diff options
Diffstat (limited to 'drivers/memory')
| -rw-r--r-- | drivers/memory/Kconfig | 25 | ||||
| -rw-r--r-- | drivers/memory/Makefile | 3 | ||||
| -rw-r--r-- | drivers/memory/emif.c | 155 | ||||
| -rw-r--r-- | drivers/memory/fsl_ifc.c | 309 | ||||
| -rw-r--r-- | drivers/memory/mvebu-devbus.c | 362 | ||||
| -rw-r--r-- | drivers/memory/tegra20-mc.c | 14 | ||||
| -rw-r--r-- | drivers/memory/tegra30-mc.c | 20 | ||||
| -rw-r--r-- | drivers/memory/ti-aemif.c | 427 |
8 files changed, 1263 insertions, 52 deletions
diff --git a/drivers/memory/Kconfig b/drivers/memory/Kconfig index 067f31174a0..c59e9c96e86 100644 --- a/drivers/memory/Kconfig +++ b/drivers/memory/Kconfig @@ -7,6 +7,17 @@ menuconfig MEMORY if MEMORY +config TI_AEMIF + tristate "Texas Instruments AEMIF driver" + depends on (ARCH_DAVINCI || ARCH_KEYSTONE) && OF + help + This driver is for the AEMIF module available in Texas Instruments + SoCs. AEMIF stands for Asynchronous External Memory Interface and + is intended to provide a glue-less interface to a variety of + asynchronuous memory devices like ASRAM, NOR and NAND memory. A total + of 256M bytes of any of these memories can be accessed at a given + time via four chip selects with 64M byte access per chip select. + config TI_EMIF tristate "Texas Instruments EMIF driver" depends on ARCH_OMAP2PLUS @@ -20,6 +31,16 @@ config TI_EMIF parameters and other settings during frequency, voltage and temperature changes +config MVEBU_DEVBUS + bool "Marvell EBU Device Bus Controller" + default y + depends on PLAT_ORION && OF + help + This driver is for the Device Bus controller available in some + Marvell EBU SoCs such as Discovery (mv78xx0), Orion (88f5xxx) and + Armada 370 and Armada XP. This controller allows to handle flash + devices such as NOR, NAND, SRAM, and FPGA. + config TEGRA20_MC bool "Tegra20 Memory Controller(MC) driver" default y @@ -40,4 +61,8 @@ config TEGRA30_MC analysis, especially for IOMMU/SMMU(System Memory Management Unit) module. +config FSL_IFC + bool + depends on FSL_SOC + endif diff --git a/drivers/memory/Makefile b/drivers/memory/Makefile index 9cce5d70ed5..71160a2b731 100644 --- a/drivers/memory/Makefile +++ b/drivers/memory/Makefile @@ -5,6 +5,9 @@ ifeq ($(CONFIG_DDR),y) obj-$(CONFIG_OF) += of_memory.o endif +obj-$(CONFIG_TI_AEMIF) += ti-aemif.o obj-$(CONFIG_TI_EMIF) += emif.o +obj-$(CONFIG_FSL_IFC) += fsl_ifc.o +obj-$(CONFIG_MVEBU_DEVBUS) += mvebu-devbus.o obj-$(CONFIG_TEGRA20_MC) += tegra20-mc.o obj-$(CONFIG_TEGRA30_MC) += tegra30-mc.o diff --git a/drivers/memory/emif.c b/drivers/memory/emif.c index 06d31c99e6a..04644e7b42b 100644 --- a/drivers/memory/emif.c +++ b/drivers/memory/emif.c @@ -10,6 +10,7 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ +#include <linux/err.h> #include <linux/kernel.h> #include <linux/reboot.h> #include <linux/platform_data/emif_plat.h> @@ -24,6 +25,7 @@ #include <linux/module.h> #include <linux/list.h> #include <linux/spinlock.h> +#include <linux/pm.h> #include <memory/jedec_ddr.h> #include "emif.h" #include "of_memory.h" @@ -255,6 +257,41 @@ static void set_lpmode(struct emif_data *emif, u8 lpmode) u32 temp; void __iomem *base = emif->base; + /* + * Workaround for errata i743 - LPDDR2 Power-Down State is Not + * Efficient + * + * i743 DESCRIPTION: + * The EMIF supports power-down state for low power. The EMIF + * automatically puts the SDRAM into power-down after the memory is + * not accessed for a defined number of cycles and the + * EMIF_PWR_MGMT_CTRL[10:8] REG_LP_MODE bit field is set to 0x4. + * As the EMIF supports automatic output impedance calibration, a ZQ + * calibration long command is issued every time it exits active + * power-down and precharge power-down modes. The EMIF waits and + * blocks any other command during this calibration. + * The EMIF does not allow selective disabling of ZQ calibration upon + * exit of power-down mode. Due to very short periods of power-down + * cycles, ZQ calibration overhead creates bandwidth issues and + * increases overall system power consumption. On the other hand, + * issuing ZQ calibration long commands when exiting self-refresh is + * still required. + * + * WORKAROUND + * Because there is no power consumption benefit of the power-down due + * to the calibration and there is a performance risk, the guideline + * is to not allow power-down state and, therefore, to not have set + * the EMIF_PWR_MGMT_CTRL[10:8] REG_LP_MODE bit field to 0x4. + */ + if ((emif->plat_data->ip_rev == EMIF_4D) && + (EMIF_LP_MODE_PWR_DN == lpmode)) { + WARN_ONCE(1, + "REG_LP_MODE = LP_MODE_PWR_DN(4) is prohibited by" + "erratum i743 switch to LP_MODE_SELF_REFRESH(2)\n"); + /* rollback LP_MODE to Self-refresh mode */ + lpmode = EMIF_LP_MODE_SELF_REFRESH; + } + temp = readl(base + EMIF_POWER_MANAGEMENT_CONTROL); temp &= ~LP_MODE_MASK; temp |= (lpmode << LP_MODE_SHIFT); @@ -714,6 +751,8 @@ static u32 get_pwr_mgmt_ctrl(u32 freq, struct emif_data *emif, u32 ip_rev) u32 timeout_perf = EMIF_LP_MODE_TIMEOUT_PERFORMANCE; u32 timeout_pwr = EMIF_LP_MODE_TIMEOUT_POWER; u32 freq_threshold = EMIF_LP_MODE_FREQ_THRESHOLD; + u32 mask; + u8 shift; struct emif_custom_configs *cust_cfgs = emif->plat_data->custom_configs; @@ -727,37 +766,59 @@ static u32 get_pwr_mgmt_ctrl(u32 freq, struct emif_data *emif, u32 ip_rev) /* Timeout based on DDR frequency */ timeout = freq >= freq_threshold ? timeout_perf : timeout_pwr; - /* The value to be set in register is "log2(timeout) - 3" */ + /* + * The value to be set in register is "log2(timeout) - 3" + * if timeout < 16 load 0 in register + * if timeout is not a power of 2, round to next highest power of 2 + */ if (timeout < 16) { timeout = 0; } else { - timeout = __fls(timeout) - 3; if (timeout & (timeout - 1)) - timeout++; + timeout <<= 1; + timeout = __fls(timeout) - 3; } switch (lpmode) { case EMIF_LP_MODE_CLOCK_STOP: - pwr_mgmt_ctrl = (timeout << CS_TIM_SHIFT) | - SR_TIM_MASK | PD_TIM_MASK; + shift = CS_TIM_SHIFT; + mask = CS_TIM_MASK; break; case EMIF_LP_MODE_SELF_REFRESH: /* Workaround for errata i735 */ if (timeout < 6) timeout = 6; - pwr_mgmt_ctrl = (timeout << SR_TIM_SHIFT) | - CS_TIM_MASK | PD_TIM_MASK; + shift = SR_TIM_SHIFT; + mask = SR_TIM_MASK; break; case EMIF_LP_MODE_PWR_DN: - pwr_mgmt_ctrl = (timeout << PD_TIM_SHIFT) | - CS_TIM_MASK | SR_TIM_MASK; + shift = PD_TIM_SHIFT; + mask = PD_TIM_MASK; break; case EMIF_LP_MODE_DISABLE: default: - pwr_mgmt_ctrl = CS_TIM_MASK | - PD_TIM_MASK | SR_TIM_MASK; + mask = 0; + shift = 0; + break; } + /* Round to maximum in case of overflow, BUT warn! */ + if (lpmode != EMIF_LP_MODE_DISABLE && timeout > mask >> shift) { + pr_err("TIMEOUT Overflow - lpmode=%d perf=%d pwr=%d freq=%d\n", + lpmode, + timeout_perf, + timeout_pwr, + freq_threshold); + WARN(1, "timeout=0x%02x greater than 0x%02x. Using max\n", + timeout, mask >> shift); + timeout = mask >> shift; + } + + /* Setup required timing */ + pwr_mgmt_ctrl = (timeout << shift) & mask; + /* setup a default mask for rest of the modes */ + pwr_mgmt_ctrl |= (SR_TIM_MASK | CS_TIM_MASK | PD_TIM_MASK) & + ~mask; /* No CS_TIM in EMIF_4D5 */ if (ip_rev == EMIF_4D5) @@ -814,6 +875,8 @@ static void setup_registers(struct emif_data *emif, struct emif_regs *regs) writel(regs->sdram_tim2_shdw, base + EMIF_SDRAM_TIMING_2_SHDW); writel(regs->phy_ctrl_1_shdw, base + EMIF_DDR_PHY_CTRL_1_SHDW); + writel(regs->pwr_mgmt_ctrl_shdw, + base + EMIF_POWER_MANAGEMENT_CTRL_SHDW); /* Settings specific for EMIF4D5 */ if (emif->plat_data->ip_rev != EMIF_4D5) @@ -891,6 +954,7 @@ static irqreturn_t handle_temp_alert(void __iomem *base, struct emif_data *emif) { u32 old_temp_level; irqreturn_t ret = IRQ_HANDLED; + struct emif_custom_configs *custom_configs; spin_lock_irqsave(&emif_lock, irq_state); old_temp_level = emif->temperature_level; @@ -903,6 +967,29 @@ static irqreturn_t handle_temp_alert(void __iomem *base, struct emif_data *emif) goto out; } + custom_configs = emif->plat_data->custom_configs; + + /* + * IF we detect higher than "nominal rating" from DDR sensor + * on an unsupported DDR part, shutdown system + */ + if (custom_configs && !(custom_configs->mask & + EMIF_CUSTOM_CONFIG_EXTENDED_TEMP_PART)) { + if (emif->temperature_level >= SDRAM_TEMP_HIGH_DERATE_REFRESH) { + dev_err(emif->dev, + "%s:NOT Extended temperature capable memory." + "Converting MR4=0x%02x as shutdown event\n", + __func__, emif->temperature_level); + /* + * Temperature far too high - do kernel_power_off() + * from thread context + */ + emif->temperature_level = SDRAM_TEMP_VERY_HIGH_SHUTDOWN; + ret = IRQ_WAKE_THREAD; + goto out; + } + } + if (emif->temperature_level < old_temp_level || emif->temperature_level == SDRAM_TEMP_VERY_HIGH_SHUTDOWN) { /* @@ -964,7 +1051,14 @@ static irqreturn_t emif_threaded_isr(int irq, void *dev_id) if (emif->temperature_level == SDRAM_TEMP_VERY_HIGH_SHUTDOWN) { dev_emerg(emif->dev, "SDRAM temperature exceeds operating limit.. Needs shut down!!!\n"); - kernel_power_off(); + + /* If we have Power OFF ability, use it, else try restarting */ + if (pm_power_off) { + kernel_power_off(); + } else { + WARN(1, "FIXME: NO pm_power_off!!! trying restart\n"); + kernel_restart("SDRAM Over-temp Emergency restart"); + } return IRQ_HANDLED; } @@ -1169,7 +1263,7 @@ static void __init_or_module of_get_custom_configs(struct device_node *np_emif, { struct emif_custom_configs *cust_cfgs = NULL; int len; - const int *lpmode, *poll_intvl; + const __be32 *lpmode, *poll_intvl; lpmode = of_get_property(np_emif, "low-power-mode", &len); poll_intvl = of_get_property(np_emif, "temp-alert-poll-interval", &len); @@ -1183,7 +1277,7 @@ static void __init_or_module of_get_custom_configs(struct device_node *np_emif, if (lpmode) { cust_cfgs->mask |= EMIF_CUSTOM_CONFIG_LPMODE; - cust_cfgs->lpmode = *lpmode; + cust_cfgs->lpmode = be32_to_cpup(lpmode); of_property_read_u32(np_emif, "low-power-mode-timeout-performance", &cust_cfgs->lpmode_timeout_performance); @@ -1198,9 +1292,13 @@ static void __init_or_module of_get_custom_configs(struct device_node *np_emif, if (poll_intvl) { cust_cfgs->mask |= EMIF_CUSTOM_CONFIG_TEMP_ALERT_POLL_INTERVAL; - cust_cfgs->temp_alert_poll_interval_ms = *poll_intvl; + cust_cfgs->temp_alert_poll_interval_ms = + be32_to_cpup(poll_intvl); } + if (of_find_property(np_emif, "extended-temp-part", &len)) + cust_cfgs->mask |= EMIF_CUSTOM_CONFIG_EXTENDED_TEMP_PART; + if (!is_custom_config_valid(cust_cfgs, emif->dev)) { devm_kfree(emif->dev, cust_cfgs); return; @@ -1406,7 +1504,7 @@ static struct emif_data *__init_or_module get_device_details( if (pd->timings) { temp = devm_kzalloc(dev, size, GFP_KERNEL); if (temp) { - memcpy(temp, pd->timings, sizeof(*pd->timings)); + memcpy(temp, pd->timings, size); pd->timings = temp; } else { dev_warn(dev, "%s:%d: allocation error\n", __func__, @@ -1462,18 +1560,9 @@ static int __init_or_module emif_probe(struct platform_device *pdev) platform_set_drvdata(pdev, emif); res = platform_get_resource(pdev, IORESOURCE_MEM, 0); - if (!res) { - dev_err(emif->dev, "%s: error getting memory resource\n", - __func__); + emif->base = devm_ioremap_resource(emif->dev, res); + if (IS_ERR(emif->base)) goto error; - } - - emif->base = devm_request_and_ioremap(emif->dev, res); - if (!emif->base) { - dev_err(emif->dev, "%s: devm_request_and_ioremap() failed\n", - __func__); - goto error; - } irq = platform_get_irq(pdev, 0); if (irq < 0) { @@ -1843,18 +1932,8 @@ static struct platform_driver emif_driver = { }, }; -static int __init_or_module emif_register(void) -{ - return platform_driver_probe(&emif_driver, emif_probe); -} - -static void __exit emif_unregister(void) -{ - platform_driver_unregister(&emif_driver); -} +module_platform_driver_probe(emif_driver, emif_probe); -module_init(emif_register); -module_exit(emif_unregister); MODULE_DESCRIPTION("TI EMIF SDRAM Controller Driver"); MODULE_LICENSE("GPL"); MODULE_ALIAS("platform:emif"); diff --git a/drivers/memory/fsl_ifc.c b/drivers/memory/fsl_ifc.c new file mode 100644 index 00000000000..3d5d792d5cb --- /dev/null +++ b/drivers/memory/fsl_ifc.c @@ -0,0 +1,309 @@ +/* + * Copyright 2011 Freescale Semiconductor, Inc + * + * Freescale Integrated Flash Controller + * + * Author: Dipen Dudhat <Dipen.Dudhat@freescale.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/compiler.h> +#include <linux/spinlock.h> +#include <linux/types.h> +#include <linux/slab.h> +#include <linux/io.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/platform_device.h> +#include <linux/fsl_ifc.h> +#include <asm/prom.h> + +struct fsl_ifc_ctrl *fsl_ifc_ctrl_dev; +EXPORT_SYMBOL(fsl_ifc_ctrl_dev); + +/* + * convert_ifc_address - convert the base address + * @addr_base: base address of the memory bank + */ +unsigned int convert_ifc_address(phys_addr_t addr_base) +{ + return addr_base & CSPR_BA; +} +EXPORT_SYMBOL(convert_ifc_address); + +/* + * fsl_ifc_find - find IFC bank + * @addr_base: base address of the memory bank + * + * This function walks IFC banks comparing "Base address" field of the CSPR + * registers with the supplied addr_base argument. When bases match this + * function returns bank number (starting with 0), otherwise it returns + * appropriate errno value. + */ +int fsl_ifc_find(phys_addr_t addr_base) +{ + int i = 0; + + if (!fsl_ifc_ctrl_dev || !fsl_ifc_ctrl_dev->regs) + return -ENODEV; + + for (i = 0; i < ARRAY_SIZE(fsl_ifc_ctrl_dev->regs->cspr_cs); i++) { + u32 cspr = in_be32(&fsl_ifc_ctrl_dev->regs->cspr_cs[i].cspr); + if (cspr & CSPR_V && (cspr & CSPR_BA) == + convert_ifc_address(addr_base)) + return i; + } + + return -ENOENT; +} +EXPORT_SYMBOL(fsl_ifc_find); + +static int fsl_ifc_ctrl_init(struct fsl_ifc_ctrl *ctrl) +{ + struct fsl_ifc_regs __iomem *ifc = ctrl->regs; + + /* + * Clear all the common status and event registers + */ + if (in_be32(&ifc->cm_evter_stat) & IFC_CM_EVTER_STAT_CSER) + out_be32(&ifc->cm_evter_stat, IFC_CM_EVTER_STAT_CSER); + + /* enable all error and events */ + out_be32(&ifc->cm_evter_en, IFC_CM_EVTER_EN_CSEREN); + + /* enable all error and event interrupts */ + out_be32(&ifc->cm_evter_intr_en, IFC_CM_EVTER_INTR_EN_CSERIREN); + out_be32(&ifc->cm_erattr0, 0x0); + out_be32(&ifc->cm_erattr1, 0x0); + + return 0; +} + +static int fsl_ifc_ctrl_remove(struct platform_device *dev) +{ + struct fsl_ifc_ctrl *ctrl = dev_get_drvdata(&dev->dev); + + free_irq(ctrl->nand_irq, ctrl); + free_irq(ctrl->irq, ctrl); + + irq_dispose_mapping(ctrl->nand_irq); + irq_dispose_mapping(ctrl->irq); + + iounmap(ctrl->regs); + + dev_set_drvdata(&dev->dev, NULL); + kfree(ctrl); + + return 0; +} + +/* + * NAND events are split between an operational interrupt which only + * receives OPC, and an error interrupt that receives everything else, + * including non-NAND errors. Whichever interrupt gets to it first + * records the status and wakes the wait queue. + */ +static DEFINE_SPINLOCK(nand_irq_lock); + +static u32 check_nand_stat(struct fsl_ifc_ctrl *ctrl) +{ + struct fsl_ifc_regs __iomem *ifc = ctrl->regs; + unsigned long flags; + u32 stat; + + spin_lock_irqsave(&nand_irq_lock, flags); + + stat = in_be32(&ifc->ifc_nand.nand_evter_stat); + if (stat) { + out_be32(&ifc->ifc_nand.nand_evter_stat, stat); + ctrl->nand_stat = stat; + wake_up(&ctrl->nand_wait); + } + + spin_unlock_irqrestore(&nand_irq_lock, flags); + + return stat; +} + +static irqreturn_t fsl_ifc_nand_irq(int irqno, void *data) +{ + struct fsl_ifc_ctrl *ctrl = data; + + if (check_nand_stat(ctrl)) + return IRQ_HANDLED; + + return IRQ_NONE; +} + +/* + * NOTE: This interrupt is used to report ifc events of various kinds, + * such as transaction errors on the chipselects. + */ +static irqreturn_t fsl_ifc_ctrl_irq(int irqno, void *data) +{ + struct fsl_ifc_ctrl *ctrl = data; + struct fsl_ifc_regs __iomem *ifc = ctrl->regs; + u32 err_axiid, err_srcid, status, cs_err, err_addr; + irqreturn_t ret = IRQ_NONE; + + /* read for chip select error */ + cs_err = in_be32(&ifc->cm_evter_stat); + if (cs_err) { + dev_err(ctrl->dev, "transaction sent to IFC is not mapped to" + "any memory bank 0x%08X\n", cs_err); + /* clear the chip select error */ + out_be32(&ifc->cm_evter_stat, IFC_CM_EVTER_STAT_CSER); + + /* read error attribute registers print the error information */ + status = in_be32(&ifc->cm_erattr0); + err_addr = in_be32(&ifc->cm_erattr1); + + if (status & IFC_CM_ERATTR0_ERTYP_READ) + dev_err(ctrl->dev, "Read transaction error" + "CM_ERATTR0 0x%08X\n", status); + else + dev_err(ctrl->dev, "Write transaction error" + "CM_ERATTR0 0x%08X\n", status); + + err_axiid = (status & IFC_CM_ERATTR0_ERAID) >> + IFC_CM_ERATTR0_ERAID_SHIFT; + dev_err(ctrl->dev, "AXI ID of the error" + "transaction 0x%08X\n", err_axiid); + + err_srcid = (status & IFC_CM_ERATTR0_ESRCID) >> + IFC_CM_ERATTR0_ESRCID_SHIFT; + dev_err(ctrl->dev, "SRC ID of the error" + "transaction 0x%08X\n", err_srcid); + + dev_err(ctrl->dev, "Transaction Address corresponding to error" + "ERADDR 0x%08X\n", err_addr); + + ret = IRQ_HANDLED; + } + + if (check_nand_stat(ctrl)) + ret = IRQ_HANDLED; + + return ret; +} + +/* + * fsl_ifc_ctrl_probe + * + * called by device layer when it finds a device matching + * one our driver can handled. This code allocates all of + * the resources needed for the controller only. The + * resources for the NAND banks themselves are allocated + * in the chip probe function. +*/ +static int fsl_ifc_ctrl_probe(struct platform_device *dev) +{ + int ret = 0; + + + dev_info(&dev->dev, "Freescale Integrated Flash Controller\n"); + + fsl_ifc_ctrl_dev = kzalloc(sizeof(*fsl_ifc_ctrl_dev), GFP_KERNEL); + if (!fsl_ifc_ctrl_dev) + return -ENOMEM; + + dev_set_drvdata(&dev->dev, fsl_ifc_ctrl_dev); + + /* IOMAP the entire IFC region */ + fsl_ifc_ctrl_dev->regs = of_iomap(dev->dev.of_node, 0); + if (!fsl_ifc_ctrl_dev->regs) { + dev_err(&dev->dev, "failed to get memory region\n"); + ret = -ENODEV; + goto err; + } + + /* get the Controller level irq */ + fsl_ifc_ctrl_dev->irq = irq_of_parse_and_map(dev->dev.of_node, 0); + if (fsl_ifc_ctrl_dev->irq == NO_IRQ) { + dev_err(&dev->dev, "failed to get irq resource " + "for IFC\n"); + ret = -ENODEV; + goto err; + } + + /* get the nand machine irq */ + fsl_ifc_ctrl_dev->nand_irq = + irq_of_parse_and_map(dev->dev.of_node, 1); + + fsl_ifc_ctrl_dev->dev = &dev->dev; + + ret = fsl_ifc_ctrl_init(fsl_ifc_ctrl_dev); + if (ret < 0) + goto err; + + init_waitqueue_head(&fsl_ifc_ctrl_dev->nand_wait); + + ret = request_irq(fsl_ifc_ctrl_dev->irq, fsl_ifc_ctrl_irq, IRQF_SHARED, + "fsl-ifc", fsl_ifc_ctrl_dev); + if (ret != 0) { + dev_err(&dev->dev, "failed to install irq (%d)\n", + fsl_ifc_ctrl_dev->irq); + goto err_irq; + } + + if (fsl_ifc_ctrl_dev->nand_irq) { + ret = request_irq(fsl_ifc_ctrl_dev->nand_irq, fsl_ifc_nand_irq, + 0, "fsl-ifc-nand", fsl_ifc_ctrl_dev); + if (ret != 0) { + dev_err(&dev->dev, "failed to install irq (%d)\n", + fsl_ifc_ctrl_dev->nand_irq); + goto err_nandirq; + } + } + + return 0; + +err_nandirq: + free_irq(fsl_ifc_ctrl_dev->nand_irq, fsl_ifc_ctrl_dev); + irq_dispose_mapping(fsl_ifc_ctrl_dev->nand_irq); +err_irq: + free_irq(fsl_ifc_ctrl_dev->irq, fsl_ifc_ctrl_dev); + irq_dispose_mapping(fsl_ifc_ctrl_dev->irq); +err: + return ret; +} + +static const struct of_device_id fsl_ifc_match[] = { + { + .compatible = "fsl,ifc", + }, + {}, +}; + +static struct platform_driver fsl_ifc_ctrl_driver = { + .driver = { + .name = "fsl-ifc", + .of_match_table = fsl_ifc_match, + }, + .probe = fsl_ifc_ctrl_probe, + .remove = fsl_ifc_ctrl_remove, +}; + +static int __init fsl_ifc_init(void) +{ + return platform_driver_register(&fsl_ifc_ctrl_driver); +} +subsys_initcall(fsl_ifc_init); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Freescale Semiconductor"); +MODULE_DESCRIPTION("Freescale Integrated Flash Controller driver"); diff --git a/drivers/memory/mvebu-devbus.c b/drivers/memory/mvebu-devbus.c new file mode 100644 index 00000000000..ff7138fd66d --- /dev/null +++ b/drivers/memory/mvebu-devbus.c @@ -0,0 +1,362 @@ +/* + * Marvell EBU SoC Device Bus Controller + * (memory controller for NOR/NAND/SRAM/FPGA devices) + * + * Copyright (C) 2013-2014 Marvell + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation version 2 of the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + * + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/slab.h> +#include <linux/err.h> +#include <linux/io.h> +#include <linux/clk.h> +#include <linux/mbus.h> +#include <linux/of_platform.h> +#include <linux/of_address.h> +#include <linux/platform_device.h> + +/* Register definitions */ +#define ARMADA_DEV_WIDTH_SHIFT 30 +#define ARMADA_BADR_SKEW_SHIFT 28 +#define ARMADA_RD_HOLD_SHIFT 23 +#define ARMADA_ACC_NEXT_SHIFT 17 +#define ARMADA_RD_SETUP_SHIFT 12 +#define ARMADA_ACC_FIRST_SHIFT 6 + +#define ARMADA_SYNC_ENABLE_SHIFT 24 +#define ARMADA_WR_HIGH_SHIFT 16 +#define ARMADA_WR_LOW_SHIFT 8 + +#define ARMADA_READ_PARAM_OFFSET 0x0 +#define ARMADA_WRITE_PARAM_OFFSET 0x4 + +#define ORION_RESERVED (0x2 << 30) +#define ORION_BADR_SKEW_SHIFT 28 +#define ORION_WR_HIGH_EXT_BIT BIT(27) +#define ORION_WR_HIGH_EXT_MASK 0x8 +#define ORION_WR_LOW_EXT_BIT BIT(26) +#define ORION_WR_LOW_EXT_MASK 0x8 +#define ORION_ALE_WR_EXT_BIT BIT(25) +#define ORION_ALE_WR_EXT_MASK 0x8 +#define ORION_ACC_NEXT_EXT_BIT BIT(24) +#define ORION_ACC_NEXT_EXT_MASK 0x10 +#define ORION_ACC_FIRST_EXT_BIT BIT(23) +#define ORION_ACC_FIRST_EXT_MASK 0x10 +#define ORION_TURN_OFF_EXT_BIT BIT(22) +#define ORION_TURN_OFF_EXT_MASK 0x8 +#define ORION_DEV_WIDTH_SHIFT 20 +#define ORION_WR_HIGH_SHIFT 17 +#define ORION_WR_HIGH_MASK 0x7 +#define ORION_WR_LOW_SHIFT 14 +#define ORION_WR_LOW_MASK 0x7 +#define ORION_ALE_WR_SHIFT 11 +#define ORION_ALE_WR_MASK 0x7 +#define ORION_ACC_NEXT_SHIFT 7 +#define ORION_ACC_NEXT_MASK 0xF +#define ORION_ACC_FIRST_SHIFT 3 +#define ORION_ACC_FIRST_MASK 0xF +#define ORION_TURN_OFF_SHIFT 0 +#define ORION_TURN_OFF_MASK 0x7 + +struct devbus_read_params { + u32 bus_width; + u32 badr_skew; + u32 turn_off; + u32 acc_first; + u32 acc_next; + u32 rd_setup; + u32 rd_hold; +}; + +struct devbus_write_params { + u32 sync_enable; + u32 wr_high; + u32 wr_low; + u32 ale_wr; +}; + +struct devbus { + struct device *dev; + void __iomem *base; + unsigned long tick_ps; +}; + +static int get_timing_param_ps(struct devbus *devbus, + struct device_node *node, + const char *name, + u32 *ticks) +{ + u32 time_ps; + int err; + + err = of_property_read_u32(node, name, &time_ps); + if (err < 0) { + dev_err(devbus->dev, "%s has no '%s' property\n", + name, node->full_name); + return err; + } + + *ticks = (time_ps + devbus->tick_ps - 1) / devbus->tick_ps; + + dev_dbg(devbus->dev, "%s: %u ps -> 0x%x\n", + name, time_ps, *ticks); + return 0; +} + +static int devbus_get_timing_params(struct devbus *devbus, + struct device_node *node, + struct devbus_read_params *r, + struct devbus_write_params *w) +{ + int err; + + err = of_property_read_u32(node, "devbus,bus-width", &r->bus_width); + if (err < 0) { + dev_err(devbus->dev, + "%s has no 'devbus,bus-width' property\n", + node->full_name); + return err; + } + + /* + * The bus width is encoded into the register as 0 for 8 bits, + * and 1 for 16 bits, so we do the necessary conversion here. + */ + if (r->bus_width == 8) + r->bus_width = 0; + else if (r->bus_width == 16) + r->bus_width = 1; + else { + dev_err(devbus->dev, "invalid bus width %d\n", r->bus_width); + return -EINVAL; + } + + err = get_timing_param_ps(devbus, node, "devbus,badr-skew-ps", + &r->badr_skew); + if (err < 0) + return err; + + err = get_timing_param_ps(devbus, node, "devbus,turn-off-ps", + &r->turn_off); + if (err < 0) + return err; + + err = get_timing_param_ps(devbus, node, "devbus,acc-first-ps", + &r->acc_first); + if (err < 0) + return err; + + err = get_timing_param_ps(devbus, node, "devbus,acc-next-ps", + &r->acc_next); + if (err < 0) + return err; + + if (of_device_is_compatible(devbus->dev->of_node, "marvell,mvebu-devbus")) { + err = get_timing_param_ps(devbus, node, "devbus,rd-setup-ps", + &r->rd_setup); + if (err < 0) + return err; + + err = get_timing_param_ps(devbus, node, "devbus,rd-hold-ps", + &r->rd_hold); + if (err < 0) + return err; + + err = of_property_read_u32(node, "devbus,sync-enable", + &w->sync_enable); + if (err < 0) { + dev_err(devbus->dev, + "%s has no 'devbus,sync-enable' property\n", + node->full_name); + return err; + } + } + + err = get_timing_param_ps(devbus, node, "devbus,ale-wr-ps", + &w->ale_wr); + if (err < 0) + return err; + + err = get_timing_param_ps(devbus, node, "devbus,wr-low-ps", + &w->wr_low); + if (err < 0) + return err; + + err = get_timing_param_ps(devbus, node, "devbus,wr-high-ps", + &w->wr_high); + if (err < 0) + return err; + + return 0; +} + +static void devbus_orion_set_timing_params(struct devbus *devbus, + struct device_node *node, + struct devbus_read_params *r, + struct devbus_write_params *w) +{ + u32 value; + + /* + * The hardware designers found it would be a good idea to + * split most of the values in the register into two fields: + * one containing all the low-order bits, and another one + * containing just the high-order bit. For all of those + * fields, we have to split the value into these two parts. + */ + value = (r->turn_off & ORION_TURN_OFF_MASK) << ORION_TURN_OFF_SHIFT | + (r->acc_first & ORION_ACC_FIRST_MASK) << ORION_ACC_FIRST_SHIFT | + (r->acc_next & ORION_ACC_NEXT_MASK) << ORION_ACC_NEXT_SHIFT | + (w->ale_wr & ORION_ALE_WR_MASK) << ORION_ALE_WR_SHIFT | + (w->wr_low & ORION_WR_LOW_MASK) << ORION_WR_LOW_SHIFT | + (w->wr_high & ORION_WR_HIGH_MASK) << ORION_WR_HIGH_SHIFT | + r->bus_width << ORION_DEV_WIDTH_SHIFT | + ((r->turn_off & ORION_TURN_OFF_EXT_MASK) ? ORION_TURN_OFF_EXT_BIT : 0) | + ((r->acc_first & ORION_ACC_FIRST_EXT_MASK) ? ORION_ACC_FIRST_EXT_BIT : 0) | + ((r->acc_next & ORION_ACC_NEXT_EXT_MASK) ? ORION_ACC_NEXT_EXT_BIT : 0) | + ((w->ale_wr & ORION_ALE_WR_EXT_MASK) ? ORION_ALE_WR_EXT_BIT : 0) | + ((w->wr_low & ORION_WR_LOW_EXT_MASK) ? ORION_WR_LOW_EXT_BIT : 0) | + ((w->wr_high & ORION_WR_HIGH_EXT_MASK) ? ORION_WR_HIGH_EXT_BIT : 0) | + (r->badr_skew << ORION_BADR_SKEW_SHIFT) | + ORION_RESERVED; + + writel(value, devbus->base); +} + +static void devbus_armada_set_timing_params(struct devbus *devbus, + struct device_node *node, + struct devbus_read_params *r, + struct devbus_write_params *w) +{ + u32 value; + + /* Set read timings */ + value = r->bus_width << ARMADA_DEV_WIDTH_SHIFT | + r->badr_skew << ARMADA_BADR_SKEW_SHIFT | + r->rd_hold << ARMADA_RD_HOLD_SHIFT | + r->acc_next << ARMADA_ACC_NEXT_SHIFT | + r->rd_setup << ARMADA_RD_SETUP_SHIFT | + r->acc_first << ARMADA_ACC_FIRST_SHIFT | + r->turn_off; + + dev_dbg(devbus->dev, "read parameters register 0x%p = 0x%x\n", + devbus->base + ARMADA_READ_PARAM_OFFSET, + value); + + writel(value, devbus->base + ARMADA_READ_PARAM_OFFSET); + + /* Set write timings */ + value = w->sync_enable << ARMADA_SYNC_ENABLE_SHIFT | + w->wr_low << ARMADA_WR_LOW_SHIFT | + w->wr_high << ARMADA_WR_HIGH_SHIFT | + w->ale_wr; + + dev_dbg(devbus->dev, "write parameters register: 0x%p = 0x%x\n", + devbus->base + ARMADA_WRITE_PARAM_OFFSET, + value); + + writel(value, devbus->base + ARMADA_WRITE_PARAM_OFFSET); +} + +static int mvebu_devbus_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct device_node *node = pdev->dev.of_node; + struct devbus_read_params r; + struct devbus_write_params w; + struct devbus *devbus; + struct resource *res; + struct clk *clk; + unsigned long rate; + int err; + + devbus = devm_kzalloc(&pdev->dev, sizeof(struct devbus), GFP_KERNEL); + if (!devbus) + return -ENOMEM; + + devbus->dev = dev; + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + devbus->base = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(devbus->base)) + return PTR_ERR(devbus->base); + + clk = devm_clk_get(&pdev->dev, NULL); + if (IS_ERR(clk)) + return PTR_ERR(clk); + clk_prepare_enable(clk); + + /* + * Obtain clock period in picoseconds, + * we need this in order to convert timing + * parameters from cycles to picoseconds. + */ + rate = clk_get_rate(clk) / 1000; + devbus->tick_ps = 1000000000 / rate; + + dev_dbg(devbus->dev, "Setting timing parameter, tick is %lu ps\n", + devbus->tick_ps); + + if (!of_property_read_bool(node, "devbus,keep-config")) { + /* Read the Device Tree node */ + err = devbus_get_timing_params(devbus, node, &r, &w); + if (err < 0) + return err; + + /* Set the new timing parameters */ + if (of_device_is_compatible(node, "marvell,orion-devbus")) + devbus_orion_set_timing_params(devbus, node, &r, &w); + else + devbus_armada_set_timing_params(devbus, node, &r, &w); + } + + /* + * We need to create a child device explicitly from here to + * guarantee that the child will be probed after the timing + * parameters for the bus are written. + */ + err = of_platform_populate(node, NULL, NULL, dev); + if (err < 0) + return err; + + return 0; +} + +static const struct of_device_id mvebu_devbus_of_match[] = { + { .compatible = "marvell,mvebu-devbus" }, + { .compatible = "marvell,orion-devbus" }, + {}, +}; +MODULE_DEVICE_TABLE(of, mvebu_devbus_of_match); + +static struct platform_driver mvebu_devbus_driver = { + .probe = mvebu_devbus_probe, + .driver = { + .name = "mvebu-devbus", + .owner = THIS_MODULE, + .of_match_table = mvebu_devbus_of_match, + }, +}; + +static int __init mvebu_devbus_init(void) +{ + return platform_driver_register(&mvebu_devbus_driver); +} +module_init(mvebu_devbus_init); + +MODULE_LICENSE("GPL v2"); +MODULE_AUTHOR("Ezequiel Garcia <ezequiel.garcia@free-electrons.com>"); +MODULE_DESCRIPTION("Marvell EBU SoC Device Bus controller"); diff --git a/drivers/memory/tegra20-mc.c b/drivers/memory/tegra20-mc.c index 186f27d9e5f..7cd82b874ab 100644 --- a/drivers/memory/tegra20-mc.c +++ b/drivers/memory/tegra20-mc.c @@ -17,6 +17,7 @@ * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. */ +#include <linux/err.h> #include <linux/kernel.h> #include <linux/module.h> #include <linux/ratelimit.h> @@ -192,8 +193,11 @@ static irqreturn_t tegra20_mc_isr(int irq, void *data) mask &= stat; if (!mask) return IRQ_NONE; - while ((bit = ffs(mask)) != 0) + while ((bit = ffs(mask)) != 0) { tegra20_mc_decode(mc, bit - 1); + mask &= ~BIT(bit - 1); + } + mc_writel(mc, stat, MC_INTSTATUS); return IRQ_HANDLED; } @@ -214,11 +218,9 @@ static int tegra20_mc_probe(struct platform_device *pdev) struct resource *res; res = platform_get_resource(pdev, IORESOURCE_MEM, i); - if (!res) - return -ENODEV; - mc->regs[i] = devm_request_and_ioremap(&pdev->dev, res); - if (!mc->regs[i]) - return -EBUSY; + mc->regs[i] = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(mc->regs[i])) + return PTR_ERR(mc->regs[i]); } irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0); diff --git a/drivers/memory/tegra30-mc.c b/drivers/memory/tegra30-mc.c index 0b7ab9332a1..ef7934535fd 100644 --- a/drivers/memory/tegra30-mc.c +++ b/drivers/memory/tegra30-mc.c @@ -17,6 +17,7 @@ * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. */ +#include <linux/err.h> #include <linux/kernel.h> #include <linux/module.h> #include <linux/ratelimit.h> @@ -217,7 +218,7 @@ static void tegra30_mc_decode(struct tegra30_mc *mc, int n) return; } - err = readl(mc + MC_ERR_STATUS); + err = mc_readl(mc, MC_ERR_STATUS); type = (err & MC_ERR_TYPE_MASK) >> MC_ERR_TYPE_SHIFT; perm = (err & MC_ERR_INVALID_SMMU_PAGE_MASK) >> @@ -234,7 +235,7 @@ static void tegra30_mc_decode(struct tegra30_mc *mc, int n) if (cid < ARRAY_SIZE(tegra30_mc_client)) client = tegra30_mc_client[cid]; - addr = readl(mc + MC_ERR_ADR); + addr = mc_readl(mc, MC_ERR_ADR); dev_err_ratelimited(mc->dev, "%s (0x%08x): 0x%08x %s (%s %s %s %s)\n", mc_int_err[idx], err, addr, client, @@ -267,6 +268,7 @@ static const u32 tegra30_mc_ctx[] = { MC_INTMASK, }; +#ifdef CONFIG_PM static int tegra30_mc_suspend(struct device *dev) { int i; @@ -290,6 +292,7 @@ static int tegra30_mc_resume(struct device *dev) mc_readl(mc, MC_TIMING_CONTROL); return 0; } +#endif static UNIVERSAL_DEV_PM_OPS(tegra30_mc_pm, tegra30_mc_suspend, @@ -310,8 +313,11 @@ static irqreturn_t tegra30_mc_isr(int irq, void *data) mask &= stat; if (!mask) return IRQ_NONE; - while ((bit = ffs(mask)) != 0) + while ((bit = ffs(mask)) != 0) { tegra30_mc_decode(mc, bit - 1); + mask &= ~BIT(bit - 1); + } + mc_writel(mc, stat, MC_INTSTATUS); return IRQ_HANDLED; } @@ -334,11 +340,9 @@ static int tegra30_mc_probe(struct platform_device *pdev) struct resource *res; res = platform_get_resource(pdev, IORESOURCE_MEM, i); - if (!res) - return -ENODEV; - mc->regs[i] = devm_request_and_ioremap(&pdev->dev, res); - if (!mc->regs[i]) - return -EBUSY; + mc->regs[i] = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(mc->regs[i])) + return PTR_ERR(mc->regs[i]); } irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0); diff --git a/drivers/memory/ti-aemif.c b/drivers/memory/ti-aemif.c new file mode 100644 index 00000000000..d3df7602f40 --- /dev/null +++ b/drivers/memory/ti-aemif.c @@ -0,0 +1,427 @@ +/* + * TI AEMIF driver + * + * Copyright (C) 2010 - 2013 Texas Instruments Incorporated. http://www.ti.com/ + * + * Authors: + * Murali Karicheri <m-karicheri2@ti.com> + * Ivan Khoronzhuk <ivan.khoronzhuk@ti.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/clk.h> +#include <linux/err.h> +#include <linux/io.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_platform.h> +#include <linux/platform_device.h> + +#define TA_SHIFT 2 +#define RHOLD_SHIFT 4 +#define RSTROBE_SHIFT 7 +#define RSETUP_SHIFT 13 +#define WHOLD_SHIFT 17 +#define WSTROBE_SHIFT 20 +#define WSETUP_SHIFT 26 +#define EW_SHIFT 30 +#define SS_SHIFT 31 + +#define TA(x) ((x) << TA_SHIFT) +#define RHOLD(x) ((x) << RHOLD_SHIFT) +#define RSTROBE(x) ((x) << RSTROBE_SHIFT) +#define RSETUP(x) ((x) << RSETUP_SHIFT) +#define WHOLD(x) ((x) << WHOLD_SHIFT) +#define WSTROBE(x) ((x) << WSTROBE_SHIFT) +#define WSETUP(x) ((x) << WSETUP_SHIFT) +#define EW(x) ((x) << EW_SHIFT) +#define SS(x) ((x) << SS_SHIFT) + +#define ASIZE_MAX 0x1 +#define TA_MAX 0x3 +#define RHOLD_MAX 0x7 +#define RSTROBE_MAX 0x3f +#define RSETUP_MAX 0xf +#define WHOLD_MAX 0x7 +#define WSTROBE_MAX 0x3f +#define WSETUP_MAX 0xf +#define EW_MAX 0x1 +#define SS_MAX 0x1 +#define NUM_CS 4 + +#define TA_VAL(x) (((x) & TA(TA_MAX)) >> TA_SHIFT) +#define RHOLD_VAL(x) (((x) & RHOLD(RHOLD_MAX)) >> RHOLD_SHIFT) +#define RSTROBE_VAL(x) (((x) & RSTROBE(RSTROBE_MAX)) >> RSTROBE_SHIFT) +#define RSETUP_VAL(x) (((x) & RSETUP(RSETUP_MAX)) >> RSETUP_SHIFT) +#define WHOLD_VAL(x) (((x) & WHOLD(WHOLD_MAX)) >> WHOLD_SHIFT) +#define WSTROBE_VAL(x) (((x) & WSTROBE(WSTROBE_MAX)) >> WSTROBE_SHIFT) +#define WSETUP_VAL(x) (((x) & WSETUP(WSETUP_MAX)) >> WSETUP_SHIFT) +#define EW_VAL(x) (((x) & EW(EW_MAX)) >> EW_SHIFT) +#define SS_VAL(x) (((x) & SS(SS_MAX)) >> SS_SHIFT) + +#define NRCSR_OFFSET 0x00 +#define AWCCR_OFFSET 0x04 +#define A1CR_OFFSET 0x10 + +#define ACR_ASIZE_MASK 0x3 +#define ACR_EW_MASK BIT(30) +#define ACR_SS_MASK BIT(31) +#define ASIZE_16BIT 1 + +#define CONFIG_MASK (TA(TA_MAX) | \ + RHOLD(RHOLD_MAX) | \ + RSTROBE(RSTROBE_MAX) | \ + RSETUP(RSETUP_MAX) | \ + WHOLD(WHOLD_MAX) | \ + WSTROBE(WSTROBE_MAX) | \ + WSETUP(WSETUP_MAX) | \ + EW(EW_MAX) | SS(SS_MAX) | \ + ASIZE_MAX) + +/** + * struct aemif_cs_data: structure to hold cs parameters + * @cs: chip-select number + * @wstrobe: write strobe width, ns + * @rstrobe: read strobe width, ns + * @wsetup: write setup width, ns + * @whold: write hold width, ns + * @rsetup: read setup width, ns + * @rhold: read hold width, ns + * @ta: minimum turn around time, ns + * @enable_ss: enable/disable select strobe mode + * @enable_ew: enable/disable extended wait mode + * @asize: width of the asynchronous device's data bus + */ +struct aemif_cs_data { + u8 cs; + u16 wstrobe; + u16 rstrobe; + u8 wsetup; + u8 whold; + u8 rsetup; + u8 rhold; + u8 ta; + u8 enable_ss; + u8 enable_ew; + u8 asize; +}; + +/** + * struct aemif_device: structure to hold device data + * @base: base address of AEMIF registers + * @clk: source clock + * @clk_rate: clock's rate in kHz + * @num_cs: number of assigned chip-selects + * @cs_offset: start number of cs nodes + * @cs_data: array of chip-select settings + */ +struct aemif_device { + void __iomem *base; + struct clk *clk; + unsigned long clk_rate; + u8 num_cs; + int cs_offset; + struct aemif_cs_data cs_data[NUM_CS]; +}; + +/** + * aemif_calc_rate - calculate timing data. + * @pdev: platform device to calculate for + * @wanted: The cycle time needed in nanoseconds. + * @clk: The input clock rate in kHz. + * @max: The maximum divider value that can be programmed. + * + * On success, returns the calculated timing value minus 1 for easy + * programming into AEMIF timing registers, else negative errno. + */ +static int aemif_calc_rate(struct platform_device *pdev, int wanted, + unsigned long clk, int max) +{ + int result; + + result = DIV_ROUND_UP((wanted * clk), NSEC_PER_MSEC) - 1; + + dev_dbg(&pdev->dev, "%s: result %d from %ld, %d\n", __func__, result, + clk, wanted); + + /* It is generally OK to have a more relaxed timing than requested... */ + if (result < 0) + result = 0; + + /* ... But configuring tighter timings is not an option. */ + else if (result > max) + result = -EINVAL; + + return result; +} + +/** + * aemif_config_abus - configure async bus parameters + * @pdev: platform device to configure for + * @csnum: aemif chip select number + * + * This function programs the given timing values (in real clock) into the + * AEMIF registers taking the AEMIF clock into account. + * + * This function does not use any locking while programming the AEMIF + * because it is expected that there is only one user of a given + * chip-select. + * + * Returns 0 on success, else negative errno. + */ +static int aemif_config_abus(struct platform_device *pdev, int csnum) +{ + struct aemif_device *aemif = platform_get_drvdata(pdev); + struct aemif_cs_data *data = &aemif->cs_data[csnum]; + int ta, rhold, rstrobe, rsetup, whold, wstrobe, wsetup; + unsigned long clk_rate = aemif->clk_rate; + unsigned offset; + u32 set, val; + + offset = A1CR_OFFSET + (data->cs - aemif->cs_offset) * 4; + + ta = aemif_calc_rate(pdev, data->ta, clk_rate, TA_MAX); + rhold = aemif_calc_rate(pdev, data->rhold, clk_rate, RHOLD_MAX); + rstrobe = aemif_calc_rate(pdev, data->rstrobe, clk_rate, RSTROBE_MAX); + rsetup = aemif_calc_rate(pdev, data->rsetup, clk_rate, RSETUP_MAX); + whold = aemif_calc_rate(pdev, data->whold, clk_rate, WHOLD_MAX); + wstrobe = aemif_calc_rate(pdev, data->wstrobe, clk_rate, WSTROBE_MAX); + wsetup = aemif_calc_rate(pdev, data->wsetup, clk_rate, WSETUP_MAX); + + if (ta < 0 || rhold < 0 || rstrobe < 0 || rsetup < 0 || + whold < 0 || wstrobe < 0 || wsetup < 0) { + dev_err(&pdev->dev, "%s: cannot get suitable timings\n", + __func__); + return -EINVAL; + } + + set = TA(ta) | RHOLD(rhold) | RSTROBE(rstrobe) | RSETUP(rsetup) | + WHOLD(whold) | WSTROBE(wstrobe) | WSETUP(wsetup); + + set |= (data->asize & ACR_ASIZE_MASK); + if (data->enable_ew) + set |= ACR_EW_MASK; + if (data->enable_ss) + set |= ACR_SS_MASK; + + val = readl(aemif->base + offset); + val &= ~CONFIG_MASK; + val |= set; + writel(val, aemif->base + offset); + + return 0; +} + +static inline int aemif_cycles_to_nsec(int val, unsigned long clk_rate) +{ + return ((val + 1) * NSEC_PER_MSEC) / clk_rate; +} + +/** + * aemif_get_hw_params - function to read hw register values + * @pdev: platform device to read for + * @csnum: aemif chip select number + * + * This function reads the defaults from the registers and update + * the timing values. Required for get/set commands and also for + * the case when driver needs to use defaults in hardware. + */ +static void aemif_get_hw_params(struct platform_device *pdev, int csnum) +{ + struct aemif_device *aemif = platform_get_drvdata(pdev); + struct aemif_cs_data *data = &aemif->cs_data[csnum]; + unsigned long clk_rate = aemif->clk_rate; + u32 val, offset; + + offset = A1CR_OFFSET + (data->cs - aemif->cs_offset) * 4; + val = readl(aemif->base + offset); + + data->ta = aemif_cycles_to_nsec(TA_VAL(val), clk_rate); + data->rhold = aemif_cycles_to_nsec(RHOLD_VAL(val), clk_rate); + data->rstrobe = aemif_cycles_to_nsec(RSTROBE_VAL(val), clk_rate); + data->rsetup = aemif_cycles_to_nsec(RSETUP_VAL(val), clk_rate); + data->whold = aemif_cycles_to_nsec(WHOLD_VAL(val), clk_rate); + data->wstrobe = aemif_cycles_to_nsec(WSTROBE_VAL(val), clk_rate); + data->wsetup = aemif_cycles_to_nsec(WSETUP_VAL(val), clk_rate); + data->enable_ew = EW_VAL(val); + data->enable_ss = SS_VAL(val); + data->asize = val & ASIZE_MAX; +} + +/** + * of_aemif_parse_abus_config - parse CS configuration from DT + * @pdev: platform device to parse for + * @np: device node ptr + * + * This function update the emif async bus configuration based on the values + * configured in a cs device binding node. + */ +static int of_aemif_parse_abus_config(struct platform_device *pdev, + struct device_node *np) +{ + struct aemif_device *aemif = platform_get_drvdata(pdev); + struct aemif_cs_data *data; + u32 cs; + u32 val; + + if (of_property_read_u32(np, "ti,cs-chipselect", &cs)) { + dev_dbg(&pdev->dev, "cs property is required"); + return -EINVAL; + } + + if (cs - aemif->cs_offset >= NUM_CS || cs < aemif->cs_offset) { + dev_dbg(&pdev->dev, "cs number is incorrect %d", cs); + return -EINVAL; + } + + if (aemif->num_cs >= NUM_CS) { + dev_dbg(&pdev->dev, "cs count is more than %d", NUM_CS); + return -EINVAL; + } + + data = &aemif->cs_data[aemif->num_cs]; + data->cs = cs; + + /* read the current value in the hw register */ + aemif_get_hw_params(pdev, aemif->num_cs++); + + /* override the values from device node */ + if (!of_property_read_u32(np, "ti,cs-min-turnaround-ns", &val)) + data->ta = val; + + if (!of_property_read_u32(np, "ti,cs-read-hold-ns", &val)) + data->rhold = val; + + if (!of_property_read_u32(np, "ti,cs-read-strobe-ns", &val)) + data->rstrobe = val; + + if (!of_property_read_u32(np, "ti,cs-read-setup-ns", &val)) + data->rsetup = val; + + if (!of_property_read_u32(np, "ti,cs-write-hold-ns", &val)) + data->whold = val; + + if (!of_property_read_u32(np, "ti,cs-write-strobe-ns", &val)) + data->wstrobe = val; + + if (!of_property_read_u32(np, "ti,cs-write-setup-ns", &val)) + data->wsetup = val; + + if (!of_property_read_u32(np, "ti,cs-bus-width", &val)) + if (val == 16) + data->asize = 1; + data->enable_ew = of_property_read_bool(np, "ti,cs-extended-wait-mode"); + data->enable_ss = of_property_read_bool(np, "ti,cs-select-strobe-mode"); + return 0; +} + +static const struct of_device_id aemif_of_match[] = { + { .compatible = "ti,davinci-aemif", }, + { .compatible = "ti,da850-aemif", }, + {}, +}; + +static int aemif_probe(struct platform_device *pdev) +{ + int i; + int ret = -ENODEV; + struct resource *res; + struct device *dev = &pdev->dev; + struct device_node *np = dev->of_node; + struct device_node *child_np; + struct aemif_device *aemif; + + if (np == NULL) + return 0; + + aemif = devm_kzalloc(dev, sizeof(*aemif), GFP_KERNEL); + if (!aemif) + return -ENOMEM; + + platform_set_drvdata(pdev, aemif); + + aemif->clk = devm_clk_get(dev, NULL); + if (IS_ERR(aemif->clk)) { + dev_err(dev, "cannot get clock 'aemif'\n"); + return PTR_ERR(aemif->clk); + } + + clk_prepare_enable(aemif->clk); + aemif->clk_rate = clk_get_rate(aemif->clk) / MSEC_PER_SEC; + + if (of_device_is_compatible(np, "ti,da850-aemif")) + aemif->cs_offset = 2; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + aemif->base = devm_ioremap_resource(dev, res); + if (IS_ERR(aemif->base)) { + ret = PTR_ERR(aemif->base); + goto error; + } + + /* + * For every controller device node, there is a cs device node that + * describe the bus configuration parameters. This functions iterate + * over these nodes and update the cs data array. + */ + for_each_available_child_of_node(np, child_np) { + ret = of_aemif_parse_abus_config(pdev, child_np); + if (ret < 0) + goto error; + } + + for (i = 0; i < aemif->num_cs; i++) { + ret = aemif_config_abus(pdev, i); + if (ret < 0) { + dev_err(dev, "Error configuring chip select %d\n", + aemif->cs_data[i].cs); + goto error; + } + } + + /* + * Create a child devices explicitly from here to + * guarantee that the child will be probed after the AEMIF timing + * parameters are set. + */ + for_each_available_child_of_node(np, child_np) { + ret = of_platform_populate(child_np, NULL, NULL, dev); + if (ret < 0) + goto error; + } + + return 0; +error: + clk_disable_unprepare(aemif->clk); + return ret; +} + +static int aemif_remove(struct platform_device *pdev) +{ + struct aemif_device *aemif = platform_get_drvdata(pdev); + + clk_disable_unprepare(aemif->clk); + return 0; +} + +static struct platform_driver aemif_driver = { + .probe = aemif_probe, + .remove = aemif_remove, + .driver = { + .name = KBUILD_MODNAME, + .owner = THIS_MODULE, + .of_match_table = of_match_ptr(aemif_of_match), + }, +}; + +module_platform_driver(aemif_driver); + +MODULE_AUTHOR("Murali Karicheri <m-karicheri2@ti.com>"); +MODULE_AUTHOR("Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>"); +MODULE_DESCRIPTION("Texas Instruments AEMIF driver"); +MODULE_LICENSE("GPL v2"); +MODULE_ALIAS("platform:" KBUILD_MODNAME); |