsk; vcan_rx(skb, dev); } else { /* no looped packets => no counting */ - kfree_skb(skb); + consume_skb(skb); } return NETDEV_TX_OK; } diff --git a/drivers/net/can/xilinx_can.c b/drivers/net/can/xilinx_can.c new file mode 100644 index 00000000000..5e8b5609c06 --- /dev/null +++ b/drivers/net/can/xilinx_can.c @@ -0,0 +1,1208 @@ +/* Xilinx CAN device driver + * + * Copyright (C) 2012 - 2014 Xilinx, Inc. + * Copyright (C) 2009 PetaLogix. All rights reserved. + * + * Description: + * This driver is developed for Axi CAN IP and for Zynq CANPS Controller. + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <linux/clk.h> +#include <linux/errno.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/io.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/netdevice.h> +#include <linux/of.h> +#include <linux/platform_device.h> +#include <linux/skbuff.h> +#include <linux/string.h> +#include <linux/types.h> +#include <linux/can/dev.h> +#include <linux/can/error.h> +#include <linux/can/led.h> + +#define DRIVER_NAME "xilinx_can" + +/* CAN registers set */ +enum xcan_reg { + XCAN_SRR_OFFSET = 0x00, /* Software reset */ + XCAN_MSR_OFFSET = 0x04, /* Mode select */ + XCAN_BRPR_OFFSET = 0x08, /* Baud rate prescaler */ + XCAN_BTR_OFFSET = 0x0C, /* Bit timing */ + XCAN_ECR_OFFSET = 0x10, /* Error counter */ + XCAN_ESR_OFFSET = 0x14, /* Error status */ + XCAN_SR_OFFSET = 0x18, /* Status */ + XCAN_ISR_OFFSET = 0x1C, /* Interrupt status */ + XCAN_IER_OFFSET = 0x20, /* Interrupt enable */ + XCAN_ICR_OFFSET = 0x24, /* Interrupt clear */ + XCAN_TXFIFO_ID_OFFSET = 0x30,/* TX FIFO ID */ + XCAN_TXFIFO_DLC_OFFSET = 0x34, /* TX FIFO DLC */ + XCAN_TXFIFO_DW1_OFFSET = 0x38, /* TX FIFO Data Word 1 */ + XCAN_TXFIFO_DW2_OFFSET = 0x3C, /* TX FIFO Data Word 2 */ + XCAN_RXFIFO_ID_OFFSET = 0x50, /* RX FIFO ID */ + XCAN_RXFIFO_DLC_OFFSET = 0x54, /* RX FIFO DLC */ + XCAN_RXFIFO_DW1_OFFSET = 0x58, /* RX FIFO Data Word 1 */ + XCAN_RXFIFO_DW2_OFFSET = 0x5C, /* RX FIFO Data Word 2 */ +}; + +/* CAN register bit masks - XCAN_<REG>_<BIT>_MASK */ +#define XCAN_SRR_CEN_MASK 0x00000002 /* CAN enable */ +#define XCAN_SRR_RESET_MASK 0x00000001 /* Soft Reset the CAN core */ +#define XCAN_MSR_LBACK_MASK 0x00000002 /* Loop back mode select */ +#define XCAN_MSR_SLEEP_MASK 0x00000001 /* Sleep mode select */ +#define XCAN_BRPR_BRP_MASK 0x000000FF /* Baud rate prescaler */ +#define XCAN_BTR_SJW_MASK 0x00000180 /* Synchronous jump width */ +#define XCAN_BTR_TS2_MASK 0x00000070 /* Time segment 2 */ +#define XCAN_BTR_TS1_MASK 0x0000000F /* Time segment 1 */ +#define XCAN_ECR_REC_MASK 0x0000FF00 /* Receive error counter */ +#define XCAN_ECR_TEC_MASK 0x000000FF /* Transmit error counter */ +#define XCAN_ESR_ACKER_MASK 0x00000010 /* ACK error */ +#define XCAN_ESR_BERR_MASK 0x00000008 /* Bit error */ +#define XCAN_ESR_STER_MASK 0x00000004 /* Stuff error */ +#define XCAN_ESR_FMER_MASK 0x00000002 /* Form error */ +#define XCAN_ESR_CRCER_MASK 0x00000001 /* CRC error */ +#define XCAN_SR_TXFLL_MASK 0x00000400 /* TX FIFO is full */ +#define XCAN_SR_ESTAT_MASK 0x00000180 /* Error status */ +#define XCAN_SR_ERRWRN_MASK 0x00000040 /* Error warning */ +#define XCAN_SR_NORMAL_MASK 0x00000008 /* Normal mode */ +#define XCAN_SR_LBACK_MASK 0x00000002 /* Loop back mode */ +#define XCAN_SR_CONFIG_MASK 0x00000001 /* Configuration mode */ +#define XCAN_IXR_TXFEMP_MASK 0x00004000 /* TX FIFO Empty */ +#define XCAN_IXR_WKUP_MASK 0x00000800 /* Wake up interrupt */ +#define XCAN_IXR_SLP_MASK 0x00000400 /* Sleep interrupt */ +#define XCAN_IXR_BSOFF_MASK 0x00000200 /* Bus off interrupt */ +#define XCAN_IXR_ERROR_MASK 0x00000100 /* Error interrupt */ +#define XCAN_IXR_RXNEMP_MASK 0x00000080 /* RX FIFO NotEmpty intr */ +#define XCAN_IXR_RXOFLW_MASK 0x00000040 /* RX FIFO Overflow intr */ +#define XCAN_IXR_RXOK_MASK 0x00000010 /* Message received intr */ +#define XCAN_IXR_TXFLL_MASK 0x00000004 /* Tx FIFO Full intr */ +#define XCAN_IXR_TXOK_MASK 0x00000002 /* TX successful intr */ +#define XCAN_IXR_ARBLST_MASK 0x00000001 /* Arbitration lost intr */ +#define XCAN_IDR_ID1_MASK 0xFFE00000 /* Standard msg identifier */ +#define XCAN_IDR_SRR_MASK 0x00100000 /* Substitute remote TXreq */ +#define XCAN_IDR_IDE_MASK 0x00080000 /* Identifier extension */ +#define XCAN_IDR_ID2_MASK 0x0007FFFE /* Extended message ident */ +#define XCAN_IDR_RTR_MASK 0x00000001 /* Remote TX request */ +#define XCAN_DLCR_DLC_MASK 0xF0000000 /* Data length code */ + +#define XCAN_INTR_ALL (XCAN_IXR_TXOK_MASK | XCAN_IXR_BSOFF_MASK |\ + XCAN_IXR_WKUP_MASK | XCAN_IXR_SLP_MASK | \ + XCAN_IXR_RXNEMP_MASK | XCAN_IXR_ERROR_MASK | \ + XCAN_IXR_ARBLST_MASK | XCAN_IXR_RXOK_MASK) + +/* CAN register bit shift - XCAN_<REG>_<BIT>_SHIFT */ +#define XCAN_BTR_SJW_SHIFT 7 /* Synchronous jump width */ +#define XCAN_BTR_TS2_SHIFT 4 /* Time segment 2 */ +#define XCAN_IDR_ID1_SHIFT 21 /* Standard Messg Identifier */ +#define XCAN_IDR_ID2_SHIFT 1 /* Extended Message Identifier */ +#define XCAN_DLCR_DLC_SHIFT 28 /* Data length code */ +#define XCAN_ESR_REC_SHIFT 8 /* Rx Error Count */ + +/* CAN frame length constants */ +#define XCAN_FRAME_MAX_DATA_LEN 8 +#define XCAN_TIMEOUT (1 * HZ) + +/** + * struct xcan_priv - This definition define CAN driver instance + * @can: CAN private data structure. + * @tx_head: Tx CAN packets ready to send on the queue + * @tx_tail: Tx CAN packets successfully sended on the queue + * @tx_max: Maximum number packets the driver can send + * @napi: NAPI structure + * @read_reg: For reading data from CAN registers + * @write_reg: For writing data to CAN registers + * @dev: Network device data structure + * @reg_base: Ioremapped address to registers + * @irq_flags: For request_irq() + * @bus_clk: Pointer to struct clk + * @can_clk: Pointer to struct clk + */ +struct xcan_priv { + struct can_priv can; + unsigned int tx_head; + unsigned int tx_tail; + unsigned int tx_max; + struct napi_struct napi; + u32 (*read_reg)(const struct xcan_priv *priv, enum xcan_reg reg); + void (*write_reg)(const struct xcan_priv *priv, enum xcan_reg reg, + u32 val); + struct net_device *dev; + void __iomem *reg_base; + unsigned long irq_flags; + struct clk *bus_clk; + struct clk *can_clk; +}; + +/* CAN Bittiming constants as per Xilinx CAN specs */ +static const struct can_bittiming_const xcan_bittiming_const = { + .name = DRIVER_NAME, + .tseg1_min = 1, + .tseg1_max = 16, + .tseg2_min = 1, + .tseg2_max = 8, + .sjw_max = 4, + .brp_min = 1, + .brp_max = 256, + .brp_inc = 1, +}; + +/** + * xcan_write_reg_le - Write a value to the device register little endian + * @priv: Driver private data structure + * @reg: Register offset + * @val: Value to write at the Register offset + * + * Write data to the paricular CAN register + */ +static void xcan_write_reg_le(const struct xcan_priv *priv, enum xcan_reg reg, + u32 val) +{ + iowrite32(val, priv->reg_base + reg); +} + +/** + * xcan_read_reg_le - Read a value from the device register little endian + * @priv: Driver private data structure + * @reg: Register offset + * + * Read data from the particular CAN register + * Return: value read from the CAN register + */ +static u32 xcan_read_reg_le(const struct xcan_priv *priv, enum xcan_reg reg) +{ + return ioread32(priv->reg_base + reg); +} + +/** + * xcan_write_reg_be - Write a value to the device register big endian + * @priv: Driver private data structure + * @reg: Register offset + * @val: Value to write at the Register offset + * + * Write data to the paricular CAN register + */ +static void xcan_write_reg_be(const struct xcan_priv *priv, enum xcan_reg reg, + u32 val) +{ + iowrite32be(val, priv->reg_base + reg); +} + +/** + * xcan_read_reg_be - Read a value from the device register big endian + * @priv: Driver private data structure + * @reg: Register offset + * + * Read data from the particular CAN register + * Return: value read from the CAN register + */ +static u32 xcan_read_reg_be(const struct xcan_priv *priv, enum xcan_reg reg) +{ + return ioread32be(priv->reg_base + reg); +} + +/** + * set_reset_mode - Resets the CAN device mode + * @ndev: Pointer to net_device structure + * + * This is the driver reset mode routine.The driver + * enters into configuration mode. + * + * Return: 0 on success and failure value on error + */ +static int set_reset_mode(struct net_device *ndev) +{ + struct xcan_priv *priv = netdev_priv(ndev); + unsigned long timeout; + + priv->write_reg(priv, XCAN_SRR_OFFSET, XCAN_SRR_RESET_MASK); + + timeout = jiffies + XCAN_TIMEOUT; + while (!(priv->read_reg(priv, XCAN_SR_OFFSET) & XCAN_SR_CONFIG_MASK)) { + if (time_after(jiffies, timeout)) { + netdev_warn(ndev, "timed out for config mode\n"); + return -ETIMEDOUT; + } + usleep_range(500, 10000); + } + + return 0; +} + +/** + * xcan_set_bittiming - CAN set bit timing routine + * @ndev: Pointer to net_device structure + * + * This is the driver set bittiming routine. + * Return: 0 on success and failure value on error + */ +static int xcan_set_bittiming(struct net_device *ndev) +{ + struct xcan_priv *priv = netdev_priv(ndev); + struct can_bittiming *bt = &priv->can.bittiming; + u32 btr0, btr1; + u32 is_config_mode; + + /* Check whether Xilinx CAN is in configuration mode. + * It cannot set bit timing if Xilinx CAN is not in configuration mode. + */ + is_config_mode = priv->read_reg(priv, XCAN_SR_OFFSET) & + XCAN_SR_CONFIG_MASK; + if (!is_config_mode) { + netdev_alert(ndev, + "BUG! Cannot set bittiming - CAN is not in config mode\n"); + return -EPERM; + } + + /* Setting Baud Rate prescalar value in BRPR Register */ + btr0 = (bt->brp - 1); + + /* Setting Time Segment 1 in BTR Register */ + btr1 = (bt->prop_seg + bt->phase_seg1 - 1); + + /* Setting Time Segment 2 in BTR Register */ + btr1 |= (bt->phase_seg2 - 1) << XCAN_BTR_TS2_SHIFT; + + /* Setting Synchronous jump width in BTR Register */ + btr1 |= (bt->sjw - 1) << XCAN_BTR_SJW_SHIFT; + + priv->write_reg(priv, XCAN_BRPR_OFFSET, btr0); + priv->write_reg(priv, XCAN_BTR_OFFSET, btr1); + + netdev_dbg(ndev, "BRPR=0x%08x, BTR=0x%08x\n", + priv->read_reg(priv, XCAN_BRPR_OFFSET), + priv->read_reg(priv, XCAN_BTR_OFFSET)); + + return 0; +} + +/** + * xcan_chip_start - This the drivers start routine + * @ndev: Pointer to net_device structure + * + * This is the drivers start routine. + * Based on the State of the CAN device it puts + * the CAN device into a proper mode. + * + * Return: 0 on success and failure value on error + */ +static int xcan_chip_start(struct net_device *ndev) +{ + struct xcan_priv *priv = netdev_priv(ndev); + u32 err, reg_msr, reg_sr_mask; + unsigned long timeout; + + /* Check if it is in reset mode */ + err = set_reset_mode(ndev); + if (err < 0) + return err; + + err = xcan_set_bittiming(ndev); + if (err < 0) + return err; + + /* Enable interrupts */ + priv->write_reg(priv, XCAN_IER_OFFSET, XCAN_INTR_ALL); + + /* Check whether it is loopback mode or normal mode */ + if (priv->can.ctrlmode & CAN_CTRLMODE_LOOPBACK) { + reg_msr = XCAN_MSR_LBACK_MASK; + reg_sr_mask = XCAN_SR_LBACK_MASK; + } else { + reg_msr = 0x0; + reg_sr_mask = XCAN_SR_NORMAL_MASK; + } + + priv->write_reg(priv, XCAN_MSR_OFFSET, reg_msr); + priv->write_reg(priv, XCAN_SRR_OFFSET, XCAN_SRR_CEN_MASK); + + timeout = jiffies + XCAN_TIMEOUT; + while (!(priv->read_reg(priv, XCAN_SR_OFFSET) & reg_sr_mask)) { + if (time_after(jiffies, timeout)) { + netdev_warn(ndev, + "timed out for correct mode\n"); + return -ETIMEDOUT; + } + } + netdev_dbg(ndev, "status:#x%08x\n", + priv->read_reg(priv, XCAN_SR_OFFSET)); + + priv->can.state = CAN_STATE_ERROR_ACTIVE; + return 0; +} + +/** + * xcan_do_set_mode - This sets the mode of the driver + * @ndev: Pointer to net_device structure + * @mode: Tells the mode of the driver + * + * This check the drivers state and calls the + * the corresponding modes to set. + * + * Return: 0 on success and failure value on error + */ +static int xcan_do_set_mode(struct net_device *ndev, enum can_mode mode) +{ + int ret; + + switch (mode) { + case CAN_MODE_START: + ret = xcan_chip_start(ndev); + if (ret < 0) { + netdev_err(ndev, "xcan_chip_start failed!\n"); + return ret; + } + netif_wake_queue(ndev); + break; + default: + ret = -EOPNOTSUPP; + break; + } + + return ret; +} + +/** + * xcan_start_xmit - Starts the transmission + * @skb: sk_buff pointer that contains data to be Txed + * @ndev: Pointer to net_device structure + * + * This function is invoked from upper layers to initiate transmission. This + * function uses the next available free txbuff and populates their fields to + * start the transmission. + * + * Return: 0 on success and failure value on error + */ +static int xcan_start_xmit(struct sk_buff *skb, struct net_device *ndev) +{ + struct xcan_priv *priv = netdev_priv(ndev); + struct net_device_stats *stats = &ndev->stats; + struct can_frame *cf = (struct can_frame *)skb->data; + u32 id, dlc, data[2] = {0, 0}; + + if (can_dropped_invalid_skb(ndev, skb)) + return NETDEV_TX_OK; + + /* Check if the TX buffer is full */ + if (unlikely(priv->read_reg(priv, XCAN_SR_OFFSET) & + XCAN_SR_TXFLL_MASK)) { + netif_stop_queue(ndev); + netdev_err(ndev, "BUG!, TX FIFO full when queue awake!\n"); + return NETDEV_TX_BUSY; + } + + /* Watch carefully on the bit sequence */ + if (cf->can_id & CAN_EFF_FLAG) { + /* Extended CAN ID format */ + id = ((cf->can_id & CAN_EFF_MASK) << XCAN_IDR_ID2_SHIFT) & + XCAN_IDR_ID2_MASK; + id |= (((cf->can_id & CAN_EFF_MASK) >> + (CAN_EFF_ID_BITS-CAN_SFF_ID_BITS)) << + XCAN_IDR_ID1_SHIFT) & XCAN_IDR_ID1_MASK; + + /* The substibute remote TX request bit should be "1" + * for extended frames as in the Xilinx CAN datasheet + */ + id |= XCAN_IDR_IDE_MASK | XCAN_IDR_SRR_MASK; + + if (cf->can_id & CAN_RTR_FLAG) + /* Extended frames remote TX request */ + id |= XCAN_IDR_RTR_MASK; + } else { + /* Standard CAN ID format */ + id = ((cf->can_id & CAN_SFF_MASK) << XCAN_IDR_ID1_SHIFT) & + XCAN_IDR_ID1_MASK; + + if (cf->can_id & CAN_RTR_FLAG) + /* Standard frames remote TX request */ + id |= XCAN_IDR_SRR_MASK; + } + + dlc = cf->can_dlc << XCAN_DLCR_DLC_SHIFT; + + if (cf->can_dlc > 0) + data[0] = be32_to_cpup((__be32 *)(cf->data + 0)); + if (cf->can_dlc > 4) + data[1] = be32_to_cpup((__be32 *)(cf->data + 4)); + + can_put_echo_skb(skb, ndev, priv->tx_head % priv->tx_max); + priv->tx_head++; + + /* Write the Frame to Xilinx CAN TX FIFO */ + priv->write_reg(priv, XCAN_TXFIFO_ID_OFFSET, id); + /* If the CAN frame is RTR frame this write triggers tranmission */ + priv->write_reg(priv, XCAN_TXFIFO_DLC_OFFSET, dlc); + if (!(cf->can_id & CAN_RTR_FLAG)) { + priv->write_reg(priv, XCAN_TXFIFO_DW1_OFFSET, data[0]); + /* If the CAN frame is Standard/Extended frame this + * write triggers tranmission + */ + priv->write_reg(priv, XCAN_TXFIFO_DW2_OFFSET, data[1]); + stats->tx_bytes += cf->can_dlc; + } + + /* Check if the TX buffer is full */ + if ((priv->tx_head - priv->tx_tail) == priv->tx_max) + netif_stop_queue(ndev); + + return NETDEV_TX_OK; +} + +/** + * xcan_rx - Is called from CAN isr to complete the received + * frame processing + * @ndev: Pointer to net_device structure + * + * This function is invoked from the CAN isr(poll) to process the Rx frames. It + * does minimal processing and invokes "netif_receive_skb" to complete further + * processing. + * Return: 1 on success and 0 on failure. + */ +static int xcan_rx(struct net_device *ndev) +{ + struct xcan_priv *priv = netdev_priv(ndev); + struct net_device_stats *stats = &ndev->stats; + struct can_frame *cf; + struct sk_buff *skb; + u32 id_xcan, dlc, data[2] = {0, 0}; + + skb = alloc_can_skb(ndev, &cf); + if (unlikely(!skb)) { + stats->rx_dropped++; + return 0; + } + + /* Read a frame from Xilinx zynq CANPS */ + id_xcan = priv->read_reg(priv, XCAN_RXFIFO_ID_OFFSET); + dlc = priv->read_reg(priv, XCAN_RXFIFO_DLC_OFFSET) >> + XCAN_DLCR_DLC_SHIFT; + + /* Change Xilinx CAN data length format to socketCAN data format */ + cf->can_dlc = get_can_dlc(dlc); + + /* Change Xilinx CAN ID format to socketCAN ID format */ + if (id_xcan & XCAN_IDR_IDE_MASK) { + /* The received frame is an Extended format frame */ + cf->can_id = (id_xcan & XCAN_IDR_ID1_MASK) >> 3; + cf->can_id |= (id_xcan & XCAN_IDR_ID2_MASK) >> + XCAN_IDR_ID2_SHIFT; + cf->can_id |= CAN_EFF_FLAG; + if (id_xcan & XCAN_IDR_RTR_MASK) + cf->can_id |= CAN_RTR_FLAG; + } else { + /* The received frame is a standard format frame */ + cf->can_id = (id_xcan & XCAN_IDR_ID1_MASK) >> + XCAN_IDR_ID1_SHIFT; + if (id_xcan & XCAN_IDR_SRR_MASK) + cf->can_id |= CAN_RTR_FLAG; + } + + if (!(id_xcan & XCAN_IDR_SRR_MASK)) { + data[0] = priv->read_reg(priv, XCAN_RXFIFO_DW1_OFFSET); + data[1] = priv->read_reg(priv, XCAN_RXFIFO_DW2_OFFSET); + + /* Change Xilinx CAN data format to socketCAN data format */ + if (cf->can_dlc > 0) + *(__be32 *)(cf->data) = cpu_to_be32(data[0]); + if (cf->can_dlc > 4) + *(__be32 *)(cf->data + 4) = cpu_to_be32(data[1]); + } + + stats->rx_bytes += cf->can_dlc; + stats->rx_packets++; + netif_receive_skb(skb); + + return 1; +} + +/** + * xcan_err_interrupt - error frame Isr + * @ndev: net_device pointer + * @isr: interrupt status register value + * + * This is the CAN error interrupt and it will + * check the the type of error and forward the error + * frame to upper layers. + */ +static void xcan_err_interrupt(struct net_device *ndev, u32 isr) +{ + struct xcan_priv *priv = netdev_priv(ndev); + struct net_device_stats *stats = &ndev->stats; + struct can_frame *cf; + struct sk_buff *skb; + u32 err_status, status, txerr = 0, rxerr = 0; + + skb = alloc_can_err_skb(ndev, &cf); + + err_status = priv->read_reg(priv, XCAN_ESR_OFFSET); + priv->write_reg(priv, XCAN_ESR_OFFSET, err_status); + txerr = priv->read_reg(priv, XCAN_ECR_OFFSET) & XCAN_ECR_TEC_MASK; + rxerr = ((priv->read_reg(priv, XCAN_ECR_OFFSET) & + XCAN_ECR_REC_MASK) >> XCAN_ESR_REC_SHIFT); + status = priv->read_reg(priv, XCAN_SR_OFFSET); + + if (isr & XCAN_IXR_BSOFF_MASK) { + priv->can.state = CAN_STATE_BUS_OFF; + priv->can.can_stats.bus_off++; + /* Leave device in Config Mode in bus-off state */ + priv->write_reg(priv, XCAN_SRR_OFFSET, XCAN_SRR_RESET_MASK); + can_bus_off(ndev); + if (skb) + cf->can_id |= CAN_ERR_BUSOFF; + } else if ((status & XCAN_SR_ESTAT_MASK) == XCAN_SR_ESTAT_MASK) { + priv->can.state = CAN_STATE_ERROR_PASSIVE; + priv->can.can_stats.error_passive++; + if (skb) { + cf->can_id |= CAN_ERR_CRTL; + cf->data[1] = (rxerr > 127) ? + CAN_ERR_CRTL_RX_PASSIVE : + CAN_ERR_CRTL_TX_PASSIVE; + cf->data[6] = txerr; + cf->data[7] = rxerr; + } + } else if (status & XCAN_SR_ERRWRN_MASK) { + priv->can.state = CAN_STATE_ERROR_WARNING; + priv->can.can_stats.error_warning++; + if (skb) { + cf->can_id |= CAN_ERR_CRTL; + cf->data[1] |= (txerr > rxerr) ? + CAN_ERR_CRTL_TX_WARNING : + CAN_ERR_CRTL_RX_WARNING; + cf->data[6] = txerr; + cf->data[7] = rxerr; + } + } + + /* Check for Arbitration lost interrupt */ + if (isr & XCAN_IXR_ARBLST_MASK) { + priv->can.can_stats.arbitration_lost++; + if (skb) { + cf->can_id |= CAN_ERR_LOSTARB; + cf->data[0] = CAN_ERR_LOSTARB_UNSPEC; + } + } + + /* Check for RX FIFO Overflow interrupt */ + if (isr & XCAN_IXR_RXOFLW_MASK) { + stats->rx_over_errors++; + stats->rx_errors++; + priv->write_reg(priv, XCAN_SRR_OFFSET, XCAN_SRR_RESET_MASK); + if (skb) { + cf->can_id |= CAN_ERR_CRTL; + cf->data[1] |= CAN_ERR_CRTL_RX_OVERFLOW; + } + } + + /* Check for error interrupt */ + if (isr & XCAN_IXR_ERROR_MASK) { + if (skb) { + cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR; + cf->data[2] |= CAN_ERR_PROT_UNSPEC; + } + + /* Check for Ack error interrupt */ + if (err_status & XCAN_ESR_ACKER_MASK) { + stats->tx_errors++; + if (skb) { + cf->can_id |= CAN_ERR_ACK; + cf->data[3] |= CAN_ERR_PROT_LOC_ACK; + } + } + + /* Check for Bit error interrupt */ + if (err_status & XCAN_ESR_BERR_MASK) { + stats->tx_errors++; + if (skb) { + cf->can_id |= CAN_ERR_PROT; + cf->data[2] = CAN_ERR_PROT_BIT; + } + } + + /* Check for Stuff error interrupt */ + if (err_status & XCAN_ESR_STER_MASK) { + stats->rx_errors++; + if (skb) { + cf->can_id |= CAN_ERR_PROT; + cf->data[2] = CAN_ERR_PROT_STUFF; + } + } + + /* Check for Form error interrupt */ + if (err_status & XCAN_ESR_FMER_MASK) { + stats->rx_errors++; + if (skb) { + cf->can_id |= CAN_ERR_PROT; + cf->data[2] = CAN_ERR_PROT_FORM; + } + } + + /* Check for CRC error interrupt */ + if (err_status & XCAN_ESR_CRCER_MASK) { + stats->rx_errors++; + if (skb) { + cf->can_id |= CAN_ERR_PROT; + cf->data[3] = CAN_ERR_PROT_LOC_CRC_SEQ | + CAN_ERR_PROT_LOC_CRC_DEL; + } + } + priv->can.can_stats.bus_error++; + } + + if (skb) { + stats->rx_packets++; + stats->rx_bytes += cf->can_dlc; + netif_rx(skb); + } + + netdev_dbg(ndev, "%s: error status register:0x%x\n", + __func__, priv->read_reg(priv, XCAN_ESR_OFFSET)); +} + +/** + * xcan_state_interrupt - It will check the state of the CAN device + * @ndev: net_device pointer + * @isr: interrupt status register value + * + * This will checks the state of the CAN device + * and puts the device into appropriate state. + */ +static void xcan_state_interrupt(struct net_device *ndev, u32 isr) +{ + struct xcan_priv *priv = netdev_priv(ndev); + + /* Check for Sleep interrupt if set put CAN device in sleep state */ + if (isr & XCAN_IXR_SLP_MASK) + priv->can.state = CAN_STATE_SLEEPING; + + /* Check for Wake up interrupt if set put CAN device in Active state */ + if (isr & XCAN_IXR_WKUP_MASK) + priv->can.state = CAN_STATE_ERROR_ACTIVE; +} + +/** + * xcan_rx_poll - Poll routine for rx packets (NAPI) + * @napi: napi structure pointer + * @quota: Max number of rx packets to be processed. + * + * This is the poll routine for rx part. + * It will process the packets maximux quota value. + * + * Return: number of packets received + */ +static int xcan_rx_poll(struct napi_struct *napi, int quota) +{ + struct net_device *ndev = napi->dev; + struct xcan_priv *priv = netdev_priv(ndev); + u32 isr, ier; + int work_done = 0; + + isr = priv->read_reg(priv, XCAN_ISR_OFFSET); + while ((isr & XCAN_IXR_RXNEMP_MASK) && (work_done < quota)) { + if (isr & XCAN_IXR_RXOK_MASK) { + priv->write_reg(priv, XCAN_ICR_OFFSET, + XCAN_IXR_RXOK_MASK); + work_done += xcan_rx(ndev); + } else { + priv->write_reg(priv, XCAN_ICR_OFFSET, + XCAN_IXR_RXNEMP_MASK); + break; + } + priv->write_reg(priv, XCAN_ICR_OFFSET, XCAN_IXR_RXNEMP_MASK); + isr = priv->read_reg(priv, XCAN_ISR_OFFSET); + } + + if (work_done) + can_led_event(ndev, CAN_LED_EVENT_RX); + + if (work_done < quota) { + napi_complete(napi); + ier = priv->read_reg(priv, XCAN_IER_OFFSET); + ier |= (XCAN_IXR_RXOK_MASK | XCAN_IXR_RXNEMP_MASK); + priv->write_reg(priv, XCAN_IER_OFFSET, ier); + } + return work_done; +} + +/** + * xcan_tx_interrupt - Tx Done Isr + * @ndev: net_device pointer + * @isr: Interrupt status register value + */ +static void xcan_tx_interrupt(struct net_device *ndev, u32 isr) +{ + struct xcan_priv *priv = netdev_priv(ndev); + struct net_device_stats *stats = &ndev->stats; + + while ((priv->tx_head - priv->tx_tail > 0) && + (isr & XCAN_IXR_TXOK_MASK)) { + priv->write_reg(priv, XCAN_ICR_OFFSET, XCAN_IXR_TXOK_MASK); + can_get_echo_skb(ndev, priv->tx_tail % + priv->tx_max); + priv->tx_tail++; + stats->tx_packets++; + isr = priv->read_reg(priv, XCAN_ISR_OFFSET); + } + can_led_event(ndev, CAN_LED_EVENT_TX); + netif_wake_queue(ndev); +} + +/** + * xcan_interrupt - CAN Isr + * @irq: irq number + * @dev_id: device id poniter + * + * This is the xilinx CAN Isr. It checks for the type of interrupt + * and invokes the corresponding ISR. + * + * Return: + * IRQ_NONE - If CAN device is in sleep mode, IRQ_HANDLED otherwise + */ +static irqreturn_t xcan_interrupt(int irq, void *dev_id) +{ + struct net_device *ndev = (struct net_device *)dev_id; + struct xcan_priv *priv = netdev_priv(ndev); + u32 isr, ier; + + /* Get the interrupt status from Xilinx CAN */ + isr = priv->read_reg(priv, XCAN_ISR_OFFSET); + if (!isr) + return IRQ_NONE; + + /* Check for the type of interrupt and Processing it */ + if (isr & (XCAN_IXR_SLP_MASK | XCAN_IXR_WKUP_MASK)) { + priv->write_reg(priv, XCAN_ICR_OFFSET, (XCAN_IXR_SLP_MASK | + XCAN_IXR_WKUP_MASK)); + xcan_state_interrupt(ndev, isr); + } + + /* Check for Tx interrupt and Processing it */ + if (isr & XCAN_IXR_TXOK_MASK) + xcan_tx_interrupt(ndev, isr); + + /* Check for the type of error interrupt and Processing it */ + if (isr & (XCAN_IXR_ERROR_MASK | XCAN_IXR_RXOFLW_MASK | + XCAN_IXR_BSOFF_MASK | XCAN_IXR_ARBLST_MASK)) { + priv->write_reg(priv, XCAN_ICR_OFFSET, (XCAN_IXR_ERROR_MASK | + XCAN_IXR_RXOFLW_MASK | XCAN_IXR_BSOFF_MASK | + XCAN_IXR_ARBLST_MASK)); + xcan_err_interrupt(ndev, isr); + } + + /* Check for the type of receive interrupt and Processing it */ + if (isr & (XCAN_IXR_RXNEMP_MASK | XCAN_IXR_RXOK_MASK)) { + ier = priv->read_reg(priv, XCAN_IER_OFFSET); + ier &= ~(XCAN_IXR_RXNEMP_MASK | XCAN_IXR_RXOK_MASK); + priv->write_reg(priv, XCAN_IER_OFFSET, ier); + napi_schedule(&priv->napi); + } + return IRQ_HANDLED; +} + +/** + * xcan_chip_stop - Driver stop routine + * @ndev: Pointer to net_device structure + * + * This is the drivers stop routine. It will disable the + * interrupts and put the device into configuration mode. + */ +static void xcan_chip_stop(struct net_device *ndev) +{ + struct xcan_priv *priv = netdev_priv(ndev); + u32 ier; + + /* Disable interrupts and leave the can in configuration mode */ + ier = priv->read_reg(priv, XCAN_IER_OFFSET); + ier &= ~XCAN_INTR_ALL; + priv->write_reg(priv, XCAN_IER_OFFSET, ier); + priv->write_reg(priv, XCAN_SRR_OFFSET, XCAN_SRR_RESET_MASK); + priv->can.state = CAN_STATE_STOPPED; +} + +/** + * xcan_open - Driver open routine + * @ndev: Pointer to net_device structure + * + * This is the driver open routine. + * Return: 0 on success and failure value on error + */ +static int xcan_open(struct net_device *ndev) +{ + struct xcan_priv *priv = netdev_priv(ndev); + int ret; + + ret = request_irq(ndev->irq, xcan_interrupt, priv->irq_flags, + ndev->name, ndev); + if (ret < 0) { + netdev_err(ndev, "irq allocation for CAN failed\n"); + goto err; + } + + ret = clk_prepare_enable(priv->can_clk); + if (ret) { + netdev_err(ndev, "unable to enable device clock\n"); + goto err_irq; + } + + ret = clk_prepare_enable(priv->bus_clk); + if (ret) { + netdev_err(ndev, "unable to enable bus clock\n"); + goto err_can_clk; + } + + /* Set chip into reset mode */ + ret = set_reset_mode(ndev); + if (ret < 0) { + netdev_err(ndev, "mode resetting failed!\n"); + goto err_bus_clk; + } + + /* Common open */ + ret = open_candev(ndev); + if (ret) + goto err_bus_clk; + + ret = xcan_chip_start(ndev); + if (ret < 0) { + netdev_err(ndev, "xcan_chip_start failed!\n"); + goto err_candev; + } + + can_led_event(ndev, CAN_LED_EVENT_OPEN); + napi_enable(&priv->napi); + netif_start_queue(ndev); + + return 0; + +err_candev: + close_candev(ndev); +err_bus_clk: + clk_disable_unprepare(priv->bus_clk); +err_can_clk: + clk_disable_unprepare(priv->can_clk); +err_irq: + free_irq(ndev->irq, ndev); +err: + return ret; +} + +/** + * xcan_close - Driver close routine + * @ndev: Pointer to net_device structure + * + * Return: 0 always + */ +static int xcan_close(struct net_device *ndev) +{ + struct xcan_priv *priv = netdev_priv(ndev); + + netif_stop_queue(ndev); + napi_disable(&priv->napi); + xcan_chip_stop(ndev); + clk_disable_unprepare(priv->bus_clk); + clk_disable_unprepare(priv->can_clk); + free_irq(ndev->irq, ndev); + close_candev(ndev); + + can_led_event(ndev, CAN_LED_EVENT_STOP); + + return 0; +} + +/** + * xcan_get_berr_counter - error counter routine + * @ndev: Pointer to net_device structure + * @bec: Pointer to can_berr_counter structure + * + * This is the driver error counter routine. + * Return: 0 on success and failure value on error + */ +static int xcan_get_berr_counter(const struct net_device *ndev, + struct can_berr_counter *bec) +{ + struct xcan_priv *priv = netdev_priv(ndev); + int ret; + + ret = clk_prepare_enable(priv->can_clk); + if (ret) + goto err; + + ret = clk_prepare_enable(priv->bus_clk); + if (ret) + goto err_clk; + + bec->txerr = priv->read_reg(priv, XCAN_ECR_OFFSET) & XCAN_ECR_TEC_MASK; + bec->rxerr = ((priv->read_reg(priv, XCAN_ECR_OFFSET) & + XCAN_ECR_REC_MASK) >> XCAN_ESR_REC_SHIFT); + + clk_disable_unprepare(priv->bus_clk); + clk_disable_unprepare(priv->can_clk); + + return 0; + +err_clk: + clk_disable_unprepare(priv->can_clk); +err: + return ret; +} + + +static const struct net_device_ops xcan_netdev_ops = { + .ndo_open = xcan_open, + .ndo_stop = xcan_close, + .ndo_start_xmit = xcan_start_xmit, +}; + +/** + * xcan_suspend - Suspend method for the driver + * @dev: Address of the platform_device structure + * + * Put the driver into low power mode. + * Return: 0 always + */ +static int __maybe_unused xcan_suspend(struct device *dev) +{ + struct platform_device *pdev = dev_get_drvdata(dev); + struct net_device *ndev = platform_get_drvdata(pdev); + struct xcan_priv *priv = netdev_priv(ndev); + + if (netif_running(ndev)) { + netif_stop_queue(ndev); + netif_device_detach(ndev); + } + + priv->write_reg(priv, XCAN_MSR_OFFSET, XCAN_MSR_SLEEP_MASK); + priv->can.state = CAN_STATE_SLEEPING; + + clk_disable(priv->bus_clk); + clk_disable(priv->can_clk); + + return 0; +} + +/** + * xcan_resume - Resume from suspend + * @dev: Address of the platformdevice structure + * + * Resume operation after suspend. + * Return: 0 on success and failure value on error + */ +static int __maybe_unused xcan_resume(struct device *dev) +{ + struct platform_device *pdev = dev_get_drvdata(dev); + struct net_device *ndev = platform_get_drvdata(pdev); + struct xcan_priv *priv = netdev_priv(ndev); + int ret; + + ret = clk_enable(priv->bus_clk); + if (ret) { + dev_err(dev, "Cannot enable clock.\n"); + return ret; + } + ret = clk_enable(priv->can_clk); + if (ret) { + dev_err(dev, "Cannot enable clock.\n"); + clk_disable_unprepare(priv->bus_clk); + return ret; + } + + priv->write_reg(priv, XCAN_MSR_OFFSET, 0); + priv->write_reg(priv, XCAN_SRR_OFFSET, XCAN_SRR_CEN_MASK); + priv->can.state = CAN_STATE_ERROR_ACTIVE; + + if (netif_running(ndev)) { + netif_device_attach(ndev); + netif_start_queue(ndev); + } + + return 0; +} + +static SIMPLE_DEV_PM_OPS(xcan_dev_pm_ops, xcan_suspend, xcan_resume); + +/** + * xcan_probe - Platform registration call + * @pdev: Handle to the platform device structure + * + * This function does all the memory allocation and registration for the CAN + * device. + * + * Return: 0 on success and failure value on error + */ +static int xcan_probe(struct platform_device *pdev) +{ + struct resource *res; /* IO mem resources */ + struct net_device *ndev; + struct xcan_priv *priv; + void __iomem *addr; + int ret, rx_max, tx_max; + + /* Get the virtual base address for the device */ + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + addr = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(addr)) { + ret = PTR_ERR(addr); + goto err; + } + + ret = of_property_read_u32(pdev->dev.of_node, "tx-fifo-depth", &tx_max); + if (ret < 0) + goto err; + + ret = of_property_read_u32(pdev->dev.of_node, "rx-fifo-depth", &rx_max); + if (ret < 0) + goto err; + + /* Create a CAN device instance */ + ndev = alloc_candev(sizeof(struct xcan_priv), tx_max); + if (!ndev) + return -ENOMEM; + + priv = netdev_priv(ndev); + priv->dev = ndev; + priv->can.bittiming_const = &xcan_bittiming_const; + priv->can.do_set_mode = xcan_do_set_mode; + priv->can.do_get_berr_counter = xcan_get_berr_counter; + priv->can.ctrlmode_supported = CAN_CTRLMODE_LOOPBACK | + CAN_CTRLMODE_BERR_REPORTING; + priv->reg_base = addr; + priv->tx_max = tx_max; + + /* Get IRQ for the device */ + ndev->irq = platform_get_irq(pdev, 0); + ndev->flags |= IFF_ECHO; /* We support local echo */ + + platform_set_drvdata(pdev, ndev); + SET_NETDEV_DEV(ndev, &pdev->dev); + ndev->netdev_ops = &xcan_netdev_ops; + + /* Getting the CAN can_clk info */ + priv->can_clk = devm_clk_get(&pdev->dev, "can_clk"); + if (IS_ERR(priv->can_clk)) { + dev_err(&pdev->dev, "Device clock not found.\n"); + ret = PTR_ERR(priv->can_clk); + goto err_free; + } + /* Check for type of CAN device */ + if (of_device_is_compatible(pdev->dev.of_node, + "xlnx,zynq-can-1.0")) { + priv->bus_clk = devm_clk_get(&pdev->dev, "pclk"); + if (IS_ERR(priv->bus_clk)) { + dev_err(&pdev->dev, "bus clock not found\n"); + ret = PTR_ERR(priv->bus_clk); + goto err_free; + } + } else { + priv->bus_clk = devm_clk_get(&pdev->dev, "s_axi_aclk"); + if (IS_ERR(priv->bus_clk)) { + dev_err(&pdev->dev, "bus clock not found\n"); + ret = PTR_ERR(priv->bus_clk); + goto err_free; + } + } + + ret = clk_prepare_enable(priv->can_clk); + if (ret) { + dev_err(&pdev->dev, "unable to enable device clock\n"); + goto err_free; + } + + ret = clk_prepare_enable(priv->bus_clk); + if (ret) { + dev_err(&pdev->dev, "unable to enable bus clock\n"); + goto err_unprepare_disable_dev; + } + + priv->write_reg = xcan_write_reg_le; + priv->read_reg = xcan_read_reg_le; + + if (priv->read_reg(priv, XCAN_SR_OFFSET) != XCAN_SR_CONFIG_MASK) { + priv->write_reg = xcan_write_reg_be; + priv->read_reg = xcan_read_reg_be; + } + + priv->can.clock.freq = clk_get_rate(priv->can_clk); + + netif_napi_add(ndev, &priv->napi, xcan_rx_poll, rx_max); + + ret = register_candev(ndev); + if (ret) { + dev_err(&pdev->dev, "fail to register failed (err=%d)\n", ret); + goto err_unprepare_disable_busclk; + } + + devm_can_led_init(ndev); + clk_disable_unprepare(priv->bus_clk); + clk_disable_unprepare(priv->can_clk); + netdev_dbg(ndev, "reg_base=0x%p irq=%d clock=%d, tx fifo depth:%d\n", + priv->reg_base, ndev->irq, priv->can.clock.freq, + priv->tx_max); + + return 0; + +err_unprepare_disable_busclk: + clk_disable_unprepare(priv->bus_clk); +err_unprepare_disable_dev: + clk_disable_unprepare(priv->can_clk); +err_free: + free_candev(ndev); +err: + return ret; +} + +/** + * xcan_remove - Unregister the device after releasing the resources + * @pdev: Handle to the platform device structure + * + * This function frees all the resources allocated to the device. + * Return: 0 always + */ +static int xcan_remove(struct platform_device *pdev) +{ + struct net_device *ndev = platform_get_drvdata(pdev); + struct xcan_priv *priv = netdev_priv(ndev); + + if (set_reset_mode(ndev) < 0) + netdev_err(ndev, "mode resetting failed!\n"); + + unregister_candev(ndev); + netif_napi_del(&priv->napi); + free_candev(ndev); + + return 0; +} + +/* Match table for OF platform binding */ +static struct of_device_id xcan_of_match[] = { + { .compatible = "xlnx,zynq-can-1.0", }, + { .compatible = "xlnx,axi-can-1.00.a", }, + { /* end of list */ }, +}; +MODULE_DEVICE_TABLE(of, xcan_of_match); + +static struct platform_driver xcan_driver = { + .probe = xcan_probe, + .remove = xcan_remove, + .driver = { + .owner = THIS_MODULE, + .name = DRIVER_NAME, + .pm = &xcan_dev_pm_ops, + .of_match_table = xcan_of_match, + }, +}; + +module_platform_driver(xcan_driver); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Xilinx Inc"); +MODULE_DESCRIPTION("Xilinx CAN interface"); |