diff options
Diffstat (limited to 'drivers/mtd/devices')
25 files changed, 4835 insertions, 5530 deletions
diff --git a/drivers/mtd/devices/Kconfig b/drivers/mtd/devices/Kconfig index 37b05c3f279..c49d0b127fe 100644 --- a/drivers/mtd/devices/Kconfig +++ b/drivers/mtd/devices/Kconfig @@ -1,5 +1,6 @@ menu "Self-contained MTD device drivers" depends on MTD!=n + depends on HAS_IOMEM config MTD_PMC551 tristate "Ramix PMC551 PCI Mezzanine RAM card support" @@ -51,7 +52,7 @@ config MTD_MS02NV config MTD_DATAFLASH tristate "Support for AT45xxx DataFlash" - depends on SPI_MASTER && EXPERIMENTAL + depends on SPI_MASTER help This enables access to AT45xxx DataFlash chips, using SPI. Sometimes DataFlash chips are packaged inside MMC-format @@ -70,7 +71,6 @@ config MTD_DATAFLASH_WRITE_VERIFY config MTD_DATAFLASH_OTP bool "DataFlash OTP support (Security Register)" depends on MTD_DATAFLASH - select HAVE_MTD_OTP help Newer DataFlash chips (revisions C and D) support 128 bytes of one-time-programmable (OTP) data. The first half may be written @@ -80,7 +80,7 @@ config MTD_DATAFLASH_OTP config MTD_M25P80 tristate "Support most SPI Flash chips (AT26DF, M25P, W25X, ...)" - depends on SPI_MASTER && EXPERIMENTAL + depends on SPI_MASTER && MTD_SPI_NOR help This enables access to most modern SPI flash chips, used for program and data storage. Series supported include Atmel AT26DF, @@ -95,12 +95,12 @@ config MTD_M25P80 if you want to specify device partitioning or to use a device which doesn't support the JEDEC ID instruction. -config M25PXX_USE_FAST_READ - bool "Use FAST_READ OPCode allowing SPI CLK <= 50MHz" - depends on MTD_M25P80 +config MTD_SPEAR_SMI + tristate "SPEAR MTD NOR Support through SMI controller" + depends on PLAT_SPEAR default y help - This option enables FAST_READ access supported by ST M25Pxx. + This enable SNOR support on SPEAR platforms using SMI controller config MTD_SST25L tristate "Support SST25L (non JEDEC) SPI Flash chips" @@ -112,6 +112,14 @@ config MTD_SST25L Set up your spi devices with the right board-specific platform data, if you want to specify device partitioning. +config MTD_BCM47XXSFLASH + tristate "R/O support for serial flash on BCMA bus" + depends on BCMA_SFLASH + help + BCMA bus can have various flash memories attached, they are + registered by bcma as platform devices. This enables driver for + serial flash memories (only read-only mode is implemented). + config MTD_SLRAM tristate "Uncached system RAM" help @@ -189,73 +197,11 @@ config MTD_BLOCK2MTD comment "Disk-On-Chip Device Drivers" -config MTD_DOC2000 - tristate "M-Systems Disk-On-Chip 2000 and Millennium (DEPRECATED)" - depends on MTD_NAND - select MTD_DOCPROBE - select MTD_NAND_IDS - ---help--- - This provides an MTD device driver for the M-Systems DiskOnChip - 2000 and Millennium devices. Originally designed for the DiskOnChip - 2000, it also now includes support for the DiskOnChip Millennium. - If you have problems with this driver and the DiskOnChip Millennium, - you may wish to try the alternative Millennium driver below. To use - the alternative driver, you will need to undefine DOC_SINGLE_DRIVER - in the <file:drivers/mtd/devices/docprobe.c> source code. - - If you use this device, you probably also want to enable the NFTL - 'NAND Flash Translation Layer' option below, which is used to - emulate a block device by using a kind of file system on the flash - chips. - - NOTE: This driver is deprecated and will probably be removed soon. - Please try the new DiskOnChip driver under "NAND Flash Device - Drivers". - -config MTD_DOC2001 - tristate "M-Systems Disk-On-Chip Millennium-only alternative driver (DEPRECATED)" - depends on MTD_NAND - select MTD_DOCPROBE - select MTD_NAND_IDS - ---help--- - This provides an alternative MTD device driver for the M-Systems - DiskOnChip Millennium devices. Use this if you have problems with - the combined DiskOnChip 2000 and Millennium driver above. To get - the DiskOnChip probe code to load and use this driver instead of - the other one, you will need to undefine DOC_SINGLE_DRIVER near - the beginning of <file:drivers/mtd/devices/docprobe.c>. - - If you use this device, you probably also want to enable the NFTL - 'NAND Flash Translation Layer' option below, which is used to - emulate a block device by using a kind of file system on the flash - chips. - - NOTE: This driver is deprecated and will probably be removed soon. - Please try the new DiskOnChip driver under "NAND Flash Device - Drivers". - -config MTD_DOC2001PLUS - tristate "M-Systems Disk-On-Chip Millennium Plus" - depends on MTD_NAND - select MTD_DOCPROBE - select MTD_NAND_IDS - ---help--- - This provides an MTD device driver for the M-Systems DiskOnChip - Millennium Plus devices. - - If you use this device, you probably also want to enable the INFTL - 'Inverse NAND Flash Translation Layer' option below, which is used - to emulate a block device by using a kind of file system on the - flash chips. - - NOTE: This driver will soon be replaced by the new DiskOnChip driver - under "NAND Flash Device Drivers" (currently that driver does not - support all Millennium Plus devices). - config MTD_DOCG3 tristate "M-Systems Disk-On-Chip G3" select BCH select BCH_CONST_PARAMS + select BITREVERSE ---help--- This provides an MTD device driver for the M-Systems DiskOnChip G3 devices. @@ -264,6 +210,14 @@ config MTD_DOCG3 M-Systems and now Sandisk. The support is very experimental, and doesn't give access to any write operations. +config MTD_ST_SPI_FSM + tristate "ST Microelectronics SPI FSM Serial Flash Controller" + depends on ARCH_STI + help + This provides an MTD device driver for the ST Microelectronics + SPI Fast Sequence Mode (FSM) Serial Flash Controller and support + for a subset of connected Serial Flash devices. + if MTD_DOCG3 config BCH_CONST_M default 14 @@ -271,59 +225,4 @@ config BCH_CONST_T default 4 endif -config MTD_DOCPROBE - tristate - select MTD_DOCECC - -config MTD_DOCECC - tristate - -config MTD_DOCPROBE_ADVANCED - bool "Advanced detection options for DiskOnChip" - depends on MTD_DOCPROBE - help - This option allows you to specify nonstandard address at which to - probe for a DiskOnChip, or to change the detection options. You - are unlikely to need any of this unless you are using LinuxBIOS. - Say 'N'. - -config MTD_DOCPROBE_ADDRESS - hex "Physical address of DiskOnChip" if MTD_DOCPROBE_ADVANCED - depends on MTD_DOCPROBE - default "0x0" - ---help--- - By default, the probe for DiskOnChip devices will look for a - DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000. - This option allows you to specify a single address at which to probe - for the device, which is useful if you have other devices in that - range which get upset when they are probed. - - (Note that on PowerPC, the normal probe will only check at - 0xE4000000.) - - Normally, you should leave this set to zero, to allow the probe at - the normal addresses. - -config MTD_DOCPROBE_HIGH - bool "Probe high addresses" - depends on MTD_DOCPROBE_ADVANCED - help - By default, the probe for DiskOnChip devices will look for a - DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000. - This option changes to make it probe between 0xFFFC8000 and - 0xFFFEE000. Unless you are using LinuxBIOS, this is unlikely to be - useful to you. Say 'N'. - -config MTD_DOCPROBE_55AA - bool "Probe for 0x55 0xAA BIOS Extension Signature" - depends on MTD_DOCPROBE_ADVANCED - help - Check for the 0x55 0xAA signature of a DiskOnChip, and do not - continue with probing if it is absent. The signature will always be - present for a DiskOnChip 2000 or a normal DiskOnChip Millennium. - Only if you have overwritten the first block of a DiskOnChip - Millennium will it be absent. Enable this option if you are using - LinuxBIOS or if you need to recover a DiskOnChip Millennium on which - you have managed to wipe the first block. - endmenu diff --git a/drivers/mtd/devices/Makefile b/drivers/mtd/devices/Makefile index 56c7cd462f1..c68868f6058 100644 --- a/drivers/mtd/devices/Makefile +++ b/drivers/mtd/devices/Makefile @@ -2,12 +2,7 @@ # linux/drivers/mtd/devices/Makefile # -obj-$(CONFIG_MTD_DOC2000) += doc2000.o -obj-$(CONFIG_MTD_DOC2001) += doc2001.o -obj-$(CONFIG_MTD_DOC2001PLUS) += doc2001plus.o obj-$(CONFIG_MTD_DOCG3) += docg3.o -obj-$(CONFIG_MTD_DOCPROBE) += docprobe.o -obj-$(CONFIG_MTD_DOCECC) += docecc.o obj-$(CONFIG_MTD_SLRAM) += slram.o obj-$(CONFIG_MTD_PHRAM) += phram.o obj-$(CONFIG_MTD_PMC551) += pmc551.o @@ -17,6 +12,11 @@ obj-$(CONFIG_MTD_LART) += lart.o obj-$(CONFIG_MTD_BLOCK2MTD) += block2mtd.o obj-$(CONFIG_MTD_DATAFLASH) += mtd_dataflash.o obj-$(CONFIG_MTD_M25P80) += m25p80.o +obj-$(CONFIG_MTD_NAND_OMAP_BCH) += elm.o +obj-$(CONFIG_MTD_SPEAR_SMI) += spear_smi.o obj-$(CONFIG_MTD_SST25L) += sst25l.o +obj-$(CONFIG_MTD_BCM47XXSFLASH) += bcm47xxsflash.o +obj-$(CONFIG_MTD_ST_SPI_FSM) += st_spi_fsm.o -CFLAGS_docg3.o += -I$(src)
\ No newline at end of file + +CFLAGS_docg3.o += -I$(src) diff --git a/drivers/mtd/devices/bcm47xxsflash.c b/drivers/mtd/devices/bcm47xxsflash.c new file mode 100644 index 00000000000..77de29bc02b --- /dev/null +++ b/drivers/mtd/devices/bcm47xxsflash.c @@ -0,0 +1,340 @@ +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/slab.h> +#include <linux/delay.h> +#include <linux/mtd/mtd.h> +#include <linux/platform_device.h> +#include <linux/bcma/bcma.h> + +#include "bcm47xxsflash.h" + +MODULE_LICENSE("GPL"); +MODULE_DESCRIPTION("Serial flash driver for BCMA bus"); + +static const char * const probes[] = { "bcm47xxpart", NULL }; + +/************************************************** + * Various helpers + **************************************************/ + +static void bcm47xxsflash_cmd(struct bcm47xxsflash *b47s, u32 opcode) +{ + int i; + + b47s->cc_write(b47s, BCMA_CC_FLASHCTL, BCMA_CC_FLASHCTL_START | opcode); + for (i = 0; i < 1000; i++) { + if (!(b47s->cc_read(b47s, BCMA_CC_FLASHCTL) & + BCMA_CC_FLASHCTL_BUSY)) + return; + cpu_relax(); + } + pr_err("Control command failed (timeout)!\n"); +} + +static int bcm47xxsflash_poll(struct bcm47xxsflash *b47s, int timeout) +{ + unsigned long deadline = jiffies + timeout; + + do { + switch (b47s->type) { + case BCM47XXSFLASH_TYPE_ST: + bcm47xxsflash_cmd(b47s, OPCODE_ST_RDSR); + if (!(b47s->cc_read(b47s, BCMA_CC_FLASHDATA) & + SR_ST_WIP)) + return 0; + break; + case BCM47XXSFLASH_TYPE_ATMEL: + bcm47xxsflash_cmd(b47s, OPCODE_AT_STATUS); + if (b47s->cc_read(b47s, BCMA_CC_FLASHDATA) & + SR_AT_READY) + return 0; + break; + } + + cpu_relax(); + udelay(1); + } while (!time_after_eq(jiffies, deadline)); + + pr_err("Timeout waiting for flash to be ready!\n"); + + return -EBUSY; +} + +/************************************************** + * MTD ops + **************************************************/ + +static int bcm47xxsflash_erase(struct mtd_info *mtd, struct erase_info *erase) +{ + struct bcm47xxsflash *b47s = mtd->priv; + int err; + + switch (b47s->type) { + case BCM47XXSFLASH_TYPE_ST: + bcm47xxsflash_cmd(b47s, OPCODE_ST_WREN); + b47s->cc_write(b47s, BCMA_CC_FLASHADDR, erase->addr); + /* Newer flashes have "sub-sectors" which can be erased + * independently with a new command: ST_SSE. The ST_SE command + * erases 64KB just as before. + */ + if (b47s->blocksize < (64 * 1024)) + bcm47xxsflash_cmd(b47s, OPCODE_ST_SSE); + else + bcm47xxsflash_cmd(b47s, OPCODE_ST_SE); + break; + case BCM47XXSFLASH_TYPE_ATMEL: + b47s->cc_write(b47s, BCMA_CC_FLASHADDR, erase->addr << 1); + bcm47xxsflash_cmd(b47s, OPCODE_AT_PAGE_ERASE); + break; + } + + err = bcm47xxsflash_poll(b47s, HZ); + if (err) + erase->state = MTD_ERASE_FAILED; + else + erase->state = MTD_ERASE_DONE; + + if (erase->callback) + erase->callback(erase); + + return err; +} + +static int bcm47xxsflash_read(struct mtd_info *mtd, loff_t from, size_t len, + size_t *retlen, u_char *buf) +{ + struct bcm47xxsflash *b47s = mtd->priv; + + /* Check address range */ + if ((from + len) > mtd->size) + return -EINVAL; + + memcpy_fromio(buf, (void __iomem *)KSEG0ADDR(b47s->window + from), + len); + *retlen = len; + + return len; +} + +static int bcm47xxsflash_write_st(struct mtd_info *mtd, u32 offset, size_t len, + const u_char *buf) +{ + struct bcm47xxsflash *b47s = mtd->priv; + int written = 0; + + /* Enable writes */ + bcm47xxsflash_cmd(b47s, OPCODE_ST_WREN); + + /* Write first byte */ + b47s->cc_write(b47s, BCMA_CC_FLASHADDR, offset); + b47s->cc_write(b47s, BCMA_CC_FLASHDATA, *buf++); + + /* Program page */ + if (b47s->bcma_cc->core->id.rev < 20) { + bcm47xxsflash_cmd(b47s, OPCODE_ST_PP); + return 1; /* 1B written */ + } + + /* Program page and set CSA (on newer chips we can continue writing) */ + bcm47xxsflash_cmd(b47s, OPCODE_ST_CSA | OPCODE_ST_PP); + offset++; + len--; + written++; + + while (len > 0) { + /* Page boundary, another function call is needed */ + if ((offset & 0xFF) == 0) + break; + + bcm47xxsflash_cmd(b47s, OPCODE_ST_CSA | *buf++); + offset++; + len--; + written++; + } + + /* All done, drop CSA & poll */ + b47s->cc_write(b47s, BCMA_CC_FLASHCTL, 0); + udelay(1); + if (bcm47xxsflash_poll(b47s, HZ / 10)) + pr_err("Flash rejected dropping CSA\n"); + + return written; +} + +static int bcm47xxsflash_write_at(struct mtd_info *mtd, u32 offset, size_t len, + const u_char *buf) +{ + struct bcm47xxsflash *b47s = mtd->priv; + u32 mask = b47s->blocksize - 1; + u32 page = (offset & ~mask) << 1; + u32 byte = offset & mask; + int written = 0; + + /* If we don't overwrite whole page, read it to the buffer first */ + if (byte || (len < b47s->blocksize)) { + int err; + + b47s->cc_write(b47s, BCMA_CC_FLASHADDR, page); + bcm47xxsflash_cmd(b47s, OPCODE_AT_BUF1_LOAD); + /* 250 us for AT45DB321B */ + err = bcm47xxsflash_poll(b47s, HZ / 1000); + if (err) { + pr_err("Timeout reading page 0x%X info buffer\n", page); + return err; + } + } + + /* Change buffer content with our data */ + while (len > 0) { + /* Page boundary, another function call is needed */ + if (byte == b47s->blocksize) + break; + + b47s->cc_write(b47s, BCMA_CC_FLASHADDR, byte++); + b47s->cc_write(b47s, BCMA_CC_FLASHDATA, *buf++); + bcm47xxsflash_cmd(b47s, OPCODE_AT_BUF1_WRITE); + len--; + written++; + } + + /* Program page with the buffer content */ + b47s->cc_write(b47s, BCMA_CC_FLASHADDR, page); + bcm47xxsflash_cmd(b47s, OPCODE_AT_BUF1_PROGRAM); + + return written; +} + +static int bcm47xxsflash_write(struct mtd_info *mtd, loff_t to, size_t len, + size_t *retlen, const u_char *buf) +{ + struct bcm47xxsflash *b47s = mtd->priv; + int written; + + /* Writing functions can return without writing all passed data, for + * example when the hardware is too old or when we git page boundary. + */ + while (len > 0) { + switch (b47s->type) { + case BCM47XXSFLASH_TYPE_ST: + written = bcm47xxsflash_write_st(mtd, to, len, buf); + break; + case BCM47XXSFLASH_TYPE_ATMEL: + written = bcm47xxsflash_write_at(mtd, to, len, buf); + break; + default: + BUG_ON(1); + } + if (written < 0) { + pr_err("Error writing at offset 0x%llX\n", to); + return written; + } + to += (loff_t)written; + len -= written; + *retlen += written; + buf += written; + } + + return 0; +} + +static void bcm47xxsflash_fill_mtd(struct bcm47xxsflash *b47s) +{ + struct mtd_info *mtd = &b47s->mtd; + + mtd->priv = b47s; + mtd->name = "bcm47xxsflash"; + mtd->owner = THIS_MODULE; + + mtd->type = MTD_NORFLASH; + mtd->flags = MTD_CAP_NORFLASH; + mtd->size = b47s->size; + mtd->erasesize = b47s->blocksize; + mtd->writesize = 1; + mtd->writebufsize = 1; + + mtd->_erase = bcm47xxsflash_erase; + mtd->_read = bcm47xxsflash_read; + mtd->_write = bcm47xxsflash_write; +} + +/************************************************** + * BCMA + **************************************************/ + +static int bcm47xxsflash_bcma_cc_read(struct bcm47xxsflash *b47s, u16 offset) +{ + return bcma_cc_read32(b47s->bcma_cc, offset); +} + +static void bcm47xxsflash_bcma_cc_write(struct bcm47xxsflash *b47s, u16 offset, + u32 value) +{ + bcma_cc_write32(b47s->bcma_cc, offset, value); +} + +static int bcm47xxsflash_bcma_probe(struct platform_device *pdev) +{ + struct bcma_sflash *sflash = dev_get_platdata(&pdev->dev); + struct bcm47xxsflash *b47s; + int err; + + b47s = devm_kzalloc(&pdev->dev, sizeof(*b47s), GFP_KERNEL); + if (!b47s) + return -ENOMEM; + sflash->priv = b47s; + + b47s->bcma_cc = container_of(sflash, struct bcma_drv_cc, sflash); + b47s->cc_read = bcm47xxsflash_bcma_cc_read; + b47s->cc_write = bcm47xxsflash_bcma_cc_write; + + switch (b47s->bcma_cc->capabilities & BCMA_CC_CAP_FLASHT) { + case BCMA_CC_FLASHT_STSER: + b47s->type = BCM47XXSFLASH_TYPE_ST; + break; + case BCMA_CC_FLASHT_ATSER: + b47s->type = BCM47XXSFLASH_TYPE_ATMEL; + break; + } + + b47s->window = sflash->window; + b47s->blocksize = sflash->blocksize; + b47s->numblocks = sflash->numblocks; + b47s->size = sflash->size; + bcm47xxsflash_fill_mtd(b47s); + + err = mtd_device_parse_register(&b47s->mtd, probes, NULL, NULL, 0); + if (err) { + pr_err("Failed to register MTD device: %d\n", err); + return err; + } + + if (bcm47xxsflash_poll(b47s, HZ / 10)) + pr_warn("Serial flash busy\n"); + + return 0; +} + +static int bcm47xxsflash_bcma_remove(struct platform_device *pdev) +{ + struct bcma_sflash *sflash = dev_get_platdata(&pdev->dev); + struct bcm47xxsflash *b47s = sflash->priv; + + mtd_device_unregister(&b47s->mtd); + + return 0; +} + +static struct platform_driver bcma_sflash_driver = { + .probe = bcm47xxsflash_bcma_probe, + .remove = bcm47xxsflash_bcma_remove, + .driver = { + .name = "bcma_sflash", + .owner = THIS_MODULE, + }, +}; + +/************************************************** + * Init + **************************************************/ + +module_platform_driver(bcma_sflash_driver); diff --git a/drivers/mtd/devices/bcm47xxsflash.h b/drivers/mtd/devices/bcm47xxsflash.h new file mode 100644 index 00000000000..fe93daf4f48 --- /dev/null +++ b/drivers/mtd/devices/bcm47xxsflash.h @@ -0,0 +1,76 @@ +#ifndef __BCM47XXSFLASH_H +#define __BCM47XXSFLASH_H + +#include <linux/mtd/mtd.h> + +/* Used for ST flashes only. */ +#define OPCODE_ST_WREN 0x0006 /* Write Enable */ +#define OPCODE_ST_WRDIS 0x0004 /* Write Disable */ +#define OPCODE_ST_RDSR 0x0105 /* Read Status Register */ +#define OPCODE_ST_WRSR 0x0101 /* Write Status Register */ +#define OPCODE_ST_READ 0x0303 /* Read Data Bytes */ +#define OPCODE_ST_PP 0x0302 /* Page Program */ +#define OPCODE_ST_SE 0x02d8 /* Sector Erase */ +#define OPCODE_ST_BE 0x00c7 /* Bulk Erase */ +#define OPCODE_ST_DP 0x00b9 /* Deep Power-down */ +#define OPCODE_ST_RES 0x03ab /* Read Electronic Signature */ +#define OPCODE_ST_CSA 0x1000 /* Keep chip select asserted */ +#define OPCODE_ST_SSE 0x0220 /* Sub-sector Erase */ + +/* Used for Atmel flashes only. */ +#define OPCODE_AT_READ 0x07e8 +#define OPCODE_AT_PAGE_READ 0x07d2 +#define OPCODE_AT_STATUS 0x01d7 +#define OPCODE_AT_BUF1_WRITE 0x0384 +#define OPCODE_AT_BUF2_WRITE 0x0387 +#define OPCODE_AT_BUF1_ERASE_PROGRAM 0x0283 +#define OPCODE_AT_BUF2_ERASE_PROGRAM 0x0286 +#define OPCODE_AT_BUF1_PROGRAM 0x0288 +#define OPCODE_AT_BUF2_PROGRAM 0x0289 +#define OPCODE_AT_PAGE_ERASE 0x0281 +#define OPCODE_AT_BLOCK_ERASE 0x0250 +#define OPCODE_AT_BUF1_WRITE_ERASE_PROGRAM 0x0382 +#define OPCODE_AT_BUF2_WRITE_ERASE_PROGRAM 0x0385 +#define OPCODE_AT_BUF1_LOAD 0x0253 +#define OPCODE_AT_BUF2_LOAD 0x0255 +#define OPCODE_AT_BUF1_COMPARE 0x0260 +#define OPCODE_AT_BUF2_COMPARE 0x0261 +#define OPCODE_AT_BUF1_REPROGRAM 0x0258 +#define OPCODE_AT_BUF2_REPROGRAM 0x0259 + +/* Status register bits for ST flashes */ +#define SR_ST_WIP 0x01 /* Write In Progress */ +#define SR_ST_WEL 0x02 /* Write Enable Latch */ +#define SR_ST_BP_MASK 0x1c /* Block Protect */ +#define SR_ST_BP_SHIFT 2 +#define SR_ST_SRWD 0x80 /* Status Register Write Disable */ + +/* Status register bits for Atmel flashes */ +#define SR_AT_READY 0x80 +#define SR_AT_MISMATCH 0x40 +#define SR_AT_ID_MASK 0x38 +#define SR_AT_ID_SHIFT 3 + +struct bcma_drv_cc; + +enum bcm47xxsflash_type { + BCM47XXSFLASH_TYPE_ATMEL, + BCM47XXSFLASH_TYPE_ST, +}; + +struct bcm47xxsflash { + struct bcma_drv_cc *bcma_cc; + int (*cc_read)(struct bcm47xxsflash *b47s, u16 offset); + void (*cc_write)(struct bcm47xxsflash *b47s, u16 offset, u32 value); + + enum bcm47xxsflash_type type; + + u32 window; + u32 blocksize; + u16 numblocks; + u32 size; + + struct mtd_info mtd; +}; + +#endif /* BCM47XXSFLASH */ diff --git a/drivers/mtd/devices/block2mtd.c b/drivers/mtd/devices/block2mtd.c index e7e46d1e746..66f0405f7e5 100644 --- a/drivers/mtd/devices/block2mtd.c +++ b/drivers/mtd/devices/block2mtd.c @@ -6,6 +6,9 @@ * * Licence: GPL */ + +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + #include <linux/module.h> #include <linux/fs.h> #include <linux/blkdev.h> @@ -17,10 +20,7 @@ #include <linux/mutex.h> #include <linux/mount.h> #include <linux/slab.h> - -#define ERROR(fmt, args...) printk(KERN_ERR "block2mtd: " fmt "\n" , ## args) -#define INFO(fmt, args...) printk(KERN_INFO "block2mtd: " fmt "\n" , ## args) - +#include <linux/major.h> /* Info for the block device */ struct block2mtd_dev { @@ -52,8 +52,6 @@ static int _block2mtd_erase(struct block2mtd_dev *dev, loff_t to, size_t len) while (pages) { page = page_read(mapping, index); - if (!page) - return -ENOMEM; if (IS_ERR(page)) return PTR_ERR(page); @@ -64,6 +62,7 @@ static int _block2mtd_erase(struct block2mtd_dev *dev, loff_t to, size_t len) memset(page_address(page), 0xff, PAGE_SIZE); set_page_dirty(page); unlock_page(page); + balance_dirty_pages_ratelimited(mapping); break; } @@ -85,7 +84,7 @@ static int block2mtd_erase(struct mtd_info *mtd, struct erase_info *instr) err = _block2mtd_erase(dev, from, len); mutex_unlock(&dev->write_mutex); if (err) { - ERROR("erase failed err = %d", err); + pr_err("erase failed err = %d\n", err); instr->state = MTD_ERASE_FAILED; } else instr->state = MTD_ERASE_DONE; @@ -104,14 +103,6 @@ static int block2mtd_read(struct mtd_info *mtd, loff_t from, size_t len, int offset = from & (PAGE_SIZE-1); int cpylen; - if (from > mtd->size) - return -EINVAL; - if (from + len > mtd->size) - len = mtd->size - from; - - if (retlen) - *retlen = 0; - while (len) { if ((offset + len) > PAGE_SIZE) cpylen = PAGE_SIZE - offset; // multiple pages @@ -120,8 +111,6 @@ static int block2mtd_read(struct mtd_info *mtd, loff_t from, size_t len, len = len - cpylen; page = page_read(dev->blkdev->bd_inode->i_mapping, index); - if (!page) - return -ENOMEM; if (IS_ERR(page)) return PTR_ERR(page); @@ -148,8 +137,6 @@ static int _block2mtd_write(struct block2mtd_dev *dev, const u_char *buf, int offset = to & ~PAGE_MASK; // page offset int cpylen; - if (retlen) - *retlen = 0; while (len) { if ((offset+len) > PAGE_SIZE) cpylen = PAGE_SIZE - offset; // multiple pages @@ -158,8 +145,6 @@ static int _block2mtd_write(struct block2mtd_dev *dev, const u_char *buf, len = len - cpylen; page = page_read(mapping, index); - if (!page) - return -ENOMEM; if (IS_ERR(page)) return PTR_ERR(page); @@ -168,6 +153,7 @@ static int _block2mtd_write(struct block2mtd_dev *dev, const u_char *buf, memcpy(page_address(page) + offset, buf, cpylen); set_page_dirty(page); unlock_page(page); + balance_dirty_pages_ratelimited(mapping); } page_cache_release(page); @@ -188,13 +174,6 @@ static int block2mtd_write(struct mtd_info *mtd, loff_t to, size_t len, struct block2mtd_dev *dev = mtd->priv; int err; - if (!len) - return 0; - if (to >= mtd->size) - return -ENOSPC; - if (to + len > mtd->size) - len = mtd->size - to; - mutex_lock(&dev->write_mutex); err = _block2mtd_write(dev, buf, to, len, retlen); mutex_unlock(&dev->write_mutex); @@ -230,7 +209,6 @@ static void block2mtd_free_device(struct block2mtd_dev *dev) } -/* FIXME: ensure that mtd->size % erase_size == 0 */ static struct block2mtd_dev *add_device(char *devname, int erase_size) { const fmode_t mode = FMODE_READ | FMODE_WRITE | FMODE_EXCL; @@ -260,14 +238,19 @@ static struct block2mtd_dev *add_device(char *devname, int erase_size) #endif if (IS_ERR(bdev)) { - ERROR("error: cannot open device %s", devname); - goto devinit_err; + pr_err("error: cannot open device %s\n", devname); + goto err_free_block2mtd; } dev->blkdev = bdev; if (MAJOR(bdev->bd_dev) == MTD_BLOCK_MAJOR) { - ERROR("attempting to use an MTD device as a block device"); - goto devinit_err; + pr_err("attempting to use an MTD device as a block device\n"); + goto err_free_block2mtd; + } + + if ((long)dev->blkdev->bd_inode->i_size % erase_size) { + pr_err("erasesize must be a divisor of device size\n"); + goto err_free_block2mtd; } mutex_init(&dev->write_mutex); @@ -276,34 +259,37 @@ static struct block2mtd_dev *add_device(char *devname, int erase_size) /* make the name contain the block device in */ name = kasprintf(GFP_KERNEL, "block2mtd: %s", devname); if (!name) - goto devinit_err; + goto err_destroy_mutex; dev->mtd.name = name; dev->mtd.size = dev->blkdev->bd_inode->i_size & PAGE_MASK; dev->mtd.erasesize = erase_size; dev->mtd.writesize = 1; + dev->mtd.writebufsize = PAGE_SIZE; dev->mtd.type = MTD_RAM; dev->mtd.flags = MTD_CAP_RAM; - dev->mtd.erase = block2mtd_erase; - dev->mtd.write = block2mtd_write; - dev->mtd.writev = mtd_writev; - dev->mtd.sync = block2mtd_sync; - dev->mtd.read = block2mtd_read; + dev->mtd._erase = block2mtd_erase; + dev->mtd._write = block2mtd_write; + dev->mtd._sync = block2mtd_sync; + dev->mtd._read = block2mtd_read; dev->mtd.priv = dev; dev->mtd.owner = THIS_MODULE; if (mtd_device_register(&dev->mtd, NULL, 0)) { /* Device didn't get added, so free the entry */ - goto devinit_err; + goto err_destroy_mutex; } list_add(&dev->list, &blkmtd_device_list); - INFO("mtd%d: [%s] erase_size = %dKiB [%d]", dev->mtd.index, - dev->mtd.name + strlen("block2mtd: "), - dev->mtd.erasesize >> 10, dev->mtd.erasesize); + pr_info("mtd%d: [%s] erase_size = %dKiB [%d]\n", + dev->mtd.index, + dev->mtd.name + strlen("block2mtd: "), + dev->mtd.erasesize >> 10, dev->mtd.erasesize); return dev; -devinit_err: +err_destroy_mutex: + mutex_destroy(&dev->write_mutex); +err_free_block2mtd: block2mtd_free_device(dev); return NULL; } @@ -360,17 +346,11 @@ static inline void kill_final_newline(char *str) } -#define parse_err(fmt, args...) do { \ - ERROR(fmt, ## args); \ - return 0; \ -} while (0) - #ifndef MODULE static int block2mtd_init_called = 0; static char block2mtd_paramline[80 + 12]; /* 80 for device, 12 for erase size */ #endif - static int block2mtd_setup2(const char *val) { char buf[80 + 12]; /* 80 for device, 12 for erase size */ @@ -380,8 +360,10 @@ static int block2mtd_setup2(const char *val) size_t erase_size = PAGE_SIZE; int i, ret; - if (strnlen(val, sizeof(buf)) >= sizeof(buf)) - parse_err("parameter too long"); + if (strnlen(val, sizeof(buf)) >= sizeof(buf)) { + pr_err("parameter too long\n"); + return 0; + } strcpy(str, val); kill_final_newline(str); @@ -389,20 +371,27 @@ static int block2mtd_setup2(const char *val) for (i = 0; i < 2; i++) token[i] = strsep(&str, ","); - if (str) - parse_err("too many arguments"); + if (str) { + pr_err("too many arguments\n"); + return 0; + } - if (!token[0]) - parse_err("no argument"); + if (!token[0]) { + pr_err("no argument\n"); + return 0; + } name = token[0]; - if (strlen(name) + 1 > 80) - parse_err("device name too long"); + if (strlen(name) + 1 > 80) { + pr_err("device name too long\n"); + return 0; + } if (token[1]) { ret = parse_num(&erase_size, token[1]); if (ret) { - parse_err("illegal erase size"); + pr_err("illegal erase size\n"); + return 0; } } @@ -456,7 +445,7 @@ static int __init block2mtd_init(void) } -static void __devexit block2mtd_exit(void) +static void block2mtd_exit(void) { struct list_head *pos, *next; @@ -465,8 +454,10 @@ static void __devexit block2mtd_exit(void) struct block2mtd_dev *dev = list_entry(pos, typeof(*dev), list); block2mtd_sync(&dev->mtd); mtd_device_unregister(&dev->mtd); - INFO("mtd%d: [%s] removed", dev->mtd.index, - dev->mtd.name + strlen("block2mtd: ")); + mutex_destroy(&dev->write_mutex); + pr_info("mtd%d: [%s] removed\n", + dev->mtd.index, + dev->mtd.name + strlen("block2mtd: ")); list_del(&dev->list); block2mtd_free_device(dev); } diff --git a/drivers/mtd/devices/doc2000.c b/drivers/mtd/devices/doc2000.c deleted file mode 100644 index b1cdf647901..00000000000 --- a/drivers/mtd/devices/doc2000.c +++ /dev/null @@ -1,1189 +0,0 @@ - -/* - * Linux driver for Disk-On-Chip 2000 and Millennium - * (c) 1999 Machine Vision Holdings, Inc. - * (c) 1999, 2000 David Woodhouse <dwmw2@infradead.org> - */ - -#include <linux/kernel.h> -#include <linux/module.h> -#include <asm/errno.h> -#include <asm/io.h> -#include <asm/uaccess.h> -#include <linux/delay.h> -#include <linux/slab.h> -#include <linux/sched.h> -#include <linux/init.h> -#include <linux/types.h> -#include <linux/bitops.h> -#include <linux/mutex.h> - -#include <linux/mtd/mtd.h> -#include <linux/mtd/nand.h> -#include <linux/mtd/doc2000.h> - -#define DOC_SUPPORT_2000 -#define DOC_SUPPORT_2000TSOP -#define DOC_SUPPORT_MILLENNIUM - -#ifdef DOC_SUPPORT_2000 -#define DoC_is_2000(doc) (doc->ChipID == DOC_ChipID_Doc2k) -#else -#define DoC_is_2000(doc) (0) -#endif - -#if defined(DOC_SUPPORT_2000TSOP) || defined(DOC_SUPPORT_MILLENNIUM) -#define DoC_is_Millennium(doc) (doc->ChipID == DOC_ChipID_DocMil) -#else -#define DoC_is_Millennium(doc) (0) -#endif - -/* #define ECC_DEBUG */ - -/* I have no idea why some DoC chips can not use memcpy_from|to_io(). - * This may be due to the different revisions of the ASIC controller built-in or - * simplily a QA/Bug issue. Who knows ?? If you have trouble, please uncomment - * this: - #undef USE_MEMCPY -*/ - -static int doc_read(struct mtd_info *mtd, loff_t from, size_t len, - size_t *retlen, u_char *buf); -static int doc_write(struct mtd_info *mtd, loff_t to, size_t len, - size_t *retlen, const u_char *buf); -static int doc_read_oob(struct mtd_info *mtd, loff_t ofs, - struct mtd_oob_ops *ops); -static int doc_write_oob(struct mtd_info *mtd, loff_t ofs, - struct mtd_oob_ops *ops); -static int doc_write_oob_nolock(struct mtd_info *mtd, loff_t ofs, size_t len, - size_t *retlen, const u_char *buf); -static int doc_erase (struct mtd_info *mtd, struct erase_info *instr); - -static struct mtd_info *doc2klist = NULL; - -/* Perform the required delay cycles by reading from the appropriate register */ -static void DoC_Delay(struct DiskOnChip *doc, unsigned short cycles) -{ - volatile char dummy; - int i; - - for (i = 0; i < cycles; i++) { - if (DoC_is_Millennium(doc)) - dummy = ReadDOC(doc->virtadr, NOP); - else - dummy = ReadDOC(doc->virtadr, DOCStatus); - } - -} - -/* DOC_WaitReady: Wait for RDY line to be asserted by the flash chip */ -static int _DoC_WaitReady(struct DiskOnChip *doc) -{ - void __iomem *docptr = doc->virtadr; - unsigned long timeo = jiffies + (HZ * 10); - - pr_debug("_DoC_WaitReady called for out-of-line wait\n"); - - /* Out-of-line routine to wait for chip response */ - while (!(ReadDOC(docptr, CDSNControl) & CDSN_CTRL_FR_B)) { - /* issue 2 read from NOP register after reading from CDSNControl register - see Software Requirement 11.4 item 2. */ - DoC_Delay(doc, 2); - - if (time_after(jiffies, timeo)) { - pr_debug("_DoC_WaitReady timed out.\n"); - return -EIO; - } - udelay(1); - cond_resched(); - } - - return 0; -} - -static inline int DoC_WaitReady(struct DiskOnChip *doc) -{ - void __iomem *docptr = doc->virtadr; - - /* This is inline, to optimise the common case, where it's ready instantly */ - int ret = 0; - - /* 4 read form NOP register should be issued in prior to the read from CDSNControl - see Software Requirement 11.4 item 2. */ - DoC_Delay(doc, 4); - - if (!(ReadDOC(docptr, CDSNControl) & CDSN_CTRL_FR_B)) - /* Call the out-of-line routine to wait */ - ret = _DoC_WaitReady(doc); - - /* issue 2 read from NOP register after reading from CDSNControl register - see Software Requirement 11.4 item 2. */ - DoC_Delay(doc, 2); - - return ret; -} - -/* DoC_Command: Send a flash command to the flash chip through the CDSN Slow IO register to - bypass the internal pipeline. Each of 4 delay cycles (read from the NOP register) is - required after writing to CDSN Control register, see Software Requirement 11.4 item 3. */ - -static int DoC_Command(struct DiskOnChip *doc, unsigned char command, - unsigned char xtraflags) -{ - void __iomem *docptr = doc->virtadr; - - if (DoC_is_2000(doc)) - xtraflags |= CDSN_CTRL_FLASH_IO; - - /* Assert the CLE (Command Latch Enable) line to the flash chip */ - WriteDOC(xtraflags | CDSN_CTRL_CLE | CDSN_CTRL_CE, docptr, CDSNControl); - DoC_Delay(doc, 4); /* Software requirement 11.4.3 for Millennium */ - - if (DoC_is_Millennium(doc)) - WriteDOC(command, docptr, CDSNSlowIO); - - /* Send the command */ - WriteDOC_(command, docptr, doc->ioreg); - if (DoC_is_Millennium(doc)) - WriteDOC(command, docptr, WritePipeTerm); - - /* Lower the CLE line */ - WriteDOC(xtraflags | CDSN_CTRL_CE, docptr, CDSNControl); - DoC_Delay(doc, 4); /* Software requirement 11.4.3 for Millennium */ - - /* Wait for the chip to respond - Software requirement 11.4.1 (extended for any command) */ - return DoC_WaitReady(doc); -} - -/* DoC_Address: Set the current address for the flash chip through the CDSN Slow IO register to - bypass the internal pipeline. Each of 4 delay cycles (read from the NOP register) is - required after writing to CDSN Control register, see Software Requirement 11.4 item 3. */ - -static int DoC_Address(struct DiskOnChip *doc, int numbytes, unsigned long ofs, - unsigned char xtraflags1, unsigned char xtraflags2) -{ - int i; - void __iomem *docptr = doc->virtadr; - - if (DoC_is_2000(doc)) - xtraflags1 |= CDSN_CTRL_FLASH_IO; - - /* Assert the ALE (Address Latch Enable) line to the flash chip */ - WriteDOC(xtraflags1 | CDSN_CTRL_ALE | CDSN_CTRL_CE, docptr, CDSNControl); - - DoC_Delay(doc, 4); /* Software requirement 11.4.3 for Millennium */ - - /* Send the address */ - /* Devices with 256-byte page are addressed as: - Column (bits 0-7), Page (bits 8-15, 16-23, 24-31) - * there is no device on the market with page256 - and more than 24 bits. - Devices with 512-byte page are addressed as: - Column (bits 0-7), Page (bits 9-16, 17-24, 25-31) - * 25-31 is sent only if the chip support it. - * bit 8 changes the read command to be sent - (NAND_CMD_READ0 or NAND_CMD_READ1). - */ - - if (numbytes == ADDR_COLUMN || numbytes == ADDR_COLUMN_PAGE) { - if (DoC_is_Millennium(doc)) - WriteDOC(ofs & 0xff, docptr, CDSNSlowIO); - WriteDOC_(ofs & 0xff, docptr, doc->ioreg); - } - - if (doc->page256) { - ofs = ofs >> 8; - } else { - ofs = ofs >> 9; - } - - if (numbytes == ADDR_PAGE || numbytes == ADDR_COLUMN_PAGE) { - for (i = 0; i < doc->pageadrlen; i++, ofs = ofs >> 8) { - if (DoC_is_Millennium(doc)) - WriteDOC(ofs & 0xff, docptr, CDSNSlowIO); - WriteDOC_(ofs & 0xff, docptr, doc->ioreg); - } - } - - if (DoC_is_Millennium(doc)) - WriteDOC(ofs & 0xff, docptr, WritePipeTerm); - - DoC_Delay(doc, 2); /* Needed for some slow flash chips. mf. */ - - /* FIXME: The SlowIO's for millennium could be replaced by - a single WritePipeTerm here. mf. */ - - /* Lower the ALE line */ - WriteDOC(xtraflags1 | xtraflags2 | CDSN_CTRL_CE, docptr, - CDSNControl); - - DoC_Delay(doc, 4); /* Software requirement 11.4.3 for Millennium */ - - /* Wait for the chip to respond - Software requirement 11.4.1 */ - return DoC_WaitReady(doc); -} - -/* Read a buffer from DoC, taking care of Millennium odditys */ -static void DoC_ReadBuf(struct DiskOnChip *doc, u_char * buf, int len) -{ - volatile int dummy; - int modulus = 0xffff; - void __iomem *docptr = doc->virtadr; - int i; - - if (len <= 0) - return; - - if (DoC_is_Millennium(doc)) { - /* Read the data via the internal pipeline through CDSN IO register, - see Pipelined Read Operations 11.3 */ - dummy = ReadDOC(docptr, ReadPipeInit); - - /* Millennium should use the LastDataRead register - Pipeline Reads */ - len--; - - /* This is needed for correctly ECC calculation */ - modulus = 0xff; - } - - for (i = 0; i < len; i++) - buf[i] = ReadDOC_(docptr, doc->ioreg + (i & modulus)); - - if (DoC_is_Millennium(doc)) { - buf[i] = ReadDOC(docptr, LastDataRead); - } -} - -/* Write a buffer to DoC, taking care of Millennium odditys */ -static void DoC_WriteBuf(struct DiskOnChip *doc, const u_char * buf, int len) -{ - void __iomem *docptr = doc->virtadr; - int i; - - if (len <= 0) - return; - - for (i = 0; i < len; i++) - WriteDOC_(buf[i], docptr, doc->ioreg + i); - - if (DoC_is_Millennium(doc)) { - WriteDOC(0x00, docptr, WritePipeTerm); - } -} - - -/* DoC_SelectChip: Select a given flash chip within the current floor */ - -static inline int DoC_SelectChip(struct DiskOnChip *doc, int chip) -{ - void __iomem *docptr = doc->virtadr; - - /* Software requirement 11.4.4 before writing DeviceSelect */ - /* Deassert the CE line to eliminate glitches on the FCE# outputs */ - WriteDOC(CDSN_CTRL_WP, docptr, CDSNControl); - DoC_Delay(doc, 4); /* Software requirement 11.4.3 for Millennium */ - - /* Select the individual flash chip requested */ - WriteDOC(chip, docptr, CDSNDeviceSelect); - DoC_Delay(doc, 4); - - /* Reassert the CE line */ - WriteDOC(CDSN_CTRL_CE | CDSN_CTRL_FLASH_IO | CDSN_CTRL_WP, docptr, - CDSNControl); - DoC_Delay(doc, 4); /* Software requirement 11.4.3 for Millennium */ - - /* Wait for it to be ready */ - return DoC_WaitReady(doc); -} - -/* DoC_SelectFloor: Select a given floor (bank of flash chips) */ - -static inline int DoC_SelectFloor(struct DiskOnChip *doc, int floor) -{ - void __iomem *docptr = doc->virtadr; - - /* Select the floor (bank) of chips required */ - WriteDOC(floor, docptr, FloorSelect); - - /* Wait for the chip to be ready */ - return DoC_WaitReady(doc); -} - -/* DoC_IdentChip: Identify a given NAND chip given {floor,chip} */ - -static int DoC_IdentChip(struct DiskOnChip *doc, int floor, int chip) -{ - int mfr, id, i, j; - volatile char dummy; - - /* Page in the required floor/chip */ - DoC_SelectFloor(doc, floor); - DoC_SelectChip(doc, chip); - - /* Reset the chip */ - if (DoC_Command(doc, NAND_CMD_RESET, CDSN_CTRL_WP)) { - pr_debug("DoC_Command (reset) for %d,%d returned true\n", - floor, chip); - return 0; - } - - - /* Read the NAND chip ID: 1. Send ReadID command */ - if (DoC_Command(doc, NAND_CMD_READID, CDSN_CTRL_WP)) { - pr_debug("DoC_Command (ReadID) for %d,%d returned true\n", - floor, chip); - return 0; - } - - /* Read the NAND chip ID: 2. Send address byte zero */ - DoC_Address(doc, ADDR_COLUMN, 0, CDSN_CTRL_WP, 0); - - /* Read the manufacturer and device id codes from the device */ - - if (DoC_is_Millennium(doc)) { - DoC_Delay(doc, 2); - dummy = ReadDOC(doc->virtadr, ReadPipeInit); - mfr = ReadDOC(doc->virtadr, LastDataRead); - - DoC_Delay(doc, 2); - dummy = ReadDOC(doc->virtadr, ReadPipeInit); - id = ReadDOC(doc->virtadr, LastDataRead); - } else { - /* CDSN Slow IO register see Software Req 11.4 item 5. */ - dummy = ReadDOC(doc->virtadr, CDSNSlowIO); - DoC_Delay(doc, 2); - mfr = ReadDOC_(doc->virtadr, doc->ioreg); - - /* CDSN Slow IO register see Software Req 11.4 item 5. */ - dummy = ReadDOC(doc->virtadr, CDSNSlowIO); - DoC_Delay(doc, 2); - id = ReadDOC_(doc->virtadr, doc->ioreg); - } - - /* No response - return failure */ - if (mfr == 0xff || mfr == 0) - return 0; - - /* Check it's the same as the first chip we identified. - * M-Systems say that any given DiskOnChip device should only - * contain _one_ type of flash part, although that's not a - * hardware restriction. */ - if (doc->mfr) { - if (doc->mfr == mfr && doc->id == id) - return 1; /* This is the same as the first */ - else - printk(KERN_WARNING - "Flash chip at floor %d, chip %d is different:\n", - floor, chip); - } - - /* Print and store the manufacturer and ID codes. */ - for (i = 0; nand_flash_ids[i].name != NULL; i++) { - if (id == nand_flash_ids[i].id) { - /* Try to identify manufacturer */ - for (j = 0; nand_manuf_ids[j].id != 0x0; j++) { - if (nand_manuf_ids[j].id == mfr) - break; - } - printk(KERN_INFO - "Flash chip found: Manufacturer ID: %2.2X, " - "Chip ID: %2.2X (%s:%s)\n", mfr, id, - nand_manuf_ids[j].name, nand_flash_ids[i].name); - if (!doc->mfr) { - doc->mfr = mfr; - doc->id = id; - doc->chipshift = - ffs((nand_flash_ids[i].chipsize << 20)) - 1; - doc->page256 = (nand_flash_ids[i].pagesize == 256) ? 1 : 0; - doc->pageadrlen = doc->chipshift > 25 ? 3 : 2; - doc->erasesize = - nand_flash_ids[i].erasesize; - return 1; - } - return 0; - } - } - - - /* We haven't fully identified the chip. Print as much as we know. */ - printk(KERN_WARNING "Unknown flash chip found: %2.2X %2.2X\n", - id, mfr); - - printk(KERN_WARNING "Please report to dwmw2@infradead.org\n"); - return 0; -} - -/* DoC_ScanChips: Find all NAND chips present in a DiskOnChip, and identify them */ - -static void DoC_ScanChips(struct DiskOnChip *this, int maxchips) -{ - int floor, chip; - int numchips[MAX_FLOORS]; - int ret = 1; - - this->numchips = 0; - this->mfr = 0; - this->id = 0; - - /* For each floor, find the number of valid chips it contains */ - for (floor = 0; floor < MAX_FLOORS; floor++) { - ret = 1; - numchips[floor] = 0; - for (chip = 0; chip < maxchips && ret != 0; chip++) { - - ret = DoC_IdentChip(this, floor, chip); - if (ret) { - numchips[floor]++; - this->numchips++; - } - } - } - - /* If there are none at all that we recognise, bail */ - if (!this->numchips) { - printk(KERN_NOTICE "No flash chips recognised.\n"); - return; - } - - /* Allocate an array to hold the information for each chip */ - this->chips = kmalloc(sizeof(struct Nand) * this->numchips, GFP_KERNEL); - if (!this->chips) { - printk(KERN_NOTICE "No memory for allocating chip info structures\n"); - return; - } - - ret = 0; - - /* Fill out the chip array with {floor, chipno} for each - * detected chip in the device. */ - for (floor = 0; floor < MAX_FLOORS; floor++) { - for (chip = 0; chip < numchips[floor]; chip++) { - this->chips[ret].floor = floor; - this->chips[ret].chip = chip; - this->chips[ret].curadr = 0; - this->chips[ret].curmode = 0x50; - ret++; - } - } - - /* Calculate and print the total size of the device */ - this->totlen = this->numchips * (1 << this->chipshift); - - printk(KERN_INFO "%d flash chips found. Total DiskOnChip size: %ld MiB\n", - this->numchips, this->totlen >> 20); -} - -static int DoC2k_is_alias(struct DiskOnChip *doc1, struct DiskOnChip *doc2) -{ - int tmp1, tmp2, retval; - if (doc1->physadr == doc2->physadr) - return 1; - - /* Use the alias resolution register which was set aside for this - * purpose. If it's value is the same on both chips, they might - * be the same chip, and we write to one and check for a change in - * the other. It's unclear if this register is usuable in the - * DoC 2000 (it's in the Millennium docs), but it seems to work. */ - tmp1 = ReadDOC(doc1->virtadr, AliasResolution); - tmp2 = ReadDOC(doc2->virtadr, AliasResolution); - if (tmp1 != tmp2) - return 0; - - WriteDOC((tmp1 + 1) % 0xff, doc1->virtadr, AliasResolution); - tmp2 = ReadDOC(doc2->virtadr, AliasResolution); - if (tmp2 == (tmp1 + 1) % 0xff) - retval = 1; - else - retval = 0; - - /* Restore register contents. May not be necessary, but do it just to - * be safe. */ - WriteDOC(tmp1, doc1->virtadr, AliasResolution); - - return retval; -} - -/* This routine is found from the docprobe code by symbol_get(), - * which will bump the use count of this module. */ -void DoC2k_init(struct mtd_info *mtd) -{ - struct DiskOnChip *this = mtd->priv; - struct DiskOnChip *old = NULL; - int maxchips; - - /* We must avoid being called twice for the same device. */ - - if (doc2klist) - old = doc2klist->priv; - - while (old) { - if (DoC2k_is_alias(old, this)) { - printk(KERN_NOTICE - "Ignoring DiskOnChip 2000 at 0x%lX - already configured\n", - this->physadr); - iounmap(this->virtadr); - kfree(mtd); - return; - } - if (old->nextdoc) - old = old->nextdoc->priv; - else - old = NULL; - } - - - switch (this->ChipID) { - case DOC_ChipID_Doc2kTSOP: - mtd->name = "DiskOnChip 2000 TSOP"; - this->ioreg = DoC_Mil_CDSN_IO; - /* Pretend it's a Millennium */ - this->ChipID = DOC_ChipID_DocMil; - maxchips = MAX_CHIPS; - break; - case DOC_ChipID_Doc2k: - mtd->name = "DiskOnChip 2000"; - this->ioreg = DoC_2k_CDSN_IO; - maxchips = MAX_CHIPS; - break; - case DOC_ChipID_DocMil: - mtd->name = "DiskOnChip Millennium"; - this->ioreg = DoC_Mil_CDSN_IO; - maxchips = MAX_CHIPS_MIL; - break; - default: - printk("Unknown ChipID 0x%02x\n", this->ChipID); - kfree(mtd); - iounmap(this->virtadr); - return; - } - - printk(KERN_NOTICE "%s found at address 0x%lX\n", mtd->name, - this->physadr); - - mtd->type = MTD_NANDFLASH; - mtd->flags = MTD_CAP_NANDFLASH; - mtd->writesize = 512; - mtd->oobsize = 16; - mtd->owner = THIS_MODULE; - mtd->erase = doc_erase; - mtd->read = doc_read; - mtd->write = doc_write; - mtd->read_oob = doc_read_oob; - mtd->write_oob = doc_write_oob; - this->curfloor = -1; - this->curchip = -1; - mutex_init(&this->lock); - - /* Ident all the chips present. */ - DoC_ScanChips(this, maxchips); - - if (!this->totlen) { - kfree(mtd); - iounmap(this->virtadr); - } else { - this->nextdoc = doc2klist; - doc2klist = mtd; - mtd->size = this->totlen; - mtd->erasesize = this->erasesize; - mtd_device_register(mtd, NULL, 0); - return; - } -} -EXPORT_SYMBOL_GPL(DoC2k_init); - -static int doc_read(struct mtd_info *mtd, loff_t from, size_t len, - size_t * retlen, u_char * buf) -{ - struct DiskOnChip *this = mtd->priv; - void __iomem *docptr = this->virtadr; - struct Nand *mychip; - unsigned char syndrome[6], eccbuf[6]; - volatile char dummy; - int i, len256 = 0, ret=0; - size_t left = len; - - /* Don't allow read past end of device */ - if (from >= this->totlen) - return -EINVAL; - - mutex_lock(&this->lock); - - *retlen = 0; - while (left) { - len = left; - - /* Don't allow a single read to cross a 512-byte block boundary */ - if (from + len > ((from | 0x1ff) + 1)) - len = ((from | 0x1ff) + 1) - from; - - /* The ECC will not be calculated correctly if less than 512 is read */ - if (len != 0x200) - printk(KERN_WARNING - "ECC needs a full sector read (adr: %lx size %lx)\n", - (long) from, (long) len); - - /* printk("DoC_Read (adr: %lx size %lx)\n", (long) from, (long) len); */ - - - /* Find the chip which is to be used and select it */ - mychip = &this->chips[from >> (this->chipshift)]; - - if (this->curfloor != mychip->floor) { - DoC_SelectFloor(this, mychip->floor); - DoC_SelectChip(this, mychip->chip); - } else if (this->curchip != mychip->chip) { - DoC_SelectChip(this, mychip->chip); - } - - this->curfloor = mychip->floor; - this->curchip = mychip->chip; - - DoC_Command(this, - (!this->page256 - && (from & 0x100)) ? NAND_CMD_READ1 : NAND_CMD_READ0, - CDSN_CTRL_WP); - DoC_Address(this, ADDR_COLUMN_PAGE, from, CDSN_CTRL_WP, - CDSN_CTRL_ECC_IO); - - /* Prime the ECC engine */ - WriteDOC(DOC_ECC_RESET, docptr, ECCConf); - WriteDOC(DOC_ECC_EN, docptr, ECCConf); - - /* treat crossing 256-byte sector for 2M x 8bits devices */ - if (this->page256 && from + len > (from | 0xff) + 1) { - len256 = (from | 0xff) + 1 - from; - DoC_ReadBuf(this, buf, len256); - - DoC_Command(this, NAND_CMD_READ0, CDSN_CTRL_WP); - DoC_Address(this, ADDR_COLUMN_PAGE, from + len256, - CDSN_CTRL_WP, CDSN_CTRL_ECC_IO); - } - - DoC_ReadBuf(this, &buf[len256], len - len256); - - /* Let the caller know we completed it */ - *retlen += len; - - /* Read the ECC data through the DiskOnChip ECC logic */ - /* Note: this will work even with 2M x 8bit devices as */ - /* they have 8 bytes of OOB per 256 page. mf. */ - DoC_ReadBuf(this, eccbuf, 6); - - /* Flush the pipeline */ - if (DoC_is_Millennium(this)) { - dummy = ReadDOC(docptr, ECCConf); - dummy = ReadDOC(docptr, ECCConf); - i = ReadDOC(docptr, ECCConf); - } else { - dummy = ReadDOC(docptr, 2k_ECCStatus); - dummy = ReadDOC(docptr, 2k_ECCStatus); - i = ReadDOC(docptr, 2k_ECCStatus); - } - - /* Check the ECC Status */ - if (i & 0x80) { - int nb_errors; - /* There was an ECC error */ -#ifdef ECC_DEBUG - printk(KERN_ERR "DiskOnChip ECC Error: Read at %lx\n", (long)from); -#endif - /* Read the ECC syndrome through the DiskOnChip ECC - logic. These syndrome will be all ZERO when there - is no error */ - for (i = 0; i < 6; i++) { - syndrome[i] = - ReadDOC(docptr, ECCSyndrome0 + i); - } - nb_errors = doc_decode_ecc(buf, syndrome); - -#ifdef ECC_DEBUG - printk(KERN_ERR "Errors corrected: %x\n", nb_errors); -#endif - if (nb_errors < 0) { - /* We return error, but have actually done the - read. Not that this can be told to - user-space, via sys_read(), but at least - MTD-aware stuff can know about it by - checking *retlen */ - ret = -EIO; - } - } - -#ifdef PSYCHO_DEBUG - printk(KERN_DEBUG "ECC DATA at %lxB: %2.2X %2.2X %2.2X %2.2X %2.2X %2.2X\n", - (long)from, eccbuf[0], eccbuf[1], eccbuf[2], - eccbuf[3], eccbuf[4], eccbuf[5]); -#endif - - /* disable the ECC engine */ - WriteDOC(DOC_ECC_DIS, docptr , ECCConf); - - /* according to 11.4.1, we need to wait for the busy line - * drop if we read to the end of the page. */ - if(0 == ((from + len) & 0x1ff)) - { - DoC_WaitReady(this); - } - - from += len; - left -= len; - buf += len; - } - - mutex_unlock(&this->lock); - - return ret; -} - -static int doc_write(struct mtd_info *mtd, loff_t to, size_t len, - size_t * retlen, const u_char * buf) -{ - struct DiskOnChip *this = mtd->priv; - int di; /* Yes, DI is a hangover from when I was disassembling the binary driver */ - void __iomem *docptr = this->virtadr; - unsigned char eccbuf[6]; - volatile char dummy; - int len256 = 0; - struct Nand *mychip; - size_t left = len; - int status; - - /* Don't allow write past end of device */ - if (to >= this->totlen) - return -EINVAL; - - mutex_lock(&this->lock); - - *retlen = 0; - while (left) { - len = left; - - /* Don't allow a single write to cross a 512-byte block boundary */ - if (to + len > ((to | 0x1ff) + 1)) - len = ((to | 0x1ff) + 1) - to; - - /* The ECC will not be calculated correctly if less than 512 is written */ -/* DBB- - if (len != 0x200 && eccbuf) - printk(KERN_WARNING - "ECC needs a full sector write (adr: %lx size %lx)\n", - (long) to, (long) len); - -DBB */ - - /* printk("DoC_Write (adr: %lx size %lx)\n", (long) to, (long) len); */ - - /* Find the chip which is to be used and select it */ - mychip = &this->chips[to >> (this->chipshift)]; - - if (this->curfloor != mychip->floor) { - DoC_SelectFloor(this, mychip->floor); - DoC_SelectChip(this, mychip->chip); - } else if (this->curchip != mychip->chip) { - DoC_SelectChip(this, mychip->chip); - } - - this->curfloor = mychip->floor; - this->curchip = mychip->chip; - - /* Set device to main plane of flash */ - DoC_Command(this, NAND_CMD_RESET, CDSN_CTRL_WP); - DoC_Command(this, - (!this->page256 - && (to & 0x100)) ? NAND_CMD_READ1 : NAND_CMD_READ0, - CDSN_CTRL_WP); - - DoC_Command(this, NAND_CMD_SEQIN, 0); - DoC_Address(this, ADDR_COLUMN_PAGE, to, 0, CDSN_CTRL_ECC_IO); - - /* Prime the ECC engine */ - WriteDOC(DOC_ECC_RESET, docptr, ECCConf); - WriteDOC(DOC_ECC_EN | DOC_ECC_RW, docptr, ECCConf); - - /* treat crossing 256-byte sector for 2M x 8bits devices */ - if (this->page256 && to + len > (to | 0xff) + 1) { - len256 = (to | 0xff) + 1 - to; - DoC_WriteBuf(this, buf, len256); - - DoC_Command(this, NAND_CMD_PAGEPROG, 0); - - DoC_Command(this, NAND_CMD_STATUS, CDSN_CTRL_WP); - /* There's an implicit DoC_WaitReady() in DoC_Command */ - - dummy = ReadDOC(docptr, CDSNSlowIO); - DoC_Delay(this, 2); - - if (ReadDOC_(docptr, this->ioreg) & 1) { - printk(KERN_ERR "Error programming flash\n"); - /* Error in programming */ - *retlen = 0; - mutex_unlock(&this->lock); - return -EIO; - } - - DoC_Command(this, NAND_CMD_SEQIN, 0); - DoC_Address(this, ADDR_COLUMN_PAGE, to + len256, 0, - CDSN_CTRL_ECC_IO); - } - - DoC_WriteBuf(this, &buf[len256], len - len256); - - WriteDOC(CDSN_CTRL_ECC_IO | CDSN_CTRL_CE, docptr, CDSNControl); - - if (DoC_is_Millennium(this)) { - WriteDOC(0, docptr, NOP); - WriteDOC(0, docptr, NOP); - WriteDOC(0, docptr, NOP); - } else { - WriteDOC_(0, docptr, this->ioreg); - WriteDOC_(0, docptr, this->ioreg); - WriteDOC_(0, docptr, this->ioreg); - } - - WriteDOC(CDSN_CTRL_ECC_IO | CDSN_CTRL_FLASH_IO | CDSN_CTRL_CE, docptr, - CDSNControl); - - /* Read the ECC data through the DiskOnChip ECC logic */ - for (di = 0; di < 6; di++) { - eccbuf[di] = ReadDOC(docptr, ECCSyndrome0 + di); - } - - /* Reset the ECC engine */ - WriteDOC(DOC_ECC_DIS, docptr, ECCConf); - -#ifdef PSYCHO_DEBUG - printk - ("OOB data at %lx is %2.2X %2.2X %2.2X %2.2X %2.2X %2.2X\n", - (long) to, eccbuf[0], eccbuf[1], eccbuf[2], eccbuf[3], - eccbuf[4], eccbuf[5]); -#endif - DoC_Command(this, NAND_CMD_PAGEPROG, 0); - - DoC_Command(this, NAND_CMD_STATUS, CDSN_CTRL_WP); - /* There's an implicit DoC_WaitReady() in DoC_Command */ - - if (DoC_is_Millennium(this)) { - ReadDOC(docptr, ReadPipeInit); - status = ReadDOC(docptr, LastDataRead); - } else { - dummy = ReadDOC(docptr, CDSNSlowIO); - DoC_Delay(this, 2); - status = ReadDOC_(docptr, this->ioreg); - } - - if (status & 1) { - printk(KERN_ERR "Error programming flash\n"); - /* Error in programming */ - *retlen = 0; - mutex_unlock(&this->lock); - return -EIO; - } - - /* Let the caller know we completed it */ - *retlen += len; - - { - unsigned char x[8]; - size_t dummy; - int ret; - - /* Write the ECC data to flash */ - for (di=0; di<6; di++) - x[di] = eccbuf[di]; - - x[6]=0x55; - x[7]=0x55; - - ret = doc_write_oob_nolock(mtd, to, 8, &dummy, x); - if (ret) { - mutex_unlock(&this->lock); - return ret; - } - } - - to += len; - left -= len; - buf += len; - } - - mutex_unlock(&this->lock); - return 0; -} - -static int doc_read_oob(struct mtd_info *mtd, loff_t ofs, - struct mtd_oob_ops *ops) -{ - struct DiskOnChip *this = mtd->priv; - int len256 = 0, ret; - struct Nand *mychip; - uint8_t *buf = ops->oobbuf; - size_t len = ops->len; - - BUG_ON(ops->mode != MTD_OPS_PLACE_OOB); - - ofs += ops->ooboffs; - - mutex_lock(&this->lock); - - mychip = &this->chips[ofs >> this->chipshift]; - - if (this->curfloor != mychip->floor) { - DoC_SelectFloor(this, mychip->floor); - DoC_SelectChip(this, mychip->chip); - } else if (this->curchip != mychip->chip) { - DoC_SelectChip(this, mychip->chip); - } - this->curfloor = mychip->floor; - this->curchip = mychip->chip; - - /* update address for 2M x 8bit devices. OOB starts on the second */ - /* page to maintain compatibility with doc_read_ecc. */ - if (this->page256) { - if (!(ofs & 0x8)) - ofs += 0x100; - else - ofs -= 0x8; - } - - DoC_Command(this, NAND_CMD_READOOB, CDSN_CTRL_WP); - DoC_Address(this, ADDR_COLUMN_PAGE, ofs, CDSN_CTRL_WP, 0); - - /* treat crossing 8-byte OOB data for 2M x 8bit devices */ - /* Note: datasheet says it should automaticaly wrap to the */ - /* next OOB block, but it didn't work here. mf. */ - if (this->page256 && ofs + len > (ofs | 0x7) + 1) { - len256 = (ofs | 0x7) + 1 - ofs; - DoC_ReadBuf(this, buf, len256); - - DoC_Command(this, NAND_CMD_READOOB, CDSN_CTRL_WP); - DoC_Address(this, ADDR_COLUMN_PAGE, ofs & (~0x1ff), - CDSN_CTRL_WP, 0); - } - - DoC_ReadBuf(this, &buf[len256], len - len256); - - ops->retlen = len; - /* Reading the full OOB data drops us off of the end of the page, - * causing the flash device to go into busy mode, so we need - * to wait until ready 11.4.1 and Toshiba TC58256FT docs */ - - ret = DoC_WaitReady(this); - - mutex_unlock(&this->lock); - return ret; - -} - -static int doc_write_oob_nolock(struct mtd_info *mtd, loff_t ofs, size_t len, - size_t * retlen, const u_char * buf) -{ - struct DiskOnChip *this = mtd->priv; - int len256 = 0; - void __iomem *docptr = this->virtadr; - struct Nand *mychip = &this->chips[ofs >> this->chipshift]; - volatile int dummy; - int status; - - // printk("doc_write_oob(%lx, %d): %2.2X %2.2X %2.2X %2.2X ... %2.2X %2.2X .. %2.2X %2.2X\n",(long)ofs, len, - // buf[0], buf[1], buf[2], buf[3], buf[8], buf[9], buf[14],buf[15]); - - /* Find the chip which is to be used and select it */ - if (this->curfloor != mychip->floor) { - DoC_SelectFloor(this, mychip->floor); - DoC_SelectChip(this, mychip->chip); - } else if (this->curchip != mychip->chip) { - DoC_SelectChip(this, mychip->chip); - } - this->curfloor = mychip->floor; - this->curchip = mychip->chip; - - /* disable the ECC engine */ - WriteDOC (DOC_ECC_RESET, docptr, ECCConf); - WriteDOC (DOC_ECC_DIS, docptr, ECCConf); - - /* Reset the chip, see Software Requirement 11.4 item 1. */ - DoC_Command(this, NAND_CMD_RESET, CDSN_CTRL_WP); - - /* issue the Read2 command to set the pointer to the Spare Data Area. */ - DoC_Command(this, NAND_CMD_READOOB, CDSN_CTRL_WP); - - /* update address for 2M x 8bit devices. OOB starts on the second */ - /* page to maintain compatibility with doc_read_ecc. */ - if (this->page256) { - if (!(ofs & 0x8)) - ofs += 0x100; - else - ofs -= 0x8; - } - - /* issue the Serial Data In command to initial the Page Program process */ - DoC_Command(this, NAND_CMD_SEQIN, 0); - DoC_Address(this, ADDR_COLUMN_PAGE, ofs, 0, 0); - - /* treat crossing 8-byte OOB data for 2M x 8bit devices */ - /* Note: datasheet says it should automaticaly wrap to the */ - /* next OOB block, but it didn't work here. mf. */ - if (this->page256 && ofs + len > (ofs | 0x7) + 1) { - len256 = (ofs | 0x7) + 1 - ofs; - DoC_WriteBuf(this, buf, len256); - - DoC_Command(this, NAND_CMD_PAGEPROG, 0); - DoC_Command(this, NAND_CMD_STATUS, 0); - /* DoC_WaitReady() is implicit in DoC_Command */ - - if (DoC_is_Millennium(this)) { - ReadDOC(docptr, ReadPipeInit); - status = ReadDOC(docptr, LastDataRead); - } else { - dummy = ReadDOC(docptr, CDSNSlowIO); - DoC_Delay(this, 2); - status = ReadDOC_(docptr, this->ioreg); - } - - if (status & 1) { - printk(KERN_ERR "Error programming oob data\n"); - /* There was an error */ - *retlen = 0; - return -EIO; - } - DoC_Command(this, NAND_CMD_SEQIN, 0); - DoC_Address(this, ADDR_COLUMN_PAGE, ofs & (~0x1ff), 0, 0); - } - - DoC_WriteBuf(this, &buf[len256], len - len256); - - DoC_Command(this, NAND_CMD_PAGEPROG, 0); - DoC_Command(this, NAND_CMD_STATUS, 0); - /* DoC_WaitReady() is implicit in DoC_Command */ - - if (DoC_is_Millennium(this)) { - ReadDOC(docptr, ReadPipeInit); - status = ReadDOC(docptr, LastDataRead); - } else { - dummy = ReadDOC(docptr, CDSNSlowIO); - DoC_Delay(this, 2); - status = ReadDOC_(docptr, this->ioreg); - } - - if (status & 1) { - printk(KERN_ERR "Error programming oob data\n"); - /* There was an error */ - *retlen = 0; - return -EIO; - } - - *retlen = len; - return 0; - -} - -static int doc_write_oob(struct mtd_info *mtd, loff_t ofs, - struct mtd_oob_ops *ops) -{ - struct DiskOnChip *this = mtd->priv; - int ret; - - BUG_ON(ops->mode != MTD_OPS_PLACE_OOB); - - mutex_lock(&this->lock); - ret = doc_write_oob_nolock(mtd, ofs + ops->ooboffs, ops->len, - &ops->retlen, ops->oobbuf); - - mutex_unlock(&this->lock); - return ret; -} - -static int doc_erase(struct mtd_info *mtd, struct erase_info *instr) -{ - struct DiskOnChip *this = mtd->priv; - __u32 ofs = instr->addr; - __u32 len = instr->len; - volatile int dummy; - void __iomem *docptr = this->virtadr; - struct Nand *mychip; - int status; - - mutex_lock(&this->lock); - - if (ofs & (mtd->erasesize-1) || len & (mtd->erasesize-1)) { - mutex_unlock(&this->lock); - return -EINVAL; - } - - instr->state = MTD_ERASING; - - /* FIXME: Do this in the background. Use timers or schedule_task() */ - while(len) { - mychip = &this->chips[ofs >> this->chipshift]; - - if (this->curfloor != mychip->floor) { - DoC_SelectFloor(this, mychip->floor); - DoC_SelectChip(this, mychip->chip); - } else if (this->curchip != mychip->chip) { - DoC_SelectChip(this, mychip->chip); - } - this->curfloor = mychip->floor; - this->curchip = mychip->chip; - - DoC_Command(this, NAND_CMD_ERASE1, 0); - DoC_Address(this, ADDR_PAGE, ofs, 0, 0); - DoC_Command(this, NAND_CMD_ERASE2, 0); - - DoC_Command(this, NAND_CMD_STATUS, CDSN_CTRL_WP); - - if (DoC_is_Millennium(this)) { - ReadDOC(docptr, ReadPipeInit); - status = ReadDOC(docptr, LastDataRead); - } else { - dummy = ReadDOC(docptr, CDSNSlowIO); - DoC_Delay(this, 2); - status = ReadDOC_(docptr, this->ioreg); - } - - if (status & 1) { - printk(KERN_ERR "Error erasing at 0x%x\n", ofs); - /* There was an error */ - instr->state = MTD_ERASE_FAILED; - goto callback; - } - ofs += mtd->erasesize; - len -= mtd->erasesize; - } - instr->state = MTD_ERASE_DONE; - - callback: - mtd_erase_callback(instr); - - mutex_unlock(&this->lock); - return 0; -} - - -/**************************************************************************** - * - * Module stuff - * - ****************************************************************************/ - -static void __exit cleanup_doc2000(void) -{ - struct mtd_info *mtd; - struct DiskOnChip *this; - - while ((mtd = doc2klist)) { - this = mtd->priv; - doc2klist = this->nextdoc; - - mtd_device_unregister(mtd); - - iounmap(this->virtadr); - kfree(this->chips); - kfree(mtd); - } -} - -module_exit(cleanup_doc2000); - -MODULE_LICENSE("GPL"); -MODULE_AUTHOR("David Woodhouse <dwmw2@infradead.org> et al."); -MODULE_DESCRIPTION("MTD driver for DiskOnChip 2000 and Millennium"); - diff --git a/drivers/mtd/devices/doc2001.c b/drivers/mtd/devices/doc2001.c deleted file mode 100644 index 7543b98f46c..00000000000 --- a/drivers/mtd/devices/doc2001.c +++ /dev/null @@ -1,832 +0,0 @@ - -/* - * Linux driver for Disk-On-Chip Millennium - * (c) 1999 Machine Vision Holdings, Inc. - * (c) 1999, 2000 David Woodhouse <dwmw2@infradead.org> - */ - -#include <linux/kernel.h> -#include <linux/module.h> -#include <asm/errno.h> -#include <asm/io.h> -#include <asm/uaccess.h> -#include <linux/delay.h> -#include <linux/slab.h> -#include <linux/init.h> -#include <linux/types.h> -#include <linux/bitops.h> - -#include <linux/mtd/mtd.h> -#include <linux/mtd/nand.h> -#include <linux/mtd/doc2000.h> - -/* #define ECC_DEBUG */ - -/* I have no idea why some DoC chips can not use memcop_form|to_io(). - * This may be due to the different revisions of the ASIC controller built-in or - * simplily a QA/Bug issue. Who knows ?? If you have trouble, please uncomment - * this:*/ -#undef USE_MEMCPY - -static int doc_read(struct mtd_info *mtd, loff_t from, size_t len, - size_t *retlen, u_char *buf); -static int doc_write(struct mtd_info *mtd, loff_t to, size_t len, - size_t *retlen, const u_char *buf); -static int doc_read_oob(struct mtd_info *mtd, loff_t ofs, - struct mtd_oob_ops *ops); -static int doc_write_oob(struct mtd_info *mtd, loff_t ofs, - struct mtd_oob_ops *ops); -static int doc_erase (struct mtd_info *mtd, struct erase_info *instr); - -static struct mtd_info *docmillist = NULL; - -/* Perform the required delay cycles by reading from the NOP register */ -static void DoC_Delay(void __iomem * docptr, unsigned short cycles) -{ - volatile char dummy; - int i; - - for (i = 0; i < cycles; i++) - dummy = ReadDOC(docptr, NOP); -} - -/* DOC_WaitReady: Wait for RDY line to be asserted by the flash chip */ -static int _DoC_WaitReady(void __iomem * docptr) -{ - unsigned short c = 0xffff; - - pr_debug("_DoC_WaitReady called for out-of-line wait\n"); - - /* Out-of-line routine to wait for chip response */ - while (!(ReadDOC(docptr, CDSNControl) & CDSN_CTRL_FR_B) && --c) - ; - - if (c == 0) - pr_debug("_DoC_WaitReady timed out.\n"); - - return (c == 0); -} - -static inline int DoC_WaitReady(void __iomem * docptr) -{ - /* This is inline, to optimise the common case, where it's ready instantly */ - int ret = 0; - - /* 4 read form NOP register should be issued in prior to the read from CDSNControl - see Software Requirement 11.4 item 2. */ - DoC_Delay(docptr, 4); - - if (!(ReadDOC(docptr, CDSNControl) & CDSN_CTRL_FR_B)) - /* Call the out-of-line routine to wait */ - ret = _DoC_WaitReady(docptr); - - /* issue 2 read from NOP register after reading from CDSNControl register - see Software Requirement 11.4 item 2. */ - DoC_Delay(docptr, 2); - - return ret; -} - -/* DoC_Command: Send a flash command to the flash chip through the CDSN IO register - with the internal pipeline. Each of 4 delay cycles (read from the NOP register) is - required after writing to CDSN Control register, see Software Requirement 11.4 item 3. */ - -static void DoC_Command(void __iomem * docptr, unsigned char command, - unsigned char xtraflags) -{ - /* Assert the CLE (Command Latch Enable) line to the flash chip */ - WriteDOC(xtraflags | CDSN_CTRL_CLE | CDSN_CTRL_CE, docptr, CDSNControl); - DoC_Delay(docptr, 4); - - /* Send the command */ - WriteDOC(command, docptr, Mil_CDSN_IO); - WriteDOC(0x00, docptr, WritePipeTerm); - - /* Lower the CLE line */ - WriteDOC(xtraflags | CDSN_CTRL_CE, docptr, CDSNControl); - DoC_Delay(docptr, 4); -} - -/* DoC_Address: Set the current address for the flash chip through the CDSN IO register - with the internal pipeline. Each of 4 delay cycles (read from the NOP register) is - required after writing to CDSN Control register, see Software Requirement 11.4 item 3. */ - -static inline void DoC_Address(void __iomem * docptr, int numbytes, unsigned long ofs, - unsigned char xtraflags1, unsigned char xtraflags2) -{ - /* Assert the ALE (Address Latch Enable) line to the flash chip */ - WriteDOC(xtraflags1 | CDSN_CTRL_ALE | CDSN_CTRL_CE, docptr, CDSNControl); - DoC_Delay(docptr, 4); - - /* Send the address */ - switch (numbytes) - { - case 1: - /* Send single byte, bits 0-7. */ - WriteDOC(ofs & 0xff, docptr, Mil_CDSN_IO); - WriteDOC(0x00, docptr, WritePipeTerm); - break; - case 2: - /* Send bits 9-16 followed by 17-23 */ - WriteDOC((ofs >> 9) & 0xff, docptr, Mil_CDSN_IO); - WriteDOC((ofs >> 17) & 0xff, docptr, Mil_CDSN_IO); - WriteDOC(0x00, docptr, WritePipeTerm); - break; - case 3: - /* Send 0-7, 9-16, then 17-23 */ - WriteDOC(ofs & 0xff, docptr, Mil_CDSN_IO); - WriteDOC((ofs >> 9) & 0xff, docptr, Mil_CDSN_IO); - WriteDOC((ofs >> 17) & 0xff, docptr, Mil_CDSN_IO); - WriteDOC(0x00, docptr, WritePipeTerm); - break; - default: - return; - } - - /* Lower the ALE line */ - WriteDOC(xtraflags1 | xtraflags2 | CDSN_CTRL_CE, docptr, CDSNControl); - DoC_Delay(docptr, 4); -} - -/* DoC_SelectChip: Select a given flash chip within the current floor */ -static int DoC_SelectChip(void __iomem * docptr, int chip) -{ - /* Select the individual flash chip requested */ - WriteDOC(chip, docptr, CDSNDeviceSelect); - DoC_Delay(docptr, 4); - - /* Wait for it to be ready */ - return DoC_WaitReady(docptr); -} - -/* DoC_SelectFloor: Select a given floor (bank of flash chips) */ -static int DoC_SelectFloor(void __iomem * docptr, int floor) -{ - /* Select the floor (bank) of chips required */ - WriteDOC(floor, docptr, FloorSelect); - - /* Wait for the chip to be ready */ - return DoC_WaitReady(docptr); -} - -/* DoC_IdentChip: Identify a given NAND chip given {floor,chip} */ -static int DoC_IdentChip(struct DiskOnChip *doc, int floor, int chip) -{ - int mfr, id, i, j; - volatile char dummy; - - /* Page in the required floor/chip - FIXME: is this supported by Millennium ?? */ - DoC_SelectFloor(doc->virtadr, floor); - DoC_SelectChip(doc->virtadr, chip); - - /* Reset the chip, see Software Requirement 11.4 item 1. */ - DoC_Command(doc->virtadr, NAND_CMD_RESET, CDSN_CTRL_WP); - DoC_WaitReady(doc->virtadr); - - /* Read the NAND chip ID: 1. Send ReadID command */ - DoC_Command(doc->virtadr, NAND_CMD_READID, CDSN_CTRL_WP); - - /* Read the NAND chip ID: 2. Send address byte zero */ - DoC_Address(doc->virtadr, 1, 0x00, CDSN_CTRL_WP, 0x00); - - /* Read the manufacturer and device id codes of the flash device through - CDSN IO register see Software Requirement 11.4 item 5.*/ - dummy = ReadDOC(doc->virtadr, ReadPipeInit); - DoC_Delay(doc->virtadr, 2); - mfr = ReadDOC(doc->virtadr, Mil_CDSN_IO); - - DoC_Delay(doc->virtadr, 2); - id = ReadDOC(doc->virtadr, Mil_CDSN_IO); - dummy = ReadDOC(doc->virtadr, LastDataRead); - - /* No response - return failure */ - if (mfr == 0xff || mfr == 0) - return 0; - - /* FIXME: to deal with multi-flash on multi-Millennium case more carefully */ - for (i = 0; nand_flash_ids[i].name != NULL; i++) { - if ( id == nand_flash_ids[i].id) { - /* Try to identify manufacturer */ - for (j = 0; nand_manuf_ids[j].id != 0x0; j++) { - if (nand_manuf_ids[j].id == mfr) - break; - } - printk(KERN_INFO "Flash chip found: Manufacturer ID: %2.2X, " - "Chip ID: %2.2X (%s:%s)\n", - mfr, id, nand_manuf_ids[j].name, nand_flash_ids[i].name); - doc->mfr = mfr; - doc->id = id; - doc->chipshift = ffs((nand_flash_ids[i].chipsize << 20)) - 1; - break; - } - } - - if (nand_flash_ids[i].name == NULL) - return 0; - else - return 1; -} - -/* DoC_ScanChips: Find all NAND chips present in a DiskOnChip, and identify them */ -static void DoC_ScanChips(struct DiskOnChip *this) -{ - int floor, chip; - int numchips[MAX_FLOORS_MIL]; - int ret; - - this->numchips = 0; - this->mfr = 0; - this->id = 0; - - /* For each floor, find the number of valid chips it contains */ - for (floor = 0,ret = 1; floor < MAX_FLOORS_MIL; floor++) { - numchips[floor] = 0; - for (chip = 0; chip < MAX_CHIPS_MIL && ret != 0; chip++) { - ret = DoC_IdentChip(this, floor, chip); - if (ret) { - numchips[floor]++; - this->numchips++; - } - } - } - /* If there are none at all that we recognise, bail */ - if (!this->numchips) { - printk("No flash chips recognised.\n"); - return; - } - - /* Allocate an array to hold the information for each chip */ - this->chips = kmalloc(sizeof(struct Nand) * this->numchips, GFP_KERNEL); - if (!this->chips){ - printk("No memory for allocating chip info structures\n"); - return; - } - - /* Fill out the chip array with {floor, chipno} for each - * detected chip in the device. */ - for (floor = 0, ret = 0; floor < MAX_FLOORS_MIL; floor++) { - for (chip = 0 ; chip < numchips[floor] ; chip++) { - this->chips[ret].floor = floor; - this->chips[ret].chip = chip; - this->chips[ret].curadr = 0; - this->chips[ret].curmode = 0x50; - ret++; - } - } - - /* Calculate and print the total size of the device */ - this->totlen = this->numchips * (1 << this->chipshift); - printk(KERN_INFO "%d flash chips found. Total DiskOnChip size: %ld MiB\n", - this->numchips ,this->totlen >> 20); -} - -static int DoCMil_is_alias(struct DiskOnChip *doc1, struct DiskOnChip *doc2) -{ - int tmp1, tmp2, retval; - - if (doc1->physadr == doc2->physadr) - return 1; - - /* Use the alias resolution register which was set aside for this - * purpose. If it's value is the same on both chips, they might - * be the same chip, and we write to one and check for a change in - * the other. It's unclear if this register is usuable in the - * DoC 2000 (it's in the Millenium docs), but it seems to work. */ - tmp1 = ReadDOC(doc1->virtadr, AliasResolution); - tmp2 = ReadDOC(doc2->virtadr, AliasResolution); - if (tmp1 != tmp2) - return 0; - - WriteDOC((tmp1+1) % 0xff, doc1->virtadr, AliasResolution); - tmp2 = ReadDOC(doc2->virtadr, AliasResolution); - if (tmp2 == (tmp1+1) % 0xff) - retval = 1; - else - retval = 0; - - /* Restore register contents. May not be necessary, but do it just to - * be safe. */ - WriteDOC(tmp1, doc1->virtadr, AliasResolution); - - return retval; -} - -/* This routine is found from the docprobe code by symbol_get(), - * which will bump the use count of this module. */ -void DoCMil_init(struct mtd_info *mtd) -{ - struct DiskOnChip *this = mtd->priv; - struct DiskOnChip *old = NULL; - - /* We must avoid being called twice for the same device. */ - if (docmillist) - old = docmillist->priv; - - while (old) { - if (DoCMil_is_alias(this, old)) { - printk(KERN_NOTICE "Ignoring DiskOnChip Millennium at " - "0x%lX - already configured\n", this->physadr); - iounmap(this->virtadr); - kfree(mtd); - return; - } - if (old->nextdoc) - old = old->nextdoc->priv; - else - old = NULL; - } - - mtd->name = "DiskOnChip Millennium"; - printk(KERN_NOTICE "DiskOnChip Millennium found at address 0x%lX\n", - this->physadr); - - mtd->type = MTD_NANDFLASH; - mtd->flags = MTD_CAP_NANDFLASH; - - /* FIXME: erase size is not always 8KiB */ - mtd->erasesize = 0x2000; - mtd->writesize = 512; - mtd->oobsize = 16; - mtd->owner = THIS_MODULE; - mtd->erase = doc_erase; - mtd->read = doc_read; - mtd->write = doc_write; - mtd->read_oob = doc_read_oob; - mtd->write_oob = doc_write_oob; - this->curfloor = -1; - this->curchip = -1; - - /* Ident all the chips present. */ - DoC_ScanChips(this); - - if (!this->totlen) { - kfree(mtd); - iounmap(this->virtadr); - } else { - this->nextdoc = docmillist; - docmillist = mtd; - mtd->size = this->totlen; - mtd_device_register(mtd, NULL, 0); - return; - } -} -EXPORT_SYMBOL_GPL(DoCMil_init); - -static int doc_read (struct mtd_info *mtd, loff_t from, size_t len, - size_t *retlen, u_char *buf) -{ - int i, ret; - volatile char dummy; - unsigned char syndrome[6], eccbuf[6]; - struct DiskOnChip *this = mtd->priv; - void __iomem *docptr = this->virtadr; - struct Nand *mychip = &this->chips[from >> (this->chipshift)]; - - /* Don't allow read past end of device */ - if (from >= this->totlen) - return -EINVAL; - - /* Don't allow a single read to cross a 512-byte block boundary */ - if (from + len > ((from | 0x1ff) + 1)) - len = ((from | 0x1ff) + 1) - from; - - /* Find the chip which is to be used and select it */ - if (this->curfloor != mychip->floor) { - DoC_SelectFloor(docptr, mychip->floor); - DoC_SelectChip(docptr, mychip->chip); - } else if (this->curchip != mychip->chip) { - DoC_SelectChip(docptr, mychip->chip); - } - this->curfloor = mychip->floor; - this->curchip = mychip->chip; - - /* issue the Read0 or Read1 command depend on which half of the page - we are accessing. Polling the Flash Ready bit after issue 3 bytes - address in Sequence Read Mode, see Software Requirement 11.4 item 1.*/ - DoC_Command(docptr, (from >> 8) & 1, CDSN_CTRL_WP); - DoC_Address(docptr, 3, from, CDSN_CTRL_WP, 0x00); - DoC_WaitReady(docptr); - - /* init the ECC engine, see Reed-Solomon EDC/ECC 11.1 .*/ - WriteDOC (DOC_ECC_RESET, docptr, ECCConf); - WriteDOC (DOC_ECC_EN, docptr, ECCConf); - - /* Read the data via the internal pipeline through CDSN IO register, - see Pipelined Read Operations 11.3 */ - dummy = ReadDOC(docptr, ReadPipeInit); -#ifndef USE_MEMCPY - for (i = 0; i < len-1; i++) { - /* N.B. you have to increase the source address in this way or the - ECC logic will not work properly */ - buf[i] = ReadDOC(docptr, Mil_CDSN_IO + (i & 0xff)); - } -#else - memcpy_fromio(buf, docptr + DoC_Mil_CDSN_IO, len - 1); -#endif - buf[len - 1] = ReadDOC(docptr, LastDataRead); - - /* Let the caller know we completed it */ - *retlen = len; - ret = 0; - - /* Read the ECC data from Spare Data Area, - see Reed-Solomon EDC/ECC 11.1 */ - dummy = ReadDOC(docptr, ReadPipeInit); -#ifndef USE_MEMCPY - for (i = 0; i < 5; i++) { - /* N.B. you have to increase the source address in this way or the - ECC logic will not work properly */ - eccbuf[i] = ReadDOC(docptr, Mil_CDSN_IO + i); - } -#else - memcpy_fromio(eccbuf, docptr + DoC_Mil_CDSN_IO, 5); -#endif - eccbuf[5] = ReadDOC(docptr, LastDataRead); - - /* Flush the pipeline */ - dummy = ReadDOC(docptr, ECCConf); - dummy = ReadDOC(docptr, ECCConf); - - /* Check the ECC Status */ - if (ReadDOC(docptr, ECCConf) & 0x80) { - int nb_errors; - /* There was an ECC error */ -#ifdef ECC_DEBUG - printk("DiskOnChip ECC Error: Read at %lx\n", (long)from); -#endif - /* Read the ECC syndrome through the DiskOnChip ECC logic. - These syndrome will be all ZERO when there is no error */ - for (i = 0; i < 6; i++) { - syndrome[i] = ReadDOC(docptr, ECCSyndrome0 + i); - } - nb_errors = doc_decode_ecc(buf, syndrome); -#ifdef ECC_DEBUG - printk("ECC Errors corrected: %x\n", nb_errors); -#endif - if (nb_errors < 0) { - /* We return error, but have actually done the read. Not that - this can be told to user-space, via sys_read(), but at least - MTD-aware stuff can know about it by checking *retlen */ - ret = -EIO; - } - } - -#ifdef PSYCHO_DEBUG - printk("ECC DATA at %lx: %2.2X %2.2X %2.2X %2.2X %2.2X %2.2X\n", - (long)from, eccbuf[0], eccbuf[1], eccbuf[2], eccbuf[3], - eccbuf[4], eccbuf[5]); -#endif - - /* disable the ECC engine */ - WriteDOC(DOC_ECC_DIS, docptr , ECCConf); - - return ret; -} - -static int doc_write (struct mtd_info *mtd, loff_t to, size_t len, - size_t *retlen, const u_char *buf) -{ - int i,ret = 0; - char eccbuf[6]; - volatile char dummy; - struct DiskOnChip *this = mtd->priv; - void __iomem *docptr = this->virtadr; - struct Nand *mychip = &this->chips[to >> (this->chipshift)]; - - /* Don't allow write past end of device */ - if (to >= this->totlen) - return -EINVAL; - -#if 0 - /* Don't allow a single write to cross a 512-byte block boundary */ - if (to + len > ( (to | 0x1ff) + 1)) - len = ((to | 0x1ff) + 1) - to; -#else - /* Don't allow writes which aren't exactly one block */ - if (to & 0x1ff || len != 0x200) - return -EINVAL; -#endif - - /* Find the chip which is to be used and select it */ - if (this->curfloor != mychip->floor) { - DoC_SelectFloor(docptr, mychip->floor); - DoC_SelectChip(docptr, mychip->chip); - } else if (this->curchip != mychip->chip) { - DoC_SelectChip(docptr, mychip->chip); - } - this->curfloor = mychip->floor; - this->curchip = mychip->chip; - - /* Reset the chip, see Software Requirement 11.4 item 1. */ - DoC_Command(docptr, NAND_CMD_RESET, 0x00); - DoC_WaitReady(docptr); - /* Set device to main plane of flash */ - DoC_Command(docptr, NAND_CMD_READ0, 0x00); - - /* issue the Serial Data In command to initial the Page Program process */ - DoC_Command(docptr, NAND_CMD_SEQIN, 0x00); - DoC_Address(docptr, 3, to, 0x00, 0x00); - DoC_WaitReady(docptr); - - /* init the ECC engine, see Reed-Solomon EDC/ECC 11.1 .*/ - WriteDOC (DOC_ECC_RESET, docptr, ECCConf); - WriteDOC (DOC_ECC_EN | DOC_ECC_RW, docptr, ECCConf); - - /* Write the data via the internal pipeline through CDSN IO register, - see Pipelined Write Operations 11.2 */ -#ifndef USE_MEMCPY - for (i = 0; i < len; i++) { - /* N.B. you have to increase the source address in this way or the - ECC logic will not work properly */ - WriteDOC(buf[i], docptr, Mil_CDSN_IO + i); - } -#else - memcpy_toio(docptr + DoC_Mil_CDSN_IO, buf, len); -#endif - WriteDOC(0x00, docptr, WritePipeTerm); - - /* Write ECC data to flash, the ECC info is generated by the DiskOnChip ECC logic - see Reed-Solomon EDC/ECC 11.1 */ - WriteDOC(0, docptr, NOP); - WriteDOC(0, docptr, NOP); - WriteDOC(0, docptr, NOP); - - /* Read the ECC data through the DiskOnChip ECC logic */ - for (i = 0; i < 6; i++) { - eccbuf[i] = ReadDOC(docptr, ECCSyndrome0 + i); - } - - /* ignore the ECC engine */ - WriteDOC(DOC_ECC_DIS, docptr , ECCConf); - -#ifndef USE_MEMCPY - /* Write the ECC data to flash */ - for (i = 0; i < 6; i++) { - /* N.B. you have to increase the source address in this way or the - ECC logic will not work properly */ - WriteDOC(eccbuf[i], docptr, Mil_CDSN_IO + i); - } -#else - memcpy_toio(docptr + DoC_Mil_CDSN_IO, eccbuf, 6); -#endif - - /* write the block status BLOCK_USED (0x5555) at the end of ECC data - FIXME: this is only a hack for programming the IPL area for LinuxBIOS - and should be replace with proper codes in user space utilities */ - WriteDOC(0x55, docptr, Mil_CDSN_IO); - WriteDOC(0x55, docptr, Mil_CDSN_IO + 1); - - WriteDOC(0x00, docptr, WritePipeTerm); - -#ifdef PSYCHO_DEBUG - printk("OOB data at %lx is %2.2X %2.2X %2.2X %2.2X %2.2X %2.2X\n", - (long) to, eccbuf[0], eccbuf[1], eccbuf[2], eccbuf[3], - eccbuf[4], eccbuf[5]); -#endif - - /* Commit the Page Program command and wait for ready - see Software Requirement 11.4 item 1.*/ - DoC_Command(docptr, NAND_CMD_PAGEPROG, 0x00); - DoC_WaitReady(docptr); - - /* Read the status of the flash device through CDSN IO register - see Software Requirement 11.4 item 5.*/ - DoC_Command(docptr, NAND_CMD_STATUS, CDSN_CTRL_WP); - dummy = ReadDOC(docptr, ReadPipeInit); - DoC_Delay(docptr, 2); - if (ReadDOC(docptr, Mil_CDSN_IO) & 1) { - printk("Error programming flash\n"); - /* Error in programming - FIXME: implement Bad Block Replacement (in nftl.c ??) */ - *retlen = 0; - ret = -EIO; - } - dummy = ReadDOC(docptr, LastDataRead); - - /* Let the caller know we completed it */ - *retlen = len; - - return ret; -} - -static int doc_read_oob(struct mtd_info *mtd, loff_t ofs, - struct mtd_oob_ops *ops) -{ -#ifndef USE_MEMCPY - int i; -#endif - volatile char dummy; - struct DiskOnChip *this = mtd->priv; - void __iomem *docptr = this->virtadr; - struct Nand *mychip = &this->chips[ofs >> this->chipshift]; - uint8_t *buf = ops->oobbuf; - size_t len = ops->len; - - BUG_ON(ops->mode != MTD_OPS_PLACE_OOB); - - ofs += ops->ooboffs; - - /* Find the chip which is to be used and select it */ - if (this->curfloor != mychip->floor) { - DoC_SelectFloor(docptr, mychip->floor); - DoC_SelectChip(docptr, mychip->chip); - } else if (this->curchip != mychip->chip) { - DoC_SelectChip(docptr, mychip->chip); - } - this->curfloor = mychip->floor; - this->curchip = mychip->chip; - - /* disable the ECC engine */ - WriteDOC (DOC_ECC_RESET, docptr, ECCConf); - WriteDOC (DOC_ECC_DIS, docptr, ECCConf); - - /* issue the Read2 command to set the pointer to the Spare Data Area. - Polling the Flash Ready bit after issue 3 bytes address in - Sequence Read Mode, see Software Requirement 11.4 item 1.*/ - DoC_Command(docptr, NAND_CMD_READOOB, CDSN_CTRL_WP); - DoC_Address(docptr, 3, ofs, CDSN_CTRL_WP, 0x00); - DoC_WaitReady(docptr); - - /* Read the data out via the internal pipeline through CDSN IO register, - see Pipelined Read Operations 11.3 */ - dummy = ReadDOC(docptr, ReadPipeInit); -#ifndef USE_MEMCPY - for (i = 0; i < len-1; i++) { - /* N.B. you have to increase the source address in this way or the - ECC logic will not work properly */ - buf[i] = ReadDOC(docptr, Mil_CDSN_IO + i); - } -#else - memcpy_fromio(buf, docptr + DoC_Mil_CDSN_IO, len - 1); -#endif - buf[len - 1] = ReadDOC(docptr, LastDataRead); - - ops->retlen = len; - - return 0; -} - -static int doc_write_oob(struct mtd_info *mtd, loff_t ofs, - struct mtd_oob_ops *ops) -{ -#ifndef USE_MEMCPY - int i; -#endif - volatile char dummy; - int ret = 0; - struct DiskOnChip *this = mtd->priv; - void __iomem *docptr = this->virtadr; - struct Nand *mychip = &this->chips[ofs >> this->chipshift]; - uint8_t *buf = ops->oobbuf; - size_t len = ops->len; - - BUG_ON(ops->mode != MTD_OPS_PLACE_OOB); - - ofs += ops->ooboffs; - - /* Find the chip which is to be used and select it */ - if (this->curfloor != mychip->floor) { - DoC_SelectFloor(docptr, mychip->floor); - DoC_SelectChip(docptr, mychip->chip); - } else if (this->curchip != mychip->chip) { - DoC_SelectChip(docptr, mychip->chip); - } - this->curfloor = mychip->floor; - this->curchip = mychip->chip; - - /* disable the ECC engine */ - WriteDOC (DOC_ECC_RESET, docptr, ECCConf); - WriteDOC (DOC_ECC_DIS, docptr, ECCConf); - - /* Reset the chip, see Software Requirement 11.4 item 1. */ - DoC_Command(docptr, NAND_CMD_RESET, CDSN_CTRL_WP); - DoC_WaitReady(docptr); - /* issue the Read2 command to set the pointer to the Spare Data Area. */ - DoC_Command(docptr, NAND_CMD_READOOB, CDSN_CTRL_WP); - - /* issue the Serial Data In command to initial the Page Program process */ - DoC_Command(docptr, NAND_CMD_SEQIN, 0x00); - DoC_Address(docptr, 3, ofs, 0x00, 0x00); - - /* Write the data via the internal pipeline through CDSN IO register, - see Pipelined Write Operations 11.2 */ -#ifndef USE_MEMCPY - for (i = 0; i < len; i++) { - /* N.B. you have to increase the source address in this way or the - ECC logic will not work properly */ - WriteDOC(buf[i], docptr, Mil_CDSN_IO + i); - } -#else - memcpy_toio(docptr + DoC_Mil_CDSN_IO, buf, len); -#endif - WriteDOC(0x00, docptr, WritePipeTerm); - - /* Commit the Page Program command and wait for ready - see Software Requirement 11.4 item 1.*/ - DoC_Command(docptr, NAND_CMD_PAGEPROG, 0x00); - DoC_WaitReady(docptr); - - /* Read the status of the flash device through CDSN IO register - see Software Requirement 11.4 item 5.*/ - DoC_Command(docptr, NAND_CMD_STATUS, 0x00); - dummy = ReadDOC(docptr, ReadPipeInit); - DoC_Delay(docptr, 2); - if (ReadDOC(docptr, Mil_CDSN_IO) & 1) { - printk("Error programming oob data\n"); - /* FIXME: implement Bad Block Replacement (in nftl.c ??) */ - ops->retlen = 0; - ret = -EIO; - } - dummy = ReadDOC(docptr, LastDataRead); - - ops->retlen = len; - - return ret; -} - -int doc_erase (struct mtd_info *mtd, struct erase_info *instr) -{ - volatile char dummy; - struct DiskOnChip *this = mtd->priv; - __u32 ofs = instr->addr; - __u32 len = instr->len; - void __iomem *docptr = this->virtadr; - struct Nand *mychip = &this->chips[ofs >> this->chipshift]; - - if (len != mtd->erasesize) - printk(KERN_WARNING "Erase not right size (%x != %x)n", - len, mtd->erasesize); - - /* Find the chip which is to be used and select it */ - if (this->curfloor != mychip->floor) { - DoC_SelectFloor(docptr, mychip->floor); - DoC_SelectChip(docptr, mychip->chip); - } else if (this->curchip != mychip->chip) { - DoC_SelectChip(docptr, mychip->chip); - } - this->curfloor = mychip->floor; - this->curchip = mychip->chip; - - instr->state = MTD_ERASE_PENDING; - - /* issue the Erase Setup command */ - DoC_Command(docptr, NAND_CMD_ERASE1, 0x00); - DoC_Address(docptr, 2, ofs, 0x00, 0x00); - - /* Commit the Erase Start command and wait for ready - see Software Requirement 11.4 item 1.*/ - DoC_Command(docptr, NAND_CMD_ERASE2, 0x00); - DoC_WaitReady(docptr); - - instr->state = MTD_ERASING; - - /* Read the status of the flash device through CDSN IO register - see Software Requirement 11.4 item 5. - FIXME: it seems that we are not wait long enough, some blocks are not - erased fully */ - DoC_Command(docptr, NAND_CMD_STATUS, CDSN_CTRL_WP); - dummy = ReadDOC(docptr, ReadPipeInit); - DoC_Delay(docptr, 2); - if (ReadDOC(docptr, Mil_CDSN_IO) & 1) { - printk("Error Erasing at 0x%x\n", ofs); - /* There was an error - FIXME: implement Bad Block Replacement (in nftl.c ??) */ - instr->state = MTD_ERASE_FAILED; - } else - instr->state = MTD_ERASE_DONE; - dummy = ReadDOC(docptr, LastDataRead); - - mtd_erase_callback(instr); - - return 0; -} - -/**************************************************************************** - * - * Module stuff - * - ****************************************************************************/ - -static void __exit cleanup_doc2001(void) -{ - struct mtd_info *mtd; - struct DiskOnChip *this; - - while ((mtd=docmillist)) { - this = mtd->priv; - docmillist = this->nextdoc; - - mtd_device_unregister(mtd); - - iounmap(this->virtadr); - kfree(this->chips); - kfree(mtd); - } -} - -module_exit(cleanup_doc2001); - -MODULE_LICENSE("GPL"); -MODULE_AUTHOR("David Woodhouse <dwmw2@infradead.org> et al."); -MODULE_DESCRIPTION("Alternative driver for DiskOnChip Millennium"); diff --git a/drivers/mtd/devices/doc2001plus.c b/drivers/mtd/devices/doc2001plus.c deleted file mode 100644 index 177510d0e7e..00000000000 --- a/drivers/mtd/devices/doc2001plus.c +++ /dev/null @@ -1,1096 +0,0 @@ -/* - * Linux driver for Disk-On-Chip Millennium Plus - * - * (c) 2002-2003 Greg Ungerer <gerg@snapgear.com> - * (c) 2002-2003 SnapGear Inc - * (c) 1999 Machine Vision Holdings, Inc. - * (c) 1999, 2000 David Woodhouse <dwmw2@infradead.org> - * - * Released under GPL - */ - -#include <linux/kernel.h> -#include <linux/module.h> -#include <asm/errno.h> -#include <asm/io.h> -#include <asm/uaccess.h> -#include <linux/delay.h> -#include <linux/slab.h> -#include <linux/init.h> -#include <linux/types.h> -#include <linux/bitops.h> - -#include <linux/mtd/mtd.h> -#include <linux/mtd/nand.h> -#include <linux/mtd/doc2000.h> - -/* #define ECC_DEBUG */ - -/* I have no idea why some DoC chips can not use memcop_form|to_io(). - * This may be due to the different revisions of the ASIC controller built-in or - * simplily a QA/Bug issue. Who knows ?? If you have trouble, please uncomment - * this:*/ -#undef USE_MEMCPY - -static int doc_read(struct mtd_info *mtd, loff_t from, size_t len, - size_t *retlen, u_char *buf); -static int doc_write(struct mtd_info *mtd, loff_t to, size_t len, - size_t *retlen, const u_char *buf); -static int doc_read_oob(struct mtd_info *mtd, loff_t ofs, - struct mtd_oob_ops *ops); -static int doc_write_oob(struct mtd_info *mtd, loff_t ofs, - struct mtd_oob_ops *ops); -static int doc_erase (struct mtd_info *mtd, struct erase_info *instr); - -static struct mtd_info *docmilpluslist = NULL; - - -/* Perform the required delay cycles by writing to the NOP register */ -static void DoC_Delay(void __iomem * docptr, int cycles) -{ - int i; - - for (i = 0; (i < cycles); i++) - WriteDOC(0, docptr, Mplus_NOP); -} - -#define CDSN_CTRL_FR_B_MASK (CDSN_CTRL_FR_B0 | CDSN_CTRL_FR_B1) - -/* DOC_WaitReady: Wait for RDY line to be asserted by the flash chip */ -static int _DoC_WaitReady(void __iomem * docptr) -{ - unsigned int c = 0xffff; - - pr_debug("_DoC_WaitReady called for out-of-line wait\n"); - - /* Out-of-line routine to wait for chip response */ - while (((ReadDOC(docptr, Mplus_FlashControl) & CDSN_CTRL_FR_B_MASK) != CDSN_CTRL_FR_B_MASK) && --c) - ; - - if (c == 0) - pr_debug("_DoC_WaitReady timed out.\n"); - - return (c == 0); -} - -static inline int DoC_WaitReady(void __iomem * docptr) -{ - /* This is inline, to optimise the common case, where it's ready instantly */ - int ret = 0; - - /* read form NOP register should be issued prior to the read from CDSNControl - see Software Requirement 11.4 item 2. */ - DoC_Delay(docptr, 4); - - if ((ReadDOC(docptr, Mplus_FlashControl) & CDSN_CTRL_FR_B_MASK) != CDSN_CTRL_FR_B_MASK) - /* Call the out-of-line routine to wait */ - ret = _DoC_WaitReady(docptr); - - return ret; -} - -/* For some reason the Millennium Plus seems to occasionally put itself - * into reset mode. For me this happens randomly, with no pattern that I - * can detect. M-systems suggest always check this on any block level - * operation and setting to normal mode if in reset mode. - */ -static inline void DoC_CheckASIC(void __iomem * docptr) -{ - /* Make sure the DoC is in normal mode */ - if ((ReadDOC(docptr, Mplus_DOCControl) & DOC_MODE_NORMAL) == 0) { - WriteDOC((DOC_MODE_NORMAL | DOC_MODE_MDWREN), docptr, Mplus_DOCControl); - WriteDOC(~(DOC_MODE_NORMAL | DOC_MODE_MDWREN), docptr, Mplus_CtrlConfirm); - } -} - -/* DoC_Command: Send a flash command to the flash chip through the Flash - * command register. Need 2 Write Pipeline Terminates to complete send. - */ -static void DoC_Command(void __iomem * docptr, unsigned char command, - unsigned char xtraflags) -{ - WriteDOC(command, docptr, Mplus_FlashCmd); - WriteDOC(command, docptr, Mplus_WritePipeTerm); - WriteDOC(command, docptr, Mplus_WritePipeTerm); -} - -/* DoC_Address: Set the current address for the flash chip through the Flash - * Address register. Need 2 Write Pipeline Terminates to complete send. - */ -static inline void DoC_Address(struct DiskOnChip *doc, int numbytes, - unsigned long ofs, unsigned char xtraflags1, - unsigned char xtraflags2) -{ - void __iomem * docptr = doc->virtadr; - - /* Allow for possible Mill Plus internal flash interleaving */ - ofs >>= doc->interleave; - - switch (numbytes) { - case 1: - /* Send single byte, bits 0-7. */ - WriteDOC(ofs & 0xff, docptr, Mplus_FlashAddress); - break; - case 2: - /* Send bits 9-16 followed by 17-23 */ - WriteDOC((ofs >> 9) & 0xff, docptr, Mplus_FlashAddress); - WriteDOC((ofs >> 17) & 0xff, docptr, Mplus_FlashAddress); - break; - case 3: - /* Send 0-7, 9-16, then 17-23 */ - WriteDOC(ofs & 0xff, docptr, Mplus_FlashAddress); - WriteDOC((ofs >> 9) & 0xff, docptr, Mplus_FlashAddress); - WriteDOC((ofs >> 17) & 0xff, docptr, Mplus_FlashAddress); - break; - default: - return; - } - - WriteDOC(0x00, docptr, Mplus_WritePipeTerm); - WriteDOC(0x00, docptr, Mplus_WritePipeTerm); -} - -/* DoC_SelectChip: Select a given flash chip within the current floor */ -static int DoC_SelectChip(void __iomem * docptr, int chip) -{ - /* No choice for flash chip on Millennium Plus */ - return 0; -} - -/* DoC_SelectFloor: Select a given floor (bank of flash chips) */ -static int DoC_SelectFloor(void __iomem * docptr, int floor) -{ - WriteDOC((floor & 0x3), docptr, Mplus_DeviceSelect); - return 0; -} - -/* - * Translate the given offset into the appropriate command and offset. - * This does the mapping using the 16bit interleave layout defined by - * M-Systems, and looks like this for a sector pair: - * +-----------+-------+-------+-------+--------------+---------+-----------+ - * | 0 --- 511 |512-517|518-519|520-521| 522 --- 1033 |1034-1039|1040 - 1055| - * +-----------+-------+-------+-------+--------------+---------+-----------+ - * | Data 0 | ECC 0 |Flags0 |Flags1 | Data 1 |ECC 1 | OOB 1 + 2 | - * +-----------+-------+-------+-------+--------------+---------+-----------+ - */ -/* FIXME: This lives in INFTL not here. Other users of flash devices - may not want it */ -static unsigned int DoC_GetDataOffset(struct mtd_info *mtd, loff_t *from) -{ - struct DiskOnChip *this = mtd->priv; - - if (this->interleave) { - unsigned int ofs = *from & 0x3ff; - unsigned int cmd; - - if (ofs < 512) { - cmd = NAND_CMD_READ0; - ofs &= 0x1ff; - } else if (ofs < 1014) { - cmd = NAND_CMD_READ1; - ofs = (ofs & 0x1ff) + 10; - } else { - cmd = NAND_CMD_READOOB; - ofs = ofs - 1014; - } - - *from = (*from & ~0x3ff) | ofs; - return cmd; - } else { - /* No interleave */ - if ((*from) & 0x100) - return NAND_CMD_READ1; - return NAND_CMD_READ0; - } -} - -static unsigned int DoC_GetECCOffset(struct mtd_info *mtd, loff_t *from) -{ - unsigned int ofs, cmd; - - if (*from & 0x200) { - cmd = NAND_CMD_READOOB; - ofs = 10 + (*from & 0xf); - } else { - cmd = NAND_CMD_READ1; - ofs = (*from & 0xf); - } - - *from = (*from & ~0x3ff) | ofs; - return cmd; -} - -static unsigned int DoC_GetFlagsOffset(struct mtd_info *mtd, loff_t *from) -{ - unsigned int ofs, cmd; - - cmd = NAND_CMD_READ1; - ofs = (*from & 0x200) ? 8 : 6; - *from = (*from & ~0x3ff) | ofs; - return cmd; -} - -static unsigned int DoC_GetHdrOffset(struct mtd_info *mtd, loff_t *from) -{ - unsigned int ofs, cmd; - - cmd = NAND_CMD_READOOB; - ofs = (*from & 0x200) ? 24 : 16; - *from = (*from & ~0x3ff) | ofs; - return cmd; -} - -static inline void MemReadDOC(void __iomem * docptr, unsigned char *buf, int len) -{ -#ifndef USE_MEMCPY - int i; - for (i = 0; i < len; i++) - buf[i] = ReadDOC(docptr, Mil_CDSN_IO + i); -#else - memcpy_fromio(buf, docptr + DoC_Mil_CDSN_IO, len); -#endif -} - -static inline void MemWriteDOC(void __iomem * docptr, unsigned char *buf, int len) -{ -#ifndef USE_MEMCPY - int i; - for (i = 0; i < len; i++) - WriteDOC(buf[i], docptr, Mil_CDSN_IO + i); -#else - memcpy_toio(docptr + DoC_Mil_CDSN_IO, buf, len); -#endif -} - -/* DoC_IdentChip: Identify a given NAND chip given {floor,chip} */ -static int DoC_IdentChip(struct DiskOnChip *doc, int floor, int chip) -{ - int mfr, id, i, j; - volatile char dummy; - void __iomem * docptr = doc->virtadr; - - /* Page in the required floor/chip */ - DoC_SelectFloor(docptr, floor); - DoC_SelectChip(docptr, chip); - - /* Millennium Plus bus cycle sequence as per figure 2, section 2.4 */ - WriteDOC((DOC_FLASH_CE | DOC_FLASH_WP), docptr, Mplus_FlashSelect); - - /* Reset the chip, see Software Requirement 11.4 item 1. */ - DoC_Command(docptr, NAND_CMD_RESET, 0); - DoC_WaitReady(docptr); - - /* Read the NAND chip ID: 1. Send ReadID command */ - DoC_Command(docptr, NAND_CMD_READID, 0); - - /* Read the NAND chip ID: 2. Send address byte zero */ - DoC_Address(doc, 1, 0x00, 0, 0x00); - - WriteDOC(0, docptr, Mplus_FlashControl); - DoC_WaitReady(docptr); - - /* Read the manufacturer and device id codes of the flash device through - CDSN IO register see Software Requirement 11.4 item 5.*/ - dummy = ReadDOC(docptr, Mplus_ReadPipeInit); - dummy = ReadDOC(docptr, Mplus_ReadPipeInit); - - mfr = ReadDOC(docptr, Mil_CDSN_IO); - if (doc->interleave) - dummy = ReadDOC(docptr, Mil_CDSN_IO); /* 2 way interleave */ - - id = ReadDOC(docptr, Mil_CDSN_IO); - if (doc->interleave) - dummy = ReadDOC(docptr, Mil_CDSN_IO); /* 2 way interleave */ - - dummy = ReadDOC(docptr, Mplus_LastDataRead); - dummy = ReadDOC(docptr, Mplus_LastDataRead); - - /* Disable flash internally */ - WriteDOC(0, docptr, Mplus_FlashSelect); - - /* No response - return failure */ - if (mfr == 0xff || mfr == 0) - return 0; - - for (i = 0; nand_flash_ids[i].name != NULL; i++) { - if (id == nand_flash_ids[i].id) { - /* Try to identify manufacturer */ - for (j = 0; nand_manuf_ids[j].id != 0x0; j++) { - if (nand_manuf_ids[j].id == mfr) - break; - } - printk(KERN_INFO "Flash chip found: Manufacturer ID: %2.2X, " - "Chip ID: %2.2X (%s:%s)\n", mfr, id, - nand_manuf_ids[j].name, nand_flash_ids[i].name); - doc->mfr = mfr; - doc->id = id; - doc->chipshift = ffs((nand_flash_ids[i].chipsize << 20)) - 1; - doc->erasesize = nand_flash_ids[i].erasesize << doc->interleave; - break; - } - } - - if (nand_flash_ids[i].name == NULL) - return 0; - return 1; -} - -/* DoC_ScanChips: Find all NAND chips present in a DiskOnChip, and identify them */ -static void DoC_ScanChips(struct DiskOnChip *this) -{ - int floor, chip; - int numchips[MAX_FLOORS_MPLUS]; - int ret; - - this->numchips = 0; - this->mfr = 0; - this->id = 0; - - /* Work out the intended interleave setting */ - this->interleave = 0; - if (this->ChipID == DOC_ChipID_DocMilPlus32) - this->interleave = 1; - - /* Check the ASIC agrees */ - if ( (this->interleave << 2) != - (ReadDOC(this->virtadr, Mplus_Configuration) & 4)) { - u_char conf = ReadDOC(this->virtadr, Mplus_Configuration); - printk(KERN_NOTICE "Setting DiskOnChip Millennium Plus interleave to %s\n", - this->interleave?"on (16-bit)":"off (8-bit)"); - conf ^= 4; - WriteDOC(conf, this->virtadr, Mplus_Configuration); - } - - /* For each floor, find the number of valid chips it contains */ - for (floor = 0,ret = 1; floor < MAX_FLOORS_MPLUS; floor++) { - numchips[floor] = 0; - for (chip = 0; chip < MAX_CHIPS_MPLUS && ret != 0; chip++) { - ret = DoC_IdentChip(this, floor, chip); - if (ret) { - numchips[floor]++; - this->numchips++; - } - } - } - /* If there are none at all that we recognise, bail */ - if (!this->numchips) { - printk("No flash chips recognised.\n"); - return; - } - - /* Allocate an array to hold the information for each chip */ - this->chips = kmalloc(sizeof(struct Nand) * this->numchips, GFP_KERNEL); - if (!this->chips){ - printk("MTD: No memory for allocating chip info structures\n"); - return; - } - - /* Fill out the chip array with {floor, chipno} for each - * detected chip in the device. */ - for (floor = 0, ret = 0; floor < MAX_FLOORS_MPLUS; floor++) { - for (chip = 0 ; chip < numchips[floor] ; chip++) { - this->chips[ret].floor = floor; - this->chips[ret].chip = chip; - this->chips[ret].curadr = 0; - this->chips[ret].curmode = 0x50; - ret++; - } - } - - /* Calculate and print the total size of the device */ - this->totlen = this->numchips * (1 << this->chipshift); - printk(KERN_INFO "%d flash chips found. Total DiskOnChip size: %ld MiB\n", - this->numchips ,this->totlen >> 20); -} - -static int DoCMilPlus_is_alias(struct DiskOnChip *doc1, struct DiskOnChip *doc2) -{ - int tmp1, tmp2, retval; - - if (doc1->physadr == doc2->physadr) - return 1; - - /* Use the alias resolution register which was set aside for this - * purpose. If it's value is the same on both chips, they might - * be the same chip, and we write to one and check for a change in - * the other. It's unclear if this register is usuable in the - * DoC 2000 (it's in the Millennium docs), but it seems to work. */ - tmp1 = ReadDOC(doc1->virtadr, Mplus_AliasResolution); - tmp2 = ReadDOC(doc2->virtadr, Mplus_AliasResolution); - if (tmp1 != tmp2) - return 0; - - WriteDOC((tmp1+1) % 0xff, doc1->virtadr, Mplus_AliasResolution); - tmp2 = ReadDOC(doc2->virtadr, Mplus_AliasResolution); - if (tmp2 == (tmp1+1) % 0xff) - retval = 1; - else - retval = 0; - - /* Restore register contents. May not be necessary, but do it just to - * be safe. */ - WriteDOC(tmp1, doc1->virtadr, Mplus_AliasResolution); - - return retval; -} - -/* This routine is found from the docprobe code by symbol_get(), - * which will bump the use count of this module. */ -void DoCMilPlus_init(struct mtd_info *mtd) -{ - struct DiskOnChip *this = mtd->priv; - struct DiskOnChip *old = NULL; - - /* We must avoid being called twice for the same device. */ - if (docmilpluslist) - old = docmilpluslist->priv; - - while (old) { - if (DoCMilPlus_is_alias(this, old)) { - printk(KERN_NOTICE "Ignoring DiskOnChip Millennium " - "Plus at 0x%lX - already configured\n", - this->physadr); - iounmap(this->virtadr); - kfree(mtd); - return; - } - if (old->nextdoc) - old = old->nextdoc->priv; - else - old = NULL; - } - - mtd->name = "DiskOnChip Millennium Plus"; - printk(KERN_NOTICE "DiskOnChip Millennium Plus found at " - "address 0x%lX\n", this->physadr); - - mtd->type = MTD_NANDFLASH; - mtd->flags = MTD_CAP_NANDFLASH; - mtd->writesize = 512; - mtd->oobsize = 16; - mtd->owner = THIS_MODULE; - mtd->erase = doc_erase; - mtd->read = doc_read; - mtd->write = doc_write; - mtd->read_oob = doc_read_oob; - mtd->write_oob = doc_write_oob; - this->curfloor = -1; - this->curchip = -1; - - /* Ident all the chips present. */ - DoC_ScanChips(this); - - if (!this->totlen) { - kfree(mtd); - iounmap(this->virtadr); - } else { - this->nextdoc = docmilpluslist; - docmilpluslist = mtd; - mtd->size = this->totlen; - mtd->erasesize = this->erasesize; - mtd_device_register(mtd, NULL, 0); - return; - } -} -EXPORT_SYMBOL_GPL(DoCMilPlus_init); - -#if 0 -static int doc_dumpblk(struct mtd_info *mtd, loff_t from) -{ - int i; - loff_t fofs; - struct DiskOnChip *this = mtd->priv; - void __iomem * docptr = this->virtadr; - struct Nand *mychip = &this->chips[from >> (this->chipshift)]; - unsigned char *bp, buf[1056]; - char c[32]; - - from &= ~0x3ff; - - /* Don't allow read past end of device */ - if (from >= this->totlen) - return -EINVAL; - - DoC_CheckASIC(docptr); - - /* Find the chip which is to be used and select it */ - if (this->curfloor != mychip->floor) { - DoC_SelectFloor(docptr, mychip->floor); - DoC_SelectChip(docptr, mychip->chip); - } else if (this->curchip != mychip->chip) { - DoC_SelectChip(docptr, mychip->chip); - } - this->curfloor = mychip->floor; - this->curchip = mychip->chip; - - /* Millennium Plus bus cycle sequence as per figure 2, section 2.4 */ - WriteDOC((DOC_FLASH_CE | DOC_FLASH_WP), docptr, Mplus_FlashSelect); - - /* Reset the chip, see Software Requirement 11.4 item 1. */ - DoC_Command(docptr, NAND_CMD_RESET, 0); - DoC_WaitReady(docptr); - - fofs = from; - DoC_Command(docptr, DoC_GetDataOffset(mtd, &fofs), 0); - DoC_Address(this, 3, fofs, 0, 0x00); - WriteDOC(0, docptr, Mplus_FlashControl); - DoC_WaitReady(docptr); - - /* disable the ECC engine */ - WriteDOC(DOC_ECC_RESET, docptr, Mplus_ECCConf); - - ReadDOC(docptr, Mplus_ReadPipeInit); - ReadDOC(docptr, Mplus_ReadPipeInit); - - /* Read the data via the internal pipeline through CDSN IO - register, see Pipelined Read Operations 11.3 */ - MemReadDOC(docptr, buf, 1054); - buf[1054] = ReadDOC(docptr, Mplus_LastDataRead); - buf[1055] = ReadDOC(docptr, Mplus_LastDataRead); - - memset(&c[0], 0, sizeof(c)); - printk("DUMP OFFSET=%x:\n", (int)from); - - for (i = 0, bp = &buf[0]; (i < 1056); i++) { - if ((i % 16) == 0) - printk("%08x: ", i); - printk(" %02x", *bp); - c[(i & 0xf)] = ((*bp >= 0x20) && (*bp <= 0x7f)) ? *bp : '.'; - bp++; - if (((i + 1) % 16) == 0) - printk(" %s\n", c); - } - printk("\n"); - - /* Disable flash internally */ - WriteDOC(0, docptr, Mplus_FlashSelect); - - return 0; -} -#endif - -static int doc_read(struct mtd_info *mtd, loff_t from, size_t len, - size_t *retlen, u_char *buf) -{ - int ret, i; - volatile char dummy; - loff_t fofs; - unsigned char syndrome[6], eccbuf[6]; - struct DiskOnChip *this = mtd->priv; - void __iomem * docptr = this->virtadr; - struct Nand *mychip = &this->chips[from >> (this->chipshift)]; - - /* Don't allow read past end of device */ - if (from >= this->totlen) - return -EINVAL; - - /* Don't allow a single read to cross a 512-byte block boundary */ - if (from + len > ((from | 0x1ff) + 1)) - len = ((from | 0x1ff) + 1) - from; - - DoC_CheckASIC(docptr); - - /* Find the chip which is to be used and select it */ - if (this->curfloor != mychip->floor) { - DoC_SelectFloor(docptr, mychip->floor); - DoC_SelectChip(docptr, mychip->chip); - } else if (this->curchip != mychip->chip) { - DoC_SelectChip(docptr, mychip->chip); - } - this->curfloor = mychip->floor; - this->curchip = mychip->chip; - - /* Millennium Plus bus cycle sequence as per figure 2, section 2.4 */ - WriteDOC((DOC_FLASH_CE | DOC_FLASH_WP), docptr, Mplus_FlashSelect); - - /* Reset the chip, see Software Requirement 11.4 item 1. */ - DoC_Command(docptr, NAND_CMD_RESET, 0); - DoC_WaitReady(docptr); - - fofs = from; - DoC_Command(docptr, DoC_GetDataOffset(mtd, &fofs), 0); - DoC_Address(this, 3, fofs, 0, 0x00); - WriteDOC(0, docptr, Mplus_FlashControl); - DoC_WaitReady(docptr); - - /* init the ECC engine, see Reed-Solomon EDC/ECC 11.1 .*/ - WriteDOC(DOC_ECC_RESET, docptr, Mplus_ECCConf); - WriteDOC(DOC_ECC_EN, docptr, Mplus_ECCConf); - - /* Let the caller know we completed it */ - *retlen = len; - ret = 0; - - ReadDOC(docptr, Mplus_ReadPipeInit); - ReadDOC(docptr, Mplus_ReadPipeInit); - - /* Read the data via the internal pipeline through CDSN IO - register, see Pipelined Read Operations 11.3 */ - MemReadDOC(docptr, buf, len); - - /* Read the ECC data following raw data */ - MemReadDOC(docptr, eccbuf, 4); - eccbuf[4] = ReadDOC(docptr, Mplus_LastDataRead); - eccbuf[5] = ReadDOC(docptr, Mplus_LastDataRead); - - /* Flush the pipeline */ - dummy = ReadDOC(docptr, Mplus_ECCConf); - dummy = ReadDOC(docptr, Mplus_ECCConf); - - /* Check the ECC Status */ - if (ReadDOC(docptr, Mplus_ECCConf) & 0x80) { - int nb_errors; - /* There was an ECC error */ -#ifdef ECC_DEBUG - printk("DiskOnChip ECC Error: Read at %lx\n", (long)from); -#endif - /* Read the ECC syndrome through the DiskOnChip ECC logic. - These syndrome will be all ZERO when there is no error */ - for (i = 0; i < 6; i++) - syndrome[i] = ReadDOC(docptr, Mplus_ECCSyndrome0 + i); - - nb_errors = doc_decode_ecc(buf, syndrome); -#ifdef ECC_DEBUG - printk("ECC Errors corrected: %x\n", nb_errors); -#endif - if (nb_errors < 0) { - /* We return error, but have actually done the - read. Not that this can be told to user-space, via - sys_read(), but at least MTD-aware stuff can know - about it by checking *retlen */ -#ifdef ECC_DEBUG - printk("%s(%d): Millennium Plus ECC error (from=0x%x:\n", - __FILE__, __LINE__, (int)from); - printk(" syndrome= %02x:%02x:%02x:%02x:%02x:" - "%02x\n", - syndrome[0], syndrome[1], syndrome[2], - syndrome[3], syndrome[4], syndrome[5]); - printk(" eccbuf= %02x:%02x:%02x:%02x:%02x:" - "%02x\n", - eccbuf[0], eccbuf[1], eccbuf[2], - eccbuf[3], eccbuf[4], eccbuf[5]); -#endif - ret = -EIO; - } - } - -#ifdef PSYCHO_DEBUG - printk("ECC DATA at %lx: %2.2X %2.2X %2.2X %2.2X %2.2X %2.2X\n", - (long)from, eccbuf[0], eccbuf[1], eccbuf[2], eccbuf[3], - eccbuf[4], eccbuf[5]); -#endif - /* disable the ECC engine */ - WriteDOC(DOC_ECC_DIS, docptr , Mplus_ECCConf); - - /* Disable flash internally */ - WriteDOC(0, docptr, Mplus_FlashSelect); - - return ret; -} - -static int doc_write(struct mtd_info *mtd, loff_t to, size_t len, - size_t *retlen, const u_char *buf) -{ - int i, before, ret = 0; - loff_t fto; - volatile char dummy; - char eccbuf[6]; - struct DiskOnChip *this = mtd->priv; - void __iomem * docptr = this->virtadr; - struct Nand *mychip = &this->chips[to >> (this->chipshift)]; - - /* Don't allow write past end of device */ - if (to >= this->totlen) - return -EINVAL; - - /* Don't allow writes which aren't exactly one block (512 bytes) */ - if ((to & 0x1ff) || (len != 0x200)) - return -EINVAL; - - /* Determine position of OOB flags, before or after data */ - before = (this->interleave && (to & 0x200)); - - DoC_CheckASIC(docptr); - - /* Find the chip which is to be used and select it */ - if (this->curfloor != mychip->floor) { - DoC_SelectFloor(docptr, mychip->floor); - DoC_SelectChip(docptr, mychip->chip); - } else if (this->curchip != mychip->chip) { - DoC_SelectChip(docptr, mychip->chip); - } - this->curfloor = mychip->floor; - this->curchip = mychip->chip; - - /* Millennium Plus bus cycle sequence as per figure 2, section 2.4 */ - WriteDOC(DOC_FLASH_CE, docptr, Mplus_FlashSelect); - - /* Reset the chip, see Software Requirement 11.4 item 1. */ - DoC_Command(docptr, NAND_CMD_RESET, 0); - DoC_WaitReady(docptr); - - /* Set device to appropriate plane of flash */ - fto = to; - WriteDOC(DoC_GetDataOffset(mtd, &fto), docptr, Mplus_FlashCmd); - - /* On interleaved devices the flags for 2nd half 512 are before data */ - if (before) - fto -= 2; - - /* issue the Serial Data In command to initial the Page Program process */ - DoC_Command(docptr, NAND_CMD_SEQIN, 0x00); - DoC_Address(this, 3, fto, 0x00, 0x00); - - /* Disable the ECC engine */ - WriteDOC(DOC_ECC_RESET, docptr, Mplus_ECCConf); - - if (before) { - /* Write the block status BLOCK_USED (0x5555) */ - WriteDOC(0x55, docptr, Mil_CDSN_IO); - WriteDOC(0x55, docptr, Mil_CDSN_IO); - } - - /* init the ECC engine, see Reed-Solomon EDC/ECC 11.1 .*/ - WriteDOC(DOC_ECC_EN | DOC_ECC_RW, docptr, Mplus_ECCConf); - - MemWriteDOC(docptr, (unsigned char *) buf, len); - - /* Write ECC data to flash, the ECC info is generated by - the DiskOnChip ECC logic see Reed-Solomon EDC/ECC 11.1 */ - DoC_Delay(docptr, 3); - - /* Read the ECC data through the DiskOnChip ECC logic */ - for (i = 0; i < 6; i++) - eccbuf[i] = ReadDOC(docptr, Mplus_ECCSyndrome0 + i); - - /* disable the ECC engine */ - WriteDOC(DOC_ECC_DIS, docptr, Mplus_ECCConf); - - /* Write the ECC data to flash */ - MemWriteDOC(docptr, eccbuf, 6); - - if (!before) { - /* Write the block status BLOCK_USED (0x5555) */ - WriteDOC(0x55, docptr, Mil_CDSN_IO+6); - WriteDOC(0x55, docptr, Mil_CDSN_IO+7); - } - -#ifdef PSYCHO_DEBUG - printk("OOB data at %lx is %2.2X %2.2X %2.2X %2.2X %2.2X %2.2X\n", - (long) to, eccbuf[0], eccbuf[1], eccbuf[2], eccbuf[3], - eccbuf[4], eccbuf[5]); -#endif - - WriteDOC(0x00, docptr, Mplus_WritePipeTerm); - WriteDOC(0x00, docptr, Mplus_WritePipeTerm); - - /* Commit the Page Program command and wait for ready - see Software Requirement 11.4 item 1.*/ - DoC_Command(docptr, NAND_CMD_PAGEPROG, 0x00); - DoC_WaitReady(docptr); - - /* Read the status of the flash device through CDSN IO register - see Software Requirement 11.4 item 5.*/ - DoC_Command(docptr, NAND_CMD_STATUS, 0); - dummy = ReadDOC(docptr, Mplus_ReadPipeInit); - dummy = ReadDOC(docptr, Mplus_ReadPipeInit); - DoC_Delay(docptr, 2); - if ((dummy = ReadDOC(docptr, Mplus_LastDataRead)) & 1) { - printk("MTD: Error 0x%x programming at 0x%x\n", dummy, (int)to); - /* Error in programming - FIXME: implement Bad Block Replacement (in nftl.c ??) */ - *retlen = 0; - ret = -EIO; - } - dummy = ReadDOC(docptr, Mplus_LastDataRead); - - /* Disable flash internally */ - WriteDOC(0, docptr, Mplus_FlashSelect); - - /* Let the caller know we completed it */ - *retlen = len; - - return ret; -} - -static int doc_read_oob(struct mtd_info *mtd, loff_t ofs, - struct mtd_oob_ops *ops) -{ - loff_t fofs, base; - struct DiskOnChip *this = mtd->priv; - void __iomem * docptr = this->virtadr; - struct Nand *mychip = &this->chips[ofs >> this->chipshift]; - size_t i, size, got, want; - uint8_t *buf = ops->oobbuf; - size_t len = ops->len; - - BUG_ON(ops->mode != MTD_OPS_PLACE_OOB); - - ofs += ops->ooboffs; - - DoC_CheckASIC(docptr); - - /* Find the chip which is to be used and select it */ - if (this->curfloor != mychip->floor) { - DoC_SelectFloor(docptr, mychip->floor); - DoC_SelectChip(docptr, mychip->chip); - } else if (this->curchip != mychip->chip) { - DoC_SelectChip(docptr, mychip->chip); - } - this->curfloor = mychip->floor; - this->curchip = mychip->chip; - - /* Millennium Plus bus cycle sequence as per figure 2, section 2.4 */ - WriteDOC((DOC_FLASH_CE | DOC_FLASH_WP), docptr, Mplus_FlashSelect); - - /* disable the ECC engine */ - WriteDOC(DOC_ECC_RESET, docptr, Mplus_ECCConf); - DoC_WaitReady(docptr); - - /* Maximum of 16 bytes in the OOB region, so limit read to that */ - if (len > 16) - len = 16; - got = 0; - want = len; - - for (i = 0; ((i < 3) && (want > 0)); i++) { - /* Figure out which region we are accessing... */ - fofs = ofs; - base = ofs & 0xf; - if (!this->interleave) { - DoC_Command(docptr, NAND_CMD_READOOB, 0); - size = 16 - base; - } else if (base < 6) { - DoC_Command(docptr, DoC_GetECCOffset(mtd, &fofs), 0); - size = 6 - base; - } else if (base < 8) { - DoC_Command(docptr, DoC_GetFlagsOffset(mtd, &fofs), 0); - size = 8 - base; - } else { - DoC_Command(docptr, DoC_GetHdrOffset(mtd, &fofs), 0); - size = 16 - base; - } - if (size > want) - size = want; - - /* Issue read command */ - DoC_Address(this, 3, fofs, 0, 0x00); - WriteDOC(0, docptr, Mplus_FlashControl); - DoC_WaitReady(docptr); - - ReadDOC(docptr, Mplus_ReadPipeInit); - ReadDOC(docptr, Mplus_ReadPipeInit); - MemReadDOC(docptr, &buf[got], size - 2); - buf[got + size - 2] = ReadDOC(docptr, Mplus_LastDataRead); - buf[got + size - 1] = ReadDOC(docptr, Mplus_LastDataRead); - - ofs += size; - got += size; - want -= size; - } - - /* Disable flash internally */ - WriteDOC(0, docptr, Mplus_FlashSelect); - - ops->retlen = len; - return 0; -} - -static int doc_write_oob(struct mtd_info *mtd, loff_t ofs, - struct mtd_oob_ops *ops) -{ - volatile char dummy; - loff_t fofs, base; - struct DiskOnChip *this = mtd->priv; - void __iomem * docptr = this->virtadr; - struct Nand *mychip = &this->chips[ofs >> this->chipshift]; - size_t i, size, got, want; - int ret = 0; - uint8_t *buf = ops->oobbuf; - size_t len = ops->len; - - BUG_ON(ops->mode != MTD_OPS_PLACE_OOB); - - ofs += ops->ooboffs; - - DoC_CheckASIC(docptr); - - /* Find the chip which is to be used and select it */ - if (this->curfloor != mychip->floor) { - DoC_SelectFloor(docptr, mychip->floor); - DoC_SelectChip(docptr, mychip->chip); - } else if (this->curchip != mychip->chip) { - DoC_SelectChip(docptr, mychip->chip); - } - this->curfloor = mychip->floor; - this->curchip = mychip->chip; - - /* Millennium Plus bus cycle sequence as per figure 2, section 2.4 */ - WriteDOC(DOC_FLASH_CE, docptr, Mplus_FlashSelect); - - - /* Maximum of 16 bytes in the OOB region, so limit write to that */ - if (len > 16) - len = 16; - got = 0; - want = len; - - for (i = 0; ((i < 3) && (want > 0)); i++) { - /* Reset the chip, see Software Requirement 11.4 item 1. */ - DoC_Command(docptr, NAND_CMD_RESET, 0); - DoC_WaitReady(docptr); - - /* Figure out which region we are accessing... */ - fofs = ofs; - base = ofs & 0x0f; - if (!this->interleave) { - WriteDOC(NAND_CMD_READOOB, docptr, Mplus_FlashCmd); - size = 16 - base; - } else if (base < 6) { - WriteDOC(DoC_GetECCOffset(mtd, &fofs), docptr, Mplus_FlashCmd); - size = 6 - base; - } else if (base < 8) { - WriteDOC(DoC_GetFlagsOffset(mtd, &fofs), docptr, Mplus_FlashCmd); - size = 8 - base; - } else { - WriteDOC(DoC_GetHdrOffset(mtd, &fofs), docptr, Mplus_FlashCmd); - size = 16 - base; - } - if (size > want) - size = want; - - /* Issue the Serial Data In command to initial the Page Program process */ - DoC_Command(docptr, NAND_CMD_SEQIN, 0x00); - DoC_Address(this, 3, fofs, 0, 0x00); - - /* Disable the ECC engine */ - WriteDOC(DOC_ECC_RESET, docptr, Mplus_ECCConf); - - /* Write the data via the internal pipeline through CDSN IO - register, see Pipelined Write Operations 11.2 */ - MemWriteDOC(docptr, (unsigned char *) &buf[got], size); - WriteDOC(0x00, docptr, Mplus_WritePipeTerm); - WriteDOC(0x00, docptr, Mplus_WritePipeTerm); - - /* Commit the Page Program command and wait for ready - see Software Requirement 11.4 item 1.*/ - DoC_Command(docptr, NAND_CMD_PAGEPROG, 0x00); - DoC_WaitReady(docptr); - - /* Read the status of the flash device through CDSN IO register - see Software Requirement 11.4 item 5.*/ - DoC_Command(docptr, NAND_CMD_STATUS, 0x00); - dummy = ReadDOC(docptr, Mplus_ReadPipeInit); - dummy = ReadDOC(docptr, Mplus_ReadPipeInit); - DoC_Delay(docptr, 2); - if ((dummy = ReadDOC(docptr, Mplus_LastDataRead)) & 1) { - printk("MTD: Error 0x%x programming oob at 0x%x\n", - dummy, (int)ofs); - /* FIXME: implement Bad Block Replacement */ - ops->retlen = 0; - ret = -EIO; - } - dummy = ReadDOC(docptr, Mplus_LastDataRead); - - ofs += size; - got += size; - want -= size; - } - - /* Disable flash internally */ - WriteDOC(0, docptr, Mplus_FlashSelect); - - ops->retlen = len; - return ret; -} - -int doc_erase(struct mtd_info *mtd, struct erase_info *instr) -{ - volatile char dummy; - struct DiskOnChip *this = mtd->priv; - __u32 ofs = instr->addr; - __u32 len = instr->len; - void __iomem * docptr = this->virtadr; - struct Nand *mychip = &this->chips[ofs >> this->chipshift]; - - DoC_CheckASIC(docptr); - - if (len != mtd->erasesize) - printk(KERN_WARNING "MTD: Erase not right size (%x != %x)n", - len, mtd->erasesize); - - /* Find the chip which is to be used and select it */ - if (this->curfloor != mychip->floor) { - DoC_SelectFloor(docptr, mychip->floor); - DoC_SelectChip(docptr, mychip->chip); - } else if (this->curchip != mychip->chip) { - DoC_SelectChip(docptr, mychip->chip); - } - this->curfloor = mychip->floor; - this->curchip = mychip->chip; - - instr->state = MTD_ERASE_PENDING; - - /* Millennium Plus bus cycle sequence as per figure 2, section 2.4 */ - WriteDOC(DOC_FLASH_CE, docptr, Mplus_FlashSelect); - - DoC_Command(docptr, NAND_CMD_RESET, 0x00); - DoC_WaitReady(docptr); - - DoC_Command(docptr, NAND_CMD_ERASE1, 0); - DoC_Address(this, 2, ofs, 0, 0x00); - DoC_Command(docptr, NAND_CMD_ERASE2, 0); - DoC_WaitReady(docptr); - instr->state = MTD_ERASING; - - /* Read the status of the flash device through CDSN IO register - see Software Requirement 11.4 item 5. */ - DoC_Command(docptr, NAND_CMD_STATUS, 0); - dummy = ReadDOC(docptr, Mplus_ReadPipeInit); - dummy = ReadDOC(docptr, Mplus_ReadPipeInit); - if ((dummy = ReadDOC(docptr, Mplus_LastDataRead)) & 1) { - printk("MTD: Error 0x%x erasing at 0x%x\n", dummy, ofs); - /* FIXME: implement Bad Block Replacement (in nftl.c ??) */ - instr->state = MTD_ERASE_FAILED; - } else { - instr->state = MTD_ERASE_DONE; - } - dummy = ReadDOC(docptr, Mplus_LastDataRead); - - /* Disable flash internally */ - WriteDOC(0, docptr, Mplus_FlashSelect); - - mtd_erase_callback(instr); - - return 0; -} - -/**************************************************************************** - * - * Module stuff - * - ****************************************************************************/ - -static void __exit cleanup_doc2001plus(void) -{ - struct mtd_info *mtd; - struct DiskOnChip *this; - - while ((mtd=docmilpluslist)) { - this = mtd->priv; - docmilpluslist = this->nextdoc; - - mtd_device_unregister(mtd); - - iounmap(this->virtadr); - kfree(this->chips); - kfree(mtd); - } -} - -module_exit(cleanup_doc2001plus); - -MODULE_LICENSE("GPL"); -MODULE_AUTHOR("Greg Ungerer <gerg@snapgear.com> et al."); -MODULE_DESCRIPTION("Driver for DiskOnChip Millennium Plus"); diff --git a/drivers/mtd/devices/docecc.c b/drivers/mtd/devices/docecc.c deleted file mode 100644 index 4a1c39b6f37..00000000000 --- a/drivers/mtd/devices/docecc.c +++ /dev/null @@ -1,521 +0,0 @@ -/* - * ECC algorithm for M-systems disk on chip. We use the excellent Reed - * Solmon code of Phil Karn (karn@ka9q.ampr.org) available under the - * GNU GPL License. The rest is simply to convert the disk on chip - * syndrome into a standard syndome. - * - * Author: Fabrice Bellard (fabrice.bellard@netgem.com) - * Copyright (C) 2000 Netgem S.A. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ -#include <linux/kernel.h> -#include <linux/module.h> -#include <asm/errno.h> -#include <asm/io.h> -#include <asm/uaccess.h> -#include <linux/delay.h> -#include <linux/slab.h> -#include <linux/init.h> -#include <linux/types.h> - -#include <linux/mtd/mtd.h> -#include <linux/mtd/doc2000.h> - -#define DEBUG_ECC 0 -/* need to undef it (from asm/termbits.h) */ -#undef B0 - -#define MM 10 /* Symbol size in bits */ -#define KK (1023-4) /* Number of data symbols per block */ -#define B0 510 /* First root of generator polynomial, alpha form */ -#define PRIM 1 /* power of alpha used to generate roots of generator poly */ -#define NN ((1 << MM) - 1) - -typedef unsigned short dtype; - -/* 1+x^3+x^10 */ -static const int Pp[MM+1] = { 1, 0, 0, 1, 0, 0, 0, 0, 0, 0, 1 }; - -/* This defines the type used to store an element of the Galois Field - * used by the code. Make sure this is something larger than a char if - * if anything larger than GF(256) is used. - * - * Note: unsigned char will work up to GF(256) but int seems to run - * faster on the Pentium. - */ -typedef int gf; - -/* No legal value in index form represents zero, so - * we need a special value for this purpose - */ -#define A0 (NN) - -/* Compute x % NN, where NN is 2**MM - 1, - * without a slow divide - */ -static inline gf -modnn(int x) -{ - while (x >= NN) { - x -= NN; - x = (x >> MM) + (x & NN); - } - return x; -} - -#define CLEAR(a,n) {\ -int ci;\ -for(ci=(n)-1;ci >=0;ci--)\ -(a)[ci] = 0;\ -} - -#define COPY(a,b,n) {\ -int ci;\ -for(ci=(n)-1;ci >=0;ci--)\ -(a)[ci] = (b)[ci];\ -} - -#define COPYDOWN(a,b,n) {\ -int ci;\ -for(ci=(n)-1;ci >=0;ci--)\ -(a)[ci] = (b)[ci];\ -} - -#define Ldec 1 - -/* generate GF(2**m) from the irreducible polynomial p(X) in Pp[0]..Pp[m] - lookup tables: index->polynomial form alpha_to[] contains j=alpha**i; - polynomial form -> index form index_of[j=alpha**i] = i - alpha=2 is the primitive element of GF(2**m) - HARI's COMMENT: (4/13/94) alpha_to[] can be used as follows: - Let @ represent the primitive element commonly called "alpha" that - is the root of the primitive polynomial p(x). Then in GF(2^m), for any - 0 <= i <= 2^m-2, - @^i = a(0) + a(1) @ + a(2) @^2 + ... + a(m-1) @^(m-1) - where the binary vector (a(0),a(1),a(2),...,a(m-1)) is the representation - of the integer "alpha_to[i]" with a(0) being the LSB and a(m-1) the MSB. Thus for - example the polynomial representation of @^5 would be given by the binary - representation of the integer "alpha_to[5]". - Similarly, index_of[] can be used as follows: - As above, let @ represent the primitive element of GF(2^m) that is - the root of the primitive polynomial p(x). In order to find the power - of @ (alpha) that has the polynomial representation - a(0) + a(1) @ + a(2) @^2 + ... + a(m-1) @^(m-1) - we consider the integer "i" whose binary representation with a(0) being LSB - and a(m-1) MSB is (a(0),a(1),...,a(m-1)) and locate the entry - "index_of[i]". Now, @^index_of[i] is that element whose polynomial - representation is (a(0),a(1),a(2),...,a(m-1)). - NOTE: - The element alpha_to[2^m-1] = 0 always signifying that the - representation of "@^infinity" = 0 is (0,0,0,...,0). - Similarly, the element index_of[0] = A0 always signifying - that the power of alpha which has the polynomial representation - (0,0,...,0) is "infinity". - -*/ - -static void -generate_gf(dtype Alpha_to[NN + 1], dtype Index_of[NN + 1]) -{ - register int i, mask; - - mask = 1; - Alpha_to[MM] = 0; - for (i = 0; i < MM; i++) { - Alpha_to[i] = mask; - Index_of[Alpha_to[i]] = i; - /* If Pp[i] == 1 then, term @^i occurs in poly-repr of @^MM */ - if (Pp[i] != 0) - Alpha_to[MM] ^= mask; /* Bit-wise EXOR operation */ - mask <<= 1; /* single left-shift */ - } - Index_of[Alpha_to[MM]] = MM; - /* - * Have obtained poly-repr of @^MM. Poly-repr of @^(i+1) is given by - * poly-repr of @^i shifted left one-bit and accounting for any @^MM - * term that may occur when poly-repr of @^i is shifted. - */ - mask >>= 1; - for (i = MM + 1; i < NN; i++) { - if (Alpha_to[i - 1] >= mask) - Alpha_to[i] = Alpha_to[MM] ^ ((Alpha_to[i - 1] ^ mask) << 1); - else - Alpha_to[i] = Alpha_to[i - 1] << 1; - Index_of[Alpha_to[i]] = i; - } - Index_of[0] = A0; - Alpha_to[NN] = 0; -} - -/* - * Performs ERRORS+ERASURES decoding of RS codes. bb[] is the content - * of the feedback shift register after having processed the data and - * the ECC. - * - * Return number of symbols corrected, or -1 if codeword is illegal - * or uncorrectable. If eras_pos is non-null, the detected error locations - * are written back. NOTE! This array must be at least NN-KK elements long. - * The corrected data are written in eras_val[]. They must be xor with the data - * to retrieve the correct data : data[erase_pos[i]] ^= erase_val[i] . - * - * First "no_eras" erasures are declared by the calling program. Then, the - * maximum # of errors correctable is t_after_eras = floor((NN-KK-no_eras)/2). - * If the number of channel errors is not greater than "t_after_eras" the - * transmitted codeword will be recovered. Details of algorithm can be found - * in R. Blahut's "Theory ... of Error-Correcting Codes". - - * Warning: the eras_pos[] array must not contain duplicate entries; decoder failure - * will result. The decoder *could* check for this condition, but it would involve - * extra time on every decoding operation. - * */ -static int -eras_dec_rs(dtype Alpha_to[NN + 1], dtype Index_of[NN + 1], - gf bb[NN - KK + 1], gf eras_val[NN-KK], int eras_pos[NN-KK], - int no_eras) -{ - int deg_lambda, el, deg_omega; - int i, j, r,k; - gf u,q,tmp,num1,num2,den,discr_r; - gf lambda[NN-KK + 1], s[NN-KK + 1]; /* Err+Eras Locator poly - * and syndrome poly */ - gf b[NN-KK + 1], t[NN-KK + 1], omega[NN-KK + 1]; - gf root[NN-KK], reg[NN-KK + 1], loc[NN-KK]; - int syn_error, count; - - syn_error = 0; - for(i=0;i<NN-KK;i++) - syn_error |= bb[i]; - - if (!syn_error) { - /* if remainder is zero, data[] is a codeword and there are no - * errors to correct. So return data[] unmodified - */ - count = 0; - goto finish; - } - - for(i=1;i<=NN-KK;i++){ - s[i] = bb[0]; - } - for(j=1;j<NN-KK;j++){ - if(bb[j] == 0) - continue; - tmp = Index_of[bb[j]]; - - for(i=1;i<=NN-KK;i++) - s[i] ^= Alpha_to[modnn(tmp + (B0+i-1)*PRIM*j)]; - } - - /* undo the feedback register implicit multiplication and convert - syndromes to index form */ - - for(i=1;i<=NN-KK;i++) { - tmp = Index_of[s[i]]; - if (tmp != A0) - tmp = modnn(tmp + 2 * KK * (B0+i-1)*PRIM); - s[i] = tmp; - } - - CLEAR(&lambda[1],NN-KK); - lambda[0] = 1; - - if (no_eras > 0) { - /* Init lambda to be the erasure locator polynomial */ - lambda[1] = Alpha_to[modnn(PRIM * eras_pos[0])]; - for (i = 1; i < no_eras; i++) { - u = modnn(PRIM*eras_pos[i]); - for (j = i+1; j > 0; j--) { - tmp = Index_of[lambda[j - 1]]; - if(tmp != A0) - lambda[j] ^= Alpha_to[modnn(u + tmp)]; - } - } -#if DEBUG_ECC >= 1 - /* Test code that verifies the erasure locator polynomial just constructed - Needed only for decoder debugging. */ - - /* find roots of the erasure location polynomial */ - for(i=1;i<=no_eras;i++) - reg[i] = Index_of[lambda[i]]; - count = 0; - for (i = 1,k=NN-Ldec; i <= NN; i++,k = modnn(NN+k-Ldec)) { - q = 1; - for (j = 1; j <= no_eras; j++) - if (reg[j] != A0) { - reg[j] = modnn(reg[j] + j); - q ^= Alpha_to[reg[j]]; - } - if (q != 0) - continue; - /* store root and error location number indices */ - root[count] = i; - loc[count] = k; - count++; - } - if (count != no_eras) { - printf("\n lambda(x) is WRONG\n"); - count = -1; - goto finish; - } -#if DEBUG_ECC >= 2 - printf("\n Erasure positions as determined by roots of Eras Loc Poly:\n"); - for (i = 0; i < count; i++) - printf("%d ", loc[i]); - printf("\n"); -#endif -#endif - } - for(i=0;i<NN-KK+1;i++) - b[i] = Index_of[lambda[i]]; - - /* - * Begin Berlekamp-Massey algorithm to determine error+erasure - * locator polynomial - */ - r = no_eras; - el = no_eras; - while (++r <= NN-KK) { /* r is the step number */ - /* Compute discrepancy at the r-th step in poly-form */ - discr_r = 0; - for (i = 0; i < r; i++){ - if ((lambda[i] != 0) && (s[r - i] != A0)) { - discr_r ^= Alpha_to[modnn(Index_of[lambda[i]] + s[r - i])]; - } - } - discr_r = Index_of[discr_r]; /* Index form */ - if (discr_r == A0) { - /* 2 lines below: B(x) <-- x*B(x) */ - COPYDOWN(&b[1],b,NN-KK); - b[0] = A0; - } else { - /* 7 lines below: T(x) <-- lambda(x) - discr_r*x*b(x) */ - t[0] = lambda[0]; - for (i = 0 ; i < NN-KK; i++) { - if(b[i] != A0) - t[i+1] = lambda[i+1] ^ Alpha_to[modnn(discr_r + b[i])]; - else - t[i+1] = lambda[i+1]; - } - if (2 * el <= r + no_eras - 1) { - el = r + no_eras - el; - /* - * 2 lines below: B(x) <-- inv(discr_r) * - * lambda(x) - */ - for (i = 0; i <= NN-KK; i++) - b[i] = (lambda[i] == 0) ? A0 : modnn(Index_of[lambda[i]] - discr_r + NN); - } else { - /* 2 lines below: B(x) <-- x*B(x) */ - COPYDOWN(&b[1],b,NN-KK); - b[0] = A0; - } - COPY(lambda,t,NN-KK+1); - } - } - - /* Convert lambda to index form and compute deg(lambda(x)) */ - deg_lambda = 0; - for(i=0;i<NN-KK+1;i++){ - lambda[i] = Index_of[lambda[i]]; - if(lambda[i] != A0) - deg_lambda = i; - } - /* - * Find roots of the error+erasure locator polynomial by Chien - * Search - */ - COPY(®[1],&lambda[1],NN-KK); - count = 0; /* Number of roots of lambda(x) */ - for (i = 1,k=NN-Ldec; i <= NN; i++,k = modnn(NN+k-Ldec)) { - q = 1; - for (j = deg_lambda; j > 0; j--){ - if (reg[j] != A0) { - reg[j] = modnn(reg[j] + j); - q ^= Alpha_to[reg[j]]; - } - } - if (q != 0) - continue; - /* store root (index-form) and error location number */ - root[count] = i; - loc[count] = k; - /* If we've already found max possible roots, - * abort the search to save time - */ - if(++count == deg_lambda) - break; - } - if (deg_lambda != count) { - /* - * deg(lambda) unequal to number of roots => uncorrectable - * error detected - */ - count = -1; - goto finish; - } - /* - * Compute err+eras evaluator poly omega(x) = s(x)*lambda(x) (modulo - * x**(NN-KK)). in index form. Also find deg(omega). - */ - deg_omega = 0; - for (i = 0; i < NN-KK;i++){ - tmp = 0; - j = (deg_lambda < i) ? deg_lambda : i; - for(;j >= 0; j--){ - if ((s[i + 1 - j] != A0) && (lambda[j] != A0)) - tmp ^= Alpha_to[modnn(s[i + 1 - j] + lambda[j])]; - } - if(tmp != 0) - deg_omega = i; - omega[i] = Index_of[tmp]; - } - omega[NN-KK] = A0; - - /* - * Compute error values in poly-form. num1 = omega(inv(X(l))), num2 = - * inv(X(l))**(B0-1) and den = lambda_pr(inv(X(l))) all in poly-form - */ - for (j = count-1; j >=0; j--) { - num1 = 0; - for (i = deg_omega; i >= 0; i--) { - if (omega[i] != A0) - num1 ^= Alpha_to[modnn(omega[i] + i * root[j])]; - } - num2 = Alpha_to[modnn(root[j] * (B0 - 1) + NN)]; - den = 0; - - /* lambda[i+1] for i even is the formal derivative lambda_pr of lambda[i] */ - for (i = min(deg_lambda,NN-KK-1) & ~1; i >= 0; i -=2) { - if(lambda[i+1] != A0) - den ^= Alpha_to[modnn(lambda[i+1] + i * root[j])]; - } - if (den == 0) { -#if DEBUG_ECC >= 1 - printf("\n ERROR: denominator = 0\n"); -#endif - /* Convert to dual- basis */ - count = -1; - goto finish; - } - /* Apply error to data */ - if (num1 != 0) { - eras_val[j] = Alpha_to[modnn(Index_of[num1] + Index_of[num2] + NN - Index_of[den])]; - } else { - eras_val[j] = 0; - } - } - finish: - for(i=0;i<count;i++) - eras_pos[i] = loc[i]; - return count; -} - -/***************************************************************************/ -/* The DOC specific code begins here */ - -#define SECTOR_SIZE 512 -/* The sector bytes are packed into NB_DATA MM bits words */ -#define NB_DATA (((SECTOR_SIZE + 1) * 8 + 6) / MM) - -/* - * Correct the errors in 'sector[]' by using 'ecc1[]' which is the - * content of the feedback shift register applyied to the sector and - * the ECC. Return the number of errors corrected (and correct them in - * sector), or -1 if error - */ -int doc_decode_ecc(unsigned char sector[SECTOR_SIZE], unsigned char ecc1[6]) -{ - int parity, i, nb_errors; - gf bb[NN - KK + 1]; - gf error_val[NN-KK]; - int error_pos[NN-KK], pos, bitpos, index, val; - dtype *Alpha_to, *Index_of; - - /* init log and exp tables here to save memory. However, it is slower */ - Alpha_to = kmalloc((NN + 1) * sizeof(dtype), GFP_KERNEL); - if (!Alpha_to) - return -1; - - Index_of = kmalloc((NN + 1) * sizeof(dtype), GFP_KERNEL); - if (!Index_of) { - kfree(Alpha_to); - return -1; - } - - generate_gf(Alpha_to, Index_of); - - parity = ecc1[1]; - - bb[0] = (ecc1[4] & 0xff) | ((ecc1[5] & 0x03) << 8); - bb[1] = ((ecc1[5] & 0xfc) >> 2) | ((ecc1[2] & 0x0f) << 6); - bb[2] = ((ecc1[2] & 0xf0) >> 4) | ((ecc1[3] & 0x3f) << 4); - bb[3] = ((ecc1[3] & 0xc0) >> 6) | ((ecc1[0] & 0xff) << 2); - - nb_errors = eras_dec_rs(Alpha_to, Index_of, bb, - error_val, error_pos, 0); - if (nb_errors <= 0) - goto the_end; - - /* correct the errors */ - for(i=0;i<nb_errors;i++) { - pos = error_pos[i]; - if (pos >= NB_DATA && pos < KK) { - nb_errors = -1; - goto the_end; - } - if (pos < NB_DATA) { - /* extract bit position (MSB first) */ - pos = 10 * (NB_DATA - 1 - pos) - 6; - /* now correct the following 10 bits. At most two bytes - can be modified since pos is even */ - index = (pos >> 3) ^ 1; - bitpos = pos & 7; - if ((index >= 0 && index < SECTOR_SIZE) || - index == (SECTOR_SIZE + 1)) { - val = error_val[i] >> (2 + bitpos); - parity ^= val; - if (index < SECTOR_SIZE) - sector[index] ^= val; - } - index = ((pos >> 3) + 1) ^ 1; - bitpos = (bitpos + 10) & 7; - if (bitpos == 0) - bitpos = 8; - if ((index >= 0 && index < SECTOR_SIZE) || - index == (SECTOR_SIZE + 1)) { - val = error_val[i] << (8 - bitpos); - parity ^= val; - if (index < SECTOR_SIZE) - sector[index] ^= val; - } - } - } - - /* use parity to test extra errors */ - if ((parity & 0xff) != 0) - nb_errors = -1; - - the_end: - kfree(Alpha_to); - kfree(Index_of); - return nb_errors; -} - -EXPORT_SYMBOL_GPL(doc_decode_ecc); - -MODULE_LICENSE("GPL"); -MODULE_AUTHOR("Fabrice Bellard <fabrice.bellard@netgem.com>"); -MODULE_DESCRIPTION("ECC code for correcting errors detected by DiskOnChip 2000 and Millennium ECC hardware"); diff --git a/drivers/mtd/devices/docg3.c b/drivers/mtd/devices/docg3.c index ad11ef0a81f..91a169c44b3 100644 --- a/drivers/mtd/devices/docg3.c +++ b/drivers/mtd/devices/docg3.c @@ -80,14 +80,9 @@ static struct nand_ecclayout docg3_oobinfo = { .oobavail = 8, }; -/** - * struct docg3_bch - BCH engine - */ -static struct bch_control *docg3_bch; - static inline u8 doc_readb(struct docg3 *docg3, u16 reg) { - u8 val = readb(docg3->base + reg); + u8 val = readb(docg3->cascade->base + reg); trace_docg3_io(0, 8, reg, (int)val); return val; @@ -95,7 +90,7 @@ static inline u8 doc_readb(struct docg3 *docg3, u16 reg) static inline u16 doc_readw(struct docg3 *docg3, u16 reg) { - u16 val = readw(docg3->base + reg); + u16 val = readw(docg3->cascade->base + reg); trace_docg3_io(0, 16, reg, (int)val); return val; @@ -103,13 +98,13 @@ static inline u16 doc_readw(struct docg3 *docg3, u16 reg) static inline void doc_writeb(struct docg3 *docg3, u8 val, u16 reg) { - writeb(val, docg3->base + reg); + writeb(val, docg3->cascade->base + reg); trace_docg3_io(1, 8, reg, val); } static inline void doc_writew(struct docg3 *docg3, u16 val, u16 reg) { - writew(val, docg3->base + reg); + writew(val, docg3->cascade->base + reg); trace_docg3_io(1, 16, reg, val); } @@ -128,7 +123,7 @@ static inline void doc_flash_address(struct docg3 *docg3, u8 addr) doc_writeb(docg3, addr, DOC_FLASHADDRESS); } -static char const *part_probes[] = { "cmdlinepart", "saftlpart", NULL }; +static char const * const part_probes[] = { "cmdlinepart", "saftlpart", NULL }; static int doc_register_readb(struct docg3 *docg3, int reg) { @@ -232,7 +227,7 @@ static void doc_read_data_area(struct docg3 *docg3, void *buf, int len, u8 data8, *dst8; doc_dbg("doc_read_data_area(buf=%p, len=%d)\n", buf, len); - cdr = len & 0x3; + cdr = len & 0x1; len4 = len - cdr; if (first) @@ -388,7 +383,7 @@ static void doc_set_device_id(struct docg3 *docg3, int id) * leveling counters are stored. To access this last area of 4 bytes, a special * mode must be input to the flash ASIC. * - * Returns 0 if no error occured, -EIO else. + * Returns 0 if no error occurred, -EIO else. */ static int doc_set_extra_page_mode(struct docg3 *docg3) { @@ -643,7 +638,8 @@ static int doc_ecc_bch_fix_data(struct docg3 *docg3, void *buf, u8 *hwecc) for (i = 0; i < DOC_ECC_BCH_SIZE; i++) ecc[i] = bitrev8(hwecc[i]); - numerrs = decode_bch(docg3_bch, NULL, DOC_ECC_BCH_COVERED_BYTES, + numerrs = decode_bch(docg3->cascade->bch, NULL, + DOC_ECC_BCH_COVERED_BYTES, NULL, ecc, NULL, errorpos); BUG_ON(numerrs == -EINVAL); if (numerrs < 0) @@ -685,7 +681,7 @@ out: * - one read of 512 bytes at offset 0 * - one read of 512 bytes at offset 512 + 16 * - * Returns 0 if successful, -EIO if a read error occured. + * Returns 0 if successful, -EIO if a read error occurred. */ static int doc_read_page_prepare(struct docg3 *docg3, int block0, int block1, int page, int offset) @@ -734,14 +730,26 @@ err: * doc_read_page_getbytes - Reads bytes from a prepared page * @docg3: the device * @len: the number of bytes to be read (must be a multiple of 4) - * @buf: the buffer to be filled in + * @buf: the buffer to be filled in (or NULL is forget bytes) * @first: 1 if first time read, DOC_READADDRESS should be set + * @last_odd: 1 if last read ended up on an odd byte + * + * Reads bytes from a prepared page. There is a trickery here : if the last read + * ended up on an odd offset in the 1024 bytes double page, ie. between the 2 + * planes, the first byte must be read apart. If a word (16bit) read was used, + * the read would return the byte of plane 2 as low *and* high endian, which + * will mess the read. * */ static int doc_read_page_getbytes(struct docg3 *docg3, int len, u_char *buf, - int first) + int first, int last_odd) { - doc_read_data_area(docg3, buf, len, first); + if (last_odd && len > 0) { + doc_read_data_area(docg3, buf, 1, first); + doc_read_data_area(docg3, buf ? buf + 1 : buf, len - 1, 0); + } else { + doc_read_data_area(docg3, buf, len, first); + } doc_delay(docg3, 2); return len; } @@ -843,17 +851,18 @@ static void calc_block_sector(loff_t from, int *block0, int *block1, int *page, * * Reads flash memory OOB area of pages. * - * Returns 0 if read successfull, of -EIO, -EINVAL if an error occured + * Returns 0 if read successful, of -EIO, -EINVAL if an error occurred */ static int doc_read_oob(struct mtd_info *mtd, loff_t from, struct mtd_oob_ops *ops) { struct docg3 *docg3 = mtd->priv; - int block0, block1, page, ret, ofs = 0; + int block0, block1, page, ret, skip, ofs = 0; u8 *oobbuf = ops->oobbuf; u8 *buf = ops->datbuf; size_t len, ooblen, nbdata, nboob; u8 hwecc[DOC_ECC_BCH_SIZE], eccconf1; + int max_bitflips = 0; if (buf) len = ops->len; @@ -869,58 +878,54 @@ static int doc_read_oob(struct mtd_info *mtd, loff_t from, doc_dbg("doc_read_oob(from=%lld, mode=%d, data=(%p:%zu), oob=(%p:%zu))\n", from, ops->mode, buf, len, oobbuf, ooblen); - if ((len % DOC_LAYOUT_PAGE_SIZE) || (ooblen % DOC_LAYOUT_OOB_SIZE) || - (from % DOC_LAYOUT_PAGE_SIZE)) + if (ooblen % DOC_LAYOUT_OOB_SIZE) return -EINVAL; - ret = -EINVAL; - calc_block_sector(from + len, &block0, &block1, &page, &ofs, - docg3->reliable); - if (block1 > docg3->max_block) - goto err; + if (from + len > mtd->size) + return -EINVAL; ops->oobretlen = 0; ops->retlen = 0; ret = 0; - while (!ret && (len > 0 || ooblen > 0)) { - calc_block_sector(from, &block0, &block1, &page, &ofs, + skip = from % DOC_LAYOUT_PAGE_SIZE; + mutex_lock(&docg3->cascade->lock); + while (ret >= 0 && (len > 0 || ooblen > 0)) { + calc_block_sector(from - skip, &block0, &block1, &page, &ofs, docg3->reliable); - nbdata = min_t(size_t, len, (size_t)DOC_LAYOUT_PAGE_SIZE); + nbdata = min_t(size_t, len, DOC_LAYOUT_PAGE_SIZE - skip); nboob = min_t(size_t, ooblen, (size_t)DOC_LAYOUT_OOB_SIZE); ret = doc_read_page_prepare(docg3, block0, block1, page, ofs); if (ret < 0) - goto err; + goto out; ret = doc_read_page_ecc_init(docg3, DOC_ECC_BCH_TOTAL_BYTES); if (ret < 0) goto err_in_read; - ret = doc_read_page_getbytes(docg3, nbdata, buf, 1); + ret = doc_read_page_getbytes(docg3, skip, NULL, 1, 0); + if (ret < skip) + goto err_in_read; + ret = doc_read_page_getbytes(docg3, nbdata, buf, 0, skip % 2); if (ret < nbdata) goto err_in_read; - doc_read_page_getbytes(docg3, DOC_LAYOUT_PAGE_SIZE - nbdata, - NULL, 0); - ret = doc_read_page_getbytes(docg3, nboob, oobbuf, 0); + doc_read_page_getbytes(docg3, + DOC_LAYOUT_PAGE_SIZE - nbdata - skip, + NULL, 0, (skip + nbdata) % 2); + ret = doc_read_page_getbytes(docg3, nboob, oobbuf, 0, 0); if (ret < nboob) goto err_in_read; doc_read_page_getbytes(docg3, DOC_LAYOUT_OOB_SIZE - nboob, - NULL, 0); + NULL, 0, nboob % 2); doc_get_bch_hw_ecc(docg3, hwecc); eccconf1 = doc_register_readb(docg3, DOC_ECCCONF1); if (nboob >= DOC_LAYOUT_OOB_SIZE) { - doc_dbg("OOB - INFO: %02x:%02x:%02x:%02x:%02x:%02x:%02x\n", - oobbuf[0], oobbuf[1], oobbuf[2], oobbuf[3], - oobbuf[4], oobbuf[5], oobbuf[6]); + doc_dbg("OOB - INFO: %*phC\n", 7, oobbuf); doc_dbg("OOB - HAMMING: %02x\n", oobbuf[7]); - doc_dbg("OOB - BCH_ECC: %02x:%02x:%02x:%02x:%02x:%02x:%02x\n", - oobbuf[8], oobbuf[9], oobbuf[10], oobbuf[11], - oobbuf[12], oobbuf[13], oobbuf[14]); + doc_dbg("OOB - BCH_ECC: %*phC\n", 7, oobbuf + 8); doc_dbg("OOB - UNUSED: %02x\n", oobbuf[15]); } doc_dbg("ECC checks: ECCConf1=%x\n", eccconf1); - doc_dbg("ECC HW_ECC: %02x:%02x:%02x:%02x:%02x:%02x:%02x\n", - hwecc[0], hwecc[1], hwecc[2], hwecc[3], hwecc[4], - hwecc[5], hwecc[6]); + doc_dbg("ECC HW_ECC: %*phC\n", 7, hwecc); ret = -EIO; if (is_prot_seq_error(docg3)) @@ -938,7 +943,8 @@ static int doc_read_oob(struct mtd_info *mtd, loff_t from, } if (ret > 0) { mtd->ecc_stats.corrected += ret; - ret = -EUCLEAN; + max_bitflips = max(max_bitflips, ret); + ret = max_bitflips; } } @@ -950,13 +956,15 @@ static int doc_read_oob(struct mtd_info *mtd, loff_t from, len -= nbdata; ooblen -= nboob; from += DOC_LAYOUT_PAGE_SIZE; + skip = 0; } +out: + mutex_unlock(&docg3->cascade->lock); return ret; err_in_read: doc_read_page_finish(docg3); -err: - return ret; + goto out; } /** @@ -971,7 +979,7 @@ err: * Reads flash memory pages. This function does not read the OOB chunk, but only * the page data. * - * Returns 0 if read successfull, of -EIO, -EINVAL if an error occured + * Returns 0 if read successful, of -EIO, -EINVAL if an error occurred */ static int doc_read(struct mtd_info *mtd, loff_t from, size_t len, size_t *retlen, u_char *buf) @@ -1004,7 +1012,7 @@ static int doc_reload_bbt(struct docg3 *docg3) DOC_LAYOUT_PAGE_SIZE); if (!ret) doc_read_page_getbytes(docg3, DOC_LAYOUT_PAGE_SIZE, - buf, 1); + buf, 1, 0); buf += DOC_LAYOUT_PAGE_SIZE; } doc_read_page_finish(docg3); @@ -1064,10 +1072,10 @@ static int doc_get_erase_count(struct docg3 *docg3, loff_t from) ret = doc_reset_seq(docg3); if (!ret) ret = doc_read_page_prepare(docg3, block0, block1, page, - ofs + DOC_LAYOUT_WEAR_OFFSET); + ofs + DOC_LAYOUT_WEAR_OFFSET, 0); if (!ret) ret = doc_read_page_getbytes(docg3, DOC_LAYOUT_WEAR_SIZE, - buf, 1); + buf, 1, 0); doc_read_page_finish(docg3); if (ret || (buf[0] != DOC_ERASE_MARK) || (buf[2] != DOC_ERASE_MARK)) @@ -1109,15 +1117,15 @@ static int doc_get_op_status(struct docg3 *docg3) * Wait for the chip to be ready again after erase or write operation, and check * erase/write status. * - * Returns 0 if erase successfull, -EIO if erase/write issue, -ETIMEOUT if + * Returns 0 if erase successful, -EIO if erase/write issue, -ETIMEOUT if * timeout */ static int doc_write_erase_wait_status(struct docg3 *docg3) { - int status, ret = 0; + int i, status, ret = 0; - if (!doc_is_ready(docg3)) - usleep_range(3000, 3000); + for (i = 0; !doc_is_ready(docg3) && i < 5; i++) + msleep(20); if (!doc_is_ready(docg3)) { doc_dbg("Timeout reached and the chip is still not ready\n"); ret = -EAGAIN; @@ -1186,7 +1194,7 @@ static int doc_erase_block(struct docg3 *docg3, int block0, int block1) * Erase a bunch of contiguous blocks, by pairs, as a "mtd" page of 1024 is * split into 2 pages of 512 bytes on 2 contiguous blocks. * - * Returns 0 if erase successful, -EINVAL if adressing error, -EIO if erase + * Returns 0 if erase successful, -EINVAL if addressing error, -EIO if erase * issue */ static int doc_erase(struct mtd_info *mtd, struct erase_info *info) @@ -1196,18 +1204,19 @@ static int doc_erase(struct mtd_info *mtd, struct erase_info *info) int block0, block1, page, ret, ofs = 0; doc_dbg("doc_erase(from=%lld, len=%lld\n", info->addr, info->len); - doc_set_device_id(docg3, docg3->device_id); info->state = MTD_ERASE_PENDING; calc_block_sector(info->addr + info->len, &block0, &block1, &page, &ofs, docg3->reliable); ret = -EINVAL; - if (block1 > docg3->max_block || page || ofs) + if (info->addr + info->len > mtd->size || page || ofs) goto reset_err; ret = 0; calc_block_sector(info->addr, &block0, &block1, &page, &ofs, docg3->reliable); + mutex_lock(&docg3->cascade->lock); + doc_set_device_id(docg3, docg3->device_id); doc_set_reliable_mode(docg3); for (len = info->len; !ret && len > 0; len -= mtd->erasesize) { info->state = MTD_ERASING; @@ -1215,6 +1224,7 @@ static int doc_erase(struct mtd_info *mtd, struct erase_info *info) block0 += 2; block1 += 2; } + mutex_unlock(&docg3->cascade->lock); if (ret) goto reset_err; @@ -1395,13 +1405,13 @@ static int doc_backup_oob(struct docg3 *docg3, loff_t to, * Or provide data without OOB, and then a all zeroed OOB will be used (ECC will * still be filled in if asked for). * - * Returns 0 is successfull, EINVAL if length is not 14 bytes + * Returns 0 is successful, EINVAL if length is not 14 bytes */ static int doc_write_oob(struct mtd_info *mtd, loff_t ofs, struct mtd_oob_ops *ops) { struct docg3 *docg3 = mtd->priv; - int block0, block1, page, ret, pofs = 0, autoecc, oobdelta; + int ret, autoecc, oobdelta; u8 *oobbuf = ops->oobbuf; u8 *buf = ops->datbuf; size_t len, ooblen; @@ -1430,7 +1440,7 @@ static int doc_write_oob(struct mtd_info *mtd, loff_t ofs, oobdelta = mtd->ecclayout->oobavail; break; default: - oobdelta = 0; + return -EINVAL; } if ((len % DOC_LAYOUT_PAGE_SIZE) || (ooblen % oobdelta) || (ofs % DOC_LAYOUT_PAGE_SIZE)) @@ -1438,12 +1448,8 @@ static int doc_write_oob(struct mtd_info *mtd, loff_t ofs, if (len && ooblen && (len / DOC_LAYOUT_PAGE_SIZE) != (ooblen / oobdelta)) return -EINVAL; - - ret = -EINVAL; - calc_block_sector(ofs + len, &block0, &block1, &page, &pofs, - docg3->reliable); - if (block1 > docg3->max_block) - goto err; + if (ofs + len > mtd->size) + return -EINVAL; ops->oobretlen = 0; ops->retlen = 0; @@ -1457,6 +1463,7 @@ static int doc_write_oob(struct mtd_info *mtd, loff_t ofs, if (autoecc < 0) return autoecc; + mutex_lock(&docg3->cascade->lock); while (!ret && len > 0) { memset(oob, 0, sizeof(oob)); if (ofs == docg3->oob_write_ofs) @@ -1477,8 +1484,9 @@ static int doc_write_oob(struct mtd_info *mtd, loff_t ofs, } ops->retlen += DOC_LAYOUT_PAGE_SIZE; } -err: + doc_set_device_id(docg3, 0); + mutex_unlock(&docg3->cascade->lock); return ret; } @@ -1535,9 +1543,11 @@ static ssize_t dps0_is_key_locked(struct device *dev, struct docg3 *docg3 = sysfs_dev2docg3(dev, attr); int dps0; + mutex_lock(&docg3->cascade->lock); doc_set_device_id(docg3, docg3->device_id); dps0 = doc_register_readb(docg3, DOC_DPS0_STATUS); doc_set_device_id(docg3, 0); + mutex_unlock(&docg3->cascade->lock); return sprintf(buf, "%d\n", !(dps0 & DOC_DPS_KEY_OK)); } @@ -1548,9 +1558,11 @@ static ssize_t dps1_is_key_locked(struct device *dev, struct docg3 *docg3 = sysfs_dev2docg3(dev, attr); int dps1; + mutex_lock(&docg3->cascade->lock); doc_set_device_id(docg3, docg3->device_id); dps1 = doc_register_readb(docg3, DOC_DPS1_STATUS); doc_set_device_id(docg3, 0); + mutex_unlock(&docg3->cascade->lock); return sprintf(buf, "%d\n", !(dps1 & DOC_DPS_KEY_OK)); } @@ -1565,10 +1577,12 @@ static ssize_t dps0_insert_key(struct device *dev, if (count != DOC_LAYOUT_DPS_KEY_LENGTH) return -EINVAL; + mutex_lock(&docg3->cascade->lock); doc_set_device_id(docg3, docg3->device_id); for (i = 0; i < DOC_LAYOUT_DPS_KEY_LENGTH; i++) doc_writeb(docg3, buf[i], DOC_DPS0_KEY); doc_set_device_id(docg3, 0); + mutex_unlock(&docg3->cascade->lock); return count; } @@ -1582,18 +1596,20 @@ static ssize_t dps1_insert_key(struct device *dev, if (count != DOC_LAYOUT_DPS_KEY_LENGTH) return -EINVAL; + mutex_lock(&docg3->cascade->lock); doc_set_device_id(docg3, docg3->device_id); for (i = 0; i < DOC_LAYOUT_DPS_KEY_LENGTH; i++) doc_writeb(docg3, buf[i], DOC_DPS1_KEY); doc_set_device_id(docg3, 0); + mutex_unlock(&docg3->cascade->lock); return count; } #define FLOOR_SYSFS(id) { \ __ATTR(f##id##_dps0_is_keylocked, S_IRUGO, dps0_is_key_locked, NULL), \ __ATTR(f##id##_dps1_is_keylocked, S_IRUGO, dps1_is_key_locked, NULL), \ - __ATTR(f##id##_dps0_protection_key, S_IWUGO, NULL, dps0_insert_key), \ - __ATTR(f##id##_dps1_protection_key, S_IWUGO, NULL, dps1_insert_key), \ + __ATTR(f##id##_dps0_protection_key, S_IWUSR|S_IWGRP, NULL, dps0_insert_key), \ + __ATTR(f##id##_dps1_protection_key, S_IWUSR|S_IWGRP, NULL, dps1_insert_key), \ } static struct device_attribute doc_sys_attrs[DOC_MAX_NBFLOORS][4] = { @@ -1601,13 +1617,13 @@ static struct device_attribute doc_sys_attrs[DOC_MAX_NBFLOORS][4] = { }; static int doc_register_sysfs(struct platform_device *pdev, - struct mtd_info **floors) + struct docg3_cascade *cascade) { int ret = 0, floor, i = 0; struct device *dev = &pdev->dev; - for (floor = 0; !ret && floor < DOC_MAX_NBFLOORS && floors[floor]; - floor++) + for (floor = 0; !ret && floor < DOC_MAX_NBFLOORS && + cascade->floors[floor]; floor++) for (i = 0; !ret && i < 4; i++) ret = device_create_file(dev, &doc_sys_attrs[floor][i]); if (!ret) @@ -1621,12 +1637,12 @@ static int doc_register_sysfs(struct platform_device *pdev, } static void doc_unregister_sysfs(struct platform_device *pdev, - struct mtd_info **floors) + struct docg3_cascade *cascade) { struct device *dev = &pdev->dev; int floor, i; - for (floor = 0; floor < DOC_MAX_NBFLOORS && floors[floor]; + for (floor = 0; floor < DOC_MAX_NBFLOORS && cascade->floors[floor]; floor++) for (i = 0; i < 4; i++) device_remove_file(dev, &doc_sys_attrs[floor][i]); @@ -1640,7 +1656,11 @@ static int dbg_flashctrl_show(struct seq_file *s, void *p) struct docg3 *docg3 = (struct docg3 *)s->private; int pos = 0; - u8 fctrl = doc_register_readb(docg3, DOC_FLASHCONTROL); + u8 fctrl; + + mutex_lock(&docg3->cascade->lock); + fctrl = doc_register_readb(docg3, DOC_FLASHCONTROL); + mutex_unlock(&docg3->cascade->lock); pos += seq_printf(s, "FlashControl : 0x%02x (%s,CE# %s,%s,%s,flash %s)\n", @@ -1658,9 +1678,12 @@ static int dbg_asicmode_show(struct seq_file *s, void *p) { struct docg3 *docg3 = (struct docg3 *)s->private; - int pos = 0; - int pctrl = doc_register_readb(docg3, DOC_ASICMODE); - int mode = pctrl & 0x03; + int pos = 0, pctrl, mode; + + mutex_lock(&docg3->cascade->lock); + pctrl = doc_register_readb(docg3, DOC_ASICMODE); + mode = pctrl & 0x03; + mutex_unlock(&docg3->cascade->lock); pos += seq_printf(s, "%04x : RAM_WE=%d,RSTIN_RESET=%d,BDETCT_RESET=%d,WRITE_ENABLE=%d,POWERDOWN=%d,MODE=%d%d (", @@ -1692,7 +1715,11 @@ static int dbg_device_id_show(struct seq_file *s, void *p) { struct docg3 *docg3 = (struct docg3 *)s->private; int pos = 0; - int id = doc_register_readb(docg3, DOC_DEVICESELECT); + int id; + + mutex_lock(&docg3->cascade->lock); + id = doc_register_readb(docg3, DOC_DEVICESELECT); + mutex_unlock(&docg3->cascade->lock); pos += seq_printf(s, "DeviceId = %d\n", id); return pos; @@ -1705,6 +1732,7 @@ static int dbg_protection_show(struct seq_file *s, void *p) int pos = 0; int protect, dps0, dps0_low, dps0_high, dps1, dps1_low, dps1_high; + mutex_lock(&docg3->cascade->lock); protect = doc_register_readb(docg3, DOC_PROTECTION); dps0 = doc_register_readb(docg3, DOC_DPS0_STATUS); dps0_low = doc_register_readw(docg3, DOC_DPS0_ADDRLOW); @@ -1712,6 +1740,7 @@ static int dbg_protection_show(struct seq_file *s, void *p) dps1 = doc_register_readb(docg3, DOC_DPS1_STATUS); dps1_low = doc_register_readw(docg3, DOC_DPS1_ADDRLOW); dps1_high = doc_register_readw(docg3, DOC_DPS1_ADDRHIGH); + mutex_unlock(&docg3->cascade->lock); pos += seq_printf(s, "Protection = 0x%02x (", protect); @@ -1804,7 +1833,7 @@ static void __init doc_set_driver_info(int chip_id, struct mtd_info *mtd) switch (chip_id) { case DOC_CHIPID_G3: - mtd->name = kasprintf(GFP_KERNEL, "DiskOnChip G3 floor %d", + mtd->name = kasprintf(GFP_KERNEL, "docg3.%d", docg3->device_id); docg3->max_block = 2047; break; @@ -1817,16 +1846,17 @@ static void __init doc_set_driver_info(int chip_id, struct mtd_info *mtd) mtd->erasesize = DOC_LAYOUT_BLOCK_SIZE * DOC_LAYOUT_NBPLANES; if (docg3->reliable == 2) mtd->erasesize /= 2; - mtd->writesize = DOC_LAYOUT_PAGE_SIZE; + mtd->writebufsize = mtd->writesize = DOC_LAYOUT_PAGE_SIZE; mtd->oobsize = DOC_LAYOUT_OOB_SIZE; mtd->owner = THIS_MODULE; - mtd->erase = doc_erase; - mtd->read = doc_read; - mtd->write = doc_write; - mtd->read_oob = doc_read_oob; - mtd->write_oob = doc_write_oob; - mtd->block_isbad = doc_block_isbad; + mtd->_erase = doc_erase; + mtd->_read = doc_read; + mtd->_write = doc_write; + mtd->_read_oob = doc_read_oob; + mtd->_write_oob = doc_write_oob; + mtd->_block_isbad = doc_block_isbad; mtd->ecclayout = &docg3_oobinfo; + mtd->ecc_strength = DOC_ECC_BCH_T; } /** @@ -1834,6 +1864,7 @@ static void __init doc_set_driver_info(int chip_id, struct mtd_info *mtd) * @base: the io space where the device is probed * @floor: the floor of the probed device * @dev: the device + * @cascade: the cascade of chips this devices will belong to * * Checks whether a device at the specified IO range, and floor is available. * @@ -1841,8 +1872,8 @@ static void __init doc_set_driver_info(int chip_id, struct mtd_info *mtd) * if a memory allocation failed. If floor 0 is checked, a reset of the ASIC is * launched. */ -static struct mtd_info *doc_probe_device(void __iomem *base, int floor, - struct device *dev) +static struct mtd_info * __init +doc_probe_device(struct docg3_cascade *cascade, int floor, struct device *dev) { int ret, bbt_nbpages; u16 chip_id, chip_id_inv; @@ -1865,7 +1896,7 @@ static struct mtd_info *doc_probe_device(void __iomem *base, int floor, docg3->dev = dev; docg3->device_id = floor; - docg3->base = base; + docg3->cascade = cascade; doc_set_device_id(docg3, docg3->device_id); if (!floor) doc_set_asic_mode(docg3, DOC_ASICMODE_RESET); @@ -1882,7 +1913,7 @@ static struct mtd_info *doc_probe_device(void __iomem *base, int floor, switch (chip_id) { case DOC_CHIPID_G3: doc_info("Found a G3 DiskOnChip at addr %p, floor %d\n", - base, floor); + docg3->cascade->base, floor); break; default: doc_err("Chip id %04x is not a DiskOnChip G3 chip\n", chip_id); @@ -1922,15 +1953,17 @@ static void doc_release_device(struct mtd_info *mtd) * docg3_resume - Awakens docg3 floor * @pdev: platfrom device * - * Returns 0 (always successfull) + * Returns 0 (always successful) */ static int docg3_resume(struct platform_device *pdev) { int i; + struct docg3_cascade *cascade; struct mtd_info **docg3_floors, *mtd; struct docg3 *docg3; - docg3_floors = platform_get_drvdata(pdev); + cascade = platform_get_drvdata(pdev); + docg3_floors = cascade->floors; mtd = docg3_floors[0]; docg3 = mtd->priv; @@ -1952,11 +1985,13 @@ static int docg3_resume(struct platform_device *pdev) static int docg3_suspend(struct platform_device *pdev, pm_message_t state) { int floor, i; + struct docg3_cascade *cascade; struct mtd_info **docg3_floors, *mtd; struct docg3 *docg3; u8 ctrl, pwr_down; - docg3_floors = platform_get_drvdata(pdev); + cascade = platform_get_drvdata(pdev); + docg3_floors = cascade->floors; for (floor = 0; floor < DOC_MAX_NBFLOORS; floor++) { mtd = docg3_floors[floor]; if (!mtd) @@ -2006,28 +2041,30 @@ static int __init docg3_probe(struct platform_device *pdev) struct resource *ress; void __iomem *base; int ret, floor, found = 0; - struct mtd_info **docg3_floors; + struct docg3_cascade *cascade; ret = -ENXIO; ress = platform_get_resource(pdev, IORESOURCE_MEM, 0); if (!ress) { dev_err(dev, "No I/O memory resource defined\n"); - goto noress; + return ret; } - base = ioremap(ress->start, DOC_IOSPACE_SIZE); + base = devm_ioremap(dev, ress->start, DOC_IOSPACE_SIZE); ret = -ENOMEM; - docg3_floors = kzalloc(sizeof(*docg3_floors) * DOC_MAX_NBFLOORS, + cascade = devm_kzalloc(dev, sizeof(*cascade) * DOC_MAX_NBFLOORS, GFP_KERNEL); - if (!docg3_floors) - goto nomem1; - docg3_bch = init_bch(DOC_ECC_BCH_M, DOC_ECC_BCH_T, + if (!cascade) + return ret; + cascade->base = base; + mutex_init(&cascade->lock); + cascade->bch = init_bch(DOC_ECC_BCH_M, DOC_ECC_BCH_T, DOC_ECC_BCH_PRIMPOLY); - if (!docg3_bch) - goto nomem2; + if (!cascade->bch) + return ret; for (floor = 0; floor < DOC_MAX_NBFLOORS; floor++) { - mtd = doc_probe_device(base, floor, dev); + mtd = doc_probe_device(cascade, floor, dev); if (IS_ERR(mtd)) { ret = PTR_ERR(mtd); goto err_probe; @@ -2038,7 +2075,7 @@ static int __init docg3_probe(struct platform_device *pdev) else continue; } - docg3_floors[floor] = mtd; + cascade->floors[floor] = mtd; ret = mtd_device_parse_register(mtd, part_probes, NULL, NULL, 0); if (ret) @@ -2046,29 +2083,24 @@ static int __init docg3_probe(struct platform_device *pdev) found++; } - ret = doc_register_sysfs(pdev, docg3_floors); + ret = doc_register_sysfs(pdev, cascade); if (ret) goto err_probe; if (!found) goto notfound; - platform_set_drvdata(pdev, docg3_floors); - doc_dbg_register(docg3_floors[0]->priv); + platform_set_drvdata(pdev, cascade); + doc_dbg_register(cascade->floors[0]->priv); return 0; notfound: ret = -ENODEV; dev_info(dev, "No supported DiskOnChip found\n"); err_probe: - free_bch(docg3_bch); + free_bch(cascade->bch); for (floor = 0; floor < DOC_MAX_NBFLOORS; floor++) - if (docg3_floors[floor]) - doc_release_device(docg3_floors[floor]); -nomem2: - kfree(docg3_floors); -nomem1: - iounmap(base); -noress: + if (cascade->floors[floor]) + doc_release_device(cascade->floors[floor]); return ret; } @@ -2080,20 +2112,17 @@ noress: */ static int __exit docg3_release(struct platform_device *pdev) { - struct mtd_info **docg3_floors = platform_get_drvdata(pdev); - struct docg3 *docg3 = docg3_floors[0]->priv; - void __iomem *base = docg3->base; + struct docg3_cascade *cascade = platform_get_drvdata(pdev); + struct docg3 *docg3 = cascade->floors[0]->priv; int floor; - doc_unregister_sysfs(pdev, docg3_floors); + doc_unregister_sysfs(pdev, cascade); doc_dbg_unregister(docg3); for (floor = 0; floor < DOC_MAX_NBFLOORS; floor++) - if (docg3_floors[floor]) - doc_release_device(docg3_floors[floor]); + if (cascade->floors[floor]) + doc_release_device(cascade->floors[floor]); - kfree(docg3_floors); - free_bch(docg3_bch); - iounmap(base); + free_bch(docg3->cascade->bch); return 0; } @@ -2107,18 +2136,7 @@ static struct platform_driver g3_driver = { .remove = __exit_p(docg3_release), }; -static int __init docg3_init(void) -{ - return platform_driver_probe(&g3_driver, docg3_probe); -} -module_init(docg3_init); - - -static void __exit docg3_exit(void) -{ - platform_driver_unregister(&g3_driver); -} -module_exit(docg3_exit); +module_platform_driver_probe(g3_driver, docg3_probe); MODULE_LICENSE("GPL"); MODULE_AUTHOR("Robert Jarzmik <robert.jarzmik@free.fr>"); diff --git a/drivers/mtd/devices/docg3.h b/drivers/mtd/devices/docg3.h index db0da436b49..19fb93f96a3 100644 --- a/drivers/mtd/devices/docg3.h +++ b/drivers/mtd/devices/docg3.h @@ -22,6 +22,8 @@ #ifndef _MTD_DOCG3_H #define _MTD_DOCG3_H +#include <linux/mtd/mtd.h> + /* * Flash memory areas : * - 0x0000 .. 0x07ff : IPL @@ -267,9 +269,23 @@ #define DOC_LAYOUT_DPS_KEY_LENGTH 8 /** + * struct docg3_cascade - Cascade of 1 to 4 docg3 chips + * @floors: floors (ie. one physical docg3 chip is one floor) + * @base: IO space to access all chips in the cascade + * @bch: the BCH correcting control structure + * @lock: lock to protect docg3 IO space from concurrent accesses + */ +struct docg3_cascade { + struct mtd_info *floors[DOC_MAX_NBFLOORS]; + void __iomem *base; + struct bch_control *bch; + struct mutex lock; +}; + +/** * struct docg3 - DiskOnChip driver private data * @dev: the device currently under control - * @base: mapped IO space + * @cascade: the cascade this device belongs to * @device_id: number of the cascaded DoCG3 device (0, 1, 2 or 3) * @if_cfg: if true, reads are on 16bits, else reads are on 8bits @@ -287,7 +303,7 @@ */ struct docg3 { struct device *dev; - void __iomem *base; + struct docg3_cascade *cascade; unsigned int device_id:4; unsigned int if_cfg:1; unsigned int reliable:2; diff --git a/drivers/mtd/devices/docprobe.c b/drivers/mtd/devices/docprobe.c deleted file mode 100644 index 706b847b46b..00000000000 --- a/drivers/mtd/devices/docprobe.c +++ /dev/null @@ -1,327 +0,0 @@ - -/* Linux driver for Disk-On-Chip devices */ -/* Probe routines common to all DoC devices */ -/* (C) 1999 Machine Vision Holdings, Inc. */ -/* (C) 1999-2003 David Woodhouse <dwmw2@infradead.org> */ - - -/* DOC_PASSIVE_PROBE: - In order to ensure that the BIOS checksum is correct at boot time, and - hence that the onboard BIOS extension gets executed, the DiskOnChip - goes into reset mode when it is read sequentially: all registers - return 0xff until the chip is woken up again by writing to the - DOCControl register. - - Unfortunately, this means that the probe for the DiskOnChip is unsafe, - because one of the first things it does is write to where it thinks - the DOCControl register should be - which may well be shared memory - for another device. I've had machines which lock up when this is - attempted. Hence the possibility to do a passive probe, which will fail - to detect a chip in reset mode, but is at least guaranteed not to lock - the machine. - - If you have this problem, uncomment the following line: -#define DOC_PASSIVE_PROBE -*/ - - -/* DOC_SINGLE_DRIVER: - Millennium driver has been merged into DOC2000 driver. - - The old Millennium-only driver has been retained just in case there - are problems with the new code. If the combined driver doesn't work - for you, you can try the old one by undefining DOC_SINGLE_DRIVER - below and also enabling it in your configuration. If this fixes the - problems, please send a report to the MTD mailing list at - <linux-mtd@lists.infradead.org>. -*/ -#define DOC_SINGLE_DRIVER - -#include <linux/kernel.h> -#include <linux/module.h> -#include <asm/errno.h> -#include <asm/io.h> -#include <linux/delay.h> -#include <linux/slab.h> -#include <linux/init.h> -#include <linux/types.h> - -#include <linux/mtd/mtd.h> -#include <linux/mtd/nand.h> -#include <linux/mtd/doc2000.h> - - -static unsigned long doc_config_location = CONFIG_MTD_DOCPROBE_ADDRESS; -module_param(doc_config_location, ulong, 0); -MODULE_PARM_DESC(doc_config_location, "Physical memory address at which to probe for DiskOnChip"); - -static unsigned long __initdata doc_locations[] = { -#if defined (__alpha__) || defined(__i386__) || defined(__x86_64__) -#ifdef CONFIG_MTD_DOCPROBE_HIGH - 0xfffc8000, 0xfffca000, 0xfffcc000, 0xfffce000, - 0xfffd0000, 0xfffd2000, 0xfffd4000, 0xfffd6000, - 0xfffd8000, 0xfffda000, 0xfffdc000, 0xfffde000, - 0xfffe0000, 0xfffe2000, 0xfffe4000, 0xfffe6000, - 0xfffe8000, 0xfffea000, 0xfffec000, 0xfffee000, -#else /* CONFIG_MTD_DOCPROBE_HIGH */ - 0xc8000, 0xca000, 0xcc000, 0xce000, - 0xd0000, 0xd2000, 0xd4000, 0xd6000, - 0xd8000, 0xda000, 0xdc000, 0xde000, - 0xe0000, 0xe2000, 0xe4000, 0xe6000, - 0xe8000, 0xea000, 0xec000, 0xee000, -#endif /* CONFIG_MTD_DOCPROBE_HIGH */ -#else -#warning Unknown architecture for DiskOnChip. No default probe locations defined -#endif - 0xffffffff }; - -/* doccheck: Probe a given memory window to see if there's a DiskOnChip present */ - -static inline int __init doccheck(void __iomem *potential, unsigned long physadr) -{ - void __iomem *window=potential; - unsigned char tmp, tmpb, tmpc, ChipID; -#ifndef DOC_PASSIVE_PROBE - unsigned char tmp2; -#endif - - /* Routine copied from the Linux DOC driver */ - -#ifdef CONFIG_MTD_DOCPROBE_55AA - /* Check for 0x55 0xAA signature at beginning of window, - this is no longer true once we remove the IPL (for Millennium */ - if (ReadDOC(window, Sig1) != 0x55 || ReadDOC(window, Sig2) != 0xaa) - return 0; -#endif /* CONFIG_MTD_DOCPROBE_55AA */ - -#ifndef DOC_PASSIVE_PROBE - /* It's not possible to cleanly detect the DiskOnChip - the - * bootup procedure will put the device into reset mode, and - * it's not possible to talk to it without actually writing - * to the DOCControl register. So we store the current contents - * of the DOCControl register's location, in case we later decide - * that it's not a DiskOnChip, and want to put it back how we - * found it. - */ - tmp2 = ReadDOC(window, DOCControl); - - /* Reset the DiskOnChip ASIC */ - WriteDOC(DOC_MODE_CLR_ERR | DOC_MODE_MDWREN | DOC_MODE_RESET, - window, DOCControl); - WriteDOC(DOC_MODE_CLR_ERR | DOC_MODE_MDWREN | DOC_MODE_RESET, - window, DOCControl); - - /* Enable the DiskOnChip ASIC */ - WriteDOC(DOC_MODE_CLR_ERR | DOC_MODE_MDWREN | DOC_MODE_NORMAL, - window, DOCControl); - WriteDOC(DOC_MODE_CLR_ERR | DOC_MODE_MDWREN | DOC_MODE_NORMAL, - window, DOCControl); -#endif /* !DOC_PASSIVE_PROBE */ - - /* We need to read the ChipID register four times. For some - newer DiskOnChip 2000 units, the first three reads will - return the DiskOnChip Millennium ident. Don't ask. */ - ChipID = ReadDOC(window, ChipID); - - switch (ChipID) { - case DOC_ChipID_Doc2k: - /* Check the TOGGLE bit in the ECC register */ - tmp = ReadDOC(window, 2k_ECCStatus) & DOC_TOGGLE_BIT; - tmpb = ReadDOC(window, 2k_ECCStatus) & DOC_TOGGLE_BIT; - tmpc = ReadDOC(window, 2k_ECCStatus) & DOC_TOGGLE_BIT; - if (tmp != tmpb && tmp == tmpc) - return ChipID; - break; - - case DOC_ChipID_DocMil: - /* Check for the new 2000 with Millennium ASIC */ - ReadDOC(window, ChipID); - ReadDOC(window, ChipID); - if (ReadDOC(window, ChipID) != DOC_ChipID_DocMil) - ChipID = DOC_ChipID_Doc2kTSOP; - - /* Check the TOGGLE bit in the ECC register */ - tmp = ReadDOC(window, ECCConf) & DOC_TOGGLE_BIT; - tmpb = ReadDOC(window, ECCConf) & DOC_TOGGLE_BIT; - tmpc = ReadDOC(window, ECCConf) & DOC_TOGGLE_BIT; - if (tmp != tmpb && tmp == tmpc) - return ChipID; - break; - - case DOC_ChipID_DocMilPlus16: - case DOC_ChipID_DocMilPlus32: - case 0: - /* Possible Millennium+, need to do more checks */ -#ifndef DOC_PASSIVE_PROBE - /* Possibly release from power down mode */ - for (tmp = 0; (tmp < 4); tmp++) - ReadDOC(window, Mplus_Power); - - /* Reset the DiskOnChip ASIC */ - tmp = DOC_MODE_RESET | DOC_MODE_MDWREN | DOC_MODE_RST_LAT | - DOC_MODE_BDECT; - WriteDOC(tmp, window, Mplus_DOCControl); - WriteDOC(~tmp, window, Mplus_CtrlConfirm); - - mdelay(1); - /* Enable the DiskOnChip ASIC */ - tmp = DOC_MODE_NORMAL | DOC_MODE_MDWREN | DOC_MODE_RST_LAT | - DOC_MODE_BDECT; - WriteDOC(tmp, window, Mplus_DOCControl); - WriteDOC(~tmp, window, Mplus_CtrlConfirm); - mdelay(1); -#endif /* !DOC_PASSIVE_PROBE */ - - ChipID = ReadDOC(window, ChipID); - - switch (ChipID) { - case DOC_ChipID_DocMilPlus16: - case DOC_ChipID_DocMilPlus32: - /* Check the TOGGLE bit in the toggle register */ - tmp = ReadDOC(window, Mplus_Toggle) & DOC_TOGGLE_BIT; - tmpb = ReadDOC(window, Mplus_Toggle) & DOC_TOGGLE_BIT; - tmpc = ReadDOC(window, Mplus_Toggle) & DOC_TOGGLE_BIT; - if (tmp != tmpb && tmp == tmpc) - return ChipID; - default: - break; - } - /* FALL TRHU */ - - default: - -#ifdef CONFIG_MTD_DOCPROBE_55AA - printk(KERN_DEBUG "Possible DiskOnChip with unknown ChipID %2.2X found at 0x%lx\n", - ChipID, physadr); -#endif -#ifndef DOC_PASSIVE_PROBE - /* Put back the contents of the DOCControl register, in case it's not - * actually a DiskOnChip. - */ - WriteDOC(tmp2, window, DOCControl); -#endif - return 0; - } - - printk(KERN_WARNING "DiskOnChip failed TOGGLE test, dropping.\n"); - -#ifndef DOC_PASSIVE_PROBE - /* Put back the contents of the DOCControl register: it's not a DiskOnChip */ - WriteDOC(tmp2, window, DOCControl); -#endif - return 0; -} - -static int docfound; - -extern void DoC2k_init(struct mtd_info *); -extern void DoCMil_init(struct mtd_info *); -extern void DoCMilPlus_init(struct mtd_info *); - -static void __init DoC_Probe(unsigned long physadr) -{ - void __iomem *docptr; - struct DiskOnChip *this; - struct mtd_info *mtd; - int ChipID; - char namebuf[15]; - char *name = namebuf; - void (*initroutine)(struct mtd_info *) = NULL; - - docptr = ioremap(physadr, DOC_IOREMAP_LEN); - - if (!docptr) - return; - - if ((ChipID = doccheck(docptr, physadr))) { - if (ChipID == DOC_ChipID_Doc2kTSOP) { - /* Remove this at your own peril. The hardware driver works but nothing prevents you from erasing bad blocks */ - printk(KERN_NOTICE "Refusing to drive DiskOnChip 2000 TSOP until Bad Block Table is correctly supported by INFTL\n"); - iounmap(docptr); - return; - } - docfound = 1; - mtd = kzalloc(sizeof(struct DiskOnChip) + sizeof(struct mtd_info), GFP_KERNEL); - if (!mtd) { - printk(KERN_WARNING "Cannot allocate memory for data structures. Dropping.\n"); - iounmap(docptr); - return; - } - - this = (struct DiskOnChip *)(&mtd[1]); - mtd->priv = this; - this->virtadr = docptr; - this->physadr = physadr; - this->ChipID = ChipID; - sprintf(namebuf, "with ChipID %2.2X", ChipID); - - switch(ChipID) { - case DOC_ChipID_Doc2kTSOP: - name="2000 TSOP"; - initroutine = symbol_request(DoC2k_init); - break; - - case DOC_ChipID_Doc2k: - name="2000"; - initroutine = symbol_request(DoC2k_init); - break; - - case DOC_ChipID_DocMil: - name="Millennium"; -#ifdef DOC_SINGLE_DRIVER - initroutine = symbol_request(DoC2k_init); -#else - initroutine = symbol_request(DoCMil_init); -#endif /* DOC_SINGLE_DRIVER */ - break; - - case DOC_ChipID_DocMilPlus16: - case DOC_ChipID_DocMilPlus32: - name="MillenniumPlus"; - initroutine = symbol_request(DoCMilPlus_init); - break; - } - - if (initroutine) { - (*initroutine)(mtd); - symbol_put_addr(initroutine); - return; - } - printk(KERN_NOTICE "Cannot find driver for DiskOnChip %s at 0x%lX\n", name, physadr); - kfree(mtd); - } - iounmap(docptr); -} - - -/**************************************************************************** - * - * Module stuff - * - ****************************************************************************/ - -static int __init init_doc(void) -{ - int i; - - if (doc_config_location) { - printk(KERN_INFO "Using configured DiskOnChip probe address 0x%lx\n", doc_config_location); - DoC_Probe(doc_config_location); - } else { - for (i=0; (doc_locations[i] != 0xffffffff); i++) { - DoC_Probe(doc_locations[i]); - } - } - /* No banner message any more. Print a message if no DiskOnChip - found, so the user knows we at least tried. */ - if (!docfound) - printk(KERN_INFO "No recognised DiskOnChip devices found\n"); - return -EAGAIN; -} - -module_init(init_doc); - -MODULE_LICENSE("GPL"); -MODULE_AUTHOR("David Woodhouse <dwmw2@infradead.org>"); -MODULE_DESCRIPTION("Probe code for DiskOnChip 2000 and Millennium devices"); - diff --git a/drivers/mtd/devices/elm.c b/drivers/mtd/devices/elm.c new file mode 100644 index 00000000000..b4f61c7fc16 --- /dev/null +++ b/drivers/mtd/devices/elm.c @@ -0,0 +1,579 @@ +/* + * Error Location Module + * + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#define DRIVER_NAME "omap-elm" + +#include <linux/platform_device.h> +#include <linux/module.h> +#include <linux/interrupt.h> +#include <linux/io.h> +#include <linux/of.h> +#include <linux/sched.h> +#include <linux/pm_runtime.h> +#include <linux/platform_data/elm.h> + +#define ELM_SYSCONFIG 0x010 +#define ELM_IRQSTATUS 0x018 +#define ELM_IRQENABLE 0x01c +#define ELM_LOCATION_CONFIG 0x020 +#define ELM_PAGE_CTRL 0x080 +#define ELM_SYNDROME_FRAGMENT_0 0x400 +#define ELM_SYNDROME_FRAGMENT_1 0x404 +#define ELM_SYNDROME_FRAGMENT_2 0x408 +#define ELM_SYNDROME_FRAGMENT_3 0x40c +#define ELM_SYNDROME_FRAGMENT_4 0x410 +#define ELM_SYNDROME_FRAGMENT_5 0x414 +#define ELM_SYNDROME_FRAGMENT_6 0x418 +#define ELM_LOCATION_STATUS 0x800 +#define ELM_ERROR_LOCATION_0 0x880 + +/* ELM Interrupt Status Register */ +#define INTR_STATUS_PAGE_VALID BIT(8) + +/* ELM Interrupt Enable Register */ +#define INTR_EN_PAGE_MASK BIT(8) + +/* ELM Location Configuration Register */ +#define ECC_BCH_LEVEL_MASK 0x3 + +/* ELM syndrome */ +#define ELM_SYNDROME_VALID BIT(16) + +/* ELM_LOCATION_STATUS Register */ +#define ECC_CORRECTABLE_MASK BIT(8) +#define ECC_NB_ERRORS_MASK 0x1f + +/* ELM_ERROR_LOCATION_0-15 Registers */ +#define ECC_ERROR_LOCATION_MASK 0x1fff + +#define ELM_ECC_SIZE 0x7ff + +#define SYNDROME_FRAGMENT_REG_SIZE 0x40 +#define ERROR_LOCATION_SIZE 0x100 + +struct elm_registers { + u32 elm_irqenable; + u32 elm_sysconfig; + u32 elm_location_config; + u32 elm_page_ctrl; + u32 elm_syndrome_fragment_6[ERROR_VECTOR_MAX]; + u32 elm_syndrome_fragment_5[ERROR_VECTOR_MAX]; + u32 elm_syndrome_fragment_4[ERROR_VECTOR_MAX]; + u32 elm_syndrome_fragment_3[ERROR_VECTOR_MAX]; + u32 elm_syndrome_fragment_2[ERROR_VECTOR_MAX]; + u32 elm_syndrome_fragment_1[ERROR_VECTOR_MAX]; + u32 elm_syndrome_fragment_0[ERROR_VECTOR_MAX]; +}; + +struct elm_info { + struct device *dev; + void __iomem *elm_base; + struct completion elm_completion; + struct list_head list; + enum bch_ecc bch_type; + struct elm_registers elm_regs; + int ecc_steps; + int ecc_syndrome_size; +}; + +static LIST_HEAD(elm_devices); + +static void elm_write_reg(struct elm_info *info, int offset, u32 val) +{ + writel(val, info->elm_base + offset); +} + +static u32 elm_read_reg(struct elm_info *info, int offset) +{ + return readl(info->elm_base + offset); +} + +/** + * elm_config - Configure ELM module + * @dev: ELM device + * @bch_type: Type of BCH ecc + */ +int elm_config(struct device *dev, enum bch_ecc bch_type, + int ecc_steps, int ecc_step_size, int ecc_syndrome_size) +{ + u32 reg_val; + struct elm_info *info = dev_get_drvdata(dev); + + if (!info) { + dev_err(dev, "Unable to configure elm - device not probed?\n"); + return -ENODEV; + } + /* ELM cannot detect ECC errors for chunks > 1KB */ + if (ecc_step_size > ((ELM_ECC_SIZE + 1) / 2)) { + dev_err(dev, "unsupported config ecc-size=%d\n", ecc_step_size); + return -EINVAL; + } + /* ELM support 8 error syndrome process */ + if (ecc_steps > ERROR_VECTOR_MAX) { + dev_err(dev, "unsupported config ecc-step=%d\n", ecc_steps); + return -EINVAL; + } + + reg_val = (bch_type & ECC_BCH_LEVEL_MASK) | (ELM_ECC_SIZE << 16); + elm_write_reg(info, ELM_LOCATION_CONFIG, reg_val); + info->bch_type = bch_type; + info->ecc_steps = ecc_steps; + info->ecc_syndrome_size = ecc_syndrome_size; + + return 0; +} +EXPORT_SYMBOL(elm_config); + +/** + * elm_configure_page_mode - Enable/Disable page mode + * @info: elm info + * @index: index number of syndrome fragment vector + * @enable: enable/disable flag for page mode + * + * Enable page mode for syndrome fragment index + */ +static void elm_configure_page_mode(struct elm_info *info, int index, + bool enable) +{ + u32 reg_val; + + reg_val = elm_read_reg(info, ELM_PAGE_CTRL); + if (enable) + reg_val |= BIT(index); /* enable page mode */ + else + reg_val &= ~BIT(index); /* disable page mode */ + + elm_write_reg(info, ELM_PAGE_CTRL, reg_val); +} + +/** + * elm_load_syndrome - Load ELM syndrome reg + * @info: elm info + * @err_vec: elm error vectors + * @ecc: buffer with calculated ecc + * + * Load syndrome fragment registers with calculated ecc in reverse order. + */ +static void elm_load_syndrome(struct elm_info *info, + struct elm_errorvec *err_vec, u8 *ecc) +{ + int i, offset; + u32 val; + + for (i = 0; i < info->ecc_steps; i++) { + + /* Check error reported */ + if (err_vec[i].error_reported) { + elm_configure_page_mode(info, i, true); + offset = ELM_SYNDROME_FRAGMENT_0 + + SYNDROME_FRAGMENT_REG_SIZE * i; + switch (info->bch_type) { + case BCH8_ECC: + /* syndrome fragment 0 = ecc[9-12B] */ + val = cpu_to_be32(*(u32 *) &ecc[9]); + elm_write_reg(info, offset, val); + + /* syndrome fragment 1 = ecc[5-8B] */ + offset += 4; + val = cpu_to_be32(*(u32 *) &ecc[5]); + elm_write_reg(info, offset, val); + + /* syndrome fragment 2 = ecc[1-4B] */ + offset += 4; + val = cpu_to_be32(*(u32 *) &ecc[1]); + elm_write_reg(info, offset, val); + + /* syndrome fragment 3 = ecc[0B] */ + offset += 4; + val = ecc[0]; + elm_write_reg(info, offset, val); + break; + case BCH4_ECC: + /* syndrome fragment 0 = ecc[20-52b] bits */ + val = (cpu_to_be32(*(u32 *) &ecc[3]) >> 4) | + ((ecc[2] & 0xf) << 28); + elm_write_reg(info, offset, val); + + /* syndrome fragment 1 = ecc[0-20b] bits */ + offset += 4; + val = cpu_to_be32(*(u32 *) &ecc[0]) >> 12; + elm_write_reg(info, offset, val); + break; + case BCH16_ECC: + val = cpu_to_be32(*(u32 *) &ecc[22]); + elm_write_reg(info, offset, val); + offset += 4; + val = cpu_to_be32(*(u32 *) &ecc[18]); + elm_write_reg(info, offset, val); + offset += 4; + val = cpu_to_be32(*(u32 *) &ecc[14]); + elm_write_reg(info, offset, val); + offset += 4; + val = cpu_to_be32(*(u32 *) &ecc[10]); + elm_write_reg(info, offset, val); + offset += 4; + val = cpu_to_be32(*(u32 *) &ecc[6]); + elm_write_reg(info, offset, val); + offset += 4; + val = cpu_to_be32(*(u32 *) &ecc[2]); + elm_write_reg(info, offset, val); + offset += 4; + val = cpu_to_be32(*(u32 *) &ecc[0]) >> 16; + elm_write_reg(info, offset, val); + break; + default: + pr_err("invalid config bch_type\n"); + } + } + + /* Update ecc pointer with ecc byte size */ + ecc += info->ecc_syndrome_size; + } +} + +/** + * elm_start_processing - start elm syndrome processing + * @info: elm info + * @err_vec: elm error vectors + * + * Set syndrome valid bit for syndrome fragment registers for which + * elm syndrome fragment registers are loaded. This enables elm module + * to start processing syndrome vectors. + */ +static void elm_start_processing(struct elm_info *info, + struct elm_errorvec *err_vec) +{ + int i, offset; + u32 reg_val; + + /* + * Set syndrome vector valid, so that ELM module + * will process it for vectors error is reported + */ + for (i = 0; i < info->ecc_steps; i++) { + if (err_vec[i].error_reported) { + offset = ELM_SYNDROME_FRAGMENT_6 + + SYNDROME_FRAGMENT_REG_SIZE * i; + reg_val = elm_read_reg(info, offset); + reg_val |= ELM_SYNDROME_VALID; + elm_write_reg(info, offset, reg_val); + } + } +} + +/** + * elm_error_correction - locate correctable error position + * @info: elm info + * @err_vec: elm error vectors + * + * On completion of processing by elm module, error location status + * register updated with correctable/uncorrectable error information. + * In case of correctable errors, number of errors located from + * elm location status register & read the positions from + * elm error location register. + */ +static void elm_error_correction(struct elm_info *info, + struct elm_errorvec *err_vec) +{ + int i, j, errors = 0; + int offset; + u32 reg_val; + + for (i = 0; i < info->ecc_steps; i++) { + + /* Check error reported */ + if (err_vec[i].error_reported) { + offset = ELM_LOCATION_STATUS + ERROR_LOCATION_SIZE * i; + reg_val = elm_read_reg(info, offset); + + /* Check correctable error or not */ + if (reg_val & ECC_CORRECTABLE_MASK) { + offset = ELM_ERROR_LOCATION_0 + + ERROR_LOCATION_SIZE * i; + + /* Read count of correctable errors */ + err_vec[i].error_count = reg_val & + ECC_NB_ERRORS_MASK; + + /* Update the error locations in error vector */ + for (j = 0; j < err_vec[i].error_count; j++) { + + reg_val = elm_read_reg(info, offset); + err_vec[i].error_loc[j] = reg_val & + ECC_ERROR_LOCATION_MASK; + + /* Update error location register */ + offset += 4; + } + + errors += err_vec[i].error_count; + } else { + err_vec[i].error_uncorrectable = true; + } + + /* Clearing interrupts for processed error vectors */ + elm_write_reg(info, ELM_IRQSTATUS, BIT(i)); + + /* Disable page mode */ + elm_configure_page_mode(info, i, false); + } + } +} + +/** + * elm_decode_bch_error_page - Locate error position + * @dev: device pointer + * @ecc_calc: calculated ECC bytes from GPMC + * @err_vec: elm error vectors + * + * Called with one or more error reported vectors & vectors with + * error reported is updated in err_vec[].error_reported + */ +void elm_decode_bch_error_page(struct device *dev, u8 *ecc_calc, + struct elm_errorvec *err_vec) +{ + struct elm_info *info = dev_get_drvdata(dev); + u32 reg_val; + + /* Enable page mode interrupt */ + reg_val = elm_read_reg(info, ELM_IRQSTATUS); + elm_write_reg(info, ELM_IRQSTATUS, reg_val & INTR_STATUS_PAGE_VALID); + elm_write_reg(info, ELM_IRQENABLE, INTR_EN_PAGE_MASK); + + /* Load valid ecc byte to syndrome fragment register */ + elm_load_syndrome(info, err_vec, ecc_calc); + + /* Enable syndrome processing for which syndrome fragment is updated */ + elm_start_processing(info, err_vec); + + /* Wait for ELM module to finish locating error correction */ + wait_for_completion(&info->elm_completion); + + /* Disable page mode interrupt */ + reg_val = elm_read_reg(info, ELM_IRQENABLE); + elm_write_reg(info, ELM_IRQENABLE, reg_val & ~INTR_EN_PAGE_MASK); + elm_error_correction(info, err_vec); +} +EXPORT_SYMBOL(elm_decode_bch_error_page); + +static irqreturn_t elm_isr(int this_irq, void *dev_id) +{ + u32 reg_val; + struct elm_info *info = dev_id; + + reg_val = elm_read_reg(info, ELM_IRQSTATUS); + + /* All error vectors processed */ + if (reg_val & INTR_STATUS_PAGE_VALID) { + elm_write_reg(info, ELM_IRQSTATUS, + reg_val & INTR_STATUS_PAGE_VALID); + complete(&info->elm_completion); + return IRQ_HANDLED; + } + + return IRQ_NONE; +} + +static int elm_probe(struct platform_device *pdev) +{ + int ret = 0; + struct resource *res, *irq; + struct elm_info *info; + + info = devm_kzalloc(&pdev->dev, sizeof(*info), GFP_KERNEL); + if (!info) + return -ENOMEM; + + info->dev = &pdev->dev; + + irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0); + if (!irq) { + dev_err(&pdev->dev, "no irq resource defined\n"); + return -ENODEV; + } + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + info->elm_base = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(info->elm_base)) + return PTR_ERR(info->elm_base); + + ret = devm_request_irq(&pdev->dev, irq->start, elm_isr, 0, + pdev->name, info); + if (ret) { + dev_err(&pdev->dev, "failure requesting irq %i\n", irq->start); + return ret; + } + + pm_runtime_enable(&pdev->dev); + if (pm_runtime_get_sync(&pdev->dev) < 0) { + ret = -EINVAL; + pm_runtime_disable(&pdev->dev); + dev_err(&pdev->dev, "can't enable clock\n"); + return ret; + } + + init_completion(&info->elm_completion); + INIT_LIST_HEAD(&info->list); + list_add(&info->list, &elm_devices); + platform_set_drvdata(pdev, info); + return ret; +} + +static int elm_remove(struct platform_device *pdev) +{ + pm_runtime_put_sync(&pdev->dev); + pm_runtime_disable(&pdev->dev); + return 0; +} + +#ifdef CONFIG_PM_SLEEP +/** + * elm_context_save + * saves ELM configurations to preserve them across Hardware powered-down + */ +static int elm_context_save(struct elm_info *info) +{ + struct elm_registers *regs = &info->elm_regs; + enum bch_ecc bch_type = info->bch_type; + u32 offset = 0, i; + + regs->elm_irqenable = elm_read_reg(info, ELM_IRQENABLE); + regs->elm_sysconfig = elm_read_reg(info, ELM_SYSCONFIG); + regs->elm_location_config = elm_read_reg(info, ELM_LOCATION_CONFIG); + regs->elm_page_ctrl = elm_read_reg(info, ELM_PAGE_CTRL); + for (i = 0; i < ERROR_VECTOR_MAX; i++) { + offset = i * SYNDROME_FRAGMENT_REG_SIZE; + switch (bch_type) { + case BCH16_ECC: + regs->elm_syndrome_fragment_6[i] = elm_read_reg(info, + ELM_SYNDROME_FRAGMENT_6 + offset); + regs->elm_syndrome_fragment_5[i] = elm_read_reg(info, + ELM_SYNDROME_FRAGMENT_5 + offset); + regs->elm_syndrome_fragment_4[i] = elm_read_reg(info, + ELM_SYNDROME_FRAGMENT_4 + offset); + case BCH8_ECC: + regs->elm_syndrome_fragment_3[i] = elm_read_reg(info, + ELM_SYNDROME_FRAGMENT_3 + offset); + regs->elm_syndrome_fragment_2[i] = elm_read_reg(info, + ELM_SYNDROME_FRAGMENT_2 + offset); + case BCH4_ECC: + regs->elm_syndrome_fragment_1[i] = elm_read_reg(info, + ELM_SYNDROME_FRAGMENT_1 + offset); + regs->elm_syndrome_fragment_0[i] = elm_read_reg(info, + ELM_SYNDROME_FRAGMENT_0 + offset); + break; + default: + return -EINVAL; + } + /* ELM SYNDROME_VALID bit in SYNDROME_FRAGMENT_6[] needs + * to be saved for all BCH schemes*/ + regs->elm_syndrome_fragment_6[i] = elm_read_reg(info, + ELM_SYNDROME_FRAGMENT_6 + offset); + } + return 0; +} + +/** + * elm_context_restore + * writes configurations saved duing power-down back into ELM registers + */ +static int elm_context_restore(struct elm_info *info) +{ + struct elm_registers *regs = &info->elm_regs; + enum bch_ecc bch_type = info->bch_type; + u32 offset = 0, i; + + elm_write_reg(info, ELM_IRQENABLE, regs->elm_irqenable); + elm_write_reg(info, ELM_SYSCONFIG, regs->elm_sysconfig); + elm_write_reg(info, ELM_LOCATION_CONFIG, regs->elm_location_config); + elm_write_reg(info, ELM_PAGE_CTRL, regs->elm_page_ctrl); + for (i = 0; i < ERROR_VECTOR_MAX; i++) { + offset = i * SYNDROME_FRAGMENT_REG_SIZE; + switch (bch_type) { + case BCH16_ECC: + elm_write_reg(info, ELM_SYNDROME_FRAGMENT_6 + offset, + regs->elm_syndrome_fragment_6[i]); + elm_write_reg(info, ELM_SYNDROME_FRAGMENT_5 + offset, + regs->elm_syndrome_fragment_5[i]); + elm_write_reg(info, ELM_SYNDROME_FRAGMENT_4 + offset, + regs->elm_syndrome_fragment_4[i]); + case BCH8_ECC: + elm_write_reg(info, ELM_SYNDROME_FRAGMENT_3 + offset, + regs->elm_syndrome_fragment_3[i]); + elm_write_reg(info, ELM_SYNDROME_FRAGMENT_2 + offset, + regs->elm_syndrome_fragment_2[i]); + case BCH4_ECC: + elm_write_reg(info, ELM_SYNDROME_FRAGMENT_1 + offset, + regs->elm_syndrome_fragment_1[i]); + elm_write_reg(info, ELM_SYNDROME_FRAGMENT_0 + offset, + regs->elm_syndrome_fragment_0[i]); + break; + default: + return -EINVAL; + } + /* ELM_SYNDROME_VALID bit to be set in last to trigger FSM */ + elm_write_reg(info, ELM_SYNDROME_FRAGMENT_6 + offset, + regs->elm_syndrome_fragment_6[i] & + ELM_SYNDROME_VALID); + } + return 0; +} + +static int elm_suspend(struct device *dev) +{ + struct elm_info *info = dev_get_drvdata(dev); + elm_context_save(info); + pm_runtime_put_sync(dev); + return 0; +} + +static int elm_resume(struct device *dev) +{ + struct elm_info *info = dev_get_drvdata(dev); + pm_runtime_get_sync(dev); + elm_context_restore(info); + return 0; +} +#endif + +static SIMPLE_DEV_PM_OPS(elm_pm_ops, elm_suspend, elm_resume); + +#ifdef CONFIG_OF +static const struct of_device_id elm_of_match[] = { + { .compatible = "ti,am3352-elm" }, + {}, +}; +MODULE_DEVICE_TABLE(of, elm_of_match); +#endif + +static struct platform_driver elm_driver = { + .driver = { + .name = DRIVER_NAME, + .owner = THIS_MODULE, + .of_match_table = of_match_ptr(elm_of_match), + .pm = &elm_pm_ops, + }, + .probe = elm_probe, + .remove = elm_remove, +}; + +module_platform_driver(elm_driver); + +MODULE_DESCRIPTION("ELM driver for BCH error correction"); +MODULE_AUTHOR("Texas Instruments"); +MODULE_ALIAS("platform: elm"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/mtd/devices/lart.c b/drivers/mtd/devices/lart.c index 3a11ea628e5..82bd00af5cc 100644 --- a/drivers/mtd/devices/lart.c +++ b/drivers/mtd/devices/lart.c @@ -367,9 +367,6 @@ static int flash_erase (struct mtd_info *mtd,struct erase_info *instr) printk (KERN_DEBUG "%s(addr = 0x%.8x, len = %d)\n", __func__, instr->addr, instr->len); #endif - /* sanity checks */ - if (instr->addr + instr->len > mtd->size) return (-EINVAL); - /* * check that both start and end of the requested erase are * aligned with the erasesize at the appropriate addresses. @@ -440,10 +437,6 @@ static int flash_read (struct mtd_info *mtd,loff_t from,size_t len,size_t *retle printk (KERN_DEBUG "%s(from = 0x%.8x, len = %d)\n", __func__, (__u32)from, len); #endif - /* sanity checks */ - if (!len) return (0); - if (from + len > mtd->size) return (-EINVAL); - /* we always read len bytes */ *retlen = len; @@ -522,11 +515,8 @@ static int flash_write (struct mtd_info *mtd,loff_t to,size_t len,size_t *retlen printk (KERN_DEBUG "%s(to = 0x%.8x, len = %d)\n", __func__, (__u32)to, len); #endif - *retlen = 0; - /* sanity checks */ if (!len) return (0); - if (to + len > mtd->size) return (-EINVAL); /* first, we write a 0xFF.... padded byte until we reach a dword boundary */ if (to & (BUSWIDTH - 1)) @@ -630,14 +620,15 @@ static int __init lart_flash_init (void) mtd.name = module_name; mtd.type = MTD_NORFLASH; mtd.writesize = 1; + mtd.writebufsize = 4; mtd.flags = MTD_CAP_NORFLASH; mtd.size = FLASH_BLOCKSIZE_PARAM * FLASH_NUMBLOCKS_16m_PARAM + FLASH_BLOCKSIZE_MAIN * FLASH_NUMBLOCKS_16m_MAIN; mtd.erasesize = FLASH_BLOCKSIZE_MAIN; mtd.numeraseregions = ARRAY_SIZE(erase_regions); mtd.eraseregions = erase_regions; - mtd.erase = flash_erase; - mtd.read = flash_read; - mtd.write = flash_write; + mtd._erase = flash_erase; + mtd._read = flash_read; + mtd._write = flash_write; mtd.owner = THIS_MODULE; #ifdef LART_DEBUG diff --git a/drivers/mtd/devices/m25p80.c b/drivers/mtd/devices/m25p80.c index 7c60dddbefc..ed7e0a1bed3 100644 --- a/drivers/mtd/devices/m25p80.c +++ b/drivers/mtd/devices/m25p80.c @@ -15,977 +15,233 @@ * */ -#include <linux/init.h> #include <linux/err.h> #include <linux/errno.h> #include <linux/module.h> #include <linux/device.h> -#include <linux/interrupt.h> -#include <linux/mutex.h> -#include <linux/math64.h> -#include <linux/slab.h> -#include <linux/sched.h> -#include <linux/mod_devicetable.h> -#include <linux/mtd/cfi.h> #include <linux/mtd/mtd.h> #include <linux/mtd/partitions.h> -#include <linux/of_platform.h> #include <linux/spi/spi.h> #include <linux/spi/flash.h> +#include <linux/mtd/spi-nor.h> -/* Flash opcodes. */ -#define OPCODE_WREN 0x06 /* Write enable */ -#define OPCODE_RDSR 0x05 /* Read status register */ -#define OPCODE_WRSR 0x01 /* Write status register 1 byte */ -#define OPCODE_NORM_READ 0x03 /* Read data bytes (low frequency) */ -#define OPCODE_FAST_READ 0x0b /* Read data bytes (high frequency) */ -#define OPCODE_PP 0x02 /* Page program (up to 256 bytes) */ -#define OPCODE_BE_4K 0x20 /* Erase 4KiB block */ -#define OPCODE_BE_32K 0x52 /* Erase 32KiB block */ -#define OPCODE_CHIP_ERASE 0xc7 /* Erase whole flash chip */ -#define OPCODE_SE 0xd8 /* Sector erase (usually 64KiB) */ -#define OPCODE_RDID 0x9f /* Read JEDEC ID */ - -/* Used for SST flashes only. */ -#define OPCODE_BP 0x02 /* Byte program */ -#define OPCODE_WRDI 0x04 /* Write disable */ -#define OPCODE_AAI_WP 0xad /* Auto address increment word program */ - -/* Used for Macronix flashes only. */ -#define OPCODE_EN4B 0xb7 /* Enter 4-byte mode */ -#define OPCODE_EX4B 0xe9 /* Exit 4-byte mode */ - -/* Used for Spansion flashes only. */ -#define OPCODE_BRWR 0x17 /* Bank register write */ - -/* Status Register bits. */ -#define SR_WIP 1 /* Write in progress */ -#define SR_WEL 2 /* Write enable latch */ -/* meaning of other SR_* bits may differ between vendors */ -#define SR_BP0 4 /* Block protect 0 */ -#define SR_BP1 8 /* Block protect 1 */ -#define SR_BP2 0x10 /* Block protect 2 */ -#define SR_SRWD 0x80 /* SR write protect */ - -/* Define max times to check status register before we give up. */ -#define MAX_READY_WAIT_JIFFIES (40 * HZ) /* M25P16 specs 40s max chip erase */ -#define MAX_CMD_SIZE 5 - -#ifdef CONFIG_M25PXX_USE_FAST_READ -#define OPCODE_READ OPCODE_FAST_READ -#define FAST_READ_DUMMY_BYTE 1 -#else -#define OPCODE_READ OPCODE_NORM_READ -#define FAST_READ_DUMMY_BYTE 0 -#endif - -#define JEDEC_MFR(_jedec_id) ((_jedec_id) >> 16) - -/****************************************************************************/ - +#define MAX_CMD_SIZE 6 struct m25p { struct spi_device *spi; - struct mutex lock; + struct spi_nor spi_nor; struct mtd_info mtd; - u16 page_size; - u16 addr_width; - u8 erase_opcode; - u8 *command; + u8 command[MAX_CMD_SIZE]; }; -static inline struct m25p *mtd_to_m25p(struct mtd_info *mtd) -{ - return container_of(mtd, struct m25p, mtd); -} - -/****************************************************************************/ - -/* - * Internal helper functions - */ - -/* - * Read the status register, returning its value in the location - * Return the status register value. - * Returns negative if error occurred. - */ -static int read_sr(struct m25p *flash) -{ - ssize_t retval; - u8 code = OPCODE_RDSR; - u8 val; - - retval = spi_write_then_read(flash->spi, &code, 1, &val, 1); - - if (retval < 0) { - dev_err(&flash->spi->dev, "error %d reading SR\n", - (int) retval); - return retval; - } - - return val; -} - -/* - * Write status register 1 byte - * Returns negative if error occurred. - */ -static int write_sr(struct m25p *flash, u8 val) -{ - flash->command[0] = OPCODE_WRSR; - flash->command[1] = val; - - return spi_write(flash->spi, flash->command, 2); -} - -/* - * Set write enable latch with Write Enable command. - * Returns negative if error occurred. - */ -static inline int write_enable(struct m25p *flash) -{ - u8 code = OPCODE_WREN; - - return spi_write_then_read(flash->spi, &code, 1, NULL, 0); -} - -/* - * Send write disble instruction to the chip. - */ -static inline int write_disable(struct m25p *flash) -{ - u8 code = OPCODE_WRDI; - - return spi_write_then_read(flash->spi, &code, 1, NULL, 0); -} - -/* - * Enable/disable 4-byte addressing mode. - */ -static inline int set_4byte(struct m25p *flash, u32 jedec_id, int enable) -{ - switch (JEDEC_MFR(jedec_id)) { - case CFI_MFR_MACRONIX: - flash->command[0] = enable ? OPCODE_EN4B : OPCODE_EX4B; - return spi_write(flash->spi, flash->command, 1); - default: - /* Spansion style */ - flash->command[0] = OPCODE_BRWR; - flash->command[1] = enable << 7; - return spi_write(flash->spi, flash->command, 2); - } -} - -/* - * Service routine to read status register until ready, or timeout occurs. - * Returns non-zero if error. - */ -static int wait_till_ready(struct m25p *flash) -{ - unsigned long deadline; - int sr; - - deadline = jiffies + MAX_READY_WAIT_JIFFIES; - - do { - if ((sr = read_sr(flash)) < 0) - break; - else if (!(sr & SR_WIP)) - return 0; - - cond_resched(); - - } while (!time_after_eq(jiffies, deadline)); - - return 1; -} - -/* - * Erase the whole flash memory - * - * Returns 0 if successful, non-zero otherwise. - */ -static int erase_chip(struct m25p *flash) +static int m25p80_read_reg(struct spi_nor *nor, u8 code, u8 *val, int len) { - pr_debug("%s: %s %lldKiB\n", dev_name(&flash->spi->dev), __func__, - (long long)(flash->mtd.size >> 10)); - - /* Wait until finished previous write command. */ - if (wait_till_ready(flash)) - return 1; - - /* Send write enable, then erase commands. */ - write_enable(flash); - - /* Set up command buffer. */ - flash->command[0] = OPCODE_CHIP_ERASE; + struct m25p *flash = nor->priv; + struct spi_device *spi = flash->spi; + int ret; - spi_write(flash->spi, flash->command, 1); + ret = spi_write_then_read(spi, &code, 1, val, len); + if (ret < 0) + dev_err(&spi->dev, "error %d reading %x\n", ret, code); - return 0; + return ret; } -static void m25p_addr2cmd(struct m25p *flash, unsigned int addr, u8 *cmd) +static void m25p_addr2cmd(struct spi_nor *nor, unsigned int addr, u8 *cmd) { /* opcode is in cmd[0] */ - cmd[1] = addr >> (flash->addr_width * 8 - 8); - cmd[2] = addr >> (flash->addr_width * 8 - 16); - cmd[3] = addr >> (flash->addr_width * 8 - 24); - cmd[4] = addr >> (flash->addr_width * 8 - 32); + cmd[1] = addr >> (nor->addr_width * 8 - 8); + cmd[2] = addr >> (nor->addr_width * 8 - 16); + cmd[3] = addr >> (nor->addr_width * 8 - 24); + cmd[4] = addr >> (nor->addr_width * 8 - 32); } -static int m25p_cmdsz(struct m25p *flash) -{ - return 1 + flash->addr_width; -} - -/* - * Erase one sector of flash memory at offset ``offset'' which is any - * address within the sector which should be erased. - * - * Returns 0 if successful, non-zero otherwise. - */ -static int erase_sector(struct m25p *flash, u32 offset) +static int m25p_cmdsz(struct spi_nor *nor) { - pr_debug("%s: %s %dKiB at 0x%08x\n", dev_name(&flash->spi->dev), - __func__, flash->mtd.erasesize / 1024, offset); - - /* Wait until finished previous write command. */ - if (wait_till_ready(flash)) - return 1; - - /* Send write enable, then erase commands. */ - write_enable(flash); - - /* Set up command buffer. */ - flash->command[0] = flash->erase_opcode; - m25p_addr2cmd(flash, offset, flash->command); - - spi_write(flash->spi, flash->command, m25p_cmdsz(flash)); - - return 0; + return 1 + nor->addr_width; } -/****************************************************************************/ - -/* - * MTD implementation - */ - -/* - * Erase an address range on the flash chip. The address range may extend - * one or more erase sectors. Return an error is there is a problem erasing. - */ -static int m25p80_erase(struct mtd_info *mtd, struct erase_info *instr) +static int m25p80_write_reg(struct spi_nor *nor, u8 opcode, u8 *buf, int len, + int wr_en) { - struct m25p *flash = mtd_to_m25p(mtd); - u32 addr,len; - uint32_t rem; - - pr_debug("%s: %s at 0x%llx, len %lld\n", dev_name(&flash->spi->dev), - __func__, (long long)instr->addr, - (long long)instr->len); - - /* sanity checks */ - if (instr->addr + instr->len > flash->mtd.size) - return -EINVAL; - div_u64_rem(instr->len, mtd->erasesize, &rem); - if (rem) - return -EINVAL; - - addr = instr->addr; - len = instr->len; - - mutex_lock(&flash->lock); - - /* whole-chip erase? */ - if (len == flash->mtd.size) { - if (erase_chip(flash)) { - instr->state = MTD_ERASE_FAILED; - mutex_unlock(&flash->lock); - return -EIO; - } - - /* REVISIT in some cases we could speed up erasing large regions - * by using OPCODE_SE instead of OPCODE_BE_4K. We may have set up - * to use "small sector erase", but that's not always optimal. - */ - - /* "sector"-at-a-time erase */ - } else { - while (len) { - if (erase_sector(flash, addr)) { - instr->state = MTD_ERASE_FAILED; - mutex_unlock(&flash->lock); - return -EIO; - } - - addr += mtd->erasesize; - len -= mtd->erasesize; - } - } + struct m25p *flash = nor->priv; + struct spi_device *spi = flash->spi; - mutex_unlock(&flash->lock); + flash->command[0] = opcode; + if (buf) + memcpy(&flash->command[1], buf, len); - instr->state = MTD_ERASE_DONE; - mtd_erase_callback(instr); - - return 0; + return spi_write(spi, flash->command, len + 1); } -/* - * Read an address range from the flash chip. The address range - * may be any size provided it is within the physical boundaries. - */ -static int m25p80_read(struct mtd_info *mtd, loff_t from, size_t len, - size_t *retlen, u_char *buf) +static void m25p80_write(struct spi_nor *nor, loff_t to, size_t len, + size_t *retlen, const u_char *buf) { - struct m25p *flash = mtd_to_m25p(mtd); - struct spi_transfer t[2]; + struct m25p *flash = nor->priv; + struct spi_device *spi = flash->spi; + struct spi_transfer t[2] = {}; struct spi_message m; + int cmd_sz = m25p_cmdsz(nor); - pr_debug("%s: %s from 0x%08x, len %zd\n", dev_name(&flash->spi->dev), - __func__, (u32)from, len); - - /* sanity checks */ - if (!len) - return 0; + spi_message_init(&m); - if (from + len > flash->mtd.size) - return -EINVAL; + if (nor->program_opcode == SPINOR_OP_AAI_WP && nor->sst_write_second) + cmd_sz = 1; - spi_message_init(&m); - memset(t, 0, (sizeof t)); + flash->command[0] = nor->program_opcode; + m25p_addr2cmd(nor, to, flash->command); - /* NOTE: - * OPCODE_FAST_READ (if available) is faster. - * Should add 1 byte DUMMY_BYTE. - */ t[0].tx_buf = flash->command; - t[0].len = m25p_cmdsz(flash) + FAST_READ_DUMMY_BYTE; + t[0].len = cmd_sz; spi_message_add_tail(&t[0], &m); - t[1].rx_buf = buf; + t[1].tx_buf = buf; t[1].len = len; spi_message_add_tail(&t[1], &m); - /* Byte count starts at zero. */ - *retlen = 0; + spi_sync(spi, &m); - mutex_lock(&flash->lock); + *retlen += m.actual_length - cmd_sz; +} - /* Wait till previous write/erase is done. */ - if (wait_till_ready(flash)) { - /* REVISIT status return?? */ - mutex_unlock(&flash->lock); - return 1; +static inline unsigned int m25p80_rx_nbits(struct spi_nor *nor) +{ + switch (nor->flash_read) { + case SPI_NOR_DUAL: + return 2; + case SPI_NOR_QUAD: + return 4; + default: + return 0; } - - /* FIXME switch to OPCODE_FAST_READ. It's required for higher - * clocks; and at this writing, every chip this driver handles - * supports that opcode. - */ - - /* Set up the write data buffer. */ - flash->command[0] = OPCODE_READ; - m25p_addr2cmd(flash, from, flash->command); - - spi_sync(flash->spi, &m); - - *retlen = m.actual_length - m25p_cmdsz(flash) - FAST_READ_DUMMY_BYTE; - - mutex_unlock(&flash->lock); - - return 0; } /* - * Write an address range to the flash chip. Data must be written in - * FLASH_PAGESIZE chunks. The address range may be any size provided - * it is within the physical boundaries. + * Read an address range from the nor chip. The address range + * may be any size provided it is within the physical boundaries. */ -static int m25p80_write(struct mtd_info *mtd, loff_t to, size_t len, - size_t *retlen, const u_char *buf) +static int m25p80_read(struct spi_nor *nor, loff_t from, size_t len, + size_t *retlen, u_char *buf) { - struct m25p *flash = mtd_to_m25p(mtd); - u32 page_offset, page_size; + struct m25p *flash = nor->priv; + struct spi_device *spi = flash->spi; struct spi_transfer t[2]; struct spi_message m; + int dummy = nor->read_dummy; + int ret; - pr_debug("%s: %s to 0x%08x, len %zd\n", dev_name(&flash->spi->dev), - __func__, (u32)to, len); - - *retlen = 0; - - /* sanity checks */ - if (!len) - return(0); - - if (to + len > flash->mtd.size) - return -EINVAL; + /* Wait till previous write/erase is done. */ + ret = nor->wait_till_ready(nor); + if (ret) + return ret; spi_message_init(&m); memset(t, 0, (sizeof t)); + flash->command[0] = nor->read_opcode; + m25p_addr2cmd(nor, from, flash->command); + t[0].tx_buf = flash->command; - t[0].len = m25p_cmdsz(flash); + t[0].len = m25p_cmdsz(nor) + dummy; spi_message_add_tail(&t[0], &m); - t[1].tx_buf = buf; + t[1].rx_buf = buf; + t[1].rx_nbits = m25p80_rx_nbits(nor); + t[1].len = len; spi_message_add_tail(&t[1], &m); - mutex_lock(&flash->lock); - - /* Wait until finished previous write command. */ - if (wait_till_ready(flash)) { - mutex_unlock(&flash->lock); - return 1; - } - - write_enable(flash); - - /* Set up the opcode in the write buffer. */ - flash->command[0] = OPCODE_PP; - m25p_addr2cmd(flash, to, flash->command); - - page_offset = to & (flash->page_size - 1); - - /* do all the bytes fit onto one page? */ - if (page_offset + len <= flash->page_size) { - t[1].len = len; - - spi_sync(flash->spi, &m); - - *retlen = m.actual_length - m25p_cmdsz(flash); - } else { - u32 i; - - /* the size of data remaining on the first page */ - page_size = flash->page_size - page_offset; - - t[1].len = page_size; - spi_sync(flash->spi, &m); - - *retlen = m.actual_length - m25p_cmdsz(flash); - - /* write everything in flash->page_size chunks */ - for (i = page_size; i < len; i += page_size) { - page_size = len - i; - if (page_size > flash->page_size) - page_size = flash->page_size; - - /* write the next page to flash */ - m25p_addr2cmd(flash, to + i, flash->command); - - t[1].tx_buf = buf + i; - t[1].len = page_size; - - wait_till_ready(flash); - - write_enable(flash); - - spi_sync(flash->spi, &m); - - *retlen += m.actual_length - m25p_cmdsz(flash); - } - } - - mutex_unlock(&flash->lock); + spi_sync(spi, &m); + *retlen = m.actual_length - m25p_cmdsz(nor) - dummy; return 0; } -static int sst_write(struct mtd_info *mtd, loff_t to, size_t len, - size_t *retlen, const u_char *buf) +static int m25p80_erase(struct spi_nor *nor, loff_t offset) { - struct m25p *flash = mtd_to_m25p(mtd); - struct spi_transfer t[2]; - struct spi_message m; - size_t actual; - int cmd_sz, ret; - - pr_debug("%s: %s to 0x%08x, len %zd\n", dev_name(&flash->spi->dev), - __func__, (u32)to, len); - - *retlen = 0; - - /* sanity checks */ - if (!len) - return 0; - - if (to + len > flash->mtd.size) - return -EINVAL; - - spi_message_init(&m); - memset(t, 0, (sizeof t)); + struct m25p *flash = nor->priv; + int ret; - t[0].tx_buf = flash->command; - t[0].len = m25p_cmdsz(flash); - spi_message_add_tail(&t[0], &m); - - t[1].tx_buf = buf; - spi_message_add_tail(&t[1], &m); - - mutex_lock(&flash->lock); + dev_dbg(nor->dev, "%dKiB at 0x%08x\n", + flash->mtd.erasesize / 1024, (u32)offset); /* Wait until finished previous write command. */ - ret = wait_till_ready(flash); + ret = nor->wait_till_ready(nor); if (ret) - goto time_out; - - write_enable(flash); - - actual = to % 2; - /* Start write from odd address. */ - if (actual) { - flash->command[0] = OPCODE_BP; - m25p_addr2cmd(flash, to, flash->command); + return ret; - /* write one byte. */ - t[1].len = 1; - spi_sync(flash->spi, &m); - ret = wait_till_ready(flash); - if (ret) - goto time_out; - *retlen += m.actual_length - m25p_cmdsz(flash); - } - to += actual; - - flash->command[0] = OPCODE_AAI_WP; - m25p_addr2cmd(flash, to, flash->command); - - /* Write out most of the data here. */ - cmd_sz = m25p_cmdsz(flash); - for (; actual < len - 1; actual += 2) { - t[0].len = cmd_sz; - /* write two bytes. */ - t[1].len = 2; - t[1].tx_buf = buf + actual; - - spi_sync(flash->spi, &m); - ret = wait_till_ready(flash); - if (ret) - goto time_out; - *retlen += m.actual_length - cmd_sz; - cmd_sz = 1; - to += 2; - } - write_disable(flash); - ret = wait_till_ready(flash); + /* Send write enable, then erase commands. */ + ret = nor->write_reg(nor, SPINOR_OP_WREN, NULL, 0, 0); if (ret) - goto time_out; - - /* Write out trailing byte if it exists. */ - if (actual != len) { - write_enable(flash); - flash->command[0] = OPCODE_BP; - m25p_addr2cmd(flash, to, flash->command); - t[0].len = m25p_cmdsz(flash); - t[1].len = 1; - t[1].tx_buf = buf + actual; - - spi_sync(flash->spi, &m); - ret = wait_till_ready(flash); - if (ret) - goto time_out; - *retlen += m.actual_length - m25p_cmdsz(flash); - write_disable(flash); - } - -time_out: - mutex_unlock(&flash->lock); - return ret; -} - -/****************************************************************************/ - -/* - * SPI device driver setup and teardown - */ - -struct flash_info { - /* JEDEC id zero means "no ID" (most older chips); otherwise it has - * a high byte of zero plus three data bytes: the manufacturer id, - * then a two byte device id. - */ - u32 jedec_id; - u16 ext_id; - - /* The size listed here is what works with OPCODE_SE, which isn't - * necessarily called a "sector" by the vendor. - */ - unsigned sector_size; - u16 n_sectors; - - u16 page_size; - u16 addr_width; - - u16 flags; -#define SECT_4K 0x01 /* OPCODE_BE_4K works uniformly */ -#define M25P_NO_ERASE 0x02 /* No erase command needed */ -}; - -#define INFO(_jedec_id, _ext_id, _sector_size, _n_sectors, _flags) \ - ((kernel_ulong_t)&(struct flash_info) { \ - .jedec_id = (_jedec_id), \ - .ext_id = (_ext_id), \ - .sector_size = (_sector_size), \ - .n_sectors = (_n_sectors), \ - .page_size = 256, \ - .flags = (_flags), \ - }) + return ret; -#define CAT25_INFO(_sector_size, _n_sectors, _page_size, _addr_width) \ - ((kernel_ulong_t)&(struct flash_info) { \ - .sector_size = (_sector_size), \ - .n_sectors = (_n_sectors), \ - .page_size = (_page_size), \ - .addr_width = (_addr_width), \ - .flags = M25P_NO_ERASE, \ - }) - -/* NOTE: double check command sets and memory organization when you add - * more flash chips. This current list focusses on newer chips, which - * have been converging on command sets which including JEDEC ID. - */ -static const struct spi_device_id m25p_ids[] = { - /* Atmel -- some are (confusingly) marketed as "DataFlash" */ - { "at25fs010", INFO(0x1f6601, 0, 32 * 1024, 4, SECT_4K) }, - { "at25fs040", INFO(0x1f6604, 0, 64 * 1024, 8, SECT_4K) }, - - { "at25df041a", INFO(0x1f4401, 0, 64 * 1024, 8, SECT_4K) }, - { "at25df321a", INFO(0x1f4701, 0, 64 * 1024, 64, SECT_4K) }, - { "at25df641", INFO(0x1f4800, 0, 64 * 1024, 128, SECT_4K) }, - - { "at26f004", INFO(0x1f0400, 0, 64 * 1024, 8, SECT_4K) }, - { "at26df081a", INFO(0x1f4501, 0, 64 * 1024, 16, SECT_4K) }, - { "at26df161a", INFO(0x1f4601, 0, 64 * 1024, 32, SECT_4K) }, - { "at26df321", INFO(0x1f4700, 0, 64 * 1024, 64, SECT_4K) }, - - /* EON -- en25xxx */ - { "en25f32", INFO(0x1c3116, 0, 64 * 1024, 64, SECT_4K) }, - { "en25p32", INFO(0x1c2016, 0, 64 * 1024, 64, 0) }, - { "en25q32b", INFO(0x1c3016, 0, 64 * 1024, 64, 0) }, - { "en25p64", INFO(0x1c2017, 0, 64 * 1024, 128, 0) }, - - /* Intel/Numonyx -- xxxs33b */ - { "160s33b", INFO(0x898911, 0, 64 * 1024, 32, 0) }, - { "320s33b", INFO(0x898912, 0, 64 * 1024, 64, 0) }, - { "640s33b", INFO(0x898913, 0, 64 * 1024, 128, 0) }, - - /* Macronix */ - { "mx25l4005a", INFO(0xc22013, 0, 64 * 1024, 8, SECT_4K) }, - { "mx25l8005", INFO(0xc22014, 0, 64 * 1024, 16, 0) }, - { "mx25l1606e", INFO(0xc22015, 0, 64 * 1024, 32, SECT_4K) }, - { "mx25l3205d", INFO(0xc22016, 0, 64 * 1024, 64, 0) }, - { "mx25l6405d", INFO(0xc22017, 0, 64 * 1024, 128, 0) }, - { "mx25l12805d", INFO(0xc22018, 0, 64 * 1024, 256, 0) }, - { "mx25l12855e", INFO(0xc22618, 0, 64 * 1024, 256, 0) }, - { "mx25l25635e", INFO(0xc22019, 0, 64 * 1024, 512, 0) }, - { "mx25l25655e", INFO(0xc22619, 0, 64 * 1024, 512, 0) }, - - /* Spansion -- single (large) sector size only, at least - * for the chips listed here (without boot sectors). - */ - { "s25sl004a", INFO(0x010212, 0, 64 * 1024, 8, 0) }, - { "s25sl008a", INFO(0x010213, 0, 64 * 1024, 16, 0) }, - { "s25sl016a", INFO(0x010214, 0, 64 * 1024, 32, 0) }, - { "s25sl032a", INFO(0x010215, 0, 64 * 1024, 64, 0) }, - { "s25sl032p", INFO(0x010215, 0x4d00, 64 * 1024, 64, SECT_4K) }, - { "s25sl064a", INFO(0x010216, 0, 64 * 1024, 128, 0) }, - { "s25fl256s0", INFO(0x010219, 0x4d00, 256 * 1024, 128, 0) }, - { "s25fl256s1", INFO(0x010219, 0x4d01, 64 * 1024, 512, 0) }, - { "s25fl512s", INFO(0x010220, 0x4d00, 256 * 1024, 256, 0) }, - { "s70fl01gs", INFO(0x010221, 0x4d00, 256 * 1024, 256, 0) }, - { "s25sl12800", INFO(0x012018, 0x0300, 256 * 1024, 64, 0) }, - { "s25sl12801", INFO(0x012018, 0x0301, 64 * 1024, 256, 0) }, - { "s25fl129p0", INFO(0x012018, 0x4d00, 256 * 1024, 64, 0) }, - { "s25fl129p1", INFO(0x012018, 0x4d01, 64 * 1024, 256, 0) }, - { "s25fl016k", INFO(0xef4015, 0, 64 * 1024, 32, SECT_4K) }, - { "s25fl064k", INFO(0xef4017, 0, 64 * 1024, 128, SECT_4K) }, - - /* SST -- large erase sizes are "overlays", "sectors" are 4K */ - { "sst25vf040b", INFO(0xbf258d, 0, 64 * 1024, 8, SECT_4K) }, - { "sst25vf080b", INFO(0xbf258e, 0, 64 * 1024, 16, SECT_4K) }, - { "sst25vf016b", INFO(0xbf2541, 0, 64 * 1024, 32, SECT_4K) }, - { "sst25vf032b", INFO(0xbf254a, 0, 64 * 1024, 64, SECT_4K) }, - { "sst25wf512", INFO(0xbf2501, 0, 64 * 1024, 1, SECT_4K) }, - { "sst25wf010", INFO(0xbf2502, 0, 64 * 1024, 2, SECT_4K) }, - { "sst25wf020", INFO(0xbf2503, 0, 64 * 1024, 4, SECT_4K) }, - { "sst25wf040", INFO(0xbf2504, 0, 64 * 1024, 8, SECT_4K) }, - - /* ST Microelectronics -- newer production may have feature updates */ - { "m25p05", INFO(0x202010, 0, 32 * 1024, 2, 0) }, - { "m25p10", INFO(0x202011, 0, 32 * 1024, 4, 0) }, - { "m25p20", INFO(0x202012, 0, 64 * 1024, 4, 0) }, - { "m25p40", INFO(0x202013, 0, 64 * 1024, 8, 0) }, - { "m25p80", INFO(0x202014, 0, 64 * 1024, 16, 0) }, - { "m25p16", INFO(0x202015, 0, 64 * 1024, 32, 0) }, - { "m25p32", INFO(0x202016, 0, 64 * 1024, 64, 0) }, - { "m25p64", INFO(0x202017, 0, 64 * 1024, 128, 0) }, - { "m25p128", INFO(0x202018, 0, 256 * 1024, 64, 0) }, - - { "m25p05-nonjedec", INFO(0, 0, 32 * 1024, 2, 0) }, - { "m25p10-nonjedec", INFO(0, 0, 32 * 1024, 4, 0) }, - { "m25p20-nonjedec", INFO(0, 0, 64 * 1024, 4, 0) }, - { "m25p40-nonjedec", INFO(0, 0, 64 * 1024, 8, 0) }, - { "m25p80-nonjedec", INFO(0, 0, 64 * 1024, 16, 0) }, - { "m25p16-nonjedec", INFO(0, 0, 64 * 1024, 32, 0) }, - { "m25p32-nonjedec", INFO(0, 0, 64 * 1024, 64, 0) }, - { "m25p64-nonjedec", INFO(0, 0, 64 * 1024, 128, 0) }, - { "m25p128-nonjedec", INFO(0, 0, 256 * 1024, 64, 0) }, - - { "m45pe10", INFO(0x204011, 0, 64 * 1024, 2, 0) }, - { "m45pe80", INFO(0x204014, 0, 64 * 1024, 16, 0) }, - { "m45pe16", INFO(0x204015, 0, 64 * 1024, 32, 0) }, - - { "m25pe80", INFO(0x208014, 0, 64 * 1024, 16, 0) }, - { "m25pe16", INFO(0x208015, 0, 64 * 1024, 32, SECT_4K) }, - - { "m25px32", INFO(0x207116, 0, 64 * 1024, 64, SECT_4K) }, - { "m25px32-s0", INFO(0x207316, 0, 64 * 1024, 64, SECT_4K) }, - { "m25px32-s1", INFO(0x206316, 0, 64 * 1024, 64, SECT_4K) }, - { "m25px64", INFO(0x207117, 0, 64 * 1024, 128, 0) }, - - /* Winbond -- w25x "blocks" are 64K, "sectors" are 4KiB */ - { "w25x10", INFO(0xef3011, 0, 64 * 1024, 2, SECT_4K) }, - { "w25x20", INFO(0xef3012, 0, 64 * 1024, 4, SECT_4K) }, - { "w25x40", INFO(0xef3013, 0, 64 * 1024, 8, SECT_4K) }, - { "w25x80", INFO(0xef3014, 0, 64 * 1024, 16, SECT_4K) }, - { "w25x16", INFO(0xef3015, 0, 64 * 1024, 32, SECT_4K) }, - { "w25x32", INFO(0xef3016, 0, 64 * 1024, 64, SECT_4K) }, - { "w25q32", INFO(0xef4016, 0, 64 * 1024, 64, SECT_4K) }, - { "w25x64", INFO(0xef3017, 0, 64 * 1024, 128, SECT_4K) }, - { "w25q64", INFO(0xef4017, 0, 64 * 1024, 128, SECT_4K) }, - - /* Catalyst / On Semiconductor -- non-JEDEC */ - { "cat25c11", CAT25_INFO( 16, 8, 16, 1) }, - { "cat25c03", CAT25_INFO( 32, 8, 16, 2) }, - { "cat25c09", CAT25_INFO( 128, 8, 32, 2) }, - { "cat25c17", CAT25_INFO( 256, 8, 32, 2) }, - { "cat25128", CAT25_INFO(2048, 8, 64, 2) }, - { }, -}; -MODULE_DEVICE_TABLE(spi, m25p_ids); - -static const struct spi_device_id *__devinit jedec_probe(struct spi_device *spi) -{ - int tmp; - u8 code = OPCODE_RDID; - u8 id[5]; - u32 jedec; - u16 ext_jedec; - struct flash_info *info; - - /* JEDEC also defines an optional "extended device information" - * string for after vendor-specific data, after the three bytes - * we use here. Supporting some chips might require using it. - */ - tmp = spi_write_then_read(spi, &code, 1, id, 5); - if (tmp < 0) { - pr_debug("%s: error %d reading JEDEC ID\n", - dev_name(&spi->dev), tmp); - return ERR_PTR(tmp); - } - jedec = id[0]; - jedec = jedec << 8; - jedec |= id[1]; - jedec = jedec << 8; - jedec |= id[2]; + /* Set up command buffer. */ + flash->command[0] = nor->erase_opcode; + m25p_addr2cmd(nor, offset, flash->command); - ext_jedec = id[3] << 8 | id[4]; + spi_write(flash->spi, flash->command, m25p_cmdsz(nor)); - for (tmp = 0; tmp < ARRAY_SIZE(m25p_ids) - 1; tmp++) { - info = (void *)m25p_ids[tmp].driver_data; - if (info->jedec_id == jedec) { - if (info->ext_id != 0 && info->ext_id != ext_jedec) - continue; - return &m25p_ids[tmp]; - } - } - dev_err(&spi->dev, "unrecognized JEDEC id %06x\n", jedec); - return ERR_PTR(-ENODEV); + return 0; } - /* * board specific setup should have ensured the SPI clock used here * matches what the READ command supports, at least until this driver * understands FAST_READ (for clocks over 25 MHz). */ -static int __devinit m25p_probe(struct spi_device *spi) +static int m25p_probe(struct spi_device *spi) { - const struct spi_device_id *id = spi_get_device_id(spi); - struct flash_platform_data *data; - struct m25p *flash; - struct flash_info *info; - unsigned i; struct mtd_part_parser_data ppdata; + struct flash_platform_data *data; + struct m25p *flash; + struct spi_nor *nor; + enum read_mode mode = SPI_NOR_NORMAL; + int ret; -#ifdef CONFIG_MTD_OF_PARTS - if (!of_device_is_available(spi->dev.of_node)) - return -ENODEV; -#endif - - /* Platform data helps sort out which chip type we have, as - * well as how this board partitions it. If we don't have - * a chip ID, try the JEDEC id commands; they'll work for most - * newer chips, even if we don't recognize the particular chip. - */ - data = spi->dev.platform_data; - if (data && data->type) { - const struct spi_device_id *plat_id; - - for (i = 0; i < ARRAY_SIZE(m25p_ids) - 1; i++) { - plat_id = &m25p_ids[i]; - if (strcmp(data->type, plat_id->name)) - continue; - break; - } - - if (i < ARRAY_SIZE(m25p_ids) - 1) - id = plat_id; - else - dev_warn(&spi->dev, "unrecognized id %s\n", data->type); - } - - info = (void *)id->driver_data; - - if (info->jedec_id) { - const struct spi_device_id *jid; - - jid = jedec_probe(spi); - if (IS_ERR(jid)) { - return PTR_ERR(jid); - } else if (jid != id) { - /* - * JEDEC knows better, so overwrite platform ID. We - * can't trust partitions any longer, but we'll let - * mtd apply them anyway, since some partitions may be - * marked read-only, and we don't want to lose that - * information, even if it's not 100% accurate. - */ - dev_warn(&spi->dev, "found %s, expected %s\n", - jid->name, id->name); - id = jid; - info = (void *)jid->driver_data; - } - } - - flash = kzalloc(sizeof *flash, GFP_KERNEL); + flash = devm_kzalloc(&spi->dev, sizeof(*flash), GFP_KERNEL); if (!flash) return -ENOMEM; - flash->command = kmalloc(MAX_CMD_SIZE + FAST_READ_DUMMY_BYTE, GFP_KERNEL); - if (!flash->command) { - kfree(flash); - return -ENOMEM; - } - flash->spi = spi; - mutex_init(&flash->lock); - dev_set_drvdata(&spi->dev, flash); + nor = &flash->spi_nor; - /* - * Atmel, SST and Intel/Numonyx serial flash tend to power - * up with the software protection bits set - */ + /* install the hooks */ + nor->read = m25p80_read; + nor->write = m25p80_write; + nor->erase = m25p80_erase; + nor->write_reg = m25p80_write_reg; + nor->read_reg = m25p80_read_reg; - if (JEDEC_MFR(info->jedec_id) == CFI_MFR_ATMEL || - JEDEC_MFR(info->jedec_id) == CFI_MFR_INTEL || - JEDEC_MFR(info->jedec_id) == CFI_MFR_SST) { - write_enable(flash); - write_sr(flash, 0); - } - - if (data && data->name) - flash->mtd.name = data->name; - else - flash->mtd.name = dev_name(&spi->dev); - - flash->mtd.type = MTD_NORFLASH; - flash->mtd.writesize = 1; - flash->mtd.flags = MTD_CAP_NORFLASH; - flash->mtd.size = info->sector_size * info->n_sectors; - flash->mtd.erase = m25p80_erase; - flash->mtd.read = m25p80_read; - - /* sst flash chips use AAI word program */ - if (JEDEC_MFR(info->jedec_id) == CFI_MFR_SST) - flash->mtd.write = sst_write; - else - flash->mtd.write = m25p80_write; + nor->dev = &spi->dev; + nor->mtd = &flash->mtd; + nor->priv = flash; - /* prefer "small sector" erase if possible */ - if (info->flags & SECT_4K) { - flash->erase_opcode = OPCODE_BE_4K; - flash->mtd.erasesize = 4096; - } else { - flash->erase_opcode = OPCODE_SE; - flash->mtd.erasesize = info->sector_size; - } + spi_set_drvdata(spi, flash); + flash->mtd.priv = nor; + flash->spi = spi; - if (info->flags & M25P_NO_ERASE) - flash->mtd.flags |= MTD_NO_ERASE; + if (spi->mode & SPI_RX_QUAD) + mode = SPI_NOR_QUAD; + else if (spi->mode & SPI_RX_DUAL) + mode = SPI_NOR_DUAL; + ret = spi_nor_scan(nor, spi_get_device_id(spi), mode); + if (ret) + return ret; + data = dev_get_platdata(&spi->dev); ppdata.of_node = spi->dev.of_node; - flash->mtd.dev.parent = &spi->dev; - flash->page_size = info->page_size; - - if (info->addr_width) - flash->addr_width = info->addr_width; - else { - /* enable 4-byte addressing if the device exceeds 16MiB */ - if (flash->mtd.size > 0x1000000) { - flash->addr_width = 4; - set_4byte(flash, info->jedec_id, 1); - } else - flash->addr_width = 3; - } - - dev_info(&spi->dev, "%s (%lld Kbytes)\n", id->name, - (long long)flash->mtd.size >> 10); - - pr_debug("mtd .name = %s, .size = 0x%llx (%lldMiB) " - ".erasesize = 0x%.8x (%uKiB) .numeraseregions = %d\n", - flash->mtd.name, - (long long)flash->mtd.size, (long long)(flash->mtd.size >> 20), - flash->mtd.erasesize, flash->mtd.erasesize / 1024, - flash->mtd.numeraseregions); - - if (flash->mtd.numeraseregions) - for (i = 0; i < flash->mtd.numeraseregions; i++) - pr_debug("mtd.eraseregions[%d] = { .offset = 0x%llx, " - ".erasesize = 0x%.8x (%uKiB), " - ".numblocks = %d }\n", - i, (long long)flash->mtd.eraseregions[i].offset, - flash->mtd.eraseregions[i].erasesize, - flash->mtd.eraseregions[i].erasesize / 1024, - flash->mtd.eraseregions[i].numblocks); - - /* partitions should match sector boundaries; and it may be good to - * use readonly partitions for writeprotected sectors (BP2..BP0). - */ return mtd_device_parse_register(&flash->mtd, NULL, &ppdata, data ? data->parts : NULL, data ? data->nr_parts : 0); } -static int __devexit m25p_remove(struct spi_device *spi) +static int m25p_remove(struct spi_device *spi) { - struct m25p *flash = dev_get_drvdata(&spi->dev); - int status; + struct m25p *flash = spi_get_drvdata(spi); /* Clean up MTD stuff. */ - status = mtd_device_unregister(&flash->mtd); - if (status == 0) { - kfree(flash->command); - kfree(flash); - } - return 0; + return mtd_device_unregister(&flash->mtd); } @@ -994,9 +250,9 @@ static struct spi_driver m25p80_driver = { .name = "m25p80", .owner = THIS_MODULE, }, - .id_table = m25p_ids, + .id_table = spi_nor_ids, .probe = m25p_probe, - .remove = __devexit_p(m25p_remove), + .remove = m25p_remove, /* REVISIT: many of these chips have deep power-down modes, which * should clearly be entered on suspend() to minimize power use. @@ -1004,21 +260,7 @@ static struct spi_driver m25p80_driver = { */ }; - -static int __init m25p80_init(void) -{ - return spi_register_driver(&m25p80_driver); -} - - -static void __exit m25p80_exit(void) -{ - spi_unregister_driver(&m25p80_driver); -} - - -module_init(m25p80_init); -module_exit(m25p80_exit); +module_spi_driver(m25p80_driver); MODULE_LICENSE("GPL"); MODULE_AUTHOR("Mike Lavender"); diff --git a/drivers/mtd/devices/ms02-nv.c b/drivers/mtd/devices/ms02-nv.c index 8423fb6d4f2..5c8b322ba90 100644 --- a/drivers/mtd/devices/ms02-nv.c +++ b/drivers/mtd/devices/ms02-nv.c @@ -59,12 +59,8 @@ static int ms02nv_read(struct mtd_info *mtd, loff_t from, { struct ms02nv_private *mp = mtd->priv; - if (from + len > mtd->size) - return -EINVAL; - memcpy(buf, mp->uaddr + from, len); *retlen = len; - return 0; } @@ -73,12 +69,8 @@ static int ms02nv_write(struct mtd_info *mtd, loff_t to, { struct ms02nv_private *mp = mtd->priv; - if (to + len > mtd->size) - return -EINVAL; - memcpy(mp->uaddr + to, buf, len); *retlen = len; - return 0; } @@ -213,10 +205,10 @@ static int __init ms02nv_init_one(ulong addr) mtd->type = MTD_RAM; mtd->flags = MTD_CAP_RAM; mtd->size = fixsize; - mtd->name = (char *)ms02nv_name; + mtd->name = ms02nv_name; mtd->owner = THIS_MODULE; - mtd->read = ms02nv_read; - mtd->write = ms02nv_write; + mtd->_read = ms02nv_read; + mtd->_write = ms02nv_write; mtd->writesize = 1; ret = -EIO; diff --git a/drivers/mtd/devices/mtd_dataflash.c b/drivers/mtd/devices/mtd_dataflash.c index 236057ead0d..dd22ce2cc9a 100644 --- a/drivers/mtd/devices/mtd_dataflash.c +++ b/drivers/mtd/devices/mtd_dataflash.c @@ -10,7 +10,6 @@ * 2 of the License, or (at your option) any later version. */ #include <linux/module.h> -#include <linux/init.h> #include <linux/slab.h> #include <linux/delay.h> #include <linux/device.h> @@ -88,8 +87,6 @@ struct dataflash { uint8_t command[4]; char name[24]; - unsigned partitioned:1; - unsigned short page_offset; /* offset in flash address */ unsigned int page_size; /* of bytes per page */ @@ -105,8 +102,6 @@ static const struct of_device_id dataflash_dt_ids[] = { { .compatible = "atmel,dataflash", }, { /* sentinel */ } }; -#else -#define dataflash_dt_ids NULL #endif /* ......................................................................... */ @@ -164,9 +159,6 @@ static int dataflash_erase(struct mtd_info *mtd, struct erase_info *instr) dev_name(&spi->dev), (long long)instr->addr, (long long)instr->len); - /* Sanity checks */ - if (instr->addr + instr->len > mtd->size) - return -EINVAL; div_u64_rem(instr->len, priv->page_size, &rem); if (rem) return -EINVAL; @@ -252,14 +244,6 @@ static int dataflash_read(struct mtd_info *mtd, loff_t from, size_t len, pr_debug("%s: read 0x%x..0x%x\n", dev_name(&priv->spi->dev), (unsigned)from, (unsigned)(from + len)); - *retlen = 0; - - /* Sanity checks */ - if (!len) - return 0; - if (from + len > mtd->size) - return -EINVAL; - /* Calculate flash page/byte address */ addr = (((unsigned)from / priv->page_size) << priv->page_offset) + ((unsigned)from % priv->page_size); @@ -328,14 +312,6 @@ static int dataflash_write(struct mtd_info *mtd, loff_t to, size_t len, pr_debug("%s: write 0x%x..0x%x\n", dev_name(&spi->dev), (unsigned)to, (unsigned)(to + len)); - *retlen = 0; - - /* Sanity checks */ - if (!len) - return 0; - if ((to + len) > mtd->size) - return -EINVAL; - spi_message_init(&msg); x[0].tx_buf = command = priv->command; @@ -463,8 +439,8 @@ static int dataflash_write(struct mtd_info *mtd, loff_t to, size_t len, #ifdef CONFIG_MTD_DATAFLASH_OTP -static int dataflash_get_otp_info(struct mtd_info *mtd, - struct otp_info *info, size_t len) +static int dataflash_get_otp_info(struct mtd_info *mtd, size_t len, + size_t *retlen, struct otp_info *info) { /* Report both blocks as identical: bytes 0..64, locked. * Unless the user block changed from all-ones, we can't @@ -473,7 +449,8 @@ static int dataflash_get_otp_info(struct mtd_info *mtd, info->start = 0; info->length = 64; info->locked = 1; - return sizeof(*info); + *retlen = sizeof(*info); + return 0; } static ssize_t otp_read(struct spi_device *spi, unsigned base, @@ -490,8 +467,6 @@ static ssize_t otp_read(struct spi_device *spi, unsigned base, if ((off + len) > 64) len = 64 - off; - if (len == 0) - return len; spi_message_init(&m); @@ -567,14 +542,18 @@ static int dataflash_write_user_otp(struct mtd_info *mtd, struct dataflash *priv = mtd->priv; int status; - if (len > 64) - return -EINVAL; + if (from >= 64) { + /* + * Attempting to write beyond the end of OTP memory, + * no data can be written. + */ + *retlen = 0; + return 0; + } - /* Strictly speaking, we *could* truncate the write ... but - * let's not do that for the only write that's ever possible. - */ + /* Truncate the write to fit into OTP memory. */ if ((from + len) > 64) - return -EINVAL; + len = 64 - from; /* OUT: OP_WRITE_SECURITY, 3 zeroes, 64 data-or-zero bytes * IN: ignore all @@ -611,16 +590,16 @@ static int dataflash_write_user_otp(struct mtd_info *mtd, static char *otp_setup(struct mtd_info *device, char revision) { - device->get_fact_prot_info = dataflash_get_otp_info; - device->read_fact_prot_reg = dataflash_read_fact_otp; - device->get_user_prot_info = dataflash_get_otp_info; - device->read_user_prot_reg = dataflash_read_user_otp; + device->_get_fact_prot_info = dataflash_get_otp_info; + device->_read_fact_prot_reg = dataflash_read_fact_otp; + device->_get_user_prot_info = dataflash_get_otp_info; + device->_read_user_prot_reg = dataflash_read_user_otp; /* rev c parts (at45db321c and at45db1281 only!) use a * different write procedure; not (yet?) implemented. */ if (revision > 'c') - device->write_user_prot_reg = dataflash_write_user_otp; + device->_write_user_prot_reg = dataflash_write_user_otp; return ", OTP"; } @@ -639,14 +618,13 @@ static char *otp_setup(struct mtd_info *device, char revision) /* * Register DataFlash device with MTD subsystem. */ -static int __devinit -add_dataflash_otp(struct spi_device *spi, char *name, - int nr_pages, int pagesize, int pageoffset, char revision) +static int add_dataflash_otp(struct spi_device *spi, char *name, int nr_pages, + int pagesize, int pageoffset, char revision) { struct dataflash *priv; struct mtd_info *device; struct mtd_part_parser_data ppdata; - struct flash_platform_data *pdata = spi->dev.platform_data; + struct flash_platform_data *pdata = dev_get_platdata(&spi->dev); char *otp_tag = ""; int err = 0; @@ -672,9 +650,9 @@ add_dataflash_otp(struct spi_device *spi, char *name, device->owner = THIS_MODULE; device->type = MTD_DATAFLASH; device->flags = MTD_WRITEABLE; - device->erase = dataflash_erase; - device->read = dataflash_read; - device->write = dataflash_write; + device->_erase = dataflash_erase; + device->_read = dataflash_read; + device->_write = dataflash_write; device->priv = priv; device->dev.parent = &spi->dev; @@ -685,7 +663,7 @@ add_dataflash_otp(struct spi_device *spi, char *name, dev_info(&spi->dev, "%s (%lld KBytes) pagesize %d bytes%s\n", name, (long long)((device->size + 1023) >> 10), pagesize, otp_tag); - dev_set_drvdata(&spi->dev, priv); + spi_set_drvdata(spi, priv); ppdata.of_node = spi->dev.of_node; err = mtd_device_parse_register(device, NULL, &ppdata, @@ -695,14 +673,12 @@ add_dataflash_otp(struct spi_device *spi, char *name, if (!err) return 0; - dev_set_drvdata(&spi->dev, NULL); kfree(priv); return err; } -static inline int __devinit -add_dataflash(struct spi_device *spi, char *name, - int nr_pages, int pagesize, int pageoffset) +static inline int add_dataflash(struct spi_device *spi, char *name, + int nr_pages, int pagesize, int pageoffset) { return add_dataflash_otp(spi, name, nr_pages, pagesize, pageoffset, 0); @@ -726,7 +702,7 @@ struct flash_info { #define IS_POW2PS 0x0001 /* uses 2^N byte pages */ }; -static struct flash_info __devinitdata dataflash_data [] = { +static struct flash_info dataflash_data[] = { /* * NOTE: chips with SUP_POW2PS (rev D and up) need two entries, @@ -761,7 +737,7 @@ static struct flash_info __devinitdata dataflash_data [] = { { "at45db642d", 0x1f2800, 8192, 1024, 10, SUP_POW2PS | IS_POW2PS}, }; -static struct flash_info *__devinit jedec_probe(struct spi_device *spi) +static struct flash_info *jedec_probe(struct spi_device *spi) { int tmp; uint8_t code = OP_READ_ID; @@ -844,7 +820,7 @@ static struct flash_info *__devinit jedec_probe(struct spi_device *spi) * AT45DB0642 64Mbit (8M) xx111xxx (0x3c) 8192 1056 11 * AT45DB1282 128Mbit (16M) xx0100xx (0x10) 16384 1056 11 */ -static int __devinit dataflash_probe(struct spi_device *spi) +static int dataflash_probe(struct spi_device *spi) { int status; struct flash_info *info; @@ -906,7 +882,7 @@ static int __devinit dataflash_probe(struct spi_device *spi) break; /* obsolete AT45DB1282 not (yet?) supported */ default: - pr_debug("%s: unsupported device (%x)\n", dev_name(&spi->dev), + dev_info(&spi->dev, "unsupported device (%x)\n", status & 0x3c); status = -ENODEV; } @@ -918,18 +894,16 @@ static int __devinit dataflash_probe(struct spi_device *spi) return status; } -static int __devexit dataflash_remove(struct spi_device *spi) +static int dataflash_remove(struct spi_device *spi) { - struct dataflash *flash = dev_get_drvdata(&spi->dev); + struct dataflash *flash = spi_get_drvdata(spi); int status; pr_debug("%s: remove\n", dev_name(&spi->dev)); status = mtd_device_unregister(&flash->mtd); - if (status == 0) { - dev_set_drvdata(&spi->dev, NULL); + if (status == 0) kfree(flash); - } return status; } @@ -937,27 +911,16 @@ static struct spi_driver dataflash_driver = { .driver = { .name = "mtd_dataflash", .owner = THIS_MODULE, - .of_match_table = dataflash_dt_ids, + .of_match_table = of_match_ptr(dataflash_dt_ids), }, .probe = dataflash_probe, - .remove = __devexit_p(dataflash_remove), + .remove = dataflash_remove, /* FIXME: investigate suspend and resume... */ }; -static int __init dataflash_init(void) -{ - return spi_register_driver(&dataflash_driver); -} -module_init(dataflash_init); - -static void __exit dataflash_exit(void) -{ - spi_unregister_driver(&dataflash_driver); -} -module_exit(dataflash_exit); - +module_spi_driver(dataflash_driver); MODULE_LICENSE("GPL"); MODULE_AUTHOR("Andrew Victor, David Brownell"); diff --git a/drivers/mtd/devices/mtdram.c b/drivers/mtd/devices/mtdram.c index 2562689ba6b..8e285089229 100644 --- a/drivers/mtd/devices/mtdram.c +++ b/drivers/mtd/devices/mtdram.c @@ -34,34 +34,23 @@ static struct mtd_info *mtd_info; static int ram_erase(struct mtd_info *mtd, struct erase_info *instr) { - if (instr->addr + instr->len > mtd->size) - return -EINVAL; - memset((char *)mtd->priv + instr->addr, 0xff, instr->len); - instr->state = MTD_ERASE_DONE; mtd_erase_callback(instr); - return 0; } static int ram_point(struct mtd_info *mtd, loff_t from, size_t len, size_t *retlen, void **virt, resource_size_t *phys) { - if (from + len > mtd->size) - return -EINVAL; - - /* can we return a physical address with this driver? */ - if (phys) - return -EINVAL; - *virt = mtd->priv + from; *retlen = len; return 0; } -static void ram_unpoint(struct mtd_info *mtd, loff_t from, size_t len) +static int ram_unpoint(struct mtd_info *mtd, loff_t from, size_t len) { + return 0; } /* @@ -80,11 +69,7 @@ static unsigned long ram_get_unmapped_area(struct mtd_info *mtd, static int ram_read(struct mtd_info *mtd, loff_t from, size_t len, size_t *retlen, u_char *buf) { - if (from + len > mtd->size) - return -EINVAL; - memcpy(buf, mtd->priv + from, len); - *retlen = len; return 0; } @@ -92,11 +77,7 @@ static int ram_read(struct mtd_info *mtd, loff_t from, size_t len, static int ram_write(struct mtd_info *mtd, loff_t to, size_t len, size_t *retlen, const u_char *buf) { - if (to + len > mtd->size) - return -EINVAL; - memcpy((char *)mtd->priv + to, buf, len); - *retlen = len; return 0; } @@ -111,7 +92,7 @@ static void __exit cleanup_mtdram(void) } int mtdram_init_device(struct mtd_info *mtd, void *mapped_address, - unsigned long size, char *name) + unsigned long size, const char *name) { memset(mtd, 0, sizeof(*mtd)); @@ -126,12 +107,12 @@ int mtdram_init_device(struct mtd_info *mtd, void *mapped_address, mtd->priv = mapped_address; mtd->owner = THIS_MODULE; - mtd->erase = ram_erase; - mtd->point = ram_point; - mtd->unpoint = ram_unpoint; - mtd->get_unmapped_area = ram_get_unmapped_area; - mtd->read = ram_read; - mtd->write = ram_write; + mtd->_erase = ram_erase; + mtd->_point = ram_point; + mtd->_unpoint = ram_unpoint; + mtd->_get_unmapped_area = ram_get_unmapped_area; + mtd->_read = ram_read; + mtd->_write = ram_write; if (mtd_device_register(mtd, NULL, 0)) return -EIO; diff --git a/drivers/mtd/devices/phram.c b/drivers/mtd/devices/phram.c index 23423bd00b0..2cceebfb251 100644 --- a/drivers/mtd/devices/phram.c +++ b/drivers/mtd/devices/phram.c @@ -33,45 +33,33 @@ struct phram_mtd_list { static LIST_HEAD(phram_list); - static int phram_erase(struct mtd_info *mtd, struct erase_info *instr) { u_char *start = mtd->priv; - if (instr->addr + instr->len > mtd->size) - return -EINVAL; - memset(start + instr->addr, 0xff, instr->len); - /* This'll catch a few races. Free the thing before returning :) + /* + * This'll catch a few races. Free the thing before returning :) * I don't feel at all ashamed. This kind of thing is possible anyway * with flash, but unlikely. */ - instr->state = MTD_ERASE_DONE; - mtd_erase_callback(instr); - return 0; } static int phram_point(struct mtd_info *mtd, loff_t from, size_t len, size_t *retlen, void **virt, resource_size_t *phys) { - if (from + len > mtd->size) - return -EINVAL; - - /* can we return a physical address with this driver? */ - if (phys) - return -EINVAL; - *virt = mtd->priv + from; *retlen = len; return 0; } -static void phram_unpoint(struct mtd_info *mtd, loff_t from, size_t len) +static int phram_unpoint(struct mtd_info *mtd, loff_t from, size_t len) { + return 0; } static int phram_read(struct mtd_info *mtd, loff_t from, size_t len, @@ -79,14 +67,7 @@ static int phram_read(struct mtd_info *mtd, loff_t from, size_t len, { u_char *start = mtd->priv; - if (from >= mtd->size) - return -EINVAL; - - if (len > mtd->size - from) - len = mtd->size - from; - memcpy(buf, start + from, len); - *retlen = len; return 0; } @@ -96,20 +77,11 @@ static int phram_write(struct mtd_info *mtd, loff_t to, size_t len, { u_char *start = mtd->priv; - if (to >= mtd->size) - return -EINVAL; - - if (len > mtd->size - to) - len = mtd->size - to; - memcpy(start + to, buf, len); - *retlen = len; return 0; } - - static void unregister_devices(void) { struct phram_mtd_list *this, *safe; @@ -122,7 +94,7 @@ static void unregister_devices(void) } } -static int register_device(char *name, unsigned long start, unsigned long len) +static int register_device(char *name, phys_addr_t start, size_t len) { struct phram_mtd_list *new; int ret = -ENOMEM; @@ -142,11 +114,11 @@ static int register_device(char *name, unsigned long start, unsigned long len) new->mtd.name = name; new->mtd.size = len; new->mtd.flags = MTD_CAP_RAM; - new->mtd.erase = phram_erase; - new->mtd.point = phram_point; - new->mtd.unpoint = phram_unpoint; - new->mtd.read = phram_read; - new->mtd.write = phram_write; + new->mtd._erase = phram_erase; + new->mtd._point = phram_point; + new->mtd._unpoint = phram_unpoint; + new->mtd._read = phram_read; + new->mtd._write = phram_write; new->mtd.owner = THIS_MODULE; new->mtd.type = MTD_RAM; new->mtd.erasesize = PAGE_SIZE; @@ -169,35 +141,35 @@ out0: return ret; } -static int ustrtoul(const char *cp, char **endp, unsigned int base) +static int parse_num64(uint64_t *num64, char *token) { - unsigned long result = simple_strtoul(cp, endp, base); - - switch (**endp) { - case 'G': - result *= 1024; - case 'M': - result *= 1024; - case 'k': - result *= 1024; + size_t len; + int shift = 0; + int ret; + + len = strlen(token); /* By dwmw2 editorial decree, "ki", "Mi" or "Gi" are to be used. */ - if ((*endp)[1] == 'i') - (*endp) += 2; + if (len > 2) { + if (token[len - 1] == 'i') { + switch (token[len - 2]) { + case 'G': + shift += 10; + case 'M': + shift += 10; + case 'k': + shift += 10; + token[len - 2] = 0; + break; + default: + return -EINVAL; + } + } } - return result; -} - -static int parse_num32(uint32_t *num32, const char *token) -{ - char *endp; - unsigned long n; - n = ustrtoul(token, &endp, 0); - if (*endp) - return -EINVAL; + ret = kstrtou64(token, 0, num64); + *num64 <<= shift; - *num32 = n; - return 0; + return ret; } static int parse_name(char **pname, const char *token) @@ -233,13 +205,26 @@ static inline void kill_final_newline(char *str) return 1; \ } while (0) -static int phram_setup(const char *val, struct kernel_param *kp) +#ifndef MODULE +static int phram_init_called; +/* + * This shall contain the module parameter if any. It is of the form: + * - phram=<device>,<address>,<size> for module case + * - phram.phram=<device>,<address>,<size> for built-in case + * We leave 64 bytes for the device name, 20 for the address and 20 for the + * size. + * Example: phram.phram=rootfs,0xa0000000,512Mi + */ +static char phram_paramline[64 + 20 + 20]; +#endif + +static int phram_setup(const char *val) { - char buf[64+12+12], *str = buf; + char buf[64 + 20 + 20], *str = buf; char *token[3]; char *name; - uint32_t start; - uint32_t len; + uint64_t start; + uint64_t len; int i, ret; if (strnlen(val, sizeof(buf)) >= sizeof(buf)) @@ -261,13 +246,13 @@ static int phram_setup(const char *val, struct kernel_param *kp) if (ret) return ret; - ret = parse_num32(&start, token[1]); + ret = parse_num64(&start, token[1]); if (ret) { kfree(name); parse_err("illegal start address\n"); } - ret = parse_num32(&len, token[2]); + ret = parse_num64(&len, token[2]); if (ret) { kfree(name); parse_err("illegal device length\n"); @@ -275,20 +260,60 @@ static int phram_setup(const char *val, struct kernel_param *kp) ret = register_device(name, start, len); if (!ret) - pr_info("%s device: %#x at %#x\n", name, len, start); + pr_info("%s device: %#llx at %#llx\n", name, len, start); else kfree(name); return ret; } -module_param_call(phram, phram_setup, NULL, NULL, 000); +static int phram_param_call(const char *val, struct kernel_param *kp) +{ +#ifdef MODULE + return phram_setup(val); +#else + /* + * If more parameters are later passed in via + * /sys/module/phram/parameters/phram + * and init_phram() has already been called, + * we can parse the argument now. + */ + + if (phram_init_called) + return phram_setup(val); + + /* + * During early boot stage, we only save the parameters + * here. We must parse them later: if the param passed + * from kernel boot command line, phram_param_call() is + * called so early that it is not possible to resolve + * the device (even kmalloc() fails). Defer that work to + * phram_setup(). + */ + + if (strlen(val) >= sizeof(phram_paramline)) + return -ENOSPC; + strcpy(phram_paramline, val); + + return 0; +#endif +} + +module_param_call(phram, phram_param_call, NULL, NULL, 000); MODULE_PARM_DESC(phram, "Memory region to map. \"phram=<name>,<start>,<length>\""); static int __init init_phram(void) { - return 0; + int ret = 0; + +#ifndef MODULE + if (phram_paramline[0]) + ret = phram_setup(phram_paramline); + phram_init_called = 1; +#endif + + return ret; } static void __exit cleanup_phram(void) diff --git a/drivers/mtd/devices/pmc551.c b/drivers/mtd/devices/pmc551.c index ecff765579d..f02603e1bfe 100644 --- a/drivers/mtd/devices/pmc551.c +++ b/drivers/mtd/devices/pmc551.c @@ -93,14 +93,49 @@ #include <linux/fs.h> #include <linux/ioctl.h> #include <asm/io.h> -#include <asm/system.h> #include <linux/pci.h> - #include <linux/mtd/mtd.h> -#include <linux/mtd/pmc551.h> + +#define PMC551_VERSION \ + "Ramix PMC551 PCI Mezzanine Ram Driver. (C) 1999,2000 Nortel Networks.\n" + +#define PCI_VENDOR_ID_V3_SEMI 0x11b0 +#define PCI_DEVICE_ID_V3_SEMI_V370PDC 0x0200 + +#define PMC551_PCI_MEM_MAP0 0x50 +#define PMC551_PCI_MEM_MAP1 0x54 +#define PMC551_PCI_MEM_MAP_MAP_ADDR_MASK 0x3ff00000 +#define PMC551_PCI_MEM_MAP_APERTURE_MASK 0x000000f0 +#define PMC551_PCI_MEM_MAP_REG_EN 0x00000002 +#define PMC551_PCI_MEM_MAP_ENABLE 0x00000001 + +#define PMC551_SDRAM_MA 0x60 +#define PMC551_SDRAM_CMD 0x62 +#define PMC551_DRAM_CFG 0x64 +#define PMC551_SYS_CTRL_REG 0x78 + +#define PMC551_DRAM_BLK0 0x68 +#define PMC551_DRAM_BLK1 0x6c +#define PMC551_DRAM_BLK2 0x70 +#define PMC551_DRAM_BLK3 0x74 +#define PMC551_DRAM_BLK_GET_SIZE(x) (524288 << ((x >> 4) & 0x0f)) +#define PMC551_DRAM_BLK_SET_COL_MUX(x, v) (((x) & ~0x00007000) | (((v) & 0x7) << 12)) +#define PMC551_DRAM_BLK_SET_ROW_MUX(x, v) (((x) & ~0x00000f00) | (((v) & 0xf) << 8)) + +struct mypriv { + struct pci_dev *dev; + u_char *start; + u32 base_map0; + u32 curr_map0; + u32 asize; + struct mtd_info *nextpmc551; +}; static struct mtd_info *pmc551list; +static int pmc551_point(struct mtd_info *mtd, loff_t from, size_t len, + size_t *retlen, void **virt, resource_size_t *phys); + static int pmc551_erase(struct mtd_info *mtd, struct erase_info *instr) { struct mypriv *priv = mtd->priv; @@ -116,16 +151,6 @@ static int pmc551_erase(struct mtd_info *mtd, struct erase_info *instr) #endif end = instr->addr + instr->len - 1; - - /* Is it past the end? */ - if (end > mtd->size) { -#ifdef CONFIG_MTD_PMC551_DEBUG - printk(KERN_DEBUG "pmc551_erase() out of bounds (%ld > %ld)\n", - (long)end, (long)mtd->size); -#endif - return -EINVAL; - } - eoff_hi = end & ~(priv->asize - 1); soff_hi = instr->addr & ~(priv->asize - 1); eoff_lo = end & (priv->asize - 1); @@ -179,18 +204,6 @@ static int pmc551_point(struct mtd_info *mtd, loff_t from, size_t len, printk(KERN_DEBUG "pmc551_point(%ld, %ld)\n", (long)from, (long)len); #endif - if (from + len > mtd->size) { -#ifdef CONFIG_MTD_PMC551_DEBUG - printk(KERN_DEBUG "pmc551_point() out of bounds (%ld > %ld)\n", - (long)from + len, (long)mtd->size); -#endif - return -EINVAL; - } - - /* can we return a physical address with this driver? */ - if (phys) - return -EINVAL; - soff_hi = from & ~(priv->asize - 1); soff_lo = from & (priv->asize - 1); @@ -206,11 +219,12 @@ static int pmc551_point(struct mtd_info *mtd, loff_t from, size_t len, return 0; } -static void pmc551_unpoint(struct mtd_info *mtd, loff_t from, size_t len) +static int pmc551_unpoint(struct mtd_info *mtd, loff_t from, size_t len) { #ifdef CONFIG_MTD_PMC551_DEBUG printk(KERN_DEBUG "pmc551_unpoint()\n"); #endif + return 0; } static int pmc551_read(struct mtd_info *mtd, loff_t from, size_t len, @@ -229,16 +243,6 @@ static int pmc551_read(struct mtd_info *mtd, loff_t from, size_t len, #endif end = from + len - 1; - - /* Is it past the end? */ - if (end > mtd->size) { -#ifdef CONFIG_MTD_PMC551_DEBUG - printk(KERN_DEBUG "pmc551_read() out of bounds (%ld > %ld)\n", - (long)end, (long)mtd->size); -#endif - return -EINVAL; - } - soff_hi = from & ~(priv->asize - 1); eoff_hi = end & ~(priv->asize - 1); soff_lo = from & (priv->asize - 1); @@ -296,16 +300,6 @@ static int pmc551_write(struct mtd_info *mtd, loff_t to, size_t len, #endif end = to + len - 1; - /* Is it past the end? or did the u32 wrap? */ - if (end > mtd->size) { -#ifdef CONFIG_MTD_PMC551_DEBUG - printk(KERN_DEBUG "pmc551_write() out of bounds (end: %ld, " - "size: %ld, to: %ld)\n", (long)end, (long)mtd->size, - (long)to); -#endif - return -EINVAL; - } - soff_hi = to & ~(priv->asize - 1); eoff_hi = end & ~(priv->asize - 1); soff_lo = to & (priv->asize - 1); @@ -359,7 +353,7 @@ static int pmc551_write(struct mtd_info *mtd, loff_t to, size_t len, * mechanism * returns the size of the memory region found. */ -static u32 fixup_pmc551(struct pci_dev *dev) +static int fixup_pmc551(struct pci_dev *dev) { #ifdef CONFIG_MTD_PMC551_BUGFIX u32 dram_data; @@ -669,7 +663,7 @@ static int __init init_pmc551(void) struct mypriv *priv; int found = 0; struct mtd_info *mtd; - u32 length = 0; + int length = 0; if (msize) { msize = (1 << (ffs(msize) - 1)) << 20; @@ -731,16 +725,11 @@ static int __init init_pmc551(void) } mtd = kzalloc(sizeof(struct mtd_info), GFP_KERNEL); - if (!mtd) { - printk(KERN_NOTICE "pmc551: Cannot allocate new MTD " - "device.\n"); + if (!mtd) break; - } priv = kzalloc(sizeof(struct mypriv), GFP_KERNEL); if (!priv) { - printk(KERN_NOTICE "pmc551: Cannot allocate new MTD " - "device.\n"); kfree(mtd); break; } @@ -787,11 +776,11 @@ static int __init init_pmc551(void) mtd->size = msize; mtd->flags = MTD_CAP_RAM; - mtd->erase = pmc551_erase; - mtd->read = pmc551_read; - mtd->write = pmc551_write; - mtd->point = pmc551_point; - mtd->unpoint = pmc551_unpoint; + mtd->_erase = pmc551_erase; + mtd->_read = pmc551_read; + mtd->_write = pmc551_write; + mtd->_point = pmc551_point; + mtd->_unpoint = pmc551_unpoint; mtd->type = MTD_RAM; mtd->name = "PMC551 RAM board"; mtd->erasesize = 0x10000; diff --git a/drivers/mtd/devices/serial_flash_cmds.h b/drivers/mtd/devices/serial_flash_cmds.h new file mode 100644 index 00000000000..f59a125295d --- /dev/null +++ b/drivers/mtd/devices/serial_flash_cmds.h @@ -0,0 +1,61 @@ +/* + * Generic/SFDP Flash Commands and Device Capabilities + * + * Copyright (C) 2013 Lee Jones <lee.jones@lianro.org> + * + * This code is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#ifndef _MTD_SERIAL_FLASH_CMDS_H +#define _MTD_SERIAL_FLASH_CMDS_H + +/* Generic Flash Commands/OPCODEs */ +#define SPINOR_OP_RDSR2 0x35 +#define SPINOR_OP_WRVCR 0x81 +#define SPINOR_OP_RDVCR 0x85 + +/* JEDEC Standard - Serial Flash Discoverable Parmeters (SFDP) Commands */ +#define SPINOR_OP_READ_1_2_2 0xbb /* DUAL I/O READ */ +#define SPINOR_OP_READ_1_4_4 0xeb /* QUAD I/O READ */ + +#define SPINOR_OP_WRITE 0x02 /* PAGE PROGRAM */ +#define SPINOR_OP_WRITE_1_1_2 0xa2 /* DUAL INPUT PROGRAM */ +#define SPINOR_OP_WRITE_1_2_2 0xd2 /* DUAL INPUT EXT PROGRAM */ +#define SPINOR_OP_WRITE_1_1_4 0x32 /* QUAD INPUT PROGRAM */ +#define SPINOR_OP_WRITE_1_4_4 0x12 /* QUAD INPUT EXT PROGRAM */ + +/* READ commands with 32-bit addressing */ +#define SPINOR_OP_READ4_1_2_2 0xbc +#define SPINOR_OP_READ4_1_4_4 0xec + +/* Configuration flags */ +#define FLASH_FLAG_SINGLE 0x000000ff +#define FLASH_FLAG_READ_WRITE 0x00000001 +#define FLASH_FLAG_READ_FAST 0x00000002 +#define FLASH_FLAG_SE_4K 0x00000004 +#define FLASH_FLAG_SE_32K 0x00000008 +#define FLASH_FLAG_CE 0x00000010 +#define FLASH_FLAG_32BIT_ADDR 0x00000020 +#define FLASH_FLAG_RESET 0x00000040 +#define FLASH_FLAG_DYB_LOCKING 0x00000080 + +#define FLASH_FLAG_DUAL 0x0000ff00 +#define FLASH_FLAG_READ_1_1_2 0x00000100 +#define FLASH_FLAG_READ_1_2_2 0x00000200 +#define FLASH_FLAG_READ_2_2_2 0x00000400 +#define FLASH_FLAG_WRITE_1_1_2 0x00001000 +#define FLASH_FLAG_WRITE_1_2_2 0x00002000 +#define FLASH_FLAG_WRITE_2_2_2 0x00004000 + +#define FLASH_FLAG_QUAD 0x00ff0000 +#define FLASH_FLAG_READ_1_1_4 0x00010000 +#define FLASH_FLAG_READ_1_4_4 0x00020000 +#define FLASH_FLAG_READ_4_4_4 0x00040000 +#define FLASH_FLAG_WRITE_1_1_4 0x00100000 +#define FLASH_FLAG_WRITE_1_4_4 0x00200000 +#define FLASH_FLAG_WRITE_4_4_4 0x00400000 + +#endif /* _MTD_SERIAL_FLASH_CMDS_H */ diff --git a/drivers/mtd/devices/slram.c b/drivers/mtd/devices/slram.c index e585263161b..2fc4957cbe7 100644 --- a/drivers/mtd/devices/slram.c +++ b/drivers/mtd/devices/slram.c @@ -42,7 +42,6 @@ #include <linux/ioctl.h> #include <linux/init.h> #include <asm/io.h> -#include <asm/system.h> #include <linux/mtd/mtd.h> @@ -76,7 +75,7 @@ static slram_mtd_list_t *slram_mtdlist = NULL; static int slram_erase(struct mtd_info *, struct erase_info *); static int slram_point(struct mtd_info *, loff_t, size_t, size_t *, void **, resource_size_t *); -static void slram_unpoint(struct mtd_info *, loff_t, size_t); +static int slram_unpoint(struct mtd_info *, loff_t, size_t); static int slram_read(struct mtd_info *, loff_t, size_t, size_t *, u_char *); static int slram_write(struct mtd_info *, loff_t, size_t, size_t *, const u_char *); @@ -84,21 +83,13 @@ static int slram_erase(struct mtd_info *mtd, struct erase_info *instr) { slram_priv_t *priv = mtd->priv; - if (instr->addr + instr->len > mtd->size) { - return(-EINVAL); - } - memset(priv->start + instr->addr, 0xff, instr->len); - /* This'll catch a few races. Free the thing before returning :) * I don't feel at all ashamed. This kind of thing is possible anyway * with flash, but unlikely. */ - instr->state = MTD_ERASE_DONE; - mtd_erase_callback(instr); - return(0); } @@ -107,20 +98,14 @@ static int slram_point(struct mtd_info *mtd, loff_t from, size_t len, { slram_priv_t *priv = mtd->priv; - /* can we return a physical address with this driver? */ - if (phys) - return -EINVAL; - - if (from + len > mtd->size) - return -EINVAL; - *virt = priv->start + from; *retlen = len; return(0); } -static void slram_unpoint(struct mtd_info *mtd, loff_t from, size_t len) +static int slram_unpoint(struct mtd_info *mtd, loff_t from, size_t len) { + return 0; } static int slram_read(struct mtd_info *mtd, loff_t from, size_t len, @@ -128,14 +113,7 @@ static int slram_read(struct mtd_info *mtd, loff_t from, size_t len, { slram_priv_t *priv = mtd->priv; - if (from > mtd->size) - return -EINVAL; - - if (from + len > mtd->size) - len = mtd->size - from; - memcpy(buf, priv->start + from, len); - *retlen = len; return(0); } @@ -145,11 +123,7 @@ static int slram_write(struct mtd_info *mtd, loff_t to, size_t len, { slram_priv_t *priv = mtd->priv; - if (to + len > mtd->size) - return -EINVAL; - memcpy(priv->start + to, buf, len); - *retlen = len; return(0); } @@ -200,11 +174,11 @@ static int register_device(char *name, unsigned long start, unsigned long length (*curmtd)->mtdinfo->name = name; (*curmtd)->mtdinfo->size = length; (*curmtd)->mtdinfo->flags = MTD_CAP_RAM; - (*curmtd)->mtdinfo->erase = slram_erase; - (*curmtd)->mtdinfo->point = slram_point; - (*curmtd)->mtdinfo->unpoint = slram_unpoint; - (*curmtd)->mtdinfo->read = slram_read; - (*curmtd)->mtdinfo->write = slram_write; + (*curmtd)->mtdinfo->_erase = slram_erase; + (*curmtd)->mtdinfo->_point = slram_point; + (*curmtd)->mtdinfo->_unpoint = slram_unpoint; + (*curmtd)->mtdinfo->_read = slram_read; + (*curmtd)->mtdinfo->_write = slram_write; (*curmtd)->mtdinfo->owner = THIS_MODULE; (*curmtd)->mtdinfo->type = MTD_RAM; (*curmtd)->mtdinfo->erasesize = SLRAM_BLK_SZ; @@ -266,7 +240,7 @@ static int parse_cmdline(char *devname, char *szstart, char *szlength) if (*(szlength) != '+') { devlength = simple_strtoul(szlength, &buffer, 0); - devlength = handle_unit(devlength, buffer) - devstart; + devlength = handle_unit(devlength, buffer); if (devlength < devstart) goto err_out; @@ -306,14 +280,11 @@ __setup("slram=", mtd_slram_setup); static int __init init_slram(void) { char *devname; - int i; #ifndef MODULE char *devstart; char *devlength; - i = 0; - if (!map) { E("slram: not enough parameters.\n"); return(-EINVAL); @@ -340,6 +311,7 @@ static int __init init_slram(void) } #else int count; + int i; for (count = 0; count < SLRAM_MAX_DEVICES_PARAMS && map[count]; count++) { diff --git a/drivers/mtd/devices/spear_smi.c b/drivers/mtd/devices/spear_smi.c new file mode 100644 index 00000000000..c4176b0f382 --- /dev/null +++ b/drivers/mtd/devices/spear_smi.c @@ -0,0 +1,1093 @@ +/* + * SMI (Serial Memory Controller) device driver for Serial NOR Flash on + * SPEAr platform + * The serial nor interface is largely based on drivers/mtd/m25p80.c, + * however the SPI interface has been replaced by SMI. + * + * Copyright © 2010 STMicroelectronics. + * Ashish Priyadarshi + * Shiraz Hashim <shiraz.linux.kernel@gmail.com> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/clk.h> +#include <linux/delay.h> +#include <linux/device.h> +#include <linux/err.h> +#include <linux/errno.h> +#include <linux/interrupt.h> +#include <linux/io.h> +#include <linux/ioport.h> +#include <linux/jiffies.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/param.h> +#include <linux/platform_device.h> +#include <linux/pm.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/partitions.h> +#include <linux/mtd/spear_smi.h> +#include <linux/mutex.h> +#include <linux/sched.h> +#include <linux/slab.h> +#include <linux/wait.h> +#include <linux/of.h> +#include <linux/of_address.h> + +/* SMI clock rate */ +#define SMI_MAX_CLOCK_FREQ 50000000 /* 50 MHz */ + +/* MAX time out to safely come out of a erase or write busy conditions */ +#define SMI_PROBE_TIMEOUT (HZ / 10) +#define SMI_MAX_TIME_OUT (3 * HZ) + +/* timeout for command completion */ +#define SMI_CMD_TIMEOUT (HZ / 10) + +/* registers of smi */ +#define SMI_CR1 0x0 /* SMI control register 1 */ +#define SMI_CR2 0x4 /* SMI control register 2 */ +#define SMI_SR 0x8 /* SMI status register */ +#define SMI_TR 0xC /* SMI transmit register */ +#define SMI_RR 0x10 /* SMI receive register */ + +/* defines for control_reg 1 */ +#define BANK_EN (0xF << 0) /* enables all banks */ +#define DSEL_TIME (0x6 << 4) /* Deselect time 6 + 1 SMI_CK periods */ +#define SW_MODE (0x1 << 28) /* enables SW Mode */ +#define WB_MODE (0x1 << 29) /* Write Burst Mode */ +#define FAST_MODE (0x1 << 15) /* Fast Mode */ +#define HOLD1 (0x1 << 16) /* Clock Hold period selection */ + +/* defines for control_reg 2 */ +#define SEND (0x1 << 7) /* Send data */ +#define TFIE (0x1 << 8) /* Transmission Flag Interrupt Enable */ +#define WCIE (0x1 << 9) /* Write Complete Interrupt Enable */ +#define RD_STATUS_REG (0x1 << 10) /* reads status reg */ +#define WE (0x1 << 11) /* Write Enable */ + +#define TX_LEN_SHIFT 0 +#define RX_LEN_SHIFT 4 +#define BANK_SHIFT 12 + +/* defines for status register */ +#define SR_WIP 0x1 /* Write in progress */ +#define SR_WEL 0x2 /* Write enable latch */ +#define SR_BP0 0x4 /* Block protect 0 */ +#define SR_BP1 0x8 /* Block protect 1 */ +#define SR_BP2 0x10 /* Block protect 2 */ +#define SR_SRWD 0x80 /* SR write protect */ +#define TFF 0x100 /* Transfer Finished Flag */ +#define WCF 0x200 /* Transfer Finished Flag */ +#define ERF1 0x400 /* Forbidden Write Request */ +#define ERF2 0x800 /* Forbidden Access */ + +#define WM_SHIFT 12 + +/* flash opcodes */ +#define OPCODE_RDID 0x9f /* Read JEDEC ID */ + +/* Flash Device Ids maintenance section */ + +/* data structure to maintain flash ids from different vendors */ +struct flash_device { + char *name; + u8 erase_cmd; + u32 device_id; + u32 pagesize; + unsigned long sectorsize; + unsigned long size_in_bytes; +}; + +#define FLASH_ID(n, es, id, psize, ssize, size) \ +{ \ + .name = n, \ + .erase_cmd = es, \ + .device_id = id, \ + .pagesize = psize, \ + .sectorsize = ssize, \ + .size_in_bytes = size \ +} + +static struct flash_device flash_devices[] = { + FLASH_ID("st m25p16" , 0xd8, 0x00152020, 0x100, 0x10000, 0x200000), + FLASH_ID("st m25p32" , 0xd8, 0x00162020, 0x100, 0x10000, 0x400000), + FLASH_ID("st m25p64" , 0xd8, 0x00172020, 0x100, 0x10000, 0x800000), + FLASH_ID("st m25p128" , 0xd8, 0x00182020, 0x100, 0x40000, 0x1000000), + FLASH_ID("st m25p05" , 0xd8, 0x00102020, 0x80 , 0x8000 , 0x10000), + FLASH_ID("st m25p10" , 0xd8, 0x00112020, 0x80 , 0x8000 , 0x20000), + FLASH_ID("st m25p20" , 0xd8, 0x00122020, 0x100, 0x10000, 0x40000), + FLASH_ID("st m25p40" , 0xd8, 0x00132020, 0x100, 0x10000, 0x80000), + FLASH_ID("st m25p80" , 0xd8, 0x00142020, 0x100, 0x10000, 0x100000), + FLASH_ID("st m45pe10" , 0xd8, 0x00114020, 0x100, 0x10000, 0x20000), + FLASH_ID("st m45pe20" , 0xd8, 0x00124020, 0x100, 0x10000, 0x40000), + FLASH_ID("st m45pe40" , 0xd8, 0x00134020, 0x100, 0x10000, 0x80000), + FLASH_ID("st m45pe80" , 0xd8, 0x00144020, 0x100, 0x10000, 0x100000), + FLASH_ID("sp s25fl004" , 0xd8, 0x00120201, 0x100, 0x10000, 0x80000), + FLASH_ID("sp s25fl008" , 0xd8, 0x00130201, 0x100, 0x10000, 0x100000), + FLASH_ID("sp s25fl016" , 0xd8, 0x00140201, 0x100, 0x10000, 0x200000), + FLASH_ID("sp s25fl032" , 0xd8, 0x00150201, 0x100, 0x10000, 0x400000), + FLASH_ID("sp s25fl064" , 0xd8, 0x00160201, 0x100, 0x10000, 0x800000), + FLASH_ID("atmel 25f512" , 0x52, 0x0065001F, 0x80 , 0x8000 , 0x10000), + FLASH_ID("atmel 25f1024" , 0x52, 0x0060001F, 0x100, 0x8000 , 0x20000), + FLASH_ID("atmel 25f2048" , 0x52, 0x0063001F, 0x100, 0x10000, 0x40000), + FLASH_ID("atmel 25f4096" , 0x52, 0x0064001F, 0x100, 0x10000, 0x80000), + FLASH_ID("atmel 25fs040" , 0xd7, 0x0004661F, 0x100, 0x10000, 0x80000), + FLASH_ID("mac 25l512" , 0xd8, 0x001020C2, 0x010, 0x10000, 0x10000), + FLASH_ID("mac 25l1005" , 0xd8, 0x001120C2, 0x010, 0x10000, 0x20000), + FLASH_ID("mac 25l2005" , 0xd8, 0x001220C2, 0x010, 0x10000, 0x40000), + FLASH_ID("mac 25l4005" , 0xd8, 0x001320C2, 0x010, 0x10000, 0x80000), + FLASH_ID("mac 25l4005a" , 0xd8, 0x001320C2, 0x010, 0x10000, 0x80000), + FLASH_ID("mac 25l8005" , 0xd8, 0x001420C2, 0x010, 0x10000, 0x100000), + FLASH_ID("mac 25l1605" , 0xd8, 0x001520C2, 0x100, 0x10000, 0x200000), + FLASH_ID("mac 25l1605a" , 0xd8, 0x001520C2, 0x010, 0x10000, 0x200000), + FLASH_ID("mac 25l3205" , 0xd8, 0x001620C2, 0x100, 0x10000, 0x400000), + FLASH_ID("mac 25l3205a" , 0xd8, 0x001620C2, 0x100, 0x10000, 0x400000), + FLASH_ID("mac 25l6405" , 0xd8, 0x001720C2, 0x100, 0x10000, 0x800000), +}; + +/* Define spear specific structures */ + +struct spear_snor_flash; + +/** + * struct spear_smi - Structure for SMI Device + * + * @clk: functional clock + * @status: current status register of SMI. + * @clk_rate: functional clock rate of SMI (default: SMI_MAX_CLOCK_FREQ) + * @lock: lock to prevent parallel access of SMI. + * @io_base: base address for registers of SMI. + * @pdev: platform device + * @cmd_complete: queue to wait for command completion of NOR-flash. + * @num_flashes: number of flashes actually present on board. + * @flash: separate structure for each Serial NOR-flash attached to SMI. + */ +struct spear_smi { + struct clk *clk; + u32 status; + unsigned long clk_rate; + struct mutex lock; + void __iomem *io_base; + struct platform_device *pdev; + wait_queue_head_t cmd_complete; + u32 num_flashes; + struct spear_snor_flash *flash[MAX_NUM_FLASH_CHIP]; +}; + +/** + * struct spear_snor_flash - Structure for Serial NOR Flash + * + * @bank: Bank number(0, 1, 2, 3) for each NOR-flash. + * @dev_id: Device ID of NOR-flash. + * @lock: lock to manage flash read, write and erase operations + * @mtd: MTD info for each NOR-flash. + * @num_parts: Total number of partition in each bank of NOR-flash. + * @parts: Partition info for each bank of NOR-flash. + * @page_size: Page size of NOR-flash. + * @base_addr: Base address of NOR-flash. + * @erase_cmd: erase command may vary on different flash types + * @fast_mode: flash supports read in fast mode + */ +struct spear_snor_flash { + u32 bank; + u32 dev_id; + struct mutex lock; + struct mtd_info mtd; + u32 num_parts; + struct mtd_partition *parts; + u32 page_size; + void __iomem *base_addr; + u8 erase_cmd; + u8 fast_mode; +}; + +static inline struct spear_snor_flash *get_flash_data(struct mtd_info *mtd) +{ + return container_of(mtd, struct spear_snor_flash, mtd); +} + +/** + * spear_smi_read_sr - Read status register of flash through SMI + * @dev: structure of SMI information. + * @bank: bank to which flash is connected + * + * This routine will return the status register of the flash chip present at the + * given bank. + */ +static int spear_smi_read_sr(struct spear_smi *dev, u32 bank) +{ + int ret; + u32 ctrlreg1; + + mutex_lock(&dev->lock); + dev->status = 0; /* Will be set in interrupt handler */ + + ctrlreg1 = readl(dev->io_base + SMI_CR1); + /* program smi in hw mode */ + writel(ctrlreg1 & ~(SW_MODE | WB_MODE), dev->io_base + SMI_CR1); + + /* performing a rsr instruction in hw mode */ + writel((bank << BANK_SHIFT) | RD_STATUS_REG | TFIE, + dev->io_base + SMI_CR2); + + /* wait for tff */ + ret = wait_event_interruptible_timeout(dev->cmd_complete, + dev->status & TFF, SMI_CMD_TIMEOUT); + + /* copy dev->status (lower 16 bits) in order to release lock */ + if (ret > 0) + ret = dev->status & 0xffff; + else if (ret == 0) + ret = -ETIMEDOUT; + + /* restore the ctrl regs state */ + writel(ctrlreg1, dev->io_base + SMI_CR1); + writel(0, dev->io_base + SMI_CR2); + mutex_unlock(&dev->lock); + + return ret; +} + +/** + * spear_smi_wait_till_ready - wait till flash is ready + * @dev: structure of SMI information. + * @bank: flash corresponding to this bank + * @timeout: timeout for busy wait condition + * + * This routine checks for WIP (write in progress) bit in Status register + * If successful the routine returns 0 else -EBUSY + */ +static int spear_smi_wait_till_ready(struct spear_smi *dev, u32 bank, + unsigned long timeout) +{ + unsigned long finish; + int status; + + finish = jiffies + timeout; + do { + status = spear_smi_read_sr(dev, bank); + if (status < 0) { + if (status == -ETIMEDOUT) + continue; /* try till finish */ + return status; + } else if (!(status & SR_WIP)) { + return 0; + } + + cond_resched(); + } while (!time_after_eq(jiffies, finish)); + + dev_err(&dev->pdev->dev, "smi controller is busy, timeout\n"); + return -EBUSY; +} + +/** + * spear_smi_int_handler - SMI Interrupt Handler. + * @irq: irq number + * @dev_id: structure of SMI device, embedded in dev_id. + * + * The handler clears all interrupt conditions and records the status in + * dev->status which is used by the driver later. + */ +static irqreturn_t spear_smi_int_handler(int irq, void *dev_id) +{ + u32 status = 0; + struct spear_smi *dev = dev_id; + + status = readl(dev->io_base + SMI_SR); + + if (unlikely(!status)) + return IRQ_NONE; + + /* clear all interrupt conditions */ + writel(0, dev->io_base + SMI_SR); + + /* copy the status register in dev->status */ + dev->status |= status; + + /* send the completion */ + wake_up_interruptible(&dev->cmd_complete); + + return IRQ_HANDLED; +} + +/** + * spear_smi_hw_init - initializes the smi controller. + * @dev: structure of smi device + * + * this routine initializes the smi controller wit the default values + */ +static void spear_smi_hw_init(struct spear_smi *dev) +{ + unsigned long rate = 0; + u32 prescale = 0; + u32 val; + + rate = clk_get_rate(dev->clk); + + /* functional clock of smi */ + prescale = DIV_ROUND_UP(rate, dev->clk_rate); + + /* + * setting the standard values, fast mode, prescaler for + * SMI_MAX_CLOCK_FREQ (50MHz) operation and bank enable + */ + val = HOLD1 | BANK_EN | DSEL_TIME | (prescale << 8); + + mutex_lock(&dev->lock); + /* clear all interrupt conditions */ + writel(0, dev->io_base + SMI_SR); + + writel(val, dev->io_base + SMI_CR1); + mutex_unlock(&dev->lock); +} + +/** + * get_flash_index - match chip id from a flash list. + * @flash_id: a valid nor flash chip id obtained from board. + * + * try to validate the chip id by matching from a list, if not found then simply + * returns negative. In case of success returns index in to the flash devices + * array. + */ +static int get_flash_index(u32 flash_id) +{ + int index; + + /* Matches chip-id to entire list of 'serial-nor flash' ids */ + for (index = 0; index < ARRAY_SIZE(flash_devices); index++) { + if (flash_devices[index].device_id == flash_id) + return index; + } + + /* Memory chip is not listed and not supported */ + return -ENODEV; +} + +/** + * spear_smi_write_enable - Enable the flash to do write operation + * @dev: structure of SMI device + * @bank: enable write for flash connected to this bank + * + * Set write enable latch with Write Enable command. + * Returns 0 on success. + */ +static int spear_smi_write_enable(struct spear_smi *dev, u32 bank) +{ + int ret; + u32 ctrlreg1; + + mutex_lock(&dev->lock); + dev->status = 0; /* Will be set in interrupt handler */ + + ctrlreg1 = readl(dev->io_base + SMI_CR1); + /* program smi in h/w mode */ + writel(ctrlreg1 & ~SW_MODE, dev->io_base + SMI_CR1); + + /* give the flash, write enable command */ + writel((bank << BANK_SHIFT) | WE | TFIE, dev->io_base + SMI_CR2); + + ret = wait_event_interruptible_timeout(dev->cmd_complete, + dev->status & TFF, SMI_CMD_TIMEOUT); + + /* restore the ctrl regs state */ + writel(ctrlreg1, dev->io_base + SMI_CR1); + writel(0, dev->io_base + SMI_CR2); + + if (ret == 0) { + ret = -EIO; + dev_err(&dev->pdev->dev, + "smi controller failed on write enable\n"); + } else if (ret > 0) { + /* check whether write mode status is set for required bank */ + if (dev->status & (1 << (bank + WM_SHIFT))) + ret = 0; + else { + dev_err(&dev->pdev->dev, "couldn't enable write\n"); + ret = -EIO; + } + } + + mutex_unlock(&dev->lock); + return ret; +} + +static inline u32 +get_sector_erase_cmd(struct spear_snor_flash *flash, u32 offset) +{ + u32 cmd; + u8 *x = (u8 *)&cmd; + + x[0] = flash->erase_cmd; + x[1] = offset >> 16; + x[2] = offset >> 8; + x[3] = offset; + + return cmd; +} + +/** + * spear_smi_erase_sector - erase one sector of flash + * @dev: structure of SMI information + * @command: erase command to be send + * @bank: bank to which this command needs to be send + * @bytes: size of command + * + * Erase one sector of flash memory at offset ``offset'' which is any + * address within the sector which should be erased. + * Returns 0 if successful, non-zero otherwise. + */ +static int spear_smi_erase_sector(struct spear_smi *dev, + u32 bank, u32 command, u32 bytes) +{ + u32 ctrlreg1 = 0; + int ret; + + ret = spear_smi_wait_till_ready(dev, bank, SMI_MAX_TIME_OUT); + if (ret) + return ret; + + ret = spear_smi_write_enable(dev, bank); + if (ret) + return ret; + + mutex_lock(&dev->lock); + + ctrlreg1 = readl(dev->io_base + SMI_CR1); + writel((ctrlreg1 | SW_MODE) & ~WB_MODE, dev->io_base + SMI_CR1); + + /* send command in sw mode */ + writel(command, dev->io_base + SMI_TR); + + writel((bank << BANK_SHIFT) | SEND | TFIE | (bytes << TX_LEN_SHIFT), + dev->io_base + SMI_CR2); + + ret = wait_event_interruptible_timeout(dev->cmd_complete, + dev->status & TFF, SMI_CMD_TIMEOUT); + + if (ret == 0) { + ret = -EIO; + dev_err(&dev->pdev->dev, "sector erase failed\n"); + } else if (ret > 0) + ret = 0; /* success */ + + /* restore ctrl regs */ + writel(ctrlreg1, dev->io_base + SMI_CR1); + writel(0, dev->io_base + SMI_CR2); + + mutex_unlock(&dev->lock); + return ret; +} + +/** + * spear_mtd_erase - perform flash erase operation as requested by user + * @mtd: Provides the memory characteristics + * @e_info: Provides the erase information + * + * Erase an address range on the flash chip. The address range may extend + * one or more erase sectors. Return an error is there is a problem erasing. + */ +static int spear_mtd_erase(struct mtd_info *mtd, struct erase_info *e_info) +{ + struct spear_snor_flash *flash = get_flash_data(mtd); + struct spear_smi *dev = mtd->priv; + u32 addr, command, bank; + int len, ret; + + if (!flash || !dev) + return -ENODEV; + + bank = flash->bank; + if (bank > dev->num_flashes - 1) { + dev_err(&dev->pdev->dev, "Invalid Bank Num"); + return -EINVAL; + } + + addr = e_info->addr; + len = e_info->len; + + mutex_lock(&flash->lock); + + /* now erase sectors in loop */ + while (len) { + command = get_sector_erase_cmd(flash, addr); + /* preparing the command for flash */ + ret = spear_smi_erase_sector(dev, bank, command, 4); + if (ret) { + e_info->state = MTD_ERASE_FAILED; + mutex_unlock(&flash->lock); + return ret; + } + addr += mtd->erasesize; + len -= mtd->erasesize; + } + + mutex_unlock(&flash->lock); + e_info->state = MTD_ERASE_DONE; + mtd_erase_callback(e_info); + + return 0; +} + +/** + * spear_mtd_read - performs flash read operation as requested by the user + * @mtd: MTD information of the memory bank + * @from: Address from which to start read + * @len: Number of bytes to be read + * @retlen: Fills the Number of bytes actually read + * @buf: Fills this after reading + * + * Read an address range from the flash chip. The address range + * may be any size provided it is within the physical boundaries. + * Returns 0 on success, non zero otherwise + */ +static int spear_mtd_read(struct mtd_info *mtd, loff_t from, size_t len, + size_t *retlen, u8 *buf) +{ + struct spear_snor_flash *flash = get_flash_data(mtd); + struct spear_smi *dev = mtd->priv; + void __iomem *src; + u32 ctrlreg1, val; + int ret; + + if (!flash || !dev) + return -ENODEV; + + if (flash->bank > dev->num_flashes - 1) { + dev_err(&dev->pdev->dev, "Invalid Bank Num"); + return -EINVAL; + } + + /* select address as per bank number */ + src = flash->base_addr + from; + + mutex_lock(&flash->lock); + + /* wait till previous write/erase is done. */ + ret = spear_smi_wait_till_ready(dev, flash->bank, SMI_MAX_TIME_OUT); + if (ret) { + mutex_unlock(&flash->lock); + return ret; + } + + mutex_lock(&dev->lock); + /* put smi in hw mode not wbt mode */ + ctrlreg1 = val = readl(dev->io_base + SMI_CR1); + val &= ~(SW_MODE | WB_MODE); + if (flash->fast_mode) + val |= FAST_MODE; + + writel(val, dev->io_base + SMI_CR1); + + memcpy_fromio(buf, src, len); + + /* restore ctrl reg1 */ + writel(ctrlreg1, dev->io_base + SMI_CR1); + mutex_unlock(&dev->lock); + + *retlen = len; + mutex_unlock(&flash->lock); + + return 0; +} + +static inline int spear_smi_cpy_toio(struct spear_smi *dev, u32 bank, + void __iomem *dest, const void *src, size_t len) +{ + int ret; + u32 ctrlreg1; + + /* wait until finished previous write command. */ + ret = spear_smi_wait_till_ready(dev, bank, SMI_MAX_TIME_OUT); + if (ret) + return ret; + + /* put smi in write enable */ + ret = spear_smi_write_enable(dev, bank); + if (ret) + return ret; + + /* put smi in hw, write burst mode */ + mutex_lock(&dev->lock); + + ctrlreg1 = readl(dev->io_base + SMI_CR1); + writel((ctrlreg1 | WB_MODE) & ~SW_MODE, dev->io_base + SMI_CR1); + + memcpy_toio(dest, src, len); + + writel(ctrlreg1, dev->io_base + SMI_CR1); + + mutex_unlock(&dev->lock); + return 0; +} + +/** + * spear_mtd_write - performs write operation as requested by the user. + * @mtd: MTD information of the memory bank. + * @to: Address to write. + * @len: Number of bytes to be written. + * @retlen: Number of bytes actually wrote. + * @buf: Buffer from which the data to be taken. + * + * Write an address range to the flash chip. Data must be written in + * flash_page_size chunks. The address range may be any size provided + * it is within the physical boundaries. + * Returns 0 on success, non zero otherwise + */ +static int spear_mtd_write(struct mtd_info *mtd, loff_t to, size_t len, + size_t *retlen, const u8 *buf) +{ + struct spear_snor_flash *flash = get_flash_data(mtd); + struct spear_smi *dev = mtd->priv; + void __iomem *dest; + u32 page_offset, page_size; + int ret; + + if (!flash || !dev) + return -ENODEV; + + if (flash->bank > dev->num_flashes - 1) { + dev_err(&dev->pdev->dev, "Invalid Bank Num"); + return -EINVAL; + } + + /* select address as per bank number */ + dest = flash->base_addr + to; + mutex_lock(&flash->lock); + + page_offset = (u32)to % flash->page_size; + + /* do if all the bytes fit onto one page */ + if (page_offset + len <= flash->page_size) { + ret = spear_smi_cpy_toio(dev, flash->bank, dest, buf, len); + if (!ret) + *retlen += len; + } else { + u32 i; + + /* the size of data remaining on the first page */ + page_size = flash->page_size - page_offset; + + ret = spear_smi_cpy_toio(dev, flash->bank, dest, buf, + page_size); + if (ret) + goto err_write; + else + *retlen += page_size; + + /* write everything in pagesize chunks */ + for (i = page_size; i < len; i += page_size) { + page_size = len - i; + if (page_size > flash->page_size) + page_size = flash->page_size; + + ret = spear_smi_cpy_toio(dev, flash->bank, dest + i, + buf + i, page_size); + if (ret) + break; + else + *retlen += page_size; + } + } + +err_write: + mutex_unlock(&flash->lock); + + return ret; +} + +/** + * spear_smi_probe_flash - Detects the NOR Flash chip. + * @dev: structure of SMI information. + * @bank: bank on which flash must be probed + * + * This routine will check whether there exists a flash chip on a given memory + * bank ID. + * Return index of the probed flash in flash devices structure + */ +static int spear_smi_probe_flash(struct spear_smi *dev, u32 bank) +{ + int ret; + u32 val = 0; + + ret = spear_smi_wait_till_ready(dev, bank, SMI_PROBE_TIMEOUT); + if (ret) + return ret; + + mutex_lock(&dev->lock); + + dev->status = 0; /* Will be set in interrupt handler */ + /* put smi in sw mode */ + val = readl(dev->io_base + SMI_CR1); + writel(val | SW_MODE, dev->io_base + SMI_CR1); + + /* send readid command in sw mode */ + writel(OPCODE_RDID, dev->io_base + SMI_TR); + + val = (bank << BANK_SHIFT) | SEND | (1 << TX_LEN_SHIFT) | + (3 << RX_LEN_SHIFT) | TFIE; + writel(val, dev->io_base + SMI_CR2); + + /* wait for TFF */ + ret = wait_event_interruptible_timeout(dev->cmd_complete, + dev->status & TFF, SMI_CMD_TIMEOUT); + if (ret <= 0) { + ret = -ENODEV; + goto err_probe; + } + + /* get memory chip id */ + val = readl(dev->io_base + SMI_RR); + val &= 0x00ffffff; + ret = get_flash_index(val); + +err_probe: + /* clear sw mode */ + val = readl(dev->io_base + SMI_CR1); + writel(val & ~SW_MODE, dev->io_base + SMI_CR1); + + mutex_unlock(&dev->lock); + return ret; +} + + +#ifdef CONFIG_OF +static int spear_smi_probe_config_dt(struct platform_device *pdev, + struct device_node *np) +{ + struct spear_smi_plat_data *pdata = dev_get_platdata(&pdev->dev); + struct device_node *pp = NULL; + const __be32 *addr; + u32 val; + int len; + int i = 0; + + if (!np) + return -ENODEV; + + of_property_read_u32(np, "clock-rate", &val); + pdata->clk_rate = val; + + pdata->board_flash_info = devm_kzalloc(&pdev->dev, + sizeof(*pdata->board_flash_info), + GFP_KERNEL); + + /* Fill structs for each subnode (flash device) */ + while ((pp = of_get_next_child(np, pp))) { + struct spear_smi_flash_info *flash_info; + + flash_info = &pdata->board_flash_info[i]; + pdata->np[i] = pp; + + /* Read base-addr and size from DT */ + addr = of_get_property(pp, "reg", &len); + pdata->board_flash_info->mem_base = be32_to_cpup(&addr[0]); + pdata->board_flash_info->size = be32_to_cpup(&addr[1]); + + if (of_get_property(pp, "st,smi-fast-mode", NULL)) + pdata->board_flash_info->fast_mode = 1; + + i++; + } + + pdata->num_flashes = i; + + return 0; +} +#else +static int spear_smi_probe_config_dt(struct platform_device *pdev, + struct device_node *np) +{ + return -ENOSYS; +} +#endif + +static int spear_smi_setup_banks(struct platform_device *pdev, + u32 bank, struct device_node *np) +{ + struct spear_smi *dev = platform_get_drvdata(pdev); + struct mtd_part_parser_data ppdata = {}; + struct spear_smi_flash_info *flash_info; + struct spear_smi_plat_data *pdata; + struct spear_snor_flash *flash; + struct mtd_partition *parts = NULL; + int count = 0; + int flash_index; + int ret = 0; + + pdata = dev_get_platdata(&pdev->dev); + if (bank > pdata->num_flashes - 1) + return -EINVAL; + + flash_info = &pdata->board_flash_info[bank]; + if (!flash_info) + return -ENODEV; + + flash = devm_kzalloc(&pdev->dev, sizeof(*flash), GFP_ATOMIC); + if (!flash) + return -ENOMEM; + flash->bank = bank; + flash->fast_mode = flash_info->fast_mode ? 1 : 0; + mutex_init(&flash->lock); + + /* verify whether nor flash is really present on board */ + flash_index = spear_smi_probe_flash(dev, bank); + if (flash_index < 0) { + dev_info(&dev->pdev->dev, "smi-nor%d not found\n", bank); + return flash_index; + } + /* map the memory for nor flash chip */ + flash->base_addr = devm_ioremap(&pdev->dev, flash_info->mem_base, + flash_info->size); + if (!flash->base_addr) + return -EIO; + + dev->flash[bank] = flash; + flash->mtd.priv = dev; + + if (flash_info->name) + flash->mtd.name = flash_info->name; + else + flash->mtd.name = flash_devices[flash_index].name; + + flash->mtd.type = MTD_NORFLASH; + flash->mtd.writesize = 1; + flash->mtd.flags = MTD_CAP_NORFLASH; + flash->mtd.size = flash_info->size; + flash->mtd.erasesize = flash_devices[flash_index].sectorsize; + flash->page_size = flash_devices[flash_index].pagesize; + flash->mtd.writebufsize = flash->page_size; + flash->erase_cmd = flash_devices[flash_index].erase_cmd; + flash->mtd._erase = spear_mtd_erase; + flash->mtd._read = spear_mtd_read; + flash->mtd._write = spear_mtd_write; + flash->dev_id = flash_devices[flash_index].device_id; + + dev_info(&dev->pdev->dev, "mtd .name=%s .size=%llx(%lluM)\n", + flash->mtd.name, flash->mtd.size, + flash->mtd.size / (1024 * 1024)); + + dev_info(&dev->pdev->dev, ".erasesize = 0x%x(%uK)\n", + flash->mtd.erasesize, flash->mtd.erasesize / 1024); + +#ifndef CONFIG_OF + if (flash_info->partitions) { + parts = flash_info->partitions; + count = flash_info->nr_partitions; + } +#endif + ppdata.of_node = np; + + ret = mtd_device_parse_register(&flash->mtd, NULL, &ppdata, parts, + count); + if (ret) { + dev_err(&dev->pdev->dev, "Err MTD partition=%d\n", ret); + return ret; + } + + return 0; +} + +/** + * spear_smi_probe - Entry routine + * @pdev: platform device structure + * + * This is the first routine which gets invoked during booting and does all + * initialization/allocation work. The routine looks for available memory banks, + * and do proper init for any found one. + * Returns 0 on success, non zero otherwise + */ +static int spear_smi_probe(struct platform_device *pdev) +{ + struct device_node *np = pdev->dev.of_node; + struct spear_smi_plat_data *pdata = NULL; + struct spear_smi *dev; + struct resource *smi_base; + int irq, ret = 0; + int i; + + if (np) { + pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL); + if (!pdata) { + ret = -ENOMEM; + goto err; + } + pdev->dev.platform_data = pdata; + ret = spear_smi_probe_config_dt(pdev, np); + if (ret) { + ret = -ENODEV; + dev_err(&pdev->dev, "no platform data\n"); + goto err; + } + } else { + pdata = dev_get_platdata(&pdev->dev); + if (!pdata) { + ret = -ENODEV; + dev_err(&pdev->dev, "no platform data\n"); + goto err; + } + } + + irq = platform_get_irq(pdev, 0); + if (irq < 0) { + ret = -ENODEV; + dev_err(&pdev->dev, "invalid smi irq\n"); + goto err; + } + + dev = devm_kzalloc(&pdev->dev, sizeof(*dev), GFP_ATOMIC); + if (!dev) { + ret = -ENOMEM; + goto err; + } + + smi_base = platform_get_resource(pdev, IORESOURCE_MEM, 0); + + dev->io_base = devm_ioremap_resource(&pdev->dev, smi_base); + if (IS_ERR(dev->io_base)) { + ret = PTR_ERR(dev->io_base); + goto err; + } + + dev->pdev = pdev; + dev->clk_rate = pdata->clk_rate; + + if (dev->clk_rate > SMI_MAX_CLOCK_FREQ) + dev->clk_rate = SMI_MAX_CLOCK_FREQ; + + dev->num_flashes = pdata->num_flashes; + + if (dev->num_flashes > MAX_NUM_FLASH_CHIP) { + dev_err(&pdev->dev, "exceeding max number of flashes\n"); + dev->num_flashes = MAX_NUM_FLASH_CHIP; + } + + dev->clk = devm_clk_get(&pdev->dev, NULL); + if (IS_ERR(dev->clk)) { + ret = PTR_ERR(dev->clk); + goto err; + } + + ret = clk_prepare_enable(dev->clk); + if (ret) + goto err; + + ret = devm_request_irq(&pdev->dev, irq, spear_smi_int_handler, 0, + pdev->name, dev); + if (ret) { + dev_err(&dev->pdev->dev, "SMI IRQ allocation failed\n"); + goto err_irq; + } + + mutex_init(&dev->lock); + init_waitqueue_head(&dev->cmd_complete); + spear_smi_hw_init(dev); + platform_set_drvdata(pdev, dev); + + /* loop for each serial nor-flash which is connected to smi */ + for (i = 0; i < dev->num_flashes; i++) { + ret = spear_smi_setup_banks(pdev, i, pdata->np[i]); + if (ret) { + dev_err(&dev->pdev->dev, "bank setup failed\n"); + goto err_irq; + } + } + + return 0; + +err_irq: + clk_disable_unprepare(dev->clk); +err: + return ret; +} + +/** + * spear_smi_remove - Exit routine + * @pdev: platform device structure + * + * free all allocations and delete the partitions. + */ +static int spear_smi_remove(struct platform_device *pdev) +{ + struct spear_smi *dev; + struct spear_snor_flash *flash; + int ret, i; + + dev = platform_get_drvdata(pdev); + if (!dev) { + dev_err(&pdev->dev, "dev is null\n"); + return -ENODEV; + } + + /* clean up for all nor flash */ + for (i = 0; i < dev->num_flashes; i++) { + flash = dev->flash[i]; + if (!flash) + continue; + + /* clean up mtd stuff */ + ret = mtd_device_unregister(&flash->mtd); + if (ret) + dev_err(&pdev->dev, "error removing mtd\n"); + } + + clk_disable_unprepare(dev->clk); + + return 0; +} + +#ifdef CONFIG_PM_SLEEP +static int spear_smi_suspend(struct device *dev) +{ + struct spear_smi *sdev = dev_get_drvdata(dev); + + if (sdev && sdev->clk) + clk_disable_unprepare(sdev->clk); + + return 0; +} + +static int spear_smi_resume(struct device *dev) +{ + struct spear_smi *sdev = dev_get_drvdata(dev); + int ret = -EPERM; + + if (sdev && sdev->clk) + ret = clk_prepare_enable(sdev->clk); + + if (!ret) + spear_smi_hw_init(sdev); + return ret; +} +#endif + +static SIMPLE_DEV_PM_OPS(spear_smi_pm_ops, spear_smi_suspend, spear_smi_resume); + +#ifdef CONFIG_OF +static const struct of_device_id spear_smi_id_table[] = { + { .compatible = "st,spear600-smi" }, + {} +}; +MODULE_DEVICE_TABLE(of, spear_smi_id_table); +#endif + +static struct platform_driver spear_smi_driver = { + .driver = { + .name = "smi", + .bus = &platform_bus_type, + .owner = THIS_MODULE, + .of_match_table = of_match_ptr(spear_smi_id_table), + .pm = &spear_smi_pm_ops, + }, + .probe = spear_smi_probe, + .remove = spear_smi_remove, +}; +module_platform_driver(spear_smi_driver); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Ashish Priyadarshi, Shiraz Hashim <shiraz.linux.kernel@gmail.com>"); +MODULE_DESCRIPTION("MTD SMI driver for serial nor flash chips"); diff --git a/drivers/mtd/devices/sst25l.c b/drivers/mtd/devices/sst25l.c index 5fc198350b9..c63ecbcad0b 100644 --- a/drivers/mtd/devices/sst25l.c +++ b/drivers/mtd/devices/sst25l.c @@ -15,7 +15,6 @@ * */ -#include <linux/init.h> #include <linux/module.h> #include <linux/device.h> #include <linux/mutex.h> @@ -64,7 +63,7 @@ struct flash_info { #define to_sst25l_flash(x) container_of(x, struct sst25l_flash, mtd) -static struct flash_info __devinitdata sst25l_flash_info[] = { +static struct flash_info sst25l_flash_info[] = { {"sst25lf020a", 0xbf43, 256, 1024, 4096}, {"sst25lf040a", 0xbf44, 256, 2048, 4096}, }; @@ -175,9 +174,6 @@ static int sst25l_erase(struct mtd_info *mtd, struct erase_info *instr) int err; /* Sanity checks */ - if (instr->addr + instr->len > flash->mtd.size) - return -EINVAL; - if ((uint32_t)instr->len % mtd->erasesize) return -EINVAL; @@ -223,16 +219,6 @@ static int sst25l_read(struct mtd_info *mtd, loff_t from, size_t len, unsigned char command[4]; int ret; - /* Sanity checking */ - if (len == 0) - return 0; - - if (from + len > flash->mtd.size) - return -EINVAL; - - if (retlen) - *retlen = 0; - spi_message_init(&message); memset(&transfer, 0, sizeof(transfer)); @@ -274,13 +260,6 @@ static int sst25l_write(struct mtd_info *mtd, loff_t to, size_t len, int i, j, ret, bytes, copied = 0; unsigned char command[5]; - /* Sanity checks */ - if (!len) - return 0; - - if (to + len > flash->mtd.size) - return -EINVAL; - if ((uint32_t)to % mtd->writesize) return -EINVAL; @@ -333,7 +312,7 @@ out: return ret; } -static struct flash_info *__devinit sst25l_match_device(struct spi_device *spi) +static struct flash_info *sst25l_match_device(struct spi_device *spi) { struct flash_info *flash_info = NULL; struct spi_message m; @@ -373,7 +352,7 @@ static struct flash_info *__devinit sst25l_match_device(struct spi_device *spi) return flash_info; } -static int __devinit sst25l_probe(struct spi_device *spi) +static int sst25l_probe(struct spi_device *spi) { struct flash_info *flash_info; struct sst25l_flash *flash; @@ -384,15 +363,15 @@ static int __devinit sst25l_probe(struct spi_device *spi) if (!flash_info) return -ENODEV; - flash = kzalloc(sizeof(struct sst25l_flash), GFP_KERNEL); + flash = devm_kzalloc(&spi->dev, sizeof(*flash), GFP_KERNEL); if (!flash) return -ENOMEM; flash->spi = spi; mutex_init(&flash->lock); - dev_set_drvdata(&spi->dev, flash); + spi_set_drvdata(spi, flash); - data = spi->dev.platform_data; + data = dev_get_platdata(&spi->dev); if (data && data->name) flash->mtd.name = data->name; else @@ -402,10 +381,11 @@ static int __devinit sst25l_probe(struct spi_device *spi) flash->mtd.flags = MTD_CAP_NORFLASH; flash->mtd.erasesize = flash_info->erase_size; flash->mtd.writesize = flash_info->page_size; + flash->mtd.writebufsize = flash_info->page_size; flash->mtd.size = flash_info->page_size * flash_info->nr_pages; - flash->mtd.erase = sst25l_erase; - flash->mtd.read = sst25l_read; - flash->mtd.write = sst25l_write; + flash->mtd._erase = sst25l_erase; + flash->mtd._read = sst25l_read; + flash->mtd._write = sst25l_write; dev_info(&spi->dev, "%s (%lld KiB)\n", flash_info->name, (long long)flash->mtd.size >> 10); @@ -418,27 +398,20 @@ static int __devinit sst25l_probe(struct spi_device *spi) flash->mtd.numeraseregions); - ret = mtd_device_parse_register(&flash->mtd, NULL, 0, - data ? data->parts : NULL, - data ? data->nr_parts : 0); - if (ret) { - kfree(flash); - dev_set_drvdata(&spi->dev, NULL); + ret = mtd_device_parse_register(&flash->mtd, NULL, NULL, + data ? data->parts : NULL, + data ? data->nr_parts : 0); + if (ret) return -ENODEV; - } return 0; } -static int __devexit sst25l_remove(struct spi_device *spi) +static int sst25l_remove(struct spi_device *spi) { - struct sst25l_flash *flash = dev_get_drvdata(&spi->dev); - int ret; + struct sst25l_flash *flash = spi_get_drvdata(spi); - ret = mtd_device_unregister(&flash->mtd); - if (ret == 0) - kfree(flash); - return ret; + return mtd_device_unregister(&flash->mtd); } static struct spi_driver sst25l_driver = { @@ -447,21 +420,10 @@ static struct spi_driver sst25l_driver = { .owner = THIS_MODULE, }, .probe = sst25l_probe, - .remove = __devexit_p(sst25l_remove), + .remove = sst25l_remove, }; -static int __init sst25l_init(void) -{ - return spi_register_driver(&sst25l_driver); -} - -static void __exit sst25l_exit(void) -{ - spi_unregister_driver(&sst25l_driver); -} - -module_init(sst25l_init); -module_exit(sst25l_exit); +module_spi_driver(sst25l_driver); MODULE_DESCRIPTION("MTD SPI driver for SST25L Flash chips"); MODULE_AUTHOR("Andre Renaud <andre@bluewatersys.com>, " diff --git a/drivers/mtd/devices/st_spi_fsm.c b/drivers/mtd/devices/st_spi_fsm.c new file mode 100644 index 00000000000..d252514d3e9 --- /dev/null +++ b/drivers/mtd/devices/st_spi_fsm.c @@ -0,0 +1,2080 @@ +/* + * st_spi_fsm.c - ST Fast Sequence Mode (FSM) Serial Flash Controller + * + * Author: Angus Clark <angus.clark@st.com> + * + * Copyright (C) 2010-2014 STMicroelectronics Limited + * + * JEDEC probe based on drivers/mtd/devices/m25p80.c + * + * This code is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/regmap.h> +#include <linux/platform_device.h> +#include <linux/mfd/syscon.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/partitions.h> +#include <linux/mtd/spi-nor.h> +#include <linux/sched.h> +#include <linux/delay.h> +#include <linux/io.h> +#include <linux/of.h> + +#include "serial_flash_cmds.h" + +/* + * FSM SPI Controller Registers + */ +#define SPI_CLOCKDIV 0x0010 +#define SPI_MODESELECT 0x0018 +#define SPI_CONFIGDATA 0x0020 +#define SPI_STA_MODE_CHANGE 0x0028 +#define SPI_FAST_SEQ_TRANSFER_SIZE 0x0100 +#define SPI_FAST_SEQ_ADD1 0x0104 +#define SPI_FAST_SEQ_ADD2 0x0108 +#define SPI_FAST_SEQ_ADD_CFG 0x010c +#define SPI_FAST_SEQ_OPC1 0x0110 +#define SPI_FAST_SEQ_OPC2 0x0114 +#define SPI_FAST_SEQ_OPC3 0x0118 +#define SPI_FAST_SEQ_OPC4 0x011c +#define SPI_FAST_SEQ_OPC5 0x0120 +#define SPI_MODE_BITS 0x0124 +#define SPI_DUMMY_BITS 0x0128 +#define SPI_FAST_SEQ_FLASH_STA_DATA 0x012c +#define SPI_FAST_SEQ_1 0x0130 +#define SPI_FAST_SEQ_2 0x0134 +#define SPI_FAST_SEQ_3 0x0138 +#define SPI_FAST_SEQ_4 0x013c +#define SPI_FAST_SEQ_CFG 0x0140 +#define SPI_FAST_SEQ_STA 0x0144 +#define SPI_QUAD_BOOT_SEQ_INIT_1 0x0148 +#define SPI_QUAD_BOOT_SEQ_INIT_2 0x014c +#define SPI_QUAD_BOOT_READ_SEQ_1 0x0150 +#define SPI_QUAD_BOOT_READ_SEQ_2 0x0154 +#define SPI_PROGRAM_ERASE_TIME 0x0158 +#define SPI_MULT_PAGE_REPEAT_SEQ_1 0x015c +#define SPI_MULT_PAGE_REPEAT_SEQ_2 0x0160 +#define SPI_STATUS_WR_TIME_REG 0x0164 +#define SPI_FAST_SEQ_DATA_REG 0x0300 + +/* + * Register: SPI_MODESELECT + */ +#define SPI_MODESELECT_CONTIG 0x01 +#define SPI_MODESELECT_FASTREAD 0x02 +#define SPI_MODESELECT_DUALIO 0x04 +#define SPI_MODESELECT_FSM 0x08 +#define SPI_MODESELECT_QUADBOOT 0x10 + +/* + * Register: SPI_CONFIGDATA + */ +#define SPI_CFG_DEVICE_ST 0x1 +#define SPI_CFG_DEVICE_ATMEL 0x4 +#define SPI_CFG_MIN_CS_HIGH(x) (((x) & 0xfff) << 4) +#define SPI_CFG_CS_SETUPHOLD(x) (((x) & 0xff) << 16) +#define SPI_CFG_DATA_HOLD(x) (((x) & 0xff) << 24) + +#define SPI_CFG_DEFAULT_MIN_CS_HIGH SPI_CFG_MIN_CS_HIGH(0x0AA) +#define SPI_CFG_DEFAULT_CS_SETUPHOLD SPI_CFG_CS_SETUPHOLD(0xA0) +#define SPI_CFG_DEFAULT_DATA_HOLD SPI_CFG_DATA_HOLD(0x00) + +/* + * Register: SPI_FAST_SEQ_TRANSFER_SIZE + */ +#define TRANSFER_SIZE(x) ((x) * 8) + +/* + * Register: SPI_FAST_SEQ_ADD_CFG + */ +#define ADR_CFG_CYCLES_ADD1(x) ((x) << 0) +#define ADR_CFG_PADS_1_ADD1 (0x0 << 6) +#define ADR_CFG_PADS_2_ADD1 (0x1 << 6) +#define ADR_CFG_PADS_4_ADD1 (0x3 << 6) +#define ADR_CFG_CSDEASSERT_ADD1 (1 << 8) +#define ADR_CFG_CYCLES_ADD2(x) ((x) << (0+16)) +#define ADR_CFG_PADS_1_ADD2 (0x0 << (6+16)) +#define ADR_CFG_PADS_2_ADD2 (0x1 << (6+16)) +#define ADR_CFG_PADS_4_ADD2 (0x3 << (6+16)) +#define ADR_CFG_CSDEASSERT_ADD2 (1 << (8+16)) + +/* + * Register: SPI_FAST_SEQ_n + */ +#define SEQ_OPC_OPCODE(x) ((x) << 0) +#define SEQ_OPC_CYCLES(x) ((x) << 8) +#define SEQ_OPC_PADS_1 (0x0 << 14) +#define SEQ_OPC_PADS_2 (0x1 << 14) +#define SEQ_OPC_PADS_4 (0x3 << 14) +#define SEQ_OPC_CSDEASSERT (1 << 16) + +/* + * Register: SPI_FAST_SEQ_CFG + */ +#define SEQ_CFG_STARTSEQ (1 << 0) +#define SEQ_CFG_SWRESET (1 << 5) +#define SEQ_CFG_CSDEASSERT (1 << 6) +#define SEQ_CFG_READNOTWRITE (1 << 7) +#define SEQ_CFG_ERASE (1 << 8) +#define SEQ_CFG_PADS_1 (0x0 << 16) +#define SEQ_CFG_PADS_2 (0x1 << 16) +#define SEQ_CFG_PADS_4 (0x3 << 16) + +/* + * Register: SPI_MODE_BITS + */ +#define MODE_DATA(x) (x & 0xff) +#define MODE_CYCLES(x) ((x & 0x3f) << 16) +#define MODE_PADS_1 (0x0 << 22) +#define MODE_PADS_2 (0x1 << 22) +#define MODE_PADS_4 (0x3 << 22) +#define DUMMY_CSDEASSERT (1 << 24) + +/* + * Register: SPI_DUMMY_BITS + */ +#define DUMMY_CYCLES(x) ((x & 0x3f) << 16) +#define DUMMY_PADS_1 (0x0 << 22) +#define DUMMY_PADS_2 (0x1 << 22) +#define DUMMY_PADS_4 (0x3 << 22) +#define DUMMY_CSDEASSERT (1 << 24) + +/* + * Register: SPI_FAST_SEQ_FLASH_STA_DATA + */ +#define STA_DATA_BYTE1(x) ((x & 0xff) << 0) +#define STA_DATA_BYTE2(x) ((x & 0xff) << 8) +#define STA_PADS_1 (0x0 << 16) +#define STA_PADS_2 (0x1 << 16) +#define STA_PADS_4 (0x3 << 16) +#define STA_CSDEASSERT (0x1 << 20) +#define STA_RDNOTWR (0x1 << 21) + +/* + * FSM SPI Instruction Opcodes + */ +#define STFSM_OPC_CMD 0x1 +#define STFSM_OPC_ADD 0x2 +#define STFSM_OPC_STA 0x3 +#define STFSM_OPC_MODE 0x4 +#define STFSM_OPC_DUMMY 0x5 +#define STFSM_OPC_DATA 0x6 +#define STFSM_OPC_WAIT 0x7 +#define STFSM_OPC_JUMP 0x8 +#define STFSM_OPC_GOTO 0x9 +#define STFSM_OPC_STOP 0xF + +/* + * FSM SPI Instructions (== opcode + operand). + */ +#define STFSM_INSTR(cmd, op) ((cmd) | ((op) << 4)) + +#define STFSM_INST_CMD1 STFSM_INSTR(STFSM_OPC_CMD, 1) +#define STFSM_INST_CMD2 STFSM_INSTR(STFSM_OPC_CMD, 2) +#define STFSM_INST_CMD3 STFSM_INSTR(STFSM_OPC_CMD, 3) +#define STFSM_INST_CMD4 STFSM_INSTR(STFSM_OPC_CMD, 4) +#define STFSM_INST_CMD5 STFSM_INSTR(STFSM_OPC_CMD, 5) +#define STFSM_INST_ADD1 STFSM_INSTR(STFSM_OPC_ADD, 1) +#define STFSM_INST_ADD2 STFSM_INSTR(STFSM_OPC_ADD, 2) + +#define STFSM_INST_DATA_WRITE STFSM_INSTR(STFSM_OPC_DATA, 1) +#define STFSM_INST_DATA_READ STFSM_INSTR(STFSM_OPC_DATA, 2) + +#define STFSM_INST_STA_RD1 STFSM_INSTR(STFSM_OPC_STA, 0x1) +#define STFSM_INST_STA_WR1 STFSM_INSTR(STFSM_OPC_STA, 0x1) +#define STFSM_INST_STA_RD2 STFSM_INSTR(STFSM_OPC_STA, 0x2) +#define STFSM_INST_STA_WR1_2 STFSM_INSTR(STFSM_OPC_STA, 0x3) + +#define STFSM_INST_MODE STFSM_INSTR(STFSM_OPC_MODE, 0) +#define STFSM_INST_DUMMY STFSM_INSTR(STFSM_OPC_DUMMY, 0) +#define STFSM_INST_WAIT STFSM_INSTR(STFSM_OPC_WAIT, 0) +#define STFSM_INST_STOP STFSM_INSTR(STFSM_OPC_STOP, 0) + +#define STFSM_DEFAULT_EMI_FREQ 100000000UL /* 100 MHz */ +#define STFSM_DEFAULT_WR_TIME (STFSM_DEFAULT_EMI_FREQ * (15/1000)) /* 15ms */ + +#define STFSM_FLASH_SAFE_FREQ 10000000UL /* 10 MHz */ + +#define STFSM_MAX_WAIT_SEQ_MS 1000 /* FSM execution time */ + +/* S25FLxxxS commands */ +#define S25FL_CMD_WRITE4_1_1_4 0x34 +#define S25FL_CMD_SE4 0xdc +#define S25FL_CMD_CLSR 0x30 +#define S25FL_CMD_DYBWR 0xe1 +#define S25FL_CMD_DYBRD 0xe0 +#define S25FL_CMD_WRITE4 0x12 /* Note, opcode clashes with + * 'SPINOR_OP_WRITE_1_4_4' + * as found on N25Qxxx devices! */ + +/* Status register */ +#define FLASH_STATUS_BUSY 0x01 +#define FLASH_STATUS_WEL 0x02 +#define FLASH_STATUS_BP0 0x04 +#define FLASH_STATUS_BP1 0x08 +#define FLASH_STATUS_BP2 0x10 +#define FLASH_STATUS_SRWP0 0x80 +#define FLASH_STATUS_TIMEOUT 0xff +/* S25FL Error Flags */ +#define S25FL_STATUS_E_ERR 0x20 +#define S25FL_STATUS_P_ERR 0x40 + +#define N25Q_CMD_WRVCR 0x81 +#define N25Q_CMD_RDVCR 0x85 +#define N25Q_CMD_RDVECR 0x65 +#define N25Q_CMD_RDNVCR 0xb5 +#define N25Q_CMD_WRNVCR 0xb1 + +#define FLASH_PAGESIZE 256 /* In Bytes */ +#define FLASH_PAGESIZE_32 (FLASH_PAGESIZE / 4) /* In uint32_t */ +#define FLASH_MAX_BUSY_WAIT (300 * HZ) /* Maximum 'CHIPERASE' time */ + +/* + * Flags to tweak operation of default read/write/erase routines + */ +#define CFG_READ_TOGGLE_32BIT_ADDR 0x00000001 +#define CFG_WRITE_TOGGLE_32BIT_ADDR 0x00000002 +#define CFG_ERASESEC_TOGGLE_32BIT_ADDR 0x00000008 +#define CFG_S25FL_CHECK_ERROR_FLAGS 0x00000010 + +struct stfsm_seq { + uint32_t data_size; + uint32_t addr1; + uint32_t addr2; + uint32_t addr_cfg; + uint32_t seq_opc[5]; + uint32_t mode; + uint32_t dummy; + uint32_t status; + uint8_t seq[16]; + uint32_t seq_cfg; +} __packed __aligned(4); + +struct stfsm { + struct device *dev; + void __iomem *base; + struct resource *region; + struct mtd_info mtd; + struct mutex lock; + struct flash_info *info; + + uint32_t configuration; + uint32_t fifo_dir_delay; + bool booted_from_spi; + bool reset_signal; + bool reset_por; + + struct stfsm_seq stfsm_seq_read; + struct stfsm_seq stfsm_seq_write; + struct stfsm_seq stfsm_seq_en_32bit_addr; +}; + +/* Parameters to configure a READ or WRITE FSM sequence */ +struct seq_rw_config { + uint32_t flags; /* flags to support config */ + uint8_t cmd; /* FLASH command */ + int write; /* Write Sequence */ + uint8_t addr_pads; /* No. of addr pads (MODE & DUMMY) */ + uint8_t data_pads; /* No. of data pads */ + uint8_t mode_data; /* MODE data */ + uint8_t mode_cycles; /* No. of MODE cycles */ + uint8_t dummy_cycles; /* No. of DUMMY cycles */ +}; + +/* SPI Flash Device Table */ +struct flash_info { + char *name; + /* + * JEDEC id zero means "no ID" (most older chips); otherwise it has + * a high byte of zero plus three data bytes: the manufacturer id, + * then a two byte device id. + */ + u32 jedec_id; + u16 ext_id; + /* + * The size listed here is what works with SPINOR_OP_SE, which isn't + * necessarily called a "sector" by the vendor. + */ + unsigned sector_size; + u16 n_sectors; + u32 flags; + /* + * Note, where FAST_READ is supported, freq_max specifies the + * FAST_READ frequency, not the READ frequency. + */ + u32 max_freq; + int (*config)(struct stfsm *); +}; + +static int stfsm_n25q_config(struct stfsm *fsm); +static int stfsm_mx25_config(struct stfsm *fsm); +static int stfsm_s25fl_config(struct stfsm *fsm); +static int stfsm_w25q_config(struct stfsm *fsm); + +static struct flash_info flash_types[] = { + /* + * ST Microelectronics/Numonyx -- + * (newer production versions may have feature updates + * (eg faster operating frequency) + */ +#define M25P_FLAG (FLASH_FLAG_READ_WRITE | FLASH_FLAG_READ_FAST) + { "m25p40", 0x202013, 0, 64 * 1024, 8, M25P_FLAG, 25, NULL }, + { "m25p80", 0x202014, 0, 64 * 1024, 16, M25P_FLAG, 25, NULL }, + { "m25p16", 0x202015, 0, 64 * 1024, 32, M25P_FLAG, 25, NULL }, + { "m25p32", 0x202016, 0, 64 * 1024, 64, M25P_FLAG, 50, NULL }, + { "m25p64", 0x202017, 0, 64 * 1024, 128, M25P_FLAG, 50, NULL }, + { "m25p128", 0x202018, 0, 256 * 1024, 64, M25P_FLAG, 50, NULL }, + +#define M25PX_FLAG (FLASH_FLAG_READ_WRITE | \ + FLASH_FLAG_READ_FAST | \ + FLASH_FLAG_READ_1_1_2 | \ + FLASH_FLAG_WRITE_1_1_2) + { "m25px32", 0x207116, 0, 64 * 1024, 64, M25PX_FLAG, 75, NULL }, + { "m25px64", 0x207117, 0, 64 * 1024, 128, M25PX_FLAG, 75, NULL }, + + /* Macronix MX25xxx + * - Support for 'FLASH_FLAG_WRITE_1_4_4' is omitted for devices + * where operating frequency must be reduced. + */ +#define MX25_FLAG (FLASH_FLAG_READ_WRITE | \ + FLASH_FLAG_READ_FAST | \ + FLASH_FLAG_READ_1_1_2 | \ + FLASH_FLAG_READ_1_2_2 | \ + FLASH_FLAG_READ_1_1_4 | \ + FLASH_FLAG_SE_4K | \ + FLASH_FLAG_SE_32K) + { "mx25l3255e", 0xc29e16, 0, 64 * 1024, 64, + (MX25_FLAG | FLASH_FLAG_WRITE_1_4_4), 86, + stfsm_mx25_config}, + { "mx25l25635e", 0xc22019, 0, 64*1024, 512, + (MX25_FLAG | FLASH_FLAG_32BIT_ADDR | FLASH_FLAG_RESET), 70, + stfsm_mx25_config }, + { "mx25l25655e", 0xc22619, 0, 64*1024, 512, + (MX25_FLAG | FLASH_FLAG_32BIT_ADDR | FLASH_FLAG_RESET), 70, + stfsm_mx25_config}, + +#define N25Q_FLAG (FLASH_FLAG_READ_WRITE | \ + FLASH_FLAG_READ_FAST | \ + FLASH_FLAG_READ_1_1_2 | \ + FLASH_FLAG_READ_1_2_2 | \ + FLASH_FLAG_READ_1_1_4 | \ + FLASH_FLAG_READ_1_4_4 | \ + FLASH_FLAG_WRITE_1_1_2 | \ + FLASH_FLAG_WRITE_1_2_2 | \ + FLASH_FLAG_WRITE_1_1_4 | \ + FLASH_FLAG_WRITE_1_4_4) + { "n25q128", 0x20ba18, 0, 64 * 1024, 256, N25Q_FLAG, 108, + stfsm_n25q_config }, + { "n25q256", 0x20ba19, 0, 64 * 1024, 512, + N25Q_FLAG | FLASH_FLAG_32BIT_ADDR, 108, stfsm_n25q_config }, + + /* + * Spansion S25FLxxxP + * - 256KiB and 64KiB sector variants (identified by ext. JEDEC) + */ +#define S25FLXXXP_FLAG (FLASH_FLAG_READ_WRITE | \ + FLASH_FLAG_READ_1_1_2 | \ + FLASH_FLAG_READ_1_2_2 | \ + FLASH_FLAG_READ_1_1_4 | \ + FLASH_FLAG_READ_1_4_4 | \ + FLASH_FLAG_WRITE_1_1_4 | \ + FLASH_FLAG_READ_FAST) + { "s25fl032p", 0x010215, 0x4d00, 64 * 1024, 64, S25FLXXXP_FLAG, 80, + stfsm_s25fl_config}, + { "s25fl129p0", 0x012018, 0x4d00, 256 * 1024, 64, S25FLXXXP_FLAG, 80, + stfsm_s25fl_config }, + { "s25fl129p1", 0x012018, 0x4d01, 64 * 1024, 256, S25FLXXXP_FLAG, 80, + stfsm_s25fl_config }, + + /* + * Spansion S25FLxxxS + * - 256KiB and 64KiB sector variants (identified by ext. JEDEC) + * - RESET# signal supported by die but not bristled out on all + * package types. The package type is a function of board design, + * so this information is captured in the board's flags. + * - Supports 'DYB' sector protection. Depending on variant, sectors + * may default to locked state on power-on. + */ +#define S25FLXXXS_FLAG (S25FLXXXP_FLAG | \ + FLASH_FLAG_RESET | \ + FLASH_FLAG_DYB_LOCKING) + { "s25fl128s0", 0x012018, 0x0300, 256 * 1024, 64, S25FLXXXS_FLAG, 80, + stfsm_s25fl_config }, + { "s25fl128s1", 0x012018, 0x0301, 64 * 1024, 256, S25FLXXXS_FLAG, 80, + stfsm_s25fl_config }, + { "s25fl256s0", 0x010219, 0x4d00, 256 * 1024, 128, + S25FLXXXS_FLAG | FLASH_FLAG_32BIT_ADDR, 80, stfsm_s25fl_config }, + { "s25fl256s1", 0x010219, 0x4d01, 64 * 1024, 512, + S25FLXXXS_FLAG | FLASH_FLAG_32BIT_ADDR, 80, stfsm_s25fl_config }, + + /* Winbond -- w25x "blocks" are 64K, "sectors" are 4KiB */ +#define W25X_FLAG (FLASH_FLAG_READ_WRITE | \ + FLASH_FLAG_READ_FAST | \ + FLASH_FLAG_READ_1_1_2 | \ + FLASH_FLAG_WRITE_1_1_2) + { "w25x40", 0xef3013, 0, 64 * 1024, 8, W25X_FLAG, 75, NULL }, + { "w25x80", 0xef3014, 0, 64 * 1024, 16, W25X_FLAG, 75, NULL }, + { "w25x16", 0xef3015, 0, 64 * 1024, 32, W25X_FLAG, 75, NULL }, + { "w25x32", 0xef3016, 0, 64 * 1024, 64, W25X_FLAG, 75, NULL }, + { "w25x64", 0xef3017, 0, 64 * 1024, 128, W25X_FLAG, 75, NULL }, + + /* Winbond -- w25q "blocks" are 64K, "sectors" are 4KiB */ +#define W25Q_FLAG (FLASH_FLAG_READ_WRITE | \ + FLASH_FLAG_READ_FAST | \ + FLASH_FLAG_READ_1_1_2 | \ + FLASH_FLAG_READ_1_2_2 | \ + FLASH_FLAG_READ_1_1_4 | \ + FLASH_FLAG_READ_1_4_4 | \ + FLASH_FLAG_WRITE_1_1_4) + { "w25q80", 0xef4014, 0, 64 * 1024, 16, W25Q_FLAG, 80, + stfsm_w25q_config }, + { "w25q16", 0xef4015, 0, 64 * 1024, 32, W25Q_FLAG, 80, + stfsm_w25q_config }, + { "w25q32", 0xef4016, 0, 64 * 1024, 64, W25Q_FLAG, 80, + stfsm_w25q_config }, + { "w25q64", 0xef4017, 0, 64 * 1024, 128, W25Q_FLAG, 80, + stfsm_w25q_config }, + + /* Sentinel */ + { NULL, 0x000000, 0, 0, 0, 0, 0, NULL }, +}; + +/* + * FSM message sequence configurations: + * + * All configs are presented in order of preference + */ + +/* Default READ configurations, in order of preference */ +static struct seq_rw_config default_read_configs[] = { + {FLASH_FLAG_READ_1_4_4, SPINOR_OP_READ_1_4_4, 0, 4, 4, 0x00, 2, 4}, + {FLASH_FLAG_READ_1_1_4, SPINOR_OP_READ_1_1_4, 0, 1, 4, 0x00, 4, 0}, + {FLASH_FLAG_READ_1_2_2, SPINOR_OP_READ_1_2_2, 0, 2, 2, 0x00, 4, 0}, + {FLASH_FLAG_READ_1_1_2, SPINOR_OP_READ_1_1_2, 0, 1, 2, 0x00, 0, 8}, + {FLASH_FLAG_READ_FAST, SPINOR_OP_READ_FAST, 0, 1, 1, 0x00, 0, 8}, + {FLASH_FLAG_READ_WRITE, SPINOR_OP_READ, 0, 1, 1, 0x00, 0, 0}, + {0x00, 0, 0, 0, 0, 0x00, 0, 0}, +}; + +/* Default WRITE configurations */ +static struct seq_rw_config default_write_configs[] = { + {FLASH_FLAG_WRITE_1_4_4, SPINOR_OP_WRITE_1_4_4, 1, 4, 4, 0x00, 0, 0}, + {FLASH_FLAG_WRITE_1_1_4, SPINOR_OP_WRITE_1_1_4, 1, 1, 4, 0x00, 0, 0}, + {FLASH_FLAG_WRITE_1_2_2, SPINOR_OP_WRITE_1_2_2, 1, 2, 2, 0x00, 0, 0}, + {FLASH_FLAG_WRITE_1_1_2, SPINOR_OP_WRITE_1_1_2, 1, 1, 2, 0x00, 0, 0}, + {FLASH_FLAG_READ_WRITE, SPINOR_OP_WRITE, 1, 1, 1, 0x00, 0, 0}, + {0x00, 0, 0, 0, 0, 0x00, 0, 0}, +}; + +/* + * [N25Qxxx] Configuration + */ +#define N25Q_VCR_DUMMY_CYCLES(x) (((x) & 0xf) << 4) +#define N25Q_VCR_XIP_DISABLED ((uint8_t)0x1 << 3) +#define N25Q_VCR_WRAP_CONT 0x3 + +/* N25Q 3-byte Address READ configurations + * - 'FAST' variants configured for 8 dummy cycles. + * + * Note, the number of dummy cycles used for 'FAST' READ operations is + * configurable and would normally be tuned according to the READ command and + * operating frequency. However, this applies universally to all 'FAST' READ + * commands, including those used by the SPIBoot controller, and remains in + * force until the device is power-cycled. Since the SPIBoot controller is + * hard-wired to use 8 dummy cycles, we must configure the device to also use 8 + * cycles. + */ +static struct seq_rw_config n25q_read3_configs[] = { + {FLASH_FLAG_READ_1_4_4, SPINOR_OP_READ_1_4_4, 0, 4, 4, 0x00, 0, 8}, + {FLASH_FLAG_READ_1_1_4, SPINOR_OP_READ_1_1_4, 0, 1, 4, 0x00, 0, 8}, + {FLASH_FLAG_READ_1_2_2, SPINOR_OP_READ_1_2_2, 0, 2, 2, 0x00, 0, 8}, + {FLASH_FLAG_READ_1_1_2, SPINOR_OP_READ_1_1_2, 0, 1, 2, 0x00, 0, 8}, + {FLASH_FLAG_READ_FAST, SPINOR_OP_READ_FAST, 0, 1, 1, 0x00, 0, 8}, + {FLASH_FLAG_READ_WRITE, SPINOR_OP_READ, 0, 1, 1, 0x00, 0, 0}, + {0x00, 0, 0, 0, 0, 0x00, 0, 0}, +}; + +/* N25Q 4-byte Address READ configurations + * - use special 4-byte address READ commands (reduces overheads, and + * reduces risk of hitting watchdog reset issues). + * - 'FAST' variants configured for 8 dummy cycles (see note above.) + */ +static struct seq_rw_config n25q_read4_configs[] = { + {FLASH_FLAG_READ_1_4_4, SPINOR_OP_READ4_1_4_4, 0, 4, 4, 0x00, 0, 8}, + {FLASH_FLAG_READ_1_1_4, SPINOR_OP_READ4_1_1_4, 0, 1, 4, 0x00, 0, 8}, + {FLASH_FLAG_READ_1_2_2, SPINOR_OP_READ4_1_2_2, 0, 2, 2, 0x00, 0, 8}, + {FLASH_FLAG_READ_1_1_2, SPINOR_OP_READ4_1_1_2, 0, 1, 2, 0x00, 0, 8}, + {FLASH_FLAG_READ_FAST, SPINOR_OP_READ4_FAST, 0, 1, 1, 0x00, 0, 8}, + {FLASH_FLAG_READ_WRITE, SPINOR_OP_READ4, 0, 1, 1, 0x00, 0, 0}, + {0x00, 0, 0, 0, 0, 0x00, 0, 0}, +}; + +/* + * [MX25xxx] Configuration + */ +#define MX25_STATUS_QE (0x1 << 6) + +static int stfsm_mx25_en_32bit_addr_seq(struct stfsm_seq *seq) +{ + seq->seq_opc[0] = (SEQ_OPC_PADS_1 | + SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(SPINOR_OP_EN4B) | + SEQ_OPC_CSDEASSERT); + + seq->seq[0] = STFSM_INST_CMD1; + seq->seq[1] = STFSM_INST_WAIT; + seq->seq[2] = STFSM_INST_STOP; + + seq->seq_cfg = (SEQ_CFG_PADS_1 | + SEQ_CFG_ERASE | + SEQ_CFG_READNOTWRITE | + SEQ_CFG_CSDEASSERT | + SEQ_CFG_STARTSEQ); + + return 0; +} + +/* + * [S25FLxxx] Configuration + */ +#define STFSM_S25FL_CONFIG_QE (0x1 << 1) + +/* + * S25FLxxxS devices provide three ways of supporting 32-bit addressing: Bank + * Register, Extended Address Modes, and a 32-bit address command set. The + * 32-bit address command set is used here, since it avoids any problems with + * entering a state that is incompatible with the SPIBoot Controller. + */ +static struct seq_rw_config stfsm_s25fl_read4_configs[] = { + {FLASH_FLAG_READ_1_4_4, SPINOR_OP_READ4_1_4_4, 0, 4, 4, 0x00, 2, 4}, + {FLASH_FLAG_READ_1_1_4, SPINOR_OP_READ4_1_1_4, 0, 1, 4, 0x00, 0, 8}, + {FLASH_FLAG_READ_1_2_2, SPINOR_OP_READ4_1_2_2, 0, 2, 2, 0x00, 4, 0}, + {FLASH_FLAG_READ_1_1_2, SPINOR_OP_READ4_1_1_2, 0, 1, 2, 0x00, 0, 8}, + {FLASH_FLAG_READ_FAST, SPINOR_OP_READ4_FAST, 0, 1, 1, 0x00, 0, 8}, + {FLASH_FLAG_READ_WRITE, SPINOR_OP_READ4, 0, 1, 1, 0x00, 0, 0}, + {0x00, 0, 0, 0, 0, 0x00, 0, 0}, +}; + +static struct seq_rw_config stfsm_s25fl_write4_configs[] = { + {FLASH_FLAG_WRITE_1_1_4, S25FL_CMD_WRITE4_1_1_4, 1, 1, 4, 0x00, 0, 0}, + {FLASH_FLAG_READ_WRITE, S25FL_CMD_WRITE4, 1, 1, 1, 0x00, 0, 0}, + {0x00, 0, 0, 0, 0, 0x00, 0, 0}, +}; + +/* + * [W25Qxxx] Configuration + */ +#define W25Q_STATUS_QE (0x1 << 1) + +static struct stfsm_seq stfsm_seq_read_jedec = { + .data_size = TRANSFER_SIZE(8), + .seq_opc[0] = (SEQ_OPC_PADS_1 | + SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(SPINOR_OP_RDID)), + .seq = { + STFSM_INST_CMD1, + STFSM_INST_DATA_READ, + STFSM_INST_STOP, + }, + .seq_cfg = (SEQ_CFG_PADS_1 | + SEQ_CFG_READNOTWRITE | + SEQ_CFG_CSDEASSERT | + SEQ_CFG_STARTSEQ), +}; + +static struct stfsm_seq stfsm_seq_read_status_fifo = { + .data_size = TRANSFER_SIZE(4), + .seq_opc[0] = (SEQ_OPC_PADS_1 | + SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(SPINOR_OP_RDSR)), + .seq = { + STFSM_INST_CMD1, + STFSM_INST_DATA_READ, + STFSM_INST_STOP, + }, + .seq_cfg = (SEQ_CFG_PADS_1 | + SEQ_CFG_READNOTWRITE | + SEQ_CFG_CSDEASSERT | + SEQ_CFG_STARTSEQ), +}; + +static struct stfsm_seq stfsm_seq_erase_sector = { + /* 'addr_cfg' configured during initialisation */ + .seq_opc = { + (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(SPINOR_OP_WREN) | SEQ_OPC_CSDEASSERT), + + (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(SPINOR_OP_SE)), + }, + .seq = { + STFSM_INST_CMD1, + STFSM_INST_CMD2, + STFSM_INST_ADD1, + STFSM_INST_ADD2, + STFSM_INST_STOP, + }, + .seq_cfg = (SEQ_CFG_PADS_1 | + SEQ_CFG_READNOTWRITE | + SEQ_CFG_CSDEASSERT | + SEQ_CFG_STARTSEQ), +}; + +static struct stfsm_seq stfsm_seq_erase_chip = { + .seq_opc = { + (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(SPINOR_OP_WREN) | SEQ_OPC_CSDEASSERT), + + (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(SPINOR_OP_CHIP_ERASE) | SEQ_OPC_CSDEASSERT), + }, + .seq = { + STFSM_INST_CMD1, + STFSM_INST_CMD2, + STFSM_INST_WAIT, + STFSM_INST_STOP, + }, + .seq_cfg = (SEQ_CFG_PADS_1 | + SEQ_CFG_ERASE | + SEQ_CFG_READNOTWRITE | + SEQ_CFG_CSDEASSERT | + SEQ_CFG_STARTSEQ), +}; + +static struct stfsm_seq stfsm_seq_write_status = { + .seq_opc[0] = (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(SPINOR_OP_WREN) | SEQ_OPC_CSDEASSERT), + .seq_opc[1] = (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(SPINOR_OP_WRSR)), + .seq = { + STFSM_INST_CMD1, + STFSM_INST_CMD2, + STFSM_INST_STA_WR1, + STFSM_INST_STOP, + }, + .seq_cfg = (SEQ_CFG_PADS_1 | + SEQ_CFG_READNOTWRITE | + SEQ_CFG_CSDEASSERT | + SEQ_CFG_STARTSEQ), +}; + +static int stfsm_n25q_en_32bit_addr_seq(struct stfsm_seq *seq) +{ + seq->seq_opc[0] = (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(SPINOR_OP_EN4B)); + seq->seq_opc[1] = (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(SPINOR_OP_WREN) | + SEQ_OPC_CSDEASSERT); + + seq->seq[0] = STFSM_INST_CMD2; + seq->seq[1] = STFSM_INST_CMD1; + seq->seq[2] = STFSM_INST_WAIT; + seq->seq[3] = STFSM_INST_STOP; + + seq->seq_cfg = (SEQ_CFG_PADS_1 | + SEQ_CFG_ERASE | + SEQ_CFG_READNOTWRITE | + SEQ_CFG_CSDEASSERT | + SEQ_CFG_STARTSEQ); + + return 0; +} + +static inline int stfsm_is_idle(struct stfsm *fsm) +{ + return readl(fsm->base + SPI_FAST_SEQ_STA) & 0x10; +} + +static inline uint32_t stfsm_fifo_available(struct stfsm *fsm) +{ + return (readl(fsm->base + SPI_FAST_SEQ_STA) >> 5) & 0x7f; +} + +static void stfsm_clear_fifo(struct stfsm *fsm) +{ + uint32_t avail; + + for (;;) { + avail = stfsm_fifo_available(fsm); + if (!avail) + break; + + while (avail) { + readl(fsm->base + SPI_FAST_SEQ_DATA_REG); + avail--; + } + } +} + +static inline void stfsm_load_seq(struct stfsm *fsm, + const struct stfsm_seq *seq) +{ + void __iomem *dst = fsm->base + SPI_FAST_SEQ_TRANSFER_SIZE; + const uint32_t *src = (const uint32_t *)seq; + int words = sizeof(*seq) / sizeof(*src); + + BUG_ON(!stfsm_is_idle(fsm)); + + while (words--) { + writel(*src, dst); + src++; + dst += 4; + } +} + +static void stfsm_wait_seq(struct stfsm *fsm) +{ + unsigned long deadline; + int timeout = 0; + + deadline = jiffies + msecs_to_jiffies(STFSM_MAX_WAIT_SEQ_MS); + + while (!timeout) { + if (time_after_eq(jiffies, deadline)) + timeout = 1; + + if (stfsm_is_idle(fsm)) + return; + + cond_resched(); + } + + dev_err(fsm->dev, "timeout on sequence completion\n"); +} + +static void stfsm_read_fifo(struct stfsm *fsm, uint32_t *buf, uint32_t size) +{ + uint32_t remaining = size >> 2; + uint32_t avail; + uint32_t words; + + dev_dbg(fsm->dev, "Reading %d bytes from FIFO\n", size); + + BUG_ON((((uintptr_t)buf) & 0x3) || (size & 0x3)); + + while (remaining) { + for (;;) { + avail = stfsm_fifo_available(fsm); + if (avail) + break; + udelay(1); + } + words = min(avail, remaining); + remaining -= words; + + readsl(fsm->base + SPI_FAST_SEQ_DATA_REG, buf, words); + buf += words; + } +} + +static int stfsm_write_fifo(struct stfsm *fsm, const uint32_t *buf, + uint32_t size) +{ + uint32_t words = size >> 2; + + dev_dbg(fsm->dev, "writing %d bytes to FIFO\n", size); + + BUG_ON((((uintptr_t)buf) & 0x3) || (size & 0x3)); + + writesl(fsm->base + SPI_FAST_SEQ_DATA_REG, buf, words); + + return size; +} + +static int stfsm_enter_32bit_addr(struct stfsm *fsm, int enter) +{ + struct stfsm_seq *seq = &fsm->stfsm_seq_en_32bit_addr; + uint32_t cmd = enter ? SPINOR_OP_EN4B : SPINOR_OP_EX4B; + + seq->seq_opc[0] = (SEQ_OPC_PADS_1 | + SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(cmd) | + SEQ_OPC_CSDEASSERT); + + stfsm_load_seq(fsm, seq); + + stfsm_wait_seq(fsm); + + return 0; +} + +static uint8_t stfsm_wait_busy(struct stfsm *fsm) +{ + struct stfsm_seq *seq = &stfsm_seq_read_status_fifo; + unsigned long deadline; + uint32_t status; + int timeout = 0; + + /* Use RDRS1 */ + seq->seq_opc[0] = (SEQ_OPC_PADS_1 | + SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(SPINOR_OP_RDSR)); + + /* Load read_status sequence */ + stfsm_load_seq(fsm, seq); + + /* + * Repeat until busy bit is deasserted, or timeout, or error (S25FLxxxS) + */ + deadline = jiffies + FLASH_MAX_BUSY_WAIT; + while (!timeout) { + if (time_after_eq(jiffies, deadline)) + timeout = 1; + + stfsm_wait_seq(fsm); + + stfsm_read_fifo(fsm, &status, 4); + + if ((status & FLASH_STATUS_BUSY) == 0) + return 0; + + if ((fsm->configuration & CFG_S25FL_CHECK_ERROR_FLAGS) && + ((status & S25FL_STATUS_P_ERR) || + (status & S25FL_STATUS_E_ERR))) + return (uint8_t)(status & 0xff); + + if (!timeout) + /* Restart */ + writel(seq->seq_cfg, fsm->base + SPI_FAST_SEQ_CFG); + + cond_resched(); + } + + dev_err(fsm->dev, "timeout on wait_busy\n"); + + return FLASH_STATUS_TIMEOUT; +} + +static int stfsm_read_status(struct stfsm *fsm, uint8_t cmd, + uint8_t *data, int bytes) +{ + struct stfsm_seq *seq = &stfsm_seq_read_status_fifo; + uint32_t tmp; + uint8_t *t = (uint8_t *)&tmp; + int i; + + dev_dbg(fsm->dev, "read 'status' register [0x%02x], %d byte(s)\n", + cmd, bytes); + + BUG_ON(bytes != 1 && bytes != 2); + + seq->seq_opc[0] = (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(cmd)), + + stfsm_load_seq(fsm, seq); + + stfsm_read_fifo(fsm, &tmp, 4); + + for (i = 0; i < bytes; i++) + data[i] = t[i]; + + stfsm_wait_seq(fsm); + + return 0; +} + +static int stfsm_write_status(struct stfsm *fsm, uint8_t cmd, + uint16_t data, int bytes, int wait_busy) +{ + struct stfsm_seq *seq = &stfsm_seq_write_status; + + dev_dbg(fsm->dev, + "write 'status' register [0x%02x], %d byte(s), 0x%04x\n" + " %s wait-busy\n", cmd, bytes, data, wait_busy ? "with" : "no"); + + BUG_ON(bytes != 1 && bytes != 2); + + seq->seq_opc[1] = (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(cmd)); + + seq->status = (uint32_t)data | STA_PADS_1 | STA_CSDEASSERT; + seq->seq[2] = (bytes == 1) ? STFSM_INST_STA_WR1 : STFSM_INST_STA_WR1_2; + + stfsm_load_seq(fsm, seq); + + stfsm_wait_seq(fsm); + + if (wait_busy) + stfsm_wait_busy(fsm); + + return 0; +} + +/* + * SoC reset on 'boot-from-spi' systems + * + * Certain modes of operation cause the Flash device to enter a particular state + * for a period of time (e.g. 'Erase Sector', 'Quad Enable', and 'Enter 32-bit + * Addr' commands). On boot-from-spi systems, it is important to consider what + * happens if a warm reset occurs during this period. The SPIBoot controller + * assumes that Flash device is in its default reset state, 24-bit address mode, + * and ready to accept commands. This can be achieved using some form of + * on-board logic/controller to force a device POR in response to a SoC-level + * reset or by making use of the device reset signal if available (limited + * number of devices only). + * + * Failure to take such precautions can cause problems following a warm reset. + * For some operations (e.g. ERASE), there is little that can be done. For + * other modes of operation (e.g. 32-bit addressing), options are often + * available that can help minimise the window in which a reset could cause a + * problem. + * + */ +static bool stfsm_can_handle_soc_reset(struct stfsm *fsm) +{ + /* Reset signal is available on the board and supported by the device */ + if (fsm->reset_signal && fsm->info->flags & FLASH_FLAG_RESET) + return true; + + /* Board-level logic forces a power-on-reset */ + if (fsm->reset_por) + return true; + + /* Reset is not properly handled and may result in failure to reboot */ + return false; +} + +/* Configure 'addr_cfg' according to addressing mode */ +static void stfsm_prepare_erasesec_seq(struct stfsm *fsm, + struct stfsm_seq *seq) +{ + int addr1_cycles = fsm->info->flags & FLASH_FLAG_32BIT_ADDR ? 16 : 8; + + seq->addr_cfg = (ADR_CFG_CYCLES_ADD1(addr1_cycles) | + ADR_CFG_PADS_1_ADD1 | + ADR_CFG_CYCLES_ADD2(16) | + ADR_CFG_PADS_1_ADD2 | + ADR_CFG_CSDEASSERT_ADD2); +} + +/* Search for preferred configuration based on available flags */ +static struct seq_rw_config * +stfsm_search_seq_rw_configs(struct stfsm *fsm, + struct seq_rw_config cfgs[]) +{ + struct seq_rw_config *config; + int flags = fsm->info->flags; + + for (config = cfgs; config->cmd != 0; config++) + if ((config->flags & flags) == config->flags) + return config; + + return NULL; +} + +/* Prepare a READ/WRITE sequence according to configuration parameters */ +static void stfsm_prepare_rw_seq(struct stfsm *fsm, + struct stfsm_seq *seq, + struct seq_rw_config *cfg) +{ + int addr1_cycles, addr2_cycles; + int i = 0; + + memset(seq, 0, sizeof(*seq)); + + /* Add READ/WRITE OPC */ + seq->seq_opc[i++] = (SEQ_OPC_PADS_1 | + SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(cfg->cmd)); + + /* Add WREN OPC for a WRITE sequence */ + if (cfg->write) + seq->seq_opc[i++] = (SEQ_OPC_PADS_1 | + SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(SPINOR_OP_WREN) | + SEQ_OPC_CSDEASSERT); + + /* Address configuration (24 or 32-bit addresses) */ + addr1_cycles = (fsm->info->flags & FLASH_FLAG_32BIT_ADDR) ? 16 : 8; + addr1_cycles /= cfg->addr_pads; + addr2_cycles = 16 / cfg->addr_pads; + seq->addr_cfg = ((addr1_cycles & 0x3f) << 0 | /* ADD1 cycles */ + (cfg->addr_pads - 1) << 6 | /* ADD1 pads */ + (addr2_cycles & 0x3f) << 16 | /* ADD2 cycles */ + ((cfg->addr_pads - 1) << 22)); /* ADD2 pads */ + + /* Data/Sequence configuration */ + seq->seq_cfg = ((cfg->data_pads - 1) << 16 | + SEQ_CFG_STARTSEQ | + SEQ_CFG_CSDEASSERT); + if (!cfg->write) + seq->seq_cfg |= SEQ_CFG_READNOTWRITE; + + /* Mode configuration (no. of pads taken from addr cfg) */ + seq->mode = ((cfg->mode_data & 0xff) << 0 | /* data */ + (cfg->mode_cycles & 0x3f) << 16 | /* cycles */ + (cfg->addr_pads - 1) << 22); /* pads */ + + /* Dummy configuration (no. of pads taken from addr cfg) */ + seq->dummy = ((cfg->dummy_cycles & 0x3f) << 16 | /* cycles */ + (cfg->addr_pads - 1) << 22); /* pads */ + + + /* Instruction sequence */ + i = 0; + if (cfg->write) + seq->seq[i++] = STFSM_INST_CMD2; + + seq->seq[i++] = STFSM_INST_CMD1; + + seq->seq[i++] = STFSM_INST_ADD1; + seq->seq[i++] = STFSM_INST_ADD2; + + if (cfg->mode_cycles) + seq->seq[i++] = STFSM_INST_MODE; + + if (cfg->dummy_cycles) + seq->seq[i++] = STFSM_INST_DUMMY; + + seq->seq[i++] = + cfg->write ? STFSM_INST_DATA_WRITE : STFSM_INST_DATA_READ; + seq->seq[i++] = STFSM_INST_STOP; +} + +static int stfsm_search_prepare_rw_seq(struct stfsm *fsm, + struct stfsm_seq *seq, + struct seq_rw_config *cfgs) +{ + struct seq_rw_config *config; + + config = stfsm_search_seq_rw_configs(fsm, cfgs); + if (!config) { + dev_err(fsm->dev, "failed to find suitable config\n"); + return -EINVAL; + } + + stfsm_prepare_rw_seq(fsm, seq, config); + + return 0; +} + +/* Prepare a READ/WRITE/ERASE 'default' sequences */ +static int stfsm_prepare_rwe_seqs_default(struct stfsm *fsm) +{ + uint32_t flags = fsm->info->flags; + int ret; + + /* Configure 'READ' sequence */ + ret = stfsm_search_prepare_rw_seq(fsm, &fsm->stfsm_seq_read, + default_read_configs); + if (ret) { + dev_err(fsm->dev, + "failed to prep READ sequence with flags [0x%08x]\n", + flags); + return ret; + } + + /* Configure 'WRITE' sequence */ + ret = stfsm_search_prepare_rw_seq(fsm, &fsm->stfsm_seq_write, + default_write_configs); + if (ret) { + dev_err(fsm->dev, + "failed to prep WRITE sequence with flags [0x%08x]\n", + flags); + return ret; + } + + /* Configure 'ERASE_SECTOR' sequence */ + stfsm_prepare_erasesec_seq(fsm, &stfsm_seq_erase_sector); + + return 0; +} + +static int stfsm_mx25_config(struct stfsm *fsm) +{ + uint32_t flags = fsm->info->flags; + uint32_t data_pads; + uint8_t sta; + int ret; + bool soc_reset; + + /* + * Use default READ/WRITE sequences + */ + ret = stfsm_prepare_rwe_seqs_default(fsm); + if (ret) + return ret; + + /* + * Configure 32-bit Address Support + */ + if (flags & FLASH_FLAG_32BIT_ADDR) { + /* Configure 'enter_32bitaddr' FSM sequence */ + stfsm_mx25_en_32bit_addr_seq(&fsm->stfsm_seq_en_32bit_addr); + + soc_reset = stfsm_can_handle_soc_reset(fsm); + if (soc_reset || !fsm->booted_from_spi) + /* If we can handle SoC resets, we enable 32-bit address + * mode pervasively */ + stfsm_enter_32bit_addr(fsm, 1); + + else + /* Else, enable/disable 32-bit addressing before/after + * each operation */ + fsm->configuration = (CFG_READ_TOGGLE_32BIT_ADDR | + CFG_WRITE_TOGGLE_32BIT_ADDR | + CFG_ERASESEC_TOGGLE_32BIT_ADDR); + } + + /* Check status of 'QE' bit, update if required. */ + stfsm_read_status(fsm, SPINOR_OP_RDSR, &sta, 1); + data_pads = ((fsm->stfsm_seq_read.seq_cfg >> 16) & 0x3) + 1; + if (data_pads == 4) { + if (!(sta & MX25_STATUS_QE)) { + /* Set 'QE' */ + sta |= MX25_STATUS_QE; + + stfsm_write_status(fsm, SPINOR_OP_WRSR, sta, 1, 1); + } + } else { + if (sta & MX25_STATUS_QE) { + /* Clear 'QE' */ + sta &= ~MX25_STATUS_QE; + + stfsm_write_status(fsm, SPINOR_OP_WRSR, sta, 1, 1); + } + } + + return 0; +} + +static int stfsm_n25q_config(struct stfsm *fsm) +{ + uint32_t flags = fsm->info->flags; + uint8_t vcr; + int ret = 0; + bool soc_reset; + + /* Configure 'READ' sequence */ + if (flags & FLASH_FLAG_32BIT_ADDR) + ret = stfsm_search_prepare_rw_seq(fsm, &fsm->stfsm_seq_read, + n25q_read4_configs); + else + ret = stfsm_search_prepare_rw_seq(fsm, &fsm->stfsm_seq_read, + n25q_read3_configs); + if (ret) { + dev_err(fsm->dev, + "failed to prepare READ sequence with flags [0x%08x]\n", + flags); + return ret; + } + + /* Configure 'WRITE' sequence (default configs) */ + ret = stfsm_search_prepare_rw_seq(fsm, &fsm->stfsm_seq_write, + default_write_configs); + if (ret) { + dev_err(fsm->dev, + "preparing WRITE sequence using flags [0x%08x] failed\n", + flags); + return ret; + } + + /* * Configure 'ERASE_SECTOR' sequence */ + stfsm_prepare_erasesec_seq(fsm, &stfsm_seq_erase_sector); + + /* Configure 32-bit address support */ + if (flags & FLASH_FLAG_32BIT_ADDR) { + stfsm_n25q_en_32bit_addr_seq(&fsm->stfsm_seq_en_32bit_addr); + + soc_reset = stfsm_can_handle_soc_reset(fsm); + if (soc_reset || !fsm->booted_from_spi) { + /* + * If we can handle SoC resets, we enable 32-bit + * address mode pervasively + */ + stfsm_enter_32bit_addr(fsm, 1); + } else { + /* + * If not, enable/disable for WRITE and ERASE + * operations (READ uses special commands) + */ + fsm->configuration = (CFG_WRITE_TOGGLE_32BIT_ADDR | + CFG_ERASESEC_TOGGLE_32BIT_ADDR); + } + } + + /* + * Configure device to use 8 dummy cycles + */ + vcr = (N25Q_VCR_DUMMY_CYCLES(8) | N25Q_VCR_XIP_DISABLED | + N25Q_VCR_WRAP_CONT); + stfsm_write_status(fsm, N25Q_CMD_WRVCR, vcr, 1, 0); + + return 0; +} + +static void stfsm_s25fl_prepare_erasesec_seq_32(struct stfsm_seq *seq) +{ + seq->seq_opc[1] = (SEQ_OPC_PADS_1 | + SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(S25FL_CMD_SE4)); + + seq->addr_cfg = (ADR_CFG_CYCLES_ADD1(16) | + ADR_CFG_PADS_1_ADD1 | + ADR_CFG_CYCLES_ADD2(16) | + ADR_CFG_PADS_1_ADD2 | + ADR_CFG_CSDEASSERT_ADD2); +} + +static void stfsm_s25fl_read_dyb(struct stfsm *fsm, uint32_t offs, uint8_t *dby) +{ + uint32_t tmp; + struct stfsm_seq seq = { + .data_size = TRANSFER_SIZE(4), + .seq_opc[0] = (SEQ_OPC_PADS_1 | + SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(S25FL_CMD_DYBRD)), + .addr_cfg = (ADR_CFG_CYCLES_ADD1(16) | + ADR_CFG_PADS_1_ADD1 | + ADR_CFG_CYCLES_ADD2(16) | + ADR_CFG_PADS_1_ADD2), + .addr1 = (offs >> 16) & 0xffff, + .addr2 = offs & 0xffff, + .seq = { + STFSM_INST_CMD1, + STFSM_INST_ADD1, + STFSM_INST_ADD2, + STFSM_INST_DATA_READ, + STFSM_INST_STOP, + }, + .seq_cfg = (SEQ_CFG_PADS_1 | + SEQ_CFG_READNOTWRITE | + SEQ_CFG_CSDEASSERT | + SEQ_CFG_STARTSEQ), + }; + + stfsm_load_seq(fsm, &seq); + + stfsm_read_fifo(fsm, &tmp, 4); + + *dby = (uint8_t)(tmp >> 24); + + stfsm_wait_seq(fsm); +} + +static void stfsm_s25fl_write_dyb(struct stfsm *fsm, uint32_t offs, uint8_t dby) +{ + struct stfsm_seq seq = { + .seq_opc[0] = (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(SPINOR_OP_WREN) | + SEQ_OPC_CSDEASSERT), + .seq_opc[1] = (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(S25FL_CMD_DYBWR)), + .addr_cfg = (ADR_CFG_CYCLES_ADD1(16) | + ADR_CFG_PADS_1_ADD1 | + ADR_CFG_CYCLES_ADD2(16) | + ADR_CFG_PADS_1_ADD2), + .status = (uint32_t)dby | STA_PADS_1 | STA_CSDEASSERT, + .addr1 = (offs >> 16) & 0xffff, + .addr2 = offs & 0xffff, + .seq = { + STFSM_INST_CMD1, + STFSM_INST_CMD2, + STFSM_INST_ADD1, + STFSM_INST_ADD2, + STFSM_INST_STA_WR1, + STFSM_INST_STOP, + }, + .seq_cfg = (SEQ_CFG_PADS_1 | + SEQ_CFG_READNOTWRITE | + SEQ_CFG_CSDEASSERT | + SEQ_CFG_STARTSEQ), + }; + + stfsm_load_seq(fsm, &seq); + stfsm_wait_seq(fsm); + + stfsm_wait_busy(fsm); +} + +static int stfsm_s25fl_clear_status_reg(struct stfsm *fsm) +{ + struct stfsm_seq seq = { + .seq_opc[0] = (SEQ_OPC_PADS_1 | + SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(S25FL_CMD_CLSR) | + SEQ_OPC_CSDEASSERT), + .seq_opc[1] = (SEQ_OPC_PADS_1 | + SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(SPINOR_OP_WRDI) | + SEQ_OPC_CSDEASSERT), + .seq = { + STFSM_INST_CMD1, + STFSM_INST_CMD2, + STFSM_INST_WAIT, + STFSM_INST_STOP, + }, + .seq_cfg = (SEQ_CFG_PADS_1 | + SEQ_CFG_ERASE | + SEQ_CFG_READNOTWRITE | + SEQ_CFG_CSDEASSERT | + SEQ_CFG_STARTSEQ), + }; + + stfsm_load_seq(fsm, &seq); + + stfsm_wait_seq(fsm); + + return 0; +} + +static int stfsm_s25fl_config(struct stfsm *fsm) +{ + struct flash_info *info = fsm->info; + uint32_t flags = info->flags; + uint32_t data_pads; + uint32_t offs; + uint16_t sta_wr; + uint8_t sr1, cr1, dyb; + int update_sr = 0; + int ret; + + if (flags & FLASH_FLAG_32BIT_ADDR) { + /* + * Prepare Read/Write/Erase sequences according to S25FLxxx + * 32-bit address command set + */ + ret = stfsm_search_prepare_rw_seq(fsm, &fsm->stfsm_seq_read, + stfsm_s25fl_read4_configs); + if (ret) + return ret; + + ret = stfsm_search_prepare_rw_seq(fsm, &fsm->stfsm_seq_write, + stfsm_s25fl_write4_configs); + if (ret) + return ret; + + stfsm_s25fl_prepare_erasesec_seq_32(&stfsm_seq_erase_sector); + + } else { + /* Use default configurations for 24-bit addressing */ + ret = stfsm_prepare_rwe_seqs_default(fsm); + if (ret) + return ret; + } + + /* + * For devices that support 'DYB' sector locking, check lock status and + * unlock sectors if necessary (some variants power-on with sectors + * locked by default) + */ + if (flags & FLASH_FLAG_DYB_LOCKING) { + offs = 0; + for (offs = 0; offs < info->sector_size * info->n_sectors;) { + stfsm_s25fl_read_dyb(fsm, offs, &dyb); + if (dyb == 0x00) + stfsm_s25fl_write_dyb(fsm, offs, 0xff); + + /* Handle bottom/top 4KiB parameter sectors */ + if ((offs < info->sector_size * 2) || + (offs >= (info->sector_size - info->n_sectors * 4))) + offs += 0x1000; + else + offs += 0x10000; + } + } + + /* Check status of 'QE' bit, update if required. */ + stfsm_read_status(fsm, SPINOR_OP_RDSR2, &cr1, 1); + data_pads = ((fsm->stfsm_seq_read.seq_cfg >> 16) & 0x3) + 1; + if (data_pads == 4) { + if (!(cr1 & STFSM_S25FL_CONFIG_QE)) { + /* Set 'QE' */ + cr1 |= STFSM_S25FL_CONFIG_QE; + + update_sr = 1; + } + } else { + if (cr1 & STFSM_S25FL_CONFIG_QE) { + /* Clear 'QE' */ + cr1 &= ~STFSM_S25FL_CONFIG_QE; + + update_sr = 1; + } + } + if (update_sr) { + stfsm_read_status(fsm, SPINOR_OP_RDSR, &sr1, 1); + sta_wr = ((uint16_t)cr1 << 8) | sr1; + stfsm_write_status(fsm, SPINOR_OP_WRSR, sta_wr, 2, 1); + } + + /* + * S25FLxxx devices support Program and Error error flags. + * Configure driver to check flags and clear if necessary. + */ + fsm->configuration |= CFG_S25FL_CHECK_ERROR_FLAGS; + + return 0; +} + +static int stfsm_w25q_config(struct stfsm *fsm) +{ + uint32_t data_pads; + uint8_t sr1, sr2; + uint16_t sr_wr; + int update_sr = 0; + int ret; + + ret = stfsm_prepare_rwe_seqs_default(fsm); + if (ret) + return ret; + + /* Check status of 'QE' bit, update if required. */ + stfsm_read_status(fsm, SPINOR_OP_RDSR2, &sr2, 1); + data_pads = ((fsm->stfsm_seq_read.seq_cfg >> 16) & 0x3) + 1; + if (data_pads == 4) { + if (!(sr2 & W25Q_STATUS_QE)) { + /* Set 'QE' */ + sr2 |= W25Q_STATUS_QE; + update_sr = 1; + } + } else { + if (sr2 & W25Q_STATUS_QE) { + /* Clear 'QE' */ + sr2 &= ~W25Q_STATUS_QE; + update_sr = 1; + } + } + if (update_sr) { + /* Write status register */ + stfsm_read_status(fsm, SPINOR_OP_RDSR, &sr1, 1); + sr_wr = ((uint16_t)sr2 << 8) | sr1; + stfsm_write_status(fsm, SPINOR_OP_WRSR, sr_wr, 2, 1); + } + + return 0; +} + +static int stfsm_read(struct stfsm *fsm, uint8_t *buf, uint32_t size, + uint32_t offset) +{ + struct stfsm_seq *seq = &fsm->stfsm_seq_read; + uint32_t data_pads; + uint32_t read_mask; + uint32_t size_ub; + uint32_t size_lb; + uint32_t size_mop; + uint32_t tmp[4]; + uint32_t page_buf[FLASH_PAGESIZE_32]; + uint8_t *p; + + dev_dbg(fsm->dev, "reading %d bytes from 0x%08x\n", size, offset); + + /* Enter 32-bit address mode, if required */ + if (fsm->configuration & CFG_READ_TOGGLE_32BIT_ADDR) + stfsm_enter_32bit_addr(fsm, 1); + + /* Must read in multiples of 32 cycles (or 32*pads/8 Bytes) */ + data_pads = ((seq->seq_cfg >> 16) & 0x3) + 1; + read_mask = (data_pads << 2) - 1; + + /* Handle non-aligned buf */ + p = ((uintptr_t)buf & 0x3) ? (uint8_t *)page_buf : buf; + + /* Handle non-aligned size */ + size_ub = (size + read_mask) & ~read_mask; + size_lb = size & ~read_mask; + size_mop = size & read_mask; + + seq->data_size = TRANSFER_SIZE(size_ub); + seq->addr1 = (offset >> 16) & 0xffff; + seq->addr2 = offset & 0xffff; + + stfsm_load_seq(fsm, seq); + + if (size_lb) + stfsm_read_fifo(fsm, (uint32_t *)p, size_lb); + + if (size_mop) { + stfsm_read_fifo(fsm, tmp, read_mask + 1); + memcpy(p + size_lb, &tmp, size_mop); + } + + /* Handle non-aligned buf */ + if ((uintptr_t)buf & 0x3) + memcpy(buf, page_buf, size); + + /* Wait for sequence to finish */ + stfsm_wait_seq(fsm); + + stfsm_clear_fifo(fsm); + + /* Exit 32-bit address mode, if required */ + if (fsm->configuration & CFG_READ_TOGGLE_32BIT_ADDR) + stfsm_enter_32bit_addr(fsm, 0); + + return 0; +} + +static int stfsm_write(struct stfsm *fsm, const uint8_t *buf, + uint32_t size, uint32_t offset) +{ + struct stfsm_seq *seq = &fsm->stfsm_seq_write; + uint32_t data_pads; + uint32_t write_mask; + uint32_t size_ub; + uint32_t size_lb; + uint32_t size_mop; + uint32_t tmp[4]; + uint32_t page_buf[FLASH_PAGESIZE_32]; + uint8_t *t = (uint8_t *)&tmp; + const uint8_t *p; + int ret; + int i; + + dev_dbg(fsm->dev, "writing %d bytes to 0x%08x\n", size, offset); + + /* Enter 32-bit address mode, if required */ + if (fsm->configuration & CFG_WRITE_TOGGLE_32BIT_ADDR) + stfsm_enter_32bit_addr(fsm, 1); + + /* Must write in multiples of 32 cycles (or 32*pads/8 bytes) */ + data_pads = ((seq->seq_cfg >> 16) & 0x3) + 1; + write_mask = (data_pads << 2) - 1; + + /* Handle non-aligned buf */ + if ((uintptr_t)buf & 0x3) { + memcpy(page_buf, buf, size); + p = (uint8_t *)page_buf; + } else { + p = buf; + } + + /* Handle non-aligned size */ + size_ub = (size + write_mask) & ~write_mask; + size_lb = size & ~write_mask; + size_mop = size & write_mask; + + seq->data_size = TRANSFER_SIZE(size_ub); + seq->addr1 = (offset >> 16) & 0xffff; + seq->addr2 = offset & 0xffff; + + /* Need to set FIFO to write mode, before writing data to FIFO (see + * GNBvb79594) + */ + writel(0x00040000, fsm->base + SPI_FAST_SEQ_CFG); + + /* + * Before writing data to the FIFO, apply a small delay to allow a + * potential change of FIFO direction to complete. + */ + if (fsm->fifo_dir_delay == 0) + readl(fsm->base + SPI_FAST_SEQ_CFG); + else + udelay(fsm->fifo_dir_delay); + + + /* Write data to FIFO, before starting sequence (see GNBvd79593) */ + if (size_lb) { + stfsm_write_fifo(fsm, (uint32_t *)p, size_lb); + p += size_lb; + } + + /* Handle non-aligned size */ + if (size_mop) { + memset(t, 0xff, write_mask + 1); /* fill with 0xff's */ + for (i = 0; i < size_mop; i++) + t[i] = *p++; + + stfsm_write_fifo(fsm, tmp, write_mask + 1); + } + + /* Start sequence */ + stfsm_load_seq(fsm, seq); + + /* Wait for sequence to finish */ + stfsm_wait_seq(fsm); + + /* Wait for completion */ + ret = stfsm_wait_busy(fsm); + if (ret && fsm->configuration & CFG_S25FL_CHECK_ERROR_FLAGS) + stfsm_s25fl_clear_status_reg(fsm); + + /* Exit 32-bit address mode, if required */ + if (fsm->configuration & CFG_WRITE_TOGGLE_32BIT_ADDR) + stfsm_enter_32bit_addr(fsm, 0); + + return 0; +} + +/* + * Read an address range from the flash chip. The address range + * may be any size provided it is within the physical boundaries. + */ +static int stfsm_mtd_read(struct mtd_info *mtd, loff_t from, size_t len, + size_t *retlen, u_char *buf) +{ + struct stfsm *fsm = dev_get_drvdata(mtd->dev.parent); + uint32_t bytes; + + dev_dbg(fsm->dev, "%s from 0x%08x, len %zd\n", + __func__, (u32)from, len); + + mutex_lock(&fsm->lock); + + while (len > 0) { + bytes = min_t(size_t, len, FLASH_PAGESIZE); + + stfsm_read(fsm, buf, bytes, from); + + buf += bytes; + from += bytes; + len -= bytes; + + *retlen += bytes; + } + + mutex_unlock(&fsm->lock); + + return 0; +} + +static int stfsm_erase_sector(struct stfsm *fsm, uint32_t offset) +{ + struct stfsm_seq *seq = &stfsm_seq_erase_sector; + int ret; + + dev_dbg(fsm->dev, "erasing sector at 0x%08x\n", offset); + + /* Enter 32-bit address mode, if required */ + if (fsm->configuration & CFG_ERASESEC_TOGGLE_32BIT_ADDR) + stfsm_enter_32bit_addr(fsm, 1); + + seq->addr1 = (offset >> 16) & 0xffff; + seq->addr2 = offset & 0xffff; + + stfsm_load_seq(fsm, seq); + + stfsm_wait_seq(fsm); + + /* Wait for completion */ + ret = stfsm_wait_busy(fsm); + if (ret && fsm->configuration & CFG_S25FL_CHECK_ERROR_FLAGS) + stfsm_s25fl_clear_status_reg(fsm); + + /* Exit 32-bit address mode, if required */ + if (fsm->configuration & CFG_ERASESEC_TOGGLE_32BIT_ADDR) + stfsm_enter_32bit_addr(fsm, 0); + + return ret; +} + +static int stfsm_erase_chip(struct stfsm *fsm) +{ + const struct stfsm_seq *seq = &stfsm_seq_erase_chip; + + dev_dbg(fsm->dev, "erasing chip\n"); + + stfsm_load_seq(fsm, seq); + + stfsm_wait_seq(fsm); + + return stfsm_wait_busy(fsm); +} + +/* + * Write an address range to the flash chip. Data must be written in + * FLASH_PAGESIZE chunks. The address range may be any size provided + * it is within the physical boundaries. + */ +static int stfsm_mtd_write(struct mtd_info *mtd, loff_t to, size_t len, + size_t *retlen, const u_char *buf) +{ + struct stfsm *fsm = dev_get_drvdata(mtd->dev.parent); + + u32 page_offs; + u32 bytes; + uint8_t *b = (uint8_t *)buf; + int ret = 0; + + dev_dbg(fsm->dev, "%s to 0x%08x, len %zd\n", __func__, (u32)to, len); + + /* Offset within page */ + page_offs = to % FLASH_PAGESIZE; + + mutex_lock(&fsm->lock); + + while (len) { + /* Write up to page boundary */ + bytes = min_t(size_t, FLASH_PAGESIZE - page_offs, len); + + ret = stfsm_write(fsm, b, bytes, to); + if (ret) + goto out1; + + b += bytes; + len -= bytes; + to += bytes; + + /* We are now page-aligned */ + page_offs = 0; + + *retlen += bytes; + + } + +out1: + mutex_unlock(&fsm->lock); + + return ret; +} + +/* + * Erase an address range on the flash chip. The address range may extend + * one or more erase sectors. Return an error is there is a problem erasing. + */ +static int stfsm_mtd_erase(struct mtd_info *mtd, struct erase_info *instr) +{ + struct stfsm *fsm = dev_get_drvdata(mtd->dev.parent); + u32 addr, len; + int ret; + + dev_dbg(fsm->dev, "%s at 0x%llx, len %lld\n", __func__, + (long long)instr->addr, (long long)instr->len); + + addr = instr->addr; + len = instr->len; + + mutex_lock(&fsm->lock); + + /* Whole-chip erase? */ + if (len == mtd->size) { + ret = stfsm_erase_chip(fsm); + if (ret) + goto out1; + } else { + while (len) { + ret = stfsm_erase_sector(fsm, addr); + if (ret) + goto out1; + + addr += mtd->erasesize; + len -= mtd->erasesize; + } + } + + mutex_unlock(&fsm->lock); + + instr->state = MTD_ERASE_DONE; + mtd_erase_callback(instr); + + return 0; + +out1: + instr->state = MTD_ERASE_FAILED; + mutex_unlock(&fsm->lock); + + return ret; +} + +static void stfsm_read_jedec(struct stfsm *fsm, uint8_t *jedec) +{ + const struct stfsm_seq *seq = &stfsm_seq_read_jedec; + uint32_t tmp[2]; + + stfsm_load_seq(fsm, seq); + + stfsm_read_fifo(fsm, tmp, 8); + + memcpy(jedec, tmp, 5); + + stfsm_wait_seq(fsm); +} + +static struct flash_info *stfsm_jedec_probe(struct stfsm *fsm) +{ + struct flash_info *info; + u16 ext_jedec; + u32 jedec; + u8 id[5]; + + stfsm_read_jedec(fsm, id); + + jedec = id[0] << 16 | id[1] << 8 | id[2]; + /* + * JEDEC also defines an optional "extended device information" + * string for after vendor-specific data, after the three bytes + * we use here. Supporting some chips might require using it. + */ + ext_jedec = id[3] << 8 | id[4]; + + dev_dbg(fsm->dev, "JEDEC = 0x%08x [%02x %02x %02x %02x %02x]\n", + jedec, id[0], id[1], id[2], id[3], id[4]); + + for (info = flash_types; info->name; info++) { + if (info->jedec_id == jedec) { + if (info->ext_id && info->ext_id != ext_jedec) + continue; + return info; + } + } + dev_err(fsm->dev, "Unrecognized JEDEC id %06x\n", jedec); + + return NULL; +} + +static int stfsm_set_mode(struct stfsm *fsm, uint32_t mode) +{ + int ret, timeout = 10; + + /* Wait for controller to accept mode change */ + while (--timeout) { + ret = readl(fsm->base + SPI_STA_MODE_CHANGE); + if (ret & 0x1) + break; + udelay(1); + } + + if (!timeout) + return -EBUSY; + + writel(mode, fsm->base + SPI_MODESELECT); + + return 0; +} + +static void stfsm_set_freq(struct stfsm *fsm, uint32_t spi_freq) +{ + uint32_t emi_freq; + uint32_t clk_div; + + /* TODO: Make this dynamic */ + emi_freq = STFSM_DEFAULT_EMI_FREQ; + + /* + * Calculate clk_div - values between 2 and 128 + * Multiple of 2, rounded up + */ + clk_div = 2 * DIV_ROUND_UP(emi_freq, 2 * spi_freq); + if (clk_div < 2) + clk_div = 2; + else if (clk_div > 128) + clk_div = 128; + + /* + * Determine a suitable delay for the IP to complete a change of + * direction of the FIFO. The required delay is related to the clock + * divider used. The following heuristics are based on empirical tests, + * using a 100MHz EMI clock. + */ + if (clk_div <= 4) + fsm->fifo_dir_delay = 0; + else if (clk_div <= 10) + fsm->fifo_dir_delay = 1; + else + fsm->fifo_dir_delay = DIV_ROUND_UP(clk_div, 10); + + dev_dbg(fsm->dev, "emi_clk = %uHZ, spi_freq = %uHZ, clk_div = %u\n", + emi_freq, spi_freq, clk_div); + + writel(clk_div, fsm->base + SPI_CLOCKDIV); +} + +static int stfsm_init(struct stfsm *fsm) +{ + int ret; + + /* Perform a soft reset of the FSM controller */ + writel(SEQ_CFG_SWRESET, fsm->base + SPI_FAST_SEQ_CFG); + udelay(1); + writel(0, fsm->base + SPI_FAST_SEQ_CFG); + + /* Set clock to 'safe' frequency initially */ + stfsm_set_freq(fsm, STFSM_FLASH_SAFE_FREQ); + + /* Switch to FSM */ + ret = stfsm_set_mode(fsm, SPI_MODESELECT_FSM); + if (ret) + return ret; + + /* Set timing parameters */ + writel(SPI_CFG_DEVICE_ST | + SPI_CFG_DEFAULT_MIN_CS_HIGH | + SPI_CFG_DEFAULT_CS_SETUPHOLD | + SPI_CFG_DEFAULT_DATA_HOLD, + fsm->base + SPI_CONFIGDATA); + writel(STFSM_DEFAULT_WR_TIME, fsm->base + SPI_STATUS_WR_TIME_REG); + + /* + * Set the FSM 'WAIT' delay to the minimum workable value. Note, for + * our purposes, the WAIT instruction is used purely to achieve + * "sequence validity" rather than actually implement a delay. + */ + writel(0x00000001, fsm->base + SPI_PROGRAM_ERASE_TIME); + + /* Clear FIFO, just in case */ + stfsm_clear_fifo(fsm); + + return 0; +} + +static void stfsm_fetch_platform_configs(struct platform_device *pdev) +{ + struct stfsm *fsm = platform_get_drvdata(pdev); + struct device_node *np = pdev->dev.of_node; + struct regmap *regmap; + uint32_t boot_device_reg; + uint32_t boot_device_spi; + uint32_t boot_device; /* Value we read from *boot_device_reg */ + int ret; + + /* Booting from SPI NOR Flash is the default */ + fsm->booted_from_spi = true; + + regmap = syscon_regmap_lookup_by_phandle(np, "st,syscfg"); + if (IS_ERR(regmap)) + goto boot_device_fail; + + fsm->reset_signal = of_property_read_bool(np, "st,reset-signal"); + + fsm->reset_por = of_property_read_bool(np, "st,reset-por"); + + /* Where in the syscon the boot device information lives */ + ret = of_property_read_u32(np, "st,boot-device-reg", &boot_device_reg); + if (ret) + goto boot_device_fail; + + /* Boot device value when booted from SPI NOR */ + ret = of_property_read_u32(np, "st,boot-device-spi", &boot_device_spi); + if (ret) + goto boot_device_fail; + + ret = regmap_read(regmap, boot_device_reg, &boot_device); + if (ret) + goto boot_device_fail; + + if (boot_device != boot_device_spi) + fsm->booted_from_spi = false; + + return; + +boot_device_fail: + dev_warn(&pdev->dev, + "failed to fetch boot device, assuming boot from SPI\n"); +} + +static int stfsm_probe(struct platform_device *pdev) +{ + struct device_node *np = pdev->dev.of_node; + struct mtd_part_parser_data ppdata; + struct flash_info *info; + struct resource *res; + struct stfsm *fsm; + int ret; + + if (!np) { + dev_err(&pdev->dev, "No DT found\n"); + return -EINVAL; + } + ppdata.of_node = np; + + fsm = devm_kzalloc(&pdev->dev, sizeof(*fsm), GFP_KERNEL); + if (!fsm) + return -ENOMEM; + + fsm->dev = &pdev->dev; + + platform_set_drvdata(pdev, fsm); + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + dev_err(&pdev->dev, "Resource not found\n"); + return -ENODEV; + } + + fsm->base = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(fsm->base)) { + dev_err(&pdev->dev, + "Failed to reserve memory region %pR\n", res); + return PTR_ERR(fsm->base); + } + + mutex_init(&fsm->lock); + + ret = stfsm_init(fsm); + if (ret) { + dev_err(&pdev->dev, "Failed to initialise FSM Controller\n"); + return ret; + } + + stfsm_fetch_platform_configs(pdev); + + /* Detect SPI FLASH device */ + info = stfsm_jedec_probe(fsm); + if (!info) + return -ENODEV; + fsm->info = info; + + /* Use device size to determine address width */ + if (info->sector_size * info->n_sectors > 0x1000000) + info->flags |= FLASH_FLAG_32BIT_ADDR; + + /* + * Configure READ/WRITE/ERASE sequences according to platform and + * device flags. + */ + if (info->config) { + ret = info->config(fsm); + if (ret) + return ret; + } else { + ret = stfsm_prepare_rwe_seqs_default(fsm); + if (ret) + return ret; + } + + fsm->mtd.name = info->name; + fsm->mtd.dev.parent = &pdev->dev; + fsm->mtd.type = MTD_NORFLASH; + fsm->mtd.writesize = 4; + fsm->mtd.writebufsize = fsm->mtd.writesize; + fsm->mtd.flags = MTD_CAP_NORFLASH; + fsm->mtd.size = info->sector_size * info->n_sectors; + fsm->mtd.erasesize = info->sector_size; + + fsm->mtd._read = stfsm_mtd_read; + fsm->mtd._write = stfsm_mtd_write; + fsm->mtd._erase = stfsm_mtd_erase; + + dev_info(&pdev->dev, + "Found serial flash device: %s\n" + " size = %llx (%lldMiB) erasesize = 0x%08x (%uKiB)\n", + info->name, + (long long)fsm->mtd.size, (long long)(fsm->mtd.size >> 20), + fsm->mtd.erasesize, (fsm->mtd.erasesize >> 10)); + + return mtd_device_parse_register(&fsm->mtd, NULL, &ppdata, NULL, 0); +} + +static int stfsm_remove(struct platform_device *pdev) +{ + struct stfsm *fsm = platform_get_drvdata(pdev); + + return mtd_device_unregister(&fsm->mtd); +} + +static const struct of_device_id stfsm_match[] = { + { .compatible = "st,spi-fsm", }, + {}, +}; +MODULE_DEVICE_TABLE(of, stfsm_match); + +static struct platform_driver stfsm_driver = { + .probe = stfsm_probe, + .remove = stfsm_remove, + .driver = { + .name = "st-spi-fsm", + .owner = THIS_MODULE, + .of_match_table = stfsm_match, + }, +}; +module_platform_driver(stfsm_driver); + +MODULE_AUTHOR("Angus Clark <angus.clark@st.com>"); +MODULE_DESCRIPTION("ST SPI FSM driver"); +MODULE_LICENSE("GPL"); |