diff options
Diffstat (limited to 'drivers/message/fusion/lsi/mpi_log_sas.h')
| -rw-r--r-- | drivers/message/fusion/lsi/mpi_log_sas.h | 53 |
1 files changed, 39 insertions, 14 deletions
diff --git a/drivers/message/fusion/lsi/mpi_log_sas.h b/drivers/message/fusion/lsi/mpi_log_sas.h index af9da03e95e..f62960b5d52 100644 --- a/drivers/message/fusion/lsi/mpi_log_sas.h +++ b/drivers/message/fusion/lsi/mpi_log_sas.h @@ -1,6 +1,6 @@ /*************************************************************************** * * - * Copyright 2003 LSI Corporation. All rights reserved. * + * Copyright (c) 2000-2008 LSI Corporation. All rights reserved. * * * * Description * * ------------ * @@ -56,9 +56,9 @@ #define IOP_LOGINFO_CODE_FWUPLOAD_NO_FLASH_AVAILABLE (0x0003E000) /* Tried to upload from flash, but there is none */ #define IOP_LOGINFO_CODE_FWUPLOAD_UNKNOWN_IMAGE_TYPE (0x0003E001) /* ImageType field contents were invalid */ #define IOP_LOGINFO_CODE_FWUPLOAD_WRONG_IMAGE_SIZE (0x0003E002) /* ImageSize field in TCSGE was bad/offset in MfgPg 4 was wrong */ -#define IOP_LOGINFO_CODE_FWUPLOAD_ENTIRE_FLASH_UPLOAD_FAILED (0x0003E003) /* Error occured while attempting to upload the entire flash */ -#define IOP_LOGINFO_CODE_FWUPLOAD_REGION_UPLOAD_FAILED (0x0003E004) /* Error occured while attempting to upload single flash region */ -#define IOP_LOGINFO_CODE_FWUPLOAD_DMA_FAILURE (0x0003E005) /* Problem occured while DMAing FW to host memory */ +#define IOP_LOGINFO_CODE_FWUPLOAD_ENTIRE_FLASH_UPLOAD_FAILED (0x0003E003) /* Error occurred while attempting to upload the entire flash */ +#define IOP_LOGINFO_CODE_FWUPLOAD_REGION_UPLOAD_FAILED (0x0003E004) /* Error occurred while attempting to upload single flash region */ +#define IOP_LOGINFO_CODE_FWUPLOAD_DMA_FAILURE (0x0003E005) /* Problem occurred while DMAing FW to host memory */ #define IOP_LOGINFO_CODE_DIAG_MSG_ERROR (0x00040000) /* Error handling diag msg - or'd with diag status */ @@ -73,6 +73,8 @@ #define IOP_LOGINFO_CODE_TARGET_MODE_ABORT_EXACT_IO (0x00070004) #define IOP_LOGINFO_CODE_TARGET_MODE_ABORT_EXACT_IO_REQ (0x00070005) +#define IOP_LOGINFO_CODE_LOG_TIMESTAMP_EVENT (0x00080000) + /****************************************************************************/ /* PL LOGINFO_CODE defines, valid if IOC_LOGINFO_ORIGINATOR = PL */ /****************************************************************************/ @@ -92,7 +94,7 @@ #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_OPEN_TIMEOUT_EXP (0x0000000C) #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_UNUSED_0D (0x0000000D) #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_DVTBLE_ACCSS_FAIL (0x0000000E) -#define PL_LOGINFO_SUB CODE_OPEN_FAIL_BAD_DEST (0x00000011) +#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_BAD_DEST (0x00000011) #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RATE_NOT_SUPP (0x00000012) #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_PROT_NOT_SUPP (0x00000013) #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RESERVED_ABANDON0 (0x00000014) @@ -159,10 +161,11 @@ #define PL_LOGINFO_SUB_CODE_INVALID_SGL (0x00000200) #define PL_LOGINFO_SUB_CODE_WRONG_REL_OFF_OR_FRAME_LENGTH (0x00000300) -#define PL_LOGINFO_SUB_CODE_FRAME_XFER_ERROR (0x00000400) /* Bits 0-3 encode Transport Status Register (offset 0x08) */ - /* Bit 0 is Status Bit 0: FrameXferErr */ - /* Bit 1 & 2 are Status Bits 16 and 17: FrameXmitErrStatus */ - /* Bit 3 is Status Bit 18 WriteDataLengthGTDataLengthErr */ +#define PL_LOGINFO_SUB_CODE_FRAME_XFER_ERROR (0x00000400) +/* Bits 0-3 encode Transport Status Register (offset 0x08) */ +/* Bit 0 is Status Bit 0: FrameXferErr */ +/* Bit 1 & 2 are Status Bits 16 and 17: FrameXmitErrStatus */ +/* Bit 3 is Status Bit 18 WriteDataLenghtGTDataLengthErr */ #define PL_LOGINFO_SUB_CODE_TX_FM_CONNECTED_LOW (0x00000500) #define PL_LOGINFO_SUB_CODE_SATA_NON_NCQ_RW_ERR_BIT_SET (0x00000600) @@ -177,10 +180,15 @@ #define PL_LOGINFO_SUB_CODE_DISCOVERY_REMOTE_SEP_RESET (0x00000E01) #define PL_LOGINFO_SUB_CODE_SECOND_OPEN (0x00000F00) #define PL_LOGINFO_SUB_CODE_DSCVRY_SATA_INIT_TIMEOUT (0x00001000) +#define PL_LOGINFO_SUB_CODE_BREAK_ON_SATA_CONNECTION (0x00002000) +/* not currently used in mainline */ +#define PL_LOGINFO_SUB_CODE_BREAK_ON_STUCK_LINK (0x00003000) +#define PL_LOGINFO_SUB_CODE_BREAK_ON_STUCK_LINK_AIP (0x00004000) +#define PL_LOGINFO_SUB_CODE_BREAK_ON_INCOMPLETE_BREAK_RCVD (0x00005000) #define PL_LOGINFO_CODE_ENCL_MGMT_SMP_FRAME_FAILURE (0x00200000) /* Can't get SMP Frame */ -#define PL_LOGINFO_CODE_ENCL_MGMT_SMP_READ_ERROR (0x00200010) /* Error occured on SMP Read */ -#define PL_LOGINFO_CODE_ENCL_MGMT_SMP_WRITE_ERROR (0x00200020) /* Error occured on SMP Write */ +#define PL_LOGINFO_CODE_ENCL_MGMT_SMP_READ_ERROR (0x00200010) /* Error occurred on SMP Read */ +#define PL_LOGINFO_CODE_ENCL_MGMT_SMP_WRITE_ERROR (0x00200020) /* Error occurred on SMP Write */ #define PL_LOGINFO_CODE_ENCL_MGMT_NOT_SUPPORTED_ON_ENCL (0x00200040) /* Encl Mgmt services not available for this WWID */ #define PL_LOGINFO_CODE_ENCL_MGMT_ADDR_MODE_NOT_SUPPORTED (0x00200050) /* Address Mode not suppored */ #define PL_LOGINFO_CODE_ENCL_MGMT_BAD_SLOT_NUM (0x00200060) /* Invalid Slot Number in SEP Msg */ @@ -199,8 +207,8 @@ #define PL_LOGINFO_DA_SEP_RECEIVED_NACK_FROM_SLAVE (0x00200103) /* SEP NACK'd, it is busy */ #define PL_LOGINFO_DA_SEP_DID_NOT_RECEIVE_ACK (0x00200104) /* SEP didn't rcv. ACK (Last Rcvd Bit = 1) */ #define PL_LOGINFO_DA_SEP_BAD_STATUS_HDR_CHKSUM (0x00200105) /* SEP stopped or sent bad chksum in Hdr */ -#define PL_LOGINFO_DA_SEP_STOP_ON_DATA (0x00200106) /* SEP stopped while transfering data */ -#define PL_LOGINFO_DA_SEP_STOP_ON_SENSE_DATA (0x00200107) /* SEP stopped while transfering sense data */ +#define PL_LOGINFO_DA_SEP_STOP_ON_DATA (0x00200106) /* SEP stopped while transferring data */ +#define PL_LOGINFO_DA_SEP_STOP_ON_SENSE_DATA (0x00200107) /* SEP stopped while transferring sense data */ #define PL_LOGINFO_DA_SEP_UNSUPPORTED_SCSI_STATUS_1 (0x00200108) /* SEP returned unknown scsi status */ #define PL_LOGINFO_DA_SEP_UNSUPPORTED_SCSI_STATUS_2 (0x00200109) /* SEP returned unknown scsi status */ #define PL_LOGINFO_DA_SEP_CHKSUM_ERROR_AFTER_STOP (0x0020010A) /* SEP returned bad chksum after STOP */ @@ -243,6 +251,8 @@ #define IR_LOGINFO_VOLUME_ACTIVATE_VOLUME_FAILED (0x00010014) /* Activation failed trying to import the volume */ #define IR_LOGINFO_VOLUME_ACTIVATING_IMPORT_VOLUME_FAILED (0x00010015) +/* Activation failed trying to import the volume */ +#define IR_LOGINFO_VOLUME_ACTIVATING_TOO_MANY_PHYS_DISKS (0x00010016) /* Phys Disk failed, too many phys disks */ #define IR_LOGINFO_PHYSDISK_CREATE_TOO_MANY_DISKS (0x00010020) @@ -258,7 +268,7 @@ /* Compatibility Error : IR Disabled */ #define IR_LOGINFO_COMPAT_ERROR_RAID_DISABLED (0x00010030) -/* Compatibility Error : Inquiry Comand failed */ +/* Compatibility Error : Inquiry Command failed */ #define IR_LOGINFO_COMPAT_ERROR_INQUIRY_FAILED (0x00010031) /* Compatibility Error : Device not direct access device */ #define IR_LOGINFO_COMPAT_ERROR_NOT_DIRECT_ACCESS (0x00010032) @@ -285,6 +295,21 @@ /* Compatibility Error : IME size limited to < 2TB */ #define IR_LOGINFO_COMPAT_ERROR_IME_VOL_NOT_CURRENTLY_SUPPORTED (0x0001003D) +/* Device Firmware Update: DFU can only be started once */ +#define IR_LOGINFO_DEV_FW_UPDATE_ERR_DFU_IN_PROGRESS (0x00010050) +/* Device Firmware Update: Volume must be Optimal/Active/non-Quiesced */ +#define IR_LOGINFO_DEV_FW_UPDATE_ERR_DEVICE_IN_INVALID_STATE (0x00010051) +/* Device Firmware Update: DFU Timeout cannot be zero */ +#define IR_LOGINFO_DEV_FW_UPDATE_ERR_INVALID_TIMEOUT (0x00010052) +/* Device Firmware Update: CREATE TIMER FAILED */ +#define IR_LOGINFO_DEV_FW_UPDATE_ERR_NO_TIMERS (0x00010053) +/* Device Firmware Update: Failed to read SAS_IO_UNIT_PG_1 */ +#define IR_LOGINFO_DEV_FW_UPDATE_ERR_READING_CFG_PAGE (0x00010054) +/* Device Firmware Update: Invalid SAS_IO_UNIT_PG_1 value(s) */ +#define IR_LOGINFO_DEV_FW_UPDATE_ERR_PORT_IO_TIMEOUTS_REQUIRED (0x00010055) +/* Device Firmware Update: Unable to allocate memory for page */ +#define IR_LOGINFO_DEV_FW_UPDATE_ERR_ALLOC_CFG_PAGE (0x00010056) + /****************************************************************************/ /* Defines for convenience */ |