diff options
Diffstat (limited to 'drivers/mtd/ubi/Kconfig')
| -rw-r--r-- | drivers/mtd/ubi/Kconfig | 77 |
1 files changed, 63 insertions, 14 deletions
diff --git a/drivers/mtd/ubi/Kconfig b/drivers/mtd/ubi/Kconfig index 3cf193fb5e0..f0855ce08ed 100644 --- a/drivers/mtd/ubi/Kconfig +++ b/drivers/mtd/ubi/Kconfig @@ -27,20 +27,55 @@ config MTD_UBI_WL_THRESHOLD life-cycle less than 10000, the threshold should be lessened (e.g., to 128 or 256, although it does not have to be power of 2). -config MTD_UBI_BEB_RESERVE - int "Percentage of reserved eraseblocks for bad eraseblocks handling" - default 1 - range 0 25 +config MTD_UBI_BEB_LIMIT + int "Maximum expected bad eraseblock count per 1024 eraseblocks" + default 20 + range 0 768 help - If the MTD device admits of bad eraseblocks (e.g. NAND flash), UBI - reserves some amount of physical eraseblocks to handle new bad - eraseblocks. For example, if a flash physical eraseblock becomes bad, - UBI uses these reserved physical eraseblocks to relocate the bad one. - This option specifies how many physical eraseblocks will be reserved - for bad eraseblock handling (percents of total number of good flash - eraseblocks). If the underlying flash does not admit of bad - eraseblocks (e.g. NOR flash), this value is ignored and nothing is - reserved. Leave the default value if unsure. + This option specifies the maximum bad physical eraseblocks UBI + expects on the MTD device (per 1024 eraseblocks). If the underlying + flash does not admit of bad eraseblocks (e.g. NOR flash), this value + is ignored. + + NAND datasheets often specify the minimum and maximum NVM (Number of + Valid Blocks) for the flashes' endurance lifetime. The maximum + expected bad eraseblocks per 1024 eraseblocks then can be calculated + as "1024 * (1 - MinNVB / MaxNVB)", which gives 20 for most NANDs + (MaxNVB is basically the total count of eraseblocks on the chip). + + To put it differently, if this value is 20, UBI will try to reserve + about 1.9% of physical eraseblocks for bad blocks handling. And that + will be 1.9% of eraseblocks on the entire NAND chip, not just the MTD + partition UBI attaches. This means that if you have, say, a NAND + flash chip admits maximum 40 bad eraseblocks, and it is split on two + MTD partitions of the same size, UBI will reserve 40 eraseblocks when + attaching a partition. + + This option can be overridden by the "mtd=" UBI module parameter or + by the "attach" ioctl. + + Leave the default value if unsure. + +config MTD_UBI_FASTMAP + bool "UBI Fastmap (Experimental feature)" + default n + help + Important: this feature is experimental so far and the on-flash + format for fastmap may change in the next kernel versions + + Fastmap is a mechanism which allows attaching an UBI device + in nearly constant time. Instead of scanning the whole MTD device it + only has to locate a checkpoint (called fastmap) on the device. + The on-flash fastmap contains all information needed to attach + the device. Using fastmap makes only sense on large devices where + attaching by scanning takes long. UBI will not automatically install + a fastmap on old images, but you can set the UBI module parameter + fm_autoconvert to 1 if you want so. Please note that fastmap-enabled + images are still usable with UBI implementations without + fastmap support. On typical flash devices the whole fastmap fits + into one PEB. UBI will reserve PEBs to hold two fastmaps. + + If in doubt, say "N". config MTD_UBI_GLUEBI tristate "MTD devices emulation driver (gluebi)" @@ -52,6 +87,20 @@ config MTD_UBI_GLUEBI work on top of UBI. Do not enable this unless you use legacy software. -source "drivers/mtd/ubi/Kconfig.debug" +config MTD_UBI_BLOCK + bool "Read-only block devices on top of UBI volumes" + default n + depends on BLOCK + help + This option enables read-only UBI block devices support. UBI block + devices will be layered on top of UBI volumes, which means that the + UBI driver will transparently handle things like bad eraseblocks and + bit-flips. You can put any block-oriented file system on top of UBI + volumes in read-only mode (e.g., ext4), but it is probably most + practical for read-only file systems, like squashfs. + + When selected, this feature will be built in the UBI driver. + + If in doubt, say "N". endif # MTD_UBI |