diff options
Diffstat (limited to 'drivers/mtd/nand/nand_base.c')
| -rw-r--r-- | drivers/mtd/nand/nand_base.c | 450 |
1 files changed, 378 insertions, 72 deletions
diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c index bd39f7b6790..4f3e80c68a2 100644 --- a/drivers/mtd/nand/nand_base.c +++ b/drivers/mtd/nand/nand_base.c @@ -29,12 +29,15 @@ * */ +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + #include <linux/module.h> #include <linux/delay.h> #include <linux/errno.h> #include <linux/err.h> #include <linux/sched.h> #include <linux/slab.h> +#include <linux/mm.h> #include <linux/types.h> #include <linux/mtd/mtd.h> #include <linux/mtd/nand.h> @@ -202,6 +205,51 @@ static void nand_select_chip(struct mtd_info *mtd, int chipnr) } /** + * nand_write_byte - [DEFAULT] write single byte to chip + * @mtd: MTD device structure + * @byte: value to write + * + * Default function to write a byte to I/O[7:0] + */ +static void nand_write_byte(struct mtd_info *mtd, uint8_t byte) +{ + struct nand_chip *chip = mtd->priv; + + chip->write_buf(mtd, &byte, 1); +} + +/** + * nand_write_byte16 - [DEFAULT] write single byte to a chip with width 16 + * @mtd: MTD device structure + * @byte: value to write + * + * Default function to write a byte to I/O[7:0] on a 16-bit wide chip. + */ +static void nand_write_byte16(struct mtd_info *mtd, uint8_t byte) +{ + struct nand_chip *chip = mtd->priv; + uint16_t word = byte; + + /* + * It's not entirely clear what should happen to I/O[15:8] when writing + * a byte. The ONFi spec (Revision 3.1; 2012-09-19, Section 2.16) reads: + * + * When the host supports a 16-bit bus width, only data is + * transferred at the 16-bit width. All address and command line + * transfers shall use only the lower 8-bits of the data bus. During + * command transfers, the host may place any value on the upper + * 8-bits of the data bus. During address transfers, the host shall + * set the upper 8-bits of the data bus to 00h. + * + * One user of the write_byte callback is nand_onfi_set_features. The + * four parameters are specified to be written to I/O[7:0], but this is + * neither an address nor a command transfer. Let's assume a 0 on the + * upper I/O lines is OK. + */ + chip->write_buf(mtd, (uint8_t *)&word, 2); +} + +/** * nand_write_buf - [DEFAULT] write buffer to chip * @mtd: MTD device structure * @buf: data buffer @@ -542,7 +590,8 @@ static void nand_command(struct mtd_info *mtd, unsigned int command, /* Serially input address */ if (column != -1) { /* Adjust columns for 16 bit buswidth */ - if (chip->options & NAND_BUSWIDTH_16) + if (chip->options & NAND_BUSWIDTH_16 && + !nand_opcode_8bits(command)) column >>= 1; chip->cmd_ctrl(mtd, column, ctrl); ctrl &= ~NAND_CTRL_CHANGE; @@ -633,7 +682,8 @@ static void nand_command_lp(struct mtd_info *mtd, unsigned int command, /* Serially input address */ if (column != -1) { /* Adjust columns for 16 bit buswidth */ - if (chip->options & NAND_BUSWIDTH_16) + if (chip->options & NAND_BUSWIDTH_16 && + !nand_opcode_8bits(command)) column >>= 1; chip->cmd_ctrl(mtd, column, ctrl); ctrl &= ~NAND_CTRL_CHANGE; @@ -1113,9 +1163,11 @@ static int nand_read_page_swecc(struct mtd_info *mtd, struct nand_chip *chip, * @data_offs: offset of requested data within the page * @readlen: data length * @bufpoi: buffer to store read data + * @page: page number to read */ static int nand_read_subpage(struct mtd_info *mtd, struct nand_chip *chip, - uint32_t data_offs, uint32_t readlen, uint8_t *bufpoi) + uint32_t data_offs, uint32_t readlen, uint8_t *bufpoi, + int page) { int start_step, end_step, num_steps; uint32_t *eccpos = chip->ecc.layout->eccpos; @@ -1123,13 +1175,14 @@ static int nand_read_subpage(struct mtd_info *mtd, struct nand_chip *chip, int data_col_addr, i, gaps = 0; int datafrag_len, eccfrag_len, aligned_len, aligned_pos; int busw = (chip->options & NAND_BUSWIDTH_16) ? 2 : 1; - int index = 0; + int index; unsigned int max_bitflips = 0; /* Column address within the page aligned to ECC size (256bytes) */ start_step = data_offs / chip->ecc.size; end_step = (data_offs + readlen - 1) / chip->ecc.size; num_steps = end_step - start_step + 1; + index = start_step * chip->ecc.bytes; /* Data size aligned to ECC ecc.size */ datafrag_len = num_steps * chip->ecc.size; @@ -1152,8 +1205,7 @@ static int nand_read_subpage(struct mtd_info *mtd, struct nand_chip *chip, * ecc.pos. Let's make sure that there are no gaps in ECC positions. */ for (i = 0; i < eccfrag_len - 1; i++) { - if (eccpos[i + start_step * chip->ecc.bytes] + 1 != - eccpos[i + start_step * chip->ecc.bytes + 1]) { + if (eccpos[i + index] + 1 != eccpos[i + index + 1]) { gaps = 1; break; } @@ -1166,8 +1218,6 @@ static int nand_read_subpage(struct mtd_info *mtd, struct nand_chip *chip, * Send the command to read the particular ECC bytes take care * about buswidth alignment in read_buf. */ - index = start_step * chip->ecc.bytes; - aligned_pos = eccpos[index] & ~(busw - 1); aligned_len = eccfrag_len; if (eccpos[index] & (busw - 1)) @@ -1408,6 +1458,30 @@ static uint8_t *nand_transfer_oob(struct nand_chip *chip, uint8_t *oob, } /** + * nand_setup_read_retry - [INTERN] Set the READ RETRY mode + * @mtd: MTD device structure + * @retry_mode: the retry mode to use + * + * Some vendors supply a special command to shift the Vt threshold, to be used + * when there are too many bitflips in a page (i.e., ECC error). After setting + * a new threshold, the host should retry reading the page. + */ +static int nand_setup_read_retry(struct mtd_info *mtd, int retry_mode) +{ + struct nand_chip *chip = mtd->priv; + + pr_debug("setting READ RETRY mode %d\n", retry_mode); + + if (retry_mode >= chip->read_retries) + return -EINVAL; + + if (!chip->setup_read_retry) + return -EOPNOTSUPP; + + return chip->setup_read_retry(mtd, retry_mode); +} + +/** * nand_do_read_ops - [INTERN] Read data with ECC * @mtd: MTD device structure * @from: offset to read from @@ -1420,7 +1494,6 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from, { int chipnr, page, realpage, col, bytes, aligned, oob_required; struct nand_chip *chip = mtd->priv; - struct mtd_ecc_stats stats; int ret = 0; uint32_t readlen = ops->len; uint32_t oobreadlen = ops->ooblen; @@ -1428,9 +1501,10 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from, mtd->oobavail : mtd->oobsize; uint8_t *bufpoi, *oob, *buf; + int use_bufpoi; unsigned int max_bitflips = 0; - - stats = mtd->ecc_stats; + int retry_mode = 0; + bool ecc_fail = false; chipnr = (int)(from >> chip->chip_shift); chip->select_chip(mtd, chipnr); @@ -1445,13 +1519,27 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from, oob_required = oob ? 1 : 0; while (1) { + unsigned int ecc_failures = mtd->ecc_stats.failed; + bytes = min(mtd->writesize - col, readlen); aligned = (bytes == mtd->writesize); + if (!aligned) + use_bufpoi = 1; + else if (chip->options & NAND_USE_BOUNCE_BUFFER) + use_bufpoi = !virt_addr_valid(buf); + else + use_bufpoi = 0; + /* Is the current page in the buffer? */ if (realpage != chip->pagebuf || oob) { - bufpoi = aligned ? buf : chip->buffers->databuf; + bufpoi = use_bufpoi ? chip->buffers->databuf : buf; + + if (use_bufpoi && aligned) + pr_debug("%s: using read bounce buffer for buf@%p\n", + __func__, buf); +read_retry: chip->cmdfunc(mtd, NAND_CMD_READ0, 0x00, page); /* @@ -1465,12 +1553,13 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from, else if (!aligned && NAND_HAS_SUBPAGE_READ(chip) && !oob) ret = chip->ecc.read_subpage(mtd, chip, - col, bytes, bufpoi); + col, bytes, bufpoi, + page); else ret = chip->ecc.read_page(mtd, chip, bufpoi, oob_required, page); if (ret < 0) { - if (!aligned) + if (use_bufpoi) /* Invalidate page cache */ chip->pagebuf = -1; break; @@ -1479,9 +1568,9 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from, max_bitflips = max_t(unsigned int, max_bitflips, ret); /* Transfer not aligned data */ - if (!aligned) { + if (use_bufpoi) { if (!NAND_HAS_SUBPAGE_READ(chip) && !oob && - !(mtd->ecc_stats.failed - stats.failed) && + !(mtd->ecc_stats.failed - ecc_failures) && (ops->mode != MTD_OPS_RAW)) { chip->pagebuf = realpage; chip->pagebuf_bitflips = ret; @@ -1492,8 +1581,6 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from, memcpy(buf, chip->buffers->databuf + col, bytes); } - buf += bytes; - if (unlikely(oob)) { int toread = min(oobreadlen, max_oobsize); @@ -1511,6 +1598,25 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from, else nand_wait_ready(mtd); } + + if (mtd->ecc_stats.failed - ecc_failures) { + if (retry_mode + 1 < chip->read_retries) { + retry_mode++; + ret = nand_setup_read_retry(mtd, + retry_mode); + if (ret < 0) + break; + + /* Reset failures; retry */ + mtd->ecc_stats.failed = ecc_failures; + goto read_retry; + } else { + /* No more retry modes; real failure */ + ecc_fail = true; + } + } + + buf += bytes; } else { memcpy(buf, chip->buffers->databuf + col, bytes); buf += bytes; @@ -1520,6 +1626,14 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from, readlen -= bytes; + /* Reset to retry mode 0 */ + if (retry_mode) { + ret = nand_setup_read_retry(mtd, 0); + if (ret < 0) + break; + retry_mode = 0; + } + if (!readlen) break; @@ -1545,7 +1659,7 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from, if (ret < 0) return ret; - if (mtd->ecc_stats.failed - stats.failed) + if (ecc_fail) return -EBADMSG; return max_bitflips; @@ -1902,7 +2016,7 @@ static int nand_write_page_raw_syndrome(struct mtd_info *mtd, oob += chip->ecc.prepad; } - chip->read_buf(mtd, oob, eccbytes); + chip->write_buf(mtd, oob, eccbytes); oob += eccbytes; if (chip->ecc.postpad) { @@ -2274,11 +2388,23 @@ static int nand_do_write_ops(struct mtd_info *mtd, loff_t to, int bytes = mtd->writesize; int cached = writelen > bytes && page != blockmask; uint8_t *wbuf = buf; + int use_bufpoi; + int part_pagewr = (column || writelen < (mtd->writesize - 1)); + + if (part_pagewr) + use_bufpoi = 1; + else if (chip->options & NAND_USE_BOUNCE_BUFFER) + use_bufpoi = !virt_addr_valid(buf); + else + use_bufpoi = 0; - /* Partial page write? */ - if (unlikely(column || writelen < (mtd->writesize - 1))) { + /* Partial page write?, or need to use bounce buffer */ + if (use_bufpoi) { + pr_debug("%s: using write bounce buffer for buf@%p\n", + __func__, buf); cached = 0; - bytes = min_t(int, bytes - column, (int) writelen); + if (part_pagewr) + bytes = min_t(int, bytes - column, writelen); chip->pagebuf = -1; memset(chip->buffers->databuf, 0xff, mtd->writesize); memcpy(&chip->buffers->databuf[column], buf, bytes); @@ -2516,18 +2642,20 @@ out: } /** - * single_erase_cmd - [GENERIC] NAND standard block erase command function + * single_erase - [GENERIC] NAND standard block erase command function * @mtd: MTD device structure * @page: the page address of the block which will be erased * - * Standard erase command for NAND chips. + * Standard erase command for NAND chips. Returns NAND status. */ -static void single_erase_cmd(struct mtd_info *mtd, int page) +static int single_erase(struct mtd_info *mtd, int page) { struct nand_chip *chip = mtd->priv; /* Send commands to erase a block */ chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page); chip->cmdfunc(mtd, NAND_CMD_ERASE2, -1, -1); + + return chip->waitfunc(mtd, chip); } /** @@ -2608,9 +2736,7 @@ int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr, (page + pages_per_block)) chip->pagebuf = -1; - chip->erase_cmd(mtd, page & chip->pagemask); - - status = chip->waitfunc(mtd, chip); + status = chip->erase(mtd, page & chip->pagemask); /* * See if operation failed and additional status checks are @@ -2716,6 +2842,7 @@ static int nand_onfi_set_features(struct mtd_info *mtd, struct nand_chip *chip, int addr, uint8_t *subfeature_param) { int status; + int i; if (!chip->onfi_version || !(le16_to_cpu(chip->onfi_params.opt_cmd) @@ -2723,7 +2850,9 @@ static int nand_onfi_set_features(struct mtd_info *mtd, struct nand_chip *chip, return -EINVAL; chip->cmdfunc(mtd, NAND_CMD_SET_FEATURES, addr, -1); - chip->write_buf(mtd, subfeature_param, ONFI_SUBFEATURE_PARAM_LEN); + for (i = 0; i < ONFI_SUBFEATURE_PARAM_LEN; ++i) + chip->write_byte(mtd, subfeature_param[i]); + status = chip->waitfunc(mtd, chip); if (status & NAND_STATUS_FAIL) return -EIO; @@ -2740,6 +2869,8 @@ static int nand_onfi_set_features(struct mtd_info *mtd, struct nand_chip *chip, static int nand_onfi_get_features(struct mtd_info *mtd, struct nand_chip *chip, int addr, uint8_t *subfeature_param) { + int i; + if (!chip->onfi_version || !(le16_to_cpu(chip->onfi_params.opt_cmd) & ONFI_OPT_CMD_SET_GET_FEATURES)) @@ -2749,7 +2880,8 @@ static int nand_onfi_get_features(struct mtd_info *mtd, struct nand_chip *chip, memset(subfeature_param, 0, ONFI_SUBFEATURE_PARAM_LEN); chip->cmdfunc(mtd, NAND_CMD_GET_FEATURES, addr, -1); - chip->read_buf(mtd, subfeature_param, ONFI_SUBFEATURE_PARAM_LEN); + for (i = 0; i < ONFI_SUBFEATURE_PARAM_LEN; ++i) + *subfeature_param++ = chip->read_byte(mtd); return 0; } @@ -2812,6 +2944,8 @@ static void nand_set_defaults(struct nand_chip *chip, int busw) chip->block_markbad = nand_default_block_markbad; if (!chip->write_buf || chip->write_buf == nand_write_buf) chip->write_buf = busw ? nand_write_buf16 : nand_write_buf; + if (!chip->write_byte || chip->write_byte == nand_write_byte) + chip->write_byte = busw ? nand_write_byte16 : nand_write_byte; if (!chip->read_buf || chip->read_buf == nand_read_buf) chip->read_buf = busw ? nand_read_buf16 : nand_read_buf; if (!chip->scan_bbt) @@ -2926,6 +3060,30 @@ ext_out: return ret; } +static int nand_setup_read_retry_micron(struct mtd_info *mtd, int retry_mode) +{ + struct nand_chip *chip = mtd->priv; + uint8_t feature[ONFI_SUBFEATURE_PARAM_LEN] = {retry_mode}; + + return chip->onfi_set_features(mtd, chip, ONFI_FEATURE_ADDR_READ_RETRY, + feature); +} + +/* + * Configure chip properties from Micron vendor-specific ONFI table + */ +static void nand_onfi_detect_micron(struct nand_chip *chip, + struct nand_onfi_params *p) +{ + struct nand_onfi_vendor_micron *micron = (void *)p->vendor; + + if (le16_to_cpu(p->vendor_revision) < 1) + return; + + chip->read_retries = micron->read_retry_options; + chip->setup_read_retry = nand_setup_read_retry_micron; +} + /* * Check if the NAND chip is ONFI compliant, returns 1 if it is, 0 otherwise. */ @@ -2933,7 +3091,7 @@ static int nand_flash_detect_onfi(struct mtd_info *mtd, struct nand_chip *chip, int *busw) { struct nand_onfi_params *p = &chip->onfi_params; - int i; + int i, j; int val; /* Try ONFI for unknown chip or LP */ @@ -2942,18 +3100,10 @@ static int nand_flash_detect_onfi(struct mtd_info *mtd, struct nand_chip *chip, chip->read_byte(mtd) != 'F' || chip->read_byte(mtd) != 'I') return 0; - /* - * ONFI must be probed in 8-bit mode or with NAND_BUSWIDTH_AUTO, not - * with NAND_BUSWIDTH_16 - */ - if (chip->options & NAND_BUSWIDTH_16) { - pr_err("ONFI cannot be probed in 16-bit mode; aborting\n"); - return 0; - } - chip->cmdfunc(mtd, NAND_CMD_PARAM, 0, -1); for (i = 0; i < 3; i++) { - chip->read_buf(mtd, (uint8_t *)p, sizeof(*p)); + for (j = 0; j < sizeof(*p); j++) + ((uint8_t *)p)[j] = chip->read_byte(mtd); if (onfi_crc16(ONFI_CRC_BASE, (uint8_t *)p, 254) == le16_to_cpu(p->crc)) { break; @@ -2979,7 +3129,7 @@ static int nand_flash_detect_onfi(struct mtd_info *mtd, struct nand_chip *chip, chip->onfi_version = 10; if (!chip->onfi_version) { - pr_info("%s: unsupported ONFI version: %d\n", __func__, val); + pr_info("unsupported ONFI version: %d\n", val); return 0; } @@ -3032,6 +3182,90 @@ static int nand_flash_detect_onfi(struct mtd_info *mtd, struct nand_chip *chip, pr_warn("Could not retrieve ONFI ECC requirements\n"); } + if (p->jedec_id == NAND_MFR_MICRON) + nand_onfi_detect_micron(chip, p); + + return 1; +} + +/* + * Check if the NAND chip is JEDEC compliant, returns 1 if it is, 0 otherwise. + */ +static int nand_flash_detect_jedec(struct mtd_info *mtd, struct nand_chip *chip, + int *busw) +{ + struct nand_jedec_params *p = &chip->jedec_params; + struct jedec_ecc_info *ecc; + int val; + int i, j; + + /* Try JEDEC for unknown chip or LP */ + chip->cmdfunc(mtd, NAND_CMD_READID, 0x40, -1); + if (chip->read_byte(mtd) != 'J' || chip->read_byte(mtd) != 'E' || + chip->read_byte(mtd) != 'D' || chip->read_byte(mtd) != 'E' || + chip->read_byte(mtd) != 'C') + return 0; + + chip->cmdfunc(mtd, NAND_CMD_PARAM, 0x40, -1); + for (i = 0; i < 3; i++) { + for (j = 0; j < sizeof(*p); j++) + ((uint8_t *)p)[j] = chip->read_byte(mtd); + + if (onfi_crc16(ONFI_CRC_BASE, (uint8_t *)p, 510) == + le16_to_cpu(p->crc)) + break; + } + + if (i == 3) { + pr_err("Could not find valid JEDEC parameter page; aborting\n"); + return 0; + } + + /* Check version */ + val = le16_to_cpu(p->revision); + if (val & (1 << 2)) + chip->jedec_version = 10; + else if (val & (1 << 1)) + chip->jedec_version = 1; /* vendor specific version */ + + if (!chip->jedec_version) { + pr_info("unsupported JEDEC version: %d\n", val); + return 0; + } + + sanitize_string(p->manufacturer, sizeof(p->manufacturer)); + sanitize_string(p->model, sizeof(p->model)); + if (!mtd->name) + mtd->name = p->model; + + mtd->writesize = le32_to_cpu(p->byte_per_page); + + /* Please reference to the comment for nand_flash_detect_onfi. */ + mtd->erasesize = 1 << (fls(le32_to_cpu(p->pages_per_block)) - 1); + mtd->erasesize *= mtd->writesize; + + mtd->oobsize = le16_to_cpu(p->spare_bytes_per_page); + + /* Please reference to the comment for nand_flash_detect_onfi. */ + chip->chipsize = 1 << (fls(le32_to_cpu(p->blocks_per_lun)) - 1); + chip->chipsize *= (uint64_t)mtd->erasesize * p->lun_count; + chip->bits_per_cell = p->bits_per_cell; + + if (jedec_feature(chip) & JEDEC_FEATURE_16_BIT_BUS) + *busw = NAND_BUSWIDTH_16; + else + *busw = 0; + + /* ECC info */ + ecc = &p->ecc_info[0]; + + if (ecc->codeword_size >= 9) { + chip->ecc_strength_ds = ecc->ecc_bits; + chip->ecc_step_ds = 1 << ecc->codeword_size; + } else { + pr_warn("Invalid codeword size\n"); + } + return 1; } @@ -3152,9 +3386,12 @@ static void nand_decode_ext_id(struct mtd_info *mtd, struct nand_chip *chip, mtd->oobsize = 512; break; case 6: - default: /* Other cases are "reserved" (unknown) */ mtd->oobsize = 640; break; + case 7: + default: /* Other cases are "reserved" (unknown) */ + mtd->oobsize = 1024; + break; } extid >>= 2; /* Calc blocksize */ @@ -3325,6 +3562,9 @@ static bool find_full_id_nand(struct mtd_info *mtd, struct nand_chip *chip, *busw = type->options & NAND_BUSWIDTH_16; + if (!mtd->name) + mtd->name = type->name; + return true; } return false; @@ -3335,10 +3575,10 @@ static bool find_full_id_nand(struct mtd_info *mtd, struct nand_chip *chip, */ static struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd, struct nand_chip *chip, - int busw, int *maf_id, int *dev_id, struct nand_flash_dev *type) { + int busw; int i, maf_idx; u8 id_data[8]; @@ -3372,8 +3612,7 @@ static struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd, id_data[i] = chip->read_byte(mtd); if (id_data[0] != *maf_id || id_data[1] != *dev_id) { - pr_info("%s: second ID read did not match " - "%02x,%02x against %02x,%02x\n", __func__, + pr_info("second ID read did not match %02x,%02x against %02x,%02x\n", *maf_id, *dev_id, id_data[0], id_data[1]); return ERR_PTR(-ENODEV); } @@ -3392,9 +3631,13 @@ static struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd, chip->onfi_version = 0; if (!type->name || !type->pagesize) { - /* Check is chip is ONFI compliant */ + /* Check if the chip is ONFI compliant */ if (nand_flash_detect_onfi(mtd, chip, &busw)) goto ident_done; + + /* Check if the chip is JEDEC compliant */ + if (nand_flash_detect_jedec(mtd, chip, &busw)) + goto ident_done; } if (!type->name) @@ -3440,10 +3683,10 @@ ident_done: * Check, if buswidth is correct. Hardware drivers should set * chip correct! */ - pr_info("NAND device: Manufacturer ID:" - " 0x%02x, Chip ID: 0x%02x (%s %s)\n", *maf_id, - *dev_id, nand_manuf_ids[maf_idx].name, mtd->name); - pr_warn("NAND bus width %d instead %d bit\n", + pr_info("device found, Manufacturer ID: 0x%02x, Chip ID: 0x%02x\n", + *maf_id, *dev_id); + pr_info("%s %s\n", nand_manuf_ids[maf_idx].name, mtd->name); + pr_warn("bus width %d instead %d bit\n", (chip->options & NAND_BUSWIDTH_16) ? 16 : 8, busw ? 16 : 8); return ERR_PTR(-EINVAL); @@ -3466,20 +3709,28 @@ ident_done: } chip->badblockbits = 8; - chip->erase_cmd = single_erase_cmd; + chip->erase = single_erase; /* Do not replace user supplied command function! */ if (mtd->writesize > 512 && chip->cmdfunc == nand_command) chip->cmdfunc = nand_command_lp; - pr_info("NAND device: Manufacturer ID: 0x%02x, Chip ID: 0x%02x (%s %s)\n", - *maf_id, *dev_id, nand_manuf_ids[maf_idx].name, - chip->onfi_version ? chip->onfi_params.model : type->name); + pr_info("device found, Manufacturer ID: 0x%02x, Chip ID: 0x%02x\n", + *maf_id, *dev_id); + + if (chip->onfi_version) + pr_info("%s %s\n", nand_manuf_ids[maf_idx].name, + chip->onfi_params.model); + else if (chip->jedec_version) + pr_info("%s %s\n", nand_manuf_ids[maf_idx].name, + chip->jedec_params.model); + else + pr_info("%s %s\n", nand_manuf_ids[maf_idx].name, + type->name); - pr_info("NAND device: %dMiB, %s, page size: %d, OOB size: %d\n", + pr_info("%dMiB, %s, page size: %d, OOB size: %d\n", (int)(chip->chipsize >> 20), nand_is_slc(chip) ? "SLC" : "MLC", mtd->writesize, mtd->oobsize); - return type; } @@ -3497,18 +3748,16 @@ ident_done: int nand_scan_ident(struct mtd_info *mtd, int maxchips, struct nand_flash_dev *table) { - int i, busw, nand_maf_id, nand_dev_id; + int i, nand_maf_id, nand_dev_id; struct nand_chip *chip = mtd->priv; struct nand_flash_dev *type; - /* Get buswidth to select the correct functions */ - busw = chip->options & NAND_BUSWIDTH_16; /* Set the default functions */ - nand_set_defaults(chip, busw); + nand_set_defaults(chip, chip->options & NAND_BUSWIDTH_16); /* Read the flash type */ - type = nand_get_flash_type(mtd, chip, busw, - &nand_maf_id, &nand_dev_id, table); + type = nand_get_flash_type(mtd, chip, &nand_maf_id, + &nand_dev_id, table); if (IS_ERR(type)) { if (!(chip->options & NAND_SCAN_SILENT_NODEV)) @@ -3535,7 +3784,7 @@ int nand_scan_ident(struct mtd_info *mtd, int maxchips, chip->select_chip(mtd, -1); } if (i > 1) - pr_info("%d NAND chips detected\n", i); + pr_info("%d chips detected\n", i); /* Store the number of chips and calc total size for mtd */ chip->numchips = i; @@ -3545,6 +3794,39 @@ int nand_scan_ident(struct mtd_info *mtd, int maxchips, } EXPORT_SYMBOL(nand_scan_ident); +/* + * Check if the chip configuration meet the datasheet requirements. + + * If our configuration corrects A bits per B bytes and the minimum + * required correction level is X bits per Y bytes, then we must ensure + * both of the following are true: + * + * (1) A / B >= X / Y + * (2) A >= X + * + * Requirement (1) ensures we can correct for the required bitflip density. + * Requirement (2) ensures we can correct even when all bitflips are clumped + * in the same sector. + */ +static bool nand_ecc_strength_good(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + struct nand_ecc_ctrl *ecc = &chip->ecc; + int corr, ds_corr; + + if (ecc->size == 0 || chip->ecc_step_ds == 0) + /* Not enough information */ + return true; + + /* + * We get the number of corrected bits per page to compare + * the correction density. + */ + corr = (mtd->writesize * ecc->strength) / ecc->size; + ds_corr = (mtd->writesize * chip->ecc_strength_ds) / chip->ecc_step_ds; + + return corr >= ds_corr && ecc->strength >= chip->ecc_strength_ds; +} /** * nand_scan_tail - [NAND Interface] Scan for the NAND device @@ -3559,15 +3841,26 @@ int nand_scan_tail(struct mtd_info *mtd) int i; struct nand_chip *chip = mtd->priv; struct nand_ecc_ctrl *ecc = &chip->ecc; + struct nand_buffers *nbuf; /* New bad blocks should be marked in OOB, flash-based BBT, or both */ BUG_ON((chip->bbt_options & NAND_BBT_NO_OOB_BBM) && !(chip->bbt_options & NAND_BBT_USE_FLASH)); - if (!(chip->options & NAND_OWN_BUFFERS)) - chip->buffers = kmalloc(sizeof(*chip->buffers), GFP_KERNEL); - if (!chip->buffers) - return -ENOMEM; + if (!(chip->options & NAND_OWN_BUFFERS)) { + nbuf = kzalloc(sizeof(*nbuf) + mtd->writesize + + mtd->oobsize * 3, GFP_KERNEL); + if (!nbuf) + return -ENOMEM; + nbuf->ecccalc = (uint8_t *)(nbuf + 1); + nbuf->ecccode = nbuf->ecccalc + mtd->oobsize; + nbuf->databuf = nbuf->ecccode + mtd->oobsize; + + chip->buffers = nbuf; + } else { + if (!chip->buffers) + return -ENOMEM; + } /* Set the internal oob buffer location, just after the page data */ chip->oob_poi = chip->buffers->databuf + mtd->writesize; @@ -3688,7 +3981,7 @@ int nand_scan_tail(struct mtd_info *mtd) case NAND_ECC_SOFT_BCH: if (!mtd_nand_has_bch()) { - pr_warn("CONFIG_MTD_ECC_BCH not enabled\n"); + pr_warn("CONFIG_MTD_NAND_ECC_BCH not enabled\n"); BUG(); } ecc->calculate = nand_bch_calculate_ecc; @@ -3754,6 +4047,11 @@ int nand_scan_tail(struct mtd_info *mtd) ecc->layout->oobavail += ecc->layout->oobfree[i].length; mtd->oobavail = ecc->layout->oobavail; + /* ECC sanity check: warn if it's too weak */ + if (!nand_ecc_strength_good(mtd)) + pr_warn("WARNING: %s: the ECC used on your system is too weak compared to the one required by the NAND chip\n", + mtd->name); + /* * Set the number of read / write steps for one page depending on ECC * mode. @@ -3787,8 +4085,16 @@ int nand_scan_tail(struct mtd_info *mtd) chip->pagebuf = -1; /* Large page NAND with SOFT_ECC should support subpage reads */ - if ((ecc->mode == NAND_ECC_SOFT) && (chip->page_shift > 9)) - chip->options |= NAND_SUBPAGE_READ; + switch (ecc->mode) { + case NAND_ECC_SOFT: + case NAND_ECC_SOFT_BCH: + if (chip->page_shift > 9) + chip->options |= NAND_SUBPAGE_READ; + break; + + default: + break; + } /* Fill in remaining MTD driver data */ mtd->type = nand_is_slc(chip) ? MTD_NANDFLASH : MTD_MLCNANDFLASH; |