diff options
Diffstat (limited to 'drivers/ide/pci/hpt366.c')
| -rw-r--r-- | drivers/ide/pci/hpt366.c | 1735 |
1 files changed, 0 insertions, 1735 deletions
diff --git a/drivers/ide/pci/hpt366.c b/drivers/ide/pci/hpt366.c deleted file mode 100644 index 127619a109e..00000000000 --- a/drivers/ide/pci/hpt366.c +++ /dev/null @@ -1,1735 +0,0 @@ -/* - * linux/drivers/ide/pci/hpt366.c Version 0.36 April 25, 2003 - * - * Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org> - * Portions Copyright (C) 2001 Sun Microsystems, Inc. - * Portions Copyright (C) 2003 Red Hat Inc - * - * Thanks to HighPoint Technologies for their assistance, and hardware. - * Special Thanks to Jon Burchmore in SanDiego for the deep pockets, his - * donation of an ABit BP6 mainboard, processor, and memory acellerated - * development and support. - * - * - * Highpoint have their own driver (source except for the raid part) - * available from http://www.highpoint-tech.com/hpt3xx-opensource-v131.tgz - * This may be useful to anyone wanting to work on the mainstream hpt IDE. - * - * Note that final HPT370 support was done by force extraction of GPL. - * - * - add function for getting/setting power status of drive - * - the HPT370's state machine can get confused. reset it before each dma - * xfer to prevent that from happening. - * - reset state engine whenever we get an error. - * - check for busmaster state at end of dma. - * - use new highpoint timings. - * - detect bus speed using highpoint register. - * - use pll if we don't have a clock table. added a 66MHz table that's - * just 2x the 33MHz table. - * - removed turnaround. NOTE: we never want to switch between pll and - * pci clocks as the chip can glitch in those cases. the highpoint - * approved workaround slows everything down too much to be useful. in - * addition, we would have to serialize access to each chip. - * Adrian Sun <a.sun@sun.com> - * - * add drive timings for 66MHz PCI bus, - * fix ATA Cable signal detection, fix incorrect /proc info - * add /proc display for per-drive PIO/DMA/UDMA mode and - * per-channel ATA-33/66 Cable detect. - * Duncan Laurie <void@sun.com> - * - * fixup /proc output for multiple controllers - * Tim Hockin <thockin@sun.com> - * - * On hpt366: - * Reset the hpt366 on error, reset on dma - * Fix disabling Fast Interrupt hpt366. - * Mike Waychison <crlf@sun.com> - * - * Added support for 372N clocking and clock switching. The 372N needs - * different clocks on read/write. This requires overloading rw_disk and - * other deeply crazy things. Thanks to <http://www.hoerstreich.de> for - * keeping me sane. - * Alan Cox <alan@redhat.com> - * - */ - - -#include <linux/config.h> -#include <linux/types.h> -#include <linux/module.h> -#include <linux/kernel.h> -#include <linux/delay.h> -#include <linux/timer.h> -#include <linux/mm.h> -#include <linux/ioport.h> -#include <linux/blkdev.h> -#include <linux/hdreg.h> - -#include <linux/interrupt.h> -#include <linux/pci.h> -#include <linux/init.h> -#include <linux/ide.h> - -#include <asm/uaccess.h> -#include <asm/io.h> -#include <asm/irq.h> - -/* various tuning parameters */ -#define HPT_RESET_STATE_ENGINE -#undef HPT_DELAY_INTERRUPT -#undef HPT_SERIALIZE_IO - -static const char *quirk_drives[] = { - "QUANTUM FIREBALLlct08 08", - "QUANTUM FIREBALLP KA6.4", - "QUANTUM FIREBALLP LM20.4", - "QUANTUM FIREBALLP LM20.5", - NULL -}; - -static const char *bad_ata100_5[] = { - "IBM-DTLA-307075", - "IBM-DTLA-307060", - "IBM-DTLA-307045", - "IBM-DTLA-307030", - "IBM-DTLA-307020", - "IBM-DTLA-307015", - "IBM-DTLA-305040", - "IBM-DTLA-305030", - "IBM-DTLA-305020", - "IC35L010AVER07-0", - "IC35L020AVER07-0", - "IC35L030AVER07-0", - "IC35L040AVER07-0", - "IC35L060AVER07-0", - "WDC AC310200R", - NULL -}; - -static const char *bad_ata66_4[] = { - "IBM-DTLA-307075", - "IBM-DTLA-307060", - "IBM-DTLA-307045", - "IBM-DTLA-307030", - "IBM-DTLA-307020", - "IBM-DTLA-307015", - "IBM-DTLA-305040", - "IBM-DTLA-305030", - "IBM-DTLA-305020", - "IC35L010AVER07-0", - "IC35L020AVER07-0", - "IC35L030AVER07-0", - "IC35L040AVER07-0", - "IC35L060AVER07-0", - "WDC AC310200R", - NULL -}; - -static const char *bad_ata66_3[] = { - "WDC AC310200R", - NULL -}; - -static const char *bad_ata33[] = { - "Maxtor 92720U8", "Maxtor 92040U6", "Maxtor 91360U4", "Maxtor 91020U3", "Maxtor 90845U3", "Maxtor 90650U2", - "Maxtor 91360D8", "Maxtor 91190D7", "Maxtor 91020D6", "Maxtor 90845D5", "Maxtor 90680D4", "Maxtor 90510D3", "Maxtor 90340D2", - "Maxtor 91152D8", "Maxtor 91008D7", "Maxtor 90845D6", "Maxtor 90840D6", "Maxtor 90720D5", "Maxtor 90648D5", "Maxtor 90576D4", - "Maxtor 90510D4", - "Maxtor 90432D3", "Maxtor 90288D2", "Maxtor 90256D2", - "Maxtor 91000D8", "Maxtor 90910D8", "Maxtor 90875D7", "Maxtor 90840D7", "Maxtor 90750D6", "Maxtor 90625D5", "Maxtor 90500D4", - "Maxtor 91728D8", "Maxtor 91512D7", "Maxtor 91303D6", "Maxtor 91080D5", "Maxtor 90845D4", "Maxtor 90680D4", "Maxtor 90648D3", "Maxtor 90432D2", - NULL -}; - -struct chipset_bus_clock_list_entry { - u8 xfer_speed; - unsigned int chipset_settings; -}; - -/* key for bus clock timings - * bit - * 0:3 data_high_time. inactive time of DIOW_/DIOR_ for PIO and MW - * DMA. cycles = value + 1 - * 4:8 data_low_time. active time of DIOW_/DIOR_ for PIO and MW - * DMA. cycles = value + 1 - * 9:12 cmd_high_time. inactive time of DIOW_/DIOR_ during task file - * register access. - * 13:17 cmd_low_time. active time of DIOW_/DIOR_ during task file - * register access. - * 18:21 udma_cycle_time. clock freq and clock cycles for UDMA xfer. - * during task file register access. - * 22:24 pre_high_time. time to initialize 1st cycle for PIO and MW DMA - * xfer. - * 25:27 cmd_pre_high_time. time to initialize 1st PIO cycle for task - * register access. - * 28 UDMA enable - * 29 DMA enable - * 30 PIO_MST enable. if set, the chip is in bus master mode during - * PIO. - * 31 FIFO enable. - */ -static struct chipset_bus_clock_list_entry forty_base_hpt366[] = { - { XFER_UDMA_4, 0x900fd943 }, - { XFER_UDMA_3, 0x900ad943 }, - { XFER_UDMA_2, 0x900bd943 }, - { XFER_UDMA_1, 0x9008d943 }, - { XFER_UDMA_0, 0x9008d943 }, - - { XFER_MW_DMA_2, 0xa008d943 }, - { XFER_MW_DMA_1, 0xa010d955 }, - { XFER_MW_DMA_0, 0xa010d9fc }, - - { XFER_PIO_4, 0xc008d963 }, - { XFER_PIO_3, 0xc010d974 }, - { XFER_PIO_2, 0xc010d997 }, - { XFER_PIO_1, 0xc010d9c7 }, - { XFER_PIO_0, 0xc018d9d9 }, - { 0, 0x0120d9d9 } -}; - -static struct chipset_bus_clock_list_entry thirty_three_base_hpt366[] = { - { XFER_UDMA_4, 0x90c9a731 }, - { XFER_UDMA_3, 0x90cfa731 }, - { XFER_UDMA_2, 0x90caa731 }, - { XFER_UDMA_1, 0x90cba731 }, - { XFER_UDMA_0, 0x90c8a731 }, - - { XFER_MW_DMA_2, 0xa0c8a731 }, - { XFER_MW_DMA_1, 0xa0c8a732 }, /* 0xa0c8a733 */ - { XFER_MW_DMA_0, 0xa0c8a797 }, - - { XFER_PIO_4, 0xc0c8a731 }, - { XFER_PIO_3, 0xc0c8a742 }, - { XFER_PIO_2, 0xc0d0a753 }, - { XFER_PIO_1, 0xc0d0a7a3 }, /* 0xc0d0a793 */ - { XFER_PIO_0, 0xc0d0a7aa }, /* 0xc0d0a7a7 */ - { 0, 0x0120a7a7 } -}; - -static struct chipset_bus_clock_list_entry twenty_five_base_hpt366[] = { - { XFER_UDMA_4, 0x90c98521 }, - { XFER_UDMA_3, 0x90cf8521 }, - { XFER_UDMA_2, 0x90cf8521 }, - { XFER_UDMA_1, 0x90cb8521 }, - { XFER_UDMA_0, 0x90cb8521 }, - - { XFER_MW_DMA_2, 0xa0ca8521 }, - { XFER_MW_DMA_1, 0xa0ca8532 }, - { XFER_MW_DMA_0, 0xa0ca8575 }, - - { XFER_PIO_4, 0xc0ca8521 }, - { XFER_PIO_3, 0xc0ca8532 }, - { XFER_PIO_2, 0xc0ca8542 }, - { XFER_PIO_1, 0xc0d08572 }, - { XFER_PIO_0, 0xc0d08585 }, - { 0, 0x01208585 } -}; - -/* from highpoint documentation. these are old values */ -static struct chipset_bus_clock_list_entry thirty_three_base_hpt370[] = { -/* { XFER_UDMA_5, 0x1A85F442, 0x16454e31 }, */ - { XFER_UDMA_5, 0x16454e31 }, - { XFER_UDMA_4, 0x16454e31 }, - { XFER_UDMA_3, 0x166d4e31 }, - { XFER_UDMA_2, 0x16494e31 }, - { XFER_UDMA_1, 0x164d4e31 }, - { XFER_UDMA_0, 0x16514e31 }, - - { XFER_MW_DMA_2, 0x26514e21 }, - { XFER_MW_DMA_1, 0x26514e33 }, - { XFER_MW_DMA_0, 0x26514e97 }, - - { XFER_PIO_4, 0x06514e21 }, - { XFER_PIO_3, 0x06514e22 }, - { XFER_PIO_2, 0x06514e33 }, - { XFER_PIO_1, 0x06914e43 }, - { XFER_PIO_0, 0x06914e57 }, - { 0, 0x06514e57 } -}; - -static struct chipset_bus_clock_list_entry sixty_six_base_hpt370[] = { - { XFER_UDMA_5, 0x14846231 }, - { XFER_UDMA_4, 0x14886231 }, - { XFER_UDMA_3, 0x148c6231 }, - { XFER_UDMA_2, 0x148c6231 }, - { XFER_UDMA_1, 0x14906231 }, - { XFER_UDMA_0, 0x14986231 }, - - { XFER_MW_DMA_2, 0x26514e21 }, - { XFER_MW_DMA_1, 0x26514e33 }, - { XFER_MW_DMA_0, 0x26514e97 }, - - { XFER_PIO_4, 0x06514e21 }, - { XFER_PIO_3, 0x06514e22 }, - { XFER_PIO_2, 0x06514e33 }, - { XFER_PIO_1, 0x06914e43 }, - { XFER_PIO_0, 0x06914e57 }, - { 0, 0x06514e57 } -}; - -/* these are the current (4 sep 2001) timings from highpoint */ -static struct chipset_bus_clock_list_entry thirty_three_base_hpt370a[] = { - { XFER_UDMA_5, 0x12446231 }, - { XFER_UDMA_4, 0x12446231 }, - { XFER_UDMA_3, 0x126c6231 }, - { XFER_UDMA_2, 0x12486231 }, - { XFER_UDMA_1, 0x124c6233 }, - { XFER_UDMA_0, 0x12506297 }, - - { XFER_MW_DMA_2, 0x22406c31 }, - { XFER_MW_DMA_1, 0x22406c33 }, - { XFER_MW_DMA_0, 0x22406c97 }, - - { XFER_PIO_4, 0x06414e31 }, - { XFER_PIO_3, 0x06414e42 }, - { XFER_PIO_2, 0x06414e53 }, - { XFER_PIO_1, 0x06814e93 }, - { XFER_PIO_0, 0x06814ea7 }, - { 0, 0x06814ea7 } -}; - -/* 2x 33MHz timings */ -static struct chipset_bus_clock_list_entry sixty_six_base_hpt370a[] = { - { XFER_UDMA_5, 0x1488e673 }, - { XFER_UDMA_4, 0x1488e673 }, - { XFER_UDMA_3, 0x1498e673 }, - { XFER_UDMA_2, 0x1490e673 }, - { XFER_UDMA_1, 0x1498e677 }, - { XFER_UDMA_0, 0x14a0e73f }, - - { XFER_MW_DMA_2, 0x2480fa73 }, - { XFER_MW_DMA_1, 0x2480fa77 }, - { XFER_MW_DMA_0, 0x2480fb3f }, - - { XFER_PIO_4, 0x0c82be73 }, - { XFER_PIO_3, 0x0c82be95 }, - { XFER_PIO_2, 0x0c82beb7 }, - { XFER_PIO_1, 0x0d02bf37 }, - { XFER_PIO_0, 0x0d02bf5f }, - { 0, 0x0d02bf5f } -}; - -static struct chipset_bus_clock_list_entry fifty_base_hpt370a[] = { - { XFER_UDMA_5, 0x12848242 }, - { XFER_UDMA_4, 0x12ac8242 }, - { XFER_UDMA_3, 0x128c8242 }, - { XFER_UDMA_2, 0x120c8242 }, - { XFER_UDMA_1, 0x12148254 }, - { XFER_UDMA_0, 0x121882ea }, - - { XFER_MW_DMA_2, 0x22808242 }, - { XFER_MW_DMA_1, 0x22808254 }, - { XFER_MW_DMA_0, 0x228082ea }, - - { XFER_PIO_4, 0x0a81f442 }, - { XFER_PIO_3, 0x0a81f443 }, - { XFER_PIO_2, 0x0a81f454 }, - { XFER_PIO_1, 0x0ac1f465 }, - { XFER_PIO_0, 0x0ac1f48a }, - { 0, 0x0ac1f48a } -}; - -static struct chipset_bus_clock_list_entry thirty_three_base_hpt372[] = { - { XFER_UDMA_6, 0x1c81dc62 }, - { XFER_UDMA_5, 0x1c6ddc62 }, - { XFER_UDMA_4, 0x1c8ddc62 }, - { XFER_UDMA_3, 0x1c8edc62 }, /* checkme */ - { XFER_UDMA_2, 0x1c91dc62 }, - { XFER_UDMA_1, 0x1c9adc62 }, /* checkme */ - { XFER_UDMA_0, 0x1c82dc62 }, /* checkme */ - - { XFER_MW_DMA_2, 0x2c829262 }, - { XFER_MW_DMA_1, 0x2c829266 }, /* checkme */ - { XFER_MW_DMA_0, 0x2c82922e }, /* checkme */ - - { XFER_PIO_4, 0x0c829c62 }, - { XFER_PIO_3, 0x0c829c84 }, - { XFER_PIO_2, 0x0c829ca6 }, - { XFER_PIO_1, 0x0d029d26 }, - { XFER_PIO_0, 0x0d029d5e }, - { 0, 0x0d029d5e } -}; - -static struct chipset_bus_clock_list_entry fifty_base_hpt372[] = { - { XFER_UDMA_5, 0x12848242 }, - { XFER_UDMA_4, 0x12ac8242 }, - { XFER_UDMA_3, 0x128c8242 }, - { XFER_UDMA_2, 0x120c8242 }, - { XFER_UDMA_1, 0x12148254 }, - { XFER_UDMA_0, 0x121882ea }, - - { XFER_MW_DMA_2, 0x22808242 }, - { XFER_MW_DMA_1, 0x22808254 }, - { XFER_MW_DMA_0, 0x228082ea }, - - { XFER_PIO_4, 0x0a81f442 }, - { XFER_PIO_3, 0x0a81f443 }, - { XFER_PIO_2, 0x0a81f454 }, - { XFER_PIO_1, 0x0ac1f465 }, - { XFER_PIO_0, 0x0ac1f48a }, - { 0, 0x0a81f443 } -}; - -static struct chipset_bus_clock_list_entry sixty_six_base_hpt372[] = { - { XFER_UDMA_6, 0x1c869c62 }, - { XFER_UDMA_5, 0x1cae9c62 }, - { XFER_UDMA_4, 0x1c8a9c62 }, - { XFER_UDMA_3, 0x1c8e9c62 }, - { XFER_UDMA_2, 0x1c929c62 }, - { XFER_UDMA_1, 0x1c9a9c62 }, - { XFER_UDMA_0, 0x1c829c62 }, - - { XFER_MW_DMA_2, 0x2c829c62 }, - { XFER_MW_DMA_1, 0x2c829c66 }, - { XFER_MW_DMA_0, 0x2c829d2e }, - - { XFER_PIO_4, 0x0c829c62 }, - { XFER_PIO_3, 0x0c829c84 }, - { XFER_PIO_2, 0x0c829ca6 }, - { XFER_PIO_1, 0x0d029d26 }, - { XFER_PIO_0, 0x0d029d5e }, - { 0, 0x0d029d26 } -}; - -static struct chipset_bus_clock_list_entry thirty_three_base_hpt374[] = { - { XFER_UDMA_6, 0x12808242 }, - { XFER_UDMA_5, 0x12848242 }, - { XFER_UDMA_4, 0x12ac8242 }, - { XFER_UDMA_3, 0x128c8242 }, - { XFER_UDMA_2, 0x120c8242 }, - { XFER_UDMA_1, 0x12148254 }, - { XFER_UDMA_0, 0x121882ea }, - - { XFER_MW_DMA_2, 0x22808242 }, - { XFER_MW_DMA_1, 0x22808254 }, - { XFER_MW_DMA_0, 0x228082ea }, - - { XFER_PIO_4, 0x0a81f442 }, - { XFER_PIO_3, 0x0a81f443 }, - { XFER_PIO_2, 0x0a81f454 }, - { XFER_PIO_1, 0x0ac1f465 }, - { XFER_PIO_0, 0x0ac1f48a }, - { 0, 0x06814e93 } -}; - -/* FIXME: 50MHz timings for HPT374 */ - -#if 0 -static struct chipset_bus_clock_list_entry sixty_six_base_hpt374[] = { - { XFER_UDMA_6, 0x12406231 }, /* checkme */ - { XFER_UDMA_5, 0x12446231 }, /* 0x14846231 */ - { XFER_UDMA_4, 0x16814ea7 }, /* 0x14886231 */ - { XFER_UDMA_3, 0x16814ea7 }, /* 0x148c6231 */ - { XFER_UDMA_2, 0x16814ea7 }, /* 0x148c6231 */ - { XFER_UDMA_1, 0x16814ea7 }, /* 0x14906231 */ - { XFER_UDMA_0, 0x16814ea7 }, /* 0x14986231 */ - { XFER_MW_DMA_2, 0x16814ea7 }, /* 0x26514e21 */ - { XFER_MW_DMA_1, 0x16814ea7 }, /* 0x26514e97 */ - { XFER_MW_DMA_0, 0x16814ea7 }, /* 0x26514e97 */ - { XFER_PIO_4, 0x06814ea7 }, /* 0x06514e21 */ - { XFER_PIO_3, 0x06814ea7 }, /* 0x06514e22 */ - { XFER_PIO_2, 0x06814ea7 }, /* 0x06514e33 */ - { XFER_PIO_1, 0x06814ea7 }, /* 0x06914e43 */ - { XFER_PIO_0, 0x06814ea7 }, /* 0x06914e57 */ - { 0, 0x06814ea7 } -}; -#endif - -#define HPT366_DEBUG_DRIVE_INFO 0 -#define HPT374_ALLOW_ATA133_6 0 -#define HPT371_ALLOW_ATA133_6 0 -#define HPT302_ALLOW_ATA133_6 0 -#define HPT372_ALLOW_ATA133_6 1 -#define HPT370_ALLOW_ATA100_5 1 -#define HPT366_ALLOW_ATA66_4 1 -#define HPT366_ALLOW_ATA66_3 1 -#define HPT366_MAX_DEVS 8 - -#define F_LOW_PCI_33 0x23 -#define F_LOW_PCI_40 0x29 -#define F_LOW_PCI_50 0x2d -#define F_LOW_PCI_66 0x42 - -/* - * Hold all the highpoint quirks and revision information in one - * place. - */ - -struct hpt_info -{ - u8 max_mode; /* Speeds allowed */ - int revision; /* Chipset revision */ - int flags; /* Chipset properties */ -#define PLL_MODE 1 -#define IS_372N 2 - /* Speed table */ - struct chipset_bus_clock_list_entry *speed; -}; - -/* - * This wants fixing so that we do everything not by classrev - * (which breaks on the newest chips) but by creating an - * enumeration of chip variants and using that - */ - -static __devinit u32 hpt_revision (struct pci_dev *dev) -{ - u32 class_rev; - pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev); - class_rev &= 0xff; - - switch(dev->device) { - /* Remap new 372N onto 372 */ - case PCI_DEVICE_ID_TTI_HPT372N: - class_rev = PCI_DEVICE_ID_TTI_HPT372; break; - case PCI_DEVICE_ID_TTI_HPT374: - class_rev = PCI_DEVICE_ID_TTI_HPT374; break; - case PCI_DEVICE_ID_TTI_HPT371: - class_rev = PCI_DEVICE_ID_TTI_HPT371; break; - case PCI_DEVICE_ID_TTI_HPT302: - class_rev = PCI_DEVICE_ID_TTI_HPT302; break; - case PCI_DEVICE_ID_TTI_HPT372: - class_rev = PCI_DEVICE_ID_TTI_HPT372; break; - default: - break; - } - return class_rev; -} - -static int check_in_drive_lists(ide_drive_t *drive, const char **list); - -static u8 hpt3xx_ratemask (ide_drive_t *drive) -{ - ide_hwif_t *hwif = drive->hwif; - struct hpt_info *info = ide_get_hwifdata(hwif); - u8 mode = 0; - - /* FIXME: TODO - move this to set info->mode once at boot */ - - if (info->revision >= 8) { /* HPT374 */ - mode = (HPT374_ALLOW_ATA133_6) ? 4 : 3; - } else if (info->revision >= 7) { /* HPT371 */ - mode = (HPT371_ALLOW_ATA133_6) ? 4 : 3; - } else if (info->revision >= 6) { /* HPT302 */ - mode = (HPT302_ALLOW_ATA133_6) ? 4 : 3; - } else if (info->revision >= 5) { /* HPT372 */ - mode = (HPT372_ALLOW_ATA133_6) ? 4 : 3; - } else if (info->revision >= 4) { /* HPT370A */ - mode = (HPT370_ALLOW_ATA100_5) ? 3 : 2; - } else if (info->revision >= 3) { /* HPT370 */ - mode = (HPT370_ALLOW_ATA100_5) ? 3 : 2; - mode = (check_in_drive_lists(drive, bad_ata33)) ? 0 : mode; - } else { /* HPT366 and HPT368 */ - mode = (check_in_drive_lists(drive, bad_ata33)) ? 0 : 2; - } - if (!eighty_ninty_three(drive) && mode) - mode = min(mode, (u8)1); - return mode; -} - -/* - * Note for the future; the SATA hpt37x we must set - * either PIO or UDMA modes 0,4,5 - */ - -static u8 hpt3xx_ratefilter (ide_drive_t *drive, u8 speed) -{ - ide_hwif_t *hwif = drive->hwif; - struct hpt_info *info = ide_get_hwifdata(hwif); - u8 mode = hpt3xx_ratemask(drive); - - if (drive->media != ide_disk) - return min(speed, (u8)XFER_PIO_4); - - switch(mode) { - case 0x04: - speed = min(speed, (u8)XFER_UDMA_6); - break; - case 0x03: - speed = min(speed, (u8)XFER_UDMA_5); - if (info->revision >= 5) - break; - if (check_in_drive_lists(drive, bad_ata100_5)) - speed = min(speed, (u8)XFER_UDMA_4); - break; - case 0x02: - speed = min(speed, (u8)XFER_UDMA_4); - /* - * CHECK ME, Does this need to be set to 5 ?? - */ - if (info->revision >= 3) - break; - if ((check_in_drive_lists(drive, bad_ata66_4)) || - (!(HPT366_ALLOW_ATA66_4))) - speed = min(speed, (u8)XFER_UDMA_3); - if ((check_in_drive_lists(drive, bad_ata66_3)) || - (!(HPT366_ALLOW_ATA66_3))) - speed = min(speed, (u8)XFER_UDMA_2); - break; - case 0x01: - speed = min(speed, (u8)XFER_UDMA_2); - /* - * CHECK ME, Does this need to be set to 5 ?? - */ - if (info->revision >= 3) - break; - if (check_in_drive_lists(drive, bad_ata33)) - speed = min(speed, (u8)XFER_MW_DMA_2); - break; - case 0x00: - default: - speed = min(speed, (u8)XFER_MW_DMA_2); - break; - } - return speed; -} - -static int check_in_drive_lists (ide_drive_t *drive, const char **list) -{ - struct hd_driveid *id = drive->id; - - if (quirk_drives == list) { - while (*list) - if (strstr(id->model, *list++)) - return 1; - } else { - while (*list) - if (!strcmp(*list++,id->model)) - return 1; - } - return 0; -} - -static unsigned int pci_bus_clock_list (u8 speed, struct chipset_bus_clock_list_entry * chipset_table) -{ - for ( ; chipset_table->xfer_speed ; chipset_table++) - if (chipset_table->xfer_speed == speed) - return chipset_table->chipset_settings; - return chipset_table->chipset_settings; -} - -static int hpt36x_tune_chipset(ide_drive_t *drive, u8 xferspeed) -{ - ide_hwif_t *hwif = drive->hwif; - struct pci_dev *dev = hwif->pci_dev; - struct hpt_info *info = ide_get_hwifdata(hwif); - u8 speed = hpt3xx_ratefilter(drive, xferspeed); - u8 regtime = (drive->select.b.unit & 0x01) ? 0x44 : 0x40; - u8 regfast = (hwif->channel) ? 0x55 : 0x51; - u8 drive_fast = 0; - u32 reg1 = 0, reg2 = 0; - - /* - * Disable the "fast interrupt" prediction. - */ - pci_read_config_byte(dev, regfast, &drive_fast); - if (drive_fast & 0x80) - pci_write_config_byte(dev, regfast, drive_fast & ~0x80); - - reg2 = pci_bus_clock_list(speed, info->speed); - - /* - * Disable on-chip PIO FIFO/buffer - * (to avoid problems handling I/O errors later) - */ - pci_read_config_dword(dev, regtime, ®1); - if (speed >= XFER_MW_DMA_0) { - reg2 = (reg2 & ~0xc0000000) | (reg1 & 0xc0000000); - } else { - reg2 = (reg2 & ~0x30070000) | (reg1 & 0x30070000); - } - reg2 &= ~0x80000000; - - pci_write_config_dword(dev, regtime, reg2); - - return ide_config_drive_speed(drive, speed); -} - -static int hpt370_tune_chipset(ide_drive_t *drive, u8 xferspeed) -{ - ide_hwif_t *hwif = drive->hwif; - struct pci_dev *dev = hwif->pci_dev; - struct hpt_info *info = ide_get_hwifdata(hwif); - u8 speed = hpt3xx_ratefilter(drive, xferspeed); - u8 regfast = (drive->hwif->channel) ? 0x55 : 0x51; - u8 drive_pci = 0x40 + (drive->dn * 4); - u8 new_fast = 0, drive_fast = 0; - u32 list_conf = 0, drive_conf = 0; - u32 conf_mask = (speed >= XFER_MW_DMA_0) ? 0xc0000000 : 0x30070000; - - /* - * Disable the "fast interrupt" prediction. - * don't holdoff on interrupts. (== 0x01 despite what the docs say) - */ - pci_read_config_byte(dev, regfast, &drive_fast); - new_fast = drive_fast; - if (new_fast & 0x02) - new_fast &= ~0x02; - -#ifdef HPT_DELAY_INTERRUPT - if (new_fast & 0x01) - new_fast &= ~0x01; -#else - if ((new_fast & 0x01) == 0) - new_fast |= 0x01; -#endif - if (new_fast != drive_fast) - pci_write_config_byte(dev, regfast, new_fast); - - list_conf = pci_bus_clock_list(speed, info->speed); - - pci_read_config_dword(dev, drive_pci, &drive_conf); - list_conf = (list_conf & ~conf_mask) | (drive_conf & conf_mask); - - if (speed < XFER_MW_DMA_0) - list_conf &= ~0x80000000; /* Disable on-chip PIO FIFO/buffer */ - pci_write_config_dword(dev, drive_pci, list_conf); - - return ide_config_drive_speed(drive, speed); -} - -static int hpt372_tune_chipset(ide_drive_t *drive, u8 xferspeed) -{ - ide_hwif_t *hwif = drive->hwif; - struct pci_dev *dev = hwif->pci_dev; - struct hpt_info *info = ide_get_hwifdata(hwif); - u8 speed = hpt3xx_ratefilter(drive, xferspeed); - u8 regfast = (drive->hwif->channel) ? 0x55 : 0x51; - u8 drive_fast = 0, drive_pci = 0x40 + (drive->dn * 4); - u32 list_conf = 0, drive_conf = 0; - u32 conf_mask = (speed >= XFER_MW_DMA_0) ? 0xc0000000 : 0x30070000; - - /* - * Disable the "fast interrupt" prediction. - * don't holdoff on interrupts. (== 0x01 despite what the docs say) - */ - pci_read_config_byte(dev, regfast, &drive_fast); - drive_fast &= ~0x07; - pci_write_config_byte(dev, regfast, drive_fast); - - list_conf = pci_bus_clock_list(speed, info->speed); - pci_read_config_dword(dev, drive_pci, &drive_conf); - list_conf = (list_conf & ~conf_mask) | (drive_conf & conf_mask); - if (speed < XFER_MW_DMA_0) - list_conf &= ~0x80000000; /* Disable on-chip PIO FIFO/buffer */ - pci_write_config_dword(dev, drive_pci, list_conf); - - return ide_config_drive_speed(drive, speed); -} - -static int hpt3xx_tune_chipset (ide_drive_t *drive, u8 speed) -{ - ide_hwif_t *hwif = drive->hwif; - struct hpt_info *info = ide_get_hwifdata(hwif); - - if (info->revision >= 8) - return hpt372_tune_chipset(drive, speed); /* not a typo */ - else if (info->revision >= 5) - return hpt372_tune_chipset(drive, speed); - else if (info->revision >= 3) - return hpt370_tune_chipset(drive, speed); - else /* hpt368: hpt_minimum_revision(dev, 2) */ - return hpt36x_tune_chipset(drive, speed); -} - -static void hpt3xx_tune_drive (ide_drive_t *drive, u8 pio) -{ - pio = ide_get_best_pio_mode(drive, 255, pio, NULL); - (void) hpt3xx_tune_chipset(drive, (XFER_PIO_0 + pio)); -} - -/* - * This allows the configuration of ide_pci chipset registers - * for cards that learn about the drive's UDMA, DMA, PIO capabilities - * after the drive is reported by the OS. Initially for designed for - * HPT366 UDMA chipset by HighPoint|Triones Technologies, Inc. - * - * check_in_drive_lists(drive, bad_ata66_4) - * check_in_drive_lists(drive, bad_ata66_3) - * check_in_drive_lists(drive, bad_ata33) - * - */ -static int config_chipset_for_dma (ide_drive_t *drive) -{ - u8 speed = ide_dma_speed(drive, hpt3xx_ratemask(drive)); - ide_hwif_t *hwif = drive->hwif; - struct hpt_info *info = ide_get_hwifdata(hwif); - - if (!speed) - return 0; - - /* If we don't have any timings we can't do a lot */ - if (info->speed == NULL) - return 0; - - (void) hpt3xx_tune_chipset(drive, speed); - return ide_dma_enable(drive); -} - -static int hpt3xx_quirkproc (ide_drive_t *drive) -{ - return ((int) check_in_drive_lists(drive, quirk_drives)); -} - -static void hpt3xx_intrproc (ide_drive_t *drive) -{ - ide_hwif_t *hwif = drive->hwif; - - if (drive->quirk_list) - return; - /* drives in the quirk_list may not like intr setups/cleanups */ - hwif->OUTB(drive->ctl|2, IDE_CONTROL_REG); -} - -static void hpt3xx_maskproc (ide_drive_t *drive, int mask) -{ - ide_hwif_t *hwif = drive->hwif; - struct hpt_info *info = ide_get_hwifdata(hwif); - struct pci_dev *dev = hwif->pci_dev; - - if (drive->quirk_list) { - if (info->revision >= 3) { - u8 reg5a = 0; - pci_read_config_byte(dev, 0x5a, ®5a); - if (((reg5a & 0x10) >> 4) != mask) - pci_write_config_byte(dev, 0x5a, mask ? (reg5a | 0x10) : (reg5a & ~0x10)); - } else { - if (mask) { - disable_irq(hwif->irq); - } else { - enable_irq(hwif->irq); - } - } - } else { - if (IDE_CONTROL_REG) - hwif->OUTB(mask ? (drive->ctl | 2) : - (drive->ctl & ~2), - IDE_CONTROL_REG); - } -} - -static int hpt366_config_drive_xfer_rate (ide_drive_t *drive) -{ - ide_hwif_t *hwif = drive->hwif; - struct hd_driveid *id = drive->id; - - drive->init_speed = 0; - - if ((id->capability & 1) && drive->autodma) { - - if (ide_use_dma(drive)) { - if (config_chipset_for_dma(drive)) - return hwif->ide_dma_on(drive); - } - - goto fast_ata_pio; - - } else if ((id->capability & 8) || (id->field_valid & 2)) { -fast_ata_pio: - hpt3xx_tune_drive(drive, 5); - return hwif->ide_dma_off_quietly(drive); - } - /* IORDY not supported */ - return 0; -} - -/* - * This is specific to the HPT366 UDMA bios chipset - * by HighPoint|Triones Technologies, Inc. - */ -static int hpt366_ide_dma_lostirq (ide_drive_t *drive) -{ - struct pci_dev *dev = HWIF(drive)->pci_dev; - u8 reg50h = 0, reg52h = 0, reg5ah = 0; - - pci_read_config_byte(dev, 0x50, ®50h); - pci_read_config_byte(dev, 0x52, ®52h); - pci_read_config_byte(dev, 0x5a, ®5ah); - printk("%s: (%s) reg50h=0x%02x, reg52h=0x%02x, reg5ah=0x%02x\n", - drive->name, __FUNCTION__, reg50h, reg52h, reg5ah); - if (reg5ah & 0x10) - pci_write_config_byte(dev, 0x5a, reg5ah & ~0x10); - return __ide_dma_lostirq(drive); -} - -static void hpt370_clear_engine (ide_drive_t *drive) -{ - u8 regstate = HWIF(drive)->channel ? 0x54 : 0x50; - pci_write_config_byte(HWIF(drive)->pci_dev, regstate, 0x37); - udelay(10); -} - -static void hpt370_ide_dma_start(ide_drive_t *drive) -{ -#ifdef HPT_RESET_STATE_ENGINE - hpt370_clear_engine(drive); -#endif - ide_dma_start(drive); -} - -static int hpt370_ide_dma_end (ide_drive_t *drive) -{ - ide_hwif_t *hwif = HWIF(drive); - u8 dma_stat = hwif->INB(hwif->dma_status); - - if (dma_stat & 0x01) { - /* wait a little */ - udelay(20); - dma_stat = hwif->INB(hwif->dma_status); - } - if ((dma_stat & 0x01) != 0) - /* fallthrough */ - (void) HWIF(drive)->ide_dma_timeout(drive); - - return __ide_dma_end(drive); -} - -static void hpt370_lostirq_timeout (ide_drive_t *drive) -{ - ide_hwif_t *hwif = HWIF(drive); - u8 bfifo = 0, reginfo = hwif->channel ? 0x56 : 0x52; - u8 dma_stat = 0, dma_cmd = 0; - - pci_read_config_byte(HWIF(drive)->pci_dev, reginfo, &bfifo); - printk(KERN_DEBUG "%s: %d bytes in FIFO\n", drive->name, bfifo); - hpt370_clear_engine(drive); - /* get dma command mode */ - dma_cmd = hwif->INB(hwif->dma_command); - /* stop dma */ - hwif->OUTB(dma_cmd & ~0x1, hwif->dma_command); - dma_stat = hwif->INB(hwif->dma_status); - /* clear errors */ - hwif->OUTB(dma_stat | 0x6, hwif->dma_status); -} - -static int hpt370_ide_dma_timeout (ide_drive_t *drive) -{ - hpt370_lostirq_timeout(drive); - hpt370_clear_engine(drive); - return __ide_dma_timeout(drive); -} - -static int hpt370_ide_dma_lostirq (ide_drive_t *drive) -{ - hpt370_lostirq_timeout(drive); - hpt370_clear_engine(drive); - return __ide_dma_lostirq(drive); -} - -/* returns 1 if DMA IRQ issued, 0 otherwise */ -static int hpt374_ide_dma_test_irq(ide_drive_t *drive) -{ - ide_hwif_t *hwif = HWIF(drive); - u16 bfifo = 0; - u8 reginfo = hwif->channel ? 0x56 : 0x52; - u8 dma_stat; - - pci_read_config_word(hwif->pci_dev, reginfo, &bfifo); - if (bfifo & 0x1FF) { -// printk("%s: %d bytes in FIFO\n", drive->name, bfifo); - return 0; - } - - dma_stat = hwif->INB(hwif->dma_status); - /* return 1 if INTR asserted */ - if ((dma_stat & 4) == 4) - return 1; - - if (!drive->waiting_for_dma) - printk(KERN_WARNING "%s: (%s) called while not waiting\n", - drive->name, __FUNCTION__); - return 0; -} - -static int hpt374_ide_dma_end (ide_drive_t *drive) -{ - struct pci_dev *dev = HWIF(drive)->pci_dev; - ide_hwif_t *hwif = HWIF(drive); - u8 msc_stat = 0, mscreg = hwif->channel ? 0x54 : 0x50; - u8 bwsr_stat = 0, bwsr_mask = hwif->channel ? 0x02 : 0x01; - - pci_read_config_byte(dev, 0x6a, &bwsr_stat); - pci_read_config_byte(dev, mscreg, &msc_stat); - if ((bwsr_stat & bwsr_mask) == bwsr_mask) - pci_write_config_byte(dev, mscreg, msc_stat|0x30); - return __ide_dma_end(drive); -} - -/** - * hpt372n_set_clock - perform clock switching dance - * @drive: Drive to switch - * @mode: Switching mode (0x21 for write, 0x23 otherwise) - * - * Switch the DPLL clock on the HPT372N devices. This is a - * right mess. - */ - -static void hpt372n_set_clock(ide_drive_t *drive, int mode) -{ - ide_hwif_t *hwif = HWIF(drive); - - /* FIXME: should we check for DMA active and BUG() */ - /* Tristate the bus */ - outb(0x80, hwif->dma_base+0x73); - outb(0x80, hwif->dma_base+0x77); - - /* Switch clock and reset channels */ - outb(mode, hwif->dma_base+0x7B); - outb(0xC0, hwif->dma_base+0x79); - - /* Reset state machines */ - outb(0x37, hwif->dma_base+0x70); - outb(0x37, hwif->dma_base+0x74); - - /* Complete reset */ - outb(0x00, hwif->dma_base+0x79); - - /* Reconnect channels to bus */ - outb(0x00, hwif->dma_base+0x73); - outb(0x00, hwif->dma_base+0x77); -} - -/** - * hpt372n_rw_disk - prepare for I/O - * @drive: drive for command - * @rq: block request structure - * - * This is called when a disk I/O is issued to the 372N. - * We need it because of the clock switching. - */ - -static void hpt372n_rw_disk(ide_drive_t *drive, struct request *rq) -{ - ide_hwif_t *hwif = drive->hwif; - int wantclock; - - wantclock = rq_data_dir(rq) ? 0x23 : 0x21; - - if (hwif->config_data != wantclock) { - hpt372n_set_clock(drive, wantclock); - hwif->config_data = wantclock; - } -} - -/* - * Since SUN Cobalt is attempting to do this operation, I should disclose - * this has been a long time ago Thu Jul 27 16:40:57 2000 was the patch date - * HOTSWAP ATA Infrastructure. - */ - -static void hpt3xx_reset (ide_drive_t *drive) -{ -} - -static int hpt3xx_tristate (ide_drive_t * drive, int state) -{ - ide_hwif_t *hwif = HWIF(drive); - struct pci_dev *dev = hwif->pci_dev; - u8 reg59h = 0, reset = (hwif->channel) ? 0x80 : 0x40; - u8 regXXh = 0, state_reg= (hwif->channel) ? 0x57 : 0x53; - - pci_read_config_byte(dev, 0x59, ®59h); - pci_read_config_byte(dev, state_reg, ®XXh); - - if (state) { - (void) ide_do_reset(drive); - pci_write_config_byte(dev, state_reg, regXXh|0x80); - pci_write_config_byte(dev, 0x59, reg59h|reset); - } else { - pci_write_config_byte(dev, 0x59, reg59h & ~(reset)); - pci_write_config_byte(dev, state_reg, regXXh & ~(0x80)); - (void) ide_do_reset(drive); - } - return 0; -} - -/* - * set/get power state for a drive. - * turning the power off does the following things: - * 1) soft-reset the drive - * 2) tri-states the ide bus - * - * when we turn things back on, we need to re-initialize things. - */ -#define TRISTATE_BIT 0x8000 -static int hpt370_busproc(ide_drive_t * drive, int state) -{ - ide_hwif_t *hwif = drive->hwif; - struct pci_dev *dev = hwif->pci_dev; - u8 tristate = 0, resetmask = 0, bus_reg = 0; - u16 tri_reg; - - hwif->bus_state = state; - - if (hwif->channel) { - /* secondary channel */ - tristate = 0x56; - resetmask = 0x80; - } else { - /* primary channel */ - tristate = 0x52; - resetmask = 0x40; - } - - /* grab status */ - pci_read_config_word(dev, tristate, &tri_reg); - pci_read_config_byte(dev, 0x59, &bus_reg); - - /* set the state. we don't set it if we don't need to do so. - * make sure that the drive knows that it has failed if it's off */ - switch (state) { - case BUSSTATE_ON: - hwif->drives[0].failures = 0; - hwif->drives[1].failures = 0; - if ((bus_reg & resetmask) == 0) - return 0; - tri_reg &= ~TRISTATE_BIT; - bus_reg &= ~resetmask; - break; - case BUSSTATE_OFF: - hwif->drives[0].failures = hwif->drives[0].max_failures + 1; - hwif->drives[1].failures = hwif->drives[1].max_failures + 1; - if ((tri_reg & TRISTATE_BIT) == 0 && (bus_reg & resetmask)) - return 0; - tri_reg &= ~TRISTATE_BIT; - bus_reg |= resetmask; - break; - case BUSSTATE_TRISTATE: - hwif->drives[0].failures = hwif->drives[0].max_failures + 1; - hwif->drives[1].failures = hwif->drives[1].max_failures + 1; - if ((tri_reg & TRISTATE_BIT) && (bus_reg & resetmask)) - return 0; - tri_reg |= TRISTATE_BIT; - bus_reg |= resetmask; - break; - } - pci_write_config_byte(dev, 0x59, bus_reg); - pci_write_config_word(dev, tristate, tri_reg); - - return 0; -} - -static void __devinit hpt366_clocking(ide_hwif_t *hwif) -{ - u32 reg1 = 0; - struct hpt_info *info = ide_get_hwifdata(hwif); - - pci_read_config_dword(hwif->pci_dev, 0x40, ®1); - - /* detect bus speed by looking at control reg timing: */ - switch((reg1 >> 8) & 7) { - case 5: - info->speed = forty_base_hpt366; - break; - case 9: - info->speed = twenty_five_base_hpt366; - break; - case 7: - default: - info->speed = thirty_three_base_hpt366; - break; - } -} - -static void __devinit hpt37x_clocking(ide_hwif_t *hwif) -{ - struct hpt_info *info = ide_get_hwifdata(hwif); - struct pci_dev *dev = hwif->pci_dev; - int adjust, i; - u16 freq; - u32 pll; - u8 reg5bh; - - /* - * default to pci clock. make sure MA15/16 are set to output - * to prevent drives having problems with 40-pin cables. Needed - * for some drives such as IBM-DTLA which will not enter ready - * state on reset when PDIAG is a input. - * - * ToDo: should we set 0x21 when using PLL mode ? - */ - pci_write_config_byte(dev, 0x5b, 0x23); - - /* - * set up the PLL. we need to adjust it so that it's stable. - * freq = Tpll * 192 / Tpci - * - * Todo. For non x86 should probably check the dword is - * set to 0xABCDExxx indicating the BIOS saved f_CNT - */ - pci_read_config_word(dev, 0x78, &freq); - freq &= 0x1FF; - - /* - * The 372N uses different PCI clock information and has - * some other complications - * On PCI33 timing we must clock switch - * On PCI66 timing we must NOT use the PCI clock - * - * Currently we always set up the PLL for the 372N - */ - - if(info->flags & IS_372N) - { - printk(KERN_INFO "hpt: HPT372N detected, using 372N timing.\n"); - if(freq < 0x55) - pll = F_LOW_PCI_33; - else if(freq < 0x70) - pll = F_LOW_PCI_40; - else if(freq < 0x7F) - pll = F_LOW_PCI_50; - else - pll = F_LOW_PCI_66; - - printk(KERN_INFO "FREQ: %d PLL: %d\n", freq, pll); - - /* We always use the pll not the PCI clock on 372N */ - } - else - { - if(freq < 0x9C) - pll = F_LOW_PCI_33; - else if(freq < 0xb0) - pll = F_LOW_PCI_40; - else if(freq <0xc8) - pll = F_LOW_PCI_50; - else - pll = F_LOW_PCI_66; - - if (pll == F_LOW_PCI_33) { - if (info->revision >= 8) - info->speed = thirty_three_base_hpt374; - else if (info->revision >= 5) - info->speed = thirty_three_base_hpt372; - else if (info->revision >= 4) - info->speed = thirty_three_base_hpt370a; - else - info->speed = thirty_three_base_hpt370; - printk(KERN_DEBUG "HPT37X: using 33MHz PCI clock\n"); - } else if (pll == F_LOW_PCI_40) { - /* Unsupported */ - } else if (pll == F_LOW_PCI_50) { - if (info->revision >= 8) - info->speed = fifty_base_hpt370a; - else if (info->revision >= 5) - info->speed = fifty_base_hpt372; - else if (info->revision >= 4) - info->speed = fifty_base_hpt370a; - else - info->speed = fifty_base_hpt370a; - printk(KERN_DEBUG "HPT37X: using 50MHz PCI clock\n"); - } else { - if (info->revision >= 8) { - printk(KERN_ERR "HPT37x: 66MHz timings are not supported.\n"); - } - else if (info->revision >= 5) - info->speed = sixty_six_base_hpt372; - else if (info->revision >= 4) - info->speed = sixty_six_base_hpt370a; - else - info->speed = sixty_six_base_hpt370; - printk(KERN_DEBUG "HPT37X: using 66MHz PCI clock\n"); - } - } - - /* - * only try the pll if we don't have a table for the clock - * speed that we're running at. NOTE: the internal PLL will - * result in slow reads when using a 33MHz PCI clock. we also - * don't like to use the PLL because it will cause glitches - * on PRST/SRST when the HPT state engine gets reset. - * - * ToDo: Use 66MHz PLL when ATA133 devices are present on a - * 372 device so we can get ATA133 support - */ - if (info->speed) - goto init_hpt37X_done; - - info->flags |= PLL_MODE; - - /* - * FIXME: make this work correctly, esp with 372N as per - * reference driver code. - * - * adjust PLL based upon PCI clock, enable it, and wait for - * stabilization. - */ - adjust = 0; - freq = (pll < F_LOW_PCI_50) ? 2 : 4; - while (adjust++ < 6) { - pci_write_config_dword(dev, 0x5c, (freq + pll) << 16 | - pll | 0x100); - - /* wait for clock stabilization */ - for (i = 0; i < 0x50000; i++) { - pci_read_config_byte(dev, 0x5b, ®5bh); - if (reg5bh & 0x80) { - /* spin looking for the clock to destabilize */ - for (i = 0; i < 0x1000; ++i) { - pci_read_config_byte(dev, 0x5b, - ®5bh); - if ((reg5bh & 0x80) == 0) - goto pll_recal; - } - pci_read_config_dword(dev, 0x5c, &pll); - pci_write_config_dword(dev, 0x5c, - pll & ~0x100); - pci_write_config_byte(dev, 0x5b, 0x21); - if (info->revision >= 8) - info->speed = fifty_base_hpt370a; - else if (info->revision >= 5) - info->speed = fifty_base_hpt372; - else if (info->revision >= 4) - info->speed = fifty_base_hpt370a; - else - info->speed = fifty_base_hpt370a; - printk("HPT37X: using 50MHz internal PLL\n"); - goto init_hpt37X_done; - } - } -pll_recal: - if (adjust & 1) - pll -= (adjust >> 1); - else - pll += (adjust >> 1); - } - -init_hpt37X_done: - if (!info->speed) - printk(KERN_ERR "HPT37X%s: unknown bus timing [%d %d].\n", - (info->flags & IS_372N)?"N":"", pll, freq); - /* reset state engine */ - pci_write_config_byte(dev, 0x50, 0x37); - pci_write_config_byte(dev, 0x54, 0x37); - udelay(100); -} - -static int __devinit init_hpt37x(struct pci_dev *dev) -{ - u8 reg5ah; - - pci_read_config_byte(dev, 0x5a, ®5ah); - /* interrupt force enable */ - pci_write_config_byte(dev, 0x5a, (reg5ah & ~0x10)); - return 0; -} - -static int __devinit init_hpt366(struct pci_dev *dev) -{ - u32 reg1 = 0; - u8 drive_fast = 0; - - /* - * Disable the "fast interrupt" prediction. - */ - pci_read_config_byte(dev, 0x51, &drive_fast); - if (drive_fast & 0x80) - pci_write_config_byte(dev, 0x51, drive_fast & ~0x80); - pci_read_config_dword(dev, 0x40, ®1); - - return 0; -} - -static unsigned int __devinit init_chipset_hpt366(struct pci_dev *dev, const char *name) -{ - int ret = 0; - - /* - * FIXME: Not portable. Also, why do we enable the ROM in the first place? - * We don't seem to be using it. - */ - if (dev->resource[PCI_ROM_RESOURCE].start) - pci_write_config_dword(dev, PCI_ROM_ADDRESS, - dev->resource[PCI_ROM_RESOURCE].start | PCI_ROM_ADDRESS_ENABLE); - - pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4)); - pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78); - pci_write_config_byte(dev, PCI_MIN_GNT, 0x08); - pci_write_config_byte(dev, PCI_MAX_LAT, 0x08); - - if (hpt_revision(dev) >= 3) - ret = init_hpt37x(dev); - else - ret = init_hpt366(dev); - - if (ret) - return ret; - - return dev->irq; -} - -static void __devinit init_hwif_hpt366(ide_hwif_t *hwif) -{ - struct pci_dev *dev = hwif->pci_dev; - struct hpt_info *info = ide_get_hwifdata(hwif); - u8 ata66 = 0, regmask = (hwif->channel) ? 0x01 : 0x02; - - hwif->tuneproc = &hpt3xx_tune_drive; - hwif->speedproc = &hpt3xx_tune_chipset; - hwif->quirkproc = &hpt3xx_quirkproc; - hwif->intrproc = &hpt3xx_intrproc; - hwif->maskproc = &hpt3xx_maskproc; - - if(info->flags & IS_372N) - hwif->rw_disk = &hpt372n_rw_disk; - - /* - * The HPT37x uses the CBLID pins as outputs for MA15/MA16 - * address lines to access an external eeprom. To read valid - * cable detect state the pins must be enabled as inputs. - */ - if (info->revision >= 8 && (PCI_FUNC(dev->devfn) & 1)) { - /* - * HPT374 PCI function 1 - * - set bit 15 of reg 0x52 to enable TCBLID as input - * - set bit 15 of reg 0x56 to enable FCBLID as input - */ - u16 mcr3, mcr6; - pci_read_config_word(dev, 0x52, &mcr3); - pci_read_config_word(dev, 0x56, &mcr6); - pci_write_config_word(dev, 0x52, mcr3 | 0x8000); - pci_write_config_word(dev, 0x56, mcr6 | 0x8000); - /* now read cable id register */ - pci_read_config_byte(dev, 0x5a, &ata66); - pci_write_config_word(dev, 0x52, mcr3); - pci_write_config_word(dev, 0x56, mcr6); - } else if (info->revision >= 3) { - /* - * HPT370/372 and 374 pcifn 0 - * - clear bit 0 of 0x5b to enable P/SCBLID as inputs - */ - u8 scr2; - pci_read_config_byte(dev, 0x5b, &scr2); - pci_write_config_byte(dev, 0x5b, scr2 & ~1); - /* now read cable id register */ - pci_read_config_byte(dev, 0x5a, &ata66); - pci_write_config_byte(dev, 0x5b, scr2); - } else { - pci_read_config_byte(dev, 0x5a, &ata66); - } - -#ifdef DEBUG - printk("HPT366: reg5ah=0x%02x ATA-%s Cable Port%d\n", - ata66, (ata66 & regmask) ? "33" : "66", - PCI_FUNC(hwif->pci_dev->devfn)); -#endif /* DEBUG */ - -#ifdef HPT_SERIALIZE_IO - /* serialize access to this device */ - if (hwif->mate) - hwif->serialized = hwif->mate->serialized = 1; -#endif - - if (info->revision >= 3) { - u8 reg5ah = 0; - pci_write_config_byte(dev, 0x5a, reg5ah & ~0x10); - /* - * set up ioctl for power status. - * note: power affects both - * drives on each channel - */ - hwif->resetproc = &hpt3xx_reset; - hwif->busproc = &hpt370_busproc; - } else if (info->revision >= 2) { - hwif->resetproc = &hpt3xx_reset; - hwif->busproc = &hpt3xx_tristate; - } else { - hwif->resetproc = &hpt3xx_reset; - hwif->busproc = &hpt3xx_tristate; - } - - if (!hwif->dma_base) { - hwif->drives[0].autotune = 1; - hwif->drives[1].autotune = 1; - return; - } - - hwif->ultra_mask = 0x7f; - hwif->mwdma_mask = 0x07; - - if (!(hwif->udma_four)) - hwif->udma_four = ((ata66 & regmask) ? 0 : 1); - hwif->ide_dma_check = &hpt366_config_drive_xfer_rate; - - if (info->revision >= 8) { - hwif->ide_dma_test_irq = &hpt374_ide_dma_test_irq; - hwif->ide_dma_end = &hpt374_ide_dma_end; - } else if (info->revision >= 5) { - hwif->ide_dma_test_irq = &hpt374_ide_dma_test_irq; - hwif->ide_dma_end = &hpt374_ide_dma_end; - } else if (info->revision >= 3) { - hwif->dma_start = &hpt370_ide_dma_start; - hwif->ide_dma_end = &hpt370_ide_dma_end; - hwif->ide_dma_timeout = &hpt370_ide_dma_timeout; - hwif->ide_dma_lostirq = &hpt370_ide_dma_lostirq; - } else if (info->revision >= 2) - hwif->ide_dma_lostirq = &hpt366_ide_dma_lostirq; - else - hwif->ide_dma_lostirq = &hpt366_ide_dma_lostirq; - - if (!noautodma) - hwif->autodma = 1; - hwif->drives[0].autodma = hwif->autodma; - hwif->drives[1].autodma = hwif->autodma; -} - -static void __devinit init_dma_hpt366(ide_hwif_t *hwif, unsigned long dmabase) -{ - struct hpt_info *info = ide_get_hwifdata(hwif); - u8 masterdma = 0, slavedma = 0; - u8 dma_new = 0, dma_old = 0; - u8 primary = hwif->channel ? 0x4b : 0x43; - u8 secondary = hwif->channel ? 0x4f : 0x47; - unsigned long flags; - - if (!dmabase) - return; - - if(info->speed == NULL) { - printk(KERN_WARNING "hpt: no known IDE timings, disabling DMA.\n"); - return; - } - - dma_old = hwif->INB(dmabase+2); - - local_irq_save(flags); - - dma_new = dma_old; - pci_read_config_byte(hwif->pci_dev, primary, &masterdma); - pci_read_config_byte(hwif->pci_dev, secondary, &slavedma); - - if (masterdma & 0x30) dma_new |= 0x20; - if (slavedma & 0x30) dma_new |= 0x40; - if (dma_new != dma_old) - hwif->OUTB(dma_new, dmabase+2); - - local_irq_restore(flags); - - ide_setup_dma(hwif, dmabase, 8); -} - -/* - * We "borrow" this hook in order to set the data structures - * up early enough before dma or init_hwif calls are made. - */ - -static void __devinit init_iops_hpt366(ide_hwif_t *hwif) -{ - struct hpt_info *info = kmalloc(sizeof(struct hpt_info), GFP_KERNEL); - unsigned long dmabase = pci_resource_start(hwif->pci_dev, 4); - u8 did, rid; - - if(info == NULL) { - printk(KERN_WARNING "hpt366: out of memory.\n"); - return; - } - memset(info, 0, sizeof(struct hpt_info)); - ide_set_hwifdata(hwif, info); - - if(dmabase) { - did = inb(dmabase + 0x22); - rid = inb(dmabase + 0x28); - - if((did == 4 && rid == 6) || (did == 5 && rid > 1)) - info->flags |= IS_372N; - } - - info->revision = hpt_revision(hwif->pci_dev); - - if (info->revision >= 3) - hpt37x_clocking(hwif); - else - hpt366_clocking(hwif); -} - -static int __devinit init_setup_hpt374(struct pci_dev *dev, ide_pci_device_t *d) -{ - struct pci_dev *findev = NULL; - - if (PCI_FUNC(dev->devfn) & 1) - return -ENODEV; - - while ((findev = pci_find_device(PCI_ANY_ID, PCI_ANY_ID, findev)) != NULL) { - if ((findev->vendor == dev->vendor) && - (findev->device == dev->device) && - ((findev->devfn - dev->devfn) == 1) && - (PCI_FUNC(findev->devfn) & 1)) { - if (findev->irq != dev->irq) { - /* FIXME: we need a core pci_set_interrupt() */ - findev->irq = dev->irq; - printk(KERN_WARNING "%s: pci-config space interrupt " - "fixed.\n", d->name); - } - return ide_setup_pci_devices(dev, findev, d); - } - } - return ide_setup_pci_device(dev, d); -} - -static int __devinit init_setup_hpt37x(struct pci_dev *dev, ide_pci_device_t *d) -{ - return ide_setup_pci_device(dev, d); -} - -static int __devinit init_setup_hpt366(struct pci_dev *dev, ide_pci_device_t *d) -{ - struct pci_dev *findev = NULL; - u8 pin1 = 0, pin2 = 0; - unsigned int class_rev; - char *chipset_names[] = {"HPT366", "HPT366", "HPT368", - "HPT370", "HPT370A", "HPT372", - "HPT372N" }; - - if (PCI_FUNC(dev->devfn) & 1) - return -ENODEV; - - pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev); - class_rev &= 0xff; - - if(dev->device == PCI_DEVICE_ID_TTI_HPT372N) - class_rev = 6; - - if(class_rev <= 6) - d->name = chipset_names[class_rev]; - - switch(class_rev) { - case 6: - case 5: - case 4: - case 3: - goto init_single; - default: - break; - } - - d->channels = 1; - - pci_read_config_byte(dev, PCI_INTERRUPT_PIN, &pin1); - while ((findev = pci_find_device(PCI_ANY_ID, PCI_ANY_ID, findev)) != NULL) { - if ((findev->vendor == dev->vendor) && - (findev->device == dev->device) && - ((findev->devfn - dev->devfn) == 1) && - (PCI_FUNC(findev->devfn) & 1)) { - pci_read_config_byte(findev, PCI_INTERRUPT_PIN, &pin2); - if ((pin1 != pin2) && (dev->irq == findev->irq)) { - d->bootable = ON_BOARD; - printk("%s: onboard version of chipset, " - "pin1=%d pin2=%d\n", d->name, - pin1, pin2); - } - return ide_setup_pci_devices(dev, findev, d); - } - } -init_single: - return ide_setup_pci_device(dev, d); -} - -static ide_pci_device_t hpt366_chipsets[] __devinitdata = { - { /* 0 */ - .name = "HPT366", - .init_setup = init_setup_hpt366, - .init_chipset = init_chipset_hpt366, - .init_iops = init_iops_hpt366, - .init_hwif = init_hwif_hpt366, - .init_dma = init_dma_hpt366, - .channels = 2, - .autodma = AUTODMA, - .bootable = OFF_BOARD, - .extra = 240 - },{ /* 1 */ - .name = "HPT372A", - .init_setup = init_setup_hpt37x, - .init_chipset = init_chipset_hpt366, - .init_iops = init_iops_hpt366, - .init_hwif = init_hwif_hpt366, - .init_dma = init_dma_hpt366, - .channels = 2, - .autodma = AUTODMA, - .bootable = OFF_BOARD, - },{ /* 2 */ - .name = "HPT302", - .init_setup = init_setup_hpt37x, - .init_chipset = init_chipset_hpt366, - .init_iops = init_iops_hpt366, - .init_hwif = init_hwif_hpt366, - .init_dma = init_dma_hpt366, - .channels = 2, - .autodma = AUTODMA, - .bootable = OFF_BOARD, - },{ /* 3 */ - .name = "HPT371", - .init_setup = init_setup_hpt37x, - .init_chipset = init_chipset_hpt366, - .init_iops = init_iops_hpt366, - .init_hwif = init_hwif_hpt366, - .init_dma = init_dma_hpt366, - .channels = 2, - .autodma = AUTODMA, - .bootable = OFF_BOARD, - },{ /* 4 */ - .name = "HPT374", - .init_setup = init_setup_hpt374, - .init_chipset = init_chipset_hpt366, - .init_iops = init_iops_hpt366, - .init_hwif = init_hwif_hpt366, - .init_dma = init_dma_hpt366, - .channels = 2, /* 4 */ - .autodma = AUTODMA, - .bootable = OFF_BOARD, - },{ /* 5 */ - .name = "HPT372N", - .init_setup = init_setup_hpt37x, - .init_chipset = init_chipset_hpt366, - .init_iops = init_iops_hpt366, - .init_hwif = init_hwif_hpt366, - .init_dma = init_dma_hpt366, - .channels = 2, /* 4 */ - .autodma = AUTODMA, - .bootable = OFF_BOARD, - } -}; - -/** - * hpt366_init_one - called when an HPT366 is found - * @dev: the hpt366 device - * @id: the matching pci id - * - * Called when the PCI registration layer (or the IDE initialization) - * finds a device matching our IDE device tables. - */ - -static int __devinit hpt366_init_one(struct pci_dev *dev, const struct pci_device_id *id) -{ - ide_pci_device_t *d = &hpt366_chipsets[id->driver_data]; - - return d->init_setup(dev, d); -} - -static struct pci_device_id hpt366_pci_tbl[] = { - { PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT366, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, - { PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT372, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1}, - { PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT302, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2}, - { PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT371, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 3}, - { PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT374, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4}, - { PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT372N, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 5}, - { 0, }, -}; -MODULE_DEVICE_TABLE(pci, hpt366_pci_tbl); - -static struct pci_driver driver = { - .name = "HPT366_IDE", - .id_table = hpt366_pci_tbl, - .probe = hpt366_init_one, -}; - -static int hpt366_ide_init(void) -{ - return ide_pci_register_driver(&driver); -} - -module_init(hpt366_ide_init); - -MODULE_AUTHOR("Andre Hedrick"); -MODULE_DESCRIPTION("PCI driver module for Highpoint HPT366 IDE"); -MODULE_LICENSE("GPL"); |