diff options
Diffstat (limited to 'drivers/mtd/nand/Kconfig')
| -rw-r--r-- | drivers/mtd/nand/Kconfig | 390 |
1 files changed, 238 insertions, 152 deletions
diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig index 8b12e6e109d..f1cf503517f 100644 --- a/drivers/mtd/nand/Kconfig +++ b/drivers/mtd/nand/Kconfig @@ -1,9 +1,20 @@ -# drivers/mtd/nand/Kconfig +config MTD_NAND_ECC + tristate + +config MTD_NAND_ECC_SMC + bool "NAND ECC Smart Media byte order" + depends on MTD_NAND_ECC + default n + help + Software ECC according to the Smart Media Specification. + The original Linux implementation had byte 0 and 1 swapped. + menuconfig MTD_NAND tristate "NAND Device Support" depends on MTD select MTD_NAND_IDS + select MTD_NAND_ECC help This enables support for accessing all type of NAND flash devices. For further information see @@ -11,88 +22,115 @@ menuconfig MTD_NAND if MTD_NAND -config MTD_NAND_VERIFY_WRITE - bool "Verify NAND page writes" - help - This adds an extra check when data is written to the flash. The - NAND flash device internally checks only bits transitioning - from 1 to 0. There is a rare possibility that even though the - device thinks the write was successful, a bit could have been - flipped accidentally due to device wear or something else. +config MTD_NAND_BCH + tristate + select BCH + depends on MTD_NAND_ECC_BCH + default MTD_NAND -config MTD_NAND_ECC_SMC - bool "NAND ECC Smart Media byte order" +config MTD_NAND_ECC_BCH + bool "Support software BCH ECC" default n help - Software ECC according to the Smart Media Specification. - The original Linux implementation had byte 0 and 1 swapped. + This enables support for software BCH error correction. Binary BCH + codes are more powerful and cpu intensive than traditional Hamming + ECC codes. They are used with NAND devices requiring more than 1 bit + of error correction. -config MTD_NAND_MUSEUM_IDS - bool "Enable chip ids for obsolete ancient NAND devices" - depends on MTD_NAND +config MTD_SM_COMMON + tristate default n - help - Enable this option only when your board has first generation - NAND chips (page size 256 byte, erase size 4-8KiB). The IDs - of these chips were reused by later, larger chips. -config MTD_NAND_AUTCPU12 - tristate "SmartMediaCard on autronix autcpu12 board" - depends on ARCH_AUTCPU12 - help - This enables the driver for the autronix autcpu12 board to - access the SmartMediaCard. +config MTD_NAND_DENALI + tristate "Support Denali NAND controller" + depends on HAS_DMA + help + Enable support for the Denali NAND controller. This should be + combined with either the PCI or platform drivers to provide device + registration. -config MTD_NAND_EDB7312 - tristate "Support for Cirrus Logic EBD7312 evaluation board" - depends on ARCH_EDB7312 - help - This enables the driver for the Cirrus Logic EBD7312 evaluation - board to access the onboard NAND Flash. +config MTD_NAND_DENALI_PCI + tristate "Support Denali NAND controller on Intel Moorestown" + depends on PCI && MTD_NAND_DENALI + help + Enable the driver for NAND flash on Intel Moorestown, using the + Denali NAND controller core. -config MTD_NAND_H1900 - tristate "iPAQ H1900 flash" - depends on ARCH_PXA && MTD_PARTITIONS +config MTD_NAND_DENALI_DT + tristate "Support Denali NAND controller as a DT device" + depends on HAVE_CLK && MTD_NAND_DENALI help - This enables the driver for the iPAQ h1900 flash. + Enable the driver for NAND flash on platforms using a Denali NAND + controller as a DT device. + +config MTD_NAND_DENALI_SCRATCH_REG_ADDR + hex "Denali NAND size scratch register address" + default "0xFF108018" + depends on MTD_NAND_DENALI_PCI + help + Some platforms place the NAND chip size in a scratch register + because (some versions of) the driver aren't able to automatically + determine the size of certain chips. Set the address of the + scratch register here to enable this feature. On Intel Moorestown + boards, the scratch register is at 0xFF108018. config MTD_NAND_GPIO tristate "GPIO NAND Flash driver" - depends on GENERIC_GPIO && ARM + depends on GPIOLIB help This enables a GPIO based NAND flash driver. -config MTD_NAND_SPIA - tristate "NAND Flash device on SPIA board" - depends on ARCH_P720T - help - If you had to ask, you don't have one. Say 'N'. - config MTD_NAND_AMS_DELTA tristate "NAND Flash device on Amstrad E3" depends on MACH_AMS_DELTA + default y help Support for NAND flash on Amstrad E3 (Delta). -config MTD_NAND_TS7250 - tristate "NAND Flash device on TS-7250 board" - depends on MACH_TS72XX +config MTD_NAND_OMAP2 + tristate "NAND Flash device on OMAP2, OMAP3 and OMAP4" + depends on ARCH_OMAP2PLUS help - Support for NAND flash on Technologic Systems TS-7250 platform. + Support for NAND flash on Texas Instruments OMAP2, OMAP3 and OMAP4 + platforms. + +config MTD_NAND_OMAP_BCH + depends on MTD_NAND_OMAP2 + tristate "Support hardware based BCH error correction" + default n + select BCH + help + This config enables the ELM hardware engine, which can be used to + locate and correct errors when using BCH ECC scheme. This offloads + the cpu from doing ECC error searching and correction. However some + legacy OMAP families like OMAP2xxx, OMAP3xxx do not have ELM engine + so they should not enable this config symbol. config MTD_NAND_IDS tristate +config MTD_NAND_RICOH + tristate "Ricoh xD card reader" + default n + depends on PCI + select MTD_SM_COMMON + help + Enable support for Ricoh R5C852 xD card reader + You also need to enable ether + NAND SSFDC (SmartMedia) read only translation layer' or new + expermental, readwrite + 'SmartMedia/xD new translation layer' + config MTD_NAND_AU1550 tristate "Au1550/1200 NAND support" - depends on SOC_AU1200 || SOC_AU1550 + depends on MIPS_ALCHEMY help This enables the driver for the NAND flash controller on the AMD/Alchemy 1550 SOC. config MTD_NAND_BF5XX tristate "Blackfin on-chip NAND Flash Controller driver" - depends on (BF54x || BF52x) && MTD_NAND + depends on BF54x || BF52x help This enables the Blackfin on-chip NAND flash controller @@ -122,44 +160,28 @@ config MTD_NAND_BF5XX_BOOTROM_ECC If unsure, say N. -config MTD_NAND_RTC_FROM4 - tristate "Renesas Flash ROM 4-slot interface board (FROM_BOARD4)" - depends on SH_SOLUTION_ENGINE - select REED_SOLOMON - select REED_SOLOMON_DEC8 - select BITREVERSE - help - This enables the driver for the Renesas Technology AG-AND - flash interface board (FROM_BOARD4) - -config MTD_NAND_PPCHAMELEONEVB - tristate "NAND Flash device on PPChameleonEVB board" - depends on PPCHAMELEONEVB && BROKEN - help - This enables the NAND flash driver on the PPChameleon EVB Board. - config MTD_NAND_S3C2410 - tristate "NAND Flash support for S3C2410/S3C2440 SoC" - depends on ARCH_S3C2410 + tristate "NAND Flash support for Samsung S3C SoCs" + depends on ARCH_S3C24XX || ARCH_S3C64XX help - This enables the NAND flash controller on the S3C2410 and S3C2440 + This enables the NAND flash controller on the S3C24xx and S3C64xx SoCs No board specific support is done by this driver, each board must advertise a platform_device for the driver to attach. config MTD_NAND_S3C2410_DEBUG - bool "S3C2410 NAND driver debug" + bool "Samsung S3C NAND driver debug" depends on MTD_NAND_S3C2410 help - Enable debugging of the S3C2410 NAND driver + Enable debugging of the S3C NAND driver config MTD_NAND_S3C2410_HWECC - bool "S3C2410 NAND Hardware ECC" + bool "Samsung S3C NAND Hardware ECC" depends on MTD_NAND_S3C2410 help - Enable the use of the S3C2410's internal ECC generator when - using NAND. Early versions of the chip have had problems with + Enable the use of the controller's internal ECC generator when + using NAND. Early versions of the chips have had problems with incorrect ECC generation, and if using these, the default of software ECC is preferable. @@ -171,7 +193,7 @@ config MTD_NAND_NDFC NDFC Nand Flash Controllers are integrated in IBM/AMCC's 4xx SoCs config MTD_NAND_S3C2410_CLKSTOP - bool "S3C2410 NAND IDLE clock stop" + bool "Samsung S3C NAND IDLE clock stop" depends on MTD_NAND_S3C2410 default n help @@ -181,8 +203,8 @@ config MTD_NAND_S3C2410_CLKSTOP approximately 5mA of power when there is nothing happening. config MTD_NAND_DISKONCHIP - tristate "DiskOnChip 2000, Millennium and Millennium Plus (NAND reimplementation) (EXPERIMENTAL)" - depends on EXPERIMENTAL + tristate "DiskOnChip 2000, Millennium and Millennium Plus (NAND reimplementation)" + depends on HAS_IOMEM select REED_SOLOMON select REED_SOLOMON_DEC16 help @@ -250,18 +272,30 @@ config MTD_NAND_DISKONCHIP_BBTWRITE load time (assuming you build diskonchip as a module) with the module parameter "inftl_bbt_write=1". +config MTD_NAND_DOCG4 + tristate "Support for DiskOnChip G4" + depends on HAS_IOMEM + select BCH + select BITREVERSE + help + Support for diskonchip G4 nand flash, found in various smartphones and + PDAs, among them the Palm Treo680, HTC Prophet and Wizard, Toshiba + Portege G900, Asus P526, and O2 XDA Zinc. + + With this driver you will be able to use UBI and create a ubifs on the + device, so you may wish to consider enabling UBI and UBIFS as well. + + These devices ship with the Mys/Sandisk SAFTL formatting, for which + there is currently no mtd parser, so you may want to use command line + partitioning to segregate write-protected blocks. On the Treo680, the + first five erase blocks (256KiB each) are write-protected, followed + by the block containing the saftl partition table. This is probably + typical. + config MTD_NAND_SHARPSL tristate "Support for NAND Flash on Sharp SL Series (C7xx + others)" depends on ARCH_PXA -config MTD_NAND_BASLER_EXCITE - tristate "Support for NAND Flash on Basler eXcite" - depends on BASLER_EXCITE - help - This enables the driver for the NAND flash device found on the - Basler eXcite Smart Camera. If built as a module, the driver - will be named "excite_nandflash.ko". - config MTD_NAND_CAFE tristate "NAND support for OLPC CAFÉ chip" depends on PCI @@ -273,7 +307,7 @@ config MTD_NAND_CAFE config MTD_NAND_CS553X tristate "NAND support for CS5535/CS5536 (AMD Geode companion chip)" - depends on X86_32 && (X86_PC || X86_GENERICARCH) + depends on X86_32 help The CS553x companion chips for the AMD Geode processor include NAND flash controllers with built-in hardware ECC @@ -282,7 +316,7 @@ config MTD_NAND_CS553X controller is enabled for NAND, and currently requires that the controller be in MMIO mode. - If you say "m", the module will be called "cs553x_nand.ko". + If you say "m", the module will be called cs553x_nand. config MTD_NAND_ATMEL tristate "Support for NAND Flash / SmartMedia on AT91 and AVR32" @@ -290,106 +324,90 @@ config MTD_NAND_ATMEL help Enables support for NAND Flash / Smart Media Card interface on Atmel AT91 and AVR32 processors. -choice - prompt "ECC management for NAND Flash / SmartMedia on AT91 / AVR32" - depends on MTD_NAND_ATMEL - -config MTD_NAND_ATMEL_ECC_HW - bool "Hardware ECC" - depends on ARCH_AT91SAM9263 || ARCH_AT91SAM9260 || AVR32 - help - Use hardware ECC instead of software ECC when the chip - supports it. - - The hardware ECC controller is capable of single bit error - correction and 2-bit random detection per page. - - NB : hardware and software ECC schemes are incompatible. - If you switch from one to another, you'll have to erase your - mtd partition. - If unsure, say Y - -config MTD_NAND_ATMEL_ECC_SOFT - bool "Software ECC" +config MTD_NAND_PXA3xx + tristate "NAND support on PXA3xx and Armada 370/XP" + depends on PXA3xx || ARCH_MMP || PLAT_ORION help - Use software ECC. - - NB : hardware and software ECC schemes are incompatible. - If you switch from one to another, you'll have to erase your - mtd partition. + This enables the driver for the NAND flash device found on + PXA3xx processors (NFCv1) and also on Armada 370/XP (NFCv2). -config MTD_NAND_ATMEL_ECC_NONE - bool "No ECC (testing only, DANGEROUS)" - depends on DEBUG_KERNEL +config MTD_NAND_SLC_LPC32XX + tristate "NXP LPC32xx SLC Controller" + depends on ARCH_LPC32XX help - No ECC will be used. - It's not a good idea and it should be reserved for testing - purpose only. - - If unsure, say N + Enables support for NXP's LPC32XX SLC (i.e. for Single Level Cell + chips) NAND controller. This is the default for the PHYTEC 3250 + reference board which contains a NAND256R3A2CZA6 chip. - endchoice + Please check the actual NAND chip connected and its support + by the SLC NAND controller. -endchoice - -config MTD_NAND_PXA3xx - bool "Support for NAND flash devices on PXA3xx" - depends on MTD_NAND && PXA3xx +config MTD_NAND_MLC_LPC32XX + tristate "NXP LPC32xx MLC Controller" + depends on ARCH_LPC32XX help - This enables the driver for the NAND flash device found on - PXA3xx processors + Uses the LPC32XX MLC (i.e. for Multi Level Cell chips) NAND + controller. This is the default for the WORK92105 controller + board. -config MTD_NAND_PXA3xx_BUILTIN - bool "Use builtin definitions for some NAND chips (deprecated)" - depends on MTD_NAND_PXA3xx - help - This enables builtin definitions for some NAND chips. This - is deprecated in favor of platform specific data. + Please check the actual NAND chip connected and its support + by the MLC NAND controller. config MTD_NAND_CM_X270 tristate "Support for NAND Flash on CM-X270 modules" - depends on MTD_NAND && MACH_ARMCORE + depends on MACH_ARMCORE config MTD_NAND_PASEMI tristate "NAND support for PA Semi PWRficient" - depends on MTD_NAND && PPC_PASEMI + depends on PPC_PASEMI help Enables support for NAND Flash interface on PA Semi PWRficient based boards config MTD_NAND_TMIO tristate "NAND Flash device on Toshiba Mobile IO Controller" - depends on MTD_NAND && MFD_TMIO + depends on MFD_TMIO help Support for NAND flash connected to a Toshiba Mobile IO Controller in some PDAs, including the Sharp SL6000x. config MTD_NAND_NANDSIM tristate "Support for NAND Flash Simulator" - depends on MTD_PARTITIONS help The simulator may simulate various NAND flash chips for the MTD nand layer. +config MTD_NAND_GPMI_NAND + tristate "GPMI NAND Flash Controller driver" + depends on MTD_NAND && MXS_DMA + help + Enables NAND Flash support for IMX23, IMX28 or IMX6. + The GPMI controller is very powerful, with the help of BCH + module, it can do the hardware ECC. The GPMI supports several + NAND flashs at the same time. The GPMI may conflicts with other + block, such as SD card. So pay attention to it when you enable + the GPMI. + +config MTD_NAND_BCM47XXNFLASH + tristate "Support for NAND flash on BCM4706 BCMA bus" + depends on BCMA_NFLASH + help + BCMA bus can have various flash memories attached, they are + registered by bcma as platform devices. This enables driver for + NAND flash memories. For now only BCM4706 is supported. + config MTD_NAND_PLATFORM tristate "Support for generic platform NAND driver" - depends on MTD_NAND + depends on HAS_IOMEM help This implements a generic NAND driver for on-SOC platform devices. You will need to provide platform-specific functions via platform_data. -config MTD_ALAUDA - tristate "MTD driver for Olympus MAUSB-10 and Fujifilm DPC-R1" - depends on MTD_NAND && USB - help - These two (and possibly other) Alauda-based cardreaders for - SmartMedia and xD allow raw flash access. - config MTD_NAND_ORION tristate "NAND Flash support for Marvell Orion SoC" - depends on PLAT_ORION && MTD_NAND + depends on PLAT_ORION help This enables the NAND flash controller on Orion machines. @@ -398,33 +416,101 @@ config MTD_NAND_ORION config MTD_NAND_FSL_ELBC tristate "NAND support for Freescale eLBC controllers" - depends on MTD_NAND && PPC_OF + depends on PPC_OF + select FSL_LBC help Various Freescale chips, including the 8313, include a NAND Flash Controller Module with built-in hardware ECC capabilities. Enabling this option will enable you to use this to control external NAND devices. +config MTD_NAND_FSL_IFC + tristate "NAND support for Freescale IFC controller" + depends on MTD_NAND && FSL_SOC + select FSL_IFC + select MEMORY + help + Various Freescale chips e.g P1010, include a NAND Flash machine + with built-in hardware ECC capabilities. + Enabling this option will enable you to use this to control + external NAND devices. + config MTD_NAND_FSL_UPM tristate "Support for NAND on Freescale UPM" - depends on MTD_NAND && (PPC_83xx || PPC_85xx) + depends on PPC_83xx || PPC_85xx select FSL_LBC help Enables support for NAND Flash chips wired onto Freescale PowerPC processor localbus with User-Programmable Machine support. +config MTD_NAND_MPC5121_NFC + tristate "MPC5121 built-in NAND Flash Controller support" + depends on PPC_MPC512x + help + This enables the driver for the NAND flash controller on the + MPC5121 SoC. + config MTD_NAND_MXC tristate "MXC NAND support" - depends on ARCH_MX2 || ARCH_MX3 + depends on ARCH_MXC help This enables the driver for the NAND flash controller on the MXC processors. config MTD_NAND_SH_FLCTL tristate "Support for NAND on Renesas SuperH FLCTL" - depends on MTD_NAND && SUPERH && CPU_SUBTYPE_SH7723 + depends on SUPERH || ARCH_SHMOBILE || COMPILE_TEST + depends on HAS_IOMEM + depends on HAS_DMA help Several Renesas SuperH CPU has FLCTL. This option enables support - for NAND Flash using FLCTL. This driver support SH7723. + for NAND Flash using FLCTL. + +config MTD_NAND_DAVINCI + tristate "Support NAND on DaVinci/Keystone SoC" + depends on ARCH_DAVINCI || (ARCH_KEYSTONE && TI_AEMIF) + help + Enable the driver for NAND flash chips on Texas Instruments + DaVinci/Keystone processors. + +config MTD_NAND_TXX9NDFMC + tristate "NAND Flash support for TXx9 SoC" + depends on SOC_TX4938 || SOC_TX4939 + help + This enables the NAND flash controller on the TXx9 SoCs. + +config MTD_NAND_SOCRATES + tristate "Support for NAND on Socrates board" + depends on SOCRATES + help + Enables support for NAND Flash chips wired onto Socrates board. + +config MTD_NAND_NUC900 + tristate "Support for NAND on Nuvoton NUC9xx/w90p910 evaluation boards." + depends on ARCH_W90X900 + help + This enables the driver for the NAND Flash on evaluation board based + on w90p910 / NUC9xx. + +config MTD_NAND_JZ4740 + tristate "Support for JZ4740 SoC NAND controller" + depends on MACH_JZ4740 + help + Enables support for NAND Flash on JZ4740 SoC based boards. + +config MTD_NAND_FSMC + tristate "Support for NAND on ST Micros FSMC" + depends on PLAT_SPEAR || ARCH_NOMADIK || ARCH_U8500 || MACH_U300 + help + Enables support for NAND Flash chips on the ST Microelectronics + Flexible Static Memory Controller (FSMC) + +config MTD_NAND_XWAY + tristate "Support for NAND on Lantiq XWAY SoC" + depends on LANTIQ && SOC_TYPE_XWAY + select MTD_NAND_PLATFORM + help + Enables support for NAND Flash chips on Lantiq XWAY SoCs. NAND is attached + to the External Bus Unit (EBU). endif # MTD_NAND |