diff options
Diffstat (limited to 'drivers/mtd/nand/omap2.c')
| -rw-r--r-- | drivers/mtd/nand/omap2.c | 1206 |
1 files changed, 833 insertions, 373 deletions
diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c index 0002d5e94f0..f0ed92e210a 100644 --- a/drivers/mtd/nand/omap2.c +++ b/drivers/mtd/nand/omap2.c @@ -22,10 +22,11 @@ #include <linux/omap-dma.h> #include <linux/io.h> #include <linux/slab.h> +#include <linux/of.h> +#include <linux/of_device.h> -#ifdef CONFIG_MTD_NAND_OMAP_BCH -#include <linux/bch.h> -#endif +#include <linux/mtd/nand_bch.h> +#include <linux/platform_data/elm.h> #include <linux/platform_data/mtd-nand-omap2.h> @@ -117,19 +118,36 @@ #define OMAP24XX_DMA_GPMC 4 +#define SECTOR_BYTES 512 +/* 4 bit padding to make byte aligned, 56 = 52 + 4 */ +#define BCH4_BIT_PAD 4 + +/* GPMC ecc engine settings for read */ +#define BCH_WRAPMODE_1 1 /* BCH wrap mode 1 */ +#define BCH8R_ECC_SIZE0 0x1a /* ecc_size0 = 26 */ +#define BCH8R_ECC_SIZE1 0x2 /* ecc_size1 = 2 */ +#define BCH4R_ECC_SIZE0 0xd /* ecc_size0 = 13 */ +#define BCH4R_ECC_SIZE1 0x3 /* ecc_size1 = 3 */ + +/* GPMC ecc engine settings for write */ +#define BCH_WRAPMODE_6 6 /* BCH wrap mode 6 */ +#define BCH_ECC_SIZE0 0x0 /* ecc_size0 = 0, no oob protection */ +#define BCH_ECC_SIZE1 0x20 /* ecc_size1 = 32 */ + +#define BADBLOCK_MARKER_LENGTH 2 + +#ifdef CONFIG_MTD_NAND_OMAP_BCH +static u_char bch16_vector[] = {0xf5, 0x24, 0x1c, 0xd0, 0x61, 0xb3, 0xf1, 0x55, + 0x2e, 0x2c, 0x86, 0xa3, 0xed, 0x36, 0x1b, 0x78, + 0x48, 0x76, 0xa9, 0x3b, 0x97, 0xd1, 0x7a, 0x93, + 0x07, 0x0e}; +static u_char bch8_vector[] = {0xf3, 0xdb, 0x14, 0x16, 0x8b, 0xd2, 0xbe, 0xcc, + 0xac, 0x6b, 0xff, 0x99, 0x7b}; +static u_char bch4_vector[] = {0x00, 0x6b, 0x31, 0xdd, 0x41, 0xbc, 0x10}; +#endif + /* oob info generated runtime depending on ecc algorithm and layout selected */ static struct nand_ecclayout omap_oobinfo; -/* Define some generic bad / good block scan pattern which are used - * while scanning a device for factory marked good / bad blocks - */ -static uint8_t scan_ff_pattern[] = { 0xff }; -static struct nand_bbt_descr bb_descrip_flashbased = { - .options = NAND_BBT_SCANEMPTY | NAND_BBT_SCANALLPAGES, - .offs = 0, - .len = 1, - .pattern = scan_ff_pattern, -}; - struct omap_nand_info { struct nand_hw_control controller; @@ -140,7 +158,7 @@ struct omap_nand_info { int gpmc_cs; unsigned long phys_base; - unsigned long mem_size; + enum omap_ecc ecc_opt; struct completion comp; struct dma_chan *dma; int gpmc_irq_fifo; @@ -152,11 +170,9 @@ struct omap_nand_info { u_char *buf; int buf_len; struct gpmc_nand_regs reg; - -#ifdef CONFIG_MTD_NAND_OMAP_BCH - struct bch_control *bch; - struct nand_ecclayout ecclayout; -#endif + /* fields specific for BCHx_HW ECC scheme */ + struct device *elm_dev; + struct device_node *of_node; }; /** @@ -990,9 +1006,9 @@ static int omap_wait(struct mtd_info *mtd, struct nand_chip *chip) int status, state = this->state; if (state == FL_ERASING) - timeo += (HZ * 400) / 1000; + timeo += msecs_to_jiffies(400); else - timeo += (HZ * 20) / 1000; + timeo += msecs_to_jiffies(20); writeb(NAND_CMD_STATUS & 0xFF, info->reg.gpmc_nand_command); while (time_before(jiffies, timeo)) { @@ -1025,46 +1041,112 @@ static int omap_dev_ready(struct mtd_info *mtd) } } -#ifdef CONFIG_MTD_NAND_OMAP_BCH - /** - * omap3_enable_hwecc_bch - Program OMAP3 GPMC to perform BCH ECC correction + * omap_enable_hwecc_bch - Program GPMC to perform BCH ECC calculation * @mtd: MTD device structure * @mode: Read/Write mode + * + * When using BCH, sector size is hardcoded to 512 bytes. + * Using wrapping mode 6 both for reading and writing if ELM module not uses + * for error correction. + * On writing, + * eccsize0 = 0 (no additional protected byte in spare area) + * eccsize1 = 32 (skip 32 nibbles = 16 bytes per sector in spare area) */ -static void omap3_enable_hwecc_bch(struct mtd_info *mtd, int mode) +static void __maybe_unused omap_enable_hwecc_bch(struct mtd_info *mtd, int mode) { - int nerrors; + unsigned int bch_type; unsigned int dev_width, nsectors; struct omap_nand_info *info = container_of(mtd, struct omap_nand_info, mtd); + enum omap_ecc ecc_opt = info->ecc_opt; struct nand_chip *chip = mtd->priv; - u32 val; - - nerrors = (info->nand.ecc.bytes == 13) ? 8 : 4; - dev_width = (chip->options & NAND_BUSWIDTH_16) ? 1 : 0; - nsectors = 1; - /* - * Program GPMC to perform correction on one 512-byte sector at a time. - * Using 4 sectors at a time (i.e. ecc.size = 2048) is also possible and - * gives a slight (5%) performance gain (but requires additional code). - */ + u32 val, wr_mode; + unsigned int ecc_size1, ecc_size0; + + /* GPMC configurations for calculating ECC */ + switch (ecc_opt) { + case OMAP_ECC_BCH4_CODE_HW_DETECTION_SW: + bch_type = 0; + nsectors = 1; + if (mode == NAND_ECC_READ) { + wr_mode = BCH_WRAPMODE_6; + ecc_size0 = BCH_ECC_SIZE0; + ecc_size1 = BCH_ECC_SIZE1; + } else { + wr_mode = BCH_WRAPMODE_6; + ecc_size0 = BCH_ECC_SIZE0; + ecc_size1 = BCH_ECC_SIZE1; + } + break; + case OMAP_ECC_BCH4_CODE_HW: + bch_type = 0; + nsectors = chip->ecc.steps; + if (mode == NAND_ECC_READ) { + wr_mode = BCH_WRAPMODE_1; + ecc_size0 = BCH4R_ECC_SIZE0; + ecc_size1 = BCH4R_ECC_SIZE1; + } else { + wr_mode = BCH_WRAPMODE_6; + ecc_size0 = BCH_ECC_SIZE0; + ecc_size1 = BCH_ECC_SIZE1; + } + break; + case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW: + bch_type = 1; + nsectors = 1; + if (mode == NAND_ECC_READ) { + wr_mode = BCH_WRAPMODE_6; + ecc_size0 = BCH_ECC_SIZE0; + ecc_size1 = BCH_ECC_SIZE1; + } else { + wr_mode = BCH_WRAPMODE_6; + ecc_size0 = BCH_ECC_SIZE0; + ecc_size1 = BCH_ECC_SIZE1; + } + break; + case OMAP_ECC_BCH8_CODE_HW: + bch_type = 1; + nsectors = chip->ecc.steps; + if (mode == NAND_ECC_READ) { + wr_mode = BCH_WRAPMODE_1; + ecc_size0 = BCH8R_ECC_SIZE0; + ecc_size1 = BCH8R_ECC_SIZE1; + } else { + wr_mode = BCH_WRAPMODE_6; + ecc_size0 = BCH_ECC_SIZE0; + ecc_size1 = BCH_ECC_SIZE1; + } + break; + case OMAP_ECC_BCH16_CODE_HW: + bch_type = 0x2; + nsectors = chip->ecc.steps; + if (mode == NAND_ECC_READ) { + wr_mode = 0x01; + ecc_size0 = 52; /* ECC bits in nibbles per sector */ + ecc_size1 = 0; /* non-ECC bits in nibbles per sector */ + } else { + wr_mode = 0x01; + ecc_size0 = 0; /* extra bits in nibbles per sector */ + ecc_size1 = 52; /* OOB bits in nibbles per sector */ + } + break; + default: + return; + } writel(ECC1, info->reg.gpmc_ecc_control); - /* - * When using BCH, sector size is hardcoded to 512 bytes. - * Here we are using wrapping mode 6 both for reading and writing, with: - * size0 = 0 (no additional protected byte in spare area) - * size1 = 32 (skip 32 nibbles = 16 bytes per sector in spare area) - */ - val = (32 << ECCSIZE1_SHIFT) | (0 << ECCSIZE0_SHIFT); + /* Configure ecc size for BCH */ + val = (ecc_size1 << ECCSIZE1_SHIFT) | (ecc_size0 << ECCSIZE0_SHIFT); writel(val, info->reg.gpmc_ecc_size_config); + dev_width = (chip->options & NAND_BUSWIDTH_16) ? 1 : 0; + /* BCH configuration */ val = ((1 << 16) | /* enable BCH */ - (((nerrors == 8) ? 1 : 0) << 12) | /* 8 or 4 bits */ - (0x06 << 8) | /* wrap mode = 6 */ + (bch_type << 12) | /* BCH4/BCH8/BCH16 */ + (wr_mode << 8) | /* wrap mode */ (dev_width << 7) | /* bus width */ (((nsectors-1) & 0x7) << 4) | /* number of sectors */ (info->gpmc_cs << 1) | /* ECC CS */ @@ -1072,274 +1154,496 @@ static void omap3_enable_hwecc_bch(struct mtd_info *mtd, int mode) writel(val, info->reg.gpmc_ecc_config); - /* clear ecc and enable bits */ + /* Clear ecc and enable bits */ writel(ECCCLEAR | ECC1, info->reg.gpmc_ecc_control); } +static u8 bch4_polynomial[] = {0x28, 0x13, 0xcc, 0x39, 0x96, 0xac, 0x7f}; +static u8 bch8_polynomial[] = {0xef, 0x51, 0x2e, 0x09, 0xed, 0x93, 0x9a, 0xc2, + 0x97, 0x79, 0xe5, 0x24, 0xb5}; + /** - * omap3_calculate_ecc_bch4 - Generate 7 bytes of ECC bytes - * @mtd: MTD device structure - * @dat: The pointer to data on which ecc is computed - * @ecc_code: The ecc_code buffer + * omap_calculate_ecc_bch - Generate bytes of ECC bytes + * @mtd: MTD device structure + * @dat: The pointer to data on which ecc is computed + * @ecc_code: The ecc_code buffer + * + * Support calculating of BCH4/8 ecc vectors for the page */ -static int omap3_calculate_ecc_bch4(struct mtd_info *mtd, const u_char *dat, - u_char *ecc_code) +static int __maybe_unused omap_calculate_ecc_bch(struct mtd_info *mtd, + const u_char *dat, u_char *ecc_calc) { struct omap_nand_info *info = container_of(mtd, struct omap_nand_info, mtd); - unsigned long nsectors, val1, val2; - int i; + int eccbytes = info->nand.ecc.bytes; + struct gpmc_nand_regs *gpmc_regs = &info->reg; + u8 *ecc_code; + unsigned long nsectors, bch_val1, bch_val2, bch_val3, bch_val4; + u32 val; + int i, j; nsectors = ((readl(info->reg.gpmc_ecc_config) >> 4) & 0x7) + 1; - for (i = 0; i < nsectors; i++) { + ecc_code = ecc_calc; + switch (info->ecc_opt) { + case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW: + case OMAP_ECC_BCH8_CODE_HW: + bch_val1 = readl(gpmc_regs->gpmc_bch_result0[i]); + bch_val2 = readl(gpmc_regs->gpmc_bch_result1[i]); + bch_val3 = readl(gpmc_regs->gpmc_bch_result2[i]); + bch_val4 = readl(gpmc_regs->gpmc_bch_result3[i]); + *ecc_code++ = (bch_val4 & 0xFF); + *ecc_code++ = ((bch_val3 >> 24) & 0xFF); + *ecc_code++ = ((bch_val3 >> 16) & 0xFF); + *ecc_code++ = ((bch_val3 >> 8) & 0xFF); + *ecc_code++ = (bch_val3 & 0xFF); + *ecc_code++ = ((bch_val2 >> 24) & 0xFF); + *ecc_code++ = ((bch_val2 >> 16) & 0xFF); + *ecc_code++ = ((bch_val2 >> 8) & 0xFF); + *ecc_code++ = (bch_val2 & 0xFF); + *ecc_code++ = ((bch_val1 >> 24) & 0xFF); + *ecc_code++ = ((bch_val1 >> 16) & 0xFF); + *ecc_code++ = ((bch_val1 >> 8) & 0xFF); + *ecc_code++ = (bch_val1 & 0xFF); + break; + case OMAP_ECC_BCH4_CODE_HW_DETECTION_SW: + case OMAP_ECC_BCH4_CODE_HW: + bch_val1 = readl(gpmc_regs->gpmc_bch_result0[i]); + bch_val2 = readl(gpmc_regs->gpmc_bch_result1[i]); + *ecc_code++ = ((bch_val2 >> 12) & 0xFF); + *ecc_code++ = ((bch_val2 >> 4) & 0xFF); + *ecc_code++ = ((bch_val2 & 0xF) << 4) | + ((bch_val1 >> 28) & 0xF); + *ecc_code++ = ((bch_val1 >> 20) & 0xFF); + *ecc_code++ = ((bch_val1 >> 12) & 0xFF); + *ecc_code++ = ((bch_val1 >> 4) & 0xFF); + *ecc_code++ = ((bch_val1 & 0xF) << 4); + break; + case OMAP_ECC_BCH16_CODE_HW: + val = readl(gpmc_regs->gpmc_bch_result6[i]); + ecc_code[0] = ((val >> 8) & 0xFF); + ecc_code[1] = ((val >> 0) & 0xFF); + val = readl(gpmc_regs->gpmc_bch_result5[i]); + ecc_code[2] = ((val >> 24) & 0xFF); + ecc_code[3] = ((val >> 16) & 0xFF); + ecc_code[4] = ((val >> 8) & 0xFF); + ecc_code[5] = ((val >> 0) & 0xFF); + val = readl(gpmc_regs->gpmc_bch_result4[i]); + ecc_code[6] = ((val >> 24) & 0xFF); + ecc_code[7] = ((val >> 16) & 0xFF); + ecc_code[8] = ((val >> 8) & 0xFF); + ecc_code[9] = ((val >> 0) & 0xFF); + val = readl(gpmc_regs->gpmc_bch_result3[i]); + ecc_code[10] = ((val >> 24) & 0xFF); + ecc_code[11] = ((val >> 16) & 0xFF); + ecc_code[12] = ((val >> 8) & 0xFF); + ecc_code[13] = ((val >> 0) & 0xFF); + val = readl(gpmc_regs->gpmc_bch_result2[i]); + ecc_code[14] = ((val >> 24) & 0xFF); + ecc_code[15] = ((val >> 16) & 0xFF); + ecc_code[16] = ((val >> 8) & 0xFF); + ecc_code[17] = ((val >> 0) & 0xFF); + val = readl(gpmc_regs->gpmc_bch_result1[i]); + ecc_code[18] = ((val >> 24) & 0xFF); + ecc_code[19] = ((val >> 16) & 0xFF); + ecc_code[20] = ((val >> 8) & 0xFF); + ecc_code[21] = ((val >> 0) & 0xFF); + val = readl(gpmc_regs->gpmc_bch_result0[i]); + ecc_code[22] = ((val >> 24) & 0xFF); + ecc_code[23] = ((val >> 16) & 0xFF); + ecc_code[24] = ((val >> 8) & 0xFF); + ecc_code[25] = ((val >> 0) & 0xFF); + break; + default: + return -EINVAL; + } - /* Read hw-computed remainder */ - val1 = readl(info->reg.gpmc_bch_result0[i]); - val2 = readl(info->reg.gpmc_bch_result1[i]); + /* ECC scheme specific syndrome customizations */ + switch (info->ecc_opt) { + case OMAP_ECC_BCH4_CODE_HW_DETECTION_SW: + /* Add constant polynomial to remainder, so that + * ECC of blank pages results in 0x0 on reading back */ + for (j = 0; j < eccbytes; j++) + ecc_calc[j] ^= bch4_polynomial[j]; + break; + case OMAP_ECC_BCH4_CODE_HW: + /* Set 8th ECC byte as 0x0 for ROM compatibility */ + ecc_calc[eccbytes - 1] = 0x0; + break; + case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW: + /* Add constant polynomial to remainder, so that + * ECC of blank pages results in 0x0 on reading back */ + for (j = 0; j < eccbytes; j++) + ecc_calc[j] ^= bch8_polynomial[j]; + break; + case OMAP_ECC_BCH8_CODE_HW: + /* Set 14th ECC byte as 0x0 for ROM compatibility */ + ecc_calc[eccbytes - 1] = 0x0; + break; + case OMAP_ECC_BCH16_CODE_HW: + break; + default: + return -EINVAL; + } - /* - * Add constant polynomial to remainder, in order to get an ecc - * sequence of 0xFFs for a buffer filled with 0xFFs; and - * left-justify the resulting polynomial. - */ - *ecc_code++ = 0x28 ^ ((val2 >> 12) & 0xFF); - *ecc_code++ = 0x13 ^ ((val2 >> 4) & 0xFF); - *ecc_code++ = 0xcc ^ (((val2 & 0xF) << 4)|((val1 >> 28) & 0xF)); - *ecc_code++ = 0x39 ^ ((val1 >> 20) & 0xFF); - *ecc_code++ = 0x96 ^ ((val1 >> 12) & 0xFF); - *ecc_code++ = 0xac ^ ((val1 >> 4) & 0xFF); - *ecc_code++ = 0x7f ^ ((val1 & 0xF) << 4); + ecc_calc += eccbytes; } return 0; } +#ifdef CONFIG_MTD_NAND_OMAP_BCH /** - * omap3_calculate_ecc_bch8 - Generate 13 bytes of ECC bytes - * @mtd: MTD device structure - * @dat: The pointer to data on which ecc is computed - * @ecc_code: The ecc_code buffer + * erased_sector_bitflips - count bit flips + * @data: data sector buffer + * @oob: oob buffer + * @info: omap_nand_info + * + * Check the bit flips in erased page falls below correctable level. + * If falls below, report the page as erased with correctable bit + * flip, else report as uncorrectable page. */ -static int omap3_calculate_ecc_bch8(struct mtd_info *mtd, const u_char *dat, - u_char *ecc_code) +static int erased_sector_bitflips(u_char *data, u_char *oob, + struct omap_nand_info *info) { - struct omap_nand_info *info = container_of(mtd, struct omap_nand_info, - mtd); - unsigned long nsectors, val1, val2, val3, val4; - int i; + int flip_bits = 0, i; - nsectors = ((readl(info->reg.gpmc_ecc_config) >> 4) & 0x7) + 1; - - for (i = 0; i < nsectors; i++) { + for (i = 0; i < info->nand.ecc.size; i++) { + flip_bits += hweight8(~data[i]); + if (flip_bits > info->nand.ecc.strength) + return 0; + } - /* Read hw-computed remainder */ - val1 = readl(info->reg.gpmc_bch_result0[i]); - val2 = readl(info->reg.gpmc_bch_result1[i]); - val3 = readl(info->reg.gpmc_bch_result2[i]); - val4 = readl(info->reg.gpmc_bch_result3[i]); + for (i = 0; i < info->nand.ecc.bytes - 1; i++) { + flip_bits += hweight8(~oob[i]); + if (flip_bits > info->nand.ecc.strength) + return 0; + } - /* - * Add constant polynomial to remainder, in order to get an ecc - * sequence of 0xFFs for a buffer filled with 0xFFs. - */ - *ecc_code++ = 0xef ^ (val4 & 0xFF); - *ecc_code++ = 0x51 ^ ((val3 >> 24) & 0xFF); - *ecc_code++ = 0x2e ^ ((val3 >> 16) & 0xFF); - *ecc_code++ = 0x09 ^ ((val3 >> 8) & 0xFF); - *ecc_code++ = 0xed ^ (val3 & 0xFF); - *ecc_code++ = 0x93 ^ ((val2 >> 24) & 0xFF); - *ecc_code++ = 0x9a ^ ((val2 >> 16) & 0xFF); - *ecc_code++ = 0xc2 ^ ((val2 >> 8) & 0xFF); - *ecc_code++ = 0x97 ^ (val2 & 0xFF); - *ecc_code++ = 0x79 ^ ((val1 >> 24) & 0xFF); - *ecc_code++ = 0xe5 ^ ((val1 >> 16) & 0xFF); - *ecc_code++ = 0x24 ^ ((val1 >> 8) & 0xFF); - *ecc_code++ = 0xb5 ^ (val1 & 0xFF); + /* + * Bit flips falls in correctable level. + * Fill data area with 0xFF + */ + if (flip_bits) { + memset(data, 0xFF, info->nand.ecc.size); + memset(oob, 0xFF, info->nand.ecc.bytes); } - return 0; + return flip_bits; } /** - * omap3_correct_data_bch - Decode received data and correct errors - * @mtd: MTD device structure - * @data: page data - * @read_ecc: ecc read from nand flash - * @calc_ecc: ecc read from HW ECC registers + * omap_elm_correct_data - corrects page data area in case error reported + * @mtd: MTD device structure + * @data: page data + * @read_ecc: ecc read from nand flash + * @calc_ecc: ecc read from HW ECC registers + * + * Calculated ecc vector reported as zero in case of non-error pages. + * In case of non-zero ecc vector, first filter out erased-pages, and + * then process data via ELM to detect bit-flips. */ -static int omap3_correct_data_bch(struct mtd_info *mtd, u_char *data, - u_char *read_ecc, u_char *calc_ecc) +static int omap_elm_correct_data(struct mtd_info *mtd, u_char *data, + u_char *read_ecc, u_char *calc_ecc) { - int i, count; - /* cannot correct more than 8 errors */ - unsigned int errloc[8]; struct omap_nand_info *info = container_of(mtd, struct omap_nand_info, - mtd); + mtd); + struct nand_ecc_ctrl *ecc = &info->nand.ecc; + int eccsteps = info->nand.ecc.steps; + int i , j, stat = 0; + int eccflag, actual_eccbytes; + struct elm_errorvec err_vec[ERROR_VECTOR_MAX]; + u_char *ecc_vec = calc_ecc; + u_char *spare_ecc = read_ecc; + u_char *erased_ecc_vec; + u_char *buf; + int bitflip_count; + bool is_error_reported = false; + u32 bit_pos, byte_pos, error_max, pos; + int err; + + switch (info->ecc_opt) { + case OMAP_ECC_BCH4_CODE_HW: + /* omit 7th ECC byte reserved for ROM code compatibility */ + actual_eccbytes = ecc->bytes - 1; + erased_ecc_vec = bch4_vector; + break; + case OMAP_ECC_BCH8_CODE_HW: + /* omit 14th ECC byte reserved for ROM code compatibility */ + actual_eccbytes = ecc->bytes - 1; + erased_ecc_vec = bch8_vector; + break; + case OMAP_ECC_BCH16_CODE_HW: + actual_eccbytes = ecc->bytes; + erased_ecc_vec = bch16_vector; + break; + default: + pr_err("invalid driver configuration\n"); + return -EINVAL; + } + + /* Initialize elm error vector to zero */ + memset(err_vec, 0, sizeof(err_vec)); + + for (i = 0; i < eccsteps ; i++) { + eccflag = 0; /* initialize eccflag */ - count = decode_bch(info->bch, NULL, 512, read_ecc, calc_ecc, NULL, - errloc); - if (count > 0) { - /* correct errors */ - for (i = 0; i < count; i++) { - /* correct data only, not ecc bytes */ - if (errloc[i] < 8*512) - data[errloc[i]/8] ^= 1 << (errloc[i] & 7); - pr_debug("corrected bitflip %u\n", errloc[i]); + /* + * Check any error reported, + * In case of error, non zero ecc reported. + */ + for (j = 0; j < actual_eccbytes; j++) { + if (calc_ecc[j] != 0) { + eccflag = 1; /* non zero ecc, error present */ + break; + } } - } else if (count < 0) { - pr_err("ecc unrecoverable error\n"); + + if (eccflag == 1) { + if (memcmp(calc_ecc, erased_ecc_vec, + actual_eccbytes) == 0) { + /* + * calc_ecc[] matches pattern for ECC(all 0xff) + * so this is definitely an erased-page + */ + } else { + buf = &data[info->nand.ecc.size * i]; + /* + * count number of 0-bits in read_buf. + * This check can be removed once a similar + * check is introduced in generic NAND driver + */ + bitflip_count = erased_sector_bitflips( + buf, read_ecc, info); + if (bitflip_count) { + /* + * number of 0-bits within ECC limits + * So this may be an erased-page + */ + stat += bitflip_count; + } else { + /* + * Too many 0-bits. It may be a + * - programmed-page, OR + * - erased-page with many bit-flips + * So this page requires check by ELM + */ + err_vec[i].error_reported = true; + is_error_reported = true; + } + } + } + + /* Update the ecc vector */ + calc_ecc += ecc->bytes; + read_ecc += ecc->bytes; } - return count; -} -/** - * omap3_free_bch - Release BCH ecc resources - * @mtd: MTD device structure - */ -static void omap3_free_bch(struct mtd_info *mtd) -{ - struct omap_nand_info *info = container_of(mtd, struct omap_nand_info, - mtd); - if (info->bch) { - free_bch(info->bch); - info->bch = NULL; + /* Check if any error reported */ + if (!is_error_reported) + return stat; + + /* Decode BCH error using ELM module */ + elm_decode_bch_error_page(info->elm_dev, ecc_vec, err_vec); + + err = 0; + for (i = 0; i < eccsteps; i++) { + if (err_vec[i].error_uncorrectable) { + pr_err("nand: uncorrectable bit-flips found\n"); + err = -EBADMSG; + } else if (err_vec[i].error_reported) { + for (j = 0; j < err_vec[i].error_count; j++) { + switch (info->ecc_opt) { + case OMAP_ECC_BCH4_CODE_HW: + /* Add 4 bits to take care of padding */ + pos = err_vec[i].error_loc[j] + + BCH4_BIT_PAD; + break; + case OMAP_ECC_BCH8_CODE_HW: + case OMAP_ECC_BCH16_CODE_HW: + pos = err_vec[i].error_loc[j]; + break; + default: + return -EINVAL; + } + error_max = (ecc->size + actual_eccbytes) * 8; + /* Calculate bit position of error */ + bit_pos = pos % 8; + + /* Calculate byte position of error */ + byte_pos = (error_max - pos - 1) / 8; + + if (pos < error_max) { + if (byte_pos < 512) { + pr_debug("bitflip@dat[%d]=%x\n", + byte_pos, data[byte_pos]); + data[byte_pos] ^= 1 << bit_pos; + } else { + pr_debug("bitflip@oob[%d]=%x\n", + (byte_pos - 512), + spare_ecc[byte_pos - 512]); + spare_ecc[byte_pos - 512] ^= + 1 << bit_pos; + } + } else { + pr_err("invalid bit-flip @ %d:%d\n", + byte_pos, bit_pos); + err = -EBADMSG; + } + } + } + + /* Update number of correctable errors */ + stat += err_vec[i].error_count; + + /* Update page data with sector size */ + data += ecc->size; + spare_ecc += ecc->bytes; } + + return (err) ? err : stat; } /** - * omap3_init_bch - Initialize BCH ECC - * @mtd: MTD device structure - * @ecc_opt: OMAP ECC mode (OMAP_ECC_BCH4_CODE_HW or OMAP_ECC_BCH8_CODE_HW) + * omap_write_page_bch - BCH ecc based write page function for entire page + * @mtd: mtd info structure + * @chip: nand chip info structure + * @buf: data buffer + * @oob_required: must write chip->oob_poi to OOB + * + * Custom write page method evolved to support multi sector writing in one shot */ -static int omap3_init_bch(struct mtd_info *mtd, int ecc_opt) +static int omap_write_page_bch(struct mtd_info *mtd, struct nand_chip *chip, + const uint8_t *buf, int oob_required) { - int max_errors; - struct omap_nand_info *info = container_of(mtd, struct omap_nand_info, - mtd); -#ifdef CONFIG_MTD_NAND_OMAP_BCH8 - const int hw_errors = 8; -#else - const int hw_errors = 4; -#endif - info->bch = NULL; - - max_errors = (ecc_opt == OMAP_ECC_BCH8_CODE_HW) ? 8 : 4; - if (max_errors != hw_errors) { - pr_err("cannot configure %d-bit BCH ecc, only %d-bit supported", - max_errors, hw_errors); - goto fail; - } + int i; + uint8_t *ecc_calc = chip->buffers->ecccalc; + uint32_t *eccpos = chip->ecc.layout->eccpos; - /* software bch library is only used to detect and locate errors */ - info->bch = init_bch(13, max_errors, 0x201b /* hw polynomial */); - if (!info->bch) - goto fail; + /* Enable GPMC ecc engine */ + chip->ecc.hwctl(mtd, NAND_ECC_WRITE); - info->nand.ecc.size = 512; - info->nand.ecc.hwctl = omap3_enable_hwecc_bch; - info->nand.ecc.correct = omap3_correct_data_bch; - info->nand.ecc.mode = NAND_ECC_HW; + /* Write data */ + chip->write_buf(mtd, buf, mtd->writesize); - /* - * The number of corrected errors in an ecc block that will trigger - * block scrubbing defaults to the ecc strength (4 or 8). - * Set mtd->bitflip_threshold here to define a custom threshold. - */ + /* Update ecc vector from GPMC result registers */ + chip->ecc.calculate(mtd, buf, &ecc_calc[0]); - if (max_errors == 8) { - info->nand.ecc.strength = 8; - info->nand.ecc.bytes = 13; - info->nand.ecc.calculate = omap3_calculate_ecc_bch8; - } else { - info->nand.ecc.strength = 4; - info->nand.ecc.bytes = 7; - info->nand.ecc.calculate = omap3_calculate_ecc_bch4; - } + for (i = 0; i < chip->ecc.total; i++) + chip->oob_poi[eccpos[i]] = ecc_calc[i]; - pr_info("enabling NAND BCH ecc with %d-bit correction\n", max_errors); + /* Write ecc vector to OOB area */ + chip->write_buf(mtd, chip->oob_poi, mtd->oobsize); return 0; -fail: - omap3_free_bch(mtd); - return -1; } /** - * omap3_init_bch_tail - Build an oob layout for BCH ECC correction. - * @mtd: MTD device structure + * omap_read_page_bch - BCH ecc based page read function for entire page + * @mtd: mtd info structure + * @chip: nand chip info structure + * @buf: buffer to store read data + * @oob_required: caller requires OOB data read to chip->oob_poi + * @page: page number to read + * + * For BCH ecc scheme, GPMC used for syndrome calculation and ELM module + * used for error correction. + * Custom method evolved to support ELM error correction & multi sector + * reading. On reading page data area is read along with OOB data with + * ecc engine enabled. ecc vector updated after read of OOB data. + * For non error pages ecc vector reported as zero. */ -static int omap3_init_bch_tail(struct mtd_info *mtd) +static int omap_read_page_bch(struct mtd_info *mtd, struct nand_chip *chip, + uint8_t *buf, int oob_required, int page) { - int i, steps; - struct omap_nand_info *info = container_of(mtd, struct omap_nand_info, - mtd); - struct nand_ecclayout *layout = &info->ecclayout; + uint8_t *ecc_calc = chip->buffers->ecccalc; + uint8_t *ecc_code = chip->buffers->ecccode; + uint32_t *eccpos = chip->ecc.layout->eccpos; + uint8_t *oob = &chip->oob_poi[eccpos[0]]; + uint32_t oob_pos = mtd->writesize + chip->ecc.layout->eccpos[0]; + int stat; + unsigned int max_bitflips = 0; - /* build oob layout */ - steps = mtd->writesize/info->nand.ecc.size; - layout->eccbytes = steps*info->nand.ecc.bytes; + /* Enable GPMC ecc engine */ + chip->ecc.hwctl(mtd, NAND_ECC_READ); - /* do not bother creating special oob layouts for small page devices */ - if (mtd->oobsize < 64) { - pr_err("BCH ecc is not supported on small page devices\n"); - goto fail; - } + /* Read data */ + chip->read_buf(mtd, buf, mtd->writesize); - /* reserve 2 bytes for bad block marker */ - if (layout->eccbytes+2 > mtd->oobsize) { - pr_err("no oob layout available for oobsize %d eccbytes %u\n", - mtd->oobsize, layout->eccbytes); - goto fail; - } + /* Read oob bytes */ + chip->cmdfunc(mtd, NAND_CMD_RNDOUT, oob_pos, -1); + chip->read_buf(mtd, oob, chip->ecc.total); - /* put ecc bytes at oob tail */ - for (i = 0; i < layout->eccbytes; i++) - layout->eccpos[i] = mtd->oobsize-layout->eccbytes+i; + /* Calculate ecc bytes */ + chip->ecc.calculate(mtd, buf, ecc_calc); - layout->oobfree[0].offset = 2; - layout->oobfree[0].length = mtd->oobsize-2-layout->eccbytes; - info->nand.ecc.layout = layout; + memcpy(ecc_code, &chip->oob_poi[eccpos[0]], chip->ecc.total); - if (!(info->nand.options & NAND_BUSWIDTH_16)) - info->nand.badblock_pattern = &bb_descrip_flashbased; - return 0; -fail: - omap3_free_bch(mtd); - return -1; -} + stat = chip->ecc.correct(mtd, buf, ecc_code, ecc_calc); -#else -static int omap3_init_bch(struct mtd_info *mtd, int ecc_opt) -{ - pr_err("CONFIG_MTD_NAND_OMAP_BCH is not enabled\n"); - return -1; -} -static int omap3_init_bch_tail(struct mtd_info *mtd) -{ - return -1; + if (stat < 0) { + mtd->ecc_stats.failed++; + } else { + mtd->ecc_stats.corrected += stat; + max_bitflips = max_t(unsigned int, max_bitflips, stat); + } + + return max_bitflips; } -static void omap3_free_bch(struct mtd_info *mtd) + +/** + * is_elm_present - checks for presence of ELM module by scanning DT nodes + * @omap_nand_info: NAND device structure containing platform data + * @bch_type: 0x0=BCH4, 0x1=BCH8, 0x2=BCH16 + */ +static int is_elm_present(struct omap_nand_info *info, + struct device_node *elm_node, enum bch_ecc bch_type) { + struct platform_device *pdev; + struct nand_ecc_ctrl *ecc = &info->nand.ecc; + int err; + /* check whether elm-id is passed via DT */ + if (!elm_node) { + pr_err("nand: error: ELM DT node not found\n"); + return -ENODEV; + } + pdev = of_find_device_by_node(elm_node); + /* check whether ELM device is registered */ + if (!pdev) { + pr_err("nand: error: ELM device not found\n"); + return -ENODEV; + } + /* ELM module available, now configure it */ + info->elm_dev = &pdev->dev; + err = elm_config(info->elm_dev, bch_type, + (info->mtd.writesize / ecc->size), ecc->size, ecc->bytes); + + return err; } -#endif /* CONFIG_MTD_NAND_OMAP_BCH */ +#endif /* CONFIG_MTD_NAND_ECC_BCH */ static int omap_nand_probe(struct platform_device *pdev) { struct omap_nand_info *info; struct omap_nand_platform_data *pdata; + struct mtd_info *mtd; + struct nand_chip *nand_chip; + struct nand_ecclayout *ecclayout; int err; - int i, offset; - dma_cap_mask_t mask; - unsigned sig; + int i; + dma_cap_mask_t mask; + unsigned sig; + unsigned oob_index; struct resource *res; + struct mtd_part_parser_data ppdata = {}; - pdata = pdev->dev.platform_data; + pdata = dev_get_platdata(&pdev->dev); if (pdata == NULL) { dev_err(&pdev->dev, "platform data missing\n"); return -ENODEV; } - info = kzalloc(sizeof(struct omap_nand_info), GFP_KERNEL); + info = devm_kzalloc(&pdev->dev, sizeof(struct omap_nand_info), + GFP_KERNEL); if (!info) return -ENOMEM; @@ -1348,44 +1652,30 @@ static int omap_nand_probe(struct platform_device *pdev) spin_lock_init(&info->controller.lock); init_waitqueue_head(&info->controller.wq); - info->pdev = pdev; - + info->pdev = pdev; info->gpmc_cs = pdata->cs; info->reg = pdata->reg; - - info->mtd.priv = &info->nand; - info->mtd.name = dev_name(&pdev->dev); - info->mtd.owner = THIS_MODULE; - - info->nand.options = pdata->devsize; - info->nand.options |= NAND_SKIP_BBTSCAN; + info->of_node = pdata->of_node; + info->ecc_opt = pdata->ecc_opt; + mtd = &info->mtd; + mtd->priv = &info->nand; + mtd->name = dev_name(&pdev->dev); + mtd->owner = THIS_MODULE; + nand_chip = &info->nand; + nand_chip->ecc.priv = NULL; + nand_chip->options |= NAND_SKIP_BBTSCAN; res = platform_get_resource(pdev, IORESOURCE_MEM, 0); - if (res == NULL) { - err = -EINVAL; - dev_err(&pdev->dev, "error getting memory resource\n"); - goto out_free_info; - } + nand_chip->IO_ADDR_R = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(nand_chip->IO_ADDR_R)) + return PTR_ERR(nand_chip->IO_ADDR_R); info->phys_base = res->start; - info->mem_size = resource_size(res); - - if (!request_mem_region(info->phys_base, info->mem_size, - pdev->dev.driver->name)) { - err = -EBUSY; - goto out_free_info; - } - - info->nand.IO_ADDR_R = ioremap(info->phys_base, info->mem_size); - if (!info->nand.IO_ADDR_R) { - err = -ENOMEM; - goto out_release_mem_region; - } - info->nand.controller = &info->controller; + nand_chip->controller = &info->controller; - info->nand.IO_ADDR_W = info->nand.IO_ADDR_R; - info->nand.cmd_ctrl = omap_hwcontrol; + nand_chip->IO_ADDR_W = nand_chip->IO_ADDR_R; + nand_chip->cmd_ctrl = omap_hwcontrol; /* * If RDY/BSY line is connected to OMAP then use the omap ready @@ -1395,27 +1685,37 @@ static int omap_nand_probe(struct platform_device *pdev) * device and read status register until you get a failure or success */ if (pdata->dev_ready) { - info->nand.dev_ready = omap_dev_ready; - info->nand.chip_delay = 0; + nand_chip->dev_ready = omap_dev_ready; + nand_chip->chip_delay = 0; } else { - info->nand.waitfunc = omap_wait; - info->nand.chip_delay = 50; + nand_chip->waitfunc = omap_wait; + nand_chip->chip_delay = 50; } + /* scan NAND device connected to chip controller */ + nand_chip->options |= pdata->devsize & NAND_BUSWIDTH_16; + if (nand_scan_ident(mtd, 1, NULL)) { + pr_err("nand device scan failed, may be bus-width mismatch\n"); + err = -ENXIO; + goto return_error; + } + + /* check for small page devices */ + if ((mtd->oobsize < 64) && (pdata->ecc_opt != OMAP_ECC_HAM1_CODE_HW)) { + pr_err("small page devices are not supported\n"); + err = -EINVAL; + goto return_error; + } + + /* re-populate low-level callbacks based on xfer modes */ switch (pdata->xfer_type) { case NAND_OMAP_PREFETCH_POLLED: - info->nand.read_buf = omap_read_buf_pref; - info->nand.write_buf = omap_write_buf_pref; + nand_chip->read_buf = omap_read_buf_pref; + nand_chip->write_buf = omap_write_buf_pref; break; case NAND_OMAP_POLLED: - if (info->nand.options & NAND_BUSWIDTH_16) { - info->nand.read_buf = omap_read_buf16; - info->nand.write_buf = omap_write_buf16; - } else { - info->nand.read_buf = omap_read_buf8; - info->nand.write_buf = omap_write_buf8; - } + /* Use nand_base defaults for {read,write}_buf */ break; case NAND_OMAP_PREFETCH_DMA: @@ -1426,7 +1726,7 @@ static int omap_nand_probe(struct platform_device *pdev) if (!info->dma) { dev_err(&pdev->dev, "DMA engine request failed\n"); err = -ENXIO; - goto out_release_mem_region; + goto return_error; } else { struct dma_slave_config cfg; @@ -1441,10 +1741,10 @@ static int omap_nand_probe(struct platform_device *pdev) if (err) { dev_err(&pdev->dev, "DMA engine slave config failed: %d\n", err); - goto out_release_mem_region; + goto return_error; } - info->nand.read_buf = omap_read_buf_dma_pref; - info->nand.write_buf = omap_write_buf_dma_pref; + nand_chip->read_buf = omap_read_buf_dma_pref; + nand_chip->write_buf = omap_write_buf_dma_pref; } break; @@ -1453,34 +1753,36 @@ static int omap_nand_probe(struct platform_device *pdev) if (info->gpmc_irq_fifo <= 0) { dev_err(&pdev->dev, "error getting fifo irq\n"); err = -ENODEV; - goto out_release_mem_region; + goto return_error; } - err = request_irq(info->gpmc_irq_fifo, omap_nand_irq, - IRQF_SHARED, "gpmc-nand-fifo", info); + err = devm_request_irq(&pdev->dev, info->gpmc_irq_fifo, + omap_nand_irq, IRQF_SHARED, + "gpmc-nand-fifo", info); if (err) { dev_err(&pdev->dev, "requesting irq(%d) error:%d", info->gpmc_irq_fifo, err); info->gpmc_irq_fifo = 0; - goto out_release_mem_region; + goto return_error; } info->gpmc_irq_count = platform_get_irq(pdev, 1); if (info->gpmc_irq_count <= 0) { dev_err(&pdev->dev, "error getting count irq\n"); err = -ENODEV; - goto out_release_mem_region; + goto return_error; } - err = request_irq(info->gpmc_irq_count, omap_nand_irq, - IRQF_SHARED, "gpmc-nand-count", info); + err = devm_request_irq(&pdev->dev, info->gpmc_irq_count, + omap_nand_irq, IRQF_SHARED, + "gpmc-nand-count", info); if (err) { dev_err(&pdev->dev, "requesting irq(%d) error:%d", info->gpmc_irq_count, err); info->gpmc_irq_count = 0; - goto out_release_mem_region; + goto return_error; } - info->nand.read_buf = omap_read_buf_irq_pref; - info->nand.write_buf = omap_write_buf_irq_pref; + nand_chip->read_buf = omap_read_buf_irq_pref; + nand_chip->write_buf = omap_write_buf_irq_pref; break; @@ -1488,117 +1790,275 @@ static int omap_nand_probe(struct platform_device *pdev) dev_err(&pdev->dev, "xfer_type(%d) not supported!\n", pdata->xfer_type); err = -EINVAL; - goto out_release_mem_region; + goto return_error; } - /* select the ecc type */ - if (pdata->ecc_opt == OMAP_ECC_HAMMING_CODE_DEFAULT) - info->nand.ecc.mode = NAND_ECC_SOFT; - else if ((pdata->ecc_opt == OMAP_ECC_HAMMING_CODE_HW) || - (pdata->ecc_opt == OMAP_ECC_HAMMING_CODE_HW_ROMCODE)) { - info->nand.ecc.bytes = 3; - info->nand.ecc.size = 512; - info->nand.ecc.strength = 1; - info->nand.ecc.calculate = omap_calculate_ecc; - info->nand.ecc.hwctl = omap_enable_hwecc; - info->nand.ecc.correct = omap_correct_data; - info->nand.ecc.mode = NAND_ECC_HW; - } else if ((pdata->ecc_opt == OMAP_ECC_BCH4_CODE_HW) || - (pdata->ecc_opt == OMAP_ECC_BCH8_CODE_HW)) { - err = omap3_init_bch(&info->mtd, pdata->ecc_opt); - if (err) { + /* populate MTD interface based on ECC scheme */ + nand_chip->ecc.layout = &omap_oobinfo; + ecclayout = &omap_oobinfo; + switch (info->ecc_opt) { + case OMAP_ECC_HAM1_CODE_HW: + pr_info("nand: using OMAP_ECC_HAM1_CODE_HW\n"); + nand_chip->ecc.mode = NAND_ECC_HW; + nand_chip->ecc.bytes = 3; + nand_chip->ecc.size = 512; + nand_chip->ecc.strength = 1; + nand_chip->ecc.calculate = omap_calculate_ecc; + nand_chip->ecc.hwctl = omap_enable_hwecc; + nand_chip->ecc.correct = omap_correct_data; + /* define ECC layout */ + ecclayout->eccbytes = nand_chip->ecc.bytes * + (mtd->writesize / + nand_chip->ecc.size); + if (nand_chip->options & NAND_BUSWIDTH_16) + oob_index = BADBLOCK_MARKER_LENGTH; + else + oob_index = 1; + for (i = 0; i < ecclayout->eccbytes; i++, oob_index++) + ecclayout->eccpos[i] = oob_index; + /* no reserved-marker in ecclayout for this ecc-scheme */ + ecclayout->oobfree->offset = + ecclayout->eccpos[ecclayout->eccbytes - 1] + 1; + break; + + case OMAP_ECC_BCH4_CODE_HW_DETECTION_SW: +#ifdef CONFIG_MTD_NAND_ECC_BCH + pr_info("nand: using OMAP_ECC_BCH4_CODE_HW_DETECTION_SW\n"); + nand_chip->ecc.mode = NAND_ECC_HW; + nand_chip->ecc.size = 512; + nand_chip->ecc.bytes = 7; + nand_chip->ecc.strength = 4; + nand_chip->ecc.hwctl = omap_enable_hwecc_bch; + nand_chip->ecc.correct = nand_bch_correct_data; + nand_chip->ecc.calculate = omap_calculate_ecc_bch; + /* define ECC layout */ + ecclayout->eccbytes = nand_chip->ecc.bytes * + (mtd->writesize / + nand_chip->ecc.size); + oob_index = BADBLOCK_MARKER_LENGTH; + for (i = 0; i < ecclayout->eccbytes; i++, oob_index++) { + ecclayout->eccpos[i] = oob_index; + if (((i + 1) % nand_chip->ecc.bytes) == 0) + oob_index++; + } + /* include reserved-marker in ecclayout->oobfree calculation */ + ecclayout->oobfree->offset = 1 + + ecclayout->eccpos[ecclayout->eccbytes - 1] + 1; + /* software bch library is used for locating errors */ + nand_chip->ecc.priv = nand_bch_init(mtd, + nand_chip->ecc.size, + nand_chip->ecc.bytes, + &nand_chip->ecc.layout); + if (!nand_chip->ecc.priv) { + pr_err("nand: error: unable to use s/w BCH library\n"); err = -EINVAL; - goto out_release_mem_region; } - } + break; +#else + pr_err("nand: error: CONFIG_MTD_NAND_ECC_BCH not enabled\n"); + err = -EINVAL; + goto return_error; +#endif - /* DIP switches on some boards change between 8 and 16 bit - * bus widths for flash. Try the other width if the first try fails. - */ - if (nand_scan_ident(&info->mtd, 1, NULL)) { - info->nand.options ^= NAND_BUSWIDTH_16; - if (nand_scan_ident(&info->mtd, 1, NULL)) { - err = -ENXIO; - goto out_release_mem_region; + case OMAP_ECC_BCH4_CODE_HW: +#ifdef CONFIG_MTD_NAND_OMAP_BCH + pr_info("nand: using OMAP_ECC_BCH4_CODE_HW ECC scheme\n"); + nand_chip->ecc.mode = NAND_ECC_HW; + nand_chip->ecc.size = 512; + /* 14th bit is kept reserved for ROM-code compatibility */ + nand_chip->ecc.bytes = 7 + 1; + nand_chip->ecc.strength = 4; + nand_chip->ecc.hwctl = omap_enable_hwecc_bch; + nand_chip->ecc.correct = omap_elm_correct_data; + nand_chip->ecc.calculate = omap_calculate_ecc_bch; + nand_chip->ecc.read_page = omap_read_page_bch; + nand_chip->ecc.write_page = omap_write_page_bch; + /* define ECC layout */ + ecclayout->eccbytes = nand_chip->ecc.bytes * + (mtd->writesize / + nand_chip->ecc.size); + oob_index = BADBLOCK_MARKER_LENGTH; + for (i = 0; i < ecclayout->eccbytes; i++, oob_index++) + ecclayout->eccpos[i] = oob_index; + /* reserved marker already included in ecclayout->eccbytes */ + ecclayout->oobfree->offset = + ecclayout->eccpos[ecclayout->eccbytes - 1] + 1; + /* This ECC scheme requires ELM H/W block */ + if (is_elm_present(info, pdata->elm_of_node, BCH4_ECC) < 0) { + pr_err("nand: error: could not initialize ELM\n"); + err = -ENODEV; + goto return_error; } - } - - /* rom code layout */ - if (pdata->ecc_opt == OMAP_ECC_HAMMING_CODE_HW_ROMCODE) { + break; +#else + pr_err("nand: error: CONFIG_MTD_NAND_OMAP_BCH not enabled\n"); + err = -EINVAL; + goto return_error; +#endif - if (info->nand.options & NAND_BUSWIDTH_16) - offset = 2; - else { - offset = 1; - info->nand.badblock_pattern = &bb_descrip_flashbased; + case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW: +#ifdef CONFIG_MTD_NAND_ECC_BCH + pr_info("nand: using OMAP_ECC_BCH8_CODE_HW_DETECTION_SW\n"); + nand_chip->ecc.mode = NAND_ECC_HW; + nand_chip->ecc.size = 512; + nand_chip->ecc.bytes = 13; + nand_chip->ecc.strength = 8; + nand_chip->ecc.hwctl = omap_enable_hwecc_bch; + nand_chip->ecc.correct = nand_bch_correct_data; + nand_chip->ecc.calculate = omap_calculate_ecc_bch; + /* define ECC layout */ + ecclayout->eccbytes = nand_chip->ecc.bytes * + (mtd->writesize / + nand_chip->ecc.size); + oob_index = BADBLOCK_MARKER_LENGTH; + for (i = 0; i < ecclayout->eccbytes; i++, oob_index++) { + ecclayout->eccpos[i] = oob_index; + if (((i + 1) % nand_chip->ecc.bytes) == 0) + oob_index++; } - omap_oobinfo.eccbytes = 3 * (info->mtd.oobsize/16); - for (i = 0; i < omap_oobinfo.eccbytes; i++) - omap_oobinfo.eccpos[i] = i+offset; - - omap_oobinfo.oobfree->offset = offset + omap_oobinfo.eccbytes; - omap_oobinfo.oobfree->length = info->mtd.oobsize - - (offset + omap_oobinfo.eccbytes); - - info->nand.ecc.layout = &omap_oobinfo; - } else if ((pdata->ecc_opt == OMAP_ECC_BCH4_CODE_HW) || - (pdata->ecc_opt == OMAP_ECC_BCH8_CODE_HW)) { - /* build OOB layout for BCH ECC correction */ - err = omap3_init_bch_tail(&info->mtd); - if (err) { + /* include reserved-marker in ecclayout->oobfree calculation */ + ecclayout->oobfree->offset = 1 + + ecclayout->eccpos[ecclayout->eccbytes - 1] + 1; + /* software bch library is used for locating errors */ + nand_chip->ecc.priv = nand_bch_init(mtd, + nand_chip->ecc.size, + nand_chip->ecc.bytes, + &nand_chip->ecc.layout); + if (!nand_chip->ecc.priv) { + pr_err("nand: error: unable to use s/w BCH library\n"); err = -EINVAL; - goto out_release_mem_region; + goto return_error; } + break; +#else + pr_err("nand: error: CONFIG_MTD_NAND_ECC_BCH not enabled\n"); + err = -EINVAL; + goto return_error; +#endif + + case OMAP_ECC_BCH8_CODE_HW: +#ifdef CONFIG_MTD_NAND_OMAP_BCH + pr_info("nand: using OMAP_ECC_BCH8_CODE_HW ECC scheme\n"); + nand_chip->ecc.mode = NAND_ECC_HW; + nand_chip->ecc.size = 512; + /* 14th bit is kept reserved for ROM-code compatibility */ + nand_chip->ecc.bytes = 13 + 1; + nand_chip->ecc.strength = 8; + nand_chip->ecc.hwctl = omap_enable_hwecc_bch; + nand_chip->ecc.correct = omap_elm_correct_data; + nand_chip->ecc.calculate = omap_calculate_ecc_bch; + nand_chip->ecc.read_page = omap_read_page_bch; + nand_chip->ecc.write_page = omap_write_page_bch; + /* This ECC scheme requires ELM H/W block */ + err = is_elm_present(info, pdata->elm_of_node, BCH8_ECC); + if (err < 0) { + pr_err("nand: error: could not initialize ELM\n"); + goto return_error; + } + /* define ECC layout */ + ecclayout->eccbytes = nand_chip->ecc.bytes * + (mtd->writesize / + nand_chip->ecc.size); + oob_index = BADBLOCK_MARKER_LENGTH; + for (i = 0; i < ecclayout->eccbytes; i++, oob_index++) + ecclayout->eccpos[i] = oob_index; + /* reserved marker already included in ecclayout->eccbytes */ + ecclayout->oobfree->offset = + ecclayout->eccpos[ecclayout->eccbytes - 1] + 1; + break; +#else + pr_err("nand: error: CONFIG_MTD_NAND_OMAP_BCH not enabled\n"); + err = -EINVAL; + goto return_error; +#endif + + case OMAP_ECC_BCH16_CODE_HW: +#ifdef CONFIG_MTD_NAND_OMAP_BCH + pr_info("using OMAP_ECC_BCH16_CODE_HW ECC scheme\n"); + nand_chip->ecc.mode = NAND_ECC_HW; + nand_chip->ecc.size = 512; + nand_chip->ecc.bytes = 26; + nand_chip->ecc.strength = 16; + nand_chip->ecc.hwctl = omap_enable_hwecc_bch; + nand_chip->ecc.correct = omap_elm_correct_data; + nand_chip->ecc.calculate = omap_calculate_ecc_bch; + nand_chip->ecc.read_page = omap_read_page_bch; + nand_chip->ecc.write_page = omap_write_page_bch; + /* This ECC scheme requires ELM H/W block */ + err = is_elm_present(info, pdata->elm_of_node, BCH16_ECC); + if (err < 0) { + pr_err("ELM is required for this ECC scheme\n"); + goto return_error; + } + /* define ECC layout */ + ecclayout->eccbytes = nand_chip->ecc.bytes * + (mtd->writesize / + nand_chip->ecc.size); + oob_index = BADBLOCK_MARKER_LENGTH; + for (i = 0; i < ecclayout->eccbytes; i++, oob_index++) + ecclayout->eccpos[i] = oob_index; + /* reserved marker already included in ecclayout->eccbytes */ + ecclayout->oobfree->offset = + ecclayout->eccpos[ecclayout->eccbytes - 1] + 1; + break; +#else + pr_err("nand: error: CONFIG_MTD_NAND_OMAP_BCH not enabled\n"); + err = -EINVAL; + goto return_error; +#endif + default: + pr_err("nand: error: invalid or unsupported ECC scheme\n"); + err = -EINVAL; + goto return_error; + } + + /* all OOB bytes from oobfree->offset till end off OOB are free */ + ecclayout->oobfree->length = mtd->oobsize - ecclayout->oobfree->offset; + /* check if NAND device's OOB is enough to store ECC signatures */ + if (mtd->oobsize < (ecclayout->eccbytes + BADBLOCK_MARKER_LENGTH)) { + pr_err("not enough OOB bytes required = %d, available=%d\n", + ecclayout->eccbytes, mtd->oobsize); + err = -EINVAL; + goto return_error; } /* second phase scan */ - if (nand_scan_tail(&info->mtd)) { + if (nand_scan_tail(mtd)) { err = -ENXIO; - goto out_release_mem_region; + goto return_error; } - mtd_device_parse_register(&info->mtd, NULL, NULL, pdata->parts, + ppdata.of_node = pdata->of_node; + mtd_device_parse_register(mtd, NULL, &ppdata, pdata->parts, pdata->nr_parts); - platform_set_drvdata(pdev, &info->mtd); + platform_set_drvdata(pdev, mtd); return 0; -out_release_mem_region: +return_error: if (info->dma) dma_release_channel(info->dma); - if (info->gpmc_irq_count > 0) - free_irq(info->gpmc_irq_count, info); - if (info->gpmc_irq_fifo > 0) - free_irq(info->gpmc_irq_fifo, info); - release_mem_region(info->phys_base, info->mem_size); -out_free_info: - kfree(info); - + if (nand_chip->ecc.priv) { + nand_bch_free(nand_chip->ecc.priv); + nand_chip->ecc.priv = NULL; + } return err; } static int omap_nand_remove(struct platform_device *pdev) { struct mtd_info *mtd = platform_get_drvdata(pdev); + struct nand_chip *nand_chip = mtd->priv; struct omap_nand_info *info = container_of(mtd, struct omap_nand_info, mtd); - omap3_free_bch(&info->mtd); - - platform_set_drvdata(pdev, NULL); + if (nand_chip->ecc.priv) { + nand_bch_free(nand_chip->ecc.priv); + nand_chip->ecc.priv = NULL; + } if (info->dma) dma_release_channel(info->dma); - - if (info->gpmc_irq_count > 0) - free_irq(info->gpmc_irq_count, info); - if (info->gpmc_irq_fifo > 0) - free_irq(info->gpmc_irq_fifo, info); - - /* Release NAND device, its internal structures and partitions */ - nand_release(&info->mtd); - iounmap(info->nand.IO_ADDR_R); - release_mem_region(info->phys_base, info->mem_size); - kfree(info); + nand_release(mtd); return 0; } |